Code cleanup; make several boards compile & link.

* Patches by Travis Sawyer, 12 Mar 2004:
- Fix Gigabit Ethernet support for 440GX - Add Gigabit Ethernet Support to MII PHY utilities * Patch by Brad Kemp, 12 Mar 2004: Fixes for drivers/cfi_flash.c: - Better support for x8/x16 implementations - Added failure for AMD chips attempting to use CFG_FLASH_USE_BUFFER_WRITE - Added defines for AMD command and address constants * Patch by Leon Kukovec, 12 Mar 2004: Fix get_dentfromdir() to correctly handle deleted dentries * Patch by George G. Davis, 11 Mar 2004: Remove hard coded network settings in TI OMAP1610 H2 default board config * Patch by George G. Davis, 11 Mar 2004: add support for ADS GraphicsClient+ board.
2026-06-12 14:47:22 +03:00 · 2004-03-14 22:25:36 +00:00 · 2004-03-14 18:23:55 +00:00 · 2004-03-14 16:51:43 +00:00 · 2004-03-14 15:20:55 +00:00 · 2004-03-14 15:06:13 +00:00
348 changed files with 48313 additions and 3872 deletions
--- a/294
+++ b/294
@@ -2,6 +2,300 @@
 Changes for U-Boot 1.0.2:
 ======================================================================

+* Patches by Travis Sawyer, 12 Mar 2004:
+  - Fix Gigabit Ethernet support for 440GX
+  - Add Gigabit Ethernet Support to MII PHY utilities
+
+* Patch by Brad Kemp, 12 Mar 2004:
+  Fixes for drivers/cfi_flash.c:
+  - Better support for x8/x16 implementations
+  - Added failure for AMD chips attempting to use CFG_FLASH_USE_BUFFER_WRITE
+  - Added defines for AMD command and address constants
+
+* Patch by Leon Kukovec, 12 Mar 2004:
+  Fix get_dentfromdir() to correctly handle deleted dentries
+
+* Patch by George G. Davis, 11 Mar 2004:
+  Remove hard coded network settings in TI OMAP1610 H2
+  default board config
+
+* Patch by George G. Davis, 11 Mar 2004:
+  add support for ADS GraphicsClient+ board.
+
+* Patch by  Pierre Aubert, 11 Mar 2004:
+  - add bitmap command and splash screen support in cfb console
+  - add [optional] origin in the bitmap display command
+
+* Patch by Travis Sawyer, 11 Mar 2004:
+  Fix ocotea board early init interrupt setup.
+
+* Patch by Thomas Viehweger, 11 Mar 2004:
+  Remove redundand code; add  PCI-specific bits to include/mpc8260.h
+
+* Patch by Stephan Linz, 09 Mar 2004
+  - Add support for the SSV ADNP/ESC1 (Nios Softcore)
+
+* Patch by George G. Davis, 9 Mar 2004:
+  fix recent build failure for SA1100 target
+
+* Patch by Travis Sawyer, 09 Mar 2004:
+  Support native interrupt mode for the IBM440GX.
+  Previously it was running in 440GP compatibility mode.
+
+* Patch by Philippe Robin, 09 Mar 2004:
+  Added ARM Integrator AP, CP and Versatile PB926EJ-S Reference
+  Platform support.
+
+* Patch by Masami Komiya, 08 Mar 2004:
+  Don't overwrite server IP address or boot file name
+  when the boot server does not return values
+
+* Patch by listmember@orkun.us, 5 Mar 2004:
+  Removed compile time restriction on CFG_I2C_SPEED for DS1338 RTC
+
+* Patch by Tolunay Orkun, 5 Mar 2004:
+  Fix early board initialization for Cogent CSB272 board
+
+* Patch by Ed Okerson, 3 Mar 2004:
+  fix CFI flash writes for little endian systems
+
+* Patch by Reinhard Meyer, 01 Mar 2004:
+  generalize USB and IDE support for MPC5200 with according
+  changes to IceCube.h and TOP5200.h
+  add Am29LV256 256 MBit FLASH support for TOP5200 boards
+  add info about USB and IDE to README
+
+* Patch by Yuli Barcohen, 4 Mar 2004:
+  Fix problems with GCC 3.3.x which changed handling of global
+  variables explicitly initialized to zero (now in .bss instead of
+  .data as before).
+
+* Patch by Leon Kukovec, 02 Mar 2004:
+  add strswab() to fix IDE LBA capacity, firmware and model numbers
+  on little endian machines
+
+* Patch by Masami Komiya, 02 Mar 2004:
+  - Remove get_ticks() from NFS code
+  - Add verification of RPC transaction ID
+
+* Patch by Pierre Aubert, 02 Mar 2004:
+  cleanup for IDE and USB drivers for MPC5200
+
+* Patch by Travis Sawyer, 01 Mar 2004:
+  Ocotea:
+  - Add IBM PPC440GX Ref Platform support (Ocotea)
+    Original code by Paul Reynolds <PaulReynolds@lhsolutions.com>
+    Adapted to U-Boot and 440GX port
+  440gx_enet.c:
+  - Add gracious handling of all Ethernet Pin Selections for 440GX
+  - Add RGMII selection for Cicada CIS8201 Gigabit PHY
+  ppc440.h:
+  - Add needed bit definitions
+  - Fix formatting
+
+* Patch by Carl Riechers, 1 Mar 2004:
+  Add PPC440GX prbdv0 divider to fix memory clock calculation.
+
+* Patch by Stephan Linz, 27 Feb 2004
+  - avoid problems for targets without NFS download support
+
+* Patch by Rune Torgersen, 27 Feb 2004:
+  - Added LBA48 support (CONFIG_LBA48 & CFG_64BIT_LBA)
+  - Added support for 64bit printing in vsprintf (CFG_64BIT_VSPRINTF)
+  - Added support for 64bit strtoul (CFG_64BIT_STRTOUL)
+
+* Patch by Masami Komiya, 27 Feb 2004:
+  Fix rarpboot: add autoload by NFS
+
+* Patch by Dan Eisenhut, 26 Feb 2004:
+  fix flash_write return value in saveenv
+
+* Patch by Stephan Linz, 11 Dec 2003
+  expand config.mk to avoid trigraph warnings on NIOS
+
+* Rename "BMS2003" board into "HMI10"
+
+* SX1 patches: use "serial#" for USB serial #; use redundand environment
+  storage; auto-set console on USB port (using preboot command)
+
+* Add support for SX1 mobile phone; add support for USB-based console
+  (enable with "setenv stdout usbtty; setenv stdin usbtty")
+
+* Fix LOWBOOT configuration for MPC5200 with DDR memory
+
+* Fix SDRAM timings for LITE5200 / IceCube board
+
+* Handle Auti-MDIX / connection status for INCA-IP
+
+* Fix USB problems when attempting to read 0 bytes
+
+* Patch by Travis Sawyer, 26 Feb 2004:
+  Fix broken compile for XPEDITE1K target.
+
+* Patch by Stephan Linz, 26 Feb 2004:
+  Bug fix for NFS code on NIOS targets
+
+* Patch by Stephen Williams, 26 Feb 2004:
+  Break up SystemACE reads of large block counts
+
+* Patch by Pierre Aubert, 26 Feb 2004
+  add IDE support for MPC5200
+
+* Patch by Masami Komiya, 26 Feb 2004:
+  add autoload via NFS
+
+* Patch by Stephen Williams
+  Use of CONFIG_SERIAL_SOFTWARE_FIFO in board.c consistent with uses
+  elsewhere in the source.
+
+* Patch by Steven Scholz, 25 Feb 2004:
+  - Timeouts in FPGA code should be based on CFG_HZ
+  - Minor cleanup in code for Altera FPGA ACEX1K
+
+* Patch by Steven Scholz, 25 Feb 2004:
+  Changed "Directory Hierarchy" section in README
+
+* Patch by Masami Komiya, 25 Feb 2004:
+  Reduce copy count in nfs_read_reply() of NFS code
+
+* Patch by Markus Pietrek, 24 Feb 2004:
+  NS9750 DevBoard added
+
+* Patch by Pierre Aubert, 24 Feb 2004
+  add USB support for MPC5200
+
+* Patch by Steven Scholz, 24 Feb 2004:
+  - fix MII commands to use values from last command
+
+* Patch by Torsten Demke, 24 Feb 2004:
+  Add support for the eXalion platform (SPSW-8240, F-30, F-300)
+
+* Patch by Rahul Shanbhag, 19 Feb 2004:
+  Fixes for for OMAP1610 board:
+  - shift some IRQ specific code to platform.S file
+  - remove duplicatewatchdog reset code from start.S
+
+* Make Auto-MDIX Support configurable on INCA-IP board
+
+* Fix license for mkimage tool
+
+* Patch by Masami Komiya, 24 Feb 2004:
+  Update NetBootFileXferSize in NFS code
+
+* Patch by Scott McNutt, 24 Feb 2004:
+  fix packet length in NFS code
+
+* Patch by Masami Komiy, 22 Feb 2004:
+  Add support for NFS for file download
+
+* Patch by Andrea Scian, 17 Feb 2004:
+  Add support for S3C44B0 processor and DAVE B2 board
+
+* Patch by Steven Scholz, 20 Feb 2004:
+  - Add support for MII commands on AT91RM9200 boards
+  - some cleanup in AT91RM9200 ethernet code
+
+* Patch by Peter Ryser, 20 Feb 2004:
+  Add support for the Xilinx ML300 platform
+
+* Patch by Stephan Linz, 17 Feb 2004:
+  Fix watchdog support for NIOS
+
+* Patch by Josh Fryman, 16 Feb 2004:
+  Fix byte-swapping for cfi_flash.c for different bus widths
+
+* Patch by Jon Diekema, 14 Jeb 2004:
+  Remove duplicate "FPGA Support" notes from the README file
+
+* Patches by Reinhard Meyer, 14 Feb 2004:
+  - update board/emk tree; use common flash driver
+  - Corrected tested bits in machine check exception in cpu/mpc5xxx/traps.c
+    [adapted for other PPC CPUs -- wd]
+  - Added support for the M48T08 on the EVAL5200 board in rtc/mk48t59.c
+
+* Patch by Jon Diekema, 13 Feb 2004:
+  Call show_boot_progress() whenever POST "FAILED" is printed.
+
+* Patch by Nishant Kamat, 13 Feb 2004:
+  Add support for TI OMAP1610 H2 Board
+  Fixes for cpu/arm926ejs/interrupt.c
+	(based on Richard Woodruff's patch for arm925, 16 Oct 03)
+  Fix for a timer bug in OMAP1610 Innovator
+  Add support for CS0 (ROM)/CS3 (Flash) boot in OMAP1610 Innovator and H2
+
+* Patches by Stephan Linz, 12 Feb 2004:
+  - add support for NIOS timer with variable period preload counter value
+  - prepare POST framework support for NIOS targets
+
+* Patch by Denis Peter, 11 Feb 2004:
+  add POST support for the MIP405 board
+
+* Patch by Laurent Mohin, 10 Feb 2004:
+  Fix buffer overflow in common/usb.c
+
+* Patch by Tolunay Orkun, 10 Feb 2004:
+  Add support for Cogent CSB272 board
+
+* Patch by Thomas Elste, 10 Feb 2004:
+  Add support for NET+50 CPU and ModNET50 board
+
+* Patch by Sam Song, 10 Feb 2004:
+  Fix typos in cfi_flash.c
+
+* Patch by Leon Kukovec, 10 Feb 2004
+  Fixed long dir entry slot id calculation in get_vfatname
+
+* Patch by Robin Gilks, 10 Feb 2004:
+  add "itest" command (operators: -eq, -ne, -lt, -gt, -le, -ge, ==,
+  !=, <>, <, >, <=, >=)
+
+* Fix problem with side effects in macros in include/usb.h
+
+* Patch by David Benson, 13 Nov 2003:
+  bug 841358 - fix TFTP download size limit
+
+* Fixing bug 850768:
+  improper flush_cache() in load_serial()
+
+* Fixing bug 834943:
+  MPC8540 - missing volatile declarations
+
+* Patch by Stephen Williams, 09 Feb 2004:
+  Add support for Xilinx SystemACE chip:
+  - New files common/cmd_ace.c and include/systemace.h
+  - Hook systemace support into cmd_fat and the partition manager
+
+* Patch by Travis Sawyer, 09 Feb 2004:
+  Add bi_opbfreq & bi_iic_fast to 440GX bd_info as needed for Linux
+
+* Patch by Travis Sawyer, 09 Feb 2004:
+  o 440GX:
+    - Fix PCI Indirect access for type 1 config cycles with ppc440.
+    - Add phymode for 440 enet
+    - fix pci pre init
+  o XPedite1K:
+    - Change board_pre_init to board_early_init_f
+    - Add user flash to bus controller setup
+    - Fix pci pre init
+    - Fix is_pci_host to check GPIO for monarch bit
+    - Force xpedite1k to pci conventional mode (via #define option)
+
+* Patch by Brad Kemp, 4 Feb 2004:
+  - handle the machine check that is generated during the PCI scans
+    on 82xx processors.
+  - define the registers used in the IMMR by the PCI subsystem.
+
+* Patch by Pierre Aubert, 03 Feb 2004:
+  cpu/mpc5xxx/start.S: copy MBAR into SPR311
+
+* Patch by Jeff Angielski, 03 Feb 2004:
+  Fix copy & paste error in cpu/mpc8260/pci.c
+
+* Patch by Reinhard Meyer, 24 Jan 2004:
+  Fix typo in cpu/mpc5xxx/pci_mpc5200.c
+
+* Add Auto-MDIX support for INCA-IP
+
 * Some code cleanup

 * Patch by Josef Baumgartner, 10 Feb 2004:
--- a/6
+++ b/6
@@ -103,6 +103,11 @@ N: Dave Ellis
 E: DGE@sixnetio.com
 D: EEPROM Speedup, SXNI855T port

+N: Thomas Elste
+E: info@elste.org
+D: Port for the ModNET50 Board, NET+50 CPU Port
+W: http://www.imms.de
+
 N: Daniel Engström
 E: daniel@omicron.se
 D: x86 port, Support for sc520_cdp board
@@ -211,6 +216,7 @@ W: http://www.leox.org
 N: Stephan Linz
 E: linz@li-pro.net
 D: Support for Nios Stratix Development Kit (DK-1S10)
+D: Support for SSV ADNP/ESC1 (Nios Cyclone)
 W: http://www.li-pro.net

 N: Raymond Lo
--- a/17
+++ b/17
@@ -49,6 +49,10 @@ K

 	FLAGADM			MPC823

+Torsten Demke <torsten.demke@fci.com>
+
+	eXalion			MPC824x
+
 Wolfgang Denk <wd@denx.de>

 	AMX860			MPC860
@@ -187,6 +191,9 @@ Scott McNutt <smcnutt@artesyncp.com>

 	EBONY			PPC440GP

+Tolunay Orkun <torkun@nextio.com>
+	csb272			PPC4xx
+
 Keith Outwater <Keith_Outwater@mvis.com>

 	GEN860T			MPC860T
@@ -286,6 +293,10 @@ Unknown / orphaned boards:
 #	Board			CPU					#
 #########################################################################

+Thomas Elste <info@elste.org>
+
+	modnet50		ARM720T (NET+50)
+
 Peter Figuli <peposh@etc.sk>

 	wepep250		xscale
@@ -307,9 +318,14 @@ Gary Jennejohn <gj@denx.de>
 	trab			ARM920T

 Kshitij Gupta <kshitij@ti.com>
+
 	omap1510inn		ARM925T
 	omap1610inn		ARM926EJS

+Nishant Kamat <nskamat@ti.com>
+
+	omap1610h2		ARM926EJS
+
 David Müller <d.mueller@elsoft.ch>

 	smdk2410		ARM920T
@@ -365,6 +381,7 @@ Thomas Lange <thomas@corelatus.se>
 Stephan Linz <linz@li-pro.net>

 	DK1S10			Nios-32
+	ADNPESC1		Nios-32

 Scott McNutt <smcnutt@psyent.com>

--- a/39
+++ b/39
@@ -40,7 +40,7 @@ LIST_8xx="	\
 	GEN860T_SC	GENIETV		GTH		hermes		\
 	IAD210		ICU862_100MHz	IP860		IVML24		\
 	IVML24_128	IVML24_256	IVMS8		IVMS8_128	\
-	IVMS8_256	KUP4K           LANTEC	        lwmon   	\
+	IVMS8_256	KUP4K		LANTEC		lwmon		\
 	MBX		MBX860T		MHPC		MPC86xADS	\
 	MVS1		NETVIA		NETVIA_V2	NX823		\
 	pcu_e		QS823		QS850		QS860T		\
@@ -56,15 +56,15 @@ LIST_8xx="	\
 #########################################################################

 LIST_4xx="	\
-	ADCIOP		AR405		ASH405          BUBINGA405EP    \
-	CANBT		CPCI405		CPCI4052 	CPCI405AB       \
-	CPCI440         CPCIISER4	CRAYL1  	DASA_SIM	\
-	DP405           DU405    	EBONY           ERIC  		\
-	EXBITGEN	HUB405          MIP405  	MIP405T		\
-	ML2		OCRTC		ORSG		PCI405		\
-	PIP405		PLU405          PMC405          PPChameleonEVB	\
-	VOH405          W7OLMC		W7OLMG          WALNUT405	\
-	XPEDITE1K							\
+	ADCIOP		AR405		ASH405		BUBINGA405EP	\
+	CANBT		CPCI405		CPCI4052	CPCI405AB	\
+	CPCI440		CPCIISER4	CRAYL1		csb272		\
+	DASA_SIM	DP405		DU405		EBONY		\
+	ERIC		EXBITGEN	HUB405		MIP405		\
+	MIP405T		ML2		ml300		OCOTEA		\
+	OCRTC		ORSG		PCI405		PIP405		\
+	PLU405		PMC405		PPChameleonEVB	VOH405		\
+	W7OLMC		W7OLMG		WALNUT405	XPEDITE1K	\
 "

 #########################################################################
@@ -72,10 +72,10 @@ LIST_4xx="	\
 #########################################################################

 LIST_824x="	\
-	A3000           BMW		CPC45		CU824		\
-	debris		MOUSSE          MUSENKI    	MVBLUE		\
-	OXC		PN62		Sandpoint8240   Sandpoint8245	\
-	SL8245		utx8245						\
+	A3000		BMW		CPC45		CU824		\
+	debris		eXalion		MOUSSE		MUSENKI		\
+	MVBLUE		OXC		PN62		Sandpoint8240	\
+	Sandpoint8245	SL8245		utx8245				\
 "

 #########################################################################
@@ -122,22 +122,23 @@ LIST_ppc="${LIST_5xx}  ${LIST_5xxx} \
 ## StrongARM Systems
 #########################################################################

-LIST_SA="dnp1110 lart shannon"
+LIST_SA="dnp1110 gcplus lart shannon"

 #########################################################################
 ## ARM7 Systems
 #########################################################################

-LIST_ARM7="ep7312 impa7"
+LIST_ARM7="B2 ep7312 impa7"

 #########################################################################
 ## ARM9 Systems
 #########################################################################

 LIST_ARM9="	\
-	at91rm9200dk	omap1510inn	omap1610inn			\
+	at91rm9200dk	integratorcp	integratorap			\
+	omap1510inn	omap1610h2	omap1610inn			\
 	smdk2400	smdk2410	trab				\
-	VCMA9								\
+	VCMA9		versatile					\
 "

 #########################################################################
@@ -176,6 +177,8 @@ LIST_x86="${LIST_I486}"
 #########################################################################

 LIST_nios="	\
+	ADNPESC1 ADNPESC1_base_32					\
+	ADNPESC1_DNPEVA2_base_32					\
 	DK1C20 DK1C20_standard_32					\
 	DK1S10 DK1S10_standard_32 DK1S10_mtx_ldk_20			\
 "
--- a/92
+++ b/92
@@ -111,7 +111,8 @@ LIBS += common/libcommon.a
 .PHONY : $(LIBS)

 # Add GCC lib
-PLATFORM_LIBS += -L $(shell dirname `$(CC) $(CFLAGS) -print-libgcc-file-name`) -lgcc
+PLATFORM_LIBS += --no-warn-mismatch -L $(shell dirname `$(CC) $(CFLAGS) -print-libgcc-file-name`) -lgcc
+

 # The "tools" are needed early, so put this first
 # Don't include stuff already done in $(LIBS)
@@ -207,9 +208,10 @@ PATI_config:unconfig
 MPC5200LITE_config		\
 MPC5200LITE_LOWBOOT_config	\
 MPC5200LITE_LOWBOOT08_config	\
-icecube_5200_DDR_LOWBOOT_config	\
 icecube_5200_DDR_config		\
 IceCube_5200_DDR_config		\
+icecube_5200_DDR_LOWBOOT_config \
+icecube_5200_DDR_LOWBOOT08_config \
 icecube_5200_config		\
 IceCube_5200_config		\
 IceCube_5100_config:		unconfig
@@ -260,9 +262,6 @@ FADS860T_config:	unconfig
 AMX860_config	:	unconfig
 	@./mkconfig $(@:_config=) ppc mpc8xx amx860 westel

-bms2003_config	:	unconfig
-	@./mkconfig $(@:_config=) ppc mpc8xx tqm8xx
-
 c2mon_config:		unconfig
 	@./mkconfig $(@:_config=) ppc mpc8xx c2mon

@@ -304,6 +303,9 @@ GTH_config:	unconfig
 hermes_config	:	unconfig
 	@./mkconfig $(@:_config=) ppc mpc8xx hermes

+HMI10_config	:	unconfig
+	@./mkconfig $(@:_config=) ppc mpc8xx tqm8xx
+
 IAD210_config: unconfig
 	@./mkconfig $(@:_config=) ppc mpc8xx IAD210 siemens

@@ -558,6 +560,9 @@ CPCIISER4_config:	unconfig
 CRAYL1_config:unconfig
 	@./mkconfig $(@:_config=) ppc ppc4xx L1 cray

+csb272_config:	unconfig
+	@./mkconfig $(@:_config=) ppc ppc4xx csb272
+
 DASA_SIM_config: unconfig
 	@./mkconfig $(@:_config=) ppc ppc4xx dasa_sim esd

@@ -590,6 +595,12 @@ MIP405T_config:unconfig
 ML2_config:unconfig
 	@./mkconfig $(@:_config=) ppc ppc4xx ml2

+ml300_config:unconfig
+	@./mkconfig $(@:_config=) ppc ppc4xx ml300 xilinx
+
+OCOTEA_config:unconfig
+	@./mkconfig $(@:_config=) ppc ppc4xx ocotea
+
 OCRTC_config		\
 ORSG_config:	unconfig
 	@./mkconfig $(@:_config=) ppc ppc4xx ocrtc esd
@@ -665,6 +676,9 @@ CPC45_ROMBOOT_config:	unconfig
 CU824_config: unconfig
 	@./mkconfig $(@:_config=) ppc mpc824x cu824

+eXalion_config: unconfig
+	@./mkconfig $(@:_config=) ppc mpc824x eXalion
+
 MOUSSE_config: unconfig
 	@./mkconfig $(@:_config=) ppc mpc824x mousse

@@ -894,12 +908,15 @@ ZUMA_config:	unconfig
 at91rm9200dk_config	:	unconfig
 	@./mkconfig $(@:_config=) arm at91rm9200 at91rm9200dk

-lart_config	:	unconfig
-	@./mkconfig $(@:_config=) arm sa1100 lart
-
 dnp1110_config	:	unconfig
 	@./mkconfig $(@:_config=) arm sa1100 dnp1110

+gcplus_config	:	unconfig
+	@./mkconfig $(@:_config=) arm sa1100 gcplus
+
+lart_config	:	unconfig
+	@./mkconfig $(@:_config=) arm sa1100 lart
+
 shannon_config	:	unconfig
 	@./mkconfig $(@:_config=) arm sa1100 shannon

@@ -909,11 +926,37 @@ shannon_config	:	unconfig

 xtract_trab = $(subst _bigram,,$(subst _bigflash,,$(subst _old,,$(subst _config,,$1))))

+xtract_omap1610xxx = $(subst _cs0boot,,$(subst _cs3boot,, $(subst _config,,$1)))
+
+SX1_config :		unconfig
+	@./mkconfig $(@:_config=) arm arm925t sx1
+
+integratorcp_config :	unconfig
+	@./mkconfig $(@:_config=) arm arm926ejs integratorcp
+
+integratorap_config :	unconfig
+	@./mkconfig $(@:_config=) arm arm926ejs integratorap
+
+versatile_config :	unconfig
+	@./mkconfig $(@:_config=) arm arm926ejs versatile
+
 omap1510inn_config :	unconfig
 	@./mkconfig $(@:_config=) arm arm925t omap1510inn

-omap1610inn_config :	unconfig
-	@./mkconfig $(@:_config=) arm arm926ejs omap1610inn
+omap1610inn_config \
+omap1610inn_cs0boot_config \
+omap1610inn_cs3boot_config \
+omap1610h2_config \
+omap1610h2_cs0boot_config \
+omap1610h2_cs3boot_config :	unconfig
+	@if [ "$(findstring _cs0boot_, $@)" ] ; then \
+		echo "#define CONFIG_CS0_BOOT" >> ./include/config.h ; \
+		echo "Configured for CS0 boot"; \
+	else \
+		echo "#define CONFIG_CS3_BOOT" >> ./include/config.h ; \
+		echo "Configured for CS3 boot"; \
+	fi;
+	@./mkconfig -a $(call xtract_omap1610xxx,$@) arm arm926ejs omap1610inn

 smdk2400_config	:	unconfig
 	@./mkconfig $(@:_config=) arm arm920t smdk2400
@@ -949,6 +992,14 @@ trab_old_config:	unconfig
 VCMA9_config	:	unconfig
 	@./mkconfig $(@:_config=) arm arm920t vcma9 mpl

+
+#########################################################################
+## S3C44B0 Systems
+#########################################################################
+
+B2_config	:	unconfig
+	@./mkconfig $(@:_config=) arm s3c44b0 B2 dave
+
 #########################################################################
 ## ARM720T Systems
 #########################################################################
@@ -959,6 +1010,9 @@ impa7_config	:	unconfig
 ep7312_config	:	unconfig
 	@./mkconfig $(@:_config=) arm arm720t ep7312

+modnet50_config :	unconfig
+	@./mkconfig $(@:_config=) arm arm720t modnet50
+
 #########################################################################
 ## XScale Systems
 #########################################################################
@@ -1085,6 +1139,24 @@ DK1S10_config:	unconfig
 		}
 	@./mkconfig -a DK1S10 nios nios dk1s10 altera

+ADNPESC1_DNPEVA2_base_32_config	\
+ADNPESC1_base_32_config		\
+ADNPESC1_config: unconfig
+	@ >include/config.h
+	@[ -z "$(findstring _DNPEVA2,$@)" ] || \
+		{ echo "#define CONFIG_DNPEVA2 1" >>include/config.h ; \
+		  echo "... DNP/EVA2 configuration" ; \
+		}
+	@[ -z "$(findstring _base_32,$@)" ] || \
+		{ echo "#define CONFIG_NIOS_BASE_32 1" >>include/config.h ; \
+		  echo "... NIOS 'base_32' configuration" ; \
+		}
+	@[ -z "$(findstring ADNPESC1_config,$@)" ] || \
+		{ echo "#define CONFIG_NIOS_BASE_32 1" >>include/config.h ; \
+		  echo "... NIOS 'base_32' configuration (DEFAULT)" ; \
+		}
+	@./mkconfig -a ADNPESC1 nios nios adnpesc1 ssv
+

 #########################################################################
 ## MIPS32 AU1X00
--- a/269
+++ b/269
@@ -122,135 +122,45 @@ Directory Hierarchy:
 - board		Board dependent files
 - common	Misc architecture independent functions
 - cpu		CPU specific files
+  - 74xx_7xx	Files specific to Motorola MPC74xx and 7xx CPUs
+  - arm720t	Files specific to ARM 720 CPUs
+  - arm920t	Files specific to ARM 920 CPUs
+  - arm925t	Files specific to ARM 925 CPUs
+  - arm926ejs	Files specific to ARM 926 CPUs
+  - at91rm9200	Files specific to Atmel AT91RM9200 CPUs
+  - i386	Files specific to i386 CPUs
+  - ixp		Files specific to Intel XScale IXP CPUs
+  - mcf52x2	Files specific to Motorola ColdFire MCF52x2 CPUs
+  - mips	Files specific to MIPS CPUs
+  - mpc5xx	Files specific to Motorola MPC5xx  CPUs
+  - mpc5xxx	Files specific to Motorola MPC5xxx CPUs
+  - mpc8xx	Files specific to Motorola MPC8xx  CPUs
+  - mpc824x	Files specific to Motorola MPC824x CPUs
+  - mpc8260	Files specific to Motorola MPC8260 CPUs
+  - mpc85xx	Files specific to Motorola MPC85xx CPUs
+  - nios	Files specific to Altera NIOS CPUs
+  - ppc4xx	Files specific to IBM PowerPC 4xx CPUs
+  - pxa		Files specific to Intel XScale PXA CPUs
+  - s3c44b0	Files specific to Samsung S3C44B0 CPUs
+  - sa1100	Files specific to Intel StrongARM SA1100 CPUs
 - disk		Code for disk drive partition handling
 - doc		Documentation (don't expect too much)
 - drivers	Commonly used device drivers
 - dtt		Digital Thermometer and Thermostat drivers
 - examples	Example code for standalone applications, etc.
 - include	Header Files
- disk		Harddisk interface code
+- lib_arm	Files generic to ARM	 architecture
+- lib_generic	Files generic to all	 architectures
+- lib_i386	Files generic to i386	 architecture
+- lib_m68k	Files generic to m68k	 architecture
+- lib_mips	Files generic to MIPS	 architecture
+- lib_nios	Files generic to NIOS	 architecture
+- lib_ppc	Files generic to PowerPC architecture
 - net		Networking code
- ppc		Files generic to PowerPC architecture
 - post		Power On Self Test
- post/arch		Symlink to architecture specific Power On Self Test
- post/arch-ppc		PowerPC architecture specific Power On Self Test
- post/cpu/mpc8260	MPC8260 CPU specific Power On Self Test
- post/cpu/mpc8xx	MPC8xx CPU specific Power On Self Test
 - rtc		Real Time Clock drivers
 - tools		Tools to build S-Record or U-Boot images, etc.

- cpu/74xx_7xx	Files specific to Motorola MPC74xx and 7xx CPUs
- cpu/arm925t	Files specific to ARM	   925	   CPUs
- cpu/arm926ejs Files specific to ARM	926	CPUs
- cpu/mpc5xx	Files specific to Motorola MPC5xx  CPUs
- cpu/mpc8xx	Files specific to Motorola MPC8xx  CPUs
- cpu/mpc824x	Files specific to Motorola MPC824x CPUs
- cpu/mpc8260	Files specific to Motorola MPC8260 CPU
- cpu/mpc85xx	Files specific to Motorola MPC85xx CPUs
- cpu/ppc4xx	Files specific to IBM	   4xx	   CPUs
-
-
- board/LEOX/	Files specific to boards manufactured by The LEOX team
- board/LEOX/elpt860	Files specific to ELPT860 boards
- board/RPXClassic
-		Files specific to RPXClassic boards
- board/RPXlite Files specific to RPXlite    boards
- board/at91rm9200dk Files specific to AT91RM9200DK boards
- board/c2mon	Files specific to c2mon	     boards
- board/cmi	Files specific to cmi	     boards
- board/cogent	Files specific to Cogent     boards
-		(need further configuration)
-		Files specific to CPCIISER4  boards
- board/cpu86	Files specific to CPU86	     boards
- board/cray/	Files specific to boards manufactured by Cray
- board/cray/L1		Files specific to L1	     boards
- board/cu824	Files specific to CU824	     boards
- board/ebony	Files specific to IBM Ebony board
- board/eric	Files specific to ERIC	     boards
- board/esd/	Files specific to boards manufactured by ESD
- board/esd/adciop	Files specific to ADCIOP     boards
- board/esd/ar405	Files specific to AR405	     boards
- board/esd/canbt	Files specific to CANBT	     boards
- board/esd/cpci405	Files specific to CPCI405    boards
- board/esd/cpciiser4	Files specific to CPCIISER4  boards
- board/esd/common	Common files for ESD boards
- board/esd/dasa_sim	Files specific to DASA_SIM   boards
- board/esd/du405	Files specific to DU405	     boards
- board/esd/ocrtc	Files specific to OCRTC	     boards
- board/esd/pci405	Files specific to PCI405     boards
- board/esteem192e
-		Files specific to ESTEEM192E boards
- board/etx094	Files specific to ETX_094    boards
- board/evb64260
-		Files specific to EVB64260   boards
- board/fads	Files specific to FADS	     boards
- board/flagadm Files specific to FLAGADM    boards
- board/gen860t Files specific to GEN860T and GEN860T_SC    boards
- board/genietv Files specific to GENIETV    boards
- board/gth	Files specific to GTH	     boards
- board/hermes	Files specific to HERMES     boards
- board/hymod	Files specific to HYMOD	     boards
- board/icu862	Files specific to ICU862     boards
- board/ip860	Files specific to IP860	     boards
- board/iphase4539
-		Files specific to Interphase4539 boards
- board/ivm	Files specific to IVMS8/IVML24 boards
- board/lantec	Files specific to LANTEC     boards
- board/lwmon	Files specific to LWMON	     boards
- board/Marvell Files specific to Marvell development boards
- board/Marvell/db64360 Files specific to db64360 board
- board/Marvell/db64460 Files specific to db64460 board
- board/mbx8xx	Files specific to MBX	     boards
- board/mpc8260ads
-		Files specific to MPC826xADS and PQ2FADS-ZU/VR boards
- board/mpc8540ads
-		Files specific to MPC8540ADS boards
- board/mpc8560ads
-		Files specific to MPC8560ADS boards
- board/mpl/	Files specific to boards manufactured by MPL
- board/mpl/common	Common files for MPL boards
- board/mpl/pip405	Files specific to PIP405     boards
- board/mpl/mip405	Files specific to MIP405     boards
- board/mpl/vcma9	Files specific to VCMA9	     boards
- board/musenki Files specific to MUSEKNI    boards
- board/mvs1	Files specific to MVS1	     boards
- board/nx823	Files specific to NX823	     boards
- board/oxc	Files specific to OXC	     boards
- board/omap1510inn
-		Files specific to OMAP 1510 Innovator boards
- board/omap1610inn
-		Files specific to OMAP 1610 Innovator boards
- board/pcippc2 Files specific to PCIPPC2/PCIPPC6 boards
- board/pm826	Files specific to PM826	     boards
- board/ppmc8260
-		Files specific to PPMC8260   boards
- board/snmc/qs850	Files specific to QS850/823  boards
- board/snmc/qs860t	Files specific to QS860T     boards
- board/rpxsuper
-		Files specific to RPXsuper   boards
- board/rsdproto
-		Files specific to RSDproto   boards
- board/sandpoint
-		Files specific to Sandpoint  boards
- board/sbc8260 Files specific to SBC8260    boards
- board/sacsng	Files specific to SACSng     boards
- board/siemens Files specific to boards manufactured by Siemens AG
- board/siemens/CCM	Files specific to CCM	     boards
- board/siemens/IAD210	Files specific to IAD210     boards
- board/siemens/SCM	Files specific to SCM	     boards
- board/siemens/pcu_e	Files specific to PCU_E	     boards
- board/sixnet	Files specific to SIXNET     boards
- board/spd8xx	Files specific to SPD8xxTS   boards
- board/tqm8260 Files specific to TQM8260    boards
- board/tqm8xx	Files specific to TQM8xxL    boards
- board/w7o	Files specific to W7O	     boards
- board/walnut405
-		Files specific to Walnut405  boards
- board/westel/ Files specific to boards manufactured by Westel Wireless
- board/westel/amx860	Files specific to AMX860     boards
- board/utx8245 Files specific to UTX8245   boards
- board/zpc1900 Files specific to Zephyr Engineering ZPC.1900 board
-
 Software Configuration:
 =======================

@@ -375,11 +285,12 @@ The following options need to be configured:
 		ARM based boards:
 		-----------------

-		CONFIG_HHP_CRADLE,  CONFIG_DNP1110,    CONFIG_EP7312,
-		CONFIG_IMPA7,	    CONFIG_LART,       CONFIG_LUBBOCK,
-		CONFIG_INNOVATOROMAP1510,	CONFIG_INNOVATOROMAP1610
-		CONFIG_SHANNON,	    CONFIG_SMDK2400,   CONFIG_SMDK2410,
-		CONFIG_TRAB,	    CONFIG_VCMA9,      CONFIG_AT91RM9200DK
+		CONFIG_HHP_CRADLE,  CONFIG_DNP1110,	CONFIG_EP7312,
+		CONFIG_IMPA7,	    CONFIG_LART,	CONFIG_LUBBOCK,
+		CONFIG_INNOVATOROMAP1510,      CONFIG_INNOVATOROMAP1610,
+		CONFIG_H2_OMAP1610, CONFIG_SHANNON,	CONFIG_SMDK2400,
+		CONFIG_SMDK2410,    CONFIG_TRAB,	CONFIG_VCMA9,
+		CONFIG_AT91RM9200DK


 - CPU Module Type: (if CONFIG_COGENT is defined)
@@ -644,6 +555,7 @@ The following options need to be configured:
 		CFG_CMD_IMLS	  List all found images
 		CFG_CMD_IMMAP	* IMMR dump support
 		CFG_CMD_IRQ	* irqinfo
+		CFG_CMD_ITEST	* Integer/string test of 2 values
 		CFG_CMD_JFFS2	* JFFS2 Support
 		CFG_CMD_KGDB	* kgdb
 		CFG_CMD_LOADB	  loadb
@@ -748,16 +660,31 @@ The following options need to be configured:
 		one partition type as well.

 - IDE Reset method:
-		CONFIG_IDE_RESET_ROUTINE
+		CONFIG_IDE_RESET_ROUTINE - this is defined in several
+		board configurations files but used nowhere!

-		Set this to define that instead of a reset Pin, the
-		routine ide_set_reset(int idereset) will be used.
+		CONFIG_IDE_RESET - is this is defined, IDE Reset will
+		be performed by calling the function
+			ide_set_reset(int reset)
+		which has to be defined in a board specific file

 - ATAPI Support:
 		CONFIG_ATAPI

 		Set this to enable ATAPI support.

+- LBA48 Support
+		CONFIG_LBA48
+
+		Set this to enable support for disks larger than 137GB
+		Also look at CFG_64BIT_LBA ,CFG_64BIT_VSPRINTF and CFG_64BIT_STRTOUL
+		Whithout these , LBA48 support uses 32bit variables and will 'only'
+		support disks up to 2.1TB.
+
+		CFG_64BIT_LBA:
+			When enabled, makes the IDE subsystem use 64bit sector addresses.
+			Default is 32bit.
+
 - SCSI Support:
 		At the moment only there is only support for the
 		SYM53C8XX SCSI controller; define
@@ -804,7 +731,7 @@ The following options need to be configured:

 - USB Support:
 		At the moment only the UHCI host controller is
-		supported (PIP405, MIP405); define
+		supported (PIP405, MIP405, MPC5200); define
 		CONFIG_USB_UHCI to enable it.
 		define CONFIG_USB_KEYBOARD to enable the USB Keyboard
 		end define CONFIG_USB_STORAGE to enable the USB
@@ -812,6 +739,13 @@ The following options need to be configured:
 		Note:
 		Supported are USB Keyboards and USB Floppy drives
 		(TEAC FD-05PUB).
+		MPC5200 USB requires additional defines:
+			CONFIG_USB_CLOCK
+				for 528 MHz Clock: 0x0001bbbb
+			CONFIG_USB_CONFIG
+				for differential drivers: 0x00001000
+				for single ended drivers: 0x00005000
+

 - MMC Support:
 		The MMC controller on the Intel PXA is supported. To
@@ -1151,60 +1085,6 @@ The following options need to be configured:
 		SPI configuration items (port pins to use, etc). For
 		an example, see include/configs/sacsng.h.

- FPGA Support: CONFIG_FPGA_COUNT
-
-		Specify the number of FPGA devices to support.
-
-		CONFIG_FPGA
-
-		Used to specify the types of FPGA devices. For
-		example,
-		#define CONFIG_FPGA  CFG_XILINX_VIRTEX2
-
-		CFG_FPGA_PROG_FEEDBACK
-
-		Enable printing of hash marks during FPGA
-		configuration.
-
-		CFG_FPGA_CHECK_BUSY
-
-		Enable checks on FPGA configuration interface busy
-		status by the configuration function. This option
-		will require a board or device specific function to
-		be written.
-
-		CONFIG_FPGA_DELAY
-
-		If defined, a function that provides delays in the
-		FPGA configuration driver.
-
-		CFG_FPGA_CHECK_CTRLC
-
-		Allow Control-C to interrupt FPGA configuration
-
-		CFG_FPGA_CHECK_ERROR
-
-		Check for configuration errors during FPGA bitfile
-		loading. For example, abort during Virtex II
-		configuration if the INIT_B line goes low (which
-		indicated a CRC error).
-
-		CFG_FPGA_WAIT_INIT
-
-		Maximum time to wait for the INIT_B line to deassert
-		after PROB_B has been deasserted during a Virtex II
-		FPGA configuration sequence. The default time is 500 mS.
-
-		CFG_FPGA_WAIT_BUSY
-
-		Maximum time to wait for BUSY to deassert during
-		Virtex II FPGA configuration. The default is 5 mS.
-
-		CFG_FPGA_WAIT_CONFIG
-
-		Time to wait after FPGA configuration. The default is
-		200 mS.
-
 - FPGA Support: CONFIG_FPGA_COUNT

 		Specify the number of FPGA devices to support.
@@ -1410,6 +1290,20 @@ The following options need to be configured:
 		allows to read/write in Dataflash via the standard
 		commands cp, md...

+- SystemACE Support:
+		CONFIG_SYSTEMACE
+
+		Adding this option adds support for Xilinx SystemACE
+		chips attached via some sort of local bus. The address
+		of the chip must alsh be defined in the
+		CFG_SYSTEMACE_BASE macro. For example:
+
+		#define CONFIG_SYSTEMACE
+		#define CFG_SYSTEMACE_BASE 0xf0000000
+
+		When SystemACE support is added, the "ace" device type
+		becomes available to the fat commands, i.e. fatls.
+
 - Show boot progress:
 		CONFIG_SHOW_BOOT_PROGRESS

@@ -1450,6 +1344,10 @@ The following options need to be configured:
   14	common/cmd_bootm.c	No initial ramdisk, no multifile, continue.
   15	common/cmd_bootm.c	All preparation done, transferring control to OS

+  -30	lib_ppc/board.c		Fatal error, hang the system
+  -31	post/post.c		POST test failed, detected by post_output_backlog()
+  -32	post/post.c		POST test failed, detected by post_run_single()
+
   -1	common/cmd_doc.c	Bad usage of "doc" command
   -1	common/cmd_doc.c	No boot device
   -1	common/cmd_doc.c	Unknown Chip ID on boot device
@@ -1837,6 +1735,13 @@ use the "saveenv" command to store a valid environment.
 - CFG_FAULT_MII_ADDR:
 		MII address of the PHY to check for the Ethernet link state.

+- CFG_64BIT_VSPRINTF:
+		Makes vsprintf (and all *printf functions) support printing
+		of 64bit values by using the L quantifier
+
+- CFG_64BIT_STRTOUL:
+		Adds simple_strtoull that returns a 64bit value
+
 Low Level (hardware related) configuration options:
 ---------------------------------------------------

@@ -2024,7 +1929,7 @@ configurations; the following names are supported:
    at91rm9200dk_config	  omap1510inn_config	MPC8260ADS_config
    omap1610inn_config	  ZPC1900_config	MPC8540ADS_config
    MPC8560ADS_config	  QS850_config		QS823_config
-    QS860T_config	  DUET_ADS_config
+    QS860T_config	  DUET_ADS_config	omap1610h2_config

 Note: for some board special configuration names may exist; check  if
      additional  information is available from the board vendor; for
--- a/board/cogent/mb.c
+++ b/board/cogent/mb.c
@@ -235,7 +235,7 @@ int misc_init_f (void)

 long int initdram (int board_type)
 {
-#if CONFIG_CMA111
+#ifdef CONFIG_CMA111
 	return (32L * 1024L * 1024L);
 #else
 	unsigned char dipsw_val;
--- a/board/csb272/Makefile
+++ b/board/csb272/Makefile
@@ -0,0 +1,51 @@
+#
+# (C) Copyright 2000-2004
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+#OBJS	= $(BOARD).o flash.o
+#OBJS	= $(BOARD).o strataflash.o
+OBJS	= $(BOARD).o
+
+SOBJS	= init.o
+
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) crv $@ $^
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+sinclude .depend
+
+#########################################################################
--- a/board/csb272/config.mk
+++ b/board/csb272/config.mk
@@ -0,0 +1,36 @@
+#
+# (C) Copyright 2000-2004
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# (C) Copyright 2004
+# Tolunay Orkun, NextIO Inc., torkun@nextio.com.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# Cogent CSB272 board
+#
+
+LDFLAGS += $(LINKER_UNDEFS)
+
+TEXT_BASE := 0xFFFC0000
+#TEXT_BASE := 0x00100000
+
+PLATFORM_RELFLAGS := $(PLATFORM_RELFLAGS)
--- a/board/csb272/csb272.c
+++ b/board/csb272/csb272.c
@@ -0,0 +1,173 @@
+/*
+ * (C) Copyright 2004
+ * Tolunay Orkun, Nextio Inc., torkun@nextio.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/processor.h>
+#include <i2c.h>
+#include <miiphy.h>
+#include <405gp_enet.h>
+
+/*
+ * Configuration data for AMIS FS6377-01 Programmable 3-PLL Clock Generator
+ *
+ * CLKA output => Epson LCD Controller
+ * CLKB output => Not Connected
+ * CLKC output => Ethernet
+ * CLKD output => UART external clock
+ *
+ * Note: these values are obtained from device after init by micromonitor
+*/
+uchar pll_fs6377_regs[16] = {
+	0x28, 0xef, 0x53, 0x03, 0x4b, 0x80, 0x32, 0x80,
+	0x94, 0x32, 0x80, 0xd4, 0x56, 0xf6, 0xf6, 0xe0 };
+
+/*
+ * pll_init: Initialize AMIS IC FS6377-01 PLL
+ *
+ * PLL supplies Epson LCD Clock, Ethernet Clock and UART external clock
+ *
+ */
+int pll_init(void)
+{
+	i2c_init(CFG_I2C_SPEED, CFG_I2C_SLAVE);
+
+	return  i2c_write(CFG_I2C_PLL_ADDR, 0, 1,
+		(uchar *) pll_fs6377_regs, sizeof(pll_fs6377_regs));
+}
+
+/*
+ * board_early_init_f: do early board initialization
+ *
+ */
+int board_early_init_f(void)
+{
+	/* initialize PLL so UART, LCD, Ethernet clocked at correctly */
+	(void) get_clocks();
+	pll_init();
+
+   /*-------------------------------------------------------------------------+
+   | Interrupt controller setup for the Walnut board.
+   | Note: IRQ 0-15  405GP internally generated; active high; level sensitive
+   |       IRQ 16    405GP internally generated; active low; level sensitive
+   |       IRQ 17-24 RESERVED
+   |       IRQ 25 (EXT IRQ 0) FPGA; active high; level sensitive
+   |       IRQ 26 (EXT IRQ 1) SMI; active high; level sensitive
+   |       IRQ 27 (EXT IRQ 2) Not Used
+   |       IRQ 28 (EXT IRQ 3) PCI SLOT 3; active low; level sensitive
+   |       IRQ 29 (EXT IRQ 4) PCI SLOT 2; active low; level sensitive
+   |       IRQ 30 (EXT IRQ 5) PCI SLOT 1; active low; level sensitive
+   |       IRQ 31 (EXT IRQ 6) PCI SLOT 0; active low; level sensitive
+   | Note for Walnut board:
+   |       An interrupt taken for the FPGA (IRQ 25) indicates that either
+   |       the Mouse, Keyboard, IRDA, or External Expansion caused the
+   |       interrupt. The FPGA must be read to determine which device
+   |       caused the interrupt. The default setting of the FPGA clears
+   |
+   +-------------------------------------------------------------------------*/
+
+	mtdcr (uicsr, 0xFFFFFFFF);   /* clear all ints */
+	mtdcr (uicer, 0x00000000);   /* disable all ints */
+	mtdcr (uiccr, 0x00000000);   /* set all to be non-critical */
+	mtdcr (uicpr, 0xFFFFFF83);   /* set int polarities */
+	mtdcr (uictr, 0x10000000);   /* set int trigger levels */
+	mtdcr (uicvcr, 0x00000001);  /* set vect base=0,INT0 highest priority */
+	mtdcr (uicsr, 0xFFFFFFFF);   /* clear all ints */
+
+	mtebc (epcr, 0xa8400000);   /* EBC always driven */
+
+	return 0; /* success */
+}
+
+/*
+ * checkboard: identify/verify the board we are running
+ *
+ * Remark: we just assume it is correct board here!
+ *
+ */
+int checkboard(void)
+{
+	printf("BOARD: Cogent CSB272\n");
+
+	return 0; /* success */
+}
+
+/*
+ * initram: Determine the size of mounted DRAM
+ *
+ * Size is determined by reading SDRAM configuration registers as
+ * configured by initialization code
+ *
+ */
+long initdram (int board_type)
+{
+	ulong tot_size;
+	ulong bank_size;
+	ulong tmp;
+
+	tot_size = 0;
+
+	mtdcr (memcfga, mem_mb0cf);
+	tmp = mfdcr (memcfgd);
+	if (tmp & 0x00000001) {
+		bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
+		tot_size += bank_size;
+	}
+
+	mtdcr (memcfga, mem_mb1cf);
+	tmp = mfdcr (memcfgd);
+	if (tmp & 0x00000001) {
+		bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
+		tot_size += bank_size;
+	}
+
+	mtdcr (memcfga, mem_mb2cf);
+	tmp = mfdcr (memcfgd);
+	if (tmp & 0x00000001) {
+		bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
+		tot_size += bank_size;
+	}
+
+	mtdcr (memcfga, mem_mb3cf);
+	tmp = mfdcr (memcfgd);
+	if (tmp & 0x00000001) {
+		bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
+		tot_size += bank_size;
+	}
+
+	return tot_size;
+}
+
+/*
+ * last_stage_init: final configurations (such as PHY etc)
+ *
+ */
+int last_stage_init(void)
+{
+	/* initialize the PHY */
+	miiphy_reset(CONFIG_PHY_ADDR);
+	miiphy_write(CONFIG_PHY_ADDR, PHY_BMCR,
+			PHY_BMCR_AUTON | PHY_BMCR_RST_NEG);	/* AUTO neg */
+	miiphy_write(CONFIG_PHY_ADDR, PHY_FCSCR, 0x0d08);	/* LEDs     */
+
+	return 0; /* success */
+}
--- a/board/csb272/init.S
+++ b/board/csb272/init.S
@@ -0,0 +1,216 @@
+/******************************************************************************
+ *
+ *	 This source code has been made available to you by IBM on an AS-IS
+ *	 basis.	 Anyone receiving this source is licensed under IBM
+ *	 copyrights to use it in any way he or she deems fit, including
+ *	 copying it, modifying it, compiling it, and redistributing it either
+ *	 with or without modifications.	 No license under IBM patents or
+ *	 patent applications is to be implied by the copyright license.
+ *
+ *	 Any user of this software should understand that IBM cannot provide
+ *	 technical support for this software and will not be responsible for
+ *	 any consequences resulting from the use of this software.
+ *
+ *	 Any person who transfers this source code or any derivative work
+ *	 must include the IBM copyright notice, this paragraph, and the
+ *	 preceding two paragraphs in the transferred software.
+ *
+ *	 COPYRIGHT   I B M   CORPORATION 1995
+ *	 LICENSED MATERIAL  -  PROGRAM PROPERTY OF I B M
+ *
+ *****************************************************************************/
+#include <config.h>
+#include <ppc4xx.h>
+
+#define _LINUX_CONFIG_H 1	/* avoid reading Linux autoconf.h file	*/
+
+#include <ppc_asm.tmpl>
+#include <ppc_defs.h>
+
+#include <asm/cache.h>
+#include <asm/mmu.h>
+
+#define LI32(reg,val) \
+	addis   reg,0,val@h;\
+	ori     reg,reg,val@l
+
+#define WDCR_EBC(reg,val) \
+	addi    r4,0,reg;\
+	mtdcr   ebccfga,r4;\
+	addis   r4,0,val@h;\
+	ori     r4,r4,val@l;\
+	mtdcr   ebccfgd,r4
+
+#define WDCR_SDRAM(reg,val) \
+	addi    r4,0,reg;\
+	mtdcr   memcfga,r4;\
+	addis   r4,0,val@h;\
+	ori     r4,r4,val@l;\
+	mtdcr   memcfgd,r4
+
+/******************************************************************************
+ * Function:	ext_bus_cntlr_init
+ *
+ * Description:	Configures EBC Controller and a few basic chip selects.
+ *
+ *		CS0 is setup to get the Boot Flash out of the addresss range
+ *		so that we may setup a stack.  CS7 is setup so that we can
+ *		access and reset the hardware watchdog.
+ *
+ *		IMPORTANT: For pass1 this code must run from
+ *		cache since you can not reliably change a peripheral banks
+ *		timing register (pbxap) while running code from that bank.
+ *		For ex., since we are running from ROM on bank 0, we can NOT
+ *		execute the code that modifies bank 0 timings from ROM, so
+ *		we run it from cache.
+ *
+ * Notes:	Does NOT use the stack.
+ *****************************************************************************/
+	.section ".text"
+	.align	2
+	.globl	ext_bus_cntlr_init
+	.type	ext_bus_cntlr_init, @function
+ext_bus_cntlr_init:
+	mflr	r0
+	/********************************************************************
+	 * Prefetch entire ext_bus_cntrl_init function into the icache.
+	 * This is necessary because we are going to change the same CS we
+	 * are executing from.  Otherwise a CPU lockup may occur.
+	 *******************************************************************/
+	bl	..getAddr
+..getAddr:
+	mflr	r3			/* get address of ..getAddr */
+
+	/* Calculate number of cache lines for this function */
+	addi	r4, 0, (((.Lfe0 - ..getAddr) / CFG_CACHELINE_SIZE) + 2)
+	mtctr	r4
+..ebcloop:
+	icbt	r0, r3			/* prefetch cache line for addr in r3*/
+	addi	r3, r3, CFG_CACHELINE_SIZE /* move to next cache line */
+	bdnz	..ebcloop		/* continue for $CTR cache lines */
+
+	/********************************************************************
+	 * Delay to ensure all accesses to ROM are complete before changing
+	 * bank 0 timings. 200usec should be enough.
+	 * 200,000,000 (cycles/sec) X .000200 (sec) = 0x9C40 cycles.
+	 *******************************************************************/
+	addis	r3, 0, 0x0
+	ori	r3, r3, 0xA000		/* wait 200us from reset */
+	mtctr	r3
+..spinlp:
+	bdnz	..spinlp		/* spin loop */
+
+	/********************************************************************
+	 * SETUP CPC0_CR0
+	 *******************************************************************/
+	LI32(r4, 0x007000c0)
+	mtdcr	cntrl0, r4
+
+	/********************************************************************
+	 * Setup CPC0_CR1: Change PCIINT signal to PerWE
+	 *******************************************************************/
+	mfdcr	r4, cntrl1
+	ori	r4, r4, 0x4000
+	mtdcr	cntrl1, r4
+
+	/********************************************************************
+	 * Setup External Bus Controller (EBC).
+	 *******************************************************************/
+	WDCR_EBC(epcr, 0xd84c0000)
+	/********************************************************************
+	 * Memory Bank 0 (Intel 28F128J3 Flash) initialization
+	 *******************************************************************/
+	/*WDCR_EBC(pb0ap, 0x02869200)*/
+	WDCR_EBC(pb0ap, 0x07869200)
+	WDCR_EBC(pb0cr, 0xfe0bc000)
+	/********************************************************************
+	 * Memory Bank 1 (Holtek HT6542B PS/2) initialization
+	 *******************************************************************/
+	WDCR_EBC(pb1ap, 0x1f869200)
+	WDCR_EBC(pb1cr, 0xf0818000)
+	/********************************************************************
+	 * Memory Bank 2 (Epson S1D13506) initialization
+	 *******************************************************************/
+	WDCR_EBC(pb2ap, 0x05860300)
+	WDCR_EBC(pb2cr, 0xf045a000)
+	/********************************************************************
+	 * Memory Bank 3 (Philips SJA1000 CAN Controllers) initialization
+	 *******************************************************************/
+	WDCR_EBC(pb3ap, 0x0387d200)
+	WDCR_EBC(pb3cr, 0xf021c000)
+	/********************************************************************
+	 * Memory Bank 4-7 (Unused) initialization
+	 *******************************************************************/
+	WDCR_EBC(pb4ap, 0)
+	WDCR_EBC(pb4cr, 0)
+	WDCR_EBC(pb5ap, 0)
+	WDCR_EBC(pb5cr, 0)
+	WDCR_EBC(pb6ap, 0)
+	WDCR_EBC(pb6cr, 0)
+	WDCR_EBC(pb7ap, 0)
+	WDCR_EBC(pb7cr, 0)
+
+	/* We are all done */
+	mtlr	r0			/* Restore link register */
+	blr				/* Return to calling function */
+.Lfe0:	.size	ext_bus_cntlr_init,.Lfe0-ext_bus_cntlr_init
+/* end ext_bus_cntlr_init() */
+
+/******************************************************************************
+ * Function:	sdram_init
+ *
+ * Description:	Configures SDRAM memory banks.
+ *
+ * Notes:	Does NOT use the stack.
+ *****************************************************************************/
+	.section ".text"
+	.align	2
+	.globl	sdram_init
+	.type	sdram_init, @function
+sdram_init:
+
+	/*
+	 * Disable memory controller to allow
+	 * values to be changed.
+	 */
+	WDCR_SDRAM(mem_mcopt1, 0x00000000)
+
+	/*
+	 * Configure Memory Banks
+	 */
+	WDCR_SDRAM(mem_mb0cf, 0x00084001)
+	WDCR_SDRAM(mem_mb1cf, 0x00000000)
+	WDCR_SDRAM(mem_mb2cf, 0x00000000)
+	WDCR_SDRAM(mem_mb3cf, 0x00000000)
+
+	/*
+	 * Set up SDTR1 (SDRAM Timing Register)
+	 */
+	WDCR_SDRAM(mem_sdtr1, 0x00854009)
+
+	/*
+	 * Set RTR (Refresh Timing Register)
+	 */
+	WDCR_SDRAM(mem_rtr,   0x10000000)
+	/* WDCR_SDRAM(mem_rtr,   0x05f00000) */
+
+	/********************************************************************
+	 * Delay to ensure 200usec have elapsed since reset. Assume worst
+	 * case that the core is running 200Mhz:
+	 *	  200,000,000 (cycles/sec) X .000200 (sec) = 0x9C40 cycles
+	 *******************************************************************/
+	addis   r3, 0, 0x0000
+	ori     r3, r3, 0xA000		/* Wait >200us from reset */
+	mtctr   r3
+..spinlp2:
+	bdnz    ..spinlp2		/* spin loop */
+
+	/********************************************************************
+	 * Set memory controller options reg, MCOPT1.
+	 *******************************************************************/
+	WDCR_SDRAM(mem_mcopt1,0x80800000)
+
+..sdri_done:
+	blr				/* Return to calling function */
+.Lfe1:	.size	sdram_init,.Lfe1-sdram_init
+/* end sdram_init() */
--- a/board/csb272/u-boot.lds
+++ b/board/csb272/u-boot.lds
@@ -0,0 +1,151 @@
+/*
+ * (C) Copyright 2000-2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+/* Do we need any of these for elf?
+   __DYNAMIC = 0;    */
+SECTIONS
+{
+  .resetvec 0xFFFFFFFC :
+  {
+    *(.resetvec)
+  } = 0xffff
+
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)		}
+  .rela.text     : { *(.rela.text) 	}
+  .rel.data      : { *(.rel.data)		}
+  .rela.data     : { *(.rela.data) 	}
+  .rel.rodata    : { *(.rel.rodata) 	}
+  .rela.rodata   : { *(.rela.rodata) 	}
+  .rel.got       : { *(.rel.got)		}
+  .rela.got      : { *(.rela.got)		}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)		}
+  .rela.bss      : { *(.rela.bss)		}
+  .rel.plt       : { *(.rel.plt)		}
+  .rela.plt      : { *(.rela.plt)		}
+  .init          : { *(.init)	}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    /* WARNING - the following is hand-optimized to fit within	*/
+    /* the sector layout of our flash chips!	XXX FIXME XXX	*/
+
+    cpu/ppc4xx/start.o	(.text)
+    board/csb272/init.o	(.text)
+    cpu/ppc4xx/kgdb.o	(.text)
+    cpu/ppc4xx/traps.o	(.text)
+    cpu/ppc4xx/interrupts.o	(.text)
+    cpu/ppc4xx/serial.o	(.text)
+    cpu/ppc4xx/cpu_init.o	(.text)
+    cpu/ppc4xx/speed.o	(.text)
+    cpu/ppc4xx/405gp_enet.o	(.text)
+    common/dlmalloc.o	(.text)
+    lib_generic/crc32.o		(.text)
+
+    lib_ppc/extable.o	(.text)
+    lib_ppc/board.o	(.text)
+    lib_generic/zlib.o	(.text)
+/*    . = env_offset;*/
+/*    common/environment.o(.text)*/
+
+    *(.text)
+    *(.fixup)
+    *(.got1)
+  }
+  _etext = .;
+  PROVIDE (etext = .);
+  .rodata    :
+  {
+    *(.rodata)
+    *(.rodata1)
+    *(.rodata.str1.4)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x00FF) & 0xFFFFFF00;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
+  __fixup_entries = (. - _FIXUP_TABLE_)>>2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  __u_boot_cmd_start = .;
+  .u_boot_cmd : { *(.u_boot_cmd) }
+  __u_boot_cmd_end = .;
+
+
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(256);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(256);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+  _end = . ;
+  PROVIDE (end = .);
+}
--- a/board/dave/B2/B2.c
+++ b/board/dave/B2/B2.c
@@ -0,0 +1,128 @@
+/*
+ * (C) Copyright 2004
+ * DAVE Srl
+ * http://www.dave-tech.it
+ * http://www.wawnet.biz
+ * mailto:info@wawnet.biz
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/hardware.h>
+
+/*
+ * Miscelaneous platform dependent initialization
+ */
+
+int board_init (void)
+{
+	DECLARE_GLOBAL_DATA_PTR;
+	u32 temp;
+
+	/* Configuration Port Control Register*/
+	/* Port A */
+	PCONA = 0x3ff;
+
+	/* Port B */
+	PCONB = 0xff;
+	PDATB = 0xFFFF;
+
+	/* Port C */
+	/*
+	PCONC = 0xff55ff15;
+	PDATC = 0x0;
+	PUPC = 0xffff;
+	*/
+
+	/* Port D */
+	/*
+	PCOND = 0xaaaa;
+	PUPD = 0xff;
+	*/
+
+	/* Port E */
+	PCONE = 0x0001aaa9;
+	PDATE = 0x0;
+	PUPE = 0xff;
+
+	/* Port F */
+	PCONF = 0x124955;
+	PDATF  = 0xff; /* B2-eth_reset tied high level */
+	/*
+	PUPF = 0x1e3;
+	*/
+
+	/* Port G */
+	PUPG = 0x1;
+	PCONG = 0x3; /*PG0= EINT0= ETH_INT prepared for linux kernel*/
+
+	INTMSK = 0x03fffeff;
+	INTCON = 0x05;
+
+    /*
+    	Configure chip ethernet interrupt as High level
+    	Port G EINT 0-7 EINT0 -> CHIP ETHERNET
+    */
+	temp = EXTINT;
+   	temp &= ~0x7;
+    temp |= 0x1; /*LEVEL_HIGH*/
+	EXTINT = temp;
+
+    /*
+    	Reset SMSC LAN91C96 chip
+    */
+    temp= PCONF;
+    temp |= 0x00000040;
+    PCONF = temp;
+
+	/* Reset high */
+    temp = PDATF;
+    temp |= (1 << 3);
+    PDATF = temp;
+
+    /* Short delay */
+    for (temp=0;temp<10;temp++)
+    {
+		/* NOP */
+    }
+
+    /* Reset low */
+    temp = PDATF;
+    temp &= ~(1 << 3);
+    PDATF = temp;
+
+	/* arch number MACH_TYPE_MBA44B0 */
+	gd->bd->bi_arch_number = 178;
+
+	/* location of boot parameters */
+	gd->bd->bi_boot_params = 0x0c000100;
+
+	return 0;
+}
+
+int dram_init (void)
+{
+	DECLARE_GLOBAL_DATA_PTR;
+
+	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
+
+	return (0);
+}
--- a/board/dave/B2/Makefile
+++ b/board/dave/B2/Makefile
@@ -0,0 +1,48 @@
+#
+# (C) Copyright 2002
+# Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+# Marius Groeger <mgroeger@sysgo.de>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	:= B2.o flash.o
+SOBJS	:= memsetup.o
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) crv $@ $(OBJS) $(SOBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+-include .depend
+
+#########################################################################
--- a/board/dave/B2/config.mk
+++ b/board/dave/B2/config.mk
@@ -0,0 +1,30 @@
+#
+# (C) Copyright 2000
+# Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+# Marius Groeger <mgroeger@sysgo.de>
+#
+# (C) Copyright 2000-2004
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+TEXT_BASE = 0x0C100000
+
+PLATFORM_CPPFLAGS += -Uarm
--- a/board/dave/B2/flash.c
+++ b/board/dave/B2/flash.c
@@ -0,0 +1,76 @@
+/*
+ * (C) Copyright 2001
+ * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/hardware.h>
+
+/*
+ * include common flash code (for esd boards)
+ */
+#include "../common/flash.c"
+
+/*-----------------------------------------------------------------------
+ * Functions
+ */
+static ulong flash_get_size (vu_long * addr, flash_info_t * info);
+static void flash_get_offsets (ulong base, flash_info_t * info);
+
+/*-----------------------------------------------------------------------
+ */
+
+unsigned long flash_init (void)
+{
+#ifdef __DEBUG_START_FROM_SRAM__
+	return CFG_DUMMY_FLASH_SIZE;
+#else
+	unsigned long size_b0;
+	int i;
+
+	/* Init: no FLASHes known */
+	for (i=0; i<CFG_MAX_FLASH_BANKS; ++i) {
+		flash_info[i].flash_id = FLASH_UNKNOWN;
+	}
+
+	/* Static FLASH Bank configuration here - FIXME XXX */
+
+	size_b0 = flash_get_size((vu_long *)CFG_FLASH_BASE, &flash_info[0]);
+
+	if (flash_info[0].flash_id == FLASH_UNKNOWN) {
+		printf ("## Unknown FLASH on Bank 0 - Size = 0x%08lx = %ld MB\n",
+			size_b0, size_b0<<20);
+	}
+
+	/* Setup offsets */
+	flash_get_offsets (0, &flash_info[0]);
+
+	/* Monitor protection ON by default */
+	(void)flash_protect(FLAG_PROTECT_SET,
+			    -CFG_MONITOR_LEN,
+			    0xffffffff,
+			    &flash_info[0]);
+
+	flash_info[0].size = size_b0;
+
+	return (size_b0);
+#endif
+}
--- a/board/dave/B2/memsetup.S
+++ b/board/dave/B2/memsetup.S
@@ -0,0 +1,167 @@
+/*
+ * (C) Copyright 2004
+ * DAVE Srl
+ *
+ * http://www.dave-tech.it
+ * http://www.wawnet.biz
+ * mailto:info@wawnet.biz
+ *
+ * memsetup-sa1110.S (blob): memory setup for various SA1110 architectures
+ * Modified By MATTO
+ *
+ * Copyright (C) 2001 Erik Mouw (J.A.K.Mouw@its.tudelft.nl)
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ *
+ */
+
+/*
+ * Documentation:
+ * Intel Corporation, "Intel StrongARM SA-1110 Microprocessor
+ *     Advanced Developer's manual, December 1999
+ *
+ * Intel has a very hard to find SDRAM configurator on their web site:
+ *   http://appzone.intel.com/hcd/sa1110/memory/index.asp
+ *
+ * NOTE: This code assumes that an SA1110 CPU *always* uses SDRAM. This
+ * appears to be true, but it might be possible that somebody designs a
+ * board with mixed EDODRAM/SDRAM memory (which is a bad idea). -- Erik
+ *
+ * 04-10-2001:  SELETZ
+ * - separated memory config for multiple platform support
+ * - perform SA1110 Hardware Reset Procedure
+ *
+ */
+
+.equ    B0_Tacs,      0x0 /* 0clk */
+.equ    B0_Tcos,      0x0 /* 0clk */
+.equ    B0_Tacc,      0x4 /* 6clk */
+.equ    B0_Tcoh,      0x0 /* 0clk */
+.equ    B0_Tah,       0x0 /* 0clk */
+.equ    B0_Tacp,      0x0 /* 0clk */
+.equ    B0_PMC,       0x0 /* normal(1data) */
+/* Bank 1 parameter */
+.equ    B1_Tacs,      0x3 /* 4clk */
+.equ    B1_Tcos,      0x3 /* 4clk */
+.equ    B1_Tacc,      0x7 /* 14clkv */
+.equ    B1_Tcoh,      0x3 /* 4clk */
+.equ    B1_Tah,       0x3 /* 4clk */
+.equ    B1_Tacp,      0x3 /* 6clk */
+.equ    B1_PMC,       0x0 /* normal(1data) */
+
+/* Bank 2 parameter - LAN91C96 */
+.equ    B2_Tacs,      0x3 /* 4clk */
+.equ    B2_Tcos,      0x3 /* 4clk */
+.equ    B2_Tacc,      0x7 /* 14clk */
+.equ    B2_Tcoh,      0x3 /* 4clk */
+.equ    B2_Tah,       0x3 /* 4clk */
+.equ    B2_Tacp,      0x3 /* 6clk */
+.equ    B2_PMC,       0x0 /* normal(1data) */
+
+/* Bank 3 parameter */
+.equ    B3_Tacs,      0x3 /* 4clk */
+.equ    B3_Tcos,      0x3 /* 4clk */
+.equ    B3_Tacc,      0x7 /* 14clk */
+.equ    B3_Tcoh,      0x3 /* 4clk */
+.equ    B3_Tah,       0x3 /* 4clk */
+.equ    B3_Tacp,      0x3 /* 6clk */
+.equ    B3_PMC,       0x0 /* normal(1data) */
+
+/* Bank 4 parameter */
+.equ    B4_Tacs,      0x3 /* 4clk */
+.equ    B4_Tcos,      0x3 /* 4clk */
+.equ    B4_Tacc,      0x7 /* 14clk */
+.equ    B4_Tcoh,      0x3 /* 4clk */
+.equ    B4_Tah,       0x3 /* 4clk */
+.equ    B4_Tacp,      0x3 /* 6clk */
+.equ    B4_PMC,       0x0 /* normal(1data) */
+
+/* Bank 5 parameter */
+.equ    B5_Tacs,      0x3 /* 4clk */
+.equ    B5_Tcos,      0x3 /* 4clk */
+.equ    B5_Tacc,      0x7 /* 14clk */
+.equ    B5_Tcoh,      0x3 /* 4clk */
+.equ    B5_Tah,       0x3 /* 4clk */
+.equ    B5_Tacp,      0x3 /* 6clk */
+.equ    B5_PMC,       0x0 /* normal(1data) */
+
+/* Bank 6(if SROM) parameter */
+.equ    B6_Tacs,      0x3 /* 4clk */
+.equ    B6_Tcos,      0x3 /* 4clk */
+.equ    B6_Tacc,      0x7 /* 14clk */
+.equ    B6_Tcoh,      0x3 /* 4clk */
+.equ    B6_Tah,       0x3 /* 4clk */
+.equ    B6_Tacp,      0x3 /* 6clk */
+.equ    B6_PMC,       0x0 /* normal(1data) */
+
+/* Bank 7(if SROM) parameter */
+.equ    B7_Tacs,      0x3 /* 4clk */
+.equ    B7_Tcos,      0x3 /* 4clk */
+.equ    B7_Tacc,      0x7 /* 14clk */
+.equ    B7_Tcoh,      0x3 /* 4clk */
+.equ    B7_Tah,       0x3 /* 4clk */
+.equ    B7_Tacp,      0x3 /* 6clk */
+.equ    B7_PMC,       0x0 /* normal(1data) */
+
+/* Bank 6 parameter */
+.equ    B6_MT,        0x3 /* SDRAM */
+.equ    B6_Trcd,      0x0 /* 2clk */
+.equ    B6_SCAN,      0x0 /* 10bit */
+
+.equ    B7_MT,        0x3 /* SDRAM */
+.equ    B7_Trcd,      0x0 /* 2clk */
+.equ    B7_SCAN,      0x0 /* 10bit */
+
+
+/* REFRESH parameter */
+.equ    REFEN,        0x1 /* Refresh enable */
+.equ    TREFMD,       0x0 /* CBR(CAS before RAS)/Auto refresh */
+.equ    Trp,        0x0 /* 2clk */
+.equ    Trc,        0x3 /* 0x1=5clk 0x3=11clk*/
+.equ    Tchr,       0x0 /* 0x2=3clk 0x0=0clks  */
+.equ    REFCNT,       879
+
+MEMORY_CONFIG:
+  .long   0x12111900 /* Bank0 = OM[1:0] , Bank1-7 16bit, Bank2=Nowait,UB/LB*/
+  .word ((B0_Tacs<<13)+(B0_Tcos<<11)+(B0_Tacc<<8)+(B0_Tcoh<<6)+(B0_Tah<<4)+(B0_Tacp<<2)+(B0_PMC)) /*GCS0*/
+  .word ((B1_Tacs<<13)+(B1_Tcos<<11)+(B1_Tacc<<8)+(B1_Tcoh<<6)+(B1_Tah<<4)+(B1_Tacp<<2)+(B1_PMC)) /*GCS1*/
+  .word ((B2_Tacs<<13)+(B2_Tcos<<11)+(B2_Tacc<<8)+(B2_Tcoh<<6)+(B2_Tah<<4)+(B2_Tacp<<2)+(B2_PMC)) /*GCS2*/
+  .word ((B3_Tacs<<13)+(B3_Tcos<<11)+(B3_Tacc<<8)+(B3_Tcoh<<6)+(B3_Tah<<4)+(B3_Tacp<<2)+(B3_PMC)) /*GCS3*/
+  .word ((B4_Tacs<<13)+(B4_Tcos<<11)+(B4_Tacc<<8)+(B4_Tcoh<<6)+(B4_Tah<<4)+(B4_Tacp<<2)+(B4_PMC)) /*GCS4*/
+  .word ((B5_Tacs<<13)+(B5_Tcos<<11)+(B5_Tacc<<8)+(B5_Tcoh<<6)+(B5_Tah<<4)+(B5_Tacp<<2)+(B5_PMC)) /*GCS5*/
+  .word ((B6_MT<<15)+(B6_Trcd<<2)+(B6_SCAN))  /*GCS6*/
+  .word ((B7_MT<<15)+(B7_Trcd<<2)+(B7_SCAN))  /*GCS7*/
+  .word ((REFEN<<23)+(TREFMD<<22)+(Trp<<20)+(Trc<<18)+(Tchr<<16)+REFCNT)  /*REFRESH RFEN=1, TREFMD=0, trp=3clk, trc=5clk, tchr=3clk,count=1019*/
+  .word 0x17      /*SCLK power down mode, BANKSIZE 16M/16M*/
+  .word 0x20      /*MRSR6 CL=2clk*/
+  .word 0x20      /*MRSR7*/
+
+
+.globl memsetup
+memsetup:
+
+	/*
+		the next instruction fail due memory relocation...
+		we'll find the right MEMORY_CONFIG address with the next 3 lines...
+	*/
+	/*ldr r0, =MEMORY_CONFIG*/
+	mov r0, pc
+	ldr r1, =(0x38+4)
+	sub r0, r0, r1
+
+	ldmia r0, {r1-r13}
+	ldr   r0, =0x01c80000
+	stmia r0, {r1-r13}
+	mov pc, lr
--- a/board/dave/B2/u-boot.lds
+++ b/board/dave/B2/u-boot.lds
@@ -0,0 +1,57 @@
+/*
+ * (C) Copyright 2000-2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+	. = 0x00000000;
+
+	. = ALIGN(4);
+	.text      :
+	{
+	  cpu/s3c44b0/start.o	(.text)
+	  *(.text)
+	}
+
+	. = ALIGN(4);
+	.rodata : { *(.rodata) }
+
+	. = ALIGN(4);
+	.data : { *(.data) }
+
+	. = ALIGN(4);
+	.got : { *(.got) }
+
+  __u_boot_cmd_start = .;
+  .u_boot_cmd : { *(.u_boot_cmd) }
+  __u_boot_cmd_end = .;
+
+	armboot_end_data = .;
+
+	. = ALIGN(4);
+	__bss_start = .;
+	.bss : { *(.bss) }
+	_end = .;
+}
--- a/board/dave/common/flash.c
+++ b/board/dave/common/flash.c
@@ -22,7 +22,6 @@
 */

 #include <common.h>
-#include <ppc4xx.h>
 #include <asm/processor.h>

 flash_info_t	flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips	*/
@@ -578,15 +577,27 @@ int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
 	if ((l = addr - wp) != 0) {
 		data = 0;
 		for (i=0, cp=wp; i<l; ++i, ++cp) {
+#ifdef CONFIG_B2
+			data = data | ((*(uchar *)cp)<<(8*i));
+#else
 			data = (data << 8) | (*(uchar *)cp);
+#endif
 		}
 		for (; i<4 && cnt>0; ++i) {
+#ifdef CONFIG_B2
+			data = data  | ((*src++)<<(8*i));
+#else
 			data = (data << 8) | *src++;
+#endif
 			--cnt;
 			++cp;
 		}
 		for (; cnt==0 && i<4; ++i, ++cp) {
+#ifdef CONFIG_B2
+			data = data | ((*(uchar *)cp)<<(8*i));
+#else
 			data = (data << 8) | (*(uchar *)cp);
+#endif
 		}

 		if ((rc = write_word(info, wp, data)) != 0) {
@@ -600,9 +611,14 @@ int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
 	 */
 	while (cnt >= 4) {
 		data = 0;
+#ifdef CONFIG_B2
+		data = (*(ulong*)src);
+		src += 4;
+#else
 		for (i=0; i<4; ++i) {
 			data = (data << 8) | *src++;
 		}
+#endif
 		if ((rc = write_word(info, wp, data)) != 0) {
 			return (rc);
 		}
@@ -619,11 +635,19 @@ int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
 	 */
 	data = 0;
 	for (i=0, cp=wp; i<4 && cnt>0; ++i, ++cp) {
+#ifdef CONFIG_B2
+		data = data  | ((*src++)<<(8*i));
+#else
 		data = (data << 8) | *src++;
+#endif
 		--cnt;
 	}
 	for (; i<4; ++i, ++cp) {
+#ifdef CONFIG_B2
+		data = data | ((*(uchar *)cp)<<(8*i));
+#else
 		data = (data << 8) | (*(uchar *)cp);
+#endif
 	}

 	return (write_word(info, wp, data));
--- a/board/eXalion/Makefile
+++ b/board/eXalion/Makefile
@@ -0,0 +1,41 @@
+#
+# (C) Copyright 2001
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	= $(BOARD).o
+SOBJS	=
+
+$(LIB):	.depend $(OBJS) $(SOBJS)
+	$(AR) crv $@ $^
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+sinclude .depend
+
+#########################################################################
--- a/board/eXalion/config.mk
+++ b/board/eXalion/config.mk
@@ -0,0 +1,31 @@
+#
+# (C) Copyright 2000, 2001
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# Sandpoint boards
+#
+
+#TEXT_BASE = 0x00090000
+TEXT_BASE = 0xFFF00000
+
+PLATFORM_CPPFLAGS += -DTEXT_BASE=$(TEXT_BASE)
--- a/board/eXalion/eXalion.c
+++ b/board/eXalion/eXalion.c
@@ -0,0 +1,292 @@
+/*
+ * (C) Copyright 2000-2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * (C) Copyright 2002
+ * Torsten Demke, FORCE Computers GmbH. torsten.demke@fci.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <mpc824x.h>
+#include <asm/processor.h>
+#include <asm/io.h>
+#include <pci.h>
+#include <ide.h>
+#include "piix_pci.h"
+#include "eXalion.h"
+
+int checkboard (void)
+{
+	ulong busfreq = get_bus_freq (0);
+	char buf[32];
+
+	printf ("Board: eXalion MPC824x - CHRP (MAP B)\n");
+	printf ("Built: %s at %s\n", __DATE__, __TIME__);
+	printf ("Local Bus:  %s MHz\n", strmhz (buf, busfreq));
+
+	return 0;
+}
+
+int checkflash (void)
+{
+	printf ("checkflash\n");
+	flash_init ();
+	return (0);
+}
+
+long int initdram (int board_type)
+{
+	int i, cnt;
+	volatile uchar *base = CFG_SDRAM_BASE;
+	volatile ulong *addr;
+	ulong save[32];
+	ulong val, ret = 0;
+
+	for (i = 0, cnt = (CFG_MAX_RAM_SIZE / sizeof (long)) >> 1; cnt > 0;
+	     cnt >>= 1) {
+		addr = (volatile ulong *) base + cnt;
+		save[i++] = *addr;
+		*addr = ~cnt;
+	}
+
+	addr = (volatile ulong *) base;
+	save[i] = *addr;
+	*addr = 0;
+
+	if (*addr != 0) {
+		*addr = save[i];
+		goto Done;
+	}
+
+	for (cnt = 1; cnt <= CFG_MAX_RAM_SIZE / sizeof (long); cnt <<= 1) {
+		addr = (volatile ulong *) base + cnt;
+		val = *addr;
+		*addr = save[--i];
+		if (val != ~cnt) {
+			ulong new_bank0_end = cnt * sizeof (long) - 1;
+			ulong mear1 = mpc824x_mpc107_getreg (MEAR1);
+			ulong emear1 = mpc824x_mpc107_getreg (EMEAR1);
+
+			mear1 = (mear1 & 0xFFFFFF00) |
+				((new_bank0_end & MICR_ADDR_MASK) >>
+				 MICR_ADDR_SHIFT);
+			emear1 = (emear1 & 0xFFFFFF00) |
+				((new_bank0_end & MICR_ADDR_MASK) >>
+				 MICR_EADDR_SHIFT);
+			mpc824x_mpc107_setreg (MEAR1, mear1);
+			mpc824x_mpc107_setreg (EMEAR1, emear1);
+
+			ret = cnt * sizeof (long);
+			goto Done;
+		}
+	}
+
+	ret = CFG_MAX_RAM_SIZE;
+      Done:
+	return ret;
+}
+
+int misc_init_r (void)
+{
+	pci_dev_t bdf;
+	u32 val32;
+	u8 val8;
+
+	puts ("ISA:   ");
+	bdf = pci_find_device (PIIX4_VENDOR_ID, PIIX4_ISA_DEV_ID, 0);
+	if (bdf == -1) {
+		puts ("Unable to find PIIX4 ISA bridge !\n");
+		hang ();
+	}
+
+	/* set device for normal ISA instead EIO */
+	pci_read_config_dword (bdf, PCI_CFG_PIIX4_GENCFG, &val32);
+	val32 |= 0x00000001;
+	pci_write_config_dword (bdf, PCI_CFG_PIIX4_GENCFG, val32);
+	printf ("PIIX4 ISA bridge (%d,%d,%d)\n", PCI_BUS (bdf),
+		PCI_DEV (bdf), PCI_FUNC (bdf));
+
+	puts ("ISA:   ");
+	bdf = pci_find_device (PIIX4_VENDOR_ID, PIIX4_IDE_DEV_ID, 0);
+	if (bdf == -1) {
+		puts ("Unable to find PIIX4 IDE controller !\n");
+		hang ();
+	}
+
+	/* Init BMIBA register  */
+	/* pci_read_config_dword(bdf, PCI_CFG_PIIX4_BMIBA, &val32); */
+	/* val32 |= 0x1000; */
+	/* pci_write_config_dword(bdf, PCI_CFG_PIIX4_BMIBA, val32); */
+
+	/* Enable BUS master and IO access  */
+	val32 = PCI_COMMAND_MASTER | PCI_COMMAND_IO;
+	pci_write_config_dword (bdf, PCI_COMMAND, val32);
+
+	/* Set latency  */
+	pci_read_config_byte (bdf, PCI_LATENCY_TIMER, &val8);
+	val8 = 0x40;
+	pci_write_config_byte (bdf, PCI_LATENCY_TIMER, val8);
+
+	/* Enable Primary ATA/IDE  */
+	pci_read_config_dword (bdf, PCI_CFG_PIIX4_IDETIM, &val32);
+	/* val32 = 0xa307a307; */
+	val32 = 0x00008000;
+	pci_write_config_dword (bdf, PCI_CFG_PIIX4_IDETIM, val32);
+
+
+	printf ("PIIX4 IDE controller (%d,%d,%d)\n", PCI_BUS (bdf),
+		PCI_DEV (bdf), PCI_FUNC (bdf));
+
+	/* Try to get FAT working... */
+	/* fat_register_read(ide_read); */
+
+
+	return (0);
+}
+
+/*
+ * Show/Init PCI devices on the specified bus number.
+ */
+
+void pci_eXalion_fixup_irq (struct pci_controller *hose, pci_dev_t dev)
+{
+	unsigned char line;
+
+	switch (PCI_DEV (dev)) {
+	case 16:
+		line = PCI_INT_A;
+		break;
+	case 17:
+		line = PCI_INT_B;
+		break;
+	case 18:
+		line = PCI_INT_C;
+		break;
+	case 19:
+		line = PCI_INT_D;
+		break;
+#if defined (CONFIG_MPC8245)
+	case 20:
+		line = PCI_INT_A;
+		break;
+	case 21:
+		line = PCI_INT_B;
+		break;
+	case 22:
+		line = PCI_INT_NA;
+		break;
+#endif
+	default:
+		line = PCI_INT_A;
+		break;
+	}
+	pci_hose_write_config_byte (hose, dev, PCI_INTERRUPT_LINE, line);
+}
+
+
+/*
+ * Initialize PCI Devices, report devices found.
+ */
+#ifndef CONFIG_PCI_PNP
+#if defined (CONFIG_MPC8240)
+static struct pci_config_table pci_eXalion_config_table[] = {
+	{
+	 /* Intel 82559ER ethernet controller */
+	 PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, 0x00, 18, 0x00,
+	 pci_cfgfunc_config_device, {PCI_ENET0_IOADDR,
+				     PCI_ENET0_MEMADDR,
+				     PCI_COMMAND_MEMORY |
+				     PCI_COMMAND_MASTER}},
+	{
+	 /* Intel 82371AB PIIX4 PCI to ISA bridge */
+	 PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, 0x00, 20, 0x00,
+	 pci_cfgfunc_config_device, {0,
+				     0,
+				     PCI_COMMAND_IO | PCI_COMMAND_MASTER}},
+	{
+	 /* Intel 82371AB PIIX4 IDE controller */
+	 PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, 0x00, 20, 0x01,
+	 pci_cfgfunc_config_device, {0,
+				     0,
+				     PCI_COMMAND_IO | PCI_COMMAND_MASTER}},
+	{}
+};
+#elif defined (CONFIG_MPC8245)
+static struct pci_config_table pci_eXalion_config_table[] = {
+	{
+	 /* Intel 82559ER ethernet controller */
+	 PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, 0x00, 17, 0x00,
+	 pci_cfgfunc_config_device, {PCI_ENET0_IOADDR,
+				     PCI_ENET0_MEMADDR,
+				     PCI_COMMAND_MEMORY |
+				     PCI_COMMAND_MASTER}},
+	{
+	 /* Intel 82559ER ethernet controller */
+	 PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, 0x00, 18, 0x00,
+	 pci_cfgfunc_config_device, {PCI_ENET1_IOADDR,
+				     PCI_ENET1_MEMADDR,
+				     PCI_COMMAND_MEMORY |
+				     PCI_COMMAND_MASTER}},
+	{
+	 /* Broadcom BCM5690 Gigabit switch */
+	 PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, 0x00, 20, 0x00,
+	 pci_cfgfunc_config_device, {PCI_ENET2_IOADDR,
+				     PCI_ENET2_MEMADDR,
+				     PCI_COMMAND_MEMORY |
+				     PCI_COMMAND_MASTER}},
+	{
+	 /* Broadcom BCM5690 Gigabit switch */
+	 PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, 0x00, 21, 0x00,
+	 pci_cfgfunc_config_device, {PCI_ENET3_IOADDR,
+				     PCI_ENET3_MEMADDR,
+				     PCI_COMMAND_MEMORY |
+				     PCI_COMMAND_MASTER}},
+	{
+	 /* Intel 82371AB PIIX4 PCI to ISA bridge */
+	 PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, 0x00, 22, 0x00,
+	 pci_cfgfunc_config_device, {0,
+				     0,
+				     PCI_COMMAND_IO | PCI_COMMAND_MASTER}},
+	{
+	 /* Intel 82371AB PIIX4 IDE controller */
+	 PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, 0x00, 22, 0x01,
+	 pci_cfgfunc_config_device, {0,
+				     0,
+				     PCI_COMMAND_IO | PCI_COMMAND_MASTER}},
+	{}
+};
+#else
+#error Specific type of MPC824x must be defined (i.e. CONFIG_MPC8240)
+#endif
+
+#endif /* #ifndef CONFIG_PCI_PNP */
+
+struct pci_controller hose = {
+#ifndef CONFIG_PCI_PNP
+	config_table:pci_eXalion_config_table,
+	fixup_irq:pci_eXalion_fixup_irq,
+#endif
+};
+
+void pci_init_board (void)
+{
+	pci_mpc824x_init (&hose);
+}
--- a/board/eXalion/eXalion.h
+++ b/board/eXalion/eXalion.h
@@ -0,0 +1,52 @@
+/*
+ * (C) Copyright 2002
+ * Torsten Demke, FORCE Computers GmbH. torsten.demke@fci.com
+ *
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * (C) Copyright 2002
+ * James Dougherty (jfd@broadcom.com)
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __EXALION_H
+#define __EXALION_H
+
+/* IRQ settings */
+#define  PCI_INT_NA (0xff)   /* PCI Intr. not used */
+#define  PCI_INT_A  (0x09)   /* PCI Intr. A Interrupt Request Line Nr. */
+#define  PCI_INT_B  (0x0a)   /* PCI Intr. B Interrupt Request Line Nr. */
+#define  PCI_INT_C  (0x0b)   /* PCI Intr. C Interrupt Request Line Nr. */
+#define  PCI_INT_D  (0x0c)   /* PCI Intr. D Interrupt Request Line Nr. */
+#if defined (CPU_MPC8245)
+#define  LN_1_INT     PCI_INT_B  /* ethernet interrupt level */
+#define  LN_2_INT     PCI_INT_C  /* ethernet interrupt level */
+#define  BCM_1_INT    PCI_INT_A  /* BCM5690 interrupt level */
+#define  BCM_2_INT    PCI_INT_B  /* BCM5690 interrupt level */
+#elif defined (CPU_MPC8240)
+#define  BCM_INT      PCI_INT_B  /* BCM5600 interrupt level */
+#define  LN_INT       PCI_INT_C  /* ethernet interrupt level */
+#endif
+
+#ifndef __ASSEMBLY__
+#endif /* !__ASSEMBLY__ */
+
+#endif /* __EXALION_H */
--- a/board/eXalion/piix_pci.h
+++ b/board/eXalion/piix_pci.h
@@ -0,0 +1,172 @@
+/*
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * (C) Copyright 2002
+ * Torsten Demke, FORCE Computers GmbH. torsten.demke@fci.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#ifndef _PIIX4_PCI_H
+#define _PIIX4_PCI_H
+
+#include <common.h>
+#include <mpc824x.h>
+#include <asm/processor.h>
+#include <asm/io.h>
+#include <pci.h>
+
+#define PIIX4_VENDOR_ID         0x8086
+#define PIIX4_ISA_DEV_ID        0x7110
+#define PIIX4_IDE_DEV_ID        0x7111
+
+/* Function 0 ISA Bridge */
+#define PCI_CFG_PIIX4_IORT      0x4C    /* 8 bit ISA Recovery Timer Reg (default 0x4D) */
+#define PCI_CFG_PIIX4_XBCS      0x4E    /* 16 bit XBus Chip select reg (default 0x0003) */
+#define PCI_CFG_PIIX4_PIRQC     0x60    /* PCI IRQ Route Register 4 x 8bit (default )*/
+#define PCI_CFG_PIIX4_SERIRQ    0x64
+#define PCI_CFG_PIIX4_TOM       0x69
+#define PCI_CFG_PIIX4_MSTAT     0x6A
+#define PCI_CFG_PIIX4_MBDMA     0x76
+#define PCI_CFG_PIIX4_APICBS    0x80
+#define PCI_CFG_PIIX4_DLC       0x82
+#define PCI_CFG_PIIX4_PDMACFG   0x90
+#define PCI_CFG_PIIX4_DDMABS    0x92
+#define PCI_CFG_PIIX4_GENCFG    0xB0
+#define PCI_CFG_PIIX4_RTCCFG    0xCB
+
+/* IO Addresses */
+#define PIIX4_ISA_DMA1_CH0BA    0x00
+#define PIIX4_ISA_DMA1_CH0CA    0x01
+#define PIIX4_ISA_DMA1_CH1BA    0x02
+#define PIIX4_ISA_DMA1_CH1CA    0x03
+#define PIIX4_ISA_DMA1_CH2BA    0x04
+#define PIIX4_ISA_DMA1_CH2CA    0x05
+#define PIIX4_ISA_DMA1_CH3BA    0x06
+#define PIIX4_ISA_DMA1_CH3CA    0x07
+#define PIIX4_ISA_DMA1_CMDST    0x08
+#define PIIX4_ISA_DMA1_REQ      0x09
+#define PIIX4_ISA_DMA1_WSBM     0x0A
+#define PIIX4_ISA_DMA1_CH_MOD   0x0B
+#define PIIX4_ISA_DMA1_CLR_PT   0x0C
+#define PIIX4_ISA_DMA1_M_CLR    0x0D
+#define PIIX4_ISA_DMA1_CLR_M    0x0E
+#define PIIX4_ISA_DMA1_RWAMB    0x0F
+
+#define PIIX4_ISA_DMA2_CH0BA    0xC0
+#define PIIX4_ISA_DMA2_CH0CA    0xC1
+#define PIIX4_ISA_DMA2_CH1BA    0xC2
+#define PIIX4_ISA_DMA2_CH1CA    0xC3
+#define PIIX4_ISA_DMA2_CH2BA    0xC4
+#define PIIX4_ISA_DMA2_CH2CA    0xC5
+#define PIIX4_ISA_DMA2_CH3BA    0xC6
+#define PIIX4_ISA_DMA2_CH3CA    0xC7
+#define PIIX4_ISA_DMA2_CMDST    0xD0
+#define PIIX4_ISA_DMA2_REQ      0xD2
+#define PIIX4_ISA_DMA2_WSBM     0xD4
+#define PIIX4_ISA_DMA2_CH_MOD   0xD6
+#define PIIX4_ISA_DMA2_CLR_PT   0xD8
+#define PIIX4_ISA_DMA2_M_CLR    0xDA
+#define PIIX4_ISA_DMA2_CLR_M    0xDC
+#define PIIX4_ISA_DMA2_RWAMB    0xDE
+
+#define PIIX4_ISA_INT1_ICW1     0x20
+#define PIIX4_ISA_INT1_OCW2     0x20
+#define PIIX4_ISA_INT1_OCW3     0x20
+#define PIIX4_ISA_INT1_ICW2     0x21
+#define PIIX4_ISA_INT1_ICW3     0x21
+#define PIIX4_ISA_INT1_ICW4     0x21
+#define PIIX4_ISA_INT1_OCW1     0x21
+
+#define PIIX4_ISA_INT1_ELCR     0x4D0
+
+#define PIIX4_ISA_INT2_ICW1     0xA0
+#define PIIX4_ISA_INT2_OCW2     0xA0
+#define PIIX4_ISA_INT2_OCW3     0xA0
+#define PIIX4_ISA_INT2_ICW2     0xA1
+#define PIIX4_ISA_INT2_ICW3     0xA1
+#define PIIX4_ISA_INT2_ICW4     0xA1
+#define PIIX4_ISA_INT2_OCW1     0xA1
+#define PIIX4_ISA_INT2_IMR      0xA1 /* read only */
+
+#define PIIX4_ISA_INT2_ELCR     0x4D1
+
+#define PIIX4_ISA_TMR0_CNT_ST   0x40
+#define PIIX4_ISA_TMR1_CNT_ST   0x41
+#define PIIX4_ISA_TMR2_CNT_ST   0x42
+#define PIIX4_ISA_TMR_TCW       0x43
+
+#define PIIX4_ISA_RST_XBUS      0x60
+
+#define PIIX4_ISA_NMI_CNT_ST    0x61
+#define PIIX4_ISA_NMI_ENABLE    0x70
+
+#define PIIX4_ISA_RTC_INDEX     0x70
+#define PIIX4_ISA_RTC_DATA      0x71
+#define PIIX4_ISA_RTCEXT_IND    0x70
+#define PIIX4_ISA_RTCEXT_DATA   0x71
+
+#define PIIX4_ISA_DMA1_CH2LPG   0x81
+#define PIIX4_ISA_DMA1_CH3LPG   0x82
+#define PIIX4_ISA_DMA1_CH1LPG   0x83
+#define PIIX4_ISA_DMA1_CH0LPG   0x87
+#define PIIX4_ISA_DMA2_CH2LPG   0x89
+#define PIIX4_ISA_DMA2_CH3LPG   0x8A
+#define PIIX4_ISA_DMA2_CH1LPG   0x8B
+#define PIIX4_ISA_DMA2_LPGRFR   0x8F
+
+#define PIIX4_ISA_PORT_92       0x92
+
+#define PIIX4_ISA_APM_CONTRL    0xB2
+#define PIIX4_ISA_APM_STATUS    0xB3
+
+#define PIIX4_ISA_COCPU_ERROR   0xF0
+
+/* Function 1 IDE Controller */
+#define PCI_CFG_PIIX4_BMIBA     0x20
+#define PCI_CFG_PIIX4_IDETIM    0x40
+#define PCI_CFG_PIIX4_SIDETIM   0x44
+#define PCI_CFG_PIIX4_UDMACTL   0x48
+#define PCI_CFG_PIIX4_UDMATIM   0x4A
+
+/* Function 2 USB Controller */
+#define PCI_CFG_PIIX4_SBRNUM    0x60
+#define PCI_CFG_PIIX4_LEGSUP    0xC0
+
+/* Function 3 Power Management */
+#define PCI_CFG_PIIX4_PMAB      0x40
+#define PCI_CFG_PIIX4_CNTA      0x44
+#define PCI_CFG_PIIX4_CNTB      0x48
+#define PCI_CFG_PIIX4_GPICTL    0x4C
+#define PCI_CFG_PIIX4_DEVRESD   0x50
+#define PCI_CFG_PIIX4_DEVACTA   0x54
+#define PCI_CFG_PIIX4_DEVACTB   0x58
+#define PCI_CFG_PIIX4_DEVRESA   0x5C
+#define PCI_CFG_PIIX4_DEVRESB   0x60
+#define PCI_CFG_PIIX4_DEVRESC   0x64
+#define PCI_CFG_PIIX4_DEVRESE   0x68
+#define PCI_CFG_PIIX4_DEVRESF   0x6C
+#define PCI_CFG_PIIX4_DEVRESG   0x70
+#define PCI_CFG_PIIX4_DEVRESH   0x74
+#define PCI_CFG_PIIX4_DEVRESI   0x78
+#define PCI_CFG_PIIX4_PMMISC    0x80
+#define PCI_CFG_PIIX4_SMBBA     0x90
+
+
+#endif  /* _PIIX4_PCI_H */
--- a/board/eXalion/u-boot.lds
+++ b/board/eXalion/u-boot.lds
@@ -0,0 +1,133 @@
+/*
+ * (C) Copyright 2001
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+/* Do we need any of these for elf?
+   __DYNAMIC = 0;    */
+SECTIONS
+{
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)	}
+  .rela.text     : { *(.rela.text) 	}
+  .rel.data      : { *(.rel.data)	}
+  .rela.data     : { *(.rela.data) 	}
+  .rel.rodata    : { *(.rel.rodata) 	}
+  .rela.rodata   : { *(.rela.rodata) 	}
+  .rel.got       : { *(.rel.got)	}
+  .rela.got      : { *(.rela.got)	}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)	}
+  .rela.bss      : { *(.rela.bss)	}
+  .rel.plt       : { *(.rel.plt)	}
+  .rela.plt      : { *(.rela.plt)	}
+  .init          : { *(.init)		}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    cpu/mpc824x/start.o		(.text)
+    lib_ppc/board.o		(.text)
+    lib_ppc/ppcstring.o		(.text)
+    lib_generic/vsprintf.o	(.text)
+    lib_generic/crc32.o		(.text)
+    lib_generic/zlib.o		(.text)
+
+	. = DEFINED(env_offset) ? env_offset : .;
+    common/environment.o (.text)
+
+	*(.text)
+
+    *(.fixup)
+    *(.got1)
+    . = ALIGN(16);
+    *(.rodata)
+    *(.rodata1)
+    *(.rodata.str1.4)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x0FFF) & 0xFFFFF000;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2;
+  __fixup_entries = (. - _FIXUP_TABLE_) >> 2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  __u_boot_cmd_start = .;
+  .u_boot_cmd : { *(.u_boot_cmd) }
+  __u_boot_cmd_end = .;
+
+
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(4096);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(4096);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+
+  _end = . ;
+  PROVIDE (end = .);
+}
--- a/board/emk/common/flash.c
+++ b/board/emk/common/flash.c
@@ -28,15 +28,53 @@

 flash_info_t	flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips */

-typedef unsigned char FLASH_PORT_WIDTH;
-typedef volatile unsigned char FLASH_PORT_WIDTHV;
-#define	FLASH_ID_MASK	0xFF
+#if defined (CONFIG_TOP860)
+  typedef unsigned short FLASH_PORT_WIDTH;
+  typedef volatile unsigned short FLASH_PORT_WIDTHV;
+  #define	FLASH_ID_MASK	0xFF

-#define FPW	FLASH_PORT_WIDTH
-#define FPWV	FLASH_PORT_WIDTHV
+  #define FPW	FLASH_PORT_WIDTH
+  #define FPWV	FLASH_PORT_WIDTHV

-#define FLASH_CYCLE1	0x0aaa
-#define FLASH_CYCLE2	0x0555
+  #define FLASH_CYCLE1	0x0555
+  #define FLASH_CYCLE2	0x02aa
+  #define FLASH_ID1		0
+  #define FLASH_ID2		1
+  #define FLASH_ID3		0x0e
+  #define FLASH_ID4		0x0F
+#endif
+
+#if defined (CONFIG_TOP5200) && !defined (CONFIG_LITE5200)
+  typedef unsigned char FLASH_PORT_WIDTH;
+  typedef volatile unsigned char FLASH_PORT_WIDTHV;
+  #define	FLASH_ID_MASK	0xFF
+
+  #define FPW	FLASH_PORT_WIDTH
+  #define FPWV	FLASH_PORT_WIDTHV
+
+  #define FLASH_CYCLE1	0x0aaa
+  #define FLASH_CYCLE2	0x0555
+  #define FLASH_ID1		0
+  #define FLASH_ID2		2
+  #define FLASH_ID3		0x1c
+  #define FLASH_ID4		0x1E
+#endif
+
+#if defined (CONFIG_TOP5200) && defined (CONFIG_LITE5200)
+  typedef unsigned char FLASH_PORT_WIDTH;
+  typedef volatile unsigned char FLASH_PORT_WIDTHV;
+  #define	FLASH_ID_MASK	0xFF
+
+  #define FPW	FLASH_PORT_WIDTH
+  #define FPWV	FLASH_PORT_WIDTHV
+
+  #define FLASH_CYCLE1	0x0555
+  #define FLASH_CYCLE2	0x02aa
+  #define FLASH_ID1		0
+  #define FLASH_ID2		1
+  #define FLASH_ID3		0x0E
+  #define FLASH_ID4		0x0F
+#endif

 /*-----------------------------------------------------------------------
 * Functions
@@ -165,6 +203,15 @@ void flash_print_info (flash_info_t *info)
 	case FLASH_AM160B:
 		fmt = "29LV160%s (16 Mbit, %s)\n";
 		break;
+	case FLASH_AMLV640U:
+		fmt = "29LV640M (64 Mbit)\n";
+		break;
+	case FLASH_AMDLV065D:
+		fmt = "29LV065D (64 Mbit)\n";
+		break;
+	case FLASH_AMLV256U:
+		fmt = "29LV256M (256 Mbit)\n";
+		break;
 	default:
 		fmt = "Unknown Chip Type\n";
 		break;
@@ -179,12 +226,33 @@ void flash_print_info (flash_info_t *info)
 	printf ("  Sector Start Addresses:");

 	for (i=0; i<info->sector_count; ++i) {
+		ulong	size;
+		int		erased;
+		ulong	*flash = (unsigned long *) info->start[i];
+
 		if ((i % 5) == 0) {
 			printf ("\n   ");
 		}

-		printf (" %08lX%s", info->start[i],
-			info->protect[i] ? " (RO)" : "     ");
+		/*
+		 * Check if whole sector is erased
+		 */
+		size =
+			(i != (info->sector_count - 1)) ?
+			(info->start[i + 1] - info->start[i]) >> 2 :
+		(info->start[0] + info->size - info->start[i]) >> 2;
+
+		for (
+			flash = (unsigned long *) info->start[i], erased = 1;
+				(flash != (unsigned long *) info->start[i] + size) && erased;
+					flash++
+			)
+			erased = *flash == ~0x0UL;
+
+		printf (" %08lX %s %s",
+			info->start[i],
+			erased ? "E": " ",
+			info->protect[i] ? "(RO)" : "    ");
 	}

 	printf ("\n");
@@ -200,7 +268,6 @@ void flash_print_info (flash_info_t *info)
 ulong flash_get_size (FPWV *addr, flash_info_t *info)
 {
 	int		i;
-	ulong	offset;

 	/* Write auto select command: read Manufacturer ID */
 	/* Write auto select command sequence and test FLASH answer */
@@ -212,7 +279,7 @@ ulong flash_get_size (FPWV *addr, flash_info_t *info)
 	 * This works for any bus width and any FLASH device width.
 	 */
 	udelay(100);
-	switch (addr[0] & 0xff) {
+	switch (addr[FLASH_ID1] & 0xff) {

 	case (uchar)AMD_MANUFACT:
 		info->flash_id = FLASH_MAN_AMD;
@@ -225,7 +292,7 @@ ulong flash_get_size (FPWV *addr, flash_info_t *info)
 #endif

 	default:
-		printf ("unknown vendor=%x ", addr[0] & 0xff);
+		printf ("unknown vendor=%x ", addr[FLASH_ID1] & 0xff);
 		info->flash_id = FLASH_UNKNOWN;
 		info->sector_count = 0;
 		info->size = 0;
@@ -233,33 +300,70 @@ ulong flash_get_size (FPWV *addr, flash_info_t *info)
 	}

 	/* Check 16 bits or 32 bits of ID so work on 32 or 16 bit bus. */
-	if (info->flash_id != FLASH_UNKNOWN) switch ((FPW)addr[2]) {
+	if (info->flash_id != FLASH_UNKNOWN) switch ((FPW)addr[FLASH_ID2]) {

 	case (FPW)AMD_ID_LV160B:
 		info->flash_id += FLASH_AM160B;
 		info->sector_count = 35;
 		info->size = 0x00200000;
-#ifdef CFG_LOWBOOT
-		offset = 0;
-#else
-		offset = 0x00e00000;
-#endif
-		info->start[0] = (ulong)addr + offset;
-		info->start[1] = (ulong)addr + offset + 0x4000;
-		info->start[2] = (ulong)addr + offset + 0x6000;
-		info->start[3] = (ulong)addr + offset + 0x8000;
+		info->start[0] = (ulong)addr;
+		info->start[1] = (ulong)addr + 0x4000;
+		info->start[2] = (ulong)addr + 0x6000;
+		info->start[3] = (ulong)addr + 0x8000;
 		for (i = 4; i < info->sector_count; i++)
 		{
-			info->start[i] = (ulong)addr + offset + 0x10000 * (i-3);
+			info->start[i] = (ulong)addr + 0x10000 * (i-3);
 		}
 		break;

+	case (FPW)AMD_ID_LV065D:
+		info->flash_id += FLASH_AMDLV065D;
+		info->sector_count = 128;
+		info->size = 0x00800000;
+		for (i = 0; i < info->sector_count; i++)
+		{
+			info->start[i] = (ulong)addr + 0x10000 * i;
+		}
+		break;
+
+	case (FPW)AMD_ID_MIRROR:
+		/* MIRROR BIT FLASH, read more ID bytes */
+		if ((FPW)addr[FLASH_ID3] == (FPW)AMD_ID_LV640U_2 &&
+			(FPW)addr[FLASH_ID4] == (FPW)AMD_ID_LV640U_3)
+		{
+			info->flash_id += FLASH_AMLV640U;
+			info->sector_count = 128;
+			info->size = 0x00800000;
+			for (i = 0; i < info->sector_count; i++)
+			{
+				info->start[i] = (ulong)addr + 0x10000 * i;
+			}
+			break;
+		}
+		if ((FPW)addr[FLASH_ID3] == (FPW)AMD_ID_LV256U_2 &&
+			(FPW)addr[FLASH_ID4] == (FPW)AMD_ID_LV256U_3)
+		{
+			/* attention: only the first 16 MB will be used in u-boot */
+			info->flash_id += FLASH_AMLV256U;
+			info->sector_count = 256;
+			info->size = 0x01000000;
+			for (i = 0; i < info->sector_count; i++)
+			{
+				info->start[i] = (ulong)addr + 0x10000 * i;
+			}
+			break;
+		}
+
+		/* fall thru to here ! */
 	default:
-		printf ("unknown AMD device=%x ", (FPW)addr[2]);
+		printf ("unknown AMD device=%x %x %x",
+			(FPW)addr[FLASH_ID2],
+			(FPW)addr[FLASH_ID3],
+			(FPW)addr[FLASH_ID4]);
 		info->flash_id = FLASH_UNKNOWN;
 		info->sector_count = 0;
-		info->size = 0;
-		return (0);			/* => no or unknown flash */
+		info->size = 0x800000;
+		break;
 	}

 	/* Put FLASH back in read mode */
@@ -290,6 +394,7 @@ int	flash_erase (flash_info_t *info, int s_first, int s_last)

 	switch (info->flash_id & FLASH_TYPEMASK) {
 	case FLASH_AM160B:
+	case FLASH_AMLV640U:
 		break;
 	case FLASH_UNKNOWN:
 	default:
--- a/board/emk/top5200/Makefile
+++ b/board/emk/top5200/Makefile
@@ -26,7 +26,7 @@ include $(TOPDIR)/config.mk

 LIB	= lib$(BOARD).a

-OBJS	:= $(BOARD).o flash.o
+OBJS	:= $(BOARD).o ../common/flash.o ../common/vpd.o ../common/am79c874.o

 $(LIB):	$(OBJS) $(SOBJS)
 	$(AR) crv $@ $(OBJS)
--- a/board/emk/top5200/flash.c
+++ b/board/emk/top5200/flash.c
@@ -1,502 +0,0 @@
-/*
- * (C) Copyright 2003
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2003
- * Reinhard Meyer, EMK Elektronik GmbH, r.meyer@emk-elektronik.de
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-
-flash_info_t	flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips	*/
-
-typedef unsigned char FLASH_PORT_WIDTH;
-typedef volatile unsigned char FLASH_PORT_WIDTHV;
-#define	FLASH_ID_MASK	0xFF
-
-#define FPW	FLASH_PORT_WIDTH
-#define FPWV	FLASH_PORT_WIDTHV
-
-#define FLASH_CYCLE1	0x0aaa
-#define FLASH_CYCLE2	0x0555
-
-/*-----------------------------------------------------------------------
- * Functions
- */
-static ulong flash_get_size(FPWV *addr, flash_info_t *info);
-static void flash_reset(flash_info_t *info);
-static int write_word_amd(flash_info_t *info, FPWV *dest, FPW data);
-static flash_info_t *flash_get_info(ulong base);
-
-/*-----------------------------------------------------------------------
- * flash_init()
- *
- * sets up flash_info and returns size of FLASH (bytes)
- */
-unsigned long flash_init (void)
-{
-	unsigned long size = 0;
-	int i = 0;
-	extern void flash_preinit(void);
-	extern void flash_afterinit(uint, ulong, ulong);
-	ulong flashbase = CFG_FLASH_BASE;
-
-	flash_preinit();
-
-	/* There is only ONE FLASH device */
-	memset(&flash_info[i], 0, sizeof(flash_info_t));
-	flash_info[i].size =
-			flash_get_size((FPW *)flashbase, &flash_info[i]);
-	size += flash_info[i].size;
-
-#if CFG_MONITOR_BASE >= CFG_FLASH_BASE
-	/* monitor protection ON by default */
-	flash_protect(FLAG_PROTECT_SET,
-		      CFG_MONITOR_BASE,
-		      CFG_MONITOR_BASE+monitor_flash_len-1,
-		      flash_get_info(CFG_MONITOR_BASE));
-#endif
-
-#ifdef	CFG_ENV_IS_IN_FLASH
-	/* ENV protection ON by default */
-	flash_protect(FLAG_PROTECT_SET,
-		      CFG_ENV_ADDR,
-		      CFG_ENV_ADDR+CFG_ENV_SIZE-1,
-		      flash_get_info(CFG_ENV_ADDR));
-#endif
-
-
-	flash_afterinit(i, flash_info[i].start[0], flash_info[i].size);
-	return size ? size : 1;
-}
-
-/*-----------------------------------------------------------------------
- */
-static void flash_reset(flash_info_t *info)
-{
-	FPWV *base = (FPWV *)(info->start[0]);
-
-	/* Put FLASH back in read mode */
-	if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL)
-		*base = (FPW)0x00FF00FF;	/* Intel Read Mode */
-	else if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_AMD)
-		*base = (FPW)0x00F000F0;	/* AMD Read Mode */
-}
-
-/*-----------------------------------------------------------------------
- */
-
-static flash_info_t *flash_get_info(ulong base)
-{
-	int i;
-	flash_info_t * info;
-
-	for (i = 0; i < CFG_MAX_FLASH_BANKS; i ++) {
-		info = & flash_info[i];
-		if (info->size &&
-			info->start[0] <= base && base <= info->start[0] + info->size - 1)
-			break;
-	}
-
-	return i == CFG_MAX_FLASH_BANKS ? 0 : info;
-}
-
-/*-----------------------------------------------------------------------
- */
-
-void flash_print_info (flash_info_t *info)
-{
-	int i;
-	uchar *boottype;
-	uchar *bootletter;
-	uchar *fmt;
-	uchar botbootletter[] = "B";
-	uchar topbootletter[] = "T";
-	uchar botboottype[] = "bottom boot sector";
-	uchar topboottype[] = "top boot sector";
-
-	if (info->flash_id == FLASH_UNKNOWN) {
-		printf ("missing or unknown FLASH type\n");
-		return;
-	}
-
-	switch (info->flash_id & FLASH_VENDMASK) {
-	case FLASH_MAN_AMD:	printf ("AMD ");		break;
-#if 0
-	case FLASH_MAN_BM:	printf ("BRIGHT MICRO ");	break;
-	case FLASH_MAN_FUJ:	printf ("FUJITSU ");		break;
-	case FLASH_MAN_SST:	printf ("SST ");		break;
-	case FLASH_MAN_STM:	printf ("STM ");		break;
-	case FLASH_MAN_INTEL:	printf ("INTEL ");		break;
-#endif
-	default:		printf ("Unknown Vendor ");	break;
-	}
-
-	/* check for top or bottom boot, if it applies */
-	if (info->flash_id & FLASH_BTYPE) {
-		boottype = botboottype;
-		bootletter = botbootletter;
-	}
-	else {
-		boottype = topboottype;
-		bootletter = topbootletter;
-	}
-
-	switch (info->flash_id & FLASH_TYPEMASK) {
-	case FLASH_AM160T:
-	case FLASH_AM160B:
-		fmt = "29LV160%s (16 Mbit, %s)\n";
-		break;
-	case FLASH_AMDLV065D:
-		fmt = "29LV065 (64 Mbit, uniform sectors)\n";
-		break;
-	default:
-		fmt = "Unknown Chip Type\n";
-		break;
-	}
-
-	printf (fmt, bootletter, boottype);
-
-	printf ("  Size: %ld MB in %d Sectors\n",
-		info->size >> 20,
-		info->sector_count);
-
-	printf ("  Sector Start Addresses:");
-
-	for (i=0; i<info->sector_count; ++i) {
-		if ((i % 5) == 0) {
-			printf ("\n   ");
-		}
-
-		printf (" %08lX%s", info->start[i],
-			info->protect[i] ? " (RO)" : "     ");
-	}
-
-	printf ("\n");
-}
-
-/*-----------------------------------------------------------------------
- */
-
-/*
- * The following code cannot be run from FLASH!
- */
-
-ulong flash_get_size (FPWV *addr, flash_info_t *info)
-{
-	int		i;
-	ulong	offset;
-
-	/* Write auto select command: read Manufacturer ID */
-	/* Write auto select command sequence and test FLASH answer */
-	addr[FLASH_CYCLE1] = (FPW)0x00AA00AA;	/* for AMD, Intel ignores this */
-	addr[FLASH_CYCLE2] = (FPW)0x00550055;	/* for AMD, Intel ignores this */
-	addr[FLASH_CYCLE1] = (FPW)0x00900090;	/* selects Intel or AMD */
-
-	/* The manufacturer codes are only 1 byte, so just use 1 byte.
-	 * This works for any bus width and any FLASH device width.
-	 */
-	udelay(100);
-	switch (addr[0] & 0xff) {
-
-	case (uchar)AMD_MANUFACT:
-		info->flash_id = FLASH_MAN_AMD;
-		break;
-
-#if 0
-	case (uchar)INTEL_MANUFACT:
-		info->flash_id = FLASH_MAN_INTEL;
-		break;
-#endif
-
-	default:
-		printf ("unknown vendor=%x ", addr[0] & 0xff);
-		info->flash_id = FLASH_UNKNOWN;
-		info->sector_count = 0;
-		info->size = 0;
-		break;
-	}
-
-	/* Check 16 bits or 32 bits of ID so work on 32 or 16 bit bus. */
-	if (info->flash_id != FLASH_UNKNOWN) switch ((FPW)addr[2]) {
-
-	case (FPW)AMD_ID_LV160B:
-		info->flash_id += FLASH_AM160B;
-		info->sector_count = 35;
-		info->size = 0x00200000;
-#ifdef CFG_LOWBOOT
-		offset = 0;
-#else
-		offset = 0x00e00000;
-#endif
-		info->start[0] = (ulong)addr + offset;
-		info->start[1] = (ulong)addr + offset + 0x4000;
-		info->start[2] = (ulong)addr + offset + 0x6000;
-		info->start[3] = (ulong)addr + offset + 0x8000;
-		for (i = 4; i < info->sector_count; i++)
-		{
-			info->start[i] = (ulong)addr + offset + 0x10000 * (i-3);
-		}
-		break;
-
-	case (FPW)AMD_ID_LV065D:
-		info->flash_id += FLASH_AMDLV065D;
-		info->sector_count = 128;
-		info->size = 0x00800000;
-#ifdef CFG_LOWBOOT
-		offset = 0;
-#else
-		offset = 0x00800000;
-#endif
-		for( i = 0; i < info->sector_count; i++ )
-			info->start[i] = (ulong)addr + offset + (i * 0x10000);
-		break;				/* => 8 or 16 MB	*/
-
-	default:
-		printf ("unknown AMD device=%x ", (FPW)addr[2]);
-		info->flash_id = FLASH_UNKNOWN;
-		info->sector_count = 0;
-		info->size = 0;
-		return (0);			/* => no or unknown flash */
-	}
-
-	/* Put FLASH back in read mode */
-	flash_reset(info);
-
-	return (info->size);
-}
-
-/*-----------------------------------------------------------------------
- */
-
-int	flash_erase (flash_info_t *info, int s_first, int s_last)
-{
-	FPWV *addr;
-	int flag, prot, sect;
-	int intel = (info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL;
-	ulong start, now, last;
-	int rcode = 0;
-
-	if ((s_first < 0) || (s_first > s_last)) {
-		if (info->flash_id == FLASH_UNKNOWN) {
-			printf ("- missing\n");
-		} else {
-			printf ("- no sectors to erase\n");
-		}
-		return 1;
-	}
-
-	switch (info->flash_id & FLASH_TYPEMASK) {
-	case FLASH_AMDLV065D:
-		break;
-	case FLASH_UNKNOWN:
-	default:
-		printf ("Can't erase unknown flash type %08lx - aborted\n",
-			info->flash_id);
-		return 1;
-	}
-
-	prot = 0;
-	for (sect=s_first; sect<=s_last; ++sect) {
-		if (info->protect[sect]) {
-			prot++;
-		}
-	}
-
-	if (prot) {
-		printf ("- Warning: %d protected sectors will not be erased!\n",
-			prot);
-	} else {
-		printf ("\n");
-	}
-
-	last  = get_timer(0);
-
-	/* Start erase on unprotected sectors */
-	for (sect = s_first; sect<=s_last && rcode == 0; sect++) {
-
-		if (info->protect[sect] != 0)	/* protected, skip it */
-			continue;
-
-		/* Disable interrupts which might cause a timeout here */
-		flag = disable_interrupts();
-
-		addr = (FPWV *)(info->start[sect]);
-		if (intel) {
-			*addr = (FPW)0x00500050; /* clear status register */
-			*addr = (FPW)0x00200020; /* erase setup */
-			*addr = (FPW)0x00D000D0; /* erase confirm */
-		}
-		else {
-			/* must be AMD style if not Intel */
-			FPWV *base;		/* first address in bank */
-
-			base = (FPWV *)(info->start[0]);
-			base[FLASH_CYCLE1] = (FPW)0x00AA00AA;	/* unlock */
-			base[FLASH_CYCLE2] = (FPW)0x00550055;	/* unlock */
-			base[FLASH_CYCLE1] = (FPW)0x00800080;	/* erase mode */
-			base[FLASH_CYCLE1] = (FPW)0x00AA00AA;	/* unlock */
-			base[FLASH_CYCLE2] = (FPW)0x00550055;	/* unlock */
-			*addr = (FPW)0x00300030;	/* erase sector */
-		}
-
-		/* re-enable interrupts if necessary */
-		if (flag)
-			enable_interrupts();
-
-		start = get_timer(0);
-
-		/* wait at least 50us for AMD, 80us for Intel.
-		 * Let's wait 1 ms.
-		 */
-		udelay (1000);
-
-		while ((*addr & (FPW)0x00800080) != (FPW)0x00800080) {
-			if ((now = get_timer(start)) > CFG_FLASH_ERASE_TOUT) {
-				printf ("Timeout\n");
-
-				if (intel) {
-					/* suspend erase	*/
-					*addr = (FPW)0x00B000B0;
-				}
-
-				flash_reset(info);	/* reset to read mode */
-				rcode = 1;		/* failed */
-				break;
-			}
-
-			/* show that we're waiting */
-			if ((get_timer(last)) > CFG_HZ) {/* every second */
-				putc ('.');
-				last = get_timer(0);
-			}
-		}
-
-		/* show that we're waiting */
-		if ((get_timer(last)) > CFG_HZ) {	/* every second */
-			putc ('.');
-			last = get_timer(0);
-		}
-
-		flash_reset(info);	/* reset to read mode	*/
-	}
-
-	printf (" done\n");
-	return rcode;
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
-{
-	FPW data = 0; /* 16 or 32 bit word, matches flash bus width on MPC8XX */
-	int bytes;	  /* number of bytes to program in current word		*/
-	int left;	  /* number of bytes left to program			*/
-	int i, res;
-
-	for (left = cnt, res = 0;
-		 left > 0 && res == 0;
-		 addr += sizeof(data), left -= sizeof(data) - bytes) {
-
-		bytes = addr & (sizeof(data) - 1);
-		addr &= ~(sizeof(data) - 1);
-
-		/* combine source and destination data so can program
-		 * an entire word of 16 or 32 bits
-		 */
-		for (i = 0; i < sizeof(data); i++) {
-			data <<= 8;
-			if (i < bytes || i - bytes >= left )
-				data += *((uchar *)addr + i);
-			else
-				data += *src++;
-		}
-
-		/* write one word to the flash */
-		switch (info->flash_id & FLASH_VENDMASK) {
-		case FLASH_MAN_AMD:
-			res = write_word_amd(info, (FPWV *)addr, data);
-			break;
-		default:
-			/* unknown flash type, error! */
-			printf ("missing or unknown FLASH type\n");
-			res = 1;	/* not really a timeout, but gives error */
-			break;
-		}
-	}
-
-	return (res);
-}
-
-/*-----------------------------------------------------------------------
- * Write a word to Flash for AMD FLASH
- * A word is 16 or 32 bits, whichever the bus width of the flash bank
- * (not an individual chip) is.
- *
- * returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_word_amd (flash_info_t *info, FPWV *dest, FPW data)
-{
-	ulong start;
-	int flag;
-	int res = 0;	/* result, assume success	*/
-	FPWV *base;		/* first address in flash bank	*/
-
-	/* Check if Flash is (sufficiently) erased */
-	if ((*dest & data) != data) {
-		return (2);
-	}
-
-
-	base = (FPWV *)(info->start[0]);
-
-	/* Disable interrupts which might cause a timeout here */
-	flag = disable_interrupts();
-
-	base[FLASH_CYCLE1] = (FPW)0x00AA00AA;	/* unlock */
-	base[FLASH_CYCLE2] = (FPW)0x00550055;	/* unlock */
-	base[FLASH_CYCLE1] = (FPW)0x00A000A0;	/* selects program mode */
-
-	*dest = data;		/* start programming the data	*/
-
-	/* re-enable interrupts if necessary */
-	if (flag)
-		enable_interrupts();
-
-	start = get_timer (0);
-
-	/* data polling for D7 */
-	while (res == 0 && (*dest & (FPW)0x00800080) != (data & (FPW)0x00800080)) {
-		if (get_timer(start) > CFG_FLASH_WRITE_TOUT) {
-			*dest = (FPW)0x00F000F0;	/* reset bank */
-			res = 1;
-		}
-	}
-
-	return (res);
-}
--- a/board/emk/top5200/top5200.c
+++ b/board/emk/top5200/top5200.c
@@ -57,7 +57,7 @@ long int initdram (int board_type)
 	*(vu_long *)MPC5XXX_SDRAM_CTRL = CFG_DRAM_CONTROL | MODE_EN;
 	/* precharge all banks */
 	*(vu_long *)MPC5XXX_SDRAM_CTRL = CFG_DRAM_CONTROL | MODE_EN | SOFT_PRE;
-#if CFG_DRAM_DDR
+#ifdef CFG_DRAM_DDR
 	/* set extended mode register */
 	*(vu_short *)MPC5XXX_SDRAM_MODE = CFG_DRAM_EMODE;
 #endif
@@ -113,11 +113,15 @@ int checkboard (void)
 #if defined (CONFIG_EVAL5200)
 	puts ("Board: EMK TOP5200 on EVAL5200\n");
 #else
+#if defined (CONFIG_LITE5200)
+	puts ("Board: LITE5200\n");
+#else
 #if defined (CONFIG_MINI5200)
 	puts ("Board: EMK TOP5200 on MINI5200\n");
 #else
 	puts ("Board: EMK TOP5200\n");
 #endif
+#endif
 #endif
 	return 0;
 }
@@ -155,54 +159,11 @@ void flash_afterinit(uint bank, ulong start, ulong size)
 *****************************************************************************/
 int misc_init_r (void)
 {
+#if !defined (CONFIG_LITE5200)
 	/* read 'factory' part of EEPROM */
-	uchar buf[81];
-	uchar *p;
-	uint length;
-	uint addr;
-	uint len;
-
-	/* get length first */
-	addr = CFG_FACT_OFFSET;
-	if (eeprom_read (CFG_I2C_FACT_ADDR, addr, buf, 2)) {
-bailout:
-		printf ("cannot read factory configuration\n");
-		printf ("be sure to set ethaddr	yourself!\n");
-		return 0;
-	}
-	length = buf[0] + (buf[1] << 8);
-	addr += 2;
-
-	/* sanity check */
-	if (length < 20 || length > CFG_FACT_SIZE - 2)
-		goto bailout;
-
-	/* read lines */
-	while (length > 0) {
-		/* read one line */
-		len = length > 80 ? 80 : length;
-		if (eeprom_read (CFG_I2C_FACT_ADDR, addr, buf, len))
-			goto bailout;
-		/* mark end of buffer */
-		buf[len] = 0;
-		/* search end of line */
-		for (p = buf; *p && *p != 0x0a; p++);
-		if (!*p)
-			goto bailout;
-		*p++ = 0;
-		/* advance to next line start */
-		length -= p - buf;
-		addr += p - buf;
-		/*printf ("%s\n", buf); */
-		/* search for our specific entry */
-		if (!strncmp ((char *) buf, "[RLA/lan/Ethernet] ", 19)) {
-			setenv ("ethaddr", buf + 19);
-		} else if (!strncmp ((char *) buf, "[BOARD/SERIAL] ", 15)) {
-			setenv ("serial#", buf + 15);
-		} else if (!strncmp ((char *) buf, "[BOARD/TYPE] ", 13)) {
-			setenv ("board_id", buf + 13);
-		}
-	}
+	extern void read_factory_r (void);
+	read_factory_r ();
+#endif
 	return (0);
 }

@@ -219,3 +180,23 @@ void pci_init_board(void)
 	pci_mpc5xxx_init(&hose);
 }
 #endif
+
+/*****************************************************************************
+ * provide the PCI Reset Function
+ *****************************************************************************/
+#ifdef CFG_CMD_IDE
+#define GPIO_PSC1_4	0x01000000ul
+void ide_set_reset (int idereset)
+{
+	if (idereset) {
+		*(vu_long *) MPC5XXX_WU_GPIO_DATA &= ~GPIO_PSC1_4;
+	} else {
+		*(vu_long *) MPC5XXX_WU_GPIO_DATA |= GPIO_PSC1_4;
+	}
+
+	/* Configure PSC1_4 as GPIO output for ATA reset */
+	/* (it does not matter we do this every time) */
+	*(vu_long *) MPC5XXX_WU_GPIO_ENABLE |= GPIO_PSC1_4;
+	*(vu_long *) MPC5XXX_WU_GPIO_DIR |= GPIO_PSC1_4;
+}
+#endif
--- a/board/emk/top860/Makefile
+++ b/board/emk/top860/Makefile
@@ -25,7 +25,7 @@ include $(TOPDIR)/config.mk

 LIB	= lib$(BOARD).a

-OBJS	= $(BOARD).o flash.o
+OBJS	= $(BOARD).o ../common/flash.o ../common/vpd.o ../common/am79c874.o

 $(LIB):	.depend $(OBJS)
 	$(AR) crv $@ $(OBJS)
--- a/board/emk/top860/flash.c
+++ b/board/emk/top860/flash.c
@@ -1,489 +0,0 @@
-/*
- * (C) Copyright 2003
- * EMK Elektronik GmbH <www.emk-elektronik.de>
- * Reinhard Meyer <r.meyer@emk-elektronik.de>
- *
- * copied from the BMW Port - seems that its similiar enough
- * to be easily adaped ;) --- Well, it turned out to become a
- * merger between parts of the EMKstax Flash routines and the
- * BMW funtion frames...
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <mpc8xx.h>
-
-#define	FLASH_WORD_SIZE		unsigned short
-#define FLASH_WORD_WIDTH	(sizeof (FLASH_WORD_SIZE))
-
-flash_info_t flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips    */
-
-/*-----------------------------------------------------------------------
- * Functions
- */
-static int write_word (flash_info_t *info, ulong dest, ulong data);
-
-
-/*****************************************************************************
- * software product ID entry/exit
- *****************************************************************************/
-static void FlashProductIdMode (
-	volatile FLASH_WORD_SIZE *b,
-	int on_off)
-{
-	b[0x5555] = 0xaa;
-	b[0x2aaa] = 0x55;
-	b[0x5555] = on_off ? 0x90 : 0xf0;
-}
-
-/*****************************************************************************
- * sector erase start
- *****************************************************************************/
-static void FlashSectorErase (
-	volatile FLASH_WORD_SIZE *b,
-	volatile FLASH_WORD_SIZE *a)
-{
-	b[0x5555] = 0xaa;
-	b[0x2aaa] = 0x55;
-	b[0x5555] = 0x80;
-	b[0x5555] = 0xaa;
-	b[0x2aaa] = 0x55;
-	a[0] = 0x30;
-}
-
-/*****************************************************************************
- * program a word
- *****************************************************************************/
-static void FlashProgWord (
-	volatile FLASH_WORD_SIZE *b,
-	volatile FLASH_WORD_SIZE *a,
-	FLASH_WORD_SIZE v)
-{
-	b[0x5555] = 0xaa;
-	b[0x2aaa] = 0x55;
-	b[0x5555] = 0xa0;
-	a[0] = v;
-}
-
-/*****************************************************************************
- * reset bank, back to read mode
- *****************************************************************************/
-static void FlashReset (volatile FLASH_WORD_SIZE *b)
-{
-	b[0] = 0xf0;
-}
-
-/*****************************************************************************
- * identify FLASH chip
- * this code is a stripped version of the FlashGetType() function in EMKstax
- *****************************************************************************/
-unsigned long flash_init (void)
-{
-	volatile FLASH_WORD_SIZE * const flash = (volatile FLASH_WORD_SIZE *) CFG_FLASH_BASE;
-	FLASH_WORD_SIZE	manu, dev;
-	flash_info_t * const pflinfo = &flash_info[0];
-	int j;
-
-	/* get Id Bytes */
-	FlashProductIdMode (flash, 1);
-	manu = flash[0];
-	dev  = flash[1];
-	FlashProductIdMode (flash, 0);
-
-	pflinfo->size = 0;
-	pflinfo->sector_count = 0;
-	pflinfo->flash_id = 0xffffffff;
-	pflinfo->portwidth = FLASH_CFI_16BIT;
-	pflinfo->chipwidth = FLASH_CFI_BY16;
-
-	switch (manu&0xff)
-	{
-	case 0x01:	/* AMD */
-		pflinfo->flash_id = FLASH_MAN_AMD;
-		switch (dev&0xff)
-		{
-		case 0x49:
-			pflinfo->size = 0x00200000;
-			pflinfo->sector_count = 35;
-			pflinfo->flash_id |= FLASH_AM160B;
-			pflinfo->start[0] = CFG_FLASH_BASE;
-			pflinfo->start[1] = CFG_FLASH_BASE + 0x4000;
-			pflinfo->start[2] = CFG_FLASH_BASE + 0x6000;
-			pflinfo->start[3] = CFG_FLASH_BASE + 0x8000;
-			for (j = 4; j < 35; j++)
-			{
-				pflinfo->start[j] = CFG_FLASH_BASE + 0x00010000 * (j-3);
-			}
-			break;
-
-		case 0xf9:
-			pflinfo->size = 0x00400000;
-			pflinfo->sector_count = 71;
-			pflinfo->flash_id |= FLASH_AM320B;
-			pflinfo->start[0] = CFG_FLASH_BASE;
-			pflinfo->start[1] = CFG_FLASH_BASE + 0x4000;
-			pflinfo->start[2] = CFG_FLASH_BASE + 0x6000;
-			pflinfo->start[3] = CFG_FLASH_BASE + 0x8000;
-			for (j = 0; j < 8; j++)
-			{
-				pflinfo->start[j] = CFG_FLASH_BASE + 0x00002000 * (j);
-			}
-			for (j = 8; j < 71; j++)
-			{
-				pflinfo->start[j] = CFG_FLASH_BASE + 0x00010000 * (j-7);
-			}
-			break;
-
-		default:
-			printf ("unknown AMD dev=%x ", dev);
-			pflinfo->flash_id |= FLASH_UNKNOWN;
-		}
-		break;
-
-	default:
-		printf ("unknown manu=%x ", manu);
-	}
-	return pflinfo->size;
-}
-
-/*****************************************************************************
- * print info about a FLASH
- *****************************************************************************/
-void flash_print_info (flash_info_t *info)
-{
-	static const char	unk[] = "Unknown";
-	unsigned int		i;
-	const char			*mfct=unk,
-						*type=unk;
-
-	if(info->flash_id != FLASH_UNKNOWN)
-	{
-		switch (info->flash_id & FLASH_VENDMASK)
-		{
-		case FLASH_MAN_AMD:
-			mfct = "AMD";
-			break;
-		}
-
-		switch (info->flash_id & FLASH_TYPEMASK)
-		{
-		case FLASH_AM160B:
-			type = "AM29LV160B (16 Mbit, bottom boot sect)";
-			break;
-		case FLASH_AM320B:
-			type = "AM29LV320B (32 Mbit, bottom boot sect)";
-			break;
-		}
-	}
-
-	printf (
-		"\n  Brand: %s Type: %s\n"
-		"  Size: %lu KB in %d Sectors\n",
-		mfct,
-		type,
-		info->size >> 10,
-		info->sector_count
-		);
-
-	printf ("  Sector Start Addresses:");
-
-	for (i = 0; i < info->sector_count; i++)
-	{
-		unsigned long	size;
-		unsigned int	erased;
-		unsigned long	*flash = (unsigned long *) info->start[i];
-
-		/*
-		 * Check if whole sector is erased
-		 */
-		size =
-			(i != (info->sector_count - 1)) ?
-			(info->start[i + 1] - info->start[i]) >> 2 :
-		(info->start[0] + info->size - info->start[i]) >> 2;
-
-		for (
-			flash = (unsigned long *) info->start[i], erased = 1;
-				(flash != (unsigned long *) info->start[i] + size) && erased;
-					flash++
-			)
-			erased = *flash == ~0x0UL;
-
-		printf (
-			"%s %08lX %s %s",
-			(i % 5) ? "" : "\n   ",
-			info->start[i],
-			erased ? "E" : " ",
-			info->protect[i] ? "RO" : "  "
-			);
-	}
-
-	puts ("\n");
-	return;
-}
-
-/*****************************************************************************
- * erase one or more sectors
- *****************************************************************************/
-int	flash_erase (flash_info_t *info, int s_first, int s_last)
-{
-	volatile FLASH_WORD_SIZE	*addr = (FLASH_WORD_SIZE *)(info->start[0]);
-	int							flag,
-								prot,
-								sect,
-								l_sect;
-	ulong						start,
-								now,
-								last;
-
-	if ((s_first < 0) || (s_first > s_last))
-	{
-		if (info->flash_id == FLASH_UNKNOWN)
-		{
-			printf ("- missing\n");
-		}
-		else
-		{
-			printf ("- no sectors to erase\n");
-		}
-		return 1;
-	}
-
-	if ((info->flash_id == FLASH_UNKNOWN) ||
-		(info->flash_id > (FLASH_MAN_STM | FLASH_AMD_COMP)))
-	{
-		printf ("Can't erase unknown flash type - aborted\n");
-		return 1;
-	}
-
-	prot = 0;
-	for (sect=s_first; sect<=s_last; ++sect)
-	{
-		if (info->protect[sect])
-		{
-			prot++;
-		}
-	}
-
-	if (prot)
-	{
-		printf ("- Warning: %d protected sectors will not be erased!\n",
-			prot);
-	}
-	else
-	{
-		printf ("\n");
-	}
-
-	l_sect = -1;
-
-	/* Disable interrupts which might cause a timeout here */
-	flag = disable_interrupts();
-
-	/* Start erase on unprotected sectors */
-	for (sect = s_first; sect<=s_last; sect++)
-	{
-		if (info->protect[sect] == 0)
-		{ /* not protected */
-			FlashSectorErase ((FLASH_WORD_SIZE *)info->start[0], (FLASH_WORD_SIZE *)info->start[sect]);
-			l_sect = sect;
-		}
-	}
-
-	/* re-enable interrupts if necessary */
-	if (flag)
-		enable_interrupts();
-
-	/* wait at least 80us - let's wait 1 ms */
-	udelay (1000);
-
-	/*
-	* We wait for the last triggered sector
-	*/
-	if (l_sect < 0)
-		goto DONE;
-
-	start = get_timer (0);
-	last  = start;
-	addr = (FLASH_WORD_SIZE *)info->start[l_sect];
-	while ((addr[0] & 0x0080) != 0x0080)
-	{
-		if ((now = get_timer (start)) > CFG_FLASH_ERASE_TOUT)
-		{
-			printf ("Timeout\n");
-			return 1;
-		}
-		/* show that we're waiting */
-		if ((now - last) > 1000)
-		{  /* every second */
-			serial_putc ('.');
-			last = now;
-		}
-	}
-
-	DONE:
-	/* reset to read mode */
-	FlashReset ((FLASH_WORD_SIZE *)info->start[0]);
-
-	printf (" done\n");
-	return 0;
-}
-
-/*****************************************************************************
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- *****************************************************************************/
-int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
-{
-	ulong		cp,
-				wp,
-				data;
-	int			i,
-				l,
-				rc;
-
-	wp = (addr & ~(FLASH_WORD_WIDTH-1));   /* get lower word aligned address */
-
-	/*
-	 * handle unaligned start bytes, if there are...
-	 */
-	if ((l = addr - wp) != 0)
-	{
-		data = 0;
-
-		/* get the current before the new data into our data word */
-		for (i=0, cp=wp; i<l; ++i, ++cp)
-		{
-			data = (data << 8) | (*(uchar *)cp);
-		}
-
-		/* now merge the to be programmed values */
-		for (; i<4 && cnt>0; ++i, ++cp, --cnt)
-		{
-			data = (data << 8) | *src++;
-		}
-
-		/* get the current after the new data into our data word */
-		for (; cnt==0 && i<FLASH_WORD_WIDTH; ++i, ++cp)
-		{
-			data = (data << 8) | (*(uchar *)cp);
-		}
-
-		/* now write the combined word */
-		if ((rc = write_word (info, wp, data)) != 0)
-		{
-			return (rc);
-		}
-		wp += FLASH_WORD_WIDTH;
-	}
-
-	/*
-	 * handle word aligned part
-	 */
-	while (cnt >= FLASH_WORD_WIDTH)
-	{
-		data = 0;
-		for (i=0; i<FLASH_WORD_WIDTH; ++i)
-		{
-			data = (data << 8) | *src++;
-		}
-		if ((rc = write_word (info, wp, data)) != 0)
-		{
-			return (rc);
-		}
-		wp  += FLASH_WORD_WIDTH;
-		cnt -= FLASH_WORD_WIDTH;
-	}
-
-	if (cnt == 0)
-	{
-		return (0);
-	}
-
-	/*
-	 * handle unaligned tail bytes, if there are...
-	 */
-	data = 0;
-
-	/* now merge the to be programmed values */
-	for (i=0, cp=wp; i<FLASH_WORD_WIDTH && cnt>0; ++i, ++cp)
-	{
-		data = (data << 8) | *src++;
-		--cnt;
-	}
-
-	/* get the current after the new data into our data word */
-	for (; i<FLASH_WORD_WIDTH; ++i, ++cp)
-	{
-		data = (data << 8) | (*(uchar *)cp);
-	}
-
-	/* now write the combined word */
-	return (write_word (info, wp, data));
-}
-
-/*****************************************************************************
- * Write a word to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- *****************************************************************************/
-static int write_word (flash_info_t *info, ulong dest, ulong data)
-{
-	volatile FLASH_WORD_SIZE	*addr2 = (FLASH_WORD_SIZE *)info->start[0];
-	volatile FLASH_WORD_SIZE	*dest2 = (FLASH_WORD_SIZE *)dest;
-	FLASH_WORD_SIZE				data2 = data;
-	ulong						start;
-	int							flag;
-
-	/* Check if Flash is (sufficiently) erased */
-	if ((*dest2 & data2) != data2)
-	{
-		return (2);
-	}
-
-	/* Disable interrupts which might cause a timeout here */
-	flag = disable_interrupts ();
-
-	FlashProgWord (addr2, dest2, data2);
-
-	/* re-enable interrupts if necessary */
-	if (flag)
-		enable_interrupts ();
-
-	/* data polling for D7 */
-	start = get_timer (0);
-	while ((*dest2 & 0x0080) != (data2 & 0x0080))
-	{
-		if (get_timer (start) > CFG_FLASH_WRITE_TOUT)
-		{
-			return (1);
-		}
-	}
-
-	return (0);
-}
-
-/*-----------------------------------------------------------------------
- */
--- a/board/emk/top860/top860.c
+++ b/board/emk/top860/top860.c
@@ -119,6 +119,20 @@ long int initdram (int board_type)
 	return -(memctl->memc_or2 & 0xffff0000);
 }

+/*****************************************************************************
+ * prepare for FLASH detection
+ *****************************************************************************/
+void flash_preinit(void)
+{
+}
+
+/*****************************************************************************
+ * finalize FLASH setup
+ *****************************************************************************/
+void flash_afterinit(uint bank, ulong start, ulong size)
+{
+}
+
 /*****************************************************************************
 * otherinits after RAM is there and we are relocated to RAM
 * note: though this is an int function, nobody cares for the result!
@@ -126,52 +140,8 @@ long int initdram (int board_type)
 int misc_init_r (void)
 {
 	/* read 'factory' part of EEPROM */
-	uchar buf[81];
-	uchar *p;
-	uint length;
-	uint addr;
-	uint len;
+	extern void read_factory_r (void);
+	read_factory_r ();

-	/* get length first */
-	addr = CFG_FACT_OFFSET;
-	if (eeprom_read (CFG_I2C_FACT_ADDR, addr, buf, 2)) {
-	  bailout:
-		printf ("cannot read factory configuration\n");
-		printf ("be sure to set ethaddr	yourself!\n");
-		return 0;
-	}
-	length = buf[0] + (buf[1] << 8);
-	addr += 2;
-
-	/* sanity check */
-	if (length < 20 || length > CFG_FACT_SIZE - 2)
-		goto bailout;
-
-	/* read lines */
-	while (length > 0) {
-		/* read one line */
-		len = length > 80 ? 80 : length;
-		if (eeprom_read (CFG_I2C_FACT_ADDR, addr, buf, len))
-			goto bailout;
-		/* mark end of buffer */
-		buf[len] = 0;
-		/* search end of line */
-		for (p = buf; *p && *p != 0x0a; p++);
-		if (!*p)
-			goto bailout;
-		*p++ = 0;
-		/* advance to next line start */
-		length -= p - buf;
-		addr += p - buf;
-		/*printf ("%s\n", buf); */
-		/* search for our specific entry */
-		if (!strncmp ((char *) buf, "[RLA/lan/Ethernet] ", 19)) {
-			setenv ("ethaddr", buf + 19);
-		} else if (!strncmp ((char *) buf, "[BOARD/SERIAL] ", 15)) {
-			setenv ("serial#", buf + 15);
-		} else if (!strncmp ((char *) buf, "[BOARD/TYPE] ", 13)) {
-			setenv ("board_id", buf + 13);
-		}
-	}
 	return (0);
 }
--- a/board/esd/ar405/fpgadata.c
+++ b/board/esd/ar405/fpgadata.c
@@ -2747,4 +2747,4 @@
 0x05,0x02,0x02,0x03,0x02,0x02,0x03,0x02,0x02,0x01,0x07,0x03,0x02,0x02,0x02,0x04,
 0x02,0x01,0x04,0x02,0x01,0x02,0x01,0x02,0x01,0x01,0xe5,0x05,0x04,0x03,0x07,0xe5,
 0xe5,0x03,0x04,0x04,0x0b,0x02,0xe5,0x01,0xe5,0x01,0xe5,0xff,0xff,0xff,0xff,0xff,
- 0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,
+ 0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,0xff,
--- a/board/evb64260/sdram_init.c
+++ b/board/evb64260/sdram_init.c
@@ -341,11 +341,7 @@ static int setup_sdram_common (sdram_info_t info[2])
 			tras_clocks = info[0].tras_clocks;
 		if (!info[0].registered)
 			registered = 0;
-		if (info[0].ecc != 2indent: Standard input:491: Warning:old style assignment ambiguity in "=*".  Assuming "= *"
-
-indent: Standard input:492: Warning:old style assignment ambiguity in "=*".  Assuming "= *"
-
-)
+		if (info[0].ecc != 2)
 			ecc = 0;
 	}

--- a/board/gcplus/Makefile
+++ b/board/gcplus/Makefile
@@ -0,0 +1,49 @@
+#
+# (C) Copyright 2000
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# 2003 (c) MontaVista Software, Inc.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	:= gcplus.o flash.o
+SOBJS	:= memsetup.o
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) crv $@ $(OBJS) $(SOBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+-include .depend
+
+#########################################################################
--- a/board/gcplus/config.mk
+++ b/board/gcplus/config.mk
@@ -0,0 +1,13 @@
+#
+# ADS GCPlus board with SA1110 cpu
+#
+# The ADS GCPlus has 2 banks of 16 MiB SDRAM
+#
+# We use the ADS GCPlus Linux boot ROM to load U-Boot into SDRAM
+# at c020'0000 and then move ourself to c8f0'0000. Basically, just
+# install the U-Boot binary as you would the Linux zImage and then
+# reap the benfits of more convenient Linux development cycles, i.e.
+# bootp;tftp;bootm, repeat, etc.,.
+#
+
+TEXT_BASE = 0xc8f00000
--- a/board/gcplus/flash.c
+++ b/board/gcplus/flash.c
@@ -0,0 +1,440 @@
+/*
+ * (C) Copyright 2001
+ * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net
+ *
+ * (C) Copyright 2001
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * 2003 (c) MontaVista Software, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <linux/byteorder/swab.h>
+
+flash_info_t flash_info[CFG_MAX_FLASH_BANKS];	/* info for FLASH chips */
+
+/* Board support for 1 or 2 flash devices */
+#define FLASH_PORT_WIDTH32
+#undef FLASH_PORT_WIDTH16
+
+#ifdef FLASH_PORT_WIDTH16
+#define FLASH_PORT_WIDTH		ushort
+#define FLASH_PORT_WIDTHV		vu_short
+#define SWAP(x)				__swab16(x)
+#else
+#define FLASH_PORT_WIDTH		ulong
+#define FLASH_PORT_WIDTHV		vu_long
+#define SWAP(x)				__swab32(x)
+#endif
+
+#define FPW				FLASH_PORT_WIDTH
+#define FPWV				FLASH_PORT_WIDTHV
+
+#define mb() __asm__ __volatile__ ("" : : : "memory")
+
+/*-----------------------------------------------------------------------
+ * Functions
+ */
+static ulong flash_get_size(FPW * addr, flash_info_t * info);
+static int write_data(flash_info_t * info, ulong dest, FPW data);
+static void flash_get_offsets(ulong base, flash_info_t * info);
+void inline spin_wheel(void);
+
+/*-----------------------------------------------------------------------
+ */
+
+unsigned long
+flash_init(void)
+{
+	int i;
+	ulong size = 0;
+
+	for (i = 0; i < CFG_MAX_FLASH_BANKS; i++) {
+		switch (i) {
+		case 0:
+			flash_get_size((FPW *) PHYS_FLASH_1, &flash_info[i]);
+			flash_get_offsets(PHYS_FLASH_1, &flash_info[i]);
+			break;
+		default:
+			panic("configured too many flash banks!\n");
+			break;
+		}
+		size += flash_info[i].size;
+	}
+
+	/* Protect monitor and environment sectors
+	 */
+	flash_protect(FLAG_PROTECT_SET,
+		      CFG_FLASH_BASE,
+		      CFG_FLASH_BASE + monitor_flash_len - 1, &flash_info[0]);
+
+	flash_protect(FLAG_PROTECT_SET,
+		      CFG_ENV_ADDR,
+		      CFG_ENV_ADDR + CFG_ENV_SIZE - 1, &flash_info[0]);
+
+	return size;
+}
+
+/*-----------------------------------------------------------------------
+ */
+static void
+flash_get_offsets(ulong base, flash_info_t * info)
+{
+	int i;
+
+	if (info->flash_id == FLASH_UNKNOWN) {
+		return;
+	}
+
+	if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL) {
+		for (i = 0; i < info->sector_count; i++) {
+			info->start[i] = base + (i * PHYS_FLASH_SECT_SIZE);
+			info->protect[i] = 0;
+		}
+	}
+}
+
+/*-----------------------------------------------------------------------
+ */
+void
+flash_print_info(flash_info_t * info)
+{
+	int i;
+
+	if (info->flash_id == FLASH_UNKNOWN) {
+		printf("missing or unknown FLASH type\n");
+		return;
+	}
+
+	switch (info->flash_id & FLASH_VENDMASK) {
+	case FLASH_MAN_INTEL:
+		printf("INTEL ");
+		break;
+	default:
+		printf("Unknown Vendor ");
+		break;
+	}
+
+	switch (info->flash_id & FLASH_TYPEMASK) {
+	case FLASH_28F128J3A:
+		printf("28F128J3A\n");
+		break;
+	case FLASH_28F640J5:
+		printf("28F640J5\n");
+		break;
+	default:
+		printf("Unknown Chip Type\n");
+		break;
+	}
+
+	printf("  Size: %ld MB in %d Sectors\n",
+	       info->size >> 20, info->sector_count);
+
+	printf("  Sector Start Addresses:");
+	for (i = 0; i < info->sector_count; ++i) {
+		if ((i % 5) == 0)
+			printf("\n   ");
+		printf(" %08lX%s",
+		       info->start[i], info->protect[i] ? " (RO)" : "     ");
+	}
+	printf("\n");
+	return;
+}
+
+/*
+ * The following code cannot be run from FLASH!
+ */
+static ulong
+flash_get_size(FPW * addr, flash_info_t * info)
+{
+	volatile FPW value;
+	/* Write auto select command: read Manufacturer ID */
+	addr[0x5555] = (FPW) 0x00AA00AA;
+	addr[0x2AAA] = (FPW) 0x00550055;
+	addr[0x5555] = (FPW) 0x00900090;
+
+	mb();
+	value = addr[0];
+
+	switch (value) {
+
+	case (FPW) INTEL_MANUFACT:
+		info->flash_id = FLASH_MAN_INTEL;
+		break;
+
+	default:
+		info->flash_id = FLASH_UNKNOWN;
+		info->sector_count = 0;
+		info->size = 0;
+		addr[0] = (FPW) 0x00FF00FF;	/* restore read mode */
+		return (0);	/* no or unknown flash  */
+	}
+
+	mb();
+	value = addr[1];	/* device ID            */
+	switch (value) {
+	case (FPW) INTEL_ID_28F128J3A:
+		info->flash_id += FLASH_28F128J3A;
+		info->sector_count = 128;
+		info->size = 0x02000000;
+		break;		/* => 16 MB     */
+	case (FPW) INTEL_ID_28F640J5:
+		info->flash_id += FLASH_28F640J5;
+		info->sector_count = 64;
+		info->size = 0x01000000;
+		break;		/* => 16 MB     */
+
+	default:
+		info->flash_id = FLASH_UNKNOWN;
+		break;
+	}
+
+	if (info->sector_count > CFG_MAX_FLASH_SECT) {
+		printf("** ERROR: sector count %d > max (%d) **\n",
+		       info->sector_count, CFG_MAX_FLASH_SECT);
+		info->sector_count = CFG_MAX_FLASH_SECT;
+	}
+
+	addr[0] = (FPW) 0x00FF00FF;	/* restore read mode */
+
+	return (info->size);
+}
+
+/*-----------------------------------------------------------------------
+ */
+
+int
+flash_erase(flash_info_t * info, int s_first, int s_last)
+{
+	int flag, prot, sect;
+	ulong type, start, last;
+	int rcode = 0;
+
+	if ((s_first < 0) || (s_first > s_last)) {
+		if (info->flash_id == FLASH_UNKNOWN) {
+			printf("- missing\n");
+		} else {
+			printf("- no sectors to erase\n");
+		}
+		return 1;
+	}
+
+	type = (info->flash_id & FLASH_VENDMASK);
+	if ((type != FLASH_MAN_INTEL)) {
+		printf("Can't erase unknown flash type %08lx - aborted\n",
+		       info->flash_id);
+		return 1;
+	}
+
+	prot = 0;
+	for (sect = s_first; sect <= s_last; ++sect) {
+		if (info->protect[sect]) {
+			prot++;
+		}
+	}
+
+	if (prot) {
+		printf("- Warning: %d protected sectors will not be erased!\n",
+		       prot);
+	} else {
+		printf("\n");
+	}
+
+	start = get_timer(0);
+	last = start;
+
+	/* Disable interrupts which might cause a timeout here */
+	flag = disable_interrupts();
+
+	/* Start erase on unprotected sectors */
+	for (sect = s_first; sect <= s_last; sect++) {
+		if (info->protect[sect] == 0) {	/* not protected */
+			FPWV *addr = (FPWV *) (info->start[sect]);
+			FPW status;
+
+			printf("Erasing sector %2d ... ", sect);
+
+			/* arm simple, non interrupt dependent timer */
+			reset_timer_masked();
+
+			*addr = (FPW) 0x00500050;	/* clear status register */
+			*addr = (FPW) 0x00200020;	/* erase setup */
+			*addr = (FPW) 0x00D000D0;	/* erase confirm */
+
+			while (((status =
+				 *addr) & (FPW) 0x00800080) !=
+			       (FPW) 0x00800080) {
+				if (get_timer_masked() > CFG_FLASH_ERASE_TOUT) {
+					printf("Timeout\n");
+					*addr = (FPW) 0x00B000B0;	/* suspend erase         */
+					*addr = (FPW) 0x00FF00FF;	/* reset to read mode */
+					rcode = 1;
+					break;
+				}
+			}
+
+			*addr = (FPW) 0x00500050;	/* clear status register cmd.   */
+			*addr = (FPW) 0x00FF00FF;	/* resest to read mode          */
+
+			printf(" done\n");
+		}
+	}
+	return rcode;
+}
+
+/*-----------------------------------------------------------------------
+ * Copy memory to flash, returns:
+ * 0 - OK
+ * 1 - write timeout
+ * 2 - Flash not erased
+ * 4 - Flash not identified
+ */
+
+int
+write_buff(flash_info_t * info, uchar * src, ulong addr, ulong cnt)
+{
+	ulong cp, wp;
+	FPW data;
+	int count, i, l, rc, port_width;
+
+	if (info->flash_id == FLASH_UNKNOWN) {
+		return 4;
+	}
+/* get lower word aligned address */
+#ifdef FLASH_PORT_WIDTH16
+	wp = (addr & ~1);
+	port_width = 2;
+#else
+	wp = (addr & ~3);
+	port_width = 4;
+#endif
+
+	/*
+	 * handle unaligned start bytes
+	 */
+	if ((l = addr - wp) != 0) {
+		data = 0;
+		for (i = 0, cp = wp; i < l; ++i, ++cp) {
+			data = (data << 8) | (*(uchar *) cp);
+		}
+		for (; i < port_width && cnt > 0; ++i) {
+			data = (data << 8) | *src++;
+			--cnt;
+			++cp;
+		}
+		for (; cnt == 0 && i < port_width; ++i, ++cp) {
+			data = (data << 8) | (*(uchar *) cp);
+		}
+
+		if ((rc = write_data(info, wp, SWAP(data))) != 0) {
+			return (rc);
+		}
+		wp += port_width;
+	}
+
+	/*
+	 * handle word aligned part
+	 */
+	count = 0;
+	while (cnt >= port_width) {
+		data = 0;
+		for (i = 0; i < port_width; ++i) {
+			data = (data << 8) | *src++;
+		}
+		if ((rc = write_data(info, wp, SWAP(data))) != 0) {
+			return (rc);
+		}
+		wp += port_width;
+		cnt -= port_width;
+		if (count++ > 0x800) {
+			spin_wheel();
+			count = 0;
+		}
+	}
+
+	if (cnt == 0) {
+		return (0);
+	}
+
+	/*
+	 * handle unaligned tail bytes
+	 */
+	data = 0;
+	for (i = 0, cp = wp; i < port_width && cnt > 0; ++i, ++cp) {
+		data = (data << 8) | *src++;
+		--cnt;
+	}
+	for (; i < port_width; ++i, ++cp) {
+		data = (data << 8) | (*(uchar *) cp);
+	}
+
+	return (write_data(info, wp, SWAP(data)));
+}
+
+/*-----------------------------------------------------------------------
+ * Write a word or halfword to Flash, returns:
+ * 0 - OK
+ * 1 - write timeout
+ * 2 - Flash not erased
+ */
+static int
+write_data(flash_info_t * info, ulong dest, FPW data)
+{
+	FPWV *addr = (FPWV *) dest;
+	ulong status;
+	int flag;
+
+	/* Check if Flash is (sufficiently) erased */
+	if ((*addr & data) != data) {
+		printf("not erased at %08lX (%lX)\n", (ulong) addr, *addr);
+		return (2);
+	}
+	/* Disable interrupts which might cause a timeout here */
+	flag = disable_interrupts();
+
+	*addr = (FPW) 0x00400040;	/* write setup */
+	*addr = data;
+
+	/* arm simple, non interrupt dependent timer */
+	reset_timer_masked();
+
+	/* wait while polling the status register */
+	while (((status = *addr) & (FPW) 0x00800080) != (FPW) 0x00800080) {
+		if (get_timer_masked() > CFG_FLASH_WRITE_TOUT) {
+			*addr = (FPW) 0x00FF00FF;	/* restore read mode */
+			return (1);
+		}
+	}
+
+	*addr = (FPW) 0x00FF00FF;	/* restore read mode */
+
+	return (0);
+}
+
+void inline
+spin_wheel(void)
+{
+	static int p = 0;
+	static char w[] = "\\/-";
+
+	printf("\010%c", w[p]);
+	(++p == 3) ? (p = 0) : 0;
+}
--- a/board/gcplus/gcplus.c
+++ b/board/gcplus/gcplus.c
@@ -0,0 +1,73 @@
+/*
+ * (C) Copyright 2002
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Marius Groeger <mgroeger@sysgo.de>
+ *
+ * 2003-2004 (c) MontaVista Software, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <SA-1100.h>
+/* ------------------------------------------------------------------------- */
+
+/*
+ * Miscelaneous platform dependent initialisations
+ */
+
+int
+board_init(void)
+{
+	DECLARE_GLOBAL_DATA_PTR;
+
+	gd->bd->bi_arch_number = 29;	/* ADS GraphicsClientPlus Board */
+
+	gd->bd->bi_boot_params = 0xc000003c; /* Weird address? */
+
+	/* Most of the ADS GCPlus I/O is connected to Static nCS2.
+	 * So I'm brute forcing nCS2 timiming here for worst case.
+	 */
+	MSC1 &= ~0xFFFF;
+	MSC1 |= 0x8649;
+
+	/* Nothing is connected to Static nCS4 or nCS5. But I'm using
+	 * nCS4 as a paranoia safe guard to force nCS2, nOE; nWE high
+	 * after accessing I/O via (non-VLIO) nCS2. What can I say, I'm
+	 * paranoid and lack decent tools to alleviate my fear. I sure
+	 * do wish I had a logic analyzer. : (
+	 */
+
+	MSC2 =  0xfff9fff9;
+
+	return 0;
+}
+
+int
+dram_init(void)
+{
+	DECLARE_GLOBAL_DATA_PTR;
+
+	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
+	gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
+	gd->bd->bi_dram[1].size = PHYS_SDRAM_2_SIZE;
+
+	return (0);
+}
--- a/board/gcplus/memsetup.S
+++ b/board/gcplus/memsetup.S
@@ -0,0 +1,77 @@
+/*
+ * Memory Setup stuff - taken from blob memsetup.S
+ *
+ * Copyright (C) 1999 2000 2001 Erik Mouw (J.A.K.Mouw@its.tudelft.nl) and
+ *                     Jan-Derk Bakker (J.D.Bakker@its.tudelft.nl)
+ * 2003-2004 (c) MontaVista Software, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+
+#include "config.h"
+#include "version.h"
+
+
+	.globl	memsetup
+memsetup:
+	/* The ADS GC+ for Linux Boot Rom Ver. 1.73 does memory init for us.
+	 * However the darn thing leaves the MMU enabled before handing control
+	 * over to us. So we need to disable the MMU and we use memsetup
+	 * to do it.
+	 */
+
+@ The following code segment was borrowed with gratitude from:
+@	linux-2.4.19-rmk7/arch/arm/boot/compressed/head-sa1100.S
+
+	@ Data cache might be active.
+	@ Be sure to flush kernel binary out of the cache,
+	@ whatever state it is, before it is turned off.
+	@ This is done by fetching through currently executed
+	@ memory to be sure we hit the same cache.
+	bic	r2, pc, #0x1f
+	add	r3, r2, #0x4000		@ 16 kb is quite enough...
+1:	ldr	r0, [r2], #32
+	teq	r2, r3
+	bne	1b
+	mcr	p15, 0, r0, c7, c10, 4	@ drain WB
+	mcr	p15, 0, r0, c7, c7, 0	@ flush I & D caches
+
+	@ disabling MMU and caches
+	mrc	p15, 0, r0, c1, c0, 0	@ read control reg
+	bic	r0, r0, #0x0d		@ clear WB, DC, MMU
+	bic	r0, r0, #0x1000		@ clear Icache
+	mcr	p15, 0, r0, c1, c0, 0
+
+	nop
+	nop
+	nop
+	nop
+	nop
+
+	b	2f
+2:
+	nop
+	nop
+	nop
+	nop
+	nop
+
+
+	mov	pc, lr
--- a/board/gcplus/u-boot.lds
+++ b/board/gcplus/u-boot.lds
@@ -0,0 +1,57 @@
+/*
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ * 2003 (c) MontaVista Software, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+	. = 0x00000000;
+
+	. = ALIGN(4);
+	.text      :
+	{
+		cpu/sa1100/start.o	(.text)
+		*(.text)
+	}
+
+	. = ALIGN(4);
+	.rodata : { *(.rodata) }
+
+	. = ALIGN(4);
+	.data : { *(.data) }
+
+	. = ALIGN(4);
+	.got : { *(.got) }
+
+
+	__u_boot_cmd_start = .;
+	.u_boot_cmd : { *(.u_boot_cmd) }
+	__u_boot_cmd_end = .;
+
+	. = ALIGN(4);
+	__bss_start = .;
+	.bss : { *(.bss) }
+	_end = .;
+}
--- a/board/icecube/icecube.c
+++ b/board/icecube/icecube.c
@@ -54,16 +54,16 @@ static void sdram_start (int hi_addr)
 	*(vu_long *)MPC5XXX_SDRAM_CTRL = 0xd04f0002 | hi_addr_bit;
 	/* set mode register */
 #if defined(CONFIG_MPC5200)
-	*(vu_long *)MPC5XXX_SDRAM_MODE = 0x408d0000;
+	*(vu_long *)MPC5XXX_SDRAM_MODE = 0x00cd0000;
 #elif defined(CONFIG_MGT5100)
 	*(vu_long *)MPC5XXX_SDRAM_MODE = 0x008d0000;
 #endif
-	/* precharge all banks */
-	*(vu_long *)MPC5XXX_SDRAM_CTRL = 0xd04f0002 | hi_addr_bit;
+	/* auto refresh */
+	*(vu_long *)MPC5XXX_SDRAM_CTRL = 0xd04f0004 | hi_addr_bit;
 	/* auto refresh */
 	*(vu_long *)MPC5XXX_SDRAM_CTRL = 0xd04f0004 | hi_addr_bit;
 	/* set mode register */
-	*(vu_long *)MPC5XXX_SDRAM_MODE = 0x008d0000;
+	*(vu_long *)MPC5XXX_SDRAM_MODE = 0x00cd0000;
 	/* normal operation */
 	*(vu_long *)MPC5XXX_SDRAM_CTRL = 0x504f0000 | hi_addr_bit;
 #endif
@@ -93,8 +93,8 @@ long int initdram (int board_type)
 	*(vu_long *)MPC5XXX_CDM_PORCFG = 0x10000000;
 #else
 	/* setup config registers */
-	*(vu_long *)MPC5XXX_SDRAM_CONFIG1 = 0xc2233a00;
-	*(vu_long *)MPC5XXX_SDRAM_CONFIG2 = 0x88b70004;
+	*(vu_long *)MPC5XXX_SDRAM_CONFIG1 = 0xd2322800;
+	*(vu_long *)MPC5XXX_SDRAM_CONFIG2 = 0x8ad70000;
 #endif

 #elif defined(CONFIG_MGT5100)
@@ -207,3 +207,28 @@ void pci_init_board(void)
 	pci_mpc5xxx_init(&hose);
 }
 #endif
+
+#if defined (CFG_CMD_IDE) && defined (CONFIG_IDE_RESET)
+
+#define GPIO_PSC1_4	0x01000000UL
+
+void init_ide_reset (void)
+{
+	debug ("init_ide_reset\n");
+
+    	/* Configure PSC1_4 as GPIO output for ATA reset */
+	*(vu_long *) MPC5XXX_WU_GPIO_ENABLE |= GPIO_PSC1_4;
+	*(vu_long *) MPC5XXX_WU_GPIO_DIR    |= GPIO_PSC1_4;
+}
+
+void ide_set_reset (int idereset)
+{
+	debug ("ide_reset(%d)\n", idereset);
+
+	if (idereset) {
+		*(vu_long *) MPC5XXX_WU_GPIO_DATA &= ~GPIO_PSC1_4;
+	} else {
+		*(vu_long *) MPC5XXX_WU_GPIO_DATA |=  GPIO_PSC1_4;
+	}
+}
+#endif /* defined (CFG_CMD_IDE) && defined (CONFIG_IDE_RESET) */
--- a/board/incaip/memsetup.S
+++ b/board/incaip/memsetup.S
@@ -185,8 +185,10 @@ sdram_init:

 	li	t1, MC_MODUL_BASE

+#if 0
 	/* Disable memory controller before changing any of its registers */
 	sw	zero, MC_CTRLENA(t1)
+#endif

 	li	t2, 100000000
 	beq	a0, t2, 1f
--- a/board/integratorap/Makefile
+++ b/board/integratorap/Makefile
@@ -0,0 +1,51 @@
+#
+# (C) Copyright 2000-2004
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# (C) Copyright 2004
+# ARM Ltd.
+# Philippe Robin, <philippe.robin@arm.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	:= integratorap.o flash.o
+SOBJS	:= platform.o
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) crv $@ $^
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+-include .depend
+
+#########################################################################
--- a/board/integratorap/config.mk
+++ b/board/integratorap/config.mk
@@ -0,0 +1,5 @@
+#
+# image should be loaded at 0x01000000
+#
+
+TEXT_BASE = 0x01000000
--- a/board/integratorap/flash.c
+++ b/board/integratorap/flash.c
@@ -0,0 +1,473 @@
+/*
+ * (C) Copyright 2001
+ * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net
+ *
+ * (C) Copyright 2001-2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * (C) Copyright 2003
+ * Texas Instruments, <www.ti.com>
+ * Kshitij Gupta <Kshitij@ti.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <linux/byteorder/swab.h>
+
+#define PHYS_FLASH_SECT_SIZE	0x00020000	/* 256 KB sectors (x2) */
+flash_info_t flash_info[CFG_MAX_FLASH_BANKS];	/* info for FLASH chips    */
+
+/* Board support for 1 or 2 flash devices */
+#undef FLASH_PORT_WIDTH32
+#define FLASH_PORT_WIDTH16
+
+#ifdef FLASH_PORT_WIDTH16
+#define FLASH_PORT_WIDTH		ushort
+#define FLASH_PORT_WIDTHV		vu_short
+#define SWAP(x)			__swab16(x)
+#else
+#define FLASH_PORT_WIDTH		ulong
+#define FLASH_PORT_WIDTHV		vu_long
+#define SWAP(x)			__swab32(x)
+#endif
+
+#define FPW	FLASH_PORT_WIDTH
+#define FPWV	FLASH_PORT_WIDTHV
+
+#define mb() __asm__ __volatile__ ("" : : : "memory")
+
+
+/* Flash Organization Structure */
+typedef struct OrgDef {
+	unsigned int sector_number;
+	unsigned int sector_size;
+} OrgDef;
+
+
+/* Flash Organizations */
+OrgDef OrgIntel_28F256L18T[] = {
+	{4, 32 * 1024},				/* 4 * 32kBytes sectors */
+	{255, 128 * 1024},			/* 255 * 128kBytes sectors */
+};
+
+
+/*-----------------------------------------------------------------------
+ * Functions
+ */
+unsigned long flash_init (void);
+static ulong flash_get_size (FPW * addr, flash_info_t * info);
+static int write_data (flash_info_t * info, ulong dest, FPW data);
+static void flash_get_offsets (ulong base, flash_info_t * info);
+void inline spin_wheel (void);
+void flash_print_info (flash_info_t * info);
+void flash_unprotect_sectors (FPWV * addr);
+int flash_erase (flash_info_t * info, int s_first, int s_last);
+int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt);
+
+/*-----------------------------------------------------------------------
+ */
+
+unsigned long flash_init (void)
+{
+	int i;
+	ulong size = 0;
+	for (i = 0; i < CFG_MAX_FLASH_BANKS; i++) {
+		switch (i) {
+		case 0:
+			flash_get_size ((FPW *) PHYS_FLASH_1, &flash_info[i]);
+			flash_get_offsets (PHYS_FLASH_1, &flash_info[i]);
+			break;
+		default:
+			panic ("configured too many flash banks!\n");
+			break;
+		}
+		size += flash_info[i].size;
+	}
+
+	/* Protect monitor and environment sectors
+	 */
+	flash_protect (FLAG_PROTECT_SET,
+			CFG_FLASH_BASE,
+			CFG_FLASH_BASE + monitor_flash_len - 1, &flash_info[0]);
+
+	return size;
+}
+
+/*-----------------------------------------------------------------------
+ */
+static void flash_get_offsets (ulong base, flash_info_t * info)
+{
+	int i;
+	OrgDef *pOrgDef;
+
+	pOrgDef = OrgIntel_28F256L18T;
+	if (info->flash_id == FLASH_UNKNOWN) {
+		return;
+	}
+
+	if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL) {
+		for (i = 0; i < info->sector_count; i++) {
+			if (i > 255) {
+				info->start[i] = base + (i * 0x8000);
+				info->protect[i] = 0;
+			} else {
+				info->start[i] = base +
+						(i * PHYS_FLASH_SECT_SIZE);
+				info->protect[i] = 0;
+			}
+		}
+	}
+}
+
+/*-----------------------------------------------------------------------
+ */
+void flash_print_info (flash_info_t * info)
+{
+	int i;
+
+	if (info->flash_id == FLASH_UNKNOWN) {
+		printf ("missing or unknown FLASH type\n");
+		return;
+	}
+
+	switch (info->flash_id & FLASH_VENDMASK) {
+	case FLASH_MAN_INTEL:
+		printf ("INTEL ");
+		break;
+	default:
+		printf ("Unknown Vendor ");
+		break;
+	}
+
+	switch (info->flash_id & FLASH_TYPEMASK) {
+	case FLASH_28F256L18T:
+		printf ("FLASH 28F256L18T\n");
+		break;
+	default:
+		printf ("Unknown Chip Type\n");
+		break;
+	}
+
+	printf ("  Size: %ld MB in %d Sectors\n",
+			info->size >> 20, info->sector_count);
+
+	printf ("  Sector Start Addresses:");
+	for (i = 0; i < info->sector_count; ++i) {
+		if ((i % 5) == 0)
+			printf ("\n   ");
+		printf (" %08lX%s",
+			info->start[i], info->protect[i] ? " (RO)" : "     ");
+	}
+	printf ("\n");
+	return;
+}
+
+/*
+ * The following code cannot be run from FLASH!
+ */
+static ulong flash_get_size (FPW * addr, flash_info_t * info)
+{
+	volatile FPW value;
+
+	/* Write auto select command: read Manufacturer ID */
+	addr[0x5555] = (FPW) 0x00AA00AA;
+	addr[0x2AAA] = (FPW) 0x00550055;
+	addr[0x5555] = (FPW) 0x00900090;
+
+	mb ();
+	value = addr[0];
+
+	switch (value) {
+
+	case (FPW) INTEL_MANUFACT:
+		info->flash_id = FLASH_MAN_INTEL;
+		break;
+
+	default:
+		info->flash_id = FLASH_UNKNOWN;
+		info->sector_count = 0;
+		info->size = 0;
+		addr[0] = (FPW) 0x00FF00FF;	/* restore read mode */
+		return (0);		/* no or unknown flash  */
+	}
+
+	mb ();
+	value = addr[1];	/* device ID        */
+	switch (value) {
+
+	case (FPW) (INTEL_ID_28F256L18T):
+		info->flash_id += FLASH_28F256L18T;
+		info->sector_count = 259;
+		info->size = 0x02000000;
+		break;			/* => 32 MB     */
+
+	default:
+		info->flash_id = FLASH_UNKNOWN;
+		break;
+	}
+
+	if (info->sector_count > CFG_MAX_FLASH_SECT) {
+		printf ("** ERROR: sector count %d > max (%d) **\n",
+				info->sector_count, CFG_MAX_FLASH_SECT);
+		info->sector_count = CFG_MAX_FLASH_SECT;
+	}
+
+	addr[0] = (FPW) 0x00FF00FF;	/* restore read mode */
+
+	return (info->size);
+}
+
+
+/* unprotects a sector for write and erase
+ * on some intel parts, this unprotects the entire chip, but it
+ * wont hurt to call this additional times per sector...
+ */
+void flash_unprotect_sectors (FPWV * addr)
+{
+#define PD_FINTEL_WSMS_READY_MASK    0x0080
+
+	*addr = (FPW) 0x00500050;	/* clear status register */
+
+	/* this sends the clear lock bit command */
+	*addr = (FPW) 0x00600060;
+	*addr = (FPW) 0x00D000D0;
+}
+
+
+/*-----------------------------------------------------------------------
+ */
+
+int flash_erase (flash_info_t * info, int s_first, int s_last)
+{
+	int flag, prot, sect;
+	ulong type, start, last;
+	int rcode = 0;
+
+	if ((s_first < 0) || (s_first > s_last)) {
+		if (info->flash_id == FLASH_UNKNOWN) {
+			printf ("- missing\n");
+		} else {
+			printf ("- no sectors to erase\n");
+		}
+		return 1;
+	}
+
+	type = (info->flash_id & FLASH_VENDMASK);
+	if ((type != FLASH_MAN_INTEL)) {
+		printf ("Can't erase unknown flash type %08lx - aborted\n",
+				info->flash_id);
+		return 1;
+	}
+
+	prot = 0;
+	for (sect = s_first; sect <= s_last; ++sect) {
+		if (info->protect[sect]) {
+			prot++;
+		}
+	}
+
+	if (prot) {
+		printf ("- Warning: %d protected sectors will not be erased!\n",
+				prot);
+	} else {
+		printf ("\n");
+	}
+
+
+	start = get_timer (0);
+	last = start;
+
+	/* Disable interrupts which might cause a timeout here */
+	flag = disable_interrupts ();
+
+	/* Start erase on unprotected sectors */
+	for (sect = s_first; sect <= s_last; sect++) {
+		if (info->protect[sect] == 0) {	/* not protected */
+			FPWV *addr = (FPWV *) (info->start[sect]);
+			FPW status;
+
+			printf ("Erasing sector %2d ... ", sect);
+
+			flash_unprotect_sectors (addr);
+
+			/* arm simple, non interrupt dependent timer */
+			reset_timer_masked ();
+
+			*addr = (FPW) 0x00500050;/* clear status register */
+			*addr = (FPW) 0x00200020;/* erase setup */
+			*addr = (FPW) 0x00D000D0;/* erase confirm */
+
+			while (((status =
+				*addr) & (FPW) 0x00800080) !=
+				(FPW) 0x00800080) {
+					if (get_timer_masked () >
+					CFG_FLASH_ERASE_TOUT) {
+					printf ("Timeout\n");
+					/* suspend erase     */
+					*addr = (FPW) 0x00B000B0;
+					/* reset to read mode */
+					*addr = (FPW) 0x00FF00FF;
+					rcode = 1;
+					break;
+				}
+			}
+
+			/* clear status register cmd.   */
+			*addr = (FPW) 0x00500050;
+			*addr = (FPW) 0x00FF00FF;/* resest to read mode */
+			printf (" done\n");
+		}
+	}
+	return rcode;
+}
+
+/*-----------------------------------------------------------------------
+ * Copy memory to flash, returns:
+ * 0 - OK
+ * 1 - write timeout
+ * 2 - Flash not erased
+ * 4 - Flash not identified
+ */
+
+int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt)
+{
+	ulong cp, wp;
+	FPW data;
+	int count, i, l, rc, port_width;
+
+	if (info->flash_id == FLASH_UNKNOWN) {
+		return 4;
+	}
+/* get lower word aligned address */
+#ifdef FLASH_PORT_WIDTH16
+	wp = (addr & ~1);
+	port_width = 2;
+#else
+	wp = (addr & ~3);
+	port_width = 4;
+#endif
+
+	/*
+	 * handle unaligned start bytes
+	 */
+	if ((l = addr - wp) != 0) {
+		data = 0;
+		for (i = 0, cp = wp; i < l; ++i, ++cp) {
+			data = (data << 8) | (*(uchar *) cp);
+		}
+		for (; i < port_width && cnt > 0; ++i) {
+			data = (data << 8) | *src++;
+			--cnt;
+			++cp;
+		}
+		for (; cnt == 0 && i < port_width; ++i, ++cp) {
+			data = (data << 8) | (*(uchar *) cp);
+		}
+
+		if ((rc = write_data (info, wp, SWAP (data))) != 0) {
+			return (rc);
+		}
+		wp += port_width;
+	}
+
+	/*
+	 * handle word aligned part
+	 */
+	count = 0;
+	while (cnt >= port_width) {
+		data = 0;
+		for (i = 0; i < port_width; ++i) {
+			data = (data << 8) | *src++;
+		}
+		if ((rc = write_data (info, wp, SWAP (data))) != 0) {
+			return (rc);
+		}
+		wp += port_width;
+		cnt -= port_width;
+		if (count++ > 0x800) {
+			spin_wheel ();
+			count = 0;
+		}
+	}
+
+	if (cnt == 0) {
+		return (0);
+	}
+
+	/*
+	 * handle unaligned tail bytes
+	 */
+	data = 0;
+	for (i = 0, cp = wp; i < port_width && cnt > 0; ++i, ++cp) {
+		data = (data << 8) | *src++;
+		--cnt;
+	}
+	for (; i < port_width; ++i, ++cp) {
+		data = (data << 8) | (*(uchar *) cp);
+	}
+
+	return (write_data (info, wp, SWAP (data)));
+}
+
+/*-----------------------------------------------------------------------
+ * Write a word or halfword to Flash, returns:
+ * 0 - OK
+ * 1 - write timeout
+ * 2 - Flash not erased
+ */
+static int write_data (flash_info_t * info, ulong dest, FPW data)
+{
+	FPWV *addr = (FPWV *) dest;
+	ulong status;
+	int flag;
+
+	/* Check if Flash is (sufficiently) erased */
+	if ((*addr & data) != data) {
+		printf ("not erased at %08lx (%x)\n", (ulong) addr, *addr);
+		return (2);
+	}
+	flash_unprotect_sectors (addr);
+	/* Disable interrupts which might cause a timeout here */
+	flag = disable_interrupts ();
+	*addr = (FPW) 0x00400040;	/* write setup */
+	*addr = data;
+
+	/* arm simple, non interrupt dependent timer */
+	reset_timer_masked ();
+
+	/* wait while polling the status register */
+	while (((status = *addr) & (FPW) 0x00800080) != (FPW) 0x00800080) {
+		if (get_timer_masked () > CFG_FLASH_WRITE_TOUT) {
+			*addr = (FPW) 0x00FF00FF;	/* restore read mode */
+			return (1);
+		}
+	}
+	*addr = (FPW) 0x00FF00FF;	/* restore read mode */
+	return (0);
+}
+
+void inline spin_wheel (void)
+{
+	static int p = 0;
+	static char w[] = "\\/-";
+
+	printf ("\010%c", w[p]);
+	(++p == 3) ? (p = 0) : 0;
+}
--- a/board/integratorap/integratorap.c
+++ b/board/integratorap/integratorap.c
@@ -0,0 +1,477 @@
+/*
+ * (C) Copyright 2002
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Marius Groeger <mgroeger@sysgo.de>
+ *
+ * (C) Copyright 2002
+ * David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
+ *
+ * (C) Copyright 2003
+ * Texas Instruments, <www.ti.com>
+ * Kshitij Gupta <Kshitij@ti.com>
+ *
+ * (C) Copyright 2004
+ * ARM Ltd.
+ * Philippe Robin, <philippe.robin@arm.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+
+#ifdef CONFIG_PCI
+#   include <pci.h>
+#endif
+
+void flash__init (void);
+void ether__init (void);
+void peripheral_power_enable (void);
+
+#if defined(CONFIG_SHOW_BOOT_PROGRESS)
+void show_boot_progress(int progress)
+{
+    printf("Boot reached stage %d\n", progress);
+}
+#endif
+
+#define COMP_MODE_ENABLE ((unsigned int)0x0000EAEF)
+
+static inline void delay (unsigned long loops)
+{
+	__asm__ volatile ("1:\n"
+		"subs %0, %1, #1\n"
+		"bne 1b":"=r" (loops):"0" (loops));
+}
+
+/*
+ * Miscellaneous platform dependent initialisations
+ */
+
+int board_init (void)
+{
+	DECLARE_GLOBAL_DATA_PTR;
+
+	/* arch number of Integrator Board */
+	gd->bd->bi_arch_number = 21;
+
+	/* adress of boot parameters */
+	gd->bd->bi_boot_params = 0x00000100;
+
+	icache_enable ();
+
+	flash__init ();
+	return 0;
+}
+
+
+int misc_init_r (void)
+{
+#ifdef CONFIG_PCI
+	pci_init();
+#endif
+	setenv("verify", "n");
+	return (0);
+}
+
+/*
+ * Initialize PCI Devices, report devices found.
+ */
+#ifdef CONFIG_PCI
+
+#ifndef CONFIG_PCI_PNP
+
+static struct pci_config_table pci_integrator_config_table[] = {
+	{ PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, 0x0f, PCI_ANY_ID,
+	  pci_cfgfunc_config_device, { PCI_ENET0_IOADDR,
+				       PCI_ENET0_MEMADDR,
+				       PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER }},
+	{ }
+};
+#endif
+
+/* V3 access routines */
+#define _V3Write16(o,v) (*(volatile unsigned short *)(PCI_V3_BASE + (unsigned int)(o)) = (unsigned short)(v))
+#define _V3Read16(o)    (*(volatile unsigned short *)(PCI_V3_BASE + (unsigned int)(o)))
+
+#define _V3Write32(o,v) (*(volatile unsigned int *)(PCI_V3_BASE + (unsigned int)(o)) = (unsigned int)(v))
+#define _V3Read32(o)    (*(volatile unsigned int *)(PCI_V3_BASE + (unsigned int)(o)))
+
+/* Compute address necessary to access PCI config space for the given */
+/* bus and device. */
+#define PCI_CONFIG_ADDRESS( __bus, __devfn, __offset ) ({				\
+	unsigned int __address, __devicebit;						\
+	unsigned short __mapaddress;							\
+	unsigned int __dev = PCI_DEV (__devfn);	/* FIXME to check!! (slot?) */		\
+											\
+	if (__bus == 0) {								\
+		/* local bus segment so need a type 0 config cycle */			\
+		/* build the PCI configuration "address" with one-hot in A31-A11 */	\
+		__address = PCI_CONFIG_BASE;						\
+		__address |= ((__devfn & 0x07) << 8);					\
+		__address |= __offset & 0xFF;						\
+		__mapaddress = 0x000A;	/* 101=>config cycle, 0=>A1=A0=0 */		\
+		__devicebit = (1 << (__dev + 11));					\
+											\
+		if ((__devicebit & 0xFF000000) != 0) {					\
+			/* high order bits are handled by the MAP register */		\
+			__mapaddress |= (__devicebit >> 16);				\
+		} else {								\
+			/* low order bits handled directly in the address */		\
+			__address |= __devicebit;					\
+		}									\
+	} else {		/* bus !=0 */						\
+		/* not the local bus segment so need a type 1 config cycle */		\
+		/* A31-A24 are don't care (so clear to 0) */				\
+		__mapaddress = 0x000B;	/* 101=>config cycle, 1=>A1&A0 from PCI_CFG */	\
+		__address = PCI_CONFIG_BASE;						\
+		__address |= ((__bus & 0xFF) << 16);	/* bits 23..16 = bus number     */  \
+		__address |= ((__dev & 0x1F) << 11);	/* bits 15..11 = device number  */  \
+		__address |= ((__devfn & 0x07) << 8);	/* bits 10..8  = function number */ \
+		__address |= __offset & 0xFF;	/* bits  7..0  = register number */	\
+	}										\
+	_V3Write16 (V3_LB_MAP1, __mapaddress);						\
+	__address;									\
+})
+
+/* _V3OpenConfigWindow - open V3 configuration window */
+#define _V3OpenConfigWindow() {								\
+	/* Set up base0 to see all 512Mbytes of memory space (not	     */		\
+	/* prefetchable), this frees up base1 for re-use by configuration*/		\
+	/* memory */									\
+											\
+	_V3Write32 (V3_LB_BASE0, ((INTEGRATOR_PCI_BASE & 0xFFF00000) |			\
+				     0x90 | V3_LB_BASE_M_ENABLE));			\
+	/* Set up base1 to point into configuration space, note that MAP1 */		\
+	/* register is set up by pciMakeConfigAddress(). */				\
+											\
+	_V3Write32 (V3_LB_BASE1, ((CPU_PCI_CNFG_ADRS & 0xFFF00000) |			\
+				     0x40 | V3_LB_BASE_M_ENABLE));			\
+}
+
+/* _V3CloseConfigWindow - close V3 configuration window */
+#define _V3CloseConfigWindow() {							\
+    /* Reassign base1 for use by prefetchable PCI memory */				\
+	_V3Write32 (V3_LB_BASE1, (((INTEGRATOR_PCI_BASE + 0x10000000) & 0xFFF00000)	\
+					| 0x84 | V3_LB_BASE_M_ENABLE));			\
+	_V3Write16 (V3_LB_MAP1,								\
+	    (((INTEGRATOR_PCI_BASE + 0x10000000) & 0xFFF00000) >> 16) | 0x0006);	\
+											\
+	/* And shrink base0 back to a 256M window (NOTE: MAP0 already correct) */	\
+											\
+	_V3Write32 (V3_LB_BASE0, ((INTEGRATOR_PCI_BASE & 0xFFF00000) |			\
+			     0x80 | V3_LB_BASE_M_ENABLE));				\
+}
+
+static int pci_integrator_read_byte (struct pci_controller *hose, pci_dev_t dev,
+				     int offset, unsigned char *val)
+{
+	_V3OpenConfigWindow ();
+	*val = *(volatile unsigned char *) PCI_CONFIG_ADDRESS (PCI_BUS (dev),
+							       PCI_FUNC (dev),
+							       offset);
+	_V3CloseConfigWindow ();
+
+	return 0;
+}
+
+static int pci_integrator_read__word (struct pci_controller *hose,
+				      pci_dev_t dev, int offset,
+				      unsigned short *val)
+{
+	_V3OpenConfigWindow ();
+	*val = *(volatile unsigned short *) PCI_CONFIG_ADDRESS (PCI_BUS (dev),
+								PCI_FUNC (dev),
+								offset);
+	_V3CloseConfigWindow ();
+
+	return 0;
+}
+
+static int pci_integrator_read_dword (struct pci_controller *hose,
+				      pci_dev_t dev, int offset,
+				      unsigned int *val)
+{
+	_V3OpenConfigWindow ();
+	*val = *(volatile unsigned short *) PCI_CONFIG_ADDRESS (PCI_BUS (dev),
+								PCI_FUNC (dev),
+								offset);
+	*val |= (*(volatile unsigned int *)
+		 PCI_CONFIG_ADDRESS (PCI_BUS (dev), PCI_FUNC (dev),
+				     (offset + 2))) << 16;
+	_V3CloseConfigWindow ();
+
+	return 0;
+}
+
+static int pci_integrator_write_byte (struct pci_controller *hose,
+				      pci_dev_t dev, int offset,
+				      unsigned char val)
+{
+	_V3OpenConfigWindow ();
+	*(volatile unsigned char *) PCI_CONFIG_ADDRESS (PCI_BUS (dev),
+							PCI_FUNC (dev),
+							offset) = val;
+	_V3CloseConfigWindow ();
+
+	return 0;
+}
+
+static int pci_integrator_write_word (struct pci_controller *hose,
+				      pci_dev_t dev, int offset,
+				      unsigned short val)
+{
+	_V3OpenConfigWindow ();
+	*(volatile unsigned short *) PCI_CONFIG_ADDRESS (PCI_BUS (dev),
+							 PCI_FUNC (dev),
+							 offset) = val;
+	_V3CloseConfigWindow ();
+
+	return 0;
+}
+
+static int pci_integrator_write_dword (struct pci_controller *hose,
+				       pci_dev_t dev, int offset,
+				       unsigned int val)
+{
+	_V3OpenConfigWindow ();
+	*(volatile unsigned short *) PCI_CONFIG_ADDRESS (PCI_BUS (dev),
+							 PCI_FUNC (dev),
+							 offset) = (val & 0xFFFF);
+	*(volatile unsigned short *) PCI_CONFIG_ADDRESS (PCI_BUS (dev),
+							 PCI_FUNC (dev),
+							 (offset + 2)) = ((val >> 16) & 0xFFFF);
+	_V3CloseConfigWindow ();
+
+	return 0;
+}
+/******************************
+ * PCI initialisation
+ ******************************/
+
+struct pci_controller integrator_hose = {
+#ifndef CONFIG_PCI_PNP
+	config_table: pci_integrator_config_table,
+#endif
+};
+
+void pci_init_board (void)
+{
+	volatile int i, j;
+	struct pci_controller *hose = &integrator_hose;
+
+	/* setting this register will take the V3 out of reset */
+
+	*(volatile unsigned int *) (INTEGRATOR_SC_PCIENABLE) = 1;
+
+	/* wait a few usecs to settle the device and the PCI bus */
+
+	for (i = 0; i < 100; i++)
+		j = i + 1;
+
+	/* Now write the Base I/O Address Word to V3_BASE + 0x6C */
+
+	*(volatile unsigned short *) (V3_BASE + V3_LB_IO_BASE) =
+		(unsigned short) (V3_BASE >> 16);
+
+	do {
+		*(volatile unsigned char *) (V3_BASE + V3_MAIL_DATA) = 0xAA;
+		*(volatile unsigned char *) (V3_BASE + V3_MAIL_DATA + 4) =
+			0x55;
+	} while (*(volatile unsigned char *) (V3_BASE + V3_MAIL_DATA) != 0xAA
+		 || *(volatile unsigned char *) (V3_BASE + V3_MAIL_DATA +
+						 4) != 0x55);
+
+	/* Make sure that V3 register access is not locked, if it is, unlock it */
+
+	if ((*(volatile unsigned short *) (V3_BASE + V3_SYSTEM) &
+	     V3_SYSTEM_M_LOCK)
+	    == V3_SYSTEM_M_LOCK)
+		*(volatile unsigned short *) (V3_BASE + V3_SYSTEM) = 0xA05F;
+
+	/* Ensure that the slave accesses from PCI are disabled while we */
+	/* setup windows */
+
+	*(volatile unsigned short *) (V3_BASE + V3_PCI_CMD) &=
+		~(V3_COMMAND_M_MEM_EN | V3_COMMAND_M_IO_EN);
+
+	/* Clear RST_OUT to 0; keep the PCI bus in reset until we've finished */
+
+	*(volatile unsigned short *) (V3_BASE + V3_SYSTEM) &=
+		~V3_SYSTEM_M_RST_OUT;
+
+	/* Make all accesses from PCI space retry until we're ready for them */
+
+	*(volatile unsigned short *) (V3_BASE + V3_PCI_CFG) |=
+		V3_PCI_CFG_M_RETRY_EN;
+
+	/* Set up any V3 PCI Configuration Registers that we absolutely have to */
+	/* LB_CFG controls Local Bus protocol. */
+	/* Enable LocalBus byte strobes for READ accesses too. */
+	/* set bit 7 BE_IMODE and bit 6 BE_OMODE */
+
+	*(volatile unsigned short *) (V3_BASE + V3_LB_CFG) |= 0x0C0;
+
+	/* PCI_CMD controls overall PCI operation. */
+	/* Enable PCI bus master. */
+
+	*(volatile unsigned short *) (V3_BASE + V3_PCI_CMD) |= 0x04;
+
+	/* PCI_MAP0 controls where the PCI to CPU memory window is on Local Bus */
+
+	*(volatile unsigned int *) (V3_BASE + V3_PCI_MAP0) =
+		(INTEGRATOR_BOOT_ROM_BASE) | (V3_PCI_MAP_M_ADR_SIZE_512M |
+					      V3_PCI_MAP_M_REG_EN |
+					      V3_PCI_MAP_M_ENABLE);
+
+	/* PCI_BASE0 is the PCI address of the start of the window */
+
+	*(volatile unsigned int *) (V3_BASE + V3_PCI_BASE0) =
+		INTEGRATOR_BOOT_ROM_BASE;
+
+	/* PCI_MAP1 is LOCAL address of the start of the window */
+
+	*(volatile unsigned int *) (V3_BASE + V3_PCI_MAP1) =
+		(INTEGRATOR_HDR0_SDRAM_BASE) | (V3_PCI_MAP_M_ADR_SIZE_1024M |
+						V3_PCI_MAP_M_REG_EN |
+						V3_PCI_MAP_M_ENABLE);
+
+	/* PCI_BASE1 is the PCI address of the start of the window */
+
+	*(volatile unsigned int *) (V3_BASE + V3_PCI_BASE1) =
+		INTEGRATOR_HDR0_SDRAM_BASE;
+
+	/* Set up the windows from local bus memory into PCI configuration, */
+	/* I/O and Memory. */
+	/* PCI I/O, LB_BASE2 and LB_MAP2 are used exclusively for this. */
+
+	*(volatile unsigned short *) (V3_BASE + V3_LB_BASE2) =
+		((CPU_PCI_IO_ADRS >> 24) << 8) | V3_LB_BASE_M_ENABLE;
+	*(volatile unsigned short *) (V3_BASE + V3_LB_MAP2) = 0;
+
+	/* PCI Configuration, use LB_BASE1/LB_MAP1. */
+
+	/* PCI Memory use LB_BASE0/LB_MAP0 and LB_BASE1/LB_MAP1 */
+	/* Map first 256Mbytes as non-prefetchable via BASE0/MAP0 */
+	/* (INTEGRATOR_PCI_BASE == PCI_MEM_BASE) */
+
+	*(volatile unsigned int *) (V3_BASE + V3_LB_BASE0) =
+		INTEGRATOR_PCI_BASE | (0x80 | V3_LB_BASE_M_ENABLE);
+
+	*(volatile unsigned short *) (V3_BASE + V3_LB_MAP0) =
+		((INTEGRATOR_PCI_BASE >> 20) << 0x4) | 0x0006;
+
+	/* Map second 256 Mbytes as prefetchable via BASE1/MAP1 */
+
+	*(volatile unsigned int *) (V3_BASE + V3_LB_BASE1) =
+		INTEGRATOR_PCI_BASE | (0x84 | V3_LB_BASE_M_ENABLE);
+
+	*(volatile unsigned short *) (V3_BASE + V3_LB_MAP1) =
+		(((INTEGRATOR_PCI_BASE + 0x10000000) >> 20) << 4) | 0x0006;
+
+	/* Allow accesses to PCI Configuration space */
+	/* and set up A1, A0 for type 1 config cycles */
+
+	*(volatile unsigned short *) (V3_BASE + V3_PCI_CFG) =
+		((*(volatile unsigned short *) (V3_BASE + V3_PCI_CFG)) &
+		 ~(V3_PCI_CFG_M_RETRY_EN | V3_PCI_CFG_M_AD_LOW1)) |
+		V3_PCI_CFG_M_AD_LOW0;
+
+	/* now we can allow in PCI MEMORY accesses */
+
+	*(volatile unsigned short *) (V3_BASE + V3_PCI_CMD) =
+		(*(volatile unsigned short *) (V3_BASE + V3_PCI_CMD)) |
+		V3_COMMAND_M_MEM_EN;
+
+	/* Set RST_OUT to take the PCI bus is out of reset, PCI devices can */
+	/* initialise and lock the V3 system register so that no one else */
+	/* can play with it */
+
+	*(volatile unsigned short *) (V3_BASE + V3_SYSTEM) =
+		(*(volatile unsigned short *) (V3_BASE + V3_SYSTEM)) |
+		V3_SYSTEM_M_RST_OUT;
+
+	*(volatile unsigned short *) (V3_BASE + V3_SYSTEM) =
+		(*(volatile unsigned short *) (V3_BASE + V3_SYSTEM)) |
+		V3_SYSTEM_M_LOCK;
+
+	/*
+	 * Register the hose
+	 */
+	hose->first_busno = 0;
+	hose->last_busno = 0xff;
+
+	/* System memory space */
+	pci_set_region (hose->regions + 0,
+			0x00000000, 0x40000000, 0x01000000,
+			PCI_REGION_MEM | PCI_REGION_MEMORY);
+
+	/* PCI Memory - config space */
+	pci_set_region (hose->regions + 1,
+			0x00000000, 0x62000000, 0x01000000, PCI_REGION_MEM);
+
+	/* PCI V3 regs */
+	pci_set_region (hose->regions + 2,
+			0x00000000, 0x61000000, 0x00080000, PCI_REGION_MEM);
+
+	/* PCI I/O space */
+	pci_set_region (hose->regions + 3,
+			0x00000000, 0x60000000, 0x00010000, PCI_REGION_IO);
+
+	pci_set_ops (hose,
+		     pci_integrator_read_byte,
+		     pci_integrator_read__word,
+		     pci_integrator_read_dword,
+		     pci_integrator_write_byte,
+		     pci_integrator_write_word, pci_integrator_write_dword);
+
+	hose->region_count = 4;
+
+	pci_register_hose (hose);
+
+	pciauto_config_init (hose);
+	pciauto_config_device (hose, 0);
+
+	hose->last_busno = pci_hose_scan (hose);
+}
+#endif
+
+/******************************
+ Routine:
+ Description:
+******************************/
+void flash__init (void)
+{
+}
+/*************************************************************
+ Routine:ether__init
+ Description: take the Ethernet controller out of reset and wait
+	  		   for the EEPROM load to complete.
+*************************************************************/
+void ether__init (void)
+{
+}
+
+/******************************
+ Routine:
+ Description:
+******************************/
+int dram_init (void)
+{
+	return 0;
+}
--- a/board/integratorap/platform.S
+++ b/board/integratorap/platform.S
@@ -0,0 +1,33 @@
+/*
+ * Board specific setup info
+ *
+ * (C) Copyright 2004, ARM Ltd.
+ * Philippe Robin, <philippe.robin@arm.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <version.h>
+
+.globl platformsetup
+platformsetup:
+
+	/* All done by Integrator's boot monitor! */
+	mov pc, lr
--- a/board/integratorap/u-boot.lds
+++ b/board/integratorap/u-boot.lds
@@ -0,0 +1,50 @@
+/*
+ * (C) Copyright 2002
+ * Gary Jennejohn, DENX Software Engineering, <gj@denx.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+	. = 0x00000000;
+	. = ALIGN(4);
+	.text	:
+	{
+	  cpu/arm926ejs/start.o	(.text)
+	  *(.text)
+	}
+	.rodata : { *(.rodata) }
+	. = ALIGN(4);
+	.data : { *(.data) }
+	. = ALIGN(4);
+	.got : { *(.got) }
+
+	__u_boot_cmd_start = .;
+	.u_boot_cmd : { *(.u_boot_cmd) }
+	__u_boot_cmd_end = .;
+
+	. = ALIGN(4);
+	__bss_start = .;
+	.bss : { *(.bss) }
+	_end = .;
+}
--- a/board/integratorcp/Makefile
+++ b/board/integratorcp/Makefile
@@ -0,0 +1,47 @@
+#
+# (C) Copyright 2000-2004
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	:= integratorcp.o flash.o
+SOBJS	:= platform.o
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) crv $@ $^
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+-include .depend
+
+#########################################################################
--- a/board/integratorcp/config.mk
+++ b/board/integratorcp/config.mk
@@ -0,0 +1,5 @@
+#
+# image should be loaded at 0x01000000
+#
+
+TEXT_BASE = 0x01000000
--- a/board/integratorcp/flash.c
+++ b/board/integratorcp/flash.c
@@ -0,0 +1,473 @@
+/*
+ * (C) Copyright 2001
+ * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net
+ *
+ * (C) Copyright 2001-2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * (C) Copyright 2003
+ * Texas Instruments, <www.ti.com>
+ * Kshitij Gupta <Kshitij@ti.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <linux/byteorder/swab.h>
+
+#define PHYS_FLASH_SECT_SIZE	0x00020000	/* 256 KB sectors (x2) */
+flash_info_t flash_info[CFG_MAX_FLASH_BANKS];	/* info for FLASH chips    */
+
+/* Board support for 1 or 2 flash devices */
+#undef FLASH_PORT_WIDTH32
+#define FLASH_PORT_WIDTH16
+
+#ifdef FLASH_PORT_WIDTH16
+#define FLASH_PORT_WIDTH		ushort
+#define FLASH_PORT_WIDTHV		vu_short
+#define SWAP(x)			__swab16(x)
+#else
+#define FLASH_PORT_WIDTH		ulong
+#define FLASH_PORT_WIDTHV		vu_long
+#define SWAP(x)			__swab32(x)
+#endif
+
+#define FPW	FLASH_PORT_WIDTH
+#define FPWV	FLASH_PORT_WIDTHV
+
+#define mb() __asm__ __volatile__ ("" : : : "memory")
+
+
+/* Flash Organization Structure */
+typedef struct OrgDef {
+	unsigned int sector_number;
+	unsigned int sector_size;
+} OrgDef;
+
+
+/* Flash Organizations */
+OrgDef OrgIntel_28F256L18T[] = {
+	{4, 32 * 1024},				/* 4 * 32kBytes sectors */
+	{255, 128 * 1024},			/* 255 * 128kBytes sectors */
+};
+
+
+/*-----------------------------------------------------------------------
+ * Functions
+ */
+unsigned long flash_init (void);
+static ulong flash_get_size (FPW * addr, flash_info_t * info);
+static int write_data (flash_info_t * info, ulong dest, FPW data);
+static void flash_get_offsets (ulong base, flash_info_t * info);
+void inline spin_wheel (void);
+void flash_print_info (flash_info_t * info);
+void flash_unprotect_sectors (FPWV * addr);
+int flash_erase (flash_info_t * info, int s_first, int s_last);
+int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt);
+
+/*-----------------------------------------------------------------------
+ */
+
+unsigned long flash_init (void)
+{
+	int i;
+	ulong size = 0;
+	for (i = 0; i < CFG_MAX_FLASH_BANKS; i++) {
+		switch (i) {
+		case 0:
+			flash_get_size ((FPW *) PHYS_FLASH_1, &flash_info[i]);
+			flash_get_offsets (PHYS_FLASH_1, &flash_info[i]);
+			break;
+		default:
+			panic ("configured too many flash banks!\n");
+			break;
+		}
+		size += flash_info[i].size;
+	}
+
+	/* Protect monitor and environment sectors
+	 */
+	flash_protect (FLAG_PROTECT_SET,
+			CFG_FLASH_BASE,
+			CFG_FLASH_BASE + monitor_flash_len - 1, &flash_info[0]);
+
+	return size;
+}
+
+/*-----------------------------------------------------------------------
+ */
+static void flash_get_offsets (ulong base, flash_info_t * info)
+{
+	int i;
+	OrgDef *pOrgDef;
+
+	pOrgDef = OrgIntel_28F256L18T;
+	if (info->flash_id == FLASH_UNKNOWN) {
+		return;
+	}
+
+	if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL) {
+		for (i = 0; i < info->sector_count; i++) {
+			if (i > 255) {
+				info->start[i] = base + (i * 0x8000);
+				info->protect[i] = 0;
+			} else {
+				info->start[i] = base +
+						(i * PHYS_FLASH_SECT_SIZE);
+				info->protect[i] = 0;
+			}
+		}
+	}
+}
+
+/*-----------------------------------------------------------------------
+ */
+void flash_print_info (flash_info_t * info)
+{
+	int i;
+
+	if (info->flash_id == FLASH_UNKNOWN) {
+		printf ("missing or unknown FLASH type\n");
+		return;
+	}
+
+	switch (info->flash_id & FLASH_VENDMASK) {
+	case FLASH_MAN_INTEL:
+		printf ("INTEL ");
+		break;
+	default:
+		printf ("Unknown Vendor ");
+		break;
+	}
+
+	switch (info->flash_id & FLASH_TYPEMASK) {
+	case FLASH_28F256L18T:
+		printf ("FLASH 28F256L18T\n");
+		break;
+	default:
+		printf ("Unknown Chip Type\n");
+		break;
+	}
+
+	printf ("  Size: %ld MB in %d Sectors\n",
+			info->size >> 20, info->sector_count);
+
+	printf ("  Sector Start Addresses:");
+	for (i = 0; i < info->sector_count; ++i) {
+		if ((i % 5) == 0)
+			printf ("\n   ");
+		printf (" %08lX%s",
+			info->start[i], info->protect[i] ? " (RO)" : "     ");
+	}
+	printf ("\n");
+	return;
+}
+
+/*
+ * The following code cannot be run from FLASH!
+ */
+static ulong flash_get_size (FPW * addr, flash_info_t * info)
+{
+	volatile FPW value;
+
+	/* Write auto select command: read Manufacturer ID */
+	addr[0x5555] = (FPW) 0x00AA00AA;
+	addr[0x2AAA] = (FPW) 0x00550055;
+	addr[0x5555] = (FPW) 0x00900090;
+
+	mb ();
+	value = addr[0];
+
+	switch (value) {
+
+	case (FPW) INTEL_MANUFACT:
+		info->flash_id = FLASH_MAN_INTEL;
+		break;
+
+	default:
+		info->flash_id = FLASH_UNKNOWN;
+		info->sector_count = 0;
+		info->size = 0;
+		addr[0] = (FPW) 0x00FF00FF;	/* restore read mode */
+		return (0);		/* no or unknown flash  */
+	}
+
+	mb ();
+	value = addr[1];	/* device ID        */
+	switch (value) {
+
+	case (FPW) (INTEL_ID_28F256L18T):
+		info->flash_id += FLASH_28F256L18T;
+		info->sector_count = 259;
+		info->size = 0x02000000;
+		break;			/* => 32 MB     */
+
+	default:
+		info->flash_id = FLASH_UNKNOWN;
+		break;
+	}
+
+	if (info->sector_count > CFG_MAX_FLASH_SECT) {
+		printf ("** ERROR: sector count %d > max (%d) **\n",
+				info->sector_count, CFG_MAX_FLASH_SECT);
+		info->sector_count = CFG_MAX_FLASH_SECT;
+	}
+
+	addr[0] = (FPW) 0x00FF00FF;	/* restore read mode */
+
+	return (info->size);
+}
+
+
+/* unprotects a sector for write and erase
+ * on some intel parts, this unprotects the entire chip, but it
+ * wont hurt to call this additional times per sector...
+ */
+void flash_unprotect_sectors (FPWV * addr)
+{
+#define PD_FINTEL_WSMS_READY_MASK    0x0080
+
+	*addr = (FPW) 0x00500050;	/* clear status register */
+
+	/* this sends the clear lock bit command */
+	*addr = (FPW) 0x00600060;
+	*addr = (FPW) 0x00D000D0;
+}
+
+
+/*-----------------------------------------------------------------------
+ */
+
+int flash_erase (flash_info_t * info, int s_first, int s_last)
+{
+	int flag, prot, sect;
+	ulong type, start, last;
+	int rcode = 0;
+
+	if ((s_first < 0) || (s_first > s_last)) {
+		if (info->flash_id == FLASH_UNKNOWN) {
+			printf ("- missing\n");
+		} else {
+			printf ("- no sectors to erase\n");
+		}
+		return 1;
+	}
+
+	type = (info->flash_id & FLASH_VENDMASK);
+	if ((type != FLASH_MAN_INTEL)) {
+		printf ("Can't erase unknown flash type %08lx - aborted\n",
+				info->flash_id);
+		return 1;
+	}
+
+	prot = 0;
+	for (sect = s_first; sect <= s_last; ++sect) {
+		if (info->protect[sect]) {
+			prot++;
+		}
+	}
+
+	if (prot) {
+		printf ("- Warning: %d protected sectors will not be erased!\n",
+				prot);
+	} else {
+		printf ("\n");
+	}
+
+
+	start = get_timer (0);
+	last = start;
+
+	/* Disable interrupts which might cause a timeout here */
+	flag = disable_interrupts ();
+
+	/* Start erase on unprotected sectors */
+	for (sect = s_first; sect <= s_last; sect++) {
+		if (info->protect[sect] == 0) {	/* not protected */
+			FPWV *addr = (FPWV *) (info->start[sect]);
+			FPW status;
+
+			printf ("Erasing sector %2d ... ", sect);
+
+			flash_unprotect_sectors (addr);
+
+			/* arm simple, non interrupt dependent timer */
+			reset_timer_masked ();
+
+			*addr = (FPW) 0x00500050;/* clear status register */
+			*addr = (FPW) 0x00200020;/* erase setup */
+			*addr = (FPW) 0x00D000D0;/* erase confirm */
+
+			while (((status =
+				*addr) & (FPW) 0x00800080) !=
+				(FPW) 0x00800080) {
+					if (get_timer_masked () >
+					CFG_FLASH_ERASE_TOUT) {
+					printf ("Timeout\n");
+					/* suspend erase     */
+					*addr = (FPW) 0x00B000B0;
+					/* reset to read mode */
+					*addr = (FPW) 0x00FF00FF;
+					rcode = 1;
+					break;
+				}
+			}
+
+			/* clear status register cmd.   */
+			*addr = (FPW) 0x00500050;
+			*addr = (FPW) 0x00FF00FF;/* resest to read mode */
+			printf (" done\n");
+		}
+	}
+	return rcode;
+}
+
+/*-----------------------------------------------------------------------
+ * Copy memory to flash, returns:
+ * 0 - OK
+ * 1 - write timeout
+ * 2 - Flash not erased
+ * 4 - Flash not identified
+ */
+
+int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt)
+{
+	ulong cp, wp;
+	FPW data;
+	int count, i, l, rc, port_width;
+
+	if (info->flash_id == FLASH_UNKNOWN) {
+		return 4;
+	}
+/* get lower word aligned address */
+#ifdef FLASH_PORT_WIDTH16
+	wp = (addr & ~1);
+	port_width = 2;
+#else
+	wp = (addr & ~3);
+	port_width = 4;
+#endif
+
+	/*
+	 * handle unaligned start bytes
+	 */
+	if ((l = addr - wp) != 0) {
+		data = 0;
+		for (i = 0, cp = wp; i < l; ++i, ++cp) {
+			data = (data << 8) | (*(uchar *) cp);
+		}
+		for (; i < port_width && cnt > 0; ++i) {
+			data = (data << 8) | *src++;
+			--cnt;
+			++cp;
+		}
+		for (; cnt == 0 && i < port_width; ++i, ++cp) {
+			data = (data << 8) | (*(uchar *) cp);
+		}
+
+		if ((rc = write_data (info, wp, SWAP (data))) != 0) {
+			return (rc);
+		}
+		wp += port_width;
+	}
+
+	/*
+	 * handle word aligned part
+	 */
+	count = 0;
+	while (cnt >= port_width) {
+		data = 0;
+		for (i = 0; i < port_width; ++i) {
+			data = (data << 8) | *src++;
+		}
+		if ((rc = write_data (info, wp, SWAP (data))) != 0) {
+			return (rc);
+		}
+		wp += port_width;
+		cnt -= port_width;
+		if (count++ > 0x800) {
+			spin_wheel ();
+			count = 0;
+		}
+	}
+
+	if (cnt == 0) {
+		return (0);
+	}
+
+	/*
+	 * handle unaligned tail bytes
+	 */
+	data = 0;
+	for (i = 0, cp = wp; i < port_width && cnt > 0; ++i, ++cp) {
+		data = (data << 8) | *src++;
+		--cnt;
+	}
+	for (; i < port_width; ++i, ++cp) {
+		data = (data << 8) | (*(uchar *) cp);
+	}
+
+	return (write_data (info, wp, SWAP (data)));
+}
+
+/*-----------------------------------------------------------------------
+ * Write a word or halfword to Flash, returns:
+ * 0 - OK
+ * 1 - write timeout
+ * 2 - Flash not erased
+ */
+static int write_data (flash_info_t * info, ulong dest, FPW data)
+{
+	FPWV *addr = (FPWV *) dest;
+	ulong status;
+	int flag;
+
+	/* Check if Flash is (sufficiently) erased */
+	if ((*addr & data) != data) {
+		printf ("not erased at %08lx (%x)\n", (ulong) addr, *addr);
+		return (2);
+	}
+	flash_unprotect_sectors (addr);
+	/* Disable interrupts which might cause a timeout here */
+	flag = disable_interrupts ();
+	*addr = (FPW) 0x00400040;	/* write setup */
+	*addr = data;
+
+	/* arm simple, non interrupt dependent timer */
+	reset_timer_masked ();
+
+	/* wait while polling the status register */
+	while (((status = *addr) & (FPW) 0x00800080) != (FPW) 0x00800080) {
+		if (get_timer_masked () > CFG_FLASH_WRITE_TOUT) {
+			*addr = (FPW) 0x00FF00FF;	/* restore read mode */
+			return (1);
+		}
+	}
+	*addr = (FPW) 0x00FF00FF;	/* restore read mode */
+	return (0);
+}
+
+void inline spin_wheel (void)
+{
+	static int p = 0;
+	static char w[] = "\\/-";
+
+	printf ("\010%c", w[p]);
+	(++p == 3) ? (p = 0) : 0;
+}
--- a/board/integratorcp/integratorcp.c
+++ b/board/integratorcp/integratorcp.c
@@ -0,0 +1,109 @@
+/*
+ * (C) Copyright 2002
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Marius Groeger <mgroeger@sysgo.de>
+ *
+ * (C) Copyright 2002
+ * David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
+ *
+ * (C) Copyright 2003
+ * Texas Instruments, <www.ti.com>
+ * Kshitij Gupta <Kshitij@ti.com>
+ *
+ * (C) Copyright 2004
+ * ARM Ltd.
+ * Philippe Robin, <philippe.robin@arm.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+
+void flash__init (void);
+void ether__init (void);
+void peripheral_power_enable (void);
+
+#if defined(CONFIG_SHOW_BOOT_PROGRESS)
+void show_boot_progress(int progress)
+{
+    printf("Boot reached stage %d\n", progress);
+}
+#endif
+
+#define COMP_MODE_ENABLE ((unsigned int)0x0000EAEF)
+
+static inline void delay (unsigned long loops)
+{
+	__asm__ volatile ("1:\n"
+		"subs %0, %1, #1\n"
+		"bne 1b":"=r" (loops):"0" (loops));
+}
+
+/*
+ * Miscellaneous platform dependent initialisations
+ */
+
+int board_init (void)
+{
+	DECLARE_GLOBAL_DATA_PTR;
+
+	/* arch number of Integrator Board */
+	gd->bd->bi_arch_number = 275;
+
+	/* adress of boot parameters */
+	gd->bd->bi_boot_params = 0x00000100;
+
+	icache_enable ();
+
+	flash__init ();
+	ether__init ();
+	return 0;
+}
+
+
+int misc_init_r (void)
+{
+	setenv("verify", "n");
+	return (0);
+}
+
+/******************************
+ Routine:
+ Description:
+******************************/
+void flash__init (void)
+{
+}
+/*************************************************************
+ Routine:ether__init
+ Description: take the Ethernet controller out of reset and wait
+	  		   for the EEPROM load to complete.
+*************************************************************/
+void ether__init (void)
+{
+}
+
+/******************************
+ Routine:
+ Description:
+******************************/
+int dram_init (void)
+{
+	return 0;
+}
--- a/board/integratorcp/platform.S
+++ b/board/integratorcp/platform.S
@@ -0,0 +1,33 @@
+/*
+ * Board specific setup info
+ *
+ * (C) Copyright 2003, ARM Ltd.
+ * Philippe Robin, <philippe.robin@arm.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <version.h>
+
+.globl platformsetup
+platformsetup:
+
+	/* All done by IntegratorCP's boot monitor! */
+	mov pc, lr
--- a/board/integratorcp/u-boot.lds
+++ b/board/integratorcp/u-boot.lds
@@ -0,0 +1,50 @@
+/*
+ * (C) Copyright 2002
+ * Gary Jennejohn, DENX Software Engineering, <gj@denx.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+	. = 0x00000000;
+	. = ALIGN(4);
+	.text	:
+	{
+	  cpu/arm926ejs/start.o	(.text)
+	  *(.text)
+	}
+	.rodata : { *(.rodata) }
+	. = ALIGN(4);
+	.data : { *(.data) }
+	. = ALIGN(4);
+	.got : { *(.got) }
+
+	__u_boot_cmd_start = .;
+	.u_boot_cmd : { *(.u_boot_cmd) }
+	__u_boot_cmd_end = .;
+
+	. = ALIGN(4);
+	__bss_start = .;
+	.bss : { *(.bss) }
+	_end = .;
+}
--- a/board/modnet50/Makefile
+++ b/board/modnet50/Makefile
@@ -0,0 +1,47 @@
+#
+# (C) Copyright 2000-2004
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	:= modnet50.o flash.o
+SOBJS	:= memsetup.o
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) crv $@ $^
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+-include .depend
+
+#########################################################################
--- a/board/modnet50/config.mk
+++ b/board/modnet50/config.mk
@@ -0,0 +1,29 @@
+#
+# (C) Copyright 2000
+# Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+# Marius Groeger <mgroeger@sysgo.de>
+#
+# (C) Copyright 2000-2004
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+TEXT_BASE = 0x00f00000
+#CROSS_COMPILE = arm-elf-
--- a/board/modnet50/flash.c
+++ b/board/modnet50/flash.c
@@ -0,0 +1,536 @@
+/*
+ * (C) Copyright 2002
+ * MAZeT GmbH <www.mazet.de>
+ * Stephan Linz <linz@mazet.de>, <linz@li-pro.net>
+ *
+ * The most stuff comes from PPCBoot and Linux.
+ *
+ * IMMS gGmbH <www.imms.de>
+ * Thomas Elste <info@elste.org>
+ *
+ * Modifications for ModNET50 Board
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/arch/netarm_registers.h>
+
+#define SCR   (*(volatile unsigned int *)(NETARM_GEN_MODULE_BASE + NETARM_GEN_SYSTEM_CONTROL))
+
+#define ALIGN_ABORT_OFF		SCR = SCR & ~NETARM_GEN_SYS_CFG_ALIGN_ABORT
+#define ALIGN_ABORT_ON		SCR = SCR |  NETARM_GEN_SYS_CFG_ALIGN_ABORT
+
+#define PROG_ADDR		(0x555*2)
+#define SETUP_ADDR		(0x555*2)
+#define ID_ADDR			(0x555*2)
+#define UNLOCK_ADDR1		(0x555*2)
+#define UNLOCK_ADDR2		(0x2AA*2)
+
+#define UNLOCK_CMD1		(0xAA)
+#define UNLOCK_CMD2		(0x55)
+#define ERASE_SUSPEND_CMD	(0xB0)
+#define ERASE_RESUME_CMD	(0x30)
+#define RESET_CMD		(0xF0)
+#define ID_CMD			(0x90)
+#define SECERASE_CMD		(0x30)
+#define CHIPERASE_CMD		(0x10)
+#define PROG_CMD		(0xa0)
+#define SETUP_CMD		(0x80)
+
+#define DQ2			(0x04)
+#define DQ3			(DQ2*2)
+#define DQ5			(DQ3*4)
+#define DQ6			(DQ5*2)
+
+#define WRITE_UNLOCK(addr) { \
+  *(volatile __u16*)(addr + UNLOCK_ADDR1) = (__u16)UNLOCK_CMD1; \
+  *(volatile __u16*)(addr + UNLOCK_ADDR2) = (__u16)UNLOCK_CMD2; \
+}
+
+#define CONFIG_AM29_RESERVED	(0)
+#define K			(1024)
+#define MB			(4)
+
+#define CELL_SIZE		(64*K)
+#define DEVICE_SIZE		(MB*K*K)
+#define CELLS_PER_DEVICE	(DEVICE_SIZE/CELL_SIZE)
+#define RESERVED_CELLS		(CONFIG_AM29_RESERVED*K)/CELL_SIZE
+#define MAX_FLASH_DEVICES	(1)
+#define AVAIL_SIZE		(DEVICE_SIZE*MAX_FLASH_DEVICES - RESERVED_CELLS*CELL_SIZE)
+
+
+flash_info_t flash_info[CFG_MAX_FLASH_BANKS];
+static __u16 toggling_bits;
+
+
+/*-----------------------------------------------------------------------
+ */
+ulong flash_get_size (ulong baseaddr, flash_info_t * info)
+{
+	short i;
+	__u16 flashtest;
+
+	/* Write auto select command sequence and test FLASH answer */
+	WRITE_UNLOCK (baseaddr);
+	*(volatile __u16 *) (baseaddr + ID_ADDR) = (__u16) ID_CMD;
+	flashtest /* manufacturer ID */  = *(volatile __u16 *) (baseaddr);
+	*(volatile __u16 *) (baseaddr + ID_ADDR) = (__u16) RESET_CMD;
+
+	switch ((__u32) ((flashtest << 16) + flashtest)) {
+	case AMD_MANUFACT:
+		info->flash_id = FLASH_MAN_AMD & FLASH_VENDMASK;
+		break;
+	case FUJ_MANUFACT:
+		info->flash_id = FLASH_MAN_FUJ & FLASH_VENDMASK;
+		break;
+	default:
+		info->flash_id = FLASH_UNKNOWN;
+		info->sector_count = 0;
+		info->size = 0;
+		return (0);	/* no or unknown flash */
+	}
+
+	/* Write auto select command sequence and test FLASH answer */
+	WRITE_UNLOCK (baseaddr);
+	*(volatile __u16 *) (baseaddr + ID_ADDR) = (__u16) ID_CMD;
+	flashtest /* device ID */  = *(volatile __u16 *) (baseaddr + 2);
+	*(volatile __u16 *) (baseaddr + ID_ADDR) = (__u16) RESET_CMD;
+
+	/* toggling_bits = (flashtest == TOSHIBA)?(DQ6):(DQ2|DQ6); */
+	toggling_bits = (DQ2 | DQ6);
+
+	switch ((__u32) ((flashtest << 16) + flashtest)) {
+	case AMD_ID_LV160B:
+		info->flash_id +=
+			(FLASH_AM160LV | FLASH_AM160B) & FLASH_TYPEMASK;
+		info->sector_count = CFG_MAX_FLASH_SECT;
+		info->size = CFG_FLASH_SIZE;
+		/* 1*16K Boot Block
+		   2*8K Parameter Block
+		   1*32K Small Main Block */
+		info->start[0] = baseaddr;
+		info->start[1] = baseaddr + 0x4000;
+		info->start[2] = baseaddr + 0x6000;
+		info->start[3] = baseaddr + 0x8000;
+		for (i = 1; i < info->sector_count; i++)
+			info->start[3 + i] = baseaddr + i * CFG_MAIN_SECT_SIZE;
+		break;
+	default:
+		info->flash_id = FLASH_UNKNOWN;
+		return (0);	/* no or unknown flash */
+	}
+
+	for (i = 0; i < info->sector_count; i++) {
+		/* Write auto select command sequence and test FLASH answer */
+		WRITE_UNLOCK (info->start[i]);
+		*(volatile __u16 *) (info->start[i] + ID_ADDR) = (__u16) ID_CMD;
+		flashtest /* protected verify */  = *(volatile __u16 *) (info->start[i] + 4);
+		*(volatile __u16 *) (info->start[i] + ID_ADDR) = (__u16) RESET_CMD;
+		if (flashtest & 0x0001) {
+			info->protect[i] = 1;	/* D0 = 1 if protected */
+		} else {
+			info->protect[i] = 0;
+		}
+	}
+	return (info->size);
+}
+
+/*-----------------------------------------------------------------------
+ */
+ulong flash_init (void)
+{
+	ulong size = 0;
+	int i;
+
+	/* Init: no FLASHes known */
+	for (i = 0; i < CFG_MAX_FLASH_BANKS; ++i) {
+		flash_info[i].flash_id = FLASH_UNKNOWN;
+	}
+
+	/* Static FLASH Bank configuration here (only one bank) */
+	size = flash_get_size (CFG_FLASH_BASE, &flash_info[0]);
+
+	if (flash_info[0].flash_id == FLASH_UNKNOWN || size == 0) {
+		printf ("## Unknown FLASH on Bank 0 - Size = 0x%08lx = %ld MB\n",
+			size, size >> 20);
+	}
+
+	/*
+	 * protect monitor and environment sectors
+	 */
+	flash_protect (FLAG_PROTECT_SET,
+		       CFG_FLASH_BASE,
+		       CFG_FLASH_BASE + monitor_flash_len - 1,
+		       &flash_info[0]);
+
+	flash_protect (FLAG_PROTECT_SET,
+		       CFG_ENV_ADDR,
+		       CFG_ENV_ADDR + CFG_ENV_SIZE - 1, &flash_info[0]);
+
+	return size;
+}
+
+/*-----------------------------------------------------------------------
+ */
+void flash_print_info (flash_info_t * info)
+{
+	int i;
+
+	if (info->flash_id == FLASH_UNKNOWN) {
+		printf ("missing or unknown FLASH type\n");
+		return;
+	}
+
+	switch (info->flash_id & FLASH_VENDMASK) {
+	case FLASH_MAN_AMD:
+		printf ("AMD ");
+		break;
+	case FLASH_MAN_FUJ:
+		printf ("Fujitsu ");
+		break;
+	default:
+		printf ("Unknown Vendor ");
+		break;
+	}
+
+	switch (info->flash_id & FLASH_TYPEMASK) {
+	case FLASH_AMDL323B:
+		printf ("29DL323B (32 M, bottom sector)\n");
+		break;
+	case (FLASH_AM160LV | FLASH_AM160B):
+		printf ("29LV160BE (1M x 16, bottom sector)\n");
+		break;
+	default:
+		printf ("Unknown Chip Type\n");
+		break;
+	}
+
+	printf ("  Size: %ld MB in %d Sectors\n",
+		info->size >> 20, info->sector_count);
+	printf ("  Sector Start Addresses:");
+	for (i = 0; i < info->sector_count; i++) {
+		if ((i % 4) == 0)
+			printf ("\n   ");
+		printf (" S%02d @ 0x%08lX%s", i,
+			info->start[i], info->protect[i] ? " !" : "  ");
+	}
+	printf ("\n");
+	return;
+}
+
+/*-----------------------------------------------------------------------
+ */
+int flash_check_protection (flash_info_t * info, int s_first, int s_last)
+{
+	int sect, prot = 0;
+
+	for (sect = s_first; sect <= s_last; sect++)
+		if (info->protect[sect])
+			prot++;
+	if (prot)
+		printf ("- can't erase %d protected sectors\n", prot);
+	return prot;
+}
+
+/*-----------------------------------------------------------------------
+ */
+int flash_check_erase_amd (ulong start)
+{
+	__u16 v1, v2;
+
+	v1 = *(volatile __u16 *) (start);
+	v2 = *(volatile __u16 *) (start);
+
+	if (((v1 ^ v2) & toggling_bits) == toggling_bits) {
+		if (((v1 | v2) & DQ5) == DQ5) {
+			printf ("[DQ5] ");
+			/* OOPS: exceeded timing limits */
+
+			v1 = *(volatile __u16 *) (start);
+			v2 = *(volatile __u16 *) (start);
+
+			if (((v1 ^ v2) & toggling_bits) == toggling_bits) {
+
+				printf ("[%s] ",
+					((toggling_bits & (DQ2 | DQ6)) ==
+					 (DQ2 | DQ6)) ? "DQ2,DQ6" : "DQ6");
+
+				/* OOPS: there is an erasure in progress,
+				 *       try to reset chip */
+				*(volatile __u16 *) (start) =
+					(__u16) RESET_CMD;
+
+				return 1;	/* still busy */
+			}
+		}
+		return 1;	/* still busy */
+	}
+	return 0;		/* be free */
+}
+
+/*-----------------------------------------------------------------------
+ */
+int flash_erase (flash_info_t * info, int s_first, int s_last)
+{
+	int flag, sect, setup_offset = 0;
+	int rc = ERR_OK;
+
+	if (info->flash_id == FLASH_UNKNOWN) {
+		printf ("- missing\n");
+		return ERR_UNKNOWN_FLASH_TYPE;
+	}
+
+	if ((s_first < 0) || (s_first > s_last)) {
+		printf ("- no sectors to erase\n");
+		return ERR_INVAL;
+	}
+
+	if (flash_check_protection (info, s_first, s_last))
+		return ERR_PROTECTED;
+
+	switch (info->flash_id & FLASH_VENDMASK) {
+	case FLASH_MAN_FUJ:
+	case FLASH_MAN_AMD:
+		switch (info->flash_id & FLASH_TYPEMASK) {
+		case (FLASH_AM160LV | FLASH_AM160B):
+			setup_offset = UNLOCK_ADDR1;	/* just the adress for setup_cmd differs */
+		case FLASH_AMDL323B:
+			/*
+			 * Disable interrupts which might cause a timeout
+			 * here. Remember that our exception vectors are
+			 * at address 0 in the flash, and we don't want a
+			 * (ticker) exception to happen while the flash
+			 * chip is in programming mode.
+			 */
+			flag = disable_interrupts ();
+			/* Start erase on unprotected sectors */
+			for (sect = s_first; sect <= s_last && !ctrlc ();
+			     sect++) {
+				printf ("Erasing sector %2d ... ", sect);
+
+				if (info->protect[sect] == 0) {
+					/* not protected */
+					/* Write sector erase command sequence */
+					WRITE_UNLOCK (info->start[0]);
+					*(volatile __u16 *) (info->start[0] +
+							     setup_offset) =
+						(__u16) SETUP_CMD;
+					WRITE_UNLOCK (info->start[0]);
+					*(volatile __u16 *) (info->
+							     start[sect]) =
+						(__u16) SECERASE_CMD;
+
+					/* wait some time */
+					reset_timer_masked ();
+					while (get_timer_masked () < 1000) {
+					}
+
+					/* arm simple, non interrupt dependent timer */
+					reset_timer_masked ();
+					while (flash_check_erase_amd (info->start[sect])) {
+						if (get_timer_masked () > CFG_FLASH_ERASE_TOUT) {
+							printf ("timeout!\n");
+							/* OOPS: reach timeout,
+							 * try to reset chip
+							 */
+							*(volatile __u16 *) (info-> start[sect]) = (__u16) RESET_CMD;
+							rc = ERR_TIMOUT;
+							goto outahere_323B;
+						}
+					}
+					printf ("ok.\n");
+				} else {
+					printf ("protected!\n");
+				}
+			}
+			if (ctrlc ())
+				printf ("User Interrupt!\n");
+outahere_323B:
+			/* allow flash to settle - wait 10 ms */
+			udelay_masked (10000);
+			if (flag)
+				enable_interrupts ();
+			return rc;
+		default:
+			printf ("- unknown chip type\n");
+			return ERR_UNKNOWN_FLASH_TYPE;
+		}
+		break;
+	default:
+		printf ("- unknown vendor ");
+		return ERR_UNKNOWN_FLASH_VENDOR;
+	}
+}
+
+/*-----------------------------------------------------------------------
+ */
+int flash_check_write_amd (ulong dest)
+{
+	__u16 v1, v2;
+
+	v1 = *(volatile __u16 *) (dest);
+	v2 = *(volatile __u16 *) (dest);
+
+	/* DQ6 toggles during write */
+	if (((v1 ^ v2) & DQ6) == DQ6) {
+		if (((v1 | v2) & DQ5) == DQ5) {
+			printf ("[DQ5] @ %08lX\n", dest);
+
+			/* OOPS: exceeded timing limits,
+			 *       try to reset chip */
+			*(volatile __u16 *) (dest) = (__u16) RESET_CMD;
+			return 0;	/* be free */
+		}
+		return 1;	/* still busy */
+	}
+
+	return 0;		/* be free */
+}
+
+/*-----------------------------------------------------------------------
+ * Copy memory to flash
+ */
+static int write_word (flash_info_t * info, ulong dest, ushort data)
+{
+	int rc = ERR_OK;
+	int flag;
+
+	/* Check if Flash is (sufficiently) erased */
+	if ((*(__u16 *) (dest) & data) != data)
+		return ERR_NOT_ERASED;
+
+	/*
+	 * Disable interrupts which might cause a timeout
+	 * here. Remember that our exception vectors are
+	 * at address 0 in the flash, and we don't want a
+	 * (ticker) exception to happen while the flash
+	 * chip is in programming mode.
+	 */
+	flag = disable_interrupts ();
+
+	/* Write program command sequence */
+	WRITE_UNLOCK (info->start[0]);
+
+	/* Flash dependend program seqence */
+	switch (info->flash_id & FLASH_VENDMASK) {
+	case FLASH_MAN_FUJ:
+	case FLASH_MAN_AMD:
+		switch (info->flash_id & FLASH_TYPEMASK) {
+		case (FLASH_AM160LV | FLASH_AM160B):
+			*(volatile __u16 *) (info->start[0] + UNLOCK_ADDR1) =
+				(__u16) PROG_CMD;
+			*(volatile __u16 *) (dest) = (__u16) data;
+			break;
+		case FLASH_AMDL323B:
+			*(volatile __u16 *) (dest) = (__u16) PROG_CMD;
+			*(volatile __u16 *) (dest) = (__u16) data;
+			break;
+		}
+	}
+
+	/* arm simple, non interrupt dependent timer */
+	reset_timer_masked ();
+
+	while (flash_check_write_amd (dest)) {
+		if (get_timer_masked () > CFG_FLASH_WRITE_TOUT) {
+			printf ("timeout! @ %08lX\n", dest);
+			/* OOPS: reach timeout,
+			 *       try to reset chip */
+			*(volatile __u16 *) (dest) = (__u16) RESET_CMD;
+
+			rc = ERR_TIMOUT;
+			goto outahere_323B;
+		}
+	}
+
+	/* Check if Flash was (accurately) written */
+	if (*(__u16 *) (dest) != data)
+		rc = ERR_PROG_ERROR;
+
+outahere_323B:
+	if (flag)
+		enable_interrupts ();
+	return rc;
+}
+
+/*-----------------------------------------------------------------------
+ * Copy memory to flash.
+ */
+int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt)
+{
+	ulong cp, wp;
+	ushort data;
+	int l;
+	int i, rc;
+
+	wp = (addr & ~1);	/* get lower word aligned address */
+
+	/*
+	 * handle unaligned start bytes
+	 */
+	if ((l = addr - wp) != 0) {
+		data = 0;
+		for (i = 0, cp = wp; i < l; ++i, ++cp) {
+			data = (data >> 8) | (*(uchar *) cp << 8);
+		}
+		for (; i < 2 && cnt > 0; ++i) {
+			data = (data >> 8) | (*src++ << 8);
+			--cnt;
+			++cp;
+		}
+		for (; cnt == 0 && i < 2; ++i, ++cp) {
+			data = (data >> 8) | (*(uchar *) cp << 8);
+		}
+
+		if ((rc = write_word (info, wp, data)) != 0) {
+			return (rc);
+		}
+		wp += 2;
+	}
+
+	/*
+	 * handle word aligned part
+	 */
+	while (cnt >= 2) {
+		data = *((ushort *) src);
+		if ((rc = write_word (info, wp, data)) != 0)
+			return (rc);
+		src += 2;
+		wp += 2;
+		cnt -= 2;
+	}
+
+	if (cnt == 0)
+		return ERR_OK;
+
+	/*
+	 * handle unaligned tail bytes
+	 */
+	data = 0;
+	for (i = 0, cp = wp; i < 2 && cnt > 0; ++i, ++cp) {
+		data = (data >> 8) | (*src++ << 8);
+		--cnt;
+	}
+	for (; i < 2; ++i, ++cp) {
+		data = (data >> 8) | (*(uchar *) cp << 8);
+	}
+
+	return write_word (info, wp, data);
+}
--- a/board/modnet50/memsetup.S
+++ b/board/modnet50/memsetup.S
@@ -0,0 +1,204 @@
+/*
+ * Memory Setup stuff - taken from Linux
+ *
+ * Copyright (c) 2002	Stephan Linz <linz@mazet.de>, <linz@li-pro.net>
+ * (c) 2004 IMMS gGmbH <www.imms.de>, Thomas Elste <info@elste.org>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+
+#include <config.h>
+#include <version.h>
+#include <asm/arch/netarm_registers.h>
+
+
+/* some parameters for the board */
+#define FLASH_90ns_WAIT_STATES	((NETARM_PLL_COUNT_VAL + 2) / 3)
+#define FLASH_70ns_WAIT_STATES	4
+
+#define NETARM_MMAP_CS0_BASE	(PHYS_FLASH_1)
+#if 1
+#define NETARM_MMAP_CS0_MASK	(~(PHYS_FLASH_1_SIZE - 1))
+#else
+#define NETARM_MMAP_CS0_MASK	(~(1000000 - 1))
+#endif
+#define NETARM_MMAP_CS1_BASE	(PHYS_SDRAM_1)
+#define NETARM_MMAP_CS1_MASK	(~(PHYS_SDRAM_1_SIZE - 1))
+#define NETARM_MMAP_CS2_BASE	(PHYS_SDRAM_2)
+#define NETARM_MMAP_CS2_MASK	(~(PHYS_SDRAM_2_SIZE - 1))
+#if defined(CONFIG_NETARM_EEPROM) && defined(PHYS_NVRAM_1) && defined(PHYS_NVRAM_SIZE)
+#define NETARM_MMAP_CS3_BASE	(PHYS_NVRAM_1)
+#define NETARM_MMAP_CS3_MASK	(~(PHYS_NVRAM_SIZE - 1))
+#endif
+#define NETARM_MMAP_CS4_BASE	(PHYS_EXT_1)
+#define NETARM_MMAP_CS4_MASK	(~(PHYS_EXT_SIZE - 1))
+
+/* setting up the memory */
+.globl memsetup
+memsetup:
+
+#if defined(CONFIG_MODNET50)
+	ldr	pc, =(_jump_to_high + NETARM_MMAP_CS0_BASE - TEXT_BASE)
+
+_jump_to_high:
+	/*
+	 * MEM Config Reg
+	 * ---------------------------------------------------
+	 */
+	ldr	r0, =NETARM_MEM_MODULE_BASE
+	ldr	r1, =(	NETARM_MEM_REFR_PERIOD_USEC(16) | \
+			NETARM_MEM_CFG_REFRESH_EN | \
+			NETARM_MEM_CFG_REFR_CYCLE_5CLKS )
+	str	r1, [r0, #+NETARM_MEM_MODULE_CONFIG]
+
+
+memsetup_cs0:
+	/*
+	 * Base Addr / Option Reg 0 (Flash)
+	 * ---------------------------------------------------
+	 */
+	ldr	r1, =(	NETARM_MEM_BAR_BASE(NETARM_MMAP_CS0_BASE) | \
+			NETARM_MEM_BAR_DRAM_FP | \
+			NETARM_MEM_BAR_DRAM_MUX_INT | \
+			NETARM_MEM_BAR_DRAM_MUX_BAL | \
+			NETARM_MEM_BAR_VALID )
+	str	r1, [r0, #+NETARM_MEM_CS0_BASE_ADDR]
+
+	/* trust that the bus size for flash was strapped correctly */
+	/* this saves the bus width in r2 and then ORs it back in */
+	/* it's pretty safe assumption, otherwise it wouldn't boot */
+	ldr	r2, [r0, #+NETARM_MEM_CS0_OPTIONS]
+	and	r2, r2, #NETARM_MEM_OPT_BUS_SIZE_MASK
+
+/*	just a test: assume 32 bit flash mem */
+/*	mov	r2, #NETARM_MEM_OPT_32BIT */
+
+	ldr	r1, =(	NETARM_MEM_OPT_BASE_USE(NETARM_MMAP_CS0_MASK) | \
+			NETARM_MEM_OPT_WAIT_STATES(FLASH_70ns_WAIT_STATES) | \
+			NETARM_MEM_OPT_BCYC_4 | \
+			NETARM_MEM_OPT_BSIZE_16 | \
+			NETARM_MEM_OPT_16BIT | \
+			NETARM_MEM_OPT_READ_ASYNC | \
+			NETARM_MEM_OPT_WRITE_ASYNC )
+
+	orr	r1, r1, r2
+	str	r1, [r0, #+NETARM_MEM_CS0_OPTIONS]
+
+
+memsetup_cs1:
+	/*
+	 * Base Addr / Option Reg 1 (DRAM #1)
+	 * ---------------------------------------------------
+	 */
+#ifdef CONFIG_NETARM_NET40_REV2
+	/* we have to config SDRAM in burst mode */
+	ldr	r1, =(	NETARM_MEM_OPT_BASE_USE(NETARM_MMAP_CS1_MASK) | \
+			NETARM_MEM_OPT_BCYC_2 | \
+			NETARM_MEM_OPT_BSIZE_16 | \
+			NETARM_MEM_OPT_WAIT_STATES(0) | \
+			NETARM_MEM_OPT_32BIT | \
+			NETARM_MEM_OPT_READ_ASYNC | \
+			NETARM_MEM_OPT_WRITE_ASYNC )
+	str	r1, [r0, #+NETARM_MEM_CS1_OPTIONS]
+
+	ldr	r1, =(	NETARM_MEM_BAR_BASE(NETARM_MMAP_CS1_BASE) | \
+			NETARM_MEM_BAR_DRAM_SYNC | \
+			NETARM_MEM_BAR_DRAM_MUX_INT | \
+			NETARM_MEM_BAR_DRAM_MUX_UNBAL | \
+			NETARM_MEM_BAR_DRAM_SEL | \
+			NETARM_MEM_BAR_BURST_EN | \
+			NETARM_MEM_BAR_VALID )
+	str	r1, [r0, #+NETARM_MEM_CS1_BASE_ADDR]
+#else
+	/* we have to config FPDRAM in burst mode with smaller burst access size */
+	ldr	r1, =(	NETARM_MEM_OPT_BASE_USE(NETARM_MMAP_CS1_MASK) | \
+			NETARM_MEM_OPT_BCYC_2 | \
+			NETARM_MEM_OPT_BSIZE_16 | \
+			NETARM_MEM_OPT_WAIT_STATES(0) | \
+			NETARM_MEM_OPT_32BIT | \
+			NETARM_MEM_OPT_READ_ASYNC | \
+			NETARM_MEM_OPT_WRITE_ASYNC )
+	str	r1, [r0, #+NETARM_MEM_CS1_OPTIONS]
+
+	ldr	r1, =(	NETARM_MEM_BAR_BASE(NETARM_MMAP_CS1_BASE) | \
+			NETARM_MEM_BAR_DRAM_SYNC | \
+			NETARM_MEM_BAR_DRAM_MUX_INT | \
+			NETARM_MEM_BAR_DRAM_MUX_UNBAL | \
+			NETARM_MEM_BAR_DRAM_SEL | \
+			NETARM_MEM_BAR_BURST_EN | \
+			NETARM_MEM_BAR_VALID )
+	str	r1, [r0, #+NETARM_MEM_CS1_BASE_ADDR]
+
+#endif /* CONFIG_NETARM_NET40_REV2 */
+
+
+memsetup_cs3:
+	/*
+	 * Base Addr / Option Reg 3 (EEPROM, NVRAM)
+	 * ---------------------------------------------------
+	 */
+#if defined(CONFIG_NETARM_EEPROM) && defined(PHYS_NVRAM_1) && defined(PHYS_NVRAM_SIZE)
+	ldr	r1, =(	NETARM_MEM_OPT_BASE_USE(NETARM_MMAP_CS3_MASK) | \
+			NETARM_MEM_OPT_BCYC_3 | \
+			NETARM_MEM_OPT_BSIZE_2 | \
+			NETARM_MEM_OPT_WAIT_STATES(10) | \
+			NETARM_MEM_OPT_8BIT | \
+			NETARM_MEM_OPT_READ_ASYNC | \
+			NETARM_MEM_OPT_WRITE_ASYNC )
+	str	r1, [r0, #+NETARM_MEM_CS3_OPTIONS]
+
+	ldr	r1, =(	NETARM_MEM_BAR_BASE(NETARM_MMAP_CS3_BASE) | \
+			NETARM_MEM_BAR_DRAM_FP | \
+			NETARM_MEM_BAR_DRAM_MUX_INT | \
+			NETARM_MEM_BAR_DRAM_MUX_BAL | \
+			NETARM_MEM_BAR_VALID )
+	str	r1, [r0, #+NETARM_MEM_CS3_BASE_ADDR]
+#else
+	/* we don't need EEPROM --> no config */
+	ldr	r1, =( 0 )
+	str	r1, [r0, #+NETARM_MEM_CS3_OPTIONS]
+
+	ldr	r1, =( 0 )
+	str	r1, [r0, #+NETARM_MEM_CS3_BASE_ADDR]
+#endif
+
+
+#else
+/*
+#error "missing CONFIG_MODNET50 (see your config.h)"
+*/
+#endif /* CONFIG_MODNET50 */
+
+
+memsetup_end:
+	/*
+	 * manipulate address in lr and ip to match new
+	 * address space
+	 */
+	ldr	r3, =(NETARM_MMAP_CS0_BASE)
+	mov	r0, lr
+	add	r0, r3, r0
+	mov	lr, r0
+	mov	r0, ip
+	add	r0, r3, r0
+	mov	ip, r0
+
+	/* everything is fine now */
+	mov	pc, lr
--- a/board/modnet50/modnet50.c
+++ b/board/modnet50/modnet50.c
@@ -0,0 +1,52 @@
+/*
+ * (C) Copyright 2002
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Marius Groeger <mgroeger@sysgo.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+
+/* ------------------------------------------------------------------------- */
+
+
+/*
+ * Miscelaneous platform dependent initialisations
+ */
+
+int board_init (void)
+{
+	DECLARE_GLOBAL_DATA_PTR;
+	/* address for the kernel command line */
+	gd->bd->bi_boot_params = 0x800;
+	return 0;
+}
+
+int dram_init (void)
+{
+	DECLARE_GLOBAL_DATA_PTR;
+	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
+	if (CONFIG_NR_DRAM_BANKS == 2) {
+		gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
+		gd->bd->bi_dram[1].size = PHYS_SDRAM_2_SIZE;
+	}
+	return (0);
+}
--- a/board/modnet50/u-boot.lds
+++ b/board/modnet50/u-boot.lds
@@ -0,0 +1,68 @@
+/*
+ * (C) Copyright 2000-2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+	. = 0x00000000;
+
+	. = ALIGN(4);
+	.text	   :
+	{
+	  cpu/arm720t/start.o	(.text)
+	  *(.text)
+	}
+
+	. = ALIGN(4);
+	.rodata : { *(.rodata) }
+
+	. = ALIGN(4);
+	.data : { *(.data) }
+
+	. = ALIGN(4);
+	.got : { *(.got) }
+
+	__u_boot_cmd_start = .;
+	.u_boot_cmd : { *(.u_boot_cmd) }
+	__u_boot_cmd_end = .;
+
+	. = ALIGN(4);
+	__bss_start = .;
+	.bss : { *(.bss) }
+	_end = .;
+				  /* Stabs debugging sections.	  */
+	.stab 0 : { *(.stab) }
+	.stabstr 0 : { *(.stabstr) }
+	.stab.excl 0 : { *(.stab.excl) }
+	.stab.exclstr 0 : { *(.stab.exclstr) }
+	.stab.index 0 : { *(.stab.index) }
+	.stab.indexstr 0 : { *(.stab.indexstr) }
+	.comment 0 : { *(.comment) }
+	.debug_abbrev 0 : { *(.debug_abbrev) }
+	.debug_info 0 : { *(.debug_info) }
+	.debug_line 0 : { *(.debug_line) }
+	.debug_pubnames 0 : { *(.debug_pubnames) }
+	.debug_aranges 0 : { *(.debug_aranges) }
+}
--- a/board/mpl/common/common_util.c
+++ b/board/mpl/common/common_util.c
@@ -232,7 +232,7 @@ mpl_prg_image(uchar *ld_addr)
 			}
 			puts("OK\n");
 			break;
-#if CONFIG_BZIP2
+#ifdef CONFIG_BZIP2
 		case IH_COMP_BZIP2:
 			puts("Uncompressing (BZIP2) ... ");
 			{
--- a/board/mpl/mip405/mip405.c
+++ b/board/mpl/mip405/mip405.c
@@ -709,6 +709,18 @@ void print_mip405_rev (void)
 			var, pcbrev + 'A', part & 0x7F, vers);
 }

+
+#ifdef CONFIG_POST
+/*
+ * Returns 1 if keys pressed to start the power-on long-running tests
+ * Called from board_init_f().
+ */
+int post_hotkeys_pressed(void)
+{
+	return 0;	/* No hotkeys supported */
+}
+#endif
+
 extern void mem_test_reloc(void);
 extern int mk_date (char *, struct rtc_time *);

--- a/board/ns9750dev/Makefile
+++ b/board/ns9750dev/Makefile
@@ -0,0 +1,47 @@
+#
+# (C) Copyright 2000, 2001, 2002
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	:= ns9750dev.o flash.o led.o
+SOBJS	:= platform.o
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) crv $@ $(OBJS) $(SOBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+-include .depend
+
+#########################################################################
--- a/board/ns9750dev/config.mk
+++ b/board/ns9750dev/config.mk
@@ -0,0 +1,16 @@
+#######################################################################
+#
+# Copyright (C) 2004 by FS Forth-Systeme GmbH.
+# Markus Pietrek <mpietrek@fsforth.de>
+#
+# @TODO
+# Linux-Kernel is expected to be at 0000'8000, entry 0000'8000
+# optionally with a ramdisk at 0080'0000
+#
+# we load ourself to 0078'0000
+#
+# download area is 0060'0000
+#
+
+
+TEXT_BASE = 0x00780000
--- a/board/ns9750dev/flash.c
+++ b/board/ns9750dev/flash.c
@@ -0,0 +1,477 @@
+/*
+ * (C) Copyright 2001
+ * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net
+ *
+ * (C) Copyright 2001
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * (C) Copyright 2003
+ * Texas Instruments, <www.ti.com>
+ * Kshitij Gupta <Kshitij@ti.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <linux/byteorder/swab.h>
+
+#define PHYS_FLASH_SECT_SIZE	0x00020000	/* 256 KB sectors (x2) */
+flash_info_t flash_info[CFG_MAX_FLASH_BANKS];	/* info for FLASH chips    */
+
+/* Board support for 1 or 2 flash devices */
+#undef FLASH_PORT_WIDTH32
+#define FLASH_PORT_WIDTH16
+
+#ifdef FLASH_PORT_WIDTH16
+#define FLASH_PORT_WIDTH		ushort
+#define FLASH_PORT_WIDTHV		vu_short
+#define SWAP(x)			__swab16(x)
+#else
+#define FLASH_PORT_WIDTH		ulong
+#define FLASH_PORT_WIDTHV		vu_long
+#define SWAP(x)			__swab32(x)
+#endif
+
+#define FPW	FLASH_PORT_WIDTH
+#define FPWV	FLASH_PORT_WIDTHV
+
+#define mb() __asm__ __volatile__ ("" : : : "memory")
+
+
+/* Flash Organization Structure */
+typedef struct OrgDef {
+	unsigned int sector_number;
+	unsigned int sector_size;
+} OrgDef;
+
+
+/* Flash Organizations */
+OrgDef OrgIntel_28F256L18T[] = {
+	{4, 32 * 1024},				/* 4 * 32kBytes sectors */
+	{255, 128 * 1024},			/* 255 * 128kBytes sectors */
+};
+
+
+/*-----------------------------------------------------------------------
+ * Functions
+ */
+unsigned long flash_init (void);
+static ulong flash_get_size (FPW * addr, flash_info_t * info);
+static int write_data (flash_info_t * info, ulong dest, FPW data);
+static void flash_get_offsets (ulong base, flash_info_t * info);
+void inline spin_wheel (void);
+void flash_print_info (flash_info_t * info);
+void flash_unprotect_sectors (FPWV * addr);
+int flash_erase (flash_info_t * info, int s_first, int s_last);
+int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt);
+
+/*-----------------------------------------------------------------------
+ */
+
+unsigned long flash_init (void)
+{
+	int i;
+	ulong size = 0;
+	for (i = 0; i < CFG_MAX_FLASH_BANKS; i++) {
+		switch (i) {
+		case 0:
+			flash_get_size ((FPW *) PHYS_FLASH_1, &flash_info[i]);
+			flash_get_offsets (PHYS_FLASH_1, &flash_info[i]);
+			break;
+		default:
+			panic ("configured too many flash banks!\n");
+			break;
+		}
+		size += flash_info[i].size;
+	}
+
+	/* Protect monitor and environment sectors
+	 */
+	flash_protect (FLAG_PROTECT_SET,
+			CFG_FLASH_BASE,
+			CFG_FLASH_BASE + monitor_flash_len - 1, &flash_info[0]);
+
+	flash_protect (FLAG_PROTECT_SET,
+			CFG_ENV_ADDR,
+			CFG_ENV_ADDR + CFG_ENV_SIZE - 1, &flash_info[0]);
+
+	return size;
+}
+
+/*-----------------------------------------------------------------------
+ */
+static void flash_get_offsets (ulong base, flash_info_t * info)
+{
+	int i;
+	OrgDef *pOrgDef;
+
+	pOrgDef = OrgIntel_28F256L18T;
+	if (info->flash_id == FLASH_UNKNOWN) {
+		return;
+	}
+
+	if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL) {
+		for (i = 0; i < info->sector_count; i++) {
+			if (i > 255) {
+				info->start[i] = base + (i * 0x8000);
+				info->protect[i] = 0;
+			} else {
+				info->start[i] = base +
+						(i * PHYS_FLASH_SECT_SIZE);
+				info->protect[i] = 0;
+			}
+		}
+	}
+}
+
+/*-----------------------------------------------------------------------
+ */
+void flash_print_info (flash_info_t * info)
+{
+	int i;
+
+	if (info->flash_id == FLASH_UNKNOWN) {
+		printf ("missing or unknown FLASH type\n");
+		return;
+	}
+
+	switch (info->flash_id & FLASH_VENDMASK) {
+	case FLASH_MAN_INTEL:
+		printf ("INTEL ");
+		break;
+	default:
+		printf ("Unknown Vendor ");
+		break;
+	}
+
+	switch (info->flash_id & FLASH_TYPEMASK) {
+	case FLASH_28F256L18T:
+		printf ("FLASH 28F256L18T\n");
+		break;
+	default:
+		printf ("Unknown Chip Type\n");
+		break;
+	}
+
+	printf ("  Size: %ld MB in %d Sectors\n",
+			info->size >> 20, info->sector_count);
+
+	printf ("  Sector Start Addresses:");
+	for (i = 0; i < info->sector_count; ++i) {
+		if ((i % 5) == 0)
+			printf ("\n   ");
+		printf (" %08lX%s",
+			info->start[i], info->protect[i] ? " (RO)" : "     ");
+	}
+	printf ("\n");
+	return;
+}
+
+/*
+ * The following code cannot be run from FLASH!
+ */
+static ulong flash_get_size (FPW * addr, flash_info_t * info)
+{
+	volatile FPW value;
+
+	/* Write auto select command: read Manufacturer ID */
+	addr[0x5555] = (FPW) 0x00AA00AA;
+	addr[0x2AAA] = (FPW) 0x00550055;
+	addr[0x5555] = (FPW) 0x00900090;
+
+	mb ();
+	value = addr[0];
+
+	switch (value) {
+
+	case (FPW) INTEL_MANUFACT:
+		info->flash_id = FLASH_MAN_INTEL;
+		break;
+
+	default:
+		info->flash_id = FLASH_UNKNOWN;
+		info->sector_count = 0;
+		info->size = 0;
+		addr[0] = (FPW) 0x00FF00FF;	/* restore read mode */
+		return (0);		/* no or unknown flash  */
+	}
+
+	mb ();
+	value = addr[1];	/* device ID        */
+	switch (value) {
+
+	case (FPW) (INTEL_ID_28F256L18T):
+		info->flash_id += FLASH_28F256L18T;
+		info->sector_count = 259;
+		info->size = 0x02000000;
+		break;			/* => 32 MB     */
+
+	default:
+		info->flash_id = FLASH_UNKNOWN;
+		break;
+	}
+
+	if (info->sector_count > CFG_MAX_FLASH_SECT) {
+		printf ("** ERROR: sector count %d > max (%d) **\n",
+				info->sector_count, CFG_MAX_FLASH_SECT);
+		info->sector_count = CFG_MAX_FLASH_SECT;
+	}
+
+	addr[0] = (FPW) 0x00FF00FF;	/* restore read mode */
+
+	return (info->size);
+}
+
+
+/* unprotects a sector for write and erase
+ * on some intel parts, this unprotects the entire chip, but it
+ * wont hurt to call this additional times per sector...
+ */
+void flash_unprotect_sectors (FPWV * addr)
+{
+#define PD_FINTEL_WSMS_READY_MASK    0x0080
+
+	*addr = (FPW) 0x00500050;	/* clear status register */
+
+	/* this sends the clear lock bit command */
+	*addr = (FPW) 0x00600060;
+	*addr = (FPW) 0x00D000D0;
+}
+
+
+/*-----------------------------------------------------------------------
+ */
+
+int flash_erase (flash_info_t * info, int s_first, int s_last)
+{
+	int flag, prot, sect;
+	ulong type, start, last;
+	int rcode = 0;
+
+	if ((s_first < 0) || (s_first > s_last)) {
+		if (info->flash_id == FLASH_UNKNOWN) {
+			printf ("- missing\n");
+		} else {
+			printf ("- no sectors to erase\n");
+		}
+		return 1;
+	}
+
+	type = (info->flash_id & FLASH_VENDMASK);
+	if ((type != FLASH_MAN_INTEL)) {
+		printf ("Can't erase unknown flash type %08lx - aborted\n",
+				info->flash_id);
+		return 1;
+	}
+
+	prot = 0;
+	for (sect = s_first; sect <= s_last; ++sect) {
+		if (info->protect[sect]) {
+			prot++;
+		}
+	}
+
+	if (prot) {
+		printf ("- Warning: %d protected sectors will not be erased!\n",
+				prot);
+	} else {
+		printf ("\n");
+	}
+
+
+	start = get_timer (0);
+	last = start;
+
+	/* Disable interrupts which might cause a timeout here */
+	flag = disable_interrupts ();
+
+	/* Start erase on unprotected sectors */
+	for (sect = s_first; sect <= s_last; sect++) {
+		if (info->protect[sect] == 0) {	/* not protected */
+			FPWV *addr = (FPWV *) (info->start[sect]);
+			FPW status;
+
+			printf ("Erasing sector %2d ... ", sect);
+
+			flash_unprotect_sectors (addr);
+
+			/* arm simple, non interrupt dependent timer */
+			reset_timer_masked ();
+
+			*addr = (FPW) 0x00500050;/* clear status register */
+			*addr = (FPW) 0x00200020;/* erase setup */
+			*addr = (FPW) 0x00D000D0;/* erase confirm */
+
+			while (((status =
+				*addr) & (FPW) 0x00800080) !=
+				(FPW) 0x00800080) {
+					if (get_timer_masked () >
+					CFG_FLASH_ERASE_TOUT) {
+					printf ("Timeout\n");
+					/* suspend erase     */
+					*addr = (FPW) 0x00B000B0;
+					/* reset to read mode */
+					*addr = (FPW) 0x00FF00FF;
+					rcode = 1;
+					break;
+				}
+			}
+
+			/* clear status register cmd.   */
+			*addr = (FPW) 0x00500050;
+			*addr = (FPW) 0x00FF00FF;/* resest to read mode */
+			printf (" done\n");
+		}
+	}
+	return rcode;
+}
+
+/*-----------------------------------------------------------------------
+ * Copy memory to flash, returns:
+ * 0 - OK
+ * 1 - write timeout
+ * 2 - Flash not erased
+ * 4 - Flash not identified
+ */
+
+int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt)
+{
+	ulong cp, wp;
+	FPW data;
+	int count, i, l, rc, port_width;
+
+	if (info->flash_id == FLASH_UNKNOWN) {
+		return 4;
+	}
+/* get lower word aligned address */
+#ifdef FLASH_PORT_WIDTH16
+	wp = (addr & ~1);
+	port_width = 2;
+#else
+	wp = (addr & ~3);
+	port_width = 4;
+#endif
+
+	/*
+	 * handle unaligned start bytes
+	 */
+	if ((l = addr - wp) != 0) {
+		data = 0;
+		for (i = 0, cp = wp; i < l; ++i, ++cp) {
+			data = (data << 8) | (*(uchar *) cp);
+		}
+		for (; i < port_width && cnt > 0; ++i) {
+			data = (data << 8) | *src++;
+			--cnt;
+			++cp;
+		}
+		for (; cnt == 0 && i < port_width; ++i, ++cp) {
+			data = (data << 8) | (*(uchar *) cp);
+		}
+
+		if ((rc = write_data (info, wp, SWAP (data))) != 0) {
+			return (rc);
+		}
+		wp += port_width;
+	}
+
+	/*
+	 * handle word aligned part
+	 */
+	count = 0;
+	while (cnt >= port_width) {
+		data = 0;
+		for (i = 0; i < port_width; ++i) {
+			data = (data << 8) | *src++;
+		}
+		if ((rc = write_data (info, wp, SWAP (data))) != 0) {
+			return (rc);
+		}
+		wp += port_width;
+		cnt -= port_width;
+		if (count++ > 0x800) {
+			spin_wheel ();
+			count = 0;
+		}
+	}
+
+	if (cnt == 0) {
+		return (0);
+	}
+
+	/*
+	 * handle unaligned tail bytes
+	 */
+	data = 0;
+	for (i = 0, cp = wp; i < port_width && cnt > 0; ++i, ++cp) {
+		data = (data << 8) | *src++;
+		--cnt;
+	}
+	for (; i < port_width; ++i, ++cp) {
+		data = (data << 8) | (*(uchar *) cp);
+	}
+
+	return (write_data (info, wp, SWAP (data)));
+}
+
+/*-----------------------------------------------------------------------
+ * Write a word or halfword to Flash, returns:
+ * 0 - OK
+ * 1 - write timeout
+ * 2 - Flash not erased
+ */
+static int write_data (flash_info_t * info, ulong dest, FPW data)
+{
+	FPWV *addr = (FPWV *) dest;
+	ulong status;
+	int flag;
+
+	/* Check if Flash is (sufficiently) erased */
+	if ((*addr & data) != data) {
+		printf ("not erased at %08lx (%x)\n", (ulong) addr, *addr);
+		return (2);
+	}
+	flash_unprotect_sectors (addr);
+	/* Disable interrupts which might cause a timeout here */
+	flag = disable_interrupts ();
+	*addr = (FPW) 0x00400040;	/* write setup */
+	*addr = data;
+
+	/* arm simple, non interrupt dependent timer */
+	reset_timer_masked ();
+
+	/* wait while polling the status register */
+	while (((status = *addr) & (FPW) 0x00800080) != (FPW) 0x00800080) {
+		if (get_timer_masked () > CFG_FLASH_WRITE_TOUT) {
+			*addr = (FPW) 0x00FF00FF;	/* restore read mode */
+			return (1);
+		}
+	}
+	*addr = (FPW) 0x00FF00FF;	/* restore read mode */
+	return (0);
+}
+
+void inline spin_wheel (void)
+{
+	static int p = 0;
+	static char w[] = "\\/-";
+
+	printf ("\010%c", w[p]);
+	(++p == 3) ? (p = 0) : 0;
+}
--- a/board/ns9750dev/led.c
+++ b/board/ns9750dev/led.c
@@ -0,0 +1,46 @@
+/***********************************************************************
+ *
+ * Copyright (C) 2004 by FS Forth-Systeme GmbH.
+ * All rights reserved.
+ *
+ * $Id: led.c,v 1.1 2004/02/16 10:37:20 mpietrek Exp $
+ * @Author: Markus Pietrek
+ * @Descr: Defines helper functions for toggeling LEDs
+ * @Usage:
+ * @References: [1]
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ ***********************************************************************/
+
+#ifdef CONFIG_STATUS_LED
+
+#include <ns9750_bbus.h>
+
+static inline void __led_init( led_id_t mask, int state )
+{
+	XXXX;
+}
+
+static inline void __led_toggle( led_id_t mask )
+{
+}
+
+static inline void __led_set( led_id_t mask, int state )
+{
+}
+
+#endif /* CONFIG_STATUS_LED */
--- a/board/ns9750dev/ns9750dev.c
+++ b/board/ns9750dev/ns9750dev.c
@@ -0,0 +1,127 @@
+/*
+ * (C) Copyright 2002
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Marius Groeger <mgroeger@sysgo.de>
+ *
+ * (C) Copyright 2002
+ * David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
+ *
+ * (C) Copyright 2003
+ * Texas Instruments, <www.ti.com>
+ * Kshitij Gupta <Kshitij@ti.com>
+ *
+ * Copyright (C) 2004 by FS Forth-Systeme GmbH.
+ * All rights reserved.
+ * Markus Pietrek <mpietrek@fsforth.de>
+ * derived from omap1610innovator.c
+ * @References: [1] NS9750 Hardware Reference/December 2003
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#if defined(CONFIG_NS9750DEV)
+# include <./configs/ns9750dev.h>
+# include <./ns9750_bbus.h>
+#endif
+
+void flash__init( void );
+void ether__init( void );
+
+static inline void delay( unsigned long loops )
+{
+	__asm__ volatile ("1:\n"
+		"subs %0, %1, #1\n"
+		"bne 1b":"=r" (loops):"0" (loops));
+}
+
+
+/***********************************************************************
+ * @Function: board_init
+ * @Return: 0
+ * @Descr: Enables BBUS modules and other devices
+ ***********************************************************************/
+
+int board_init( void )
+{
+	DECLARE_GLOBAL_DATA_PTR;
+
+	/* Active BBUS modules */
+	*get_bbus_reg_addr( NS9750_BBUS_MASTER_RESET ) = 0;
+
+#warning TODO check numbers
+	/* arch number of OMAP 1510-Board */
+	/* to be changed for OMAP 1610 Board */
+	gd->bd->bi_arch_number = 234;
+
+	/* adress of boot parameters */
+	gd->bd->bi_boot_params = 0x10000100;
+
+
+/* this speeds up your boot a quite a bit.  However to make it
+ *  work, you need make sure your kernel startup flush bug is fixed.
+ *  ... rkw ...
+ */
+	icache_enable();
+
+	flash__init();
+	ether__init();
+	return 0;
+}
+
+
+int misc_init_r (void)
+{
+	/* currently empty */
+	return (0);
+}
+
+/******************************
+ Routine:
+ Description:
+******************************/
+void flash__init (void)
+{
+}
+/*************************************************************
+ Routine:ether__init
+ Description: take the Ethernet controller out of reset and wait
+	  		   for the EEPROM load to complete.
+*************************************************************/
+void ether__init (void)
+{
+}
+
+/******************************
+ Routine:
+ Description:
+******************************/
+int dram_init (void)
+{
+	DECLARE_GLOBAL_DATA_PTR;
+
+	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
+
+#if CONFIG_NR_DRAM_BANKS > 1
+	gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
+	gd->bd->bi_dram[1].size = PHYS_SDRAM_2_SIZE;
+#endif
+	return 0;
+}
--- a/board/ns9750dev/platform.S
+++ b/board/ns9750dev/platform.S
@@ -0,0 +1,298 @@
+/*
+ * Board specific setup info
+ *
+ * (C) Copyright 2003
+ * Texas Instruments, <www.ti.com>
+ * Kshitij Gupta <Kshitij@ti.com>
+ *
+ * Modified for the NS9750 DevBoard by
+ * (C) Copyright 2004 by FS Forth-Systeme GmbH.
+ * Markus Pietrek <mpietrek@fsforth.de>
+ * @References: [1] NS9750 Hardware Reference/December 2003
+ *	        [2] ns9750_a.cmd from MAJIC configuration
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <version.h>
+
+#if defined(CONFIG_NS9750DEV)
+# ifdef CONFIG_INIT_CRITICAL
+#  include <./ns9750_sys.h>
+#  include <./ns9750_mem.h>
+# endif
+#endif
+
+/***********************************************************************
+ * @Function: write_register_block
+ * @Return: nothing
+ * @Descr: Copies the register block of register_offset:register value to
+ *         the registers at base r0. The block is assumed to start in RAM at r1
+ *         and end at r2. The linked RAM base address of U-Boot is assumed to be
+ *	   in r5 while the ROM base address we are running from is r6
+ *         Uses r3 and r4 as tempory registers
+ ***********************************************************************/
+
+.macro	write_register_block
+	@@ map the addresses to high memory
+	sub	r1, r1, r5
+	add	r1, r1, r6
+	sub	r2, r2, r5
+	add	r2, r2, r6
+
+	@@ copy all
+1:
+	@@ Write register/value pair starting at [r1] to register base r0
+	ldr	r3, [r1], #4
+	ldr	r4, [r1], #4
+	str	r4, [r0,r3]
+	cmp	r1, r2
+	blt	1b
+.endm
+
+_TEXT_BASE:
+	.word	TEXT_BASE	@ sdram load addr from config.mk
+_PHYS_FLASH:
+	.word	PHYS_FLASH_1    @ real flash address (without mirroring)
+_CAS_LATENCY:
+	.word	0x00022000	@ for CAS2 latency
+
+#ifdef CONFIG_INIT_CRITICAL
+.globl platformsetup
+platformsetup:
+
+	/* U-Boot may be linked to RAM at 0x780000. But this code will run in
+	   flash from 0x0. But in order to enable RAM we have to disable the
+	   mirror bit, therefore we have to jump to our real flash address
+	   beginning at PHYS_FLASH_1 (CS4 Base). Therefore,
+	   _run_at_real_flash_address may be 0x500003b0 while be linked to
+	   0x7803b0. So we must modify our linked addresses */
+
+	@@ branch to high memory address, away from 0x0
+	ldr	r5, _TEXT_BASE
+	ldr	r6, _PHYS_FLASH
+	ldr	r0, =_run_at_real_flash_address
+	sub	r0, r0, r5
+	add	r0, r0, r6
+	mov	pc, r0
+	nop			@ for pipelining
+
+_run_at_real_flash_address:
+	@@ now we are running > PHYS_FLASH_1, safe to enable memory controller
+
+	@@ Write Memory Configuration Registers
+
+	ldr	r0, _NS9750_MEM_MODULE_BASE
+	ldr	r1, =_MEM_CONFIG_START
+	ldr	r2, =_MEM_CONFIG_END
+
+	write_register_block
+
+	@@ Give SDRAM some time to settle
+	@@ @TODO. According to [2] it should be 2 AHB cycles. Check
+
+	ldr	r1, =0x50
+_sdram_settle:
+	subs	r1, r1, #1
+	bne	_sdram_settle
+
+_enable_mappings:
+	@@ Enable SDRAM Mode
+
+	ldr	r1, =_MEM_MODE_START
+	ldr	r2, =_MEM_MODE_END
+
+	write_register_block
+
+	ldr	r3, _CAS_LATENCY @ perform one read from SDRAM
+	ldr	r3, [r3]
+
+	@@ Enable SDRAM and memory mappings
+
+	ldr	r1, =_MEM_ENABLE_START
+	ldr	r2, =_MEM_ENABLE_END
+
+	write_register_block
+
+	@@ Activate AHB monitor
+
+	ldr	r0, =NS9750_SYS_MODULE_BASE
+	ldr	r1, =_AHB_MONITOR_START
+	ldr	r2, =_AHB_MONITOR_END
+
+	write_register_block
+_relocate_lr:
+	/* lr and ip (from cpu_init_crit) are still based on 0x0, relocate it to
+	   PHYS_FLASH. */
+	mov	r1, ip
+	add	r1, r1, r6
+	mov	ip, r1
+
+	mov	r1, lr
+	add	r1, r1, r6
+	mov	lr, r1
+
+	@@ back to arch calling code
+	mov	pc,	lr
+
+	.ltorg
+
+_NS9750_MEM_MODULE_BASE:
+	.word	NS9750_MEM_MODULE_BASE
+
+_MEM_CONFIG_START:
+	/* Table of 2 32bit entries. First word is register address offset
+	   relative to NS9750_MEM_MODULE_BASE, second one is value. They are
+	   written in order of appearance */
+
+	@@ Register values taken from [2]
+	.word	NS9750_MEM_CTRL
+	.word	NS9750_MEM_CTRL_E
+
+	.word	NS9750_MEM_DYN_REFRESH
+	.word	(0x6 & NS9750_MEM_DYN_REFRESH_MA)
+
+	.word	NS9750_MEM_DYN_READ_CFG
+	.word	(0x1 & NS9750_MEM_DYN_READ_CFG_MA)
+
+	.word	NS9750_MEM_DYN_TRP
+	.word	(0x1 & NS9750_MEM_DYN_TRP_MA)
+
+	.word	NS9750_MEM_DYN_TRAS
+	.word	(0x4 & NS9750_MEM_DYN_TRAS_MA)
+
+	.word	NS9750_MEM_DYN_TAPR
+	.word	(0x1 & NS9750_MEM_DYN_TRAS_MA)
+
+	.word	NS9750_MEM_DYN_TDAL
+	.word	(0x5 & NS9750_MEM_DYN_TDAL_MA)
+
+	.word	NS9750_MEM_DYN_TWR
+	.word	(0x1 & NS9750_MEM_DYN_TWR_MA)
+
+	.word	NS9750_MEM_DYN_TRC
+	.word	(0x6 & NS9750_MEM_DYN_TRC_MA)
+
+	.word	NS9750_MEM_DYN_TRFC
+	.word	(0x6 & NS9750_MEM_DYN_TRFC_MA)
+
+	.word	NS9750_MEM_DYN_TRRD
+	.word	(0x1 & NS9750_MEM_DYN_TRRD_MA)
+
+	.word	NS9750_MEM_DYN_TMRD
+	.word	(0x1 & NS9750_MEM_DYN_TMRD_MA)
+
+	@@ CS 4
+	.word	NS9750_MEM_DYN_CFG(0)
+	.word	(NS9750_MEM_DYN_CFG_AM | \
+		 (0x280 & NS9750_MEM_DYN_CFG_AM_MA))
+
+	.word	NS9750_MEM_DYN_RAS_CAS(0)
+	.word	((0x200 & NS9750_MEM_DYN_RAS_CAS_CAS_MA) | \
+		 (0x03 & NS9750_MEM_DYN_RAS_CAS_RAS_MA))
+
+	@@ CS 5
+	.word	NS9750_MEM_DYN_CFG(1)
+	.word	(NS9750_MEM_DYN_CFG_AM | \
+		 (0x280 & NS9750_MEM_DYN_CFG_AM_MA))
+
+	.word	NS9750_MEM_DYN_RAS_CAS(1)
+	.word	((0x200 & NS9750_MEM_DYN_RAS_CAS_CAS_MA) | \
+		 (0x03 & NS9750_MEM_DYN_RAS_CAS_RAS_MA))
+
+	@@ CS 6
+	.word	NS9750_MEM_DYN_CFG(2)
+	.word	(NS9750_MEM_DYN_CFG_AM | \
+		 (0x280 & NS9750_MEM_DYN_CFG_AM_MA))
+
+	.word	NS9750_MEM_DYN_RAS_CAS(2)
+	.word	((0x200 & NS9750_MEM_DYN_RAS_CAS_CAS_MA) | \
+		 (0x03 & NS9750_MEM_DYN_RAS_CAS_RAS_MA))
+
+	@@ CS 7
+	.word	NS9750_MEM_DYN_CFG(3)
+	.word	(NS9750_MEM_DYN_CFG_AM | \
+		 (0x280 & NS9750_MEM_DYN_CFG_AM_MA))
+
+	.word	NS9750_MEM_DYN_RAS_CAS(3)
+	.word	((0x200 & NS9750_MEM_DYN_RAS_CAS_CAS_MA) | \
+		 (0x03 & NS9750_MEM_DYN_RAS_CAS_RAS_MA))
+
+	.word	NS9750_MEM_DYN_CTRL
+	.word	(NS9750_MEM_DYN_CTRL_I_PALL | \
+		 NS9750_MEM_DYN_CTRL_SR | \
+		 NS9750_MEM_DYN_CTRL_CE )
+
+	.word	NS9750_MEM_DYN_REFRESH
+	.word	(0x1 & NS9750_MEM_DYN_REFRESH_MA)
+	@@ No further register settings after refresh
+_MEM_CONFIG_END:
+
+_MEM_MODE_START:
+	.word	NS9750_MEM_DYN_REFRESH
+	.word	(0x30 & NS9750_MEM_DYN_REFRESH_MA)
+
+	.word	NS9750_MEM_DYN_CTRL
+	.word	(NS9750_MEM_DYN_CTRL_I_MODE | \
+		 NS9750_MEM_DYN_CTRL_SR | \
+		 NS9750_MEM_DYN_CTRL_CE )
+_MEM_MODE_END:
+
+_MEM_ENABLE_START:
+	.word	NS9750_MEM_DYN_CTRL
+	.word	(NS9750_MEM_DYN_CTRL_I_NORMAL | \
+		 NS9750_MEM_DYN_CTRL_SR | \
+		 NS9750_MEM_DYN_CTRL_CE )
+
+	@@ CS 4
+	.word	NS9750_MEM_DYN_CFG(0)
+	.word	(NS9750_MEM_DYN_CFG_BDMC | \
+		 NS9750_MEM_DYN_CFG_AM | \
+		 (0x280 & NS9750_MEM_DYN_CFG_AM_MA))
+
+	@@ CS 5
+	.word	NS9750_MEM_DYN_CFG(1)
+	.word	(NS9750_MEM_DYN_CFG_BDMC | \
+		 NS9750_MEM_DYN_CFG_AM | \
+		 (0x280 & NS9750_MEM_DYN_CFG_AM_MA))
+
+	@@ CS 6
+	.word	NS9750_MEM_DYN_CFG(2)
+	.word	(NS9750_MEM_DYN_CFG_BDMC | \
+		 NS9750_MEM_DYN_CFG_AM | \
+		 (0x280 & NS9750_MEM_DYN_CFG_AM_MA))
+
+	@@ CS 7
+	.word	NS9750_MEM_DYN_CFG(3)
+	.word	(NS9750_MEM_DYN_CFG_BDMC | \
+		 NS9750_MEM_DYN_CFG_AM | \
+		 (0x280 & NS9750_MEM_DYN_CFG_AM_MA))
+_MEM_ENABLE_END:
+
+_AHB_MONITOR_START:
+	.word	NS9750_SYS_AHB_TIMEOUT
+	.word	0x01000100	@ @TODO not calculated yet
+
+	.word	NS9750_SYS_AHB_MON
+	.word	(NS9750_SYS_AHB_MON_BMTC_GEN_IRQ | \
+		 NS9750_SYS_AHB_MON_BATC_GEN_IRQ)
+_AHB_MONITOR_END:
+
+#endif /* CONFIG_INIT_CRITICAL */
--- a/board/ns9750dev/u-boot.lds
+++ b/board/ns9750dev/u-boot.lds
@@ -0,0 +1,58 @@
+/*
+ * (C) Copyright 2002
+ * Gary Jennejohn, DENX Software Engineering, <gj@denx.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+/*OUTPUT_FORMAT("elf32-arm", "elf32-arm", "elf32-arm")*/
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+	. = 0x00000000;
+
+	. = ALIGN(4);
+	.text      :
+	{
+	  cpu/arm926ejs/start.o	(.text)
+	  *(.text)
+	}
+
+	. = ALIGN(4);
+	.rodata : { *(.rodata) }
+
+	. = ALIGN(4);
+	.data : { *(.data) }
+
+	. = ALIGN(4);
+	.got : { *(.got) }
+
+  __u_boot_cmd_start = .;
+  .u_boot_cmd : { *(.u_boot_cmd) }
+  __u_boot_cmd_end = .;
+
+
+	. = ALIGN(4);
+	__bss_start = .;
+	.bss : { *(.bss) }
+	_end = . ;
+
+}
--- a/board/ocotea/Makefile
+++ b/board/ocotea/Makefile
@@ -0,0 +1,47 @@
+#
+# (C) Copyright 2002
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	= $(BOARD).o flash.o
+SOBJS	= init.o
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) crv $@ $(OBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend *~
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+sinclude .depend
+
+#########################################################################
--- a/board/ocotea/config.mk
+++ b/board/ocotea/config.mk
@@ -0,0 +1,44 @@
+#
+# (C) Copyright 2004
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# IBM 440GX Reference Platform (Ocotea) board
+#
+
+#TEXT_BASE = 0xFFFE0000
+
+ifeq ($(ramsym),1)
+TEXT_BASE = 0x07FD0000
+else
+TEXT_BASE = 0xFFF80000
+endif
+
+PLATFORM_CPPFLAGS += -DCONFIG_440=1
+
+ifeq ($(debug),1)
+PLATFORM_CPPFLAGS += -DDEBUG
+endif
+
+ifeq ($(dbcr),1)
+PLATFORM_CPPFLAGS += -DCFG_INIT_DBCR=0x8cff0000
+endif
--- a/board/ocotea/flash.c
+++ b/board/ocotea/flash.c
@@ -0,0 +1,595 @@
+/*
+ * (C) Copyright 2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * (C) Copyright 2002 Jun Gu <jung@artesyncp.com>
+ * Add support for Am29F016D and dynamic switch setting.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * Modified 4/5/2001
+ * Wait for completion of each sector erase command issued
+ * 4/5/2001
+ * Chris Hallinan - DS4.COM, Inc. - clh@net1plus.com
+ */
+
+#include <common.h>
+#include <ppc4xx.h>
+#include <asm/processor.h>
+
+#undef DEBUG
+
+#ifdef DEBUG
+#define DEBUGF(x...) printf(x)
+#else
+#define DEBUGF(x...)
+#endif				/* DEBUG */
+
+#define     BOOT_SMALL_FLASH        32	/* 00100000 */
+#define     FLASH_ONBD_N            2	/* 00000010 */
+#define     FLASH_SRAM_SEL          1	/* 00000001 */
+
+#define     BOOT_SMALL_FLASH_VAL    4
+#define     FLASH_ONBD_N_VAL        2
+#define     FLASH_SRAM_SEL_VAL      1
+
+
+flash_info_t flash_info[CFG_MAX_FLASH_BANKS];	/* info for FLASH chips        */
+
+static unsigned long flash_addr_table[8][CFG_MAX_FLASH_BANKS] = {
+	{0xFF800000, 0xFF900000, 0xFFC00000},	/* 0:000: configuraton 4 */
+	{0xFF900000, 0xFF800000, 0xFFC00000},	/* 1:001: configuraton 3 */
+	{0x00000000, 0x00000000, 0x00000000},	/* 2:010: configuraton 8 */
+	{0x00000000, 0x00000000, 0x00000000},	/* 3:011: configuraton 7 */
+	{0xFFE00000, 0xFFF00000, 0xFF800000},	/* 4:100: configuraton 2 */
+	{0xFFF00000, 0xFFF80000, 0xFF800000},	/* 5:101: configuraton 1 */
+	{0x00000000, 0x00000000, 0x00000000},	/* 6:110: configuraton 6 */
+	{0x00000000, 0x00000000, 0x00000000}	/* 7:111: configuraton 5 */
+};
+
+/*-----------------------------------------------------------------------
+ * Functions
+ */
+static ulong flash_get_size(vu_long * addr, flash_info_t * info);
+static int write_word(flash_info_t * info, ulong dest, ulong data);
+
+
+#ifdef CONFIG_OCOTEA
+#define ADDR0           0x5555
+#define ADDR1           0x2aaa
+#define FLASH_WORD_SIZE unsigned char
+#endif
+
+/*-----------------------------------------------------------------------
+ */
+
+unsigned long flash_init(void)
+{
+	unsigned long total_b = 0;
+	unsigned long size_b[CFG_MAX_FLASH_BANKS];
+	unsigned char *fpga_base = (unsigned char *) CFG_FPGA_BASE;
+	unsigned char switch_status;
+	unsigned short index = 0;
+	int i;
+
+	/* read FPGA base register FPGA_REG0 */
+	switch_status = *fpga_base;
+
+	/* check the bitmap of switch status */
+	if (switch_status & BOOT_SMALL_FLASH) {
+		index += BOOT_SMALL_FLASH_VAL;
+	}
+	if (switch_status & FLASH_ONBD_N) {
+		index += FLASH_ONBD_N_VAL;
+	}
+	if (switch_status & FLASH_SRAM_SEL) {
+		index += FLASH_SRAM_SEL_VAL;
+	}
+
+	DEBUGF("\n");
+	DEBUGF("FLASH: Index: %d\n", index);
+
+	/* Init: no FLASHes known */
+	for (i = 0; i < CFG_MAX_FLASH_BANKS; ++i) {
+		flash_info[i].flash_id = FLASH_UNKNOWN;
+		flash_info[i].sector_count = -1;
+		flash_info[i].size = 0;
+
+		/* check whether the address is 0 */
+		if (flash_addr_table[index][i] == 0) {
+			continue;
+		}
+
+		/* call flash_get_size() to initialize sector address */
+		size_b[i] = flash_get_size((vu_long *) flash_addr_table[index][i], &flash_info[i]);
+		flash_info[i].size = size_b[i];
+		if (flash_info[i].flash_id == FLASH_UNKNOWN) {
+			printf ("## Unknown FLASH on Bank %d - Size = 0x%08lx = %ld MB\n",
+				i, size_b[i], size_b[i] << 20);
+			flash_info[i].sector_count = -1;
+			flash_info[i].size = 0;
+		}
+
+		total_b += flash_info[i].size;
+	}
+
+	return total_b;
+}
+
+/*-----------------------------------------------------------------------
+ */
+void flash_print_info(flash_info_t * info)
+{
+	int i;
+	int k;
+	int size;
+	int erased;
+	volatile unsigned long *flash;
+
+	if (info->flash_id == FLASH_UNKNOWN) {
+		printf("missing or unknown FLASH type\n");
+		return;
+	}
+
+	switch (info->flash_id & FLASH_VENDMASK) {
+	case FLASH_MAN_AMD:
+		printf("AMD ");
+		break;
+	case FLASH_MAN_FUJ:
+		printf("FUJITSU ");
+		break;
+	case FLASH_MAN_SST:
+		printf("SST ");
+		break;
+	default:
+		printf("Unknown Vendor ");
+		break;
+	}
+
+	switch (info->flash_id & FLASH_TYPEMASK) {
+	case FLASH_AM040:
+		printf("AM29F040 (512 Kbit, uniform sector size)\n");
+		break;
+	case FLASH_AM400B:
+		printf("AM29LV400B (4 Mbit, bottom boot sect)\n");
+		break;
+	case FLASH_AM400T:
+		printf("AM29LV400T (4 Mbit, top boot sector)\n");
+		break;
+	case FLASH_AM800B:
+		printf("AM29LV800B (8 Mbit, bottom boot sect)\n");
+		break;
+	case FLASH_AM800T:
+		printf("AM29LV800T (8 Mbit, top boot sector)\n");
+		break;
+	case FLASH_AM160B:
+		printf("AM29LV160B (16 Mbit, bottom boot sect)\n");
+		break;
+	case FLASH_AM160T:
+		printf("AM29LV160T (16 Mbit, top boot sector)\n");
+		break;
+	case FLASH_AM320B:
+		printf("AM29LV320B (32 Mbit, bottom boot sect)\n");
+		break;
+	case FLASH_AM320T:
+		printf("AM29LV320T (32 Mbit, top boot sector)\n");
+		break;
+	case FLASH_AMDLV033C:
+		printf("AM29LV033C (32 Mbit, top boot sector)\n");
+		break;
+	case FLASH_SST800A:
+		printf("SST39LF/VF800 (8 Mbit, uniform sector size)\n");
+		break;
+	case FLASH_SST160A:
+		printf("SST39LF/VF160 (16 Mbit, uniform sector size)\n");
+		break;
+	default:
+		printf("Unknown Chip Type\n");
+		break;
+	}
+
+	printf("  Size: %ld KB in %d Sectors\n",
+	       info->size >> 10, info->sector_count);
+
+	printf("  Sector Start Addresses:");
+	for (i = 0; i < info->sector_count; ++i) {
+		/*
+		 * Check if whole sector is erased
+		 */
+		if (i != (info->sector_count - 1))
+			size = info->start[i + 1] - info->start[i];
+		else
+			size = info->start[0] + info->size - info->start[i];
+		erased = 1;
+		flash = (volatile unsigned long *) info->start[i];
+		size = size >> 2;	/* divide by 4 for longword access */
+		for (k = 0; k < size; k++) {
+			if (*flash++ != 0xffffffff) {
+				erased = 0;
+				break;
+			}
+		}
+
+		if ((i % 5) == 0)
+			printf("\n   ");
+		printf(" %08lX%s%s",
+		       info->start[i],
+		       erased ? " E" : "  ", info->protect[i] ? "RO " : "   ");
+	}
+	printf("\n");
+	return;
+}
+
+/*-----------------------------------------------------------------------
+ */
+
+/*
+ * The following code cannot be run from FLASH!
+ */
+static ulong flash_get_size(vu_long * addr, flash_info_t * info)
+{
+	short i;
+	FLASH_WORD_SIZE value;
+	ulong base = (ulong) addr;
+	volatile FLASH_WORD_SIZE *addr2 = (FLASH_WORD_SIZE *) addr;
+
+	DEBUGF("FLASH ADDR: %08x\n", (unsigned) addr);
+
+	/* Write auto select command: read Manufacturer ID */
+	udelay(10000);
+	addr2[ADDR0] = (FLASH_WORD_SIZE) 0x00AA00AA;
+	udelay(1000);
+	addr2[ADDR1] = (FLASH_WORD_SIZE) 0x00550055;
+	udelay(1000);
+	addr2[ADDR0] = (FLASH_WORD_SIZE) 0x00900090;
+	udelay(1000);
+
+	value = addr2[0];
+	DEBUGF("FLASH MANUFACT: %x\n", value);
+
+	switch (value) {
+	case (FLASH_WORD_SIZE) AMD_MANUFACT:
+		info->flash_id = FLASH_MAN_AMD;
+		break;
+	case (FLASH_WORD_SIZE) FUJ_MANUFACT:
+		info->flash_id = FLASH_MAN_FUJ;
+		break;
+	case (FLASH_WORD_SIZE) SST_MANUFACT:
+		info->flash_id = FLASH_MAN_SST;
+		break;
+	case (FLASH_WORD_SIZE) STM_MANUFACT:
+		info->flash_id = FLASH_MAN_STM;
+		break;
+	default:
+		info->flash_id = FLASH_UNKNOWN;
+		info->sector_count = 0;
+		info->size = 0;
+		return (0);		/* no or unknown flash  */
+	}
+
+	value = addr2[1];		/* device ID            */
+
+	DEBUGF("\nFLASH DEVICEID: %x\n", value);
+
+	switch (value) {
+	case (FLASH_WORD_SIZE) AMD_ID_LV040B:
+		info->flash_id += FLASH_AM040;
+		info->sector_count = 8;
+		info->size = 0x0080000;	/* => 512 ko */
+		break;
+	case (FLASH_WORD_SIZE) AMD_ID_F040B:
+		info->flash_id += FLASH_AM040;
+		info->sector_count = 8;
+		info->size = 0x0080000;	/* => 512 ko */
+		break;
+	case (FLASH_WORD_SIZE) AMD_ID_LV033C:
+		info->flash_id += FLASH_AMDLV033C;
+		info->sector_count = 64;
+		info->size = 0x00400000;
+		break;			/* => 4 MB              */
+	default:
+		info->flash_id = FLASH_UNKNOWN;
+		return (0);		/* => no or unknown flash */
+	}
+
+	/* set up sector start address table */
+	if (((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_SST) ||
+	    (info->flash_id == FLASH_AM040) ||
+	    (info->flash_id == FLASH_AMD016)) {
+		for (i = 0; i < info->sector_count; i++)
+			info->start[i] = base + (i * 0x00010000);
+	} else {
+		if (info->flash_id & FLASH_BTYPE) {
+			/* set sector offsets for bottom boot block type        */
+			info->start[0] = base + 0x00000000;
+			info->start[1] = base + 0x00004000;
+			info->start[2] = base + 0x00006000;
+			info->start[3] = base + 0x00008000;
+			for (i = 4; i < info->sector_count; i++) {
+				info->start[i] = base + (i * 0x00010000) - 0x00030000;
+			}
+		} else {
+			/* set sector offsets for top boot block type           */
+			i = info->sector_count - 1;
+			info->start[i--] = base + info->size - 0x00004000;
+			info->start[i--] = base + info->size - 0x00006000;
+			info->start[i--] = base + info->size - 0x00008000;
+			for (; i >= 0; i--) {
+				info->start[i] = base + i * 0x00010000;
+			}
+		}
+	}
+
+	/* check for protected sectors */
+	for (i = 0; i < info->sector_count; i++) {
+		/* read sector protection at sector address, (A7 .. A0) = 0x02 */
+		/* D0 = 1 if protected */
+		addr2 = (volatile FLASH_WORD_SIZE *) (info->start[i]);
+		if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_SST)
+			info->protect[i] = 0;
+		else
+			info->protect[i] = addr2[2] & 1;
+	}
+
+	/*
+	 * Prevent writes to uninitialized FLASH.
+	 */
+	if (info->flash_id != FLASH_UNKNOWN) {
+	}
+
+	return (info->size);
+}
+
+int wait_for_DQ7(flash_info_t * info, int sect)
+{
+	ulong start, now, last;
+	volatile FLASH_WORD_SIZE *addr =
+		(FLASH_WORD_SIZE *) (info->start[sect]);
+
+	start = get_timer(0);
+	last = start;
+	while ((addr[0] & (FLASH_WORD_SIZE) 0x00800080) !=
+	       (FLASH_WORD_SIZE) 0x00800080) {
+		if ((now = get_timer(start)) > CFG_FLASH_ERASE_TOUT) {
+			printf("Timeout\n");
+			return -1;
+		}
+		/* show that we're waiting */
+		if ((now - last) > 1000) {	/* every second */
+			putc('.');
+			last = now;
+		}
+	}
+	return 0;
+}
+
+/*-----------------------------------------------------------------------
+ */
+
+int flash_erase(flash_info_t * info, int s_first, int s_last)
+{
+	volatile FLASH_WORD_SIZE *addr = (FLASH_WORD_SIZE *) (info->start[0]);
+	volatile FLASH_WORD_SIZE *addr2;
+	int flag, prot, sect, l_sect;
+	int i;
+
+	if ((s_first < 0) || (s_first > s_last)) {
+		if (info->flash_id == FLASH_UNKNOWN) {
+			printf("- missing\n");
+		} else {
+			printf("- no sectors to erase\n");
+		}
+		return 1;
+	}
+
+	if (info->flash_id == FLASH_UNKNOWN) {
+		printf("Can't erase unknown flash type - aborted\n");
+		return 1;
+	}
+
+	prot = 0;
+	for (sect = s_first; sect <= s_last; ++sect) {
+		if (info->protect[sect]) {
+			prot++;
+		}
+	}
+
+	if (prot) {
+		printf("- Warning: %d protected sectors will not be erased!\n",
+		       prot);
+	} else {
+		printf("\n");
+	}
+
+	l_sect = -1;
+
+	/* Disable interrupts which might cause a timeout here */
+	flag = disable_interrupts();
+
+	/* Start erase on unprotected sectors */
+	for (sect = s_first; sect <= s_last; sect++) {
+		if (info->protect[sect] == 0) {	/* not protected */
+			addr2 = (FLASH_WORD_SIZE *) (info->start[sect]);
+			printf("Erasing sector %p\n", addr2);
+
+			if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_SST) {
+				addr[ADDR0] = (FLASH_WORD_SIZE) 0x00AA00AA;
+				addr[ADDR1] = (FLASH_WORD_SIZE) 0x00550055;
+				addr[ADDR0] = (FLASH_WORD_SIZE) 0x00800080;
+				addr[ADDR0] = (FLASH_WORD_SIZE) 0x00AA00AA;
+				addr[ADDR1] = (FLASH_WORD_SIZE) 0x00550055;
+				addr2[0] = (FLASH_WORD_SIZE) 0x00500050;	/* block erase */
+				for (i = 0; i < 50; i++)
+					udelay(1000);	/* wait 1 ms */
+			} else {
+				addr[ADDR0] = (FLASH_WORD_SIZE) 0x00AA00AA;
+				addr[ADDR1] = (FLASH_WORD_SIZE) 0x00550055;
+				addr[ADDR0] = (FLASH_WORD_SIZE) 0x00800080;
+				addr[ADDR0] = (FLASH_WORD_SIZE) 0x00AA00AA;
+				addr[ADDR1] = (FLASH_WORD_SIZE) 0x00550055;
+				addr2[0] = (FLASH_WORD_SIZE) 0x00300030;	/* sector erase */
+			}
+			l_sect = sect;
+			/*
+			 * Wait for each sector to complete, it's more
+			 * reliable.  According to AMD Spec, you must
+			 * issue all erase commands within a specified
+			 * timeout.  This has been seen to fail, especially
+			 * if printf()s are included (for debug)!!
+			 */
+			wait_for_DQ7(info, sect);
+		}
+	}
+
+	/* re-enable interrupts if necessary */
+	if (flag)
+		enable_interrupts();
+
+	/* wait at least 80us - let's wait 1 ms */
+	udelay(1000);
+
+	/* reset to read mode */
+	addr = (FLASH_WORD_SIZE *) info->start[0];
+	addr[0] = (FLASH_WORD_SIZE) 0x00F000F0;	/* reset bank */
+
+	printf(" done\n");
+	return 0;
+}
+
+/*-----------------------------------------------------------------------
+ * Copy memory to flash, returns:
+ * 0 - OK
+ * 1 - write timeout
+ * 2 - Flash not erased
+ */
+int write_buff(flash_info_t * info, uchar * src, ulong addr, ulong cnt)
+{
+	ulong cp, wp, data;
+	int i, l, rc;
+
+	wp = (addr & ~3);		/* get lower word aligned address */
+
+	/*
+	 * handle unaligned start bytes
+	 */
+	if ((l = addr - wp) != 0) {
+		data = 0;
+	    for (i = 0, cp = wp; i < l; ++i, ++cp) {
+		    data = (data << 8) | (*(uchar *) cp);
+	    }
+	    for (; i < 4 && cnt > 0; ++i) {
+		    data = (data << 8) | *src++;
+		    --cnt;
+		    ++cp;
+	    }
+	    for (; cnt == 0 && i < 4; ++i, ++cp) {
+		    data = (data << 8) | (*(uchar *) cp);
+	    }
+
+	    if ((rc = write_word(info, wp, data)) != 0) {
+		    return (rc);
+	    }
+	    wp += 4;
+	}
+
+	/*
+	 * handle word aligned part
+	 */
+	while (cnt >= 4) {
+		data = 0;
+		for (i = 0; i < 4; ++i) {
+			data = (data << 8) | *src++;
+		}
+		if ((rc = write_word(info, wp, data)) != 0) {
+			return (rc);
+		}
+		wp += 4;
+		cnt -= 4;
+	}
+
+	if (cnt == 0) {
+		return (0);
+	}
+
+	/*
+	 * handle unaligned tail bytes
+	 */
+	data = 0;
+	for (i = 0, cp = wp; i < 4 && cnt > 0; ++i, ++cp) {
+		data = (data << 8) | *src++;
+		--cnt;
+	}
+	for (; i < 4; ++i, ++cp) {
+		data = (data << 8) | (*(uchar *) cp);
+	}
+
+	return (write_word(info, wp, data));
+}
+
+/*-----------------------------------------------------------------------
+ * Write a word to Flash, returns:
+ * 0 - OK
+ * 1 - write timeout
+ * 2 - Flash not erased
+ */
+static int write_word(flash_info_t * info, ulong dest, ulong data)
+{
+	volatile FLASH_WORD_SIZE *addr2 = (FLASH_WORD_SIZE *) (info->start[0]);
+	volatile FLASH_WORD_SIZE *dest2 = (FLASH_WORD_SIZE *) dest;
+	volatile FLASH_WORD_SIZE *data2 = (FLASH_WORD_SIZE *) & data;
+	ulong start;
+	int i;
+
+	/* Check if Flash is (sufficiently) erased */
+	if ((*((volatile FLASH_WORD_SIZE *) dest) &
+	     (FLASH_WORD_SIZE) data) != (FLASH_WORD_SIZE) data) {
+		return (2);
+	}
+
+	for (i = 0; i < 4 / sizeof(FLASH_WORD_SIZE); i++) {
+		int flag;
+
+		/* Disable interrupts which might cause a timeout here */
+		flag = disable_interrupts();
+
+		addr2[ADDR0] = (FLASH_WORD_SIZE) 0x00AA00AA;
+		addr2[ADDR1] = (FLASH_WORD_SIZE) 0x00550055;
+		addr2[ADDR0] = (FLASH_WORD_SIZE) 0x00A000A0;
+
+		dest2[i] = data2[i];
+
+		/* re-enable interrupts if necessary */
+		if (flag)
+			enable_interrupts();
+
+		/* data polling for D7 */
+		start = get_timer(0);
+		while ((dest2[i] & (FLASH_WORD_SIZE) 0x00800080) !=
+		       (data2[i] & (FLASH_WORD_SIZE) 0x00800080)) {
+
+			if (get_timer(start) > CFG_FLASH_WRITE_TOUT) {
+				return (1);
+			}
+		}
+	}
+
+	return (0);
+}
--- a/board/ocotea/init.S
+++ b/board/ocotea/init.S
@@ -0,0 +1,96 @@
+/*
+*  Copyright (C) 2002 Scott McNutt <smcnutt@artesyncp.com>
+*
+* See file CREDITS for list of people who contributed to this
+* project.
+*
+* This program is free software; you can redistribute it and/or
+* modify it under the terms of the GNU General Public License as
+* published by the Free Software Foundation; either version 2 of
+* the License, or (at your option) any later version.
+*
+* This program is distributed in the hope that it will be useful,
+* but WITHOUT ANY WARRANTY; without even the implied warranty of
+* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+* GNU General Public License for more details.
+*
+* You should have received a copy of the GNU General Public License
+* along with this program; if not, write to the Free Software
+* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+* MA 02111-1307 USA
+*/
+
+#include <ppc_asm.tmpl>
+#include <config.h>
+
+/* General */
+#define TLB_VALID   0x00000200
+
+/* Supported page sizes */
+
+#define SZ_1K	    0x00000000
+#define SZ_4K	    0x00000010
+#define SZ_16K	    0x00000020
+#define SZ_64K	    0x00000030
+#define SZ_256K    0x00000040
+#define SZ_1M	    0x00000050
+#define SZ_16M	    0x00000070
+#define SZ_256M    0x00000090
+
+/* Storage attributes */
+#define SA_W	    0x00000800	    /* Write-through */
+#define SA_I	    0x00000400	    /* Caching inhibited */
+#define SA_M	    0x00000200	    /* Memory coherence */
+#define SA_G	    0x00000100	    /* Guarded */
+#define SA_E	    0x00000080	    /* Endian */
+
+/* Access control */
+#define AC_X	    0x00000024	    /* Execute */
+#define AC_W	    0x00000012	    /* Write */
+#define AC_R	    0x00000009	    /* Read */
+
+/* Some handy macros */
+
+#define EPN(e)		((e) & 0xfffffc00)
+#define TLB0(epn,sz)	( (EPN((epn)) | (sz) | TLB_VALID ) )
+#define TLB1(rpn,erpn)	( ((rpn)&0xfffffc00) | (erpn) )
+#define TLB2(a)	( (a)&0x00000fbf )
+
+#define tlbtab_start\
+	mflr    r1  ;\
+	bl 0f	    ;
+
+#define tlbtab_end\
+	.long 0, 0, 0	;   \
+0:	mflr    r0	;   \
+	mtlr    r1	;   \
+	blr		;
+
+#define tlbentry(epn,sz,rpn,erpn,attr)\
+	.long TLB0(epn,sz),TLB1(rpn,erpn),TLB2(attr)
+
+
+/**************************************************************************
+ * TLB TABLE
+ *
+ * This table is used by the cpu boot code to setup the initial tlb
+ * entries. Rather than make broad assumptions in the cpu source tree,
+ * this table lets each board set things up however they like.
+ *
+ *  Pointer to the table is returned in r1
+ *
+ *************************************************************************/
+
+    .section .bootpg,"ax"
+    .globl tlbtab
+
+tlbtab:
+    tlbtab_start
+    tlbentry( 0xf0000000, SZ_256M, 0xf0000000, 1, AC_R|AC_W|AC_X|SA_G|SA_I)
+    tlbentry( CFG_PERIPHERAL_BASE, SZ_256M, 0x40000000, 1, AC_R|AC_W|SA_G|SA_I)
+    tlbentry( CFG_ISRAM_BASE, SZ_4K, 0x80000000, 0, AC_R|AC_W|AC_X )
+    tlbentry( CFG_ISRAM_BASE + 0x1000, SZ_4K, 0x80001000, 0, AC_R|AC_W|AC_X )
+    tlbentry( CFG_SDRAM_BASE, SZ_256M, 0x00000000, 0, AC_R|AC_W|AC_X|SA_G|SA_I )
+    tlbentry( CFG_PCI_BASE, SZ_256M, 0x00000000, 2, AC_R|AC_W|SA_G|SA_I )
+    tlbentry( CFG_PCI_MEMBASE, SZ_256M, 0x00000000, 3, AC_R|AC_W|SA_G|SA_I )
+    tlbtab_end
--- a/board/ocotea/ocotea.c
+++ b/board/ocotea/ocotea.c
@@ -0,0 +1,476 @@
+/*
+ *  Copyright (C) 2004 PaulReynolds@lhsolutions.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+
+#include <common.h>
+#include "ocotea.h"
+#include <asm/processor.h>
+#include <spd_sdram.h>
+#include <440gx_enet.h>
+
+#define BOOT_SMALL_FLASH	32	/* 00100000 */
+#define FLASH_ONBD_N		2	/* 00000010 */
+#define FLASH_SRAM_SEL		1	/* 00000001 */
+
+long int fixed_sdram (void);
+void fpga_init (void);
+
+int board_early_init_f (void)
+{
+	unsigned long mfr;
+	/*-------------------------------------------------------------------------+
+	  | Initialize EBC CONFIG
+	  +-------------------------------------------------------------------------*/
+	mtebc(xbcfg, EBC_CFG_LE_UNLOCK |
+	      EBC_CFG_PTD_ENABLE | EBC_CFG_RTC_64PERCLK |
+	      EBC_CFG_ATC_PREVIOUS | EBC_CFG_DTC_PREVIOUS |
+	      EBC_CFG_CTC_PREVIOUS | EBC_CFG_EMC_NONDEFAULT |
+	      EBC_CFG_PME_DISABLE | EBC_CFG_PR_32);
+
+	/*-------------------------------------------------------------------------+
+	  | 1 MB FLASH / 1 MB SRAM. Initialize bank 0 with default values.
+	  +-------------------------------------------------------------------------*/
+	mtebc(pb0ap, EBC_BXAP_BME_DISABLED|EBC_BXAP_TWT_ENCODE(8)|
+	      EBC_BXAP_BCE_DISABLE|
+	      EBC_BXAP_CSN_ENCODE(1)|EBC_BXAP_OEN_ENCODE(1)|
+	      EBC_BXAP_WBN_ENCODE(1)|EBC_BXAP_WBF_ENCODE(1)|
+	      EBC_BXAP_TH_ENCODE(1)|EBC_BXAP_RE_DISABLED|
+	      EBC_BXAP_BEM_WRITEONLY|
+	      EBC_BXAP_PEN_DISABLED);
+	mtebc(pb0cr, EBC_BXCR_BAS_ENCODE(0xFFE00000)|
+	      EBC_BXCR_BS_2MB|EBC_BXCR_BU_RW|EBC_BXCR_BW_8BIT);
+
+	/*-------------------------------------------------------------------------+
+	  | 8KB NVRAM/RTC. Initialize bank 1 with default values.
+	  +-------------------------------------------------------------------------*/
+	mtebc(pb1ap, EBC_BXAP_BME_DISABLED|EBC_BXAP_TWT_ENCODE(10)|
+	      EBC_BXAP_BCE_DISABLE|
+	      EBC_BXAP_CSN_ENCODE(1)|EBC_BXAP_OEN_ENCODE(1)|
+	      EBC_BXAP_WBN_ENCODE(1)|EBC_BXAP_WBF_ENCODE(1)|
+	      EBC_BXAP_TH_ENCODE(1)|EBC_BXAP_RE_DISABLED|
+	      EBC_BXAP_BEM_WRITEONLY|
+	      EBC_BXAP_PEN_DISABLED);
+	mtebc(pb1cr, EBC_BXCR_BAS_ENCODE(0x48000000)|
+	      EBC_BXCR_BS_1MB|EBC_BXCR_BU_RW|EBC_BXCR_BW_8BIT);
+
+	/*-------------------------------------------------------------------------+
+	  | 4 MB FLASH. Initialize bank 2 with default values.
+	  +-------------------------------------------------------------------------*/
+	mtebc(pb2ap, EBC_BXAP_BME_DISABLED|EBC_BXAP_TWT_ENCODE(10)|
+	      EBC_BXAP_BCE_DISABLE|
+	      EBC_BXAP_CSN_ENCODE(1)|EBC_BXAP_OEN_ENCODE(1)|
+	      EBC_BXAP_WBN_ENCODE(1)|EBC_BXAP_WBF_ENCODE(1)|
+	      EBC_BXAP_TH_ENCODE(1)|EBC_BXAP_RE_DISABLED|
+	      EBC_BXAP_BEM_WRITEONLY|
+	      EBC_BXAP_PEN_DISABLED);
+	mtebc(pb2cr, EBC_BXCR_BAS_ENCODE(0xFF800000)|
+	      EBC_BXCR_BS_4MB|EBC_BXCR_BU_RW|EBC_BXCR_BW_8BIT);
+
+	/*-------------------------------------------------------------------------+
+	  | FPGA. Initialize bank 7 with default values.
+	  +-------------------------------------------------------------------------*/
+	mtebc(pb7ap, EBC_BXAP_BME_DISABLED|EBC_BXAP_TWT_ENCODE(7)|
+	      EBC_BXAP_BCE_DISABLE|
+	      EBC_BXAP_CSN_ENCODE(1)|EBC_BXAP_OEN_ENCODE(1)|
+	      EBC_BXAP_WBN_ENCODE(1)|EBC_BXAP_WBF_ENCODE(1)|
+	      EBC_BXAP_TH_ENCODE(1)|EBC_BXAP_RE_DISABLED|
+	      EBC_BXAP_BEM_WRITEONLY|
+	      EBC_BXAP_PEN_DISABLED);
+	mtebc(pb7cr, EBC_BXCR_BAS_ENCODE(0x48300000)|
+	      EBC_BXCR_BS_1MB|EBC_BXCR_BU_RW|EBC_BXCR_BW_8BIT);
+
+	/*--------------------------------------------------------------------
+	 * Setup the interrupt controller polarities, triggers, etc.
+	 *-------------------------------------------------------------------*/
+	mtdcr (uic0sr, 0xffffffff);	/* clear all */
+	mtdcr (uic0er, 0x00000000);	/* disable all */
+	mtdcr (uic0cr, 0x00000009);	/* SMI & UIC1 crit are critical */
+	mtdcr (uic0pr, 0xfffffe13);	/* per ref-board manual */
+	mtdcr (uic0tr, 0x01c00008);	/* per ref-board manual */
+	mtdcr (uic0vr, 0x00000001);	/* int31 highest, base=0x000 */
+	mtdcr (uic0sr, 0xffffffff);	/* clear all */
+
+	mtdcr (uic1sr, 0xffffffff);	/* clear all */
+	mtdcr (uic1er, 0x00000000);	/* disable all */
+	mtdcr (uic1cr, 0x00000000);	/* all non-critical */
+	mtdcr (uic1pr, 0xffffe0ff);	/* per ref-board manual */
+	mtdcr (uic1tr, 0x00ffc000);	/* per ref-board manual */
+	mtdcr (uic1vr, 0x00000001);	/* int31 highest, base=0x000 */
+	mtdcr (uic1sr, 0xffffffff);	/* clear all */
+
+	mtdcr (uic2sr, 0xffffffff);	/* clear all */
+	mtdcr (uic2er, 0x00000000);	/* disable all */
+	mtdcr (uic2cr, 0x00000000);	/* all non-critical */
+	mtdcr (uic2pr, 0xffffffff);	/* per ref-board manual */
+	mtdcr (uic2tr, 0x00ff8c0f);	/* per ref-board manual */
+	mtdcr (uic2vr, 0x00000001);	/* int31 highest, base=0x000 */
+	mtdcr (uic2sr, 0xffffffff);	/* clear all */
+
+	mtdcr (uicb0sr, 0xfc000000); /* clear all */
+	mtdcr (uicb0er, 0x00000000); /* disable all */
+	mtdcr (uicb0cr, 0x00000000); /* all non-critical */
+	mtdcr (uicb0pr, 0xfc000000); /* */
+	mtdcr (uicb0tr, 0x00000000); /* */
+	mtdcr (uicb0vr, 0x00000001); /* */
+	mfsdr (sdr_mfr, mfr);
+	mfr &= ~SDR0_MFR_ECS_MASK;
+/*	mtsdr(sdr_mfr, mfr); */
+	fpga_init();
+
+	return 0;
+}
+
+
+int checkboard (void)
+{
+	sys_info_t sysinfo;
+
+	get_sys_info (&sysinfo);
+
+	printf ("Board: IBM 440GX Evaluation Board\n");
+	printf ("\tVCO: %lu MHz\n", sysinfo.freqVCOMhz / 1000000);
+	printf ("\tCPU: %lu MHz\n", sysinfo.freqProcessor / 1000000);
+	printf ("\tPLB: %lu MHz\n", sysinfo.freqPLB / 1000000);
+	printf ("\tOPB: %lu MHz\n", sysinfo.freqOPB / 1000000);
+	printf ("\tEPB: %lu MHz\n", sysinfo.freqEPB / 1000000);
+	return (0);
+}
+
+
+long int initdram (int board_type)
+{
+	long dram_size = 0;
+
+#if defined(CONFIG_SPD_EEPROM)
+	dram_size = spd_sdram (0);
+#else
+	dram_size = fixed_sdram ();
+#endif
+	return dram_size;
+}
+
+
+#if defined(CFG_DRAM_TEST)
+int testdram (void)
+{
+	uint *pstart = (uint *) 0x00000000;
+	uint *pend = (uint *) 0x08000000;
+	uint *p;
+
+	for (p = pstart; p < pend; p++)
+		*p = 0xaaaaaaaa;
+
+	for (p = pstart; p < pend; p++) {
+		if (*p != 0xaaaaaaaa) {
+			printf ("SDRAM test fails at: %08x\n", (uint) p);
+			return 1;
+		}
+	}
+
+	for (p = pstart; p < pend; p++)
+		*p = 0x55555555;
+
+	for (p = pstart; p < pend; p++) {
+		if (*p != 0x55555555) {
+			printf ("SDRAM test fails at: %08x\n", (uint) p);
+			return 1;
+		}
+	}
+	return 0;
+}
+#endif
+
+#if !defined(CONFIG_SPD_EEPROM)
+/*************************************************************************
+ *  fixed sdram init -- doesn't use serial presence detect.
+ *
+ *  Assumes:    128 MB, non-ECC, non-registered
+ *              PLB @ 133 MHz
+ *
+ ************************************************************************/
+long int fixed_sdram (void)
+{
+	uint reg;
+
+	/*--------------------------------------------------------------------
+	 * Setup some default
+	 *------------------------------------------------------------------*/
+	mtsdram (mem_uabba, 0x00000000);	/* ubba=0 (default)             */
+	mtsdram (mem_slio, 0x00000000);		/* rdre=0 wrre=0 rarw=0         */
+	mtsdram (mem_devopt, 0x00000000);	/* dll=0 ds=0 (normal)          */
+	mtsdram (mem_wddctr, 0x00000000);	/* wrcp=0 dcd=0                 */
+	mtsdram (mem_clktr, 0x40000000);	/* clkp=1 (90 deg wr) dcdt=0    */
+
+	/*--------------------------------------------------------------------
+	 * Setup for board-specific specific mem
+	 *------------------------------------------------------------------*/
+	/*
+	 * Following for CAS Latency = 2.5 @ 133 MHz PLB
+	 */
+	mtsdram (mem_b0cr, 0x000a4001);	/* SDBA=0x000 128MB, Mode 3, enabled */
+	mtsdram (mem_tr0, 0x410a4012);	/* WR=2  WD=1 CL=2.5 PA=3 CP=4 LD=2 */
+	/* RA=10 RD=3                       */
+	mtsdram (mem_tr1, 0x8080082f);	/* SS=T2 SL=STAGE 3 CD=1 CT=0x02f   */
+	mtsdram (mem_rtr, 0x08200000);	/* Rate 15.625 ns @ 133 MHz PLB     */
+	mtsdram (mem_cfg1, 0x00000000);	/* Self-refresh exit, disable PM    */
+	udelay (400);			/* Delay 200 usecs (min)            */
+
+	/*--------------------------------------------------------------------
+	 * Enable the controller, then wait for DCEN to complete
+	 *------------------------------------------------------------------*/
+	mtsdram (mem_cfg0, 0x86000000);	/* DCEN=1, PMUD=1, 64-bit           */
+	for (;;) {
+		mfsdram (mem_mcsts, reg);
+		if (reg & 0x80000000)
+			break;
+	}
+
+	return (128 * 1024 * 1024);	/* 128 MB                           */
+}
+#endif	/* !defined(CONFIG_SPD_EEPROM) */
+
+
+/*************************************************************************
+ *  pci_pre_init
+ *
+ *  This routine is called just prior to registering the hose and gives
+ *  the board the opportunity to check things. Returning a value of zero
+ *  indicates that things are bad & PCI initialization should be aborted.
+ *
+ *	Different boards may wish to customize the pci controller structure
+ *	(add regions, override default access routines, etc) or perform
+ *	certain pre-initialization actions.
+ *
+ ************************************************************************/
+#if defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT)
+int pci_pre_init(struct pci_controller * hose )
+{
+	unsigned long strap;
+
+	/*--------------------------------------------------------------------------+
+	 *	The ocotea board is always configured as the host & requires the
+	 *	PCI arbiter to be enabled.
+	 *--------------------------------------------------------------------------*/
+	mfsdr(sdr_sdstp1, strap);
+	if( (strap & SDR0_SDSTP1_PAE_MASK) == 0 ){
+		printf("PCI: SDR0_STRP1[%08lX] - PCI Arbiter disabled.\n",strap);
+		return 0;
+	}
+
+	return 1;
+}
+#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT) */
+
+/*************************************************************************
+ *  pci_target_init
+ *
+ *	The bootstrap configuration provides default settings for the pci
+ *	inbound map (PIM). But the bootstrap config choices are limited and
+ *	may not be sufficient for a given board.
+ *
+ ************************************************************************/
+#if defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT)
+void pci_target_init(struct pci_controller * hose )
+{
+	DECLARE_GLOBAL_DATA_PTR;
+
+	/*--------------------------------------------------------------------------+
+	 * Disable everything
+	 *--------------------------------------------------------------------------*/
+	out32r( PCIX0_PIM0SA, 0 ); /* disable */
+	out32r( PCIX0_PIM1SA, 0 ); /* disable */
+	out32r( PCIX0_PIM2SA, 0 ); /* disable */
+	out32r( PCIX0_EROMBA, 0 ); /* disable expansion rom */
+
+	/*--------------------------------------------------------------------------+
+	 * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 strapping
+	 * options to not support sizes such as 128/256 MB.
+	 *--------------------------------------------------------------------------*/
+	out32r( PCIX0_PIM0LAL, CFG_SDRAM_BASE );
+	out32r( PCIX0_PIM0LAH, 0 );
+	out32r( PCIX0_PIM0SA, ~(gd->ram_size - 1) | 1 );
+
+	out32r( PCIX0_BAR0, 0 );
+
+	/*--------------------------------------------------------------------------+
+	 * Program the board's subsystem id/vendor id
+	 *--------------------------------------------------------------------------*/
+	out16r( PCIX0_SBSYSVID, CFG_PCI_SUBSYS_VENDORID );
+	out16r( PCIX0_SBSYSID, CFG_PCI_SUBSYS_DEVICEID );
+
+	out16r( PCIX0_CMD, in16r(PCIX0_CMD) | PCI_COMMAND_MEMORY );
+}
+#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT) */
+
+
+/*************************************************************************
+ *  is_pci_host
+ *
+ *	This routine is called to determine if a pci scan should be
+ *	performed. With various hardware environments (especially cPCI and
+ *	PPMC) it's insufficient to depend on the state of the arbiter enable
+ *	bit in the strap register, or generic host/adapter assumptions.
+ *
+ *	Rather than hard-code a bad assumption in the general 440 code, the
+ *	440 pci code requires the board to decide at runtime.
+ *
+ *	Return 0 for adapter mode, non-zero for host (monarch) mode.
+ *
+ *
+ ************************************************************************/
+#if defined(CONFIG_PCI)
+int is_pci_host(struct pci_controller *hose)
+{
+    /* The ocotea board is always configured as host. */
+    return(1);
+}
+#endif /* defined(CONFIG_PCI) */
+
+
+void fpga_init(void)
+{
+	unsigned long group;
+	unsigned long sdr0_pfc0;
+	unsigned long sdr0_pfc1;
+	unsigned long sdr0_cust0;
+	unsigned long pvr;
+
+	mfsdr (sdr_pfc0, sdr0_pfc0);
+	mfsdr (sdr_pfc1, sdr0_pfc1);
+	group = SDR0_PFC1_EPS_DECODE(sdr0_pfc1);
+	pvr = get_pvr ();
+
+	sdr0_pfc0 = (sdr0_pfc0 & ~SDR0_PFC0_GEIE_MASK) | SDR0_PFC0_GEIE_TRE;
+	if ( ((pvr == PVR_440GX_RA) || (pvr == PVR_440GX_RB)) && ((group == 4) || (group == 5))) {
+		sdr0_pfc0 = (sdr0_pfc0 & ~SDR0_PFC0_TRE_MASK) | SDR0_PFC0_TRE_DISABLE;
+		sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_CTEMS_MASK) | SDR0_PFC1_CTEMS_EMS;
+		out8(FPGA_REG2, (in8(FPGA_REG2) & ~FPGA_REG2_EXT_INTFACE_MASK) |
+		     FPGA_REG2_EXT_INTFACE_ENABLE);
+		mtsdr (sdr_pfc0, sdr0_pfc0);
+		mtsdr (sdr_pfc1, sdr0_pfc1);
+	} else {
+		sdr0_pfc0 = (sdr0_pfc0 & ~SDR0_PFC0_TRE_MASK) | SDR0_PFC0_TRE_ENABLE;
+		switch (group)
+		{
+		case 0:
+		case 1:
+		case 2:
+			/* CPU trace A */
+			out8(FPGA_REG2, (in8(FPGA_REG2) & ~FPGA_REG2_EXT_INTFACE_MASK) |
+			     FPGA_REG2_EXT_INTFACE_ENABLE);
+			sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_CTEMS_MASK) | SDR0_PFC1_CTEMS_EMS;
+			mtsdr (sdr_pfc0, sdr0_pfc0);
+			mtsdr (sdr_pfc1, sdr0_pfc1);
+			break;
+		case 3:
+		case 4:
+		case 5:
+		case 6:
+			/* CPU trace B - Over EBMI */
+			sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_CTEMS_MASK) | SDR0_PFC1_CTEMS_CPUTRACE;
+			mtsdr (sdr_pfc0, sdr0_pfc0);
+			mtsdr (sdr_pfc1, sdr0_pfc1);
+			out8(FPGA_REG2, (in8(FPGA_REG2) & ~FPGA_REG2_EXT_INTFACE_MASK) |
+			     FPGA_REG2_EXT_INTFACE_DISABLE);
+			break;
+		}
+	}
+
+	/* Initialize the ethernet specific functions in the fpga */
+	mfsdr(sdr_pfc1, sdr0_pfc1);
+	mfsdr(sdr_cust0, sdr0_cust0);
+	if ( (SDR0_PFC1_EPS_DECODE(sdr0_pfc1) == 4) &&
+	    ((SDR0_CUST0_RGMII2_DECODE(sdr0_cust0) == RGMII_FER_GMII) ||
+	     (SDR0_CUST0_RGMII2_DECODE(sdr0_cust0) == RGMII_FER_TBI)))
+	{
+		if ((in8(FPGA_REG0) & FPGA_REG0_ECLS_MASK) == FPGA_REG0_ECLS_VER1)
+		{
+			out8(FPGA_REG3, (in8(FPGA_REG3) & ~FPGA_REG3_ENET_MASK1) |
+			     FPGA_REG3_ENET_GROUP7);
+		}
+		else
+		{
+			if (SDR0_CUST0_RGMII2_DECODE(sdr0_cust0) == RGMII_FER_GMII)
+			{
+				out8(FPGA_REG3, (in8(FPGA_REG3) & ~FPGA_REG3_ENET_MASK2) |
+				     FPGA_REG3_ENET_GROUP7);
+			}
+			else
+			{
+				out8(FPGA_REG3, (in8(FPGA_REG3) & ~FPGA_REG3_ENET_MASK2) |
+				     FPGA_REG3_ENET_GROUP8);
+			}
+		}
+	}
+	else
+	{
+		if ((in8(FPGA_REG0) & FPGA_REG0_ECLS_MASK) == FPGA_REG0_ECLS_VER1)
+		{
+			out8(FPGA_REG3, (in8(FPGA_REG3) & ~FPGA_REG3_ENET_MASK1) |
+			     FPGA_REG3_ENET_ENCODE1(SDR0_PFC1_EPS_DECODE(sdr0_pfc1)));
+		}
+		else
+		{
+			out8(FPGA_REG3, (in8(FPGA_REG3) & ~FPGA_REG3_ENET_MASK2) |
+			     FPGA_REG3_ENET_ENCODE2(SDR0_PFC1_EPS_DECODE(sdr0_pfc1)));
+		}
+	}
+	out8(FPGA_REG4, FPGA_REG4_GPHY_MODE10 |
+	     FPGA_REG4_GPHY_MODE100 | FPGA_REG4_GPHY_MODE1000 |
+	     FPGA_REG4_GPHY_FRC_DPLX | FPGA_REG4_CONNECT_PHYS);
+
+	/* reset the gigabyte phy if necessary */
+	if (SDR0_PFC1_EPS_DECODE(sdr0_pfc1) >= 3)
+	{
+		if ((in8(FPGA_REG0) & FPGA_REG0_ECLS_MASK) == FPGA_REG0_ECLS_VER1)
+		{
+			out8(FPGA_REG3, in8(FPGA_REG3) & ~FPGA_REG3_GIGABIT_RESET_DISABLE);
+			udelay(10000);
+			out8(FPGA_REG3, in8(FPGA_REG3) | FPGA_REG3_GIGABIT_RESET_DISABLE);
+		}
+		else
+		{
+			out8(FPGA_REG2, in8(FPGA_REG2) & ~FPGA_REG2_GIGABIT_RESET_DISABLE);
+			udelay(10000);
+			out8(FPGA_REG2, in8(FPGA_REG2) | FPGA_REG2_GIGABIT_RESET_DISABLE);
+		}
+	}
+
+	/* Turn off the LED's */
+	out8(FPGA_REG3, (in8(FPGA_REG3) & ~FPGA_REG3_STAT_MASK) |
+	     FPGA_REG3_STAT_LED8_DISAB | FPGA_REG3_STAT_LED4_DISAB |
+	     FPGA_REG3_STAT_LED2_DISAB | FPGA_REG3_STAT_LED1_DISAB);
+
+	return;
+}
+
+#ifdef CONFIG_POST
+/*
+ * Returns 1 if keys pressed to start the power-on long-running tests
+ * Called from board_init_f().
+ */
+int post_hotkeys_pressed(void)
+{
+
+	return (ctrlc());
+}
+#endif
--- a/board/ocotea/ocotea.h
+++ b/board/ocotea/ocotea.h
@@ -0,0 +1,140 @@
+/*
+ * (C) Copyright 2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/* Board specific FPGA stuff ... */
+#define FPGA_REG0                       (CFG_FPGA_BASE + 0x00)
+#define   FPGA_REG0_SSCG_MASK             0x80
+#define   FPGA_REG0_SSCG_DISABLE          0x00
+#define   FPGA_REG0_SSCG_ENABLE           0x80
+#define   FPGA_REG0_BOOT_MASK             0x40
+#define   FPGA_REG0_BOOT_LARGE_FLASH      0x00
+#define   FPGA_REG0_BOOT_SMALL_FLASH      0x40
+#define   FPGA_REG0_ECLS_MASK             0x38  /* New for Ocotea Rev 2 */
+#define   FPGA_REG0_ECLS_0                0x20  /* New for Ocotea Rev 2 */
+#define   FPGA_REG0_ECLS_1                0x10  /* New for Ocotea Rev 2 */
+#define   FPGA_REG0_ECLS_2                0x08  /* New for Ocotea Rev 2 */
+#define   FPGA_REG0_ECLS_VER1             0x00  /* New for Ocotea Rev 2 */
+#define   FPGA_REG0_ECLS_VER3             0x08  /* New for Ocotea Rev 2 */
+#define   FPGA_REG0_ECLS_VER4             0x10  /* New for Ocotea Rev 2 */
+#define   FPGA_REG0_ECLS_VER5             0x18  /* New for Ocotea Rev 2 */
+#define   FPGA_REG0_ECLS_VER2             0x20  /* New for Ocotea Rev 2 */
+#define   FPGA_REG0_ECLS_VER6             0x28  /* New for Ocotea Rev 2 */
+#define   FPGA_REG0_ECLS_VER7             0x30  /* New for Ocotea Rev 2 */
+#define   FPGA_REG0_ECLS_VER8             0x38  /* New for Ocotea Rev 2 */
+#define   FPGA_REG0_ARBITER_MASK          0x04
+#define   FPGA_REG0_ARBITER_EXT           0x00
+#define   FPGA_REG0_ARBITER_INT           0x04
+#define   FPGA_REG0_ONBOARD_FLASH_MASK    0x02
+#define   FPGA_REG0_ONBOARD_FLASH_ENABLE  0x00
+#define   FPGA_REG0_ONBOARD_FLASH_DISABLE 0x02
+#define   FPGA_REG0_FLASH                 0x01
+#define FPGA_REG1                       (CFG_FPGA_BASE + 0x01)
+#define   FPGA_REG1_9772_FSELFBX_MASK     0x80
+#define   FPGA_REG1_9772_FSELFBX_6        0x00
+#define   FPGA_REG1_9772_FSELFBX_10       0x80
+#define   FPGA_REG1_9531_SX_MASK          0x60
+#define   FPGA_REG1_9531_SX_33MHZ         0x00
+#define   FPGA_REG1_9531_SX_100MHZ        0x20
+#define   FPGA_REG1_9531_SX_66MHZ         0x40
+#define   FPGA_REG1_9531_SX_133MHZ        0x60
+#define   FPGA_REG1_9772_FSELBX_MASK      0x18
+#define   FPGA_REG1_9772_FSELBX_4         0x00
+#define   FPGA_REG1_9772_FSELBX_6         0x08
+#define   FPGA_REG1_9772_FSELBX_8         0x10
+#define   FPGA_REG1_9772_FSELBX_10        0x18
+#define   FPGA_REG1_SOURCE_MASK           0x07
+#define   FPGA_REG1_SOURCE_TC             0x00
+#define   FPGA_REG1_SOURCE_66MHZ          0x01
+#define   FPGA_REG1_SOURCE_50MHZ          0x02
+#define   FPGA_REG1_SOURCE_33MHZ          0x03
+#define   FPGA_REG1_SOURCE_25MHZ          0x04
+#define   FPGA_REG1_SOURCE_SSDIV1         0x05
+#define   FPGA_REG1_SOURCE_SSDIV2         0x06
+#define   FPGA_REG1_SOURCE_SSDIV4         0x07
+#define FPGA_REG2                       (CFG_FPGA_BASE + 0x02)
+#define   FPGA_REG2_TC0                   0x80
+#define   FPGA_REG2_TC1                   0x40
+#define   FPGA_REG2_TC2                   0x20
+#define   FPGA_REG2_TC3                   0x10
+#define   FPGA_REG2_GIGABIT_RESET_DISABLE 0x08   /*Use on Ocotea pass 2 boards*/
+#define   FPGA_REG2_EXT_INTFACE_MASK      0x04
+#define   FPGA_REG2_EXT_INTFACE_ENABLE    0x00
+#define   FPGA_REG2_EXT_INTFACE_DISABLE   0x04
+#define   FPGA_REG2_DEFAULT_UART1_N       0x01
+#define FPGA_REG3                       (CFG_FPGA_BASE + 0x03)
+#define   FPGA_REG3_GIGABIT_RESET_DISABLE 0x80   /*Use on Ocotea pass 1 boards*/
+#define   FPGA_REG3_ENET_MASK1            0x70   /*Use on Ocotea pass 1 boards*/
+#define   FPGA_REG3_ENET_MASK2            0xF0   /*Use on Ocotea pass 2 boards*/
+#define   FPGA_REG3_ENET_GROUP0           0x00
+#define   FPGA_REG3_ENET_GROUP1           0x10
+#define   FPGA_REG3_ENET_GROUP2           0x20
+#define   FPGA_REG3_ENET_GROUP3           0x30
+#define   FPGA_REG3_ENET_GROUP4           0x40
+#define   FPGA_REG3_ENET_GROUP5           0x50
+#define   FPGA_REG3_ENET_GROUP6           0x60
+#define   FPGA_REG3_ENET_GROUP7           0x70
+#define   FPGA_REG3_ENET_GROUP8           0x80   /*Use on Ocotea pass 2 boards*/
+#define   FPGA_REG3_ENET_ENCODE1(n) ((((unsigned long)(n))&0x07)<<4) /*pass1*/
+#define   FPGA_REG3_ENET_DECODE1(n) ((((unsigned long)(n))>>4)&0x07) /*pass1*/
+#define   FPGA_REG3_ENET_ENCODE2(n) ((((unsigned long)(n))&0x0F)<<4) /*pass2*/
+#define   FPGA_REG3_ENET_DECODE2(n) ((((unsigned long)(n))>>4)&0x0F) /*pass2*/
+#define   FPGA_REG3_STAT_MASK             0x0F
+#define   FPGA_REG3_STAT_LED8_ENAB        0x08
+#define   FPGA_REG3_STAT_LED4_ENAB        0x04
+#define   FPGA_REG3_STAT_LED2_ENAB        0x02
+#define   FPGA_REG3_STAT_LED1_ENAB        0x01
+#define   FPGA_REG3_STAT_LED8_DISAB       0x00
+#define   FPGA_REG3_STAT_LED4_DISAB       0x00
+#define   FPGA_REG3_STAT_LED2_DISAB       0x00
+#define   FPGA_REG3_STAT_LED1_DISAB       0x00
+#define FPGA_REG4                       (CFG_FPGA_BASE + 0x04)
+#define   FPGA_REG4_GPHY_MODE10           0x80
+#define   FPGA_REG4_GPHY_MODE100          0x40
+#define   FPGA_REG4_GPHY_MODE1000         0x20
+#define   FPGA_REG4_GPHY_FRC_DPLX         0x10
+#define   FPGA_REG4_GPHY_ANEG_DIS         0x08
+#define   FPGA_REG4_CONNECT_PHYS          0x04
+
+
+#define   SDR0_CUST0_ENET3_MASK         0x00000080
+#define   SDR0_CUST0_ENET3_COPPER       0x00000000
+#define   SDR0_CUST0_ENET3_FIBER        0x00000080
+#define   SDR0_CUST0_RGMII3_MASK        0x00000070
+#define   SDR0_CUST0_RGMII3_ENCODE(n) ((((unsigned long)(n))&0x7)<<4)
+#define   SDR0_CUST0_RGMII3_DECODE(n) ((((unsigned long)(n))>>4)&0x07)
+#define   SDR0_CUST0_RGMII3_DISAB       0x00000000
+#define   SDR0_CUST0_RGMII3_RTBI        0x00000040
+#define   SDR0_CUST0_RGMII3_RGMII       0x00000050
+#define   SDR0_CUST0_RGMII3_TBI         0x00000060
+#define   SDR0_CUST0_RGMII3_GMII        0x00000070
+#define   SDR0_CUST0_ENET2_MASK         0x00000008
+#define   SDR0_CUST0_ENET2_COPPER       0x00000000
+#define   SDR0_CUST0_ENET2_FIBER        0x00000008
+#define   SDR0_CUST0_RGMII2_MASK        0x00000007
+#define   SDR0_CUST0_RGMII2_ENCODE(n) ((((unsigned long)(n))&0x7)<<0)
+#define   SDR0_CUST0_RGMII2_DECODE(n) ((((unsigned long)(n))>>0)&0x07)
+#define   SDR0_CUST0_RGMII2_DISAB       0x00000000
+#define   SDR0_CUST0_RGMII2_RTBI        0x00000004
+#define   SDR0_CUST0_RGMII2_RGMII       0x00000005
+#define   SDR0_CUST0_RGMII2_TBI         0x00000006
+#define   SDR0_CUST0_RGMII2_GMII        0x00000007
--- a/board/ocotea/u-boot.lds
+++ b/board/ocotea/u-boot.lds
@@ -0,0 +1,155 @@
+/*
+ * (C) Copyright 2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+/* Do we need any of these for elf?
+   __DYNAMIC = 0;    */
+SECTIONS
+{
+  .resetvec 0xFFFFFFFC :
+  {
+    *(.resetvec)
+  } = 0xffff
+
+  .bootpg 0xFFFFF000 :
+  {
+    cpu/ppc4xx/start.o	(.bootpg)
+  } = 0xffff
+
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)		}
+  .rela.text     : { *(.rela.text) 	}
+  .rel.data      : { *(.rel.data)		}
+  .rela.data     : { *(.rela.data) 	}
+  .rel.rodata    : { *(.rel.rodata) 	}
+  .rela.rodata   : { *(.rela.rodata) 	}
+  .rel.got       : { *(.rel.got)		}
+  .rela.got      : { *(.rela.got)		}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)		}
+  .rela.bss      : { *(.rela.bss)		}
+  .rel.plt       : { *(.rel.plt)		}
+  .rela.plt      : { *(.rela.plt)		}
+  .init          : { *(.init)	}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    /* WARNING - the following is hand-optimized to fit within	*/
+    /* the sector layout of our flash chips!	XXX FIXME XXX	*/
+
+    cpu/ppc4xx/start.o	(.text)
+    board/ocotea/init.o	(.text)
+    cpu/ppc4xx/kgdb.o	(.text)
+    cpu/ppc4xx/traps.o	(.text)
+    cpu/ppc4xx/interrupts.o	(.text)
+    cpu/ppc4xx/serial.o	(.text)
+    cpu/ppc4xx/cpu_init.o	(.text)
+    cpu/ppc4xx/speed.o	(.text)
+    cpu/ppc4xx/440gx_enet.o	(.text)
+    common/dlmalloc.o	(.text)
+    lib_generic/crc32.o		(.text)
+    lib_ppc/extable.o	(.text)
+    lib_generic/zlib.o		(.text)
+
+/*    . = env_offset;*/
+/*    common/environment.o(.text)*/
+
+    *(.text)
+    *(.fixup)
+    *(.got1)
+  }
+  _etext = .;
+  PROVIDE (etext = .);
+  .rodata    :
+  {
+    *(.rodata)
+    *(.rodata1)
+    *(.rodata.str1.4)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x00FF) & 0xFFFFFF00;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
+  __fixup_entries = (. - _FIXUP_TABLE_)>>2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  __u_boot_cmd_start = .;
+  .u_boot_cmd : { *(.u_boot_cmd) }
+  __u_boot_cmd_end = .;
+
+
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(256);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(256);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+  _end = . ;
+  PROVIDE (end = .);
+}
--- a/board/ocotea/u-boot.lds.debug
+++ b/board/ocotea/u-boot.lds.debug
@@ -0,0 +1,144 @@
+/*
+ * (C) Copyright 2002-2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+/* Do we need any of these for elf?
+   __DYNAMIC = 0;    */
+SECTIONS
+{
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)		}
+  .rela.text     : { *(.rela.text) 	}
+  .rel.data      : { *(.rel.data)		}
+  .rela.data     : { *(.rela.data) 	}
+  .rel.rodata    : { *(.rel.rodata) 	}
+  .rela.rodata   : { *(.rela.rodata) 	}
+  .rel.got       : { *(.rel.got)		}
+  .rela.got      : { *(.rela.got)		}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)		}
+  .rela.bss      : { *(.rela.bss)		}
+  .rel.plt       : { *(.rel.plt)		}
+  .rela.plt      : { *(.rela.plt)		}
+  .init          : { *(.init)	}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    /* WARNING - the following is hand-optimized to fit within	*/
+    /* the sector layout of our flash chips!	XXX FIXME XXX	*/
+
+    cpu/ppc4xx/start.o	(.text)
+    board/ocotea/init.o (.text)
+    cpu/ppc4xx/kgdb.o	(.text)
+    cpu/ppc4xx/traps.o	(.text)
+    cpu/ppc4xx/interrupts.o	(.text)
+    cpu/ppc4xx/serial.o	(.text)
+    cpu/ppc4xx/cpu_init.o	(.text)
+    cpu/ppc4xx/speed.o	(.text)
+    cpu/ppc4xx/440gx_enet.o	(.text)
+    common/dlmalloc.o	(.text)
+    lib_generic/crc32.o		(.text)
+    lib_ppc/extable.o	(.text)
+    lib_generic/zlib.o		(.text)
+
+/*    common/environment.o(.text) */
+
+    *(.text)
+    *(.fixup)
+    *(.got1)
+  }
+  _etext = .;
+  PROVIDE (etext = .);
+  .rodata    :
+  {
+    *(.rodata)
+    *(.rodata1)
+    *(.rodata.str1.4)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x0FFF) & 0xFFFFF000;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
+  __fixup_entries = (. - _FIXUP_TABLE_)>>2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  __u_boot_cmd_start = .;
+  .u_boot_cmd : { *(.u_boot_cmd) }
+  __u_boot_cmd_end = .;
+
+
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(256);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(256);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+  _end = . ;
+  PROVIDE (end = .);
+}
--- a/board/omap1610inn/omap1610innovator.c
+++ b/board/omap1610inn/omap1610innovator.c
@@ -10,6 +10,8 @@
 * Texas Instruments, <www.ti.com>
 * Kshitij Gupta <Kshitij@ti.com>
 *
+ * Modified for OMAP 1610 H2 board by Nishant Kamat, Jan 2004
+ *
 * See file CREDITS for list of people who contributed to this
 * project.
 *
@@ -105,7 +107,28 @@ void flash__init (void)
 *************************************************************/
 void ether__init (void)
 {
-#define ETH_CONTROL_REG 0x0400000b
+#define ETH_CONTROL_REG 0x0400030b
+
+#ifdef CONFIG_H2_OMAP1610
+	#define LAN_RESET_REGISTER 0x0400001c
+
+	/* The debug board on which the lan chip resides may not be powered
+	 * ON at the same time as the OMAP chip. So wait in a loop until the
+	 * lan reset register (on the debug board) is available (powered on)
+	 * and reset the lan chip.
+	 */
+
+	*((volatile unsigned short *) LAN_RESET_REGISTER) = 0x0000;
+	do {
+		*((volatile unsigned short *) LAN_RESET_REGISTER) = 0x0001;
+		udelay (3);
+	} while (*((volatile unsigned short *) LAN_RESET_REGISTER) != 0x0001);
+
+	do {
+		*((volatile unsigned short *) LAN_RESET_REGISTER) = 0x0000;
+		udelay (3);
+	} while (*((volatile unsigned short *) LAN_RESET_REGISTER) != 0x0000);
+#endif

 	*((volatile unsigned char *) ETH_CONTROL_REG) &= ~0x01;
 	udelay (3);
--- a/board/omap1610inn/platform.S
+++ b/board/omap1610inn/platform.S
@@ -5,6 +5,8 @@
 * Texas Instruments, <www.ti.com>
 * Kshitij Gupta <Kshitij@ti.com>
 *
+ * Modified for OMAP 1610 H2 board by Nishant Kamat, Jan 2004
+ *
 * See file CREDITS for list of people who contributed to this
 * project.
 *
@@ -39,6 +41,15 @@ _TEXT_BASE:
 platformsetup:


+	/*------------------------------------------------------*
+	 *mask all IRQs by setting all bits in the INTMR default*
+	 *------------------------------------------------------*/
+	mov	r1, #0xffffffff
+	ldr	r0, =REG_IHL1_MIR
+	str	r1, [r0]
+	ldr	r0, =REG_IHL2_MIR
+	str	r1, [r0]
+
 	/*------------------------------------------------------*
 	 * Set up ARM CLM registers (IDLECT1)                   *
 	 *------------------------------------------------------*/
@@ -248,6 +259,22 @@ common_tc:
 	ldr	r1,	VAL_TC_EMIFS_CS3_CONFIG
 	ldr	r0,	REG_TC_EMIFS_CS3_CONFIG
 	str	r1,	[r0] /* Chip Select 3 */
+
+#ifdef CONFIG_H2_OMAP1610
+	/* inserting additional 2 clock cycle hold time for LAN */
+	ldr     r0,     REG_TC_EMIFS_CS1_ADVANCED
+	ldr    	r1,     VAL_TC_EMIFS_CS1_ADVANCED
+	str     r1,     [r0]
+#endif
+	/* Start MPU Timer 1 */
+	ldr	r0,	REG_MPU_LOAD_TIMER
+	ldr	r1,	VAL_MPU_LOAD_TIMER
+	str	r1,	[r0]
+
+	ldr	r0,	REG_MPU_CNTL_TIMER
+	ldr	r1,	VAL_MPU_CNTL_TIMER
+	str	r1,	[r0]
+
 	/* back to arch calling code */
 	mov	pc,	lr

@@ -266,6 +293,11 @@ REG_TC_EMIFS_CS2_CONFIG:	/* 32 bits */
 REG_TC_EMIFS_CS3_CONFIG:	/* 32 bits */
 	.word 0xfffecc1c

+#ifdef CONFIG_H2_OMAP1610
+REG_TC_EMIFS_CS1_ADVANCED:	/* 32 bits */
+	.word 0xfffecc54
+#endif
+
 /* MPU clock/reset/power mode control registers */
 REG_ARM_CKCTL:			/* 16 bits */
 	.word 0xfffece00
@@ -338,6 +370,11 @@ REG_DLL_LRD_CONTROL:
 REG_WATCHDOG:
 	.word 0xfffec808

+REG_MPU_LOAD_TIMER:
+	.word 0xfffec600
+REG_MPU_CNTL_TIMER:
+	.word 0xfffec500
+
 /* 96 MHz Samsung Mobile DDR */
 SDRAM_CONFIG_VAL:
 	.word 0x001200f4
@@ -350,6 +387,7 @@ VAL_ARM_CKCTL:
 VAL_DPLL1_CTL:
 	.word 0x2830

+#ifdef CONFIG_INNOVATOROMAP1610
 VAL_TC_EMIFS_CS0_CONFIG:
 	.word 0x002130b0
 VAL_TC_EMIFS_CS1_CONFIG:
@@ -358,6 +396,21 @@ VAL_TC_EMIFS_CS2_CONFIG:
 	.word 0x000055f0
 VAL_TC_EMIFS_CS3_CONFIG:
 	.word 0x88011131
+#endif
+
+#ifdef CONFIG_H2_OMAP1610
+VAL_TC_EMIFS_CS0_CONFIG:
+	.word 0x00203331
+VAL_TC_EMIFS_CS1_CONFIG:
+	.word 0x8180fff3
+VAL_TC_EMIFS_CS2_CONFIG:
+	.word 0xf800f22a
+VAL_TC_EMIFS_CS3_CONFIG:
+	.word 0x88011131
+VAL_TC_EMIFS_CS1_ADVANCED:
+	.word 0x00000022
+#endif
+
 VAL_TC_EMIFF_SDRAM_CONFIG:
 	.word 0x010290fc
 VAL_TC_EMIFF_MRS:
@@ -376,6 +429,11 @@ WATCHDOG_VAL1:
 WATCHDOG_VAL2:
 	.word 0x000000a0

+VAL_MPU_LOAD_TIMER:
+	.word 0xffffffff
+VAL_MPU_CNTL_TIMER:
+	.word 0xffffffa1
+
 /* command values */
 .equ CMD_SDRAM_NOP,		0x00000000
 .equ CMD_SDRAM_PRECHARGE,	0x00000001
--- a/board/siemens/CCM/ccm.c
+++ b/board/siemens/CCM/ccm.c
@@ -351,7 +351,7 @@ void	reset_phy(void)
 	ulong value;

 	/* Configure all needed port pins for GPIO */
-#if CFG_ETH_MDDIS_VALUE
+#ifdef CFG_ETH_MDDIS_VALUE
 	immr->im_ioport.iop_padat |=   CFG_PA_ETH_MDDIS;
 #else
 	immr->im_ioport.iop_padat &= ~(CFG_PA_ETH_MDDIS | CFG_PA_ETH_RESET);	/* Set low */
@@ -369,17 +369,17 @@ void	reset_phy(void)
 	value |=  CFG_PB_ETH_POWERDOWN;

 	/* PHY configuration includes MDDIS and CFG1 ... CFG3 */
-#if CFG_ETH_CFG1_VALUE
+#ifdef CFG_ETH_CFG1_VALUE
 	value |=   CFG_PB_ETH_CFG1;
 #else
 	value &= ~(CFG_PB_ETH_CFG1);
 #endif
-#if CFG_ETH_CFG2_VALUE
+#ifdef CFG_ETH_CFG2_VALUE
 	value |=   CFG_PB_ETH_CFG2;
 #else
 	value &= ~(CFG_PB_ETH_CFG2);
 #endif
-#if CFG_ETH_CFG3_VALUE
+#ifdef CFG_ETH_CFG3_VALUE
 	value |=   CFG_PB_ETH_CFG3;
 #else
 	value &= ~(CFG_PB_ETH_CFG3);
--- a/board/siemens/pcu_e/pcu_e.c
+++ b/board/siemens/pcu_e/pcu_e.c
@@ -309,7 +309,7 @@ void reset_phy (void)

 	/* Configure all needed port pins for GPIO */
 #if PCU_E_WITH_SWAPPED_CS	/* XXX */
-# if CFG_ETH_MDDIS_VALUE
+# ifdef CFG_ETH_MDDIS_VALUE
 	immr->im_ioport.iop_padat |= CFG_PA_ETH_MDDIS;
 # else
 	immr->im_ioport.iop_padat &= ~(CFG_PA_ETH_MDDIS);	/* Set low */
@@ -329,23 +329,23 @@ void reset_phy (void)

 	/* PHY configuration includes MDDIS and CFG1 ... CFG3 */
 #if !PCU_E_WITH_SWAPPED_CS
-# if CFG_ETH_MDDIS_VALUE
+# ifdef CFG_ETH_MDDIS_VALUE
 	value |= CFG_PB_ETH_MDDIS;
 # else
 	value &= ~(CFG_PB_ETH_MDDIS);
 # endif
 #endif
-#if CFG_ETH_CFG1_VALUE
+#ifdef CFG_ETH_CFG1_VALUE
 	value |= CFG_PB_ETH_CFG1;
 #else
 	value &= ~(CFG_PB_ETH_CFG1);
 #endif
-#if CFG_ETH_CFG2_VALUE
+#ifdef CFG_ETH_CFG2_VALUE
 	value |= CFG_PB_ETH_CFG2;
 #else
 	value &= ~(CFG_PB_ETH_CFG2);
 #endif
-#if CFG_ETH_CFG3_VALUE
+#ifdef CFG_ETH_CFG3_VALUE
 	value |= CFG_PB_ETH_CFG3;
 #else
 	value &= ~(CFG_PB_ETH_CFG3);
--- a/board/ssv/adnpesc1/Makefile
+++ b/board/ssv/adnpesc1/Makefile
@@ -0,0 +1,48 @@
+#
+# (C) Copyright 2001-2004
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	:= $(BOARD).o flash.o misc.o
+
+SOBJS  = vectors.o
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) crv $@ $^
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+-include .depend
+
+#########################################################################
--- a/board/ssv/adnpesc1/adnpesc1.c
+++ b/board/ssv/adnpesc1/adnpesc1.c
@@ -0,0 +1,103 @@
+/*
+ * (C) Copyright 2004, Li-Pro.Net <www.li-pro.net>
+ * Stephan Linz <linz@li-pro.net>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <nios-io.h>
+#include <spi.h>
+
+#if	defined(CONFIG_HW_WATCHDOG)
+extern void ssv_wd_pio_init(void);	/* comes from ../common/wd_pio.c
+					   included by ./misc.c */
+#endif
+
+void _default_hdlr (void)
+{
+	printf ("default_hdlr\n");
+}
+
+int board_early_init_f (void)
+{
+#if	defined(CONFIG_HW_WATCHDOG)
+	ssv_wd_pio_init();
+#endif
+	return 0;
+}
+
+int checkboard (void)
+{
+	puts (	"Board: SSV DilNetPC ADNP/ESC1"
+#if	defined(CONFIG_DNPEVA2)
+		" on DNP/EVA2"
+#endif
+		"\n");
+#if     defined(CONFIG_NIOS_BASE_32)
+	puts ("Conf.: SSV Base 32 (nios_32)\n");
+#endif
+
+	return 0;
+}
+
+long int initdram (int board_type)
+{
+	return (0);
+}
+
+/*
+ * The following are used to control the SPI chip selects for the SPI command.
+ */
+#if (CONFIG_COMMANDS & CFG_CMD_SPI) && CONFIG_NIOS_SPI
+
+#define	SPI_RTC_CS_MASK	0x00000001
+
+void spi_rtc_chipsel(int cs)
+{
+	nios_spi_t *spi = (nios_spi_t *)CFG_NIOS_SPIBASE;
+
+	if (cs)
+		spi->slaveselect = SPI_RTC_CS_MASK;	/* activate (1) */
+	else
+		spi->slaveselect = 0;			/* deactivate (0) */
+}
+
+/*
+ * The SPI command uses this table of functions for controlling the SPI
+ * chip selects: it calls the appropriate function to control the SPI
+ * chip selects.
+ */
+spi_chipsel_type spi_chipsel[] = {
+	spi_rtc_chipsel
+};
+int spi_chipsel_cnt = sizeof(spi_chipsel) / sizeof(spi_chipsel[0]);
+
+#endif /* CFG_CMD_SPI */
+
+#if	defined(CONFIG_POST)
+/*
+ * Returns 1 if keys pressed to start the power-on long-running tests
+ * Called from board_init_f().
+ */
+int post_hotkeys_pressed(void)
+{
+	return 0;       /* No hotkeys supported */
+}
+#endif /* CONFIG_POST */
--- a/board/ssv/adnpesc1/config.mk
+++ b/board/ssv/adnpesc1/config.mk
@@ -0,0 +1,29 @@
+#
+# (C) Copyright 2004
+# Li-Pro.Net <www.li-pro.net>
+# Stephan Linz <linz@li-pro.net>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+TEXT_BASE = 0x02fc0000	# ATTENTION: notice your CFG_MONITOR_LEN setting
+
+ifeq ($(debug),1)
+PLATFORM_CPPFLAGS += -DDEBUG
+endif
--- a/board/ssv/adnpesc1/flash.c
+++ b/board/ssv/adnpesc1/flash.c
@@ -0,0 +1,66 @@
+/*
+ * (C) Copyright 2000-2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * (C) Copyright 2004, Li-Pro.Net <www.li-pro.net>
+ * Stephan Linz <linz@li-pro.net>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+
+#include <common.h>
+#include <nios.h>
+
+/*
+ * include common flash code (for ssv boards)
+ */
+#include "../common/flash.c"
+
+/*---------------------------------------------------------------------*/
+#define	BANKSZ	(8 * 1024 * 1024)
+#define	SECTSZ	(64 * 1024)
+#define	UBOOTSECS ((CFG_MONITOR_LEN + CFG_ENV_SIZE) / SECTSZ)
+#define	UBOOTAREA (UBOOTSECS * 64 * 1024)	/* monitor / env area */
+
+/*---------------------------------------------------------------------*/
+unsigned long flash_init (void)
+{
+	int i;
+	unsigned long addr;
+	flash_info_t *fli = &flash_info[0];
+
+	fli->size = BANKSZ;
+	fli->sector_count = CFG_MAX_FLASH_SECT;
+	fli->flash_id = FLASH_MAN_AMD + FLASH_AMLV640U;
+
+	addr = CFG_FLASH_BASE;
+	for (i = 0; i < fli->sector_count; ++i) {
+		fli->start[i] = addr;
+		addr += SECTSZ;
+
+		/* Protect monitor / environment area */
+		if (addr <= (CFG_FLASH_BASE + UBOOTAREA))
+			fli->protect[i] = 1;
+		else
+			fli->protect[i] = 0;
+	}
+
+	return (BANKSZ);
+}
--- a/board/ssv/adnpesc1/misc.c
+++ b/board/ssv/adnpesc1/misc.c
@@ -0,0 +1,40 @@
+/*
+ * (C) Copyright 2003, Li-Pro.Net <www.li-pro.net>
+ * Stephan Linz <linz@li-pro.net>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ * board/ssv/adnpesc1/misc.c
+ *
+ * miscellaneous board interfaces / drivers
+ */
+
+#include <common.h>
+
+#if	defined(CONFIG_STATUS_LED)
+#include "../common/cmd_sled.c"
+#endif
+
+#if	defined(CONFIG_HW_WATCHDOG)
+#include "../common/wd_pio.c"
+#endif
+
+#if	defined(CONFIG_POST) || defined(CONFIG_LOGBUFFER)
+#include "../common/post.c"
+#endif
--- a/board/ssv/adnpesc1/u-boot.lds
+++ b/board/ssv/adnpesc1/u-boot.lds
@@ -0,0 +1,69 @@
+/*
+ * (C) Copyright 2003, Psyent Corporation <www.psyent.com>
+ * Scott McNutt <smcnutt@psyent.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+
+OUTPUT_FORMAT("elf32-nios")
+OUTPUT_ARCH(nios)
+ENTRY(_start)
+
+SECTIONS
+{
+	.text :
+	{
+	  cpu/nios/start.o (.text)
+	  *(.text)
+	}
+	__text_end = .;
+
+	. = ALIGN(4);
+	.rodata :
+	{
+		*(.rodata)
+	}
+	__rodata_end = .;
+
+	. = ALIGN(4);
+	.data :
+	{
+		*(.data)
+	}
+	. = ALIGN(4);
+	__data_end = .;
+
+	__u_boot_cmd_start = .;
+	.u_boot_cmd :
+	{
+		*(.u_boot_cmd)
+	}
+	. = ALIGN(4);
+	__u_boot_cmd_end = .;
+
+	__bss_start = .;
+	. = ALIGN(4);
+	.bss :
+	{
+		*(.bss)
+	}
+	. = ALIGN(4);
+	__bss_end = .;
+}
--- a/board/ssv/adnpesc1/vectors.S
+++ b/board/ssv/adnpesc1/vectors.S
@@ -0,0 +1,138 @@
+/*
+ * (C) Copyright 2004, Li-Pro.Net <www.li-pro.net>
+ * Stephan Linz <linz@li-pro.net>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+
+
+/*************************************************************************
+ * Exception Vector Table
+ *
+ * This could have gone in the cpu soure tree, but the whole point of
+ * Nios is customization -- and polluting the cpu source tree with
+ * board-specific ifdef's really defeats the purpose, no? With this in
+ * the board-specific tree, each board has the freedom to organize
+ * vectors/traps, etc anyway it wants. The init code copies this table
+ * to the proper location.
+ *
+ * Each board can do what it likes here. But there are four "standard"
+ * handlers availble:
+ *
+ *	_cwp_lolimit	-Handles register window underflows.
+ *	_cwp_hilimit	-Handles register window overflows.
+ *	_timebase_int	-Increments the timebase.
+ *	_def_xhandler	-Default exception handler.
+ *
+ * _timebase_int handles a Nios Timer interrupt and increments the
+ * timestamp used for the get_timer(), reset_timer(), etc. routines. It
+ * expects the timer to be configured like the standard-32 low priority
+ * timer.
+ *
+ * _def_xhandler dispatches exceptions/traps via the external_interrupt()
+ * routine. This lets you use the irq_install_handler() and handle your
+ * interrupts/traps with code written in C.
+ ************************************************************************/
+
+	.data
+	.global _vectors
+	.align	4
+_vectors:
+
+#if	defined(CFG_NIOS_CPU_OCI_BASE)
+	/* OCI does the reset job */
+	.long	_def_xhandler@h		/* Vector 0  - NMI / Reset */
+#else
+	/* there is no OCI, so we have to do a direct reset jump here */
+	.long	CFG_NIOS_CPU_RST_VECT	/* Vector 0  - Reset to GERMS */
+#endif
+	.long	_cwp_lolimit@h		/* Vector 1  - underflow */
+	.long	_cwp_hilimit@h		/* Vector 2  - overflow	*/
+
+	.long	_def_xhandler@h		/* Vector 3 - GNUPro debug */
+	.long	_def_xhandler@h		/* Vector 4 - GNUPro debug */
+	.long	_def_xhandler@h		/* Vector 5 - GNUPro debug */
+	.long	_def_xhandler@h		/* Vector 6 - future reserved */
+	.long	_def_xhandler@h		/* Vector 7 - future reserved */
+	.long	_def_xhandler@h		/* Vector 8 - future reserved */
+	.long	_def_xhandler@h		/* Vector 9 - future reserved */
+	.long	_def_xhandler@h		/* Vector 10 - future reserved */
+	.long	_def_xhandler@h		/* Vector 11 - future reserved */
+	.long	_def_xhandler@h		/* Vector 12 - future reserved */
+	.long	_def_xhandler@h		/* Vector 13 - future reserved */
+	.long	_def_xhandler@h		/* Vector 14 - future reserved */
+	.long	_def_xhandler@h		/* Vector 15 - future reserved */
+#if	(CFG_NIOS_TMRIRQ == 16)
+	.long	_timebase_int@h		/* Vector 16 - lopri timer*/
+#else
+	.long	_def_xhandler@h		/* Vector 16 */
+#endif
+	.long	_def_xhandler@h		/* Vector 17 */
+	.long	_def_xhandler@h		/* Vector 18 */
+	.long	_def_xhandler@h		/* Vector 19 */
+	.long	_def_xhandler@h		/* Vector 20 */
+	.long	_def_xhandler@h		/* Vector 21 */
+	.long	_def_xhandler@h		/* Vector 22 */
+	.long	_def_xhandler@h		/* Vector 23 */
+	.long	_def_xhandler@h		/* Vector 24 */
+	.long	_def_xhandler@h		/* Vector 25 */
+	.long	_def_xhandler@h		/* Vector 26 */
+	.long	_def_xhandler@h		/* Vector 27 */
+	.long	_def_xhandler@h		/* Vector 28 */
+	.long	_def_xhandler@h		/* Vector 29 */
+	.long	_def_xhandler@h		/* Vector 30 */
+	.long	_def_xhandler@h		/* Vector 31 */
+	.long	_def_xhandler@h		/* Vector 32 */
+	.long	_def_xhandler@h		/* Vector 33 */
+	.long	_def_xhandler@h		/* Vector 34 */
+	.long	_def_xhandler@h		/* Vector 35 */
+	.long	_def_xhandler@h		/* Vector 36 */
+	.long	_def_xhandler@h		/* Vector 37 */
+	.long	_def_xhandler@h		/* Vector 38 */
+	.long	_def_xhandler@h		/* Vector 39 */
+	.long	_def_xhandler@h		/* Vector 40 */
+	.long	_def_xhandler@h		/* Vector 41 */
+	.long	_def_xhandler@h		/* Vector 42 */
+	.long	_def_xhandler@h		/* Vector 43 */
+	.long	_def_xhandler@h		/* Vector 44 */
+	.long	_def_xhandler@h		/* Vector 45 */
+	.long	_def_xhandler@h		/* Vector 46 */
+	.long	_def_xhandler@h		/* Vector 47 */
+	.long	_def_xhandler@h		/* Vector 48 */
+	.long	_def_xhandler@h		/* Vector 49 */
+#if	(CFG_NIOS_TMRIRQ == 50)
+	.long	_timebase_int@h		/* Vector 50 - lopri timer*/
+#else
+	.long	_def_xhandler@h		/* Vector 50 */
+#endif
+	.long	_def_xhandler@h		/* Vector 51 */
+	.long	_def_xhandler@h		/* Vector 52 */
+	.long	_def_xhandler@h		/* Vector 53 */
+	.long	_def_xhandler@h		/* Vector 54 */
+	.long	_def_xhandler@h		/* Vector 55 */
+	.long	_def_xhandler@h		/* Vector 56 */
+	.long	_def_xhandler@h		/* Vector 57 */
+	.long	_def_xhandler@h		/* Vector 58 */
+	.long	_def_xhandler@h		/* Vector 59 */
+	.long	_def_xhandler@h		/* Vector 60 */
+	.long	_def_xhandler@h		/* Vector 61 */
+	.long	_def_xhandler@h		/* Vector 62 */
+	.long	_def_xhandler@h		/* Vector 63 */
--- a/board/ssv/common/cmd_sled.c
+++ b/board/ssv/common/cmd_sled.c
@@ -0,0 +1,162 @@
+/*
+ * (C) Copyright 2004, Li-Pro.Net <www.li-pro.net>
+ * Stephan Linz <linz@li-pro.net>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <status_led.h>
+
+#if	defined(CONFIG_STATUS_LED)
+
+/* !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
+ * !!!!!       Q u i c k   &   D i r t y   H a c k	 !!!!!
+ * !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
+ * !!!!!						 !!!!!
+ * !!!!! Next type definition was coming from original	 !!!!!
+ * !!!!! status LED driver drivers/status_led.c and	 !!!!!
+ * !!!!! should exported for using here.		 !!!!!
+ * !!!!!						 !!!!!
+ * !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! */
+
+typedef struct {
+	led_id_t mask;
+	int state;
+	int period;
+	int cnt;
+} led_dev_t;
+
+extern led_dev_t led_dev[];
+
+#if (CONFIG_COMMANDS & CFG_CMD_BSP)
+int do_sled (cmd_tbl_t * cmdtp, int flag, int argc, char *argv[])
+{
+	int led_id = 0;
+
+	if (argc > 1) {
+#ifdef	STATUS_LED_BOOT
+		if (!strcmp (argv[1], "boot")) {
+			led_id = STATUS_LED_BOOT + 1;
+		}
+#endif
+#ifdef	STATUS_LED_RED
+		if (!strcmp (argv[1], "red")) {
+			led_id = STATUS_LED_RED + 1;
+		}
+#endif
+#ifdef	STATUS_LED_YELLOW
+		if (!strcmp (argv[1], "yellow")) {
+			led_id = STATUS_LED_YELLOW + 1;
+		}
+#endif
+#ifdef	STATUS_LED_GREEN
+		if (!strcmp (argv[1], "green")) {
+			led_id = STATUS_LED_GREEN + 1;
+		}
+#endif
+	}
+
+	switch (argc) {
+	case 1:
+#if	(STATUS_LED_BITS > 3)
+		for (; led_id < 4; led_id++)
+#elif	(STATUS_LED_BITS > 2)
+		for (; led_id < 3; led_id++)
+#elif	(STATUS_LED_BITS > 1)
+		for (; led_id < 2; led_id++)
+#elif	(STATUS_LED_BITS > 0)
+		for (; led_id < 1; led_id++)
+#else
+#error "*** STATUS_LED_BITS not correct defined ***"
+#endif
+		{
+			printf ("Status LED '%s' is %s\n",
+				led_id == STATUS_LED_BOOT ? "boot"
+				: led_id == STATUS_LED_RED ? "red"
+				: led_id == STATUS_LED_YELLOW ? "yellow"
+				: led_id ==
+				STATUS_LED_GREEN ? "green" : "unknown",
+				led_dev[led_id].state ==
+				STATUS_LED_ON ? "on" : led_dev[led_id].
+				state ==
+				STATUS_LED_OFF ? "off" : led_dev[led_id].
+				state ==
+				STATUS_LED_BLINKING ? "blinking" : "unknown");
+		}
+		return 0;
+	case 2:
+		if (led_id) {
+			printf ("Status LED '%s' is %s\n", argv[1],
+				led_dev[led_id - 1].state ==
+				STATUS_LED_ON ? "on" : led_dev[led_id -
+							       1].state ==
+				STATUS_LED_OFF ? "off" : led_dev[led_id -
+								 1].state ==
+				STATUS_LED_BLINKING ? "blinking" : "unknown");
+			return 0;
+		} else
+			break;
+	case 3:
+		if (led_id) {
+			if (!strcmp (argv[2], "on")) {
+				status_led_set (led_id - 1, STATUS_LED_ON);
+				return 0;
+			} else if (!strcmp (argv[2], "off")) {
+				status_led_set (led_id - 1, STATUS_LED_OFF);
+				return 0;
+			} else if (!strcmp (argv[2], "blink")) {
+				status_led_set (led_id - 1,
+						STATUS_LED_BLINKING);
+				return 0;
+			} else
+				break;
+		} else
+			break;
+	default:
+		break;
+	}
+	printf ("Usage:\n%s\n", cmdtp->usage);
+	return 1;
+}
+
+#ifdef	STATUS_LED_BOOT
+#ifdef	STATUS_LED_RED
+#ifdef	STATUS_LED_YELLOW
+#ifdef	STATUS_LED_GREEN
+#define __NAME_STR		"    - name: boot|red|yellow|green\n"
+#else
+#define __NAME_STR		"    - name: boot|red|yellow\n"
+#endif
+#else
+#define __NAME_STR		"    - name: boot|red\n"
+#endif
+#else
+#define __NAME_STR		"    - name: boot\n"
+#endif
+#else
+#define __NAME_STR		"    - name: (no such defined)\n"
+#endif
+
+U_BOOT_CMD (sled, 3, 0, do_sled,
+	    "sled    - check and set status led\n",
+	    "sled [name [state]]\n" __NAME_STR "    - state: on|off|blink\n");
+#endif /* CFG_CMD_BSP */
+#endif	/* CONFIG_STATUS_LED */
--- a/board/ssv/common/flash.c
+++ b/board/ssv/common/flash.c
@@ -0,0 +1,207 @@
+/*
+ * (C) Copyright 2000-2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * (C) Copyright 2004, Li-Pro.Net <www.li-pro.net>
+ * Stephan Linz <linz@li-pro.net>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+
+#include <common.h>
+#include <watchdog.h>
+#include <nios.h>
+
+flash_info_t flash_info[CFG_MAX_FLASH_BANKS];
+
+/*--------------------------------------------------------------------*/
+void flash_print_info (flash_info_t * info)
+{
+	int i, k;
+	unsigned long size;
+	int erased;
+	volatile unsigned char *flash;
+
+	printf ("  Size: %ld KB in %d Sectors\n",
+		info->size >> 10, info->sector_count);
+	printf ("  Sector Start Addresses:");
+	for (i = 0; i < info->sector_count; ++i) {
+
+		/* Check if whole sector is erased */
+		if (i != (info->sector_count - 1))
+			size = info->start[i + 1] - info->start[i];
+		else
+			size = info->start[0] + info->size - info->start[i];
+		erased = 1;
+		flash = (volatile unsigned char *) info->start[i];
+		for (k = 0; k < size; k++) {
+			if (*flash++ != 0xff) {
+				erased = 0;
+				break;
+			}
+		}
+
+		/* Print the info */
+		if ((i % 5) == 0)
+			printf ("\n   ");
+		printf (" %08lX%s%s", info->start[i], erased ? " E" : "  ",
+			info->protect[i] ? "RO " : "   ");
+	}
+	printf ("\n");
+}
+
+/*-------------------------------------------------------------------*/
+
+
+int flash_erase (flash_info_t * info, int s_first, int s_last)
+{
+	volatile CFG_FLASH_WORD_SIZE *addr = (CFG_FLASH_WORD_SIZE *) (info->start[0]);
+	volatile CFG_FLASH_WORD_SIZE *addr2;
+	int prot, sect, wait;
+	unsigned oldpri;
+	ulong start;
+
+	/* Some sanity checking */
+	if ((s_first < 0) || (s_first > s_last)) {
+		printf ("- no sectors to erase\n");
+		return 1;
+	}
+
+	prot = 0;
+	for (sect = s_first; sect <= s_last; ++sect) {
+		if (info->protect[sect]) {
+			prot++;
+		}
+	}
+	if (prot) {
+		printf ("- Warning: %d protected sectors will not be erased!\n",
+			prot);
+	} else {
+		printf ("\n");
+	}
+
+#ifdef DEBUG
+	for (sect = s_first; sect <= s_last; sect++) {
+		printf("- Erase: Sect: %i @ 0x%08x\n", sect,  info->start[sect]);
+	}
+#endif
+
+	/* NOTE: disabling interrupts on Nios can be very bad since it
+	 * also disables the LO_LIMIT exception. It's better here to
+	 * set the interrupt priority to 3 & restore it when we're done.
+	 */
+	oldpri = ipri (3);
+
+	/* It's ok to erase multiple sectors provided we don't delay more
+	 * than 50 usec between cmds ... at which point the erase time-out
+	 * occurs. So don't go and put printf() calls in the loop ... it
+	 * won't be very helpful ;-)
+	 */
+	for (sect = s_first; sect <= s_last; sect++) {
+		if (info->protect[sect] == 0) {	/* not protected */
+			addr2 = (CFG_FLASH_WORD_SIZE *) (info->start[sect]);
+			*addr = 0xf0;
+			*(addr+0xAAA/2) = 0xaa;
+			*(addr+0x554/2) = 0x55;
+			*(addr+0xAAA/2) = 0x80;
+			*(addr+0xAAA/2) = 0xaa;
+			*(addr+0x554/2) = 0x55;
+			*addr2 = 0x30;
+			/* Now just wait for 0xffff & provide some user
+			 * feedback while we wait. Here we have to grant
+			 * timer interrupts. Otherwise get_timer() can't
+			 * work right. */
+			ipri(oldpri);
+			start = get_timer (0);
+			while (*addr2 != 0xffff) {
+				for (wait = 8; wait; wait--) {
+					udelay (125 * 1000);
+				}
+				putc ('.');
+				if (get_timer (start) > CFG_FLASH_ERASE_TOUT) {
+					printf ("timeout\n");
+					return 1;
+				}
+			}
+			oldpri = ipri (3); /* disallow non important irqs again */
+		}
+	}
+
+	printf ("\n");
+	*addr = 0xf0;
+
+	/* Restore interrupt priority */
+	ipri (oldpri);
+
+	return 0;
+}
+
+/*-----------------------------------------------------------------------
+ * Copy memory to flash, returns:
+ * 0 - OK
+ * 1 - write timeout
+ * 2 - Flash not erased
+ */
+
+int write_buff (flash_info_t * info, uchar * srcbuffer, ulong addr, ulong cnt)
+{
+
+	volatile CFG_FLASH_WORD_SIZE *cmd = (vu_short *) info->start[0];
+	volatile CFG_FLASH_WORD_SIZE *dst = (vu_short *) addr;
+	CFG_FLASH_WORD_SIZE *src = (void *) srcbuffer;
+	CFG_FLASH_WORD_SIZE b;
+	unsigned oldpri;
+	ulong start;
+
+	cnt /= sizeof(CFG_FLASH_WORD_SIZE);
+	while (cnt) {
+		/* Check for sufficient erase */
+		b = *src;
+		if ((*dst & b) != b) {
+			printf ("%02x : %02x\n", *dst, b);
+			return (2);
+		}
+
+		/* Disable interrupts other than window underflow
+		 * (interrupt priority 2)
+		 */
+		oldpri = ipri (3);
+		*(cmd+0xAAA/2) = 0xaa;
+		*(cmd+0x554/2) = 0x55;
+		*(cmd+0xAAA/2) = 0xa0;
+		ipri (oldpri);
+		*dst = b;
+
+		/* Verify write */
+		start = get_timer (0);
+		while (*dst != b) {
+			if (get_timer (start) > CFG_FLASH_WRITE_TOUT) {
+				*cmd = 0xf0;
+				return 1;
+			}
+		}
+		dst++;
+		src++;
+		cnt--;
+	}
+
+	*cmd = 0xf0;
+	return (0);
+}
--- a/board/ssv/common/post.c
+++ b/board/ssv/common/post.c
@@ -0,0 +1,44 @@
+/*
+ * (C) Copyright 2004, Li-Pro.Net <www.li-pro.net>
+ * Stephan Linz <linz@li-pro.net>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+
+#if defined(CONFIG_POST) || defined(CONFIG_LOGBUFFER)
+
+#if !defined(CFG_NIOS_POST_WORD_ADDR)
+#error "*** CFG_NIOS_POST_WORD_ADDR not defined ***"
+#endif
+
+void post_word_store (ulong a)
+{
+	volatile void *save_addr = (void *)(CFG_NIOS_POST_WORD_ADDR);
+	*(volatile ulong *) save_addr = a;
+}
+
+ulong post_word_load (void)
+{
+	volatile void *save_addr = (void *)(CFG_NIOS_POST_WORD_ADDR);
+	return *(volatile ulong *) save_addr;
+}
+
+#endif	/* CONFIG_POST || CONFIG_LOGBUFFER*/
--- a/board/ssv/common/wd_pio.c
+++ b/board/ssv/common/wd_pio.c
@@ -0,0 +1,160 @@
+/*
+ * (C) Copyright 2004, Li-Pro.Net <www.li-pro.net>
+ * Stephan Linz <linz@li-pro.net>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <nios.h>
+#include <nios-io.h>
+
+#if	defined(CONFIG_HW_WATCHDOG)
+
+#if !defined(CONFIG_HW_WDENA_BASE)
+#error "*** CONFIG_HW_WDENA_BASE not defined ***"
+#if !defined(CONFIG_HW_WDENA_BIT)
+#error "*** CONFIG_HW_WDENA_BIT not defined ***"
+#endif
+#endif
+
+#if !defined(CONFIG_HW_WDTOG_BASE)
+#error "*** CONFIG_HW_WDTOG_BASE not defined ***"
+#if !defined(CONFIG_HW_WDTOG_BIT)
+#error "*** CONFIG_HW_WDTOG_BIT not defined ***"
+#endif
+#endif
+
+#ifdef	CONFIG_HW_WDPORT_WRONLY	/* emulate read access */
+static unsigned __wd_ena_pio_portval = 0;
+#endif
+
+#define	WD_PIO_INIT_DONE(V)	((V) & (1 << CONFIG_HW_WDENA_BIT))
+
+void ssv_wd_pio_init(void)
+{
+	nios_pio_t *ena_piop	 = (nios_pio_t*)CONFIG_HW_WDENA_BASE;
+	nios_pio_t *trg_piop	 = (nios_pio_t*)CONFIG_HW_WDTOG_BASE;
+
+	trg_piop->data		&= ~(1 << CONFIG_HW_WDTOG_BIT);
+
+#ifdef	CONFIG_HW_WDPORT_WRONLY	/* emulate read access */
+
+	__wd_ena_pio_portval	|= (1 << CONFIG_HW_WDENA_BIT);
+	ena_piop->data		 = __wd_ena_pio_portval;
+
+#else	/* !CONFIG_HW_WDPORT_WRONLY */
+
+	trg_piop->direction	|= (1 << CONFIG_HW_WDTOG_BIT);
+
+	ena_piop->data		|= (1 << CONFIG_HW_WDENA_BIT);
+	ena_piop->direction	|= (1 << CONFIG_HW_WDENA_BIT);
+
+#endif	/* CONFIG_HW_WDPORT_WRONLY */
+}
+
+void ssv_wd_pio_done(void)
+{
+	nios_pio_t *piop	 = (nios_pio_t*)CONFIG_HW_WDENA_BASE;
+
+#ifdef	CONFIG_HW_WDPORT_WRONLY	/* emulate read access */
+
+	__wd_ena_pio_portval	&= ~(1 << CONFIG_HW_WDENA_BIT);
+	piop->data		 = __wd_ena_pio_portval;
+
+#else	/* !CONFIG_HW_WDPORT_WRONLY */
+
+	piop->data		&= ~(1 << CONFIG_HW_WDENA_BIT);
+
+#endif	/* CONFIG_HW_WDPORT_WRONLY */
+}
+
+void ssv_wd_pio_reset(void)
+{
+	nios_pio_t *trg_piop	 = (nios_pio_t*)CONFIG_HW_WDTOG_BASE;
+
+#ifdef	CONFIG_HW_WDPORT_WRONLY
+	if (WD_PIO_INIT_DONE(__wd_ena_pio_portval))
+#else
+	nios_pio_t *ena_piop	 = (nios_pio_t*)CONFIG_HW_WDENA_BASE;
+
+	if (WD_PIO_INIT_DONE(ena_piop->data))
+#endif
+	{
+		trg_piop->data	|=  (1 << CONFIG_HW_WDTOG_BIT);
+		trg_piop->data	&= ~(1 << CONFIG_HW_WDTOG_BIT);
+	}
+}
+
+void hw_watchdog_reset(void)
+{
+	int re_enable = disable_interrupts ();
+
+	ssv_wd_pio_reset();
+	if (re_enable)
+		enable_interrupts ();
+}
+
+#if (CONFIG_COMMANDS & CFG_CMD_BSP)
+int do_wd (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+	nios_pio_t *ena_piop	 = (nios_pio_t*)CONFIG_HW_WDENA_BASE;
+
+	switch (argc)
+	{
+	case 1:
+		printf ("Watchdog timer status is %s\n",
+#ifdef	CONFIG_HW_WDPORT_WRONLY
+				WD_PIO_INIT_DONE(__wd_ena_pio_portval)
+#else
+				WD_PIO_INIT_DONE(ena_piop->data)
+#endif
+				? "on" : "off");
+		return 0;
+	case 2:
+		if (!strcmp(argv[1],"on"))
+		{
+			ssv_wd_pio_init();
+			printf("Watchdog timer now is on\n");
+			return 0;
+		}
+		else if (!strcmp(argv[1],"off"))
+		{
+			ssv_wd_pio_done();
+			printf("Watchdog timer now is off\n");
+			return 0;
+		}
+		break;
+	default:
+		break;
+	}
+	printf ("Usage:\n%s\n", cmdtp->usage);
+	return 1;
+}
+
+U_BOOT_CMD(
+	wd,	2,	1,	do_wd,
+	"wd      - check and set watchdog\n",
+	"on   - switch watchDog on\n"
+	"wd off  - switch watchdog off\n"
+	"wd      - print current status\n"
+);
+#endif	/* CFG_CMD_BSP */
+#endif	/* CONFIG_HW_WATCHDOG */
--- a/board/sx1/Makefile
+++ b/board/sx1/Makefile
@@ -0,0 +1,47 @@
+#
+# (C) Copyright 2004
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	:= sx1.o flash.o
+SOBJS	:= platform.o
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) crv $@ $^
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+-include .depend
+
+#########################################################################
--- a/board/sx1/config.mk
+++ b/board/sx1/config.mk
@@ -0,0 +1,19 @@
+#
+# (C) Copyright 2004
+# Wolfgang Denk, DENX Software Engineering, <wd@denx.de>
+#
+# SX1 board with OMAP1510 (ARM925T) cpu
+# see http://www.ti.com/ for more information on Texas Insturments
+#
+# SX1 has 1 bank of 256 MB SDRAM
+# Physical Address:
+# 1000'0000 to 2000'0000
+#
+#
+# Linux-Kernel is expected to be at 1000'8000, entry 1000'8000  (mem base + reserved)
+#
+# we load ourself to 1108'0000
+#
+#
+
+TEXT_BASE = 0x11080000
--- a/board/sx1/flash.c
+++ b/board/sx1/flash.c
@@ -0,0 +1,444 @@
+/*
+ * (C) Copyright 2001
+ * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net
+ *
+ * (C) Copyright 2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <linux/byteorder/swab.h>
+#include <environment.h>
+
+#define PHYS_FLASH_SECT_SIZE	0x00020000	/* 256 KB sectors (x2) */
+flash_info_t flash_info[CFG_MAX_FLASH_BANKS];	/* info for FLASH chips	   */
+
+/* Board support for 1 or 2 flash devices */
+#undef FLASH_PORT_WIDTH32
+#define FLASH_PORT_WIDTH16
+
+#ifdef FLASH_PORT_WIDTH16
+#define FLASH_PORT_WIDTH	ushort
+#define FLASH_PORT_WIDTHV	vu_short
+#define SWAP(x)			__swab16(x)
+#else
+#define FLASH_PORT_WIDTH	ulong
+#define FLASH_PORT_WIDTHV	vu_long
+#define SWAP(x)			__swab32(x)
+#endif
+
+#define FPW	FLASH_PORT_WIDTH
+#define FPWV	FLASH_PORT_WIDTHV
+
+#define mb() __asm__ __volatile__ ("" : : : "memory")
+
+/*-----------------------------------------------------------------------
+ * Functions
+ */
+static ulong flash_get_size (FPW * addr, flash_info_t * info);
+static int write_data (flash_info_t * info, ulong dest, FPW data);
+static void flash_get_offsets (ulong base, flash_info_t * info);
+void inline spin_wheel (void);
+
+/*-----------------------------------------------------------------------
+ */
+
+unsigned long flash_init (void)
+{
+	int i;
+	ulong size = 0;
+
+	for (i = 0; i < CFG_MAX_FLASH_BANKS; i++) {
+		switch (i) {
+		case 0:
+			flash_get_size ((FPW *) PHYS_FLASH_1, &flash_info[i]);
+			flash_get_offsets (PHYS_FLASH_1, &flash_info[i]);
+			break;
+		case 1:
+			flash_get_size ((FPW *) PHYS_FLASH_2, &flash_info[i]);
+			flash_get_offsets (PHYS_FLASH_2, &flash_info[i]);
+			break;
+		default:
+			panic ("configured too many flash banks!\n");
+			break;
+		}
+		size += flash_info[i].size;
+	}
+
+	/* Protect monitor and environment sectors
+	 */
+	flash_protect ( FLAG_PROTECT_SET,
+			CFG_FLASH_BASE,
+			CFG_FLASH_BASE + monitor_flash_len - 1,
+			&flash_info[0]);
+
+	flash_protect ( FLAG_PROTECT_SET,
+			CFG_ENV_ADDR,
+			CFG_ENV_ADDR + CFG_ENV_SIZE - 1,
+			&flash_info[0]);
+
+#ifdef CFG_ENV_ADDR_REDUND
+	flash_protect ( FLAG_PROTECT_SET,
+			CFG_ENV_ADDR_REDUND,
+			CFG_ENV_ADDR_REDUND + CFG_ENV_SIZE_REDUND - 1,
+			&flash_info[0]);
+#endif
+
+	return size;
+}
+
+/*-----------------------------------------------------------------------
+ */
+static void flash_get_offsets (ulong base, flash_info_t * info)
+{
+	int i;
+
+	if (info->flash_id == FLASH_UNKNOWN) {
+		return;
+	}
+
+	if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL) {
+		for (i = 0; i < info->sector_count; i++) {
+			info->start[i] = base + (i * PHYS_FLASH_SECT_SIZE);
+			info->protect[i] = 0;
+		}
+	}
+}
+
+/*-----------------------------------------------------------------------
+ */
+void flash_print_info (flash_info_t * info)
+{
+	int i;
+
+	if (info->flash_id == FLASH_UNKNOWN) {
+		printf ("missing or unknown FLASH type\n");
+		return;
+	}
+
+	switch (info->flash_id & FLASH_VENDMASK) {
+	case FLASH_MAN_INTEL:
+		printf ("INTEL ");
+		break;
+	default:
+		printf ("Unknown Vendor ");
+		break;
+	}
+
+	switch (info->flash_id & FLASH_TYPEMASK) {
+	case FLASH_28F128J3A:
+		printf ("28F128J3A\n");
+		break;
+	case FLASH_28F640J3A:
+		printf ("28F640J3A\n");
+		break;
+	default:
+		printf ("Unknown Chip Type\n");
+		break;
+	}
+
+	printf ("  Size: %ld MB in %d Sectors\n",
+		info->size >> 20, info->sector_count);
+
+	printf ("  Sector Start Addresses:");
+	for (i = 0; i < info->sector_count; ++i) {
+		if ((i % 5) == 0)
+			printf ("\n   ");
+		printf (" %08lX%s",
+			info->start[i],
+			info->protect[i] ? " (RO)" : "	   ");
+	}
+	printf ("\n");
+	return;
+}
+
+/*
+ * The following code cannot be run from FLASH!
+ */
+static ulong flash_get_size (FPW * addr, flash_info_t * info)
+{
+	volatile FPW value;
+
+	/* Write auto select command: read Manufacturer ID */
+	addr[0x5555] = (FPW) 0x00AA00AA;
+	addr[0x2AAA] = (FPW) 0x00550055;
+	addr[0x5555] = (FPW) 0x00900090;
+
+	mb ();
+	value = addr[0];
+
+	switch (value) {
+	case (FPW) INTEL_MANUFACT:
+		info->flash_id = FLASH_MAN_INTEL;
+		break;
+	default:
+		info->flash_id = FLASH_UNKNOWN;
+		info->sector_count = 0;
+		info->size = 0;
+		addr[0] = (FPW) 0x00FF00FF;	/* restore read mode */
+		return (0);			/* no or unknown flash	*/
+	}
+
+	mb ();
+	value = addr[1];			/* device ID	    */
+	switch (value) {
+	case (FPW) INTEL_ID_28F128J3A:
+		info->flash_id += FLASH_28F128J3A;
+		info->sector_count = 128;
+		info->size = 0x01000000;
+		break;				/* => 16 MB	*/
+	case (FPW) INTEL_ID_28F640J3A:
+		info->flash_id += FLASH_28F640J3A;
+		info->sector_count = 64;
+		info->size = 0x00800000;
+		break;				/* => 8 MB     */
+	default:
+		info->flash_id = FLASH_UNKNOWN;
+		break;
+	}
+
+	if (info->sector_count > CFG_MAX_FLASH_SECT) {
+		printf ("** ERROR: sector count %d > max (%d) **\n",
+			info->sector_count, CFG_MAX_FLASH_SECT);
+		info->sector_count = CFG_MAX_FLASH_SECT;
+	}
+
+	addr[0] = (FPW) 0x00FF00FF;	/* restore read mode */
+
+	return (info->size);
+}
+
+
+/*-----------------------------------------------------------------------
+ */
+
+int flash_erase (flash_info_t * info, int s_first, int s_last)
+{
+	int flag, prot, sect;
+	ulong type, start, last;
+	int rcode = 0;
+
+	if ((s_first < 0) || (s_first > s_last)) {
+		if (info->flash_id == FLASH_UNKNOWN) {
+			printf ("- missing\n");
+		} else {
+			printf ("- no sectors to erase\n");
+		}
+		return 1;
+	}
+
+	type = (info->flash_id & FLASH_VENDMASK);
+	if ((type != FLASH_MAN_INTEL)) {
+		printf ("Can't erase unknown flash type %08lx - aborted\n",
+			info->flash_id);
+		return 1;
+	}
+
+	prot = 0;
+	for (sect = s_first; sect <= s_last; ++sect) {
+		if (info->protect[sect]) {
+			prot++;
+		}
+	}
+
+	if (prot) {
+		printf ("- Warning: %d protected sectors will not be erased!\n",
+			prot);
+	} else {
+		printf ("\n");
+	}
+
+	/*start = get_timer (0); */
+	last = start;
+
+	/* Disable interrupts which might cause a timeout here */
+	flag = disable_interrupts ();
+
+	/* Start erase on unprotected sectors */
+	for (sect = s_first; sect <= s_last; sect++) {
+		if (info->protect[sect] == 0) { /* not protected */
+			FPWV *addr = (FPWV *) (info->start[sect]);
+			FPW status;
+
+			printf ("Erasing sector %2d ... ", sect);
+
+			/* arm simple, non interrupt dependent timer */
+			reset_timer_masked ();
+
+			*addr = (FPW) 0x00500050;	/* clear status register */
+			*addr = (FPW) 0x00200020;	/* erase setup */
+			*addr = (FPW) 0x00D000D0;	/* erase confirm */
+
+			while (((status = *addr) & (FPW) 0x00800080) != (FPW) 0x00800080) {
+				if (get_timer_masked () > CFG_FLASH_ERASE_TOUT) {
+					printf ("Timeout\n");
+					*addr = (FPW) 0x00B000B0;	/* suspend erase     */
+					*addr = (FPW) 0x00FF00FF;	/* reset to read mode */
+					rcode = 1;
+					break;
+				}
+			}
+
+			*addr = (FPW) 0x00500050;	/* clear status register cmd.	*/
+			*addr = (FPW) 0x00FF00FF;	/* resest to read mode		*/
+
+			printf (" done\n");
+		}
+	}
+	return rcode;
+}
+
+/*-----------------------------------------------------------------------
+ * Copy memory to flash, returns:
+ * 0 - OK
+ * 1 - write timeout
+ * 2 - Flash not erased
+ * 4 - Flash not identified
+ */
+
+int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt)
+{
+	ulong cp, wp;
+	FPW data;
+	int count, i, l, rc, port_width;
+
+	if (info->flash_id == FLASH_UNKNOWN) {
+		return 4;
+	}
+/* get lower word aligned address */
+#ifdef FLASH_PORT_WIDTH16
+	wp = (addr & ~1);
+	port_width = 2;
+#else
+	wp = (addr & ~3);
+	port_width = 4;
+#endif
+
+	/*
+	 * handle unaligned start bytes
+	 */
+	if ((l = addr - wp) != 0) {
+		data = 0;
+		for (i = 0, cp = wp; i < l; ++i, ++cp) {
+			data = (data << 8) | (*(uchar *) cp);
+		}
+		for (; i < port_width && cnt > 0; ++i) {
+			data = (data << 8) | *src++;
+			--cnt;
+			++cp;
+		}
+		for (; cnt == 0 && i < port_width; ++i, ++cp) {
+			data = (data << 8) | (*(uchar *) cp);
+		}
+
+		if ((rc = write_data (info, wp, SWAP (data))) != 0) {
+			return (rc);
+		}
+		wp += port_width;
+	}
+
+	/*
+	 * handle word aligned part
+	 */
+	count = 0;
+	while (cnt >= port_width) {
+		data = 0;
+		for (i = 0; i < port_width; ++i) {
+			data = (data << 8) | *src++;
+		}
+		if ((rc = write_data (info, wp, SWAP (data))) != 0) {
+			return (rc);
+		}
+		wp += port_width;
+		cnt -= port_width;
+		if (count++ > 0x800) {
+			spin_wheel ();
+			count = 0;
+		}
+	}
+
+	if (cnt == 0) {
+		return (0);
+	}
+
+	/*
+	 * handle unaligned tail bytes
+	 */
+	data = 0;
+	for (i = 0, cp = wp; i < port_width && cnt > 0; ++i, ++cp) {
+		data = (data << 8) | *src++;
+		--cnt;
+	}
+	for (; i < port_width; ++i, ++cp) {
+		data = (data << 8) | (*(uchar *) cp);
+	}
+
+	return (write_data (info, wp, SWAP (data)));
+}
+
+/*-----------------------------------------------------------------------
+ * Write a word or halfword to Flash, returns:
+ * 0 - OK
+ * 1 - write timeout
+ * 2 - Flash not erased
+ */
+static int write_data (flash_info_t * info, ulong dest, FPW data)
+{
+	FPWV *addr = (FPWV *) dest;
+	ulong status;
+	int flag;
+
+	/* Check if Flash is (sufficiently) erased */
+	if ((*addr & data) != data) {
+		printf ("not erased at %08lx (%x)\n", (ulong) addr, *addr);
+		return (2);
+	}
+	/* Disable interrupts which might cause a timeout here */
+	flag = disable_interrupts ();
+
+	*addr = (FPW) 0x00400040;	/* write setup */
+	*addr = data;
+
+	/* arm simple, non interrupt dependent timer */
+	reset_timer_masked ();
+
+	/* wait while polling the status register */
+	while (((status = *addr) & (FPW) 0x00800080) != (FPW) 0x00800080) {
+
+		if (get_timer_masked () > CFG_FLASH_WRITE_TOUT) {
+			*addr = (FPW) 0x00FF00FF;	/* restore read mode */
+			return (1);
+		}
+	}
+
+	*addr = (FPW) 0x00FF00FF;	/* restore read mode */
+
+	return (0);
+}
+
+void inline spin_wheel (void)
+{
+	static int p = 0;
+	static char w[] = "\\/-";
+
+	printf ("\010%c", w[p]);
+	(++p == 3) ? (p = 0) : 0;
+}
--- a/board/sx1/platform.S
+++ b/board/sx1/platform.S
@@ -0,0 +1,406 @@
+/*
+ * Board specific setup info
+ *
+ * (C) Copyright 2003
+ * Texas Instruments, <www.ti.com>
+ *
+ * -- Some bits of code used from rrload's head_OMAP1510.s --
+ * Copyright (C) 2002 RidgeRun, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <version.h>
+
+#if defined(CONFIG_OMAP1510)
+#include <./configs/omap1510.h>
+#endif
+
+#define OMAP1510_CLKS ((1<<EN_XORPCK)|(1<<EN_PERCK)|(1<<EN_TIMCK)|(1<<EN_GPIOCK))
+
+
+_TEXT_BASE:
+	.word	TEXT_BASE	 /* sdram load addr from config.mk */
+
+.globl platformsetup
+platformsetup:
+
+	/*
+	 * Configure 1510 pins functions to match our board.
+	 */
+	ldr	r0, REG_PULL_DWN_CTRL_0
+	ldr	r1, VAL_PULL_DWN_CTRL_0
+	str	r1, [r0]
+	ldr	r0, REG_PULL_DWN_CTRL_1
+	ldr	r1, VAL_PULL_DWN_CTRL_1
+	str	r1, [r0]
+	ldr	r0, REG_PULL_DWN_CTRL_2
+	ldr	r1, VAL_PULL_DWN_CTRL_2
+	str	r1, [r0]
+	ldr	r0, REG_PULL_DWN_CTRL_3
+	ldr	r1, VAL_PULL_DWN_CTRL_3
+	str	r1, [r0]
+	ldr	r0, REG_FUNC_MUX_CTRL_4
+	ldr	r1, VAL_FUNC_MUX_CTRL_4
+	str	r1, [r0]
+	ldr	r0, REG_FUNC_MUX_CTRL_5
+	ldr	r1, VAL_FUNC_MUX_CTRL_5
+	str	r1, [r0]
+	ldr	r0, REG_FUNC_MUX_CTRL_6
+	ldr	r1, VAL_FUNC_MUX_CTRL_6
+	str	r1, [r0]
+	ldr	r0, REG_FUNC_MUX_CTRL_7
+	ldr	r1, VAL_FUNC_MUX_CTRL_7
+	str	r1, [r0]
+	ldr	r0, REG_FUNC_MUX_CTRL_8
+	ldr	r1, VAL_FUNC_MUX_CTRL_8
+	str	r1, [r0]
+	ldr	r0, REG_FUNC_MUX_CTRL_9
+	ldr	r1, VAL_FUNC_MUX_CTRL_9
+	str	r1, [r0]
+	ldr	r0, REG_FUNC_MUX_CTRL_A
+	ldr	r1, VAL_FUNC_MUX_CTRL_A
+	str	r1, [r0]
+	ldr	r0, REG_FUNC_MUX_CTRL_B
+	ldr	r1, VAL_FUNC_MUX_CTRL_B
+	str	r1, [r0]
+	ldr	r0, REG_FUNC_MUX_CTRL_C
+	ldr	r1, VAL_FUNC_MUX_CTRL_C
+	str	r1, [r0]
+	ldr	r0, REG_FUNC_MUX_CTRL_D
+	ldr	r1, VAL_FUNC_MUX_CTRL_D
+	str	r1, [r0]
+	ldr	r0, REG_VOLTAGE_CTRL_0
+	ldr	r1, VAL_VOLTAGE_CTRL_0
+	str	r1, [r0]
+	ldr	r0, REG_TEST_DBG_CTRL_0
+	ldr	r1, VAL_TEST_DBG_CTRL_0
+	str	r1, [r0]
+	ldr	r0, REG_MOD_CONF_CTRL_0
+	ldr	r1, VAL_MOD_CONF_CTRL_0
+	str	r1, [r0]
+
+	/* Move to 1510 mode */
+	ldr	r0, REG_COMP_MODE_CTRL_0
+	ldr	r1, VAL_COMP_MODE_CTRL_0
+	str	r1, [r0]
+
+	/* Set up Traffic Ctlr*/
+	ldr r0, REG_TC_IMIF_PRIO
+	mov r1, #0x0
+	str r1, [r0]
+	ldr r0, REG_TC_EMIFS_PRIO
+	str r1, [r0]
+	ldr r0, REG_TC_EMIFF_PRIO
+	str r1, [r0]
+
+	ldr r0, REG_TC_EMIFS_CONFIG
+	ldr r1, [r0]
+	bic r1, r1, #0x08   /* clear the global power-down enable PDE bit */
+	bic r1, r1, #0x01   /* write protect flash by clearing the WP bit */
+	str r1, [r0]	    /* EMIFS GlB Configuration. (value 0x12 most likely) */
+
+	ldr r0, _GPIO_PIN_CONTROL_REG
+	ldrh r1,[r0]
+	orr r1, r1, #0x0001 /* M_PCM_SYNC */
+	orr r1, r1, #0x4000 /* IPC_ACTIVE */
+	orr r1, r1, #0x0002 /* A_IRDA_OFF */
+	orr r1, r1, #0x0800 /* A_SWITCH	  */
+	orr r1, r1, #0x8000 /* A_USB_ON	  */
+	strh r1,[r0]
+
+	ldr r0, _GPIO_DIR_CONTROL_REG
+	ldrh r1,[r0]
+	bic r1, r1, #0x0001 /* M_PCM_SYNC */
+	bic r1, r1, #0x4000 /* IPC_ACTIVE */
+	bic r1, r1, #0x0002 /* A_IRDA_OFF */
+	bic r1, r1, #0x0800 /* A_SWITCH	  */
+	bic r1, r1, #0x8000 /* A_USB_ON	  */
+	strh r1,[r0]
+
+	ldr r0, _GPIO_DATA_OUTPUT_REG
+	ldrh r1,[r0]
+	bic r1, r1, #0x0001 /* M_PCM_SYNC */
+	orr r1, r1, #0x4000 /* IPC_ACTIVE */
+	orr r1, r1, #0x0002 /* A_IRDA_OFF */
+	bic r1, r1, #0x0800 /* A_SWITCH	  */
+	bic r1, r1, #0x8000 /* A_USB_ON	  */
+	strh r1,[r0]
+
+	/* Setup some clock domains */
+	ldr r1, =OMAP1510_CLKS
+	ldr r0, REG_ARM_IDLECT2
+	strh r1, [r0]  /* CLKM, Clock domain control. */
+
+	mov r1, #0x01  /* PER_EN bit */
+	ldr r0, REG_ARM_RSTCT2
+	strh r1, [r0]  /* CLKM; Peripheral reset. */
+
+	/* Set CLKM to Sync-Scalable  */
+	/* I supposidly need to enable the dsp clock before switching */
+	mov r1, #0x1000
+	ldr r0, REG_ARM_SYSST
+	strh r1, [r0]
+	mov r0, #0x400
+1:
+	subs r0, r0, #0x1   /* wait for any bubbles to finish */
+	bne 1b
+
+	ldr r1, VAL_ARM_CKCTL  /* use 12Mhz ref, PER must be <= 50Mhz so /2 */
+	ldr r0, REG_ARM_CKCTL
+	strh r1, [r0]
+
+	/* setup DPLL 1 */
+	ldr r1, VAL_DPLL1_CTL
+	ldr r0, REG_DPLL1_CTL
+	strh r1, [r0]
+	ands r1, r1, #0x10  /* Check if PLL is enabled. */
+	beq lock_end	    /* Do not look for lock if BYPASS selected */
+2:
+	ldrh r1, [r0]
+	ands r1, r1, #0x01  /* Check the LOCK bit. */
+	beq 2b		    /* ...loop until bit goes hi. */
+lock_end:
+
+	/* Set memory timings corresponding to the new clock speed */
+
+	/* Check execution location to determine current execution location
+	 * and branch to appropriate initialization code.
+	 */
+	mov r0, #0x10000000		    /* Load physical SDRAM base. */
+	mov r1, pc			    /* Get current execution location. */
+	cmp r1, r0			    /* Compare. */
+	bge skip_sdram			    /* Skip over EMIF-fast initialization if running from SDRAM. */
+
+	/*
+	 * Delay for SDRAM initialization.
+	 */
+	mov r3, #0x1800			       /* value should be checked */
+3:
+	subs r3, r3, #0x1		      /* Decrement count */
+	bne 3b
+
+	/*
+	 * Set SDRAM control values. Disable refresh before MRS command.
+	 */
+	ldr r0, VAL_TC_EMIFF_SDRAM_CONFIG   /* get good value */
+	bic r3, r0, #0xC		    /* (BIT3|BIT2) ulConfig with auto-refresh disabled. */
+	orr r3, r3, #0x8000000		    /* (BIT27) Disable CLK when Power down or Self-Refresh */
+	orr r3, r3, #0x4000000		    /* BIT26 Power Down Enable */
+	ldr r2, REG_TC_EMIFF_SDRAM_CONFIG   /* Point to configuration register. */
+	str r3, [r2]			    /* Store the passed value with AR disabled. */
+
+	ldr r1, VAL_TC_EMIFF_MRS	    /* get MRS value */
+	ldr r2, REG_TC_EMIFF_MRS	    /* Point to MRS register. */
+	str r1, [r2]			    /* Store the passed value.*/
+
+	ldr r2, REG_TC_EMIFF_SDRAM_CONFIG   /* Point to configuration register. */
+	str r0, [r2]			    /* Store the passed value. */
+
+	/*
+	 * Delay for SDRAM initialization.
+	 */
+	mov r3, #0x1800
+4:
+	subs r3, r3, #1			    /* Decrement count. */
+	bne 4b
+
+skip_sdram:
+
+	/* slow interface */
+	ldr r1, VAL_TC_EMIFS_CS0_CONFIG
+	ldr r0, REG_TC_EMIFS_CS0_CONFIG
+	str r1, [r0] /* Chip Select 0 */
+	ldr r1, VAL_TC_EMIFS_CS1_CONFIG
+	ldr r0, REG_TC_EMIFS_CS1_CONFIG
+	str r1, [r0] /* Chip Select 1 */
+	ldr r1, VAL_TC_EMIFS_CS2_CONFIG
+	ldr r0, REG_TC_EMIFS_CS2_CONFIG
+	str r1, [r0] /* Chip Select 2 */
+	ldr r1, VAL_TC_EMIFS_CS3_CONFIG
+	ldr r0, REG_TC_EMIFS_CS3_CONFIG
+	str r1, [r0] /* Chip Select 3 */
+
+	/* back to arch calling code */
+	mov	pc, lr
+
+/* the literal pools origin */
+	.ltorg
+
+/* OMAP configuration registers */
+REG_FUNC_MUX_CTRL_0:		/* 32 bits */
+	.word 0xfffe1000
+REG_FUNC_MUX_CTRL_1:		/* 32 bits */
+	.word 0xfffe1004
+REG_FUNC_MUX_CTRL_2:		/* 32 bits */
+	.word 0xfffe1008
+REG_COMP_MODE_CTRL_0:		/* 32 bits */
+	.word 0xfffe100c
+REG_FUNC_MUX_CTRL_3:		/* 32 bits */
+	.word 0xfffe1010
+REG_FUNC_MUX_CTRL_4:		/* 32 bits */
+	.word 0xfffe1014
+REG_FUNC_MUX_CTRL_5:		/* 32 bits */
+	.word 0xfffe1018
+REG_FUNC_MUX_CTRL_6:		/* 32 bits */
+	.word 0xfffe101c
+REG_FUNC_MUX_CTRL_7:		/* 32 bits */
+	.word 0xfffe1020
+REG_FUNC_MUX_CTRL_8:		/* 32 bits */
+	.word 0xfffe1024
+REG_FUNC_MUX_CTRL_9:		/* 32 bits */
+	.word 0xfffe1028
+REG_FUNC_MUX_CTRL_A:		/* 32 bits */
+	.word 0xfffe102C
+REG_FUNC_MUX_CTRL_B:		/* 32 bits */
+	.word 0xfffe1030
+REG_FUNC_MUX_CTRL_C:		/* 32 bits */
+	.word 0xfffe1034
+REG_FUNC_MUX_CTRL_D:		/* 32 bits */
+	.word 0xfffe1038
+REG_PULL_DWN_CTRL_0:		/* 32 bits */
+	.word 0xfffe1040
+REG_PULL_DWN_CTRL_1:		/* 32 bits */
+	.word 0xfffe1044
+REG_PULL_DWN_CTRL_2:		/* 32 bits */
+	.word 0xfffe1048
+REG_PULL_DWN_CTRL_3:		/* 32 bits */
+	.word 0xfffe104c
+REG_VOLTAGE_CTRL_0:		/* 32 bits */
+	.word 0xfffe1060
+REG_TEST_DBG_CTRL_0:		/* 32 bits */
+	.word 0xfffe1070
+REG_MOD_CONF_CTRL_0:		/* 32 bits */
+	.word 0xfffe1080
+REG_TC_IMIF_PRIO:		/* 32 bits */
+	.word 0xfffecc00
+REG_TC_EMIFS_PRIO:		/* 32 bits */
+	.word 0xfffecc04
+REG_TC_EMIFF_PRIO:		/* 32 bits */
+	.word 0xfffecc08
+REG_TC_EMIFS_CONFIG:		/* 32 bits */
+	.word 0xfffecc0c
+REG_TC_EMIFS_CS0_CONFIG:	/* 32 bits */
+	.word 0xfffecc10
+REG_TC_EMIFS_CS1_CONFIG:	/* 32 bits */
+	.word 0xfffecc14
+REG_TC_EMIFS_CS2_CONFIG:	/* 32 bits */
+	.word 0xfffecc18
+REG_TC_EMIFS_CS3_CONFIG:	/* 32 bits */
+	.word 0xfffecc1c
+REG_TC_EMIFF_SDRAM_CONFIG:	/* 32 bits */
+	.word 0xfffecc20
+REG_TC_EMIFF_MRS:		/* 32 bits */
+	.word 0xfffecc24
+/* MPU clock/reset/power mode control registers */
+REG_ARM_CKCTL:			/* 16 bits */
+	.word 0xfffece00
+REG_ARM_IDLECT2:		/* 16 bits */
+	.word 0xfffece08
+REG_ARM_RSTCT2:			/* 16 bits */
+	.word 0xfffece14
+REG_ARM_SYSST:			/* 16 bits */
+	.word 0xfffece18
+/* DPLL control registers */
+REG_DPLL1_CTL:			/* 16 bits */
+	.word 0xfffecf00
+/* identification code register */
+REG_IDCODE:			/* 32 bits */
+	.word 0xfffed404
+
+/* SX1 specific */
+_GPIO_PIN_CONTROL_REG:
+	.word GPIO_PIN_CONTROL_REG
+_GPIO_DIR_CONTROL_REG:
+	.word GPIO_DIR_CONTROL_REG
+_GPIO_DATA_OUTPUT_REG:
+	.word GPIO_DATA_OUTPUT_REG
+
+VAL_COMP_MODE_CTRL_0:
+	.word 0x0000eaef
+VAL_FUNC_MUX_CTRL_4:
+	.word 0x00000000
+VAL_FUNC_MUX_CTRL_5:
+	.word 0x00000000
+VAL_FUNC_MUX_CTRL_6:
+	.word 0x00000001
+VAL_FUNC_MUX_CTRL_7:
+	.word 0x00001000
+VAL_FUNC_MUX_CTRL_8:
+	.word 0x00001240       /*[Knoller]  Value of Symbian Image Wing B2*/
+VAL_FUNC_MUX_CTRL_9:
+	.word 0x00201008
+VAL_FUNC_MUX_CTRL_A:
+	.word 0x00001000
+VAL_FUNC_MUX_CTRL_B:
+	.word 0x00000000
+VAL_FUNC_MUX_CTRL_C:
+	.word 0x09008001       /*[Knoller]  Value of Symbian Image Wing B2*/
+VAL_FUNC_MUX_CTRL_D:
+	.word 0x00000000
+VAL_PULL_DWN_CTRL_0:
+	.word 0xfffeffff
+VAL_PULL_DWN_CTRL_1:
+	.word 0xd1ffffec
+VAL_PULL_DWN_CTRL_2:
+	.word 0xffa80c5b
+VAL_PULL_DWN_CTRL_3:
+	.word 0xffffc0fe
+VAL_VOLTAGE_CTRL_0:
+	.word 0x00000007
+VAL_TEST_DBG_CTRL_0:
+	/* The OMAP5910 TRM says this register must be 0, but HelenConfRegs
+	 * says to write a 7.  Don't know what the right thing is to do, so
+	 * I'm leaving it at 7 since that's what was already here.
+	 */
+	.word 0x00000007
+VAL_MOD_CONF_CTRL_0:
+	.word 0x0da20000       /*[Knoller]  Value of Symbian Image Wing B2*/
+
+VAL_ARM_CKCTL:
+	.word 0x010D
+
+VAL_DPLL1_CTL:
+	.word 0x3A33   /*[Hertle] Value of Symbian Image*/
+
+VAL_TC_EMIFS_CS1_CONFIG_PRELIM:
+	.word 0x00001149
+
+VAL_TC_EMIFS_CS2_CONFIG_PRELIM:
+	.word 0x00004158
+
+VAL_TC_EMIFS_CS0_CONFIG:
+	.word 0x00213090       /*[Knoller]  Value of Symbian Image Wing B2*/
+
+VAL_TC_EMIFS_CS1_CONFIG:
+	.word 0x00215070       /*[Knoller]  Value of Symbian Image Wing B2*/
+
+VAL_TC_EMIFS_CS2_CONFIG:
+	.word 0x00001139       /*[Knoller]  Value of Symbian Image Wing B2*/
+
+VAL_TC_EMIFS_CS3_CONFIG:
+	.word 0x00001139       /*[Knoller]  Value of Symbian Image Wing B2*/
+
+VAL_TC_EMIFF_SDRAM_CONFIG:
+	.word 0x0105f0b4       /*[Knoller]  Value of Symbian Image Wing B2*/
+
+
+VAL_TC_EMIFF_MRS:
+	.word 0x00000027       /*[Knoller]  Value of Symbian Image Wing B2*/
--- a/board/sx1/sx1.c
+++ b/board/sx1/sx1.c
@@ -0,0 +1,125 @@
+/*
+ * (C) Copyright 2004
+ * Wolfgang Denk, DENX Software Engineering, <wd@denx.de>
+ *
+ * (C) Copyright 2003
+ * Texas Instruments, <www.ti.com>
+ * Kshitij Gupta <Kshitij@ti.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+
+static void flash__init (void);
+static void ether__init (void);
+
+static inline void delay (unsigned long loops)
+{
+	__asm__ volatile ("1:\n"
+			  "subs %0, %1, #1\n"
+			  "bne 1b":"=r" (loops):"0" (loops));
+}
+
+/*
+ * Miscellaneous platform dependent initialisations
+ */
+
+int board_init (void)
+{
+	DECLARE_GLOBAL_DATA_PTR;
+
+	/* arch number of SX1 Board */
+	gd->bd->bi_arch_number = 241;
+
+	/* adress of boot parameters */
+	gd->bd->bi_boot_params = 0x10000100;
+
+/* kk - this speeds up your boot a quite a bit.	 However to make it
+ *  work, you need make sure your kernel startup flush bug is fixed.
+ *  ... rkw ...
+ */
+	icache_enable ();
+
+	flash__init ();
+	ether__init ();
+	return 0;
+}
+
+
+int misc_init_r (void)
+{
+	/* volatile ushort *gdir = (ushort *) (GPIO_DIR_CONTROL_REG); */
+	/* volatile ushort *mdir = (ushort *) (MPUIO_DIR_CONTROL_REG); */
+
+	/* setup gpio direction to match board (no floats!) */
+	/**gdir = 0xCFF9; */
+	/**mdir = 0x103F; */
+
+	return (0);
+}
+
+/******************************
+ Routine:
+ Description:
+******************************/
+static void flash__init (void)
+{
+#define CS0_CHIP_SELECT_REG 0xfffecc10
+#define CS3_CHIP_SELECT_REG 0xfffecc1c
+#define EMIFS_GlB_Config_REG 0xfffecc0c
+
+	unsigned int regval;
+
+	regval = *((volatile unsigned int *) EMIFS_GlB_Config_REG);
+	regval = regval | 0x0001;	/* Turn off write protection for flash devices. */
+	if (regval & 0x0002) {
+		regval = regval & 0xfffd;	/* Swap CS0 and CS3 so that flash is visible at 0x0 and eeprom at 0x0c000000. */
+		/* If, instead, you want to reference flash at 0x0c000000, then it seemed the following were necessary. */
+		/* *((volatile unsigned int *)CS0_CHIP_SELECT_REG) = 0x202090; / * Overrides head.S setting of 0x212090 */
+		/* *((volatile unsigned int *)CS3_CHIP_SELECT_REG) = 0x202090; / * Let's flash chips be fully functional. */
+	}
+	*((volatile unsigned int *) EMIFS_GlB_Config_REG) = regval;
+}
+
+
+/******************************
+ Routine:
+ Description:
+******************************/
+static void ether__init (void)
+{
+#define ETH_CONTROL_REG 0x0800000b
+	/* take the Ethernet controller out of reset and wait
+	 * for the EEPROM load to complete.
+	 */
+	*((volatile unsigned char *) ETH_CONTROL_REG) &= ~0x01;
+	udelay (3);
+}
+
+
+int dram_init (void)
+{
+	DECLARE_GLOBAL_DATA_PTR;
+
+	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
+
+	return 0;
+}
--- a/board/sx1/u-boot.lds
+++ b/board/sx1/u-boot.lds
@@ -0,0 +1,56 @@
+/*
+ * (C) Copyright 2004
+ * Wolfgang Denk, DENX Software Engineering, <wg@denx.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+/*OUTPUT_FORMAT("elf32-arm", "elf32-arm", "elf32-arm")*/
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+	. = 0x00000000;
+
+	. = ALIGN(4);
+	.text	   :
+	{
+	  cpu/arm925t/start.o	(.text)
+	  *(.text)
+	}
+
+	. = ALIGN(4);
+	.rodata : { *(.rodata) }
+
+	. = ALIGN(4);
+	.data : { *(.data) }
+
+	. = ALIGN(4);
+	.got : { *(.got) }
+
+	__u_boot_cmd_start = .;
+	.u_boot_cmd : { *(.u_boot_cmd) }
+	__u_boot_cmd_end = .;
+
+	. = ALIGN(4);
+	__bss_start = .;
+	.bss : { *(.bss) }
+	_end = .;
+}
--- a/board/tqm8xx/tqm8xx.c
+++ b/board/tqm8xx/tqm8xx.c
@@ -425,7 +425,7 @@ static long int dram_size (long int mamr_value, long int *base, long int maxsize

 #ifdef CONFIG_PS2MULT

-#ifdef CONFIG_BMS2003
+#ifdef CONFIG_HMI10
 #define BASE_BAUD ( 1843200 / 16 )
 struct serial_state rs_table[] = {
 	{ BASE_BAUD, 4,  (void*)0xec140000 },
@@ -441,12 +441,12 @@ int board_early_init_r (void)
 	return (0);
 }
 #endif
-#endif /* CONFIG_BMS2003 */
+#endif /* CONFIG_HMI10 */

 #endif /* CONFIG_PS2MULT */

 /* ------------------------------------------------------------------------- */
-#ifdef CONFIG_BMS2003
+#ifdef CONFIG_HMI10

 int misc_init_r (void)
 {
@@ -476,5 +476,5 @@ void ide_led (uchar led, uchar status)
 }
 #endif

-#endif /* CONFIG_BMS2003 */
+#endif /* CONFIG_HMI10 */
 /* ------------------------------------------------------------------------- */
--- a/board/trab/trab_fkt.c
+++ b/board/trab/trab_fkt.c
@@ -890,7 +890,7 @@ int do_touch (char **argv)
 	int     x, y;

 	if (strcmp (argv[2], "tl") == 0) {
-#if CONFIG_TOUCH_WAIT_PRESSED
+#ifdef CONFIG_TOUCH_WAIT_PRESSED
 		touch_wait_pressed();
 #else
 		{
@@ -915,7 +915,7 @@ int do_touch (char **argv)
 		return touch_write_clibration_values (CALIB_TL, x, y);
 	}
 	else if (strcmp (argv[2], "dr") == 0) {
-#if CONFIG_TOUCH_WAIT_PRESSED
+#ifdef CONFIG_TOUCH_WAIT_PRESSED
 		touch_wait_pressed();
 #else
 		{
--- a/Show More
+++ b/Show More
Author	SHA1	Message	Date
wdenk	42dfe7a184	Code cleanup; make several boards compile & link.	2004-03-14 22:25:36 +00:00
wdenk	855a496fe9	* Patches by Travis Sawyer, 12 Mar 2004: - Fix Gigabit Ethernet support for 440GX - Add Gigabit Ethernet Support to MII PHY utilities * Patch by Brad Kemp, 12 Mar 2004: Fixes for drivers/cfi_flash.c: - Better support for x8/x16 implementations - Added failure for AMD chips attempting to use CFG_FLASH_USE_BUFFER_WRITE - Added defines for AMD command and address constants * Patch by Leon Kukovec, 12 Mar 2004: Fix get_dentfromdir() to correctly handle deleted dentries * Patch by George G. Davis, 11 Mar 2004: Remove hard coded network settings in TI OMAP1610 H2 default board config * Patch by George G. Davis, 11 Mar 2004: add support for ADS GraphicsClient+ board.	2004-03-14 18:23:55 +00:00
wdenk	4b248f3f71	* Patch by Pierre Aubert, 11 Mar 2004: - add bitmap command and splash screen support in cfb console - add [optional] origin in the bitmap display command * Patch by Travis Sawyer, 11 Mar 2004: Fix ocotea board early init interrupt setup. * Patch by Thomas Viehweger, 11 Mar 2004: Remove redundand code; add PCI-specific bits to include/mpc8260.h	2004-03-14 16:51:43 +00:00
wdenk	aaf224ab4e	* Patch by Stephan Linz, 09 Mar 2004 - Add support for the SSV ADNP/ESC1 (Nios Softcore) * Patch by George G. Davis, 9 Mar 2004: fix recent build failure for SA1100 target * Patch by Travis Sawyer, 09 Mar 2004: Support native interrupt mode for the IBM440GX. Previously it was running in 440GP compatibility mode.	2004-03-14 15:20:55 +00:00
wdenk	3d3befa754	* Patch by Philippe Robin, 09 Mar 2004: Added ARM Integrator AP, CP and Versatile PB926EJ-S Reference Platform support. * Patch by Masami Komiya, 08 Mar 2004: Don't overwrite server IP address or boot file name when the boot server does not return values * Patch by listmember@orkun.us, 5 Mar 2004: Removed compile time restriction on CFG_I2C_SPEED for DS1338 RTC	2004-03-14 15:06:13 +00:00
wdenk	4d13cbad1c	* Patch by Tolunay Orkun, 5 Mar 2004: Fix early board initialization for Cogent CSB272 board * Patch by Ed Okerson, 3 Mar 2004: fix CFI flash writes for little endian systems * Patch by Reinhard Meyer, 01 Mar 2004: generalize USB and IDE support for MPC5200 with according changes to IceCube.h and TOP5200.h add Am29LV256 256 MBit FLASH support for TOP5200 boards add info about USB and IDE to README	2004-03-14 14:09:05 +00:00
wdenk	c3f9d4939a	* Patch by Yuli Barcohen, 4 Mar 2004: Fix problems with GCC 3.3.x which changed handling of global variables explicitly initialized to zero (now in .bss instead of .data as before). * Patch by Leon Kukovec, 02 Mar 2004: add strswab() to fix IDE LBA capacity, firmware and model numbers on little endian machines * Patch by Masami Komiya, 02 Mar 2004: - Remove get_ticks() from NFS code - Add verification of RPC transaction ID * Patch by Pierre Aubert, 02 Mar 2004: cleanup for IDE and USB drivers for MPC5200	2004-03-14 00:59:59 +00:00
wdenk	0e6d798cb3	* Patch by Travis Sawyer, 01 Mar 2004: Ocotea: - Add IBM PPC440GX Ref Platform support (Ocotea) Original code by Paul Reynolds <PaulReynolds@lhsolutions.com> Adapted to U-Boot and 440GX port 440gx_enet.c: - Add gracious handling of all Ethernet Pin Selections for 440GX - Add RGMII selection for Cicada CIS8201 Gigabit PHY ppc440.h: - Add needed bit definitions - Fix formatting * Patch by Carl Riechers, 1 Mar 2004: Add PPC440GX prbdv0 divider to fix memory clock calculation. * Patch by Stephan Linz, 27 Feb 2004 - avoid problems for targets without NFS download support	2004-03-14 00:07:33 +00:00
wdenk	c40b295682	* Patch by Rune Torgersen, 27 Feb 2004: - Added LBA48 support (CONFIG_LBA48 & CFG_64BIT_LBA) - Added support for 64bit printing in vsprintf (CFG_64BIT_VSPRINTF) - Added support for 64bit strtoul (CFG_64BIT_STRTOUL) * Patch by Masami Komiya, 27 Feb 2004: Fix rarpboot: add autoload by NFS * Patch by Dan Eisenhut, 26 Feb 2004: fix flash_write return value in saveenv * Patch by Stephan Linz, 11 Dec 2003 expand config.mk to avoid trigraph warnings on NIOS * Rename "BMS2003" board into "HMI10"	2004-03-13 23:29:43 +00:00
wdenk	6629d2f22b	SX1 patches: use "serial#" for USB serial #; use redundand environment storage; auto-set console on USB port (using preboot command)	2004-03-12 15:38:25 +00:00
wdenk	bdda519d3c	Cleanup.	2004-03-12 13:47:56 +00:00
wdenk	232c150a25	Add support for Siemens SX1 mobile phone; add support for USB-based console (enable with "setenv stdout usbtty; setenv stdin usbtty")	2004-03-12 00:14:09 +00:00
wdenk	79d696fc55	Fix LOWBOOT configuration for MPC5200 with DDR memory	2004-03-11 22:46:36 +00:00
wdenk	f8d813e34f	* Fix SDRAM timings for LITE5200 / IceCube board * Handle Auti-MDIX / connection status for INCA-IP * Fix USB problems when attempting to read 0 bytes	2004-03-02 14:05:39 +00:00
wdenk	e7c85689bb	* Patch by Travis Sawyer, 26 Feb 2004: Fix broken compile for XPEDITE1K target. * Patch by Stephan Linz, 26 Feb 2004: Bug fix for NFS code on NIOS targets * Patch by Stephen Williams, 26 Feb 2004: Break up SystemACE reads of large block counts	2004-02-27 08:21:54 +00:00
wdenk	132ba5fdc5	* Patch by Pierre Aubert, 26 Feb 2004 add IDE support for MPC5200 * Patch by Masami Komiya, 26 Feb 2004: add autoload via NFS * Patch by Stephen Williams Use of CONFIG_SERIAL_SOFTWARE_FIFO in board.c consistent with uses elsewhere in the source.	2004-02-27 08:20:54 +00:00
wdenk	11dadd547c	* Patch by Steven Scholz, 25 Feb 2004: - Timeouts in FPGA code should be based on CFG_HZ - Minor cleanup in code for Altera FPGA ACEX1K * Patch by Steven Scholz, 25 Feb 2004: Changed "Directory Hierarchy" section in README * Patch by Masami Komiya, 25 Feb 2004: Reduce copy count in nfs_read_reply() of NFS code	2004-02-27 00:07:27 +00:00
wdenk	80885a9d52	* Patch by Markus Pietrek, 24 Feb 2004: NS9750 DevBoard added * Patch by Pierre AUBERT, 24 Feb 2004 add USB support for MPC5200 * Patch by Steven Scholz, 24 Feb 2004: - fix MII commands to use values from last command * Patch by Torsten Demke, 24 Feb 2004: Add support for the eXalion platform (SPSW-8240, F-30, F-300)	2004-02-26 23:46:20 +00:00
wdenk	0c852a2886	* Patch by Rahul Shanbhag, 19 Feb 2004: Fixes for for OMAP1610 board: - shift some IRQ specific code to platform.S file - remove duplicatewatchdog reset code from start.S * Make Auto-MDIX Support configurable on INCA-IP board * Fix license for mkimage tool	2004-02-26 23:01:04 +00:00
wdenk	a084f7da88	* Patch by Masami Komiya, 24 Feb 2004: Update NetBootFileXferSize in NFS code * Patch by Scott McNutt, 24 Feb 2004: fix packet length in NFS code	2004-02-24 22:33:21 +00:00
wdenk	5cfbab3d82	Add missing board/dave/B2/B2.c file.	2004-02-24 02:01:43 +00:00
wdenk	cbd8a35c6d	* Patch by Masami Komiy, 22 Feb 2004: Add support for NFS for file download * Minor code cleanup	2004-02-24 02:00:03 +00:00
wdenk	074cff0d28	* Patch by Andrea Scian, 17 Feb 2004: Add support for S3C44B0 processor and DAVE B2 board * Patch by Steven Scholz, 20 Feb 2004: - Add support for MII commands on AT91RM9200 boards - some cleanup in AT91RM9200 ethernet code	2004-02-24 00:16:43 +00:00
wdenk	028ab6b598	* Patch by Peter Ryser, 20 Feb 2004: Add support for the Xilinx ML300 platform * Patch by Stephan Linz, 17 Feb 2004: Fix watchdog support for NIOS * Patch by Josh Fryman, 16 Feb 2004: Fix byte-swapping for cfi_flash.c for different bus widths * Patch by Jon Diekema, 14 Jeb 2004: Remove duplicate "FPGA Support" notes from the README file	2004-02-23 23:54:43 +00:00
wdenk	63e73c9a8e	* Patches by Reinhard Meyer, 14 Feb 2004: - update board/emk tree; use common flash driver - Corrected tested bits in machine check exception in cpu/mpc5xxx/traps.c [adapted for other PPC CPUs -- wd] - Added support for the M48T08 on the EVAL5200 board in rtc/mk48t59.c * Patch by Jon Diekema, 13 Feb 2004: Call show_boot_progress() whenever POST "FAILED" is printed. * Patch by Nishant Kamat, 13 Feb 2004: Add support for TI OMAP1610 H2 Board Fixes for cpu/arm926ejs/interrupt.c (based on Richard Woodruff's patch for arm925, 16 Oct 03) Fix for a timer bug in OMAP1610 Innovator Add support for CS0 (ROM)/CS3 (Flash) boot in OMAP1610 Innovator and H2 * Patches by Stephan Linz, 12 Feb 2004: - add support for NIOS timer with variable period preload counter value - prepare POST framework support for NIOS targets * Patch by Denis Peter, 11 Feb 2004: add POST support for the MIP405 board	2004-02-23 22:22:28 +00:00
wdenk	cd0a9de68b	* Patch by Laurent Mohin, 10 Feb 2004: Fix buffer overflow in common/usb.c * Patch by Tolunay Orkun, 10 Feb 2004: Add support for Cogent CSB272 board * Code cleanup	2004-02-23 20:48:38 +00:00
wdenk	2d1a537d87	* Patch by Thomas Elste, 10 Feb 2004: Add support for NET+50 CPU and ModNET50 board * Patch by Sam Song, 10 Feb 2004: Fix typos in cfi_flash.c * Patch by Leon Kukovec, 10 Feb 2004 Fixed long dir entry slot id calculation in get_vfatname * Patch by Robin Gilks, 10 Feb 2004: add "itest" command (operators: -eq, -ne, -lt, -gt, -le, -ge, ==, !=, <>, <, >, <=, >=)	2004-02-23 19:30:57 +00:00
wdenk	3f85ce2785	* CVS add missing files * Cleanup compiler warnings * Fix problem with side effects in macros in include/usb.h * Patch by David Benson, 13 Nov 2003: bug 841358 - fix TFTP download size limit * Fixing bug 850768: improper flush_cache() in load_serial() * Fixing bug 834943: MPC8540 - missing volatile declarations * Patch by Stephen Williams, 09 Feb 2004: Add support for Xilinx SystemACE chip: - New files common/cmd_ace.c and include/systemace.h - Hook systemace support into cmd_fat and the partition manager * Patch by Travis Sawyer, 09 Feb 2004: Add bi_opbfreq & bi_iic_fast to 440GX bd_info as needed for Linux	2004-02-23 16:11:30 +00:00
wdenk	3c74e32a98	* Patch by Travis Sawyer, 09 Feb 2004: o 440GX: - Fix PCI Indirect access for type 1 config cycles with ppc440. - Add phymode for 440 enet - fix pci pre init o XPedite1K: - Change board_pre_init to board_early_init_f - Add user flash to bus controller setup - Fix pci pre init - Fix is_pci_host to check GPIO for monarch bit - Force xpedite1k to pci conventional mode (via #define option) * Patch by Brad Kemp, 4 Feb 2004: - handle the machine check that is generated during the PCI scans on 82xx processors. - define the registers used in the IMMR by the PCI subsystem. * Patch by Pierre Aubert, 03 Feb 2004: cpu/mpc5xxx/start.S: copy MBAR into SPR311 * Patch by Jeff Angielski, 03 Feb 2004: Fix copy & paste error in cpu/mpc8260/pci.c * Patch by Reinhard Meyer, 24 Jan 2004: Fix typo in cpu/mpc5xxx/pci_mpc5200.c	2004-02-22 23:46:08 +00:00
wdenk	cf56e11019	Add Auto-MDIX support for INCA-IP	2004-02-20 22:02:48 +00:00