Remove setting of fdt_high to ~0, which disables device tree relocation,
from the default environment. Doing so prevents U-Boot from correcting
problems such as having an unaligned device tree and leads to various
failure modes in the OS.
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-By: Tim Harvey <tharvey@gateworks.com>
Remove setting of fdt_high to ~0, which disables device tree relocation,
from the default environment. Doing so prevents U-Boot from correcting
problems such as having an unaligned device tree and leads to various
failure modes in the OS.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
This board is just short of overflowing the size limit, disable
support for EFI partition since EFI support is already disabled,
and disable a couple of commands which are also likely unused to
keep the board below limit.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Soeren Moch <smoch@web.de>
OP-TEE requires a trusted RNG. This is provided by ELE on i.MX95. Start
the initialization of the ELE RNG context before OP-TEE startup to allow
OP-TEE to derive RNG later.
Signed-off-by: Ji Luo <ji.luo@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
This adds support for the Kontron Electronics OSM-S i.MX93 SoM
and the matching baseboard BL i.MX93.
The SoM hardware complies to the Open Standard Module (OSM) 1.1
specification, size S (https://sget.org/standards/osm).
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
The arch-level implementation should be used here so that
env_get_location() can be used on board-level.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
This adds support for the Kontron Electronics OSM-S i.MX8MP SoM
and the matching baseboard BL i.MX8MP.
The SoM hardware complies to the Open Standard Module (OSM) 1.1
specification, size S (https://sget.org/standards/osm).
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Since M2 and M2B share the same defconfig aside from one parameter, we
have a common configuration that also allows us to support addition of
new boards based on the M2 hardware.
Signed-off-by: Andrea Calabrese <andrea.calabrese@amarulasolutions.com>
Michael Walle <mwalle@kernel.org> says:
I'll soon post support for the Kontron SMARC-sAM67 u-boot support.
I'm still waiting for the linux device trees to be merged (in -next
right now) and then to be synced to the u-boot tree. That board
features two different RTCs and this will already support for these.
Link: https://lore.kernel.org/r/20251117103315.2212686-1-mwalle@kernel.org
Add support for the Microcrystal RV8263 and compatible RTCs. The
driver's name was taken from linux. It should work with any NXP PCF85063
compatible RTCs. It was tested with a RV8263.
Signed-off-by: Michael Walle <mwalle@kernel.org>
As u-boot doesn't have any loadable modules, tristate doesn't make
sense. Convert it to bool.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This merges a number of fixes from Marek Vasut that will allow us to
move to a newer dtc release (that enforces the 8 byte alignment
requirement that has long existed).
Make sure the correct PLATFORM_...FLAGS are assigned in each
case, consistently. Assign PLATFORM_ELFFLAGS for both LE and
BE case. The previous PLATFORM_CPPFLAGS makes no sense for
these particular parameters, which are passed to objcopy.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Make sure the end of U-Boot is at 8-byte aligned offset, not 4-byte
aligned offset. This allows safely appending DT at the end of U-Boot
with the guarantee that the DT will be at 8-byte aligned offset. This
8-byte alignment is now checked by newer libfdt 1.7.2 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The 'extension' test would set 'extension_overlay_addr' variable to
decimal 4096 due to conversion in python. The 'extension_overlay_addr'
is however sampled using env_get_hex("extension_overlay_addr", 0);
which converts the 4096 to 0x4096 and uses that as DT overlay address,
which is unaligned. Fix this by setting extension_overlay_addr to 0x1000
as intended, which is aligned.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Trivially fix the following warnings in sandbox DTs, which show up with
DTC 1.7.2. Assign pin groups less confusing node names with pins- prefix
to avoid confusing DT compiler into thinking the node is really a bus node:
"
arch/sandbox/dts/.test.dtb.pre.tmp:1831.20-1841.5: Warning (i2c_bus_bridge): /pinctrl/i2c: incorrect #address-cells for I2C bus
arch/sandbox/dts/.test.dtb.pre.tmp:1831.20-1841.5: Warning (i2c_bus_bridge): /pinctrl/i2c: incorrect #size-cells for I2C bus
arch/sandbox/dts/test.dtb: Warning (i2c_bus_reg): Failed prerequisite 'i2c_bus_bridge'
arch/sandbox/dts/.test.dtb.pre.tmp:1848.20-1856.5: Warning (spi_bus_bridge): /pinctrl/spi: incorrect #address-cells for SPI bus
arch/sandbox/dts/.test.dtb.pre.tmp:1848.20-1856.5: Warning (spi_bus_bridge): /pinctrl/spi: incorrect #size-cells for SPI bus
arch/sandbox/dts/test.dtb: Warning (spi_bus_reg): Failed prerequisite 'spi_bus_bridge'
"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Reviewed-by: Heiko Schocher <hs@nabladev.com>
Trivially fix the following warnings in sandbox DTs, which show up with
DTC 1.7.2. Fill in the missing address and adjust emulated I2C address
to fit the 7bit address limit:
"
arch/sandbox/dts/sandbox.dtsi:138.30-140.5: Warning (i2c_bus_reg): /i2c@0/sandbox_pmic: I2C bus unit address format error, expected "40"
arch/sandbox/dts/sandbox.dtsi:146.18-161.5: Warning (i2c_bus_reg): /i2c@0/emul: I2C bus unit address format error, expected "ff"
arch/sandbox/dts/sandbox.dtsi:148.4-17: Warning (i2c_bus_reg): /i2c@0/emul:reg: I2C address must be less than 7-bits, got "0xff". Set I2C_TEN_BIT_ADDRESS for 10 bit addresses or fix the property
"
"
arch/sandbox/dts/.test.dtb.pre.tmp:912.18-926.5: Warning (i2c_bus_reg): /i2c@0/emul: I2C bus unit address format error, expected "ff"
arch/sandbox/dts/.test.dtb.pre.tmp:913.4-17: Warning (i2c_bus_reg): /i2c@0/emul:reg: I2C address must be less than 7-bits, got "0xff". Set I2C_TEN_BIT_ADDRESS for 10 bit addresses or fix the property
arch/sandbox/dts/.test.dtb.pre.tmp:928.30-931.5: Warning (i2c_bus_reg): /i2c@0/sandbox_pmic: I2C bus unit address format error, expected "40"
"
Fix up pmic test to match.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Heiko Schocher <hs@nabladev.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Make sure the end of U-Boot is at 8-byte aligned offset, not 4-byte
aligned offset. This allows safely appending DT at the end of U-Boot
with the guarantee that the DT will be at 8-byte aligned offset. This
8-byte alignment is now checked by newer libfdt 1.7.2 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The fdt_high and initrd_high have nasty side-effects , which may lead
to DT placed at 4-byte aligned offset when used in place, which then
prevents Linux on arm64 from booting. This is difficult to debug and
inobvious, with little to no gain. Remove this to let U-Boot place the
DT at correctly aligned address.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The fitImage may contain FDT at 4-byte aligned address, because alignment
of DT tags is 4 bytes. However, libfdt and also Linux expects DT to be at
8-byte aligned address. Make sure that the DTs embedded in fitImages are
always used from 8-byte aligned addresses. In case the DT is decompressed,
make sure the target buffer is 8-byte aligned. In case the DT is only
loaded, make sure the target buffer is 8-byte aligned too.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The SCMI shared memory area is no longer automatically marked as
non-cacheable after the commit a5a0134570 ("firmware: scmi: Drop
mmu_set_region_dcache_behaviour() misuse").
This change in behavior cause Rockchip RK3588 boards to fail boot with:
SoC: RK3588
DRAM: 8 GiB
scmi-over-smccc scmi: Channel unexpectedly busy
scmi_base_drv scmi-base.0: getting protocol version failed
scmi-over-smccc scmi: failed to probe base protocol
initcall_run_r(): initcall initr_dm() failed
### ERROR ### Please RESET the board ###
Update the memory mapping on RK3588 to mark the SCMI shared memory area
as non-cacheable to fix the SCMI shared memory based transport issue
that prevented RK3588 boards from booting.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Fix two memory allocation bugs in label_boot_extension():
1. When label->fdtdir is not set, overlay_dir was used without any
memory allocation.
2. When label->fdtdir is set, the allocation size was incorrect,
using 'len' (just the fdtdir length) instead of 'dir_len' (which
includes the trailing slash and null terminator).
Resolve both issues by moving the memory allocation and string
formatting outside the conditional block, resulting in clearer code
flow and correct sizing in all cases.
Closes: https://lists.denx.de/pipermail/u-boot/2025-November/602892.html
Addresses-Coverity-ID: 638558 Memory - illegal accesses (UNINIT)
Fixes: 935109cd9e ("boot: pxe_utils: Add extension board devicetree overlay support")
Signed-off-by: Kory Maincent (TI.com) <kory.maincent@bootlin.com>
Tested-by: Surkov Kirill <fanra3.tk@gmail.com>
Size of array buf was incorrect due to sizeof returning the
size of an integer (typically 32 bits) instead of a u64 type
(64 bits). Hence, buf array was shorter than expected.
Signed-off-by: Francois Berder <fberder@outlook.fr>
Reviewed-by: Simon Glass <sjg@chromium.org>
Pull request efi-2026-01-rc3-2
CIL https://source.denx.de/u-boot/custodians/u-boot-efi/-/pipelines/28454
Documentation:
* board: ti: am6254atl_sk: correct value of PRELOADED_BL33_BASE
* pytest: fix u-boot-test-flash typo
* samsung: Fix PXE description for the E850-96 board
* board: ti: k3: Update TI firmware repository URL to GitHub
* add missing macro descriptions to include/test/ut.h and add it to
the API documenation
* rearrange the description of DM tests and describe return values
Testing:
* Enable CI testing ACPI on qemu-riscv64_smode_acpi_defconfig
* Add qemu-riscv64_smode_defconfig to the CI tests
* Generalize tests such that they can run on RISC-V QEMU
- fdt_test_apply requires CONFIG_OF_LIBFDT_OVERLAY
- cmd/fdt: do not assume RNG device exists
- cmd/bdinfo: make no flash assumption
- cmd/bdinfo: consider arch_print_bdinfo() output
- common/print: do not use fixed buffer addresses
- cmd/fdt: do not use fixed buffer addresses
- raise CONFIG_CONSOLE_RECORD_OUT_SIZE default to 0x6000
* enable CONFIG_CONSOLE_RECORD=y on qemu-riscv64_smode_acpi
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEbcT5xx8ppvoGt20zxIHbvCwFGsQFAmkg1IsACgkQxIHbvCwF
# GsQVLA//dmiApob+J9FUhD8joD+DaKSNfLYmv8zwfIFL2xRxx7D+CQT+r+I9FJYI
# KojiLyn4PE/5VOm+wrsvAoYoMLJwAHvg5nmYJLLzvm6V//DLd1AEopP/+Uh8gEVW
# xYGLcvDyGgZpraAhcmqRnAS89py3SigwGzhcUMbT6ZC6pgMVEsBpg8XeMpY7N05c
# rwyqFAAPD8RcF7veQCpry87NiK5o+9YuM1zKl5sDFOpEWKq5ToNwhQ00bnux9lUd
# HWz9X6ge58iFiMXRqUCnOaPeXeChn9ejyEiKtfQ0JtykOf9NT2WMdD2VKe9PCYsd
# f7OynJTGG2OXTKBhon/xj75itiTm7EELc/FHwHEdtZIIHgpi/C33yQgKxLf9mtUo
# Z7DKYpPoaTCbJhs9LCK942KPtshbtAJLKTVqyBPo7Jn0mneeCQUsbaQRU7JruJTK
# hKluUjsAry3Do3wv/w6B8R6MMgfpBktPkqjg9e/maSdhYdkNAYpjajtORgpqmJRV
# HTGJXfL3qFC50jlenlMYOm4Qake33MIMzubaxoM3j5ENDUJ7KAbWADEoWDpve8Tu
# b/fX8uuW+g2T18Y/M9Bsk/jaUjDTx0xtZUSYNIIQJFDaJMzUxGYWlmtXhLZwFU8g
# 7S5pBmgxoSAtQSMAeoJPJp9FSgXYqiGLUeSwcOH2NaPn0lLFvK0=
# =D0Yy
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 21 Nov 2025 03:07:23 PM CST
# gpg: using RSA key 6DC4F9C71F29A6FA06B76D33C481DBBC2C051AC4
# gpg: Good signature from "Heinrich Schuchardt <xypron.glpk@gmx.de>" [unknown]
# gpg: aka "[jpeg image of size 1389]" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 6DC4 F9C7 1F29 A6FA 06B7 6D33 C481 DBBC 2C05 1AC4
Fix typo: `s/u-boot-test-flash1/u-boot-test-flash/`. The correct name of
the script doesn't have a "1" in it.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
As stated in PXELINUX doc [1], the PXE configuration file has to be in
the format of "01-MAC-address" for Ethernet connections:
The hardware type (using its ARP "htype" code) and address, all in
lowercase hexadecimal with dash separators. For example, for an
Ethernet (i.e. ARP hardware type "1") with address
"88:99:AA:BB:CC:DD", it would search for the filename
"01-88-99-aa-bb-cc-dd".
Indeed, PXE implementation in U-Boot looks for files like that, as can
be seen from this call chain:
format_mac_pxe()
pxe_mac_path()
pxe_get()
extlinux_pxe_read_bootflow()
Mention the fact that PXE expects the configuration file to be prepended
with "01" in the PXE section of E850-96 documentation. While at it, fix
some other minor issues in PXE section.
[1] https://wiki.syslinux.org/wiki/index.php?title=PXELINUX
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
The SPL_TEXT_BASE for AM62x SiP is set as 0x82000000 whereas the
documentation states 0x81880000 as the PRELOADED_BL33_BASE value.
Both should match to allow TFA to jump to the address where A53 SPL has
been loaded.
Signed-off-by: Anshul Dalal <anshuld@ti.com>
Acked-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Update the TI firmware repository URL from git.ti.com to the
GitHub mirror at github.com/TexasInstruments/ti-linux-firmware
which is much more reliable.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reported-by: Tom Rini <trini@konsulko.com>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
QEMU comes with its own OpenSBI. For running RISC-V virtual machine
using one of qemu-riscv64_smode_defconfig or
qemu-riscv64_smode_acpi_defconfig is the natural choice.
Add the riscv64 smode configurations to the test scope.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
For some tests the current default of 0x400 for
CONFIG_CONSOLE_RECORD_OUT_SIZE is too small.
Raise the value to 0x6000 which is already the most common value.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The location of memory depends on the board. Do not assume memory at fixed
memory locations. Use memalign() instead to allocate a buffer.
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The location of memory depends on the board. Do not assume memory at fixed
memory locations. Use calloc() instead to allocate buffers.
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
