* Modify KUP4X board configuration to use SL811 driver for USB memory

sticks (including FAT / VFAT filesystem support)

* Add SL811 Host Controller Interface driver for USB

* Add CFG_I2C_EEPROM_ADDR_OVERFLOW desription to README

* Patch by Pantelis Antoniou, 19 Apr 2004:
  Allow to use shell style syntax (i. e. ${var} ) with standard parser.
  Minor patches for Intracom boards.

* Patch by Christian Pell, 19 Apr 2004:
  cleanup support for CF/IDE on PCMCIA for PXA25X

CHANGELOG

@@ -1,7 +1,84 @@
 ======================================================================
 Changes for U-Boot 1.1.1:
 ======================================================================
- 
+
+* Modify KUP4X board configuration to use SL811 driver for USB memory
+  sticks (including FAT / VFAT filesystem support)
+
+* Add SL811 Host Controller Interface driver for USB
+
+* Add CFG_I2C_EEPROM_ADDR_OVERFLOW desription to README
+
+* Patch by Pantelis Antoniou, 19 Apr 2004:
+  Allow to use shell style syntax (i. e. ${var} ) with standard parser.
+  Minor patches for Intracom boards.
+
+* Patch by Christian Pell, 19 Apr 2004:
+  cleanup support for CF/IDE on PCMCIA for PXA25X
+
+* Temporarily disabled John Kerl's extended MII command code because
+  "miivals.h" is missing
+
+* Patches by Mark Jonas, 13 Apr 2004:
+  - Remove CS0 chip select timing setting from cpu/mpc5xxx/start.S
+  - Add sync instructions to IceCube SDRAM init code
+  - Move SDRAM chip constants into seperate include files
+  - Unify DDR and SDR initialization code
+  - Unify all IceCube (Lite5xxx) target names
+
+* Patch by John Kerl, 16 Apr 2004:
+  Enable ranges in mii command, e.g. mii read 0-1f 0 or
+  mii read 4-7 18-1a.  Also add mii dump subcommand for
+  pretty-printing standard regs 0-5.
+
+* Patch by  Stephen Williams, 16 April 2004:
+  fix typo in JSE.h; update MAINTAINERS
+
+* Patch by Matthew S. McClintock, 14 Apr 2004:
+  fix initdram function for utx8245 board
+
+* Patch by Markus Pietrek, 14 Apr 2004:
+  use ATAG_INITRD2 instead of deprecated ATAG_INITRD tag
+
+* Patch by Reinhard Meyer, 18 Apr 2004:
+  provide the IDE Reset Function for EMK 5200 boards
+
+* Patch by Masami Komiya, 12 Apr 2004:
+  fix pci_hose_write_config_{byte,word}_via_dword problems
+
+* Patch by Sangmoon Kim, 12 Apr 2004:
+  Update max RAM size for debris board
+
+* Patch by Travis Sawyer, 08 Apr 2004:
+  Add TLB entry for second DIMM slot on ocotea
+
+* Patch by Masami Komiya, 08 Apr 2004:
+  add RTL8169 network driver
+
+* Patch by Dan Malek, 07 Apr 2004:
+  - Add support for RPC/STx GP3, Motorola 8560 board
+  - Update 85xx TSEC driver so it searches MII for first available PHY
+    and uses that one.
+  - Add functions to support console MII commands.
+
+* Patch by Tolunay Orkun, 07 Apr 2004:
+  Move initialization of bi_iic_fast[]
+  from board_init_f() to board_init_r()
+
+* Patch by Yasushi Shoji, 07 Apr 2004:
+  Cleanup microblaze port
+
+* Patch by Sangmoon Kim, 07 Apr 2004:
+  Add auto SDRAM module detection for Debris board
+
+* Patch by Rune Torgersen, 06 Apr 2004:
+  - Fix some PCI problems on the MPC8266ADS board
+  - Fix the location of some PCI entries in the immap structure
+
+* Patch by Yasushi Shoji, 07 Apr 2004:
+  - add support for microblaze processors
+  - add support for AtmarkTechno "suzaku" board
+
 * Configure PPChameleon board to use redundand environment in flash
 
 * Configure PPChameleon board to use JFFS2 NAND support.

MAINTAINERS

@@ -255,6 +255,10 @@ Rune Torgersen <runet@innovsys.com>
 
 	MPC8266ADS		MPC8266
 
+Stephen Williams <steve@icarus.com>
+
+	JSE			PPC405GPr
+
 John Zhan <zhanz@sinovee.com>
 
 	svm_sc8xx		MPC8xx
@@ -264,6 +268,10 @@ Xianghua Xiao <x.xiao@motorola.com>
 	MPC8540ADS		MPC8540
 	MPC8560ADS		MPC8560
 
+Dan Malek <dan@embeddededge.com>
+
+	STxGP3			MPC85xx
+
 -------------------------------------------------------------------------
 
 Unknown / orphaned boards:

MAKEALL

@@ -25,7 +25,7 @@ LIST_5xx="	\
 #########################################################################
 
 LIST_5xxx="	\
-	IceCube_5100	IceCube_5200	EVAL5200	PM520		\
+	icecube_5100	icecube_5200	EVAL5200	PM520		\
 "
 
 #########################################################################
@@ -97,7 +97,7 @@ LIST_8260="	\
 #########################################################################
 
 LIST_85xx="	\
-	MPC8540ADS	MPC8560ADS					\
+	MPC8540ADS	MPC8560ADS	stxgp3				\
 "
 
 #########################################################################

Makefile

@@ -75,6 +75,9 @@ endif
 ifeq ($(ARCH),m68k)
 CROSS_COMPILE = m68k-elf-
 endif
+ifeq ($(ARCH),microblaze)
+CROSS_COMPILE = mb-
+endif
 endif
 endif
 
@@ -209,16 +212,16 @@ PATI_config:		unconfig
 #########################################################################
 ## MPC5xxx Systems
 #########################################################################
-MPC5200LITE_config		\
-MPC5200LITE_LOWBOOT_config	\
-MPC5200LITE_LOWBOOT08_config	\
-icecube_5200_DDR_config		\
-IceCube_5200_DDR_config		\
-icecube_5200_DDR_LOWBOOT_config \
-icecube_5200_DDR_LOWBOOT08_config \
-icecube_5200_config		\
-IceCube_5200_config		\
-IceCube_5100_config:		unconfig
+Lite5200_config				\
+Lite5200_LOWBOOT_config			\
+Lite5200_LOWBOOT08_config		\
+icecube_5200_config			\
+icecube_5200_LOWBOOT_config		\
+icecube_5200_LOWBOOT08_config		\
+icecube_5200_DDR_config 		\
+icecube_5200_DDR_LOWBOOT_config 	\
+icecube_5200_DDR_LOWBOOT08_config	\
+icecube_5100_config:			unconfig
 	@ >include/config.h
 	@[ -z "$(findstring LOWBOOT_,$@)" ] || \
 		{ if [ "$(findstring DDR,$@)" ] ; \
@@ -719,6 +722,9 @@ CPC45_ROMBOOT_config:	unconfig
 CU824_config: unconfig
 	@./mkconfig $(@:_config=) ppc mpc824x cu824
 
+debris_config: unconfig
+	@./mkconfig $(@:_config=) ppc mpc824x debris etin
+
 eXalion_config: unconfig
 	@./mkconfig $(@:_config=) ppc mpc824x eXalion
 
@@ -944,6 +950,9 @@ MPC8540ADS_config:      unconfig
 MPC8560ADS_config:      unconfig
 	@./mkconfig $(@:_config=) ppc mpc85xx mpc8560ads
 
+stxgp3_config:      unconfig
+	@./mkconfig $(@:_config=) ppc mpc85xx stxgp3
+
 #########################################################################
 ## 74xx/7xx Systems
 #########################################################################
@@ -960,9 +969,6 @@ DB64360_config:  unconfig
 DB64460_config:  unconfig
 	@./mkconfig DB64460 ppc 74xx_7xx db64460 Marvell
 
-debris_config: unconfig
-	@./mkconfig $(@:_config=) ppc mpc824x debris etin
-
 ELPPC_config: unconfig
 	@./mkconfig $(@:_config=) ppc 74xx_7xx elppc eltec
 
@@ -1250,6 +1256,17 @@ ADNPESC1_config: unconfig
 	@./mkconfig -a ADNPESC1 nios nios adnpesc1 ssv
 
 
+#========================================================================
+# MicroBlaze
+#========================================================================
+#########################################################################
+## Microblaze
+#########################################################################
+suzaku_config:	unconfig
+	@ >include/config.h
+	@echo "#define CONFIG_SUZAKU 1" >> include/config.h
+	@./mkconfig -a $(@:_config=) microblaze microblaze suzaku AtmarkTechno
+
 #########################################################################
 ## MIPS32 AU1X00
 #########################################################################

README

@@ -240,6 +240,10 @@ The following options need to be configured:
 		CONFIG_ARM7
 		CONFIG_PXA250
 
+		MicroBlaze based CPUs:
+		----------------------
+		CONFIG_MICROBLZE
+
 
 - Board Type:	Define exactly one of
 
@@ -277,11 +281,11 @@ The following options need to be configured:
 		CONFIG_RPXlite,		CONFIG_RPXsuper,	CONFIG_rsdproto,
 		CONFIG_sacsng,		CONFIG_Sandpoint8240,	CONFIG_Sandpoint8245,
 		CONFIG_sbc8260,		CONFIG_SM850,		CONFIG_SPD823TS,
-		CONFIG_SXNI855T,	CONFIG_TQM823L,		CONFIG_TQM8260,
-		CONFIG_TQM850L,		CONFIG_TQM855L,		CONFIG_TQM860L,
-		CONFIG_TTTech,		CONFIG_UTX8245,		CONFIG_V37,
-		CONFIG_W7OLMC,		CONFIG_W7OLMG,		CONFIG_WALNUT405,
-		CONFIG_ZPC1900,		CONFIG_ZUMA,
+		CONFIG_STXGP3,		CONFIG_SXNI855T,	CONFIG_TQM823L,
+		CONFIG_TQM8260,		CONFIG_TQM850L,		CONFIG_TQM855L,
+		CONFIG_TQM860L,		CONFIG_TTTech,		CONFIG_UTX8245,
+		CONFIG_V37,		CONFIG_W7OLMC,		CONFIG_W7OLMG,
+		CONFIG_WALNUT405,	CONFIG_ZPC1900,		CONFIG_ZUMA,
 
 		ARM based boards:
 		-----------------
@@ -292,6 +296,11 @@ The following options need to be configured:
 		CONFIG_LUBBOCK,			CONFIG_SHANNON,		CONFIG_SMDK2400,
 		CONFIG_SMDK2410,		CONFIG_TRAB,		CONFIG_VCMA9,
 
+		MicroBlaze based boards:
+		------------------------
+
+		CONFIG_SUZAKU
+
 
 - CPU Module Type: (if CONFIG_COGENT is defined)
 		Define exactly one of
@@ -1742,6 +1751,17 @@ to save the current settings.
 	  The length in bytes of the EEPROM memory array address.  Note
 	  that this is NOT the chip address length!
 
+	- CFG_I2C_EEPROM_ADDR_OVERFLOW:
+	  EEPROM chips that implement "address overflow" are ones
+	  like Catalyst 24WC04/08/16 which has 9/10/11 bits of
+	  address and the extra bits end up in the "chip address" bit
+	  slots. This makes a 24WC08 (1Kbyte) chip look like four 256
+	  byte chips.
+
+	  Note that we consider the length of the address field to
+	  still be one byte because the extra address bits are hidden
+	  in the chip address.
+
 	- CFG_EEPROM_SIZE:
 	  The size in bytes of the EEPROM device.
 
@@ -1963,6 +1983,16 @@ Low Level (hardware related) configuration options:
 		Note that this is a global option, we can't
 		have one FEC in standard MII mode and another in RMII mode.
 
+- CONFIG_CRC32_VERIFY
+		Add a verify option to the crc32 command.
+		The syntax is:
+
+		=> crc32 -v <address> <count> <crc32>
+
+		Where address/count indicate a memory area
+		and crc32 is the correct crc32 which the
+		area should have.
+
 Building the Software:
 ======================
 
@@ -2008,9 +2038,9 @@ configurations; the following names are supported:
 	QS850_config		QS860T_config		RPXlite_config
 	RPXsuper_config		rsdproto_config		Sandpoint8240_config
 	sbc8260_config		SM850_config		SPD823TS_config
-	SXNI855T_config		TQM823L_config		TQM850L_config
-	TQM855L_config		TQM860L_config		WALNUT405_config
-	ZPC1900_config
+	stxgp3_config		SXNI855T_config		TQM823L_config
+	TQM850L_config		TQM855L_config		TQM860L_config
+	WALNUT405_config	ZPC1900_config
 
 	Note: for some board special configuration names may exist; check  if
 	      additional  information is available from the board vendor; for

board/AtmarkTechno/suzaku/Makefile

@@ -0,0 +1,40 @@
+#
+# (C) Copyright 2003
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	= $(BOARD).o flash.o
+
+$(LIB):	.depend $(OBJS)
+	$(AR) crv $@ $(OBJS)
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+sinclude .depend
+
+#########################################################################

board/AtmarkTechno/suzaku/config.mk

@@ -0,0 +1,29 @@
+#
+# (C) Copyright 2004 Atmark Techno, Inc.
+#
+# Yasushi SHOJI <yashi@atmark-techno.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+TEXT_BASE = 0x80F00000
+
+PLATFORM_CPPFLAGS += -mno-xl-soft-mul
+PLATFORM_CPPFLAGS += -mno-xl-soft-div
+PLATFORM_CPPFLAGS += -mxl-barrel-shift

board/AtmarkTechno/suzaku/flash.c

@@ -0,0 +1,46 @@
+/*
+ * (C) Copyright 2004 Atmark Techno, Inc.
+ *
+ * Yasushi SHOJI <yashi@atmark-techno.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+
+flash_info_t flash_info[CFG_MAX_FLASH_BANKS];
+
+unsigned long flash_init(void)
+{
+	return 0;
+}
+
+void flash_print_info(flash_info_t *info)
+{
+}
+
+int flash_erase(flash_info_t *info, int s_first, int s_last)
+{
+	return 0;
+}
+
+int write_buff(flash_info_t *info, uchar *src, ulong addr, ulong cnt)
+{
+	return 0;
+}

board/AtmarkTechno/suzaku/suzaku.c

@@ -0,0 +1,29 @@
+/*
+ * (C) Copyright 2004 Atmark Techno, Inc.
+ *
+ * Yasushi SHOJI <yashi@atmark-techno.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+
+void do_reset(void)
+{
+}

board/AtmarkTechno/suzaku/u-boot.lds

@@ -0,0 +1,65 @@
+/*
+ * (C) Copyright 2004 Atmark Techno, Inc.
+ *
+ * Yasushi SHOJI <yashi@atmark-techno.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(microblaze)
+ENTRY(_start)
+
+SECTIONS
+{
+	.text ALIGN(0x4):
+	{
+		__text_start = .;
+		cpu/microblaze/start.o (.text)
+		*(.text)
+		__text_end = .;
+	}
+
+	.rodata ALIGN(0x4):
+	{
+		__rodata_start = .;
+		*(.rodata)
+		__rodata_end = .;
+	}
+
+	.data ALIGN(0x4):
+	{
+		__data_start = .;
+		*(.data)
+		__data_end = .;
+	}
+
+	.u_boot_cmd ALIGN(0x4):
+	{
+		__u_boot_cmd_start = .;
+		*(.u_boot_cmd)
+		__u_boot_cmd_end = .;
+	}
+
+	.bss ALIGN(0x4):
+	{
+		__bss_start = .;
+		*(.bss)
+		__bss_start = .;
+	}
+}

board/dave/PPChameleonEVB/u-boot.lds

@@ -141,7 +141,7 @@ SECTIONS
   }
 
   . = 0xFFFF8000;
-  .ppcenv : 
+  .ppcenv :
   {
     common/environment.o(.ppcenv);
   }

board/emk/top5200/top5200.c

@@ -182,21 +182,29 @@ void pci_init_board(void)
 #endif
 
 /*****************************************************************************
- * provide the PCI Reset Function
+ * provide the IDE Reset Function
  *****************************************************************************/
-#ifdef CFG_CMD_IDE
-#define GPIO_PSC1_4	0x01000000ul
+#if defined (CFG_CMD_IDE) && defined (CONFIG_IDE_RESET)
+
+#define GPIO_PSC1_4	0x01000000UL
+
+void init_ide_reset (void)
+{
+	debug ("init_ide_reset\n");
+
+    	/* Configure PSC1_4 as GPIO output for ATA reset */
+	*(vu_long *) MPC5XXX_WU_GPIO_ENABLE |= GPIO_PSC1_4;
+	*(vu_long *) MPC5XXX_WU_GPIO_DIR    |= GPIO_PSC1_4;
+}
+
 void ide_set_reset (int idereset)
 {
+	debug ("ide_reset(%d)\n", idereset);
+
 	if (idereset) {
 		*(vu_long *) MPC5XXX_WU_GPIO_DATA &= ~GPIO_PSC1_4;
 	} else {
-		*(vu_long *) MPC5XXX_WU_GPIO_DATA |= GPIO_PSC1_4;
+		*(vu_long *) MPC5XXX_WU_GPIO_DATA |=  GPIO_PSC1_4;
 	}
-
-	/* Configure PSC1_4 as GPIO output for ATA reset */
-	/* (it does not matter we do this every time) */
-	*(vu_long *) MPC5XXX_WU_GPIO_ENABLE |= GPIO_PSC1_4;
-	*(vu_long *) MPC5XXX_WU_GPIO_DIR |= GPIO_PSC1_4;
 }
-#endif
+#endif /* defined (CFG_CMD_IDE) && defined (CONFIG_IDE_RESET) */

board/etin/debris/debris.c

@@ -24,6 +24,7 @@
 #include <common.h>
 #include <mpc824x.h>
 #include <pci.h>
+#include <i2c.h>
 
 int checkboard (void)
 {
@@ -52,28 +53,70 @@ int checkflash (void)
 
 long int initdram (int board_type)
 {
-	long size;
-#if 0
-	long new_bank0_end;
-	long mear1;
-	long emear1;
-#endif
+	int m, row, col, bank, i;
+	unsigned long start, end;
+	uint32_t mccr1;
+	uint32_t mear1 = 0, emear1 = 0, msar1 = 0, emsar1 = 0;
+	uint32_t mear2 = 0, emear2 = 0, msar2 = 0, emsar2 = 0;
+	uint8_t mber = 0;
 
-	size = get_ram_size(CFG_SDRAM_BASE, CFG_MAX_RAM_SIZE);
+	i2c_init(CFG_I2C_SPEED, CFG_I2C_SLAVE);
 
-#if 0
-	new_bank0_end = size - 1;
-	mear1 = mpc824x_mpc107_getreg(MEAR1);
-	emear1 = mpc824x_mpc107_getreg(EMEAR1);
-	mear1 = (mear1  & 0xFFFFFF00) |
-		((new_bank0_end & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT);
-	emear1 = (emear1 & 0xFFFFFF00) |
-		((new_bank0_end & MICR_ADDR_MASK) >> MICR_EADDR_SHIFT);
-	mpc824x_mpc107_setreg(MEAR1, mear1);
-	mpc824x_mpc107_setreg(EMEAR1, emear1);
-#endif
+	if (i2c_reg_read (0x50, 2) != 0x04) return 0;	/* Memory type */
+	m = i2c_reg_read (0x50, 5);	/* # of physical banks */
+	row = i2c_reg_read (0x50, 3);	/* # of rows */
+	col = i2c_reg_read (0x50, 4);	/* # of columns */
+	bank = i2c_reg_read (0x50, 17);	/* # of logical banks */
 
-	return (size);
+	CONFIG_READ_WORD(MCCR1, mccr1);
+	mccr1 &= 0xffff0000;
+
+	start = CFG_SDRAM_BASE;
+	end = start + (1 << (col + row + 3) ) * bank - 1;
+
+	for (i = 0; i < m; i++) {
+		mccr1 |= ((row == 13)? 2 : (bank == 4)? 0 : 3) << i * 2;
+		if (i < 4) {
+			msar1  |= ((start >> 20) & 0xff) << i * 8;
+			emsar1 |= ((start >> 28) & 0xff) << i * 8;
+			mear1  |= ((end >> 20) & 0xff) << i * 8;
+			emear1 |= ((end >> 28) & 0xff) << i * 8;
+		} else {
+			msar2  |= ((start >> 20) & 0xff) << (i-4) * 8;
+			emsar2 |= ((start >> 28) & 0xff) << (i-4) * 8;
+			mear2  |= ((end >> 20) & 0xff) << (i-4) * 8;
+			emear2 |= ((end >> 28) & 0xff) << (i-4) * 8;
+		}
+		mber |= 1 << i;
+		start += (1 << (col + row + 3) ) * bank;
+		end += (1 << (col + row + 3) ) * bank;
+	}
+	for (; i < 8; i++) {
+		if (i < 4) {
+			msar1  |= 0xff << i * 8;
+			emsar1 |= 0x30 << i * 8;
+			mear1  |= 0xff << i * 8;
+			emear1 |= 0x30 << i * 8;
+		} else {
+			msar2  |= 0xff << (i-4) * 8;
+			emsar2 |= 0x30 << (i-4) * 8;
+			mear2  |= 0xff << (i-4) * 8;
+			emear2 |= 0x30 << (i-4) * 8;
+		}
+	}
+
+	CONFIG_WRITE_WORD(MCCR1, mccr1);
+	CONFIG_WRITE_WORD(MSAR1, msar1);
+	CONFIG_WRITE_WORD(EMSAR1, emsar1);
+	CONFIG_WRITE_WORD(MEAR1, mear1);
+	CONFIG_WRITE_WORD(EMEAR1, emear1);
+	CONFIG_WRITE_WORD(MSAR2, msar2);
+	CONFIG_WRITE_WORD(EMSAR2, emsar2);
+	CONFIG_WRITE_WORD(MEAR2, mear2);
+	CONFIG_WRITE_WORD(EMEAR2, emear2);
+	CONFIG_WRITE_BYTE(MBER, mber);
+
+	return (1 << (col + row + 3) ) * bank * m;
 }
 
 /*

board/icecube/icecube.c

@@ -2,6 +2,9 @@
  * (C) Copyright 2003
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
+ * (C) Copyright 2004
+ * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
+ *
  * See file CREDITS for list of people who contributed to this
  * project.
  *
@@ -25,90 +28,84 @@
 #include <mpc5xxx.h>
 #include <pci.h>
 
+#if defined(CONFIG_MPC5200_DDR)
+#include "mt46v16m16-75.h"
+#else
+#include "mt48lc16m16a2-75.h"
+#endif
+
 #ifndef CFG_RAMBOOT
 static void sdram_start (int hi_addr)
 {
 	long hi_addr_bit = hi_addr ? 0x01000000 : 0;
 
-#ifdef CONFIG_MPC5200_DDR
 	/* unlock mode register */
-	*(vu_long *)MPC5XXX_SDRAM_CTRL = 0xf05f0f00 | hi_addr_bit;
+	*(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000000 | hi_addr_bit;
+	__asm__ volatile ("sync");
+
 	/* precharge all banks */
-	*(vu_long *)MPC5XXX_SDRAM_CTRL = 0xf05f0f02 | hi_addr_bit;
+	*(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000002 | hi_addr_bit;
+	__asm__ volatile ("sync");
+
+#if SDRAM_DDR
 	/* set mode register: extended mode */
-	*(vu_long *)MPC5XXX_SDRAM_MODE = 0x40090000;
+	*(vu_long *)MPC5XXX_SDRAM_MODE = SDRAM_EMODE;
+	__asm__ volatile ("sync");
+
 	/* set mode register: reset DLL */
-	*(vu_long *)MPC5XXX_SDRAM_MODE = 0x058d0000;
-	/* precharge all banks */
-	*(vu_long *)MPC5XXX_SDRAM_CTRL = 0xf05f0f02 | hi_addr_bit;
-	/* auto refresh */
-	*(vu_long *)MPC5XXX_SDRAM_CTRL = 0xf05f0f04 | hi_addr_bit;
-	/* set mode register */
-	*(vu_long *)MPC5XXX_SDRAM_MODE = 0x018d0000;
-	/* normal operation */
-	*(vu_long *)MPC5XXX_SDRAM_CTRL = 0x705f0f00 | hi_addr_bit;
-#else
-	/* unlock mode register */
-	*(vu_long *)MPC5XXX_SDRAM_CTRL = 0xd04f0000 | hi_addr_bit;
-	/* precharge all banks */
-	*(vu_long *)MPC5XXX_SDRAM_CTRL = 0xd04f0002 | hi_addr_bit;
-	/* set mode register */
-#if defined(CONFIG_MPC5200)
-	*(vu_long *)MPC5XXX_SDRAM_MODE = 0x00cd0000;
-#elif defined(CONFIG_MGT5100)
-	*(vu_long *)MPC5XXX_SDRAM_MODE = 0x008d0000;
+	*(vu_long *)MPC5XXX_SDRAM_MODE = SDRAM_MODE | 0x04000000;
+	__asm__ volatile ("sync");
 #endif
+
+	/* precharge all banks */
+	*(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000002 | hi_addr_bit;
+	__asm__ volatile ("sync");
+
 	/* auto refresh */
-	*(vu_long *)MPC5XXX_SDRAM_CTRL = 0xd04f0004 | hi_addr_bit;
-	/* auto refresh */
-	*(vu_long *)MPC5XXX_SDRAM_CTRL = 0xd04f0004 | hi_addr_bit;
+	*(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000004 | hi_addr_bit;
+	__asm__ volatile ("sync");
+
 	/* set mode register */
-	*(vu_long *)MPC5XXX_SDRAM_MODE = 0x00cd0000;
+	*(vu_long *)MPC5XXX_SDRAM_MODE = SDRAM_MODE;
+	__asm__ volatile ("sync");
+
 	/* normal operation */
-	*(vu_long *)MPC5XXX_SDRAM_CTRL = 0x504f0000 | hi_addr_bit;
-#endif
+	*(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | hi_addr_bit;
+	__asm__ volatile ("sync");
 }
 #endif
 
+/*
+ * ATTENTION: Although partially referenced initdram does NOT make real use
+ *            use of CFG_SDRAM_BASE. The code does not work if CFG_SDRAM_BASE
+ *            is something else than 0x00000000.
+ */
+
+#if defined(CONFIG_MPC5200)
 long int initdram (int board_type)
 {
 	ulong dramsize = 0;
-#ifdef CONFIG_MPC5200_DDR
 	ulong dramsize2 = 0;
-#endif
 #ifndef CFG_RAMBOOT
 	ulong test1, test2;
 
-	/* configure SDRAM start/end */
-#if defined(CONFIG_MPC5200)
+	/* setup SDRAM chip selects */
 	*(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0x0000001e;/* 2G at 0x0 */
 	*(vu_long *)MPC5XXX_SDRAM_CS1CFG = 0x80000000;/* disabled */
+	__asm__ volatile ("sync");
 
-#ifdef CONFIG_MPC5200_DDR
 	/* setup config registers */
-	*(vu_long *)MPC5XXX_SDRAM_CONFIG1 = 0x73722930;
-	*(vu_long *)MPC5XXX_SDRAM_CONFIG2 = 0x47770000;
+	*(vu_long *)MPC5XXX_SDRAM_CONFIG1 = SDRAM_CONFIG1;
+	*(vu_long *)MPC5XXX_SDRAM_CONFIG2 = SDRAM_CONFIG2;
+	__asm__ volatile ("sync");
 
-	/* set tap delay to 0x10 */
-	*(vu_long *)MPC5XXX_CDM_PORCFG = 0x10000000;
-#else
-	/* setup config registers */
-	*(vu_long *)MPC5XXX_SDRAM_CONFIG1 = 0xd2322800;
-	*(vu_long *)MPC5XXX_SDRAM_CONFIG2 = 0x8ad70000;
+#if SDRAM_DDR
+	/* set tap delay */
+	*(vu_long *)MPC5XXX_CDM_PORCFG = SDRAM_TAPDELAY;
+	__asm__ volatile ("sync");
 #endif
 
-#elif defined(CONFIG_MGT5100)
-	*(vu_long *)MPC5XXX_SDRAM_START = 0x00000000;
-	*(vu_long *)MPC5XXX_SDRAM_STOP = 0x0000ffff;/* 2G */
-	*(vu_long *)MPC5XXX_ADDECR |= (1 << 22); /* Enable SDRAM */
-
-	/* setup config registers */
-	*(vu_long *)MPC5XXX_SDRAM_CONFIG1 = 0xc2222600;
-	*(vu_long *)MPC5XXX_SDRAM_CONFIG2 = 0x88b70004;
-
-	/* address select register */
-	*(vu_long *)MPC5XXX_SDRAM_XLBSEL = 0x03000000;
-#endif
+	/* find RAM size using SDRAM CS0 only */
 	sdram_start(0);
 	test1 = get_ram_size((ulong *)CFG_SDRAM_BASE, 0x80000000);
 	sdram_start(1);
@@ -119,11 +116,23 @@ long int initdram (int board_type)
 	} else {
 		dramsize = test2;
 	}
-#if defined(CONFIG_MPC5200)
-	*(vu_long *)MPC5XXX_SDRAM_CS0CFG =
-		(0x13 + __builtin_ffs(dramsize >> 20) - 1);
-#ifdef CONFIG_MPC5200_DDR
+
+	/* memory smaller than 1MB is impossible */
+	if (dramsize < (1 << 20)) {
+		dramsize = 0;
+	}
+
+	/* set SDRAM CS0 size according to the amount of RAM found */
+	if (dramsize > 0) {
+		*(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0x13 + __builtin_ffs(dramsize >> 20) - 1;
+	} else {
+		*(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0; /* disabled */
+	}
+
+	/* let SDRAM CS1 start right after CS0 */
 	*(vu_long *)MPC5XXX_SDRAM_CS1CFG = dramsize + 0x0000001e;/* 2G */
+
+	/* find RAM size using SDRAM CS1 only */
 	sdram_start(0);
 	test1 = get_ram_size((ulong *)(CFG_SDRAM_BASE + dramsize), 0x80000000);
 	sdram_start(1);
@@ -134,34 +143,94 @@ long int initdram (int board_type)
 	} else {
 		dramsize2 = test2;
 	}
-	*(vu_long *)MPC5XXX_SDRAM_CS1CFG =
-		dramsize + (0x13 + __builtin_ffs(dramsize2 >> 20) - 1);
-#else
-	*(vu_long *)MPC5XXX_SDRAM_CS1CFG = dramsize; /* disabled */
-#endif
-#elif defined(CONFIG_MGT5100)
-	*(vu_long *)MPC5XXX_SDRAM_STOP = ((dramsize - 1) >> 15);
-#endif
 
-#else	/* CFG_RAMBOOT */
-#ifdef CONFIG_MGT5100
-	*(vu_long *)MPC5XXX_ADDECR |= (1 << 22); /* Enable SDRAM */
-	dramsize = ((*(vu_long *)MPC5XXX_SDRAM_STOP + 1) << 15);
-#else
-	dramsize = ((1 << (*(vu_long *)MPC5XXX_SDRAM_CS0CFG - 0x13)) << 20);
-#ifdef CONFIG_MPC5200_DDR
-	dramsize2 = ((1 << (*(vu_long *)MPC5XXX_SDRAM_CS1CFG - 0x13)) << 20);
-#endif
-#endif
+	/* memory smaller than 1MB is impossible */
+	if (dramsize2 < (1 << 20)) {
+		dramsize2 = 0;
+	}
+
+	/* set SDRAM CS1 size according to the amount of RAM found */
+	if (dramsize2 > 0) {
+		*(vu_long *)MPC5XXX_SDRAM_CS1CFG = dramsize
+			| (0x13 + __builtin_ffs(dramsize2 >> 20) - 1);
+	} else {
+		*(vu_long *)MPC5XXX_SDRAM_CS1CFG = dramsize; /* disabled */
+	}
+
+#else /* CFG_RAMBOOT */
+
+	/* retrieve size of memory connected to SDRAM CS0 */
+	dramsize = *(vu_long *)MPC5XXX_SDRAM_CS0CFG & 0xFF;
+	if (dramsize >= 0x13) {
+		dramsize = (1 << (dramsize - 0x13)) << 20;
+	} else {
+		dramsize = 0;
+	}
+
+	/* retrieve size of memory connected to SDRAM CS1 */
+	dramsize2 = *(vu_long *)MPC5XXX_SDRAM_CS1CFG & 0xFF;
+	if (dramsize2 >= 0x13) {
+		dramsize2 = (1 << (dramsize2 - 0x13)) << 20;
+	} else {
+		dramsize2 = 0;
+	}
+
+#endif /* CFG_RAMBOOT */
+
+	return dramsize + dramsize2;
+}
+
+#elif defined(CONFIG_MGT5100)
+
+long int initdram (int board_type)
+{
+	ulong dramsize = 0;
+#ifndef CFG_RAMBOOT
+	ulong test1, test2;
+
+	/* setup and enable SDRAM chip selects */
+	*(vu_long *)MPC5XXX_SDRAM_START = 0x00000000;
+	*(vu_long *)MPC5XXX_SDRAM_STOP = 0x0000ffff;/* 2G */
+	*(vu_long *)MPC5XXX_ADDECR |= (1 << 22); /* Enable SDRAM */
+	__asm__ volatile ("sync");
+
+	/* setup config registers */
+	*(vu_long *)MPC5XXX_SDRAM_CONFIG1 = SDRAM_CONFIG1;
+	*(vu_long *)MPC5XXX_SDRAM_CONFIG2 = SDRAM_CONFIG2;
+
+	/* address select register */
+	*(vu_long *)MPC5XXX_SDRAM_XLBSEL = SDRAM_ADDRSEL;
+	__asm__ volatile ("sync");
+
+	/* find RAM size */
+	sdram_start(0);
+	test1 = get_ram_size((ulong *)CFG_SDRAM_BASE, 0x80000000);
+	sdram_start(1);
+	test2 = get_ram_size((ulong *)CFG_SDRAM_BASE, 0x80000000);
+	if (test1 > test2) {
+		sdram_start(0);
+		dramsize = test1;
+	} else {
+		dramsize = test2;
+	}
+
+	/* set SDRAM end address according to size */
+	*(vu_long *)MPC5XXX_SDRAM_STOP = ((dramsize - 1) >> 15);
+
+#else /* CFG_RAMBOOT */
+
+	/* Retrieve amount of SDRAM available */
+	dramsize = ((*(vu_long *)MPC5XXX_SDRAM_STOP + 1) << 15);
+
 #endif /* CFG_RAMBOOT */
 
-#ifdef CONFIG_MPC5200_DDR
-	dramsize += dramsize2;
-#endif
-	/* return total ram size */
 	return dramsize;
 }
 
+#else
+#error Neither CONFIG_MPC5200 or CONFIG_MGT5100 defined
+#endif
+
 int checkboard (void)
 {
 #if defined(CONFIG_MPC5200)

board/icecube/mt46v16m16-75.h

@@ -0,0 +1,37 @@
+/*
+ * (C) Copyright 2004
+ * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#define SDRAM_DDR	1		/* is DDR */
+
+#if defined(CONFIG_MPC5200)
+/* Settings for XLB = 132 MHz */
+#define SDRAM_MODE	0x018D0000
+#define SDRAM_EMODE	0x40090000
+#define SDRAM_CONTROL	0x705f0f00
+#define SDRAM_CONFIG1	0x73722930
+#define SDRAM_CONFIG2	0x47770000
+#define SDRAM_TAPDELAY	0x10000000
+
+#else
+#error CONFIG_MPC5200 not defined
+#endif

board/icecube/mt48lc16m16a2-75.h

@@ -0,0 +1,43 @@
+/*
+ * (C) Copyright 2004
+ * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#define SDRAM_DDR	0		/* is SDR */
+
+#if defined(CONFIG_MPC5200)
+/* Settings for XLB = 132 MHz */
+#define SDRAM_MODE	0x00CD0000
+#define SDRAM_CONTROL	0x504F0000
+#define SDRAM_CONFIG1	0xD2322800
+#define SDRAM_CONFIG2	0x8AD70000
+
+#elif defined(CONFIG_MGT5100)
+/* Settings for XLB = 66 MHz */
+#define SDRAM_MODE	0x008D0000
+#define SDRAM_CONTROL	0x504F0000
+#define SDRAM_CONFIG1	0xC2222600
+#define SDRAM_CONFIG2	0x88B70004
+#define SDRAM_ADDRSEL	0x02000000
+
+#else
+#error Neither CONFIG_MPC5200 or CONFIG_MGT5100 defined
+#endif

board/kup/kup4x/Makefile

@@ -25,7 +25,7 @@ include $(TOPDIR)/config.mk
 
 LIB	= lib$(BOARD).a
 
-OBJS	= $(BOARD).o ../common/flash.o ../common/kup.o usb.o
+OBJS	= $(BOARD).o ../common/flash.o ../common/kup.o
 
 $(LIB):	.depend $(OBJS)
 	$(AR) crv $@ $(OBJS)

board/kup/kup4x/usb.c

@@ -1,81 +0,0 @@
-/*
- * (C) Copyright 2004
- * Klaus Heydeck, Kieback & Peter GmbH & Co KG, heydeck@kieback-peter.de
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <mpc8xx.h>
-#include "../common/kup.h"
-
-
-#define  SL811_ADR (0x50000000)
-#define  SL811_DAT (0x50000001)
-
-
-static void sl811_write_index_data (__u8 index, __u8 data)
-{
-	*(volatile unsigned char *) (SL811_ADR) = index;
-	__asm__ ("eieio");
-	*(volatile unsigned char *) (SL811_DAT) = data;
-	__asm__ ("eieio");
-}
-
-static __u8 sl811_read_index_data (__u8 index)
-{
-	__u8 data;
-
-	*(volatile unsigned char *) (SL811_ADR) = index;
-	__asm__ ("eieio");
-	data = *(volatile unsigned char *) (SL811_DAT);
-	__asm__ ("eieio");
-	return (data);
-}
-
-int usb_init_kup4x (void)
-{
-	volatile immap_t *immap = (immap_t *) CFG_IMMR;
-	volatile memctl8xx_t *memctl = &immap->im_memctl;
-	int i;
-	unsigned char tmp;
-
-	memctl = &immap->im_memctl;
-	memctl->memc_or7 = 0xFFFF8726;
-	memctl->memc_br7 = 0x50000401;	/* start at 0x50000000 */
-	/* BP 14 low = USB ON */
-	immap->im_cpm.cp_pbdat &= ~(BP_USB_VCC);
-	/* PB 14 nomal port */
-	immap->im_cpm.cp_pbpar &= ~(BP_USB_VCC);
-	/* output */
-	immap->im_cpm.cp_pbdir |= (BP_USB_VCC);
-
-	puts ("USB:   ");
-
-	for (i = 0x10; i < 0xff; i++) {
-		sl811_write_index_data (i, i);
-		tmp = (sl811_read_index_data (i));
-		if (tmp != i) {
-			printf ("SL811 compare error index=0x%02x read=0x%02x\n", i, tmp);
-			return (-1);
-		}
-	}
-	printf ("SL811 ready\n");
-	return (0);
-}

board/netphone/netphone.c

@@ -30,6 +30,7 @@
 #include <common.h>
 #include <miiphy.h>
 #include <sed156x.h>
+#include <status_led.h>
 
 #include "mpc8xx.h"
 
@@ -659,6 +660,7 @@ int overwrite_console(void)
 
 extern int drv_phone_init(void);
 extern int drv_phone_use_me(void);
+extern int drv_phone_is_idle(void);
 
 int misc_init_r(void)
 {
@@ -691,6 +693,12 @@ int last_stage_init(void)
 		do_poll();
 
 		if (drv_phone_use_me()) {
+			status_led_set(0, STATUS_LED_ON);
+			while (!drv_phone_is_idle()) {
+				do_poll();
+				udelay(1000000 / CFG_HZ);
+			}
+
 			console_assign(stdin, "phone");
 			console_assign(stdout, "phone");
 			console_assign(stderr, "phone");

board/netphone/phone_console.c

@@ -179,7 +179,6 @@ static int last_input_mode;
 static int refresh_time;
 static int blink_time;
 static char last_fast_punct;
-static int last_tab_indicator = -1;
 
 /*************************************************************************************************/
 
@@ -239,8 +238,6 @@ static void console_init(void)
 	refresh_time = REFRESH_HZ;
 	blink_time = BLINK_HZ;
 
-	tab_indicator = 1;
-
 	memset(vty_buf, ' ', sizeof(vty_buf));
 
 	memset(last_visible_buf, ' ', sizeof(last_visible_buf));
@@ -253,6 +250,8 @@ static void console_init(void)
 	sed156x_init();
 	width = sed156x_text_width;
 	height = sed156x_text_height - 1;
+
+	tab_indicator = 0;
 }
 
 /*****************************************************************************/
@@ -718,8 +717,10 @@ static void update(void)
 	if (input_mode != last_input_mode)
 		sed156x_output_at(sed156x_text_width - 3, sed156x_text_height - 1, input_mode_txt[input_mode], 3);
 
-	if (tab_indicator != last_tab_indicator)
+	if (tab_indicator == 0) {
 		sed156x_output_at(0, sed156x_text_height - 1, "\\t", 2);
+		tab_indicator = 1;
+	}
 
 	if (fast_punct != last_fast_punct)
 		sed156x_output_at(4, sed156x_text_height - 1, &fast_punct, 1);
@@ -779,7 +780,6 @@ static void update(void)
 
 	last_input_mode = input_mode;
 	last_fast_punct = fast_punct;
-	last_tab_indicator = tab_indicator;
 }
 
 /* ensure visibility; the trick is to minimize the screen movement */
@@ -891,7 +891,8 @@ void phone_putc(const char c)
 	blink_time = BLINK_HZ;
 
 	switch (c) {
-		case 13:		/* ignore */
+		case '\a':		/* ignore bell            */
+		case '\r':		/* ignore carriage return */
 			break;
 
 		case '\n':		/* next line */
@@ -1141,3 +1142,10 @@ static void kp_do_poll(void)
 			break;
 	}
 }
+
+/**************************************************************************************/
+
+int drv_phone_is_idle(void)
+{
+	return kp_state == SCAN;
+}

board/ocotea/init.S

@@ -91,6 +91,7 @@ tlbtab:
     tlbentry( CFG_ISRAM_BASE, SZ_4K, 0x80000000, 0, AC_R|AC_W|AC_X )
     tlbentry( CFG_ISRAM_BASE + 0x1000, SZ_4K, 0x80001000, 0, AC_R|AC_W|AC_X )
     tlbentry( CFG_SDRAM_BASE, SZ_256M, 0x00000000, 0, AC_R|AC_W|AC_X|SA_G|SA_I )
+    tlbentry( CFG_SDRAM_BASE+0x10000000, SZ_256M, 0x00000000, 0, AC_R|AC_W|AC_X|SA_G|SA_I )
     tlbentry( CFG_PCI_BASE, SZ_256M, 0x00000000, 2, AC_R|AC_W|SA_G|SA_I )
     tlbentry( CFG_PCI_MEMBASE, SZ_256M, 0x00000000, 3, AC_R|AC_W|SA_G|SA_I )
     tlbtab_end

board/stxgp3/Makefile

@@ -0,0 +1,48 @@
+#
+# (C) Copyright 2001
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	:= $(BOARD).o flash.o
+SOBJS	:= init.o
+#SOBJS	:=
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) crv $@ $(OBJS)
+
+clean:
+	rm -f $(OBJS) $(SOBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+-include .depend
+
+#########################################################################

board/stxgp3/config.mk

@@ -0,0 +1,33 @@
+# Modified by Xianghua Xiao, X.Xiao@motorola.com
+# (C) Copyright 2002,2003 Motorola Inc.
+#
+# Copied from ADS85xx for STx GP3 - Dan Malek
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# default CCARBAR is at 0xff700000
+# assume U-Boot is less than 0.5MB
+#
+TEXT_BASE = 0xfff80000
+
+PLATFORM_CPPFLAGS += -DCONFIG_MPC85xx=1
+PLATFORM_CPPFLAGS += -DCONFIG_MPC8560=1
+PLATFORM_CPPFLAGS += -DCONFIG_E500=1

board/stxgp3/flash.c

@@ -0,0 +1,517 @@
+/*
+ * (C) Copyright 2003, Dan Malek, Embedded Edge, LLC.  <dan@embeddededge.com>
+ * Copied from ADS85xx.
+ * Updated to support the Silicon Tx GP3 8560.  We should only find
+ * two Intel 28F640 parts in 16-bit mode (i.e. 32-bit wide flash),
+ * but I left other code here in case people order custom boards.
+ *
+ * (C) Copyright 2003 Motorola Inc.
+ *  Xianghua Xiao,(X.Xiao@motorola.com)
+ *
+ * (C) Copyright 2000, 2001
+ *  Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * (C) Copyright 2001, Stuart Hughes, Lineo Inc, stuarth@lineo.com
+ * Add support the Sharp chips on the mpc8260ads.
+ * I started with board/ip860/flash.c and made changes I found in
+ * the MTD project by David Schleef.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+
+#if !defined(CFG_NO_FLASH)
+
+flash_info_t	flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips	*/
+
+#if defined(CFG_ENV_IS_IN_FLASH)
+# ifndef  CFG_ENV_ADDR
+#  define CFG_ENV_ADDR	(CFG_FLASH_BASE + CFG_ENV_OFFSET)
+# endif
+# ifndef  CFG_ENV_SIZE
+#  define CFG_ENV_SIZE	CFG_ENV_SECT_SIZE
+# endif
+# ifndef  CFG_ENV_SECT_SIZE
+#  define CFG_ENV_SECT_SIZE  CFG_ENV_SIZE
+# endif
+#endif
+
+#undef DEBUG
+
+/*-----------------------------------------------------------------------
+ * Functions
+ */
+static ulong flash_get_size (vu_long *addr, flash_info_t *info);
+static int write_word (flash_info_t *info, ulong dest, ulong data);
+static int clear_block_lock_bit(vu_long * addr);
+/*-----------------------------------------------------------------------
+ */
+
+unsigned long flash_init (void)
+{
+	unsigned long size;
+	int i;
+
+	/* Init: enable write,
+	 * or we cannot even write flash commands
+	 */
+	for (i=0; i<CFG_MAX_FLASH_BANKS; ++i) {
+		flash_info[i].flash_id = FLASH_UNKNOWN;
+
+		/* set the default sector offset */
+	}
+
+	/* Static FLASH Bank configuration here - FIXME XXX */
+
+	size = flash_get_size((vu_long *)CFG_FLASH_BASE, &flash_info[0]);
+
+	if (flash_info[0].flash_id == FLASH_UNKNOWN) {
+		printf ("## Unknown FLASH on Bank 0 - Size = 0x%08lx = %ld MB\n",
+			size, size<<20);
+	}
+
+	/* Re-do sizing to get full correct info */
+	size = flash_get_size((vu_long *)CFG_FLASH_BASE, &flash_info[0]);
+
+	flash_info[0].size = size;
+
+#if !defined(CONFIG_RAM_AS_FLASH)
+#if CFG_MONITOR_BASE >= CFG_FLASH_BASE
+	/* monitor protection ON by default */
+	flash_protect(FLAG_PROTECT_SET,
+		      CFG_MONITOR_BASE,
+		      CFG_MONITOR_BASE+monitor_flash_len-1,
+		      &flash_info[0]);
+#endif
+
+#ifdef	CFG_ENV_IS_IN_FLASH
+	/* ENV protection ON by default */
+	flash_protect(FLAG_PROTECT_SET,
+		      CFG_ENV_ADDR,
+		      CFG_ENV_ADDR+CFG_ENV_SECT_SIZE-1,
+		      &flash_info[0]);
+#endif
+#endif
+	return (size);
+}
+
+/*-----------------------------------------------------------------------
+ */
+void flash_print_info  (flash_info_t *info)
+{
+	int i;
+
+	if (info->flash_id == FLASH_UNKNOWN) {
+		printf ("missing or unknown FLASH type\n");
+		return;
+	}
+
+	switch (info->flash_id & FLASH_VENDMASK) {
+	case FLASH_MAN_INTEL:	printf ("Intel ");		break;
+	case FLASH_MAN_SHARP:   printf ("Sharp ");		break;
+	default:		printf ("Unknown Vendor ");	break;
+	}
+
+	switch (info->flash_id & FLASH_TYPEMASK) {
+	case FLASH_28F640C3T:	printf ("28F640C3T (64 Mbit x 2, 128 x 128k)\n");
+				break;
+	default:		printf ("Unknown Chip Type\n");
+				break;
+	}
+
+	printf ("  Size: %ld MB in %d Sectors\n",
+		info->size >> 20, info->sector_count);
+
+	printf ("  Sector Start Addresses:");
+	for (i=0; i<info->sector_count; ++i) {
+		if ((i % 5) == 0)
+			printf ("\n   ");
+		printf (" %08lX%s",
+			info->start[i],
+			info->protect[i] ? " (RO)" : "     "
+		);
+	}
+	printf ("\n");
+}
+
+/*
+ * The following code cannot be run from FLASH!
+ */
+
+static ulong flash_get_size (vu_long *addr, flash_info_t *info)
+{
+	short i;
+	ulong value;
+	ulong base = (ulong)addr;
+	ulong sector_offset;
+
+#ifdef DEBUG
+	printf("Check flash at 0x%08x\n",(uint)addr);
+#endif
+	/* Write "Intelligent Identifier" command: read Manufacturer ID */
+	*addr = 0x90909090;
+	udelay(20);
+	asm("sync");
+
+	value = addr[0] & 0x00FF00FF;
+
+#ifdef DEBUG
+	printf("manufacturer=0x%x\n",(uint)value);
+#endif
+	switch (value) {
+	case MT_MANUFACT:	/* SHARP, MT or => Intel */
+	case INTEL_ALT_MANU:
+		info->flash_id = FLASH_MAN_INTEL;
+		break;
+	default:
+		printf("unknown manufacturer: %x\n", (unsigned int)value);
+		info->flash_id = FLASH_UNKNOWN;
+		info->sector_count = 0;
+		info->size = 0;
+		return (0);			/* no or unknown flash	*/
+	}
+
+	value = addr[1];             /* device ID            */
+
+#ifdef DEBUG
+	printf("deviceID=0x%x\n",(uint)value);
+#endif
+	switch (value) {
+
+	case (INTEL_ID_28F640C3T):
+		info->flash_id += FLASH_28F640C3T;
+		info->sector_count = 135;
+		info->size = 0x01000000;
+		sector_offset = 0x20000;
+		break;				/* => 2x8 MB		*/
+
+	default:
+		info->flash_id = FLASH_UNKNOWN;
+		return (0);			/* => no or unknown flash */
+
+	}
+
+	/* set up sector start address table
+	 * The first 127 blocks are large, the last 8 are small.
+	 */
+	for (i = 0; i < 127; i++) {
+		info->start[i] = base;
+		base += sector_offset;
+		/* Sectors are locked upon reset */
+		info->protect[i] = 0;
+	}
+	for (i = 127; i < 135; i++) {
+		info->start[i] = base;
+		base += 0x4000;
+		/* Sectors are locked upon reset */
+		info->protect[i] = 0;
+	}
+
+
+	/*
+	 * Prevent writes to uninitialized FLASH.
+	 */
+	if (info->flash_id != FLASH_UNKNOWN) {
+		addr = (vu_long *)info->start[0];
+		*addr = 0xFFFFFF;	/* reset bank to read array mode */
+		asm("sync");
+	}
+
+	return (info->size);
+}
+
+
+/*-----------------------------------------------------------------------
+ */
+
+int	flash_erase (flash_info_t *info, int s_first, int s_last)
+{
+	int flag, prot, sect;
+	ulong start, now, last;
+
+	if ((s_first < 0) || (s_first > s_last)) {
+		if (info->flash_id == FLASH_UNKNOWN) {
+			printf ("- missing\n");
+		} else {
+			printf ("- no sectors to erase\n");
+		}
+		return 1;
+	}
+
+	if (    ((info->flash_id & FLASH_VENDMASK) != FLASH_MAN_INTEL)
+	     && ((info->flash_id & FLASH_VENDMASK) != FLASH_MAN_SHARP) ) {
+		printf ("Can't erase unknown flash type %08lx - aborted\n",
+			info->flash_id);
+		return 1;
+	}
+
+	prot = 0;
+	for (sect=s_first; sect<=s_last; ++sect) {
+		if (info->protect[sect]) {
+			prot++;
+		}
+	}
+
+	if (prot) {
+		printf ("- Warning: %d protected sectors will not be erased!\n",
+			prot);
+	} else {
+		printf ("\n");
+	}
+
+#ifdef DEBUG
+	printf("\nFlash Erase:\n");
+#endif
+	/* Make Sure Block Lock Bit is not set. */
+	if(clear_block_lock_bit((vu_long *)(info->start[s_first]))){
+		return 1;
+	}
+
+	/* Start erase on unprotected sectors */
+#if defined(DEBUG)
+	printf("Begin to erase now,s_first=0x%x s_last=0x%x...\n",s_first,s_last);
+#endif
+	for (sect = s_first; sect<=s_last; sect++) {
+		if (info->protect[sect] == 0) {	/* not protected */
+			vu_long *addr = (vu_long *)(info->start[sect]);
+			asm("sync");
+
+			last = start = get_timer (0);
+
+			/* Disable interrupts which might cause a timeout here */
+			flag = disable_interrupts();
+
+			/* Reset Array */
+			*addr = 0xffffffff;
+			asm("sync");
+			/* Clear Status Register */
+			*addr = 0x50505050;
+			asm("sync");
+			/* Single Block Erase Command */
+			*addr = 0x20202020;
+			asm("sync");
+			/* Confirm */
+			*addr = 0xD0D0D0D0;
+			asm("sync");
+
+			if((info->flash_id & FLASH_TYPEMASK) != FLASH_LH28F016SCT) {
+			    /* Resume Command, as per errata update */
+			    *addr = 0xD0D0D0D0;
+			    asm("sync");
+			}
+
+			/* re-enable interrupts if necessary */
+			if (flag)
+				enable_interrupts();
+
+			/* wait at least 80us - let's wait 1 ms */
+			udelay (1000);
+			while ((*addr & 0x00800080) != 0x00800080) {
+				if(*addr & 0x00200020){
+					printf("Error in Block Erase - Lock Bit may be set!\n");
+					printf("Status Register = 0x%X\n", (uint)*addr);
+					*addr = 0xFFFFFFFF;	/* reset bank */
+					asm("sync");
+					return 1;
+				}
+				if ((now=get_timer(start)) > CFG_FLASH_ERASE_TOUT) {
+					printf ("Timeout\n");
+					*addr = 0xFFFFFFFF;	/* reset bank */
+					asm("sync");
+					return 1;
+				}
+				/* show that we're waiting */
+				if ((now - last) > 1000) {	/* every second */
+					putc ('.');
+					last = now;
+				}
+			}
+
+			/* reset to read mode */
+			*addr = 0xFFFFFFFF;
+			asm("sync");
+		}
+	}
+
+	printf ("flash erase done\n");
+	return 0;
+}
+
+/*-----------------------------------------------------------------------
+ * Copy memory to flash, returns:
+ * 0 - OK
+ * 1 - write timeout
+ * 2 - Flash not erased
+ */
+
+int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
+{
+	ulong cp, wp, data;
+	int i, l, rc;
+
+	wp = (addr & ~3);	/* get lower word aligned address */
+
+	/*
+	 * handle unaligned start bytes
+	 */
+	if ((l = addr - wp) != 0) {
+		data = 0;
+		for (i=0, cp=wp; i<l; ++i, ++cp) {
+			data = (data << 8) | (*(uchar *)cp);
+		}
+		for (; i<4 && cnt>0; ++i) {
+			data = (data << 8) | *src++;
+			--cnt;
+			++cp;
+		}
+		for (; cnt==0 && i<4; ++i, ++cp) {
+			data = (data << 8) | (*(uchar *)cp);
+		}
+
+		if ((rc = write_word(info, wp, data)) != 0) {
+			return (rc);
+		}
+		wp += 4;
+	}
+
+	/*
+	 * handle word aligned part
+	 */
+	while (cnt >= 4) {
+		data = 0;
+		for (i=0; i<4; ++i) {
+			data = (data << 8) | *src++;
+		}
+		if ((rc = write_word(info, wp, data)) != 0) {
+			return (rc);
+		}
+		wp  += 4;
+		cnt -= 4;
+	}
+
+	if (cnt == 0) {
+		return (0);
+	}
+
+	/*
+	 * handle unaligned tail bytes
+	 */
+	data = 0;
+	for (i=0, cp=wp; i<4 && cnt>0; ++i, ++cp) {
+		data = (data << 8) | *src++;
+		--cnt;
+	}
+	for (; i<4; ++i, ++cp) {
+		data = (data << 8) | (*(uchar *)cp);
+	}
+
+	return (write_word(info, wp, data));
+}
+
+/*-----------------------------------------------------------------------
+ * Write a word to Flash, returns:
+ * 0 - OK
+ * 1 - write timeout
+ * 2 - Flash not erased
+ */
+static int write_word (flash_info_t *info, ulong dest, ulong data)
+{
+	vu_long *addr = (vu_long *)dest;
+	ulong start, csr;
+	int flag;
+
+	/* Check if Flash is (sufficiently) erased */
+	if ((*addr & data) != data) {
+		return (2);
+	}
+	/* Disable interrupts which might cause a timeout here */
+	flag = disable_interrupts();
+
+	/* Write Command */
+	*addr = 0x10101010;
+	asm("sync");
+
+	/* Write Data */
+	*addr = data;
+
+	/* re-enable interrupts if necessary */
+	if (flag)
+		enable_interrupts();
+
+	/* data polling for D7 */
+	start = get_timer (0);
+	flag  = 0;
+
+	while (((csr = *addr) & 0x00800080) != 0x00800080) {
+		if (get_timer(start) > CFG_FLASH_WRITE_TOUT) {
+			flag = 1;
+			break;
+		}
+	}
+	if (csr & 0x40404040) {
+		printf ("CSR indicates write error (%08lx) at %08lx\n", csr, (ulong)addr);
+		flag = 1;
+	}
+
+	/* Clear Status Registers Command */
+	*addr = 0x50505050;
+	asm("sync");
+	/* Reset to read array mode */
+	*addr = 0xFFFFFFFF;
+	asm("sync");
+
+	return (flag);
+}
+
+/*-----------------------------------------------------------------------
+ * Clear Block Lock Bit, returns:
+ * 0 - OK
+ * 1 - Timeout
+ */
+
+static int clear_block_lock_bit(vu_long  * addr)
+{
+	ulong start, now;
+
+	/* Reset Array */
+	*addr = 0xffffffff;
+	asm("sync");
+	/* Clear Status Register */
+	*addr = 0x50505050;
+	asm("sync");
+
+	*addr = 0x60606060;
+	asm("sync");
+	*addr = 0xd0d0d0d0;
+	asm("sync");
+
+	start = get_timer (0);
+	while((*addr & 0x00800080) != 0x00800080){
+		if ((now=get_timer(start)) > CFG_FLASH_ERASE_TOUT) {
+			printf ("Timeout on clearing Block Lock Bit\n");
+			*addr = 0xFFFFFFFF;	/* reset bank */
+			asm("sync");
+			return 1;
+		}
+	}
+	return 0;
+}
+
+#endif /* !CFG_NO_FLASH */

board/stxgp3/init.S

@@ -0,0 +1,153 @@
+/*
+ * Copyright (C) 2003 Embedded Edge, LLC
+ * Dan Malek <dan@embeddededge.com>
+ * Copied from ADS85xx.
+ * Updates for Silicon Tx GP3 8560.  We only support 32-bit flash
+ * and DDR with SPD EEPROM configuration.
+ *
+ * Copyright (C) 2002,2003, Motorola Inc.
+ * Xianghua Xiao <X.Xiao@motorola.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <ppc_asm.tmpl>
+#include <ppc_defs.h>
+#include <asm/cache.h>
+#include <asm/mmu.h>
+#include <config.h>
+#include <mpc85xx.h>
+
+#define	entry_start \
+	mflr	r1 	;	\
+	bl	0f 	;
+
+#define	entry_end \
+0:	mflr	r0	;	\
+	mtlr	r1	;	\
+	blr		;
+
+/* TLB1 entries configuration: */
+
+	.section	.bootpg, "ax"
+	.globl	tlb1_entry
+tlb1_entry:
+	entry_start
+
+		/* If RAMBOOT, we are testing and the BDI has set up
+		 * much of the MMU already.
+		 * TLB 4,5 SDRAM
+		 * TLB 15 is default CCSRBAR.
+		 */
+	.long 0x09	/* the following data table uses a few of 16 TLB entries */
+
+	.long TLB1_MAS0(1,1,0)
+	.long TLB1_MAS1(1,1,0,0,BOOKE_PAGESZ_1M)
+	.long TLB1_MAS2(((CFG_CCSRBAR>>12) & 0xfffff),0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(((CFG_CCSRBAR>>12) & 0xfffff),0,0,0,0,0,1,0,1,0,1)
+
+	.long TLB1_MAS0(1,2,0)
+	.long TLB1_MAS1(1,1,0,0,BOOKE_PAGESZ_16M)
+	.long TLB1_MAS2(((CFG_FLASH_BASE>>12) & 0xfffff),0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(((CFG_FLASH_BASE>>12) & 0xfffff),0,0,0,0,0,1,0,1,0,1)
+
+	.long TLB1_MAS0(1,3,0)
+	.long TLB1_MAS1(1,1,0,0,BOOKE_PAGESZ_1M)
+	.long TLB1_MAS2(((CFG_LBC_LCLDEVS_BASE>>12) & 0xfffff),0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(((CFG_LBC_LCLDEVS_BASE>>12) & 0xfffff),0,0,0,0,0,1,0,1,0,1)
+	.long TLB1_MAS0(1,4,0)
+	.long TLB1_MAS1(0,0,0,0,BOOKE_PAGESZ_1M)
+	.long TLB1_MAS2(0,0,0,0,0,0,0,0,0)
+	.long TLB1_MAS3(0,0,0,0,0,0,1,0,1,0,1)
+
+	.long TLB1_MAS0(1,5,0)
+	.long TLB1_MAS1(0,0,0,0,BOOKE_PAGESZ_1M)
+	.long TLB1_MAS2(0,0,0,0,0,0,0,0,0)
+	.long TLB1_MAS3(0,0,0,0,0,0,1,0,1,0,1)
+
+	.long TLB1_MAS0(1,6,0)
+	.long TLB1_MAS1(1,1,0,0,BOOKE_PAGESZ_64M)
+#if defined(CONFIG_RAM_AS_FLASH)
+	.long TLB1_MAS2(((CFG_LBC_SDRAM_BASE>>12) & 0xfffff),0,0,0,0,1,0,1,0)
+#else
+	.long TLB1_MAS2(((CFG_LBC_SDRAM_BASE>>12) & 0xfffff),0,0,0,0,0,0,0,0)
+#endif
+	.long TLB1_MAS3(((CFG_LBC_SDRAM_BASE>>12) & 0xfffff),0,0,0,0,0,1,0,1,0,1)
+
+	.long TLB1_MAS0(1,7,0)
+	.long TLB1_MAS1(1,1,0,0,BOOKE_PAGESZ_16K)
+#ifdef CONFIG_L2_INIT_RAM
+	.long TLB1_MAS2(((CFG_INIT_RAM_ADDR>>12) & 0xfffff),0,0,0,1,0,0,0,0)
+#else
+	.long TLB1_MAS2(((CFG_INIT_RAM_ADDR>>12) & 0xfffff),0,0,0,0,0,0,0,0)
+#endif
+	.long TLB1_MAS3(((CFG_INIT_RAM_ADDR>>12) & 0xfffff),0,0,0,0,0,1,0,1,0,1)
+
+	.long TLB1_MAS0(1,8,0)
+	.long TLB1_MAS1(1,1,0,0,BOOKE_PAGESZ_256M)
+	.long TLB1_MAS2(((CFG_PCI_MEM_BASE>>12) & 0xfffff),0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(((CFG_PCI_MEM_BASE>>12) & 0xfffff),0,0,0,0,0,1,0,1,0,1)
+
+#if (CFG_CCSRBAR_DEFAULT != CFG_CCSRBAR)
+	.long TLB1_MAS0(1,15,0)
+	.long TLB1_MAS1(1,1,0,0,BOOKE_PAGESZ_1M)
+	.long TLB1_MAS2(((CFG_CCSRBAR_DEFAULT>>12) & 0xfffff),0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(((CFG_CCSRBAR_DEFAULT>>12) & 0xfffff),0,0,0,0,0,1,0,1,0,1)
+#else
+	.long TLB1_MAS0(1,15,0)
+	.long TLB1_MAS1(0,0,0,0,BOOKE_PAGESZ_1M)
+	.long TLB1_MAS2(0,0,0,0,0,0,0,0,0)
+	.long TLB1_MAS3(0,0,0,0,0,0,1,0,1,0,1)
+#endif
+	entry_end
+
+/* LAW(Local Access Window) configuration:
+ * 0000_0000-8000_0000: Up to 2G DDR
+ * f000_0000-f3ff_ffff: PCI(256M)
+ * f400_0000-f7ff_ffff: RapidIO(128M)
+ * f800_0000-ffff_ffff: localbus(128M)
+ *   f800_0000-fbff_ffff: LBC SDRAM(64M)
+ *   fc00_0000-fcff_ffff: LBC BCSR (1M, Chip select 1)
+ *   fdf0_0000-fdff_ffff: CCSRBAR(1M)
+ *   ff00_0000-ffff_ffff: Flash(16M)
+ * We don't need a local window for CCSRBAR and flash because they
+ * reside in their default mapped spaces.
+ */
+
+#define LAWBAR0 0
+#define LAWAR0  ((LAWAR_TRGT_IF_DDR | (LAWAR_SIZE & LAWAR_SIZE_2G)) & ~LAWAR_EN)
+
+#define LAWBAR1 ((CFG_PCI_MEM_BASE>>12) & 0xfffff)
+#define LAWAR1  (LAWAR_EN | LAWAR_TRGT_IF_PCIX | (LAWAR_SIZE & LAWAR_SIZE_256M))
+
+#if !defined(CONFIG_RAM_AS_FLASH)
+#define LAWBAR2 ((CFG_LBC_SDRAM_BASE>>12) & 0xfffff)
+#define LAWAR2  (LAWAR_EN | LAWAR_TRGT_IF_LBC | (LAWAR_SIZE & LAWAR_SIZE_128M))
+#else
+#define LAWBAR2 0
+#define LAWAR2 ((LAWAR_TRGT_IF_LBC | (LAWAR_SIZE & LAWAR_SIZE_128M)) & ~LAWAR_EN)
+#endif
+
+	.section .bootpg, "ax"
+	.globl  law_entry
+law_entry:
+	entry_start
+	.long 0x03
+	.long LAWBAR0,LAWAR0,LAWBAR1,LAWAR1,LAWBAR2,LAWAR2
+	entry_end

board/stxgp3/stxgp3.c

@@ -0,0 +1,424 @@
+/*
+ * (C) Copyright 2003, Embedded Edge, LLC
+ * Dan Malek, <dan@embeddededge.com>
+ * Copied from ADS85xx.
+ * Updates for Silicon Tx GP3 8560
+ *
+ * (C) Copyright 2003,Motorola Inc.
+ * Xianghua Xiao, (X.Xiao@motorola.com)
+ *
+ * (C) Copyright 2002 Scott McNutt <smcnutt@artesyncp.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+
+extern long int spd_sdram (void);
+
+#include <common.h>
+#include <asm/processor.h>
+#include <asm/immap_85xx.h>
+#include <ioports.h>
+#include <asm/io.h>
+#include <spd.h>
+#include <miiphy.h>
+
+long int fixed_sdram (void);
+
+/*
+ * I/O Port configuration table
+ *
+ * if conf is 1, then that port pin will be configured at boot time
+ * according to the five values podr/pdir/ppar/psor/pdat for that entry
+ */
+
+const iop_conf_t iop_conf_tab[4][32] = {
+
+    /* Port A configuration */
+    {   /*            conf ppar psor pdir podr pdat */
+	/* PA31 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 TxENB */
+	/* PA30 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 TxClav   */
+	/* PA29 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 TxSOC  */
+	/* PA28 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 RxENB */
+	/* PA27 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 RxSOC */
+	/* PA26 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 RxClav */
+	/* PA25 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXD[0] */
+	/* PA24 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXD[1] */
+	/* PA23 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXD[2] */
+	/* PA22 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXD[3] */
+	/* PA21 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXD[4] */
+	/* PA20 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXD[5] */
+	/* PA19 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXD[6] */
+	/* PA18 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXD[7] */
+	/* PA17 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXD[7] */
+	/* PA16 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXD[6] */
+	/* PA15 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXD[5] */
+	/* PA14 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXD[4] */
+	/* PA13 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXD[3] */
+	/* PA12 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXD[2] */
+	/* PA11 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXD[1] */
+	/* PA10 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXD[0] */
+	/* PA9  */ {   0,   1,   1,   1,   0,   0   }, /* FCC1 L1TXD */
+	/* PA8  */ {   0,   1,   1,   0,   0,   0   }, /* FCC1 L1RXD */
+	/* PA7  */ {   0,   0,   0,   1,   0,   0   }, /* PA7 */
+	/* PA6  */ {   0,   1,   1,   1,   0,   0   }, /* TDM A1 L1RSYNC */
+	/* PA5  */ {   0,   0,   0,   1,   0,   0   }, /* PA5 */
+	/* PA4  */ {   0,   0,   0,   1,   0,   0   }, /* PA4 */
+	/* PA3  */ {   0,   0,   0,   1,   0,   0   }, /* PA3 */
+	/* PA2  */ {   0,   0,   0,   1,   0,   0   }, /* PA2 */
+	/* PA1  */ {   1,   0,   0,   0,   0,   0   }, /* FREERUN */
+	/* PA0  */ {   0,   0,   0,   1,   0,   0   }  /* PA0 */
+    },
+
+    /* Port B configuration */
+    {   /*            conf ppar psor pdir podr pdat */
+	/* PB31 */ {   1,   1,   0,   1,   0,   0   }, /* FCC2 MII TX_ER */
+	/* PB30 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RX_DV */
+	/* PB29 */ {   1,   1,   1,   1,   0,   0   }, /* FCC2 MII TX_EN */
+	/* PB28 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RX_ER */
+	/* PB27 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII COL */
+	/* PB26 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII CRS */
+	/* PB25 */ {   1,   1,   0,   1,   0,   0   }, /* FCC2 MII TxD[3] */
+	/* PB24 */ {   1,   1,   0,   1,   0,   0   }, /* FCC2 MII TxD[2] */
+	/* PB23 */ {   1,   1,   0,   1,   0,   0   }, /* FCC2 MII TxD[1] */
+	/* PB22 */ {   1,   1,   0,   1,   0,   0   }, /* FCC2 MII TxD[0] */
+	/* PB21 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RxD[0] */
+	/* PB20 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RxD[1] */
+	/* PB19 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RxD[2] */
+	/* PB18 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RxD[3] */
+	/* PB17 */ {   0,   1,   0,   0,   0,   0   }, /* FCC3:RX_DIV */
+	/* PB16 */ {   0,   1,   0,   0,   0,   0   }, /* FCC3:RX_ERR */
+	/* PB15 */ {   0,   1,   0,   1,   0,   0   }, /* FCC3:TX_ERR */
+	/* PB14 */ {   0,   1,   0,   1,   0,   0   }, /* FCC3:TX_EN */
+	/* PB13 */ {   0,   1,   0,   0,   0,   0   }, /* FCC3:COL */
+	/* PB12 */ {   0,   1,   0,   0,   0,   0   }, /* FCC3:CRS */
+	/* PB11 */ {   0,   1,   0,   0,   0,   0   }, /* FCC3:RXD */
+	/* PB10 */ {   0,   1,   0,   0,   0,   0   }, /* FCC3:RXD */
+	/* PB9  */ {   0,   1,   0,   0,   0,   0   }, /* FCC3:RXD */
+	/* PB8  */ {   0,   1,   0,   0,   0,   0   }, /* FCC3:RXD */
+	/* PB7  */ {   0,   1,   0,   1,   0,   0   }, /* FCC3:TXD */
+	/* PB6  */ {   0,   1,   0,   1,   0,   0   }, /* FCC3:TXD */
+	/* PB5  */ {   0,   1,   0,   1,   0,   0   }, /* FCC3:TXD */
+	/* PB4  */ {   0,   1,   0,   1,   0,   0   }, /* FCC3:TXD */
+	/* PB3  */ {   0,   0,   0,   0,   0,   0   }, /* pin doesn't exist */
+	/* PB2  */ {   0,   0,   0,   0,   0,   0   }, /* pin doesn't exist */
+	/* PB1  */ {   0,   0,   0,   0,   0,   0   }, /* pin doesn't exist */
+	/* PB0  */ {   0,   0,   0,   0,   0,   0   }  /* pin doesn't exist */
+    },
+
+    /* Port C */
+    {   /*            conf ppar psor pdir podr pdat */
+	/* PC31 */ {   0,   0,   0,   1,   0,   0   }, /* PC31 */
+	/* PC30 */ {   0,   0,   0,   1,   0,   0   }, /* PC30 */
+	/* PC29 */ {   0,   1,   1,   0,   0,   0   }, /* SCC1 EN *CLSN */
+	/* PC28 */ {   0,   0,   0,   1,   0,   0   }, /* PC28 */
+	/* PC27 */ {   0,   0,   0,   1,   0,   0   }, /* UART Clock in */
+	/* PC26 */ {   0,   0,   0,   1,   0,   0   }, /* PC26 */
+	/* PC25 */ {   0,   0,   0,   1,   0,   0   }, /* PC25 */
+	/* PC24 */ {   0,   0,   0,   1,   0,   0   }, /* PC24 */
+	/* PC23 */ {   0,   1,   0,   1,   0,   0   }, /* ATMTFCLK */
+	/* PC22 */ {   0,   1,   0,   0,   0,   0   }, /* ATMRFCLK */
+	/* PC21 */ {   0,   1,   0,   0,   0,   0   }, /* SCC1 EN RXCLK */
+	/* PC20 */ {   0,   1,   0,   0,   0,   0   }, /* SCC1 EN TXCLK */
+	/* PC19 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RX_CLK CLK13 */
+	/* PC18 */ {   1,   1,   0,   0,   0,   0   }, /* FCC Tx Clock (CLK14) */
+	/* PC17 */ {   0,   0,   0,   1,   0,   0   }, /* PC17 */
+	/* PC16 */ {   0,   1,   0,   0,   0,   0   }, /* FCC Tx Clock (CLK16) */
+	/* PC15 */ {   0,   1,   0,   0,   0,   0   }, /* PC15 */
+	/* PC14 */ {   0,   1,   0,   0,   0,   0   }, /* SCC1 EN *CD */
+	/* PC13 */ {   0,   0,   0,   1,   0,   0   }, /* PC13 */
+	/* PC12 */ {   0,   1,   0,   1,   0,   0   }, /* PC12 */
+	/* PC11 */ {   0,   0,   0,   1,   0,   0   }, /* LXT971 transmit control */
+	/* PC10 */ {   0,   0,   0,   1,   0,   0   }, /* FETHMDC */
+	/* PC9  */ {   0,   0,   0,   0,   0,   0   }, /* FETHMDIO */
+	/* PC8  */ {   0,   0,   0,   1,   0,   0   }, /* PC8 */
+	/* PC7  */ {   0,   0,   0,   1,   0,   0   }, /* PC7 */
+	/* PC6  */ {   0,   0,   0,   1,   0,   0   }, /* PC6 */
+	/* PC5  */ {   0,   0,   0,   1,   0,   0   }, /* PC5 */
+	/* PC4  */ {   0,   0,   0,   1,   0,   0   }, /* PC4 */
+	/* PC3  */ {   0,   0,   0,   1,   0,   0   }, /* PC3 */
+	/* PC2  */ {   0,   0,   0,   1,   0,   1   }, /* ENET FDE */
+	/* PC1  */ {   0,   0,   0,   1,   0,   0   }, /* ENET DSQE */
+	/* PC0  */ {   0,   0,   0,   1,   0,   0   }, /* ENET LBK */
+    },
+
+    /* Port D */
+    {   /*            conf ppar psor pdir podr pdat */
+	/* PD31 */ {   0,   1,   0,   0,   0,   0   }, /* SCC1 EN RxD */
+	/* PD30 */ {   0,   1,   1,   1,   0,   0   }, /* SCC1 EN TxD */
+	/* PD29 */ {   0,   1,   0,   1,   0,   0   }, /* SCC1 EN TENA */
+	/* PD28 */ {   1,   1,   0,   0,   0,   0   }, /* SCC2 RxD */
+	/* PD27 */ {   1,   1,   0,   1,   0,   0   }, /* SCC2 TxD */
+	/* PD26 */ {   0,   0,   0,   1,   0,   0   }, /* PD26 */
+	/* PD25 */ {   0,   0,   0,   1,   0,   0   }, /* PD25 */
+	/* PD24 */ {   0,   0,   0,   1,   0,   0   }, /* PD24 */
+	/* PD23 */ {   0,   0,   0,   1,   0,   0   }, /* PD23 */
+	/* PD22 */ {   0,   0,   0,   1,   0,   0   }, /* PD22 */
+	/* PD21 */ {   0,   0,   0,   1,   0,   0   }, /* PD21 */
+	/* PD20 */ {   0,   0,   0,   1,   0,   0   }, /* PD20 */
+	/* PD19 */ {   0,   0,   0,   1,   0,   0   }, /* PD19 */
+	/* PD18 */ {   0,   0,   0,   1,   0,   0   }, /* PD18 */
+	/* PD17 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXPRTY */
+	/* PD16 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXPRTY */
+	/* PD15 */ {   1,   1,   1,   0,   1,   0   }, /* I2C SDA */
+	/* PD14 */ {   1,   1,   1,   0,   0,   0   }, /* I2C CLK */
+	/* PD13 */ {   0,   0,   0,   0,   0,   0   }, /* PD13 */
+	/* PD12 */ {   0,   0,   0,   0,   0,   0   }, /* PD12 */
+	/* PD11 */ {   0,   0,   0,   0,   0,   0   }, /* PD11 */
+	/* PD10 */ {   0,   0,   0,   0,   0,   0   }, /* PD10 */
+	/* PD9  */ {   0,   1,   0,   1,   0,   0   }, /* SMC1 TXD */
+	/* PD8  */ {   0,   1,   0,   0,   0,   0   }, /* SMC1 RXD */
+	/* PD7  */ {   0,   0,   0,   1,   0,   1   }, /* PD7 */
+	/* PD6  */ {   0,   0,   0,   1,   0,   1   }, /* PD6 */
+	/* PD5  */ {   0,   0,   0,   1,   0,   1   }, /* PD5 */
+	/* PD4  */ {   0,   0,   0,   1,   0,   1   }, /* PD4 */
+	/* PD3  */ {   0,   0,   0,   0,   0,   0   }, /* pin doesn't exist */
+	/* PD2  */ {   0,   0,   0,   0,   0,   0   }, /* pin doesn't exist */
+	/* PD1  */ {   0,   0,   0,   0,   0,   0   }, /* pin doesn't exist */
+	/* PD0  */ {   0,   0,   0,   0,   0,   0   }  /* pin doesn't exist */
+    }
+};
+
+static	uint64_t	blinky_increment;
+static	uint64_t	next_led_update;
+static	uint		led_bit;
+
+int board_pre_init (void)
+{
+#if defined(CONFIG_PCI)
+    volatile immap_t *immr = (immap_t *)CFG_IMMR;
+    volatile ccsr_pcix_t *pci = &immr->im_pcix;
+
+    pci->peer &= 0xfffffffdf; /* disable master abort */
+#endif
+	return 0;
+}
+
+void reset_phy (void)
+{
+	volatile uint *blatch;
+
+	blatch = (volatile uint *)CFG_LBC_LCLDEVS_BASE;
+
+	/* reset Giga bit Ethernet port if needed here */
+
+	*blatch &= ~0x000000c0;
+	udelay(100);
+	*blatch = 0x000000c1;	/* Light one led, too */
+	udelay(1000);
+
+#if 0	/* This is the port we really want to use for debugging. */
+	/* reset the CPM FEC port */
+#if (CONFIG_ETHER_INDEX == 2)
+	bcsr->bcsr2 &= ~FETH2_RST;
+	udelay(2);
+	bcsr->bcsr2 |=  FETH2_RST;
+	udelay(1000);
+#elif (CONFIG_ETHER_INDEX == 3)
+	bcsr->bcsr3 &= ~FETH3_RST;
+	udelay(2);
+	bcsr->bcsr3 |=  FETH3_RST;
+	udelay(1000);
+#endif
+#if defined(CONFIG_MII) && defined(CONFIG_ETHER_ON_FCC)
+	miiphy_reset(0x0);	/* reset PHY */
+	miiphy_write(0, PHY_MIPSCR, 0xf028); /* change PHY address to 0x02 */
+	miiphy_write(0x02, PHY_BMCR, PHY_BMCR_AUTON | PHY_BMCR_RST_NEG);
+#endif /* CONFIG_MII */
+#endif
+}
+
+int checkboard (void)
+{
+	sys_info_t sysinfo;
+
+	get_sys_info (&sysinfo);
+
+	printf ("Board: Silicon Tx GPPP 8560 Board\n");
+	printf ("\tCPU: %lu MHz\n", sysinfo.freqProcessor / 1000000);
+	printf ("\tCCB: %lu MHz\n", sysinfo.freqSystemBus / 1000000);
+	printf ("\tDDR: %lu MHz\n", sysinfo.freqSystemBus / 2000000);
+	if((CFG_LBC_LCRR & 0x0f) == 2 || (CFG_LBC_LCRR & 0x0f) == 4 \
+		|| (CFG_LBC_LCRR & 0x0f) == 8) {
+		printf ("\tLBC: %lu MHz\n", sysinfo.freqSystemBus / 1000000 /(CFG_LBC_LCRR & 0x0f));
+	} else {
+		printf("\tLBC: unknown\n");
+	}
+	printf("\tCPM: %lu Mhz\n", sysinfo.freqSystemBus / 1000000);
+	printf("L1 D-cache 32KB, L1 I-cache 32KB enabled.\n");
+
+	return (0);
+}
+
+/* Blinkin' LEDS for Robert.
+*/
+void
+show_activity(int flag)
+{
+	volatile uint *blatch;
+
+	if (next_led_update > get_ticks())
+		return;
+
+	blatch = (volatile uint *)CFG_LBC_LCLDEVS_BASE;
+
+	led_bit >>= 1;
+	if (led_bit == 0)
+		led_bit = 0x08;
+	*blatch = (0xc0 | led_bit);
+	eieio();
+	next_led_update += (get_tbclk() / 4);
+}
+
+long int initdram (int board_type)
+{
+	long dram_size = 0;
+	extern long spd_sdram (void);
+	volatile immap_t *immap = (immap_t *)CFG_IMMR;
+
+#if defined(CONFIG_DDR_DLL)
+	volatile ccsr_gur_t *gur= &immap->im_gur;
+	uint temp_ddrdll = 0;
+
+	/* Work around to stabilize DDR DLL */
+	temp_ddrdll = gur->ddrdllcr;
+	gur->ddrdllcr = ((temp_ddrdll & 0xff) << 16) | 0x80000000;
+	asm("sync;isync;msync");
+#endif
+
+	dram_size = spd_sdram ();
+
+#if defined(CONFIG_DDR_ECC)
+	{
+		/* Initialize all of memory for ECC, then
+		 * enable errors */
+		uint *p = 0;
+		uint i = 0;
+		volatile immap_t *immap = (immap_t *)CFG_IMMR;
+		volatile ccsr_ddr_t *ddr= &immap->im_ddr;
+		dma_init();
+		for (*p = 0; p < (uint *)(8 * 1024); p++) {
+			if (((unsigned int)p & 0x1f) == 0) { dcbz(p); }
+			*p = (unsigned int)0xdeadbeef;
+			if (((unsigned int)p & 0x1c) == 0x1c) { dcbf(p); }
+		}
+
+		/* 8K */
+		dma_xfer((uint *)0x2000,0x2000,(uint *)0);
+		/* 16K */
+		dma_xfer((uint *)0x4000,0x4000,(uint *)0);
+		/* 32K */
+		dma_xfer((uint *)0x8000,0x8000,(uint *)0);
+		/* 64K */
+		dma_xfer((uint *)0x10000,0x10000,(uint *)0);
+		/* 128k */
+		dma_xfer((uint *)0x20000,0x20000,(uint *)0);
+		/* 256k */
+		dma_xfer((uint *)0x40000,0x40000,(uint *)0);
+		/* 512k */
+		dma_xfer((uint *)0x80000,0x80000,(uint *)0);
+		/* 1M */
+		dma_xfer((uint *)0x100000,0x100000,(uint *)0);
+		/* 2M */
+		dma_xfer((uint *)0x200000,0x200000,(uint *)0);
+		/* 4M */
+		dma_xfer((uint *)0x400000,0x400000,(uint *)0);
+
+		for (i = 1; i < dram_size / 0x800000; i++) {
+			dma_xfer((uint *)(0x800000*i),0x800000,(uint *)0);
+		}
+
+		/* Enable errors for ECC */
+		ddr->err_disable = 0x00000000;
+		asm("sync;isync;msync");
+	}
+#endif
+
+	return dram_size;
+}
+
+
+#if defined(CFG_DRAM_TEST)
+int testdram (void)
+{
+	uint *pstart = (uint *) CFG_MEMTEST_START;
+	uint *pend = (uint *) CFG_MEMTEST_END;
+	uint *p;
+
+	printf("SDRAM test phase 1:\n");
+	for (p = pstart; p < pend; p++)
+		*p = 0xaaaaaaaa;
+
+	for (p = pstart; p < pend; p++) {
+		if (*p != 0xaaaaaaaa) {
+			printf ("SDRAM test fails at: %08x\n", (uint) p);
+			return 1;
+		}
+	}
+
+	printf("SDRAM test phase 2:\n");
+	for (p = pstart; p < pend; p++)
+		*p = 0x55555555;
+
+	for (p = pstart; p < pend; p++) {
+		if (*p != 0x55555555) {
+			printf ("SDRAM test fails at: %08x\n", (uint) p);
+			return 1;
+		}
+	}
+
+	printf("SDRAM test passed.\n");
+	return 0;
+}
+#endif
+
+#if !defined(CONFIG_SPD_EEPROM)
+/*************************************************************************
+ *  fixed sdram init -- doesn't use serial presence detect.
+ ************************************************************************/
+long int fixed_sdram (void)
+{
+  #ifndef CFG_RAMBOOT
+	volatile immap_t *immap = (immap_t *)CFG_IMMR;
+	volatile ccsr_ddr_t *ddr= &immap->im_ddr;
+
+	ddr->cs0_bnds = CFG_DDR_CS0_BNDS;
+	ddr->cs0_config = CFG_DDR_CS0_CONFIG;
+	ddr->timing_cfg_1 = CFG_DDR_TIMING_1;
+	ddr->timing_cfg_2 = CFG_DDR_TIMING_2;
+	ddr->sdram_mode = CFG_DDR_MODE;
+	ddr->sdram_interval = CFG_DDR_INTERVAL;
+    #if defined (CONFIG_DDR_ECC)
+	ddr->err_disable = 0x0000000D;
+	ddr->err_sbe = 0x00ff0000;
+    #endif
+	asm("sync;isync;msync");
+	udelay(500);
+    #if defined (CONFIG_DDR_ECC)
+	/* Enable ECC checking */
+	ddr->sdram_cfg = (CFG_DDR_CONTROL | 0x20000000);
+    #else
+	ddr->sdram_cfg = CFG_DDR_CONTROL;
+    #endif
+	asm("sync; isync; msync");
+	udelay(500);
+  #endif
+	return ( CFG_SDRAM_SIZE * 1024 * 1024);
+}
+#endif	/* !defined(CONFIG_SPD_EEPROM) */

board/stxgp3/u-boot.lds

@@ -0,0 +1,157 @@
+/*
+ * (C) Copyright 2003 Embedded Edge, LLC
+ * Dan Malek, <dan@embeddededge.com>
+ * Copied from ADS85xx.
+ * Updates for Silicon Tx GP3 8560.
+ *
+ * (C) Copyright 2002,2003,Motorola,Inc.
+ * Xianghua Xiao, X.Xiao@motorola.com.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+/* Do we need any of these for elf?
+   __DYNAMIC = 0;    */
+SECTIONS
+{
+  .resetvec 0xFFFFFFFC :
+  {
+    *(.resetvec)
+  } = 0xffff
+
+  .bootpg 0xFFFFF000 :
+  {
+    cpu/mpc85xx/start.o	(.bootpg)
+    board/stxgp3/init.o (.bootpg)
+  } = 0xffff
+
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)		}
+  .rela.text     : { *(.rela.text) 	}
+  .rel.data      : { *(.rel.data)		}
+  .rela.data     : { *(.rela.data) 	}
+  .rel.rodata    : { *(.rel.rodata) 	}
+  .rela.rodata   : { *(.rela.rodata) 	}
+  .rel.got       : { *(.rel.got)		}
+  .rela.got      : { *(.rela.got)		}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)		}
+  .rela.bss      : { *(.rela.bss)		}
+  .rel.plt       : { *(.rel.plt)		}
+  .rela.plt      : { *(.rela.plt)		}
+  .init          : { *(.init)	}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    cpu/mpc85xx/start.o	(.text)
+    board/stxgp3/init.o (.text)
+    cpu/mpc85xx/commproc.o (.text)
+    cpu/mpc85xx/traps.o (.text)
+    cpu/mpc85xx/interrupts.o (.text)
+    cpu/mpc85xx/serial_scc.o (.text)
+    cpu/mpc85xx/ether_fcc.o (.text)
+    cpu/mpc85xx/cpu_init.o (.text)
+    cpu/mpc85xx/cpu.o (.text)
+    cpu/mpc85xx/tsec.o (.text)
+    cpu/mpc85xx/speed.o (.text)
+    cpu/mpc85xx/i2c.o (.text)
+    cpu/mpc85xx/spd_sdram.o (.text)
+    common/dlmalloc.o (.text)
+    lib_generic/crc32.o (.text)
+    lib_ppc/extable.o (.text)
+    lib_generic/zlib.o (.text)
+    *(.text)
+    *(.fixup)
+    *(.got1)
+   }
+    _etext = .;
+    PROVIDE (etext = .);
+    .rodata    :
+   {
+    *(.rodata)
+    *(.rodata1)
+    *(.rodata.str1.4)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x00FF) & 0xFFFFFF00;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2;
+  __fixup_entries = (. - _FIXUP_TABLE_) >> 2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  __u_boot_cmd_start = .;
+  .u_boot_cmd : { *(.u_boot_cmd) }
+  __u_boot_cmd_end = .;
+
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(256);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(256);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+  _end = . ;
+  PROVIDE (end = .);
+}

board/utx8245/utx8245.c

@@ -48,35 +48,30 @@ int checkboard(void)
 
 long int initdram(int board_type)
 {
-#if 1
 	long size;
 	long new_bank0_end;
+	long new_bank1_end;
 	long mear1;
 	long emear1;
-/*
-	write_bat(IBAT1, ((CFG_MAX_RAM_SIZE/2) | BATU_BL_256M | BATU_VS | BATU_VP),
-			( (CFG_MAX_RAM_SIZE/2)| BATL_PP_10 | BATL_MEMCOHERENCE));
 
-	write_bat(DBAT1, ((CFG_MAX_RAM_SIZE/2) | BATU_BL_256M | BATU_VS | BATU_VP),
-			( (CFG_MAX_RAM_SIZE/2)| BATL_PP_10 | BATL_MEMCOHERENCE));
-*/
 	size = get_ram_size(CFG_SDRAM_BASE, CFG_MAX_RAM_SIZE);
 
-	new_bank0_end = size - 1;
+	new_bank0_end = size/2 - 1;
+	new_bank1_end = size - 1;
 	mear1 = mpc824x_mpc107_getreg(MEAR1);
 	emear1 = mpc824x_mpc107_getreg(EMEAR1);
-	mear1 = (mear1  & 0xFFFFFF00) |
-		((new_bank0_end & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT);
-	emear1 = (emear1 & 0xFFFFFF00) |
-		((new_bank0_end & MICR_ADDR_MASK) >> MICR_EADDR_SHIFT);
+
+	mear1 = (mear1  & 0xFFFF0000) |
+		((new_bank0_end & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT) |
+		((new_bank1_end & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT << 8);
+	emear1 = (emear1 & 0xFFFF0000) |
+		((new_bank0_end & MICR_EADDR_MASK) >> MICR_EADDR_SHIFT) |
+		((new_bank1_end & MICR_EADDR_MASK) >> MICR_EADDR_SHIFT << 8);
+
 	mpc824x_mpc107_setreg(MEAR1, mear1);
 	mpc824x_mpc107_setreg(EMEAR1, emear1);
 
 	return (size);
-#else
-	return (CFG_MAX_RAM_SIZE);
-#endif
-
 }
 
 

common/cmd_bootm.c

@@ -242,6 +242,8 @@ int do_bootm (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 	if (hdr->ih_arch != IH_CPU_NIOS)
 #elif defined(__M68K__)
 	if (hdr->ih_arch != IH_CPU_M68K)
+#elif defined(__microblaze__)
+	if (hdr->ih_arch != IH_CPU_MICROBLAZE)
 #else
 # error Unknown CPU type
 #endif
@@ -1185,6 +1187,7 @@ print_type (image_header_t *hdr)
 	case IH_CPU_SPARC:	arch = "SPARC";			break;
 	case IH_CPU_SPARC64:	arch = "SPARC 64 Bit";		break;
 	case IH_CPU_M68K:	arch = "M68K"; 			break;
+	case IH_CPU_MICROBLAZE:	arch = "Microblaze"; 		break;
 	default:		arch = "Unknown Architecture";	break;
 	}
 

common/cmd_ide.c

@@ -60,6 +60,11 @@ static unsigned long mips_io_port_base = 0;
 # define SHOW_BOOT_PROGRESS(arg)
 #endif
 
+#ifdef __PPC__
+# define EIEIO		__asm__ volatile ("eieio")
+#else
+# define EIEIO		/* nothing */
+#endif
 
 #undef	IDE_DEBUG
 
@@ -790,9 +795,7 @@ ide_outb(int dev, int port, unsigned char val)
 		dev, port, val, (ATA_CURR_BASE(dev)+port));
 
 	/* Ensure I/O operations complete */
-#ifdef __PPC__
-	__asm__ volatile("eieio");
-#endif
+	EIEIO;
 	*((uchar *)(ATA_CURR_BASE(dev)+port)) = val;
 }
 #else	/* ! __PPC__ */
@@ -810,9 +813,7 @@ ide_inb(int dev, int port)
 {
 	uchar val;
 	/* Ensure I/O operations complete */
-#ifdef __PPC__
-	__asm__ volatile("eieio");
-#endif
+	EIEIO;
 	val = *((uchar *)(ATA_CURR_BASE(dev)+port));
 	PRINTF ("ide_inb (dev= %d, port= 0x%x) : @ 0x%08lx -> 0x%02x\n",
 		dev, port, (ATA_CURR_BASE(dev)+port), val);
@@ -837,9 +838,9 @@ output_data_short(int dev, ulong *sect_buf, int words)
 	pbuf = (ushort *)(ATA_CURR_BASE(dev)+ATA_DATA_REG);
 	dbuf = (ushort *)sect_buf;
 	while (words--) {
-		__asm__ volatile ("eieio");
+		EIEIO;
 		*pbuf = *dbuf++;
-		__asm__ volatile ("eieio");
+		EIEIO;
 	}
 
 	if (words&1)
@@ -895,13 +896,9 @@ output_data(int dev, ulong *sect_buf, int words)
 	pbuf = (ushort *)(ATA_CURR_BASE(dev)+ATA_DATA_REG);
 	dbuf = (ushort *)sect_buf;
 	while (words--) {
-#ifdef __PPC__
-		__asm__ volatile ("eieio");
-#endif
+		EIEIO;
 		*pbuf = *dbuf++;
-#ifdef __PPC__
-		__asm__ volatile ("eieio");
-#endif
+		EIEIO;
 		*pbuf = *dbuf++;
 	}
 #else	/* CONFIG_HMI10 */
@@ -913,13 +910,13 @@ output_data(int dev, ulong *sect_buf, int words)
 	pbuf_odd  = (uchar *)(ATA_CURR_BASE(dev)+ATA_DATA_ODD);
 	dbuf = (uchar *)sect_buf;
 	while (words--) {
-		__asm__ volatile ("eieio");
+		EIEIO;
 		*pbuf_even = *dbuf++;
-		__asm__ volatile ("eieio");
+		EIEIO;
 		*pbuf_odd = *dbuf++;
-		__asm__ volatile ("eieio");
+		EIEIO;
 		*pbuf_even = *dbuf++;
-		__asm__ volatile ("eieio");
+		EIEIO;
 		*pbuf_odd = *dbuf++;
 	}
 #endif	/* CONFIG_HMI10 */
@@ -946,13 +943,9 @@ input_data(int dev, ulong *sect_buf, int words)
 	PRINTF("in input data base for read is %lx\n", (unsigned long) pbuf);
 
 	while (words--) {
-#ifdef __PPC__
-		__asm__ volatile ("eieio");
-#endif
+		EIEIO;
 		*dbuf++ = *pbuf;
-#ifdef __PPC__
-		__asm__ volatile ("eieio");
-#endif
+		EIEIO;
 		*dbuf++ = *pbuf;
 	}
 #else	/* CONFIG_HMI10 */
@@ -964,13 +957,13 @@ input_data(int dev, ulong *sect_buf, int words)
 	pbuf_odd  = (uchar *)(ATA_CURR_BASE(dev)+ATA_DATA_ODD);
 	dbuf = (uchar *)sect_buf;
 	while (words--) {
-		__asm__ volatile ("eieio");
+		EIEIO;
 		*dbuf++ = *pbuf_even;
-		__asm__ volatile ("eieio");
+		EIEIO;
 		*dbuf++ = *pbuf_odd;
-		__asm__ volatile ("eieio");
+		EIEIO;
 		*dbuf++ = *pbuf_even;
-		__asm__ volatile ("eieio");
+		EIEIO;
 		*dbuf++ = *pbuf_odd;
 	}
 #endif	/* CONFIG_HMI10 */
@@ -994,9 +987,9 @@ input_data_short(int dev, ulong *sect_buf, int words)
 	pbuf = (ushort *)(ATA_CURR_BASE(dev)+ATA_DATA_REG);
 	dbuf = (ushort *)sect_buf;
 	while (words--) {
-		__asm__ volatile ("eieio");
+		EIEIO;
 		*dbuf++ = *pbuf;
-		__asm__ volatile ("eieio");
+		EIEIO;
 	}
 
 	if (words&1) {
@@ -1608,9 +1601,7 @@ output_data_shorts(int dev, ushort *sect_buf, int shorts)
 	PRINTF("in output data shorts base for read is %lx\n", (unsigned long) pbuf);
 
 	while (shorts--) {
-#ifdef __PPC__
-		__asm__ volatile ("eieio");
-#endif
+		EIEIO;
 		*pbuf = *dbuf++;
 	}
 #else	/* CONFIG_HMI10 */
@@ -1621,9 +1612,9 @@ output_data_shorts(int dev, ushort *sect_buf, int shorts)
 	pbuf_even = (uchar *)(ATA_CURR_BASE(dev)+ATA_DATA_EVEN);
 	pbuf_odd  = (uchar *)(ATA_CURR_BASE(dev)+ATA_DATA_ODD);
 	while (shorts--) {
-		__asm__ volatile ("eieio");
+		EIEIO;
 		*pbuf_even = *dbuf++;
-		__asm__ volatile ("eieio");
+		EIEIO;
 		*pbuf_odd = *dbuf++;
 	}
 #endif	/* CONFIG_HMI10 */
@@ -1642,9 +1633,7 @@ input_data_shorts(int dev, ushort *sect_buf, int shorts)
 	PRINTF("in input data shorts base for read is %lx\n", (unsigned long) pbuf);
 
 	while (shorts--) {
-#ifdef __PPC__
-		__asm__ volatile ("eieio");
-#endif
+		EIEIO;
 		*dbuf++ = *pbuf;
 	}
 #else	/* CONFIG_HMI10 */
@@ -1655,9 +1644,9 @@ input_data_shorts(int dev, ushort *sect_buf, int shorts)
 	pbuf_even = (uchar *)(ATA_CURR_BASE(dev)+ATA_DATA_EVEN);
 	pbuf_odd  = (uchar *)(ATA_CURR_BASE(dev)+ATA_DATA_ODD);
 	while (shorts--) {
-		__asm__ volatile ("eieio");
+		EIEIO;
 		*dbuf++ = *pbuf_even;
-		__asm__ volatile ("eieio");
+		EIEIO;
 		*dbuf++ = *pbuf_odd;
 	}
 #endif	/* CONFIG_HMI10 */

common/cmd_mii.c

@@ -27,10 +27,13 @@
 
 #include <common.h>
 #include <command.h>
-#include <miiphy.h>
 
 #if (CONFIG_COMMANDS & CFG_CMD_MII)
+#include <miiphy.h>
 
+#define	CONFIG_TERSE_MII	/* XXX necessary here because "miivals.h" is missing */
+
+#ifdef CONFIG_TERSE_MII
 /*
  * Display values from last command.
  */
@@ -144,5 +147,419 @@ U_BOOT_CMD(
 	"mii write <addr> <reg> <data> - write MII PHY <addr> register <reg>\n"
 );
 
+#else /* ! CONFIG_TERSE_MII ================================================= */
+
+#include <miivals.h>
+
+typedef struct _MII_reg_desc_t {
+	ushort regno;
+	char * name;
+} MII_reg_desc_t;
+
+MII_reg_desc_t reg_0_5_desc_tbl[] = {
+	{ 0,   "PHY control register"                },
+	{ 1,   "PHY status register"                 },
+	{ 2,   "PHY ID 1 register"                   },
+	{ 3,   "PHY ID 2 register"                   },
+	{ 4,   "Autonegotiation advertisement register" },
+	{ 5,   "Autonegotiation partner abilities register" },
+};
+
+typedef struct _MII_field_desc_t {
+	ushort hi;
+	ushort lo;
+	ushort mask;
+	char * name;
+} MII_field_desc_t;
+
+MII_field_desc_t reg_0_desc_tbl[] = {
+	{ 15, 15, 0x01, "reset"                        },
+	{ 14, 14, 0x01, "loopback"                     },
+	{ 13,  6, 0x81, "speed selection"              }, /* special */
+	{ 12, 12, 0x01, "A/N enable"                   },
+	{ 11, 11, 0x01, "power-down"                   },
+	{ 10, 10, 0x01, "isolate"                      },
+	{  9,  9, 0x01, "restart A/N"                  },
+	{  8,  8, 0x01, "duplex"                       }, /* special */
+	{  7,  7, 0x01, "collision test enable"        },
+	{  5,  0, 0x3f, "(reserved)"                   }
+};
+
+MII_field_desc_t reg_1_desc_tbl[] = {
+	{ 15, 15, 0x01, "100BASE-T4 able"              },
+	{ 14, 14, 0x01, "100BASE-X  full duplex able"  },
+	{ 13, 13, 0x01, "100BASE-X  half duplex able"  },
+	{ 12, 12, 0x01, "10 Mbps    full duplex able"  },
+	{ 11, 11, 0x01, "10 Mbps    half duplex able"  },
+	{ 10, 10, 0x01, "100BASE-T2 full duplex able"  },
+	{  9,  9, 0x01, "100BASE-T2 half duplex able"  },
+	{  8,  8, 0x01, "extended status"              },
+	{  7,  7, 0x01, "(reserved)"                   },
+	{  6,  6, 0x01, "MF preamble suppression"      },
+	{  5,  5, 0x01, "A/N complete"                 },
+	{  4,  4, 0x01, "remote fault"                 },
+	{  3,  3, 0x01, "A/N able"                     },
+	{  2,  2, 0x01, "link status"                  },
+	{  1,  1, 0x01, "jabber detect"                },
+	{  0,  0, 0x01, "extended capabilities"        },
+};
+
+MII_field_desc_t reg_2_desc_tbl[] = {
+	{ 15,  0, 0xffff, "OUI portion"                },
+};
+
+MII_field_desc_t reg_3_desc_tbl[] = {
+	{ 15, 10, 0x3f, "OUI portion"                },
+	{  9,  4, 0x3f, "manufacturer part number"   },
+	{  3,  0, 0x0f, "manufacturer rev. number"   },
+};
+
+MII_field_desc_t reg_4_desc_tbl[] = {
+	{ 15, 15, 0x01, "next page able"               },
+	{ 14, 14, 0x01, "reserved"                     },
+	{ 13, 13, 0x01, "remote fault"                 },
+	{ 12, 12, 0x01, "reserved"                     },
+	{ 11, 11, 0x01, "asymmetric pause"             },
+	{ 10, 10, 0x01, "pause enable"                 },
+	{  9,  9, 0x01, "100BASE-T4 able"              },
+	{  8,  8, 0x01, "100BASE-TX full duplex able"  },
+	{  7,  7, 0x01, "100BASE-TX able"              },
+	{  6,  6, 0x01, "10BASE-T   full duplex able"  },
+	{  5,  5, 0x01, "10BASE-T   able"              },
+	{  4,  0, 0x1f, "xxx to do"                    },
+};
+
+MII_field_desc_t reg_5_desc_tbl[] = {
+	{ 15, 15, 0x01, "next page able"               },
+	{ 14, 14, 0x01, "acknowledge"                  },
+	{ 13, 13, 0x01, "remote fault"                 },
+	{ 12, 12, 0x01, "(reserved)"                   },
+	{ 11, 11, 0x01, "asymmetric pause able"        },
+	{ 10, 10, 0x01, "pause able"                   },
+	{  9,  9, 0x01, "100BASE-T4 able"              },
+	{  8,  8, 0x01, "100BASE-X full duplex able"   },
+	{  7,  7, 0x01, "100BASE-TX able"              },
+	{  6,  6, 0x01, "10BASE-T full duplex able"    },
+	{  5,  5, 0x01, "10BASE-T able"                },
+	{  4,  0, 0x1f, "xxx to do"                    },
+};
+
+#define DESC0LEN (sizeof(reg_0_desc_tbl)/sizeof(reg_0_desc_tbl[0]))
+#define DESC1LEN (sizeof(reg_1_desc_tbl)/sizeof(reg_1_desc_tbl[0]))
+#define DESC2LEN (sizeof(reg_2_desc_tbl)/sizeof(reg_2_desc_tbl[0]))
+#define DESC3LEN (sizeof(reg_3_desc_tbl)/sizeof(reg_3_desc_tbl[0]))
+#define DESC4LEN (sizeof(reg_4_desc_tbl)/sizeof(reg_4_desc_tbl[0]))
+#define DESC5LEN (sizeof(reg_5_desc_tbl)/sizeof(reg_5_desc_tbl[0]))
+
+typedef struct _MII_field_desc_and_len_t {
+	MII_field_desc_t * pdesc;
+	ushort len;
+} MII_field_desc_and_len_t;
+
+MII_field_desc_and_len_t desc_and_len_tbl[] = {
+	{ reg_0_desc_tbl, DESC0LEN },
+	{ reg_1_desc_tbl, DESC1LEN },
+	{ reg_2_desc_tbl, DESC2LEN },
+	{ reg_3_desc_tbl, DESC3LEN },
+	{ reg_4_desc_tbl, DESC4LEN },
+	{ reg_5_desc_tbl, DESC5LEN },
+};
+
+static void dump_reg(
+	ushort             regval,
+	MII_reg_desc_t   * prd,
+	MII_field_desc_and_len_t * pdl);
+
+static int special_field(
+	ushort regno,
+	MII_field_desc_t * pdesc,
+	ushort regval);
+
+void MII_dump_0_to_5(
+	ushort regvals[6],
+	uchar reglo,
+	uchar reghi)
+{
+	ulong i;
+
+	for (i = 0; i < 6; i++) {
+		if ((reglo <= i) && (i <= reghi))
+			dump_reg(regvals[i], &reg_0_5_desc_tbl[i],
+				&desc_and_len_tbl[i]);
+	}
+}
+
+static void dump_reg(
+	ushort             regval,
+	MII_reg_desc_t   * prd,
+	MII_field_desc_and_len_t * pdl)
+{
+	ulong i;
+	ushort mask_in_place;
+	MII_field_desc_t * pdesc;
+
+	printf("%u.     (%04hx)                 -- %s --\n",
+		prd->regno, regval, prd->name);
+
+	for (i = 0; i < pdl->len; i++) {
+		pdesc = &pdl->pdesc[i];
+
+		mask_in_place = pdesc->mask << pdesc->lo;
+
+		printf("  (%04hx:%04hx) %u.",
+			mask_in_place,
+			regval & mask_in_place,
+			prd->regno);
+
+		if (special_field(prd->regno, pdesc, regval)) {
+		}
+		else {
+			if (pdesc->hi == pdesc->lo)
+				printf("%2u   ", pdesc->lo);
+			else
+				printf("%2u-%2u", pdesc->hi, pdesc->lo);
+			printf(" = %5u    %s",
+				(regval & mask_in_place) >> pdesc->lo,
+				pdesc->name);
+		}
+		printf("\n");
+
+	}
+	printf("\n");
+}
+
+/* Special fields:
+** 0.6,13
+** 0.8
+** 2.15-0
+** 3.15-0
+** 4.4-0
+** 5.4-0
+*/
+
+static int special_field(
+	ushort regno,
+	MII_field_desc_t * pdesc,
+	ushort regval)
+{
+	if ((regno == 0) && (pdesc->lo == 6)) {
+		ushort speed_bits = regval & MII_CTL_SPEED_MASK;
+		printf("%2u,%2u =   b%u%u    speed selection = %s Mbps",
+			6, 13,
+			(regval >>  6) & 1,
+			(regval >> 13) & 1,
+			speed_bits == MII_CTL_SPEED_1000_MBPS ? "1000" :
+			speed_bits == MII_CTL_SPEED_100_MBPS  ? "100" :
+			speed_bits == MII_CTL_SPEED_10_MBPS   ? "10" :
+			"???");
+		return 1;
+	}
+
+	else if ((regno == 0) && (pdesc->lo == 8)) {
+		printf("%2u    = %5u    duplex = %s",
+			pdesc->lo,
+			(regval >>  pdesc->lo) & 1,
+			((regval >> pdesc->lo) & 1) ? "full" : "half");
+		return 1;
+	}
+
+	else if ((regno == 4) && (pdesc->lo == 0)) {
+		ushort sel_bits = (regval >> pdesc->lo) & pdesc->mask;
+		printf("%2u-%2u = %5u    selector = %s",
+			pdesc->hi, pdesc->lo, sel_bits,
+			sel_bits == MII_AN_ADV_IEEE_802_3 ?
+				"IEEE 802.3" :
+			sel_bits == MII_AN_ADV_IEEE_802_9_ISLAN_16T ?
+				"IEEE 802.9 ISLAN-16T" :
+			"???");
+		return 1;
+	}
+
+	else if ((regno == 5) && (pdesc->lo == 0)) {
+		ushort sel_bits = (regval >> pdesc->lo) & pdesc->mask;
+		printf("%2u-%2u =     %u    selector = %s",
+			pdesc->hi, pdesc->lo, sel_bits,
+			sel_bits == MII_AN_PARTNER_IEEE_802_3 ?
+				"IEEE 802.3" :
+			sel_bits == MII_AN_PARTNER_IEEE_802_9_ISLAN_16T ?
+				"IEEE 802.9 ISLAN-16T" :
+			"???");
+		return 1;
+	}
+
+	return 0;
+}
+
+uint last_op;
+uint last_data;
+uint last_addr_lo;
+uint last_addr_hi;
+uint last_reg_lo;
+uint last_reg_hi;
+
+static void extract_range(
+	char * input,
+	unsigned char * plo,
+	unsigned char * phi)
+{
+	char * end;
+	*plo = simple_strtoul(input, &end, 16);
+	if (*end == '-') {
+		end++;
+		*phi = simple_strtoul(end, NULL, 16);
+	}
+	else {
+		*phi = *plo;
+	}
+}
+
+/* ---------------------------------------------------------------- */
+int do_mii (cmd_tbl_t * cmdtp, int flag, int argc, char *argv[])
+{
+	char		op;
+	unsigned char	addrlo, addrhi, reglo, reghi;
+	unsigned char	addr, reg;
+	unsigned short	data;
+	int		rcode = 0;
+
+#ifdef CONFIG_8xx
+	mii_init ();
+#endif
+
+	/*
+	 * We use the last specified parameters, unless new ones are
+	 * entered.
+	 */
+	op     = last_op;
+	addrlo = last_addr_lo;
+	addrhi = last_addr_hi;
+	reglo  = last_reg_lo;
+	reghi  = last_reg_hi;
+	data   = last_data;
+
+	if ((flag & CMD_FLAG_REPEAT) == 0) {
+		op = argv[1][0];
+		if (argc >= 3)
+			extract_range(argv[2], &addrlo, &addrhi);
+		if (argc >= 4)
+			extract_range(argv[3], &reglo, &reghi);
+		if (argc >= 5)
+			data = simple_strtoul (argv[4], NULL, 16);
+	}
+
+	/*
+	 * check info/read/write.
+	 */
+	if (op == 'i') {
+		unsigned char j, start, end;
+		unsigned int oui;
+		unsigned char model;
+		unsigned char rev;
+
+		/*
+		 * Look for any and all PHYs.  Valid addresses are 0..31.
+		 */
+		if (argc >= 3) {
+			start = addr; end = addr + 1;
+		} else {
+			start = 0; end = 32;
+		}
+
+		for (j = start; j < end; j++) {
+			if (miiphy_info (j, &oui, &model, &rev) == 0) {
+				printf("PHY 0x%02X: "
+					"OUI = 0x%04X, "
+					"Model = 0x%02X, "
+					"Rev = 0x%02X, "
+					"%3dbaseT, %s\n",
+					j, oui, model, rev,
+					miiphy_speed (j),
+					miiphy_duplex (j) == FULL ? "FDX" : "HDX");
+			}
+		}
+	} else if (op == 'r') {
+		for (addr = addrlo; addr <= addrhi; addr++) {
+			for (reg = reglo; reg <= reghi; reg++) {
+				data = 0xffff;
+				if (miiphy_read (addr, reg, &data) != 0) {
+					printf(
+					"Error reading from the PHY addr=%02x reg=%02x\n",
+						addr, reg);
+					rcode = 1;
+				}
+				else {
+					if ((addrlo != addrhi) || (reglo != reghi))
+						printf("addr=%02x reg=%02x data=",
+							(uint)addr, (uint)reg);
+					printf("%04X\n", data & 0x0000FFFF);
+				}
+			}
+			if ((addrlo != addrhi) && (reglo != reghi))
+				printf("\n");
+		}
+	} else if (op == 'w') {
+		for (addr = addrlo; addr <= addrhi; addr++) {
+			for (reg = reglo; reg <= reghi; reg++) {
+				if (miiphy_write (addr, reg, data) != 0) {
+					printf("Error writing to the PHY addr=%02x reg=%02x\n",
+						addr, reg);
+					rcode = 1;
+				}
+			}
+		}
+	} else if (op == 'd') {
+		ushort regs[6];
+		int ok = 1;
+		if ((reglo > 5) || (reghi > 5)) {
+			printf(
+				"The MII dump command only formats the "
+				"standard MII registers, 0-5.\n");
+			return 1;
+		}
+		for (addr = addrlo; addr <= addrhi; addr++) {
+			for (reg = 0; reg < 6; reg++) {
+				if (miiphy_read(addr, reg, &regs[reg]) != 0) {
+					ok = 0;
+					printf(
+					"Error reading from the PHY addr=%02x reg=%02x\n",
+						addr, reg);
+					rcode = 1;
+				}
+			}
+			if (ok)
+				MII_dump_0_to_5(regs, reglo, reghi);
+			printf("\n");
+		}
+	} else {
+		printf("Usage:\n%s\n", cmdtp->usage);
+		return 1;
+	}
+
+	/*
+	 * Save the parameters for repeats.
+	 */
+	last_op      = op;
+	last_addr_lo = addrlo;
+	last_addr_hi = addrhi;
+	last_reg_lo  = reglo;
+	last_reg_hi  = reghi;
+	last_data    = data;
+
+	return rcode;
+}
+
+/***************************************************/
+
+U_BOOT_CMD(
+	mii,	5,	1,	do_mii,
+	"mii     - MII utility commands\n",
+	"info  <addr>                  - display MII PHY info\n"
+	"mii read  <addr> <reg>        - read  MII PHY <addr> register <reg>\n"
+	"mii write <addr> <reg> <data> - write MII PHY <addr> register <reg>\n"
+	"mii dump  <addr> <reg>        - pretty-print <addr> <reg> (0-5 only)\n"
+	"Addr and/or reg may be ranges, e.g. 2-7.\n"
+);
+
+#endif /* CONFIG_TERSE_MII */
 
 #endif /* CFG_CMD_MII */

common/cmd_usb.c

@@ -598,14 +598,14 @@ U_BOOT_CMD(
 	usb,	5,	1,	do_usb,
 	"usb     - USB sub-system\n",
 	"reset - reset (rescan) USB controller\n"
-	"usb  stop [f]  - stop USB [f]=force stop\n"
-	"usb  tree  - show USB device tree\n"
-	"usb  info [dev] - show available USB devices\n"
-	"usb  scan  - (re-)scan USB bus for storage devices\n"
-	"usb  device [dev] - show or set current USB storage device\n"
-	"usb  part [dev] - print partition table of one or all USB storage devices\n"
-	"usb  read addr blk# cnt - read `cnt' blocks starting at block `blk#'\n"
-	"     to memory address `addr'\n"
+	"usb stop [f]  - stop USB [f]=force stop\n"
+	"usb tree  - show USB device tree\n"
+	"usb info [dev] - show available USB devices\n"
+	"usb scan  - (re-)scan USB bus for storage devices\n"
+	"usb device [dev] - show or set current USB storage device\n"
+	"usb part [dev] - print partition table of one or all USB storage devices\n"
+	"usb read addr blk# cnt - read `cnt' blocks starting at block `blk#'\n"
+	"    to memory address `addr'\n"
 );
 
 

common/main.c

@@ -726,8 +726,8 @@ static void process_macros (const char *input, char *output)
 	int inputcnt  = strlen (input);
 	int outputcnt = CFG_CBSIZE;
 	int state = 0;	/* 0 = waiting for '$'	*/
-			/* 1 = waiting for '('	*/
-			/* 2 = waiting for ')'	*/
+			/* 1 = waiting for '(' or '{' */
+			/* 2 = waiting for ')' or '}' */
 			/* 3 = waiting for '''  */
 #ifdef DEBUG_PARSER
 	char *output_start = output;
@@ -765,7 +765,7 @@ static void process_macros (const char *input, char *output)
 		}
 		break;
 	    case 1:			/* Waiting for (	*/
-		if (c == '(') {
+		if (c == '(' || c == '{') {
 			state++;
 			varname_start = input;
 		} else {
@@ -780,7 +780,7 @@ static void process_macros (const char *input, char *output)
 		}
 		break;
 	    case 2:			/* Waiting for )	*/
-		if (c == ')') {
+		if (c == ')' || c == '}') {
 			int i;
 			char envname[CFG_CBSIZE], *envval;
 			int envcnt = input-varname_start-1; /* Varname # of chars */

cpu/microblaze/Makefile

@@ -0,0 +1,43 @@
+#
+# (C) Copyright 2000
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(CPU).a
+
+START	= start.o
+OBJS	= cpu.o interrupts.o
+
+all:	.depend $(START) $(LIB)
+
+$(LIB):	$(OBJS)
+	$(AR) crv $@ $(OBJS)
+
+#########################################################################
+
+.depend: Makefile $(START:.o=.S) $(OBJS:.o=.c) $(AOBJS:.o=.S)
+	$(CC) -M $(CFLAGS) $(START:.o=.S) $(OBJS:.o=.c) $(AOBJS:.o=.S) > $@
+
+sinclude .depend
+
+#########################################################################

cpu/microblaze/cpu.c

@@ -0,0 +1,25 @@
+/*
+ * (C) Copyright 2004 Atmark Techno, Inc.
+ *
+ * Yasushi SHOJI <yashi@atmark-techno.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/* EMPTY FILE */

cpu/microblaze/interrupts.c

@@ -0,0 +1,32 @@
+/*
+ * (C) Copyright 2004 Atmark Techno, Inc.
+ *
+ * Yasushi SHOJI <yashi@atmark-techno.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+void enable_interrupts(void)
+{
+}
+
+int disable_interrupts(void)
+{
+	return 0;
+}

cpu/microblaze/start.S

@@ -0,0 +1,36 @@
+/*
+ * (C) Copyright 2004 Atmark Techno, Inc.
+ *
+ * Yasushi SHOJI <yashi@atmark-techno.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+
+	.text
+	.global _start
+_start:
+
+	addi	r1, r0, CFG_SDRAM_BASE	/* init stack pointer */
+	addi	r1, r1, CFG_SDRAM_SIZE	/* set sp to high up */
+
+	brai	board_init
+
+1:	bri	1b

cpu/mpc5xxx/start.S

@@ -103,6 +103,9 @@ boot_cold:
 boot_warm:
 	mfmsr	r5			/* save msr contents		*/
 
+	/* Move CSBoot and adjust instruction pointer                   */
+	/*--------------------------------------------------------------*/
+
 #if defined(CFG_LOWBOOT)
 #if defined(CFG_RAMBOOT)
 #error CFG_LOWBOOT is incompatible with CFG_RAMBOOT
@@ -113,19 +116,15 @@ boot_warm:
 	stw	r3, 0x4(r4)		/* CS0 start */
 	lis	r3,	STOP_REG(CFG_BOOTCS_START, CFG_BOOTCS_SIZE)@h
 	ori	r3, r3, STOP_REG(CFG_BOOTCS_START, CFG_BOOTCS_SIZE)@l
-
 	stw	r3, 0x8(r4)		/* CS0 stop */
-	lis	r3,     0x00047800@h
-	ori	r3, r3, 0x00047800@l
-	stw	r3, 0x300(r4)		/* set timing, CS0/boot conf reg */
 	lis	r3,     0x02010000@h
 	ori	r3, r3, 0x02010000@l
-	stw	r3, 0x54(r4)		/* CS0 and Boot enable, IPBI ctrl reg */
+	stw	r3, 0x54(r4)		/* CS0 and Boot enable */
 
-	lis     r3,	lowboot_reentry@h
-	ori     r3, r3, lowboot_reentry@l
+	lis     r3,	lowboot_reentry@h	/* jump from bootlow address space (0x0000xxxx) */
+	ori     r3, r3, lowboot_reentry@l	/* to the address space the linker used */
 	mtlr	r3
-	blr				/* jump to flash based address */
+	blr
 
 lowboot_reentry:
 	lis	r3,	START_REG(CFG_BOOTCS_START)@h
@@ -134,12 +133,9 @@ lowboot_reentry:
 	lis	r3,	STOP_REG(CFG_BOOTCS_START, CFG_BOOTCS_SIZE)@h
 	ori	r3, r3, STOP_REG(CFG_BOOTCS_START, CFG_BOOTCS_SIZE)@l
 	stw	r3, 0x50(r4)		/* Boot stop */
-	lis	r3,     0x00047800@h
-	ori	r3, r3, 0x00047800@l
-	stw	r3, 0x300(r4)		/* set timing, CS0/boot conf reg */
 	lis	r3,     0x02000001@h
 	ori	r3, r3, 0x02000001@l
-	stw	r3, 0x54(r4)		/* Boot enable, CS0 disable, wait state enable */
+	stw	r3, 0x54(r4)		/* Boot enable, CS0 disable */
 #endif	/* CFG_LOWBOOT */
 
 #if defined(CFG_DEFAULT_MBAR) && !defined(CFG_RAMBOOT)

cpu/mpc8260/pci.c

@@ -291,8 +291,8 @@ void pci_mpc8250_init (struct pci_controller *hose)
 	immap->im_memctl.memc_pcibr0 = PCI_MSTR0_LOCAL | PCIBR_ENABLE;
 
 #ifdef CONFIG_MPC8266ADS
-	immap->im_memctl.memc_pcimsk0 = PCIMSK1_MASK;
-	immap->im_memctl.memc_pcibr0 = PCI_MSTR1_LOCAL | PCIBR_ENABLE;
+	immap->im_memctl.memc_pcimsk1 = PCIMSK1_MASK;
+	immap->im_memctl.memc_pcibr1 = PCI_MSTR1_LOCAL | PCIBR_ENABLE;
 #endif
 
 	/* Release PCI RST (by default the PCI RST signal is held low)	*/

cpu/mpc85xx/tsec.c

@@ -49,9 +49,12 @@ static int tsec_send(struct eth_device* dev, volatile void *packet, int length);
 static int tsec_recv(struct eth_device* dev);
 static int tsec_init(struct eth_device* dev, bd_t * bd);
 static void tsec_halt(struct eth_device* dev);
-static void init_registers(volatile tsec_t *regs);
-static void startup_tsec(volatile tsec_t *regs);
-static void init_phy(volatile tsec_t *regs);
+static void init_registers(tsec_t *regs);
+static void startup_tsec(tsec_t *regs);
+static void init_phy(tsec_t *regs);
+uint read_phy_reg(tsec_t *regbase, uint phyid, uint offset);
+
+static int	phy_id = -1;
 
 /* Initialize device structure.  returns 0 on failure, 1 on
  * success */
@@ -59,6 +62,7 @@ int tsec_initialize(bd_t *bis)
 {
 	struct eth_device* dev;
 	int i;
+	tsec_t *regs = (tsec_t *)(TSEC_BASE_ADDR);
 
 	dev = (struct eth_device*) malloc(sizeof *dev);
 
@@ -67,7 +71,7 @@ int tsec_initialize(bd_t *bis)
 
 	memset(dev, 0, sizeof *dev);
 
-	sprintf(dev->name, "MOTOROLA ETHERNET");
+	sprintf(dev->name, "MOTO ETHERNET");
 	dev->iobase = 0;
 	dev->priv   = 0;
 	dev->init   = tsec_init;
@@ -81,6 +85,45 @@ int tsec_initialize(bd_t *bis)
 
 	eth_register(dev);
 
+	/* Reconfigure the PHY to advertise everything here
+	 * so that it works with both gigabit and 10/100 */
+#ifdef CONFIG_PHY_M88E1011
+	/* Assign a Physical address to the TBI */
+	regs->tbipa=TBIPA_VALUE;
+
+	/* reset the management interface */
+	regs->miimcfg=MIIMCFG_RESET;
+
+	regs->miimcfg=MIIMCFG_INIT_VALUE;
+
+	/* Wait until the bus is free */
+	while(regs->miimind & MIIMIND_BUSY);
+
+	/* Locate PHYs.  Skip TBIPA, which we know is 31.
+	*/
+	for (i=0; i<31; i++) {
+		if (read_phy_reg(regs, i, 2) == 0x141) {
+			if (phy_id == -1)
+				phy_id = i;
+#ifdef TSEC_DEBUG
+			printf("Found Marvell PHY at 0x%02x\n", i);
+#endif
+		}
+	}
+#ifdef TSEC_DEBUG
+	printf("Using PHY ID 0x%02x\n", phy_id);
+#endif
+	write_phy_reg(regs, phy_id, MIIM_CONTROL, MIIM_CONTROL_RESET);
+
+	RESET_ERRATA(regs, phy_id);
+
+	/* Configure the PHY to advertise gbit and 10/100 */
+	write_phy_reg(regs, phy_id, MIIM_GBIT_CONTROL, MIIM_GBIT_CONTROL_INIT);
+	write_phy_reg(regs, phy_id, MIIM_ANAR, MIIM_ANAR_INIT);
+
+	/* Reset the PHY so the new settings take effect */
+	write_phy_reg(regs, phy_id, MIIM_CONTROL, MIIM_CONTROL_RESET);
+#endif
 	return 1;
 }
 
@@ -89,12 +132,12 @@ int tsec_initialize(bd_t *bis)
  * and brings the interface up */
 int tsec_init(struct eth_device* dev, bd_t * bd)
 {
-	volatile tsec_t *regs;
+	tsec_t *regs;
 	uint tempval;
 	char tmpbuf[MAC_ADDR_LEN];
 	int i;
 
-	regs = (volatile tsec_t *)(TSEC_BASE_ADDR);
+	regs = (tsec_t *)(TSEC_BASE_ADDR);
 
 	/* Make sure the controller is stopped */
 	tsec_halt(dev);
@@ -146,7 +189,7 @@ int tsec_init(struct eth_device* dev, bd_t * bd)
 /* and then passes those bits on to the variable specified in */
 /* value */
 /* Before it does the read, it needs to clear the command field */
-uint read_phy_reg(volatile tsec_t *regbase, uint phyid, uint offset)
+uint read_phy_reg(tsec_t *regbase, uint phyid, uint offset)
 {
 	uint value;
 
@@ -173,7 +216,7 @@ uint read_phy_reg(volatile tsec_t *regbase, uint phyid, uint offset)
 }
 
 /* Setup the PHY */
-static void init_phy(volatile tsec_t *regs)
+static void init_phy(tsec_t *regs)
 {
 	uint testval;
 	unsigned int timeout = TSEC_TIMEOUT;
@@ -198,17 +241,17 @@ static void init_phy(volatile tsec_t *regs)
 #endif
 
 	/* Set the PHY to gigabit, full duplex, Auto-negotiate */
-	write_phy_reg(regs, 0, MIIM_CONTROL, MIIM_CONTROL_INIT);
+	write_phy_reg(regs, phy_id, MIIM_CONTROL, MIIM_CONTROL_INIT);
 
-	/* Wait until TBI_STATUS indicates AN is done */
+	/* Wait until STATUS indicates Auto-Negotiation is done */
 	DBGPRINT("Waiting for Auto-negotiation to complete\n");
-	testval=read_phy_reg(regs, 0, MIIM_TBI_STATUS);
+	testval=read_phy_reg(regs, phy_id, MIIM_STATUS);
 
-	while((!(testval & MIIM_TBI_STATUS_AN_DONE))&& timeout--) {
-		testval=read_phy_reg(regs, 0, MIIM_TBI_STATUS);
+	while((!(testval & MIIM_STATUS_AN_DONE))&& timeout--) {
+		testval=read_phy_reg(regs, phy_id, MIIM_STATUS);
 	}
 
-	if(testval & MIIM_TBI_STATUS_AN_DONE)
+	if(testval & MIIM_STATUS_AN_DONE)
 		DBGPRINT("Auto-negotiation done\n");
 	else
 		DBGPRINT("Auto-negotiation timed-out.\n");
@@ -216,7 +259,7 @@ static void init_phy(volatile tsec_t *regs)
 #ifdef CONFIG_PHY_CIS8201
 	/* Find out what duplexity (duplicity?) we have */
 	/* Read it twice to make sure */
-	testval=read_phy_reg(regs, 0, MIIM_AUX_CONSTAT);
+	testval=read_phy_reg(regs, phy_id, MIIM_AUX_CONSTAT);
 
 	if(testval & MIIM_AUXCONSTAT_DUPLEX) {
 		DBGPRINT("Enet starting in full duplex\n");
@@ -246,17 +289,17 @@ static void init_phy(volatile tsec_t *regs)
 
 #ifdef CONFIG_PHY_M88E1011
 	/* Read the PHY to see what speed and duplex we are */
-	testval=read_phy_reg(regs, 0, MIIM_PHY_STATUS);
+	testval=read_phy_reg(regs, phy_id, MIIM_PHY_STATUS);
 
 	timeout = TSEC_TIMEOUT;
 	while((!(testval & MIIM_PHYSTAT_SPDDONE)) && timeout--) {
-		testval = read_phy_reg(regs,0,MIIM_PHY_STATUS);
+		testval = read_phy_reg(regs,phy_id,MIIM_PHY_STATUS);
 	}
 
 	if(!(testval & MIIM_PHYSTAT_SPDDONE))
 		DBGPRINT("Enet: Speed not resolved\n");
 
-	testval=read_phy_reg(regs, 0, MIIM_PHY_STATUS);
+	testval=read_phy_reg(regs, phy_id, MIIM_PHY_STATUS);
 	if(testval & MIIM_PHYSTAT_DUPLEX) {
 		DBGPRINT("Enet starting in Full Duplex\n");
 		regs->maccfg2 |= MACCFG2_FULL_DUPLEX;
@@ -280,7 +323,7 @@ static void init_phy(volatile tsec_t *regs)
 }
 
 
-static void init_registers(volatile tsec_t *regs)
+static void init_registers(tsec_t *regs)
 {
 	/* Clear IEVENT */
 	regs->ievent = IEVENT_INIT_CLEAR;
@@ -322,7 +365,7 @@ static void init_registers(volatile tsec_t *regs)
 
 }
 
-static void startup_tsec(volatile tsec_t *regs)
+static void startup_tsec(tsec_t *regs)
 {
 	int i;
 
@@ -363,7 +406,7 @@ static int tsec_send(struct eth_device* dev, volatile void *packet, int length)
 {
 	int i;
 	int result = 0;
-	volatile tsec_t * regs = (volatile tsec_t *)(TSEC_BASE_ADDR);
+	tsec_t * regs = (tsec_t *)(TSEC_BASE_ADDR);
 
 	/* Find an empty buffer descriptor */
 	for(i=0; rtx.txbd[txIdx].status & TXBD_READY; i++) {
@@ -397,7 +440,7 @@ static int tsec_send(struct eth_device* dev, volatile void *packet, int length)
 static int tsec_recv(struct eth_device* dev)
 {
 	int length;
-	volatile tsec_t *regs = (volatile tsec_t *)(TSEC_BASE_ADDR);
+	tsec_t *regs = (tsec_t *)(TSEC_BASE_ADDR);
 
 	while(!(rtx.rxbd[rxIdx].status & RXBD_EMPTY)) {
 
@@ -428,7 +471,7 @@ static int tsec_recv(struct eth_device* dev)
 
 static void tsec_halt(struct eth_device* dev)
 {
-	volatile tsec_t *regs = (volatile tsec_t *)(TSEC_BASE_ADDR);
+	tsec_t *regs = (tsec_t *)(TSEC_BASE_ADDR);
 
 	regs->dmactrl &= ~(DMACTRL_GRS | DMACTRL_GTS);
 	regs->dmactrl |= (DMACTRL_GRS | DMACTRL_GTS);
@@ -438,4 +481,44 @@ static void tsec_halt(struct eth_device* dev)
 	regs->maccfg1 &= ~(MACCFG1_TX_EN | MACCFG1_RX_EN);
 
 }
+
+#ifndef CONFIG_BITBANGMII
+/*
+ * Read a MII PHY register.
+ *
+ * Returns:
+ *   0 on success
+ */
+int miiphy_read(unsigned char  addr,
+		unsigned char  reg,
+		unsigned short *value)
+{
+	tsec_t *regs;
+	unsigned short rv;
+
+	regs = (tsec_t *)(TSEC_BASE_ADDR);
+	rv = (unsigned short)read_phy_reg(regs, addr, reg);
+	*value = rv;
+
+	return 0;
+}
+
+/*
+ * Write a MII PHY register.
+ *
+ * Returns:
+ *   0 on success
+ */
+int miiphy_write(unsigned char  addr,
+		 unsigned char  reg,
+		 unsigned short value)
+{
+	tsec_t *regs;
+
+	regs = (tsec_t *)(TSEC_BASE_ADDR);
+	write_phy_reg(regs, addr, reg, value);
+
+	return 0;
+}
+#endif /* CONFIG_BITBANGMII */
 #endif /* CONFIG_TSEC_ENET */

cpu/mpc85xx/tsec.h

@@ -19,6 +19,9 @@
 #include <net.h>
 #include <mpc85xx.h>
 
+/* TSEC1 is offset 0x24000, TSEC2 is offset 0x25000
+#define TSEC_BASE_ADDR	(CFG_IMMR + 0x25000)
+*/
 #define TSEC_BASE_ADDR	(CFG_IMMR + 0x24000)
 #define TSEC_MEM_SIZE	0x01000
 
@@ -56,16 +59,16 @@
 #define MIIMIND_BUSY            0x00000001
 #define MIIMIND_NOTVALID        0x00000004
 
-#define MIIM_TBICON		0x11
-#define MIIM_TBICON_GMII	0x00000010
-#define MIIM_TBICON_AN		0x00000100
-
 #define MIIM_CONTROL            0x00
 #define MIIM_CONTROL_INIT       0x00001140
 #define MIIM_ANEN               0x00001000
+#define MIIM_CONTROL_RESET	0x00009140
 
-#define MIIM_TBI_STATUS		0x1
-#define MIIM_TBI_STATUS_AN_DONE 0x00000020
+#define MIIM_STATUS		0x1
+#define MIIM_STATUS_AN_DONE 	0x00000020
+
+#define MIIM_GBIT_CONTROL	0x9
+#define MIIM_GBIT_CONTROL_INIT	0xe00
 
 #define MIIM_TBI_ANEX		0x6
 #define MIIM_TBI_ANEX_NP	0x00000004
@@ -89,11 +92,11 @@
 #endif
 
 #ifdef CONFIG_PHY_M88E1011
-#define MIIM_ANAR		0x04
-#define MIIM_ANAR_ADVERTISEMENT	0x01e1
+#define MIIM_ANAR		0x4
+#define MIIM_ANAR_INIT		0x1e1
 
 #define MIIM_GBIT_CON		0x09
-#define MIIM_GBIT_CON_ADVERT	0x1e00
+#define MIIM_GBIT_CON_ADVERT	0x0e00
 
 #define MIIM_PHY_STATUS         0x11
 #define MIIM_PHYSTAT_SPEED      0xc000
@@ -130,6 +133,15 @@
 } while(0)
 
 
+/* This works around errata in reseting the PHY */
+#define RESET_ERRATA(regs, ID) do { \
+	write_phy_reg(regs, (ID), 0x1d, 0x1f); \
+	write_phy_reg(regs, (ID), 0x1e, 0x200c); \
+	write_phy_reg(regs, (ID), 0x1d, 0x5); \
+	write_phy_reg(regs, (ID), 0x1e, 0x0); \
+	write_phy_reg(regs, (ID), 0x1e, 0x100); \
+} while(0)
+
 #define IEVENT_INIT_CLEAR	0xffffffff
 #define IEVENT_BABR		0x80000000
 #define IEVENT_RXC		0x40000000

doc/README.IceCube

@@ -1,9 +1,12 @@
 ---------------------------------------------------------------------------
 Build target                Flash address | BDI "go" command | Reset Vector
 ---------------------------------------------------------------------------
-MPC5200LITE                  0xFFF00000   |    0xFFF00100    |   0xFFF00100
-MPC5200LITE_LOWBOOT          0xFF000000   |    0xFF000100    |   0x00000100
-MPC5200LITE_LOWBOOT08        0xFF800000   |    0xFF800100    |   0x00000100
+Lite5200                     0xFFF00000   |    0xFFF00100    |   0xFFF00100
+Lite5200_LOWBOOT             0xFF000000   |    0xFF000100    |   0x00000100
+Lite5200_LOWBOOT08           0xFF800000   |    0xFF800100    |   0x00000100
+icecube_5200                 0xFFF00000   |    0xFFF00100    |   0xFFF00100
+icecube_5200_LOWBOOT         0xFF000000   |    0xFF000100    |   0x00000100
+icecube_5200_LOWBOOT08       0xFF800000   |    0xFF800100    |   0x00000100
 icecube_5200_DDR             0xFFF00000   |    0xFFF00100    |   0xFFF00100
 icecube_5200_DDR_LOWBOOT     0xFF800000   |    0xFF800100    |   0x00000100
 icecube_5200_DDR_LOWBOOT08   0xFF800000   |    0xFF800100    |   0x00000100

drivers/Makefile

@@ -37,9 +37,10 @@ OBJS	= 3c589.o 5701rls.o ali512x.o \
 	  pci.o pci_auto.o pci_indirect.o \
 	  pcnet.o plb2800_eth.o \
 	  ps2ser.o ps2mult.o pc_keyb.o keyboard.o \
-	  rtl8019.o rtl8139.o \
+	  rtl8019.o rtl8139.o rtl8169.o \
 	  s3c24x0_i2c.o sed13806.o sed156x.o \
-	  serial.o serial_max3100.o serial_pl011.o serial_pl010.o \
+	  serial.o serial_max3100.o serial_pl010.o serial_pl011.o \
+	  serial_xuartlite.o sl811_usb.o \
 	  smc91111.o smiLynxEM.o status_led.o sym53c8xx.o \
 	  ti_pci1410a.o tigon3.o w83c553f.o omap1510_i2c.o \
 	  usbdcore.o usbdcore_ep0.o usbdcore_omap1510.o usbtty.o \

drivers/pci.c

@@ -103,14 +103,14 @@ int pci_hose_write_config_##size##_via_dword(struct pci_controller *hose,\
 					     pci_dev_t dev, 		\
 					     int offset, type val)	\
 {									\
-	u32 val32, mask, ldata;						\
+	u32 val32, mask, ldata, shift;					\
 									\
 	if (pci_hose_read_config_dword(hose, dev, offset & 0xfc, &val32) < 0)\
 		return -1;						\
 									\
-	mask = val_mask;						\
-	ldata = (((unsigned long)val) & mask) << ((offset & (int)off_mask) * 8);\
-	mask <<= ((mask & (int)off_mask) * 8);				\
+	shift = ((offset & (int)off_mask) * 8);				\
+	ldata = (((unsigned long)val) & val_mask) << shift;		\
+	mask = val_mask << shift;					\
 	val32 = (val32 & ~mask) | ldata;				\
 									\
 	if (pci_hose_write_config_dword(hose, dev, offset & 0xfc, val32) < 0)\

drivers/rtl8169.c

@@ -0,0 +1,888 @@
+/*
+ * rtl8169.c : U-Boot driver for the RealTek RTL8169
+ *
+ * Masami Komiya (mkomiya@sonare.it)
+ *
+ * Most part is taken from r8169.c of etherboot
+ *
+ */
+
+/**************************************************************************
+*    r8169.c: Etherboot device driver for the RealTek RTL-8169 Gigabit
+*    Written 2003 by Timothy Legge <tlegge@rogers.com>
+*
+*    This program is free software; you can redistribute it and/or modify
+*    it under the terms of the GNU General Public License as published by
+*    the Free Software Foundation; either version 2 of the License, or
+*    (at your option) any later version.
+*
+*    This program is distributed in the hope that it will be useful,
+*    but WITHOUT ANY WARRANTY; without even the implied warranty of
+*    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+*    GNU General Public License for more details.
+*
+*    You should have received a copy of the GNU General Public License
+*    along with this program; if not, write to the Free Software
+*    Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+*
+*    Portions of this code based on:
+*	r8169.c: A RealTek RTL-8169 Gigabit Ethernet driver
+*		for Linux kernel 2.4.x.
+*
+*    Written 2002 ShuChen <shuchen@realtek.com.tw>
+*	  See Linux Driver for full information
+*
+*    Linux Driver Version 1.27a, 10.02.2002
+*
+*    Thanks to:
+*	Jean Chen of RealTek Semiconductor Corp. for
+*	providing the evaluation NIC used to develop
+*	this driver.  RealTek's support for Etherboot
+*	is appreciated.
+*
+*    REVISION HISTORY:
+*    ================
+*
+*    v1.0	11-26-2003	timlegge	Initial port of Linux driver
+*    v1.5	01-17-2004	timlegge	Initial driver output cleanup
+*
+*    Indent Options: indent -kr -i8
+***************************************************************************/
+
+#include <common.h>
+#include <malloc.h>
+#include <net.h>
+#include <asm/io.h>
+#include <pci.h>
+
+#if (CONFIG_COMMANDS & CFG_CMD_NET) && defined(CONFIG_NET_MULTI) && \
+	defined(CONFIG_RTL8169)
+
+#undef DEBUG_RTL8169
+#undef DEBUG_RTL8169_TX
+#undef DEBUG_RTL8169_RX
+
+#define drv_version "v1.5"
+#define drv_date "01-17-2004"
+
+static u32 ioaddr;
+
+/* Condensed operations for readability. */
+#define virt_to_le32desc(addr)	cpu_to_le32(virt_to_bus(addr))
+#define le32desc_to_virt(addr)	bus_to_virt(le32_to_cpu(addr))
+
+#define currticks()	get_timer(0)
+#define bus_to_phys(a)	pci_mem_to_phys((pci_dev_t)dev->priv, a)
+#define phys_to_bus(a)	pci_phys_to_mem((pci_dev_t)dev->priv, a)
+
+/* media options */
+#define MAX_UNITS 8
+static int media[MAX_UNITS] = { -1, -1, -1, -1, -1, -1, -1, -1 };
+
+/* MAC address length*/
+#define MAC_ADDR_LEN	6
+
+/* max supported gigabit ethernet frame size -- must be at least (dev->mtu+14+4).*/
+#define MAX_ETH_FRAME_SIZE	1536
+
+#define TX_FIFO_THRESH 256	/* In bytes */
+
+#define RX_FIFO_THRESH	7	/* 7 means NO threshold, Rx buffer level before first PCI xfer.	 */
+#define RX_DMA_BURST	6	/* Maximum PCI burst, '6' is 1024 */
+#define TX_DMA_BURST	6	/* Maximum PCI burst, '6' is 1024 */
+#define EarlyTxThld	0x3F	/* 0x3F means NO early transmit */
+#define RxPacketMaxSize 0x0800	/* Maximum size supported is 16K-1 */
+#define InterFrameGap	0x03	/* 3 means InterFrameGap = the shortest one */
+
+#define NUM_TX_DESC	1	/* Number of Tx descriptor registers */
+#define NUM_RX_DESC	4	/* Number of Rx descriptor registers */
+#define RX_BUF_SIZE	1536	/* Rx Buffer size */
+#define RX_BUF_LEN	8192
+
+#define RTL_MIN_IO_SIZE 0x80
+#define TX_TIMEOUT  (6*HZ)
+
+/* write/read MMIO register */
+#define RTL_W8(reg, val8)	writeb ((val8), ioaddr + (reg))
+#define RTL_W16(reg, val16)	writew ((val16), ioaddr + (reg))
+#define RTL_W32(reg, val32)	writel ((val32), ioaddr + (reg))
+#define RTL_R8(reg)		readb (ioaddr + (reg))
+#define RTL_R16(reg)		readw (ioaddr + (reg))
+#define RTL_R32(reg)		((unsigned long) readl (ioaddr + (reg)))
+
+#define ETH_FRAME_LEN	MAX_ETH_FRAME_SIZE
+#define ETH_ALEN	MAC_ADDR_LEN
+#define ETH_ZLEN	60
+
+enum RTL8169_registers {
+	MAC0 = 0,		/* Ethernet hardware address. */
+	MAR0 = 8,		/* Multicast filter. */
+	TxDescStartAddr = 0x20,
+	TxHDescStartAddr = 0x28,
+	FLASH = 0x30,
+	ERSR = 0x36,
+	ChipCmd = 0x37,
+	TxPoll = 0x38,
+	IntrMask = 0x3C,
+	IntrStatus = 0x3E,
+	TxConfig = 0x40,
+	RxConfig = 0x44,
+	RxMissed = 0x4C,
+	Cfg9346 = 0x50,
+	Config0 = 0x51,
+	Config1 = 0x52,
+	Config2 = 0x53,
+	Config3 = 0x54,
+	Config4 = 0x55,
+	Config5 = 0x56,
+	MultiIntr = 0x5C,
+	PHYAR = 0x60,
+	TBICSR = 0x64,
+	TBI_ANAR = 0x68,
+	TBI_LPAR = 0x6A,
+	PHYstatus = 0x6C,
+	RxMaxSize = 0xDA,
+	CPlusCmd = 0xE0,
+	RxDescStartAddr = 0xE4,
+	EarlyTxThres = 0xEC,
+	FuncEvent = 0xF0,
+	FuncEventMask = 0xF4,
+	FuncPresetState = 0xF8,
+	FuncForceEvent = 0xFC,
+};
+
+enum RTL8169_register_content {
+	/*InterruptStatusBits */
+	SYSErr = 0x8000,
+	PCSTimeout = 0x4000,
+	SWInt = 0x0100,
+	TxDescUnavail = 0x80,
+	RxFIFOOver = 0x40,
+	RxUnderrun = 0x20,
+	RxOverflow = 0x10,
+	TxErr = 0x08,
+	TxOK = 0x04,
+	RxErr = 0x02,
+	RxOK = 0x01,
+
+	/*RxStatusDesc */
+	RxRES = 0x00200000,
+	RxCRC = 0x00080000,
+	RxRUNT = 0x00100000,
+	RxRWT = 0x00400000,
+
+	/*ChipCmdBits */
+	CmdReset = 0x10,
+	CmdRxEnb = 0x08,
+	CmdTxEnb = 0x04,
+	RxBufEmpty = 0x01,
+
+	/*Cfg9346Bits */
+	Cfg9346_Lock = 0x00,
+	Cfg9346_Unlock = 0xC0,
+
+	/*rx_mode_bits */
+	AcceptErr = 0x20,
+	AcceptRunt = 0x10,
+	AcceptBroadcast = 0x08,
+	AcceptMulticast = 0x04,
+	AcceptMyPhys = 0x02,
+	AcceptAllPhys = 0x01,
+
+	/*RxConfigBits */
+	RxCfgFIFOShift = 13,
+	RxCfgDMAShift = 8,
+
+	/*TxConfigBits */
+	TxInterFrameGapShift = 24,
+	TxDMAShift = 8,		/* DMA burst value (0-7) is shift this many bits */
+
+	/*rtl8169_PHYstatus */
+	TBI_Enable = 0x80,
+	TxFlowCtrl = 0x40,
+	RxFlowCtrl = 0x20,
+	_1000bpsF = 0x10,
+	_100bps = 0x08,
+	_10bps = 0x04,
+	LinkStatus = 0x02,
+	FullDup = 0x01,
+
+	/*GIGABIT_PHY_registers */
+	PHY_CTRL_REG = 0,
+	PHY_STAT_REG = 1,
+	PHY_AUTO_NEGO_REG = 4,
+	PHY_1000_CTRL_REG = 9,
+
+	/*GIGABIT_PHY_REG_BIT */
+	PHY_Restart_Auto_Nego = 0x0200,
+	PHY_Enable_Auto_Nego = 0x1000,
+
+	/* PHY_STAT_REG = 1; */
+	PHY_Auto_Neco_Comp = 0x0020,
+
+	/* PHY_AUTO_NEGO_REG = 4; */
+	PHY_Cap_10_Half = 0x0020,
+	PHY_Cap_10_Full = 0x0040,
+	PHY_Cap_100_Half = 0x0080,
+	PHY_Cap_100_Full = 0x0100,
+
+	/* PHY_1000_CTRL_REG = 9; */
+	PHY_Cap_1000_Full = 0x0200,
+
+	PHY_Cap_Null = 0x0,
+
+	/*_MediaType*/
+	_10_Half = 0x01,
+	_10_Full = 0x02,
+	_100_Half = 0x04,
+	_100_Full = 0x08,
+	_1000_Full = 0x10,
+
+	/*_TBICSRBit*/
+	TBILinkOK = 0x02000000,
+};
+
+static struct {
+	const char *name;
+	u8 version;		/* depend on RTL8169 docs */
+	u32 RxConfigMask;	/* should clear the bits supported by this chip */
+} rtl_chip_info[] = {
+	{"RTL-8169", 0x00, 0xff7e1880,},
+	{"RTL-8169", 0x04, 0xff7e1880,},
+};
+
+enum _DescStatusBit {
+	OWNbit = 0x80000000,
+	EORbit = 0x40000000,
+	FSbit = 0x20000000,
+	LSbit = 0x10000000,
+};
+
+struct TxDesc {
+	u32 status;
+	u32 vlan_tag;
+	u32 buf_addr;
+	u32 buf_Haddr;
+};
+
+struct RxDesc {
+	u32 status;
+	u32 vlan_tag;
+	u32 buf_addr;
+	u32 buf_Haddr;
+};
+
+/* Define the TX Descriptor */
+static u8 tx_ring[NUM_TX_DESC * sizeof(struct TxDesc) + 256];
+/*	__attribute__ ((aligned(256))); */
+
+/* Create a static buffer of size RX_BUF_SZ for each
+TX Descriptor.	All descriptors point to a
+part of this buffer */
+static unsigned char txb[NUM_TX_DESC * RX_BUF_SIZE];
+
+/* Define the RX Descriptor */
+static u8 rx_ring[NUM_RX_DESC * sizeof(struct TxDesc) + 256];
+  /*  __attribute__ ((aligned(256))); */
+
+/* Create a static buffer of size RX_BUF_SZ for each
+RX Descriptor	All descriptors point to a
+part of this buffer */
+static unsigned char rxb[NUM_RX_DESC * RX_BUF_SIZE];
+
+struct rtl8169_private {
+	void *mmio_addr;	/* memory map physical address */
+	int chipset;
+	unsigned long cur_rx;	/* Index into the Rx descriptor buffer of next Rx pkt. */
+	unsigned long cur_tx;	/* Index into the Tx descriptor buffer of next Rx pkt. */
+	unsigned long dirty_tx;
+	unsigned char *TxDescArrays;	/* Index of Tx Descriptor buffer */
+	unsigned char *RxDescArrays;	/* Index of Rx Descriptor buffer */
+	struct TxDesc *TxDescArray;	/* Index of 256-alignment Tx Descriptor buffer */
+	struct RxDesc *RxDescArray;	/* Index of 256-alignment Rx Descriptor buffer */
+	unsigned char *RxBufferRings;	/* Index of Rx Buffer  */
+	unsigned char *RxBufferRing[NUM_RX_DESC];	/* Index of Rx Buffer array */
+	unsigned char *Tx_skbuff[NUM_TX_DESC];
+} tpx;
+
+static struct rtl8169_private *tpc;
+
+static const u16 rtl8169_intr_mask =
+    SYSErr | PCSTimeout | RxUnderrun | RxOverflow | RxFIFOOver | TxErr |
+    TxOK | RxErr | RxOK;
+static const unsigned int rtl8169_rx_config =
+    (RX_FIFO_THRESH << RxCfgFIFOShift) | (RX_DMA_BURST << RxCfgDMAShift);
+
+static struct pci_device_id supported[] = {
+	{PCI_VENDOR_ID_REALTEK, 0x8169},
+	{}
+};
+
+void mdio_write(int RegAddr, int value)
+{
+	int i;
+
+	RTL_W32(PHYAR, 0x80000000 | (RegAddr & 0xFF) << 16 | value);
+	udelay(1000);
+
+	for (i = 2000; i > 0; i--) {
+		/* Check if the RTL8169 has completed writing to the specified MII register */
+		if (!(RTL_R32(PHYAR) & 0x80000000)) {
+			break;
+		} else {
+			udelay(100);
+		}
+	}
+}
+
+int mdio_read(int RegAddr)
+{
+	int i, value = -1;
+
+	RTL_W32(PHYAR, 0x0 | (RegAddr & 0xFF) << 16);
+	udelay(1000);
+
+	for (i = 2000; i > 0; i--) {
+		/* Check if the RTL8169 has completed retrieving data from the specified MII register */
+		if (RTL_R32(PHYAR) & 0x80000000) {
+			value = (int) (RTL_R32(PHYAR) & 0xFFFF);
+			break;
+		} else {
+			udelay(100);
+		}
+	}
+	return value;
+}
+
+#define ARRAY_SIZE(x) (sizeof(x) / sizeof((x)[0]))
+
+static int rtl8169_init_board(struct eth_device *dev)
+{
+	int i;
+	u32 tmp;
+
+#ifdef DEBUG_RTL8169
+	printf ("%s\n", __FUNCTION__);
+#endif
+	ioaddr = dev->iobase;
+
+	/* Soft reset the chip. */
+	RTL_W8(ChipCmd, CmdReset);
+
+	/* Check that the chip has finished the reset. */
+	for (i = 1000; i > 0; i--)
+		if ((RTL_R8(ChipCmd) & CmdReset) == 0)
+			break;
+		else
+			udelay(10);
+
+	/* identify chip attached to board */
+	tmp = RTL_R32(TxConfig);
+	tmp = ((tmp & 0x7c000000) + ((tmp & 0x00800000) << 2)) >> 24;
+
+	for (i = ARRAY_SIZE(rtl_chip_info) - 1; i >= 0; i--){
+		if (tmp == rtl_chip_info[i].version) {
+			tpc->chipset = i;
+			goto match;
+		}
+	}
+
+	/* if unknown chip, assume array element #0, original RTL-8169 in this case */
+	printf("PCI device %s: unknown chip version, assuming RTL-8169\n", dev->name);
+	printf("PCI device: TxConfig = 0x%hX\n", (unsigned long) RTL_R32(TxConfig));
+	tpc->chipset = 0;
+
+match:
+	return 0;
+}
+
+/**************************************************************************
+RECV - Receive a frame
+***************************************************************************/
+static int rtl_recv(struct eth_device *dev)
+{
+	/* return true if there's an ethernet packet ready to read */
+	/* nic->packet should contain data on return */
+	/* nic->packetlen should contain length of data */
+	int cur_rx;
+	int length = 0;
+
+#ifdef DEBUG_RTL8169_RX
+	printf ("%s\n", __FUNCTION__);
+#endif
+	ioaddr = dev->iobase;
+
+	cur_rx = tpc->cur_rx;
+	if ((tpc->RxDescArray[cur_rx].status & OWNbit) == 0) {
+		if (!(tpc->RxDescArray[cur_rx].status & RxRES)) {
+			unsigned char rxdata[RX_BUF_LEN];
+			length = (int) (tpc->RxDescArray[cur_rx].
+						status & 0x00001FFF) - 4;
+
+			memcpy(rxdata, tpc->RxBufferRing[cur_rx], length);
+			NetReceive(rxdata, length);
+
+			if (cur_rx == NUM_RX_DESC - 1)
+				tpc->RxDescArray[cur_rx].status =
+				    (OWNbit | EORbit) + RX_BUF_SIZE;
+			else
+				tpc->RxDescArray[cur_rx].status =
+				    OWNbit + RX_BUF_SIZE;
+			tpc->RxDescArray[cur_rx].buf_addr =
+			    virt_to_bus(tpc->RxBufferRing[cur_rx]);
+		} else {
+			puts("Error Rx");
+		}
+		cur_rx = (cur_rx + 1) % NUM_RX_DESC;
+		tpc->cur_rx = cur_rx;
+		return 1;
+
+	}
+	tpc->cur_rx = cur_rx;
+	return (0);		/* initially as this is called to flush the input */
+}
+
+#define HZ 1000
+/**************************************************************************
+SEND - Transmit a frame
+***************************************************************************/
+static int rtl_send(struct eth_device *dev, volatile void *packet, int length)
+{
+	/* send the packet to destination */
+
+	u32 to;
+	u8 *ptxb;
+	int entry = tpc->cur_tx % NUM_TX_DESC;
+	u32 len = length;
+
+#ifdef DEBUG_RTL8169_TX
+	int stime = currticks();
+	printf ("%s\n", __FUNCTION__);
+	printf("sending %d bytes\n", len);
+#endif
+
+	ioaddr = dev->iobase;
+
+	/* point to the current txb incase multiple tx_rings are used */
+	ptxb = tpc->Tx_skbuff[entry * MAX_ETH_FRAME_SIZE];
+	memcpy(ptxb, (char *)packet, (int)length);
+
+	while (len < ETH_ZLEN)
+		ptxb[len++] = '\0';
+
+	tpc->TxDescArray[entry].buf_addr = virt_to_bus(ptxb);
+	if (entry != (NUM_TX_DESC - 1)) {
+		tpc->TxDescArray[entry].status =
+		    (OWNbit | FSbit | LSbit) | ((len > ETH_ZLEN) ?
+						len : ETH_ZLEN);
+	} else {
+		tpc->TxDescArray[entry].status =
+		    (OWNbit | EORbit | FSbit | LSbit) |
+		    ((len > ETH_ZLEN) ? length : ETH_ZLEN);
+	}
+	RTL_W8(TxPoll, 0x40);	/* set polling bit */
+
+	tpc->cur_tx++;
+	to = currticks() + TX_TIMEOUT;
+	while ((tpc->TxDescArray[entry].status & OWNbit) && (currticks() < to));	/* wait */
+
+	if (currticks() >= to) {
+#ifdef DEBUG_RTL8169_TX
+		puts ("tx timeout/error\n");
+		printf ("%s elapsed time : %d\n", __FUNCTION__, currticks()-stime);
+#endif
+		return 0;
+	} else {
+#ifdef DEBUG_RTL8169_TX
+		puts("tx done\n");
+#endif
+		return length;
+	}
+}
+
+static void rtl8169_set_rx_mode(struct eth_device *dev)
+{
+	u32 mc_filter[2];	/* Multicast hash filter */
+	int rx_mode;
+	u32 tmp = 0;
+
+#ifdef DEBUG_RTL8169
+	printf ("%s\n", __FUNCTION__);
+#endif
+
+	/* IFF_ALLMULTI */
+	/* Too many to filter perfectly -- accept all multicasts. */
+	rx_mode = AcceptBroadcast | AcceptMulticast | AcceptMyPhys;
+	mc_filter[1] = mc_filter[0] = 0xffffffff;
+
+	tmp = rtl8169_rx_config | rx_mode | (RTL_R32(RxConfig) &
+				   rtl_chip_info[tpc->chipset].RxConfigMask);
+
+	RTL_W32(RxConfig, tmp);
+	RTL_W32(MAR0 + 0, mc_filter[0]);
+	RTL_W32(MAR0 + 4, mc_filter[1]);
+}
+
+static void rtl8169_hw_start(struct eth_device *dev)
+{
+	u32 i;
+
+#ifdef DEBUG_RTL8169
+	int stime = currticks();
+	printf ("%s\n", __FUNCTION__);
+#endif
+
+#if 0
+	/* Soft reset the chip. */
+	RTL_W8(ChipCmd, CmdReset);
+
+	/* Check that the chip has finished the reset. */
+	for (i = 1000; i > 0; i--) {
+		if ((RTL_R8(ChipCmd) & CmdReset) == 0)
+			break;
+		else
+			udelay(10);
+	}
+#endif
+
+	RTL_W8(Cfg9346, Cfg9346_Unlock);
+	RTL_W8(ChipCmd, CmdTxEnb | CmdRxEnb);
+	RTL_W8(EarlyTxThres, EarlyTxThld);
+
+	/* For gigabit rtl8169 */
+	RTL_W16(RxMaxSize, RxPacketMaxSize);
+
+	/* Set Rx Config register */
+	i = rtl8169_rx_config | (RTL_R32(RxConfig) &
+				 rtl_chip_info[tpc->chipset].RxConfigMask);
+	RTL_W32(RxConfig, i);
+
+	/* Set DMA burst size and Interframe Gap Time */
+	RTL_W32(TxConfig, (TX_DMA_BURST << TxDMAShift) |
+				(InterFrameGap << TxInterFrameGapShift));
+
+
+	tpc->cur_rx = 0;
+
+	RTL_W32(TxDescStartAddr, virt_to_le32desc(tpc->TxDescArray));
+	RTL_W32(RxDescStartAddr, virt_to_le32desc(tpc->RxDescArray));
+	RTL_W8(Cfg9346, Cfg9346_Lock);
+	udelay(10);
+
+	RTL_W32(RxMissed, 0);
+
+	rtl8169_set_rx_mode(dev);
+
+	/* no early-rx interrupts */
+	RTL_W16(MultiIntr, RTL_R16(MultiIntr) & 0xF000);
+
+#ifdef DEBUG_RTL8169
+	printf ("%s elapsed time : %d\n", __FUNCTION__, currticks()-stime);
+#endif
+}
+
+static void rtl8169_init_ring(struct eth_device *dev)
+{
+	int i;
+
+#ifdef DEBUG_RTL8169
+	int stime = currticks();
+	printf ("%s\n", __FUNCTION__);
+#endif
+
+	tpc->cur_rx = 0;
+	tpc->cur_tx = 0;
+	tpc->dirty_tx = 0;
+	memset(tpc->TxDescArray, 0x0, NUM_TX_DESC * sizeof(struct TxDesc));
+	memset(tpc->RxDescArray, 0x0, NUM_RX_DESC * sizeof(struct RxDesc));
+
+	for (i = 0; i < NUM_TX_DESC; i++) {
+		tpc->Tx_skbuff[i] = &txb[i];
+	}
+
+	for (i = 0; i < NUM_RX_DESC; i++) {
+		if (i == (NUM_RX_DESC - 1))
+			tpc->RxDescArray[i].status =
+			    (OWNbit | EORbit) + RX_BUF_SIZE;
+		else
+			tpc->RxDescArray[i].status = OWNbit + RX_BUF_SIZE;
+
+		tpc->RxBufferRing[i] = &rxb[i * RX_BUF_SIZE];
+		tpc->RxDescArray[i].buf_addr =
+		    virt_to_bus(tpc->RxBufferRing[i]);
+	}
+
+#ifdef DEBUG_RTL8169
+	printf ("%s elapsed time : %d\n", __FUNCTION__, currticks()-stime);
+#endif
+}
+
+/**************************************************************************
+RESET - Finish setting up the ethernet interface
+***************************************************************************/
+static void rtl_reset(struct eth_device *dev, bd_t *bis)
+{
+	int i;
+	u8 diff;
+	u32 TxPhyAddr, RxPhyAddr;
+
+#ifdef DEBUG_RTL8169
+	int stime = currticks();
+	printf ("%s\n", __FUNCTION__);
+#endif
+
+	tpc->TxDescArrays = tx_ring;
+	if (tpc->TxDescArrays == 0)
+		puts("Allot Error");
+	/* Tx Desscriptor needs 256 bytes alignment; */
+	TxPhyAddr = virt_to_bus(tpc->TxDescArrays);
+	diff = 256 - (TxPhyAddr - ((TxPhyAddr >> 8) << 8));
+	TxPhyAddr += diff;
+	tpc->TxDescArray = (struct TxDesc *) (tpc->TxDescArrays + diff);
+
+	tpc->RxDescArrays = rx_ring;
+	/* Rx Desscriptor needs 256 bytes alignment; */
+	RxPhyAddr = virt_to_bus(tpc->RxDescArrays);
+	diff = 256 - (RxPhyAddr - ((RxPhyAddr >> 8) << 8));
+	RxPhyAddr += diff;
+	tpc->RxDescArray = (struct RxDesc *) (tpc->RxDescArrays + diff);
+
+	if (tpc->TxDescArrays == NULL || tpc->RxDescArrays == NULL) {
+		puts("Allocate RxDescArray or TxDescArray failed\n");
+		return;
+	}
+
+	rtl8169_init_ring(dev);
+	rtl8169_hw_start(dev);
+	/* Construct a perfect filter frame with the mac address as first match
+	 * and broadcast for all others */
+	for (i = 0; i < 192; i++)
+		txb[i] = 0xFF;
+
+	txb[0] = dev->enetaddr[0];
+	txb[1] = dev->enetaddr[1];
+	txb[2] = dev->enetaddr[2];
+	txb[3] = dev->enetaddr[3];
+	txb[4] = dev->enetaddr[4];
+	txb[5] = dev->enetaddr[5];
+
+#ifdef DEBUG_RTL8169
+	printf ("%s elapsed time : %d\n", __FUNCTION__, currticks()-stime);
+#endif
+}
+
+/**************************************************************************
+HALT - Turn off ethernet interface
+***************************************************************************/
+static void rtl_halt(struct eth_device *dev)
+{
+	int i;
+
+#ifdef DEBUG_RTL8169
+	printf ("%s\n", __FUNCTION__);
+#endif
+
+	ioaddr = dev->iobase;
+
+	/* Stop the chip's Tx and Rx DMA processes. */
+	RTL_W8(ChipCmd, 0x00);
+
+	/* Disable interrupts by clearing the interrupt mask. */
+	RTL_W16(IntrMask, 0x0000);
+
+	RTL_W32(RxMissed, 0);
+
+	tpc->TxDescArrays = NULL;
+	tpc->RxDescArrays = NULL;
+	tpc->TxDescArray = NULL;
+	tpc->RxDescArray = NULL;
+	for (i = 0; i < NUM_RX_DESC; i++) {
+		tpc->RxBufferRing[i] = NULL;
+	}
+}
+
+/**************************************************************************
+INIT - Look for an adapter, this routine's visible to the outside
+***************************************************************************/
+
+#define board_found 1
+#define valid_link 0
+static int rtl_init(struct eth_device *dev, bd_t *bis)
+{
+	static int board_idx = -1;
+	static int printed_version = 0;
+	int i, rc;
+	int option = -1, Cap10_100 = 0, Cap1000 = 0;
+
+#ifdef DEBUG_RTL8169
+	printf ("%s\n", __FUNCTION__);
+#endif
+
+	ioaddr = dev->iobase;
+
+	board_idx++;
+
+	printed_version = 1;
+
+	/* point to private storage */
+	tpc = &tpx;
+
+	rc = rtl8169_init_board(dev);
+	if (rc)
+		return rc;
+
+	/* Get MAC address.  FIXME: read EEPROM */
+	for (i = 0; i < MAC_ADDR_LEN; i++)
+		dev->enetaddr[i] = RTL_R8(MAC0 + i);
+
+#ifdef DEBUG_RTL8169
+	printf("MAC Address");
+	for (i = 0; i < MAC_ADDR_LEN; i++)
+		printf(":%02x", dev->enetaddr[i]);
+	putc('\n');
+#endif
+
+#ifdef DEBUG_RTL8169
+	/* Print out some hardware info */
+	printf("%s: at ioaddr 0x%x\n", dev->name, ioaddr);
+#endif
+
+	/* if TBI is not endbled */
+	if (!(RTL_R8(PHYstatus) & TBI_Enable)) {
+		int val = mdio_read(PHY_AUTO_NEGO_REG);
+
+		option = (board_idx >= MAX_UNITS) ? 0 : media[board_idx];
+		/* Force RTL8169 in 10/100/1000 Full/Half mode. */
+		if (option > 0) {
+#ifdef DEBUG_RTL8169
+			printf("%s: Force-mode Enabled.\n", dev->name);
+#endif
+			Cap10_100 = 0, Cap1000 = 0;
+			switch (option) {
+			case _10_Half:
+				Cap10_100 = PHY_Cap_10_Half;
+				Cap1000 = PHY_Cap_Null;
+				break;
+			case _10_Full:
+				Cap10_100 = PHY_Cap_10_Full;
+				Cap1000 = PHY_Cap_Null;
+				break;
+			case _100_Half:
+				Cap10_100 = PHY_Cap_100_Half;
+				Cap1000 = PHY_Cap_Null;
+				break;
+			case _100_Full:
+				Cap10_100 = PHY_Cap_100_Full;
+				Cap1000 = PHY_Cap_Null;
+				break;
+			case _1000_Full:
+				Cap10_100 = PHY_Cap_Null;
+				Cap1000 = PHY_Cap_1000_Full;
+				break;
+			default:
+				break;
+			}
+			mdio_write(PHY_AUTO_NEGO_REG, Cap10_100 | (val & 0x1F));	/* leave PHY_AUTO_NEGO_REG bit4:0 unchanged */
+			mdio_write(PHY_1000_CTRL_REG, Cap1000);
+		} else {
+#ifdef DEBUG_RTL8169
+			printf("%s: Auto-negotiation Enabled.\n",
+			       dev->name);
+#endif
+			/* enable 10/100 Full/Half Mode, leave PHY_AUTO_NEGO_REG bit4:0 unchanged */
+			mdio_write(PHY_AUTO_NEGO_REG,
+				   PHY_Cap_10_Half | PHY_Cap_10_Full |
+				   PHY_Cap_100_Half | PHY_Cap_100_Full |
+				   (val & 0x1F));
+
+			/* enable 1000 Full Mode */
+			mdio_write(PHY_1000_CTRL_REG, PHY_Cap_1000_Full);
+
+		}
+
+		/* Enable auto-negotiation and restart auto-nigotiation */
+		mdio_write(PHY_CTRL_REG,
+			   PHY_Enable_Auto_Nego | PHY_Restart_Auto_Nego);
+		udelay(100);
+
+		/* wait for auto-negotiation process */
+		for (i = 10000; i > 0; i--) {
+			/* check if auto-negotiation complete */
+			if (mdio_read(PHY_STAT_REG) & PHY_Auto_Neco_Comp) {
+				udelay(100);
+				option = RTL_R8(PHYstatus);
+				if (option & _1000bpsF) {
+#ifdef DEBUG_RTL8169
+					printf("%s: 1000Mbps Full-duplex operation.\n",
+					     dev->name);
+#endif
+				} else {
+#ifdef DEBUG_RTL8169
+					printf
+					    ("%s: %sMbps %s-duplex operation.\n",
+					     dev->name,
+					     (option & _100bps) ? "100" :
+					     "10",
+					     (option & FullDup) ? "Full" :
+					     "Half");
+#endif
+				}
+				break;
+			} else {
+				udelay(100);
+			}
+		}		/* end for-loop to wait for auto-negotiation process */
+
+	} else {
+		udelay(100);
+#ifdef DEBUG_RTL8169
+		printf
+		    ("%s: 1000Mbps Full-duplex operation, TBI Link %s!\n",
+		     dev->name,
+		     (RTL_R32(TBICSR) & TBILinkOK) ? "OK" : "Failed");
+#endif
+	}
+
+	return 1;
+}
+
+int rtl8169_initialize(bd_t *bis)
+{
+	pci_dev_t devno;
+	int card_number = 0;
+	struct eth_device *dev;
+	u32 iobase;
+	int idx=0;
+
+	while(1){
+		/* Find RTL8169 */
+		if ((devno = pci_find_devices(supported, idx++)) < 0)
+			break;
+
+		pci_read_config_dword(devno, PCI_BASE_ADDRESS_1, &iobase);
+		iobase &= ~0xf;
+
+		debug ("rtl8169: REALTEK RTL8169 @0x%x\n", iobase);
+
+		dev = (struct eth_device *)malloc(sizeof *dev);
+
+		sprintf (dev->name, "RTL8169#%d", card_number);
+
+		dev->priv = (void *) devno;
+		dev->iobase = (int)bus_to_phys(iobase);
+
+		dev->init = rtl_reset;
+		dev->halt = rtl_halt;
+		dev->send = rtl_send;
+		dev->recv = rtl_recv;
+
+		eth_register (dev);
+
+		rtl_init(dev, bis);
+
+		card_number++;
+	}
+	return card_number;
+}
+
+#endif

drivers/serial_xuartlite.c

@@ -0,0 +1,77 @@
+/*
+ * (C) Copyright 2004 Atmark Techno, Inc.
+ *
+ * Yasushi SHOJI <yashi@atmark-techno.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+
+#ifdef	CONFIG_MICROBLZE
+
+#include <asm/serial_xuartlite.h>
+
+/* FIXME: we should convert these to in32 and out32 */
+#define IO_WORD(offset)	     (*(volatile unsigned long *)(offset))
+#define IO_SERIAL(offset)    IO_WORD(CONFIG_SERIAL_BASE + (offset))
+
+#define IO_SERIAL_RX_FIFO   IO_SERIAL(XUL_RX_FIFO_OFFSET)
+#define IO_SERIAL_TX_FIFO   IO_SERIAL(XUL_TX_FIFO_OFFSET)
+#define IO_SERIAL_STATUS    IO_SERIAL(XUL_STATUS_REG_OFFSET)
+#define IO_SERIAL_CONTROL   IO_SERIAL(XUL_CONTROL_REG_OFFSET)
+
+int serial_init(void)
+{
+	/* FIXME: Nothing for now. We should initialize fifo, etc */
+	return 0;
+}
+
+void serial_setbrg(void)
+{
+	/* FIXME: what's this for? */
+}
+
+void serial_putc(const char c)
+{
+	if (c == '\n') serial_putc('\r');
+	while (IO_SERIAL_STATUS & XUL_SR_TX_FIFO_FULL);
+	IO_SERIAL_TX_FIFO = (unsigned char) (c & 0xff);
+	return 0;
+}
+
+void serial_puts(const char * s)
+{
+	while (*s) {
+		serial_putc(*s++);
+	}
+}
+
+int serial_getc(void)
+{
+	while (!(IO_SERIAL_STATUS & XUL_SR_RX_FIFO_VALID_DATA));
+	return IO_SERIAL_RX_FIFO & 0xff;
+}
+
+int serial_tstc(void)
+{
+	return (IO_SERIAL_STATUS & XUL_SR_RX_FIFO_VALID_DATA);
+}
+
+#endif	/* CONFIG_MICROBLZE */

drivers/sl811.h

@@ -0,0 +1,104 @@
+#ifndef __UBOOT_SL811_H
+#define __UBOOT_SL811_H
+
+#undef SL811_DEBUG
+
+#ifdef SL811_DEBUG
+	#define PDEBUG(level, fmt, args...) \
+		if (debug >= (level)) printf("[%s:%d] " fmt, \
+		__PRETTY_FUNCTION__, __LINE__ , ## args)
+#else
+	#define PDEBUG(level, fmt, args...) do {} while(0)
+#endif
+
+/* Sl811 host control register */
+#define	SL811_CTRL_A		0x00
+#define	SL811_ADDR_A		0x01
+#define	SL811_LEN_A		0x02
+#define	SL811_STS_A		0x03	/* read	*/
+#define	SL811_PIDEP_A		0x03	/* write */
+#define	SL811_CNT_A		0x04	/* read	*/
+#define	SL811_DEV_A		0x04	/* write */
+#define	SL811_CTRL1		0x05
+#define	SL811_INTR		0x06
+#define	SL811_CTRL_B		0x08
+#define	SL811_ADDR_B		0x09
+#define	SL811_LEN_B		0x0A
+#define	SL811_STS_B		0x0B	/* read	*/
+#define	SL811_PIDEP_B		0x0B	/* write */
+#define	SL811_CNT_B		0x0C	/* read	*/
+#define	SL811_DEV_B		0x0C	/* write */
+#define	SL811_INTRSTS		0x0D	/* write clears	bitwise	*/
+#define	SL811_HWREV		0x0E	/* read	*/
+#define	SL811_SOFLOW		0x0E	/* write */
+#define	SL811_SOFCNTDIV		0x0F	/* read	*/
+#define	SL811_CTRL2		0x0F	/* write */
+
+/* USB control register bits (addr 0x00 and addr 0x08) */
+#define	SL811_USB_CTRL_ARM	0x01
+#define	SL811_USB_CTRL_ENABLE	0x02
+#define	SL811_USB_CTRL_DIR_OUT	0x04
+#define	SL811_USB_CTRL_ISO	0x10
+#define	SL811_USB_CTRL_SOF	0x20
+#define	SL811_USB_CTRL_TOGGLE_1	0x40
+#define	SL811_USB_CTRL_PREAMBLE	0x80
+
+/* USB status register bits (addr 0x03 and addr 0x0B) */
+#define	SL811_USB_STS_ACK	0x01
+#define	SL811_USB_STS_ERROR	0x02
+#define	SL811_USB_STS_TIMEOUT	0x04
+#define	SL811_USB_STS_TOGGLE_1	0x08
+#define	SL811_USB_STS_SETUP	0x10
+#define	SL811_USB_STS_OVERFLOW	0x20
+#define	SL811_USB_STS_NAK	0x40
+#define	SL811_USB_STS_STALL	0x80
+
+/* Control register 1 bits (addr 0x05) */
+#define	SL811_CTRL1_SOF		0x01
+#define	SL811_CTRL1_RESET	0x08
+#define	SL811_CTRL1_JKSTATE	0x10
+#define	SL811_CTRL1_SPEED_LOW	0x20
+#define	SL811_CTRL1_SUSPEND	0x40
+
+/* Interrut enable (addr 0x06) and interrupt status register bits (addr 0x0D) */
+#define	SL811_INTR_DONE_A	0x01
+#define	SL811_INTR_DONE_B	0x02
+#define	SL811_INTR_SOF		0x10
+#define	SL811_INTR_INSRMV	0x20
+#define	SL811_INTR_DETECT	0x40
+#define	SL811_INTR_NOTPRESENT	0x40
+#define	SL811_INTR_SPEED_FULL	0x80    /* only in status reg */
+
+/* HW rev and SOF lo register bits (addr 0x0E) */
+#define	SL811_HWR_HWREV		0xF0
+
+/* SOF counter and control reg 2 (addr 0x0F) */
+#define	SL811_CTL2_SOFHI	0x3F
+#define	SL811_CTL2_DSWAP	0x40
+#define	SL811_CTL2_HOST		0x80
+
+/* Set up for 1-ms SOF time. */
+#define SL811_12M_LOW		0xE0
+#define SL811_12M_HI		0x2E
+
+#define SL811_DATA_START	0x10
+#define SL811_DATA_LIMIT	240
+
+/* Requests: bRequest << 8 | bmRequestType */
+#define RH_GET_STATUS           0x0080
+#define RH_CLEAR_FEATURE        0x0100
+#define RH_SET_FEATURE          0x0300
+#define RH_SET_ADDRESS		0x0500
+#define RH_GET_DESCRIPTOR	0x0680
+#define RH_SET_DESCRIPTOR       0x0700
+#define RH_GET_CONFIGURATION	0x0880
+#define RH_SET_CONFIGURATION	0x0900
+#define RH_GET_STATE            0x0280
+#define RH_GET_INTERFACE        0x0A80
+#define RH_SET_INTERFACE        0x0B00
+#define RH_SYNC_FRAME           0x0C80
+
+
+#define PIDEP(pid, ep) (((pid) & 0x0f) << 4 | (ep))
+
+#endif	/* __UBOOT_SL811_H */

drivers/sl811_usb.c

@@ -0,0 +1,705 @@
+/*
+ * (C) Copyright 2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * This code is based on linux driver for sl811hs chip, source at
+ * drivers/usb/host/sl811.c:
+ *
+ * SL811 Host Controller Interface driver for USB.
+ *
+ * Copyright (c) 2003/06, Courage Co., Ltd.
+ *
+ * Based on:
+ *	1.uhci.c by Linus Torvalds, Johannes Erdfelt, Randy Dunlap,
+ *	  Georg Acher, Deti Fliegl, Thomas Sailer, Roman Weissgaerber,
+ *	  Adam Richter, Gregory P. Smith;
+ *	2.Original SL811 driver (hc_sl811.o) by Pei Liu <pbl@cypress.com>
+ *	3.Rewrited as sl811.o by Yin Aihua <yinah:couragetech.com.cn>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#ifdef CONFIG_USB_SL811HS
+#include <mpc8xx.h>
+#include <usb.h>
+#include "sl811.h"
+
+#include "../board/kup/common/kup.h"
+
+#ifdef __PPC__
+# define EIEIO		__asm__ volatile ("eieio")
+#else
+# define EIEIO		/* nothing */
+#endif
+
+#define	 SL811_ADR (0x50000000)
+#define	 SL811_DAT (0x50000001)
+
+#define mdelay(n) ({unsigned long msec=(n); while (msec--) udelay(1000);})
+
+#ifdef SL811_DEBUG
+static int debug = 9;
+#endif
+
+static int root_hub_devnum = 0;
+static struct usb_port_status rh_status = { 0 };/* root hub port status */
+
+static int sl811_rh_submit_urb(struct usb_device *usb_dev, unsigned long pipe,
+			       void *data, int buf_len, struct devrequest *cmd);
+
+static void sl811_write (__u8 index, __u8 data)
+{
+	*(volatile unsigned char *) (SL811_ADR) = index;
+	EIEIO;
+	*(volatile unsigned char *) (SL811_DAT) = data;
+	EIEIO;
+}
+
+static __u8 sl811_read (__u8 index)
+{
+	__u8 data;
+
+	*(volatile unsigned char *) (SL811_ADR) = index;
+	EIEIO;
+	data = *(volatile unsigned char *) (SL811_DAT);
+	EIEIO;
+	return (data);
+}
+
+/*
+ * Read consecutive bytes of data from the SL811H/SL11H buffer
+ */
+static void inline sl811_read_buf(__u8 offset, __u8 *buf, __u8 size)
+{
+	*(volatile unsigned char *) (SL811_ADR) = offset;
+	EIEIO;
+	while (size--) {
+		*buf++ = *(volatile unsigned char *) (SL811_DAT);
+		EIEIO;
+	}
+}
+
+/*
+ * Write consecutive bytes of data to the SL811H/SL11H buffer
+ */
+static void inline sl811_write_buf(__u8 offset, __u8 *buf, __u8 size)
+{
+	*(volatile unsigned char *) (SL811_ADR) = offset;
+	EIEIO;
+	while (size--) {
+		*(volatile unsigned char *) (SL811_DAT) = *buf++;
+		EIEIO;
+	}
+}
+
+int usb_init_kup4x (void)
+{
+	volatile immap_t *immap = (immap_t *) CFG_IMMR;
+	volatile memctl8xx_t *memctl = &immap->im_memctl;
+	int i;
+	unsigned char tmp;
+
+	memctl = &immap->im_memctl;
+	memctl->memc_or7 = 0xFFFF8726;
+	memctl->memc_br7 = 0x50000401;	/* start at 0x50000000 */
+	/* BP 14 low = USB ON */
+	immap->im_cpm.cp_pbdat &= ~(BP_USB_VCC);
+	/* PB 14 nomal port */
+	immap->im_cpm.cp_pbpar &= ~(BP_USB_VCC);
+	/* output */
+	immap->im_cpm.cp_pbdir |= (BP_USB_VCC);
+
+	puts ("USB:   ");
+
+	for (i = 0x10; i < 0xff; i++) {
+		sl811_write(i, i);
+		tmp = (sl811_read(i));
+		if (tmp != i) {
+			printf ("SL811 compare error index=0x%02x read=0x%02x\n", i, tmp);
+			return (-1);
+		}
+	}
+	printf ("SL811 ready\n");
+	return (0);
+}
+
+/*
+ * This function resets SL811HS controller and detects the speed of
+ * the connecting device
+ *
+ * Return: 0 = no device attached; 1 = USB device attached
+ */
+static int sl811_hc_reset(void)
+{
+	int status ;
+
+	sl811_write(SL811_CTRL2, SL811_CTL2_HOST | SL811_12M_HI);
+	sl811_write(SL811_CTRL1, SL811_CTRL1_RESET);
+
+	mdelay(20);
+
+	/* Disable hardware SOF generation, clear all irq status. */
+	sl811_write(SL811_CTRL1, 0);
+	mdelay(2);
+	sl811_write(SL811_INTRSTS, 0xff);
+	status = sl811_read(SL811_INTRSTS);
+
+	if (status & SL811_INTR_NOTPRESENT) {
+		/* Device is not present */
+		PDEBUG(0, "Device not present\n");
+		rh_status.wPortStatus &= ~(USB_PORT_STAT_CONNECTION | USB_PORT_STAT_ENABLE);
+		rh_status.wPortChange |= USB_PORT_STAT_C_CONNECTION;
+		sl811_write(SL811_INTR, SL811_INTR_INSRMV);
+		return 0;
+	}
+
+	/* Send SOF to address 0, endpoint 0. */
+	sl811_write(SL811_LEN_B, 0);
+	sl811_write(SL811_PIDEP_B, PIDEP(USB_PID_SOF, 0));
+	sl811_write(SL811_DEV_B, 0x00);
+	sl811_write(SL811_SOFLOW, SL811_12M_LOW);
+
+	if (status & SL811_INTR_SPEED_FULL) {
+		/* full speed device connect directly to root hub */
+		PDEBUG (0, "Full speed Device attached\n");
+
+		sl811_write(SL811_CTRL1, SL811_CTRL1_RESET);
+		mdelay(20);
+		sl811_write(SL811_CTRL2, SL811_CTL2_HOST | SL811_12M_HI);
+		sl811_write(SL811_CTRL1, SL811_CTRL1_SOF);
+
+		/* start the SOF or EOP */
+		sl811_write(SL811_CTRL_B, SL811_USB_CTRL_ARM);
+		rh_status.wPortStatus |= USB_PORT_STAT_CONNECTION;
+		rh_status.wPortStatus &= ~USB_PORT_STAT_LOW_SPEED;
+		mdelay(2);
+		sl811_write(SL811_INTRSTS, 0xff);
+	} else {
+		/* slow speed device connect directly to root-hub */
+		PDEBUG(0, "Low speed Device attached\n");
+
+		sl811_write(SL811_CTRL1, SL811_CTRL1_RESET);
+		mdelay(20);
+		sl811_write(SL811_CTRL2, SL811_CTL2_HOST | SL811_CTL2_DSWAP | SL811_12M_HI);
+		sl811_write(SL811_CTRL1, SL811_CTRL1_SPEED_LOW | SL811_CTRL1_SOF);
+
+		/* start the SOF or EOP */
+		sl811_write(SL811_CTRL_B, SL811_USB_CTRL_ARM);
+		rh_status.wPortStatus |= USB_PORT_STAT_CONNECTION | USB_PORT_STAT_LOW_SPEED;
+		mdelay(2);
+		sl811_write(SL811_INTRSTS, 0xff);
+	}
+
+	rh_status.wPortChange |= USB_PORT_STAT_C_CONNECTION;
+	sl811_write(SL811_INTR, /*SL811_INTR_INSRMV*/SL811_INTR_DONE_A);
+
+	return 1;
+}
+
+int usb_lowlevel_init(void)
+{
+	root_hub_devnum = 0;
+	sl811_hc_reset();
+	return 0;
+}
+
+int usb_lowlevel_stop(void)
+{
+	sl811_hc_reset();
+	return 0;
+}
+
+int sl811_send_packet(int dir_to_host, int data1, __u8 *buffer, int len)
+{
+	__u8 ctrl = SL811_USB_CTRL_ARM | SL811_USB_CTRL_ENABLE;
+	__u16 status;
+	int err = 0;
+
+	if (len > 239)
+		return -1;
+
+	if (!dir_to_host)
+		ctrl |= SL811_USB_CTRL_DIR_OUT;
+	if (data1)
+		ctrl |= SL811_USB_CTRL_TOGGLE_1;
+
+	sl811_write(SL811_ADDR_A, 0x10);
+	sl811_write(SL811_LEN_A, len);
+	if (!dir_to_host && len)
+		sl811_write_buf(0x10, buffer, len);
+
+	while (err < 3) {
+		if (sl811_read(SL811_SOFCNTDIV)*64 < len * 8 * 2)
+			ctrl |= SL811_USB_CTRL_SOF;
+		else
+			ctrl &= ~SL811_USB_CTRL_SOF;
+		sl811_write(SL811_CTRL_A, ctrl);
+		while (!(sl811_read(SL811_INTRSTS) & SL811_INTR_DONE_A))
+			; /* do nothing */
+
+		sl811_write(SL811_INTRSTS, 0xff);
+		status = sl811_read(SL811_STS_A);
+
+		if (status & SL811_USB_STS_ACK) {
+			int remainder = sl811_read(SL811_CNT_A);
+			if (remainder) {
+				PDEBUG(0, "usb transfer remainder = %d\n", remainder);
+				len -= remainder;
+			}
+			if (dir_to_host && len)
+				sl811_read_buf(0x10, buffer, len);
+			return len;
+		}
+
+		if ((status & SL811_USB_STS_NAK) == SL811_USB_STS_NAK)
+			continue;
+
+		PDEBUG(0, "usb transfer error %#x\n", (int)status);
+		err++;
+	}
+
+	return -1;
+}
+
+int submit_bulk_msg(struct usb_device *dev, unsigned long pipe, void *buffer,
+		    int len)
+{
+	int dir_out = usb_pipeout(pipe);
+	int ep = usb_pipeendpoint(pipe);
+	__u8* buf = (__u8*)buffer;
+	int max = usb_maxpacket(dev, pipe);
+	int done = 0;
+
+	PDEBUG(7, "dev = %ld pipe = %ld buf = %p size = %d dir_out = %d\n",
+	       usb_pipedevice(pipe), usb_pipeendpoint(pipe), buffer, len, dir_out);
+
+	dev->status = 0;
+
+	sl811_write(SL811_DEV_A, usb_pipedevice(pipe));
+	sl811_write(SL811_PIDEP_A, PIDEP(!dir_out ? USB_PID_IN : USB_PID_OUT, ep));
+	while (done < len) {
+		int res = sl811_send_packet(!dir_out, usb_gettoggle(dev, ep, dir_out),
+					    buf+done,
+					    max > len - done ? len - done : max);
+		if (res < 0) {
+			dev->status = res;
+			return res;
+		}
+
+		if (!dir_out && res < max) /* short packet */
+			break;
+
+		done += res;
+		usb_dotoggle(dev, ep, dir_out);
+	}
+
+	dev->act_len = done;
+
+	return 0;
+}
+
+int submit_control_msg(struct usb_device *dev, unsigned long pipe, void *buffer,
+		       int len,struct devrequest *setup)
+{
+	int done = 0;
+	int devnum = usb_pipedevice(pipe);
+
+	dev->status = 0;
+
+	if (devnum == root_hub_devnum)
+		return sl811_rh_submit_urb(dev, pipe, buffer, len, setup);
+
+	PDEBUG(7, "dev = %d pipe = %ld buf = %p size = %d rt = %#x req = %#x\n",
+	       devnum, usb_pipeendpoint(pipe), buffer, len, (int)setup->requesttype,
+	       (int)setup->request);
+
+	sl811_write(SL811_DEV_A, devnum);
+	sl811_write(SL811_PIDEP_A, PIDEP(USB_PID_SETUP, 0));
+	/* setup phase */
+	if (sl811_send_packet(0, 0, (__u8*)setup, sizeof(*setup)) == sizeof(*setup)) {
+		int dir_in = setup->requesttype & USB_DIR_IN;
+		__u8* buf = (__u8*)buffer;
+		int data1 = 1;
+		int max = usb_maxpacket(dev, pipe);
+
+		/* data phase */
+		sl811_write(SL811_PIDEP_A,
+			    PIDEP(dir_in ? USB_PID_IN : USB_PID_OUT, 0));
+		while (done < len) {
+			int res = sl811_send_packet(dir_in, data1, buf+done,
+						    max > len - done ? len - done : max);
+			if (res < 0)
+				return res;
+			done += res;
+
+			if (dir_in && res < max) /* short packet */
+				break;
+
+			data1 = !data1;
+		}
+
+		/* status phase */
+		sl811_write(SL811_PIDEP_A,
+			    PIDEP(!dir_in ? USB_PID_IN : USB_PID_OUT, 0));
+		if (sl811_send_packet(!dir_in, 1, 0, 0) < 0) {
+			PDEBUG(0, "status phase failed!\n");
+			dev->status = -1;
+		}
+	} else {
+		PDEBUG(0, "setup phase failed!\n");
+		dev->status = -1;
+	}
+
+	dev->act_len = done;
+
+	return done;
+}
+
+int submit_int_msg(struct usb_device *dev, unsigned long pipe, void *buffer,
+		   int len, int interval)
+{
+	PDEBUG(7, "dev = %p pipe = %#lx buf = %p size = %d int = %d\n", dev, pipe,
+	       buffer, len, interval);
+	return -1;
+}
+
+/*
+ * SL811 Virtual Root Hub
+ */
+
+/* Device descriptor */
+static __u8 sl811_rh_dev_des[] =
+{
+	0x12,	    /*	__u8  bLength; */
+	0x01,	    /*	__u8  bDescriptorType; Device */
+	0x10,	    /*	__u16 bcdUSB; v1.1 */
+	0x01,
+	0x09,	    /*	__u8  bDeviceClass; HUB_CLASSCODE */
+	0x00,	    /*	__u8  bDeviceSubClass; */
+	0x00,	    /*	__u8  bDeviceProtocol; */
+	0x08,	    /*	__u8  bMaxPacketSize0; 8 Bytes */
+	0x00,	    /*	__u16 idVendor; */
+	0x00,
+	0x00,	    /*	__u16 idProduct; */
+	0x00,
+	0x00,	    /*	__u16 bcdDevice; */
+	0x00,
+	0x00,	    /*	__u8  iManufacturer; */
+	0x02,	    /*	__u8  iProduct; */
+	0x01,	    /*	__u8  iSerialNumber; */
+	0x01	    /*	__u8  bNumConfigurations; */
+};
+
+/* Configuration descriptor */
+static __u8 sl811_rh_config_des[] =
+{
+	0x09,	    /*	__u8  bLength; */
+	0x02,	    /*	__u8  bDescriptorType; Configuration */
+	0x19,	    /*	__u16 wTotalLength; */
+	0x00,
+	0x01,	    /*	__u8  bNumInterfaces; */
+	0x01,	    /*	__u8  bConfigurationValue; */
+	0x00,	    /*	__u8  iConfiguration; */
+	0x40,	    /*	__u8  bmAttributes;
+		    Bit 7: Bus-powered, 6: Self-powered, 5 Remote-wakwup,
+		    4..0: resvd */
+	0x00,	    /*	__u8  MaxPower; */
+
+	/* interface */
+	0x09,	    /*	__u8  if_bLength; */
+	0x04,	    /*	__u8  if_bDescriptorType; Interface */
+	0x00,	    /*	__u8  if_bInterfaceNumber; */
+	0x00,	    /*	__u8  if_bAlternateSetting; */
+	0x01,	    /*	__u8  if_bNumEndpoints; */
+	0x09,	    /*	__u8  if_bInterfaceClass; HUB_CLASSCODE */
+	0x00,	    /*	__u8  if_bInterfaceSubClass; */
+	0x00,	    /*	__u8  if_bInterfaceProtocol; */
+	0x00,	    /*	__u8  if_iInterface; */
+
+	/* endpoint */
+	0x07,	    /*	__u8  ep_bLength; */
+	0x05,	    /*	__u8  ep_bDescriptorType; Endpoint */
+	0x81,	    /*	__u8  ep_bEndpointAddress; IN Endpoint 1 */
+	0x03,	    /*	__u8  ep_bmAttributes; Interrupt */
+	0x08,	    /*	__u16 ep_wMaxPacketSize; */
+	0x00,
+	0xff	    /*	__u8  ep_bInterval; 255 ms */
+};
+
+/* root hub class descriptor*/
+static __u8 sl811_rh_hub_des[] =
+{
+	0x09,			/*  __u8  bLength; */
+	0x29,			/*  __u8  bDescriptorType; Hub-descriptor */
+	0x01,			/*  __u8  bNbrPorts; */
+	0x00,			/* __u16  wHubCharacteristics; */
+	0x00,
+	0x50,			/*  __u8  bPwrOn2pwrGood; 2ms */
+	0x00,			/*  __u8  bHubContrCurrent; 0 mA */
+	0xfc,			/*  __u8  DeviceRemovable; *** 7 Ports max *** */
+	0xff			/*  __u8  PortPwrCtrlMask; *** 7 ports max *** */
+};
+
+/*
+ * helper routine for returning string descriptors in UTF-16LE
+ * input can actually be ISO-8859-1; ASCII is its 7-bit subset
+ */
+static int ascii2utf (char *s, u8 *utf, int utfmax)
+{
+	int retval;
+
+	for (retval = 0; *s && utfmax > 1; utfmax -= 2, retval += 2) {
+		*utf++ = *s++;
+		*utf++ = 0;
+	}
+	return retval;
+}
+
+/*
+ * root_hub_string is used by each host controller's root hub code,
+ * so that they're identified consistently throughout the system.
+ */
+int usb_root_hub_string (int id, int serial, char *type, __u8 *data, int len)
+{
+	char buf [30];
+
+	/* assert (len > (2 * (sizeof (buf) + 1)));
+	   assert (strlen (type) <= 8);*/
+
+	/* language ids */
+	if (id == 0) {
+		*data++ = 4; *data++ = 3;	/* 4 bytes data */
+		*data++ = 0; *data++ = 0;	/* some language id */
+		return 4;
+
+	/* serial number */
+	} else if (id == 1) {
+		sprintf (buf, "%x", serial);
+
+	/* product description */
+	} else if (id == 2) {
+		sprintf (buf, "USB %s Root Hub", type);
+
+	/* id 3 == vendor description */
+
+	/* unsupported IDs --> "stall" */
+	} else
+	    return 0;
+
+	data [0] = 2 + ascii2utf (buf, data + 2, len - 2);
+	data [1] = 3;
+	return data [0];
+}
+
+/* helper macro */
+#define OK(x)	len = (x); break
+
+/*
+ * This function handles all USB request to the the virtual root hub
+ */
+static int sl811_rh_submit_urb(struct usb_device *usb_dev, unsigned long pipe,
+			       void *data, int buf_len, struct devrequest *cmd)
+{
+	__u8 data_buf[16];
+	__u8 *bufp = data_buf;
+	int len = 0;
+	int status = 0;
+
+	__u16 bmRType_bReq;
+	__u16 wValue;
+	__u16 wIndex;
+	__u16 wLength;
+
+	if (usb_pipeint(pipe)) {
+		PDEBUG(0, "interrupt transfer unimplemented!\n");
+		return 0;
+	}
+
+	bmRType_bReq  = cmd->requesttype | (cmd->request << 8);
+	wValue	      = le16_to_cpu (cmd->value);
+	wIndex	      = le16_to_cpu (cmd->index);
+	wLength	      = le16_to_cpu (cmd->length);
+
+	PDEBUG(5, "submit rh urb, req = %d(%x) val = %#x index = %#x len=%d\n",
+	       bmRType_bReq, bmRType_bReq, wValue, wIndex, wLength);
+
+	/* Request Destination:
+		   without flags: Device,
+		   USB_RECIP_INTERFACE: interface,
+		   USB_RECIP_ENDPOINT: endpoint,
+		   USB_TYPE_CLASS means HUB here,
+		   USB_RECIP_OTHER | USB_TYPE_CLASS  almost ever means HUB_PORT here
+	*/
+	switch (bmRType_bReq) {
+	case RH_GET_STATUS:
+		*(__u16 *)bufp = cpu_to_le16(1);
+		OK(2);
+
+	case RH_GET_STATUS | USB_RECIP_INTERFACE:
+		*(__u16 *)bufp = cpu_to_le16(0);
+		OK(2);
+
+	case RH_GET_STATUS | USB_RECIP_ENDPOINT:
+		*(__u16 *)bufp = cpu_to_le16(0);
+		OK(2);
+
+	case RH_GET_STATUS | USB_TYPE_CLASS:
+		*(__u32 *)bufp = cpu_to_le32(0);
+		OK(4);
+
+	case RH_GET_STATUS | USB_RECIP_OTHER | USB_TYPE_CLASS:
+		*(__u32 *)bufp = cpu_to_le32(rh_status.wPortChange<<16 | rh_status.wPortStatus);
+		OK(4);
+
+	case RH_CLEAR_FEATURE | USB_RECIP_ENDPOINT:
+		switch (wValue) {
+		case 1:
+			OK(0);
+		}
+		break;
+
+	case RH_CLEAR_FEATURE | USB_TYPE_CLASS:
+		switch (wValue) {
+		case C_HUB_LOCAL_POWER:
+			OK(0);
+
+		case C_HUB_OVER_CURRENT:
+			OK(0);
+		}
+		break;
+
+	case RH_CLEAR_FEATURE | USB_RECIP_OTHER | USB_TYPE_CLASS:
+		switch (wValue) {
+		case USB_PORT_FEAT_ENABLE:
+			rh_status.wPortStatus &= ~USB_PORT_STAT_ENABLE;
+			OK(0);
+
+		case USB_PORT_FEAT_SUSPEND:
+			rh_status.wPortStatus &= ~USB_PORT_STAT_SUSPEND;
+			OK(0);
+
+		case USB_PORT_FEAT_POWER:
+			rh_status.wPortStatus &= ~USB_PORT_STAT_POWER;
+			OK(0);
+
+		case USB_PORT_FEAT_C_CONNECTION:
+			rh_status.wPortChange &= ~USB_PORT_STAT_C_CONNECTION;
+			OK(0);
+
+		case USB_PORT_FEAT_C_ENABLE:
+			rh_status.wPortChange &= ~USB_PORT_STAT_C_ENABLE;
+			OK(0);
+
+		case USB_PORT_FEAT_C_SUSPEND:
+			rh_status.wPortChange &= ~USB_PORT_STAT_C_SUSPEND;
+			OK(0);
+
+		case USB_PORT_FEAT_C_OVER_CURRENT:
+			rh_status.wPortChange &= ~USB_PORT_STAT_C_OVERCURRENT;
+			OK(0);
+
+		case USB_PORT_FEAT_C_RESET:
+			rh_status.wPortChange &= ~USB_PORT_STAT_C_RESET;
+			OK(0);
+		}
+		break;
+
+	case RH_SET_FEATURE | USB_RECIP_OTHER | USB_TYPE_CLASS:
+		switch (wValue) {
+		case USB_PORT_FEAT_SUSPEND:
+			rh_status.wPortStatus |= USB_PORT_STAT_SUSPEND;
+			OK(0);
+
+		case USB_PORT_FEAT_RESET:
+			rh_status.wPortStatus |= USB_PORT_STAT_RESET;
+			rh_status.wPortChange = 0;
+			rh_status.wPortChange |= USB_PORT_STAT_C_RESET;
+			rh_status.wPortStatus &= ~USB_PORT_STAT_RESET;
+			rh_status.wPortStatus |= USB_PORT_STAT_ENABLE;
+			OK(0);
+
+		case USB_PORT_FEAT_POWER:
+			rh_status.wPortStatus |= USB_PORT_STAT_POWER;
+			OK(0);
+
+		case USB_PORT_FEAT_ENABLE:
+			rh_status.wPortStatus |= USB_PORT_STAT_ENABLE;
+			OK(0);
+		}
+		break;
+
+	case RH_SET_ADDRESS:
+		root_hub_devnum = wValue;
+		OK(0);
+
+	case RH_GET_DESCRIPTOR:
+		switch ((wValue & 0xff00) >> 8) {
+		case USB_DT_DEVICE:
+			len = sizeof(sl811_rh_dev_des);
+			bufp = sl811_rh_dev_des;
+			OK(len);
+
+		case USB_DT_CONFIG:
+			len = sizeof(sl811_rh_config_des);
+			bufp = sl811_rh_config_des;
+			OK(len);
+
+		case USB_DT_STRING:
+			len = usb_root_hub_string(wValue & 0xff, (int)(long)0,	"SL811HS", data, wLength);
+			if (len > 0) {
+				bufp = data;
+				OK(len);
+			}
+
+		default:
+			status = -32;
+		}
+		break;
+
+	case RH_GET_DESCRIPTOR | USB_TYPE_CLASS:
+		len = sizeof(sl811_rh_hub_des);
+		bufp = sl811_rh_hub_des;
+		OK(len);
+
+	case RH_GET_CONFIGURATION:
+		bufp[0] = 0x01;
+		OK(1);
+
+	case RH_SET_CONFIGURATION:
+		OK(0);
+
+	default:
+		PDEBUG(1, "unsupported root hub command\n");
+		status = -32;
+	}
+
+	len = min(len, buf_len);
+	if (data != bufp)
+		memcpy(data, bufp, len);
+
+	PDEBUG(5, "len = %d, status = %d\n", len, status);
+
+	usb_dev->status = status;
+	usb_dev->act_len = len;
+
+	return status == 0 ? len : status;
+}
+
+#endif	/* CONFIG_USB_SL811HS */

examples/Makefile

@@ -45,6 +45,10 @@ ifeq ($(ARCH),m68k)
 LOAD_ADDR = 0x20000  -L $(clibdir)
 endif
 
+ifeq ($(ARCH),microblaze)
+LOAD_ADDR = 0x80F00000
+endif
+
 include $(TOPDIR)/config.mk
 
 SREC	= hello_world.srec

examples/stubs.c

@@ -94,6 +94,18 @@ gd_t *global_data;
 "	move.l	(%%a0), %%a0\n"		\
 "	jmp	(%%a0)\n"			\
 	: : "i"(offsetof(gd_t, jt)), "i"(XF_ ## x * sizeof(void *)) : "a0");
+#elif defined(CONFIG_MICROBLZE)
+/*
+ * r31 holds the pointer to the global_data. r5 is a call-clobbered.
+ */
+#define EXPORT_FUNC(x)				\
+	asm volatile (				\
+"	.globl " #x "\n"			\
+#x ":\n"					\
+"	lwi	r5, r31, %0\n"			\
+"	lwi	r5, r5, %1\n"			\
+"	bra	r5\n"				\
+	: : "i"(offsetof(gd_t, jt)), "i"(XF_ ## x * sizeof(void *)) : "r5");
 #else
 #error stubs definition missing for this architecture
 #endif

fs/jffs2/jffs2_1pass.c

@@ -182,8 +182,8 @@ static int read_nand_cached(u32 off, u32 size, u_char *buf)
 			if (!nand_cache) {
 				/* This memory never gets freed but 'cause
 				   it's a bootloader, nobody cares */
-				nand_cache = malloc(NAND_CACHE_SIZE); 
-				if (!nand_cache) { 
+				nand_cache = malloc(NAND_CACHE_SIZE);
+				if (!nand_cache) {
 					printf("read_nand_cached: can't alloc cache size %d bytes\n",
 					       NAND_CACHE_SIZE);
 					return -1;
@@ -241,7 +241,7 @@ static void *get_node_mem(u32 off)
 	return ret;
 }
 
-static void put_fl_mem(void *buf) 
+static void put_fl_mem(void *buf)
 {
 	free(buf);
 }
@@ -258,7 +258,7 @@ static inline void *get_node_mem(u32 off)
 	return (void*)off;
 }
 
-static inline void put_fl_mem(void *buf) 
+static inline void put_fl_mem(void *buf)
 {
 }
 
@@ -414,7 +414,7 @@ static int compare_dirents(struct b_node *new, struct b_node *old)
 	struct jffs2_raw_dirent ojOld;
 	struct jffs2_raw_dirent *jNew =
 		(struct jffs2_raw_dirent *)get_fl_mem(new->offset, sizeof(ojNew), &ojNew);
-	struct jffs2_raw_dirent *jOld = 
+	struct jffs2_raw_dirent *jOld =
 		(struct jffs2_raw_dirent *)get_fl_mem(old->offset, sizeof(ojOld), &ojOld);
 	int cmp;
 
@@ -511,7 +511,7 @@ jffs2_1pass_read_inode(struct b_lists *pL, u32 inode, char *dest)
 	 * we will live with it.
 	 */
 	for (b = pL->frag.listHead; b != NULL; b = b->next) {
-		jNode = (struct jffs2_raw_inode *) get_fl_mem(b->offset, 
+		jNode = (struct jffs2_raw_inode *) get_fl_mem(b->offset,
 		        sizeof(struct jffs2_raw_inode), NULL);
 		if ((inode == jNode->ino)) {
 			/* get actual file length from the newest node */

include/asm-microblaze/arch-microblaze/xbasic_types.h

@@ -0,0 +1,301 @@
+/******************************************************************************
+*
+*     Author: Xilinx, Inc.
+*
+*
+*     This program is free software; you can redistribute it and/or modify it
+*     under the terms of the GNU General Public License as published by the
+*     Free Software Foundation; either version 2 of the License, or (at your
+*     option) any later version.
+*
+*
+*     XILINX IS PROVIDING THIS DESIGN, CODE, OR INFORMATION "AS IS" AS A
+*     COURTESY TO YOU. BY PROVIDING THIS DESIGN, CODE, OR INFORMATION AS
+*     ONE POSSIBLE IMPLEMENTATION OF THIS FEATURE, APPLICATION OR STANDARD,
+*     XILINX IS MAKING NO REPRESENTATION THAT THIS IMPLEMENTATION IS FREE
+*     FROM ANY CLAIMS OF INFRINGEMENT, AND YOU ARE RESPONSIBLE FOR OBTAINING
+*     ANY THIRD PARTY RIGHTS YOU MAY REQUIRE FOR YOUR IMPLEMENTATION.
+*     XILINX EXPRESSLY DISCLAIMS ANY WARRANTY WHATSOEVER WITH RESPECT TO
+*     THE ADEQUACY OF THE IMPLEMENTATION, INCLUDING BUT NOT LIMITED TO ANY
+*     WARRANTIES OR REPRESENTATIONS THAT THIS IMPLEMENTATION IS FREE FROM
+*     CLAIMS OF INFRINGEMENT, IMPLIED WARRANTIES OF MERCHANTABILITY AND
+*     FITNESS FOR A PARTICULAR PURPOSE.
+*
+*
+*     Xilinx hardware products are not intended for use in life support
+*     appliances, devices, or systems. Use in such applications is
+*     expressly prohibited.
+*
+*
+*     (c) Copyright 2002-2003 Xilinx Inc.
+*     All rights reserved.
+*
+*
+*     You should have received a copy of the GNU General Public License along
+*     with this program; if not, write to the Free Software Foundation, Inc.,
+*     675 Mass Ave, Cambridge, MA 02139, USA.
+*
+******************************************************************************/
+/*****************************************************************************/
+/**
+*
+* @file xbasic_types.h
+*
+* This file contains basic types for Xilinx software IP.  These types do not
+* follow the standard naming convention with respect to using the component
+* name in front of each name because they are considered to be primitives.
+*
+* @note
+*
+* This file contains items which are architecture dependent.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver	 Who	Date	Changes
+* ----- ---- -------- -----------------------------------------------
+* 1.00a rmm  12/14/01 First release
+*	rmm  05/09/03 Added "xassert always" macros to rid ourselves of diab
+*		      compiler warnings
+* </pre>
+*
+******************************************************************************/
+
+#ifndef XBASIC_TYPES_H		/* prevent circular inclusions */
+#define XBASIC_TYPES_H		/* by using protection macros */
+
+/***************************** Include Files *********************************/
+
+/************************** Constant Definitions *****************************/
+
+#ifndef TRUE
+#define TRUE 1
+#endif
+#ifndef FALSE
+#define FALSE 0
+#endif
+
+#ifndef NULL
+#define NULL 0
+#endif
+/** Null */
+
+#define XCOMPONENT_IS_READY	0x11111111	/* component has been initialized */
+#define XCOMPONENT_IS_STARTED	0x22222222	/* component has been started */
+
+/* the following constants and declarations are for unit test purposes and are
+ * designed to be used in test applications.
+ */
+#define XTEST_PASSED	0
+#define XTEST_FAILED	1
+
+#define XASSERT_NONE	 0
+#define XASSERT_OCCURRED 1
+
+extern unsigned int XAssertStatus;
+extern void XAssert(char *, int);
+
+/**************************** Type Definitions *******************************/
+
+/** @name Primitive types
+ * These primitive types are created for transportability.
+ * They are dependent upon the target architecture.
+ * @{
+ */
+#include <linux/types.h>
+
+typedef struct {
+	u32 Upper;
+	u32 Lower;
+} Xuint64;
+
+/* Xilinx's unsigned integer types */
+typedef u32 Xuint32;
+typedef u16 Xuint16;
+typedef u8 Xuint8;
+
+/* and signed integer types */
+typedef s32 Xint32;
+typedef s16 Xint16;
+typedef s8 Xint8;
+
+#ifndef NULL
+#define NULL 0
+#endif
+
+typedef unsigned long Xboolean;
+#define XNULL	NULL
+
+#define XTRUE	1
+#define XFALSE	0
+
+/*@}*/
+
+/**
+ * This data type defines an interrupt handler for a device.
+ * The argument points to the instance of the component
+ */
+typedef void (*XInterruptHandler) (void *InstancePtr);
+
+/**
+ * This data type defines a callback to be invoked when an
+ * assert occurs. The callback is invoked only when asserts are enabled
+ */
+typedef void (*XAssertCallback) (char *FilenamePtr, int LineNumber);
+
+/***************** Macros (Inline Functions) Definitions *********************/
+
+/*****************************************************************************/
+/**
+* Return the most significant half of the 64 bit data type.
+*
+* @param x is the 64 bit word.
+*
+* @return
+*
+* The upper 32 bits of the 64 bit word.
+*
+* @note
+*
+* None.
+*
+******************************************************************************/
+#define XUINT64_MSW(x) ((x).Upper)
+
+/*****************************************************************************/
+/**
+* Return the least significant half of the 64 bit data type.
+*
+* @param x is the 64 bit word.
+*
+* @return
+*
+* The lower 32 bits of the 64 bit word.
+*
+* @note
+*
+* None.
+*
+******************************************************************************/
+#define XUINT64_LSW(x) ((x).Lower)
+
+#ifndef NDEBUG
+
+/*****************************************************************************/
+/**
+* This assert macro is to be used for functions that do not return anything
+* (void). This in conjunction with the XWaitInAssert boolean can be used to
+* accomodate tests so that asserts which fail allow execution to continue.
+*
+* @param expression is the expression to evaluate. If it evaluates to false,
+*	 the assert occurs.
+*
+* @return
+*
+* Returns void unless the XWaitInAssert variable is true, in which case
+* no return is made and an infinite loop is entered.
+*
+* @note
+*
+* None.
+*
+******************************************************************************/
+#define XASSERT_VOID(expression)			\
+{							\
+	if (expression) {				\
+		XAssertStatus = XASSERT_NONE;		\
+	} else {					\
+		XAssert(__FILE__, __LINE__);		\
+		XAssertStatus = XASSERT_OCCURRED;	\
+		return;					\
+	}						\
+}
+
+/*****************************************************************************/
+/**
+* This assert macro is to be used for functions that do return a value. This in
+* conjunction with the XWaitInAssert boolean can be used to accomodate tests so
+* that asserts which fail allow execution to continue.
+*
+* @param expression is the expression to evaluate. If it evaluates to false,
+*	 the assert occurs.
+*
+* @return
+*
+* Returns 0 unless the XWaitInAssert variable is true, in which case
+* no return is made and an infinite loop is entered.
+*
+* @note
+*
+* None.
+*
+******************************************************************************/
+#define XASSERT_NONVOID(expression)			\
+{							\
+	if (expression) {				\
+		XAssertStatus = XASSERT_NONE;		\
+	} else {					\
+		XAssert(__FILE__, __LINE__);		\
+		XAssertStatus = XASSERT_OCCURRED;	\
+		return 0;				\
+	}						\
+}
+
+/*****************************************************************************/
+/**
+* Always assert. This assert macro is to be used for functions that do not
+* return anything (void). Use for instances where an assert should always
+* occur.
+*
+* @return
+*
+* Returns void unless the XWaitInAssert variable is true, in which case
+* no return is made and an infinite loop is entered.
+*
+* @note
+*
+* None.
+*
+******************************************************************************/
+#define XASSERT_VOID_ALWAYS()				\
+{							\
+	XAssert(__FILE__, __LINE__);			\
+	XAssertStatus = XASSERT_OCCURRED;		\
+	return;						\
+}
+
+/*****************************************************************************/
+/**
+* Always assert. This assert macro is to be used for functions that do return
+* a value. Use for instances where an assert should always occur.
+*
+* @return
+*
+* Returns void unless the XWaitInAssert variable is true, in which case
+* no return is made and an infinite loop is entered.
+*
+* @note
+*
+* None.
+*
+******************************************************************************/
+#define XASSERT_NONVOID_ALWAYS()			\
+{							\
+	XAssert(__FILE__, __LINE__);			\
+	XAssertStatus = XASSERT_OCCURRED;		\
+	return 0;					\
+}
+
+#else
+
+#define XASSERT_VOID(expression)
+#define XASSERT_VOID_ALWAYS()
+#define XASSERT_NONVOID(expression)
+#define XASSERT_NONVOID_ALWAYS()
+#endif
+
+/************************** Function Prototypes ******************************/
+
+void XAssertSetCallback(XAssertCallback Routine);
+
+#endif	/* end of protection macro */

include/asm-microblaze/arch-microblaze/xio.h

@@ -0,0 +1,63 @@
+/*
+ * xio.h
+ *
+ * Defines XIo functions for Xilinx OCP in terms of Linux primitives
+ *
+ * Author: MontaVista Software, Inc.
+ *         source@mvista.com
+ *
+ * 2002 (c) MontaVista, Software, Inc.  This file is licensed under the terms
+ * of the GNU General Public License version 2.  This program is licensed
+ * "as is" without any warranty of any kind, whether express or implied.
+ */
+
+#ifndef XIO_H
+#define XIO_H
+
+#include "xbasic_types.h"
+#include <asm/io.h>
+
+typedef u32 XIo_Address;
+
+extern inline u8
+XIo_In8(XIo_Address InAddress)
+{
+	return (u8) in_8((volatile unsigned char *) InAddress);
+}
+extern inline u16
+XIo_In16(XIo_Address InAddress)
+{
+	return (u16) in_be16((volatile unsigned short *) InAddress);
+}
+extern inline u32
+XIo_In32(XIo_Address InAddress)
+{
+	return (u32) in_be32((volatile unsigned *) InAddress);
+}
+extern inline void
+XIo_Out8(XIo_Address OutAddress, u8 Value)
+{
+	out_8((volatile unsigned char *) OutAddress, Value);
+}
+extern inline void
+XIo_Out16(XIo_Address OutAddress, u16 Value)
+{
+	out_be16((volatile unsigned short *) OutAddress, Value);
+}
+extern inline void
+XIo_Out32(XIo_Address OutAddress, u32 Value)
+{
+	out_be32((volatile unsigned *) OutAddress, Value);
+}
+
+#define XIo_ToLittleEndian16(s,d) (*(u16*)(d) = cpu_to_le16((u16)(s)))
+#define XIo_ToLittleEndian32(s,d) (*(u32*)(d) = cpu_to_le32((u32)(s)))
+#define XIo_ToBigEndian16(s,d) (*(u16*)(d) = cpu_to_be16((u16)(s)))
+#define XIo_ToBigEndian32(s,d) (*(u32*)(d) = cpu_to_be32((u32)(s)))
+
+#define XIo_FromLittleEndian16(s,d) (*(u16*)(d) = le16_to_cpu((u16)(s)))
+#define XIo_FromLittleEndian32(s,d) (*(u32*)(d) = le32_to_cpu((u32)(s)))
+#define XIo_FromBigEndian16(s,d) (*(u16*)(d) = be16_to_cpu((u16)(s)))
+#define XIo_FromBigEndian32(s,d) (*(u32*)(d) = be32_to_cpu((u32)(s)))
+
+#endif				/* XIO_H */

include/asm-microblaze/arch-microblaze/xuartlite_l.h

@@ -0,0 +1,256 @@
+/*****************************************************************************
+*
+*	XILINX IS PROVIDING THIS DESIGN, CODE, OR INFORMATION "AS IS"
+*	AS A COURTESY TO YOU, SOLELY FOR USE IN DEVELOPING PROGRAMS AND
+*	SOLUTIONS FOR XILINX DEVICES.  BY PROVIDING THIS DESIGN, CODE,
+*	OR INFORMATION AS ONE POSSIBLE IMPLEMENTATION OF THIS FEATURE,
+*	APPLICATION OR STANDARD, XILINX IS MAKING NO REPRESENTATION
+*	THAT THIS IMPLEMENTATION IS FREE FROM ANY CLAIMS OF INFRINGEMENT,
+*	AND YOU ARE RESPONSIBLE FOR OBTAINING ANY RIGHTS YOU MAY REQUIRE
+*	FOR YOUR IMPLEMENTATION.  XILINX EXPRESSLY DISCLAIMS ANY
+*	WARRANTY WHATSOEVER WITH RESPECT TO THE ADEQUACY OF THE
+*	IMPLEMENTATION, INCLUDING BUT NOT LIMITED TO ANY WARRANTIES OR
+*	REPRESENTATIONS THAT THIS IMPLEMENTATION IS FREE FROM CLAIMS OF
+*	INFRINGEMENT, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+*	FOR A PARTICULAR PURPOSE.
+*
+*	(c) Copyright 2002 Xilinx Inc.
+*	All rights reserved.
+*
+*****************************************************************************/
+/****************************************************************************/
+/**
+*
+* @file xuartlite_l.h
+*
+* This header file contains identifiers and low-level driver functions (or
+* macros) that can be used to access the device.  High-level driver functions
+* are defined in xuartlite.h.
+*
+* <pre>
+* MODIFICATION HISTORY:
+*
+* Ver	Who  Date     Changes
+* ----- ---- -------- -----------------------------------------------
+* 1.00b rpm  04/25/02 First release
+* </pre>
+*
+*****************************************************************************/
+
+#ifndef XUARTLITE_L_H /* prevent circular inclusions */
+#define XUARTLITE_L_H /* by using protection macros */
+
+/***************************** Include Files ********************************/
+
+#include "xbasic_types.h"
+#include "xio.h"
+
+/************************** Constant Definitions ****************************/
+
+/* UART Lite register offsets */
+
+#define XUL_RX_FIFO_OFFSET		0   /* receive FIFO, read only */
+#define XUL_TX_FIFO_OFFSET		4   /* transmit FIFO, write only */
+#define XUL_STATUS_REG_OFFSET		8   /* status register, read only */
+#define XUL_CONTROL_REG_OFFSET		12  /* control register, write only */
+
+/* control register bit positions */
+
+#define XUL_CR_ENABLE_INTR		0x10	/* enable interrupt */
+#define XUL_CR_FIFO_RX_RESET		0x02	/* reset receive FIFO */
+#define XUL_CR_FIFO_TX_RESET		0x01	/* reset transmit FIFO */
+
+/* status register bit positions */
+
+#define XUL_SR_PARITY_ERROR		0x80
+#define XUL_SR_FRAMING_ERROR		0x40
+#define XUL_SR_OVERRUN_ERROR		0x20
+#define XUL_SR_INTR_ENABLED		0x10	/* interrupt enabled */
+#define XUL_SR_TX_FIFO_FULL		0x08	/* transmit FIFO full */
+#define XUL_SR_TX_FIFO_EMPTY		0x04	/* transmit FIFO empty */
+#define XUL_SR_RX_FIFO_FULL		0x02	/* receive FIFO full */
+#define XUL_SR_RX_FIFO_VALID_DATA	0x01	/* data in receive FIFO */
+
+/* the following constant specifies the size of the FIFOs, the size of the
+ * FIFOs includes the transmitter and receiver such that it is the total number
+ * of bytes that the UART can buffer
+ */
+#define XUL_FIFO_SIZE		    16
+
+/* Stop bits are fixed at 1. Baud, parity, and data bits are fixed on a
+ * per instance basis
+ */
+#define XUL_STOP_BITS		    1
+
+/* Parity definitions
+ */
+#define XUL_PARITY_NONE		    0
+#define XUL_PARITY_ODD		    1
+#define XUL_PARITY_EVEN		    2
+
+/**************************** Type Definitions ******************************/
+
+/***************** Macros (Inline Functions) Definitions ********************/
+
+/*****************************************************************************
+*
+* Low-level driver macros and functions. The list below provides signatures
+* to help the user use the macros.
+*
+* void XUartLite_mSetControlReg(u32 BaseAddress, u32 Mask)
+* u32 XUartLite_mGetControlReg(u32 BaseAddress)
+* u32 XUartLite_mGetStatusReg(u32 BaseAddress)
+*
+* Xboolean XUartLite_mIsReceiveEmpty(u32 BaseAddress)
+* Xboolean XUartLite_mIsTransmitFull(u32 BaseAddress)
+* Xboolean XUartLite_mIsIntrEnabled(u32 BaseAddress)
+*
+* void XUartLite_mEnableIntr(u32 BaseAddress)
+* void XUartLite_mDisableIntr(u32 BaseAddress)
+*
+* void XUartLite_SendByte(u32 BaseAddress, u8 Data);
+* u8 XUartLite_RecvByte(u32 BaseAddress);
+*
+*****************************************************************************/
+
+/****************************************************************************/
+/**
+*
+* Set the contents of the control register. Use the XUL_CR_* constants defined
+* above to create the bit-mask to be written to the register.
+*
+* @param    BaseAddress is the base address of the device
+* @param    Mask is the 32-bit value to write to the control register
+*
+* @return   None.
+*
+* @note	    None.
+*
+*****************************************************************************/
+#define XUartLite_mSetControlReg(BaseAddress, Mask) \
+		    XIo_Out32((BaseAddress) + XUL_CONTROL_REG_OFFSET, (Mask))
+
+
+/****************************************************************************/
+/**
+*
+* Get the contents of the control register. Use the XUL_CR_* constants defined
+* above to interpret the bit-mask returned.
+*
+* @param    BaseAddress is the	base address of the device
+*
+* @return   A 32-bit value representing the contents of the control register.
+*
+* @note	    None.
+*
+*****************************************************************************/
+#define XUartLite_mGetControlReg(BaseAddress) \
+		    XIo_In32((BaseAddress) + XUL_CONTROL_REG_OFFSET)
+
+
+/****************************************************************************/
+/**
+*
+* Get the contents of the status register. Use the XUL_SR_* constants defined
+* above to interpret the bit-mask returned.
+*
+* @param    BaseAddress is the	base address of the device
+*
+* @return   A 32-bit value representing the contents of the status register.
+*
+* @note	    None.
+*
+*****************************************************************************/
+#define XUartLite_mGetStatusReg(BaseAddress) \
+		    XIo_In32((BaseAddress) + XUL_STATUS_REG_OFFSET)
+
+
+/****************************************************************************/
+/**
+*
+* Check to see if the receiver has data.
+*
+* @param    BaseAddress is the	base address of the device
+*
+* @return   XTRUE if the receiver is empty, XFALSE if there is data present.
+*
+* @note	    None.
+*
+*****************************************************************************/
+#define XUartLite_mIsReceiveEmpty(BaseAddress) \
+	  (!(XUartLite_mGetStatusReg((BaseAddress)) & XUL_SR_RX_FIFO_VALID_DATA))
+
+
+/****************************************************************************/
+/**
+*
+* Check to see if the transmitter is full.
+*
+* @param    BaseAddress is the	base address of the device
+*
+* @return   XTRUE if the transmitter is full, XFALSE otherwise.
+*
+* @note	    None.
+*
+*****************************************************************************/
+#define XUartLite_mIsTransmitFull(BaseAddress) \
+		(XUartLite_mGetStatusReg((BaseAddress)) & XUL_SR_TX_FIFO_FULL)
+
+
+/****************************************************************************/
+/**
+*
+* Check to see if the interrupt is enabled.
+*
+* @param    BaseAddress is the	base address of the device
+*
+* @return   XTRUE if the interrupt is enabled, XFALSE otherwise.
+*
+* @note	    None.
+*
+*****************************************************************************/
+#define XUartLite_mIsIntrEnabled(BaseAddress) \
+		(XUartLite_mGetStatusReg((BaseAddress)) & XUL_SR_INTR_ENABLED)
+
+
+/****************************************************************************/
+/**
+*
+* Enable the device interrupt. Preserve the contents of the control register.
+*
+* @param    BaseAddress is the	base address of the device
+*
+* @return   None.
+*
+* @note	    None.
+*
+*****************************************************************************/
+#define XUartLite_mEnableIntr(BaseAddress) \
+	       XUartLite_mSetControlReg((BaseAddress), \
+		   XUartLite_mGetControlReg((BaseAddress)) | XUL_CR_ENABLE_INTR)
+
+
+/****************************************************************************/
+/**
+*
+* Disable the device interrupt. Preserve the contents of the control register.
+*
+* @param    BaseAddress is the	base address of the device
+*
+* @return   None.
+*
+* @note	    None.
+*
+*****************************************************************************/
+#define XUartLite_mDisableIntr(BaseAddress) \
+	      XUartLite_mSetControlReg((BaseAddress), \
+		  XUartLite_mGetControlReg((BaseAddress)) & ~XUL_CR_ENABLE_INTR)
+
+
+/************************** Function Prototypes *****************************/
+
+void XUartLite_SendByte(u32 BaseAddress, u8 Data);
+u8 XUartLite_RecvByte(u32 BaseAddress);
+
+
+#endif		  /* end of protection macro */

include/asm-microblaze/bitops.h

@@ -0,0 +1,392 @@
+#ifndef _MICROBLAZE_BITOPS_H
+#define _MICROBLAZE_BITOPS_H
+
+/*
+ * Copyright 1992, Linus Torvalds.
+ */
+
+#include <linux/config.h>
+#include <asm/byteorder.h>	/* swab32 */
+#include <asm/system.h>		/* save_flags */
+
+#ifdef __KERNEL__
+/*
+ * Function prototypes to keep gcc -Wall happy
+ */
+
+/*
+ * The __ functions are not atomic
+ */
+
+extern void set_bit(int nr, volatile void * addr);
+extern void __set_bit(int nr, volatile void * addr);
+
+extern void clear_bit(int nr, volatile void * addr);
+#define __clear_bit(nr, addr) clear_bit(nr, addr)
+
+extern void change_bit(int nr, volatile void * addr);
+extern void __change_bit(int nr, volatile void * addr);
+extern int test_and_set_bit(int nr, volatile void * addr);
+extern int __test_and_set_bit(int nr, volatile void * addr);
+extern int test_and_clear_bit(int nr, volatile void * addr);
+extern int __test_and_clear_bit(int nr, volatile void * addr);
+extern int test_and_change_bit(int nr, volatile void * addr);
+extern int __test_and_change_bit(int nr, volatile void * addr);
+extern int __constant_test_bit(int nr, const volatile void * addr);
+extern int __test_bit(int nr, volatile void * addr);
+extern int find_first_zero_bit(void * addr, unsigned size);
+extern int find_next_zero_bit (void * addr, int size, int offset);
+
+/*
+ * ffz = Find First Zero in word. Undefined if no zero exists,
+ * so code should check against ~0UL first..
+ */
+extern __inline__ unsigned long ffz(unsigned long word)
+{
+	unsigned long result = 0;
+
+	while(word & 1) {
+		result++;
+		word >>= 1;
+	}
+	return result;
+}
+
+
+extern __inline__ void set_bit(int nr, volatile void * addr)
+{
+	int	* a = (int *) addr;
+	int	mask;
+	unsigned long flags;
+
+	a += nr >> 5;
+	mask = 1 << (nr & 0x1f);
+	save_flags_cli(flags);
+	*a |= mask;
+	restore_flags(flags);
+}
+
+extern __inline__ void __set_bit(int nr, volatile void * addr)
+{
+	int	* a = (int *) addr;
+	int	mask;
+
+	a += nr >> 5;
+	mask = 1 << (nr & 0x1f);
+	*a |= mask;
+}
+
+/*
+ * clear_bit() doesn't provide any barrier for the compiler.
+ */
+#define smp_mb__before_clear_bit()	barrier()
+#define smp_mb__after_clear_bit()	barrier()
+
+extern __inline__ void clear_bit(int nr, volatile void * addr)
+{
+	int	* a = (int *) addr;
+	int	mask;
+	unsigned long flags;
+
+	a += nr >> 5;
+	mask = 1 << (nr & 0x1f);
+	save_flags_cli(flags);
+	*a &= ~mask;
+	restore_flags(flags);
+}
+
+extern __inline__ void change_bit(int nr, volatile void * addr)
+{
+	int mask;
+	unsigned long flags;
+	unsigned long *ADDR = (unsigned long *) addr;
+
+	ADDR += nr >> 5;
+	mask = 1 << (nr & 31);
+	save_flags_cli(flags);
+	*ADDR ^= mask;
+	restore_flags(flags);
+}
+
+extern __inline__ void __change_bit(int nr, volatile void * addr)
+{
+	int mask;
+	unsigned long *ADDR = (unsigned long *) addr;
+
+	ADDR += nr >> 5;
+	mask = 1 << (nr & 31);
+	*ADDR ^= mask;
+}
+
+extern __inline__ int test_and_set_bit(int nr, volatile void * addr)
+{
+	int	mask, retval;
+	volatile unsigned int *a = (volatile unsigned int *) addr;
+	unsigned long flags;
+
+	a += nr >> 5;
+	mask = 1 << (nr & 0x1f);
+	save_flags_cli(flags);
+	retval = (mask & *a) != 0;
+	*a |= mask;
+	restore_flags(flags);
+
+	return retval;
+}
+
+extern __inline__ int __test_and_set_bit(int nr, volatile void * addr)
+{
+	int	mask, retval;
+	volatile unsigned int *a = (volatile unsigned int *) addr;
+
+	a += nr >> 5;
+	mask = 1 << (nr & 0x1f);
+	retval = (mask & *a) != 0;
+	*a |= mask;
+	return retval;
+}
+
+extern __inline__ int test_and_clear_bit(int nr, volatile void * addr)
+{
+	int	mask, retval;
+	volatile unsigned int *a = (volatile unsigned int *) addr;
+	unsigned long flags;
+
+	a += nr >> 5;
+	mask = 1 << (nr & 0x1f);
+	save_flags_cli(flags);
+	retval = (mask & *a) != 0;
+	*a &= ~mask;
+	restore_flags(flags);
+
+	return retval;
+}
+
+extern __inline__ int __test_and_clear_bit(int nr, volatile void * addr)
+{
+	int	mask, retval;
+	volatile unsigned int *a = (volatile unsigned int *) addr;
+
+	a += nr >> 5;
+	mask = 1 << (nr & 0x1f);
+	retval = (mask & *a) != 0;
+	*a &= ~mask;
+	return retval;
+}
+
+extern __inline__ int test_and_change_bit(int nr, volatile void * addr)
+{
+	int	mask, retval;
+	volatile unsigned int *a = (volatile unsigned int *) addr;
+	unsigned long flags;
+
+	a += nr >> 5;
+	mask = 1 << (nr & 0x1f);
+	save_flags_cli(flags);
+	retval = (mask & *a) != 0;
+	*a ^= mask;
+	restore_flags(flags);
+
+	return retval;
+}
+
+extern __inline__ int __test_and_change_bit(int nr, volatile void * addr)
+{
+	int	mask, retval;
+	volatile unsigned int *a = (volatile unsigned int *) addr;
+
+	a += nr >> 5;
+	mask = 1 << (nr & 0x1f);
+	retval = (mask & *a) != 0;
+	*a ^= mask;
+	return retval;
+}
+
+/*
+ * This routine doesn't need to be atomic.
+ */
+extern __inline__ int __constant_test_bit(int nr, const volatile void * addr)
+{
+	return ((1UL << (nr & 31)) & (((const volatile unsigned int *) addr)[nr >> 5])) != 0;
+}
+
+extern __inline__ int __test_bit(int nr, volatile void * addr)
+{
+	int	* a = (int *) addr;
+	int	mask;
+
+	a += nr >> 5;
+	mask = 1 << (nr & 0x1f);
+	return ((mask & *a) != 0);
+}
+
+#define test_bit(nr,addr) \
+(__builtin_constant_p(nr) ? \
+ __constant_test_bit((nr),(addr)) : \
+ __test_bit((nr),(addr)))
+
+#define find_first_zero_bit(addr, size) \
+	find_next_zero_bit((addr), (size), 0)
+
+extern __inline__ int find_next_zero_bit (void * addr, int size, int offset)
+{
+	unsigned long *p = ((unsigned long *) addr) + (offset >> 5);
+	unsigned long result = offset & ~31UL;
+	unsigned long tmp;
+
+	if (offset >= size)
+		return size;
+	size -= result;
+	offset &= 31UL;
+	if (offset) {
+		tmp = *(p++);
+		tmp |= ~0UL >> (32-offset);
+		if (size < 32)
+			goto found_first;
+		if (~tmp)
+			goto found_middle;
+		size -= 32;
+		result += 32;
+	}
+	while (size & ~31UL) {
+		if (~(tmp = *(p++)))
+			goto found_middle;
+		result += 32;
+		size -= 32;
+	}
+	if (!size)
+		return result;
+	tmp = *p;
+
+found_first:
+	tmp |= ~0UL >> size;
+found_middle:
+	return result + ffz(tmp);
+}
+
+#define ffs(x) generic_ffs(x)
+
+/*
+ * hweightN: returns the hamming weight (i.e. the number
+ * of bits set) of a N-bit word
+ */
+
+#define hweight32(x) generic_hweight32(x)
+#define hweight16(x) generic_hweight16(x)
+#define hweight8(x) generic_hweight8(x)
+
+
+extern __inline__ int ext2_set_bit(int nr, volatile void * addr)
+{
+	int		mask, retval;
+	unsigned long	flags;
+	volatile unsigned char	*ADDR = (unsigned char *) addr;
+
+	ADDR += nr >> 3;
+	mask = 1 << (nr & 0x07);
+	save_flags_cli(flags);
+	retval = (mask & *ADDR) != 0;
+	*ADDR |= mask;
+	restore_flags(flags);
+	return retval;
+}
+
+extern __inline__ int ext2_clear_bit(int nr, volatile void * addr)
+{
+	int		mask, retval;
+	unsigned long	flags;
+	volatile unsigned char	*ADDR = (unsigned char *) addr;
+
+	ADDR += nr >> 3;
+	mask = 1 << (nr & 0x07);
+	save_flags_cli(flags);
+	retval = (mask & *ADDR) != 0;
+	*ADDR &= ~mask;
+	restore_flags(flags);
+	return retval;
+}
+
+extern __inline__ int ext2_test_bit(int nr, const volatile void * addr)
+{
+	int			mask;
+	const volatile unsigned char	*ADDR = (const unsigned char *) addr;
+
+	ADDR += nr >> 3;
+	mask = 1 << (nr & 0x07);
+	return ((mask & *ADDR) != 0);
+}
+
+#define ext2_find_first_zero_bit(addr, size) \
+	ext2_find_next_zero_bit((addr), (size), 0)
+
+extern __inline__ unsigned long ext2_find_next_zero_bit(void *addr, unsigned long size, unsigned long offset)
+{
+	unsigned long *p = ((unsigned long *) addr) + (offset >> 5);
+	unsigned long result = offset & ~31UL;
+	unsigned long tmp;
+
+	if (offset >= size)
+		return size;
+	size -= result;
+	offset &= 31UL;
+	if(offset) {
+		/* We hold the little endian value in tmp, but then the
+		 * shift is illegal. So we could keep a big endian value
+		 * in tmp, like this:
+		 *
+		 * tmp = __swab32(*(p++));
+		 * tmp |= ~0UL >> (32-offset);
+		 *
+		 * but this would decrease preformance, so we change the
+		 * shift:
+		 */
+		tmp = *(p++);
+		tmp |= __swab32(~0UL >> (32-offset));
+		if(size < 32)
+			goto found_first;
+		if(~tmp)
+			goto found_middle;
+		size -= 32;
+		result += 32;
+	}
+	while(size & ~31UL) {
+		if(~(tmp = *(p++)))
+			goto found_middle;
+		result += 32;
+		size -= 32;
+	}
+	if(!size)
+		return result;
+	tmp = *p;
+
+found_first:
+	/* tmp is little endian, so we would have to swab the shift,
+	 * see above. But then we have to swab tmp below for ffz, so
+	 * we might as well do this here.
+	 */
+	return result + ffz(__swab32(tmp) | (~0UL << size));
+found_middle:
+	return result + ffz(__swab32(tmp));
+}
+
+/* Bitmap functions for the minix filesystem.  */
+#define minix_test_and_set_bit(nr,addr) test_and_set_bit(nr,addr)
+#define minix_set_bit(nr,addr) set_bit(nr,addr)
+#define minix_test_and_clear_bit(nr,addr) test_and_clear_bit(nr,addr)
+#define minix_test_bit(nr,addr) test_bit(nr,addr)
+#define minix_find_first_zero_bit(addr,size) find_first_zero_bit(addr,size)
+
+/**
+ * hweightN - returns the hamming weight of a N-bit word
+ * @x: the word to weigh
+ *
+ * The Hamming Weight of a number is the total number of bits set in it.
+ */
+
+#define hweight32(x) generic_hweight32(x)
+#define hweight16(x) generic_hweight16(x)
+#define hweight8(x) generic_hweight8(x)
+
+#endif /* __KERNEL__ */
+
+#endif /* _MICROBLAZE_BITOPS_H */

include/asm-microblaze/byteorder.h

@@ -0,0 +1,53 @@
+/*
+ * include/asm-microblaze/byteorder.h -- Endian id and conversion ops
+ *
+ *  Copyright (C) 2003  John Williams <jwilliams@itee.uq.edu.au>
+ *  Copyright (C) 2001  NEC Corporation
+ *  Copyright (C) 2001  Miles Bader <miles@gnu.org>
+ *
+ * This file is subject to the terms and conditions of the GNU General
+ * Public License.  See the file COPYING in the main directory of this
+ * archive for more details.
+ *
+ * Written by Miles Bader <miles@gnu.org>
+ * Microblaze port by John Williams
+ */
+
+#ifndef __MICROBLAZE_BYTEORDER_H__
+#define __MICROBLAZE_BYTEORDER_H__
+
+#include <asm/types.h>
+
+#ifdef __GNUC__
+
+/* This is effectively a dupe of the arch-independent byteswap
+   code in include/linux/byteorder/swab.h, however we force a cast
+   of the result up to 32 bits.  This in turn forces the compiler
+   to explicitly clear the high 16 bits, which it wasn't doing otherwise.
+
+   I think this is a symptom of a bug in mb-gcc.  JW 20040303
+*/
+static __inline__ __const__ __u16 ___arch__swab16 (__u16 half_word)
+{
+	/* 32 bit temp to cast result, forcing clearing of high word */
+	__u32 temp;
+
+	temp = ((half_word & 0x00FFU) << 8) | ((half_word & 0xFF00U) >> 8);
+
+	return (__u16) temp;
+}
+
+#define __arch__swab16(x) ___arch__swab16(x)
+
+/* Microblaze has no arch-specific endian conversion insns */
+
+#if !defined(__STRICT_ANSI__) || defined(__KERNEL__)
+#  define __BYTEORDER_HAS_U64__
+#  define __SWAB_64_THRU_32__
+#endif
+
+#endif /* __GNUC__ */
+
+#include <linux/byteorder/big_endian.h>
+
+#endif /* __MICROBLAZE_BYTEORDER_H__ */

include/asm-microblaze/global_data.h

@@ -0,0 +1,58 @@
+/*
+ * (C) Copyright 2004 Atmark Techno, Inc.
+ *
+ * Yasushi SHOJI <yashi@atmark-techno.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef	__ASM_GBL_DATA_H
+#define __ASM_GBL_DATA_H
+/*
+ * The following data structure is placed in some memory wich is
+ * available very early after boot (like DPRAM on MPC8xx/MPC82xx, or
+ * some locked parts of the data cache) to allow for a minimum set of
+ * global variables during system initialization (until we have set
+ * up the memory controller so that we can use RAM).
+ *
+ * Keep it *SMALL* and remember to set CFG_GBL_DATA_SIZE > sizeof(gd_t)
+ */
+
+typedef	struct	global_data {
+	bd_t		*bd;
+	unsigned long	flags;
+	unsigned long	baudrate;
+	unsigned long	have_console;	/* serial_init() was called */
+	unsigned long	reloc_off;	/* Relocation Offset */
+	unsigned long	env_addr;	/* Address  of Environment struct */
+	unsigned long	env_valid;	/* Checksum of Environment valid? */
+	unsigned long	fb_base;	/* base address of frame buffer */
+	void		**jt;		/* jump table */
+} gd_t;
+
+/*
+ * Global Data Flags
+ */
+#define	GD_FLG_RELOC	0x00001		/* Code was relocated to RAM		*/
+#define	GD_FLG_DEVINIT	0x00002		/* Devices have been initialized	*/
+#define	GD_FLG_SILENT	0x00004		/* Silent mode				*/
+
+#define DECLARE_GLOBAL_DATA_PTR     register volatile gd_t *gd asm ("r31")
+
+#endif /* __ASM_GBL_DATA_H */

include/asm-microblaze/io.h

@@ -0,0 +1,128 @@
+/*
+ * include/asm-microblaze/io.h -- Misc I/O operations
+ *
+ *  Copyright (C) 2003     John Williams <jwilliams@itee.uq.edu.au>
+ *  Copyright (C) 2001,02  NEC Corporation
+ *  Copyright (C) 2001,02  Miles Bader <miles@gnu.org>
+ *
+ * This file is subject to the terms and conditions of the GNU General
+ * Public License.  See the file COPYING in the main directory of this
+ * archive for more details.
+ *
+ * Written by Miles Bader <miles@gnu.org>
+ * Microblaze port by John Williams
+ */
+
+#ifndef __MICROBLAZE_IO_H__
+#define __MICROBLAZE_IO_H__
+
+#define IO_SPACE_LIMIT 0xFFFFFFFF
+
+#define readb(addr) \
+  ({ unsigned char __v = (*(volatile unsigned char *) (addr)); __v; })
+#define readw(addr) \
+  ({ unsigned short __v = (*(volatile unsigned short *) (addr)); __v; })
+#define readl(addr) \
+  ({ unsigned long __v = (*(volatile unsigned long *) (addr)); __v; })
+
+#define writeb(b, addr) \
+  (void)((*(volatile unsigned char *) (addr)) = (b))
+#define writew(b, addr) \
+  (void)((*(volatile unsigned short *) (addr)) = (b))
+#define writel(b, addr) \
+  (void)((*(volatile unsigned int *) (addr)) = (b))
+
+#define memset_io(a,b,c)        memset((void *)(a),(b),(c))
+#define memcpy_fromio(a,b,c)    memcpy((a),(void *)(b),(c))
+#define memcpy_toio(a,b,c)      memcpy((void *)(a),(b),(c))
+
+#define inb(addr)	readb (addr)
+#define inw(addr)	readw (addr)
+#define inl(addr)	readl (addr)
+#define outb(x, addr)	((void) writeb (x, addr))
+#define outw(x, addr)	((void) writew (x, addr))
+#define outl(x, addr)	((void) writel (x, addr))
+
+/* Some #definitions to keep strange Xilinx code happy */
+#define in_8(addr)	readb (addr)
+#define in_be16(addr)	readw (addr)
+#define in_be32(addr)	readl (addr)
+
+#define out_8(addr,x )	outb (x,addr)
+#define out_be16(addr,x )	outw (x,addr)
+#define out_be32(addr,x )	outl (x,addr)
+
+
+#define inb_p(port)		inb((port))
+#define outb_p(val, port)	outb((val), (port))
+#define inw_p(port)		inw((port))
+#define outw_p(val, port)	outw((val), (port))
+#define inl_p(port)		inl((port))
+#define outl_p(val, port)	outl((val), (port))
+
+/* Some defines to keep the MTD flash drivers happy */
+
+#define __raw_readb readb
+#define __raw_readw readw
+#define __raw_readl readl
+#define __raw_writeb writeb
+#define __raw_writew writew
+#define __raw_writel writel
+
+static inline void io_insb (unsigned long port, void *dst, unsigned long count)
+{
+	unsigned char *p = dst;
+	while (count--)
+		*p++ = inb (port);
+}
+static inline void io_insw (unsigned long port, void *dst, unsigned long count)
+{
+	unsigned short *p = dst;
+	while (count--)
+		*p++ = inw (port);
+}
+static inline void io_insl (unsigned long port, void *dst, unsigned long count)
+{
+	unsigned long *p = dst;
+	while (count--)
+		*p++ = inl (port);
+}
+
+static inline void
+io_outsb (unsigned long port, const void *src, unsigned long count)
+{
+	const unsigned char *p = src;
+	while (count--)
+		outb (*p++, port);
+}
+static inline void
+io_outsw (unsigned long port, const void *src, unsigned long count)
+{
+	const unsigned short *p = src;
+	while (count--)
+		outw (*p++, port);
+}
+static inline void
+io_outsl (unsigned long port, const void *src, unsigned long count)
+{
+	const unsigned long *p = src;
+	while (count--)
+		outl (*p++, port);
+}
+
+#define outsb(a,b,l) io_outsb(a,b,l)
+#define outsw(a,b,l) io_outsw(a,b,l)
+#define outsl(a,b,l) io_outsl(a,b,l)
+
+#define insb(a,b,l) io_insb(a,b,l)
+#define insw(a,b,l) io_insw(a,b,l)
+#define insl(a,b,l) io_insl(a,b,l)
+
+
+#define iounmap(addr)				((void)0)
+#define ioremap(physaddr, size)			(physaddr)
+#define ioremap_nocache(physaddr, size)		(physaddr)
+#define ioremap_writethrough(physaddr, size)	(physaddr)
+#define ioremap_fullcache(physaddr, size)	(physaddr)
+
+#endif /* __MICROBLAZE_IO_H__ */

include/asm-microblaze/platform.h

@@ -0,0 +1,29 @@
+/*
+ * (C) Copyright 2004 Atmark Techno, Inc.
+ *
+ * Yasushi SHOJI <yashi@atmark-techno.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+
+#ifdef CONFIG_SUZAKU
+#include <asm/suzaku.h>
+#endif

include/asm-microblaze/posix_types.h

@@ -0,0 +1,76 @@
+/*
+ * include/asm-microblaze/posix_types.h -- Kernel versions of standard types
+ *
+ *  Copyright (C) 2003       John Williams <jwilliams@itee.uq.edu.au>
+ *  Copyright (C) 2001,2002  NEC Corporation
+ *  Copyright (C) 2001,2002  Miles Bader <miles@gnu.org>
+ *
+ * This file is subject to the terms and conditions of the GNU General
+ * Public License.  See the file COPYING in the main directory of this
+ * archive for more details.
+ *
+ * Written by Miles Bader <miles@gnu.org>
+ * Microblaze port by John Williams
+ */
+
+#ifndef __MICROBLAZE_POSIX_TYPES_H__
+#define __MICROBLAZE_POSIX_TYPES_H__
+
+#include <asm/bitops.h>
+
+
+typedef unsigned int	__kernel_dev_t;
+typedef unsigned long	__kernel_ino_t;
+typedef unsigned long long __kernel_ino64_t;
+typedef unsigned int	__kernel_mode_t;
+typedef unsigned int	__kernel_nlink_t;
+typedef long		__kernel_off_t;
+typedef long long	__kernel_loff_t;
+typedef int		__kernel_pid_t;
+typedef unsigned short	__kernel_ipc_pid_t;
+typedef unsigned int	__kernel_uid_t;
+typedef unsigned int	__kernel_gid_t;
+typedef unsigned int	__kernel_size_t;
+typedef int		__kernel_ssize_t;
+typedef int		__kernel_ptrdiff_t;
+typedef long		__kernel_time_t;
+typedef long		__kernel_suseconds_t;
+typedef long		__kernel_clock_t;
+typedef int		__kernel_daddr_t;
+typedef char *		__kernel_caddr_t;
+typedef unsigned short	__kernel_uid16_t;
+typedef unsigned short	__kernel_gid16_t;
+typedef unsigned int	__kernel_uid32_t;
+typedef unsigned int	__kernel_gid32_t;
+
+typedef unsigned short	__kernel_old_uid_t;
+typedef unsigned short	__kernel_old_gid_t;
+
+
+typedef struct {
+#if defined(__KERNEL__) || defined(__USE_ALL)
+	int	val[2];
+#else /* !defined(__KERNEL__) && !defined(__USE_ALL) */
+	int	__val[2];
+#endif /* !defined(__KERNEL__) && !defined(__USE_ALL) */
+} __kernel_fsid_t;
+
+
+#if defined(__KERNEL__) || !defined(__GLIBC__) || (__GLIBC__ < 2)
+
+#undef	__FD_SET
+#define __FD_SET(fd, fd_set) \
+  __set_bit (fd, (void *)&((__kernel_fd_set *)fd_set)->fds_bits)
+#undef __FD_CLR
+#define __FD_CLR(fd, fd_set) \
+  __clear_bit (fd, (void *)&((__kernel_fd_set *)fd_set)->fds_bits)
+#undef	__FD_ISSET
+#define __FD_ISSET(fd, fd_set) \
+  __test_bit (fd, (void *)&((__kernel_fd_set *)fd_set)->fds_bits)
+#undef	__FD_ZERO
+#define __FD_ZERO(fd_set) \
+  memset (fd_set, 0, sizeof (*(fd_set *)fd_set))
+
+#endif /* defined(__KERNEL__) || !defined(__GLIBC__) || (__GLIBC__ < 2) */
+
+#endif /* __MICROBLAZE_POSIX_TYPES_H__ */

include/asm-microblaze/ptrace.h

@@ -0,0 +1,116 @@
+/*
+ * include/asm-microblaze/ptrace.h -- Access to CPU registers
+ *
+ *  Copyright (C) 2003       John Williams <jwilliams@itee.uq.edu.au>
+ *  Copyright (C) 2001,2002  NEC Corporation
+ *  Copyright (C) 2001,2002  Miles Bader <miles@gnu.org>
+ *
+ * This file is subject to the terms and conditions of the GNU General
+ * Public License.  See the file COPYING in the main directory of this
+ * archive for more details.
+ *
+ * Written by Miles Bader <miles@gnu.org>
+ * Microblaze port by John Williams
+ */
+
+#ifndef __MICROBLAZE_PTRACE_H__
+#define __MICROBLAZE_PTRACE_H__
+
+
+/* Microblaze general purpose registers with special meanings.  */
+#define GPR_ZERO	0	/* constant zero */
+#define GPR_ASM		18	/* reserved for assembler */
+#define GPR_SP		1	/* stack pointer */
+#define GPR_GP		2	/* global data pointer */
+#define GPR_EP		30	/* `element pointer' */
+#define GPR_LP		15	/* link pointer (current return address) */
+
+/* These aren't official names, but they make some code more descriptive.  */
+#define GPR_ARG0	5
+#define GPR_ARG1	6
+#define GPR_ARG2	7
+#define GPR_ARG3	8
+#define GPR_ARG4	9
+#define GPR_ARG5	10
+#define GPR_RVAL0	3
+#define GPR_RVAL1	4
+#define GPR_RVAL	GPR_RVAL0
+
+#define NUM_GPRS	32
+
+/* `system' registers.  */
+/* Note these are old v850 values, microblaze has many fewer */
+#define SR_EIPC		0
+#define SR_EIPSW	1
+#define SR_FEPC		2
+#define SR_FEPSW	3
+#define SR_ECR		4
+#define SR_PSW		5
+#define SR_CTPC		16
+#define SR_CTPSW	17
+#define SR_DBPC		18
+#define SR_DBPSW	19
+#define SR_CTBP		20
+#define SR_DIR		21
+#define SR_ASID		23
+
+
+#ifndef __ASSEMBLY__
+
+typedef unsigned long microblaze_reg_t;
+
+/* How processor state is stored on the stack during a syscall/signal.
+   If you change this structure, change the associated assembly-language
+   macros below too (PT_*)!  */
+struct pt_regs
+{
+	/* General purpose registers.  */
+	microblaze_reg_t gpr[NUM_GPRS];
+
+	microblaze_reg_t pc;		/* program counter */
+	microblaze_reg_t psw;		/* program status word */
+
+	microblaze_reg_t kernel_mode;	/* 1 if in `kernel mode', 0 if user mode */
+	microblaze_reg_t single_step;	/* 1 if in single step mode */
+};
+
+
+#define instruction_pointer(regs)	((regs)->pc)
+#define user_mode(regs)			(!(regs)->kernel_mode)
+
+/* When a struct pt_regs is used to save user state for a system call in
+   the kernel, the system call is stored in the space for R0 (since it's
+   never used otherwise, R0 being a constant 0).  Non-system-calls
+   simply store 0 there.  */
+#define PT_REGS_SYSCALL(regs)		(regs)->gpr[0]
+#define PT_REGS_SET_SYSCALL(regs, val)	((regs)->gpr[0] = (val))
+
+#endif /* !__ASSEMBLY__ */
+
+
+/* The number of bytes used to store each register.  */
+#define _PT_REG_SIZE	4
+
+/* Offset of a general purpose register in a stuct pt_regs.  */
+#define PT_GPR(num)	((num) * _PT_REG_SIZE)
+
+/* Offsets of various special registers & fields in a struct pt_regs.  */
+#define NUM_SPECIAL	4
+#define PT_PC		((NUM_GPRS + 0) * _PT_REG_SIZE)
+#define PT_PSW		((NUM_GPRS + 1) * _PT_REG_SIZE)
+#define PT_KERNEL_MODE	((NUM_GPRS + 2) * _PT_REG_SIZE)
+#define PT_SINGLESTEP	((NUM_GPRS + 3) * _PT_REG_SIZE)
+
+#define PT_SYSCALL	PT_GPR(0)
+
+/* Size of struct pt_regs, including alignment.  */
+#define PT_SIZE		((NUM_GPRS + NUM_SPECIAL) * _PT_REG_SIZE)
+
+/* These are `magic' values for PTRACE_PEEKUSR that return info about where
+   a process is located in memory.  */
+#define PT_TEXT_ADDR    (PT_SIZE + 1)
+#define PT_TEXT_LEN     (PT_SIZE + 2)
+#define PT_DATA_ADDR    (PT_SIZE + 3)
+#define PT_DATA_LEN     (PT_SIZE + 4)
+
+#endif /* __MICROBLAZE_PTRACE_H__ */

include/asm-microblaze/serial_xuartlite.h

@@ -0,0 +1,25 @@
+/*
+ * (C) Copyright 2004 Atmark Techno, Inc.
+ *
+ * Yasushi SHOJI <yashi@atmark-techno.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <asm/arch/xuartlite_l.h>

include/asm-microblaze/string.h

@@ -0,0 +1,31 @@
+/*
+ * include/asm-microblaze/string.h -- Architecture specific string routines
+ *
+ *  Copyright (C) 2003       John Williams <jwilliams@itee.uq.edu.au>
+ *  Copyright (C) 2001,2002  NEC Corporation
+ *  Copyright (C) 2001,2002  Miles Bader <miles@gnu.org>
+ *
+ * This file is subject to the terms and conditions of the GNU General
+ * Public License.  See the file COPYING in the main directory of this
+ * archive for more details.
+ *
+ * Written by Miles Bader <miles@gnu.org>
+ * Microblaze port by John Williams
+ */
+
+#ifndef __MICROBLAZE_STRING_H__
+#define __MICROBLAZE_STRING_H__
+
+#if 0
+#define __HAVE_ARCH_BCOPY
+#define __HAVE_ARCH_MEMCPY
+#define __HAVE_ARCH_MEMSET
+#define __HAVE_ARCH_MEMMOVE
+
+extern void *memcpy (void *, const void *, __kernel_size_t);
+extern void bcopy (const char *, char *, int);
+extern void *memset (void *, int, __kernel_size_t);
+extern void *memmove (void *, const void *, __kernel_size_t);
+#endif
+
+#endif /* __MICROBLAZE_STRING_H__ */

include/asm-microblaze/suzaku.h

@@ -0,0 +1,25 @@
+/*
+ * (C) Copyright 2004 Atmark Techno, Inc.
+ *
+ * Yasushi SHOJI <yashi@atmark-techno.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/* EMPTY FILE */

include/asm-microblaze/system.h

@@ -0,0 +1,161 @@
+/*
+ * include/asm-microblaze/system.h -- Low-level interrupt/thread ops
+ *
+ *  Copyright (C) 2003	John Williams (jwilliams@itee.uq.edu.au)
+ *			based upon microblaze version
+ *  Copyright (C) 2001	NEC Corporation
+ *  Copyright (C) 2001	Miles Bader <miles@gnu.org>
+ *
+ * This file is subject to the terms and conditions of the GNU General
+ * Public License.  See the file COPYING in the main directory of this
+ * archive for more details.
+ *
+ * Written by Miles Bader <miles@gnu.org>
+ * Microblaze port by John Williams
+ * Microblaze port by John Williams
+ */
+
+#ifndef __MICROBLAZE_SYSTEM_H__
+#define __MICROBLAZE_SYSTEM_H__
+
+#if 0
+#include <linux/linkage.h>
+#endif
+#include <asm/ptrace.h>
+
+#define prepare_to_switch()	do { } while (0)
+
+/*
+ * switch_to(n) should switch tasks to task ptr, first checking that
+ * ptr isn't the current task, in which case it does nothing.
+ */
+struct thread_struct;
+extern void *switch_thread (struct thread_struct *last,
+			    struct thread_struct *next);
+#define switch_to(prev,next,last) do {					\
+	if (prev != next) {						\
+		(last) = switch_thread (&prev->thread, &next->thread);	\
+	}								\
+} while (0)
+
+
+/* Enable/disable interrupts.  */
+#define __sti() \
+{								\
+	register unsigned tmp;					\
+	__asm__ __volatile__ ("					\
+			mfs	%0, rmsr;			\
+			ori	%0, %0, 2;			\
+			mts	rmsr, %0"			\
+			: "=r" (tmp)				\
+			:					\
+			: "memory");				\
+}
+
+#define __cli() \
+{								\
+	register unsigned tmp;					\
+	__asm__ __volatile__ ("					\
+			mfs	%0, rmsr;			\
+			andi	%0, %0, ~2;			\
+			mts	rmsr, %0"			\
+			: "=r" (tmp)				\
+			:					\
+			: "memory");				\
+}
+
+#define __save_flags(flags) \
+	__asm__ __volatile__ ("mfs	%0, rmsr" : "=r" (flags))
+#define __restore_flags(flags) \
+	__asm__ __volatile__ ("mts	rmsr, %0" :: "r" (flags))
+
+#define __save_flags_cli(flags) \
+{								\
+	register unsigned tmp;					\
+	__asm__ __volatile__ ("					\
+			mfs	%0, rmsr;			\
+			andi	%1, %0, ~2;			\
+			mts	rmsr, %1;"			\
+			: "=r" (flags), "=r" (tmp)		\
+			:					\
+			: "memory");				\
+}
+
+#define __save_flags_sti(flags)					\
+{								\
+	register unsigned tmp;					\
+	__asm__ __volatile__ ("					\
+			mfs	%0, rmsr;			\
+			ori	%1, %0, 2;			\
+			mts	rmsr, %1;"			\
+			: "=r" (flags) ,"=r" (tmp)		\
+			:					\
+			: "memory");				\
+}
+
+/* For spinlocks etc */
+#define local_irq_save(flags)	__save_flags_cli (flags)
+#define local_irq_set(flags)	__save_flags_sti (flags)
+#define local_irq_restore(flags) __restore_flags (flags)
+#define local_irq_disable()	__cli ()
+#define local_irq_enable()	__sti ()
+
+#define cli()			__cli ()
+#define sti()			__sti ()
+#define save_flags(flags)	__save_flags (flags)
+#define restore_flags(flags)	__restore_flags (flags)
+#define save_flags_cli(flags)	__save_flags_cli (flags)
+
+/*
+ * Force strict CPU ordering.
+ * Not really required on microblaze...
+ */
+#define nop()			__asm__ __volatile__ ("nop")
+#define mb()			__asm__ __volatile__ ("nop" ::: "memory")
+#define rmb()			mb ()
+#define wmb()			mb ()
+#define set_mb(var, value)	do { var = value; mb(); } while (0)
+#define set_wmb(var, value)	do { var = value; wmb (); } while (0)
+
+#ifdef CONFIG_SMP
+#define smp_mb()	mb ()
+#define smp_rmb()	rmb ()
+#define smp_wmb()	wmb ()
+#else
+#define smp_mb()	barrier ()
+#define smp_rmb()	barrier ()
+#define smp_wmb()	barrier ()
+#endif
+
+#define xchg(ptr, with) \
+  ((__typeof__ (*(ptr)))__xchg ((unsigned long)(with), (ptr), sizeof (*(ptr))))
+#define tas(ptr) (xchg ((ptr), 1))
+
+extern inline unsigned long __xchg (unsigned long with,
+				    __volatile__ void *ptr, int size)
+{
+	unsigned long tmp, flags;
+
+	save_flags_cli (flags);
+
+	switch (size) {
+	case 1:
+		tmp = *(unsigned char *)ptr;
+		*(unsigned char *)ptr = with;
+		break;
+	case 2:
+		tmp = *(unsigned short *)ptr;
+		*(unsigned short *)ptr = with;
+		break;
+	case 4:
+		tmp = *(unsigned long *)ptr;
+		*(unsigned long *)ptr = with;
+		break;
+	}
+
+	restore_flags (flags);
+
+	return tmp;
+}
+
+#endif /* __MICROBLAZE_SYSTEM_H__ */

include/asm-microblaze/types.h

@@ -0,0 +1,57 @@
+#ifndef _ASM_TYPES_H
+#define _ASM_TYPES_H
+
+/*
+ * This file is never included by application software unless
+ * explicitly requested (e.g., via linux/types.h) in which case the
+ * application is Linux specific so (user-) name space pollution is
+ * not a major issue.  However, for interoperability, libraries still
+ * need to be careful to avoid a name clashes.
+ */
+
+typedef unsigned short umode_t;
+
+/*
+ * __xx is ok: it doesn't pollute the POSIX namespace. Use these in the
+ * header files exported to user space
+ */
+
+typedef __signed__ char __s8;
+typedef unsigned char __u8;
+
+typedef __signed__ short __s16;
+typedef unsigned short __u16;
+
+typedef __signed__ int __s32;
+typedef unsigned int __u32;
+
+#if defined(__GNUC__) && !defined(__STRICT_ANSI__)
+typedef __signed__ long long __s64;
+typedef unsigned long long __u64;
+#endif
+
+/*
+ * These aren't exported outside the kernel to avoid name space clashes
+ */
+#ifdef __KERNEL__
+
+typedef signed char s8;
+typedef unsigned char u8;
+
+typedef signed short s16;
+typedef unsigned short u16;
+
+typedef signed int s32;
+typedef unsigned int u32;
+
+typedef signed long long s64;
+typedef unsigned long long u64;
+
+#define BITS_PER_LONG 32
+
+/* Dma addresses are 32-bits wide.  */
+
+typedef u32 dma_addr_t;
+#endif /* __KERNEL__ */
+
+#endif /* _ASM_TYPES_H */

include/asm-microblaze/u-boot.h

@@ -0,0 +1,42 @@
+/*
+ * (C) Copyright 2004 Atmark Techno, Inc.
+ *
+ * Yasushi SHOJI <yashi@atmark-techno.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef _U_BOOT_H_
+#define _U_BOOT_H_
+
+typedef struct bd_info {
+	unsigned long	bi_memstart;	/* start of DRAM memory */
+	unsigned long	bi_memsize;	/* size	 of DRAM memory in bytes */
+	unsigned long	bi_flashstart;	/* start of FLASH memory */
+	unsigned long	bi_flashsize;	/* size	 of FLASH memory */
+	unsigned long	bi_flashoffset; /* reserved area for startup monitor */
+	unsigned long	bi_sramstart;	/* start of SRAM memory */
+	unsigned long	bi_sramsize;	/* size	 of SRAM memory */
+	unsigned long	bi_ip_addr;	/* IP Address */
+	unsigned char	bi_enetaddr[6]; /* Ethernet adress */
+	unsigned long	bi_baudrate;	/* Console Baudrate */
+} bd_t;
+
+
+#endif	/* _U_BOOT_H_ */

include/asm-ppc/immap_8260.h

@@ -135,17 +135,21 @@ typedef struct pci_config {
 	uint	pci_imimr;
 	char	res5[24];
 	uint	pci_ifhpr;
+	char	res5_2[4];
 	uint	pci_iftpr;
-	char	res6[8];
+	char	res6[4];
 	uint	pci_iphpr;
+	char	res6_2[4];
 	uint	pci_iptpr;
-	char	res7[8];
+	char	res7[4];
 	uint	pci_ofhpr;
+	char	res7_2[4];
 	uint	pci_oftpr;
-	char	res8[8];
+	char	res8[4];
 	uint	pci_ophpr;
+	char	res8_2[4];
 	uint	pci_optpr;
-	char	res9[12];
+	char	res9[8];
 	uint	pci_mucr;
 	char	res10[8];
 	uint	pci_qbar;

include/configs/JSE.h

@@ -152,7 +152,7 @@
   /* watchdog disabled */
 #undef CONFIG_WATCHDOG
   /* SPD EEPROM (sdram speed config) disabled */
-#undef CONFIG_SPD_EEPRO
+#undef CONFIG_SPD_EEPROM
 #undef SPD_EEPROM_ADDRESS
 
 /*

include/configs/KUP4X.h

@@ -118,7 +118,9 @@
 #define CONFIG_COMMANDS	      ( CONFIG_CMD_DFL	| \
 				CFG_CMD_DHCP	| \
 				CFG_CMD_I2C	| \
-				CFG_CMD_IDE	)
+				CFG_CMD_IDE	| \
+				CFG_CMD_USB	| \
+				CFG_CMD_FAT)
 
 /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
 #include <cmd_confdefs.h>
@@ -386,4 +388,7 @@
 #define CONFIG_AUTOBOOT_STOP_STR	"."	/* easy to stop for now		*/
 #define CONFIG_SILENT_CONSOLE	1
 
+#define CONFIG_USB_STORAGE	1
+#define CONFIG_USB_SL811HS	1
+
 #endif	/* __CONFIG_H */

include/configs/NETPHONE.h

@@ -67,8 +67,8 @@
 #undef	CONFIG_BOOTARGS
 #define CONFIG_BOOTCOMMAND							\
 	"tftpboot; " 								\
-	"setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " 	\
-	"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off; " 	\
+	"setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " 	\
+	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " 	\
 	"bootm"
 
 #define CONFIG_AUTOSCRIPT

include/configs/NETTA.h

@@ -65,8 +65,8 @@
 #undef	CONFIG_BOOTARGS
 #define CONFIG_BOOTCOMMAND							\
 	"tftpboot; " 								\
-	"setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " 	\
-	"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off; " 	\
+	"setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " 	\
+	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " 	\
 	"bootm"
 
 #define CONFIG_LOADS_ECHO	0	/* echo off for serial download	*/

include/configs/NETVIA.h

@@ -64,8 +64,8 @@
 #undef	CONFIG_BOOTARGS
 #define CONFIG_BOOTCOMMAND							\
 	"tftpboot; " 								\
-	"setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " 	\
-	"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off; " 	\
+	"setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " 	\
+	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " 	\
 	"bootm"
 
 #define CONFIG_LOADS_ECHO	0	/* echo off for serial download	*/

include/configs/TOP5200.h

@@ -94,7 +94,11 @@
 
 #  define CONFIG_USB_OHCI
 #  define CONFIG_USB_CLOCK	0x0001bbbb
-#  define CONFIG_USB_CONFIG	0x00005000
+#  if defined (CONFIG_EVAL5200)
+#    define CONFIG_USB_CONFIG	0x00005100
+#  else
+#    define CONFIG_USB_CONFIG	0x00001000
+#  endif
 #  define ADD_USB_CMD             CFG_CMD_USB | CFG_CMD_FAT
 #  define CONFIG_DOS_PARTITION
 #  define CONFIG_USB_STORAGE
@@ -325,7 +329,7 @@
  * PCI disabled
  * Ethernet 100 with MD
  */
-#define CFG_GPS_PORT_CONFIG	0x00058444
+#define CFG_GPS_PORT_CONFIG	0x00058044
 
 /*
  * Miscellaneous configurable options

include/configs/debris.h

@@ -175,7 +175,8 @@
  * Please note that CFG_SDRAM_BASE _must_ start at 0
  */
 #define CFG_SDRAM_BASE		0x00000000
-#define CFG_MAX_RAM_SIZE	0x10000000
+#define CFG_MAX_RAM_SIZE	0x20000000
+#define CONFIG_VERY_BIG_RAM
 
 #define CFG_RESET_ADDRESS	0xFFF00100
 

include/configs/stxgp3.h

@@ -0,0 +1,403 @@
+/*
+ * (C) Copyright 2003 Embedded Edge, LLC
+ * Dan Malek <dan@embeddededge.com>
+ * Copied from ADS85xx.
+ * Updates for Silicon Tx GP3 8560 board.
+ *
+ * (C) Copyright 2002,2003 Motorola,Inc.
+ * Xianghua Xiao <X.Xiao@motorola.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/* mpc8560ads board configuration file */
+/* please refer to doc/README.mpc85xx for more info */
+/* make sure you change the MAC address and other network params first,
+ * search for CONFIG_ETHADDR,CONFIG_SERVERIP,etc in this file
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* High Level Configuration Options */
+#define CONFIG_BOOKE		1	/* BOOKE		*/
+#define CONFIG_E500		1	/* BOOKE e500 family	*/
+#define CONFIG_MPC85xx		1	/* MPC8540/MPC8560	*/
+#define CONFIG_MPC85xx_REV1	1	/* MPC85xx Rev 1.0 chip */
+#define CONFIG_MPC8560		1	/* MPC8560 specific	*/
+#define CONFIG_STXGP3		1	/* Silicon Tx GPPP board specific*/
+
+#undef  CONFIG_PCI	         	/* pci ethernet support	*/
+#define CONFIG_TSEC_ENET 		/* tsec ethernet support*/
+#undef  CONFIG_ETHER_ON_FCC             /* cpm FCC ethernet support */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_SPD_EEPROM               /* Use SPD EEPROM for DDR setup */
+#undef  CONFIG_DDR_ECC			/* only for ECC DDR module */
+
+#if defined(CONFIG_MPC85xx_REV1)
+#define CONFIG_DDR_DLL                  /* possible DLL fix needed */
+#endif
+
+/* Using Localbus SDRAM to emulate flash before we can program the flash,
+ * normally you need a flash-boot image(u-boot.bin), if so undef this.
+ */
+#undef CONFIG_RAM_AS_FLASH
+
+#define CONFIG_SYS_CLK_FREQ     33333333 /* most pci cards are 33Mhz */
+
+/* Blinkin' LEDs for Robert :-)
+*/
+#define CONFIG_SHOW_ACTIVITY 1
+
+#if !defined(CONFIG_SPD_EEPROM)		/* manually set up DDR parameters */
+#define CONFIG_DDR_SETTING
+#endif
+
+/* below can be toggled for performance analysis. otherwise use default */
+#define CONFIG_L2_CACHE                     /* toggle L2 cache         */
+#undef  CONFIG_BTB                          /* toggle branch predition */
+#undef  CONFIG_ADDR_STREAMING               /* toggle addr streaming   */
+
+#define CONFIG_BOARD_PRE_INIT   1           /* Call board_pre_init      */
+
+#undef  CFG_DRAM_TEST                       /* memory test, takes time  */
+#define CFG_MEMTEST_START       0x00200000  /* memtest region */
+#define CFG_MEMTEST_END         0x00400000
+
+#if (defined(CONFIG_PCI) && defined(CONFIG_TSEC_ENET) || \
+     defined(CONFIG_PCI) && defined(CONFIG_ETHER_ON_FCC) || \
+     defined(CONFIG_TSEC_ENET) && defined(CONFIG_ETHER_ON_FCC))
+#error "You can only use ONE of PCI Ethernet Card or TSEC Ethernet or CPM FCC."
+#endif
+
+/*
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ */
+#define CFG_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory  */
+#define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE
+
+/* GPPP supports up to 2G of DRAM.  Allocate up to 1G until we get
+ * a chance to try it out.  Actual size is always read from sdram eeprom.
+ */
+#define CFG_SDRAM_SIZE		1024		/* DDR is 1GB	*/
+
+/* Localbus SDRAM is an option, not all boards have it.
+*/
+#if defined(CONFIG_RAM_AS_FLASH)
+#define CFG_LBC_SDRAM_BASE      0xfc000000      /* Localbus SDRAM */
+#else
+#define CFG_LBC_SDRAM_BASE      0xf8000000      /* Localbus SDRAM */
+#endif
+#define CFG_LBC_SDRAM_SIZE	64		/* LBC SDRAM is 64MB	*/
+
+#if defined(CONFIG_RAM_AS_FLASH)
+#define CFG_FLASH_BASE        0xf8000000      /* start of FLASH  16M  */
+#define CFG_BR0_PRELIM        0xf8001801      /* port size 32bit */
+#else /* Boot from real Flash */
+#define CFG_FLASH_BASE        0xff000000      /* start of FLASH 16M    */
+#define CFG_BR0_PRELIM        0xff001801      /* port size 32bit      */
+#endif
+
+#define CFG_OR0_PRELIM          0xff000ff7      /* 16 MB Flash           */
+#define CFG_MAX_FLASH_BANKS	1		/* number of banks	*/
+#define CFG_MAX_FLASH_SECT	136		/* sectors per device   */
+#undef	CFG_FLASH_CHECKSUM
+#define CFG_FLASH_ERASE_TOUT	60000	/* Timeout for Flash Erase (in ms)	*/
+#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
+
+/* The configuration latch is Chip Select 1.
+ * It's an 8-bit latch in the upper 8 bits of the word.
+ */
+#define CFG_BR1_PRELIM		0xfc001801	/* 32-bit port */
+#define CFG_OR1_PRELIM		0xffff0ff7      /* 64K is enough */
+#define CFG_LBC_LCLDEVS_BASE	0xfc000000	/* Base of localbus devices */
+
+#define CFG_MONITOR_BASE    	TEXT_BASE	/* start of monitor	*/
+
+#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
+#define CFG_RAMBOOT
+#else
+#undef  CFG_RAMBOOT
+#endif
+
+#ifdef CFG_RAMBOOT
+#define CFG_CCSRBAR_DEFAULT 	0x40000000	/* CCSRBAR by BDI cfg	*/
+#else
+#define CFG_CCSRBAR_DEFAULT 	0xff700000	/* CCSRBAR Default	*/
+#endif
+#define CFG_CCSRBAR             0xfdf00000      /* relocated CCSRBAR    */
+#define CFG_IMMR		CFG_CCSRBAR	/* PQII uses CFG_IMMR	*/
+
+
+#define SPD_EEPROM_ADDRESS 	0x54     	/*  DDR DIMM */
+
+#if defined(CONFIG_DDR_SETTING)
+#define	CFG_DDR_CS0_BNDS	0x00000007	/* 0-128MB */
+#define CFG_DDR_CS0_CONFIG	0x80000002
+#define CFG_DDR_TIMING_1	0x37344321
+#define CFG_DDR_TIMING_2	0x00000800	/* P9-45,may need tuning*/
+#define CFG_DDR_CONTROL		0xc2000000	/* unbuffered,no DYN_PWR*/
+#define CFG_DDR_MODE		0x00000062	/* DLL,normal,seq,4/2.5 */
+#define CFG_DDR_INTERVAL	0x05200100	/* autocharge,no open page*/
+#endif
+
+#undef CONFIG_CLOCKS_IN_MHZ
+
+/* local bus definitions */
+#define CFG_BR2_PRELIM		0xf8001861	/* 64MB localbus SDRAM  */
+#define CFG_OR2_PRELIM		0xfc006901
+#define CFG_LBC_LCRR		0x00030004	/* local bus freq 	*/
+#define CFG_LBC_LBCR		0x00000000
+#define CFG_LBC_LSRT		0x20000000
+#define CFG_LBC_MRTPR		0x20000000
+#define CFG_LBC_LSDMR_1		0x2861b723
+#define CFG_LBC_LSDMR_2		0x0861b723
+#define CFG_LBC_LSDMR_3		0x0861b723
+#define CFG_LBC_LSDMR_4		0x1861b723
+#define CFG_LBC_LSDMR_5		0x4061b723
+
+#define CONFIG_L1_INIT_RAM
+#define CFG_INIT_RAM_LOCK 	1
+#define CFG_INIT_RAM_ADDR       0x60000000      /* Initial RAM address  */
+#define CFG_INIT_RAM_END    	0x4000	    	/* End of used area in RAM */
+
+#define CFG_GBL_DATA_SIZE  	128		/* num bytes initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+#define CFG_MONITOR_LEN	    	(256 * 1024)    /* Reserve 256 kB for Mon */
+#define CFG_MALLOC_LEN	    	(128 * 1024)    /* Reserved for malloc */
+
+/* Serial Port */
+#define CONFIG_CONS_ON_SCC              	/* define if console on SCC */
+#undef  CONFIG_CONS_NONE                	/* define if console on something else */
+#define CONFIG_CONS_INDEX       2       	/* which serial channel for console */
+
+#define CONFIG_BAUDRATE	 	38400
+
+#define CFG_BAUDRATE_TABLE  \
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
+
+/* Use the HUSH parser */
+#define CFG_HUSH_PARSER
+#ifdef  CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+#endif
+
+/* I2C */
+#define  CONFIG_HARD_I2C    		/* I2C with hardware support*/
+#undef	CONFIG_SOFT_I2C			/* I2C bit-banged */
+#define CFG_I2C_SPEED		400000	/* I2C speed and slave address	*/
+#define CFG_I2C_SLAVE		0x7F
+#if 0
+#define CFG_I2C_NOPROBES        {0x00}  /* Don't probe these addrs */
+#else
+/* I did the 'if 0' so we could keep the syntax above if ever needed. */
+#undef CFG_I2C_NOPROBES
+#endif
+
+#define CFG_PCI_MEM_BASE	0xe0000000
+#define CFG_PCI_MEM_PHYS	0xe0000000
+#define CFG_PCI_MEM_SIZE	0x10000000
+
+#if defined(CONFIG_PCI) 		/* PCI Ethernet card */
+#define CONFIG_NET_MULTI
+#define CONFIG_EEPRO100
+#undef CONFIG_TULIP
+#define CONFIG_PCI_PNP	               	/* do pci plug-and-play */
+  #if !defined(CONFIG_PCI_PNP)
+  #define PCI_ENET0_IOADDR    	0xe0000000
+  #define PCI_ENET0_MEMADDR     0xe0000000
+  #define PCI_IDSEL_NUMBER      0x0c 	/* slot0->3(IDSEL)=12->15 */
+  #endif
+#define CONFIG_PCI_SCAN_SHOW    1       /* show pci devices on startup  */
+#define CFG_PCI_SUBSYS_VENDORID 0x1057  /* Motorola */
+#if defined(CONFIG_MPC85xx_REV1) 	/* Errata PCI 7 */
+  #define CFG_PCI_SUBSYS_DEVICEID 0x0003
+#else
+  #define CFG_PCI_SUBSYS_DEVICEID 0x0009
+#endif
+#elif defined(CONFIG_TSEC_ENET) 	/* TSEC Ethernet port */
+#define CONFIG_NET_MULTI 	1
+#define CONFIG_PHY_M88E1011      1       /* GigaBit Ether PHY        */
+#define CONFIG_MII		1	/* MII PHY management		*/
+#define CONFIG_PHY_ADDR		8	/* PHY address			*/
+#elif defined(CONFIG_ETHER_ON_FCC)	/* CPM FCC Ethernet */
+#define CONFIG_ETHER_ON_FCC2             /* define if ether on FCC   */
+#undef  CONFIG_ETHER_NONE               /* define if ether on something else */
+#define CONFIG_ETHER_INDEX      2       /* which channel for ether  */
+  #if (CONFIG_ETHER_INDEX == 2)
+  /*
+   * - Rx-CLK is CLK13
+   * - Tx-CLK is CLK14
+   * - Select bus for bd/buffers
+   * - Full duplex
+   */
+  #define CFG_CMXFCR_MASK       (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
+  #define CFG_CMXFCR_VALUE      (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
+  #define CFG_CPMFCR_RAMTYPE    0
+#if 0
+  #define CFG_FCC_PSMR          (FCC_PSMR_FDE)
+#else
+  #define CFG_FCC_PSMR          0
+#endif
+  #define FETH2_RST		0x01
+  #elif (CONFIG_ETHER_INDEX == 3)
+  /* need more definitions here for FE3 */
+  #define FETH3_RST		0x80
+  #endif  				/* CONFIG_ETHER_INDEX */
+#define CONFIG_MII			/* MII PHY management */
+#undef CONFIG_BITBANGMII		/* bit-bang MII PHY management	*/
+/*
+ * GPIO pins used for bit-banged MII communications
+ */
+#define MDIO_PORT	2		/* Port C */
+#define MDIO_ACTIVE	(iop->pdir |=  0x00400000)
+#define MDIO_TRISTATE	(iop->pdir &= ~0x00400000)
+#define MDIO_READ	((iop->pdat &  0x00400000) != 0)
+
+#define MDIO(bit)	if(bit) iop->pdat |=  0x00400000; \
+			else	iop->pdat &= ~0x00400000
+
+#define MDC(bit)	if(bit) iop->pdat |=  0x00200000; \
+			else	iop->pdat &= ~0x00200000
+
+#define MIIDELAY	udelay(1)
+#endif
+
+/* Environment */
+/* We use the top boot sector flash, so we have some 16K sectors for env
+ * But....functions don't seem smart enough yet.
+ */
+#ifndef CFG_RAMBOOT
+  #if defined(CONFIG_RAM_AS_FLASH)
+  #define CFG_ENV_IS_NOWHERE
+  #define CFG_ENV_ADDR		(CFG_FLASH_BASE + 0x100000)
+  #define CFG_ENV_SIZE		0x2000
+  #else
+  #define CFG_ENV_IS_IN_FLASH	1
+  #define CFG_ENV_ADDR		(CFG_MONITOR_BASE + 0x60000)
+  #define CFG_ENV_SECT_SIZE	0x4000	/* 16K (one top sector) for env */
+  #endif
+  #define CFG_ENV_SIZE		0x2000
+#else
+#define CFG_NO_FLASH		1	/* Flash is not usable now	*/
+#define CFG_ENV_IS_NOWHERE	1	/* Store ENV in memory only	*/
+#define CFG_ENV_ADDR		(CFG_MONITOR_BASE - 0x1000)
+#define CFG_ENV_SIZE		0x2000
+#endif
+
+#define CONFIG_BOOTARGS "root=/dev/nfs rw ip=any console=ttyS1,38400"
+#define CONFIG_BOOTCOMMAND	"bootm 0xff800000 0xff900000"
+#define CONFIG_BOOTDELAY	3	/* -1 disable autoboot */
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
+#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
+
+#if defined(CFG_RAMBOOT) || defined(CONFIG_RAM_AS_FLASH)
+  #if defined(CONFIG_PCI)
+  #define  CONFIG_COMMANDS	((CONFIG_CMD_DFL | CFG_CMD_PCI | \
+				CFG_CMD_PING | CFG_CMD_I2C) & \
+				 ~(CFG_CMD_ENV | \
+				  CFG_CMD_LOADS ))
+  #elif defined(CONFIG_TSEC_ENET)
+  #define  CONFIG_COMMANDS	((CONFIG_CMD_DFL | CFG_CMD_PING | \
+				CFG_CMD_MII | CFG_CMD_I2C ) & \
+				~(CFG_CMD_ENV))
+  #elif defined(CONFIG_ETHER_ON_FCC)
+  #define  CONFIG_COMMANDS	((CONFIG_CMD_DFL | CFG_CMD_MII | \
+				CFG_CMD_PING | CFG_CMD_I2C) & \
+				~(CFG_CMD_ENV))
+  #endif
+#else
+  #if defined(CONFIG_PCI)
+  #define  CONFIG_COMMANDS	(CONFIG_CMD_DFL | CFG_CMD_PCI | \
+				CFG_CMD_PING | CFG_CMD_I2C)
+  #elif defined(CONFIG_TSEC_ENET)
+  #define  CONFIG_COMMANDS	(CONFIG_CMD_DFL | CFG_CMD_PING | \
+				CFG_CMD_MII | CFG_CMD_I2C)
+  #elif defined(CONFIG_ETHER_ON_FCC)
+  #define  CONFIG_COMMANDS	(CONFIG_CMD_DFL | CFG_CMD_MII | \
+				CFG_CMD_PING | CFG_CMD_I2C)
+  #endif
+#endif
+#include <cmd_confdefs.h>
+
+#undef CONFIG_WATCHDOG			/* watchdog disabled		*/
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP			/* undef to save memory		*/
+#define CFG_PROMPT	"GPPP=> "	/* Monitor Command Prompt	*/
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#else
+#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS	16		/* max number of command args	*/
+#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+#define CFG_LOAD_ADDR	0x1000000	/* default load address */
+#define CFG_HZ		1000		/* decrementer freq: 1 ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ		(8 << 20) /* Initial Memory map for Linux */
+
+/* Cache Configuration */
+#define CFG_DCACHE_SIZE		32768
+#define CFG_CACHELINE_SIZE	32
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value */
+#endif
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM	0x02		/* Software reboot		*/
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
+#endif
+
+/*Note: change below for your network setting!!! */
+#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
+#define CONFIG_ETHADDR  00:01:af:07:9b:8a
+#define CONFIG_ETH1ADDR  00:01:af:07:9b:8b
+#define CONFIG_ETH2ADDR  00:01:af:07:9b:8c
+#endif
+
+#define CONFIG_SERVERIP 	192.168.85.1
+#define CONFIG_IPADDR  		192.168.85.60
+#define CONFIG_GATEWAYIP	192.168.85.1
+#define CONFIG_NETMASK		255.255.255.0
+#define CONFIG_HOSTNAME 	STX_GP3
+#define CONFIG_ROOTPATH 	/gppproot
+#define CONFIG_BOOTFILE 	uImage
+
+#endif	/* __CONFIG_H */

include/configs/suzaku.h

@@ -0,0 +1,90 @@
+/*
+ * (C) Copyright 2004 Atmark Techno, Inc.
+ *
+ * Yasushi SHOJI <yashi@atmark-techno.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * If we are developing, we might want to start armboot from ram
+ * so we MUST NOT initialize critical regs like mem-timing ...
+ */
+#define CONFIG_INIT_CRITICAL		/* undef for developing */
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_MICROBLZE	1	/* This is an MicroBlaze CPU	*/
+#define CONFIG_SUZAKU		1	/* on an SUZAKU Board		*/
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE		0x80000000
+#define CFG_SDRAM_SIZE		0x01000000
+#define CFG_FLASH_BASE		0xfff00000
+#define CFG_RESET_ADDRESS	0xfff00100
+#define CFG_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor */
+#define CFG_MONITOR_BASE        (CFG_SDRAM_BASE + CFG_SDRAM_SIZE - (1024 * 1024))
+#define CFG_MALLOC_LEN		(256 << 10)	/* Reserve 256 kB for malloc */
+
+#define CONFIG_BAUDRATE		115200
+#define CFG_BAUDRATE_TABLE	{ 115200 }
+
+#define CONFIG_COMMANDS		(CONFIG__CMD_DFL)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+#define CFG_UART1_BASE		(0xFFFF2000)
+#define CONFIG_SERIAL_BASE	CFG_UART1_BASE
+
+/*
+ * Miscellaneous configurable options
+ */
+#define	CFG_LONGHELP				/* undef to save memory		*/
+#define CFG_PROMPT		"SUZAKU> "	/* Monitor Command Prompt	*/
+#define CFG_CBSIZE		256
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size	*/
+#define CFG_MAXARGS		16		/* max number of command args	*/
+
+#define CFG_LOAD_ADDR		CFG_SDRAM_BASE	/* default load address		*/
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
+#define CFG_MAX_FLASH_SECT	1	/* max number of sectors on one chip	*/
+
+/*-----------------------------------------------------------------------
+ * NVRAM organization
+ */
+#define CFG_ENV_IS_NOWHERE	1
+#define	CFG_ENV_SIZE		0x10000	/* Total Size of Environment Sector	*/
+#define CFG_ENV_SECT_SIZE	0x10000	/* see README - env sector total size	*/
+
+#endif	/* __CONFIG_H */

include/fat.h

@@ -27,6 +27,8 @@
 #ifndef _FAT_H_
 #define _FAT_H_
 
+#include <asm/byteorder.h>
+
 #define CONFIG_SUPPORT_VFAT
 
 #define SECTOR_SIZE FS_BLOCK_SIZE
@@ -210,11 +212,4 @@ long file_fat_read(const char *filename, void *buffer, unsigned long maxsize);
 const char *file_getfsname(int idx);
 int fat_register_device(block_dev_desc_t *dev_desc, int part_no);
 
-#ifdef CONFIG_PXA250
-#undef FAT2CPU16
-#define FAT2CPU16(x) x
-#undef FAT2CPU32
-#define FAT2CPU32(x) x
-#endif
-
 #endif /* _FAT_H_ */

include/image.h

@@ -64,8 +64,9 @@
 #define IH_CPU_SH		9	/* SuperH	*/
 #define IH_CPU_SPARC		10	/* Sparc	*/
 #define IH_CPU_SPARC64		11	/* Sparc 64 Bit */
-#define	IH_CPU_M68K		12	/* M68K		*/
-#define	IH_CPU_NIOS		13	/* Nios-32	*/
+#define IH_CPU_M68K		12	/* M68K		*/
+#define IH_CPU_NIOS		13	/* Nios-32	*/
+#define IH_CPU_MICROBLAZE	14	/* MicroBlaze   */
 
 /*
  * Image Types

include/usb.h

@@ -12,7 +12,7 @@
  *
  * This program is distributed in the hope that it will be useful,
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
@@ -29,15 +29,15 @@
 #include <usb_defs.h>
 
 /* Everything is aribtrary */
-#define USB_ALTSETTINGALLOC          4
-#define USB_MAXALTSETTING	           128  /* Hard limit */
+#define USB_ALTSETTINGALLOC		4
+#define USB_MAXALTSETTING		128	/* Hard limit */
 
-#define USB_MAX_DEVICE              32
-#define USB_MAXCONFIG		            8
-#define USB_MAXINTERFACES	          8
-#define USB_MAXENDPOINTS	          16
-#define USB_MAXCHILDREN  						8 	/* This is arbitrary */
-#define USB_MAX_HUB									16
+#define USB_MAX_DEVICE			32
+#define USB_MAXCONFIG			8
+#define USB_MAXINTERFACES		8
+#define USB_MAXENDPOINTS		16
+#define USB_MAXCHILDREN			8	/* This is arbitrary */
+#define USB_MAX_HUB			16
 
 #define USB_CNTL_TIMEOUT 100 /* 100ms timeout */
 
@@ -125,19 +125,19 @@ struct usb_config_descriptor {
 	unsigned char  bmAttributes;
 	unsigned char  MaxPower;
 
-	unsigned char  no_of_if;			/* number of interfaces */
+	unsigned char  no_of_if;		/* number of interfaces */
 	struct usb_interface_descriptor if_desc[USB_MAXINTERFACES];
 } __attribute__ ((packed));
 
 
 struct usb_device {
-	int devnum;								/* Device number on USB bus */
-	int slow;									/* Slow device? */
-	char mf[32];		     			/* manufacturer */
-	char prod[32];		     		/* product */
-	char serial[32];       	  /* serial number */
+	int devnum;			/* Device number on USB bus */
+	int slow;			/* Slow device? */
+	char mf[32];			/* manufacturer */
+	char prod[32];			/* product */
+	char serial[32];		/* serial number */
 
-	int maxpacketsize;		    /* Maximum packet size; encoded as 0,1,2,3 = 8,16,32,64 */
+	int maxpacketsize;		/* Maximum packet size; encoded as 0,1,2,3 = 8,16,32,64 */
 	unsigned int toggle[2];		/* one bit for each endpoint ([0] = IN, [1] = OUT) */
 	unsigned int halted[2];		/* endpoint halts; one bit per endpoint # & direction; */
 			    /* [0] = IN, [1] = OUT */
@@ -152,7 +152,7 @@ struct usb_device {
 	int string_langid;		/* language ID for strings */
 	int (*irq_handle)(struct usb_device *dev);
 	unsigned long irq_status;
-	int irq_act_len;			/* transfered bytes */
+	int irq_act_len;		/* transfered bytes */
 	void *privptr;
 	/*
 	 * Child devices -  if this is a hub device
@@ -169,7 +169,7 @@ struct usb_device {
  * this is how the lowlevel part communicate with the outer world
  */
 
-#if defined(CONFIG_USB_UHCI) || defined(CONFIG_USB_OHCI)
+#if defined(CONFIG_USB_UHCI) || defined(CONFIG_USB_OHCI) || defined (CONFIG_USB_SL811HS)
 int usb_lowlevel_init(void);
 int usb_lowlevel_stop(void);
 int submit_bulk_msg(struct usb_device *dev, unsigned long pipe, void *buffer,int transfer_len);
@@ -180,7 +180,7 @@ int submit_int_msg(struct usb_device *dev, unsigned long pipe, void *buffer,
 
 /* Defines */
 #define USB_UHCI_VEND_ID 0x8086
-#define USB_UHCI_DEV_ID  0x7112
+#define USB_UHCI_DEV_ID	 0x7112
 
 #else
 #error USB Lowlevel not defined
@@ -242,8 +242,8 @@ int usb_set_interface(struct usb_device *dev, int interface, int alternate);
 	({ unsigned long x_ = (unsigned long)x; \
 	 (unsigned long)( \
 		((x_ & 0x000000FFUL) << 24) | \
-		((x_ & 0x0000FF00UL) <<  8) | \
-		((x_ & 0x00FF0000UL) >>  8) | \
+		((x_ & 0x0000FF00UL) <<	 8) | \
+		((x_ & 0x00FF0000UL) >>	 8) | \
 		((x_ & 0xFF000000UL) >> 24) ); \
 	})
 #endif /* LITTLEENDIAN */
@@ -298,7 +298,7 @@ int usb_set_interface(struct usb_device *dev, int interface, int alternate);
 
 /* The D0/D1 toggle bits */
 #define usb_gettoggle(dev, ep, out) (((dev)->toggle[out] >> ep) & 1)
-#define	usb_dotoggle(dev, ep, out)  ((dev)->toggle[out] ^= (1 << ep))
+#define usb_dotoggle(dev, ep, out)  ((dev)->toggle[out] ^= (1 << ep))
 #define usb_settoggle(dev, ep, out, bit) ((dev)->toggle[out] = ((dev)->toggle[out] & ~(1 << ep)) | ((bit) << ep))
 
 /* Endpoint halt control/status */

lib_arm/armlinux.c

@@ -340,7 +340,7 @@ static void setup_initrd_tag (bd_t *bd, ulong initrd_start, ulong initrd_end)
 	/* an ATAG_INITRD node tells the kernel where the compressed
 	 * ramdisk can be found. ATAG_RDIMG is a better name, actually.
 	 */
-	params->hdr.tag = ATAG_INITRD;
+	params->hdr.tag = ATAG_INITRD2;
 	params->hdr.size = tag_size (tag_initrd);
 
 	params->u.initrd.start = initrd_start;

lib_microblaze/Makefile

@@ -0,0 +1,44 @@
+#
+# (C) Copyright 2003-2004
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(ARCH).a
+
+AOBJS	=
+
+COBJS	= board.o microblaze_linux.o time.o
+
+OBJS	= $(AOBJS) $(COBJS)
+
+$(LIB):	.depend $(OBJS)
+	$(AR) crv $@ $(OBJS)
+
+#########################################################################
+
+.depend:	Makefile $(AOBJS:.o=.S) $(COBJS:.o=.c)
+		$(CC) -M $(CFLAGS) $(AOBJS:.o=.S) $(COBJS:.o=.c) > $@
+
+sinclude .depend
+
+#########################################################################

lib_microblaze/board.c

@@ -0,0 +1,95 @@
+/*
+ * (C) Copyright 2004 Atmark Techno, Inc.
+ *
+ * Yasushi SHOJI <yashi@atmark-techno.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <malloc.h>
+#include <version.h>
+#include <watchdog.h>
+
+const char version_string[] =
+	U_BOOT_VERSION" (" __DATE__ " - " __TIME__ ")";
+
+/*
+ * Begin and End of memory area for malloc(), and current "brk"
+ */
+static ulong mem_malloc_start;
+static ulong mem_malloc_end;
+static ulong mem_malloc_brk;
+
+
+void *sbrk (ptrdiff_t increment)
+{
+	ulong old = mem_malloc_brk;
+	ulong new = old + increment;
+
+	if ((new < mem_malloc_start) || (new > mem_malloc_end)) {
+		return (NULL);
+	}
+	mem_malloc_brk = new;
+	return ((void *) old);
+}
+
+/*
+ * All attempts to come up with a "common" initialization sequence
+ * that works for all boards and architectures failed: some of the
+ * requirements are just _too_ different. To get rid of the resulting
+ * mess of board dependend #ifdef'ed code we now make the whole
+ * initialization sequence configurable to the user.
+ *
+ * The requirements for any new initalization function is simple: it
+ * receives a pointer to the "global data" structure as it's only
+ * argument, and returns an integer return code, where 0 means
+ * "continue" and != 0 means "fatal error, hang the system".
+ */
+typedef int (init_fnc_t) (void);
+
+init_fnc_t *init_sequence[] = {
+	serial_init,		/* serial communications setup */
+	NULL,
+};
+
+void board_init(void)
+{
+	init_fnc_t **init_fnc_ptr;
+
+	for (init_fnc_ptr = init_sequence; *init_fnc_ptr; ++init_fnc_ptr) {
+		WATCHDOG_RESET ();
+		if ((*init_fnc_ptr) () != 0) {
+			hang ();
+		}
+	}
+
+	/* main_loop */
+	for (;;) {
+		WATCHDOG_RESET ();
+		main_loop ();
+	}
+}
+
+void hang (void)
+{
+	puts ("### ERROR ### Please RESET the board ###\n");
+	for (;;);
+}

lib_microblaze/microblaze_linux.c

@@ -0,0 +1,31 @@
+/*
+ * (C) Copyright 2004 Atmark Techno, Inc.
+ *
+ * Yasushi SHOJI <yashi@atmark-techno.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+
+void do_bootm_linux(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[],
+		ulong addr, ulong *len_ptr, int   verify)
+{
+}

lib_microblaze/time.c

@@ -0,0 +1,27 @@
+/*
+ * (C) Copyright 2004 Atmark Techno, Inc.
+ *
+ * Yasushi SHOJI <yashi@atmark-techno.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+void udelay(unsigned long usec)
+{
+}

lib_ppc/board.c

@@ -510,27 +510,6 @@ void board_init_f (ulong bootflag)
 #if defined(CONFIG_405GP) || defined(CONFIG_405EP)
 	bd->bi_pci_busfreq = get_PCI_freq ();
 	bd->bi_opbfreq = get_OPB_freq ();
-
-#if defined(CONFIG_I2CFAST)
-	/*
-	 * set bi_iic_fast for linux taking environment variable
-	 * "i2cfast" into account
-	 */
-	{
-		char *s = getenv ("i2cfast");
-		if (s && ((*s == 'y') || (*s == 'Y'))) {
-			bd->bi_iic_fast[0] = 1;
-			bd->bi_iic_fast[1] = 1;
-		} else {
-			bd->bi_iic_fast[0] = 0;
-			bd->bi_iic_fast[1] = 0;
-		}
-	}
-#else
-	bd->bi_iic_fast[0] = 0;
-	bd->bi_iic_fast[1] = 0;
-#endif
-
 #elif defined(CONFIG_XILINX_ML300)
 	bd->bi_pci_busfreq = get_PCI_freq ();
 #endif
@@ -743,6 +722,31 @@ void board_init_r (gd_t *id, ulong dest_addr)
 	 * where had to use getenv_r(), which can be pretty slow when
 	 * the environment is in EEPROM.
 	 */
+
+#if defined(CFG_EXTBDINFO)
+#if defined(CONFIG_405GP) || defined(CONFIG_405EP)
+#if defined(CONFIG_I2CFAST)
+	/*
+	 * set bi_iic_fast for linux taking environment variable
+	 * "i2cfast" into account
+	 */
+	{
+		char *s = getenv ("i2cfast");
+		if (s && ((*s == 'y') || (*s == 'Y'))) {
+			bd->bi_iic_fast[0] = 1;
+			bd->bi_iic_fast[1] = 1;
+		} else {
+			bd->bi_iic_fast[0] = 0;
+			bd->bi_iic_fast[1] = 0;
+		}
+	}
+#else
+	bd->bi_iic_fast[0] = 0;
+	bd->bi_iic_fast[1] = 0;
+#endif	/* CONFIG_I2CFAST */
+#endif	/* CONFIG_405GP, CONFIG_405EP */
+#endif	/* CFG_EXTBDINFO */
+
 	s = getenv ("ethaddr");
 #if defined (CONFIG_MBX) || defined (CONFIG_RPXCLASSIC) || defined(CONFIG_IAD210)
 	if (s == NULL)
@@ -867,6 +871,7 @@ void board_init_r (gd_t *id, ulong dest_addr)
     defined(CONFIG_MPC8560ADS)	|| \
     defined(CONFIG_PCU_E)	|| \
     defined(CONFIG_RPXSUPER)	|| \
+    defined(CONFIG_STXGP3)	|| \
     defined(CONFIG_SPD823TS)	)
 
 	WATCHDOG_RESET ();

microblaze_config.mk

@@ -0,0 +1,35 @@
+#
+# (C) Copyright 2004 Atmark Techno, Inc.
+#
+# Yasushi SHOJI <yashi@atmark-techno.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+ifdef CONFIG_MICROBLAZE_HARD_MULT
+PLATFORM_CPPFLAGS += -mno-xl-soft-mul
+endif
+
+ifdef CONFIG_MICROBLAZE_HARD_DIV
+PLATFORM_CPPFLAGS += -mno-xl-soft-div
+endif
+
+ifdef CONFIG_MICROBLAZE_HARD_BARREL
+PLATFORM_CPPFLAGS += -mxl-barrel-shift
+endif

net/eth.c

@@ -48,6 +48,7 @@ extern int plb2800_eth_initialize(bd_t*);
 extern int ppc_4xx_eth_initialize(bd_t *);
 extern int ppc_440x_eth_initialize(bd_t *);
 extern int rtl8139_initialize(bd_t*);
+extern int rtl8169_initialize(bd_t*);
 extern int scc_initialize(bd_t*);
 extern int skge_initialize(bd_t*);
 extern int tsec_initialize(bd_t*);
@@ -178,6 +179,9 @@ int eth_initialize(bd_t *bis)
 #if defined(CONFIG_RTL8139)
 	rtl8139_initialize(bis);
 #endif
+#if defined(CONFIG_RTL8169)
+	rtl8169_initialize(bis);
+#endif
 
 	if (!eth_devices) {
 		puts ("No ethernet found.\n");