Invert the polarity of microSD voltage selector on Retronix R-Car V4H
Sparrow Hawk board. The voltage selector was not populated on prototype
EVTA1 boards, and is implemented slightly different on EVTB1 boards. As
the EVTA1 boards are from a limited run and generally not available,
update the DT to make it compatible with EVTB1 microSD voltage selector.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Enable support for PCIe based xHCI USB 3.0 driver and USB mass
storage support on Retronix R-Car V4H Sparrow Hawk board .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The R-Car V4H SoC before rev.3.0 can not support dual-rank LPDDR5 DRAM.
This affects 16 GiB dual-rank DRAM configuration of Retronix R-Car V4H
Sparrow Hawk board. Fall back to 8 GiB single-rank DRAM configuration
on such systems instead.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The Retronix R-Car V4H Sparrow Hawk old revision EVTA1 does not have MicroSD
voltage switch populated on the board, therefore the board supports only 3V3
and non-UHS MicroSD cards. While the EVTB1 board is populated with Winbond
W77Q51NW SPI NOR, the EVTA1 board is populated with Spansion S25FS512S SPI
NOR, those those SPI NOR IDs to discern the two board revisions and apply
the MicroSD related DT changes.
The MicroSD related DT changes modify the regulator node, which is now a
regulator-fixed and supplies only 3V3, and remove sd-uhs-sdr50 and
sd-uhs-sdr104 properties from the MicroSD slot controller node.
The MicroSD related DT changes cannot be applied as DTO, because the base
DT contains nodes which have to be removed in case of EVTA1, but have to
be present in case of EVTB1 and newer revisions of the board. Because the
EVTA1 is an old revision of the board that is not generally available, it
is better to special case it and keep the base DT compatible with EVTB1
and newer revisions of the board which are actually available.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
R-Car V4H Reference Manual R19UH0186EJ0130 Rev.1.30 Apr. 21, 2025
page 4581 Figure 104.3b Initial Setting of PCIEC(example) middle
of the figure indicates that fourth write into register 0x148 [2:0]
is 0x3 or GENMASK(1, 0). The current code writes GENMASK(11, 0)
which is a typo. Fix the typo.
Fixes: be3dd0dc2f ("pci: pcie-rcar-gen4: Add Renesas R-Car Gen4 DW PCIe controller driver")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
In stmfx_read_reg there is duplicated code to detect ret < 0 and return
ret if so. Remove one version of it.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
In single_read there is a switch block with a default label. All cases
in the switch block, including the default, return directly. So any code
following the switch block is unreachable. Remove the unreachable code.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
The test for the interrupt LPDDR4_INTR_BIST_DONE is using a bitwise and
but the test is simple logic so use the more appropriate logical and.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
In j721e_wiz_probe the test for too many lanes jumps to the error exit
path without assigning an error code which could lead to calling code
silently ignoring the failure. Set the error code.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
In keystone_usb_init the return code from psc_enable_module should be
returned as is rather than being negated.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
A few timer drivers cannot build without access to some platform
specific header files. Express those requirements in Kconfig as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
port_id is an unsigned variable so cannot be negative. Remove the test
checking for port_id being less than 0.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
In am65_cpsw_phy_init it is not certain that ret will be assigned to
before it reaches the 'return ret' statement. Initialise ret to ensure
that ret is valid.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
In cs4340_upload_firmware a buffer is allocated with malloc but this is
never freed. The pointer to this buffer, addr, is not even kept
unchanged. But in some cases addr is not a buffer allocated by malloc.
Introduce the use of another pointer to keep track of the buffer and to
know if it needs to be freed.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
A few ram drivers cannot build without access to some platform
specific header files. Express those requirements in Kconfig as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
A few serial drivers cannot build without access to some platform
specific header files. Express those requirements in Kconfig as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
When calling writel we do not have a return value to check or pass
along. This function should therefore be void and not return what writel
gives us.
Signed-off-by: Tom Rini <trini@konsulko.com>
This driver makes calls to in8/out8(). On PowerPC these are separate and
real calls but elsewhere they are able to simply be wrappers to
inb/outb. Rework this logic to be able to build this driver on more
platforms.
Signed-off-by: Tom Rini <trini@konsulko.com>
The Marvell RTC rtc driver cannot build without access to some
platform specific header files. Express that requirements in Kconfig as
well.
Signed-off-by: Tom Rini <trini@konsulko.com>
The MPC83xx sysreset driver cannot build without access to some
architecture specific header files. Express that requirements in Kconfig
as well.
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
A few sound drivers cannot build without access to some platform
specific header files. Express those requirements in Kconfig as well.
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The Qualcomm Snapdragon "SoC" driver cannot build without access to some
ARM64 specific functionality. Express that requirements in Kconfig as
well.
Reviewed-by: Casey Connolly <casey.connolly@linaro.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
The TI IPU remoteproc driver cannot build without access to some
platform specific header files. Express that requirements in Kconfig as
well.
Signed-off-by: Tom Rini <trini@konsulko.com>
A few reset drivers cannot build without access to some platform
specific header files. Express those requirements in Kconfig as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
This driver references the logarithmic macros while relying on an
indirection inclusion of <linux/log2.h>. Add the missing include
directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
A few pwm drivers cannot build without access to some platform
specific header files. Express those requirements in Kconfig as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
A few pinctrl drivers cannot build without access to some platform
specific header files. Express those requirements in Kconfig as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
The symbol "SM" is a library symbol and should not be prompted for. It
should be selected by the drivers that use it. In this case we need to
add a SANDBOX_SM symbol for the sandbox driver. The meson SM driver
cannot build on other platforms, so add the appropriate dependency.
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
In do_e1000_spi_checksum a temporary buffer is allocated but never
freed. Add code to free on exit. Also refactor the code to make the exit
code common.
This issue found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
The bootmeth rauc should scan all partitions, in particular whole
devices, and not be a global method. There may exist multiple RAUC
systems on different devices and they should all be detected. This also
fixes a bug, where both a global bootflow and one using an actual,
complete device would be detected at the same time, when scanning for
valid bootflows.
Signed-off-by: Martin Schwan <m.schwan@phytec.de>
Tested-by: Wadim Egorov <w.egorov@phytec.de>
As part of renaming environment related Kconfig options,
ENV_MMC_SW_PARTITION was inadvertently changed from a string to a bool.
Correct this.
Fixes: ffc4914703 ("env: Rename ENV_MMC_PARTITION to ENV_MMC_SW_PARTITION")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
CI: https://source.denx.de/u-boot/custodians/u-boot-riscv/-/pipelines/27379
- Board: mbv: Prepare MBV for CI
- Board: MPFS Icicle Kit cleanup
- Board: Add Andes Voyager board support
- RISCV: Update SYS_BOOTM_LEN to commonly used value
- starfive: fix return code of `mac write_eeprom`
- arch/riscv/lib: update memmove and memcpy for big-endian
Change the shift patterns for the unaligned memory move and copy code
to deal with big-endian by definign macros to change the shfit left and
right to go the opposite way.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
When writing the EEPROM fails, the command usage help text is displayed
after the error message. We should only display the error message instead.
If writing the EEPROM fails, return CMD_RET_FAILURE (1) instead of
CMD_RET_USAGE (-1).
Fixes: aea1bd95b6 ("eeprom: starfive: Enable ID EEPROM configuration")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Acked-by: E Shattow <e@freeshell.de>
Introduce Voyager board specific code, including
- dram info
- shared cache enabling
Signed-off-by: Randolph Sheng-Kai Lin <randolph@andestech.com>
Signed-off-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Introduce the initial device tree support for Andes Voyager board.
We will convert to OF_UPSTREAM once the patch series for kernel is merged.
Signed-off-by: Randolph Sheng-Kai Lin <randolph@andestech.com>
Signed-off-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The Voyager is Andes' first RISC-V development board.
It is built around Qilai SoC,
which includes Andes AX45MP quad-core cluster.
Introduce the Kconfig entry for the Voyager board.
Signed-off-by: Randolph Sheng-Kai Lin <randolph@andestech.com>
Signed-off-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Explicitly specify the type by replacing macro with variable
to fix the possible compilation warning.
Signed-off-by: Leo Yu-Chi Liang <ycliang@andestech.com>
A new system controller driver has been created to make code modular and
improve and clean code. Update and remove functions to account for these
additional drivers.
Signed-off-by: Jamie Gibbons <jamie.gibbons@microchip.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Enable the MPFS mailbox and system controller drivers for use with the
Icicle kit. These functions are crucial for the board setup functions
that run in the Icicle board file - mpfs_icicle.c.
Signed-off-by: Jamie Gibbons <jamie.gibbons@microchip.com>
Acked-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This driver provides an interface to access the functions of the system
controller on the Microchip PolarFire SoC.
This driver includes functions to use the system controller to read
the device serial number.
Signed-off-by: Jamie Gibbons <jamie.gibbons@microchip.com>
Acked-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This driver adds support for the single mailbox channel of the MSS
system controller on the Microchip PolarFire SoC.
Signed-off-by: Jamie Gibbons <jamie.gibbons@microchip.com>
Acked-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Move ethernet mac address setting to ft_board_setup() to remove the need
for fdt set in custom boot script.
Signed-off-by: Jamie Gibbons <jamie.gibbons@microchip.com>
Acked-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Enable CONFIG_OF_BOARD_SETUP and other dependencies to allow the use of
the ft_board_setup() function to replace fdt set in boot scripts for
Microchip's MPFS Icicle kit.
Signed-off-by: Jamie Gibbons <jamie.gibbons@microchip.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
