Move TRAB burn-in tests to TRAB board directory

CHANGELOG

@@ -2,6 +2,13 @@
 Changes for U-Boot 1.0.0:
 ======================================================================
 
+* Patch by Stefan Roese, 12 Sep 2003:
+  - new boards added: DP405, HUB405, PLU405, VOH405
+  - some esd boards updated
+  - cpu/ppc4xx/sdram.c: disable memory controller before setting
+    first values
+  - cpu/ppc4xx/405_pci.c: set vendor id on PPC405EP systems
+
 * Patch by Martin Krause, 11 Sep 2003:
   add burn-in tests for TRAB board
 

MAINTAINERS

@@ -109,7 +109,7 @@ Dave Ellis <DGE@sixnetio.com>
 	SXNI855T		MPC8xx
 
 Raghu Krishnaprasad <raghu.krishnaprasad@fci.com>
-	
+
 	ADDERII			MPC852T
 
 Thomas Frieden <ThomasF@hyperion-entertainment.com>
@@ -200,11 +200,15 @@ Stefan Roese <stefan.roese@esd-electronics.com>
 	CPCI440			PPC440GP
 	CPCIISER4		PPC405GP
 	DASA_SIM		IOP480 (PPC401)
+	DP405			PPC405EP
 	DU405			PPC405GP
+	HUB405			PPC405EP
 	OCRTC			PPC405GP
 	ORSG			PPC405GP
 	PCI405			PPC405GP
+	PLU405			PPC405EP
 	PMC405			PPC405GP
+	VOH405			PPC405EP
 
 Peter De Schrijver <p2@mind.be>
 

MAKEALL

@@ -56,10 +56,11 @@ LIST_4xx="	\
 	ADCIOP		AR405		ASH405          BUBINGA405EP    \
 	CANBT		CPCI405		CPCI4052 	CPCI405AB       \
 	CPCI440         CPCIISER4	CRAYL1  	DASA_SIM	\
-	DU405    	EBONY           ERIC  		EXBITGEN	\
-	MIP405  	MIP405T		ML2		OCRTC		\
-	ORSG		PCI405		PIP405		PMC405          \
-	PPChameleonEVB	W7OLMC		W7OLMG          WALNUT405	\
+	DP405           DU405    	EBONY           ERIC  		\
+	EXBITGEN	HUB405          MIP405  	MIP405T		\
+	ML2		OCRTC		ORSG		PCI405		\
+	PIP405		PLU405          PMC405          PPChameleonEVB	\
+	VOH405          W7OLMC		W7OLMG          WALNUT405	\
 "
 
 #########################################################################

Makefile

@@ -76,6 +76,7 @@ export	CROSS_COMPILE
 
 # The "tools" are needed early, so put this first
 SUBDIRS	= tools \
+	  examples \
 	  lib_generic \
 	  lib_$(ARCH) \
 	  cpu/$(CPU) \
@@ -89,8 +90,7 @@ SUBDIRS	= tools \
 	  drivers \
 	  drivers/sk98lin \
 	  post \
-	  post/cpu \
-	  examples
+	  post/cpu
 
 #########################################################################
 # U-Boot objects....order is important (i.e. start must be first)
@@ -507,6 +507,9 @@ CRAYL1_config:unconfig
 DASA_SIM_config: unconfig
 	@./mkconfig $(@:_config=) ppc ppc4xx dasa_sim esd
 
+DP405_config:	unconfig
+	@./mkconfig $(@:_config=) ppc ppc4xx dp405 esd
+
 DU405_config:	unconfig
 	@./mkconfig $(@:_config=) ppc ppc4xx du405 esd
 
@@ -519,6 +522,9 @@ ERIC_config:unconfig
 EXBITGEN_config:unconfig
 	@./mkconfig $(@:_config=) ppc ppc4xx exbitgen
 
+HUB405_config:	unconfig
+	@./mkconfig $(@:_config=) ppc ppc4xx hub405 esd
+
 MIP405_config:unconfig
 	@./mkconfig $(@:_config=) ppc ppc4xx mip405 mpl
 
@@ -540,12 +546,18 @@ PCI405_config:	unconfig
 PIP405_config:unconfig
 	@./mkconfig $(@:_config=) ppc ppc4xx pip405 mpl
 
+PLU405_config:	unconfig
+	@./mkconfig $(@:_config=) ppc ppc4xx plu405 esd
+
 PMC405_config:	unconfig
 	@./mkconfig $(@:_config=) ppc ppc4xx pmc405 esd
 
 PPChameleonEVB_config:	unconfig
 	@./mkconfig $(@:_config=) ppc ppc4xx PPChameleonEVB dave
 
+VOH405_config:	unconfig
+	@./mkconfig $(@:_config=) ppc ppc4xx voh405 esd
+
 W7OLMC_config	\
 W7OLMG_config: unconfig
 	@./mkconfig $(@:_config=) ppc ppc4xx w7o
@@ -909,6 +921,7 @@ clean:
 	rm -f tools/gdb/astest tools/gdb/gdbcont tools/gdb/gdbsend
 	rm -f tools/env/fw_printenv tools/env/fw_setenv
 	rm -f board/cray/L1/bootscript.c board/cray/L1/bootscript.image
+	rm -f board/trab/trab_fkt
 
 clobber:	clean
 	find . -type f \

board/esd/ash405/ash405.c

@@ -239,11 +239,14 @@ int testdram (void)
 /* ------------------------------------------------------------------------- */
 
 #if (CONFIG_COMMANDS & CFG_CMD_NAND)
+#include <linux/mtd/nand.h>
+extern struct nand_chip nand_dev_desc[CFG_MAX_NAND_DEVICE];
 
 void nand_init(void)
 {
-	unsigned long totlen = nand_probe(CFG_NAND_BASE);
-
-	printf ("%4lu MB\n", totlen >> 20);
+	nand_probe(CFG_NAND_BASE);
+	if (nand_dev_desc[0].ChipID != NAND_ChipID_UNKNOWN) {
+		print_size(nand_dev_desc[0].totlen, "\n");
+	}
 }
 #endif

board/esd/common/xilinx_jtag/lenval.c

@@ -0,0 +1,217 @@
+/*
+ * (C) Copyright 2003
+ * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*******************************************************/
+/* file: lenval.c                                      */
+/* abstract:  This file contains routines for using    */
+/*            the lenVal data structure.               */
+/*******************************************************/
+
+#include <common.h>
+#include <asm/processor.h>
+
+#include "lenval.h"
+#include "ports.h"
+
+
+/*****************************************************************************
+ * Function:     value
+ * Description:  Extract the long value from the lenval array.
+ * Parameters:   plvValue    - ptr to lenval.
+ * Returns:      long        - the extracted value.
+ *****************************************************************************/
+long value( lenVal*     plvValue )
+{
+	long    lValue;         /* result to hold the accumulated result */
+	short   sIndex;
+
+	lValue  = 0;
+	for ( sIndex = 0; sIndex < plvValue->len ; ++sIndex )
+	{
+		lValue <<= 8;                       /* shift the accumulated result */
+		lValue |= plvValue->val[ sIndex];   /* get the last byte first */
+	}
+
+	return( lValue );
+}
+
+/*****************************************************************************
+ * Function:     initLenVal
+ * Description:  Initialize the lenval array with the given value.
+ *               Assumes lValue is less than 256.
+ * Parameters:   plv         - ptr to lenval.
+ *               lValue      - the value to set.
+ * Returns:      void.
+ *****************************************************************************/
+void initLenVal( lenVal*    plv,
+                 long       lValue )
+{
+	plv->len    = 1;
+	plv->val[0] = (unsigned char)lValue;
+}
+
+/*****************************************************************************
+ * Function:     EqualLenVal
+ * Description:  Compare two lenval arrays with an optional mask.
+ * Parameters:   plvTdoExpected  - ptr to lenval #1.
+ *               plvTdoCaptured  - ptr to lenval #2.
+ *               plvTdoMask      - optional ptr to mask (=0 if no mask).
+ * Returns:      short   - 0 = mismatch; 1 = equal.
+ *****************************************************************************/
+short EqualLenVal( lenVal*  plvTdoExpected,
+                   lenVal*  plvTdoCaptured,
+                   lenVal*  plvTdoMask )
+{
+	short           sEqual;
+	short           sIndex;
+	unsigned char   ucByteVal1;
+	unsigned char   ucByteVal2;
+	unsigned char   ucByteMask;
+
+	sEqual  = 1;
+	sIndex  = plvTdoExpected->len;
+
+	while ( sEqual && sIndex-- )
+	{
+		ucByteVal1  = plvTdoExpected->val[ sIndex ];
+		ucByteVal2  = plvTdoCaptured->val[ sIndex ];
+		if ( plvTdoMask )
+		{
+			ucByteMask  = plvTdoMask->val[ sIndex ];
+			ucByteVal1  &= ucByteMask;
+			ucByteVal2  &= ucByteMask;
+		}
+		if ( ucByteVal1 != ucByteVal2 )
+		{
+			sEqual  = 0;
+		}
+	}
+
+	return( sEqual );
+}
+
+
+/*****************************************************************************
+ * Function:     RetBit
+ * Description:  return the (byte, bit) of lv (reading from left to right).
+ * Parameters:   plv     - ptr to lenval.
+ *               iByte   - the byte to get the bit from.
+ *               iBit    - the bit number (0=msb)
+ * Returns:      short   - the bit value.
+ *****************************************************************************/
+short RetBit( lenVal*   plv,
+              int       iByte,
+              int       iBit )
+{
+	/* assert( ( iByte >= 0 ) && ( iByte < plv->len ) ); */
+	/* assert( ( iBit >= 0 ) && ( iBit < 8 ) ); */
+	return( (short)( ( plv->val[ iByte ] >> ( 7 - iBit ) ) & 0x1 ) );
+}
+
+/*****************************************************************************
+ * Function:     SetBit
+ * Description:  set the (byte, bit) of lv equal to val
+ * Example:      SetBit("00000000",byte, 1) equals "01000000".
+ * Parameters:   plv     - ptr to lenval.
+ *               iByte   - the byte to get the bit from.
+ *               iBit    - the bit number (0=msb).
+ *               sVal    - the bit value to set.
+ * Returns:      void.
+ *****************************************************************************/
+void SetBit( lenVal*    plv,
+             int        iByte,
+             int        iBit,
+             short      sVal )
+{
+	unsigned char   ucByteVal;
+	unsigned char   ucBitMask;
+
+	ucBitMask   = (unsigned char)(1 << ( 7 - iBit ));
+	ucByteVal   = (unsigned char)(plv->val[ iByte ] & (~ucBitMask));
+
+	if ( sVal )
+	{
+		ucByteVal   |= ucBitMask;
+	}
+	plv->val[ iByte ]   = ucByteVal;
+}
+
+/*****************************************************************************
+ * Function:     AddVal
+ * Description:  add val1 to val2 and store in resVal;
+ *               assumes val1 and val2  are of equal length.
+ * Parameters:   plvResVal   - ptr to result.
+ *               plvVal1     - ptr of addendum.
+ *               plvVal2     - ptr of addendum.
+ * Returns:      void.
+ *****************************************************************************/
+void addVal( lenVal*    plvResVal,
+             lenVal*    plvVal1,
+             lenVal*    plvVal2 )
+{
+	unsigned char   ucCarry;
+	unsigned short  usSum;
+	unsigned short  usVal1;
+	unsigned short  usVal2;
+	short           sIndex;
+
+	plvResVal->len  = plvVal1->len;         /* set up length of result */
+
+	/* start at least significant bit and add bytes    */
+	ucCarry = 0;
+	sIndex  = plvVal1->len;
+	while ( sIndex-- )
+	{
+		usVal1  = plvVal1->val[ sIndex ];   /* i'th byte of val1 */
+		usVal2  = plvVal2->val[ sIndex ];   /* i'th byte of val2 */
+
+		/* add the two bytes plus carry from previous addition */
+		usSum   = (unsigned short)( usVal1 + usVal2 + ucCarry );
+
+		/* set up carry for next byte */
+		ucCarry = (unsigned char)( ( usSum > 255 ) ? 1 : 0 );
+
+		/* set the i'th byte of the result */
+		plvResVal->val[ sIndex ]    = (unsigned char)usSum;
+	}
+}
+
+/*****************************************************************************
+ * Function:     readVal
+ * Description:  read from XSVF numBytes bytes of data into x.
+ * Parameters:   plv         - ptr to lenval in which to put the bytes read.
+ *               sNumBytes   - the number of bytes to read.
+ * Returns:      void.
+ *****************************************************************************/
+void readVal( lenVal*   plv,
+              short     sNumBytes )
+{
+	unsigned char*  pucVal;
+
+	plv->len    = sNumBytes;        /* set the length of the lenVal        */
+	for ( pucVal = plv->val; sNumBytes; --sNumBytes, ++pucVal )
+	{
+		/* read a byte of data into the lenVal */
+		readByte( pucVal );
+	}
+}

board/esd/common/xilinx_jtag/lenval.h

@@ -0,0 +1,79 @@
+/*
+ * (C) Copyright 2003
+ * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*******************************************************/
+/* file: lenval.h                                      */
+/* abstract:  This file contains a description of the  */
+/*            data structure "lenval".                 */
+/*******************************************************/
+
+#ifndef lenval_dot_h
+#define lenval_dot_h
+
+/* the lenVal structure is a byte oriented type used to store an */
+/* arbitrary length binary value. As an example, the hex value   */
+/* 0x0e3d is represented as a lenVal with len=2 (since 2 bytes   */
+/* and val[0]=0e and val[1]=3d.  val[2-MAX_LEN] are undefined    */
+
+/* maximum length (in bytes) of value to read in        */
+/* this needs to be at least 4, and longer than the     */
+/* length of the longest SDR instruction.  If there is, */
+/* only 1 device in the chain, MAX_LEN must be at least */
+/* ceil(27/8) == 4.  For 6 devices in a chain, MAX_LEN  */
+/* must be 5, for 14 devices MAX_LEN must be 6, for 20  */
+/* devices MAX_LEN must be 7, etc..                     */
+/* You can safely set MAX_LEN to a smaller number if you*/
+/* know how many devices will be in your chain.         */
+#define MAX_LEN 7000
+
+
+typedef struct var_len_byte
+{
+	short len;   /* number of chars in this value */
+	unsigned char val[MAX_LEN+1];  /* bytes of data */
+} lenVal;
+
+
+/* return the long representation of a lenVal */
+extern long value(lenVal *x);
+
+/* set lenVal equal to value */
+extern void initLenVal(lenVal *x, long value);
+
+/* check if expected equals actual (taking the mask into account) */
+extern short EqualLenVal(lenVal *expected, lenVal *actual, lenVal *mask);
+
+/* add val1+val2 and put the result in resVal */
+extern void addVal(lenVal *resVal, lenVal *val1, lenVal *val2);
+
+/* return the (byte, bit) of lv (reading from left to right) */
+extern short RetBit(lenVal *lv, int byte, int bit);
+
+/* set the (byte, bit) of lv equal to val (e.g. SetBit("00000000",byte, 1)
+   equals "01000000" */
+extern void SetBit(lenVal *lv, int byte, int bit, short val);
+
+/* read from XSVF numBytes bytes of data into x */
+extern void  readVal(lenVal *x, short numBytes);
+
+#endif

board/esd/common/xilinx_jtag/micro.h

@@ -0,0 +1,64 @@
+/*
+ * (C) Copyright 2003
+ * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*****************************************************************************
+ * File:         micro.h
+ * Description:  This header file contains the function prototype to the
+ *               primary interface function for the XSVF player.
+ * Usage:        FIRST - PORTS.C
+ *               Customize the ports.c function implementations to establish
+ *               the correct protocol for communicating with your JTAG ports
+ *               (setPort() and readTDOBit()) and tune the waitTime() delay
+ *               function.  Also, establish access to the XSVF data source
+ *               in the readByte() function.
+ *               FINALLY - Call xsvfExecute().
+ *****************************************************************************/
+#ifndef XSVF_MICRO_H
+#define XSVF_MICRO_H
+
+/* Legacy error codes for xsvfExecute from original XSVF player v2.0 */
+#define XSVF_LEGACY_SUCCESS 1
+#define XSVF_LEGACY_ERROR   0
+
+/* 4.04 [NEW] Error codes for xsvfExecute. */
+/* Must #define XSVF_SUPPORT_ERRORCODES in micro.c to get these codes */
+#define XSVF_ERROR_NONE         0
+#define XSVF_ERROR_UNKNOWN      1
+#define XSVF_ERROR_TDOMISMATCH  2
+#define XSVF_ERROR_MAXRETRIES   3   /* TDO mismatch after max retries */
+#define XSVF_ERROR_ILLEGALCMD   4
+#define XSVF_ERROR_ILLEGALSTATE 5
+#define XSVF_ERROR_DATAOVERFLOW 6   /* Data > lenVal MAX_LEN buffer size*/
+/* Insert new errors here */
+#define XSVF_ERROR_LAST         7
+
+/*****************************************************************************
+ * Function:     xsvfExecute
+ * Description:  Process, interpret, and apply the XSVF commands.
+ *               See port.c:readByte for source of XSVF data.
+ * Parameters:   none.
+ * Returns:      int - For error codes see above.
+ *****************************************************************************/
+int xsvfExecute(void);
+
+#endif  /* XSVF_MICRO_H */

board/esd/common/xilinx_jtag/ports.c

@@ -0,0 +1,116 @@
+/*
+ * (C) Copyright 2003
+ * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*******************************************************/
+/* file: ports.c                                       */
+/* abstract:  This file contains the routines to       */
+/*            output values on the JTAG ports, to read */
+/*            the TDO bit, and to read a byte of data  */
+/*            from the prom                            */
+/*                                                     */
+/*******************************************************/
+
+#include <common.h>
+#include <asm/processor.h>
+
+#include "ports.h"
+
+static unsigned long output = 0;
+static int filepos = 0;
+static int oldstate = 0;
+static int newstate = 0;
+static int readptr = 0;
+
+extern long filesize;
+extern const unsigned char fpgadata[];
+
+
+/* if in debugging mode, then just set the variables */
+void setPort(short p,short val)
+{
+	if (p==TMS) {
+		if (val) {
+			output |= JTAG_TMS;
+		} else {
+			output &= ~JTAG_TMS;
+		}
+	}
+	if (p==TDI) {
+		if (val) {
+			output |= JTAG_TDI;
+		} else {
+			output &= ~JTAG_TDI;
+		}
+	}
+	if (p==TCK) {
+		if (val) {
+			output |= JTAG_TCK;
+		} else {
+			output &= ~JTAG_TCK;
+		}
+		out32(GPIO0_OR, output);
+	}
+}
+
+
+/* toggle tck LH */
+void pulseClock(void)
+{
+	setPort(TCK,0);  /* set the TCK port to low  */
+	setPort(TCK,1);  /* set the TCK port to high */
+}
+
+
+/* read in a byte of data from the prom */
+void readByte(unsigned char *data)
+{
+	/* pretend reading using a file */
+	*data = fpgadata[readptr++];
+	newstate = (100 * filepos++) / filesize;
+	if (newstate != oldstate) {
+		printf("%4d\r\r\r\r", newstate);
+		oldstate = newstate;
+	}
+}
+
+/* read the TDO bit from port */
+unsigned char readTDOBit(void)
+{
+	unsigned long inputs;
+
+	inputs = in32(GPIO0_IR);
+	if (inputs & JTAG_TDO)
+		return 1;
+	else
+		return 0;
+}
+
+
+/* Wait at least the specified number of microsec.                           */
+/* Use a timer if possible; otherwise estimate the number of instructions    */
+/* necessary to be run based on the microcontroller speed.  For this example */
+/* we pulse the TCK port a number of times based on the processor speed.     */
+void waitTime(long microsec)
+{
+	udelay(microsec); /* esd */
+}

board/esd/common/xilinx_jtag/ports.h

@@ -0,0 +1,62 @@
+/*
+ * (C) Copyright 2003
+ * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*******************************************************/
+/* file: ports.h                                       */
+/* abstract:  This file contains extern declarations   */
+/*            for providing stimulus to the JTAG ports.*/
+/*******************************************************/
+
+#ifndef ports_dot_h
+#define ports_dot_h
+
+/* these constants are used to send the appropriate ports to setPort */
+/* they should be enumerated types, but some of the microcontroller  */
+/* compilers don't like enumerated types */
+#define TCK (short) 0
+#define TMS (short) 1
+#define TDI (short) 2
+
+/*
+ * Use CFG_FPGA_xxx defines from board include file.
+ */
+#define JTAG_TMS   CFG_FPGA_PRG     /* output */
+#define JTAG_TCK   CFG_FPGA_CLK     /* output */
+#define JTAG_TDI   CFG_FPGA_DATA    /* output */
+#define JTAG_TDO   CFG_FPGA_DONE    /* input */
+
+/* set the port "p" (TCK, TMS, or TDI) to val (0 or 1) */
+void setPort(short p, short val);
+
+/* read the TDO bit and store it in val */
+unsigned char readTDOBit(void);
+
+/* make clock go down->up->down*/
+void pulseClock(void);
+
+/* read the next byte of data from the xsvf file */
+void readByte(unsigned char *data);
+
+void waitTime(long microsec);
+
+#endif

board/esd/cpci405/cpci405.c

@@ -433,7 +433,14 @@ int checkboard (void)
 #endif
 
 	if (ctermm2()) {
-		printf("CTERM-M2 - Id=0x%02x)", *(unsigned char *)0xf0000400);
+		unsigned char str[4];
+
+		/*
+		 * Read board-id and save in env-variable
+		 */
+		sprintf(str, "%d", *(unsigned char *)0xf0000400);
+		setenv("boardid", str);
+		printf("CTERM-M2 - Id=%s)", str);
 	} else {
 		if (cpci405_host()) {
 			puts ("PCI Host Version)");
@@ -508,44 +515,144 @@ void ide_set_reset(int on)
 #endif /* CONFIG_IDE_RESET */
 #endif /* CONFIG_CPCI405_VER2 */
 
-#if 0 /* test-only */
-/* ------------------------------------------------------------------------- */
 
-u8 *dhcp_vendorex_prep (u8 * e)
+#ifdef CONFIG_CPCI405AB
+
+#define ONE_WIRE_CLEAR   (*(volatile unsigned short *)0xf0400000 |= 0x0100)
+#define ONE_WIRE_SET     (*(volatile unsigned short *)0xf0400000 &= ~0x0100)
+#define ONE_WIRE_GET     (*(volatile unsigned short *)0xf0400002 & 0x1000)
+
+/*
+ * Generate a 1-wire reset, return 1 if no presence detect was found,
+ * return 0 otherwise.
+ * (NOTE: Does not handle alarm presence from DS2404/DS1994)
+ */
+int OWTouchReset(void)
 {
-	char *ptr;
+	int result;
 
-/* DHCP vendor-class-identifier = 60 */
-	if ((ptr = getenv ("dhcp_vendor-class-identifier"))) {
-		*e++ = 60;
-		*e++ = strlen (ptr);
-		while (*ptr)
-			*e++ = *ptr++;
-	}
-/* my DHCP_CLIENT_IDENTIFIER = 61 */
-	if ((ptr = getenv ("dhcp_client_id"))) {
-		*e++ = 61;
-		*e++ = strlen (ptr);
-		while (*ptr)
-			*e++ = *ptr++;
-	}
+	ONE_WIRE_CLEAR;
+	udelay(480);
+	ONE_WIRE_SET;
+	udelay(70);
 
-	return e;
+	result = ONE_WIRE_GET;
+
+	udelay(410);
+	return result;
 }
 
 
-/* ------------------------------------------------------------------------- */
-
-u8 *dhcp_vendorex_proc (u8 * popt)
+/*
+ * Send 1 a 1-wire write bit.
+ * Provide 10us recovery time.
+ */
+void OWWriteBit(int bit)
 {
-	if (*popt == 61)
-		return (u8 *)-1;
-	if (*popt == 43) {
-		printf("|%s|", popt+4); /* test-only */
-		return (u8 *)-1;
+	if (bit) {
+		/*
+		 * write '1' bit
+		 */
+		ONE_WIRE_CLEAR;
+		udelay(6);
+		ONE_WIRE_SET;
+		udelay(64);
+	} else {
+		/*
+		 * write '0' bit
+		 */
+		ONE_WIRE_CLEAR;
+		udelay(60);
+		ONE_WIRE_SET;
+		udelay(10);
 	}
-	return NULL;
 }
 
-/* ------------------------------------------------------------------------- */
-#endif /* test-only */
+
+/*
+ * Read a bit from the 1-wire bus and return it.
+ * Provide 10us recovery time.
+ */
+int OWReadBit(void)
+{
+	int result;
+
+	ONE_WIRE_CLEAR;
+	udelay(6);
+	ONE_WIRE_SET;
+	udelay(9);
+
+	result = ONE_WIRE_GET;
+
+	udelay(55);
+	return result;
+}
+
+
+void OWWriteByte(int data)
+{
+	int loop;
+
+	for (loop=0; loop<8; loop++) {
+		OWWriteBit(data & 0x01);
+		data >>= 1;
+	}
+}
+
+
+int OWReadByte(void)
+{
+	int loop, result = 0;
+
+	for (loop=0; loop<8; loop++) {
+		result >>= 1;
+		if (OWReadBit()) {
+			result |= 0x80;
+		}
+	}
+
+	return result;
+}
+
+
+int do_onewire(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+	volatile unsigned short val;
+	int result;
+	int i;
+	unsigned char ow_id[6];
+	unsigned char str[32];
+	unsigned char ow_crc;
+
+	/*
+	 * Clear 1-wire bit (open drain with pull-up)
+	 */
+	val = *(volatile unsigned short *)0xf0400000;
+	val &= ~0x1000; /* clear 1-wire bit */
+	*(volatile unsigned short *)0xf0400000 = val;
+
+	result = OWTouchReset();
+	if (result != 0) {
+		puts("No 1-wire device detected!\n");
+	}
+
+	OWWriteByte(0x33); /* send read rom command */
+	OWReadByte(); /* skip family code ( == 0x01) */
+	for (i=0; i<6; i++) {
+		ow_id[i] = OWReadByte();
+	}
+	ow_crc = OWReadByte(); /* read crc */
+
+	sprintf(str, "%08X%04X", *(unsigned int *)&ow_id[0], *(unsigned short *)&ow_id[4]);
+	printf("Setting environment variable 'ow_id' to %s\n", str);
+	setenv("ow_id", str);
+
+	return 0;
+}
+U_BOOT_CMD(
+	onewire,	1,	1,	do_onewire,
+	"onewire - Read 1-write ID\n",
+	NULL
+	);
+
+#endif /* CONFIG_CPCI405AB */

board/esd/dp405/Makefile

@@ -0,0 +1,51 @@
+#
+# (C) Copyright 2000
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+# Objects for Xilinx JTAG programming (CPLD)
+CPLD    = ../common/xilinx_jtag/lenval.o \
+	  ../common/xilinx_jtag/micro.o \
+	  ../common/xilinx_jtag/ports.o
+
+OBJS	= $(BOARD).o flash.o $(CPLD)
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) crv $@ $(OBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+sinclude .depend
+
+#########################################################################

board/esd/dp405/config.mk

@@ -0,0 +1,29 @@
+#
+# (C) Copyright 2000
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# esd VOH405 boards
+#
+
+TEXT_BASE = 0xFFFC0000
+#TEXT_BASE = 0x00FC0000

board/esd/dp405/dp405.c

@@ -0,0 +1,143 @@
+/*
+ * (C) Copyright 2001-2003
+ * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/processor.h>
+#include <command.h>
+#include <malloc.h>
+
+
+/* fpga configuration data - not compressed, generated by bin2c */
+const unsigned char fpgadata[] =
+{
+#include "fpgadata.c"
+};
+int filesize = sizeof(fpgadata);
+
+
+int board_pre_init (void)
+{
+	/*
+	 * IRQ 0-15  405GP internally generated; active high; level sensitive
+	 * IRQ 16    405GP internally generated; active low; level sensitive
+	 * IRQ 17-24 RESERVED
+	 * IRQ 25 (EXT IRQ 0) CAN0; active low; level sensitive
+	 * IRQ 26 (EXT IRQ 1) SER0 ; active low; level sensitive
+	 * IRQ 27 (EXT IRQ 2) SER1; active low; level sensitive
+	 * IRQ 28 (EXT IRQ 3) FPGA 0; active low; level sensitive
+	 * IRQ 29 (EXT IRQ 4) FPGA 1; active low; level sensitive
+	 * IRQ 30 (EXT IRQ 5) PCI INTA; active low; level sensitive
+	 * IRQ 31 (EXT IRQ 6) COMPACT FLASH; active high; level sensitive
+	 */
+	mtdcr(uicsr, 0xFFFFFFFF);       /* clear all ints */
+	mtdcr(uicer, 0x00000000);       /* disable all ints */
+	mtdcr(uiccr, 0x00000000);       /* set all to be non-critical*/
+	mtdcr(uicpr, 0xFFFFFF80);       /* set int polarities */
+	mtdcr(uictr, 0x10000000);       /* set int trigger levels */
+	mtdcr(uicvcr, 0x00000001);      /* set vect base=0,INT0 highest priority*/
+	mtdcr(uicsr, 0xFFFFFFFF);       /* clear all ints */
+
+	/*
+	 * EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 15 us
+	 */
+	mtebc (epcr, 0xa8400000); /* ebc always driven */
+
+	return 0;
+}
+
+
+/* ------------------------------------------------------------------------- */
+
+int misc_init_f (void)
+{
+	return 0;  /* dummy implementation */
+}
+
+
+int misc_init_r (void)
+{
+	/*
+	 * Reset CPLD via GPIO13 (CS4) pin
+	 */
+	out32(GPIO0_OR, in32(GPIO0_OR) & ~(0x80000000 >> 13));
+	udelay(1000); /* wait 1ms */
+	out32(GPIO0_OR, in32(GPIO0_OR) | (0x80000000 >> 13));
+	udelay(1000); /* wait 1ms */
+
+	return (0);
+}
+
+
+/*
+ * Check Board Identity:
+ */
+
+int checkboard (void)
+{
+	unsigned char str[64];
+	int i = getenv_r ("serial#", str, sizeof(str));
+	unsigned char trans[16] = {0x0,0x8,0x4,0xc,0x2,0xa,0x6,0xe,
+                                   0x1,0x9,0x5,0xd,0x3,0xb,0x7,0xf};
+	unsigned char id1, id2;
+
+	puts ("Board: ");
+
+	if (i == -1) {
+		puts ("### No HW ID - assuming DP405");
+	} else {
+		puts(str);
+	}
+
+	id1 = trans[(~(in32(GPIO0_IR) >> 5)) & 0x0000000f];
+	id2 = trans[(~(in32(GPIO0_IR) >> 9)) & 0x0000000f];
+	printf(" (ID=0x%1X%1X)\n", id1, id2);
+
+	return 0;
+}
+
+/* ------------------------------------------------------------------------- */
+
+long int initdram (int board_type)
+{
+	unsigned long val;
+
+	mtdcr(memcfga, mem_mb0cf);
+	val = mfdcr(memcfgd);
+
+#if 0
+	printf("\nmb0cf=%x\n", val); /* test-only */
+	printf("strap=%x\n", mfdcr(strap)); /* test-only */
+#endif
+
+	return (4*1024*1024 << ((val & 0x000e0000) >> 17));
+}
+
+/* ------------------------------------------------------------------------- */
+
+int testdram (void)
+{
+	/* TODO: XXX XXX XXX */
+	printf ("test: 16 MB - ok\n");
+
+	return (0);
+}

board/esd/dp405/flash.c

@@ -0,0 +1,101 @@
+/*
+ * (C) Copyright 2001
+ * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <ppc4xx.h>
+#include <asm/processor.h>
+
+/*
+ * include common flash code (for esd boards)
+ */
+#include "../common/flash.c"
+
+/*-----------------------------------------------------------------------
+ * Functions
+ */
+static ulong flash_get_size (vu_long * addr, flash_info_t * info);
+static void flash_get_offsets (ulong base, flash_info_t * info);
+
+/*-----------------------------------------------------------------------
+ */
+
+unsigned long flash_init (void)
+{
+	unsigned long size_b0;
+	int i;
+	uint pbcr;
+	unsigned long base_b0;
+	int size_val = 0;
+
+	/* Init: no FLASHes known */
+	for (i=0; i<CFG_MAX_FLASH_BANKS; ++i) {
+		flash_info[i].flash_id = FLASH_UNKNOWN;
+	}
+
+	/* Static FLASH Bank configuration here - FIXME XXX */
+
+	size_b0 = flash_get_size((vu_long *)FLASH_BASE0_PRELIM, &flash_info[0]);
+
+	if (flash_info[0].flash_id == FLASH_UNKNOWN) {
+		printf ("## Unknown FLASH on Bank 0 - Size = 0x%08lx = %ld MB\n",
+			size_b0, size_b0<<20);
+	}
+
+	/* Setup offsets */
+	flash_get_offsets (-size_b0, &flash_info[0]);
+
+	/* Re-do sizing to get full correct info */
+	mtdcr(ebccfga, pb0cr);
+	pbcr = mfdcr(ebccfgd);
+	mtdcr(ebccfga, pb0cr);
+	base_b0 = -size_b0;
+	switch (size_b0) {
+	case 1 << 20:
+		size_val = 0;
+		break;
+	case 2 << 20:
+		size_val = 1;
+		break;
+	case 4 << 20:
+		size_val = 2;
+		break;
+	case 8 << 20:
+		size_val = 3;
+		break;
+	case 16 << 20:
+		size_val = 4;
+		break;
+	}
+	pbcr = (pbcr & 0x0001ffff) | base_b0 | (size_val << 17);
+	mtdcr(ebccfgd, pbcr);
+
+	/* Monitor protection ON by default */
+	(void)flash_protect(FLAG_PROTECT_SET,
+			    -CFG_MONITOR_LEN,
+			    0xffffffff,
+			    &flash_info[0]);
+
+	flash_info[0].size = size_b0;
+
+	return (size_b0);
+}

board/esd/dp405/u-boot.lds

@@ -0,0 +1,148 @@
+/*
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+/* Do we need any of these for elf?
+   __DYNAMIC = 0;    */
+SECTIONS
+{
+  .resetvec 0xFFFFFFFC :
+  {
+    *(.resetvec)
+  } = 0xffff
+
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)		}
+  .rela.text     : { *(.rela.text) 	}
+  .rel.data      : { *(.rel.data)		}
+  .rela.data     : { *(.rela.data) 	}
+  .rel.rodata    : { *(.rel.rodata) 	}
+  .rela.rodata   : { *(.rela.rodata) 	}
+  .rel.got       : { *(.rel.got)		}
+  .rela.got      : { *(.rela.got)		}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)		}
+  .rela.bss      : { *(.rela.bss)		}
+  .rel.plt       : { *(.rel.plt)		}
+  .rela.plt      : { *(.rela.plt)		}
+  .init          : { *(.init)	}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    /* WARNING - the following is hand-optimized to fit within	*/
+    /* the sector layout of our flash chips!	XXX FIXME XXX	*/
+
+    cpu/ppc4xx/start.o	(.text)
+    cpu/ppc4xx/traps.o	(.text)
+    cpu/ppc4xx/interrupts.o	(.text)
+    cpu/ppc4xx/serial.o	(.text)
+    cpu/ppc4xx/cpu_init.o	(.text)
+    cpu/ppc4xx/speed.o	(.text)
+    cpu/ppc4xx/405gp_enet.o	(.text)
+    common/dlmalloc.o	(.text)
+    lib_generic/crc32.o		(.text)
+    lib_ppc/extable.o	(.text)
+    lib_generic/zlib.o		(.text)
+
+/*    . = env_offset;*/
+/*    common/environment.o(.text)*/
+
+    *(.text)
+    *(.fixup)
+    *(.got1)
+  }
+  _etext = .;
+  PROVIDE (etext = .);
+  .rodata    :
+  {
+    *(.rodata)
+    *(.rodata1)
+    *(.rodata.str1.4)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x00FF) & 0xFFFFFF00;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
+  __fixup_entries = (. - _FIXUP_TABLE_)>>2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  __u_boot_cmd_start = .;
+  .u_boot_cmd : { *(.u_boot_cmd) }
+  __u_boot_cmd_end = .;
+
+
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(256);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(256);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+  _end = . ;
+  PROVIDE (end = .);
+}

board/esd/hub405/Makefile

@@ -0,0 +1,46 @@
+#
+# (C) Copyright 2000
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	= $(BOARD).o flash.o
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) crv $@ $(OBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+sinclude .depend
+
+#########################################################################

board/esd/hub405/config.mk

@@ -0,0 +1,28 @@
+#
+# (C) Copyright 2000
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# esd HUB405 boards
+#
+
+TEXT_BASE = 0xFFFC0000

board/esd/hub405/flash.c

@@ -0,0 +1,101 @@
+/*
+ * (C) Copyright 2001
+ * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <ppc4xx.h>
+#include <asm/processor.h>
+
+/*
+ * include common flash code (for esd boards)
+ */
+#include "../common/flash.c"
+
+/*-----------------------------------------------------------------------
+ * Functions
+ */
+static ulong flash_get_size (vu_long * addr, flash_info_t * info);
+static void flash_get_offsets (ulong base, flash_info_t * info);
+
+/*-----------------------------------------------------------------------
+ */
+
+unsigned long flash_init (void)
+{
+	unsigned long size_b0;
+	int i;
+	uint pbcr;
+	unsigned long base_b0;
+	int size_val = 0;
+
+	/* Init: no FLASHes known */
+	for (i=0; i<CFG_MAX_FLASH_BANKS; ++i) {
+		flash_info[i].flash_id = FLASH_UNKNOWN;
+	}
+
+	/* Static FLASH Bank configuration here - FIXME XXX */
+
+	size_b0 = flash_get_size((vu_long *)FLASH_BASE0_PRELIM, &flash_info[0]);
+
+	if (flash_info[0].flash_id == FLASH_UNKNOWN) {
+		printf ("## Unknown FLASH on Bank 0 - Size = 0x%08lx = %ld MB\n",
+			size_b0, size_b0<<20);
+	}
+
+	/* Setup offsets */
+	flash_get_offsets (-size_b0, &flash_info[0]);
+
+	/* Re-do sizing to get full correct info */
+	mtdcr(ebccfga, pb0cr);
+	pbcr = mfdcr(ebccfgd);
+	mtdcr(ebccfga, pb0cr);
+	base_b0 = -size_b0;
+	switch (size_b0) {
+	case 1 << 20:
+		size_val = 0;
+		break;
+	case 2 << 20:
+		size_val = 1;
+		break;
+	case 4 << 20:
+		size_val = 2;
+		break;
+	case 8 << 20:
+		size_val = 3;
+		break;
+	case 16 << 20:
+		size_val = 4;
+		break;
+	}
+	pbcr = (pbcr & 0x0001ffff) | base_b0 | (size_val << 17);
+	mtdcr(ebccfgd, pbcr);
+
+	/* Monitor protection ON by default */
+	(void)flash_protect(FLAG_PROTECT_SET,
+			    -CFG_MONITOR_LEN,
+			    0xffffffff,
+			    &flash_info[0]);
+
+	flash_info[0].size = size_b0;
+
+	return (size_b0);
+}

board/esd/hub405/hub405.c

@@ -0,0 +1,166 @@
+/*
+ * (C) Copyright 2001-2003
+ * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/processor.h>
+#include <command.h>
+#include <malloc.h>
+
+/* ------------------------------------------------------------------------- */
+
+
+int board_pre_init (void)
+{
+	/*
+	 * IRQ 0-15  405GP internally generated; active high; level sensitive
+	 * IRQ 16    405GP internally generated; active low; level sensitive
+	 * IRQ 17-24 RESERVED
+	 * IRQ 25 (EXT IRQ 0) CAN0; active low; level sensitive
+	 * IRQ 26 (EXT IRQ 1) SER0 ; active low; level sensitive
+	 * IRQ 27 (EXT IRQ 2) SER1; active low; level sensitive
+	 * IRQ 28 (EXT IRQ 3) FPGA 0; active low; level sensitive
+	 * IRQ 29 (EXT IRQ 4) FPGA 1; active low; level sensitive
+	 * IRQ 30 (EXT IRQ 5) PCI INTA; active low; level sensitive
+	 * IRQ 31 (EXT IRQ 6) COMPACT FLASH; active high; level sensitive
+	 */
+	mtdcr(uicsr, 0xFFFFFFFF);       /* clear all ints */
+	mtdcr(uicer, 0x00000000);       /* disable all ints */
+	mtdcr(uiccr, 0x00000000);       /* set all to be non-critical*/
+	mtdcr(uicpr, 0xFFFFFF9F);       /* set int polarities */
+	mtdcr(uictr, 0x10000000);       /* set int trigger levels */
+	mtdcr(uicvcr, 0x00000001);      /* set vect base=0,INT0 highest priority*/
+	mtdcr(uicsr, 0xFFFFFFFF);       /* clear all ints */
+
+	/*
+	 * EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 15 us
+	 */
+	mtebc (epcr, 0xa8400000); /* ebc always driven */
+
+	return 0;
+}
+
+
+/* ------------------------------------------------------------------------- */
+
+int misc_init_f (void)
+{
+	return 0;  /* dummy implementation */
+}
+
+
+int misc_init_r (void)
+{
+	volatile unsigned char *duart0_mcr = (unsigned char *)((ulong)DUART0_BA + 4);
+	volatile unsigned char *duart1_mcr = (unsigned char *)((ulong)DUART1_BA + 4);
+	volatile unsigned char *duart2_mcr = (unsigned char *)((ulong)DUART2_BA + 4);
+	volatile unsigned char *duart3_mcr = (unsigned char *)((ulong)DUART3_BA + 4);
+
+	/*
+	 * Reset external DUARTs
+	 */
+	out32(GPIO0_OR, in32(GPIO0_OR) | CFG_DUART_RST); /* set reset to high */
+	udelay(10); /* wait 10us */
+	out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_DUART_RST); /* set reset to low */
+	udelay(1000); /* wait 1ms */
+
+	/*
+	 * Enable interrupts in exar duart mcr[3]
+	 */
+	*duart0_mcr = 0x08;
+	*duart1_mcr = 0x08;
+	*duart2_mcr = 0x08;
+	*duart3_mcr = 0x08;
+
+	/*
+	 * Set NAND-FLASH GPIO signals to default
+	 */
+	out32(GPIO0_OR, in32(GPIO0_OR) & ~(CFG_NAND_CLE | CFG_NAND_ALE));
+	out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);
+
+	return (0);
+}
+
+
+/*
+ * Check Board Identity:
+ */
+
+int checkboard (void)
+{
+	unsigned char str[64];
+	int i = getenv_r ("serial#", str, sizeof(str));
+
+	puts ("Board: ");
+
+	if (i == -1) {
+		puts ("### No HW ID - assuming HUB405");
+	} else {
+		puts(str);
+	}
+
+	putc ('\n');
+
+	return 0;
+}
+
+/* ------------------------------------------------------------------------- */
+
+long int initdram (int board_type)
+{
+	unsigned long val;
+
+	mtdcr(memcfga, mem_mb0cf);
+	val = mfdcr(memcfgd);
+
+#if 0
+	printf("\nmb0cf=%x\n", val); /* test-only */
+	printf("strap=%x\n", mfdcr(strap)); /* test-only */
+#endif
+
+	return (4*1024*1024 << ((val & 0x000e0000) >> 17));
+}
+
+/* ------------------------------------------------------------------------- */
+
+int testdram (void)
+{
+	/* TODO: XXX XXX XXX */
+	printf ("test: 16 MB - ok\n");
+
+	return (0);
+}
+
+/* ------------------------------------------------------------------------- */
+
+#if (CONFIG_COMMANDS & CFG_CMD_NAND)
+#include <linux/mtd/nand.h>
+extern struct nand_chip nand_dev_desc[CFG_MAX_NAND_DEVICE];
+
+void nand_init(void)
+{
+	nand_probe(CFG_NAND_BASE);
+	if (nand_dev_desc[0].ChipID != NAND_ChipID_UNKNOWN) {
+		print_size(nand_dev_desc[0].totlen, "\n");
+	}
+}
+#endif

board/esd/hub405/u-boot.lds

@@ -0,0 +1,147 @@
+/*
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+/* Do we need any of these for elf?
+   __DYNAMIC = 0;    */
+SECTIONS
+{
+  .resetvec 0xFFFFFFFC :
+  {
+    *(.resetvec)
+  } = 0xffff
+
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)		}
+  .rela.text     : { *(.rela.text) 	}
+  .rel.data      : { *(.rel.data)		}
+  .rela.data     : { *(.rela.data) 	}
+  .rel.rodata    : { *(.rel.rodata) 	}
+  .rela.rodata   : { *(.rela.rodata) 	}
+  .rel.got       : { *(.rel.got)		}
+  .rela.got      : { *(.rela.got)		}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)		}
+  .rela.bss      : { *(.rela.bss)		}
+  .rel.plt       : { *(.rel.plt)		}
+  .rela.plt      : { *(.rela.plt)		}
+  .init          : { *(.init)	}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    /* WARNING - the following is hand-optimized to fit within	*/
+    /* the sector layout of our flash chips!	XXX FIXME XXX	*/
+
+    cpu/ppc4xx/start.o	(.text)
+    cpu/ppc4xx/traps.o	(.text)
+    cpu/ppc4xx/interrupts.o	(.text)
+    cpu/ppc4xx/serial.o	(.text)
+    cpu/ppc4xx/cpu_init.o	(.text)
+    cpu/ppc4xx/speed.o	(.text)
+    cpu/ppc4xx/405gp_enet.o	(.text)
+    common/dlmalloc.o	(.text)
+    lib_generic/crc32.o		(.text)
+    lib_ppc/extable.o	(.text)
+    lib_generic/zlib.o		(.text)
+
+/*    . = env_offset;*/
+/*    common/environment.o(.text)*/
+
+    *(.text)
+    *(.fixup)
+    *(.got1)
+  }
+  _etext = .;
+  PROVIDE (etext = .);
+  .rodata    :
+  {
+    *(.rodata)
+    *(.rodata1)
+    *(.rodata.str1.4)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x00FF) & 0xFFFFFF00;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
+  __fixup_entries = (. - _FIXUP_TABLE_)>>2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  __u_boot_cmd_start = .;
+  .u_boot_cmd : { *(.u_boot_cmd) }
+  __u_boot_cmd_end = .;
+
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(256);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(256);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+  _end = . ;
+  PROVIDE (end = .);
+}

board/esd/pci405/cmd_pci405.c

@@ -107,5 +107,10 @@ int do_loadpci(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 
 	return 0;
 }
+U_BOOT_CMD(
+	loadpci,	1,	1,	do_loadpci,
+	"loadpci - Wait for pci-image and boot it\n",
+	NULL
+);
 
 #endif

board/esd/plu405/Makefile

@@ -0,0 +1,46 @@
+#
+# (C) Copyright 2000
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	= $(BOARD).o flash.o
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) crv $@ $(OBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+sinclude .depend
+
+#########################################################################

board/esd/plu405/config.mk

@@ -0,0 +1,29 @@
+#
+# (C) Copyright 2000
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# esd PLU405 boards
+#
+
+TEXT_BASE = 0xFFFC0000
+#TEXT_BASE = 0x00FC0000

board/esd/plu405/flash.c

@@ -0,0 +1,101 @@
+/*
+ * (C) Copyright 2001
+ * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <ppc4xx.h>
+#include <asm/processor.h>
+
+/*
+ * include common flash code (for esd boards)
+ */
+#include "../common/flash.c"
+
+/*-----------------------------------------------------------------------
+ * Functions
+ */
+static ulong flash_get_size (vu_long * addr, flash_info_t * info);
+static void flash_get_offsets (ulong base, flash_info_t * info);
+
+/*-----------------------------------------------------------------------
+ */
+
+unsigned long flash_init (void)
+{
+	unsigned long size_b0;
+	int i;
+	uint pbcr;
+	unsigned long base_b0;
+	int size_val = 0;
+
+	/* Init: no FLASHes known */
+	for (i=0; i<CFG_MAX_FLASH_BANKS; ++i) {
+		flash_info[i].flash_id = FLASH_UNKNOWN;
+	}
+
+	/* Static FLASH Bank configuration here - FIXME XXX */
+
+	size_b0 = flash_get_size((vu_long *)FLASH_BASE0_PRELIM, &flash_info[0]);
+
+	if (flash_info[0].flash_id == FLASH_UNKNOWN) {
+		printf ("## Unknown FLASH on Bank 0 - Size = 0x%08lx = %ld MB\n",
+			size_b0, size_b0<<20);
+	}
+
+	/* Setup offsets */
+	flash_get_offsets (-size_b0, &flash_info[0]);
+
+	/* Re-do sizing to get full correct info */
+	mtdcr(ebccfga, pb0cr);
+	pbcr = mfdcr(ebccfgd);
+	mtdcr(ebccfga, pb0cr);
+	base_b0 = -size_b0;
+	switch (size_b0) {
+	case 1 << 20:
+		size_val = 0;
+		break;
+	case 2 << 20:
+		size_val = 1;
+		break;
+	case 4 << 20:
+		size_val = 2;
+		break;
+	case 8 << 20:
+		size_val = 3;
+		break;
+	case 16 << 20:
+		size_val = 4;
+		break;
+	}
+	pbcr = (pbcr & 0x0001ffff) | base_b0 | (size_val << 17);
+	mtdcr(ebccfgd, pbcr);
+
+	/* Monitor protection ON by default */
+	(void)flash_protect(FLAG_PROTECT_SET,
+			    -CFG_MONITOR_LEN,
+			    0xffffffff,
+			    &flash_info[0]);
+
+	flash_info[0].size = size_b0;
+
+	return (size_b0);
+}

board/esd/plu405/plu405.c

@@ -0,0 +1,268 @@
+/*
+ * (C) Copyright 2001-2003
+ * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/processor.h>
+#include <command.h>
+#include <malloc.h>
+
+/* ------------------------------------------------------------------------- */
+
+#if 0
+#define FPGA_DEBUG
+#endif
+
+extern int do_reset (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]);
+
+/* fpga configuration data - gzip compressed and generated by bin2c */
+const unsigned char fpgadata[] =
+{
+#include "fpgadata.c"
+};
+
+/*
+ * include common fpga code (for esd boards)
+ */
+#include "../common/fpga.c"
+
+
+/* Prototypes */
+int gunzip(void *, int, unsigned char *, int *);
+
+
+int board_pre_init (void)
+{
+	/*
+	 * IRQ 0-15  405GP internally generated; active high; level sensitive
+	 * IRQ 16    405GP internally generated; active low; level sensitive
+	 * IRQ 17-24 RESERVED
+	 * IRQ 25 (EXT IRQ 0) CAN0; active low; level sensitive
+	 * IRQ 26 (EXT IRQ 1) SER0 ; active low; level sensitive
+	 * IRQ 27 (EXT IRQ 2) SER1; active low; level sensitive
+	 * IRQ 28 (EXT IRQ 3) FPGA 0; active low; level sensitive
+	 * IRQ 29 (EXT IRQ 4) FPGA 1; active low; level sensitive
+	 * IRQ 30 (EXT IRQ 5) PCI INTA; active low; level sensitive
+	 * IRQ 31 (EXT IRQ 6) COMPACT FLASH; active high; level sensitive
+	 */
+	mtdcr(uicsr, 0xFFFFFFFF);       /* clear all ints */
+	mtdcr(uicer, 0x00000000);       /* disable all ints */
+	mtdcr(uiccr, 0x00000000);       /* set all to be non-critical*/
+	mtdcr(uicpr, 0xFFFFFF99);       /* set int polarities */
+	mtdcr(uictr, 0x10000000);       /* set int trigger levels */
+	mtdcr(uicvcr, 0x00000001);      /* set vect base=0,INT0 highest priority*/
+	mtdcr(uicsr, 0xFFFFFFFF);       /* clear all ints */
+
+	/*
+	 * EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 15 us
+	 */
+	mtebc (epcr, 0xa8400000); /* ebc always driven */
+
+	return 0;
+}
+
+
+/* ------------------------------------------------------------------------- */
+
+int misc_init_f (void)
+{
+	return 0;  /* dummy implementation */
+}
+
+
+int misc_init_r (void)
+{
+	volatile unsigned char *duart0_mcr = (unsigned char *)((ulong)DUART0_BA + 4);
+	volatile unsigned char *duart1_mcr = (unsigned char *)((ulong)DUART1_BA + 4);
+	unsigned char *dst;
+	ulong len = sizeof(fpgadata);
+	int status;
+	int index;
+	int i;
+
+#if 1 /* test-only */
+	dst = malloc(CFG_FPGA_MAX_SIZE);
+	if (gunzip (dst, CFG_FPGA_MAX_SIZE, (uchar *)fpgadata, (int *)&len) != 0) {
+		printf ("GUNZIP ERROR - must RESET board to recover\n");
+		do_reset (NULL, 0, 0, NULL);
+	}
+
+	status = fpga_boot(dst, len);
+	if (status != 0) {
+		printf("\nFPGA: Booting failed ");
+		switch (status) {
+		case ERROR_FPGA_PRG_INIT_LOW:
+			printf("(Timeout: INIT not low after asserting PROGRAM*)\n ");
+			break;
+		case ERROR_FPGA_PRG_INIT_HIGH:
+			printf("(Timeout: INIT not high after deasserting PROGRAM*)\n ");
+			break;
+		case ERROR_FPGA_PRG_DONE:
+			printf("(Timeout: DONE not high after programming FPGA)\n ");
+			break;
+		}
+
+		/* display infos on fpgaimage */
+		index = 15;
+		for (i=0; i<4; i++) {
+			len = dst[index];
+			printf("FPGA: %s\n", &(dst[index+1]));
+			index += len+3;
+		}
+		putc ('\n');
+		/* delayed reboot */
+		for (i=20; i>0; i--) {
+			printf("Rebooting in %2d seconds \r",i);
+			for (index=0;index<1000;index++)
+				udelay(1000);
+		}
+		putc ('\n');
+		do_reset(NULL, 0, 0, NULL);
+	}
+
+	puts("FPGA:  ");
+
+	/* display infos on fpgaimage */
+	index = 15;
+	for (i=0; i<4; i++) {
+		len = dst[index];
+		printf("%s ", &(dst[index+1]));
+		index += len+3;
+	}
+	putc ('\n');
+
+	free(dst);
+
+	/*
+	 * Reset FPGA via FPGA_DATA pin
+	 */
+	SET_FPGA(FPGA_PRG | FPGA_CLK);
+	udelay(1000); /* wait 1ms */
+	SET_FPGA(FPGA_PRG | FPGA_CLK | FPGA_DATA);
+	udelay(1000); /* wait 1ms */
+
+	/*
+	 * Reset external DUARTs
+	 */
+	out32(GPIO0_OR, in32(GPIO0_OR) | CFG_DUART_RST); /* set reset to high */
+	udelay(10); /* wait 10us */
+	out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_DUART_RST); /* set reset to low */
+	udelay(1000); /* wait 1ms */
+
+	/*
+	 * Set NAND-FLASH GPIO signals to default
+	 */
+	out32(GPIO0_OR, in32(GPIO0_OR) & ~(CFG_NAND_CLE | CFG_NAND_ALE));
+	out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);
+
+	/*
+	 * Enable interrupts in exar duart mcr[3]
+	 */
+	*duart0_mcr = 0x08;
+	*duart1_mcr = 0x08;
+#endif
+
+	return (0);
+}
+
+
+/*
+ * Check Board Identity:
+ */
+
+int checkboard (void)
+{
+	unsigned char str[64];
+	int i = getenv_r ("serial#", str, sizeof(str));
+
+	puts ("Board: ");
+
+	if (i == -1) {
+		puts ("### No HW ID - assuming PLU405");
+	} else {
+		puts(str);
+	}
+
+	putc ('\n');
+
+	return 0;
+}
+
+/* ------------------------------------------------------------------------- */
+
+long int initdram (int board_type)
+{
+	unsigned long val;
+
+	mtdcr(memcfga, mem_mb0cf);
+	val = mfdcr(memcfgd);
+
+#if 0
+	printf("\nmb0cf=%x\n", val); /* test-only */
+	printf("strap=%x\n", mfdcr(strap)); /* test-only */
+#endif
+
+	return (4*1024*1024 << ((val & 0x000e0000) >> 17));
+}
+
+/* ------------------------------------------------------------------------- */
+
+int testdram (void)
+{
+	/* TODO: XXX XXX XXX */
+	printf ("test: 16 MB - ok\n");
+
+	return (0);
+}
+
+/* ------------------------------------------------------------------------- */
+
+#ifdef CONFIG_IDE_RESET
+void ide_set_reset(int on)
+{
+	volatile unsigned short *fpga_mode =
+		(unsigned short *)((ulong)CFG_FPGA_BASE_ADDR + CFG_FPGA_CTRL);
+
+	/*
+	 * Assert or deassert CompactFlash Reset Pin
+	 */
+	if (on) {		/* assert RESET */
+		*fpga_mode &= ~(CFG_FPGA_CTRL_CF_RESET);
+	} else {		/* release RESET */
+		*fpga_mode |= CFG_FPGA_CTRL_CF_RESET;
+	}
+}
+#endif /* CONFIG_IDE_RESET */
+
+
+#if (CONFIG_COMMANDS & CFG_CMD_NAND)
+#include <linux/mtd/nand.h>
+extern struct nand_chip nand_dev_desc[CFG_MAX_NAND_DEVICE];
+
+void nand_init(void)
+{
+	nand_probe(CFG_NAND_BASE);
+	if (nand_dev_desc[0].ChipID != NAND_ChipID_UNKNOWN) {
+		print_size(nand_dev_desc[0].totlen, "\n");
+	}
+}
+#endif

board/esd/plu405/u-boot.lds

@@ -0,0 +1,148 @@
+/*
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+/* Do we need any of these for elf?
+   __DYNAMIC = 0;    */
+SECTIONS
+{
+  .resetvec 0xFFFFFFFC :
+  {
+    *(.resetvec)
+  } = 0xffff
+
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)		}
+  .rela.text     : { *(.rela.text) 	}
+  .rel.data      : { *(.rel.data)		}
+  .rela.data     : { *(.rela.data) 	}
+  .rel.rodata    : { *(.rel.rodata) 	}
+  .rela.rodata   : { *(.rela.rodata) 	}
+  .rel.got       : { *(.rel.got)		}
+  .rela.got      : { *(.rela.got)		}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)		}
+  .rela.bss      : { *(.rela.bss)		}
+  .rel.plt       : { *(.rel.plt)		}
+  .rela.plt      : { *(.rela.plt)		}
+  .init          : { *(.init)	}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    /* WARNING - the following is hand-optimized to fit within	*/
+    /* the sector layout of our flash chips!	XXX FIXME XXX	*/
+
+    cpu/ppc4xx/start.o	(.text)
+    cpu/ppc4xx/traps.o	(.text)
+    cpu/ppc4xx/interrupts.o	(.text)
+    cpu/ppc4xx/serial.o	(.text)
+    cpu/ppc4xx/cpu_init.o	(.text)
+    cpu/ppc4xx/speed.o	(.text)
+    cpu/ppc4xx/405gp_enet.o	(.text)
+    common/dlmalloc.o	(.text)
+    lib_generic/crc32.o		(.text)
+    lib_ppc/extable.o	(.text)
+    lib_generic/zlib.o		(.text)
+
+/*    . = env_offset;*/
+/*    common/environment.o(.text)*/
+
+    *(.text)
+    *(.fixup)
+    *(.got1)
+  }
+  _etext = .;
+  PROVIDE (etext = .);
+  .rodata    :
+  {
+    *(.rodata)
+    *(.rodata1)
+    *(.rodata.str1.4)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x00FF) & 0xFFFFFF00;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
+  __fixup_entries = (. - _FIXUP_TABLE_)>>2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  __u_boot_cmd_start = .;
+  .u_boot_cmd : { *(.u_boot_cmd) }
+  __u_boot_cmd_end = .;
+
+
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(256);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(256);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+  _end = . ;
+  PROVIDE (end = .);
+}

board/esd/pmc405/Makefile

@@ -25,7 +25,12 @@ include $(TOPDIR)/config.mk
 
 LIB	= lib$(BOARD).a
 
-OBJS	= $(BOARD).o strataflash.o
+# Objects for Xilinx JTAG programming (CPLD)
+CPLD    = ../common/xilinx_jtag/lenval.o \
+	  ../common/xilinx_jtag/micro.o \
+	  ../common/xilinx_jtag/ports.o
+
+OBJS	= $(BOARD).o strataflash.o $(CPLD)
 
 $(LIB):	$(OBJS) $(SOBJS)
 	$(AR) crv $@ $(OBJS)

board/esd/pmc405/pmc405.c

@@ -26,11 +26,13 @@
 #include <command.h>
 #include <malloc.h>
 
-/* ------------------------------------------------------------------------- */
 
-
-/* Prototypes */
-int gunzip(void *, int, unsigned char *, int *);
+/* fpga configuration data - not compressed, generated by bin2c */
+const unsigned char fpgadata[] =
+{
+#include "fpgadata.c"
+};
+int filesize = sizeof(fpgadata);
 
 
 int board_pre_init (void)
@@ -74,104 +76,6 @@ int misc_init_f (void)
 
 int misc_init_r (void)
 {
-#if 0 /* test-only */
-	DECLARE_GLOBAL_DATA_PTR;
-	volatile unsigned short *fpga_mode =
-		(unsigned short *)((ulong)CFG_FPGA_BASE_ADDR + CFG_FPGA_CTRL);
-	volatile unsigned char *duart0_mcr =
-		(unsigned char *)((ulong)DUART0_BA + 4);
-	volatile unsigned char *duart1_mcr =
-		(unsigned char *)((ulong)DUART1_BA + 4);
-	bd_t *bd = gd->bd;
-	char *	tmp;                    /* Temporary char pointer      */
-	unsigned char *dst;
-	ulong len = sizeof(fpgadata);
-	int status;
-	int index;
-	int i;
-	unsigned long cntrl0Reg;
-
-	/*
-	 * Setup GPIO pins (CS6+CS7 as GPIO)
-	 */
-	cntrl0Reg = mfdcr(cntrl0);
-	mtdcr(cntrl0, cntrl0Reg | 0x00300000);
-
-	dst = malloc(CFG_FPGA_MAX_SIZE);
-	if (gunzip (dst, CFG_FPGA_MAX_SIZE, (uchar *)fpgadata, (int *)&len) != 0) {
-		printf ("GUNZIP ERROR - must RESET board to recover\n");
-		do_reset (NULL, 0, 0, NULL);
-	}
-
-	status = fpga_boot(dst, len);
-	if (status != 0) {
-		printf("\nFPGA: Booting failed ");
-		switch (status) {
-		case ERROR_FPGA_PRG_INIT_LOW:
-			printf("(Timeout: INIT not low after asserting PROGRAM*)\n ");
-			break;
-		case ERROR_FPGA_PRG_INIT_HIGH:
-			printf("(Timeout: INIT not high after deasserting PROGRAM*)\n ");
-			break;
-		case ERROR_FPGA_PRG_DONE:
-			printf("(Timeout: DONE not high after programming FPGA)\n ");
-			break;
-		}
-
-		/* display infos on fpgaimage */
-		index = 15;
-		for (i=0; i<4; i++) {
-			len = dst[index];
-			printf("FPGA: %s\n", &(dst[index+1]));
-			index += len+3;
-		}
-		putc ('\n');
-		/* delayed reboot */
-		for (i=20; i>0; i--) {
-			printf("Rebooting in %2d seconds \r",i);
-			for (index=0;index<1000;index++)
-				udelay(1000);
-		}
-		putc ('\n');
-		do_reset(NULL, 0, 0, NULL);
-	}
-
-	/* restore gpio/cs settings */
-	mtdcr(cntrl0, cntrl0Reg);
-
-	puts("FPGA:  ");
-
-	/* display infos on fpgaimage */
-	index = 15;
-	for (i=0; i<4; i++) {
-		len = dst[index];
-		printf("%s ", &(dst[index+1]));
-		index += len+3;
-	}
-	putc ('\n');
-
-	free(dst);
-
-	/*
-	 * Reset FPGA via FPGA_DATA pin
-	 */
-	SET_FPGA(FPGA_PRG | FPGA_CLK);
-	udelay(1000); /* wait 1ms */
-	SET_FPGA(FPGA_PRG | FPGA_CLK | FPGA_DATA);
-	udelay(1000); /* wait 1ms */
-
-	/*
-	 * Enable power on PS/2 interface
-	 */
-	*fpga_mode |= CFG_FPGA_CTRL_PS2_RESET;
-
-	/*
-	 * Enable interrupts in exar duart mcr[3]
-	 */
-	*duart0_mcr = 0x08;
-	*duart1_mcr = 0x08;
-#endif
-
 	return (0);
 }
 
@@ -188,7 +92,7 @@ int checkboard (void)
 	puts ("Board: ");
 
 	if (i == -1) {
-		puts ("### No HW ID - assuming ABG405");
+		puts ("### No HW ID - assuming PMC405");
 	} else {
 		puts(str);
 	}

board/esd/voh405/Makefile

@@ -0,0 +1,46 @@
+#
+# (C) Copyright 2000
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	= $(BOARD).o flash.o
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) crv $@ $(OBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+sinclude .depend
+
+#########################################################################

board/esd/voh405/config.mk

@@ -0,0 +1,29 @@
+#
+# (C) Copyright 2000
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# esd VOH405 boards
+#
+
+TEXT_BASE = 0xFFFC0000
+#TEXT_BASE = 0x00FC0000

board/esd/voh405/flash.c

@@ -0,0 +1,101 @@
+/*
+ * (C) Copyright 2001
+ * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <ppc4xx.h>
+#include <asm/processor.h>
+
+/*
+ * include common flash code (for esd boards)
+ */
+#include "../common/flash.c"
+
+/*-----------------------------------------------------------------------
+ * Functions
+ */
+static ulong flash_get_size (vu_long * addr, flash_info_t * info);
+static void flash_get_offsets (ulong base, flash_info_t * info);
+
+/*-----------------------------------------------------------------------
+ */
+
+unsigned long flash_init (void)
+{
+	unsigned long size_b0;
+	int i;
+	uint pbcr;
+	unsigned long base_b0;
+	int size_val = 0;
+
+	/* Init: no FLASHes known */
+	for (i=0; i<CFG_MAX_FLASH_BANKS; ++i) {
+		flash_info[i].flash_id = FLASH_UNKNOWN;
+	}
+
+	/* Static FLASH Bank configuration here - FIXME XXX */
+
+	size_b0 = flash_get_size((vu_long *)FLASH_BASE0_PRELIM, &flash_info[0]);
+
+	if (flash_info[0].flash_id == FLASH_UNKNOWN) {
+		printf ("## Unknown FLASH on Bank 0 - Size = 0x%08lx = %ld MB\n",
+			size_b0, size_b0<<20);
+	}
+
+	/* Setup offsets */
+	flash_get_offsets (-size_b0, &flash_info[0]);
+
+	/* Re-do sizing to get full correct info */
+	mtdcr(ebccfga, pb0cr);
+	pbcr = mfdcr(ebccfgd);
+	mtdcr(ebccfga, pb0cr);
+	base_b0 = -size_b0;
+	switch (size_b0) {
+	case 1 << 20:
+		size_val = 0;
+		break;
+	case 2 << 20:
+		size_val = 1;
+		break;
+	case 4 << 20:
+		size_val = 2;
+		break;
+	case 8 << 20:
+		size_val = 3;
+		break;
+	case 16 << 20:
+		size_val = 4;
+		break;
+	}
+	pbcr = (pbcr & 0x0001ffff) | base_b0 | (size_val << 17);
+	mtdcr(ebccfgd, pbcr);
+
+	/* Monitor protection ON by default */
+	(void)flash_protect(FLAG_PROTECT_SET,
+			    -CFG_MONITOR_LEN,
+			    0xffffffff,
+			    &flash_info[0]);
+
+	flash_info[0].size = size_b0;
+
+	return (size_b0);
+}

board/esd/voh405/u-boot.lds

@@ -0,0 +1,148 @@
+/*
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+/* Do we need any of these for elf?
+   __DYNAMIC = 0;    */
+SECTIONS
+{
+  .resetvec 0xFFFFFFFC :
+  {
+    *(.resetvec)
+  } = 0xffff
+
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)		}
+  .rela.text     : { *(.rela.text) 	}
+  .rel.data      : { *(.rel.data)		}
+  .rela.data     : { *(.rela.data) 	}
+  .rel.rodata    : { *(.rel.rodata) 	}
+  .rela.rodata   : { *(.rela.rodata) 	}
+  .rel.got       : { *(.rel.got)		}
+  .rela.got      : { *(.rela.got)		}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)		}
+  .rela.bss      : { *(.rela.bss)		}
+  .rel.plt       : { *(.rel.plt)		}
+  .rela.plt      : { *(.rela.plt)		}
+  .init          : { *(.init)	}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    /* WARNING - the following is hand-optimized to fit within	*/
+    /* the sector layout of our flash chips!	XXX FIXME XXX	*/
+
+    cpu/ppc4xx/start.o	(.text)
+    cpu/ppc4xx/traps.o	(.text)
+    cpu/ppc4xx/interrupts.o	(.text)
+    cpu/ppc4xx/serial.o	(.text)
+    cpu/ppc4xx/cpu_init.o	(.text)
+    cpu/ppc4xx/speed.o	(.text)
+    cpu/ppc4xx/405gp_enet.o	(.text)
+    common/dlmalloc.o	(.text)
+    lib_generic/crc32.o		(.text)
+    lib_ppc/extable.o	(.text)
+    lib_generic/zlib.o		(.text)
+
+/*    . = env_offset;*/
+/*    common/environment.o(.text)*/
+
+    *(.text)
+    *(.fixup)
+    *(.got1)
+  }
+  _etext = .;
+  PROVIDE (etext = .);
+  .rodata    :
+  {
+    *(.rodata)
+    *(.rodata1)
+    *(.rodata.str1.4)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x00FF) & 0xFFFFFF00;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
+  __fixup_entries = (. - _FIXUP_TABLE_)>>2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  __u_boot_cmd_start = .;
+  .u_boot_cmd : { *(.u_boot_cmd) }
+  __u_boot_cmd_end = .;
+
+
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(256);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(256);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+  _end = . ;
+  PROVIDE (end = .);
+}

board/esd/voh405/voh405.c

@@ -0,0 +1,273 @@
+/*
+ * (C) Copyright 2001-2003
+ * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/processor.h>
+#include <command.h>
+#include <malloc.h>
+
+/* ------------------------------------------------------------------------- */
+
+#if 0
+#define FPGA_DEBUG
+#endif
+
+extern int do_reset (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]);
+
+/* fpga configuration data - gzip compressed and generated by bin2c */
+const unsigned char fpgadata[] =
+{
+#include "fpgadata.c"
+};
+
+/*
+ * include common fpga code (for esd boards)
+ */
+#include "../common/fpga.c"
+
+
+/* Prototypes */
+int gunzip(void *, int, unsigned char *, int *);
+
+
+int board_pre_init (void)
+{
+	/*
+	 * IRQ 0-15  405GP internally generated; active high; level sensitive
+	 * IRQ 16    405GP internally generated; active low; level sensitive
+	 * IRQ 17-24 RESERVED
+	 * IRQ 25 (EXT IRQ 0) CAN0; active low; level sensitive
+	 * IRQ 26 (EXT IRQ 1) SER0 ; active low; level sensitive
+	 * IRQ 27 (EXT IRQ 2) SER1; active low; level sensitive
+	 * IRQ 28 (EXT IRQ 3) FPGA 0; active low; level sensitive
+	 * IRQ 29 (EXT IRQ 4) FPGA 1; active low; level sensitive
+	 * IRQ 30 (EXT IRQ 5) PCI INTA; active low; level sensitive
+	 * IRQ 31 (EXT IRQ 6) COMPACT FLASH; active high; level sensitive
+	 */
+	mtdcr(uicsr, 0xFFFFFFFF);       /* clear all ints */
+	mtdcr(uicer, 0x00000000);       /* disable all ints */
+	mtdcr(uiccr, 0x00000000);       /* set all to be non-critical*/
+	mtdcr(uicpr, 0xFFFFFFB5);       /* set int polarities */
+	mtdcr(uictr, 0x10000000);       /* set int trigger levels */
+	mtdcr(uicvcr, 0x00000001);      /* set vect base=0,INT0 highest priority*/
+	mtdcr(uicsr, 0xFFFFFFFF);       /* clear all ints */
+
+	/*
+	 * EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 15 us
+	 */
+	mtebc (epcr, 0xa8400000); /* ebc always driven */
+
+	return 0;
+}
+
+
+/* ------------------------------------------------------------------------- */
+
+int misc_init_f (void)
+{
+	return 0;  /* dummy implementation */
+}
+
+
+int misc_init_r (void)
+{
+	volatile unsigned char *duart0_mcr = (unsigned char *)((ulong)DUART0_BA + 4);
+	volatile unsigned char *duart1_mcr = (unsigned char *)((ulong)DUART1_BA + 4);
+	volatile unsigned short *lcd_reg =
+		(unsigned short *)((ulong)CFG_FPGA_BASE_ADDR + CFG_FPGA_CTRL + 4);
+	unsigned char *dst;
+	ulong len = sizeof(fpgadata);
+	int status;
+	int index;
+	int i;
+
+	dst = malloc(CFG_FPGA_MAX_SIZE);
+	if (gunzip (dst, CFG_FPGA_MAX_SIZE, (uchar *)fpgadata, (int *)&len) != 0) {
+		printf ("GUNZIP ERROR - must RESET board to recover\n");
+		do_reset (NULL, 0, 0, NULL);
+	}
+
+	status = fpga_boot(dst, len);
+	if (status != 0) {
+		printf("\nFPGA: Booting failed ");
+		switch (status) {
+		case ERROR_FPGA_PRG_INIT_LOW:
+			printf("(Timeout: INIT not low after asserting PROGRAM*)\n ");
+			break;
+		case ERROR_FPGA_PRG_INIT_HIGH:
+			printf("(Timeout: INIT not high after deasserting PROGRAM*)\n ");
+			break;
+		case ERROR_FPGA_PRG_DONE:
+			printf("(Timeout: DONE not high after programming FPGA)\n ");
+			break;
+		}
+
+		/* display infos on fpgaimage */
+		index = 15;
+		for (i=0; i<4; i++) {
+			len = dst[index];
+			printf("FPGA: %s\n", &(dst[index+1]));
+			index += len+3;
+		}
+		putc ('\n');
+		/* delayed reboot */
+		for (i=20; i>0; i--) {
+			printf("Rebooting in %2d seconds \r",i);
+			for (index=0;index<1000;index++)
+				udelay(1000);
+		}
+		putc ('\n');
+		do_reset(NULL, 0, 0, NULL);
+	}
+
+	puts("FPGA:  ");
+
+	/* display infos on fpgaimage */
+	index = 15;
+	for (i=0; i<4; i++) {
+		len = dst[index];
+		printf("%s ", &(dst[index+1]));
+		index += len+3;
+	}
+	putc ('\n');
+
+	free(dst);
+
+	/*
+	 * Reset FPGA via FPGA_DATA pin
+	 */
+	SET_FPGA(FPGA_PRG | FPGA_CLK);
+	udelay(1000); /* wait 1ms */
+	SET_FPGA(FPGA_PRG | FPGA_CLK | FPGA_DATA);
+	udelay(1000); /* wait 1ms */
+
+	/*
+	 * Reset external DUARTs
+	 */
+	out32(GPIO0_OR, in32(GPIO0_OR) | CFG_DUART_RST); /* set reset to high */
+	udelay(10); /* wait 10us */
+	out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_DUART_RST); /* set reset to low */
+	udelay(1000); /* wait 1ms */
+
+	/*
+	 * Set NAND-FLASH GPIO signals to default
+	 */
+	out32(GPIO0_OR, in32(GPIO0_OR) & ~(CFG_NAND_CLE | CFG_NAND_ALE));
+	out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);
+
+	/*
+	 * Enable interrupts in exar duart mcr[3]
+	 */
+	*duart0_mcr = 0x08;
+	*duart1_mcr = 0x08;
+
+	/*
+	 * Set default contrast voltage on epson vga controller
+	 */
+	*lcd_reg = 0x4848;
+
+	return (0);
+}
+
+
+/*
+ * Check Board Identity:
+ */
+
+int checkboard (void)
+{
+	unsigned char str[64];
+	int i = getenv_r ("serial#", str, sizeof(str));
+
+	puts ("Board: ");
+
+	if (i == -1) {
+		puts ("### No HW ID - assuming VOH405");
+	} else {
+		puts(str);
+	}
+
+	putc ('\n');
+
+	return 0;
+}
+
+/* ------------------------------------------------------------------------- */
+
+long int initdram (int board_type)
+{
+	unsigned long val;
+
+	mtdcr(memcfga, mem_mb0cf);
+	val = mfdcr(memcfgd);
+
+#if 0
+	printf("\nmb0cf=%x\n", val); /* test-only */
+	printf("strap=%x\n", mfdcr(strap)); /* test-only */
+#endif
+
+	return (4*1024*1024 << ((val & 0x000e0000) >> 17));
+}
+
+/* ------------------------------------------------------------------------- */
+
+int testdram (void)
+{
+	/* TODO: XXX XXX XXX */
+	printf ("test: 16 MB - ok\n");
+
+	return (0);
+}
+
+/* ------------------------------------------------------------------------- */
+
+#ifdef CONFIG_IDE_RESET
+void ide_set_reset(int on)
+{
+	volatile unsigned short *fpga_mode =
+		(unsigned short *)((ulong)CFG_FPGA_BASE_ADDR + CFG_FPGA_CTRL);
+
+	/*
+	 * Assert or deassert CompactFlash Reset Pin
+	 */
+	if (on) {		/* assert RESET */
+		*fpga_mode &= ~(CFG_FPGA_CTRL_CF_RESET);
+	} else {		/* release RESET */
+		*fpga_mode |= CFG_FPGA_CTRL_CF_RESET;
+	}
+}
+#endif /* CONFIG_IDE_RESET */
+
+
+#if (CONFIG_COMMANDS & CFG_CMD_NAND)
+#include <linux/mtd/nand.h>
+extern struct nand_chip nand_dev_desc[CFG_MAX_NAND_DEVICE];
+
+void nand_init(void)
+{
+	nand_probe(CFG_NAND_BASE);
+	if (nand_dev_desc[0].ChipID != NAND_ChipID_UNKNOWN) {
+		print_size(nand_dev_desc[0].totlen, "\n");
+	}
+}
+#endif

board/trab/Makefile

@@ -28,9 +28,27 @@ LIB	= lib$(BOARD).a
 OBJS	:= trab.o flash.o vfd.o cmd_trab.o memory.o tsc2000.o
 SOBJS	:= memsetup.o
 
+gcclibdir := $(shell dirname `$(CC) -print-libgcc-file-name`)
+
+LOAD_ADDR = 0xc100000
+
+#########################################################################
+
+all:	$(LIB) trab_fkt.srec trab_fkt.bin
+
 $(LIB):	$(OBJS) $(SOBJS)
 	$(AR) crv $@ $(OBJS) $(SOBJS)
 
+trab_fkt.srec:	trab_fkt.o rs485.o tsc2000.o $(LIB)
+	$(LD) -g -Ttext $(LOAD_ADDR) -o $(<:.o=) -e $(<:.o=) $^ $(LIB) \
+		-L../../examples -lstubs \
+		-L../../lib_generic -lgeneric \
+		-L$(gcclibdir) -lgcc
+	$(OBJCOPY) -O srec $(<:.o=) $@
+
+trab_fkt.bin:	trab_fkt.srec
+	$(OBJCOPY) -O binary $< $@ 2>/dev/null
+
 clean:
 	rm -f $(SOBJS) $(OBJS)
 

board/trab/rs485.c

@@ -0,0 +1,203 @@
+/*
+ * (C) Copyright 2003
+ * Martin Krause, TQ-Systems GmbH, <martin.krause@tqs.de>
+ *
+ * Based on cpu/arm920t/serial.c, by Gary Jennejohn
+ * (C) Copyright 2002 Gary Jennejohn, DENX Software Engineering, <gj@denx.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ *
+ */
+
+#include <common.h>
+#include <s3c2400.h>
+#include "rs485.h"
+
+static void rs485_setbrg (void);
+static void rs485_cfgio (void);
+static void set_rs485re(unsigned char rs485re_state);
+static void set_rs485de(unsigned char rs485de_state);
+static void rs485_setbrg (void);
+#ifdef	NOT_USED
+static void trab_rs485_disable_tx(void);
+static void trab_rs485_disable_rx(void);
+#endif
+
+#define UART_NR	S3C24X0_UART1
+
+/* CPLD-Register for controlling TRAB hardware functions */
+#define CPLD_RS485_RE           ((volatile unsigned long *)0x04028000)
+
+static void rs485_setbrg (void)
+{
+	S3C24X0_UART * const uart = S3C24X0_GetBase_UART(UART_NR);
+	int i;
+	unsigned int reg = 0;
+
+	/* value is calculated so : (int)(PCLK/16./baudrate) -1 */
+        /* reg = (33000000 / (16 * gd->baudrate)) - 1; */
+        reg = (33000000 / (16 * 38.400)) - 1;
+
+	/* FIFO enable, Tx/Rx FIFO clear */
+	uart->UFCON = 0x07;
+	uart->UMCON = 0x0;
+	/* Normal,No parity,1 stop,8 bit */
+	uart->ULCON = 0x3;
+	/*
+	 * tx=level,rx=edge,disable timeout int.,enable rx error int.,
+	 * normal,interrupt or polling
+	 */
+	uart->UCON = 0x245;
+	uart->UBRDIV = reg;
+
+	for (i = 0; i < 100; i++);
+}
+
+static void rs485_cfgio (void)
+{
+        S3C24X0_GPIO * const gpio = S3C24X0_GetBase_GPIO();
+
+        gpio->PFCON &= ~(0x3 << 2);
+        gpio->PFCON |=  (0x2 << 2); /* configure GPF1 as RXD1 */
+
+        gpio->PFCON &= ~(0x3 << 6);
+        gpio->PFCON |=  (0x2 << 6); /* configure GPF3 as TXD1 */
+
+        gpio->PFUP |= (1 << 1); /* disable pullup on GPF1 */
+        gpio->PFUP |= (1 << 3); /* disable pullup on GPF3 */
+
+        gpio->PACON &= ~(1 << 11); /* set GPA11 (RS485_DE) to output */
+}
+
+/*
+ * Initialise the rs485 port with the given baudrate. The settings
+ * are always 8 data bits, no parity, 1 stop bit, no start bits.
+ *
+ */
+int rs485_init (void)
+{
+        rs485_cfgio ();
+        rs485_setbrg ();
+
+	return (0);
+}
+
+/*
+ * Read a single byte from the rs485 port. Returns 1 on success, 0
+ * otherwise. When the function is succesfull, the character read is
+ * written into its argument c.
+ */
+int rs485_getc (void)
+{
+	S3C24X0_UART * const uart = S3C24X0_GetBase_UART(UART_NR);
+
+	/* wait for character to arrive */
+	while (!(uart->UTRSTAT & 0x1));
+
+	return uart->URXH & 0xff;
+}
+
+/*
+ * Output a single byte to the rs485 port.
+ */
+void rs485_putc (const char c)
+{
+	S3C24X0_UART * const uart = S3C24X0_GetBase_UART(UART_NR);
+
+	/* wait for room in the tx FIFO */
+	while (!(uart->UTRSTAT & 0x2));
+
+	uart->UTXH = c;
+
+	/* If \n, also do \r */
+	if (c == '\n')
+		rs485_putc ('\r');
+}
+
+/*
+ * Test whether a character is in the RX buffer
+ */
+int rs485_tstc (void)
+{
+	S3C24X0_UART * const uart = S3C24X0_GetBase_UART(UART_NR);
+
+	return uart->UTRSTAT & 0x1;
+}
+
+void rs485_puts (const char *s)
+{
+	while (*s) {
+		rs485_putc (*s++);
+	}
+}
+
+
+/*
+ * State table:
+ *	RE	DE	Result
+ *	1	1	XMIT
+ *	0	0	RCV
+ *	1	0	Shutdown
+ */
+
+/* function that controls the receiver enable for the rs485 */
+/* rs485re_state reflects the level (0/1) of the RE pin */
+
+static void set_rs485re(unsigned char rs485re_state)
+{
+	if(rs485re_state)
+		*CPLD_RS485_RE = 0x010000;
+	else
+		*CPLD_RS485_RE = 0x0;
+}
+
+/* function that controls the sender enable for the rs485 */
+/* rs485de_state reflects the level (0/1) of the DE pin */
+
+static void set_rs485de(unsigned char rs485de_state)
+{
+        S3C24X0_GPIO * const gpio = S3C24X0_GetBase_GPIO();
+
+        /* This is on PORT A bit 11 */
+        if(rs485de_state)
+                gpio->PADAT |= (1 << 11);
+        else
+                gpio->PADAT &= ~(1 << 11);
+}
+
+
+void trab_rs485_enable_tx(void)
+{
+	set_rs485de(1);
+	set_rs485re(1);
+}
+
+void trab_rs485_enable_rx(void)
+{
+	set_rs485re(0);
+	set_rs485de(0);
+}
+
+#ifdef	NOT_USED
+static void trab_rs485_disable_tx(void)
+{
+	set_rs485de(0);
+}
+
+static void trab_rs485_disable_rx(void)
+{
+	set_rs485re(1);
+}
+#endif

board/trab/rs485.h

@@ -0,0 +1,37 @@
+/*
+ * (C) Copyright 2003
+ * Martin Krause, TQ-Systems GmbH, <martin.krause@tqs.de>
+ *
+ * Based on cpu/arm920t/serial.c, by Gary Jennejohn
+ * (C) Copyright 2002 Gary Jennejohn, DENX Software Engineering, <gj@denx.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ *
+ */
+
+#ifndef _RS485_H_
+#define _RS485_H_
+
+#include <s3c2400.h>
+
+int rs485_init (void);
+int rs485_getc (void);
+void rs485_putc (const char c);
+int rs485_tstc (void);
+void rs485_puts (const char *s);
+void trab_rs485_enable_tx(void);
+void trab_rs485_enable_rx(void);
+
+#endif	/* _RS485_H_ */

board/trab/tsc2000.c

@@ -29,6 +29,8 @@
 #include <s3c2400.h>
 #include "tsc2000.h"
 
+#include "Pt1000_temp_data.h"
+
 void spi_init(void)
 {
 	S3C24X0_GPIO * const gpio = S3C24X0_GetBase_GPIO();
@@ -56,7 +58,7 @@ void spi_init(void)
 }
 
 
-static void spi_wait_transmit_done(void)
+void spi_wait_transmit_done(void)
 {
 	S3C24X0_SPI * const spi = S3C24X0_GetBase_SPI();
 
@@ -64,7 +66,7 @@ static void spi_wait_transmit_done(void)
 }
 
 
-static void tsc2000_write(unsigned short reg, unsigned short data)
+void tsc2000_write(unsigned short reg, unsigned short data)
 {
 	S3C24X0_SPI * const spi = S3C24X0_GetBase_SPI();
 	unsigned int command;
@@ -84,7 +86,7 @@ static void tsc2000_write(unsigned short reg, unsigned short data)
 }
 
 
-static unsigned short tsc2000_read (unsigned short reg)
+unsigned short tsc2000_read (unsigned short reg)
 {
 	unsigned short command, data;
 	S3C24X0_SPI * const spi = S3C24X0_GetBase_SPI();
@@ -108,7 +110,7 @@ static unsigned short tsc2000_read (unsigned short reg)
 }
 
 
-static void tsc2000_set_mux (unsigned int channel)
+void tsc2000_set_mux (unsigned int channel)
 {
         S3C24X0_GPIO * const gpio = S3C24X0_GetBase_GPIO();
 
@@ -185,7 +187,7 @@ static void tsc2000_set_mux (unsigned int channel)
 }
 
 
-static void tsc2000_set_range (unsigned int range)
+void tsc2000_set_range (unsigned int range)
 {
         S3C24X0_GPIO * const gpio = S3C24X0_GetBase_GPIO();
 
@@ -206,7 +208,7 @@ static void tsc2000_set_range (unsigned int range)
 }
 
 
-static u16 tsc2000_read_channel (unsigned int channel)
+u16 tsc2000_read_channel (unsigned int channel)
 {
 	u16 res;
 
@@ -284,7 +286,7 @@ void tsc2000_reg_init (void)
 }
 
 
-static int tsc2000_interpolate(long value, long data[][2], long *result)
+int tsc2000_interpolate(long value, long data[][2], long *result)
 {
 	int i;
 
@@ -311,7 +313,7 @@ static int tsc2000_interpolate(long value, long data[][2], long *result)
 }
 
 
-static void adc_wait_conversion_done(void)
+void adc_wait_conversion_done(void)
 {
         while (!(tsc2000_read(TSC2000_REG_ADC) & (1 << 14)));
 }

board/trab/tsc2000.h

@@ -28,8 +28,6 @@
 #ifndef _TSC2000_H_
 #define _TSC2000_H_
 
-#include "Pt1000_temp_data.h"
-
 /* temperature channel multiplexer definitions */
 #define CON_MUX0         	(gpio->PCCON = (gpio->PCCON & 0x0FFFFFCFF) | 0x00000100)
 #define CLR_MUX0         	(gpio->PCDAT &= 0x0FFEF)
@@ -116,17 +114,17 @@
 #define ERROR_BATTERY   220     /* must be adjusted, if R68 is changed on
                                  * TRAB */
 
-static void tsc2000_write(unsigned short, unsigned short);
-static unsigned short tsc2000_read (unsigned short);
-static u16 tsc2000_read_channel (unsigned int);
-static void tsc2000_set_mux (unsigned int);
-static void tsc2000_set_range (unsigned int);
+void tsc2000_write(unsigned short, unsigned short);
+unsigned short tsc2000_read (unsigned short);
+u16 tsc2000_read_channel (unsigned int);
+void tsc2000_set_mux (unsigned int);
+void tsc2000_set_range (unsigned int);
 void tsc2000_reg_init (void);
 s32 tsc2000_contact_temp (void);
-static void spi_wait_transmit_done (void);
+void spi_wait_transmit_done (void);
 void spi_init(void);
-static int tsc2000_interpolate(long value, long data[][2], long *result);
-static void adc_wait_conversion_done(void);
+int tsc2000_interpolate(long value, long data[][2], long *result);
+void adc_wait_conversion_done(void);
 
 
 static inline void SET_CS_TOUCH(void)

cpu/ppc4xx/405gp_pci.c

@@ -266,6 +266,10 @@ void pci_405gp_init(struct pci_controller *hose)
 	}
 #endif
 
+#if defined(CONFIG_405EP) /* on ppc405ep vendor id is not set */
+	pci_write_config_word(PCIDEVID_405GP, PCI_VENDOR_ID, 0x1014); /* IBM */
+#endif
+
 	/*
 	 * Set HCE bit (Host Configuration Enabled)
 	 */

cpu/ppc4xx/sdram.c

@@ -80,6 +80,11 @@ void sdram_init(void)
 		rtr = 0x05f00000;
 	}
 
+	/*
+	 * Disable memory controller.
+	 */
+	mtsdram0(mem_mcopt1, 0x00000000);
+
 	/*
 	 * Set MB0CF for bank 0. (0-128MB) Address Mode 3 since 13x10(4)
 	 */

examples/Makefile

@@ -69,11 +69,6 @@ ifeq ($(BOARD),oxc)
 SREC   += eepro100_eeprom.srec
 endif
 
-##ifeq ($(BOARD),trab)
-##SREC   += trab_fkt.srec
-##BIN    += trab_fkt.bin
-##endif
-
 OBJS	= $(SREC:.srec=.o)
 
 LIB	= libstubs.a

include/_exports.h

@@ -10,6 +10,8 @@ EXPORT_FUNC(malloc)
 EXPORT_FUNC(free)
 EXPORT_FUNC(udelay)
 EXPORT_FUNC(get_timer)
+EXPORT_FUNC(vprintf)
+EXPORT_FUNC(do_reset)
 #if (CONFIG_COMMANDS & CFG_CMD_I2C)
 EXPORT_FUNC(i2c_write)
 EXPORT_FUNC(i2c_read)

include/configs/CPCI405AB.h

@@ -57,7 +57,7 @@
 #undef	CONFIG_BOOTARGS
 #define CONFIG_BOOTCOMMAND	"bootm 100000"	/* default boot command	*/
 
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
+#undef  CONFIG_LOADS_ECHO		/* echo on for serial download	*/
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
 #define CONFIG_MII		1	/* MII PHY management		*/
@@ -228,44 +228,34 @@
 #define CFG_JFFS2_FIRST_BANK    0           /* use for JFFS2 */
 #define CFG_JFFS2_NUM_BANKS     1           /* ! second bank contains U-Boot */
 
-#if 0 /* Use NVRAM for environment variables */
 /*-----------------------------------------------------------------------
- * NVRAM organization
- */
-#define CFG_ENV_IS_IN_NVRAM	1	/* use NVRAM for environment vars	*/
-#define CFG_ENV_SIZE		0x0ff8		/* Size of Environment vars	*/
-#define CFG_ENV_ADDR		\
-	(CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-(CFG_ENV_SIZE+8))	/* Env	*/
-
-#else /* Use EEPROM for environment variables */
-
-#define CFG_ENV_IS_IN_EEPROM    1       /* use EEPROM for environment vars */
-#define CFG_ENV_OFFSET          0x000   /* environment starts at the beginning of the EEPROM */
-#define CFG_ENV_SIZE            0x400   /* 1024 bytes may be used for env vars*/
-				   /* total size of a CAT24WC08 is 1024 bytes */
-#endif
-
-#define CFG_NVRAM_BASE_ADDR	0xf0200000		/* NVRAM base address	*/
-#define CFG_NVRAM_SIZE		(32*1024)		/* NVRAM size		*/
-#define CFG_NVRAM_VXWORKS_OFFS	0x6900		/* Offset for VxWorks eth-addr	*/
-
-/*-----------------------------------------------------------------------
- * I2C EEPROM (CAT24WC08) for environment
+ * I2C EEPROM (CAT24WC32) for environment
  */
 #define CONFIG_HARD_I2C			/* I2c with hardware support */
 #define CFG_I2C_SPEED		400000	/* I2C speed and slave address */
 #define CFG_I2C_SLAVE		0x7F
 
-#define CFG_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC08		*/
-#define CFG_I2C_EEPROM_ADDR_LEN	1	/* Bytes of address		*/
+#define CFG_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC32		*/
+#define CFG_I2C_EEPROM_ADDR_LEN	2	/* Bytes of address		*/
 /* mask of address bits that overflow into the "EEPROM chip address"    */
-#define CFG_I2C_EEPROM_ADDR_OVERFLOW	0x07
-#define CFG_EEPROM_PAGE_WRITE_BITS 4	/* The Catalyst CAT24WC08 has	*/
-					/* 16 byte page write mode using*/
-					/* last	4 bits of the address	*/
+#define CFG_I2C_EEPROM_ADDR_OVERFLOW	0x01
+#define CFG_EEPROM_PAGE_WRITE_BITS 5	/* The Catalyst CAT24WC32 has	*/
+					/* 32 byte page write mode using*/
+					/* last	5 bits of the address	*/
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
 #define CFG_EEPROM_PAGE_WRITE_ENABLE
 
+/* Use EEPROM for environment variables */
+
+#define CFG_ENV_IS_IN_EEPROM    1       /* use EEPROM for environment vars */
+#define CFG_ENV_OFFSET          0x000   /* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE            0x800   /* 2048 bytes may be used for env vars*/
+				   /* total size of a CAT24WC32 is 4096 bytes */
+
+#define CFG_NVRAM_BASE_ADDR	0xf0200000		/* NVRAM base address	*/
+#define CFG_NVRAM_SIZE		(32*1024)		/* NVRAM size		*/
+#define CFG_NVRAM_VXWORKS_OFFS	0x6900		/* Offset for VxWorks eth-addr	*/
+
 /*-----------------------------------------------------------------------
  * Cache Configuration
  */

include/configs/DP405.h

@@ -0,0 +1,346 @@
+/*
+ * (C) Copyright 2001-2003
+ * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_405EP		1	/* This is a PPC405 CPU		*/
+#define CONFIG_4xx		1	/* ...member of PPC4xx family   */
+#define CONFIG_DP405		1	/* ...on a DP405 board 	        */
+
+#define CONFIG_BOARD_PRE_INIT   1       /* call board_pre_init()        */
+#define CONFIG_MISC_INIT_R      1       /* call misc_init_r()           */
+
+#define CONFIG_SYS_CLK_FREQ     33333334 /* external frequency to pll   */
+
+#define CONFIG_BAUDRATE		9600
+#define CONFIG_BOOTDELAY	3	/* autoboot after 3 seconds	*/
+
+#undef	CONFIG_BOOTARGS
+#define CONFIG_RAMBOOTCOMMAND							\
+	"setenv bootargs root=/dev/ram rw nfsroot=$(serverip):$(rootpath) "	\
+	"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;"	\
+	"bootm ffc00000 ffca0000"
+#define CONFIG_NFSBOOTCOMMAND							\
+	"setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) "	\
+	"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;"	\
+	"bootm ffc00000"
+#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
+#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
+
+#define CONFIG_MII		1	/* MII PHY management		*/
+#define	CONFIG_PHY_ADDR		0	/* PHY address			*/
+
+#define CONFIG_COMMANDS	      ( CONFIG_CMD_DFL	| \
+				CFG_CMD_BSP	| \
+				CFG_CMD_DHCP	| \
+				CFG_CMD_IRQ	| \
+				CFG_CMD_ELF	| \
+				CFG_CMD_DATE	| \
+				CFG_CMD_I2C	| \
+				CFG_CMD_EEPROM  )
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+#undef  CONFIG_WATCHDOG			/* watchdog disabled		*/
+
+#define CONFIG_RTC_MC146818             /* DS1685 is MC146818 compatible*/
+#define CFG_RTC_REG_BASE_ADDR	 0xF0000500 /* RTC Base Address         */
+
+#define	CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP			/* undef to save memory		*/
+#define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
+
+#undef	CFG_HUSH_PARSER			/* use "hush" command parser	*/
+#ifdef	CFG_HUSH_PARSER
+#define	CFG_PROMPT_HUSH_PS2	"> "
+#endif
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define	CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#else
+#define	CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS	16		/* max number of command args	*/
+#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+
+#define CFG_DEVICE_NULLDEV      1       /* include nulldev device       */
+
+#define CFG_CONSOLE_INFO_QUIET  1       /* don't print console @ startup*/
+
+#define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
+#define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
+
+#undef  CFG_EXT_SERIAL_CLOCK           /* no external serial clock used */
+#define CFG_IGNORE_405_UART_ERRATA_59   /* ignore ppc405gp errata #59   */
+#define CFG_BASE_BAUD       691200
+#undef  CONFIG_UART1_CONSOLE            /* define for uart1 as console  */
+
+/* The following table includes the supported baudrates */
+#define CFG_BAUDRATE_TABLE      \
+	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400,     \
+	 57600, 115200, 230400, 460800, 921600 }
+
+#define CFG_LOAD_ADDR	0x100000	/* default load address */
+#define CFG_EXTBDINFO	1		/* To use extended board_into (bd_t) */
+
+#define	CFG_HZ		1000		/* decrementer freq: 1 ms ticks	*/
+
+#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
+
+#define CONFIG_VERSION_VARIABLE	1       /* include version env variable */
+
+#define CFG_RX_ETH_BUFFER	16      /* use 16 rx buffer on 405 emac */
+
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ *-----------------------------------------------------------------------
+ */
+#define PCI_HOST_ADAPTER 0              /* configure as pci adapter     */
+#define PCI_HOST_FORCE  1               /* configure as pci host        */
+#define PCI_HOST_AUTO   2               /* detected via arbiter enable  */
+
+#define CONFIG_PCI			/* include pci support	        */
+#define CONFIG_PCI_HOST	PCI_HOST_HOST   /* select pci host function     */
+#undef  CONFIG_PCI_PNP			/* do pci plug-and-play         */
+					/* resource configuration       */
+
+#undef  CONFIG_PCI_SCAN_SHOW            /* print pci devices @ startup  */
+
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE  /* PCI Vendor ID: esd gmbh      */
+#define CFG_PCI_SUBSYS_DEVICEID 0x0405  /* PCI Device ID: CPCI-405      */
+#define CFG_PCI_CLASSCODE       0x0b20  /* PCI Class Code: Processor/PPC*/
+#define CFG_PCI_PTM1LA  0x00000000      /* point to sdram               */
+#define CFG_PCI_PTM1MS  0xfc000001      /* 64MB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000      /* Host: use this pci address   */
+#define CFG_PCI_PTM2LA  0xffc00000      /* point to flash               */
+#define CFG_PCI_PTM2MS  0xffc00001      /* 4MB, enable                  */
+#define CFG_PCI_PTM2PCI 0x04000000      /* Host: use this pci address   */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define FLASH_BASE0_PRELIM	0xFFC00000	/* FLASH bank #0	*/
+
+#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
+#define CFG_MAX_FLASH_SECT	256	/* max number of sectors on one chip	*/
+
+#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
+#define CFG_FLASH_WRITE_TOUT	1000	/* Timeout for Flash Write (in ms)	*/
+
+#define CFG_FLASH_WORD_SIZE     unsigned short  /* flash word size (width)      */
+#define CFG_FLASH_ADDR0         0x5555  /* 1st address for flash config cycles  */
+#define CFG_FLASH_ADDR1         0x2AAA  /* 2nd address for flash config cycles  */
+/*
+ * The following defines are added for buggy IOP480 byte interface.
+ * All other boards should use the standard values (CPCI405 etc.)
+ */
+#define CFG_FLASH_READ0         0x0000  /* 0 is standard                        */
+#define CFG_FLASH_READ1         0x0001  /* 1 is standard                        */
+#define CFG_FLASH_READ2         0x0002  /* 2 is standard                        */
+
+#define CFG_FLASH_EMPTY_INFO            /* print 'E' for empty sector on flinfo */
+
+#if 0 /* test-only */
+#define CFG_JFFS2_FIRST_BANK    0           /* use for JFFS2 */
+#define CFG_JFFS2_NUM_BANKS     1           /* ! second bank contains U-Boot */
+#endif
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE		0x00000000
+#define CFG_FLASH_BASE		0xFFFC0000
+#define CFG_MONITOR_BASE	TEXT_BASE
+#define CFG_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB for Monitor	*/
+#define CFG_MALLOC_LEN		(256 * 1024)	/* Reserve 256 kB for malloc()	*/
+
+#if (CFG_MONITOR_BASE < FLASH_BASE0_PRELIM)
+# define CFG_RAMBOOT		1
+#else
+# undef CFG_RAMBOOT
+#endif
+
+/*-----------------------------------------------------------------------
+ * Environment Variable setup
+ */
+#define CFG_ENV_IS_IN_EEPROM    1       /* use EEPROM for environment vars */
+#define CFG_ENV_OFFSET          0x100   /* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE            0x700   /* 2048 bytes may be used for env vars*/
+				   /* total size of a CAT24WC16 is 2048 bytes */
+
+#define CFG_NVRAM_BASE_ADDR	0xF0000500		/* NVRAM base address	*/
+#define CFG_NVRAM_SIZE		242		        /* NVRAM size		*/
+
+/*-----------------------------------------------------------------------
+ * I2C EEPROM (CAT24WC16) for environment
+ */
+#define CONFIG_HARD_I2C			/* I2c with hardware support */
+#define CFG_I2C_SPEED		400000	/* I2C speed and slave address */
+#define CFG_I2C_SLAVE		0x7F
+
+#define CFG_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC08		*/
+#define CFG_I2C_EEPROM_ADDR_LEN	1	/* Bytes of address		*/
+/* mask of address bits that overflow into the "EEPROM chip address"    */
+#define CFG_I2C_EEPROM_ADDR_OVERFLOW	0x07
+#define CFG_EEPROM_PAGE_WRITE_BITS 4	/* The Catalyst CAT24WC08 has	*/
+					/* 16 byte page write mode using*/
+					/* last	4 bits of the address	*/
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
+#define CFG_EEPROM_PAGE_WRITE_ENABLE
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_DCACHE_SIZE		16384	/* For IBM 405 CPUs, older 405 ppc's    */
+					/* have only 8kB, 16kB is save here     */
+#define CFG_CACHELINE_SIZE	32	/* ...			*/
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
+#endif
+
+/*-----------------------------------------------------------------------
+ * External Bus Controller (EBC) Setup
+ */
+
+#define CAN_BA          0xF0000000          /* CAN Base Address                 */
+#define RTC_BA          0xF0000500          /* RTC Base Address                 */
+
+/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization                       */
+#define CFG_EBC_PB0AP           0x92015480
+#define CFG_EBC_PB0CR           0xFFC5A000  /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
+
+#if 0 /* test-only */
+/* Memory Bank 1 (Flash Bank 1, NAND-FLASH) initialization                      */
+#define CFG_EBC_PB1AP           0x92015480
+#define CFG_EBC_PB1CR           0xF4018000  /* BAS=0xF40,BS=1MB,BU=R/W,BW=8bit  */
+#endif
+
+/* Memory Bank 2 (8 Bit Peripheral: CAN, UART, RTC) initialization              */
+#define CFG_EBC_PB2AP           0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB2CR           0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit  */
+
+/*-----------------------------------------------------------------------
+ * FPGA stuff
+ */
+#define CFG_FPGA_XC95XL         1           /* using Xilinx XC95XL CPLD      */
+#define CFG_FPGA_MAX_SIZE       32*1024     /* 32kByte is enough for CPLD    */
+
+/* FPGA program pin configuration */
+#define CFG_FPGA_PRG            0x04000000  /* JTAG TMS pin (ppc output)     */
+#define CFG_FPGA_CLK            0x02000000  /* JTAG TCK pin (ppc output)     */
+#define CFG_FPGA_DATA           0x01000000  /* JTAG TDO->TDI data pin (ppc output) */
+#define CFG_FPGA_INIT           0x00010000  /* unused (ppc input)            */
+#define CFG_FPGA_DONE           0x00008000  /* JTAG TDI->TDO pin (ppc input) */
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in data cache)
+ */
+/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
+#define CFG_TEMP_STACK_OCM        1
+
+/* On Chip Memory location */
+#define CFG_OCM_DATA_ADDR	0xF8000000
+#define CFG_OCM_DATA_SIZE	0x1000
+#define CFG_INIT_RAM_ADDR	CFG_OCM_DATA_ADDR /* inside of SDRAM		*/
+#define CFG_INIT_RAM_END	CFG_OCM_DATA_SIZE /* End of used area in RAM	*/
+
+#define CFG_GBL_DATA_SIZE      128  /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET    (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET      CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Definitions for GPIO setup (PPC405EP specific)
+ *
+ * GPIO0[0]     - External Bus Controller BLAST output
+ * GPIO0[1-9]   - Instruction trace outputs -> GPIO
+ * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
+ * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs -> GPIO
+ * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
+ * GPIO0[24-27] - UART0 control signal inputs/outputs
+ * GPIO0[28-29] - UART1 data signal input/output
+ * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
+ */
+/* GPIO Input:          OSR=00, ISR=00, TSR=00, TCR=0 */
+/* GPIO Output:         OSR=00, ISR=00, TSR=00, TCR=1 */
+/* Alt. Funtion Input:  OSR=00, ISR=01, TSR=00, TCR=0 */
+/* Alt. Funtion Output: OSR=01, ISR=00, TSR=00, TCR=1 */
+#define CFG_GPIO0_OSRH          0x40000540  /*  0 ... 15 */
+#define CFG_GPIO0_OSRL          0x00000110  /* 16 ... 31 */
+#define CFG_GPIO0_ISR1H         0x00000000  /*  0 ... 15 */
+#define CFG_GPIO0_ISR1L         0x14000045  /* 16 ... 31 */
+#define CFG_GPIO0_TSRH          0x00000000  /*  0 ... 15 */
+#define CFG_GPIO0_TSRL          0x00000000  /* 16 ... 31 */
+#define CFG_GPIO0_TCR           0xF7FE0014  /*  0 ... 31 */
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
+#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
+
+/*
+ * Default speed selection (cpu_plb_opb_ebc) in mhz.
+ * This value will be set if iic boot eprom is disabled.
+ */
+#if 0
+#define PLLMR0_DEFAULT   PLLMR0_266_133_66_33
+#define PLLMR1_DEFAULT   PLLMR1_266_133_66_33
+#endif
+#if 0
+#define PLLMR0_DEFAULT   PLLMR0_200_100_50_33
+#define PLLMR1_DEFAULT   PLLMR1_200_100_50_33
+#endif
+#if 1
+#define PLLMR0_DEFAULT   PLLMR0_133_66_66_33
+#define PLLMR1_DEFAULT   PLLMR1_133_66_66_33
+#endif
+
+#endif	/* __CONFIG_H */

include/configs/HUB405.h

@@ -0,0 +1,382 @@
+/*
+ * (C) Copyright 2001-2003
+ * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_405EP		1	/* This is a PPC405 CPU		*/
+#define CONFIG_4xx		1	/* ...member of PPC4xx family   */
+#define CONFIG_HUB405		1	/* ...on a ASH405 board 	*/
+
+#define CONFIG_BOARD_PRE_INIT   1       /* call board_pre_init()        */
+#define CONFIG_MISC_INIT_R      1       /* call misc_init_r()           */
+
+#define CONFIG_SYS_CLK_FREQ     33333334 /* external frequency to pll   */
+
+#define CONFIG_BAUDRATE		9600
+#define CONFIG_BOOTDELAY	3	/* autoboot after 3 seconds	*/
+
+#undef	CONFIG_BOOTARGS
+#define CONFIG_RAMBOOTCOMMAND							\
+	"setenv bootargs root=/dev/ram rw nfsroot=$(serverip):$(rootpath) "	\
+	"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;"	\
+	"bootm ffc00000 ffca0000"
+#define CONFIG_NFSBOOTCOMMAND							\
+	"setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) "	\
+	"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;"	\
+	"bootm ffc00000"
+#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
+#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
+
+#define CONFIG_MII		1	/* MII PHY management		*/
+#define	CONFIG_PHY_ADDR		0	/* PHY address			*/
+
+#define CONFIG_COMMANDS	      ( CONFIG_CMD_DFL	| \
+				CFG_CMD_DHCP	| \
+				CFG_CMD_IRQ	| \
+				CFG_CMD_ELF	| \
+				CFG_CMD_NAND	| \
+				CFG_CMD_I2C	| \
+				CFG_CMD_MII	| \
+				CFG_CMD_PING	| \
+				CFG_CMD_EEPROM  )
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+#undef  CONFIG_WATCHDOG			/* watchdog disabled		*/
+
+#define	CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP			/* undef to save memory		*/
+#define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
+
+#undef	CFG_HUSH_PARSER			/* use "hush" command parser	*/
+#ifdef	CFG_HUSH_PARSER
+#define	CFG_PROMPT_HUSH_PS2	"> "
+#endif
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define	CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#else
+#define	CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS	16		/* max number of command args	*/
+#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+
+#define CFG_DEVICE_NULLDEV      1       /* include nulldev device       */
+
+#define CFG_CONSOLE_INFO_QUIET  1       /* don't print console @ startup*/
+
+#define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
+#define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
+
+#undef  CFG_EXT_SERIAL_CLOCK           /* no external serial clock used */
+#define CFG_IGNORE_405_UART_ERRATA_59   /* ignore ppc405gp errata #59   */
+#define CFG_BASE_BAUD       691200
+#undef  CONFIG_UART1_CONSOLE            /* define for uart1 as console  */
+
+/* The following table includes the supported baudrates */
+#define CFG_BAUDRATE_TABLE      \
+	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400,     \
+	 57600, 115200, 230400, 460800, 921600 }
+
+#define CFG_LOAD_ADDR	0x100000	/* default load address */
+#define CFG_EXTBDINFO	1		/* To use extended board_into (bd_t) */
+
+#define	CFG_HZ		1000		/* decrementer freq: 1 ms ticks	*/
+
+#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
+
+#define CONFIG_VERSION_VARIABLE	1       /* include version env variable */
+
+#define CFG_RX_ETH_BUFFER	16      /* use 16 rx buffer on 405 emac */
+
+/*-----------------------------------------------------------------------
+ * NAND-FLASH stuff
+ *-----------------------------------------------------------------------
+ */
+#define CFG_MAX_NAND_DEVICE	1	/* Max number of NAND devices		*/
+#define SECTORSIZE 512
+
+#define ADDR_COLUMN 1
+#define ADDR_PAGE 2
+#define ADDR_COLUMN_PAGE 3
+
+#define NAND_ChipID_UNKNOWN 	0x00
+#define NAND_MAX_FLOORS 1
+#define NAND_MAX_CHIPS 1
+
+#define CFG_NAND_CE  (0x80000000 >> 1)  /* our CE is GPIO1 */
+#define CFG_NAND_CLE (0x80000000 >> 2)  /* our CLE is GPIO2 */
+#define CFG_NAND_ALE (0x80000000 >> 3)  /* our ALE is GPIO3 */
+#define CFG_NAND_RDY (0x80000000 >> 4)  /* our RDY is GPIO4 */
+
+#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
+#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
+#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0)
+#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0)
+#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0)
+#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0)
+#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY))
+
+#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
+#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
+#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
+#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
+
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ *-----------------------------------------------------------------------
+ */
+#define PCI_HOST_ADAPTER 0              /* configure as pci adapter     */
+#define PCI_HOST_FORCE  1               /* configure as pci host        */
+#define PCI_HOST_AUTO   2               /* detected via arbiter enable  */
+
+#undef  CONFIG_PCI			/* include pci support	        */
+#define CONFIG_PCI_HOST	PCI_HOST_HOST   /* select pci host function     */
+#undef  CONFIG_PCI_PNP			/* do pci plug-and-play         */
+					/* resource configuration       */
+
+#undef  CONFIG_PCI_SCAN_SHOW            /* print pci devices @ startup  */
+
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE  /* PCI Vendor ID: esd gmbh      */
+#define CFG_PCI_SUBSYS_DEVICEID 0x0405  /* PCI Device ID: CPCI-405      */
+#define CFG_PCI_CLASSCODE       0x0b20  /* PCI Class Code: Processor/PPC*/
+#define CFG_PCI_PTM1LA  0x00000000      /* point to sdram               */
+#define CFG_PCI_PTM1MS  0xfc000001      /* 64MB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000      /* Host: use this pci address   */
+#define CFG_PCI_PTM2LA  0xffc00000      /* point to flash               */
+#define CFG_PCI_PTM2MS  0xffc00001      /* 4MB, enable                  */
+#define CFG_PCI_PTM2PCI 0x04000000      /* Host: use this pci address   */
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE		0x00000000
+#define CFG_FLASH_BASE		0xFFFC0000
+#define CFG_MONITOR_BASE	CFG_FLASH_BASE
+#define CFG_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB for Monitor	*/
+#define CFG_MALLOC_LEN		(256 * 1024)	/* Reserve 256 kB for malloc()	*/
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
+#define CFG_MAX_FLASH_SECT	256	/* max number of sectors on one chip	*/
+
+#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
+#define CFG_FLASH_WRITE_TOUT	1000	/* Timeout for Flash Write (in ms)	*/
+
+#define CFG_FLASH_WORD_SIZE     unsigned short  /* flash word size (width)      */
+#define CFG_FLASH_ADDR0         0x5555  /* 1st address for flash config cycles  */
+#define CFG_FLASH_ADDR1         0x2AAA  /* 2nd address for flash config cycles  */
+/*
+ * The following defines are added for buggy IOP480 byte interface.
+ * All other boards should use the standard values (CPCI405 etc.)
+ */
+#define CFG_FLASH_READ0         0x0000  /* 0 is standard                        */
+#define CFG_FLASH_READ1         0x0001  /* 1 is standard                        */
+#define CFG_FLASH_READ2         0x0002  /* 2 is standard                        */
+
+#define CFG_FLASH_EMPTY_INFO            /* print 'E' for empty sector on flinfo */
+
+#if 0 /* test-only */
+#define CFG_JFFS2_FIRST_BANK    0           /* use for JFFS2 */
+#define CFG_JFFS2_NUM_BANKS     1           /* ! second bank contains U-Boot */
+#endif
+
+/*-----------------------------------------------------------------------
+ * Environment Variable setup
+ */
+#define CFG_ENV_IS_IN_EEPROM    1       /* use EEPROM for environment vars */
+#define CFG_ENV_OFFSET          0x100   /* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE            0x700   /* 2048 bytes may be used for env vars*/
+				   /* total size of a CAT24WC16 is 2048 bytes */
+
+#define CFG_NVRAM_BASE_ADDR	0xF0000500		/* NVRAM base address	*/
+#define CFG_NVRAM_SIZE		242		        /* NVRAM size		*/
+
+/*-----------------------------------------------------------------------
+ * I2C EEPROM (CAT24WC16) for environment
+ */
+#define CONFIG_HARD_I2C			/* I2c with hardware support */
+#define CFG_I2C_SPEED		400000	/* I2C speed and slave address */
+#define CFG_I2C_SLAVE		0x7F
+
+#define CFG_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC08		*/
+#define CFG_I2C_EEPROM_ADDR_LEN	1	/* Bytes of address		*/
+/* mask of address bits that overflow into the "EEPROM chip address"    */
+#define CFG_I2C_EEPROM_ADDR_OVERFLOW	0x07
+#define CFG_EEPROM_PAGE_WRITE_BITS 4	/* The Catalyst CAT24WC08 has	*/
+					/* 16 byte page write mode using*/
+					/* last	4 bits of the address	*/
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
+#define CFG_EEPROM_PAGE_WRITE_ENABLE
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_DCACHE_SIZE		16384	/* For IBM 405 CPUs, older 405 ppc's    */
+					/* have only 8kB, 16kB is save here     */
+#define CFG_CACHELINE_SIZE	32	/* ...			*/
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
+#endif
+
+/*
+ * Init Memory Controller:
+ *
+ * BR0/1 and OR0/1 (FLASH)
+ */
+
+#define FLASH_BASE0_PRELIM	0xFFC00000	/* FLASH bank #0	*/
+
+/*-----------------------------------------------------------------------
+ * External Bus Controller (EBC) Setup
+ */
+
+/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization                       */
+#define CFG_EBC_PB0AP           0x92015480
+/*#define CFG_EBC_PB0AP           0x08055880  /XXX* TWT=16,CSN=1,OEN=1,WBN=1,WBF=1,TH=4,SOR=1 */
+#define CFG_EBC_PB0CR           0xFFC5A000  /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
+
+/* Memory Bank 1 (Flash Bank 1, NAND-FLASH) initialization                      */
+#define CFG_EBC_PB1AP           0x92015480
+#define CFG_EBC_PB1CR           0xF4018000  /* BAS=0xF40,BS=1MB,BU=R/W,BW=8bit  */
+
+/* Memory Bank 2 (8 Bit Peripheral: UART) initialization                        */
+#if 0
+#define CFG_EBC_PB2AP           0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB2CR           0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit  */
+#else
+#define CFG_EBC_PB2AP           0x92015480
+#define CFG_EBC_PB2CR           0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit  */
+#endif
+
+#define DUART0_BA       0xF0000000          /* DUART Base Address               */
+#define DUART1_BA       0xF0000008          /* DUART Base Address               */
+#define DUART2_BA       0xF0000010          /* DUART Base Address               */
+#define DUART3_BA       0xF0000018          /* DUART Base Address               */
+#define CFG_NAND_BASE   0xF4000000
+
+/*-----------------------------------------------------------------------
+ * FPGA stuff
+ */
+#define CFG_FPGA_SPARTAN2       1           /* using Xilinx Spartan 2 now    */
+#define CFG_FPGA_MAX_SIZE       128*1024    /* 128kByte is enough for XC2S50E*/
+
+/* FPGA program pin configuration */
+#define CFG_FPGA_PRG            0x04000000  /* FPGA program pin (ppc output) */
+#define CFG_FPGA_CLK            0x02000000  /* FPGA clk pin (ppc output)     */
+#define CFG_FPGA_DATA           0x01000000  /* FPGA data pin (ppc output)    */
+#define CFG_FPGA_INIT           0x00010000  /* FPGA init pin (ppc input)     */
+#define CFG_FPGA_DONE           0x00008000  /* FPGA done pin (ppc input)     */
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in data cache)
+ */
+/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
+#define CFG_TEMP_STACK_OCM        1
+
+/* On Chip Memory location */
+#define CFG_OCM_DATA_ADDR	0xF8000000
+#define CFG_OCM_DATA_SIZE	0x1000
+#define CFG_INIT_RAM_ADDR	CFG_OCM_DATA_ADDR /* inside of SDRAM		*/
+#define CFG_INIT_RAM_END	CFG_OCM_DATA_SIZE /* End of used area in RAM	*/
+
+#define CFG_GBL_DATA_SIZE      128  /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET    (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET      CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Definitions for GPIO setup (PPC405EP specific)
+ *
+ * GPIO0[0]     - External Bus Controller BLAST output
+ * GPIO0[1-9]   - Instruction trace outputs -> GPIO
+ * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
+ * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs -> GPIO
+ * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
+ * GPIO0[24-27] - UART0 control signal inputs/outputs
+ * GPIO0[28-29] - UART1 data signal input/output
+ * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
+ */
+#define CFG_GPIO0_OSRH          0x40000550
+#define CFG_GPIO0_OSRL          0x00000110
+#define CFG_GPIO0_ISR1H         0x00000000
+#define CFG_GPIO0_ISR1L         0x15555445
+#define CFG_GPIO0_TSRH          0x00000000
+#define CFG_GPIO0_TSRL          0x00000000
+#define CFG_GPIO0_TCR           0xF7FE0014
+
+#define CFG_DUART_RST           (0x80000000 >> 14)
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
+#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
+
+/*
+ * Default speed selection (cpu_plb_opb_ebc) in mhz.
+ * This value will be set if iic boot eprom is disabled.
+ */
+#if 0
+#define PLLMR0_DEFAULT   PLLMR0_266_133_66_33
+#define PLLMR1_DEFAULT   PLLMR1_266_133_66_33
+#endif
+#if 0
+#define PLLMR0_DEFAULT   PLLMR0_200_100_50_33
+#define PLLMR1_DEFAULT   PLLMR1_200_100_50_33
+#endif
+#if 1
+#define PLLMR0_DEFAULT   PLLMR0_133_66_66_33
+#define PLLMR1_DEFAULT   PLLMR1_133_66_66_33
+#endif
+
+#endif	/* __CONFIG_H */

include/configs/PCI405.h

@@ -133,6 +133,8 @@
 
 #undef CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
 
+#define CONFIG_VERSION_VARIABLE	1       /* include version env variable */
+
 /*-----------------------------------------------------------------------
  * PCI stuff
  *-----------------------------------------------------------------------

include/configs/PLU405.h

@@ -0,0 +1,431 @@
+/*
+ * (C) Copyright 2001-2003
+ * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_405EP		1	/* This is a PPC405 CPU		*/
+#define CONFIG_4xx		1	/* ...member of PPC4xx family   */
+#define CONFIG_PLU405		1	/* ...on a PLU405 board 	*/
+
+#define CONFIG_BOARD_PRE_INIT   1       /* call board_pre_init()        */
+#define CONFIG_MISC_INIT_R      1       /* call misc_init_r()           */
+
+#define CONFIG_SYS_CLK_FREQ     33333334 /* external frequency to pll   */
+
+#define CONFIG_BAUDRATE		9600
+#define CONFIG_BOOTDELAY	3	/* autoboot after 3 seconds	*/
+
+#undef	CONFIG_BOOTARGS
+#define CONFIG_RAMBOOTCOMMAND							\
+	"setenv bootargs root=/dev/ram rw nfsroot=$(serverip):$(rootpath) "	\
+	"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;"	\
+	"bootm ffc00000 ffca0000"
+#define CONFIG_NFSBOOTCOMMAND							\
+	"setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) "	\
+	"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;"	\
+	"bootm ffc00000"
+#define CONFIG_BOOTCOMMAND "bootm fff00000"
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
+#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
+
+#define CONFIG_MII		1	/* MII PHY management		*/
+#define	CONFIG_PHY_ADDR		0	/* PHY address			*/
+
+#define CONFIG_COMMANDS	      ( CONFIG_CMD_DFL	| \
+				CFG_CMD_DHCP	| \
+				CFG_CMD_PCI	| \
+				CFG_CMD_IRQ	| \
+				CFG_CMD_IDE	| \
+				CFG_CMD_ELF	| \
+				CFG_CMD_NAND	| \
+				CFG_CMD_DATE	| \
+				CFG_CMD_I2C	| \
+				CFG_CMD_MII	| \
+				CFG_CMD_PING	| \
+				CFG_CMD_EEPROM  )
+
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+#undef  CONFIG_WATCHDOG			/* watchdog disabled		*/
+
+#define CONFIG_RTC_MC146818             /* DS1685 is MC146818 compatible*/
+#define CFG_RTC_REG_BASE_ADDR	 0xF0000500 /* RTC Base Address         */
+
+#define	CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP			/* undef to save memory		*/
+#define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
+
+#undef	CFG_HUSH_PARSER			/* use "hush" command parser	*/
+#ifdef	CFG_HUSH_PARSER
+#define	CFG_PROMPT_HUSH_PS2	"> "
+#endif
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define	CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#else
+#define	CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS	16		/* max number of command args	*/
+#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+
+#define CFG_DEVICE_NULLDEV      1       /* include nulldev device       */
+
+#define CFG_CONSOLE_INFO_QUIET  1       /* don't print console @ startup*/
+
+#define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
+#define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
+
+#undef  CFG_EXT_SERIAL_CLOCK           /* no external serial clock used */
+#define CFG_IGNORE_405_UART_ERRATA_59   /* ignore ppc405gp errata #59   */
+#define CFG_BASE_BAUD       691200
+#undef  CONFIG_UART1_CONSOLE            /* define for uart1 as console  */
+
+/* The following table includes the supported baudrates */
+#define CFG_BAUDRATE_TABLE      \
+	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400,     \
+	 57600, 115200, 230400, 460800, 921600 }
+
+#define CFG_LOAD_ADDR	0x100000	/* default load address */
+#define CFG_EXTBDINFO	1		/* To use extended board_into (bd_t) */
+
+#define	CFG_HZ		1000		/* decrementer freq: 1 ms ticks	*/
+
+#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
+
+#define CONFIG_VERSION_VARIABLE	1       /* include version env variable */
+
+#define CFG_RX_ETH_BUFFER	16      /* use 16 rx buffer on 405 emac */
+
+/*-----------------------------------------------------------------------
+ * NAND-FLASH stuff
+ *-----------------------------------------------------------------------
+ */
+#define CFG_MAX_NAND_DEVICE	1	/* Max number of NAND devices		*/
+#define SECTORSIZE 512
+
+#define ADDR_COLUMN 1
+#define ADDR_PAGE 2
+#define ADDR_COLUMN_PAGE 3
+
+#define NAND_ChipID_UNKNOWN 	0x00
+#define NAND_MAX_FLOORS 1
+#define NAND_MAX_CHIPS 1
+
+#define CFG_NAND_CE  (0x80000000 >> 1)  /* our CE is GPIO1 */
+#define CFG_NAND_CLE (0x80000000 >> 2)  /* our CLE is GPIO2 */
+#define CFG_NAND_ALE (0x80000000 >> 3)  /* our ALE is GPIO3 */
+#define CFG_NAND_RDY (0x80000000 >> 4)  /* our RDY is GPIO4 */
+
+#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
+#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
+#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0)
+#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0)
+#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0)
+#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0)
+#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY))
+
+#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
+#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
+#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
+#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
+
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ *-----------------------------------------------------------------------
+ */
+#define PCI_HOST_ADAPTER 0              /* configure as pci adapter     */
+#define PCI_HOST_FORCE  1               /* configure as pci host        */
+#define PCI_HOST_AUTO   2               /* detected via arbiter enable  */
+
+#define CONFIG_PCI			/* include pci support	        */
+#define CONFIG_PCI_HOST	PCI_HOST_HOST   /* select pci host function     */
+#define CONFIG_PCI_PNP			/* do pci plug-and-play         */
+					/* resource configuration       */
+
+#define CONFIG_PCI_SCAN_SHOW            /* print pci devices @ startup  */
+
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE  /* PCI Vendor ID: esd gmbh      */
+#define CFG_PCI_SUBSYS_DEVICEID 0x0405  /* PCI Device ID: CPCI-405      */
+#define CFG_PCI_CLASSCODE       0x0b20  /* PCI Class Code: Processor/PPC*/
+#define CFG_PCI_PTM1LA  0x00000000      /* point to sdram               */
+#define CFG_PCI_PTM1MS  0xfc000001      /* 64MB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000      /* Host: use this pci address   */
+#define CFG_PCI_PTM2LA  0xffc00000      /* point to flash               */
+#define CFG_PCI_PTM2MS  0xffc00001      /* 4MB, enable                  */
+#define CFG_PCI_PTM2PCI 0x04000000      /* Host: use this pci address   */
+
+/*-----------------------------------------------------------------------
+ * IDE/ATA stuff
+ *-----------------------------------------------------------------------
+ */
+#undef  CONFIG_IDE_8xx_DIRECT               /* no pcmcia interface required */
+#undef  CONFIG_IDE_LED                  /* no led for ide supported     */
+#define CONFIG_IDE_RESET	1	/* reset for ide supported	*/
+
+#define	CFG_IDE_MAXBUS	        1		/* max. 1 IDE busses	*/
+#define	CFG_IDE_MAXDEVICE	(CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
+
+#define	CFG_ATA_BASE_ADDR	0xF0100000
+#define	CFG_ATA_IDE0_OFFSET	0x0000
+
+#define CFG_ATA_DATA_OFFSET	0x0000	/* Offset for data I/O			*/
+#define	CFG_ATA_REG_OFFSET	0x0000	/* Offset for normal register accesses	*/
+#define CFG_ATA_ALT_OFFSET	0x0000	/* Offset for alternate registers	*/
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define FLASH_BASE0_PRELIM	0xFFC00000	/* FLASH bank #0	*/
+
+#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
+#define CFG_MAX_FLASH_SECT	256	/* max number of sectors on one chip	*/
+
+#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
+#define CFG_FLASH_WRITE_TOUT	1000	/* Timeout for Flash Write (in ms)	*/
+
+#define CFG_FLASH_WORD_SIZE     unsigned short  /* flash word size (width)      */
+#define CFG_FLASH_ADDR0         0x5555  /* 1st address for flash config cycles  */
+#define CFG_FLASH_ADDR1         0x2AAA  /* 2nd address for flash config cycles  */
+/*
+ * The following defines are added for buggy IOP480 byte interface.
+ * All other boards should use the standard values (CPCI405 etc.)
+ */
+#define CFG_FLASH_READ0         0x0000  /* 0 is standard                        */
+#define CFG_FLASH_READ1         0x0001  /* 1 is standard                        */
+#define CFG_FLASH_READ2         0x0002  /* 2 is standard                        */
+
+#define CFG_FLASH_EMPTY_INFO            /* print 'E' for empty sector on flinfo */
+
+#if 0 /* test-only */
+#define CFG_JFFS2_FIRST_BANK    0           /* use for JFFS2 */
+#define CFG_JFFS2_NUM_BANKS     1           /* ! second bank contains U-Boot */
+#endif
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE		0x00000000
+#define CFG_FLASH_BASE		0xFFFC0000
+#define CFG_MONITOR_BASE	TEXT_BASE
+#define CFG_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB for Monitor	*/
+#define CFG_MALLOC_LEN		(256 * 1024)	/* Reserve 256 kB for malloc()	*/
+
+#if (CFG_MONITOR_BASE < FLASH_BASE0_PRELIM)
+# define CFG_RAMBOOT		1
+#else
+# undef CFG_RAMBOOT
+#endif
+
+/*-----------------------------------------------------------------------
+ * Environment Variable setup
+ */
+#define CFG_ENV_IS_IN_EEPROM    1       /* use EEPROM for environment vars */
+#define CFG_ENV_OFFSET          0x100   /* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE            0x700   /* 2048 bytes may be used for env vars*/
+				   /* total size of a CAT24WC16 is 2048 bytes */
+
+#define CFG_NVRAM_BASE_ADDR	0xF0000500		/* NVRAM base address	*/
+#define CFG_NVRAM_SIZE		242		        /* NVRAM size		*/
+
+/*-----------------------------------------------------------------------
+ * I2C EEPROM (CAT24WC16) for environment
+ */
+#define CONFIG_HARD_I2C			/* I2c with hardware support */
+#define CFG_I2C_SPEED		400000	/* I2C speed and slave address */
+#define CFG_I2C_SLAVE		0x7F
+
+#define CFG_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT24WC08		*/
+#if 1 /* test-only */
+/* CAT24WC08/16... */
+#define CFG_I2C_EEPROM_ADDR_LEN	1	/* Bytes of address		*/
+/* mask of address bits that overflow into the "EEPROM chip address"    */
+#define CFG_I2C_EEPROM_ADDR_OVERFLOW	0x07
+#define CFG_EEPROM_PAGE_WRITE_BITS 4	/* The Catalyst CAT24WC08 has	*/
+					/* 16 byte page write mode using*/
+					/* last	4 bits of the address	*/
+#else
+/* CAT24WC32/64... */
+#define CFG_I2C_EEPROM_ADDR_LEN	2	/* Bytes of address		*/
+/* mask of address bits that overflow into the "EEPROM chip address"    */
+#define CFG_I2C_EEPROM_ADDR_OVERFLOW	0x01
+#define CFG_EEPROM_PAGE_WRITE_BITS 5	/* The Catalyst CAT24WC32 has	*/
+					/* 32 byte page write mode using*/
+					/* last	5 bits of the address	*/
+#endif
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
+#define CFG_EEPROM_PAGE_WRITE_ENABLE
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_DCACHE_SIZE		16384	/* For IBM 405 CPUs, older 405 ppc's    */
+					/* have only 8kB, 16kB is save here     */
+#define CFG_CACHELINE_SIZE	32	/* ...			*/
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
+#endif
+
+/*-----------------------------------------------------------------------
+ * External Bus Controller (EBC) Setup
+ */
+
+#define CAN_BA          0xF0000000          /* CAN Base Address                 */
+#define DUART0_BA       0xF0000400          /* DUART Base Address               */
+#define DUART1_BA       0xF0000408          /* DUART Base Address               */
+#define RTC_BA          0xF0000500          /* RTC Base Address                 */
+#define VGA_BA          0xF1000000          /* Epson VGA Base Address           */
+#define CFG_NAND_BASE   0xF4000000          /* NAND FLASH Base Address          */
+
+/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization                       */
+#define CFG_EBC_PB0AP           0x92015480
+/*#define CFG_EBC_PB0AP           0x08055880  /XXX* TWT=16,CSN=1,OEN=1,WBN=1,WBF=1,TH=4,SOR=1 */
+#define CFG_EBC_PB0CR           0xFFC5A000  /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
+
+/* Memory Bank 1 (Flash Bank 1, NAND-FLASH) initialization                      */
+#define CFG_EBC_PB1AP           0x92015480
+#define CFG_EBC_PB1CR           0xF4018000  /* BAS=0xF40,BS=1MB,BU=R/W,BW=8bit  */
+
+/* Memory Bank 2 (8 Bit Peripheral: CAN, UART, RTC) initialization              */
+#define CFG_EBC_PB2AP           0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB2CR           0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit  */
+
+/* Memory Bank 3 (16 Bit Peripheral: FPGA internal, dig. IO) initialization     */
+#define CFG_EBC_PB3AP           0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB3CR           0xF011A000  /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
+
+/*-----------------------------------------------------------------------
+ * FPGA stuff
+ */
+
+#define CFG_FPGA_BASE_ADDR 0xF0100100       /* FPGA internal Base Address       */
+
+/* FPGA internal regs */
+#define CFG_FPGA_CTRL           0x000
+
+/* FPGA Control Reg */
+#define CFG_FPGA_CTRL_CF_RESET  0x0001
+#define CFG_FPGA_CTRL_WDI       0x0002
+#define CFG_FPGA_CTRL_PS2_RESET 0x0020
+
+#define CFG_FPGA_SPARTAN2       1           /* using Xilinx Spartan 2 now    */
+#define CFG_FPGA_MAX_SIZE       128*1024    /* 128kByte is enough for XC2S50E*/
+
+/* FPGA program pin configuration */
+#define CFG_FPGA_PRG            0x04000000  /* FPGA program pin (ppc output) */
+#define CFG_FPGA_CLK            0x02000000  /* FPGA clk pin (ppc output)     */
+#define CFG_FPGA_DATA           0x01000000  /* FPGA data pin (ppc output)    */
+#define CFG_FPGA_INIT           0x00010000  /* FPGA init pin (ppc input)     */
+#define CFG_FPGA_DONE           0x00008000  /* FPGA done pin (ppc input)     */
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in data cache)
+ */
+/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
+#define CFG_TEMP_STACK_OCM        1
+
+/* On Chip Memory location */
+#define CFG_OCM_DATA_ADDR	0xF8000000
+#define CFG_OCM_DATA_SIZE	0x1000
+#define CFG_INIT_RAM_ADDR	CFG_OCM_DATA_ADDR /* inside of SDRAM		*/
+#define CFG_INIT_RAM_END	CFG_OCM_DATA_SIZE /* End of used area in RAM	*/
+
+#define CFG_GBL_DATA_SIZE      128  /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET    (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET      CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Definitions for GPIO setup (PPC405EP specific)
+ *
+ * GPIO0[0]     - External Bus Controller BLAST output
+ * GPIO0[1-9]   - Instruction trace outputs -> GPIO
+ * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
+ * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs -> GPIO
+ * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
+ * GPIO0[24-27] - UART0 control signal inputs/outputs
+ * GPIO0[28-29] - UART1 data signal input/output
+ * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
+ */
+#define CFG_GPIO0_OSRH          0x40000550
+#define CFG_GPIO0_OSRL          0x00000110
+#define CFG_GPIO0_ISR1H         0x00000000
+#define CFG_GPIO0_ISR1L         0x15555445
+#define CFG_GPIO0_TSRH          0x00000000
+#define CFG_GPIO0_TSRL          0x00000000
+#define CFG_GPIO0_TCR           0xF7FE0014
+
+#define CFG_DUART_RST           (0x80000000 >> 14)
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
+#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
+
+/*
+ * Default speed selection (cpu_plb_opb_ebc) in mhz.
+ * This value will be set if iic boot eprom is disabled.
+ */
+#if 0
+#define PLLMR0_DEFAULT   PLLMR0_266_133_66_33
+#define PLLMR1_DEFAULT   PLLMR1_266_133_66_33
+#endif
+#if 0
+#define PLLMR0_DEFAULT   PLLMR0_200_100_50_33
+#define PLLMR1_DEFAULT   PLLMR1_200_100_50_33
+#endif
+#if 1
+#define PLLMR0_DEFAULT   PLLMR0_133_66_66_33
+#define PLLMR1_DEFAULT   PLLMR1_133_66_66_33
+#endif
+
+#endif	/* __CONFIG_H */

include/configs/PMC405.h

@@ -63,6 +63,7 @@
 #define	CONFIG_PHY_ADDR		0	/* PHY address			*/
 
 #define CONFIG_COMMANDS	      ( CONFIG_CMD_DFL	| \
+				CFG_CMD_BSP	| \
 				CFG_CMD_PCI	| \
 				CFG_CMD_IRQ	| \
 				CFG_CMD_ELF	| \
@@ -254,6 +255,19 @@
 #define CFG_EBC_PB3AP   0x010059C0   /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
 #define CFG_EBC_PB3CR   CF_BA | 0x1A000     /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
 
+/*-----------------------------------------------------------------------
+ * FPGA stuff
+ */
+#define CFG_FPGA_XC95XL         1           /* using Xilinx XC95XL CPLD      */
+#define CFG_FPGA_MAX_SIZE       32*1024     /* 32kByte is enough for CPLD    */
+
+/* FPGA program pin configuration */
+#define CFG_FPGA_PRG            0x04000000  /* JTAG TMS pin (ppc output)     */
+#define CFG_FPGA_CLK            0x02000000  /* JTAG TCK pin (ppc output)     */
+#define CFG_FPGA_DATA           0x01000000  /* JTAG TDO->TDI data pin (ppc output) */
+#define CFG_FPGA_INIT           0x00010000  /* unused (ppc input)            */
+#define CFG_FPGA_DONE           0x00008000  /* JTAG TDI->TDO pin (ppc input) */
+
 /*-----------------------------------------------------------------------
  * Definitions for initial stack pointer and data area (in data cache)
  */

include/configs/VOH405.h

@@ -0,0 +1,438 @@
+/*
+ * (C) Copyright 2001-2003
+ * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_405EP		1	/* This is a PPC405 CPU		*/
+#define CONFIG_4xx		1	/* ...member of PPC4xx family   */
+#define CONFIG_VOH405		1	/* ...on a VOH405 board 	*/
+
+#define CONFIG_BOARD_PRE_INIT   1       /* call board_pre_init()        */
+#define CONFIG_MISC_INIT_R      1       /* call misc_init_r()           */
+
+#define CONFIG_SYS_CLK_FREQ     33333334 /* external frequency to pll   */
+
+#define CONFIG_BAUDRATE		9600
+#define CONFIG_BOOTDELAY	3	/* autoboot after 3 seconds	*/
+
+#undef	CONFIG_BOOTARGS
+#define CONFIG_RAMBOOTCOMMAND							\
+	"setenv bootargs root=/dev/ram rw nfsroot=$(serverip):$(rootpath) "	\
+	"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;"	\
+	"bootm ffc00000 ffca0000"
+#define CONFIG_NFSBOOTCOMMAND							\
+	"setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) "	\
+	"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;"	\
+	"bootm ffc00000"
+#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
+#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
+
+#define CONFIG_MII		1	/* MII PHY management		*/
+#define	CONFIG_PHY_ADDR		0	/* PHY address			*/
+
+#define CONFIG_COMMANDS	      ( CONFIG_CMD_DFL	| \
+				CFG_CMD_DHCP	| \
+				CFG_CMD_PCI	| \
+				CFG_CMD_IRQ	| \
+				CFG_CMD_IDE	| \
+				CFG_CMD_ELF	| \
+				CFG_CMD_NAND	| \
+				CFG_CMD_DATE	| \
+				CFG_CMD_I2C	| \
+				CFG_CMD_MII	| \
+				CFG_CMD_PING	| \
+				CFG_CMD_EEPROM  )
+
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+#undef  CONFIG_WATCHDOG			/* watchdog disabled		*/
+
+#define CONFIG_RTC_MC146818             /* DS1685 is MC146818 compatible*/
+#define CFG_RTC_REG_BASE_ADDR	 0xF0000500 /* RTC Base Address         */
+
+#define	CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP			/* undef to save memory		*/
+#define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
+
+#undef	CFG_HUSH_PARSER			/* use "hush" command parser	*/
+#ifdef	CFG_HUSH_PARSER
+#define	CFG_PROMPT_HUSH_PS2	"> "
+#endif
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define	CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#else
+#define	CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS	16		/* max number of command args	*/
+#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+
+#define CFG_DEVICE_NULLDEV      1       /* include nulldev device       */
+
+#define CFG_CONSOLE_INFO_QUIET  1       /* don't print console @ startup*/
+
+#define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
+#define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
+
+#undef  CFG_EXT_SERIAL_CLOCK           /* no external serial clock used */
+#define CFG_IGNORE_405_UART_ERRATA_59   /* ignore ppc405gp errata #59   */
+#define CFG_BASE_BAUD       691200
+#undef CONFIG_UART1_CONSOLE            /* define for uart1 as console  */
+
+/* The following table includes the supported baudrates */
+#define CFG_BAUDRATE_TABLE      \
+	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400,     \
+	 57600, 115200, 230400, 460800, 921600 }
+
+#define CFG_LOAD_ADDR	0x100000	/* default load address */
+#define CFG_EXTBDINFO	1		/* To use extended board_into (bd_t) */
+
+#define	CFG_HZ		1000		/* decrementer freq: 1 ms ticks	*/
+
+#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
+
+#define CONFIG_VERSION_VARIABLE	1       /* include version env variable */
+
+#define CFG_RX_ETH_BUFFER	16      /* use 16 rx buffer on 405 emac */
+
+/*-----------------------------------------------------------------------
+ * NAND-FLASH stuff
+ *-----------------------------------------------------------------------
+ */
+#define CFG_MAX_NAND_DEVICE	1	/* Max number of NAND devices		*/
+#define SECTORSIZE 512
+
+#define ADDR_COLUMN 1
+#define ADDR_PAGE 2
+#define ADDR_COLUMN_PAGE 3
+
+#define NAND_ChipID_UNKNOWN 	0x00
+#define NAND_MAX_FLOORS 1
+#define NAND_MAX_CHIPS 1
+
+#define CFG_NAND_CE  (0x80000000 >> 1)  /* our CE is GPIO1 */
+#define CFG_NAND_CLE (0x80000000 >> 2)  /* our CLE is GPIO2 */
+#define CFG_NAND_ALE (0x80000000 >> 3)  /* our ALE is GPIO3 */
+#define CFG_NAND_RDY (0x80000000 >> 4)  /* our RDY is GPIO4 */
+
+#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
+#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
+#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0)
+#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0)
+#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0)
+#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0)
+#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY))
+
+#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
+#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
+#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
+#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
+
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ *-----------------------------------------------------------------------
+ */
+#define PCI_HOST_ADAPTER 0              /* configure as pci adapter     */
+#define PCI_HOST_FORCE  1               /* configure as pci host        */
+#define PCI_HOST_AUTO   2               /* detected via arbiter enable  */
+
+#define CONFIG_PCI			/* include pci support	        */
+#define CONFIG_PCI_HOST	PCI_HOST_HOST   /* select pci host function     */
+#define CONFIG_PCI_PNP			/* do pci plug-and-play         */
+					/* resource configuration       */
+
+#define CONFIG_PCI_SCAN_SHOW            /* print pci devices @ startup  */
+
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE  /* PCI Vendor ID: esd gmbh      */
+#define CFG_PCI_SUBSYS_DEVICEID 0x0405  /* PCI Device ID: CPCI-405      */
+#define CFG_PCI_CLASSCODE       0x0b20  /* PCI Class Code: Processor/PPC*/
+#define CFG_PCI_PTM1LA  0x00000000      /* point to sdram               */
+#define CFG_PCI_PTM1MS  0xfc000001      /* 64MB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000      /* Host: use this pci address   */
+#define CFG_PCI_PTM2LA  0xffc00000      /* point to flash               */
+#define CFG_PCI_PTM2MS  0xffc00001      /* 4MB, enable                  */
+#define CFG_PCI_PTM2PCI 0x04000000      /* Host: use this pci address   */
+
+/*-----------------------------------------------------------------------
+ * IDE/ATA stuff
+ *-----------------------------------------------------------------------
+ */
+#undef  CONFIG_IDE_8xx_DIRECT               /* no pcmcia interface required */
+#undef  CONFIG_IDE_LED                  /* no led for ide supported     */
+#define CONFIG_IDE_RESET	1	/* reset for ide supported	*/
+
+#define	CFG_IDE_MAXBUS	        2		/* max. 2 IDE busses	*/
+#define	CFG_IDE_MAXDEVICE	(CFG_IDE_MAXBUS*2) /* max. 2 drives per IDE bus */
+
+#define CONFIG_ATAPI	        1	/* ATAPI for Travelstar         */
+
+#define	CFG_ATA_BASE_ADDR	0xF0100000
+#define	CFG_ATA_IDE0_OFFSET	0x0000
+#define	CFG_ATA_IDE1_OFFSET	0x0010
+
+#define CFG_ATA_DATA_OFFSET	0x0000	/* Offset for data I/O			*/
+#define	CFG_ATA_REG_OFFSET	0x0000	/* Offset for normal register accesses	*/
+#define CFG_ATA_ALT_OFFSET	0x0000	/* Offset for alternate registers	*/
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define FLASH_BASE0_PRELIM	0xFFC00000	/* FLASH bank #0	*/
+
+#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
+#define CFG_MAX_FLASH_SECT	256	/* max number of sectors on one chip	*/
+
+#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
+#define CFG_FLASH_WRITE_TOUT	1000	/* Timeout for Flash Write (in ms)	*/
+
+#define CFG_FLASH_WORD_SIZE     unsigned short  /* flash word size (width)      */
+#define CFG_FLASH_ADDR0         0x5555  /* 1st address for flash config cycles  */
+#define CFG_FLASH_ADDR1         0x2AAA  /* 2nd address for flash config cycles  */
+/*
+ * The following defines are added for buggy IOP480 byte interface.
+ * All other boards should use the standard values (CPCI405 etc.)
+ */
+#define CFG_FLASH_READ0         0x0000  /* 0 is standard                        */
+#define CFG_FLASH_READ1         0x0001  /* 1 is standard                        */
+#define CFG_FLASH_READ2         0x0002  /* 2 is standard                        */
+
+#define CFG_FLASH_EMPTY_INFO            /* print 'E' for empty sector on flinfo */
+
+#if 0 /* test-only */
+#define CFG_JFFS2_FIRST_BANK    0           /* use for JFFS2 */
+#define CFG_JFFS2_NUM_BANKS     1           /* ! second bank contains U-Boot */
+#endif
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE		0x00000000
+#define CFG_FLASH_BASE		0xFFFC0000
+#define CFG_MONITOR_BASE	TEXT_BASE
+#define CFG_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB for Monitor	*/
+#define CFG_MALLOC_LEN		(256 * 1024)	/* Reserve 256 kB for malloc()	*/
+
+#if (CFG_MONITOR_BASE < FLASH_BASE0_PRELIM)
+# define CFG_RAMBOOT		1
+#else
+# undef CFG_RAMBOOT
+#endif
+
+/*-----------------------------------------------------------------------
+ * Environment Variable setup
+ */
+#define CFG_ENV_IS_IN_EEPROM    1       /* use EEPROM for environment vars */
+#define CFG_ENV_OFFSET          0x100   /* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE            0x700   /* 2048 bytes may be used for env vars*/
+				   /* total size of a CAT24WC16 is 2048 bytes */
+
+#define CFG_NVRAM_BASE_ADDR	0xF0000500		/* NVRAM base address	*/
+#define CFG_NVRAM_SIZE		242		        /* NVRAM size		*/
+
+/*-----------------------------------------------------------------------
+ * I2C EEPROM (CAT24WC16) for environment
+ */
+#define CONFIG_HARD_I2C			/* I2c with hardware support */
+#define CFG_I2C_SPEED		400000	/* I2C speed and slave address */
+#define CFG_I2C_SLAVE		0x7F
+
+#define CFG_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT24WC08		*/
+#if 0 /* test-only */
+/* CAT24WC08/16... */
+#define CFG_I2C_EEPROM_ADDR_LEN	1	/* Bytes of address		*/
+/* mask of address bits that overflow into the "EEPROM chip address"    */
+#define CFG_I2C_EEPROM_ADDR_OVERFLOW	0x07
+#define CFG_EEPROM_PAGE_WRITE_BITS 4	/* The Catalyst CAT24WC08 has	*/
+					/* 16 byte page write mode using*/
+					/* last	4 bits of the address	*/
+#else
+/* CAT24WC32/64... */
+#define CFG_I2C_EEPROM_ADDR_LEN	2	/* Bytes of address		*/
+/* mask of address bits that overflow into the "EEPROM chip address"    */
+#define CFG_I2C_EEPROM_ADDR_OVERFLOW	0x01
+#define CFG_EEPROM_PAGE_WRITE_BITS 5	/* The Catalyst CAT24WC32 has	*/
+					/* 32 byte page write mode using*/
+					/* last	5 bits of the address	*/
+#endif
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
+#define CFG_EEPROM_PAGE_WRITE_ENABLE
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_DCACHE_SIZE		16384	/* For IBM 405 CPUs, older 405 ppc's    */
+					/* have only 8kB, 16kB is save here     */
+#define CFG_CACHELINE_SIZE	32	/* ...			*/
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
+#endif
+
+/*-----------------------------------------------------------------------
+ * External Bus Controller (EBC) Setup
+ */
+
+#define CAN_BA          0xF0000000          /* CAN Base Address                 */
+#define DUART0_BA       0xF0000400          /* DUART Base Address               */
+#define DUART1_BA       0xF0000408          /* DUART Base Address               */
+#define RTC_BA          0xF0000500          /* RTC Base Address                 */
+#define VGA_BA          0xF1000000          /* Epson VGA Base Address           */
+#define CFG_NAND_BASE   0xF4000000          /* NAND FLASH Base Address          */
+
+/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization                       */
+#define CFG_EBC_PB0AP           0x92015480
+/*#define CFG_EBC_PB0AP           0x08055880  /XXX* TWT=16,CSN=1,OEN=1,WBN=1,WBF=1,TH=4,SOR=1 */
+#define CFG_EBC_PB0CR           0xFFC5A000  /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
+
+/* Memory Bank 1 (Flash Bank 1, NAND-FLASH) initialization                      */
+#define CFG_EBC_PB1AP           0x92015480
+#define CFG_EBC_PB1CR           0xF4018000  /* BAS=0xF40,BS=1MB,BU=R/W,BW=8bit  */
+
+/* Memory Bank 2 (8 Bit Peripheral: CAN, UART, RTC) initialization              */
+#define CFG_EBC_PB2AP           0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB2CR           0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit  */
+
+/* Memory Bank 3 (16 Bit Peripheral: FPGA internal, dig. IO) initialization     */
+#define CFG_EBC_PB3AP           0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB3CR           0xF011A000  /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
+
+/* Memory Bank 4 (Epson VGA) initialization                                     */
+#define CFG_EBC_PB4AP   0x03805380   /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=0 */
+#define CFG_EBC_PB4CR   VGA_BA | 0x7A000    /* BAS=0xF10,BS=8MB,BU=R/W,BW=16bit */
+
+/*-----------------------------------------------------------------------
+ * FPGA stuff
+ */
+
+#define CFG_FPGA_BASE_ADDR 0xF0100100       /* FPGA internal Base Address       */
+
+/* FPGA internal regs */
+#define CFG_FPGA_CTRL           0x000
+
+/* FPGA Control Reg */
+#define CFG_FPGA_CTRL_CF_RESET  0x0001
+#define CFG_FPGA_CTRL_WDI       0x0002
+#define CFG_FPGA_CTRL_PS2_RESET 0x0020
+
+#define CFG_FPGA_SPARTAN2       1           /* using Xilinx Spartan 2 now    */
+#define CFG_FPGA_MAX_SIZE       128*1024    /* 128kByte is enough for XC2S50E*/
+
+/* FPGA program pin configuration */
+#define CFG_FPGA_PRG            0x04000000  /* FPGA program pin (ppc output) */
+#define CFG_FPGA_CLK            0x02000000  /* FPGA clk pin (ppc output)     */
+#define CFG_FPGA_DATA           0x01000000  /* FPGA data pin (ppc output)    */
+#define CFG_FPGA_INIT           0x00010000  /* FPGA init pin (ppc input)     */
+#define CFG_FPGA_DONE           0x00008000  /* FPGA done pin (ppc input)     */
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in data cache)
+ */
+/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
+#define CFG_TEMP_STACK_OCM        1
+
+/* On Chip Memory location */
+#define CFG_OCM_DATA_ADDR	0xF8000000
+#define CFG_OCM_DATA_SIZE	0x1000
+#define CFG_INIT_RAM_ADDR	CFG_OCM_DATA_ADDR /* inside of SDRAM		*/
+#define CFG_INIT_RAM_END	CFG_OCM_DATA_SIZE /* End of used area in RAM	*/
+
+#define CFG_GBL_DATA_SIZE      128  /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET    (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET      CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Definitions for GPIO setup (PPC405EP specific)
+ *
+ * GPIO0[0]     - External Bus Controller BLAST output
+ * GPIO0[1-9]   - Instruction trace outputs -> GPIO
+ * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
+ * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs -> GPIO
+ * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
+ * GPIO0[24-27] - UART0 control signal inputs/outputs
+ * GPIO0[28-29] - UART1 data signal input/output
+ * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
+ */
+#define CFG_GPIO0_OSRH          0x40000550
+#define CFG_GPIO0_OSRL          0x00000110
+#define CFG_GPIO0_ISR1H         0x00000000
+#define CFG_GPIO0_ISR1L         0x15555445
+#define CFG_GPIO0_TSRH          0x00000000
+#define CFG_GPIO0_TSRL          0x00000000
+#define CFG_GPIO0_TCR           0xF7FE0014
+
+#define CFG_DUART_RST           (0x80000000 >> 14)
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
+#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
+
+/*
+ * Default speed selection (cpu_plb_opb_ebc) in mhz.
+ * This value will be set if iic boot eprom is disabled.
+ */
+#if 1
+#define PLLMR0_DEFAULT   PLLMR0_266_133_66_33
+#define PLLMR1_DEFAULT   PLLMR1_266_133_66_33
+#endif
+#if 0
+#define PLLMR0_DEFAULT   PLLMR0_200_100_50_33
+#define PLLMR1_DEFAULT   PLLMR1_200_100_50_33
+#endif
+#if 0
+#define PLLMR0_DEFAULT   PLLMR0_133_66_66_33
+#define PLLMR1_DEFAULT   PLLMR1_133_66_66_33
+#endif
+
+#endif	/* __CONFIG_H */

include/exports.h

@@ -18,6 +18,8 @@ void *malloc(size_t);
 void free(void*);
 void udelay(unsigned long);
 unsigned long get_timer(unsigned long);
+void vprintf(const char *, va_list);
+void do_reset (void);
 #if (CONFIG_COMMANDS & CFG_CMD_I2C)
 int i2c_write (uchar, uint, int , uchar* , int);
 int i2c_read (uchar, uint, int , uchar* , int);