There have been issues with autoboot on DB410c for years, where autoboot
gets interrupted by spurious input on the UART console. Back in 2021, I've
tried to fix this by inserting a delay before UART initialization, but it
has turned out this is not working reliably either.
It looks like the root cause has always been the lack of bias-pull-up,
which was causing the RX line to be floating when UART is disconnected.
The delay does not seem to be needed anymore when applying bias-pull-up,
so drop it again in favor of the proper fix.
This reverts commit ad7e967738.
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Tested-by: Alexey Minnekhanov <alexeymin@minlexx.ru>
Acked-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250908-db410c-autoboot-fixes-v2-2-316ed98e0143@linaro.org
Signed-off-by: Casey Connolly <kcxt@postmarketos.org>
The GPIOs on PM6350 work fine using the qcom_spmi_gpio driver and
enables the use of the Volume Up button Fairphone 4 smartphone.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Add the pm6150l regulator data found on the Qualcomm SM6350 platform.
The tables are imported from the Linux driver. The SMPS regulators were
not added now.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Add support for TLMM pin controller block (Top Level Mode Multiplexer)
on SM6350 SoC, with support for special pins.
Correct pin configuration is required for working debug UART and eMMC/SD
cards.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
This reverts commit 644b4650ee.
While the intention of the above commit is correct, it leads to test
failures in CI that need to be addressed at the same time.
Signed-off-by: Tom Rini <trini@konsulko.com>
This driver references the get_timer macro while relying on an
indirection inclusion of <time.h>. Add the missing include directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
A few spi drivers cannot build without access to some platform
specific header files. Express those requirements in Kconfig as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
A few clock drivers cannot build without access to some platform
specific header files. Express those requirements in Kconfig as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
There is nothing x86-centric in this include file, and moving it will
allow for some drivers to be compile-tested on sandbox.
Signed-off-by: Tom Rini <trini@konsulko.com>
When printing the contents of an lbaint_t variable we need to use LBAF
to print it in order to get the correct format type depending on 32 or
64bit-ness.
Signed-off-by: Tom Rini <trini@konsulko.com>
When printing the contents of an size_t variable we need to use z prefix
to the format character in order to get the correct format type
depending on 32 or 64bit-ness.
Signed-off-by: Tom Rini <trini@konsulko.com>
This feature requires that CFG_SYS_FLASH_BASE is defined and this in
turn is only done in the case of FLASH_CFI_DRIVER && !CFI_FLASH or in
other words, when DM_MTD is not enabled.
Signed-off-by: Tom Rini <trini@konsulko.com>
The function mtd_read_oob_bf is called by cmd/nand.c but does not have a
prototype in any header. Add this to include/linux/mtd/mtd.h as that is
the most logical place currently.
Fixes: 1fac577207 ("nand: Add a watch command")
Signed-off-by: Tom Rini <trini@konsulko.com>
In this header we make direct references to some dm/device.h functions
while not including the header directly. Add the missing include.
Signed-off-by: Tom Rini <trini@konsulko.com>
In nand_wait_ready there is a loop that includes a NULL check for
chip->dev_ready before it is dereferenced. Use a NULL check once the
loop is exited as well to cover the case where it exits due to a timeout
and it is therefore not known if chip->dev_ready is NULL or not.
This issue found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
ret maybe used uninitialised in some cases so instead
initialise it first to prevent this.
This issue was found by Smatch.
Fixes: 9671243e8d (cmd: mtd: Use the subcmd infrastructure to declare mtd sub-commands)
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
As the code is today, we get a warning about "select" statements on
"choice" options not doing anything. This is why for all of the boards
which had an 'imply MULTI_DTB_FIT_USER_DEFINED_AREA' they then also had
to set the option in the defconfig. Drop the imply lines here.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add UFS driver for UFS controller present on Renesas R-Car X5H R8A78000.
The controller uses different initialization code compared to previous
generation UFS controller present in Renesas R-Car S4 R8A779F0, and the
majority of the driver is the initialization, hence a new driver.
[Marek: Clean driver up, add SCMI reset handling, use read_poll_timeout(),
pass error values out of ufs_renesas_pre_init(), change the
compatible string to "renesas,r8a78000-ufs" to align with
previous generation "renesas,r8a779f0-ufs"]
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Tuyen Dang <tuyen.dang.xa@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20251028142335.18125-7-marek.vasut+renesas@mailbox.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
In _spi_get_bus_and_cs the check for stacked parallel support needing
multiple chip select support does a direct return on error. Instead it
should set the error code in ret and then use the unwind goto.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
