Prepare v2016.01-rc1

Signed-off-by: Tom Rini <trini@konsulko.com>

Kconfig

@@ -114,6 +114,16 @@ config SPL
 	help
 	  If you want to build SPL as well as the normal image, say Y.
 
+config SPL_SYS_MALLOC_SIMPLE
+	bool
+	depends on SPL
+	prompt "Only use malloc_simple functions in the spl"
+	help
+	  Say Y here to only use the *_simple malloc functions from
+	  malloc_simple.c, rather then using the versions from dlmalloc.c
+	  this will make the SPL binary smaller at the cost of more heap
+	  usage as the *_simple malloc functions do not re-use free-ed mem.
+
 config SPL_STACK_R
 	depends on SPL
 	bool "Enable SDRAM location for SPL stack"
@@ -132,6 +142,26 @@ config SPL_STACK_R_ADDR
 	  Specify the address in SDRAM for the SPL stack. This will be set up
 	  before board_init_r() is called.
 
+config SPL_STACK_R_MALLOC_SIMPLE_LEN
+	depends on SPL_STACK_R && SPL_SYS_MALLOC_SIMPLE
+	hex "Size of malloc_simple heap after switching to DRAM SPL stack"
+	default 0x100000
+	help
+	  Specify the amount of the stack to use as memory pool for
+	  malloc_simple after switching the stack to DRAM. This may be set
+	  to give board_init_r() a larger heap then the initial heap in
+	  SRAM which is limited to SYS_MALLOC_F_LEN bytes.
+
+config SPL_SEPARATE_BSS
+	depends on SPL
+	bool "BSS section is in a different memory region from text"
+	help
+	  Some platforms need a large BSS region in SPL and can provide this
+	  because RAM is already set up. In this case BSS can be moved to RAM.
+	  This option should then be enabled so that the correct device tree
+	  location is used. Normally we put the device tree at the end of BSS
+	  but with this option enabled, it goes at _image_binary_end.
+
 config TPL
 	bool
 	depends on SPL && SUPPORT_TPL

MAINTAINERS

@@ -370,7 +370,7 @@ T:	git git://git.denx.de/u-boot-sh.git
 F:	arch/sh/
 
 SPARC
-M:	Daniel Hellstrom <daniel@gaisler.com>
+M:	Francois Retief <fgretief@spaceteq.co.za>
 S:	Maintained
 T:	git git://git.denx.de/u-boot-sparc.git
 F:	arch/sparc/

Makefile

@@ -1,7 +1,11 @@
-VERSION = 2015
-PATCHLEVEL = 10
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+VERSION = 2016
+PATCHLEVEL = 01
 SUBLEVEL =
-EXTRAVERSION =
+EXTRAVERSION = -rc1
 NAME =
 
 # *DOCUMENTATION*
@@ -605,6 +609,8 @@ KBUILD_CFLAGS += $(KCFLAGS)
 UBOOTINCLUDE    := \
 		-Iinclude \
 		$(if $(KBUILD_SRC), -I$(srctree)/include) \
+		$(if $(CONFIG_SYS_THUMB_BUILD), $(if $(CONFIG_HAS_THUMB2),, \
+			-I$(srctree)/arch/$(ARCH)/thumb1/include),) \
 		-I$(srctree)/arch/$(ARCH)/include \
 		-include $(srctree)/include/linux/kconfig.h
 
@@ -901,7 +907,7 @@ MKIMAGEFLAGS_u-boot.kwb = -n $(srctree)/$(CONFIG_SYS_KWD_CONFIG:"%"=%) \
 	-T kwbimage -a $(CONFIG_SYS_TEXT_BASE) -e $(CONFIG_SYS_TEXT_BASE)
 
 MKIMAGEFLAGS_u-boot-spl.kwb = -n $(srctree)/$(CONFIG_SYS_KWD_CONFIG:"%"=%) \
-	-T kwbimage -a $(CONFIG_SPL_TEXT_BASE) -e $(CONFIG_SPL_TEXT_BASE)
+	-T kwbimage -a $(CONFIG_SYS_TEXT_BASE) -e $(CONFIG_SYS_TEXT_BASE)
 
 MKIMAGEFLAGS_u-boot.pbl = -n $(srctree)/$(CONFIG_SYS_FSL_PBL_RCW:"%"=%) \
 		-R $(srctree)/$(CONFIG_SYS_FSL_PBL_PBI:"%"=%) -T pblimage
@@ -909,8 +915,18 @@ MKIMAGEFLAGS_u-boot.pbl = -n $(srctree)/$(CONFIG_SYS_FSL_PBL_RCW:"%"=%) \
 u-boot.img u-boot.kwb u-boot.pbl: u-boot.bin FORCE
 	$(call if_changed,mkimage)
 
-u-boot-spl.kwb: u-boot.img spl/u-boot-spl.bin FORCE
+# If the kwboot xmodem protocol is used, to boot U-Boot on the MVEBU
+# SoC's, the SPL U-Boot returns to the BootROM after it completes
+# the SDRAM setup. The BootROM expects no U-Boot header in the main
+# U-Boot image. So we need to combine SPL and u-boot.bin instead of
+# u-boot.img in this case.
+ifdef CONFIG_MVEBU_BOOTROM_UARTBOOT
+u-boot-spl.kwb: u-boot-dtb.bin spl/u-boot-spl.bin FORCE
 	$(call if_changed,mkimage)
+else
+u-boot-spl.kwb: u-boot-dtb.img spl/u-boot-spl.bin FORCE
+	$(call if_changed,mkimage)
+endif
 
 MKIMAGEFLAGS_u-boot-dtb.img = $(MKIMAGEFLAGS_u-boot.img)
 
@@ -1120,7 +1136,11 @@ spl/u-boot-spl.pbl: spl/u-boot-spl.bin FORCE
 	$(call if_changed,mkimage)
 
 ifeq ($(ARCH),arm)
+ifdef CONFIG_DM
+UBOOT_BINLOAD := u-boot-dtb.img
+else
 UBOOT_BINLOAD := u-boot.img
+endif
 else
 UBOOT_BINLOAD := u-boot.bin
 endif
@@ -1278,6 +1298,7 @@ define filechk_timestamp.h
 			LC_ALL=C $${DATE} -u -d "$${SOURCE_DATE}" +'#define U_BOOT_DATE "%b %d %C%y"'; \
 			LC_ALL=C $${DATE} -u -d "$${SOURCE_DATE}" +'#define U_BOOT_TIME "%T"'; \
 			LC_ALL=C $${DATE} -u -d "$${SOURCE_DATE}" +'#define U_BOOT_TZ "%z"'; \
+			LC_ALL=C $${DATE} -u -d "$${SOURCE_DATE}" +'#define U_BOOT_DMI_DATE "%m/%d/%Y"'; \
 		else \
 			return 42; \
 		fi; \
@@ -1285,6 +1306,7 @@ define filechk_timestamp.h
 		LC_ALL=C date +'#define U_BOOT_DATE "%b %d %C%y"'; \
 		LC_ALL=C date +'#define U_BOOT_TIME "%T"'; \
 		LC_ALL=C date +'#define U_BOOT_TZ "%z"'; \
+		LC_ALL=C date +'#define U_BOOT_DMI_DATE "%m/%d/%Y"'; \
 	fi)
 endef
 

README

@@ -796,18 +796,10 @@ The following options need to be configured:
 - vxWorks boot parameters:
 
 		bootvx constructs a valid bootline using the following
-		environments variables: bootfile, ipaddr, serverip, hostname.
+		environments variables: bootdev, bootfile, ipaddr, netmask,
+		serverip, gatewayip, hostname, othbootargs.
 		It loads the vxWorks image pointed bootfile.
 
-		CONFIG_SYS_VXWORKS_BOOT_DEVICE - The vxworks device name
-		CONFIG_SYS_VXWORKS_MAC_PTR - Ethernet 6 byte MA -address
-		CONFIG_SYS_VXWORKS_SERVERNAME - Name of the server
-		CONFIG_SYS_VXWORKS_BOOT_ADDR - Address of boot parameters
-
-		CONFIG_SYS_VXWORKS_ADD_PARAMS
-
-		Add it at the end of the bootline. E.g "u=username pw=secret"
-
 		Note: If a "bootargs" environment is defined, it will overwride
 		the defaults discussed just above.
 
@@ -1480,8 +1472,8 @@ The following options need to be configured:
 		CONFIG_TPM
 		Support TPM devices.
 
-		CONFIG_TPM_TIS_I2C
-		Support for i2c bus TPM devices. Only one device
+		CONFIG_TPM_TIS_INFINEON
+		Support for Infineon i2c bus TPM devices. Only one device
 		per system is supported at this time.
 
 			CONFIG_TPM_TIS_I2C_BURST_LIMITATION
@@ -2446,6 +2438,15 @@ CBFS (Coreboot Filesystem) support
 		  - CONFIG_SYS_I2C_IHS_CH3 activate hardware channel 3
 		  - CONFIG_SYS_I2C_IHS_SPEED_3 speed channel 3
 		  - CONFIG_SYS_I2C_IHS_SLAVE_3 slave addr channel 3
+		  - activate dual channel with CONFIG_SYS_I2C_IHS_DUAL
+		  - CONFIG_SYS_I2C_IHS_SPEED_0_1 speed channel 0_1
+		  - CONFIG_SYS_I2C_IHS_SLAVE_0_1 slave addr channel 0_1
+		  - CONFIG_SYS_I2C_IHS_SPEED_1_1 speed channel 1_1
+		  - CONFIG_SYS_I2C_IHS_SLAVE_1_1 slave addr channel 1_1
+		  - CONFIG_SYS_I2C_IHS_SPEED_2_1 speed channel 2_1
+		  - CONFIG_SYS_I2C_IHS_SLAVE_2_1 slave addr channel 2_1
+		  - CONFIG_SYS_I2C_IHS_SPEED_3_1 speed channel 3_1
+		  - CONFIG_SYS_I2C_IHS_SLAVE_3_1 slave addr channel 3_1
 
 		additional defines:
 
@@ -3502,6 +3503,10 @@ FIT uImage format:
 		without a fastmap.
 		default: 0
 
+		CONFIG_MTD_UBI_FM_DEBUG
+		Enable UBI fastmap debug
+		default: 0
+
 - UBIFS support
 		CONFIG_CMD_UBIFS
 
@@ -3572,6 +3577,9 @@ FIT uImage format:
 
 		CONFIG_SYS_SPL_MALLOC_START
 		Starting address of the malloc pool used in SPL.
+		When this option is set the full malloc is used in SPL and
+		it is set up by spl_init() and before that, the simple malloc()
+		can be used if CONFIG_SYS_MALLOC_F is defined.
 
 		CONFIG_SYS_SPL_MALLOC_SIZE
 		The size of the malloc pool used in SPL.
@@ -5458,10 +5466,10 @@ List of environment variables (most likely not complete):
 		  unset, then it will be made silent if the U-Boot console
 		  is silent.
 
-  tftpsrcport	- If this is set, the value is used for TFTP's
+  tftpsrcp	- If this is set, the value is used for TFTP's
 		  UDP source port.
 
-  tftpdstport	- If this is set, the value is used for TFTP's UDP
+  tftpdstp	- If this is set, the value is used for TFTP's UDP
 		  destination port instead of the Well Know Port 69.
 
   tftpblocksize - Block size to use for TFTP transfers; if not set,
@@ -5475,6 +5483,14 @@ List of environment variables (most likely not complete):
 		  faster in networks with high packet loss rates or
 		  with unreliable TFTP servers.
 
+  tftptimeoutcountmax	- maximum count of TFTP timeouts (no
+		  unit, minimum value = 0). Defines how many timeouts
+		  can happen during a single file transfer before that
+		  transfer is aborted. The default is 10, and 0 means
+		  'no timeouts allowed'. Increasing this value may help
+		  downloads succeed with high packet loss rates, or with
+		  unreliable TFTP servers or client hardware.
+
   vlan		- When set to a value < 4095 the traffic over
 		  Ethernet is encapsulated/received over 802.1q
 		  VLAN tagged frames.

arch/Kconfig

@@ -24,6 +24,7 @@ config ARM
 	select CREATE_ARCH_SYMLINK
 	select HAVE_PRIVATE_LIBGCC if !ARM64
 	select HAVE_GENERIC_BOARD
+	select SYS_GENERIC_BOARD
 	select SUPPORT_OF_CONTROL
 
 config AVR32
@@ -63,6 +64,10 @@ config NIOS2
 	bool "Nios II architecture"
 	select HAVE_GENERIC_BOARD
 	select SYS_GENERIC_BOARD
+	select SUPPORT_OF_CONTROL
+	select OF_CONTROL
+	select DM
+	select CPU
 
 config OPENRISC
 	bool "OpenRISC architecture"
@@ -71,6 +76,7 @@ config PPC
 	bool "PowerPC architecture"
 	select HAVE_PRIVATE_LIBGCC
 	select HAVE_GENERIC_BOARD
+	select SYS_GENERIC_BOARD
 	select SUPPORT_OF_CONTROL
 
 config SANDBOX

arch/arc/dts/Makefile

@@ -1,3 +1,7 @@
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
 dtb-$(CONFIG_TARGET_ARCANGEL4) +=  arcangel4.dtb
 dtb-$(CONFIG_TARGET_TB100) +=  abilis_tb100.dtb
 

arch/arc/include/asm/bitops.h

@@ -16,4 +16,9 @@
 #define hweight16(x) generic_hweight16(x)
 #define hweight8(x) generic_hweight8(x)
 
+#include <asm-generic/bitops/fls.h>
+#include <asm-generic/bitops/__fls.h>
+#include <asm-generic/bitops/fls64.h>
+#include <asm-generic/bitops/__ffs.h>
+
 #endif /* __ASM_ARC_BITOPS_H */

arch/arm/Kconfig

@@ -10,6 +10,9 @@ config ARM64
 config HAS_VBAR
         bool
 
+config HAS_THUMB2
+        bool
+
 config CPU_ARM720T
         bool
 
@@ -32,9 +35,11 @@ config CPU_ARM1176
 config CPU_V7
         bool
         select HAS_VBAR
+        select HAS_THUMB2
 
 config CPU_V7M
 	bool
+        select HAS_THUMB2
 
 config CPU_PXA
         bool
@@ -105,20 +110,14 @@ config KIRKWOOD
 	bool "Marvell Kirkwood"
 	select CPU_ARM926EJS
 
-config TARGET_DB_88F6820_GP
-	bool "Support DB-88F6820-GP"
-	select CPU_V7
-	select SUPPORT_SPL
-
-config TARGET_DB_MV784MP_GP
-	bool "Support db-mv784mp-gp"
-	select CPU_V7
-	select SUPPORT_SPL
-
-config TARGET_MAXBCM
-	bool "Support maxbcm"
+config ARCH_MVEBU
+	bool "Marvell MVEBU family (Armada XP/38x)"
 	select CPU_V7
 	select SUPPORT_SPL
+	select OF_CONTROL
+	select OF_SEPARATE
+	select DM
+	select DM_SERIAL
 
 config TARGET_DEVKIT3250
 	bool "Support devkit3250"
@@ -522,6 +521,8 @@ config ARCH_SUNXI
 	select DM_USB
 	select OF_CONTROL
 	select OF_SEPARATE
+	select SPL_STACK_R if !MACH_SUN9I
+	select SPL_SYS_MALLOC_SIMPLE if !MACH_SUN9I
 	select USB
 	select USB_STORAGE
 	select USB_KEYBOARD
@@ -547,13 +548,20 @@ config ARCH_ZYNQ
 	select CPU_V7
 	select SUPPORT_SPL
 	select OF_CONTROL
+	select SPL_OF_CONTROL
 	select DM
+	select SPL_DM
 	select DM_SPI
+	select DM_SERIAL
 	select DM_SPI_FLASH
+	select SPL_SEPARATE_BSS
 
 config ARCH_ZYNQMP
 	bool "Support Xilinx ZynqMP Platform"
 	select ARM64
+	select DM
+	select OF_CONTROL
+	select DM_SERIAL
 
 config TEGRA
 	bool "NVIDIA Tegra"
@@ -631,6 +639,14 @@ config TARGET_LS1021ATWR
 	select CPU_V7
 	select SUPPORT_SPL
 
+config TARGET_LS1043ARDB
+	bool "Support ls1043ardb"
+	select ARM64
+	select ARMV8_MULTIENTRY
+	select SUPPORT_SPL
+	help
+	  Support for Freescale LS1043ARDB platform.
+
 config TARGET_H2200
 	bool "Support h2200"
 	select CPU_PXA
@@ -684,6 +700,8 @@ source "arch/arm/mach-keystone/Kconfig"
 
 source "arch/arm/mach-kirkwood/Kconfig"
 
+source "arch/arm/mach-mvebu/Kconfig"
+
 source "arch/arm/cpu/armv7/mx7/Kconfig"
 
 source "arch/arm/cpu/armv7/mx6/Kconfig"
@@ -745,6 +763,7 @@ source "board/freescale/ls2085aqds/Kconfig"
 source "board/freescale/ls2085ardb/Kconfig"
 source "board/freescale/ls1021aqds/Kconfig"
 source "board/freescale/ls1021atwr/Kconfig"
+source "board/freescale/ls1043ardb/Kconfig"
 source "board/freescale/mx23evk/Kconfig"
 source "board/freescale/mx25pdk/Kconfig"
 source "board/freescale/mx28evk/Kconfig"

arch/arm/cpu/Makefile

@@ -1 +1,5 @@
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
 obj- += dummy.o

arch/arm/cpu/arm926ejs/Makefile

@@ -20,3 +20,14 @@ obj-$(CONFIG_MX25) += mx25/
 obj-$(CONFIG_MX27) += mx27/
 obj-$(if $(filter mxs,$(SOC)),y) += mxs/
 obj-$(if $(filter spear,$(SOC)),y) += spear/
+
+# some files can only build in ARM or THUMB2, not THUMB1
+
+ifdef CONFIG_SYS_THUMB_BUILD
+ifndef CONFIG_HAS_THUMB2
+
+CFLAGS_cpu.o := -marm
+CFLAGS_cache.o := -marm
+
+endif
+endif

arch/arm/cpu/arm926ejs/cache.c

@@ -82,4 +82,9 @@ void flush_dcache_all(void)
 /*
  * Stub implementations for l2 cache operations
  */
+
 __weak void l2_cache_disable(void) {}
+
+#if defined CONFIG_SYS_THUMB_BUILD
+__weak void invalidate_l2_cache(void) {}
+#endif

arch/arm/cpu/arm926ejs/mx25/generic.c

@@ -13,6 +13,7 @@
 #include <div64.h>
 #include <netdev.h>
 #include <asm/io.h>
+#include <asm/arch-imx/cpu.h>
 #include <asm/arch/imx-regs.h>
 #include <asm/arch/clock.h>
 

arch/arm/cpu/arm926ejs/mxs/clock.c

@@ -309,7 +309,7 @@ void mxs_set_ssp_busclock(unsigned int bus, uint32_t freq)
 		bus, tgtclk, freq);
 }
 
-void mxs_set_lcdclk(uint32_t freq)
+void mxs_set_lcdclk(uint32_t __maybe_unused lcd_base, uint32_t freq)
 {
 	struct mxs_clkctrl_regs *clkctrl_regs =
 		(struct mxs_clkctrl_regs *)MXS_CLKCTRL_BASE;

arch/arm/cpu/armv7/ls102xa/Makefile

@@ -9,6 +9,7 @@ obj-y	+= clock.o
 obj-y	+= timer.o
 obj-y	+= fsl_epu.o
 
+obj-$(CONFIG_SCSI_AHCI_PLAT) += ls102xa_sata.o
 obj-$(CONFIG_OF_LIBFDT) += fdt.o
 obj-$(CONFIG_SYS_HAS_SERDES) += fsl_ls1_serdes.o ls102xa_serdes.o
 obj-$(CONFIG_SPL) += spl.o

arch/arm/cpu/armv7/ls102xa/cpu.c

@@ -301,6 +301,7 @@ int arch_cpu_init(void)
 	void *epu_base = (void *)(CONFIG_SYS_DCSRBAR + EPU_BLOCK_OFFSET);
 	void *rcpm2_base =
 		(void *)(CONFIG_SYS_DCSRBAR + DCSR_RCPM2_BLOCK_OFFSET);
+	struct ccsr_scfg *scfg = (void *)CONFIG_SYS_FSL_SCFG_ADDR;
 	u32 state;
 
 	/*
@@ -328,6 +329,8 @@ int arch_cpu_init(void)
 	 */
 	fsl_epu_clean(epu_base);
 
+	setbits_be32(&scfg->snpcnfgcr, SCFG_SNPCNFGCR_SEC_RD_WR);
+
 	return 0;
 }
 

arch/arm/cpu/armv7/ls102xa/fdt.c

@@ -171,7 +171,7 @@ void ft_cpu_setup(void *blob, bd_t *bd)
 	do_fixup_by_compat_u32(blob, "fsl, ls1021a-flexcan",
 			       "clock-frequency", busclk / 2, 1);
 
-#ifdef CONFIG_QSPI_BOOT
+#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
 	off = fdt_node_offset_by_compat_reg(blob, FSL_IFC_COMPAT,
 					    CONFIG_SYS_IFC_ADDR);
 	fdt_set_node_status(blob, off, FDT_STATUS_DISABLED, 0);

arch/arm/cpu/armv7/ls102xa/ls102xa_sata.c

@@ -0,0 +1,42 @@
+/*
+ * Copyright 2015 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/immap_ls102xa.h>
+#include <ahci.h>
+#include <scsi.h>
+
+/* port register default value */
+#define AHCI_PORT_PHY_1_CFG	0xa003fffe
+#define AHCI_PORT_PHY_2_CFG	0x28183411
+#define AHCI_PORT_PHY_3_CFG	0x0e081004
+#define AHCI_PORT_PHY_4_CFG	0x00480811
+#define AHCI_PORT_PHY_5_CFG	0x192c96a4
+#define AHCI_PORT_TRANS_CFG	0x08000025
+
+#define SATA_ECC_REG_ADDR	0x20220520
+#define SATA_ECC_DISABLE	0x00020000
+
+int ls1021a_sata_init(void)
+{
+	struct ccsr_ahci __iomem *ccsr_ahci = (void *)AHCI_BASE_ADDR;
+
+#ifdef CONFIG_SYS_FSL_ERRATUM_A008407
+	out_le32((void *)SATA_ECC_REG_ADDR, SATA_ECC_DISABLE);
+#endif
+
+	out_le32(&ccsr_ahci->ppcfg, AHCI_PORT_PHY_1_CFG);
+	out_le32(&ccsr_ahci->pp2c, AHCI_PORT_PHY_2_CFG);
+	out_le32(&ccsr_ahci->pp3c, AHCI_PORT_PHY_3_CFG);
+	out_le32(&ccsr_ahci->pp4c, AHCI_PORT_PHY_4_CFG);
+	out_le32(&ccsr_ahci->pp5c, AHCI_PORT_PHY_5_CFG);
+	out_le32(&ccsr_ahci->ptc, AHCI_PORT_TRANS_CFG);
+
+	ahci_init((void __iomem *)AHCI_BASE_ADDR);
+	scsi_scan(0);
+
+	return 0;
+}

arch/arm/cpu/armv7/mx6/Kconfig

@@ -23,10 +23,12 @@ config MX6SL
 	bool
 
 config MX6SX
+	select ROM_UNIFIED_SECTIONS
 	bool
 
 config MX6UL
 	select SYS_L2CACHE_OFF
+	select ROM_UNIFIED_SECTIONS
 	bool
 
 choice

arch/arm/cpu/armv7/mx6/Makefile

@@ -9,5 +9,4 @@
 
 obj-y	:= soc.o clock.o
 obj-$(CONFIG_SPL_BUILD)	     += ddr.o
-obj-$(CONFIG_SECURE_BOOT)    += hab.o
 obj-$(CONFIG_MP)             += mp.o

arch/arm/cpu/armv7/mx6/clock.c

@@ -473,6 +473,251 @@ static u32 get_mmdc_ch0_clk(void)
 	}
 }
 
+#if defined(CONFIG_VIDEO_MXS)
+static int enable_pll_video(u32 pll_div, u32 pll_num, u32 pll_denom,
+			    u32 post_div)
+{
+	u32 reg = 0;
+	ulong start;
+
+	debug("pll5 div = %d, num = %d, denom = %d\n",
+	      pll_div, pll_num, pll_denom);
+
+	/* Power up PLL5 video */
+	writel(BM_ANADIG_PLL_VIDEO_POWERDOWN |
+	       BM_ANADIG_PLL_VIDEO_BYPASS |
+	       BM_ANADIG_PLL_VIDEO_DIV_SELECT |
+	       BM_ANADIG_PLL_VIDEO_POST_DIV_SELECT,
+	       &imx_ccm->analog_pll_video_clr);
+
+	/* Set div, num and denom */
+	switch (post_div) {
+	case 1:
+		writel(BF_ANADIG_PLL_VIDEO_DIV_SELECT(pll_div) |
+		       BF_ANADIG_PLL_VIDEO_POST_DIV_SELECT(0x2),
+		       &imx_ccm->analog_pll_video_set);
+		break;
+	case 2:
+		writel(BF_ANADIG_PLL_VIDEO_DIV_SELECT(pll_div) |
+		       BF_ANADIG_PLL_VIDEO_POST_DIV_SELECT(0x1),
+		       &imx_ccm->analog_pll_video_set);
+		break;
+	case 4:
+		writel(BF_ANADIG_PLL_VIDEO_DIV_SELECT(pll_div) |
+		       BF_ANADIG_PLL_VIDEO_POST_DIV_SELECT(0x0),
+		       &imx_ccm->analog_pll_video_set);
+		break;
+	default:
+		puts("Wrong test_div!\n");
+		return -EINVAL;
+	}
+
+	writel(BF_ANADIG_PLL_VIDEO_NUM_A(pll_num),
+	       &imx_ccm->analog_pll_video_num);
+	writel(BF_ANADIG_PLL_VIDEO_DENOM_B(pll_denom),
+	       &imx_ccm->analog_pll_video_denom);
+
+	/* Wait PLL5 lock */
+	start = get_timer(0);	/* Get current timestamp */
+
+	do {
+		reg = readl(&imx_ccm->analog_pll_video);
+		if (reg & BM_ANADIG_PLL_VIDEO_LOCK) {
+			/* Enable PLL out */
+			writel(BM_ANADIG_PLL_VIDEO_ENABLE,
+			       &imx_ccm->analog_pll_video_set);
+			return 0;
+		}
+	} while (get_timer(0) < (start + 10)); /* Wait 10ms */
+
+	puts("Lock PLL5 timeout\n");
+
+	return -ETIME;
+}
+
+/*
+ * 24M--> PLL_VIDEO -> LCDIFx_PRED -> LCDIFx_PODF -> LCD
+ *
+ * 'freq' using KHz as unit, see driver/video/mxsfb.c.
+ */
+void mxs_set_lcdclk(u32 base_addr, u32 freq)
+{
+	u32 reg = 0;
+	u32 hck = MXC_HCLK / 1000;
+	/* DIV_SELECT ranges from 27 to 54 */
+	u32 min = hck * 27;
+	u32 max = hck * 54;
+	u32 temp, best = 0;
+	u32 i, j, max_pred = 8, max_postd = 8, pred = 1, postd = 1;
+	u32 pll_div, pll_num, pll_denom, post_div = 1;
+
+	debug("mxs_set_lcdclk, freq = %dKHz\n", freq);
+
+	if ((!is_cpu_type(MXC_CPU_MX6SX)) && !is_cpu_type(MXC_CPU_MX6UL)) {
+		debug("This chip not support lcd!\n");
+		return;
+	}
+
+	if (base_addr == LCDIF1_BASE_ADDR) {
+		reg = readl(&imx_ccm->cscdr2);
+		/* Can't change clocks when clock not from pre-mux */
+		if ((reg & MXC_CCM_CSCDR2_LCDIF1_CLK_SEL_MASK) != 0)
+			return;
+	}
+
+	if (is_cpu_type(MXC_CPU_MX6SX)) {
+		reg = readl(&imx_ccm->cscdr2);
+		/* Can't change clocks when clock not from pre-mux */
+		if ((reg & MXC_CCM_CSCDR2_LCDIF2_CLK_SEL_MASK) != 0)
+			return;
+	}
+
+	temp = freq * max_pred * max_postd;
+	if (temp > max) {
+		puts("Please decrease freq, too large!\n");
+		return;
+	}
+	if (temp < min) {
+		/*
+		 * Register: PLL_VIDEO
+		 * Bit Field: POST_DIV_SELECT
+		 * 00 — Divide by 4.
+		 * 01 — Divide by 2.
+		 * 10 — Divide by 1.
+		 * 11 — Reserved
+		 * No need to check post_div(1)
+		 */
+		for (post_div = 2; post_div <= 4; post_div <<= 1) {
+			if ((temp * post_div) > min) {
+				freq *= post_div;
+				break;
+			}
+		}
+
+		if (post_div > 4) {
+			printf("Fail to set rate to %dkhz", freq);
+			return;
+		}
+	}
+
+	/* Choose the best pred and postd to match freq for lcd */
+	for (i = 1; i <= max_pred; i++) {
+		for (j = 1; j <= max_postd; j++) {
+			temp = freq * i * j;
+			if (temp > max || temp < min)
+				continue;
+			if (best == 0 || temp < best) {
+				best = temp;
+				pred = i;
+				postd = j;
+			}
+		}
+	}
+
+	if (best == 0) {
+		printf("Fail to set rate to %dKHz", freq);
+		return;
+	}
+
+	debug("best %d, pred = %d, postd = %d\n", best, pred, postd);
+
+	pll_div = best / hck;
+	pll_denom = 1000000;
+	pll_num = (best - hck * pll_div) * pll_denom / hck;
+
+	/*
+	 *                                  pll_num
+	 *             (24MHz * (pll_div + --------- ))
+	 *                                 pll_denom
+	 *freq KHz =  --------------------------------
+	 *             post_div * pred * postd * 1000
+	 */
+
+	if (base_addr == LCDIF1_BASE_ADDR) {
+		if (enable_pll_video(pll_div, pll_num, pll_denom, post_div))
+			return;
+
+		/* Select pre-lcd clock to PLL5 and set pre divider */
+		clrsetbits_le32(&imx_ccm->cscdr2,
+				MXC_CCM_CSCDR2_LCDIF1_PRED_SEL_MASK |
+				MXC_CCM_CSCDR2_LCDIF1_PRE_DIV_MASK,
+				(0x2 << MXC_CCM_CSCDR2_LCDIF1_PRED_SEL_OFFSET) |
+				((pred - 1) <<
+				 MXC_CCM_CSCDR2_LCDIF1_PRE_DIV_OFFSET));
+
+		/* Set the post divider */
+		clrsetbits_le32(&imx_ccm->cbcmr,
+				MXC_CCM_CBCMR_LCDIF1_PODF_MASK,
+				((postd - 1) <<
+				 MXC_CCM_CBCMR_LCDIF1_PODF_OFFSET));
+	} else if (is_cpu_type(MXC_CPU_MX6SX)) {
+		/* Setting LCDIF2 for i.MX6SX */
+		if (enable_pll_video(pll_div, pll_num, pll_denom, post_div))
+			return;
+
+		/* Select pre-lcd clock to PLL5 and set pre divider */
+		clrsetbits_le32(&imx_ccm->cscdr2,
+				MXC_CCM_CSCDR2_LCDIF2_PRED_SEL_MASK |
+				MXC_CCM_CSCDR2_LCDIF2_PRE_DIV_MASK,
+				(0x2 << MXC_CCM_CSCDR2_LCDIF2_PRED_SEL_OFFSET) |
+				((pred - 1) <<
+				 MXC_CCM_CSCDR2_LCDIF2_PRE_DIV_OFFSET));
+
+		/* Set the post divider */
+		clrsetbits_le32(&imx_ccm->cscmr1,
+				MXC_CCM_CSCMR1_LCDIF2_PODF_MASK,
+				((postd - 1) <<
+				 MXC_CCM_CSCMR1_LCDIF2_PODF_OFFSET));
+	}
+}
+
+int enable_lcdif_clock(u32 base_addr)
+{
+	u32 reg = 0;
+	u32 lcdif_clk_sel_mask, lcdif_ccgr3_mask;
+
+	if (is_cpu_type(MXC_CPU_MX6SX)) {
+		if ((base_addr == LCDIF1_BASE_ADDR) ||
+		    (base_addr == LCDIF2_BASE_ADDR)) {
+			puts("Wrong LCD interface!\n");
+			return -EINVAL;
+		}
+		/* Set to pre-mux clock at default */
+		lcdif_clk_sel_mask = (base_addr == LCDIF2_BASE_ADDR) ?
+			MXC_CCM_CSCDR2_LCDIF2_CLK_SEL_MASK :
+			MXC_CCM_CSCDR2_LCDIF1_CLK_SEL_MASK;
+		lcdif_ccgr3_mask = (base_addr == LCDIF2_BASE_ADDR) ?
+			(MXC_CCM_CCGR3_LCDIF2_PIX_MASK |
+			 MXC_CCM_CCGR3_DISP_AXI_MASK) :
+			(MXC_CCM_CCGR3_LCDIF1_PIX_MASK |
+			 MXC_CCM_CCGR3_DISP_AXI_MASK);
+	} else if (is_cpu_type(MXC_CPU_MX6UL)) {
+		if (base_addr != LCDIF1_BASE_ADDR) {
+			puts("Wrong LCD interface!\n");
+			return -EINVAL;
+		}
+		/* Set to pre-mux clock at default */
+		lcdif_clk_sel_mask = MXC_CCM_CSCDR2_LCDIF1_CLK_SEL_MASK;
+		lcdif_ccgr3_mask =  MXC_CCM_CCGR3_LCDIF1_PIX_MASK;
+	} else {
+		return 0;
+	}
+
+	reg = readl(&imx_ccm->cscdr2);
+	reg &= ~lcdif_clk_sel_mask;
+	writel(reg, &imx_ccm->cscdr2);
+
+	/* Enable the LCDIF pix clock */
+	reg = readl(&imx_ccm->CCGR3);
+	reg |= lcdif_ccgr3_mask;
+	writel(reg, &imx_ccm->CCGR3);
+
+	reg = readl(&imx_ccm->CCGR2);
+	reg |= MXC_CCM_CCGR2_LCD_MASK;
+	writel(reg, &imx_ccm->CCGR2);
+}
+#endif
+
 #ifdef CONFIG_FSL_QSPI
 /* qspi_num can be from 0 - 1 */
 void enable_qspi_clk(int qspi_num)

arch/arm/cpu/armv7/mx6/soc.c

@@ -15,6 +15,7 @@
 #include <asm/arch/sys_proto.h>
 #include <asm/imx-common/boot_mode.h>
 #include <asm/imx-common/dma.h>
+#include <asm/imx-common/hab.h>
 #include <stdbool.h>
 #include <asm/arch/mxc_hdmi.h>
 #include <asm/arch/crm_regs.h>
@@ -48,6 +49,13 @@ U_BOOT_DEVICE(imx6_thermal) = {
 };
 #endif
 
+#if defined(CONFIG_SECURE_BOOT)
+struct imx_sec_config_fuse_t const imx_sec_config_fuse = {
+	.bank = 0,
+	.word = 6,
+};
+#endif
+
 u32 get_nr_cpus(void)
 {
 	struct scu_regs *scu = (struct scu_regs *)SCU_BASE_ADDR;
@@ -392,6 +400,13 @@ const struct boot_mode soc_boot_modes[] = {
 	{NULL,		0},
 };
 
+void reset_misc(void)
+{
+#ifdef CONFIG_VIDEO_MXS
+	lcdif_power_down();
+#endif
+}
+
 void s_init(void)
 {
 	struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR;

arch/arm/cpu/armv7/mx7/Kconfig

@@ -2,9 +2,11 @@ if ARCH_MX7
 
 config MX7
 	bool
+	select ROM_UNIFIED_SECTIONS
 	default y
 
 config MX7D
+	select ROM_UNIFIED_SECTIONS
 	bool
 
 choice

arch/arm/cpu/armv7/mx7/Makefile

@@ -6,3 +6,7 @@
 #
 
 obj-y	:= soc.o clock.o clock_slice.o
+
+ifdef CONFIG_ARMV7_PSCI
+obj-y  += psci-mx7.o psci.o
+endif

arch/arm/cpu/armv7/mx7/psci-mx7.c

@@ -0,0 +1,69 @@
+#include <asm/io.h>
+#include <asm/psci.h>
+#include <asm/arch/imx-regs.h>
+#include <common.h>
+
+#define __secure __attribute__((section("._secure.text")))
+
+#define GPC_CPU_PGC_SW_PDN_REQ	0xfc
+#define GPC_CPU_PGC_SW_PUP_REQ	0xf0
+#define GPC_PGC_C1		0x840
+
+#define BM_CPU_PGC_SW_PDN_PUP_REQ_CORE1_A7	0x2
+
+/* below is for i.MX7D */
+#define SRC_GPR1_MX7D		0x074
+#define SRC_A7RCR0		0x004
+#define SRC_A7RCR1		0x008
+
+#define BP_SRC_A7RCR0_A7_CORE_RESET0	0
+#define BP_SRC_A7RCR1_A7_CORE1_ENABLE	1
+
+static inline void imx_gpcv2_set_m_core_pgc(bool enable, u32 offset)
+{
+	writel(enable, GPC_IPS_BASE_ADDR + offset);
+}
+
+__secure void imx_gpcv2_set_core1_power(bool pdn)
+{
+	u32 reg = pdn ? GPC_CPU_PGC_SW_PUP_REQ : GPC_CPU_PGC_SW_PDN_REQ;
+	u32 val;
+
+	imx_gpcv2_set_m_core_pgc(true, GPC_PGC_C1);
+
+	val = readl(GPC_IPS_BASE_ADDR + reg);
+	val |= BM_CPU_PGC_SW_PDN_PUP_REQ_CORE1_A7;
+	writel(val, GPC_IPS_BASE_ADDR + reg);
+
+	while ((readl(GPC_IPS_BASE_ADDR + reg) &
+	       BM_CPU_PGC_SW_PDN_PUP_REQ_CORE1_A7) != 0)
+		;
+
+	imx_gpcv2_set_m_core_pgc(false, GPC_PGC_C1);
+}
+
+__secure void imx_enable_cpu_ca7(int cpu, bool enable)
+{
+	u32 mask, val;
+
+	mask = 1 << (BP_SRC_A7RCR1_A7_CORE1_ENABLE + cpu - 1);
+	val = readl(SRC_BASE_ADDR + SRC_A7RCR1);
+	val = enable ? val | mask : val & ~mask;
+	writel(val, SRC_BASE_ADDR + SRC_A7RCR1);
+}
+
+__secure int imx_cpu_on(int fn, int cpu, int pc)
+{
+	writel(pc, SRC_BASE_ADDR + cpu * 8 + SRC_GPR1_MX7D);
+	imx_gpcv2_set_core1_power(true);
+	imx_enable_cpu_ca7(cpu, true);
+	return 0;
+}
+
+__secure int imx_cpu_off(int cpu)
+{
+	imx_enable_cpu_ca7(cpu, false);
+	imx_gpcv2_set_core1_power(false);
+	writel(0, SRC_BASE_ADDR + cpu * 8 + SRC_GPR1_MX7D + 4);
+	return 0;
+}

arch/arm/cpu/armv7/mx7/psci.S

@@ -0,0 +1,54 @@
+#include <config.h>
+#include <linux/linkage.h>
+
+#include <asm/armv7.h>
+#include <asm/arch-armv7/generictimer.h>
+#include <asm/psci.h>
+
+	.pushsection ._secure.text, "ax"
+
+	.arch_extension sec
+
+	@ r1 = target CPU
+	@ r2 = target PC
+
+.globl	psci_arch_init
+psci_arch_init:
+	mov	r6, lr
+
+	bl	psci_get_cpu_id
+	bl	psci_get_cpu_stack_top
+	mov	sp, r0
+
+	bx	r6
+
+	@ r1 = target CPU
+	@ r2 = target PC
+
+.globl psci_cpu_on
+psci_cpu_on:
+	push	{lr}
+
+	mov	r0, r1
+	bl	psci_get_cpu_stack_top
+	str	r2, [r0]
+	dsb
+
+	ldr	r2, =psci_cpu_entry
+	bl	imx_cpu_on
+
+	pop	{pc}
+
+.globl psci_cpu_off
+psci_cpu_off:
+
+	bl	psci_cpu_off_common
+	bl	psci_get_cpu_id
+	bl	imx_cpu_off
+
+1: 	wfi
+	b 1b
+
+	.globl psci_text_end
+psci_text_end:
+	.popsection

arch/arm/cpu/armv7/mx7/soc.c

@@ -11,6 +11,7 @@
 #include <asm/arch/sys_proto.h>
 #include <asm/imx-common/boot_mode.h>
 #include <asm/imx-common/dma.h>
+#include <asm/imx-common/hab.h>
 #include <asm/arch/crm_regs.h>
 #include <dm.h>
 #include <imx_thermal.h>
@@ -28,6 +29,13 @@ U_BOOT_DEVICE(imx7_thermal) = {
 };
 #endif
 
+#if defined(CONFIG_SECURE_BOOT)
+struct imx_sec_config_fuse_t const imx_sec_config_fuse = {
+	.bank = 1,
+	.word = 3,
+};
+#endif
+
 /*
  * OCOTP_TESTER3[9:8] (see Fusemap Description Table offset 0x440)
  * defines a 2-bit SPEED_GRADING
@@ -114,10 +122,19 @@ u32 __weak get_board_rev(void)
 }
 #endif
 
+/* enable all periherial can be accessed in nosec mode */
+static void init_csu(void)
+{
+	int i = 0;
+	for (i = 0; i < CSU_NUM_REGS; i++)
+		writel(CSU_INIT_SEC_LEVEL0, CSU_IPS_BASE_ADDR + i * 4);
+}
+
 int arch_cpu_init(void)
 {
 	init_aips();
 
+	init_csu();
 	/* Disable PDE bit of WMCR register */
 	imx_set_wdog_powerdown(false);
 

arch/arm/cpu/armv7/omap-common/utils.c

@@ -41,35 +41,73 @@ void cancel_out(u32 *num, u32 *den, u32 den_limit)
 	}
 }
 
-void __weak usb_fake_mac_from_die_id(u32 *id)
+__weak void omap_die_id(unsigned int *die_id)
 {
-	uint8_t device_mac[6];
+	die_id[0] = die_id[1] = die_id[2] = die_id[3] = 0;
+}
+
+void omap_die_id_serial(void)
+{
+	unsigned int die_id[4] = { 0 };
+	char serial_string[17] = { 0 };
+
+	omap_die_id((unsigned int *)&die_id);
+
+	if (!getenv("serial#")) {
+		snprintf(serial_string, sizeof(serial_string),
+			"%08x%08x", die_id[0], die_id[3]);
+
+		setenv("serial#", serial_string);
+	}
+}
+
+void omap_die_id_get_board_serial(struct tag_serialnr *serialnr)
+{
+	char *serial_string;
+	unsigned long long serial;
+
+	serial_string = getenv("serial#");
+
+	if (serial_string) {
+		serial = simple_strtoull(serial_string, NULL, 16);
+
+		serialnr->high = (unsigned int) (serial >> 32);
+		serialnr->low = (unsigned int) (serial & 0xffffffff);
+	} else {
+		serialnr->high = 0;
+		serialnr->low = 0;
+	}
+}
+
+void omap_die_id_usbethaddr(void)
+{
+	unsigned int die_id[4] = { 0 };
+	unsigned char mac[6] = { 0 };
+
+	omap_die_id((unsigned int *)&die_id);
 
 	if (!getenv("usbethaddr")) {
 		/*
-		 * create a fake MAC address from the processor ID code.
-		 * first byte is 0x02 to signify locally administered.
+		 * Create a fake MAC address from the processor ID code.
+		 * First byte is 0x02 to signify locally administered.
 		 */
-		device_mac[0] = 0x02;
-		device_mac[1] = id[3] & 0xff;
-		device_mac[2] = id[2] & 0xff;
-		device_mac[3] = id[1] & 0xff;
-		device_mac[4] = id[0] & 0xff;
-		device_mac[5] = (id[0] >> 8) & 0xff;
+		mac[0] = 0x02;
+		mac[1] = die_id[3] & 0xff;
+		mac[2] = die_id[2] & 0xff;
+		mac[3] = die_id[1] & 0xff;
+		mac[4] = die_id[0] & 0xff;
+		mac[5] = (die_id[0] >> 8) & 0xff;
 
-		eth_setenv_enetaddr("usbethaddr", device_mac);
+		eth_setenv_enetaddr("usbethaddr", mac);
 	}
 }
 
-void __weak usb_set_serial_num_from_die_id(u32 *id)
+void omap_die_id_display(void)
 {
-	char serialno[72];
-	uint32_t serialno_lo, serialno_hi;
+	unsigned int die_id[4] = { 0 };
 
-	if (!getenv("serial#")) {
-		serialno_hi = id[0];
-		serialno_lo = id[1];
-		sprintf(serialno, "%08x%08x", serialno_hi, serialno_lo);
-		setenv("serial#", serialno);
-	}
+	omap_die_id(die_id);
+
+	printf("OMAP die ID: %08x%08x%08x%08x", die_id[0], die_id[1], die_id[2],
+		die_id[3]);
 }

arch/arm/cpu/armv7/omap3/board.c

@@ -214,7 +214,7 @@ void board_init_f(ulong dummy)
  */
 int __weak misc_init_r(void)
 {
-	dieid_num_r();
+	omap_die_id_display();
 
 	return 0;
 }

arch/arm/cpu/armv7/omap3/sys_info.c

@@ -42,39 +42,14 @@ static char *rev_s_37xx[CPU_37XX_MAX_REV] = {
 				"1.2"};
 #endif /* CONFIG_DISPLAY_CPUINFO */
 
-/*****************************************************************
- * get_dieid(u32 *id) - read die ID
- *****************************************************************/
-void get_dieid(u32 *id)
+void omap_die_id(unsigned int *die_id)
 {
 	struct ctrl_id *id_base = (struct ctrl_id *)OMAP34XX_ID_L4_IO_BASE;
 
-	id[3] = readl(&id_base->die_id_0);
-	id[2] = readl(&id_base->die_id_1);
-	id[1] = readl(&id_base->die_id_2);
-	id[0] = readl(&id_base->die_id_3);
-}
-
-/*****************************************************************
- * dieid_num_r(void) - read and set die ID
- *****************************************************************/
-void dieid_num_r(void)
-{
-	char *uid_s, die_id[34];
-	u32 id[4];
-
-	memset(die_id, 0, sizeof(die_id));
-
-	uid_s = getenv("dieid#");
-
-	if (uid_s == NULL) {
-		get_dieid(id);
-		sprintf(die_id, "%08x%08x%08x%08x", id[0], id[1], id[2], id[3]);
-		setenv("dieid#", die_id);
-		uid_s = die_id;
-	}
-
-	printf("Die ID #%s\n", uid_s);
+	die_id[0] = readl(&id_base->die_id_0);
+	die_id[1] = readl(&id_base->die_id_1);
+	die_id[2] = readl(&id_base->die_id_2);
+	die_id[3] = readl(&id_base->die_id_3);
 }
 
 /******************************************

arch/arm/cpu/armv7/omap4/hwinit.c

@@ -156,6 +156,14 @@ void init_omap_revision(void)
 	}
 }
 
+void omap_die_id(unsigned int *die_id)
+{
+	die_id[0] = readl((*ctrl)->control_std_fuse_die_id_0);
+	die_id[1] = readl((*ctrl)->control_std_fuse_die_id_1);
+	die_id[2] = readl((*ctrl)->control_std_fuse_die_id_2);
+	die_id[3] = readl((*ctrl)->control_std_fuse_die_id_3);
+}
+
 #ifndef CONFIG_SYS_L2CACHE_OFF
 void v7_outer_cache_enable(void)
 {

arch/arm/cpu/armv7/omap4/prcm-regs.c

@@ -280,7 +280,10 @@ struct prcm_regs const omap4_prcm = {
 
 struct omap_sys_ctrl_regs const omap4_ctrl = {
 	.control_status				= 0x4A0022C4,
-	.control_id_code			= 0x4A002204,
+	.control_std_fuse_die_id_0		= 0x4A002200,
+	.control_std_fuse_die_id_1		= 0x4A002208,
+	.control_std_fuse_die_id_2		= 0x4A00220C,
+	.control_std_fuse_die_id_3		= 0x4A002210,
 	.control_std_fuse_opp_bgap		= 0x4a002260,
 	.control_status				= 0x4a0022c4,
 	.control_ldosram_iva_voltage_ctrl	= 0x4A002320,

arch/arm/cpu/armv7/omap5/hwinit.c

@@ -379,6 +379,14 @@ void init_omap_revision(void)
 	init_cpu_configuration();
 }
 
+void omap_die_id(unsigned int *die_id)
+{
+	die_id[0] = readl((*ctrl)->control_std_fuse_die_id_0);
+	die_id[1] = readl((*ctrl)->control_std_fuse_die_id_1);
+	die_id[2] = readl((*ctrl)->control_std_fuse_die_id_2);
+	die_id[3] = readl((*ctrl)->control_std_fuse_die_id_3);
+}
+
 void reset_cpu(ulong ignored)
 {
 	u32 omap_rev = omap_revision();

arch/arm/cpu/armv7/omap5/prcm-regs.c

@@ -298,6 +298,10 @@ struct prcm_regs const omap5_es1_prcm = {
 struct omap_sys_ctrl_regs const omap5_ctrl = {
 	.control_status				= 0x4A002134,
 	.control_std_fuse_opp_vdd_mpu_2		= 0x4A0021B4,
+	.control_std_fuse_die_id_0		= 0x4A002200,
+	.control_std_fuse_die_id_1		= 0x4A002208,
+	.control_std_fuse_die_id_2		= 0x4A00220C,
+	.control_std_fuse_die_id_3		= 0x4A002210,
 	.control_phy_power_usb 			= 0x4A002370,
 	.control_phy_power_sata			= 0x4A002374,
 	.control_padconf_core_base		= 0x4A002800,

arch/arm/cpu/armv7/s5p-common/cpu_info.c

@@ -5,9 +5,12 @@
  * SPDX-License-Identifier:	GPL-2.0+
  */
 #include <common.h>
+#include <fdtdec.h>
 #include <asm/io.h>
 #include <asm/arch/clk.h>
 
+DECLARE_GLOBAL_DATA_PTR;
+
 /* Default is s5pc100 */
 unsigned int s5p_cpu_id = 0xC100;
 /* Default is EVT1 */
@@ -30,7 +33,16 @@ u32 get_device_type(void)
 #ifdef CONFIG_DISPLAY_CPUINFO
 int print_cpuinfo(void)
 {
-	printf("CPU:   %s%X @ ", s5p_get_cpu_name(), s5p_cpu_id);
+	const char *cpu_model;
+	int len;
+
+	/* For SoC with no real CPU ID in naming convention. */
+	cpu_model = fdt_getprop(gd->fdt_blob, 0, "cpu-model", &len);
+	if (cpu_model)
+		printf("CPU:   %.*s @ ", len, cpu_model);
+	else
+		printf("CPU:   %s%X @ ", s5p_get_cpu_name(), s5p_cpu_id);
+
 	print_freq(get_arm_clk(), "\n");
 
 	return 0;

arch/arm/cpu/armv7/sunxi/board.c

@@ -136,7 +136,7 @@ DECLARE_GLOBAL_DATA_PTR;
  */
 u32 spl_boot_device(void)
 {
-	struct mmc *mmc0, *mmc1;
+	__maybe_unused struct mmc *mmc0, *mmc1;
 	/*
 	 * When booting from the SD card or NAND memory, the "eGON.BT0"
 	 * signature is expected to be found in memory at the address 0x0004
@@ -157,15 +157,18 @@ u32 spl_boot_device(void)
 		return BOOT_DEVICE_BOARD;
 
 	/* The BROM will try to boot from mmc0 first, so try that first. */
+#ifdef CONFIG_MMC
 	mmc_initialize(gd->bd);
 	mmc0 = find_mmc_device(0);
 	if (sunxi_mmc_has_egon_boot_signature(mmc0))
 		return BOOT_DEVICE_MMC1;
+#endif
 
 	/* Fallback to booting NAND if enabled. */
 	if (IS_ENABLED(CONFIG_SPL_NAND_SUPPORT))
 		return BOOT_DEVICE_NAND;
 
+#ifdef CONFIG_MMC
 	if (CONFIG_MMC_SUNXI_SLOT_EXTRA == 2) {
 		mmc1 = find_mmc_device(1);
 		if (sunxi_mmc_has_egon_boot_signature(mmc1)) {
@@ -179,6 +182,7 @@ u32 spl_boot_device(void)
 			return BOOT_DEVICE_MMC2;
 		}
 	}
+#endif
 
 	panic("Could not determine boot source\n");
 	return -1;		/* Never reached */
@@ -192,6 +196,7 @@ u32 spl_boot_mode(void)
 
 void board_init_f(ulong dummy)
 {
+	spl_init();
 	preloader_console_init();
 
 #ifdef CONFIG_SPL_I2C_SUPPORT

arch/arm/cpu/armv7/sunxi/cpu_info.c

@@ -10,7 +10,7 @@
 #include <asm/io.h>
 #include <asm/arch/cpu.h>
 #include <asm/arch/clock.h>
-#include <axp221.h>
+#include <axp_pmic.h>
 #include <errno.h>
 
 #ifdef CONFIG_MACH_SUN6I
@@ -82,7 +82,7 @@ int print_cpuinfo(void)
 int sunxi_get_sid(unsigned int *sid)
 {
 #ifdef CONFIG_AXP221_POWER
-	return axp221_get_sid(sid);
+	return axp_get_sid(sid);
 #elif defined SUNXI_SID_BASE
 	int i;
 

arch/arm/cpu/armv7/sunxi/usb_phy.c

@@ -17,15 +17,6 @@
 #include <asm/gpio.h>
 #include <asm/io.h>
 #include <errno.h>
-#ifdef CONFIG_AXP152_POWER
-#include <axp152.h>
-#endif
-#ifdef CONFIG_AXP209_POWER
-#include <axp209.h>
-#endif
-#ifdef CONFIG_AXP221_POWER
-#include <axp221.h>
-#endif
 
 #define SUNXI_USB_PMU_IRQ_ENABLE	0x800
 #ifdef CONFIG_MACH_SUN8I_A33

arch/arm/cpu/armv7m/stm32f4/flash.c

@@ -97,6 +97,9 @@ int flash_erase(flash_info_t *info, int first, int last)
 		while (readl(&STM32_FLASH->sr) & STM32_FLASH_SR_BSY)
 			;
 
+		/* clear old sector number before writing a new one */
+		clrbits_le32(&STM32_FLASH->cr, STM32_FLASH_CR_SNB_MASK);
+
 		if (bank == 0) {
 			setbits_le32(&STM32_FLASH->cr,
 				     (i << STM32_FLASH_CR_SNB_OFFSET));
@@ -114,9 +117,9 @@ int flash_erase(flash_info_t *info, int first, int last)
 			;
 
 		clrbits_le32(&STM32_FLASH->cr, STM32_FLASH_CR_SER);
-		stm32f4_flash_lock(1);
 	}
 
+	stm32f4_flash_lock(1);
 	return 0;
 }
 

arch/arm/cpu/armv8/Makefile

@@ -15,6 +15,6 @@ obj-y	+= cache.o
 obj-y	+= tlb.o
 obj-y	+= transition.o
 
-obj-$(CONFIG_FSL_LSCH3) += fsl-lsch3/
+obj-$(CONFIG_FSL_LAYERSCAPE) += fsl-layerscape/
 obj-$(CONFIG_ARCH_ZYNQMP) += zynqmp/
 obj-$(CONFIG_TARGET_HIKEY) += hisilicon/

arch/arm/cpu/armv8/cache_v8.c

@@ -32,7 +32,7 @@ inline void set_pgtable_table(u64 *page_table, u64 index, u64 *table_addr)
 }
 
 /* to activate the MMU we need to set up virtual memory */
-static void mmu_setup(void)
+__weak void mmu_setup(void)
 {
 	bd_t *bd = gd->bd;
 	u64 *page_table = (u64 *)gd->arch.tlb_addr, i, j;

arch/arm/cpu/armv8/fsl-layerscape/Makefile

@@ -0,0 +1,30 @@
+#
+# Copyright 2014-2015, Freescale Semiconductor
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y += cpu.o
+obj-y += lowlevel.o
+obj-y += soc.o
+obj-$(CONFIG_MP) += mp.o
+obj-$(CONFIG_OF_LIBFDT) += fdt.o
+obj-$(CONFIG_SPL) += spl.o
+
+ifneq ($(CONFIG_FSL_LSCH3),)
+obj-y += fsl_lsch3_speed.o
+obj-$(CONFIG_SYS_HAS_SERDES) += fsl_lsch3_serdes.o
+else
+ifneq ($(CONFIG_FSL_LSCH2),)
+obj-y += fsl_lsch2_speed.o
+obj-$(CONFIG_SYS_HAS_SERDES) += fsl_lsch2_serdes.o
+endif
+endif
+
+ifneq ($(CONFIG_LS2085A),)
+obj-$(CONFIG_SYS_HAS_SERDES) += ls2085a_serdes.o
+else
+ifneq ($(CONFIG_LS1043A),)
+obj-$(CONFIG_SYS_HAS_SERDES) += ls1043a_serdes.o
+endif
+endif

arch/arm/cpu/armv8/fsl-layerscape/README.lsch2

@@ -0,0 +1,10 @@
+#
+# Copyright 2015 Freescale Semiconductor
+#
+# SPDX-License-Identifier:      GPL-2.0+
+#
+
+Freescale LayerScape with Chassis Generation 2
+
+This architecture supports Freescale ARMv8 SoCs with Chassis generation 2,
+for example LS1043A.

arch/arm/cpu/armv8/fsl-layerscape/README.lsch3

@@ -1,5 +1,5 @@
 #
-# Copyright 2014 Freescale Semiconductor
+# Copyright 2014-2015 Freescale Semiconductor
 #
 # SPDX-License-Identifier:      GPL-2.0+
 #

arch/arm/cpu/armv8/fsl-layerscape/cpu.c

@@ -1,5 +1,5 @@
 /*
- * Copyright 2014 Freescale Semiconductor, Inc.
+ * Copyright 2014-2015 Freescale Semiconductor, Inc.
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */
@@ -10,34 +10,28 @@
 #include <asm/system.h>
 #include <asm/armv8/mmu.h>
 #include <asm/io.h>
-#include <asm/arch-fsl-lsch3/soc.h>
-#include <asm/arch-fsl-lsch3/immap_lsch3.h>
+#include <asm/arch/fsl_serdes.h>
+#include <asm/arch/soc.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/speed.h>
+#ifdef CONFIG_MP
+#include <asm/arch/mp.h>
+#endif
+#include <fm_eth.h>
 #include <fsl_debug_server.h>
 #include <fsl-mc/fsl_mc.h>
-#include <asm/arch/fsl_serdes.h>
 #ifdef CONFIG_FSL_ESDHC
 #include <fsl_esdhc.h>
 #endif
-#include "cpu.h"
-#include "mp.h"
-#include "speed.h"
 
 DECLARE_GLOBAL_DATA_PTR;
 
-static struct cpu_type cpu_type_list[] = {
-#ifdef CONFIG_LS2085A
-	CPU_TYPE_ENTRY(LS2085, LS2085, 8),
-	CPU_TYPE_ENTRY(LS2080, LS2080, 8),
-	CPU_TYPE_ENTRY(LS2045, LS2045, 4),
-#endif
-};
-
 void cpu_name(char *name)
 {
 	struct ccsr_gur __iomem *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR);
 	unsigned int i, svr, ver;
 
-	svr = in_le32(&gur->svr);
+	svr = gur_in32(&gur->svr);
 	ver = SVR_SOC_VER(svr);
 
 	for (i = 0; i < ARRAY_SIZE(cpu_type_list); i++)
@@ -54,146 +48,6 @@ void cpu_name(char *name)
 }
 
 #ifndef CONFIG_SYS_DCACHE_OFF
-
-#define SECTION_SHIFT_L0		39UL
-#define SECTION_SHIFT_L1		30UL
-#define SECTION_SHIFT_L2		21UL
-#define BLOCK_SIZE_L0			0x8000000000
-#define BLOCK_SIZE_L1			0x40000000
-#define BLOCK_SIZE_L2			0x200000
-
-#define NUM_OF_ENTRY		512
-
-#define TCR_EL2_PS_40BIT	(2 << 16)
-#define LSCH3_VA_BITS		(40)
-#define LSCH3_TCR	(TCR_TG0_4K		| \
-			TCR_EL2_PS_40BIT	| \
-			TCR_SHARED_NON		| \
-			TCR_ORGN_NC		| \
-			TCR_IRGN_NC		| \
-			TCR_T0SZ(LSCH3_VA_BITS))
-#define LSCH3_TCR_FINAL	(TCR_TG0_4K		| \
-			TCR_EL2_PS_40BIT	| \
-			TCR_SHARED_OUTER	| \
-			TCR_ORGN_WBWA		| \
-			TCR_IRGN_WBWA		| \
-			TCR_T0SZ(LSCH3_VA_BITS))
-
-#define CONFIG_SYS_FSL_CCSR_BASE	0x00000000
-#define CONFIG_SYS_FSL_CCSR_SIZE	0x10000000
-#define CONFIG_SYS_FSL_QSPI_BASE1	0x20000000
-#define CONFIG_SYS_FSL_QSPI_SIZE1	0x10000000
-#define CONFIG_SYS_FSL_IFC_BASE1	0x30000000
-#define CONFIG_SYS_FSL_IFC_SIZE1	0x10000000
-#define CONFIG_SYS_FSL_IFC_SIZE1_1	0x400000
-#define CONFIG_SYS_FSL_DRAM_BASE1	0x80000000
-#define CONFIG_SYS_FSL_DRAM_SIZE1	0x80000000
-#define CONFIG_SYS_FSL_QSPI_BASE2	0x400000000
-#define CONFIG_SYS_FSL_QSPI_SIZE2	0x100000000
-#define CONFIG_SYS_FSL_IFC_BASE2	0x500000000
-#define CONFIG_SYS_FSL_IFC_SIZE2	0x100000000
-#define CONFIG_SYS_FSL_DCSR_BASE	0x700000000
-#define CONFIG_SYS_FSL_DCSR_SIZE	0x40000000
-#define CONFIG_SYS_FSL_MC_BASE		0x80c000000
-#define CONFIG_SYS_FSL_MC_SIZE		0x4000000
-#define CONFIG_SYS_FSL_NI_BASE		0x810000000
-#define CONFIG_SYS_FSL_NI_SIZE		0x8000000
-#define CONFIG_SYS_FSL_QBMAN_BASE	0x818000000
-#define CONFIG_SYS_FSL_QBMAN_SIZE	0x8000000
-#define CONFIG_SYS_FSL_QBMAN_SIZE_1	0x4000000
-#define CONFIG_SYS_PCIE1_PHYS_SIZE	0x200000000
-#define CONFIG_SYS_PCIE2_PHYS_SIZE	0x200000000
-#define CONFIG_SYS_PCIE3_PHYS_SIZE	0x200000000
-#define CONFIG_SYS_PCIE4_PHYS_SIZE	0x200000000
-#define CONFIG_SYS_FSL_WRIOP1_BASE	0x4300000000
-#define CONFIG_SYS_FSL_WRIOP1_SIZE	0x100000000
-#define CONFIG_SYS_FSL_AIOP1_BASE	0x4b00000000
-#define CONFIG_SYS_FSL_AIOP1_SIZE	0x100000000
-#define CONFIG_SYS_FSL_PEBUF_BASE	0x4c00000000
-#define CONFIG_SYS_FSL_PEBUF_SIZE	0x400000000
-#define CONFIG_SYS_FSL_DRAM_BASE2	0x8080000000
-#define CONFIG_SYS_FSL_DRAM_SIZE2	0x7F80000000
-
-struct sys_mmu_table {
-	u64 virt_addr;
-	u64 phys_addr;
-	u64 size;
-	u64 memory_type;
-	u64 share;
-};
-
-static const struct sys_mmu_table lsch3_early_mmu_table[] = {
-	{ CONFIG_SYS_FSL_CCSR_BASE, CONFIG_SYS_FSL_CCSR_BASE,
-	  CONFIG_SYS_FSL_CCSR_SIZE, MT_DEVICE_NGNRNE, PMD_SECT_NON_SHARE },
-	{ CONFIG_SYS_FSL_OCRAM_BASE, CONFIG_SYS_FSL_OCRAM_BASE,
-	  CONFIG_SYS_FSL_OCRAM_SIZE, MT_NORMAL, PMD_SECT_NON_SHARE },
-	/* For IFC Region #1, only the first 4MB is cache-enabled */
-	{ CONFIG_SYS_FSL_IFC_BASE1, CONFIG_SYS_FSL_IFC_BASE1,
-	  CONFIG_SYS_FSL_IFC_SIZE1_1, MT_NORMAL, PMD_SECT_NON_SHARE },
-	{ CONFIG_SYS_FSL_IFC_BASE1 + CONFIG_SYS_FSL_IFC_SIZE1_1,
-	  CONFIG_SYS_FSL_IFC_BASE1 + CONFIG_SYS_FSL_IFC_SIZE1_1,
-	  CONFIG_SYS_FSL_IFC_SIZE1 - CONFIG_SYS_FSL_IFC_SIZE1_1,
-	  MT_DEVICE_NGNRNE, PMD_SECT_NON_SHARE },
-	{ CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FSL_IFC_BASE1,
-	  CONFIG_SYS_FSL_IFC_SIZE1, MT_DEVICE_NGNRNE, PMD_SECT_NON_SHARE },
-	{ CONFIG_SYS_FSL_DRAM_BASE1, CONFIG_SYS_FSL_DRAM_BASE1,
-	  CONFIG_SYS_FSL_DRAM_SIZE1, MT_NORMAL, PMD_SECT_OUTER_SHARE },
-	{ CONFIG_SYS_FSL_DCSR_BASE, CONFIG_SYS_FSL_DCSR_BASE,
-	  CONFIG_SYS_FSL_DCSR_SIZE, MT_DEVICE_NGNRNE, PMD_SECT_NON_SHARE },
-	{ CONFIG_SYS_FSL_DRAM_BASE2, CONFIG_SYS_FSL_DRAM_BASE2,
-	  CONFIG_SYS_FSL_DRAM_SIZE2, MT_NORMAL, PMD_SECT_OUTER_SHARE },
-};
-
-static const struct sys_mmu_table lsch3_final_mmu_table[] = {
-	{ CONFIG_SYS_FSL_CCSR_BASE, CONFIG_SYS_FSL_CCSR_BASE,
-	  CONFIG_SYS_FSL_CCSR_SIZE, MT_DEVICE_NGNRNE, PMD_SECT_NON_SHARE },
-	{ CONFIG_SYS_FSL_OCRAM_BASE, CONFIG_SYS_FSL_OCRAM_BASE,
-	  CONFIG_SYS_FSL_OCRAM_SIZE, MT_NORMAL, PMD_SECT_NON_SHARE },
-	{ CONFIG_SYS_FSL_DRAM_BASE1, CONFIG_SYS_FSL_DRAM_BASE1,
-	  CONFIG_SYS_FSL_DRAM_SIZE1, MT_NORMAL, PMD_SECT_OUTER_SHARE },
-	{ CONFIG_SYS_FSL_QSPI_BASE2, CONFIG_SYS_FSL_QSPI_BASE2,
-	  CONFIG_SYS_FSL_QSPI_SIZE2, MT_DEVICE_NGNRNE, PMD_SECT_NON_SHARE },
-	{ CONFIG_SYS_FSL_IFC_BASE2, CONFIG_SYS_FSL_IFC_BASE2,
-	  CONFIG_SYS_FSL_IFC_SIZE2, MT_DEVICE_NGNRNE, PMD_SECT_NON_SHARE },
-	{ CONFIG_SYS_FSL_DCSR_BASE, CONFIG_SYS_FSL_DCSR_BASE,
-	  CONFIG_SYS_FSL_DCSR_SIZE, MT_DEVICE_NGNRNE, PMD_SECT_NON_SHARE },
-	{ CONFIG_SYS_FSL_MC_BASE, CONFIG_SYS_FSL_MC_BASE,
-	  CONFIG_SYS_FSL_MC_SIZE, MT_DEVICE_NGNRNE, PMD_SECT_NON_SHARE },
-	{ CONFIG_SYS_FSL_NI_BASE, CONFIG_SYS_FSL_NI_BASE,
-	  CONFIG_SYS_FSL_NI_SIZE, MT_DEVICE_NGNRNE, PMD_SECT_NON_SHARE },
-	/* For QBMAN portal, only the first 64MB is cache-enabled */
-	{ CONFIG_SYS_FSL_QBMAN_BASE, CONFIG_SYS_FSL_QBMAN_BASE,
-	  CONFIG_SYS_FSL_QBMAN_SIZE_1, MT_NORMAL, PMD_SECT_NON_SHARE },
-	{ CONFIG_SYS_FSL_QBMAN_BASE + CONFIG_SYS_FSL_QBMAN_SIZE_1,
-	  CONFIG_SYS_FSL_QBMAN_BASE + CONFIG_SYS_FSL_QBMAN_SIZE_1,
-	  CONFIG_SYS_FSL_QBMAN_SIZE - CONFIG_SYS_FSL_QBMAN_SIZE_1,
-	  MT_DEVICE_NGNRNE, PMD_SECT_NON_SHARE },
-	{ CONFIG_SYS_PCIE1_PHYS_ADDR, CONFIG_SYS_PCIE1_PHYS_ADDR,
-	  CONFIG_SYS_PCIE1_PHYS_SIZE, MT_DEVICE_NGNRNE, PMD_SECT_NON_SHARE },
-	{ CONFIG_SYS_PCIE2_PHYS_ADDR, CONFIG_SYS_PCIE2_PHYS_ADDR,
-	  CONFIG_SYS_PCIE2_PHYS_SIZE, MT_DEVICE_NGNRNE, PMD_SECT_NON_SHARE },
-	{ CONFIG_SYS_PCIE3_PHYS_ADDR, CONFIG_SYS_PCIE3_PHYS_ADDR,
-	  CONFIG_SYS_PCIE3_PHYS_SIZE, MT_DEVICE_NGNRNE, PMD_SECT_NON_SHARE },
-#ifdef CONFIG_LS2085A
-	{ CONFIG_SYS_PCIE4_PHYS_ADDR, CONFIG_SYS_PCIE4_PHYS_ADDR,
-	  CONFIG_SYS_PCIE4_PHYS_SIZE, MT_DEVICE_NGNRNE, PMD_SECT_NON_SHARE },
-#endif
-	{ CONFIG_SYS_FSL_WRIOP1_BASE, CONFIG_SYS_FSL_WRIOP1_BASE,
-	  CONFIG_SYS_FSL_WRIOP1_SIZE, MT_DEVICE_NGNRNE, PMD_SECT_NON_SHARE },
-	{ CONFIG_SYS_FSL_AIOP1_BASE, CONFIG_SYS_FSL_AIOP1_BASE,
-	  CONFIG_SYS_FSL_AIOP1_SIZE, MT_DEVICE_NGNRNE, PMD_SECT_NON_SHARE },
-	{ CONFIG_SYS_FSL_PEBUF_BASE, CONFIG_SYS_FSL_PEBUF_BASE,
-	  CONFIG_SYS_FSL_PEBUF_SIZE, MT_DEVICE_NGNRNE, PMD_SECT_NON_SHARE },
-	{ CONFIG_SYS_FSL_DRAM_BASE2, CONFIG_SYS_FSL_DRAM_BASE2,
-	  CONFIG_SYS_FSL_DRAM_SIZE2, MT_NORMAL, PMD_SECT_OUTER_SHARE },
-};
-
-struct table_info {
-	u64 *ptr;
-	u64 table_base;
-	u64 entry_size;
-};
-
 /*
  * Set the block entries according to the information of the table.
  */
@@ -311,6 +165,7 @@ static inline void early_mmu_setup(void)
 	u64 *level1_table1 = (u64 *)(CONFIG_SYS_FSL_OCRAM_BASE + 0x2000);
 	u64 *level2_table0 = (u64 *)(CONFIG_SYS_FSL_OCRAM_BASE + 0x3000);
 	u64 *level2_table1 = (u64 *)(CONFIG_SYS_FSL_OCRAM_BASE + 0x4000);
+
 	struct table_info table = {level0_table, 0, BLOCK_SIZE_L0};
 
 	/* Invalidate all table entries */
@@ -320,19 +175,23 @@ static inline void early_mmu_setup(void)
 	set_pgtable_table(level0_table, 0, level1_table0);
 	set_pgtable_table(level0_table, 1, level1_table1);
 	set_pgtable_table(level1_table0, 0, level2_table0);
+
+#ifdef CONFIG_FSL_LSCH3
 	set_pgtable_table(level1_table0,
 			  CONFIG_SYS_FLASH_BASE >> SECTION_SHIFT_L1,
 			  level2_table1);
-
+#elif defined(CONFIG_FSL_LSCH2)
+	set_pgtable_table(level1_table0, 1, level2_table1);
+#endif
 	/* Find the table and fill in the block entries */
-	for (i = 0; i < ARRAY_SIZE(lsch3_early_mmu_table); i++) {
-		if (find_table(&lsch3_early_mmu_table[i],
+	for (i = 0; i < ARRAY_SIZE(early_mmu_table); i++) {
+		if (find_table(&early_mmu_table[i],
 			       &table, level0_table) == 0) {
 			/*
 			 * If find_table() returns error, it cannot be dealt
 			 * with here. Breakpoint can be added for debugging.
 			 */
-			set_block_entry(&lsch3_early_mmu_table[i], &table);
+			set_block_entry(&early_mmu_table[i], &table);
 			/*
 			 * If set_block_entry() returns error, it cannot be
 			 * dealt with here too.
@@ -341,7 +200,9 @@ static inline void early_mmu_setup(void)
 	}
 
 	el = current_el();
-	set_ttbr_tcr_mair(el, (u64)level0_table, LSCH3_TCR, MEMORY_ATTRIBUTES);
+
+	set_ttbr_tcr_mair(el, (u64)level0_table, LAYERSCAPE_TCR,
+			  MEMORY_ATTRIBUTES);
 	set_sctlr(get_sctlr() | CR_M);
 }
 
@@ -353,7 +214,12 @@ static inline void early_mmu_setup(void)
  * Level 1 table 0 contains 512 entries for each 1GB from 0 to 512GB.
  * Level 1 table 1 contains 512 entries for each 1GB from 512GB to 1TB.
  * Level 2 table 0 contains 512 entries for each 2MB from 0 to 1GB.
+ *
+ * For LSCH3:
  * Level 2 table 1 contains 512 entries for each 2MB from 32GB to 33GB.
+ * For LSCH2:
+ * Level 2 table 1 contains 512 entries for each 2MB from 1GB to 2GB.
+ * Level 2 table 2 contains 512 entries for each 2MB from 20GB to 21GB.
  */
 static inline void final_mmu_setup(void)
 {
@@ -362,7 +228,12 @@ static inline void final_mmu_setup(void)
 	u64 *level1_table0 = (u64 *)(gd->arch.tlb_addr + 0x1000);
 	u64 *level1_table1 = (u64 *)(gd->arch.tlb_addr + 0x2000);
 	u64 *level2_table0 = (u64 *)(gd->arch.tlb_addr + 0x3000);
+#ifdef CONFIG_FSL_LSCH3
 	u64 *level2_table1 = (u64 *)(gd->arch.tlb_addr + 0x4000);
+#elif defined(CONFIG_FSL_LSCH2)
+	u64 *level2_table1 = (u64 *)(gd->arch.tlb_addr + 0x4000);
+	u64 *level2_table2 = (u64 *)(gd->arch.tlb_addr + 0x5000);
+#endif
 	struct table_info table = {level0_table, 0, BLOCK_SIZE_L0};
 
 	/* Invalidate all table entries */
@@ -372,23 +243,30 @@ static inline void final_mmu_setup(void)
 	set_pgtable_table(level0_table, 0, level1_table0);
 	set_pgtable_table(level0_table, 1, level1_table1);
 	set_pgtable_table(level1_table0, 0, level2_table0);
+#ifdef CONFIG_FSL_LSCH3
 	set_pgtable_table(level1_table0,
 			  CONFIG_SYS_FSL_QBMAN_BASE >> SECTION_SHIFT_L1,
 			  level2_table1);
+#elif defined(CONFIG_FSL_LSCH2)
+	set_pgtable_table(level1_table0, 1, level2_table1);
+	set_pgtable_table(level1_table0,
+			  CONFIG_SYS_FSL_QBMAN_BASE >> SECTION_SHIFT_L1,
+			  level2_table2);
+#endif
 
 	/* Find the table and fill in the block entries */
-	for (i = 0; i < ARRAY_SIZE(lsch3_final_mmu_table); i++) {
-		if (find_table(&lsch3_final_mmu_table[i],
+	for (i = 0; i < ARRAY_SIZE(final_mmu_table); i++) {
+		if (find_table(&final_mmu_table[i],
 			       &table, level0_table) == 0) {
-			if (set_block_entry(&lsch3_final_mmu_table[i],
+			if (set_block_entry(&final_mmu_table[i],
 					    &table) != 0) {
 				printf("MMU error: could not set block entry for %p\n",
-				       &lsch3_final_mmu_table[i]);
+				       &final_mmu_table[i]);
 			}
 
 		} else {
 			printf("MMU error: could not find the table for %p\n",
-			       &lsch3_final_mmu_table[i]);
+			       &final_mmu_table[i]);
 		}
 	}
 
@@ -396,9 +274,13 @@ static inline void final_mmu_setup(void)
 	flush_dcache_range(gd->arch.tlb_addr,
 			   gd->arch.tlb_addr + gd->arch.tlb_size);
 
+#ifdef CONFIG_SYS_DPAA_FMAN
+	flush_dcache_all();
+#endif
 	/* point TTBR to the new table */
 	el = current_el();
-	set_ttbr_tcr_mair(el, (u64)level0_table, LSCH3_TCR_FINAL,
+
+	set_ttbr_tcr_mair(el, (u64)level0_table, LAYERSCAPE_TCR_FINAL,
 			  MEMORY_ATTRIBUTES);
 	/*
 	 * MMU is already enabled, just need to invalidate TLB to load the
@@ -434,8 +316,9 @@ static inline u32 initiator_type(u32 cluster, int init_id)
 {
 	struct ccsr_gur *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR);
 	u32 idx = (cluster >> (init_id * 8)) & TP_CLUSTER_INIT_MASK;
-	u32 type = in_le32(&gur->tp_ityp[idx]);
+	u32 type = 0;
 
+	type = gur_in32(&gur->tp_ityp[idx]);
 	if (type & TP_ITYP_AV)
 		return type;
 
@@ -450,7 +333,8 @@ u32 cpu_mask(void)
 
 	do {
 		int j;
-		cluster = in_le32(&gur->tp_cluster[i].lower);
+
+		cluster = gur_in32(&gur->tp_cluster[i].lower);
 		for (j = 0; j < TP_INIT_PER_CLUSTER; j++) {
 			type = initiator_type(cluster, j);
 			if (type) {
@@ -460,7 +344,7 @@ u32 cpu_mask(void)
 			}
 		}
 		i++;
-	} while ((cluster & TP_CLUSTER_EOC) != TP_CLUSTER_EOC);
+	} while ((cluster & TP_CLUSTER_EOC) == 0x0);
 
 	return mask;
 }
@@ -482,7 +366,8 @@ int fsl_qoriq_core_to_cluster(unsigned int core)
 
 	do {
 		int j;
-		cluster = in_le32(&gur->tp_cluster[i].lower);
+
+		cluster = gur_in32(&gur->tp_cluster[i].lower);
 		for (j = 0; j < TP_INIT_PER_CLUSTER; j++) {
 			if (initiator_type(cluster, j)) {
 				if (count == core)
@@ -491,7 +376,7 @@ int fsl_qoriq_core_to_cluster(unsigned int core)
 			}
 		}
 		i++;
-	} while ((cluster & TP_CLUSTER_EOC) != TP_CLUSTER_EOC);
+	} while ((cluster & TP_CLUSTER_EOC) == 0x0);
 
 	return -1;      /* cannot identify the cluster */
 }
@@ -505,7 +390,8 @@ u32 fsl_qoriq_core_to_type(unsigned int core)
 
 	do {
 		int j;
-		cluster = in_le32(&gur->tp_cluster[i].lower);
+
+		cluster = gur_in32(&gur->tp_cluster[i].lower);
 		for (j = 0; j < TP_INIT_PER_CLUSTER; j++) {
 			type = initiator_type(cluster, j);
 			if (type) {
@@ -515,7 +401,7 @@ u32 fsl_qoriq_core_to_type(unsigned int core)
 			}
 		}
 		i++;
-	} while ((cluster & TP_CLUSTER_EOC) != TP_CLUSTER_EOC);
+	} while ((cluster & TP_CLUSTER_EOC) == 0x0);
 
 	return -1;      /* cannot identify the cluster */
 }
@@ -527,15 +413,13 @@ int print_cpuinfo(void)
 	struct sys_info sysinfo;
 	char buf[32];
 	unsigned int i, core;
-	u32 type;
+	u32 type, rcw;
 
 	puts("SoC: ");
 
 	cpu_name(buf);
-	printf(" %s (0x%x)\n", buf, in_le32(&gur->svr));
-
+	printf(" %s (0x%x)\n", buf, gur_in32(&gur->svr));
 	memset((u8 *)buf, 0x00, ARRAY_SIZE(buf));
-
 	get_sys_info(&sysinfo);
 	puts("Clock Configuration:");
 	for_each_cpu(i, core, cpu_numcores(), cpu_mask()) {
@@ -551,18 +435,23 @@ int print_cpuinfo(void)
 	printf("\n       Bus:      %-4s MHz  ",
 	       strmhz(buf, sysinfo.freq_systembus));
 	printf("DDR:      %-4s MT/s", strmhz(buf, sysinfo.freq_ddrbus));
+#ifdef CONFIG_SYS_DPAA_FMAN
+	printf("  FMAN:     %-4s MHz", strmhz(buf, sysinfo.freq_fman[0]));
+#endif
+#ifdef CONFIG_FSL_LSCH3
 	printf("     DP-DDR:   %-4s MT/s", strmhz(buf, sysinfo.freq_ddrbus2));
+#endif
 	puts("\n");
 
-	/* Display the RCW, so that no one gets confused as to what RCW
+	/*
+	 * Display the RCW, so that no one gets confused as to what RCW
 	 * we're actually using for this boot.
 	 */
 	puts("Reset Configuration Word (RCW):");
 	for (i = 0; i < ARRAY_SIZE(gur->rcwsr); i++) {
-		u32 rcw = in_le32(&gur->rcwsr[i]);
-
+		rcw = gur_in32(&gur->rcwsr[i]);
 		if ((i % 4) == 0)
-			printf("\n       %02x:", i * 4);
+			printf("\n       %08x:", i * 4);
 		printf(" %08x", rcw);
 	}
 	puts("\n");
@@ -584,20 +473,28 @@ int cpu_eth_init(bd_t *bis)
 
 #ifdef CONFIG_FSL_MC_ENET
 	error = fsl_mc_ldpaa_init(bis);
+#endif
+#ifdef CONFIG_FMAN_ENET
+	fm_standard_init(bis);
 #endif
 	return error;
 }
 
 int arch_early_init_r(void)
 {
-	int rv;
-	rv = fsl_lsch3_wake_seconday_cores();
+#ifdef CONFIG_MP
+	int rv = 1;
 
+	rv = fsl_layerscape_wake_seconday_cores();
 	if (rv)
 		printf("Did not wake secondary cores\n");
+#endif
 
 #ifdef CONFIG_SYS_HAS_SERDES
 	fsl_serdes_init();
+#endif
+#ifdef CONFIG_FMAN_ENET
+	fman_enet_init();
 #endif
 	return 0;
 }
@@ -605,7 +502,9 @@ int arch_early_init_r(void)
 int timer_init(void)
 {
 	u32 __iomem *cntcr = (u32 *)CONFIG_SYS_FSL_TIMER_ADDR;
+#ifdef CONFIG_FSL_LSCH3
 	u32 __iomem *cltbenr = (u32 *)CONFIG_SYS_FSL_PMU_CLTBENR;
+#endif
 #ifdef COUNTER_FREQUENCY_REAL
 	unsigned long cntfrq = COUNTER_FREQUENCY_REAL;
 
@@ -613,10 +512,12 @@ int timer_init(void)
 	asm volatile("msr cntfrq_el0, %0" : : "r" (cntfrq) : "memory");
 #endif
 
+#ifdef CONFIG_FSL_LSCH3
 	/* Enable timebase for all clusters.
 	 * It is safe to do so even some clusters are not enabled.
 	 */
 	out_le32(cltbenr, 0xf);
+#endif
 
 	/* Enable clock for timer
 	 * This is a global setting.
@@ -632,7 +533,7 @@ void reset_cpu(ulong addr)
 	u32 val;
 
 	/* Raise RESET_REQ_B */
-	val = in_le32(rstcr);
+	val = scfg_in32(rstcr);
 	val |= 0x02;
-	out_le32(rstcr, val);
+	scfg_out32(rstcr, val);
 }

arch/arm/cpu/armv8/fsl-layerscape/cpu.h

@@ -1,5 +1,5 @@
 /*
- * Copyright 2014, Freescale Semiconductor
+ * Copyright 2014-2015, Freescale Semiconductor
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

arch/arm/cpu/armv8/fsl-layerscape/fdt.c

@@ -1,5 +1,5 @@
 /*
- * Copyright 2014 Freescale Semiconductor, Inc.
+ * Copyright 2014-2015 Freescale Semiconductor, Inc.
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */
@@ -7,11 +7,22 @@
 #include <common.h>
 #include <libfdt.h>
 #include <fdt_support.h>
-#include <asm/arch-fsl-lsch3/fdt.h>
+#include <phy.h>
+#ifdef CONFIG_FSL_LSCH3
+#include <asm/arch/fdt.h>
+#endif
 #ifdef CONFIG_FSL_ESDHC
 #include <fsl_esdhc.h>
 #endif
-#include "mp.h"
+#ifdef CONFIG_MP
+#include <asm/arch/mp.h>
+#endif
+
+int fdt_fixup_phy_connection(void *blob, int offset, phy_interface_t phyc)
+{
+	return fdt_setprop_string(blob, offset, "phy-connection-type",
+					 phy_string_for_interface(phyc));
+}
 
 #ifdef CONFIG_MP
 void ft_fixup_cpu(void *blob)
@@ -33,8 +44,8 @@ void ft_fixup_cpu(void *blob)
 	off = fdt_node_offset_by_prop_value(blob, -1, "device_type", "cpu", 4);
 	while (off != -FDT_ERR_NOTFOUND) {
 		reg = (fdt32_t *)fdt_getprop(blob, off, "reg", 0);
-		core_id = of_read_number(reg, addr_cells);
 		if (reg) {
+			core_id = of_read_number(reg, addr_cells);
 			if (core_id  == 0 || (is_core_online(core_id))) {
 				val = spin_tbl_addr;
 				val += id_to_core(core_id) *
@@ -150,6 +161,7 @@ void append_mmu_masters(void *blob, const char *smmu_path,
  *      for all DPAA2 devices.
  *
  */
+#ifdef CONFIG_FSL_LSCH3
 static void fdt_fixup_smmu(void *blob)
 {
 	int nodeoffset;
@@ -165,6 +177,7 @@ static void fdt_fixup_smmu(void *blob)
 	fdt_fixup_smmu_pcie(blob);
 #endif
 }
+#endif
 
 void ft_cpu_setup(void *blob, bd_t *bd)
 {
@@ -181,9 +194,11 @@ void ft_cpu_setup(void *blob, bd_t *bd)
 	ft_pci_setup(blob, bd);
 #endif
 
-#if defined(CONFIG_FSL_ESDHC)
+#ifdef CONFIG_FSL_ESDHC
 	fdt_fixup_esdhc(blob, bd);
 #endif
 
+#ifdef CONFIG_FSL_LSCH3
 	fdt_fixup_smmu(blob);
+#endif
 }

arch/arm/cpu/armv8/fsl-layerscape/fsl_lsch2_serdes.c

@@ -0,0 +1,117 @@
+/*
+ * Copyright 2015 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/errno.h>
+#include <asm/arch/fsl_serdes.h>
+#include <asm/arch/soc.h>
+
+#ifdef CONFIG_SYS_FSL_SRDS_1
+static u8 serdes1_prtcl_map[SERDES_PRCTL_COUNT];
+#endif
+
+int is_serdes_configured(enum srds_prtcl device)
+{
+	int ret = 0;
+
+#ifdef CONFIG_SYS_FSL_SRDS_1
+	ret |= serdes1_prtcl_map[device];
+#endif
+
+	return !!ret;
+}
+
+int serdes_get_first_lane(u32 sd, enum srds_prtcl device)
+{
+	struct ccsr_gur __iomem *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR);
+	u32 cfg = gur_in32(&gur->rcwsr[4]);
+	int i;
+
+	switch (sd) {
+#ifdef CONFIG_SYS_FSL_SRDS_1
+	case FSL_SRDS_1:
+		cfg &= FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_MASK;
+		cfg >>= FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_SHIFT;
+		break;
+#endif
+	default:
+		printf("invalid SerDes%d\n", sd);
+		break;
+	}
+
+	/* Is serdes enabled at all? */
+	if (unlikely(cfg == 0))
+		return -ENODEV;
+
+	for (i = 0; i < SRDS_MAX_LANES; i++) {
+		if (serdes_get_prtcl(sd, cfg, i) == device)
+			return i;
+	}
+
+	return -ENODEV;
+}
+
+int get_serdes_protocol(void)
+{
+	struct ccsr_gur __iomem *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR);
+	u32 cfg = gur_in32(&gur->rcwsr[4]) &
+			  FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_MASK;
+	cfg >>= FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_SHIFT;
+
+	return cfg;
+}
+
+const char *serdes_clock_to_string(u32 clock)
+{
+	switch (clock) {
+	case SRDS_PLLCR0_RFCK_SEL_100:
+		return "100";
+	case SRDS_PLLCR0_RFCK_SEL_125:
+		return "125";
+	case SRDS_PLLCR0_RFCK_SEL_156_25:
+		return "156.25";
+	default:
+		return "100";
+	}
+}
+
+void serdes_init(u32 sd, u32 sd_addr, u32 sd_prctl_mask, u32 sd_prctl_shift,
+		 u8 serdes_prtcl_map[SERDES_PRCTL_COUNT])
+{
+	struct ccsr_gur __iomem *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR);
+	u32 cfg;
+	int lane;
+
+	memset(serdes_prtcl_map, 0, sizeof(serdes_prtcl_map));
+
+	cfg = gur_in32(&gur->rcwsr[4]) & sd_prctl_mask;
+	cfg >>= sd_prctl_shift;
+	printf("Using SERDES%d Protocol: %d (0x%x)\n", sd + 1, cfg, cfg);
+
+	if (!is_serdes_prtcl_valid(sd, cfg))
+		printf("SERDES%d[PRTCL] = 0x%x is not valid\n", sd + 1, cfg);
+
+	for (lane = 0; lane < SRDS_MAX_LANES; lane++) {
+		enum srds_prtcl lane_prtcl = serdes_get_prtcl(sd, cfg, lane);
+
+		if (unlikely(lane_prtcl >= SERDES_PRCTL_COUNT))
+			debug("Unknown SerDes lane protocol %d\n", lane_prtcl);
+		else
+			serdes_prtcl_map[lane_prtcl] = 1;
+	}
+}
+
+void fsl_serdes_init(void)
+{
+#ifdef CONFIG_SYS_FSL_SRDS_1
+	serdes_init(FSL_SRDS_1,
+		    CONFIG_SYS_FSL_SERDES_ADDR,
+		    FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_MASK,
+		    FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_SHIFT,
+		    serdes1_prtcl_map);
+#endif
+}

arch/arm/cpu/armv8/fsl-layerscape/fsl_lsch2_speed.c

@@ -0,0 +1,180 @@
+/*
+ * Copyright 2015 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <linux/compiler.h>
+#include <asm/io.h>
+#include <asm/processor.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/soc.h>
+#include <fsl_ifc.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#ifndef CONFIG_SYS_FSL_NUM_CC_PLLS
+#define CONFIG_SYS_FSL_NUM_CC_PLLS      2
+#endif
+
+void get_sys_info(struct sys_info *sys_info)
+{
+	struct ccsr_gur __iomem *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR);
+#ifdef CONFIG_FSL_IFC
+	struct fsl_ifc ifc_regs = {(void *)CONFIG_SYS_IFC_ADDR, (void *)NULL};
+	u32 ccr;
+#endif
+#if defined(CONFIG_FSL_ESDHC) || defined(CONFIG_SYS_DPAA_FMAN)
+	u32 rcw_tmp;
+#endif
+	struct ccsr_clk *clk = (void *)(CONFIG_SYS_FSL_CLK_ADDR);
+	unsigned int cpu;
+	const u8 core_cplx_pll[8] = {
+		[0] = 0,	/* CC1 PPL / 1 */
+		[1] = 0,	/* CC1 PPL / 2 */
+		[4] = 1,	/* CC2 PPL / 1 */
+		[5] = 1,	/* CC2 PPL / 2 */
+	};
+
+	const u8 core_cplx_pll_div[8] = {
+		[0] = 1,	/* CC1 PPL / 1 */
+		[1] = 2,	/* CC1 PPL / 2 */
+		[4] = 1,	/* CC2 PPL / 1 */
+		[5] = 2,	/* CC2 PPL / 2 */
+	};
+
+	uint i;
+	uint freq_c_pll[CONFIG_SYS_FSL_NUM_CC_PLLS];
+	uint ratio[CONFIG_SYS_FSL_NUM_CC_PLLS];
+	unsigned long sysclk = CONFIG_SYS_CLK_FREQ;
+
+	sys_info->freq_systembus = sysclk;
+#ifdef CONFIG_DDR_CLK_FREQ
+	sys_info->freq_ddrbus = CONFIG_DDR_CLK_FREQ;
+#else
+	sys_info->freq_ddrbus = sysclk;
+#endif
+
+	sys_info->freq_systembus *= (gur_in32(&gur->rcwsr[0]) >>
+			FSL_CHASSIS2_RCWSR0_SYS_PLL_RAT_SHIFT) &
+			FSL_CHASSIS2_RCWSR0_SYS_PLL_RAT_MASK;
+	sys_info->freq_ddrbus *= (gur_in32(&gur->rcwsr[0]) >>
+			FSL_CHASSIS2_RCWSR0_MEM_PLL_RAT_SHIFT) &
+			FSL_CHASSIS2_RCWSR0_MEM_PLL_RAT_MASK;
+
+	for (i = 0; i < CONFIG_SYS_FSL_NUM_CC_PLLS; i++) {
+		ratio[i] = (in_be32(&clk->pllcgsr[i].pllcngsr) >> 1) & 0xff;
+		if (ratio[i] > 4)
+			freq_c_pll[i] = sysclk * ratio[i];
+		else
+			freq_c_pll[i] = sys_info->freq_systembus * ratio[i];
+	}
+
+	for (cpu = 0; cpu < CONFIG_MAX_CPUS; cpu++) {
+		u32 c_pll_sel = (in_be32(&clk->clkcsr[cpu].clkcncsr) >> 27)
+				& 0xf;
+		u32 cplx_pll = core_cplx_pll[c_pll_sel];
+
+		sys_info->freq_processor[cpu] =
+			freq_c_pll[cplx_pll] / core_cplx_pll_div[c_pll_sel];
+	}
+
+#define HWA_CGA_M1_CLK_SEL	0xe0000000
+#define HWA_CGA_M1_CLK_SHIFT	29
+#ifdef CONFIG_SYS_DPAA_FMAN
+	rcw_tmp = in_be32(&gur->rcwsr[7]);
+	switch ((rcw_tmp & HWA_CGA_M1_CLK_SEL) >> HWA_CGA_M1_CLK_SHIFT) {
+	case 2:
+		sys_info->freq_fman[0] = freq_c_pll[0] / 2;
+		break;
+	case 3:
+		sys_info->freq_fman[0] = freq_c_pll[0] / 3;
+		break;
+	case 6:
+		sys_info->freq_fman[0] = freq_c_pll[1] / 2;
+		break;
+	case 7:
+		sys_info->freq_fman[0] = freq_c_pll[1] / 3;
+		break;
+	default:
+		printf("Error: Unknown FMan1 clock select!\n");
+		break;
+	}
+#endif
+
+#define HWA_CGA_M2_CLK_SEL	0x00000007
+#define HWA_CGA_M2_CLK_SHIFT	0
+#ifdef CONFIG_FSL_ESDHC
+	rcw_tmp = in_be32(&gur->rcwsr[15]);
+	rcw_tmp = (rcw_tmp & HWA_CGA_M2_CLK_SEL) >> HWA_CGA_M2_CLK_SHIFT;
+	sys_info->freq_sdhc = freq_c_pll[1] / rcw_tmp;
+#endif
+
+#if defined(CONFIG_FSL_IFC)
+	ccr = ifc_in32(&ifc_regs.gregs->ifc_ccr);
+	ccr = ((ccr & IFC_CCR_CLK_DIV_MASK) >> IFC_CCR_CLK_DIV_SHIFT) + 1;
+
+	sys_info->freq_localbus = sys_info->freq_systembus / ccr;
+#endif
+}
+
+int get_clocks(void)
+{
+	struct sys_info sys_info;
+
+	get_sys_info(&sys_info);
+	gd->cpu_clk = sys_info.freq_processor[0];
+	gd->bus_clk = sys_info.freq_systembus;
+	gd->mem_clk = sys_info.freq_ddrbus;
+
+#ifdef CONFIG_FSL_ESDHC
+	gd->arch.sdhc_clk = sys_info.freq_sdhc;
+#endif
+
+	if (gd->cpu_clk != 0)
+		return 0;
+	else
+		return 1;
+}
+
+ulong get_bus_freq(ulong dummy)
+{
+	return gd->bus_clk;
+}
+
+ulong get_ddr_freq(ulong dummy)
+{
+	return gd->mem_clk;
+}
+
+#ifdef CONFIG_FSL_ESDHC
+int get_sdhc_freq(ulong dummy)
+{
+	return gd->arch.sdhc_clk;
+}
+#endif
+
+int get_serial_clock(void)
+{
+	return gd->bus_clk;
+}
+
+unsigned int mxc_get_clock(enum mxc_clock clk)
+{
+	switch (clk) {
+	case MXC_I2C_CLK:
+		return get_bus_freq(0);
+#if defined(CONFIG_FSL_ESDHC)
+	case MXC_ESDHC_CLK:
+		return get_sdhc_freq(0);
+#endif
+	case MXC_DSPI_CLK:
+		return get_bus_freq(0);
+	case MXC_UART_CLK:
+		return get_bus_freq(0);
+	default:
+		printf("Unsupported clock\n");
+	}
+	return 0;
+}

arch/arm/cpu/armv8/fsl-layerscape/fsl_lsch3_serdes.c

@@ -1,5 +1,5 @@
 /*
- * Copyright 2015 Freescale Semiconductor, Inc.
+ * Copyright 2014-2015 Freescale Semiconductor, Inc.
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */
@@ -8,7 +8,7 @@
 #include <asm/io.h>
 #include <asm/errno.h>
 #include <asm/arch/fsl_serdes.h>
-#include <asm/arch-fsl-lsch3/immap_lsch3.h>
+#include <asm/arch/soc.h>
 #include <fsl-mc/ldpaa_wriop.h>
 
 #ifdef CONFIG_SYS_FSL_SRDS_1
@@ -35,7 +35,7 @@ int is_serdes_configured(enum srds_prtcl device)
 int serdes_get_first_lane(u32 sd, enum srds_prtcl device)
 {
 	struct ccsr_gur __iomem *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR);
-	u32 cfg = in_le32(&gur->rcwsr[28]);
+	u32 cfg = gur_in32(&gur->rcwsr[28]);
 	int i;
 
 	switch (sd) {
@@ -76,7 +76,7 @@ void serdes_init(u32 sd, u32 sd_addr, u32 sd_prctl_mask, u32 sd_prctl_shift,
 
 	memset(serdes_prtcl_map, 0, sizeof(serdes_prtcl_map));
 
-	cfg = in_le32(&gur->rcwsr[28]) & sd_prctl_mask;
+	cfg = gur_in32(&gur->rcwsr[28]) & sd_prctl_mask;
 	cfg >>= sd_prctl_shift;
 	printf("Using SERDES%d Protocol: %d (0x%x)\n", sd + 1, cfg, cfg);
 

arch/arm/cpu/armv8/fsl-layerscape/fsl_lsch3_speed.c

@@ -1,5 +1,5 @@
 /*
- * Copyright 2014, Freescale Semiconductor, Inc.
+ * Copyright 2014-2015, Freescale Semiconductor, Inc.
  *
  * SPDX-License-Identifier:	GPL-2.0+
  *
@@ -11,8 +11,8 @@
 #include <fsl_ifc.h>
 #include <asm/processor.h>
 #include <asm/io.h>
-#include <asm/arch-fsl-lsch3/immap_lsch3.h>
 #include <asm/arch/clock.h>
+#include <asm/arch/soc.h>
 #include "cpu.h"
 
 DECLARE_GLOBAL_DATA_PTR;
@@ -83,15 +83,15 @@ void get_sys_info(struct sys_info *sys_info)
 	sys_info->freq_ddrbus2 = sysclk;
 #endif
 
-	sys_info->freq_systembus *= (in_le32(&gur->rcwsr[0]) >>
+	sys_info->freq_systembus *= (gur_in32(&gur->rcwsr[0]) >>
 			FSL_CHASSIS3_RCWSR0_SYS_PLL_RAT_SHIFT) &
 			FSL_CHASSIS3_RCWSR0_SYS_PLL_RAT_MASK;
 	/* Platform clock is half of platform PLL */
 	sys_info->freq_systembus /= 2;
-	sys_info->freq_ddrbus *= (in_le32(&gur->rcwsr[0]) >>
+	sys_info->freq_ddrbus *= (gur_in32(&gur->rcwsr[0]) >>
 			FSL_CHASSIS3_RCWSR0_MEM_PLL_RAT_SHIFT) &
 			FSL_CHASSIS3_RCWSR0_MEM_PLL_RAT_MASK;
-	sys_info->freq_ddrbus2 *= (in_le32(&gur->rcwsr[0]) >>
+	sys_info->freq_ddrbus2 *= (gur_in32(&gur->rcwsr[0]) >>
 			FSL_CHASSIS3_RCWSR0_MEM2_PLL_RAT_SHIFT) &
 			FSL_CHASSIS3_RCWSR0_MEM2_PLL_RAT_MASK;
 
@@ -118,7 +118,7 @@ void get_sys_info(struct sys_info *sys_info)
 	}
 
 #if defined(CONFIG_FSL_IFC)
-	ccr = in_le32(&ifc_regs.gregs->ifc_ccr);
+	ccr = ifc_in32(&ifc_regs.gregs->ifc_ccr);
 	ccr = ((ccr & IFC_CCR_CLK_DIV_MASK) >> IFC_CCR_CLK_DIV_SHIFT) + 1;
 
 	sys_info->freq_localbus = sys_info->freq_systembus / ccr;

arch/arm/cpu/armv8/fsl-layerscape/lowlevel.S

@@ -1,5 +1,5 @@
 /*
- * (C) Copyright 2014 Freescale Semiconductor
+ * (C) Copyright 2014-2015 Freescale Semiconductor
  *
  * SPDX-License-Identifier:	GPL-2.0+
  *
@@ -10,11 +10,14 @@
 #include <linux/linkage.h>
 #include <asm/gic.h>
 #include <asm/macro.h>
-#include "mp.h"
+#ifdef CONFIG_MP
+#include <asm/arch/mp.h>
+#endif
 
 ENTRY(lowlevel_init)
 	mov	x29, lr			/* Save LR */
 
+#ifdef CONFIG_FSL_LSCH3
 	/* Add fully-coherent masters to DVM domain */
 	ldr	x0, =CCI_MN_BASE
 	ldr	x1, =CCI_MN_RNF_NODEID_LIST
@@ -81,6 +84,7 @@ ENTRY(lowlevel_init)
 	ldr	x0, =CCI_S2_QOS_CONTROL_BASE(20)
 	ldr	x1, =0x00FF000C
 	bl	ccn504_set_qos
+#endif
 
 	/* Set the SMMU page size in the sACR register */
 	ldr	x1, =SMMU_BASE
@@ -106,10 +110,12 @@ ENTRY(lowlevel_init)
 
 	branch_if_master x0, x1, 2f
 
+#if defined(CONFIG_MP) && defined(CONFIG_ARMV8_MULTIENTRY)
 	ldr	x0, =secondary_boot_func
 	blr	x0
-2:
+#endif
 
+2:
 #ifdef CONFIG_FSL_TZPC_BP147
 	/* Set Non Secure access for all devices protected via TZPC */
 	ldr	x1, =TZPCDECPROT_0_SET_BASE /* Decode Protection-0 Set Reg */
@@ -245,6 +251,7 @@ ENTRY(__asm_flush_l3_cache)
 	ret
 ENDPROC(__asm_flush_l3_cache)
 
+#ifdef CONFIG_MP
 	/* Keep literals not used by the secondary boot code outside it */
 	.ltorg
 
@@ -353,3 +360,4 @@ __real_cntfrq:
 	/* Secondary Boot Code ends here */
 __secondary_boot_code_size:
 	.quad .-secondary_boot_code
+#endif

arch/arm/cpu/armv8/fsl-layerscape/ls1043a_serdes.c

@@ -0,0 +1,86 @@
+/*
+ * Copyright 2015 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/fsl_serdes.h>
+#include <asm/arch/immap_lsch2.h>
+
+struct serdes_config {
+	u32 protocol;
+	u8 lanes[SRDS_MAX_LANES];
+};
+
+static struct serdes_config serdes1_cfg_tbl[] = {
+	/* SerDes 1 */
+	{0x1555, {XFI_FM1_MAC9, PCIE1, PCIE2, PCIE3} },
+	{0x2555, {SGMII_2500_FM1_DTSEC9, PCIE1, PCIE2, PCIE3} },
+	{0x4555, {QSGMII_FM1_A, PCIE1, PCIE2, PCIE3} },
+	{0x4558, {QSGMII_FM1_A, PCIE1, PCIE2, SATA1} },
+	{0x1355, {XFI_FM1_MAC9, SGMII_FM1_DTSEC2, PCIE2, PCIE3} },
+	{0x2355, {SGMII_2500_FM1_DTSEC9, SGMII_FM1_DTSEC2, PCIE2, PCIE3} },
+	{0x3335, {SGMII_FM1_DTSEC9, SGMII_FM1_DTSEC2, SGMII_FM1_DTSEC5,
+		  PCIE3} },
+	{0x3355, {SGMII_FM1_DTSEC9, SGMII_FM1_DTSEC2, PCIE2, PCIE3} },
+	{0x3358, {SGMII_FM1_DTSEC9, SGMII_FM1_DTSEC2, PCIE2, SATA1} },
+	{0x3555, {SGMII_FM1_DTSEC9, PCIE1, PCIE2, PCIE3} },
+	{0x3558, {SGMII_FM1_DTSEC9, PCIE1, PCIE2, SATA1} },
+	{0x7000, {PCIE1, PCIE1, PCIE1, PCIE1} },
+	{0x9998, {PCIE1, PCIE2, PCIE3, SATA1} },
+	{0x6058, {PCIE1, PCIE1, PCIE2, SATA1} },
+	{0x1455, {XFI_FM1_MAC9, QSGMII_FM1_A, PCIE2, PCIE3} },
+	{0x2455, {SGMII_2500_FM1_DTSEC9, QSGMII_FM1_A, PCIE2, PCIE3} },
+	{0x2255, {SGMII_2500_FM1_DTSEC9, SGMII_2500_FM1_DTSEC2, PCIE2, PCIE3} },
+	{0x3333, {SGMII_FM1_DTSEC9, SGMII_FM1_DTSEC2, SGMII_FM1_DTSEC5,
+		  SGMII_FM1_DTSEC6} },
+	{}
+};
+
+static struct serdes_config *serdes_cfg_tbl[] = {
+	serdes1_cfg_tbl,
+};
+
+enum srds_prtcl serdes_get_prtcl(int serdes, int cfg, int lane)
+{
+	struct serdes_config *ptr;
+
+	if (serdes >= ARRAY_SIZE(serdes_cfg_tbl))
+		return 0;
+
+	ptr = serdes_cfg_tbl[serdes];
+	while (ptr->protocol) {
+		if (ptr->protocol == cfg)
+			return ptr->lanes[lane];
+		ptr++;
+	}
+
+	return 0;
+}
+
+int is_serdes_prtcl_valid(int serdes, u32 prtcl)
+{
+	int i;
+	struct serdes_config *ptr;
+
+	if (serdes >= ARRAY_SIZE(serdes_cfg_tbl))
+		return 0;
+
+	ptr = serdes_cfg_tbl[serdes];
+	while (ptr->protocol) {
+		if (ptr->protocol == prtcl)
+			break;
+		ptr++;
+	}
+
+	if (!ptr->protocol)
+		return 0;
+
+	for (i = 0; i < SRDS_MAX_LANES; i++) {
+		if (ptr->lanes[i] != NONE)
+			return 1;
+	}
+
+	return 0;
+}

arch/arm/cpu/armv8/fsl-layerscape/ls2085a_serdes.c

@@ -1,12 +1,11 @@
 /*
- * Copyright 2015 Freescale Semiconductor, Inc.
+ * Copyright 2014-2015 Freescale Semiconductor, Inc.
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */
 
 #include <common.h>
 #include <asm/arch/fsl_serdes.h>
-#include <asm/arch-fsl-lsch3/immap_lsch3.h>
 
 struct serdes_config {
 	u8 protocol;

arch/arm/cpu/armv8/fsl-layerscape/mp.c

@@ -1,5 +1,5 @@
 /*
- * Copyright 2014 Freescale Semiconductor, Inc.
+ * Copyright 2014-2015 Freescale Semiconductor, Inc.
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */
@@ -7,9 +7,8 @@
 #include <common.h>
 #include <asm/io.h>
 #include <asm/system.h>
-#include <asm/io.h>
-#include <asm/arch-fsl-lsch3/immap_lsch3.h>
-#include "mp.h"
+#include <asm/arch/mp.h>
+#include <asm/arch/soc.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -23,10 +22,14 @@ phys_addr_t determine_mp_bootpg(void)
 	return (phys_addr_t)&secondary_boot_code;
 }
 
-int fsl_lsch3_wake_seconday_cores(void)
+int fsl_layerscape_wake_seconday_cores(void)
 {
 	struct ccsr_gur __iomem *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR);
+#ifdef CONFIG_FSL_LSCH3
 	struct ccsr_reset __iomem *rst = (void *)(CONFIG_SYS_FSL_RST_ADDR);
+#elif defined(CONFIG_FSL_LSCH2)
+	struct ccsr_scfg __iomem *scfg = (void *)(CONFIG_SYS_FSL_SCFG_ADDR);
+#endif
 	u32 cores, cpu_up_mask = 1;
 	int i, timeout = 10;
 	u64 *table = get_spin_tbl_addr();
@@ -48,13 +51,24 @@ int fsl_lsch3_wake_seconday_cores(void)
 			   (CONFIG_MAX_CPUS*SPIN_TABLE_ELEM_SIZE));
 
 	printf("Waking secondary cores to start from %lx\n", gd->relocaddr);
-	out_le32(&gur->bootlocptrh, (u32)(gd->relocaddr >> 32));
-	out_le32(&gur->bootlocptrl, (u32)gd->relocaddr);
-	out_le32(&gur->scratchrw[6], 1);
+
+#ifdef CONFIG_FSL_LSCH3
+	gur_out32(&gur->bootlocptrh, (u32)(gd->relocaddr >> 32));
+	gur_out32(&gur->bootlocptrl, (u32)gd->relocaddr);
+	gur_out32(&gur->scratchrw[6], 1);
 	asm volatile("dsb st" : : : "memory");
 	rst->brrl = cores;
 	asm volatile("dsb st" : : : "memory");
+#elif defined(CONFIG_FSL_LSCH2)
+	scfg_out32(&scfg->scratchrw[0], (u32)(gd->relocaddr >> 32));
+	scfg_out32(&scfg->scratchrw[1], (u32)gd->relocaddr);
+	asm volatile("dsb st" : : : "memory");
+	gur_out32(&gur->brrl, cores);
+	asm volatile("dsb st" : : : "memory");
 
+	/* Bootup online cores */
+	scfg_out32(&scfg->corebcr, cores);
+#endif
 	/* This is needed as a precautionary measure.
 	 * If some code before this has accidentally  released the secondary
 	 * cores then the pre-bootloader code will trap them in a "wfe" unless

arch/arm/cpu/armv8/fsl-layerscape/soc.c

@@ -1,19 +1,18 @@
 /*
- * Copyright 2015 Freescale Semiconductor
+ * Copyright 2014-2015 Freescale Semiconductor
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */
 
 #include <common.h>
 #include <fsl_ifc.h>
-#include <nand.h>
-#include <spl.h>
-#include <asm/arch-fsl-lsch3/soc.h>
+#include <asm/arch/soc.h>
 #include <asm/io.h>
 #include <asm/global_data.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
+#ifdef CONFIG_LS2085A
 static void erratum_a008751(void)
 {
 #ifdef CONFIG_SYS_FSL_ERRATUM_A008751
@@ -78,30 +77,27 @@ void fsl_lsch3_early_init_f(void)
 	erratum_a009203();
 }
 
-#ifdef CONFIG_SPL_BUILD
-void board_init_f(ulong dummy)
+#elif defined(CONFIG_LS1043A)
+void fsl_lsch2_early_init_f(void)
 {
-	/* Clear global data */
-	memset((void *)gd, 0, sizeof(gd_t));
+	struct ccsr_cci400 *cci = (struct ccsr_cci400 *)CONFIG_SYS_CCI400_ADDR;
 
-	arch_cpu_init();
-	board_early_init_f();
-	timer_init();
-	env_init();
-	gd->baudrate = getenv_ulong("baudrate", 10, CONFIG_BAUDRATE);
+#ifdef CONFIG_FSL_IFC
+	init_early_memctl_regs();	/* tighten IFC timing */
+#endif
 
-	serial_init();
-	console_init_f();
-	dram_init();
-
-	/* Clear the BSS. */
-	memset(__bss_start, 0, __bss_end - __bss_start);
-
-	board_init_r(NULL, 0);
-}
-
-u32 spl_boot_device(void)
-{
-	return BOOT_DEVICE_NAND;
+	/*
+	 * Enable snoop requests and DVM message requests for
+	 * Slave insterface S4 (A53 core cluster)
+	 */
+	out_le32(&cci->slave[4].snoop_ctrl,
+		 CCI400_DVM_MESSAGE_REQ_EN | CCI400_SNOOP_REQ_EN);
+}
+#endif
+
+#ifdef CONFIG_BOARD_LATE_INIT
+int board_late_init(void)
+{
+	return 0;
 }
 #endif

arch/arm/cpu/armv8/fsl-layerscape/spl.c

@@ -0,0 +1,79 @@
+/*
+ * Copyright 2014-2015 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <spl.h>
+#include <asm/io.h>
+#include <fsl_ifc.h>
+#include <fsl_csu.h>
+#include <i2c.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+u32 spl_boot_device(void)
+{
+#ifdef CONFIG_SPL_MMC_SUPPORT
+	return BOOT_DEVICE_MMC1;
+#endif
+#ifdef CONFIG_SPL_NAND_SUPPORT
+	return BOOT_DEVICE_NAND;
+#endif
+	return 0;
+}
+
+u32 spl_boot_mode(void)
+{
+	switch (spl_boot_device()) {
+	case BOOT_DEVICE_MMC1:
+#ifdef CONFIG_SPL_FAT_SUPPORT
+		return MMCSD_MODE_FAT;
+#else
+		return MMCSD_MODE_RAW;
+#endif
+	case BOOT_DEVICE_NAND:
+		return 0;
+	default:
+		puts("spl: error: unsupported device\n");
+		hang();
+	}
+}
+
+#ifdef CONFIG_SPL_BUILD
+void board_init_f(ulong dummy)
+{
+	/* Set global data pointer */
+	gd = &gdata;
+	/* Clear global data */
+	memset((void *)gd, 0, sizeof(gd_t));
+#ifdef CONFIG_LS2085A
+	arch_cpu_init();
+#endif
+#ifdef CONFIG_FSL_IFC
+	init_early_memctl_regs();
+#endif
+	board_early_init_f();
+	timer_init();
+#ifdef CONFIG_LS2085A
+	env_init();
+#endif
+	get_clocks();
+
+	preloader_console_init();
+
+#ifdef CONFIG_SPL_I2C_SUPPORT
+	i2c_init_all();
+#endif
+	dram_init();
+
+	/* Clear the BSS */
+	memset(__bss_start, 0, __bss_end - __bss_start);
+
+#ifdef CONFIG_LAYERSCAPE_NS_ACCESS
+	enable_layerscape_ns_access();
+#endif
+	board_init_r(NULL, 0);
+}
+#endif

arch/arm/cpu/armv8/fsl-lsch3/Makefile

@@ -1,13 +0,0 @@
-#
-# Copyright 2014, Freescale Semiconductor
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-
-obj-y += cpu.o
-obj-y += lowlevel.o
-obj-y += soc.o
-obj-y += speed.o
-obj-$(CONFIG_SYS_HAS_SERDES) += fsl_lsch3_serdes.o ls2085a_serdes.o
-obj-$(CONFIG_MP) += mp.o
-obj-$(CONFIG_OF_LIBFDT) += fdt.o

arch/arm/cpu/armv8/fsl-lsch3/speed.h

@@ -1,7 +0,0 @@
-/*
- * Copyright 2014, Freescale Semiconductor, Inc.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-void get_sys_info(struct sys_info *sys_info);

arch/arm/cpu/u-boot.lds

@@ -14,6 +14,23 @@ OUTPUT_ARCH(arm)
 ENTRY(_start)
 SECTIONS
 {
+	/*
+	 * Discard the relocation entries for secure text.
+	 * The secure code is bundled with u-boot image, so there will
+	 * be relocations entries for the secure code, since we use
+	 * "-mword-relocations" to compile and "-pie" to link into the
+	 * final image. We do not need the relocation entries for secure
+	 * code, because secure code will not be relocated, it only needs
+	 * to be copied from loading address to CONFIG_ARMV7_SECURE_BASE,
+	 * which is the linking and running address for secure code.
+	 * If keep the relocation entries in .rel.dyn section,
+	 * "relocation offset + linking address" may locates into an
+	 * address that is reserved by SoC, then will trigger data abort.
+	 *
+	 * The reason that move .rel._secure at the beginning, is to
+	 * avoid hole in the final image.
+	 */
+	/DISCARD/ : { *(.rel._secure*) }
 	. = 0x00000000;
 
 	. = ALIGN(4);

arch/arm/dts/Makefile

@@ -1,3 +1,7 @@
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
 dtb-$(CONFIG_S5PC100) += s5pc1xx-smdkc100.dtb
 dtb-$(CONFIG_S5PC110) += s5pc1xx-goni.dtb
 dtb-$(CONFIG_EXYNOS4) += exynos4210-origen.dtb \
@@ -41,6 +45,11 @@ dtb-$(CONFIG_TEGRA) += tegra20-harmony.dtb \
 	tegra210-p2371-0000.dtb \
 	tegra210-p2371-2180.dtb \
 	tegra210-p2571.dtb
+
+dtb-$(CONFIG_ARCH_MVEBU) +=			\
+	armada-388-gp.dtb			\
+	armada-xp-gp.dtb
+
 dtb-$(CONFIG_ARCH_UNIPHIER) += \
 	uniphier-ph1-ld4-ref.dtb \
 	uniphier-ph1-ld6b-ref.dtb \
@@ -60,7 +69,10 @@ dtb-$(CONFIG_ARCH_ZYNQ) += zynq-zc702.dtb \
 	zynq-zc770-xm011.dtb \
 	zynq-zc770-xm012.dtb \
 	zynq-zc770-xm013.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += \
+	zynqmp-ep108.dtb
 dtb-$(CONFIG_AM33XX) += am335x-boneblack.dtb am335x-evm.dtb
+dtb-$(CONFIG_AM43XX) += am437x-gp-evm.dtb am437x-sk-evm.dtb
 
 dtb-$(CONFIG_ARCH_SOCFPGA) +=				\
 	socfpga_arria5_socdk.dtb			\
@@ -69,7 +81,8 @@ dtb-$(CONFIG_ARCH_SOCFPGA) +=				\
 	socfpga_cyclone5_de0_nano_soc.dtb			\
 	socfpga_cyclone5_sockit.dtb			\
 	socfpga_cyclone5_socrates.dtb
-dtb-$(CONFIG_TARGET_DRA7XX_EVM) += dra72-evm.dtb
+dtb-$(CONFIG_TARGET_DRA7XX_EVM) += dra72-evm.dtb dra7-evm.dtb
+dtb-$(CONFIG_TARGET_BEAGLE_X15) += am57xx-beagle-x15.dtb
 dtb-$(CONFIG_TARGET_STV0991) += stv0991.dtb
 
 dtb-$(CONFIG_LS102XA) += ls1021a-qds.dtb \
@@ -107,15 +120,14 @@ dtb-$(CONFIG_MACH_SUN5I) += \
 	sun5i-a10s-r7-tv-dongle.dtb \
 	sun5i-a10s-wobo-i5.dtb \
 	sun5i-a13-ampe-a76.dtb \
-	sun5i-a13-forfun-q88db.dtb \
 	sun5i-a13-hsg-h702.dtb \
 	sun5i-a13-inet-86vs.dtb \
 	sun5i-a13-inet-98v-rev2.dtb \
 	sun5i-a13-olinuxino.dtb \
 	sun5i-a13-olinuxino-micro.dtb \
 	sun5i-a13-q8-tablet.dtb \
-	sun5i-a13-tzx-q8-713b7.dtb \
-	sun5i-a13-utoo-p66.dtb
+	sun5i-a13-utoo-p66.dtb \
+	sun5i-r8-chip.dtb
 dtb-$(CONFIG_MACH_SUN6I) += \
 	sun6i-a31-app4-evb1.dtb \
 	sun6i-a31-colombus.dtb \
@@ -125,7 +137,8 @@ dtb-$(CONFIG_MACH_SUN6I) += \
 	sun6i-a31-mele-a1000g-quad.dtb \
 	sun6i-a31-mixtile-loftq.dtb \
 	sun6i-a31s-cs908.dtb \
-	sun6i-a31s-primo81.dtb
+	sun6i-a31s-primo81.dtb \
+	sun6i-a31s-sinovoip-bpi-m2.dtb
 dtb-$(CONFIG_MACH_SUN7I) += \
 	sun7i-a20-ainol-aw1.dtb \
 	sun7i-a20-bananapi.dtb \
@@ -152,13 +165,9 @@ dtb-$(CONFIG_MACH_SUN7I) += \
 dtb-$(CONFIG_MACH_SUN8I_A23) += \
 	sun8i-a23-evb.dtb \
 	sun8i-a23-gt90h-v4.dtb \
-	sun8i-a23-ippo-q8h-v5.dtb \
-	sun8i-a23-ippo-q8h-v1.2.dtb \
 	sun8i-a23-q8-tablet.dtb
 dtb-$(CONFIG_MACH_SUN8I_A33) += \
-	sun8i-a33-et-q8-v1.6.dtb \
 	sun8i-a33-ga10h-v1.1.dtb \
-	sun8i-a33-ippo-q8h-v1.2.dtb \
 	sun8i-a33-q8-tablet.dtb \
 	sun8i-a33-sinlinx-sina33.dtb
 dtb-$(CONFIG_MACH_SUN9I) += \
@@ -168,6 +177,11 @@ dtb-$(CONFIG_MACH_SUN9I) += \
 dtb-$(CONFIG_VF610) += vf500-colibri.dtb \
 	vf610-colibri.dtb
 
+dtb-$(CONFIG_SOC_KEYSTONE) += k2hk-evm.dtb \
+	k2l-evm.dtb \
+	k2e-evm.dtb \
+	k2g-evm.dtb
+
 targets += $(dtb-y)
 
 # Add any required device tree compiler flags here

arch/arm/dts/am4372.dtsi

@@ -0,0 +1,999 @@
+/*
+ * Device Tree Source for AM4372 SoC
+ *
+ * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2.  This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+#include "skeleton.dtsi"
+
+/ {
+	compatible = "ti,am4372", "ti,am43";
+	interrupt-parent = <&wakeupgen>;
+
+
+	aliases {
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
+		serial0 = &uart0;
+		ethernet0 = &cpsw_emac0;
+		ethernet1 = &cpsw_emac1;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		cpu: cpu@0 {
+			compatible = "arm,cortex-a9";
+			device_type = "cpu";
+			reg = <0>;
+
+			clocks = <&dpll_mpu_ck>;
+			clock-names = "cpu";
+
+			clock-latency = <300000>; /* From omap-cpufreq driver */
+		};
+	};
+
+	gic: interrupt-controller@48241000 {
+		compatible = "arm,cortex-a9-gic";
+		interrupt-controller;
+		#interrupt-cells = <3>;
+		reg = <0x48241000 0x1000>,
+		      <0x48240100 0x0100>;
+		interrupt-parent = <&gic>;
+	};
+
+	wakeupgen: interrupt-controller@48281000 {
+		compatible = "ti,omap4-wugen-mpu";
+		interrupt-controller;
+		#interrupt-cells = <3>;
+		reg = <0x48281000 0x1000>;
+		interrupt-parent = <&gic>;
+	};
+
+	l2-cache-controller@48242000 {
+		compatible = "arm,pl310-cache";
+		reg = <0x48242000 0x1000>;
+		cache-unified;
+		cache-level = <2>;
+	};
+
+	ocp {
+		compatible = "ti,am4372-l3-noc", "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		ti,hwmods = "l3_main";
+		reg = <0x44000000 0x400000
+		       0x44800000 0x400000>;
+		interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+
+		l4_wkup: l4_wkup@44c00000 {
+			compatible = "ti,am4-l4-wkup", "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x44c00000 0x287000>;
+
+			prcm: prcm@1f0000 {
+				compatible = "ti,am4-prcm";
+				reg = <0x1f0000 0x11000>;
+
+				prcm_clocks: clocks {
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+
+				prcm_clockdomains: clockdomains {
+				};
+			};
+
+			scm: scm@210000 {
+				compatible = "ti,am4-scm", "simple-bus";
+				reg = <0x210000 0x4000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0 0x210000 0x4000>;
+
+				am43xx_pinmux: pinmux@800 {
+					compatible = "ti,am437-padconf",
+						     "pinctrl-single";
+					reg = <0x800 0x31c>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					#interrupt-cells = <1>;
+					interrupt-controller;
+					pinctrl-single,register-width = <32>;
+					pinctrl-single,function-mask = <0xffffffff>;
+				};
+
+				scm_conf: scm_conf@0 {
+					compatible = "syscon";
+					reg = <0x0 0x800>;
+					#address-cells = <1>;
+					#size-cells = <1>;
+
+					scm_clocks: clocks {
+						#address-cells = <1>;
+						#size-cells = <0>;
+					};
+				};
+
+				scm_clockdomains: clockdomains {
+				};
+			};
+		};
+
+		emif: emif@4c000000 {
+			compatible = "ti,emif-am4372";
+			reg = <0x4c000000 0x1000000>;
+			ti,hwmods = "emif";
+		};
+
+		edma: edma@49000000 {
+			compatible = "ti,edma3";
+			ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2";
+			reg =	<0x49000000 0x10000>,
+				<0x44e10f90 0x10>;
+			interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+			#dma-cells = <1>;
+		};
+
+		uart0: serial@44e09000 {
+			compatible = "ti,am4372-uart","ti,omap2-uart";
+			reg = <0x44e09000 0x2000>;
+			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "uart1";
+		};
+
+		uart1: serial@48022000 {
+			compatible = "ti,am4372-uart","ti,omap2-uart";
+			reg = <0x48022000 0x2000>;
+			interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "uart2";
+			status = "disabled";
+		};
+
+		uart2: serial@48024000 {
+			compatible = "ti,am4372-uart","ti,omap2-uart";
+			reg = <0x48024000 0x2000>;
+			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "uart3";
+			status = "disabled";
+		};
+
+		uart3: serial@481a6000 {
+			compatible = "ti,am4372-uart","ti,omap2-uart";
+			reg = <0x481a6000 0x2000>;
+			interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "uart4";
+			status = "disabled";
+		};
+
+		uart4: serial@481a8000 {
+			compatible = "ti,am4372-uart","ti,omap2-uart";
+			reg = <0x481a8000 0x2000>;
+			interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "uart5";
+			status = "disabled";
+		};
+
+		uart5: serial@481aa000 {
+			compatible = "ti,am4372-uart","ti,omap2-uart";
+			reg = <0x481aa000 0x2000>;
+			interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "uart6";
+			status = "disabled";
+		};
+
+		mailbox: mailbox@480C8000 {
+			compatible = "ti,omap4-mailbox";
+			reg = <0x480C8000 0x200>;
+			interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "mailbox";
+			#mbox-cells = <1>;
+			ti,mbox-num-users = <4>;
+			ti,mbox-num-fifos = <8>;
+			mbox_wkupm3: wkup_m3 {
+				ti,mbox-tx = <0 0 0>;
+				ti,mbox-rx = <0 0 3>;
+			};
+		};
+
+		timer1: timer@44e31000 {
+			compatible = "ti,am4372-timer-1ms","ti,am335x-timer-1ms";
+			reg = <0x44e31000 0x400>;
+			interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+			ti,timer-alwon;
+			ti,hwmods = "timer1";
+		};
+
+		timer2: timer@48040000  {
+			compatible = "ti,am4372-timer","ti,am335x-timer";
+			reg = <0x48040000  0x400>;
+			interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "timer2";
+		};
+
+		timer3: timer@48042000 {
+			compatible = "ti,am4372-timer","ti,am335x-timer";
+			reg = <0x48042000 0x400>;
+			interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "timer3";
+			status = "disabled";
+		};
+
+		timer4: timer@48044000 {
+			compatible = "ti,am4372-timer","ti,am335x-timer";
+			reg = <0x48044000 0x400>;
+			interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
+			ti,timer-pwm;
+			ti,hwmods = "timer4";
+			status = "disabled";
+		};
+
+		timer5: timer@48046000 {
+			compatible = "ti,am4372-timer","ti,am335x-timer";
+			reg = <0x48046000 0x400>;
+			interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
+			ti,timer-pwm;
+			ti,hwmods = "timer5";
+			status = "disabled";
+		};
+
+		timer6: timer@48048000 {
+			compatible = "ti,am4372-timer","ti,am335x-timer";
+			reg = <0x48048000 0x400>;
+			interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
+			ti,timer-pwm;
+			ti,hwmods = "timer6";
+			status = "disabled";
+		};
+
+		timer7: timer@4804a000 {
+			compatible = "ti,am4372-timer","ti,am335x-timer";
+			reg = <0x4804a000 0x400>;
+			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+			ti,timer-pwm;
+			ti,hwmods = "timer7";
+			status = "disabled";
+		};
+
+		timer8: timer@481c1000 {
+			compatible = "ti,am4372-timer","ti,am335x-timer";
+			reg = <0x481c1000 0x400>;
+			interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "timer8";
+			status = "disabled";
+		};
+
+		timer9: timer@4833d000 {
+			compatible = "ti,am4372-timer","ti,am335x-timer";
+			reg = <0x4833d000 0x400>;
+			interrupts = <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "timer9";
+			status = "disabled";
+		};
+
+		timer10: timer@4833f000 {
+			compatible = "ti,am4372-timer","ti,am335x-timer";
+			reg = <0x4833f000 0x400>;
+			interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "timer10";
+			status = "disabled";
+		};
+
+		timer11: timer@48341000 {
+			compatible = "ti,am4372-timer","ti,am335x-timer";
+			reg = <0x48341000 0x400>;
+			interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "timer11";
+			status = "disabled";
+		};
+
+		counter32k: counter@44e86000 {
+			compatible = "ti,am4372-counter32k","ti,omap-counter32k";
+			reg = <0x44e86000 0x40>;
+			ti,hwmods = "counter_32k";
+		};
+
+		rtc: rtc@44e3e000 {
+			compatible = "ti,am4372-rtc","ti,da830-rtc";
+			reg = <0x44e3e000 0x1000>;
+			interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "rtc";
+			status = "disabled";
+		};
+
+		wdt: wdt@44e35000 {
+			compatible = "ti,am4372-wdt","ti,omap3-wdt";
+			reg = <0x44e35000 0x1000>;
+			interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "wd_timer2";
+		};
+
+		gpio0: gpio@44e07000 {
+			compatible = "ti,am4372-gpio","ti,omap4-gpio";
+			reg = <0x44e07000 0x1000>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			ti,hwmods = "gpio1";
+			status = "disabled";
+		};
+
+		gpio1: gpio@4804c000 {
+			compatible = "ti,am4372-gpio","ti,omap4-gpio";
+			reg = <0x4804c000 0x1000>;
+			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			ti,hwmods = "gpio2";
+			status = "disabled";
+		};
+
+		gpio2: gpio@481ac000 {
+			compatible = "ti,am4372-gpio","ti,omap4-gpio";
+			reg = <0x481ac000 0x1000>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			ti,hwmods = "gpio3";
+			status = "disabled";
+		};
+
+		gpio3: gpio@481ae000 {
+			compatible = "ti,am4372-gpio","ti,omap4-gpio";
+			reg = <0x481ae000 0x1000>;
+			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			ti,hwmods = "gpio4";
+			status = "disabled";
+		};
+
+		gpio4: gpio@48320000 {
+			compatible = "ti,am4372-gpio","ti,omap4-gpio";
+			reg = <0x48320000 0x1000>;
+			interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			ti,hwmods = "gpio5";
+			status = "disabled";
+		};
+
+		gpio5: gpio@48322000 {
+			compatible = "ti,am4372-gpio","ti,omap4-gpio";
+			reg = <0x48322000 0x1000>;
+			interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			ti,hwmods = "gpio6";
+			status = "disabled";
+		};
+
+		hwspinlock: spinlock@480ca000 {
+			compatible = "ti,omap4-hwspinlock";
+			reg = <0x480ca000 0x1000>;
+			ti,hwmods = "spinlock";
+			#hwlock-cells = <1>;
+		};
+
+		i2c0: i2c@44e0b000 {
+			compatible = "ti,am4372-i2c","ti,omap4-i2c";
+			reg = <0x44e0b000 0x1000>;
+			interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "i2c1";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c1: i2c@4802a000 {
+			compatible = "ti,am4372-i2c","ti,omap4-i2c";
+			reg = <0x4802a000 0x1000>;
+			interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "i2c2";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c2: i2c@4819c000 {
+			compatible = "ti,am4372-i2c","ti,omap4-i2c";
+			reg = <0x4819c000 0x1000>;
+			interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "i2c3";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		spi0: spi@48030000 {
+			compatible = "ti,am4372-mcspi","ti,omap4-mcspi";
+			reg = <0x48030000 0x400>;
+			interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "spi0";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		mmc1: mmc@48060000 {
+			compatible = "ti,omap4-hsmmc";
+			reg = <0x48060000 0x1000>;
+			ti,hwmods = "mmc1";
+			ti,dual-volt;
+			ti,needs-special-reset;
+			dmas = <&edma 24
+				&edma 25>;
+			dma-names = "tx", "rx";
+			interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		mmc2: mmc@481d8000 {
+			compatible = "ti,omap4-hsmmc";
+			reg = <0x481d8000 0x1000>;
+			ti,hwmods = "mmc2";
+			ti,needs-special-reset;
+			dmas = <&edma 2
+				&edma 3>;
+			dma-names = "tx", "rx";
+			interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		mmc3: mmc@47810000 {
+			compatible = "ti,omap4-hsmmc";
+			reg = <0x47810000 0x1000>;
+			ti,hwmods = "mmc3";
+			ti,needs-special-reset;
+			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		spi1: spi@481a0000 {
+			compatible = "ti,am4372-mcspi","ti,omap4-mcspi";
+			reg = <0x481a0000 0x400>;
+			interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "spi1";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		spi2: spi@481a2000 {
+			compatible = "ti,am4372-mcspi","ti,omap4-mcspi";
+			reg = <0x481a2000 0x400>;
+			interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "spi2";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		spi3: spi@481a4000 {
+			compatible = "ti,am4372-mcspi","ti,omap4-mcspi";
+			reg = <0x481a4000 0x400>;
+			interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "spi3";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		spi4: spi@48345000 {
+			compatible = "ti,am4372-mcspi","ti,omap4-mcspi";
+			reg = <0x48345000 0x400>;
+			interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "spi4";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		mac: ethernet@4a100000 {
+			compatible = "ti,am4372-cpsw","ti,cpsw";
+			reg = <0x4a100000 0x800
+			       0x4a101200 0x100>;
+			interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ti,hwmods = "cpgmac0";
+			clocks = <&cpsw_125mhz_gclk>, <&cpsw_cpts_rft_clk>;
+			clock-names = "fck", "cpts";
+			status = "disabled";
+			cpdma_channels = <8>;
+			ale_entries = <1024>;
+			bd_ram_size = <0x2000>;
+			no_bd_ram = <0>;
+			rx_descs = <64>;
+			mac_control = <0x20>;
+			slaves = <2>;
+			active_slave = <0>;
+			cpts_clock_mult = <0x80000000>;
+			cpts_clock_shift = <29>;
+			ranges;
+
+			davinci_mdio: mdio@4a101000 {
+				compatible = "ti,am4372-mdio","ti,davinci_mdio";
+				reg = <0x4a101000 0x100>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				ti,hwmods = "davinci_mdio";
+				bus_freq = <1000000>;
+				status = "disabled";
+			};
+
+			cpsw_emac0: slave@4a100200 {
+				/* Filled in by U-Boot */
+				mac-address = [ 00 00 00 00 00 00 ];
+			};
+
+			cpsw_emac1: slave@4a100300 {
+				/* Filled in by U-Boot */
+				mac-address = [ 00 00 00 00 00 00 ];
+			};
+
+			phy_sel: cpsw-phy-sel@44e10650 {
+				compatible = "ti,am43xx-cpsw-phy-sel";
+				reg= <0x44e10650 0x4>;
+				reg-names = "gmii-sel";
+			};
+		};
+
+		epwmss0: epwmss@48300000 {
+			compatible = "ti,am4372-pwmss","ti,am33xx-pwmss";
+			reg = <0x48300000 0x10>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			ti,hwmods = "epwmss0";
+			status = "disabled";
+
+			ecap0: ecap@48300100 {
+				compatible = "ti,am4372-ecap","ti,am33xx-ecap";
+				#pwm-cells = <3>;
+				reg = <0x48300100 0x80>;
+				ti,hwmods = "ecap0";
+				status = "disabled";
+			};
+
+			ehrpwm0: ehrpwm@48300200 {
+				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				#pwm-cells = <3>;
+				reg = <0x48300200 0x80>;
+				ti,hwmods = "ehrpwm0";
+				status = "disabled";
+			};
+		};
+
+		epwmss1: epwmss@48302000 {
+			compatible = "ti,am4372-pwmss","ti,am33xx-pwmss";
+			reg = <0x48302000 0x10>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			ti,hwmods = "epwmss1";
+			status = "disabled";
+
+			ecap1: ecap@48302100 {
+				compatible = "ti,am4372-ecap","ti,am33xx-ecap";
+				#pwm-cells = <3>;
+				reg = <0x48302100 0x80>;
+				ti,hwmods = "ecap1";
+				status = "disabled";
+			};
+
+			ehrpwm1: ehrpwm@48302200 {
+				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				#pwm-cells = <3>;
+				reg = <0x48302200 0x80>;
+				ti,hwmods = "ehrpwm1";
+				status = "disabled";
+			};
+		};
+
+		epwmss2: epwmss@48304000 {
+			compatible = "ti,am4372-pwmss","ti,am33xx-pwmss";
+			reg = <0x48304000 0x10>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			ti,hwmods = "epwmss2";
+			status = "disabled";
+
+			ecap2: ecap@48304100 {
+				compatible = "ti,am4372-ecap","ti,am33xx-ecap";
+				#pwm-cells = <3>;
+				reg = <0x48304100 0x80>;
+				ti,hwmods = "ecap2";
+				status = "disabled";
+			};
+
+			ehrpwm2: ehrpwm@48304200 {
+				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				#pwm-cells = <3>;
+				reg = <0x48304200 0x80>;
+				ti,hwmods = "ehrpwm2";
+				status = "disabled";
+			};
+		};
+
+		epwmss3: epwmss@48306000 {
+			compatible = "ti,am4372-pwmss","ti,am33xx-pwmss";
+			reg = <0x48306000 0x10>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			ti,hwmods = "epwmss3";
+			status = "disabled";
+
+			ehrpwm3: ehrpwm@48306200 {
+				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				#pwm-cells = <3>;
+				reg = <0x48306200 0x80>;
+				ti,hwmods = "ehrpwm3";
+				status = "disabled";
+			};
+		};
+
+		epwmss4: epwmss@48308000 {
+			compatible = "ti,am4372-pwmss","ti,am33xx-pwmss";
+			reg = <0x48308000 0x10>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			ti,hwmods = "epwmss4";
+			status = "disabled";
+
+			ehrpwm4: ehrpwm@48308200 {
+				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				#pwm-cells = <3>;
+				reg = <0x48308200 0x80>;
+				ti,hwmods = "ehrpwm4";
+				status = "disabled";
+			};
+		};
+
+		epwmss5: epwmss@4830a000 {
+			compatible = "ti,am4372-pwmss","ti,am33xx-pwmss";
+			reg = <0x4830a000 0x10>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			ti,hwmods = "epwmss5";
+			status = "disabled";
+
+			ehrpwm5: ehrpwm@4830a200 {
+				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				#pwm-cells = <3>;
+				reg = <0x4830a200 0x80>;
+				ti,hwmods = "ehrpwm5";
+				status = "disabled";
+			};
+		};
+
+		tscadc: tscadc@44e0d000 {
+			compatible = "ti,am3359-tscadc";
+			reg = <0x44e0d000 0x1000>;
+			ti,hwmods = "adc_tsc";
+			interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&adc_tsc_fck>;
+			clock-names = "fck";
+			status = "disabled";
+
+			tsc {
+				compatible = "ti,am3359-tsc";
+			};
+
+			adc {
+				#io-channel-cells = <1>;
+				compatible = "ti,am3359-adc";
+			};
+
+		};
+
+		sham: sham@53100000 {
+			compatible = "ti,omap5-sham";
+			ti,hwmods = "sham";
+			reg = <0x53100000 0x300>;
+			dmas = <&edma 36>;
+			dma-names = "rx";
+			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		aes: aes@53501000 {
+			compatible = "ti,omap4-aes";
+			ti,hwmods = "aes";
+			reg = <0x53501000 0xa0>;
+			interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&edma 6
+				&edma 5>;
+			dma-names = "tx", "rx";
+		};
+
+		des: des@53701000 {
+			compatible = "ti,omap4-des";
+			ti,hwmods = "des";
+			reg = <0x53701000 0xa0>;
+			interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&edma 34
+				&edma 33>;
+			dma-names = "tx", "rx";
+		};
+
+		mcasp0: mcasp@48038000 {
+			compatible = "ti,am33xx-mcasp-audio";
+			ti,hwmods = "mcasp0";
+			reg = <0x48038000 0x2000>,
+			      <0x46000000 0x400000>;
+			reg-names = "mpu", "dat";
+			interrupts = <80>, <81>;
+			interrupt-names = "tx", "rx";
+			status = "disabled";
+			dmas = <&edma 8>,
+			       <&edma 9>;
+			dma-names = "tx", "rx";
+		};
+
+		mcasp1: mcasp@4803C000 {
+			compatible = "ti,am33xx-mcasp-audio";
+			ti,hwmods = "mcasp1";
+			reg = <0x4803C000 0x2000>,
+			      <0x46400000 0x400000>;
+			reg-names = "mpu", "dat";
+			interrupts = <82>, <83>;
+			interrupt-names = "tx", "rx";
+			status = "disabled";
+			dmas = <&edma 10>,
+			       <&edma 11>;
+			dma-names = "tx", "rx";
+		};
+
+		elm: elm@48080000 {
+			compatible = "ti,am3352-elm";
+			reg = <0x48080000 0x2000>;
+			interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "elm";
+			clocks = <&l4ls_gclk>;
+			clock-names = "fck";
+			status = "disabled";
+		};
+
+		gpmc: gpmc@50000000 {
+			compatible = "ti,am3352-gpmc";
+			ti,hwmods = "gpmc";
+			clocks = <&l3s_gclk>;
+			clock-names = "fck";
+			reg = <0x50000000 0x2000>;
+			interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+			gpmc,num-cs = <7>;
+			gpmc,num-waitpins = <2>;
+			#address-cells = <2>;
+			#size-cells = <1>;
+			status = "disabled";
+		};
+
+		am43xx_control_usb2phy1: control-phy@44e10620 {
+			compatible = "ti,control-phy-usb2-am437";
+			reg = <0x44e10620 0x4>;
+			reg-names = "power";
+		};
+
+		am43xx_control_usb2phy2: control-phy@0x44e10628 {
+			compatible = "ti,control-phy-usb2-am437";
+			reg = <0x44e10628 0x4>;
+			reg-names = "power";
+		};
+
+		ocp2scp0: ocp2scp@483a8000 {
+			compatible = "ti,am437x-ocp2scp", "ti,omap-ocp2scp";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			ti,hwmods = "ocp2scp0";
+
+			usb2_phy1: phy@483a8000 {
+				compatible = "ti,am437x-usb2";
+				reg = <0x483a8000 0x8000>;
+				ctrl-module = <&am43xx_control_usb2phy1>;
+				clocks = <&usb_phy0_always_on_clk32k>,
+					 <&usb_otg_ss0_refclk960m>;
+				clock-names = "wkupclk", "refclk";
+				#phy-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		ocp2scp1: ocp2scp@483e8000 {
+			compatible = "ti,am437x-ocp2scp", "ti,omap-ocp2scp";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			ti,hwmods = "ocp2scp1";
+
+			usb2_phy2: phy@483e8000 {
+				compatible = "ti,am437x-usb2";
+				reg = <0x483e8000 0x8000>;
+				ctrl-module = <&am43xx_control_usb2phy2>;
+				clocks = <&usb_phy1_always_on_clk32k>,
+					 <&usb_otg_ss1_refclk960m>;
+				clock-names = "wkupclk", "refclk";
+				#phy-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		dwc3_1: omap_dwc3@48380000 {
+			compatible = "ti,am437x-dwc3";
+			ti,hwmods = "usb_otg_ss0";
+			reg = <0x48380000 0x10000>;
+			interrupts = <GIC_SPI 172 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			utmi-mode = <1>;
+			ranges;
+
+			usb1: usb@48390000 {
+				compatible = "synopsys,dwc3";
+				reg = <0x48390000 0x10000>;
+				interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
+				phys = <&usb2_phy1>;
+				phy-names = "usb2-phy";
+				maximum-speed = "high-speed";
+				dr_mode = "otg";
+				status = "disabled";
+				snps,dis_u3_susphy_quirk;
+				snps,dis_u2_susphy_quirk;
+			};
+		};
+
+		dwc3_2: omap_dwc3@483c0000 {
+			compatible = "ti,am437x-dwc3";
+			ti,hwmods = "usb_otg_ss1";
+			reg = <0x483c0000 0x10000>;
+			interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			utmi-mode = <1>;
+			ranges;
+
+			usb2: usb@483d0000 {
+				compatible = "synopsys,dwc3";
+				reg = <0x483d0000 0x10000>;
+				interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
+				phys = <&usb2_phy2>;
+				phy-names = "usb2-phy";
+				maximum-speed = "high-speed";
+				dr_mode = "otg";
+				status = "disabled";
+				snps,dis_u3_susphy_quirk;
+				snps,dis_u2_susphy_quirk;
+			};
+		};
+
+		qspi: qspi@47900000 {
+			compatible = "ti,am4372-qspi";
+			reg = <0x47900000 0x100>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			ti,hwmods = "qspi";
+			interrupts = <0 138 0x4>;
+			num-cs = <4>;
+			status = "disabled";
+		};
+
+		hdq: hdq@48347000 {
+			compatible = "ti,am4372-hdq";
+			reg = <0x48347000 0x1000>;
+			interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&func_12m_clk>;
+			clock-names = "fck";
+			ti,hwmods = "hdq1w";
+			status = "disabled";
+		};
+
+		dss: dss@4832a000 {
+			compatible = "ti,omap3-dss";
+			reg = <0x4832a000 0x200>;
+			status = "disabled";
+			ti,hwmods = "dss_core";
+			clocks = <&disp_clk>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			dispc: dispc@4832a400 {
+				compatible = "ti,omap3-dispc";
+				reg = <0x4832a400 0x400>;
+				interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>;
+				ti,hwmods = "dss_dispc";
+				clocks = <&disp_clk>;
+				clock-names = "fck";
+			};
+
+			rfbi: rfbi@4832a800 {
+				compatible = "ti,omap3-rfbi";
+				reg = <0x4832a800 0x100>;
+				ti,hwmods = "dss_rfbi";
+				clocks = <&disp_clk>;
+				clock-names = "fck";
+				status = "disabled";
+			};
+		};
+
+		ocmcram: ocmcram@40300000 {
+			compatible = "mmio-sram";
+			reg = <0x40300000 0x40000>; /* 256k */
+		};
+
+		dcan0: can@481cc000 {
+			compatible = "ti,am4372-d_can", "ti,am3352-d_can";
+			ti,hwmods = "d_can0";
+			clocks = <&dcan0_fck>;
+			clock-names = "fck";
+			reg = <0x481cc000 0x2000>;
+			syscon-raminit = <&scm_conf 0x644 0>;
+			interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		dcan1: can@481d0000 {
+			compatible = "ti,am4372-d_can", "ti,am3352-d_can";
+			ti,hwmods = "d_can1";
+			clocks = <&dcan1_fck>;
+			clock-names = "fck";
+			reg = <0x481d0000 0x2000>;
+			syscon-raminit = <&scm_conf 0x644 1>;
+			interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		vpfe0: vpfe@48326000 {
+			compatible = "ti,am437x-vpfe";
+			reg = <0x48326000 0x2000>;
+			interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "vpfe0";
+			status = "disabled";
+		};
+
+		vpfe1: vpfe@48328000 {
+			compatible = "ti,am437x-vpfe";
+			reg = <0x48328000 0x2000>;
+			interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "vpfe1";
+			status = "disabled";
+		};
+	};
+};
+
+/include/ "am43xx-clocks.dtsi"

arch/arm/dts/am437x-gp-evm.dts

@@ -0,0 +1,797 @@
+/*
+ * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/* AM437x GP EVM */
+
+/dts-v1/;
+
+#include "am4372.dtsi"
+#include <dt-bindings/pinctrl/am43xx.h>
+#include <dt-bindings/pwm/pwm.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "TI AM437x GP EVM";
+	compatible = "ti,am437x-gp-evm","ti,am4372","ti,am43";
+
+	aliases {
+		display0 = &lcd0;
+		serial3 = &uart3;
+	};
+
+	chosen {
+		stdout-path = &uart0;
+	};
+
+	vmmcsd_fixed: fixedregulator-sd {
+		compatible = "regulator-fixed";
+		regulator-name = "vmmcsd_fixed";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+	};
+
+	vtt_fixed: fixedregulator-vtt {
+		compatible = "regulator-fixed";
+		regulator-name = "vtt_fixed";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+		regulator-always-on;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&gpio5 7 GPIO_ACTIVE_HIGH>;
+	};
+
+	vmmcwl_fixed: fixedregulator-mmcwl {
+		compatible = "regulator-fixed";
+		regulator-name = "vmmcwl_fixed";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&gpio1 20 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&ecap0 0 50000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <0 51 53 56 62 75 101 152 255>;
+		default-brightness-level = <8>;
+	};
+
+	matrix_keypad: matrix_keypad@0 {
+		compatible = "gpio-matrix-keypad";
+		debounce-delay-ms = <5>;
+		col-scan-delay-us = <2>;
+
+		row-gpios = <&gpio3 21 GPIO_ACTIVE_HIGH /* Bank3, pin21 */
+				&gpio4 3 GPIO_ACTIVE_HIGH /* Bank4, pin3 */
+				&gpio4 2 GPIO_ACTIVE_HIGH>; /* Bank4, pin2 */
+
+		col-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH /* Bank3, pin19 */
+				&gpio3 20 GPIO_ACTIVE_HIGH>; /* Bank3, pin20 */
+
+		linux,keymap = <0x00000201      /* P1 */
+				0x00010202      /* P2 */
+				0x01000067      /* UP */
+				0x0101006a      /* RIGHT */
+				0x02000069      /* LEFT */
+				0x0201006c>;      /* DOWN */
+		};
+
+	lcd0: display {
+		compatible = "osddisplays,osd057T0559-34ts", "panel-dpi";
+		label = "lcd";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_pins>;
+
+		/*
+		 * SelLCDorHDMI, LOW to select HDMI. This is not really the
+		 * panel's enable GPIO, but we don't have HDMI driver support nor
+		 * support to switch between two displays, so using this gpio as
+		 * panel's enable should be safe.
+		 */
+		enable-gpios = <&gpio5 8 GPIO_ACTIVE_HIGH>;
+
+		panel-timing {
+			clock-frequency = <33000000>;
+			hactive = <800>;
+			vactive = <480>;
+			hfront-porch = <210>;
+			hback-porch = <16>;
+			hsync-len = <30>;
+			vback-porch = <10>;
+			vfront-porch = <22>;
+			vsync-len = <13>;
+			hsync-active = <0>;
+			vsync-active = <0>;
+			de-active = <1>;
+			pixelclk-active = <1>;
+		};
+
+		port {
+			lcd_in: endpoint {
+				remote-endpoint = <&dpi_out>;
+			};
+		};
+	};
+
+	/* fixed 12MHz oscillator */
+	refclk: oscillator {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <12000000>;
+	};
+
+};
+
+&am43xx_pinmux {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&wlan_pins_default>;
+	pinctrl-1 = <&wlan_pins_sleep>;
+
+	i2c0_pins: i2c0_pins {
+		pinctrl-single,pins = <
+			0x188 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)  /* i2c0_sda.i2c0_sda */
+			0x18c (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)  /* i2c0_scl.i2c0_scl */
+		>;
+	};
+
+	i2c1_pins: i2c1_pins {
+		pinctrl-single,pins = <
+			0x15c (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE2)  /* spi0_cs0.i2c1_scl */
+			0x158 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE2)  /* spi0_d1.i2c1_sda  */
+		>;
+	};
+
+	mmc1_pins: pinmux_mmc1_pins {
+		pinctrl-single,pins = <
+			0x160 (PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */
+		>;
+	};
+
+	ecap0_pins: backlight_pins {
+		pinctrl-single,pins = <
+			0x164 MUX_MODE0       /* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out MODE0 */
+		>;
+	};
+
+	pixcir_ts_pins: pixcir_ts_pins {
+		pinctrl-single,pins = <
+			0x264 (PIN_INPUT_PULLUP | MUX_MODE7)  /* spi2_d0.gpio3_22 */
+		>;
+	};
+
+	cpsw_default: cpsw_default {
+		pinctrl-single,pins = <
+			/* Slave 1 */
+			0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* mii1_txen.rgmii1_txen */
+			0x118 (PIN_INPUT_PULLDOWN | MUX_MODE2)	/* mii1_rxdv.rgmii1_rxctl */
+			0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* mii1_txd1.rgmii1_txd3 */
+			0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* mii1_txd0.rgmii1_txd2 */
+			0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* mii1_txd1.rgmii1_txd1 */
+			0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* mii1_txd0.rgmii1_txd0 */
+			0x12c (PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* mii1_txclk.rmii1_tclk */
+			0x130 (PIN_INPUT_PULLDOWN | MUX_MODE2)	/* mii1_rxclk.rmii1_rclk */
+			0x134 (PIN_INPUT_PULLDOWN | MUX_MODE2)	/* mii1_rxd1.rgmii1_rxd3 */
+			0x138 (PIN_INPUT_PULLDOWN | MUX_MODE2)	/* mii1_rxd0.rgmii1_rxd2 */
+			0x13c (PIN_INPUT_PULLDOWN | MUX_MODE2)	/* mii1_rxd1.rgmii1_rxd1 */
+			0x140 (PIN_INPUT_PULLDOWN | MUX_MODE2)	/* mii1_rxd0.rgmii1_rxd0 */
+		>;
+	};
+
+	cpsw_sleep: cpsw_sleep {
+		pinctrl-single,pins = <
+			/* Slave 1 reset value */
+			0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+		>;
+	};
+
+	davinci_mdio_default: davinci_mdio_default {
+		pinctrl-single,pins = <
+			/* MDIO */
+			0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)	/* mdio_data.mdio_data */
+			0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0)			/* mdio_clk.mdio_clk */
+		>;
+	};
+
+	davinci_mdio_sleep: davinci_mdio_sleep {
+		pinctrl-single,pins = <
+			/* MDIO reset value */
+			0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+		>;
+	};
+
+	nand_flash_x8: nand_flash_x8 {
+		pinctrl-single,pins = <
+			0x26c(PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* spi2_cs0.gpio/eMMCorNANDsel */
+			0x0  (PIN_INPUT  | MUX_MODE0)	/* gpmc_ad0.gpmc_ad0 */
+			0x4  (PIN_INPUT  | MUX_MODE0)	/* gpmc_ad1.gpmc_ad1 */
+			0x8  (PIN_INPUT  | MUX_MODE0)	/* gpmc_ad2.gpmc_ad2 */
+			0xc  (PIN_INPUT  | MUX_MODE0)	/* gpmc_ad3.gpmc_ad3 */
+			0x10 (PIN_INPUT  | MUX_MODE0)	/* gpmc_ad4.gpmc_ad4 */
+			0x14 (PIN_INPUT  | MUX_MODE0)	/* gpmc_ad5.gpmc_ad5 */
+			0x18 (PIN_INPUT  | MUX_MODE0)	/* gpmc_ad6.gpmc_ad6 */
+			0x1c (PIN_INPUT  | MUX_MODE0)	/* gpmc_ad7.gpmc_ad7 */
+			0x70 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_wait0.gpmc_wait0 */
+			0x74 (PIN_OUTPUT_PULLUP | MUX_MODE7)	/* gpmc_wpn.gpmc_wpn */
+			0x7c (PIN_OUTPUT | MUX_MODE0)		/* gpmc_csn0.gpmc_csn0  */
+			0x90 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_advn_ale.gpmc_advn_ale */
+			0x94 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_oen_ren.gpmc_oen_ren */
+			0x98 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_wen.gpmc_wen */
+			0x9c (PIN_OUTPUT | MUX_MODE0)		/* gpmc_be0n_cle.gpmc_be0n_cle */
+		>;
+	};
+
+	dss_pins: dss_pins {
+		pinctrl-single,pins = <
+			0x020 (PIN_OUTPUT_PULLUP | MUX_MODE1) /*gpmc ad 8 -> DSS DATA 23 */
+			0x024 (PIN_OUTPUT_PULLUP | MUX_MODE1)
+			0x028 (PIN_OUTPUT_PULLUP | MUX_MODE1)
+			0x02c (PIN_OUTPUT_PULLUP | MUX_MODE1)
+			0x030 (PIN_OUTPUT_PULLUP | MUX_MODE1)
+			0x034 (PIN_OUTPUT_PULLUP | MUX_MODE1)
+			0x038 (PIN_OUTPUT_PULLUP | MUX_MODE1)
+			0x03c (PIN_OUTPUT_PULLUP | MUX_MODE1) /*gpmc ad 15 -> DSS DATA 16 */
+			0x0a0 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* DSS DATA 0 */
+			0x0a4 (PIN_OUTPUT_PULLUP | MUX_MODE0)
+			0x0a8 (PIN_OUTPUT_PULLUP | MUX_MODE0)
+			0x0ac (PIN_OUTPUT_PULLUP | MUX_MODE0)
+			0x0b0 (PIN_OUTPUT_PULLUP | MUX_MODE0)
+			0x0b4 (PIN_OUTPUT_PULLUP | MUX_MODE0)
+			0x0b8 (PIN_OUTPUT_PULLUP | MUX_MODE0)
+			0x0bc (PIN_OUTPUT_PULLUP | MUX_MODE0)
+			0x0c0 (PIN_OUTPUT_PULLUP | MUX_MODE0)
+			0x0c4 (PIN_OUTPUT_PULLUP | MUX_MODE0)
+			0x0c8 (PIN_OUTPUT_PULLUP | MUX_MODE0)
+			0x0cc (PIN_OUTPUT_PULLUP | MUX_MODE0)
+			0x0d0 (PIN_OUTPUT_PULLUP | MUX_MODE0)
+			0x0d4 (PIN_OUTPUT_PULLUP | MUX_MODE0)
+			0x0d8 (PIN_OUTPUT_PULLUP | MUX_MODE0)
+			0x0dc (PIN_OUTPUT_PULLUP | MUX_MODE0) /* DSS DATA 15 */
+			0x0e0 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* DSS VSYNC */
+			0x0e4 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* DSS HSYNC */
+			0x0e8 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* DSS PCLK */
+			0x0ec (PIN_OUTPUT_PULLUP | MUX_MODE0) /* DSS AC BIAS EN */
+
+		>;
+	};
+
+	lcd_pins: lcd_pins {
+		pinctrl-single,pins = <
+			/* GPIO 5_8 to select LCD / HDMI */
+			0x238 (PIN_OUTPUT_PULLUP | MUX_MODE7)
+		>;
+	};
+
+	dcan0_default: dcan0_default_pins {
+		pinctrl-single,pins = <
+			0x178 (PIN_OUTPUT | MUX_MODE2)		/* uart1_ctsn.d_can0_tx */
+			0x17c (PIN_INPUT_PULLUP | MUX_MODE2)	/* uart1_rtsn.d_can0_rx */
+		>;
+	};
+
+	dcan1_default: dcan1_default_pins {
+		pinctrl-single,pins = <
+			0x180 (PIN_OUTPUT | MUX_MODE2)		/* uart1_rxd.d_can1_tx */
+			0x184 (PIN_INPUT_PULLUP | MUX_MODE2)	/* uart1_txd.d_can1_rx */
+		>;
+	};
+
+	vpfe0_pins_default: vpfe0_pins_default {
+		pinctrl-single,pins = <
+			0x1B0 (PIN_INPUT_PULLUP | MUX_MODE0)  /* cam0_hd mode 0*/
+			0x1B4 (PIN_INPUT_PULLUP | MUX_MODE0)  /* cam0_vd mode 0*/
+			0x1C0 (PIN_INPUT_PULLUP | MUX_MODE0)  /* cam0_pclk mode 0*/
+			0x1C4 (PIN_INPUT_PULLUP | MUX_MODE0)  /* cam0_data8 mode 0*/
+			0x1C8 (PIN_INPUT_PULLUP | MUX_MODE0)  /* cam0_data9 mode 0*/
+			0x208 (PIN_INPUT_PULLUP | MUX_MODE0)  /* cam0_data0 mode 0*/
+			0x20C (PIN_INPUT_PULLUP | MUX_MODE0)  /* cam0_data1 mode 0*/
+			0x210 (PIN_INPUT_PULLUP | MUX_MODE0)  /* cam0_data2 mode 0*/
+			0x214 (PIN_INPUT_PULLUP | MUX_MODE0)  /* cam0_data3 mode 0*/
+			0x218 (PIN_INPUT_PULLUP | MUX_MODE0)  /* cam0_data4 mode 0*/
+			0x21C (PIN_INPUT_PULLUP | MUX_MODE0)  /* cam0_data5 mode 0*/
+			0x220 (PIN_INPUT_PULLUP | MUX_MODE0)  /* cam0_data6 mode 0*/
+			0x224 (PIN_INPUT_PULLUP | MUX_MODE0)  /* cam0_data7 mode 0*/
+		>;
+	};
+
+	vpfe0_pins_sleep: vpfe0_pins_sleep {
+		pinctrl-single,pins = <
+			0x1B0 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)  /* cam0_hd mode 0*/
+			0x1B4 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)  /* cam0_vd mode 0*/
+			0x1C0 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)  /* cam0_pclk mode 0*/
+			0x1C4 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)  /* cam0_data8 mode 0*/
+			0x1C8 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)  /* cam0_data9 mode 0*/
+			0x208 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)  /* cam0_data0 mode 0*/
+			0x20C (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)  /* cam0_data1 mode 0*/
+			0x210 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)  /* cam0_data2 mode 0*/
+			0x214 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)  /* cam0_data3 mode 0*/
+			0x218 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)  /* cam0_data4 mode 0*/
+			0x21C (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)  /* cam0_data5 mode 0*/
+			0x220 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)  /* cam0_data6 mode 0*/
+			0x224 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)  /* cam0_data7 mode 0*/
+		>;
+	};
+
+	vpfe1_pins_default: vpfe1_pins_default {
+		pinctrl-single,pins = <
+			0x1CC (PIN_INPUT_PULLUP | MUX_MODE0)  /* cam1_data9 mode 0*/
+			0x1D0 (PIN_INPUT_PULLUP | MUX_MODE0)  /* cam1_data8 mode 0*/
+			0x1D4 (PIN_INPUT_PULLUP | MUX_MODE0)  /* cam1_hd mode 0*/
+			0x1D8 (PIN_INPUT_PULLUP | MUX_MODE0)  /* cam1_vd mode 0*/
+			0x1DC (PIN_INPUT_PULLUP | MUX_MODE0)  /* cam1_pclk mode 0*/
+			0x1E8 (PIN_INPUT_PULLUP | MUX_MODE0)  /* cam1_data0 mode 0*/
+			0x1EC (PIN_INPUT_PULLUP | MUX_MODE0)  /* cam1_data1 mode 0*/
+			0x1F0 (PIN_INPUT_PULLUP | MUX_MODE0)  /* cam1_data2 mode 0*/
+			0x1F4 (PIN_INPUT_PULLUP | MUX_MODE0)  /* cam1_data3 mode 0*/
+			0x1F8 (PIN_INPUT_PULLUP | MUX_MODE0)  /* cam1_data4 mode 0*/
+			0x1FC (PIN_INPUT_PULLUP | MUX_MODE0)  /* cam1_data5 mode 0*/
+			0x200 (PIN_INPUT_PULLUP | MUX_MODE0)  /* cam1_data6 mode 0*/
+			0x204 (PIN_INPUT_PULLUP | MUX_MODE0)  /* cam1_data7 mode 0*/
+		>;
+	};
+
+	vpfe1_pins_sleep: vpfe1_pins_sleep {
+		pinctrl-single,pins = <
+			0x1CC (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)  /* cam1_data9 mode 0*/
+			0x1D0 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)  /* cam1_data8 mode 0*/
+			0x1D4 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)  /* cam1_hd mode 0*/
+			0x1D8 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)  /* cam1_vd mode 0*/
+			0x1DC (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)  /* cam1_pclk mode 0*/
+			0x1E8 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)  /* cam1_data0 mode 0*/
+			0x1EC (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)  /* cam1_data1 mode 0*/
+			0x1F0 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)  /* cam1_data2 mode 0*/
+			0x1F4 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)  /* cam1_data3 mode 0*/
+			0x1F8 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)  /* cam1_data4 mode 0*/
+			0x1FC (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)  /* cam1_data5 mode 0*/
+			0x200 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)  /* cam1_data6 mode 0*/
+			0x204 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)  /* cam1_data7 mode 0*/
+		>;
+	};
+
+	mmc3_pins_default: pinmux_mmc3_pins_default {
+		pinctrl-single,pins = <
+			0x8c (PIN_INPUT_PULLUP | MUX_MODE3)      /* gpmc_clk.mmc2_clk */
+			0x88 (PIN_INPUT_PULLUP | MUX_MODE3)      /* gpmc_csn3.mmc2_cmd */
+			0x44 (PIN_INPUT_PULLUP | MUX_MODE3)      /* gpmc_a1.mmc2_dat0 */
+			0x48 (PIN_INPUT_PULLUP | MUX_MODE3)      /* gpmc_a2.mmc2_dat1 */
+			0x4c (PIN_INPUT_PULLUP | MUX_MODE3)      /* gpmc_a3.mmc2_dat2 */
+			0x78 (PIN_INPUT_PULLUP | MUX_MODE3)      /* gpmc_be1n.mmc2_dat3 */
+		>;
+	};
+
+	mmc3_pins_sleep: pinmux_mmc3_pins_sleep {
+		pinctrl-single,pins = <
+			0x8c (PIN_INPUT_PULLDOWN | MUX_MODE7)	/* gpmc_clk.mmc2_clk */
+			0x88 (PIN_INPUT_PULLDOWN | MUX_MODE7)	/* gpmc_csn3.mmc2_cmd */
+			0x44 (PIN_INPUT_PULLDOWN | MUX_MODE7)	/* gpmc_a1.mmc2_dat0 */
+			0x48 (PIN_INPUT_PULLDOWN | MUX_MODE7)	/* gpmc_a2.mmc2_dat1 */
+			0x4c (PIN_INPUT_PULLDOWN | MUX_MODE7)	/* gpmc_a3.mmc2_dat2 */
+			0x78 (PIN_INPUT_PULLDOWN | MUX_MODE7)	/* gpmc_be1n.mmc2_dat3 */
+		>;
+	};
+
+	wlan_pins_default: pinmux_wlan_pins_default {
+		pinctrl-single,pins = <
+			0x50 (PIN_OUTPUT_PULLDOWN | MUX_MODE7)		/* gpmc_a4.gpio1_20 WL_EN */
+			0x5c (PIN_INPUT | WAKEUP_ENABLE | MUX_MODE7)	/* gpmc_a7.gpio1_23 WL_IRQ*/
+			0x40 (PIN_OUTPUT_PULLDOWN | MUX_MODE7)		/* gpmc_a0.gpio1_16 BT_EN*/
+		>;
+	};
+
+	wlan_pins_sleep: pinmux_wlan_pins_sleep {
+		pinctrl-single,pins = <
+			0x50 (PIN_OUTPUT_PULLDOWN | MUX_MODE7)		/* gpmc_a4.gpio1_20 WL_EN */
+			0x5c (PIN_INPUT | WAKEUP_ENABLE | MUX_MODE7)	/* gpmc_a7.gpio1_23 WL_IRQ*/
+			0x40 (PIN_OUTPUT_PULLUP | MUX_MODE7)		/* gpmc_a0.gpio1_16 BT_EN*/
+		>;
+	};
+
+	uart3_pins: uart3_pins {
+		pinctrl-single,pins = <
+			0x228 (PIN_INPUT | MUX_MODE0)		/* uart3_rxd.uart3_rxd */
+			0x22c (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart3_txd.uart3_txd */
+			0x230 (PIN_INPUT_PULLUP | MUX_MODE0)	/* uart3_ctsn.uart3_ctsn */
+			0x234 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart3_rtsn.uart3_rtsn */
+		>;
+	};
+};
+
+&i2c0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	clock-frequency = <100000>;
+
+	tps65218: tps65218@24 {
+		reg = <0x24>;
+		compatible = "ti,tps65218";
+		interrupts = <GIC_SPI 7 IRQ_TYPE_NONE>; /* NMIn */
+		interrupt-controller;
+		#interrupt-cells = <2>;
+
+		dcdc1: regulator-dcdc1 {
+			compatible = "ti,tps65218-dcdc1";
+			regulator-name = "vdd_core";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <1144000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		dcdc2: regulator-dcdc2 {
+			compatible = "ti,tps65218-dcdc2";
+			regulator-name = "vdd_mpu";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <1378000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		dcdc3: regulator-dcdc3 {
+			compatible = "ti,tps65218-dcdc3";
+			regulator-name = "vdcdc3";
+			regulator-min-microvolt = <1500000>;
+			regulator-max-microvolt = <1500000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+		dcdc5: regulator-dcdc5 {
+			compatible = "ti,tps65218-dcdc5";
+			regulator-name = "v1_0bat";
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1000000>;
+		};
+
+		dcdc6: regulator-dcdc6 {
+			compatible = "ti,tps65218-dcdc6";
+			regulator-name = "v1_8bat";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		ldo1: regulator-ldo1 {
+			compatible = "ti,tps65218-ldo1";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+	};
+
+	ov2659@30 {
+		compatible = "ovti,ov2659";
+		reg = <0x30>;
+
+		clocks = <&refclk 0>;
+		clock-names = "xvclk";
+
+		port {
+			ov2659_0: endpoint {
+				remote-endpoint = <&vpfe1_ep>;
+				link-frequencies = /bits/ 64 <70000000>;
+			};
+		};
+	};
+};
+
+&i2c1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	pixcir_ts@5c {
+		compatible = "pixcir,pixcir_tangoc";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pixcir_ts_pins>;
+		reg = <0x5c>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <22 0>;
+
+		attb-gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+
+		touchscreen-size-x = <1024>;
+		touchscreen-size-y = <600>;
+	};
+
+	ov2659@30 {
+		compatible = "ovti,ov2659";
+		reg = <0x30>;
+
+		clocks = <&refclk 0>;
+		clock-names = "xvclk";
+
+		port {
+			ov2659_1: endpoint {
+				remote-endpoint = <&vpfe0_ep>;
+				link-frequencies = /bits/ 64 <70000000>;
+			};
+		};
+	};
+};
+
+&epwmss0 {
+	status = "okay";
+};
+
+&tscadc {
+	status = "okay";
+
+	adc {
+		ti,adc-channels = <0 1 2 3 4 5 6 7>;
+	};
+};
+
+&ecap0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&ecap0_pins>;
+};
+
+&gpio0 {
+	status = "okay";
+};
+
+&gpio1 {
+	status = "okay";
+};
+
+&gpio3 {
+	status = "okay";
+};
+
+&gpio4 {
+	status = "okay";
+};
+
+&gpio5 {
+	status = "okay";
+	ti,no-reset-on-init;
+};
+
+&mmc1 {
+	status = "okay";
+	vmmc-supply = <&vmmcsd_fixed>;
+	bus-width = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
+};
+
+&mmc3 {
+	/* disable MMC3 as SDIO is not supported in U-Boot */
+	status = "disabled";
+	/* these are on the crossbar and are outlined in the
+	   xbar-event-map element */
+	dmas = <&edma 30
+		&edma 31>;
+	dma-names = "tx", "rx";
+	vmmc-supply = <&vmmcwl_fixed>;
+	bus-width = <4>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&mmc3_pins_default>;
+	pinctrl-1 = <&mmc3_pins_sleep>;
+	cap-power-off-card;
+	keep-power-in-suspend;
+	ti,non-removable;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+	wlcore: wlcore@0 {
+		compatible = "ti,wl1835";
+		reg = <2>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <23 IRQ_TYPE_LEVEL_HIGH>;
+	};
+};
+
+&edma {
+	ti,edma-xbar-event-map = /bits/ 16 <1 30
+					    2 31>;
+};
+
+&uart3 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>;
+};
+
+&usb2_phy1 {
+	status = "okay";
+};
+
+&usb1 {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usb2_phy2 {
+	status = "okay";
+};
+
+&usb2 {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&mac {
+	slaves = <1>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&cpsw_default>;
+	pinctrl-1 = <&cpsw_sleep>;
+	status = "okay";
+};
+
+&davinci_mdio {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&davinci_mdio_default>;
+	pinctrl-1 = <&davinci_mdio_sleep>;
+	status = "okay";
+};
+
+&cpsw_emac0 {
+	phy_id = <&davinci_mdio>, <0>;
+	phy-mode = "rgmii";
+};
+
+&elm {
+	status = "okay";
+};
+
+&gpmc {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&nand_flash_x8>;
+	ranges = <0 0 0 0x01000000>;	/* minimum GPMC partition = 16MB */
+	nand@0,0 {
+		reg = <0 0 4>;		/* device IO registers */
+		ti,nand-ecc-opt = "bch16";
+		ti,elm-id = <&elm>;
+		nand-bus-width = <8>;
+		gpmc,device-width = <1>;
+		gpmc,sync-clk-ps = <0>;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <40>;
+		gpmc,cs-wr-off-ns = <40>;
+		gpmc,adv-on-ns = <0>;
+		gpmc,adv-rd-off-ns = <25>;
+		gpmc,adv-wr-off-ns = <25>;
+		gpmc,we-on-ns = <0>;
+		gpmc,we-off-ns = <20>;
+		gpmc,oe-on-ns = <3>;
+		gpmc,oe-off-ns = <30>;
+		gpmc,access-ns = <30>;
+		gpmc,rd-cycle-ns = <40>;
+		gpmc,wr-cycle-ns = <40>;
+		gpmc,wait-pin = <0>;
+		gpmc,bus-turnaround-ns = <0>;
+		gpmc,cycle2cycle-delay-ns = <0>;
+		gpmc,clk-activation-ns = <0>;
+		gpmc,wait-monitoring-ns = <0>;
+		gpmc,wr-access-ns = <40>;
+		gpmc,wr-data-mux-bus-ns = <0>;
+		/* MTD partition table */
+		/* All SPL-* partitions are sized to minimal length
+		 * which can be independently programmable. For
+		 * NAND flash this is equal to size of erase-block */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		partition@0 {
+			label = "NAND.SPL";
+			reg = <0x00000000 0x00040000>;
+		};
+		partition@1 {
+			label = "NAND.SPL.backup1";
+			reg = <0x00040000 0x00040000>;
+		};
+		partition@2 {
+			label = "NAND.SPL.backup2";
+			reg = <0x00080000 0x00040000>;
+		};
+		partition@3 {
+			label = "NAND.SPL.backup3";
+			reg = <0x000c0000 0x00040000>;
+		};
+		partition@4 {
+			label = "NAND.u-boot-spl-os";
+			reg = <0x00100000 0x00080000>;
+		};
+		partition@5 {
+			label = "NAND.u-boot";
+			reg = <0x00180000 0x00100000>;
+		};
+		partition@6 {
+			label = "NAND.u-boot-env";
+			reg = <0x00280000 0x00040000>;
+		};
+		partition@7 {
+			label = "NAND.u-boot-env.backup1";
+			reg = <0x002c0000 0x00040000>;
+		};
+		partition@8 {
+			label = "NAND.kernel";
+			reg = <0x00300000 0x00700000>;
+		};
+		partition@9 {
+			label = "NAND.file-system";
+			reg = <0x00a00000 0x1f600000>;
+		};
+	};
+};
+
+&dss {
+	status = "ok";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&dss_pins>;
+
+	port {
+		dpi_out: endpoint@0 {
+			remote-endpoint = <&lcd_in>;
+			data-lines = <24>;
+		};
+	};
+};
+
+&dcan0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&dcan0_default>;
+	status = "okay";
+};
+
+&dcan1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&dcan1_default>;
+	status = "okay";
+};
+
+&vpfe0 {
+	status = "okay";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&vpfe0_pins_default>;
+	pinctrl-1 = <&vpfe0_pins_sleep>;
+
+	port {
+		vpfe0_ep: endpoint {
+			remote-endpoint = <&ov2659_1>;
+			ti,am437x-vpfe-interface = <0>;
+			bus-width = <8>;
+			hsync-active = <0>;
+			vsync-active = <0>;
+		};
+	};
+};
+
+&vpfe1 {
+	status = "okay";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&vpfe1_pins_default>;
+	pinctrl-1 = <&vpfe1_pins_sleep>;
+
+	port {
+		vpfe1_ep: endpoint {
+			remote-endpoint = <&ov2659_0>;
+			ti,am437x-vpfe-interface = <0>;
+			bus-width = <8>;
+			hsync-active = <0>;
+			vsync-active = <0>;
+		};
+	};
+};

arch/arm/dts/am437x-sk-evm.dts

@@ -0,0 +1,704 @@
+/*
+ * Copyright (C) 2014 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/* AM437x SK EVM */
+
+/dts-v1/;
+
+#include "am4372.dtsi"
+#include <dt-bindings/pinctrl/am43xx.h>
+#include <dt-bindings/pwm/pwm.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "TI AM437x SK EVM";
+	compatible = "ti,am437x-sk-evm","ti,am4372","ti,am43";
+
+	aliases {
+		display0 = &lcd0;
+	};
+
+	chosen {
+		stdout-path = &uart0;
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&ecap0 0 50000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <0 51 53 56 62 75 101 152 255>;
+		default-brightness-level = <8>;
+	};
+
+	sound {
+		compatible = "ti,da830-evm-audio";
+		ti,model = "AM437x-SK-EVM";
+		ti,audio-codec = <&tlv320aic3106>;
+		ti,mcasp-controller = <&mcasp1>;
+		ti,codec-clock-rate = <24000000>;
+		ti,audio-routing =
+			"Headphone Jack",       "HPLOUT",
+			"Headphone Jack",       "HPROUT";
+	};
+
+	matrix_keypad: matrix_keypad@0 {
+		compatible = "gpio-matrix-keypad";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&matrix_keypad_pins>;
+
+		debounce-delay-ms = <5>;
+		col-scan-delay-us = <5>;
+
+		row-gpios = <&gpio5 5 GPIO_ACTIVE_HIGH		/* Bank5, pin5 */
+				&gpio5 6 GPIO_ACTIVE_HIGH>;	/* Bank5, pin6 */
+
+		col-gpios = <&gpio5 13 GPIO_ACTIVE_HIGH		/* Bank5, pin13 */
+				&gpio5 4 GPIO_ACTIVE_HIGH>;	/* Bank5, pin4 */
+
+		linux,keymap = <
+				MATRIX_KEY(0, 0, KEY_DOWN)
+				MATRIX_KEY(0, 1, KEY_RIGHT)
+				MATRIX_KEY(1, 0, KEY_LEFT)
+				MATRIX_KEY(1, 1, KEY_UP)
+			>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&leds_pins>;
+
+		led@0 {
+			label = "am437x-sk:red:heartbeat";
+			gpios = <&gpio5 0 GPIO_ACTIVE_HIGH>;	/* Bank 5, pin 0 */
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
+		};
+
+		led@1 {
+			label = "am437x-sk:green:mmc1";
+			gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;	/* Bank 5, pin 1 */
+			linux,default-trigger = "mmc0";
+			default-state = "off";
+		};
+
+		led@2 {
+			label = "am437x-sk:blue:cpu0";
+			gpios = <&gpio5 2 GPIO_ACTIVE_HIGH>;	/* Bank 5, pin 2 */
+			linux,default-trigger = "cpu0";
+			default-state = "off";
+		};
+
+		led@3 {
+			label = "am437x-sk:blue:usr3";
+			gpios = <&gpio5 3 GPIO_ACTIVE_HIGH>;	/* Bank 5, pin 3 */
+			default-state = "off";
+		};
+	};
+
+	lcd0: display {
+		compatible = "newhaven,nhd-4.3-480272ef-atxl", "panel-dpi";
+		label = "lcd";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_pins>;
+
+		enable-gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+
+		panel-timing {
+			clock-frequency = <9000000>;
+			hactive = <480>;
+			vactive = <272>;
+			hfront-porch = <2>;
+			hback-porch = <2>;
+			hsync-len = <41>;
+			vfront-porch = <2>;
+			vback-porch = <2>;
+			vsync-len = <10>;
+			hsync-active = <0>;
+			vsync-active = <0>;
+			de-active = <1>;
+			pixelclk-active = <1>;
+		};
+
+		port {
+			lcd_in: endpoint {
+				remote-endpoint = <&dpi_out>;
+			};
+		};
+	};
+};
+
+&am43xx_pinmux {
+	matrix_keypad_pins: matrix_keypad_pins {
+		pinctrl-single,pins = <
+			0x24c (PIN_OUTPUT | MUX_MODE7)	/* gpio5_13.gpio5_13 */
+			0x250 (PIN_OUTPUT | MUX_MODE7)	/* spi4_sclk.gpio5_4 */
+			0x254 (PIN_INPUT | MUX_MODE7)	/* spi4_d0.gpio5_5 */
+			0x258 (PIN_INPUT | MUX_MODE7)	/* spi4_d1.gpio5_5 */
+		>;
+	};
+
+	leds_pins: leds_pins {
+		pinctrl-single,pins = <
+			0x228 (PIN_OUTPUT | MUX_MODE7)	/* uart3_rxd.gpio5_2 */
+			0x22c (PIN_OUTPUT | MUX_MODE7)	/* uart3_txd.gpio5_3 */
+			0x230 (PIN_OUTPUT | MUX_MODE7)	/* uart3_ctsn.gpio5_0 */
+			0x234 (PIN_OUTPUT | MUX_MODE7)	/* uart3_rtsn.gpio5_1 */
+		>;
+	};
+
+	i2c0_pins: i2c0_pins {
+		pinctrl-single,pins = <
+			0x188 (PIN_INPUT | SLEWCTRL_FAST | MUX_MODE0)  /* i2c0_sda.i2c0_sda */
+			0x18c (PIN_INPUT | SLEWCTRL_FAST | MUX_MODE0)  /* i2c0_scl.i2c0_scl */
+		>;
+	};
+
+	i2c1_pins: i2c1_pins {
+		pinctrl-single,pins = <
+			0x15c (PIN_INPUT | SLEWCTRL_FAST | MUX_MODE2)  /* spi0_cs0.i2c1_scl */
+			0x158 (PIN_INPUT | SLEWCTRL_FAST | MUX_MODE2)  /* spi0_d1.i2c1_sda  */
+		>;
+	};
+
+	mmc1_pins: pinmux_mmc1_pins {
+		pinctrl-single,pins = <
+			0x0f0 (PIN_INPUT | MUX_MODE0) /* mmc0_dat3.mmc0_dat3 */
+			0x0f4 (PIN_INPUT | MUX_MODE0) /* mmc0_dat2.mmc0_dat2 */
+			0x0f8 (PIN_INPUT | MUX_MODE0) /* mmc0_dat1.mmc0_dat1 */
+			0x0fc (PIN_INPUT | MUX_MODE0) /* mmc0_dat0.mmc0_dat0 */
+			0x100 (PIN_INPUT | MUX_MODE0) /* mmc0_clk.mmc0_clk */
+			0x104 (PIN_INPUT | MUX_MODE0) /* mmc0_cmd.mmc0_cmd */
+			0x160 (PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */
+		>;
+	};
+
+	ecap0_pins: backlight_pins {
+		pinctrl-single,pins = <
+			0x164 (PIN_OUTPUT | MUX_MODE0) /* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out */
+		>;
+	};
+
+	edt_ft5306_ts_pins: edt_ft5306_ts_pins {
+		pinctrl-single,pins = <
+			0x74 (PIN_INPUT | MUX_MODE7)	/* gpmc_wpn.gpio0_31 */
+			0x78 (PIN_OUTPUT | MUX_MODE7)	/* gpmc_be1n.gpio1_28 */
+		>;
+	};
+
+	vpfe0_pins_default: vpfe0_pins_default {
+		pinctrl-single,pins = <
+			0x1b0 (PIN_INPUT_PULLUP | MUX_MODE0)  /* cam0_hd mode 0*/
+			0x1b4 (PIN_INPUT_PULLUP | MUX_MODE0)  /* cam0_vd mode 0*/
+			0x1b8 (PIN_INPUT_PULLUP | MUX_MODE0)  /* cam0_field mode 0*/
+			0x1bc (PIN_INPUT_PULLUP | MUX_MODE0)  /* cam0_wen mode 0*/
+			0x1c0 (PIN_INPUT_PULLUP | MUX_MODE0)  /* cam0_pclk mode 0*/
+			0x1c4 (PIN_INPUT_PULLUP | MUX_MODE0)  /* cam0_data8 mode 0*/
+			0x1c8 (PIN_INPUT_PULLUP | MUX_MODE0)  /* cam0_data9 mode 0*/
+			0x208 (PIN_INPUT_PULLUP | MUX_MODE0)  /* cam0_data0 mode 0*/
+			0x20c (PIN_INPUT_PULLUP | MUX_MODE0)  /* cam0_data1 mode 0*/
+			0x210 (PIN_INPUT_PULLUP | MUX_MODE0)  /* cam0_data2 mode 0*/
+			0x214 (PIN_INPUT_PULLUP | MUX_MODE0)  /* cam0_data3 mode 0*/
+			0x218 (PIN_INPUT_PULLUP | MUX_MODE0)  /* cam0_data4 mode 0*/
+			0x21c (PIN_INPUT_PULLUP | MUX_MODE0)  /* cam0_data5 mode 0*/
+			0x220 (PIN_INPUT_PULLUP | MUX_MODE0)  /* cam0_data6 mode 0*/
+			0x224 (PIN_INPUT_PULLUP | MUX_MODE0)  /* cam0_data7 mode 0*/
+		>;
+	};
+
+	vpfe0_pins_sleep: vpfe0_pins_sleep {
+		pinctrl-single,pins = <
+			0x1b0 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)
+			0x1b4 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)
+			0x1b8 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)
+			0x1bc (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)
+			0x1c0 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)
+			0x1c4 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)
+			0x1c8 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)
+			0x208 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)
+			0x20c (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)
+			0x210 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)
+			0x214 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)
+			0x218 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)
+			0x21c (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)
+			0x220 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)
+			0x224 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)
+		>;
+	};
+
+	cpsw_default: cpsw_default {
+		pinctrl-single,pins = <
+			/* Slave 1 */
+			0x12c (PIN_OUTPUT | MUX_MODE2)	/* mii1_txclk.rmii1_tclk */
+			0x114 (PIN_OUTPUT | MUX_MODE2)	/* mii1_txen.rgmii1_tctl */
+			0x128 (PIN_OUTPUT | MUX_MODE2)	/* mii1_txd0.rgmii1_td0 */
+			0x124 (PIN_OUTPUT | MUX_MODE2)	/* mii1_txd1.rgmii1_td1 */
+			0x120 (PIN_OUTPUT | MUX_MODE2)	/* mii1_txd0.rgmii1_td2 */
+			0x11c (PIN_OUTPUT | MUX_MODE2)	/* mii1_txd1.rgmii1_td3 */
+			0x130 (PIN_INPUT | MUX_MODE2)	/* mii1_rxclk.rmii1_rclk */
+			0x118 (PIN_INPUT | MUX_MODE2)	/* mii1_rxdv.rgmii1_rctl */
+			0x140 (PIN_INPUT | MUX_MODE2)	/* mii1_rxd0.rgmii1_rd0 */
+			0x13c (PIN_INPUT | MUX_MODE2)	/* mii1_rxd1.rgmii1_rd1 */
+			0x138 (PIN_INPUT | MUX_MODE2)	/* mii1_rxd0.rgmii1_rd2 */
+			0x134 (PIN_INPUT | MUX_MODE2)	/* mii1_rxd1.rgmii1_rd3 */
+
+			/* Slave 2 */
+			0x58 (PIN_OUTPUT | MUX_MODE2)	/* gpmc_a6.rgmii2_tclk */
+			0x40 (PIN_OUTPUT | MUX_MODE2)	/* gpmc_a0.rgmii2_tctl */
+			0x54 (PIN_OUTPUT | MUX_MODE2)	/* gpmc_a5.rgmii2_td0 */
+			0x50 (PIN_OUTPUT | MUX_MODE2)	/* gpmc_a4.rgmii2_td1 */
+			0x4c (PIN_OUTPUT | MUX_MODE2)	/* gpmc_a3.rgmii2_td2 */
+			0x48 (PIN_OUTPUT | MUX_MODE2)	/* gpmc_a2.rgmii2_td3 */
+			0x5c (PIN_INPUT | MUX_MODE2)	/* gpmc_a7.rgmii2_rclk */
+			0x44 (PIN_INPUT | MUX_MODE2)	/* gpmc_a1.rgmii2_rtcl */
+			0x6c (PIN_INPUT | MUX_MODE2)	/* gpmc_a11.rgmii2_rd0 */
+			0x68 (PIN_INPUT | MUX_MODE2)	/* gpmc_a10.rgmii2_rd1 */
+			0x64 (PIN_INPUT | MUX_MODE2)	/* gpmc_a9.rgmii2_rd2 */
+			0x60 (PIN_INPUT | MUX_MODE2)	/* gpmc_a8.rgmii2_rd3 */
+		>;
+	};
+
+	cpsw_sleep: cpsw_sleep {
+		pinctrl-single,pins = <
+			/* Slave 1 reset value */
+			0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+
+			/* Slave 2 reset value */
+			0x58 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x40 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x54 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x50 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x4c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x48 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x5c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x44 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x6c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x68 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x64 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x60 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+		>;
+	};
+
+	davinci_mdio_default: davinci_mdio_default {
+		pinctrl-single,pins = <
+			/* MDIO */
+			0x148 (PIN_INPUT | SLEWCTRL_FAST | MUX_MODE0)	/* mdio_data.mdio_data */
+			0x14c (PIN_OUTPUT | MUX_MODE0)			/* mdio_clk.mdio_clk */
+		>;
+	};
+
+	davinci_mdio_sleep: davinci_mdio_sleep {
+		pinctrl-single,pins = <
+			/* MDIO reset value */
+			0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+		>;
+	};
+
+	dss_pins: dss_pins {
+		pinctrl-single,pins = <
+			0x020 (PIN_OUTPUT | MUX_MODE1)	/* gpmc ad 8 -> DSS DATA 23 */
+			0x024 (PIN_OUTPUT | MUX_MODE1)
+			0x028 (PIN_OUTPUT | MUX_MODE1)
+			0x02c (PIN_OUTPUT | MUX_MODE1)
+			0x030 (PIN_OUTPUT | MUX_MODE1)
+			0x034 (PIN_OUTPUT | MUX_MODE1)
+			0x038 (PIN_OUTPUT | MUX_MODE1)
+			0x03c (PIN_OUTPUT | MUX_MODE1)	/* gpmc ad 15 -> DSS DATA 16 */
+			0x0a0 (PIN_OUTPUT | MUX_MODE0)	/* DSS DATA 0 */
+			0x0a4 (PIN_OUTPUT | MUX_MODE0)
+			0x0a8 (PIN_OUTPUT | MUX_MODE0)
+			0x0ac (PIN_OUTPUT | MUX_MODE0)
+			0x0b0 (PIN_OUTPUT | MUX_MODE0)
+			0x0b4 (PIN_OUTPUT | MUX_MODE0)
+			0x0b8 (PIN_OUTPUT | MUX_MODE0)
+			0x0bc (PIN_OUTPUT | MUX_MODE0)
+			0x0c0 (PIN_OUTPUT | MUX_MODE0)
+			0x0c4 (PIN_OUTPUT | MUX_MODE0)
+			0x0c8 (PIN_OUTPUT | MUX_MODE0)
+			0x0cc (PIN_OUTPUT | MUX_MODE0)
+			0x0d0 (PIN_OUTPUT | MUX_MODE0)
+			0x0d4 (PIN_OUTPUT | MUX_MODE0)
+			0x0d8 (PIN_OUTPUT | MUX_MODE0)
+			0x0dc (PIN_OUTPUT | MUX_MODE0)	/* DSS DATA 15 */
+			0x0e0 (PIN_OUTPUT | MUX_MODE0)	/* DSS VSYNC */
+			0x0e4 (PIN_OUTPUT | MUX_MODE0)	/* DSS HSYNC */
+			0x0e8 (PIN_OUTPUT | MUX_MODE0)	/* DSS PCLK */
+			0x0ec (PIN_OUTPUT | MUX_MODE0)	/* DSS AC BIAS EN */
+
+		>;
+	};
+
+	qspi_pins: qspi_pins {
+		pinctrl-single,pins = <
+			0x7c (PIN_OUTPUT | MUX_MODE3)	/* gpmc_csn0.qspi_csn */
+			0x88 (PIN_OUTPUT | MUX_MODE2)	/* gpmc_csn3.qspi_clk */
+			0x90 (PIN_INPUT | MUX_MODE3)	/* gpmc_advn_ale.qspi_d0 */
+			0x94 (PIN_INPUT | MUX_MODE3)	/* gpmc_oen_ren.qspi_d1 */
+			0x98 (PIN_INPUT | MUX_MODE3)	/* gpmc_wen.qspi_d2 */
+			0x9c (PIN_INPUT | MUX_MODE3)	/* gpmc_be0n_cle.qspi_d3 */
+		>;
+	};
+
+	mcasp1_pins: mcasp1_pins {
+		pinctrl-single,pins = <
+			0x10c (PIN_INPUT_PULLDOWN | MUX_MODE4)	/* mii1_crs.mcasp1_aclkx */
+			0x110 (PIN_INPUT_PULLDOWN | MUX_MODE4)	/* mii1_rxerr.mcasp1_fsx */
+			0x108 (PIN_OUTPUT_PULLDOWN | MUX_MODE4)	/* mii1_col.mcasp1_axr2 */
+			0x144 (PIN_INPUT_PULLDOWN | MUX_MODE4)	/* rmii1_ref_clk.mcasp1_axr3 */
+		>;
+	};
+
+	lcd_pins: lcd_pins {
+		pinctrl-single,pins = <
+			0x1c (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpcm_ad7.gpio1_7 */
+		>;
+	};
+
+	usb1_pins: usb1_pins {
+		pinctrl-single,pins = <
+			0x2c0 (PIN_OUTPUT | MUX_MODE0) /* usb0_drvvbus.usb0_drvvbus */
+		>;
+	};
+
+	usb2_pins: usb2_pins {
+		pinctrl-single,pins = <
+			0x2c4 (PIN_OUTPUT | MUX_MODE0) /* usb0_drvvbus.usb0_drvvbus */
+		>;
+	};
+};
+
+&i2c0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	clock-frequency = <400000>;
+
+	tps@24 {
+		compatible = "ti,tps65218";
+		reg = <0x24>;
+		interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+
+		dcdc1: regulator-dcdc1 {
+			compatible = "ti,tps65218-dcdc1";
+			/* VDD_CORE limits min of OPP50 and max of OPP100 */
+			regulator-name = "vdd_core";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <1144000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		dcdc2: regulator-dcdc2 {
+			compatible = "ti,tps65218-dcdc2";
+			/* VDD_MPU limits min of OPP50 and max of OPP_NITRO */
+			regulator-name = "vdd_mpu";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <1378000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		dcdc3: regulator-dcdc3 {
+			compatible = "ti,tps65218-dcdc3";
+			regulator-name = "vdds_ddr";
+			regulator-min-microvolt = <1500000>;
+			regulator-max-microvolt = <1500000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		dcdc4: regulator-dcdc4 {
+			compatible = "ti,tps65218-dcdc4";
+			regulator-name = "v3_3d";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		ldo1: regulator-ldo1 {
+			compatible = "ti,tps65218-ldo1";
+			regulator-name = "v1_8d";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		power-button {
+			compatible = "ti,tps65218-pwrbutton";
+			status = "okay";
+			interrupts = <3 IRQ_TYPE_EDGE_BOTH>;
+		};
+	};
+
+	at24@50 {
+		compatible = "at24,24c256";
+		pagesize = <64>;
+		reg = <0x50>;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <400000>;
+
+	edt-ft5306@38 {
+		status = "okay";
+		compatible = "edt,edt-ft5306", "edt,edt-ft5x06";
+		pinctrl-names = "default";
+		pinctrl-0 = <&edt_ft5306_ts_pins>;
+
+		reg = <0x38>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <31 0>;
+
+		reset-gpios = <&gpio1 28 GPIO_ACTIVE_LOW>;
+
+		touchscreen-size-x = <480>;
+		touchscreen-size-y = <272>;
+	};
+
+	tlv320aic3106: tlv320aic3106@1b {
+		compatible = "ti,tlv320aic3106";
+		reg = <0x1b>;
+		status = "okay";
+
+		/* Regulators */
+		AVDD-supply = <&dcdc4>;
+		IOVDD-supply = <&dcdc4>;
+		DRVDD-supply = <&dcdc4>;
+		DVDD-supply = <&ldo1>;
+	};
+
+	lis331dlh@18 {
+		compatible = "st,lis331dlh";
+		reg = <0x18>;
+		status = "okay";
+
+		Vdd-supply = <&dcdc4>;
+		Vdd_IO-supply = <&dcdc4>;
+		interrupts-extended = <&gpio1 6 0>, <&gpio2 1 0>;
+	};
+};
+
+&epwmss0 {
+	status = "okay";
+};
+
+&ecap0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&ecap0_pins>;
+};
+
+&gpio0 {
+	status = "okay";
+};
+
+&gpio1 {
+	status = "okay";
+};
+
+&gpio5 {
+	status = "okay";
+};
+
+&mmc1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+
+	vmmc-supply = <&dcdc4>;
+	bus-width = <4>;
+	cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
+};
+
+&usb2_phy1 {
+	status = "okay";
+};
+
+&usb1 {
+	dr_mode = "peripheral";
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb1_pins>;
+};
+
+&usb2_phy2 {
+	status = "okay";
+};
+
+&usb2 {
+	dr_mode = "host";
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb2_pins>;
+};
+
+&qspi {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&qspi_pins>;
+
+	spi-max-frequency = <48000000>;
+	m25p80@0 {
+		compatible = "mx66l51235l";
+		spi-max-frequency = <48000000>;
+		reg = <0>;
+		spi-cpol;
+		spi-cpha;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		/* MTD partition table.
+		 * The ROM checks the first 512KiB
+		 * for a valid file to boot(XIP).
+		 */
+		partition@0 {
+			label = "QSPI.U_BOOT";
+			reg = <0x00000000 0x000080000>;
+		};
+		partition@1 {
+			label = "QSPI.U_BOOT.backup";
+			reg = <0x00080000 0x00080000>;
+		};
+		partition@2 {
+			label = "QSPI.U-BOOT-SPL_OS";
+			reg = <0x00100000 0x00010000>;
+		};
+		partition@3 {
+			label = "QSPI.U_BOOT_ENV";
+			reg = <0x00110000 0x00010000>;
+		};
+		partition@4 {
+			label = "QSPI.U-BOOT-ENV.backup";
+			reg = <0x00120000 0x00010000>;
+		};
+		partition@5 {
+			label = "QSPI.KERNEL";
+			reg = <0x00130000 0x0800000>;
+		};
+		partition@6 {
+			label = "QSPI.FILESYSTEM";
+			reg = <0x00930000 0x36D0000>;
+		};
+	};
+};
+
+&mac {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&cpsw_default>;
+	pinctrl-1 = <&cpsw_sleep>;
+	dual_emac = <1>;
+	status = "okay";
+};
+
+&davinci_mdio {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&davinci_mdio_default>;
+	pinctrl-1 = <&davinci_mdio_sleep>;
+	status = "okay";
+};
+
+&cpsw_emac0 {
+	phy_id = <&davinci_mdio>, <4>;
+	phy-mode = "rgmii";
+	dual_emac_res_vlan = <1>;
+};
+
+&cpsw_emac1 {
+	phy_id = <&davinci_mdio>, <5>;
+	phy-mode = "rgmii";
+	dual_emac_res_vlan = <2>;
+};
+
+&elm {
+	status = "okay";
+};
+
+&mcasp1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcasp1_pins>;
+
+	status = "okay";
+
+	op-mode = <0>;
+	tdm-slots = <2>;
+	serial-dir = <
+		0 0 1 2
+	>;
+
+	tx-num-evt = <1>;
+	rx-num-evt = <1>;
+};
+
+&dss {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&dss_pins>;
+
+	port {
+		dpi_out: endpoint@0 {
+			remote-endpoint = <&lcd_in>;
+			data-lines = <24>;
+		};
+	};
+};
+
+&rtc {
+	status = "okay";
+};
+
+&wdt {
+	status = "okay";
+};
+
+&cpu {
+	cpu0-supply = <&dcdc2>;
+};
+
+&vpfe0 {
+	status = "okay";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&vpfe0_pins_default>;
+	pinctrl-1 = <&vpfe0_pins_sleep>;
+
+	/* Camera port */
+	port {
+		vpfe0_ep: endpoint {
+			/* remote-endpoint = <&sensor>; add once we have it */
+			ti,am437x-vpfe-interface = <0>;
+			bus-width = <8>;
+			hsync-active = <0>;
+			vsync-active = <0>;
+		};
+	};
+};

arch/arm/dts/am43xx-clocks.dtsi

@@ -0,0 +1,757 @@
+/*
+ * Device Tree Source for AM43xx clock data
+ *
+ * Copyright (C) 2013 Texas Instruments, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+&scm_clocks {
+	sys_clkin_ck: sys_clkin_ck {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&sysboot_freq_sel_ck>, <&crystal_freq_sel_ck>;
+		ti,bit-shift = <31>;
+		reg = <0x0040>;
+	};
+
+	crystal_freq_sel_ck: crystal_freq_sel_ck {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&virt_19200000_ck>, <&virt_24000000_ck>, <&virt_25000000_ck>, <&virt_26000000_ck>;
+		ti,bit-shift = <29>;
+		reg = <0x0040>;
+	};
+
+	sysboot_freq_sel_ck: sysboot_freq_sel_ck@44e10040 {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&virt_19200000_ck>, <&virt_24000000_ck>, <&virt_25000000_ck>, <&virt_26000000_ck>;
+		ti,bit-shift = <22>;
+		reg = <0x0040>;
+	};
+
+	adc_tsc_fck: adc_tsc_fck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&sys_clkin_ck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	dcan0_fck: dcan0_fck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&sys_clkin_ck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	dcan1_fck: dcan1_fck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&sys_clkin_ck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	mcasp0_fck: mcasp0_fck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&sys_clkin_ck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	mcasp1_fck: mcasp1_fck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&sys_clkin_ck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	smartreflex0_fck: smartreflex0_fck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&sys_clkin_ck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	smartreflex1_fck: smartreflex1_fck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&sys_clkin_ck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	sha0_fck: sha0_fck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&sys_clkin_ck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	aes0_fck: aes0_fck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&sys_clkin_ck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	ehrpwm0_tbclk: ehrpwm0_tbclk {
+		#clock-cells = <0>;
+		compatible = "ti,gate-clock";
+		clocks = <&l4ls_gclk>;
+		ti,bit-shift = <0>;
+		reg = <0x0664>;
+	};
+
+	ehrpwm1_tbclk: ehrpwm1_tbclk {
+		#clock-cells = <0>;
+		compatible = "ti,gate-clock";
+		clocks = <&l4ls_gclk>;
+		ti,bit-shift = <1>;
+		reg = <0x0664>;
+	};
+
+	ehrpwm2_tbclk: ehrpwm2_tbclk {
+		#clock-cells = <0>;
+		compatible = "ti,gate-clock";
+		clocks = <&l4ls_gclk>;
+		ti,bit-shift = <2>;
+		reg = <0x0664>;
+	};
+
+	ehrpwm3_tbclk: ehrpwm3_tbclk {
+		#clock-cells = <0>;
+		compatible = "ti,gate-clock";
+		clocks = <&l4ls_gclk>;
+		ti,bit-shift = <4>;
+		reg = <0x0664>;
+	};
+
+	ehrpwm4_tbclk: ehrpwm4_tbclk {
+		#clock-cells = <0>;
+		compatible = "ti,gate-clock";
+		clocks = <&l4ls_gclk>;
+		ti,bit-shift = <5>;
+		reg = <0x0664>;
+	};
+
+	ehrpwm5_tbclk: ehrpwm5_tbclk {
+		#clock-cells = <0>;
+		compatible = "ti,gate-clock";
+		clocks = <&l4ls_gclk>;
+		ti,bit-shift = <6>;
+		reg = <0x0664>;
+	};
+};
+&prcm_clocks {
+	clk_32768_ck: clk_32768_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <32768>;
+	};
+
+	clk_rc32k_ck: clk_rc32k_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <32768>;
+	};
+
+	virt_19200000_ck: virt_19200000_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <19200000>;
+	};
+
+	virt_24000000_ck: virt_24000000_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <24000000>;
+	};
+
+	virt_25000000_ck: virt_25000000_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <25000000>;
+	};
+
+	virt_26000000_ck: virt_26000000_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <26000000>;
+	};
+
+	tclkin_ck: tclkin_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <26000000>;
+	};
+
+	dpll_core_ck: dpll_core_ck {
+		#clock-cells = <0>;
+		compatible = "ti,am3-dpll-core-clock";
+		clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
+		reg = <0x2d20>, <0x2d24>, <0x2d2c>;
+	};
+
+	dpll_core_x2_ck: dpll_core_x2_ck {
+		#clock-cells = <0>;
+		compatible = "ti,am3-dpll-x2-clock";
+		clocks = <&dpll_core_ck>;
+	};
+
+	dpll_core_m4_ck: dpll_core_m4_ck {
+		#clock-cells = <0>;
+		compatible = "ti,divider-clock";
+		clocks = <&dpll_core_x2_ck>;
+		ti,max-div = <31>;
+		ti,autoidle-shift = <8>;
+		reg = <0x2d38>;
+		ti,index-starts-at-one;
+		ti,invert-autoidle-bit;
+	};
+
+	dpll_core_m5_ck: dpll_core_m5_ck {
+		#clock-cells = <0>;
+		compatible = "ti,divider-clock";
+		clocks = <&dpll_core_x2_ck>;
+		ti,max-div = <31>;
+		ti,autoidle-shift = <8>;
+		reg = <0x2d3c>;
+		ti,index-starts-at-one;
+		ti,invert-autoidle-bit;
+	};
+
+	dpll_core_m6_ck: dpll_core_m6_ck {
+		#clock-cells = <0>;
+		compatible = "ti,divider-clock";
+		clocks = <&dpll_core_x2_ck>;
+		ti,max-div = <31>;
+		ti,autoidle-shift = <8>;
+		reg = <0x2d40>;
+		ti,index-starts-at-one;
+		ti,invert-autoidle-bit;
+	};
+
+	dpll_mpu_ck: dpll_mpu_ck {
+		#clock-cells = <0>;
+		compatible = "ti,am3-dpll-clock";
+		clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
+		reg = <0x2d60>, <0x2d64>, <0x2d6c>;
+	};
+
+	dpll_mpu_m2_ck: dpll_mpu_m2_ck {
+		#clock-cells = <0>;
+		compatible = "ti,divider-clock";
+		clocks = <&dpll_mpu_ck>;
+		ti,max-div = <31>;
+		ti,autoidle-shift = <8>;
+		reg = <0x2d70>;
+		ti,index-starts-at-one;
+		ti,invert-autoidle-bit;
+	};
+
+	dpll_ddr_ck: dpll_ddr_ck {
+		#clock-cells = <0>;
+		compatible = "ti,am3-dpll-clock";
+		clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
+		reg = <0x2da0>, <0x2da4>, <0x2dac>;
+	};
+
+	dpll_ddr_m2_ck: dpll_ddr_m2_ck {
+		#clock-cells = <0>;
+		compatible = "ti,divider-clock";
+		clocks = <&dpll_ddr_ck>;
+		ti,max-div = <31>;
+		ti,autoidle-shift = <8>;
+		reg = <0x2db0>;
+		ti,index-starts-at-one;
+		ti,invert-autoidle-bit;
+	};
+
+	dpll_disp_ck: dpll_disp_ck {
+		#clock-cells = <0>;
+		compatible = "ti,am3-dpll-clock";
+		clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
+		reg = <0x2e20>, <0x2e24>, <0x2e2c>;
+	};
+
+	dpll_disp_m2_ck: dpll_disp_m2_ck {
+		#clock-cells = <0>;
+		compatible = "ti,divider-clock";
+		clocks = <&dpll_disp_ck>;
+		ti,max-div = <31>;
+		ti,autoidle-shift = <8>;
+		reg = <0x2e30>;
+		ti,index-starts-at-one;
+		ti,invert-autoidle-bit;
+		ti,set-rate-parent;
+	};
+
+	dpll_per_ck: dpll_per_ck {
+		#clock-cells = <0>;
+		compatible = "ti,am3-dpll-j-type-clock";
+		clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
+		reg = <0x2de0>, <0x2de4>, <0x2dec>;
+	};
+
+	dpll_per_m2_ck: dpll_per_m2_ck {
+		#clock-cells = <0>;
+		compatible = "ti,divider-clock";
+		clocks = <&dpll_per_ck>;
+		ti,max-div = <127>;
+		ti,autoidle-shift = <8>;
+		reg = <0x2df0>;
+		ti,index-starts-at-one;
+		ti,invert-autoidle-bit;
+	};
+
+	dpll_per_m2_div4_wkupdm_ck: dpll_per_m2_div4_wkupdm_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&dpll_per_m2_ck>;
+		clock-mult = <1>;
+		clock-div = <4>;
+	};
+
+	dpll_per_m2_div4_ck: dpll_per_m2_div4_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&dpll_per_m2_ck>;
+		clock-mult = <1>;
+		clock-div = <4>;
+	};
+
+	clk_24mhz: clk_24mhz {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&dpll_per_m2_ck>;
+		clock-mult = <1>;
+		clock-div = <8>;
+	};
+
+	clkdiv32k_ck: clkdiv32k_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&clk_24mhz>;
+		clock-mult = <1>;
+		clock-div = <732>;
+	};
+
+	clkdiv32k_ick: clkdiv32k_ick {
+		#clock-cells = <0>;
+		compatible = "ti,gate-clock";
+		clocks = <&clkdiv32k_ck>;
+		ti,bit-shift = <8>;
+		reg = <0x2a38>;
+	};
+
+	sysclk_div: sysclk_div {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&dpll_core_m4_ck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	pruss_ocp_gclk: pruss_ocp_gclk {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&sysclk_div>, <&dpll_disp_m2_ck>;
+		reg = <0x4248>;
+	};
+
+	clk_32k_tpm_ck: clk_32k_tpm_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <32768>;
+	};
+
+	timer1_fck: timer1_fck {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&sys_clkin_ck>, <&clkdiv32k_ick>, <&tclkin_ck>, <&clk_rc32k_ck>, <&clk_32768_ck>, <&clk_32k_tpm_ck>;
+		reg = <0x4200>;
+	};
+
+	timer2_fck: timer2_fck {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>;
+		reg = <0x4204>;
+	};
+
+	timer3_fck: timer3_fck {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>;
+		reg = <0x4208>;
+	};
+
+	timer4_fck: timer4_fck {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>;
+		reg = <0x420c>;
+	};
+
+	timer5_fck: timer5_fck {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>;
+		reg = <0x4210>;
+	};
+
+	timer6_fck: timer6_fck {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>;
+		reg = <0x4214>;
+	};
+
+	timer7_fck: timer7_fck {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>;
+		reg = <0x4218>;
+	};
+
+	wdt1_fck: wdt1_fck {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&clk_rc32k_ck>, <&clkdiv32k_ick>;
+		reg = <0x422c>;
+	};
+
+	l3_gclk: l3_gclk {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&dpll_core_m4_ck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	dpll_core_m4_div2_ck: dpll_core_m4_div2_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&sysclk_div>;
+		clock-mult = <1>;
+		clock-div = <2>;
+	};
+
+	l4hs_gclk: l4hs_gclk {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&dpll_core_m4_ck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	l3s_gclk: l3s_gclk {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&dpll_core_m4_div2_ck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	l4ls_gclk: l4ls_gclk {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&dpll_core_m4_div2_ck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	cpsw_125mhz_gclk: cpsw_125mhz_gclk {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&dpll_core_m5_ck>;
+		clock-mult = <1>;
+		clock-div = <2>;
+	};
+
+	cpsw_cpts_rft_clk: cpsw_cpts_rft_clk {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&sysclk_div>, <&dpll_core_m5_ck>, <&dpll_disp_m2_ck>;
+		reg = <0x4238>;
+	};
+
+	clk_32k_mosc_ck: clk_32k_mosc_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <32768>;
+	};
+
+	gpio0_dbclk_mux_ck: gpio0_dbclk_mux_ck {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&clk_rc32k_ck>, <&clk_32768_ck>, <&clkdiv32k_ick>, <&clk_32k_mosc_ck>, <&clk_32k_tpm_ck>;
+		reg = <0x4240>;
+	};
+
+	gpio0_dbclk: gpio0_dbclk {
+		#clock-cells = <0>;
+		compatible = "ti,gate-clock";
+		clocks = <&gpio0_dbclk_mux_ck>;
+		ti,bit-shift = <8>;
+		reg = <0x2b68>;
+	};
+
+	gpio1_dbclk: gpio1_dbclk {
+		#clock-cells = <0>;
+		compatible = "ti,gate-clock";
+		clocks = <&clkdiv32k_ick>;
+		ti,bit-shift = <8>;
+		reg = <0x8c78>;
+	};
+
+	gpio2_dbclk: gpio2_dbclk {
+		#clock-cells = <0>;
+		compatible = "ti,gate-clock";
+		clocks = <&clkdiv32k_ick>;
+		ti,bit-shift = <8>;
+		reg = <0x8c80>;
+	};
+
+	gpio3_dbclk: gpio3_dbclk {
+		#clock-cells = <0>;
+		compatible = "ti,gate-clock";
+		clocks = <&clkdiv32k_ick>;
+		ti,bit-shift = <8>;
+		reg = <0x8c88>;
+	};
+
+	gpio4_dbclk: gpio4_dbclk {
+		#clock-cells = <0>;
+		compatible = "ti,gate-clock";
+		clocks = <&clkdiv32k_ick>;
+		ti,bit-shift = <8>;
+		reg = <0x8c90>;
+	};
+
+	gpio5_dbclk: gpio5_dbclk {
+		#clock-cells = <0>;
+		compatible = "ti,gate-clock";
+		clocks = <&clkdiv32k_ick>;
+		ti,bit-shift = <8>;
+		reg = <0x8c98>;
+	};
+
+	mmc_clk: mmc_clk {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&dpll_per_m2_ck>;
+		clock-mult = <1>;
+		clock-div = <2>;
+	};
+
+	gfx_fclk_clksel_ck: gfx_fclk_clksel_ck {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&sysclk_div>, <&dpll_per_m2_ck>;
+		ti,bit-shift = <1>;
+		reg = <0x423c>;
+	};
+
+	gfx_fck_div_ck: gfx_fck_div_ck {
+		#clock-cells = <0>;
+		compatible = "ti,divider-clock";
+		clocks = <&gfx_fclk_clksel_ck>;
+		reg = <0x423c>;
+		ti,max-div = <2>;
+	};
+
+	disp_clk: disp_clk {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&dpll_disp_m2_ck>, <&dpll_core_m5_ck>, <&dpll_per_m2_ck>;
+		reg = <0x4244>;
+		ti,set-rate-parent;
+	};
+
+	dpll_extdev_ck: dpll_extdev_ck {
+		#clock-cells = <0>;
+		compatible = "ti,am3-dpll-clock";
+		clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
+		reg = <0x2e60>, <0x2e64>, <0x2e6c>;
+	};
+
+	dpll_extdev_m2_ck: dpll_extdev_m2_ck {
+		#clock-cells = <0>;
+		compatible = "ti,divider-clock";
+		clocks = <&dpll_extdev_ck>;
+		ti,max-div = <127>;
+		ti,autoidle-shift = <8>;
+		reg = <0x2e70>;
+		ti,index-starts-at-one;
+		ti,invert-autoidle-bit;
+	};
+
+	mux_synctimer32k_ck: mux_synctimer32k_ck {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&clk_32768_ck>, <&clk_32k_tpm_ck>, <&clkdiv32k_ick>;
+		reg = <0x4230>;
+	};
+
+	synctimer_32kclk: synctimer_32kclk {
+		#clock-cells = <0>;
+		compatible = "ti,gate-clock";
+		clocks = <&mux_synctimer32k_ck>;
+		ti,bit-shift = <8>;
+		reg = <0x2a30>;
+	};
+
+	timer8_fck: timer8_fck {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>, <&clk_32k_tpm_ck>;
+		reg = <0x421c>;
+	};
+
+	timer9_fck: timer9_fck {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>, <&clk_32k_tpm_ck>;
+		reg = <0x4220>;
+	};
+
+	timer10_fck: timer10_fck {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>, <&clk_32k_tpm_ck>;
+		reg = <0x4224>;
+	};
+
+	timer11_fck: timer11_fck {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>, <&clk_32k_tpm_ck>;
+		reg = <0x4228>;
+	};
+
+	cpsw_50m_clkdiv: cpsw_50m_clkdiv {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&dpll_core_m5_ck>;
+		clock-mult = <1>;
+		clock-div = <1>;
+	};
+
+	cpsw_5m_clkdiv: cpsw_5m_clkdiv {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&cpsw_50m_clkdiv>;
+		clock-mult = <1>;
+		clock-div = <10>;
+	};
+
+	dpll_ddr_x2_ck: dpll_ddr_x2_ck {
+		#clock-cells = <0>;
+		compatible = "ti,am3-dpll-x2-clock";
+		clocks = <&dpll_ddr_ck>;
+	};
+
+	dpll_ddr_m4_ck: dpll_ddr_m4_ck {
+		#clock-cells = <0>;
+		compatible = "ti,divider-clock";
+		clocks = <&dpll_ddr_x2_ck>;
+		ti,max-div = <31>;
+		ti,autoidle-shift = <8>;
+		reg = <0x2db8>;
+		ti,index-starts-at-one;
+		ti,invert-autoidle-bit;
+	};
+
+	dpll_per_clkdcoldo: dpll_per_clkdcoldo {
+		#clock-cells = <0>;
+		compatible = "ti,fixed-factor-clock";
+		clocks = <&dpll_per_ck>;
+		ti,clock-mult = <1>;
+		ti,clock-div = <1>;
+		ti,autoidle-shift = <8>;
+		reg = <0x2e14>;
+		ti,invert-autoidle-bit;
+	};
+
+	dll_aging_clk_div: dll_aging_clk_div {
+		#clock-cells = <0>;
+		compatible = "ti,divider-clock";
+		clocks = <&sys_clkin_ck>;
+		reg = <0x4250>;
+		ti,dividers = <8>, <16>, <32>;
+	};
+
+	div_core_25m_ck: div_core_25m_ck {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&sysclk_div>;
+		clock-mult = <1>;
+		clock-div = <8>;
+	};
+
+	func_12m_clk: func_12m_clk {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&dpll_per_m2_ck>;
+		clock-mult = <1>;
+		clock-div = <16>;
+	};
+
+	vtp_clk_div: vtp_clk_div {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&sys_clkin_ck>;
+		clock-mult = <1>;
+		clock-div = <2>;
+	};
+
+	usbphy_32khz_clkmux: usbphy_32khz_clkmux {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&clk_32768_ck>, <&clk_32k_tpm_ck>;
+		reg = <0x4260>;
+	};
+
+	usb_phy0_always_on_clk32k: usb_phy0_always_on_clk32k {
+		#clock-cells = <0>;
+		compatible = "ti,gate-clock";
+		clocks = <&usbphy_32khz_clkmux>;
+		ti,bit-shift = <8>;
+		reg = <0x2a40>;
+	};
+
+	usb_phy1_always_on_clk32k: usb_phy1_always_on_clk32k {
+		#clock-cells = <0>;
+		compatible = "ti,gate-clock";
+		clocks = <&usbphy_32khz_clkmux>;
+		ti,bit-shift = <8>;
+		reg = <0x2a48>;
+	};
+
+	usb_otg_ss0_refclk960m: usb_otg_ss0_refclk960m {
+		#clock-cells = <0>;
+		compatible = "ti,gate-clock";
+		clocks = <&dpll_per_clkdcoldo>;
+		ti,bit-shift = <8>;
+		reg = <0x8a60>;
+	};
+
+	usb_otg_ss1_refclk960m: usb_otg_ss1_refclk960m {
+		#clock-cells = <0>;
+		compatible = "ti,gate-clock";
+		clocks = <&dpll_per_clkdcoldo>;
+		ti,bit-shift = <8>;
+		reg = <0x8a68>;
+	};
+};

arch/arm/dts/am57xx-beagle-x15.dts

@@ -0,0 +1,699 @@
+/*
+ * Copyright (C) 2014 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "dra74x.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "TI AM5728 BeagleBoard-X15";
+	compatible = "ti,am572x-beagle-x15", "ti,am5728", "ti,dra742", "ti,dra74", "ti,dra7";
+
+	chosen {
+		stdout-path = &uart3;
+	};
+
+	aliases {
+		rtc0 = &mcp_rtc;
+		rtc1 = &tps659038_rtc;
+		rtc2 = &rtc;
+		display0 = &hdmi0;
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x80000000>;
+	};
+
+	vdd_3v3: fixedregulator-vdd_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_3v3";
+		vin-supply = <&regen1>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vtt_fixed: fixedregulator-vtt {
+		/* TPS51200 */
+		compatible = "regulator-fixed";
+		regulator-name = "vtt_fixed";
+		vin-supply = <&smps3_reg>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&gpio7 11 GPIO_ACTIVE_HIGH>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&leds_pins_default>;
+
+		led@0 {
+			label = "beagle-x15:usr0";
+			gpios = <&gpio7 9 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
+		};
+
+		led@1 {
+			label = "beagle-x15:usr1";
+			gpios = <&gpio7 8 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "cpu0";
+			default-state = "off";
+		};
+
+		led@2 {
+			label = "beagle-x15:usr2";
+			gpios = <&gpio7 14 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc0";
+			default-state = "off";
+		};
+
+		led@3 {
+			label = "beagle-x15:usr3";
+			gpios = <&gpio7 15 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "ide-disk";
+			default-state = "off";
+		};
+	};
+
+	gpio_fan: gpio_fan {
+		/* Based on 5v 500mA AFB02505HHB */
+		compatible = "gpio-fan";
+		gpios =  <&tps659038_gpio 2 GPIO_ACTIVE_HIGH>;
+		gpio-fan,speed-map = <0     0>,
+				     <13000 1>;
+		#cooling-cells = <2>;
+	};
+
+	extcon_usb1: extcon_usb1 {
+		compatible = "linux,extcon-usb-gpio";
+		id-gpio = <&gpio7 25 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&extcon_usb1_pins>;
+	};
+
+	extcon_usb2: extcon_usb2 {
+		compatible = "linux,extcon-usb-gpio";
+		id-gpio = <&gpio7 24 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&extcon_usb2_pins>;
+	};
+
+	hdmi0: connector {
+		compatible = "hdmi-connector";
+		label = "hdmi";
+
+		type = "a";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&tpd12s015_out>;
+			};
+		};
+	};
+
+	tpd12s015: encoder {
+		compatible = "ti,tpd12s015";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&tpd12s015_pins>;
+
+		gpios = <&gpio7 10 GPIO_ACTIVE_HIGH>,	/* gpio7_10, CT CP HPD */
+			<&gpio6 28 GPIO_ACTIVE_HIGH>,	/* gpio6_28, LS OE */
+			<&gpio7 12 GPIO_ACTIVE_HIGH>;	/* gpio7_12/sp1_cs2, HPD */
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				tpd12s015_in: endpoint {
+					remote-endpoint = <&hdmi_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				tpd12s015_out: endpoint {
+					remote-endpoint = <&hdmi_connector_in>;
+				};
+			};
+		};
+	};
+};
+
+&dra7_pmx_core {
+	leds_pins_default: leds_pins_default {
+		pinctrl-single,pins = <
+			0x3a8 (PIN_OUTPUT | MUX_MODE14)	/* spi1_d1.gpio7_8 */
+			0x3ac (PIN_OUTPUT | MUX_MODE14)	/* spi1_d0.gpio7_9 */
+			0x3c0 (PIN_OUTPUT | MUX_MODE14)	/* spi2_sclk.gpio7_14 */
+			0x3c4 (PIN_OUTPUT | MUX_MODE14)	/* spi2_d1.gpio7_15 */
+		>;
+	};
+
+	i2c1_pins_default: i2c1_pins_default {
+		pinctrl-single,pins = <
+			0x400 (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c1_sda.sda */
+			0x404 (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c1_scl.scl */
+		>;
+	};
+
+	hdmi_pins: pinmux_hdmi_pins {
+		pinctrl-single,pins = <
+			0x408 (PIN_INPUT | MUX_MODE1)	/* i2c2_sda.hdmi1_ddc_scl */
+			0x40c (PIN_INPUT | MUX_MODE1)	/* i2c2_scl.hdmi1_ddc_sda */
+		>;
+	};
+
+	i2c3_pins_default: i2c3_pins_default {
+		pinctrl-single,pins = <
+			0x2a4 (PIN_INPUT| MUX_MODE10)	/* mcasp1_aclkx.i2c3_sda */
+			0x2a8 (PIN_INPUT| MUX_MODE10)	/* mcasp1_fsx.i2c3_scl */
+		>;
+	};
+
+	uart3_pins_default: uart3_pins_default {
+		pinctrl-single,pins = <
+			0x3f8 (PIN_INPUT_SLEW | MUX_MODE2) /* uart2_ctsn.uart3_rxd */
+			0x3fc (PIN_INPUT_SLEW | MUX_MODE1) /* uart2_rtsn.uart3_txd */
+		>;
+	};
+
+	mmc1_pins_default: mmc1_pins_default {
+		pinctrl-single,pins = <
+			0x36c (PIN_INPUT | MUX_MODE14)	/* mmc1sdcd.gpio219 */
+			0x354 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */
+			0x358 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */
+			0x35c (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */
+			0x360 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */
+			0x364 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */
+			0x368 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */
+		>;
+	};
+
+	mmc2_pins_default: mmc2_pins_default {
+		pinctrl-single,pins = <
+			0x9c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */
+			0xb0 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
+			0xa0 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */
+			0xa4 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */
+			0xa8 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */
+			0xac (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */
+			0x8c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */
+			0x90 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */
+			0x94 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */
+			0x98 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
+		>;
+	};
+
+	cpsw_pins_default: cpsw_pins_default {
+		pinctrl-single,pins = <
+			/* Slave 1 */
+			0x250 (PIN_OUTPUT | MUX_MODE0)	/* rgmii1_tclk */
+			0x254 (PIN_OUTPUT | MUX_MODE0)	/* rgmii1_tctl */
+			0x258 (PIN_OUTPUT | MUX_MODE0)	/* rgmii1_td3 */
+			0x25c (PIN_OUTPUT | MUX_MODE0)	/* rgmii1_td2 */
+			0x260 (PIN_OUTPUT | MUX_MODE0)	/* rgmii1_td1 */
+			0x264 (PIN_OUTPUT | MUX_MODE0)	/* rgmii1_td0 */
+			0x268 (PIN_INPUT | MUX_MODE0)	/* rgmii1_rclk */
+			0x26c (PIN_INPUT | MUX_MODE0)	/* rgmii1_rctl */
+			0x270 (PIN_INPUT | MUX_MODE0)	/* rgmii1_rd3 */
+			0x274 (PIN_INPUT | MUX_MODE0)	/* rgmii1_rd2 */
+			0x278 (PIN_INPUT | MUX_MODE0)	/* rgmii1_rd1 */
+			0x27c (PIN_INPUT | MUX_MODE0)	/* rgmii1_rd0 */
+
+			/* Slave 2 */
+			0x198 (PIN_OUTPUT | MUX_MODE3)	/* rgmii2_tclk */
+			0x19c (PIN_OUTPUT | MUX_MODE3)	/* rgmii2_tctl */
+			0x1a0 (PIN_OUTPUT | MUX_MODE3)	/* rgmii2_td3 */
+			0x1a4 (PIN_OUTPUT | MUX_MODE3)	/* rgmii2_td2 */
+			0x1a8 (PIN_OUTPUT | MUX_MODE3)	/* rgmii2_td1 */
+			0x1ac (PIN_OUTPUT | MUX_MODE3)	/* rgmii2_td0 */
+			0x1b0 (PIN_INPUT | MUX_MODE3)	/* rgmii2_rclk */
+			0x1b4 (PIN_INPUT | MUX_MODE3)	/* rgmii2_rctl */
+			0x1b8 (PIN_INPUT | MUX_MODE3)	/* rgmii2_rd3 */
+			0x1bc (PIN_INPUT | MUX_MODE3)	/* rgmii2_rd2 */
+			0x1c0 (PIN_INPUT | MUX_MODE3)	/* rgmii2_rd1 */
+			0x1c4 (PIN_INPUT | MUX_MODE3)	/* rgmii2_rd0 */
+		>;
+
+	};
+
+	cpsw_pins_sleep: cpsw_pins_sleep {
+		pinctrl-single,pins = <
+			/* Slave 1 */
+			0x250 (PIN_INPUT | MUX_MODE15)
+			0x254 (PIN_INPUT | MUX_MODE15)
+			0x258 (PIN_INPUT | MUX_MODE15)
+			0x25c (PIN_INPUT | MUX_MODE15)
+			0x260 (PIN_INPUT | MUX_MODE15)
+			0x264 (PIN_INPUT | MUX_MODE15)
+			0x268 (PIN_INPUT | MUX_MODE15)
+			0x26c (PIN_INPUT | MUX_MODE15)
+			0x270 (PIN_INPUT | MUX_MODE15)
+			0x274 (PIN_INPUT | MUX_MODE15)
+			0x278 (PIN_INPUT | MUX_MODE15)
+			0x27c (PIN_INPUT | MUX_MODE15)
+
+			/* Slave 2 */
+			0x198 (PIN_INPUT | MUX_MODE15)
+			0x19c (PIN_INPUT | MUX_MODE15)
+			0x1a0 (PIN_INPUT | MUX_MODE15)
+			0x1a4 (PIN_INPUT | MUX_MODE15)
+			0x1a8 (PIN_INPUT | MUX_MODE15)
+			0x1ac (PIN_INPUT | MUX_MODE15)
+			0x1b0 (PIN_INPUT | MUX_MODE15)
+			0x1b4 (PIN_INPUT | MUX_MODE15)
+			0x1b8 (PIN_INPUT | MUX_MODE15)
+			0x1bc (PIN_INPUT | MUX_MODE15)
+			0x1c0 (PIN_INPUT | MUX_MODE15)
+			0x1c4 (PIN_INPUT | MUX_MODE15)
+		>;
+	};
+
+	davinci_mdio_pins_default: davinci_mdio_pins_default {
+		pinctrl-single,pins = <
+			/* MDIO */
+			0x23c (PIN_OUTPUT_PULLUP | MUX_MODE0)	/* mdio_mclk */
+			0x240 (PIN_INPUT_PULLUP | MUX_MODE0)	/* mdio_d */
+		>;
+	};
+
+	davinci_mdio_pins_sleep: davinci_mdio_pins_sleep {
+		pinctrl-single,pins = <
+			0x23c (PIN_INPUT | MUX_MODE15)
+			0x240 (PIN_INPUT | MUX_MODE15)
+		>;
+	};
+
+	tps659038_pins_default: tps659038_pins_default {
+		pinctrl-single,pins = <
+			0x418 (PIN_INPUT_PULLUP | MUX_MODE14)	/* wakeup0.gpio1_0 */
+		>;
+	};
+
+	tmp102_pins_default: tmp102_pins_default {
+		pinctrl-single,pins = <
+			0x3C8 (PIN_INPUT_PULLUP | MUX_MODE14)	/* spi2_d0.gpio7_16 */
+		>;
+	};
+
+	mcp79410_pins_default: mcp79410_pins_default {
+		pinctrl-single,pins = <
+			0x424 (PIN_INPUT_PULLUP | MUX_MODE1)	/* wakeup3.sys_nirq1 */
+		>;
+	};
+
+	usb1_pins: pinmux_usb1_pins {
+		pinctrl-single,pins = <
+			0x280 (PIN_INPUT_SLEW | MUX_MODE0) /* usb1_drvvbus */
+		>;
+	};
+
+	extcon_usb1_pins: extcon_usb1_pins {
+		pinctrl-single,pins = <
+			0x3ec (PIN_INPUT_PULLUP | MUX_MODE14) /* uart1_rtsn.gpio7_25 */
+		>;
+	};
+
+	extcon_usb2_pins: extcon_usb2_pins {
+		pinctrl-single,pins = <
+			0x3e8 (PIN_INPUT_PULLUP | MUX_MODE14) /* uart1_ctsn.gpio7_24 */
+		>;
+	};
+
+	tpd12s015_pins: pinmux_tpd12s015_pins {
+		pinctrl-single,pins = <
+			0x3b0 (PIN_OUTPUT | MUX_MODE14)		/* gpio7_10 CT_CP_HPD */
+			0x3b8 (PIN_INPUT_PULLDOWN | MUX_MODE14)	/* gpio7_12 HPD */
+			0x370 (PIN_OUTPUT | MUX_MODE14)		/* gpio6_28 LS_OE */
+		>;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins_default>;
+	clock-frequency = <400000>;
+
+	tps659038: tps659038@58 {
+		compatible = "ti,tps659038";
+		reg = <0x58>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&tps659038_pins_default>;
+
+		#interrupt-cells = <2>;
+		interrupt-controller;
+
+		ti,system-power-controller;
+
+		tps659038_pmic {
+			compatible = "ti,tps659038-pmic";
+
+			regulators {
+				smps12_reg: smps12 {
+					/* VDD_MPU */
+					regulator-name = "smps12";
+					regulator-min-microvolt = < 850000>;
+					regulator-max-microvolt = <1250000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				smps3_reg: smps3 {
+					/* VDD_DDR */
+					regulator-name = "smps3";
+					regulator-min-microvolt = <1350000>;
+					regulator-max-microvolt = <1350000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				smps45_reg: smps45 {
+					/* VDD_DSPEVE, VDD_IVA, VDD_GPU */
+					regulator-name = "smps45";
+					regulator-min-microvolt = < 850000>;
+					regulator-max-microvolt = <1150000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				smps6_reg: smps6 {
+					/* VDD_CORE */
+					regulator-name = "smps6";
+					regulator-min-microvolt = <850000>;
+					regulator-max-microvolt = <1030000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				/* SMPS7 unused */
+
+				smps8_reg: smps8 {
+					/* VDD_1V8 */
+					regulator-name = "smps8";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				/* SMPS9 unused */
+
+				ldo1_reg: ldo1 {
+					/* VDD_SD  */
+					regulator-name = "ldo1";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-boot-on;
+				};
+
+				ldo2_reg: ldo2 {
+					/* VDD_SHV5 */
+					regulator-name = "ldo2";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				ldo3_reg: ldo3 {
+					/* VDDA_1V8_PHY */
+					regulator-name = "ldo3";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				ldo9_reg: ldo9 {
+					/* VDD_RTC */
+					regulator-name = "ldo9";
+					regulator-min-microvolt = <1050000>;
+					regulator-max-microvolt = <1050000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				ldoln_reg: ldoln {
+					/* VDDA_1V8_PLL */
+					regulator-name = "ldoln";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				ldousb_reg: ldousb {
+					/* VDDA_3V_USB: VDDA_USBHS33 */
+					regulator-name = "ldousb";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-boot-on;
+				};
+
+				regen1: regen1 {
+					/* VDD_3V3_ON */
+					regulator-name = "regen1";
+					regulator-boot-on;
+					regulator-always-on;
+				};
+			};
+		};
+
+		tps659038_rtc: tps659038_rtc {
+			compatible = "ti,palmas-rtc";
+			interrupt-parent = <&tps659038>;
+			interrupts = <8 IRQ_TYPE_EDGE_FALLING>;
+			wakeup-source;
+		};
+
+		tps659038_pwr_button: tps659038_pwr_button {
+			compatible = "ti,palmas-pwrbutton";
+			interrupt-parent = <&tps659038>;
+			interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
+			wakeup-source;
+			ti,palmas-long-press-seconds = <12>;
+		};
+
+		tps659038_gpio: tps659038_gpio {
+			compatible = "ti,palmas-gpio";
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+	};
+
+	tmp102: tmp102@48 {
+		compatible = "ti,tmp102";
+		reg = <0x48>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&tmp102_pins_default>;
+		interrupt-parent = <&gpio7>;
+		interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
+		#thermal-sensor-cells = <1>;
+	};
+};
+
+&i2c3 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c3_pins_default>;
+	clock-frequency = <400000>;
+
+	mcp_rtc: rtc@6f {
+		compatible = "microchip,mcp7941x";
+		reg = <0x6f>;
+		interrupts = <GIC_SPI 2 IRQ_TYPE_EDGE_RISING>;  /* IRQ_SYS_1N */
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&mcp79410_pins_default>;
+
+		vcc-supply = <&vdd_3v3>;
+		wakeup-source;
+	};
+};
+
+&gpio7 {
+	ti,no-reset-on-init;
+	ti,no-idle-on-init;
+};
+
+&cpu0 {
+	cpu0-supply = <&smps12_reg>;
+	voltage-tolerance = <1>;
+};
+
+&uart3 {
+	status = "okay";
+	interrupts-extended = <&crossbar_mpu GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
+			      <&dra7_pmx_core 0x3f8>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins_default>;
+};
+
+&mac {
+	status = "okay";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&cpsw_pins_default>;
+	pinctrl-1 = <&cpsw_pins_sleep>;
+	dual_emac;
+};
+
+&cpsw_emac0 {
+	phy_id = <&davinci_mdio>, <1>;
+	phy-mode = "rgmii";
+	dual_emac_res_vlan = <1>;
+};
+
+&cpsw_emac1 {
+	phy_id = <&davinci_mdio>, <2>;
+	phy-mode = "rgmii";
+	dual_emac_res_vlan = <2>;
+};
+
+&davinci_mdio {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&davinci_mdio_pins_default>;
+	pinctrl-1 = <&davinci_mdio_pins_sleep>;
+};
+
+&mmc1 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins_default>;
+
+	vmmc-supply = <&ldo1_reg>;
+	vmmc_aux-supply = <&vdd_3v3>;
+	pbias-supply = <&pbias_mmc_reg>;
+	bus-width = <4>;
+	cd-gpios = <&gpio6 27 0>; /* gpio 219 */
+};
+
+&mmc2 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_pins_default>;
+
+	vmmc-supply = <&vdd_3v3>;
+	bus-width = <8>;
+	ti,non-removable;
+	cap-mmc-dual-data-rate;
+};
+
+&sata {
+	status = "okay";
+};
+
+&usb2_phy1 {
+	phy-supply = <&ldousb_reg>;
+};
+
+&usb2_phy2 {
+	phy-supply = <&ldousb_reg>;
+};
+
+&usb1 {
+	dr_mode = "host";
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb1_pins>;
+};
+
+&omap_dwc3_1 {
+	extcon = <&extcon_usb1>;
+};
+
+&omap_dwc3_2 {
+	extcon = <&extcon_usb2>;
+};
+
+&usb2 {
+	dr_mode = "peripheral";
+};
+
+&cpu_trips {
+	cpu_alert1: cpu_alert1 {
+		temperature = <50000>; /* millicelsius */
+		hysteresis = <2000>; /* millicelsius */
+		type = "active";
+	};
+};
+
+&cpu_cooling_maps {
+	map1 {
+		trip = <&cpu_alert1>;
+		cooling-device = <&gpio_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+	};
+};
+
+&thermal_zones {
+	board_thermal: board_thermal {
+		polling-delay-passive = <1250>; /* milliseconds */
+		polling-delay = <1500>; /* milliseconds */
+
+				/* sensor       ID */
+		thermal-sensors = <&tmp102     0>;
+
+		board_trips: trips {
+			board_alert0: board_alert {
+				temperature = <40000>; /* millicelsius */
+				hysteresis = <2000>; /* millicelsius */
+				type = "active";
+			};
+
+			board_crit: board_crit {
+				temperature = <105000>; /* millicelsius */
+				hysteresis = <0>; /* millicelsius */
+				type = "critical";
+			};
+		};
+
+		board_cooling_maps: cooling-maps {
+			map0 {
+				trip = <&board_alert0>;
+				cooling-device =
+				  <&gpio_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+			};
+		};
+       };
+};
+
+&dss {
+	status = "ok";
+
+	vdda_video-supply = <&ldoln_reg>;
+};
+
+&hdmi {
+	status = "ok";
+	vdda-supply = <&ldo3_reg>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&hdmi_pins>;
+
+	port {
+		hdmi_out: endpoint {
+			remote-endpoint = <&tpd12s015_in>;
+		};
+	};
+};

arch/arm/dts/armada-370-xp.dtsi

@@ -0,0 +1,333 @@
+/*
+ * Device Tree Include file for Marvell Armada 370 and Armada XP SoC
+ *
+ * Copyright (C) 2012 Marvell
+ *
+ * Lior Amsalem <alior@marvell.com>
+ * Gregory CLEMENT <gregory.clement@free-electrons.com>
+ * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ * Ben Dooks <ben.dooks@codethink.co.uk>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * This file contains the definitions that are common to the Armada
+ * 370 and Armada XP SoC.
+ */
+
+/include/ "skeleton64.dtsi"
+
+#define MBUS_ID(target,attributes) (((target) << 24) | ((attributes) << 16))
+
+/ {
+	model = "Marvell Armada 370 and XP SoC";
+	compatible = "marvell,armada-370-xp";
+
+	aliases {
+		serial0 = &uart0;
+		serial1 = &uart1;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		cpu@0 {
+			compatible = "marvell,sheeva-v7";
+			device_type = "cpu";
+			reg = <0>;
+		};
+	};
+
+	pmu {
+		compatible = "arm,cortex-a9-pmu";
+		interrupts-extended = <&mpic 3>;
+	};
+
+	soc {
+		#address-cells = <2>;
+		#size-cells = <1>;
+		controller = <&mbusc>;
+		interrupt-parent = <&mpic>;
+		pcie-mem-aperture = <0xf8000000 0x7e00000>;
+		pcie-io-aperture  = <0xffe00000 0x100000>;
+
+		devbus-bootcs {
+			compatible = "marvell,mvebu-devbus";
+			reg = <MBUS_ID(0xf0, 0x01) 0x10400 0x8>;
+			ranges = <0 MBUS_ID(0x01, 0x2f) 0 0xffffffff>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&coreclk 0>;
+			status = "disabled";
+		};
+
+		devbus-cs0 {
+			compatible = "marvell,mvebu-devbus";
+			reg = <MBUS_ID(0xf0, 0x01) 0x10408 0x8>;
+			ranges = <0 MBUS_ID(0x01, 0x3e) 0 0xffffffff>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&coreclk 0>;
+			status = "disabled";
+		};
+
+		devbus-cs1 {
+			compatible = "marvell,mvebu-devbus";
+			reg = <MBUS_ID(0xf0, 0x01) 0x10410 0x8>;
+			ranges = <0 MBUS_ID(0x01, 0x3d) 0 0xffffffff>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&coreclk 0>;
+			status = "disabled";
+		};
+
+		devbus-cs2 {
+			compatible = "marvell,mvebu-devbus";
+			reg = <MBUS_ID(0xf0, 0x01) 0x10418 0x8>;
+			ranges = <0 MBUS_ID(0x01, 0x3b) 0 0xffffffff>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&coreclk 0>;
+			status = "disabled";
+		};
+
+		devbus-cs3 {
+			compatible = "marvell,mvebu-devbus";
+			reg = <MBUS_ID(0xf0, 0x01) 0x10420 0x8>;
+			ranges = <0 MBUS_ID(0x01, 0x37) 0 0xffffffff>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&coreclk 0>;
+			status = "disabled";
+		};
+
+		internal-regs {
+			compatible = "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 MBUS_ID(0xf0, 0x01) 0 0x100000>;
+
+			rtc@10300 {
+				compatible = "marvell,orion-rtc";
+				reg = <0x10300 0x20>;
+				interrupts = <50>;
+			};
+
+			spi0: spi@10600 {
+				reg = <0x10600 0x28>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				cell-index = <0>;
+				interrupts = <30>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
+
+			spi1: spi@10680 {
+				reg = <0x10680 0x28>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				cell-index = <1>;
+				interrupts = <92>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
+
+			i2c0: i2c@11000 {
+				compatible = "marvell,mv64xxx-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interrupts = <31>;
+				timeout-ms = <1000>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
+
+			i2c1: i2c@11100 {
+				compatible = "marvell,mv64xxx-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interrupts = <32>;
+				timeout-ms = <1000>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
+
+			uart0: serial@12000 {
+				compatible = "snps,dw-apb-uart";
+				reg = <0x12000 0x100>;
+				reg-shift = <2>;
+				interrupts = <41>;
+				reg-io-width = <1>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
+
+			uart1: serial@12100 {
+				compatible = "snps,dw-apb-uart";
+				reg = <0x12100 0x100>;
+				reg-shift = <2>;
+				interrupts = <42>;
+				reg-io-width = <1>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
+
+			pinctrl: pin-ctrl@18000 {
+				reg = <0x18000 0x38>;
+			};
+
+			coredivclk: corediv-clock@18740 {
+				compatible = "marvell,armada-370-corediv-clock";
+				reg = <0x18740 0xc>;
+				#clock-cells = <1>;
+				clocks = <&mainpll>;
+				clock-output-names = "nand";
+			};
+
+			mbusc: mbus-controller@20000 {
+				compatible = "marvell,mbus-controller";
+				reg = <0x20000 0x100>, <0x20180 0x20>,
+				      <0x20250 0x8>;
+			};
+
+			mpic: interrupt-controller@20a00 {
+				compatible = "marvell,mpic";
+				#interrupt-cells = <1>;
+				#size-cells = <1>;
+				interrupt-controller;
+				msi-controller;
+			};
+
+			coherency-fabric@20200 {
+				compatible = "marvell,coherency-fabric";
+				reg = <0x20200 0xb0>, <0x21010 0x1c>;
+			};
+
+			timer@20300 {
+				reg = <0x20300 0x30>, <0x21040 0x30>;
+				interrupts = <37>, <38>, <39>, <40>, <5>, <6>;
+			};
+
+			watchdog@20300 {
+				reg = <0x20300 0x34>, <0x20704 0x4>;
+			};
+
+			pmsu@22000 {
+				compatible = "marvell,armada-370-pmsu";
+				reg = <0x22000 0x1000>;
+			};
+
+			usb@50000 {
+				compatible = "marvell,orion-ehci";
+				reg = <0x50000 0x500>;
+				interrupts = <45>;
+				status = "disabled";
+			};
+
+			usb@51000 {
+				compatible = "marvell,orion-ehci";
+				reg = <0x51000 0x500>;
+				interrupts = <46>;
+				status = "disabled";
+			};
+
+			eth0: ethernet@70000 {
+				reg = <0x70000 0x4000>;
+				interrupts = <8>;
+				clocks = <&gateclk 4>;
+				status = "disabled";
+			};
+
+			mdio: mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "marvell,orion-mdio";
+				reg = <0x72004 0x4>;
+				clocks = <&gateclk 4>;
+			};
+
+			eth1: ethernet@74000 {
+				reg = <0x74000 0x4000>;
+				interrupts = <10>;
+				clocks = <&gateclk 3>;
+				status = "disabled";
+			};
+
+			sata@a0000 {
+				compatible = "marvell,armada-370-sata";
+				reg = <0xa0000 0x5000>;
+				interrupts = <55>;
+				clocks = <&gateclk 15>, <&gateclk 30>;
+				clock-names = "0", "1";
+				status = "disabled";
+			};
+
+			nand@d0000 {
+				compatible = "marvell,armada370-nand";
+				reg = <0xd0000 0x54>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				interrupts = <113>;
+				clocks = <&coredivclk 0>;
+				status = "disabled";
+			};
+
+			mvsdio@d4000 {
+				compatible = "marvell,orion-sdio";
+				reg = <0xd4000 0x200>;
+				interrupts = <54>;
+				clocks = <&gateclk 17>;
+				bus-width = <4>;
+				cap-sdio-irq;
+				cap-sd-highspeed;
+				cap-mmc-highspeed;
+				status = "disabled";
+			};
+		};
+	};
+
+	clocks {
+		/* 2 GHz fixed main PLL */
+		mainpll: mainpll {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <2000000000>;
+		};
+	};
+ };

arch/arm/dts/armada-380.dtsi

@@ -0,0 +1,152 @@
+/*
+ * Device Tree Include file for Marvell Armada 380 SoC.
+ *
+ * Copyright (C) 2014 Marvell
+ *
+ * Lior Amsalem <alior@marvell.com>
+ * Gregory CLEMENT <gregory.clement@free-electrons.com>
+ * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "armada-38x.dtsi"
+
+/ {
+	model = "Marvell Armada 380 family SoC";
+	compatible = "marvell,armada380";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		enable-method = "marvell,armada-380-smp";
+
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			reg = <0>;
+		};
+	};
+
+	soc {
+		internal-regs {
+			pinctrl@18000 {
+				compatible = "marvell,mv88f6810-pinctrl";
+			};
+		};
+
+		pcie-controller {
+			compatible = "marvell,armada-370-pcie";
+			status = "disabled";
+			device_type = "pci";
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			msi-parent = <&mpic>;
+			bus-range = <0x00 0xff>;
+
+			ranges =
+			       <0x82000000 0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x00002000
+				0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000
+				0x82000000 0 0x44000 MBUS_ID(0xf0, 0x01) 0x44000 0 0x00002000
+				0x82000000 0 0x48000 MBUS_ID(0xf0, 0x01) 0x48000 0 0x00002000
+				0x82000000 0x1 0     MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 0 MEM */
+				0x81000000 0x1 0     MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 0 IO  */
+				0x82000000 0x2 0     MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 1 MEM */
+				0x81000000 0x2 0     MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 1 IO  */
+				0x82000000 0x3 0     MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 2 MEM */
+				0x81000000 0x3 0     MBUS_ID(0x04, 0xd0) 0 1 0 /* Port 2 IO  */>;
+
+			/* x1 port */
+			pcie@1,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x80000 0 0x2000>;
+				reg = <0x0800 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
+					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+				marvell,pcie-port = <0>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 8>;
+				status = "disabled";
+			};
+
+			/* x1 port */
+			pcie@2,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+				reg = <0x1000 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
+					  0x81000000 0 0 0x81000000 0x2 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+				marvell,pcie-port = <1>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 5>;
+				status = "disabled";
+			};
+
+			/* x1 port */
+			pcie@3,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
+				reg = <0x1800 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0
+					  0x81000000 0 0 0x81000000 0x3 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
+				marvell,pcie-port = <2>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 6>;
+				status = "disabled";
+			};
+		};
+	};
+};

arch/arm/dts/armada-385.dtsi

@@ -0,0 +1,184 @@
+/*
+ * Device Tree Include file for Marvell Armada 385 SoC.
+ *
+ * Copyright (C) 2014 Marvell
+ *
+ * Lior Amsalem <alior@marvell.com>
+ * Gregory CLEMENT <gregory.clement@free-electrons.com>
+ * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "armada-38x.dtsi"
+
+/ {
+	model = "Marvell Armada 385 family SoC";
+	compatible = "marvell,armada385", "marvell,armada380";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		enable-method = "marvell,armada-380-smp";
+
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			reg = <0>;
+		};
+		cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			reg = <1>;
+		};
+	};
+
+	soc {
+		internal-regs {
+			pinctrl@18000 {
+				compatible = "marvell,mv88f6820-pinctrl";
+			};
+		};
+
+		pcie-controller {
+			compatible = "marvell,armada-370-pcie";
+			status = "disabled";
+			device_type = "pci";
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			msi-parent = <&mpic>;
+			bus-range = <0x00 0xff>;
+
+			ranges =
+			       <0x82000000 0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x00002000
+				0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000
+				0x82000000 0 0x44000 MBUS_ID(0xf0, 0x01) 0x44000 0 0x00002000
+				0x82000000 0 0x48000 MBUS_ID(0xf0, 0x01) 0x48000 0 0x00002000
+				0x82000000 0x1 0     MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 0 MEM */
+				0x81000000 0x1 0     MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 0 IO  */
+				0x82000000 0x2 0     MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 1 MEM */
+				0x81000000 0x2 0     MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 1 IO  */
+				0x82000000 0x3 0     MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 2 MEM */
+				0x81000000 0x3 0     MBUS_ID(0x04, 0xd0) 0 1 0 /* Port 2 IO  */
+				0x82000000 0x4 0     MBUS_ID(0x04, 0xb8) 0 1 0 /* Port 3 MEM */
+				0x81000000 0x4 0     MBUS_ID(0x04, 0xb0) 0 1 0 /* Port 3 IO  */>;
+
+			/*
+			 * This port can be either x4 or x1. When
+			 * configured in x4 by the bootloader, then
+			 * pcie@4,0 is not available.
+			 */
+			pcie@1,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x80000 0 0x2000>;
+				reg = <0x0800 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
+					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+				marvell,pcie-port = <0>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 8>;
+				status = "disabled";
+			};
+
+			/* x1 port */
+			pcie@2,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+				reg = <0x1000 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
+					  0x81000000 0 0 0x81000000 0x2 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+				marvell,pcie-port = <1>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 5>;
+				status = "disabled";
+			};
+
+			/* x1 port */
+			pcie@3,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
+				reg = <0x1800 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0
+					  0x81000000 0 0 0x81000000 0x3 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
+				marvell,pcie-port = <2>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 6>;
+				status = "disabled";
+			};
+
+			/*
+			 * x1 port only available when pcie@1,0 is
+			 * configured as a x1 port
+			 */
+			pcie@4,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x48000 0 0x2000>;
+				reg = <0x2000 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0
+					  0x81000000 0 0 0x81000000 0x4 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &gic GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+				marvell,pcie-port = <3>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 7>;
+				status = "disabled";
+			};
+		};
+	};
+};

arch/arm/dts/armada-388-gp.dts

@@ -0,0 +1,413 @@
+/*
+ * Device Tree file for Marvell Armada 385 development board
+ * (RD-88F6820-GP)
+ *
+ * Copyright (C) 2014 Marvell
+ *
+ * Gregory CLEMENT <gregory.clement@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is licensed under the terms of the GNU General Public
+ *     License version 2.  This program is licensed "as is" without
+ *     any warranty of any kind, whether express or implied.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "armada-388.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Marvell Armada 385 GP";
+	compatible = "marvell,a385-gp", "marvell,armada388", "marvell,armada380";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x80000000>; /* 2 GB */
+	};
+
+	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
+			  MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000>;
+
+		internal-regs {
+			spi@10600 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&spi0_pins>;
+				status = "okay";
+
+				spi-flash@0 {
+					#address-cells = <1>;
+					#size-cells = <1>;
+					compatible = "st,m25p128", "jedec,spi-nor";
+					reg = <0>; /* Chip select 0 */
+					spi-max-frequency = <50000000>;
+					m25p,fast-read;
+				};
+			};
+
+			i2c@11000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&i2c0_pins>;
+				status = "okay";
+				clock-frequency = <100000>;
+				/*
+				 * The EEPROM located at adresse 54 is needed
+				 * for the boot - DO NOT ERASE IT -
+				 */
+
+				expander0: pca9555@20 {
+					compatible = "nxp,pca9555";
+					pinctrl-names = "default";
+					pinctrl-0 = <&pca0_pins>;
+					interrupt-parent = <&gpio0>;
+					interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
+					gpio-controller;
+					#gpio-cells = <2>;
+					interrupt-controller;
+					#interrupt-cells = <2>;
+					reg = <0x20>;
+				};
+
+				expander1: pca9555@21 {
+					compatible = "nxp,pca9555";
+					pinctrl-names = "default";
+					interrupt-parent = <&gpio0>;
+					interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
+					gpio-controller;
+					#gpio-cells = <2>;
+					interrupt-controller;
+					#interrupt-cells = <2>;
+					reg = <0x21>;
+				};
+
+			};
+
+			serial@12000 {
+				/*
+				 * Exported on the micro USB connector CON16
+				 * through an FTDI
+				 */
+
+				pinctrl-names = "default";
+				pinctrl-0 = <&uart0_pins>;
+				status = "okay";
+			};
+
+			/* GE1 CON15 */
+			ethernet@30000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&ge1_rgmii_pins>;
+				status = "okay";
+				phy = <&phy1>;
+				phy-mode = "rgmii-id";
+			};
+
+			/* CON4 */
+			usb@58000 {
+				vcc-supply = <&reg_usb2_0_vbus>;
+				status = "okay";
+			};
+
+			/* GE0 CON1 */
+			ethernet@70000 {
+				pinctrl-names = "default";
+				/*
+				 * The Reference Clock 0 is used to provide a
+				 * clock to the PHY
+				 */
+				pinctrl-0 = <&ge0_rgmii_pins>, <&ref_clk0_pins>;
+				status = "okay";
+				phy = <&phy0>;
+				phy-mode = "rgmii-id";
+			};
+
+
+			mdio@72004 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&mdio_pins>;
+
+				phy0: ethernet-phy@1 {
+					reg = <1>;
+				};
+
+				phy1: ethernet-phy@0 {
+					reg = <0>;
+				};
+			};
+
+			sata@a8000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&sata0_pins>, <&sata1_pins>;
+				status = "okay";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				sata0: sata-port@0 {
+					reg = <0>;
+					target-supply = <&reg_5v_sata0>;
+				};
+
+				sata1: sata-port@1 {
+					reg = <1>;
+					target-supply = <&reg_5v_sata1>;
+				};
+			};
+
+			sata@e0000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&sata2_pins>, <&sata3_pins>;
+				status = "okay";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				sata2: sata-port@0 {
+					reg = <0>;
+					target-supply = <&reg_5v_sata2>;
+				};
+
+				sata3: sata-port@1 {
+					reg = <1>;
+					target-supply = <&reg_5v_sata3>;
+				};
+			};
+
+			sdhci@d8000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&sdhci_pins>;
+				cd-gpios = <&expander0 5 GPIO_ACTIVE_LOW>;
+				no-1-8-v;
+				wp-inverted;
+				bus-width = <8>;
+				status = "okay";
+			};
+
+			/* CON5 */
+			usb3@f0000 {
+				vcc-supply = <&reg_usb2_1_vbus>;
+				status = "okay";
+			};
+
+			/* CON7 */
+			usb3@f8000 {
+				vcc-supply = <&reg_usb3_vbus>;
+				status = "okay";
+			};
+		};
+
+		pcie-controller {
+			status = "okay";
+			/*
+			 * One PCIe units is accessible through
+			 * standard PCIe slot on the board.
+			 */
+			pcie@1,0 {
+				/* Port 0, Lane 0 */
+				status = "okay";
+			};
+
+			/*
+			 * The two other PCIe units are accessible
+			 * through mini PCIe slot on the board.
+			 */
+			pcie@2,0 {
+				/* Port 1, Lane 0 */
+				status = "okay";
+			};
+			pcie@3,0 {
+				/* Port 2, Lane 0 */
+				status = "okay";
+			};
+		};
+
+		gpio-fan {
+			compatible = "gpio-fan";
+			gpios = <&expander1 3 GPIO_ACTIVE_HIGH>;
+			gpio-fan,speed-map = <	 0 0
+					      3000 1>;
+		};
+	};
+
+	reg_usb3_vbus: usb3-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb3-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		regulator-always-on;
+		gpio = <&expander1 15 GPIO_ACTIVE_HIGH>;
+	};
+
+	reg_usb2_0_vbus: v5-vbus0 {
+		compatible = "regulator-fixed";
+		regulator-name = "v5.0-vbus0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		regulator-always-on;
+		gpio = <&expander1 14 GPIO_ACTIVE_HIGH>;
+	};
+
+	reg_usb2_1_vbus: v5-vbus1 {
+		compatible = "regulator-fixed";
+		regulator-name = "v5.0-vbus1";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		regulator-always-on;
+		gpio = <&expander0 4 GPIO_ACTIVE_HIGH>;
+	};
+
+	reg_usb2_1_vbus: v5-vbus1 {
+		compatible = "regulator-fixed";
+		regulator-name = "v5.0-vbus1";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		regulator-always-on;
+		gpio = <&expander0 4 GPIO_ACTIVE_HIGH>;
+	};
+
+	reg_sata0: pwr-sata0 {
+		compatible = "regulator-fixed";
+		regulator-name = "pwr_en_sata0";
+		enable-active-high;
+		regulator-always-on;
+
+	};
+
+	reg_5v_sata0: v5-sata0 {
+		compatible = "regulator-fixed";
+		regulator-name = "v5.0-sata0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		vin-supply = <&reg_sata0>;
+	};
+
+	reg_12v_sata0: v12-sata0 {
+		compatible = "regulator-fixed";
+		regulator-name = "v12.0-sata0";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+		vin-supply = <&reg_sata0>;
+	};
+
+	reg_sata1: pwr-sata1 {
+		regulator-name = "pwr_en_sata1";
+		compatible = "regulator-fixed";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		enable-active-high;
+		regulator-always-on;
+		gpio = <&expander0 3 GPIO_ACTIVE_HIGH>;
+	};
+
+	reg_5v_sata1: v5-sata1 {
+		compatible = "regulator-fixed";
+		regulator-name = "v5.0-sata1";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		vin-supply = <&reg_sata1>;
+	};
+
+	reg_12v_sata1: v12-sata1 {
+		compatible = "regulator-fixed";
+		regulator-name = "v12.0-sata1";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+		vin-supply = <&reg_sata1>;
+	};
+
+	reg_sata2: pwr-sata2 {
+		compatible = "regulator-fixed";
+		regulator-name = "pwr_en_sata2";
+		enable-active-high;
+		regulator-always-on;
+		gpio = <&expander0 11 GPIO_ACTIVE_HIGH>;
+	};
+
+	reg_5v_sata2: v5-sata2 {
+		compatible = "regulator-fixed";
+		regulator-name = "v5.0-sata2";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		vin-supply = <&reg_sata2>;
+	};
+
+	reg_12v_sata2: v12-sata2 {
+		compatible = "regulator-fixed";
+		regulator-name = "v12.0-sata2";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+		vin-supply = <&reg_sata2>;
+	};
+
+	reg_sata3: pwr-sata3 {
+		compatible = "regulator-fixed";
+		regulator-name = "pwr_en_sata3";
+		enable-active-high;
+		regulator-always-on;
+		gpio = <&expander0 12 GPIO_ACTIVE_HIGH>;
+	};
+
+	reg_5v_sata3: v5-sata3 {
+		compatible = "regulator-fixed";
+		regulator-name = "v5.0-sata3";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		vin-supply = <&reg_sata3>;
+	};
+
+	reg_12v_sata3: v12-sata3 {
+		compatible = "regulator-fixed";
+		regulator-name = "v12.0-sata3";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+		vin-supply = <&reg_sata3>;
+	};
+};
+
+&pinctrl {
+	pca0_pins: pca0_pins {
+		marvell,pins = "mpp18";
+		marvell,function = "gpio";
+	};
+};

arch/arm/dts/armada-388.dtsi

@@ -1,21 +1,18 @@
 /*
- * Copyright 2015 Vishnu Patekar
- * Vishnu Patekar <vishnupatekar0510@gmail.com>
+ * Device Tree Include file for Marvell Armada 388 SoC.
+ *
+ * Copyright (C) 2015 Marvell
+ *
+ * Gregory CLEMENT <gregory.clement@free-electrons.com>
  *
  * This file is dual-licensed: you can use it either under the terms
  * of the GPL or the X11 license, at your option. Note that this dual
  * licensing only applies to this file, and not this project as a
  * whole.
  *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of the
- *     License, or (at your option) any later version.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
+ *  a) This file is licensed under the terms of the GNU General Public
+ *     License version 2.  This program is licensed "as is" without
+ *     any warranty of any kind, whether express or implied.
  *
  * Or, alternatively,
  *
@@ -39,50 +36,35 @@
  *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
  *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
  *     OTHER DEALINGS IN THE SOFTWARE.
+ *
+ *
+ * The main difference with the Armada 385 is that the 388 can handle two more
+ * SATA ports. So we can reuse the dtsi of the Armada 385, override the pinctrl
+ * property and the name of the SoC, and add the second SATA host which control
+ * the 2 other ports.
  */
 
-/dts-v1/;
-#include "sun8i-a33.dtsi"
-#include "sunxi-common-regulators.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include "armada-385.dtsi"
 
 / {
-	model = "ET Q8 Quad Core Tablet (v1.6)";
-	compatible = "et,q8-v1.6", "allwinner,sun8i-a33";
+	model = "Marvell Armada 388 family SoC";
+	compatible = "marvell,armada388", "marvell,armada385",
+		"marvell,armada380";
 
-	aliases {
-		serial0 = &uart0;
-	};
+	soc {
+		internal-regs {
+			pinctrl@18000 {
+				compatible = "marvell,mv88f6828-pinctrl";
+			};
 
-	chosen {
-		stdout-path = "serial0:115200n8";
+			sata@e0000 {
+				compatible = "marvell,armada-380-ahci";
+				reg = <0xe0000 0x2000>;
+				interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gateclk 30>;
+				status = "disabled";
+			};
+
+		};
 	};
 };
-
-&lradc {
-	vref-supply = <&reg_vcc3v0>;
-	status = "okay";
-
-	button@200 {
-		label = "Volume Up";
-		linux,code = <KEY_VOLUMEUP>;
-		channel = <0>;
-		voltage = <200000>;
-	};
-
-	button@400 {
-		label = "Volume Down";
-		linux,code = <KEY_VOLUMEDOWN>;
-		channel = <0>;
-		voltage = <400000>;
-	};
-};
-
-&uart0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
-	status = "okay";
-};

arch/arm/dts/armada-38x.dtsi

@@ -0,0 +1,600 @@
+/*
+ * Device Tree Include file for Marvell Armada 38x family of SoCs.
+ *
+ * Copyright (C) 2014 Marvell
+ *
+ * Lior Amsalem <alior@marvell.com>
+ * Gregory CLEMENT <gregory.clement@free-electrons.com>
+ * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "skeleton.dtsi"
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+#define MBUS_ID(target,attributes) (((target) << 24) | ((attributes) << 16))
+
+/ {
+	model = "Marvell Armada 38x family SoC";
+	compatible = "marvell,armada380";
+
+	aliases {
+		gpio0 = &gpio0;
+		gpio1 = &gpio1;
+		serial0 = &uart0;
+		serial1 = &uart1;
+	};
+
+	pmu {
+		compatible = "arm,cortex-a9-pmu";
+		interrupts-extended = <&mpic 3>;
+	};
+
+	soc {
+		compatible = "marvell,armada380-mbus", "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <1>;
+		controller = <&mbusc>;
+		interrupt-parent = <&gic>;
+		pcie-mem-aperture = <0xe0000000 0x8000000>;
+		pcie-io-aperture  = <0xe8000000 0x100000>;
+
+		bootrom {
+			compatible = "marvell,bootrom";
+			reg = <MBUS_ID(0x01, 0x1d) 0 0x200000>;
+		};
+
+		devbus-bootcs {
+			compatible = "marvell,mvebu-devbus";
+			reg = <MBUS_ID(0xf0, 0x01) 0x10400 0x8>;
+			ranges = <0 MBUS_ID(0x01, 0x2f) 0 0xffffffff>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&coreclk 0>;
+			status = "disabled";
+		};
+
+		devbus-cs0 {
+			compatible = "marvell,mvebu-devbus";
+			reg = <MBUS_ID(0xf0, 0x01) 0x10408 0x8>;
+			ranges = <0 MBUS_ID(0x01, 0x3e) 0 0xffffffff>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&coreclk 0>;
+			status = "disabled";
+		};
+
+		devbus-cs1 {
+			compatible = "marvell,mvebu-devbus";
+			reg = <MBUS_ID(0xf0, 0x01) 0x10410 0x8>;
+			ranges = <0 MBUS_ID(0x01, 0x3d) 0 0xffffffff>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&coreclk 0>;
+			status = "disabled";
+		};
+
+		devbus-cs2 {
+			compatible = "marvell,mvebu-devbus";
+			reg = <MBUS_ID(0xf0, 0x01) 0x10418 0x8>;
+			ranges = <0 MBUS_ID(0x01, 0x3b) 0 0xffffffff>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&coreclk 0>;
+			status = "disabled";
+		};
+
+		devbus-cs3 {
+			compatible = "marvell,mvebu-devbus";
+			reg = <MBUS_ID(0xf0, 0x01) 0x10420 0x8>;
+			ranges = <0 MBUS_ID(0x01, 0x37) 0 0xffffffff>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&coreclk 0>;
+			status = "disabled";
+		};
+
+		internal-regs {
+			compatible = "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 MBUS_ID(0xf0, 0x01) 0 0x100000>;
+
+			L2: cache-controller@8000 {
+				compatible = "arm,pl310-cache";
+				reg = <0x8000 0x1000>;
+				cache-unified;
+				cache-level = <2>;
+			};
+
+			scu@c000 {
+				compatible = "arm,cortex-a9-scu";
+				reg = <0xc000 0x58>;
+			};
+
+			timer@c600 {
+				compatible = "arm,cortex-a9-twd-timer";
+				reg = <0xc600 0x20>;
+				interrupts = <GIC_PPI 13 (IRQ_TYPE_EDGE_RISING | GIC_CPU_MASK_SIMPLE(2))>;
+				clocks = <&coreclk 2>;
+			};
+
+			gic: interrupt-controller@d000 {
+				compatible = "arm,cortex-a9-gic";
+				#interrupt-cells = <3>;
+				#size-cells = <0>;
+				interrupt-controller;
+				reg = <0xd000 0x1000>,
+				      <0xc100 0x100>;
+			};
+
+			spi0: spi@10600 {
+				compatible = "marvell,armada-380-spi",
+						"marvell,orion-spi";
+				reg = <0x10600 0x50>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				cell-index = <0>;
+				interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
+
+			spi1: spi@10680 {
+				compatible = "marvell,armada-380-spi",
+						"marvell,orion-spi";
+				reg = <0x10680 0x50>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				cell-index = <1>;
+				interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
+
+			i2c0: i2c@11000 {
+				compatible = "marvell,mv64xxx-i2c";
+				reg = <0x11000 0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+				timeout-ms = <1000>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
+
+			i2c1: i2c@11100 {
+				compatible = "marvell,mv64xxx-i2c";
+				reg = <0x11100 0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+				timeout-ms = <1000>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
+
+			uart0: serial@12000 {
+				compatible = "snps,dw-apb-uart";
+				reg = <0x12000 0x100>;
+				reg-shift = <2>;
+				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+				reg-io-width = <1>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
+
+			uart1: serial@12100 {
+				compatible = "snps,dw-apb-uart";
+				reg = <0x12100 0x100>;
+				reg-shift = <2>;
+				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+				reg-io-width = <1>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
+
+			pinctrl: pinctrl@18000 {
+				reg = <0x18000 0x20>;
+
+				ge0_rgmii_pins: ge-rgmii-pins-0 {
+					marvell,pins = "mpp6", "mpp7", "mpp8",
+						       "mpp9", "mpp10", "mpp11",
+						       "mpp12", "mpp13", "mpp14",
+						       "mpp15", "mpp16", "mpp17";
+					marvell,function = "ge0";
+				};
+
+				ge1_rgmii_pins: ge-rgmii-pins-1 {
+					marvell,pins = "mpp21", "mpp27", "mpp28",
+						       "mpp29", "mpp30", "mpp31",
+						       "mpp32", "mpp37", "mpp38",
+						       "mpp39", "mpp40", "mpp41";
+					marvell,function = "ge1";
+				};
+
+				i2c0_pins: i2c-pins-0 {
+					marvell,pins = "mpp2", "mpp3";
+					marvell,function = "i2c0";
+				};
+
+				mdio_pins: mdio-pins {
+					marvell,pins = "mpp4", "mpp5";
+					marvell,function = "ge";
+				};
+
+				ref_clk0_pins: ref-clk-pins-0 {
+					marvell,pins = "mpp45";
+					marvell,function = "ref";
+				};
+
+				ref_clk1_pins: ref-clk-pins-1 {
+					marvell,pins = "mpp46";
+					marvell,function = "ref";
+				};
+
+				spi0_pins: spi-pins-0 {
+					marvell,pins = "mpp22", "mpp23", "mpp24",
+						       "mpp25";
+					marvell,function = "spi0";
+				};
+
+				spi1_pins: spi-pins-1 {
+					marvell,pins = "mpp56", "mpp57", "mpp58",
+						       "mpp59";
+					marvell,function = "spi1";
+				};
+
+				uart0_pins: uart-pins-0 {
+					marvell,pins = "mpp0", "mpp1";
+					marvell,function = "ua0";
+				};
+
+				uart1_pins: uart-pins-1 {
+					marvell,pins = "mpp19", "mpp20";
+					marvell,function = "ua1";
+				};
+
+				sdhci_pins: sdhci-pins {
+					marvell,pins = "mpp48", "mpp49", "mpp50",
+						       "mpp52", "mpp53", "mpp54",
+						       "mpp55", "mpp57", "mpp58",
+						       "mpp59";
+					marvell,function = "sd0";
+				};
+
+				sata0_pins: sata-pins-0 {
+					marvell,pins = "mpp20";
+					marvell,function = "sata0";
+				};
+
+				sata1_pins: sata-pins-1 {
+					marvell,pins = "mpp19";
+					marvell,function = "sata1";
+				};
+
+				sata2_pins: sata-pins-2 {
+					marvell,pins = "mpp47";
+					marvell,function = "sata2";
+				};
+
+				sata3_pins: sata-pins-3 {
+					marvell,pins = "mpp44";
+					marvell,function = "sata3";
+				};
+			};
+
+			gpio0: gpio@18100 {
+				compatible = "marvell,orion-gpio";
+				reg = <0x18100 0x40>;
+				ngpios = <32>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			gpio1: gpio@18140 {
+				compatible = "marvell,orion-gpio";
+				reg = <0x18140 0x40>;
+				ngpios = <28>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			system-controller@18200 {
+				compatible = "marvell,armada-380-system-controller",
+					     "marvell,armada-370-xp-system-controller";
+				reg = <0x18200 0x100>;
+			};
+
+			gateclk: clock-gating-control@18220 {
+				compatible = "marvell,armada-380-gating-clock";
+				reg = <0x18220 0x4>;
+				clocks = <&coreclk 0>;
+				#clock-cells = <1>;
+			};
+
+			coreclk: mvebu-sar@18600 {
+				compatible = "marvell,armada-380-core-clock";
+				reg = <0x18600 0x04>;
+				#clock-cells = <1>;
+			};
+
+			mbusc: mbus-controller@20000 {
+				compatible = "marvell,mbus-controller";
+				reg = <0x20000 0x100>, <0x20180 0x20>;
+			};
+
+			mpic: interrupt-controller@20a00 {
+				compatible = "marvell,mpic";
+				reg = <0x20a00 0x2d0>, <0x21070 0x58>;
+				#interrupt-cells = <1>;
+				#size-cells = <1>;
+				interrupt-controller;
+				msi-controller;
+				interrupts = <GIC_PPI 15 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			timer@20300 {
+				compatible = "marvell,armada-380-timer",
+					     "marvell,armada-xp-timer";
+				reg = <0x20300 0x30>, <0x21040 0x30>;
+				interrupts-extended = <&gic  GIC_SPI  8 IRQ_TYPE_LEVEL_HIGH>,
+						      <&gic  GIC_SPI  9 IRQ_TYPE_LEVEL_HIGH>,
+						      <&gic  GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+						      <&gic  GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+						      <&mpic 5>,
+						      <&mpic 6>;
+				clocks = <&coreclk 2>, <&refclk>;
+				clock-names = "nbclk", "fixed";
+			};
+
+			watchdog@20300 {
+				compatible = "marvell,armada-380-wdt";
+				reg = <0x20300 0x34>, <0x20704 0x4>, <0x18260 0x4>;
+				clocks = <&coreclk 2>, <&refclk>;
+				clock-names = "nbclk", "fixed";
+			};
+
+			cpurst@20800 {
+				compatible = "marvell,armada-370-cpu-reset";
+				reg = <0x20800 0x10>;
+			};
+
+			mpcore-soc-ctrl@20d20 {
+				compatible = "marvell,armada-380-mpcore-soc-ctrl";
+				reg = <0x20d20 0x6c>;
+			};
+
+			coherency-fabric@21010 {
+				compatible = "marvell,armada-380-coherency-fabric";
+				reg = <0x21010 0x1c>;
+			};
+
+			pmsu@22000 {
+				compatible = "marvell,armada-380-pmsu";
+				reg = <0x22000 0x1000>;
+			};
+
+			eth1: ethernet@30000 {
+				compatible = "marvell,armada-370-neta";
+				reg = <0x30000 0x4000>;
+				interrupts-extended = <&mpic 10>;
+				clocks = <&gateclk 3>;
+				status = "disabled";
+			};
+
+			eth2: ethernet@34000 {
+				compatible = "marvell,armada-370-neta";
+				reg = <0x34000 0x4000>;
+				interrupts-extended = <&mpic 12>;
+				clocks = <&gateclk 2>;
+				status = "disabled";
+			};
+
+			usb@58000 {
+				compatible = "marvell,orion-ehci";
+				reg = <0x58000 0x500>;
+				interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gateclk 18>;
+				status = "disabled";
+			};
+
+			xor@60800 {
+				compatible = "marvell,orion-xor";
+				reg = <0x60800 0x100
+				       0x60a00 0x100>;
+				clocks = <&gateclk 22>;
+				status = "okay";
+
+				xor00 {
+					interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+					dmacap,memcpy;
+					dmacap,xor;
+				};
+				xor01 {
+					interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
+					dmacap,memcpy;
+					dmacap,xor;
+					dmacap,memset;
+				};
+			};
+
+			xor@60900 {
+				compatible = "marvell,orion-xor";
+				reg = <0x60900 0x100
+				       0x60b00 0x100>;
+				clocks = <&gateclk 28>;
+				status = "okay";
+
+				xor10 {
+					interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
+					dmacap,memcpy;
+					dmacap,xor;
+				};
+				xor11 {
+					interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
+					dmacap,memcpy;
+					dmacap,xor;
+					dmacap,memset;
+				};
+			};
+
+			eth0: ethernet@70000 {
+				compatible = "marvell,armada-370-neta";
+				reg = <0x70000 0x4000>;
+				interrupts-extended = <&mpic 8>;
+				clocks = <&gateclk 4>;
+				status = "disabled";
+			};
+
+			mdio: mdio@72004 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "marvell,orion-mdio";
+				reg = <0x72004 0x4>;
+				clocks = <&gateclk 4>;
+			};
+
+			rtc@a3800 {
+				compatible = "marvell,armada-380-rtc";
+				reg = <0xa3800 0x20>, <0x184a0 0x0c>;
+				reg-names = "rtc", "rtc-soc";
+				interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			sata@a8000 {
+				compatible = "marvell,armada-380-ahci";
+				reg = <0xa8000 0x2000>;
+				interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gateclk 15>;
+				status = "disabled";
+			};
+
+			sata@e0000 {
+				compatible = "marvell,armada-380-ahci";
+				reg = <0xe0000 0x2000>;
+				interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gateclk 30>;
+				status = "disabled";
+			};
+
+			coredivclk: clock@e4250 {
+				compatible = "marvell,armada-380-corediv-clock";
+				reg = <0xe4250 0xc>;
+				#clock-cells = <1>;
+				clocks = <&mainpll>;
+				clock-output-names = "nand";
+			};
+
+			thermal@e8078 {
+				compatible = "marvell,armada380-thermal";
+				reg = <0xe4078 0x4>, <0xe4074 0x4>;
+				status = "okay";
+			};
+
+			flash@d0000 {
+				compatible = "marvell,armada370-nand";
+				reg = <0xd0000 0x54>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&coredivclk 0>;
+				status = "disabled";
+			};
+
+			sdhci@d8000 {
+				compatible = "marvell,armada-380-sdhci";
+				reg-names = "sdhci", "mbus", "conf-sdio3";
+				reg = <0xd8000 0x1000>,
+					<0xdc000 0x100>,
+					<0x18454 0x4>;
+				interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gateclk 17>;
+				mrvl,clk-delay-cycles = <0x1F>;
+				status = "disabled";
+			};
+
+			usb3@f0000 {
+				compatible = "marvell,armada-380-xhci";
+				reg = <0xf0000 0x4000>,<0xf4000 0x4000>;
+				interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gateclk 9>;
+				status = "disabled";
+			};
+
+			usb3@f8000 {
+				compatible = "marvell,armada-380-xhci";
+				reg = <0xf8000 0x4000>,<0xfc000 0x4000>;
+				interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gateclk 10>;
+				status = "disabled";
+			};
+		};
+	};
+
+	clocks {
+		/* 2 GHz fixed main PLL */
+		mainpll: mainpll {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <1000000000>;
+		};
+
+		/* 25 MHz reference crystal */
+		refclk: oscillator {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <25000000>;
+		};
+	};
+};

arch/arm/dts/armada-xp-gp.dts

@@ -0,0 +1,245 @@
+/*
+ * Device Tree file for Marvell Armada XP development board
+ * (DB-MV784MP-GP)
+ *
+ * Copyright (C) 2013-2014 Marvell
+ *
+ * Lior Amsalem <alior@marvell.com>
+ * Gregory CLEMENT <gregory.clement@free-electrons.com>
+ * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Note: this Device Tree assumes that the bootloader has remapped the
+ * internal registers to 0xf1000000 (instead of the default
+ * 0xd0000000). The 0xf1000000 is the default used by the recent,
+ * DT-capable, U-Boot bootloaders provided by Marvell. Some earlier
+ * boards were delivered with an older version of the bootloader that
+ * left internal registers mapped at 0xd0000000. If you are in this
+ * situation, you should either update your bootloader (preferred
+ * solution) or the below Device Tree should be adjusted.
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include "armada-xp-mv78460.dtsi"
+
+/ {
+	model = "Marvell Armada XP Development Board DB-MV784MP-GP";
+	compatible = "marvell,axp-gp", "marvell,armadaxp-mv78460", "marvell,armadaxp", "marvell,armada-370-xp";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory {
+		device_type = "memory";
+		/*
+                 * 8 GB of plug-in RAM modules by default.The amount
+                 * of memory available can be changed by the
+                 * bootloader according the size of the module
+                 * actually plugged. However, memory between
+                 * 0xF0000000 to 0xFFFFFFFF cannot be used, as it is
+                 * the address range used for I/O (internal registers,
+                 * MBus windows).
+		 */
+		reg = <0x00000000 0x00000000 0x00000000 0xf0000000>,
+		      <0x00000001 0x00000000 0x00000001 0x00000000>;
+	};
+
+	cpus {
+		pm_pic {
+			ctrl-gpios = <&gpio0 16 GPIO_ACTIVE_LOW>,
+				     <&gpio0 17 GPIO_ACTIVE_LOW>,
+				     <&gpio0 18 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000
+			  MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000
+			  MBUS_ID(0x01, 0x2f) 0 0 0xf0000000 0x1000000>;
+
+		devbus-bootcs {
+			status = "okay";
+
+			/* Device Bus parameters are required */
+
+			/* Read parameters */
+			devbus,bus-width    = <16>;
+			devbus,turn-off-ps  = <60000>;
+			devbus,badr-skew-ps = <0>;
+			devbus,acc-first-ps = <124000>;
+			devbus,acc-next-ps  = <248000>;
+			devbus,rd-setup-ps  = <0>;
+			devbus,rd-hold-ps   = <0>;
+
+			/* Write parameters */
+			devbus,sync-enable = <0>;
+			devbus,wr-high-ps  = <60000>;
+			devbus,wr-low-ps   = <60000>;
+			devbus,ale-wr-ps   = <60000>;
+
+			/* NOR 16 MiB */
+			nor@0 {
+				compatible = "cfi-flash";
+				reg = <0 0x1000000>;
+				bank-width = <2>;
+			};
+		};
+
+		pcie-controller {
+			status = "okay";
+
+			/*
+			 * The 3 slots are physically present as
+			 * standard PCIe slots on the board.
+			 */
+			pcie@1,0 {
+				/* Port 0, Lane 0 */
+				status = "okay";
+			};
+			pcie@9,0 {
+				/* Port 2, Lane 0 */
+				status = "okay";
+			};
+			pcie@10,0 {
+				/* Port 3, Lane 0 */
+				status = "okay";
+			};
+		};
+
+		internal-regs {
+			serial@12000 {
+				status = "okay";
+			};
+			serial@12100 {
+				status = "okay";
+			};
+			serial@12200 {
+				status = "okay";
+			};
+			serial@12300 {
+				status = "okay";
+			};
+			pinctrl {
+				pinctrl-0 = <&pic_pins>;
+				pinctrl-names = "default";
+				pic_pins: pic-pins-0 {
+					marvell,pins = "mpp16", "mpp17",
+						       "mpp18";
+					marvell,function = "gpio";
+				};
+			};
+			sata@a0000 {
+				nr-ports = <2>;
+				status = "okay";
+			};
+
+			mdio {
+				phy0: ethernet-phy@0 {
+					reg = <16>;
+				};
+
+				phy1: ethernet-phy@1 {
+					reg = <17>;
+				};
+
+				phy2: ethernet-phy@2 {
+					reg = <18>;
+				};
+
+				phy3: ethernet-phy@3 {
+					reg = <19>;
+				};
+			};
+
+			ethernet@70000 {
+				status = "okay";
+				phy = <&phy0>;
+				phy-mode = "qsgmii";
+			};
+			ethernet@74000 {
+				status = "okay";
+				phy = <&phy1>;
+				phy-mode = "qsgmii";
+			};
+			ethernet@30000 {
+				status = "okay";
+				phy = <&phy2>;
+				phy-mode = "qsgmii";
+			};
+			ethernet@34000 {
+				status = "okay";
+				phy = <&phy3>;
+				phy-mode = "qsgmii";
+			};
+
+			/* Front-side USB slot */
+			usb@50000 {
+				status = "okay";
+			};
+
+			/* Back-side USB slot */
+			usb@51000 {
+				status = "okay";
+			};
+
+			spi0: spi@10600 {
+				status = "okay";
+
+				spi-flash@0 {
+					#address-cells = <1>;
+					#size-cells = <1>;
+					compatible = "n25q128a13", "jedec,spi-nor";
+					reg = <0>; /* Chip select 0 */
+					spi-max-frequency = <108000000>;
+				};
+			};
+
+			nand@d0000 {
+				status = "okay";
+				num-cs = <1>;
+				marvell,nand-keep-config;
+				marvell,nand-enable-arbiter;
+				nand-on-flash-bbt;
+			};
+		};
+	};
+};

arch/arm/dts/armada-xp-mv78230.dtsi

@@ -0,0 +1,231 @@
+/*
+ * Device Tree Include file for Marvell Armada XP family SoC
+ *
+ * Copyright (C) 2012 Marvell
+ *
+ * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Contains definitions specific to the Armada XP MV78230 SoC that are not
+ * common to all Armada XP SoCs.
+ */
+
+#include "armada-xp.dtsi"
+
+/ {
+	model = "Marvell Armada XP MV78230 SoC";
+	compatible = "marvell,armadaxp-mv78230", "marvell,armadaxp", "marvell,armada-370-xp";
+
+	aliases {
+		gpio0 = &gpio0;
+		gpio1 = &gpio1;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		enable-method = "marvell,armada-xp-smp";
+
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "marvell,sheeva-v7";
+			reg = <0>;
+			clocks = <&cpuclk 0>;
+			clock-latency = <1000000>;
+		};
+
+		cpu@1 {
+			device_type = "cpu";
+			compatible = "marvell,sheeva-v7";
+			reg = <1>;
+			clocks = <&cpuclk 1>;
+			clock-latency = <1000000>;
+		};
+	};
+
+	soc {
+		/*
+		 * MV78230 has 2 PCIe units Gen2.0: One unit can be
+		 * configured as x4 or quad x1 lanes. One unit is
+		 * x1 only.
+		 */
+		pcie-controller {
+			compatible = "marvell,armada-xp-pcie";
+			status = "disabled";
+			device_type = "pci";
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			msi-parent = <&mpic>;
+			bus-range = <0x00 0xff>;
+
+			ranges =
+			       <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000   /* Port 0.0 registers */
+				0x82000000 0 0x44000 MBUS_ID(0xf0, 0x01) 0x44000 0 0x00002000   /* Port 0.1 registers */
+				0x82000000 0 0x48000 MBUS_ID(0xf0, 0x01) 0x48000 0 0x00002000   /* Port 0.2 registers */
+				0x82000000 0 0x4c000 MBUS_ID(0xf0, 0x01) 0x4c000 0 0x00002000   /* Port 0.3 registers */
+				0x82000000 0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x00002000   /* Port 1.0 registers */
+				0x82000000 0x1 0       MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 MEM */
+				0x81000000 0x1 0       MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 IO  */
+				0x82000000 0x2 0       MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 0.1 MEM */
+				0x81000000 0x2 0       MBUS_ID(0x04, 0xd0) 0 1 0 /* Port 0.1 IO  */
+				0x82000000 0x3 0       MBUS_ID(0x04, 0xb8) 0 1 0 /* Port 0.2 MEM */
+				0x81000000 0x3 0       MBUS_ID(0x04, 0xb0) 0 1 0 /* Port 0.2 IO  */
+				0x82000000 0x4 0       MBUS_ID(0x04, 0x78) 0 1 0 /* Port 0.3 MEM */
+				0x81000000 0x4 0       MBUS_ID(0x04, 0x70) 0 1 0 /* Port 0.3 IO  */
+				0x82000000 0x5 0       MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 1.0 MEM */
+				0x81000000 0x5 0       MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 1.0 IO  */>;
+
+			pcie@1,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+				reg = <0x0800 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
+					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 58>;
+				marvell,pcie-port = <0>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 5>;
+				status = "disabled";
+			};
+
+			pcie@2,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
+				reg = <0x1000 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
+					  0x81000000 0 0 0x81000000 0x2 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 59>;
+				marvell,pcie-port = <0>;
+				marvell,pcie-lane = <1>;
+				clocks = <&gateclk 6>;
+				status = "disabled";
+			};
+
+			pcie@3,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x48000 0 0x2000>;
+				reg = <0x1800 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0
+					  0x81000000 0 0 0x81000000 0x3 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 60>;
+				marvell,pcie-port = <0>;
+				marvell,pcie-lane = <2>;
+				clocks = <&gateclk 7>;
+				status = "disabled";
+			};
+
+			pcie@4,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x4c000 0 0x2000>;
+				reg = <0x2000 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0
+					  0x81000000 0 0 0x81000000 0x4 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 61>;
+				marvell,pcie-port = <0>;
+				marvell,pcie-lane = <3>;
+				clocks = <&gateclk 8>;
+				status = "disabled";
+			};
+
+			pcie@5,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x80000 0 0x2000>;
+				reg = <0x2800 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x5 0 1 0
+					  0x81000000 0 0 0x81000000 0x5 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 62>;
+				marvell,pcie-port = <1>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 9>;
+				status = "disabled";
+			};
+		};
+
+		internal-regs {
+			gpio0: gpio@18100 {
+				compatible = "marvell,orion-gpio";
+				reg = <0x18100 0x40>;
+				ngpios = <32>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				interrupts = <82>, <83>, <84>, <85>;
+			};
+
+			gpio1: gpio@18140 {
+				compatible = "marvell,orion-gpio";
+				reg = <0x18140 0x40>;
+				ngpios = <17>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				interrupts = <87>, <88>, <89>;
+			};
+		};
+	};
+};
+
+&pinctrl {
+	compatible = "marvell,mv78230-pinctrl";
+};

arch/arm/dts/armada-xp-mv78260.dtsi

@@ -0,0 +1,333 @@
+/*
+ * Device Tree Include file for Marvell Armada XP family SoC
+ *
+ * Copyright (C) 2012 Marvell
+ *
+ * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Contains definitions specific to the Armada XP MV78260 SoC that are not
+ * common to all Armada XP SoCs.
+ */
+
+#include "armada-xp.dtsi"
+
+/ {
+	model = "Marvell Armada XP MV78260 SoC";
+	compatible = "marvell,armadaxp-mv78260", "marvell,armadaxp", "marvell,armada-370-xp";
+
+	aliases {
+		gpio0 = &gpio0;
+		gpio1 = &gpio1;
+		gpio2 = &gpio2;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		enable-method = "marvell,armada-xp-smp";
+
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "marvell,sheeva-v7";
+			reg = <0>;
+			clocks = <&cpuclk 0>;
+			clock-latency = <1000000>;
+		};
+
+		cpu@1 {
+			device_type = "cpu";
+			compatible = "marvell,sheeva-v7";
+			reg = <1>;
+			clocks = <&cpuclk 1>;
+			clock-latency = <1000000>;
+		};
+	};
+
+	soc {
+		/*
+		 * MV78260 has 3 PCIe units Gen2.0: Two units can be
+		 * configured as x4 or quad x1 lanes. One unit is
+		 * x4 only.
+		 */
+		pcie-controller {
+			compatible = "marvell,armada-xp-pcie";
+			status = "disabled";
+			device_type = "pci";
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			msi-parent = <&mpic>;
+			bus-range = <0x00 0xff>;
+
+			ranges =
+			       <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000   /* Port 0.0 registers */
+				0x82000000 0 0x42000 MBUS_ID(0xf0, 0x01) 0x42000 0 0x00002000   /* Port 2.0 registers */
+				0x82000000 0 0x44000 MBUS_ID(0xf0, 0x01) 0x44000 0 0x00002000   /* Port 0.1 registers */
+				0x82000000 0 0x48000 MBUS_ID(0xf0, 0x01) 0x48000 0 0x00002000   /* Port 0.2 registers */
+				0x82000000 0 0x4c000 MBUS_ID(0xf0, 0x01) 0x4c000 0 0x00002000   /* Port 0.3 registers */
+				0x82000000 0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x00002000   /* Port 1.0 registers */
+				0x82000000 0 0x84000 MBUS_ID(0xf0, 0x01) 0x84000 0 0x00002000   /* Port 1.1 registers */
+				0x82000000 0 0x88000 MBUS_ID(0xf0, 0x01) 0x88000 0 0x00002000   /* Port 1.2 registers */
+				0x82000000 0 0x8c000 MBUS_ID(0xf0, 0x01) 0x8c000 0 0x00002000   /* Port 1.3 registers */
+				0x82000000 0x1 0     MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 MEM */
+				0x81000000 0x1 0     MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 IO  */
+				0x82000000 0x2 0     MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 0.1 MEM */
+				0x81000000 0x2 0     MBUS_ID(0x04, 0xd0) 0 1 0 /* Port 0.1 IO  */
+				0x82000000 0x3 0     MBUS_ID(0x04, 0xb8) 0 1 0 /* Port 0.2 MEM */
+				0x81000000 0x3 0     MBUS_ID(0x04, 0xb0) 0 1 0 /* Port 0.2 IO  */
+				0x82000000 0x4 0     MBUS_ID(0x04, 0x78) 0 1 0 /* Port 0.3 MEM */
+				0x81000000 0x4 0     MBUS_ID(0x04, 0x70) 0 1 0 /* Port 0.3 IO  */
+
+				0x82000000 0x5 0     MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 1.0 MEM */
+				0x81000000 0x5 0     MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 1.0 IO  */
+				0x82000000 0x6 0     MBUS_ID(0x08, 0xd8) 0 1 0 /* Port 1.1 MEM */
+				0x81000000 0x6 0     MBUS_ID(0x08, 0xd0) 0 1 0 /* Port 1.1 IO  */
+				0x82000000 0x7 0     MBUS_ID(0x08, 0xb8) 0 1 0 /* Port 1.2 MEM */
+				0x81000000 0x7 0     MBUS_ID(0x08, 0xb0) 0 1 0 /* Port 1.2 IO  */
+				0x82000000 0x8 0     MBUS_ID(0x08, 0x78) 0 1 0 /* Port 1.3 MEM */
+				0x81000000 0x8 0     MBUS_ID(0x08, 0x70) 0 1 0 /* Port 1.3 IO  */
+
+				0x82000000 0x9 0     MBUS_ID(0x04, 0xf8) 0 1 0 /* Port 2.0 MEM */
+				0x81000000 0x9 0     MBUS_ID(0x04, 0xf0) 0 1 0 /* Port 2.0 IO  */>;
+
+			pcie@1,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+				reg = <0x0800 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
+					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 58>;
+				marvell,pcie-port = <0>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 5>;
+				status = "disabled";
+			};
+
+			pcie@2,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
+				reg = <0x1000 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
+					  0x81000000 0 0 0x81000000 0x2 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 59>;
+				marvell,pcie-port = <0>;
+				marvell,pcie-lane = <1>;
+				clocks = <&gateclk 6>;
+				status = "disabled";
+			};
+
+			pcie@3,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x48000 0 0x2000>;
+				reg = <0x1800 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0
+					  0x81000000 0 0 0x81000000 0x3 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 60>;
+				marvell,pcie-port = <0>;
+				marvell,pcie-lane = <2>;
+				clocks = <&gateclk 7>;
+				status = "disabled";
+			};
+
+			pcie@4,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x4c000 0 0x2000>;
+				reg = <0x2000 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0
+					  0x81000000 0 0 0x81000000 0x4 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 61>;
+				marvell,pcie-port = <0>;
+				marvell,pcie-lane = <3>;
+				clocks = <&gateclk 8>;
+				status = "disabled";
+			};
+
+			pcie@5,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x80000 0 0x2000>;
+				reg = <0x2800 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x5 0 1 0
+					  0x81000000 0 0 0x81000000 0x5 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 62>;
+				marvell,pcie-port = <1>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 9>;
+				status = "disabled";
+			};
+
+			pcie@6,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x84000 0 0x2000>;
+				reg = <0x3000 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x6 0 1 0
+					  0x81000000 0 0 0x81000000 0x6 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 63>;
+				marvell,pcie-port = <1>;
+				marvell,pcie-lane = <1>;
+				clocks = <&gateclk 10>;
+				status = "disabled";
+			};
+
+			pcie@7,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x88000 0 0x2000>;
+				reg = <0x3800 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x7 0 1 0
+					  0x81000000 0 0 0x81000000 0x7 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 64>;
+				marvell,pcie-port = <1>;
+				marvell,pcie-lane = <2>;
+				clocks = <&gateclk 11>;
+				status = "disabled";
+			};
+
+			pcie@8,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x8c000 0 0x2000>;
+				reg = <0x4000 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x8 0 1 0
+					  0x81000000 0 0 0x81000000 0x8 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 65>;
+				marvell,pcie-port = <1>;
+				marvell,pcie-lane = <3>;
+				clocks = <&gateclk 12>;
+				status = "disabled";
+			};
+
+			pcie@9,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x42000 0 0x2000>;
+				reg = <0x4800 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x9 0 1 0
+					  0x81000000 0 0 0x81000000 0x9 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 99>;
+				marvell,pcie-port = <2>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 26>;
+				status = "disabled";
+			};
+		};
+
+		internal-regs {
+			gpio0: gpio@18100 {
+				compatible = "marvell,orion-gpio";
+				reg = <0x18100 0x40>;
+				ngpios = <32>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				interrupts = <82>, <83>, <84>, <85>;
+			};
+
+			gpio1: gpio@18140 {
+				compatible = "marvell,orion-gpio";
+				reg = <0x18140 0x40>;
+				ngpios = <32>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				interrupts = <87>, <88>, <89>, <90>;
+			};
+
+			gpio2: gpio@18180 {
+				compatible = "marvell,orion-gpio";
+				reg = <0x18180 0x40>;
+				ngpios = <3>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				interrupts = <91>;
+			};
+
+			eth3: ethernet@34000 {
+				compatible = "marvell,armada-xp-neta";
+				reg = <0x34000 0x4000>;
+				interrupts = <14>;
+				clocks = <&gateclk 1>;
+				status = "disabled";
+			};
+		};
+	};
+};
+
+&pinctrl {
+	compatible = "marvell,mv78260-pinctrl";
+};

arch/arm/dts/armada-xp-mv78460.dtsi

@@ -0,0 +1,371 @@
+/*
+ * Device Tree Include file for Marvell Armada XP family SoC
+ *
+ * Copyright (C) 2012 Marvell
+ *
+ * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Contains definitions specific to the Armada XP MV78460 SoC that are not
+ * common to all Armada XP SoCs.
+ */
+
+#include "armada-xp.dtsi"
+
+/ {
+	model = "Marvell Armada XP MV78460 SoC";
+	compatible = "marvell,armadaxp-mv78460", "marvell,armadaxp", "marvell,armada-370-xp";
+
+	aliases {
+		gpio0 = &gpio0;
+		gpio1 = &gpio1;
+		gpio2 = &gpio2;
+	};
+
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		enable-method = "marvell,armada-xp-smp";
+
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "marvell,sheeva-v7";
+			reg = <0>;
+			clocks = <&cpuclk 0>;
+			clock-latency = <1000000>;
+		};
+
+		cpu@1 {
+			device_type = "cpu";
+			compatible = "marvell,sheeva-v7";
+			reg = <1>;
+			clocks = <&cpuclk 1>;
+			clock-latency = <1000000>;
+		};
+
+		cpu@2 {
+			device_type = "cpu";
+			compatible = "marvell,sheeva-v7";
+			reg = <2>;
+			clocks = <&cpuclk 2>;
+			clock-latency = <1000000>;
+		};
+
+		cpu@3 {
+			device_type = "cpu";
+			compatible = "marvell,sheeva-v7";
+			reg = <3>;
+			clocks = <&cpuclk 3>;
+			clock-latency = <1000000>;
+		};
+	};
+
+	soc {
+		/*
+		 * MV78460 has 4 PCIe units Gen2.0: Two units can be
+		 * configured as x4 or quad x1 lanes. Two units are
+		 * x4/x1.
+		 */
+		pcie-controller {
+			compatible = "marvell,armada-xp-pcie";
+			status = "disabled";
+			device_type = "pci";
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			msi-parent = <&mpic>;
+			bus-range = <0x00 0xff>;
+
+			ranges =
+			       <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000   /* Port 0.0 registers */
+				0x82000000 0 0x42000 MBUS_ID(0xf0, 0x01) 0x42000 0 0x00002000   /* Port 2.0 registers */
+				0x82000000 0 0x44000 MBUS_ID(0xf0, 0x01) 0x44000 0 0x00002000   /* Port 0.1 registers */
+				0x82000000 0 0x48000 MBUS_ID(0xf0, 0x01) 0x48000 0 0x00002000   /* Port 0.2 registers */
+				0x82000000 0 0x4c000 MBUS_ID(0xf0, 0x01) 0x4c000 0 0x00002000   /* Port 0.3 registers */
+				0x82000000 0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x00002000   /* Port 1.0 registers */
+				0x82000000 0 0x82000 MBUS_ID(0xf0, 0x01) 0x82000 0 0x00002000   /* Port 3.0 registers */
+				0x82000000 0 0x84000 MBUS_ID(0xf0, 0x01) 0x84000 0 0x00002000   /* Port 1.1 registers */
+				0x82000000 0 0x88000 MBUS_ID(0xf0, 0x01) 0x88000 0 0x00002000   /* Port 1.2 registers */
+				0x82000000 0 0x8c000 MBUS_ID(0xf0, 0x01) 0x8c000 0 0x00002000   /* Port 1.3 registers */
+				0x82000000 0x1 0     MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 MEM */
+				0x81000000 0x1 0     MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 IO  */
+				0x82000000 0x2 0     MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 0.1 MEM */
+				0x81000000 0x2 0     MBUS_ID(0x04, 0xd0) 0 1 0 /* Port 0.1 IO  */
+				0x82000000 0x3 0     MBUS_ID(0x04, 0xb8) 0 1 0 /* Port 0.2 MEM */
+				0x81000000 0x3 0     MBUS_ID(0x04, 0xb0) 0 1 0 /* Port 0.2 IO  */
+				0x82000000 0x4 0     MBUS_ID(0x04, 0x78) 0 1 0 /* Port 0.3 MEM */
+				0x81000000 0x4 0     MBUS_ID(0x04, 0x70) 0 1 0 /* Port 0.3 IO  */
+
+				0x82000000 0x5 0     MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 1.0 MEM */
+				0x81000000 0x5 0     MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 1.0 IO  */
+				0x82000000 0x6 0     MBUS_ID(0x08, 0xd8) 0 1 0 /* Port 1.1 MEM */
+				0x81000000 0x6 0     MBUS_ID(0x08, 0xd0) 0 1 0 /* Port 1.1 IO  */
+				0x82000000 0x7 0     MBUS_ID(0x08, 0xb8) 0 1 0 /* Port 1.2 MEM */
+				0x81000000 0x7 0     MBUS_ID(0x08, 0xb0) 0 1 0 /* Port 1.2 IO  */
+				0x82000000 0x8 0     MBUS_ID(0x08, 0x78) 0 1 0 /* Port 1.3 MEM */
+				0x81000000 0x8 0     MBUS_ID(0x08, 0x70) 0 1 0 /* Port 1.3 IO  */
+
+				0x82000000 0x9 0     MBUS_ID(0x04, 0xf8) 0 1 0 /* Port 2.0 MEM */
+				0x81000000 0x9 0     MBUS_ID(0x04, 0xf0) 0 1 0 /* Port 2.0 IO  */
+
+				0x82000000 0xa 0     MBUS_ID(0x08, 0xf8) 0 1 0 /* Port 3.0 MEM */
+				0x81000000 0xa 0     MBUS_ID(0x08, 0xf0) 0 1 0 /* Port 3.0 IO  */>;
+
+			pcie@1,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+				reg = <0x0800 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
+					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 58>;
+				marvell,pcie-port = <0>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 5>;
+				status = "disabled";
+			};
+
+			pcie@2,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82001000 0 0x44000 0 0x2000>;
+				reg = <0x1000 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
+					  0x81000000 0 0 0x81000000 0x2 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 59>;
+				marvell,pcie-port = <0>;
+				marvell,pcie-lane = <1>;
+				clocks = <&gateclk 6>;
+				status = "disabled";
+			};
+
+			pcie@3,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82001800 0 0x48000 0 0x2000>;
+				reg = <0x1800 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0
+					  0x81000000 0 0 0x81000000 0x3 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 60>;
+				marvell,pcie-port = <0>;
+				marvell,pcie-lane = <2>;
+				clocks = <&gateclk 7>;
+				status = "disabled";
+			};
+
+			pcie@4,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82002000 0 0x4c000 0 0x2000>;
+				reg = <0x2000 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0
+					  0x81000000 0 0 0x81000000 0x4 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 61>;
+				marvell,pcie-port = <0>;
+				marvell,pcie-lane = <3>;
+				clocks = <&gateclk 8>;
+				status = "disabled";
+			};
+
+			pcie@5,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82002800 0 0x80000 0 0x2000>;
+				reg = <0x2800 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x5 0 1 0
+					  0x81000000 0 0 0x81000000 0x5 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 62>;
+				marvell,pcie-port = <1>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 9>;
+				status = "disabled";
+			};
+
+			pcie@6,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82003000 0 0x84000 0 0x2000>;
+				reg = <0x3000 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x6 0 1 0
+					  0x81000000 0 0 0x81000000 0x6 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 63>;
+				marvell,pcie-port = <1>;
+				marvell,pcie-lane = <1>;
+				clocks = <&gateclk 10>;
+				status = "disabled";
+			};
+
+			pcie@7,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82003800 0 0x88000 0 0x2000>;
+				reg = <0x3800 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x7 0 1 0
+					  0x81000000 0 0 0x81000000 0x7 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 64>;
+				marvell,pcie-port = <1>;
+				marvell,pcie-lane = <2>;
+				clocks = <&gateclk 11>;
+				status = "disabled";
+			};
+
+			pcie@8,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82004000 0 0x8c000 0 0x2000>;
+				reg = <0x4000 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x8 0 1 0
+					  0x81000000 0 0 0x81000000 0x8 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 65>;
+				marvell,pcie-port = <1>;
+				marvell,pcie-lane = <3>;
+				clocks = <&gateclk 12>;
+				status = "disabled";
+			};
+
+			pcie@9,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82004800 0 0x42000 0 0x2000>;
+				reg = <0x4800 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x9 0 1 0
+					  0x81000000 0 0 0x81000000 0x9 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 99>;
+				marvell,pcie-port = <2>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 26>;
+				status = "disabled";
+			};
+
+			pcie@10,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82005000 0 0x82000 0 0x2000>;
+				reg = <0x5000 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0xa 0 1 0
+					  0x81000000 0 0 0x81000000 0xa 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 103>;
+				marvell,pcie-port = <3>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 27>;
+				status = "disabled";
+			};
+		};
+
+		internal-regs {
+			gpio0: gpio@18100 {
+				compatible = "marvell,orion-gpio";
+				reg = <0x18100 0x40>;
+				ngpios = <32>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				interrupts = <82>, <83>, <84>, <85>;
+			};
+
+			gpio1: gpio@18140 {
+				compatible = "marvell,orion-gpio";
+				reg = <0x18140 0x40>;
+				ngpios = <32>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				interrupts = <87>, <88>, <89>, <90>;
+			};
+
+			gpio2: gpio@18180 {
+				compatible = "marvell,orion-gpio";
+				reg = <0x18180 0x40>;
+				ngpios = <3>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				interrupts = <91>;
+			};
+
+			eth3: ethernet@34000 {
+				compatible = "marvell,armada-xp-neta";
+				reg = <0x34000 0x4000>;
+				interrupts = <14>;
+				clocks = <&gateclk 1>;
+				status = "disabled";
+			};
+		};
+	};
+};
+
+&pinctrl {
+	compatible = "marvell,mv78460-pinctrl";
+};

arch/arm/dts/armada-xp.dtsi

@@ -0,0 +1,320 @@
+/*
+ * Device Tree Include file for Marvell Armada XP family SoC
+ *
+ * Copyright (C) 2012 Marvell
+ *
+ * Lior Amsalem <alior@marvell.com>
+ * Gregory CLEMENT <gregory.clement@free-electrons.com>
+ * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ * Ben Dooks <ben.dooks@codethink.co.uk>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Contains definitions specific to the Armada XP SoC that are not
+ * common to all Armada SoCs.
+ */
+
+#include "armada-370-xp.dtsi"
+
+/ {
+	model = "Marvell Armada XP family SoC";
+	compatible = "marvell,armadaxp", "marvell,armada-370-xp";
+
+	aliases {
+		serial2 = &uart2;
+		serial3 = &uart3;
+	};
+
+	soc {
+		compatible = "marvell,armadaxp-mbus", "simple-bus";
+
+		bootrom {
+			compatible = "marvell,bootrom";
+			reg = <MBUS_ID(0x01, 0x1d) 0 0x100000>;
+		};
+
+		internal-regs {
+			sdramc@1400 {
+				compatible = "marvell,armada-xp-sdram-controller";
+				reg = <0x1400 0x500>;
+			};
+
+			L2: l2-cache {
+				compatible = "marvell,aurora-system-cache";
+				reg = <0x08000 0x1000>;
+				cache-id-part = <0x100>;
+				cache-level = <2>;
+				cache-unified;
+				wt-override;
+			};
+
+			spi0: spi@10600 {
+				compatible = "marvell,armada-xp-spi",
+						"marvell,orion-spi";
+				pinctrl-0 = <&spi0_pins>;
+				pinctrl-names = "default";
+			};
+
+			spi1: spi@10680 {
+				compatible = "marvell,armada-xp-spi",
+						"marvell,orion-spi";
+			};
+
+
+			i2c0: i2c@11000 {
+				compatible = "marvell,mv78230-i2c", "marvell,mv64xxx-i2c";
+				reg = <0x11000 0x100>;
+			};
+
+			i2c1: i2c@11100 {
+				compatible = "marvell,mv78230-i2c", "marvell,mv64xxx-i2c";
+				reg = <0x11100 0x100>;
+			};
+
+			uart2: serial@12200 {
+				compatible = "snps,dw-apb-uart";
+				pinctrl-0 = <&uart2_pins>;
+				pinctrl-names = "default";
+				reg = <0x12200 0x100>;
+				reg-shift = <2>;
+				interrupts = <43>;
+				reg-io-width = <1>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
+
+			uart3: serial@12300 {
+				compatible = "snps,dw-apb-uart";
+				pinctrl-0 = <&uart3_pins>;
+				pinctrl-names = "default";
+				reg = <0x12300 0x100>;
+				reg-shift = <2>;
+				interrupts = <44>;
+				reg-io-width = <1>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
+
+			system-controller@18200 {
+				compatible = "marvell,armada-370-xp-system-controller";
+				reg = <0x18200 0x500>;
+			};
+
+			gateclk: clock-gating-control@18220 {
+				compatible = "marvell,armada-xp-gating-clock";
+				reg = <0x18220 0x4>;
+				clocks = <&coreclk 0>;
+				#clock-cells = <1>;
+			};
+
+			coreclk: mvebu-sar@18230 {
+				compatible = "marvell,armada-xp-core-clock";
+				reg = <0x18230 0x08>;
+				#clock-cells = <1>;
+			};
+
+			thermal@182b0 {
+				compatible = "marvell,armadaxp-thermal";
+				reg = <0x182b0 0x4
+					0x184d0 0x4>;
+				status = "okay";
+			};
+
+			cpuclk: clock-complex@18700 {
+				#clock-cells = <1>;
+				compatible = "marvell,armada-xp-cpu-clock";
+				reg = <0x18700 0x24>, <0x1c054 0x10>;
+				clocks = <&coreclk 1>;
+			};
+
+			interrupt-controller@20a00 {
+			      reg = <0x20a00 0x2d0>, <0x21070 0x58>;
+			};
+
+			timer@20300 {
+				compatible = "marvell,armada-xp-timer";
+				clocks = <&coreclk 2>, <&refclk>;
+				clock-names = "nbclk", "fixed";
+			};
+
+			watchdog@20300 {
+				compatible = "marvell,armada-xp-wdt";
+				clocks = <&coreclk 2>, <&refclk>;
+				clock-names = "nbclk", "fixed";
+			};
+
+			cpurst@20800 {
+				compatible = "marvell,armada-370-cpu-reset";
+				reg = <0x20800 0x20>;
+			};
+
+			eth2: ethernet@30000 {
+				compatible = "marvell,armada-xp-neta";
+				reg = <0x30000 0x4000>;
+				interrupts = <12>;
+				clocks = <&gateclk 2>;
+				status = "disabled";
+			};
+
+			usb@50000 {
+				clocks = <&gateclk 18>;
+			};
+
+			usb@51000 {
+				clocks = <&gateclk 19>;
+			};
+
+			usb@52000 {
+				compatible = "marvell,orion-ehci";
+				reg = <0x52000 0x500>;
+				interrupts = <47>;
+				clocks = <&gateclk 20>;
+				status = "disabled";
+			};
+
+			xor@60900 {
+				compatible = "marvell,orion-xor";
+				reg = <0x60900 0x100
+				       0x60b00 0x100>;
+				clocks = <&gateclk 22>;
+				status = "okay";
+
+				xor10 {
+					interrupts = <51>;
+					dmacap,memcpy;
+					dmacap,xor;
+				};
+				xor11 {
+					interrupts = <52>;
+					dmacap,memcpy;
+					dmacap,xor;
+					dmacap,memset;
+				};
+			};
+
+			ethernet@70000 {
+				compatible = "marvell,armada-xp-neta";
+			};
+
+			ethernet@74000 {
+				compatible = "marvell,armada-xp-neta";
+			};
+
+			xor@f0900 {
+				compatible = "marvell,orion-xor";
+				reg = <0xF0900 0x100
+				       0xF0B00 0x100>;
+				clocks = <&gateclk 28>;
+				status = "okay";
+
+				xor00 {
+					interrupts = <94>;
+					dmacap,memcpy;
+					dmacap,xor;
+				};
+				xor01 {
+					interrupts = <95>;
+					dmacap,memcpy;
+					dmacap,xor;
+					dmacap,memset;
+				};
+			};
+		};
+	};
+
+	clocks {
+		/* 25 MHz reference crystal */
+		refclk: oscillator {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <25000000>;
+		};
+	};
+};
+
+&pinctrl {
+	ge0_gmii_pins: ge0-gmii-pins {
+		marvell,pins =
+		     "mpp0",  "mpp1",  "mpp2",  "mpp3",
+		     "mpp4",  "mpp5",  "mpp6",  "mpp7",
+		     "mpp8",  "mpp9",  "mpp10", "mpp11",
+		     "mpp12", "mpp13", "mpp14", "mpp15",
+		     "mpp16", "mpp17", "mpp18", "mpp19",
+		     "mpp20", "mpp21", "mpp22", "mpp23";
+		marvell,function = "ge0";
+	};
+
+	ge0_rgmii_pins: ge0-rgmii-pins {
+		marvell,pins =
+		     "mpp0", "mpp1", "mpp2", "mpp3",
+		     "mpp4", "mpp5", "mpp6", "mpp7",
+		     "mpp8", "mpp9", "mpp10", "mpp11";
+		marvell,function = "ge0";
+	};
+
+	ge1_rgmii_pins: ge1-rgmii-pins {
+		marvell,pins =
+		     "mpp12", "mpp13", "mpp14", "mpp15",
+		     "mpp16", "mpp17", "mpp18", "mpp19",
+		     "mpp20", "mpp21", "mpp22", "mpp23";
+		marvell,function = "ge1";
+	};
+
+	sdio_pins: sdio-pins {
+		marvell,pins = "mpp30", "mpp31", "mpp32",
+			       "mpp33", "mpp34", "mpp35";
+		marvell,function = "sd0";
+	};
+
+	spi0_pins: spi0-pins {
+		marvell,pins = "mpp36", "mpp37",
+			       "mpp38", "mpp39";
+		marvell,function = "spi0";
+	};
+
+	uart2_pins: uart2-pins {
+		marvell,pins = "mpp42", "mpp43";
+		marvell,function = "uart2";
+	};
+
+	uart3_pins: uart3-pins {
+		marvell,pins = "mpp44", "mpp45";
+		marvell,function = "uart3";
+	};
+};

arch/arm/dts/axp209.dtsi

@@ -89,4 +89,9 @@
 			regulator-name = "ldo5";
 		};
 	};
+
+	usb_power_supply: usb_power_supply {
+		compatible = "x-powers,axp202-usb-power-supply";
+		status = "disabled";
+	};
 };

arch/arm/dts/dra7-evm.dts

@@ -0,0 +1,693 @@
+/*
+ * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "dra74x.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "TI DRA742";
+	compatible = "ti,dra7-evm", "ti,dra742", "ti,dra74", "ti,dra7";
+
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x60000000>; /* 1536 MB */
+	};
+
+	mmc2_3v3: fixedregulator-mmc2 {
+		compatible = "regulator-fixed";
+		regulator-name = "mmc2_3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	extcon_usb1: extcon_usb1 {
+		compatible = "linux,extcon-usb-gpio";
+		id-gpio = <&pcf_gpio_21 1 GPIO_ACTIVE_HIGH>;
+	};
+
+	extcon_usb2: extcon_usb2 {
+		compatible = "linux,extcon-usb-gpio";
+		id-gpio = <&pcf_gpio_21 2 GPIO_ACTIVE_HIGH>;
+	};
+
+	vtt_fixed: fixedregulator-vtt {
+		compatible = "regulator-fixed";
+		regulator-name = "vtt_fixed";
+		regulator-min-microvolt = <1350000>;
+		regulator-max-microvolt = <1350000>;
+		regulator-always-on;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&gpio7 11 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&dra7_pmx_core {
+	pinctrl-names = "default";
+	pinctrl-0 = <&vtt_pin>;
+
+	vtt_pin: pinmux_vtt_pin {
+		pinctrl-single,pins = <
+			0x3b4 (PIN_OUTPUT | MUX_MODE14) /* spi1_cs1.gpio7_11 */
+		>;
+	};
+
+	i2c1_pins: pinmux_i2c1_pins {
+		pinctrl-single,pins = <
+			0x400 (PIN_INPUT | MUX_MODE0) /* i2c1_sda */
+			0x404 (PIN_INPUT | MUX_MODE0) /* i2c1_scl */
+		>;
+	};
+
+	i2c2_pins: pinmux_i2c2_pins {
+		pinctrl-single,pins = <
+			0x408 (PIN_INPUT | MUX_MODE0) /* i2c2_sda */
+			0x40c (PIN_INPUT | MUX_MODE0) /* i2c2_scl */
+		>;
+	};
+
+	i2c3_pins: pinmux_i2c3_pins {
+		pinctrl-single,pins = <
+			0x288 (PIN_INPUT | MUX_MODE9) /* gpio6_14.i2c3_sda */
+			0x28c (PIN_INPUT | MUX_MODE9) /* gpio6_15.i2c3_scl */
+		>;
+	};
+
+	mcspi1_pins: pinmux_mcspi1_pins {
+		pinctrl-single,pins = <
+			0x3a4 (PIN_INPUT | MUX_MODE0) /* spi1_sclk */
+			0x3a8 (PIN_INPUT | MUX_MODE0) /* spi1_d1 */
+			0x3ac (PIN_INPUT | MUX_MODE0) /* spi1_d0 */
+			0x3b0 (PIN_INPUT_SLEW | MUX_MODE0) /* spi1_cs0 */
+			0x3b8 (PIN_INPUT_SLEW | MUX_MODE6) /* spi1_cs2.hdmi1_hpd */
+			0x3bc (PIN_INPUT_SLEW | MUX_MODE6) /* spi1_cs3.hdmi1_cec */
+		>;
+	};
+
+	mcspi2_pins: pinmux_mcspi2_pins {
+		pinctrl-single,pins = <
+			0x3c0 (PIN_INPUT | MUX_MODE0) /* spi2_sclk */
+			0x3c4 (PIN_INPUT_SLEW | MUX_MODE0) /* spi2_d1 */
+			0x3c8 (PIN_INPUT_SLEW | MUX_MODE0) /* spi2_d1 */
+			0x3cc (PIN_INPUT_SLEW | MUX_MODE0) /* spi2_cs0 */
+		>;
+	};
+
+	uart1_pins: pinmux_uart1_pins {
+		pinctrl-single,pins = <
+			0x3e0 (PIN_INPUT_SLEW | MUX_MODE0) /* uart1_rxd */
+			0x3e4 (PIN_INPUT_SLEW | MUX_MODE0) /* uart1_txd */
+			0x3e8 (PIN_INPUT | MUX_MODE3) /* uart1_ctsn */
+			0x3ec (PIN_INPUT | MUX_MODE3) /* uart1_rtsn */
+		>;
+	};
+
+	uart2_pins: pinmux_uart2_pins {
+		pinctrl-single,pins = <
+			0x3f0 (PIN_INPUT | MUX_MODE0) /* uart2_rxd */
+			0x3f4 (PIN_INPUT | MUX_MODE0) /* uart2_txd */
+			0x3f8 (PIN_INPUT | MUX_MODE0) /* uart2_ctsn */
+			0x3fc (PIN_INPUT | MUX_MODE0) /* uart2_rtsn */
+		>;
+	};
+
+	uart3_pins: pinmux_uart3_pins {
+		pinctrl-single,pins = <
+			0x248 (PIN_INPUT_SLEW | MUX_MODE0) /* uart3_rxd */
+			0x24c (PIN_INPUT_SLEW | MUX_MODE0) /* uart3_txd */
+		>;
+	};
+
+	qspi1_pins: pinmux_qspi1_pins {
+		pinctrl-single,pins = <
+			0x4c (PIN_INPUT | MUX_MODE1)  /* gpmc_a3.qspi1_cs2 */
+			0x50 (PIN_INPUT | MUX_MODE1)  /* gpmc_a4.qspi1_cs3 */
+			0x74 (PIN_INPUT | MUX_MODE1)  /* gpmc_a13.qspi1_rtclk */
+			0x78 (PIN_INPUT | MUX_MODE1)  /* gpmc_a14.qspi1_d3 */
+			0x7c (PIN_INPUT | MUX_MODE1)  /* gpmc_a15.qspi1_d2 */
+			0x80 (PIN_INPUT | MUX_MODE1) /* gpmc_a16.qspi1_d1 */
+			0x84 (PIN_INPUT | MUX_MODE1)  /* gpmc_a17.qspi1_d0 */
+			0x88 (PIN_INPUT | MUX_MODE1)  /* qpmc_a18.qspi1_sclk */
+			0xb8 (PIN_INPUT_PULLUP | MUX_MODE1)  /* gpmc_cs2.qspi1_cs0 */
+			0xbc (PIN_INPUT_PULLUP | MUX_MODE1)  /* gpmc_cs3.qspi1_cs1 */
+		>;
+	};
+
+	usb1_pins: pinmux_usb1_pins {
+                pinctrl-single,pins = <
+			0x280 (PIN_INPUT_SLEW | MUX_MODE0) /* usb1_drvvbus */
+                >;
+        };
+
+	usb2_pins: pinmux_usb2_pins {
+                pinctrl-single,pins = <
+			0x284 (PIN_INPUT_SLEW | MUX_MODE0) /* usb2_drvvbus */
+                >;
+        };
+
+	nand_flash_x16: nand_flash_x16 {
+		/* On DRA7 EVM, GPMC_WPN and NAND_BOOTn comes from DIP switch
+		 * So NAND flash requires following switch settings:
+		 * SW5.9 (GPMC_WPN) = LOW
+		 * SW5.1 (NAND_BOOTn) = HIGH */
+		pinctrl-single,pins = <
+			0x0 	(PIN_INPUT  | MUX_MODE0)	/* gpmc_ad0	*/
+			0x4 	(PIN_INPUT  | MUX_MODE0)	/* gpmc_ad1	*/
+			0x8 	(PIN_INPUT  | MUX_MODE0)	/* gpmc_ad2	*/
+			0xc 	(PIN_INPUT  | MUX_MODE0)	/* gpmc_ad3	*/
+			0x10	(PIN_INPUT  | MUX_MODE0)	/* gpmc_ad4	*/
+			0x14	(PIN_INPUT  | MUX_MODE0)	/* gpmc_ad5	*/
+			0x18	(PIN_INPUT  | MUX_MODE0)	/* gpmc_ad6	*/
+			0x1c	(PIN_INPUT  | MUX_MODE0)	/* gpmc_ad7	*/
+			0x20	(PIN_INPUT  | MUX_MODE0)	/* gpmc_ad8	*/
+			0x24	(PIN_INPUT  | MUX_MODE0)	/* gpmc_ad9	*/
+			0x28	(PIN_INPUT  | MUX_MODE0)	/* gpmc_ad10	*/
+			0x2c	(PIN_INPUT  | MUX_MODE0)	/* gpmc_ad11	*/
+			0x30	(PIN_INPUT  | MUX_MODE0)	/* gpmc_ad12	*/
+			0x34	(PIN_INPUT  | MUX_MODE0)	/* gpmc_ad13	*/
+			0x38	(PIN_INPUT  | MUX_MODE0)	/* gpmc_ad14	*/
+			0x3c	(PIN_INPUT  | MUX_MODE0)	/* gpmc_ad15	*/
+			0xd8	(PIN_INPUT_PULLUP  | MUX_MODE0)	/* gpmc_wait0	*/
+			0xcc	(PIN_OUTPUT | MUX_MODE0)	/* gpmc_wen	*/
+			0xb4	(PIN_OUTPUT_PULLUP | MUX_MODE0)	/* gpmc_csn0	*/
+			0xc4	(PIN_OUTPUT | MUX_MODE0)	/* gpmc_advn_ale */
+			0xc8	(PIN_OUTPUT | MUX_MODE0)	/* gpmc_oen_ren	 */
+			0xd0	(PIN_OUTPUT | MUX_MODE0)	/* gpmc_be0n_cle */
+		>;
+	};
+
+	cpsw_default: cpsw_default {
+		pinctrl-single,pins = <
+			/* Slave 1 */
+			0x250 (PIN_OUTPUT | MUX_MODE0)	/* rgmii0_txc.rgmii0_txc */
+			0x254 (PIN_OUTPUT | MUX_MODE0)	/* rgmii0_txctl.rgmii0_txctl */
+			0x258 (PIN_OUTPUT | MUX_MODE0)	/* rgmii0_td3.rgmii0_txd3 */
+			0x25c (PIN_OUTPUT | MUX_MODE0)	/* rgmii0_txd2.rgmii0_txd2 */
+			0x260 (PIN_OUTPUT | MUX_MODE0)	/* rgmii0_txd1.rgmii0_txd1 */
+			0x264 (PIN_OUTPUT | MUX_MODE0)	/* rgmii0_txd0.rgmii0_txd0 */
+			0x268 (PIN_INPUT | MUX_MODE0)	/* rgmii0_rxc.rgmii0_rxc */
+			0x26c (PIN_INPUT | MUX_MODE0)	/* rgmii0_rxctl.rgmii0_rxctl */
+			0x270 (PIN_INPUT | MUX_MODE0)	/* rgmii0_rxd3.rgmii0_rxd3 */
+			0x274 (PIN_INPUT | MUX_MODE0)	/* rgmii0_rxd2.rgmii0_rxd2 */
+			0x278 (PIN_INPUT | MUX_MODE0)	/* rgmii0_rxd1.rgmii0_rxd1 */
+			0x27c (PIN_INPUT | MUX_MODE0)	/* rgmii0_rxd0.rgmii0_rxd0 */
+
+			/* Slave 2 */
+			0x198 (PIN_OUTPUT | MUX_MODE3)	/* vin2a_d12.rgmii1_txc */
+			0x19c (PIN_OUTPUT | MUX_MODE3)	/* vin2a_d13.rgmii1_tctl */
+			0x1a0 (PIN_OUTPUT | MUX_MODE3)	/* vin2a_d14.rgmii1_td3 */
+			0x1a4 (PIN_OUTPUT | MUX_MODE3)	/* vin2a_d15.rgmii1_td2 */
+			0x1a8 (PIN_OUTPUT | MUX_MODE3)	/* vin2a_d16.rgmii1_td1 */
+			0x1ac (PIN_OUTPUT | MUX_MODE3)	/* vin2a_d17.rgmii1_td0 */
+			0x1b0 (PIN_INPUT | MUX_MODE3)	/* vin2a_d18.rgmii1_rclk */
+			0x1b4 (PIN_INPUT | MUX_MODE3)	/* vin2a_d19.rgmii1_rctl */
+			0x1b8 (PIN_INPUT | MUX_MODE3)	/* vin2a_d20.rgmii1_rd3 */
+			0x1bc (PIN_INPUT | MUX_MODE3)	/* vin2a_d21.rgmii1_rd2 */
+			0x1c0 (PIN_INPUT | MUX_MODE3)	/* vin2a_d22.rgmii1_rd1 */
+			0x1c4 (PIN_INPUT | MUX_MODE3)	/* vin2a_d23.rgmii1_rd0 */
+		>;
+
+	};
+
+	cpsw_sleep: cpsw_sleep {
+		pinctrl-single,pins = <
+			/* Slave 1 */
+			0x250 (MUX_MODE15)
+			0x254 (MUX_MODE15)
+			0x258 (MUX_MODE15)
+			0x25c (MUX_MODE15)
+			0x260 (MUX_MODE15)
+			0x264 (MUX_MODE15)
+			0x268 (MUX_MODE15)
+			0x26c (MUX_MODE15)
+			0x270 (MUX_MODE15)
+			0x274 (MUX_MODE15)
+			0x278 (MUX_MODE15)
+			0x27c (MUX_MODE15)
+
+			/* Slave 2 */
+			0x198 (MUX_MODE15)
+			0x19c (MUX_MODE15)
+			0x1a0 (MUX_MODE15)
+			0x1a4 (MUX_MODE15)
+			0x1a8 (MUX_MODE15)
+			0x1ac (MUX_MODE15)
+			0x1b0 (MUX_MODE15)
+			0x1b4 (MUX_MODE15)
+			0x1b8 (MUX_MODE15)
+			0x1bc (MUX_MODE15)
+			0x1c0 (MUX_MODE15)
+			0x1c4 (MUX_MODE15)
+		>;
+	};
+
+	davinci_mdio_default: davinci_mdio_default {
+		pinctrl-single,pins = <
+			0x23c (PIN_OUTPUT_PULLUP | MUX_MODE0)	/* mdio_d.mdio_d */
+			0x240 (PIN_INPUT_PULLUP | MUX_MODE0)	/* mdio_clk.mdio_clk */
+		>;
+	};
+
+	davinci_mdio_sleep: davinci_mdio_sleep {
+		pinctrl-single,pins = <
+			0x23c (MUX_MODE15)
+			0x240 (MUX_MODE15)
+		>;
+	};
+
+	dcan1_pins_default: dcan1_pins_default {
+		pinctrl-single,pins = <
+			0x3d0   (PIN_OUTPUT_PULLUP | MUX_MODE0) /* dcan1_tx */
+			0x418   (PULL_UP | MUX_MODE1) /* wakeup0.dcan1_rx */
+		>;
+	};
+
+	dcan1_pins_sleep: dcan1_pins_sleep {
+		pinctrl-single,pins = <
+			0x3d0   (MUX_MODE15 | PULL_UP)	/* dcan1_tx.off */
+			0x418   (MUX_MODE15 | PULL_UP)	/* wakeup0.off */
+		>;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <400000>;
+
+	tps659038: tps659038@58 {
+		compatible = "ti,tps659038";
+		reg = <0x58>;
+
+		tps659038_pmic {
+			compatible = "ti,tps659038-pmic";
+
+			regulators {
+				smps123_reg: smps123 {
+					/* VDD_MPU */
+					regulator-name = "smps123";
+					regulator-min-microvolt = < 850000>;
+					regulator-max-microvolt = <1250000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				smps45_reg: smps45 {
+					/* VDD_DSPEVE */
+					regulator-name = "smps45";
+					regulator-min-microvolt = < 850000>;
+					regulator-max-microvolt = <1150000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				smps6_reg: smps6 {
+					/* VDD_GPU - over VDD_SMPS6 */
+					regulator-name = "smps6";
+					regulator-min-microvolt = <850000>;
+					regulator-max-microvolt = <1250000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				smps7_reg: smps7 {
+					/* CORE_VDD */
+					regulator-name = "smps7";
+					regulator-min-microvolt = <850000>;
+					regulator-max-microvolt = <1060000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				smps8_reg: smps8 {
+					/* VDD_IVAHD */
+					regulator-name = "smps8";
+					regulator-min-microvolt = < 850000>;
+					regulator-max-microvolt = <1250000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				smps9_reg: smps9 {
+					/* VDDS1V8 */
+					regulator-name = "smps9";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				ldo1_reg: ldo1 {
+					/* LDO1_OUT --> SDIO  */
+					regulator-name = "ldo1";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-boot-on;
+				};
+
+				ldo2_reg: ldo2 {
+					/* VDD_RTCIO */
+					/* LDO2 -> VDDSHV5, LDO2 also goes to CAN_PHY_3V3 */
+					regulator-name = "ldo2";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				ldo3_reg: ldo3 {
+					/* VDDA_1V8_PHY */
+					regulator-name = "ldo3";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				ldo9_reg: ldo9 {
+					/* VDD_RTC */
+					regulator-name = "ldo9";
+					regulator-min-microvolt = <1050000>;
+					regulator-max-microvolt = <1050000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				ldoln_reg: ldoln {
+					/* VDDA_1V8_PLL */
+					regulator-name = "ldoln";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				ldousb_reg: ldousb {
+					/* VDDA_3V_USB: VDDA_USBHS33 */
+					regulator-name = "ldousb";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-boot-on;
+				};
+			};
+		};
+	};
+
+	pcf_gpio_21: gpio@21 {
+		compatible = "ti,pcf8575";
+		reg = <0x21>;
+		lines-initial-states = <0x1408>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&gpio6>;
+		interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+};
+
+&i2c2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins>;
+	clock-frequency = <400000>;
+};
+
+&i2c3 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c3_pins>;
+	clock-frequency = <400000>;
+};
+
+&mcspi1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcspi1_pins>;
+};
+
+&mcspi2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcspi2_pins>;
+};
+
+&uart1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	interrupts-extended = <&crossbar_mpu GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>,
+			      <&dra7_pmx_core 0x3e0>;
+};
+
+&uart2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
+};
+
+&uart3 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>;
+};
+
+&mmc1 {
+	status = "okay";
+	vmmc-supply = <&ldo1_reg>;
+	bus-width = <4>;
+};
+
+&mmc2 {
+	status = "okay";
+	vmmc-supply = <&mmc2_3v3>;
+	bus-width = <8>;
+};
+
+&cpu0 {
+	cpu0-supply = <&smps123_reg>;
+};
+
+&qspi {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&qspi1_pins>;
+
+	spi-max-frequency = <48000000>;
+	m25p80@0 {
+		compatible = "s25fl256s1";
+		spi-max-frequency = <48000000>;
+		reg = <0>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>;
+		spi-cpol;
+		spi-cpha;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		/* MTD partition table.
+		 * The ROM checks the first four physical blocks
+		 * for a valid file to boot and the flash here is
+		 * 64KiB block size.
+		 */
+		partition@0 {
+			label = "QSPI.SPL";
+			reg = <0x00000000 0x000010000>;
+		};
+		partition@1 {
+			label = "QSPI.SPL.backup1";
+			reg = <0x00010000 0x00010000>;
+		};
+		partition@2 {
+			label = "QSPI.SPL.backup2";
+			reg = <0x00020000 0x00010000>;
+		};
+		partition@3 {
+			label = "QSPI.SPL.backup3";
+			reg = <0x00030000 0x00010000>;
+		};
+		partition@4 {
+			label = "QSPI.u-boot";
+			reg = <0x00040000 0x00100000>;
+		};
+		partition@5 {
+			label = "QSPI.u-boot-spl-os";
+			reg = <0x00140000 0x00080000>;
+		};
+		partition@6 {
+			label = "QSPI.u-boot-env";
+			reg = <0x001c0000 0x00010000>;
+		};
+		partition@7 {
+			label = "QSPI.u-boot-env.backup1";
+			reg = <0x001d0000 0x0010000>;
+		};
+		partition@8 {
+			label = "QSPI.kernel";
+			reg = <0x001e0000 0x0800000>;
+		};
+		partition@9 {
+			label = "QSPI.file-system";
+			reg = <0x009e0000 0x01620000>;
+		};
+	};
+};
+
+&omap_dwc3_1 {
+	extcon = <&extcon_usb1>;
+};
+
+&omap_dwc3_2 {
+	extcon = <&extcon_usb2>;
+};
+
+&usb1 {
+	dr_mode = "peripheral";
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb1_pins>;
+};
+
+&usb2 {
+	dr_mode = "host";
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb2_pins>;
+};
+
+&elm {
+	status = "okay";
+};
+
+&gpmc {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&nand_flash_x16>;
+	ranges = <0 0 0 0x01000000>;	/* minimum GPMC partition = 16MB */
+	nand@0,0 {
+		reg = <0 0 4>;		/* device IO registers */
+		ti,nand-ecc-opt = "bch8";
+		ti,elm-id = <&elm>;
+		nand-bus-width = <16>;
+		gpmc,device-width = <2>;
+		gpmc,sync-clk-ps = <0>;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <80>;
+		gpmc,cs-wr-off-ns = <80>;
+		gpmc,adv-on-ns = <0>;
+		gpmc,adv-rd-off-ns = <60>;
+		gpmc,adv-wr-off-ns = <60>;
+		gpmc,we-on-ns = <10>;
+		gpmc,we-off-ns = <50>;
+		gpmc,oe-on-ns = <4>;
+		gpmc,oe-off-ns = <40>;
+		gpmc,access-ns = <40>;
+		gpmc,wr-access-ns = <80>;
+		gpmc,rd-cycle-ns = <80>;
+		gpmc,wr-cycle-ns = <80>;
+		gpmc,bus-turnaround-ns = <0>;
+		gpmc,cycle2cycle-delay-ns = <0>;
+		gpmc,clk-activation-ns = <0>;
+		gpmc,wait-monitoring-ns = <0>;
+		gpmc,wr-data-mux-bus-ns = <0>;
+		/* MTD partition table */
+		/* All SPL-* partitions are sized to minimal length
+		 * which can be independently programmable. For
+		 * NAND flash this is equal to size of erase-block */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		partition@0 {
+			label = "NAND.SPL";
+			reg = <0x00000000 0x000020000>;
+		};
+		partition@1 {
+			label = "NAND.SPL.backup1";
+			reg = <0x00020000 0x00020000>;
+		};
+		partition@2 {
+			label = "NAND.SPL.backup2";
+			reg = <0x00040000 0x00020000>;
+		};
+		partition@3 {
+			label = "NAND.SPL.backup3";
+			reg = <0x00060000 0x00020000>;
+		};
+		partition@4 {
+			label = "NAND.u-boot-spl-os";
+			reg = <0x00080000 0x00040000>;
+		};
+		partition@5 {
+			label = "NAND.u-boot";
+			reg = <0x000c0000 0x00100000>;
+		};
+		partition@6 {
+			label = "NAND.u-boot-env";
+			reg = <0x001c0000 0x00020000>;
+		};
+		partition@7 {
+			label = "NAND.u-boot-env.backup1";
+			reg = <0x001e0000 0x00020000>;
+		};
+		partition@8 {
+			label = "NAND.kernel";
+			reg = <0x00200000 0x00800000>;
+		};
+		partition@9 {
+			label = "NAND.file-system";
+			reg = <0x00a00000 0x0f600000>;
+		};
+	};
+};
+
+&usb2_phy1 {
+	phy-supply = <&ldousb_reg>;
+};
+
+&usb2_phy2 {
+	phy-supply = <&ldousb_reg>;
+};
+
+&gpio7 {
+	ti,no-reset-on-init;
+	ti,no-idle-on-init;
+};
+
+&mac {
+	status = "okay";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&cpsw_default>;
+	pinctrl-1 = <&cpsw_sleep>;
+	dual_emac;
+};
+
+&cpsw_emac0 {
+	phy_id = <&davinci_mdio>, <2>;
+	phy-mode = "rgmii";
+	dual_emac_res_vlan = <1>;
+};
+
+&cpsw_emac1 {
+	phy_id = <&davinci_mdio>, <3>;
+	phy-mode = "rgmii";
+	dual_emac_res_vlan = <2>;
+};
+
+&davinci_mdio {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&davinci_mdio_default>;
+	pinctrl-1 = <&davinci_mdio_sleep>;
+};
+
+&dcan1 {
+	status = "ok";
+	pinctrl-names = "default", "sleep", "active";
+	pinctrl-0 = <&dcan1_pins_sleep>;
+	pinctrl-1 = <&dcan1_pins_sleep>;
+	pinctrl-2 = <&dcan1_pins_default>;
+};

arch/arm/dts/dra74x.dtsi

@@ -0,0 +1,90 @@
+/*
+ * Copyright (C) 2014 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ * Based on "omap4.dtsi"
+ */
+
+#include "dra7.dtsi"
+
+/ {
+	compatible = "ti,dra742", "ti,dra74", "ti,dra7";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a15";
+			reg = <0>;
+
+			operating-points = <
+				/* kHz    uV */
+				1000000	1060000
+				1176000	1160000
+				>;
+
+			clocks = <&dpll_mpu_ck>;
+			clock-names = "cpu";
+
+			clock-latency = <300000>; /* From omap-cpufreq driver */
+
+			/* cooling options */
+			cooling-min-level = <0>;
+			cooling-max-level = <2>;
+			#cooling-cells = <2>; /* min followed by max */
+		};
+		cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a15";
+			reg = <1>;
+		};
+	};
+
+	pmu {
+		compatible = "arm,cortex-a15-pmu";
+		interrupt-parent = <&wakeupgen>;
+		interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	ocp {
+		omap_dwc3_4: omap_dwc3_4@48940000 {
+			compatible = "ti,dwc3";
+			ti,hwmods = "usb_otg_ss4";
+			reg = <0x48940000 0x10000>;
+			interrupts = <GIC_SPI 346 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			utmi-mode = <2>;
+			ranges;
+			status = "disabled";
+			usb4: usb@48950000 {
+				compatible = "snps,dwc3";
+				reg = <0x48950000 0x17000>;
+				interrupts = <GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>;
+				tx-fifo-resize;
+				maximum-speed = "high-speed";
+				dr_mode = "otg";
+			};
+		};
+	};
+};
+
+&dss {
+	reg = <0x58000000 0x80>,
+	      <0x58004054 0x4>,
+	      <0x58004300 0x20>,
+	      <0x58005054 0x4>,
+	      <0x58005300 0x20>;
+	reg-names = "dss", "pll1_clkctrl", "pll1",
+		    "pll2_clkctrl", "pll2";
+
+	clocks = <&dss_dss_clk>,
+		 <&dss_video1_clk>,
+		 <&dss_video2_clk>;
+	clock-names = "fck", "video1_clk", "video2_clk";
+};

arch/arm/dts/exynos5422-odroidxu3.dts

@@ -31,6 +31,18 @@
 			0xb0000000 0xea00000>;
 	};
 
+	adc@12D10000 {
+		u-boot,dm-pre-reloc;
+		status = "okay";
+	};
+
+	i2c@12CA0000 {
+		s2mps11_pmic@66 {
+			compatible = "samsung,s2mps11-pmic";
+			reg = <0x66>;
+		};
+	};
+
 	ehci@12110000 {
 		samsung,vbus-gpio = <&gpx2 6 GPIO_ACTIVE_HIGH>;
 	};

arch/arm/dts/exynos54xx.dtsi

@@ -42,6 +42,13 @@
 		xhci1 = "/xhci@12400000";
 	};
 
+	adc@12D10000 {
+		compatible = "samsung,exynos-adc-v2";
+		reg = <0x12D10000 0x100>;
+		interrupts = <0 106 0>;
+		status = "disabled";
+	};
+
 	i2c@12CA0000 {
 		#address-cells = <1>;
 		#size-cells = <0>;

arch/arm/dts/exynos5800-peach-pi.dts

@@ -12,6 +12,7 @@
 
 / {
 	model = "Samsung/Google Peach Pi board based on Exynos5800";
+	cpu-model = "Exynos5800";
 
 	compatible = "google,pit-rev#", "google,pit",
 		"google,peach", "samsung,exynos5800", "samsung,exynos5";

arch/arm/dts/k2e-clocks.dtsi

@@ -0,0 +1,77 @@
+/*
+ * Copyright 2014 Texas Instruments, Inc.
+ *
+ * Keystone 2 Edison SoC specific device tree
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+clocks {
+	mainpllclk: mainpllclk@2310110 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,main-pll-clock";
+		clocks = <&refclksys>;
+		reg = <0x02620350 4>, <0x02310110 4>, <0x02310108 4>;
+		reg-names = "control", "multiplier", "post-divider";
+	};
+
+	papllclk: papllclk@2620358 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,pll-clock";
+		clocks = <&refclkpass>;
+		clock-output-names = "papllclk";
+		reg = <0x02620358 4>;
+		reg-names = "control";
+	};
+
+	ddr3apllclk: ddr3apllclk@2620360 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,pll-clock";
+		clocks = <&refclkddr3a>;
+		clock-output-names = "ddr-3a-pll-clk";
+		reg = <0x02620360 4>;
+		reg-names = "control";
+	};
+
+	clkusb1: clkusb1 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk16>;
+		clock-output-names = "usb1";
+		reg = <0x02350004 0xb00>, <0x02350000 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <0>;
+	};
+
+	clkhyperlink0: clkhyperlink0 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk12>;
+		clock-output-names = "hyperlink-0";
+		reg = <0x02350030 0xb00>, <0x02350014 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <5>;
+	};
+
+	clkpcie1: clkpcie1 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk12>;
+		clock-output-names = "pcie1";
+		reg = <0x0235006c 0xb00>, <0x02350048 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <18>;
+	};
+
+	clkxge: clkxge {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk13>;
+		clock-output-names = "xge";
+		reg = <0x023500c8 0xb00>, <0x02350074 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <29>;
+	};
+};

arch/arm/dts/k2e-evm.dts

@@ -0,0 +1,154 @@
+/*
+ * Copyright 2013-2014 Texas Instruments, Inc.
+ *
+ * Keystone 2 Edison EVM device tree
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "keystone.dtsi"
+#include "k2e.dtsi"
+
+/ {
+	compatible =  "ti,k2e-evm","ti,keystone";
+	model = "Texas Instruments Keystone 2 Edison EVM";
+
+	soc {
+
+		clocks {
+			refclksys: refclksys {
+				#clock-cells = <0>;
+				compatible = "fixed-clock";
+				clock-frequency = <100000000>;
+				clock-output-names = "refclk-sys";
+			};
+
+			refclkpass: refclkpass {
+				#clock-cells = <0>;
+				compatible = "fixed-clock";
+				clock-frequency = <100000000>;
+				clock-output-names = "refclk-pass";
+			};
+
+			refclkddr3a: refclkddr3a {
+				#clock-cells = <0>;
+				compatible = "fixed-clock";
+				clock-frequency = <100000000>;
+				clock-output-names = "refclk-ddr3a";
+			};
+		};
+	};
+};
+
+&usb_phy {
+	status = "okay";
+};
+
+&usb {
+	status = "okay";
+};
+
+&usb1_phy {
+	status = "okay";
+};
+
+&usb1 {
+	status = "okay";
+};
+
+&i2c0 {
+	dtt@50 {
+		compatible = "at,24c1024";
+		reg = <0x50>;
+	};
+};
+
+&aemif {
+	cs0 {
+		#address-cells = <2>;
+		#size-cells = <1>;
+		clock-ranges;
+		ranges;
+
+		ti,cs-chipselect = <0>;
+		/* all timings in nanoseconds */
+		ti,cs-min-turnaround-ns = <12>;
+		ti,cs-read-hold-ns = <6>;
+		ti,cs-read-strobe-ns = <23>;
+		ti,cs-read-setup-ns = <9>;
+		ti,cs-write-hold-ns = <8>;
+		ti,cs-write-strobe-ns = <23>;
+		ti,cs-write-setup-ns = <8>;
+
+		nand@0,0 {
+			compatible = "ti,keystone-nand","ti,davinci-nand";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0 0 0x4000000
+			       1 0 0x0000100>;
+
+			ti,davinci-chipselect = <0>;
+			ti,davinci-mask-ale = <0x2000>;
+			ti,davinci-mask-cle = <0x4000>;
+			ti,davinci-mask-chipsel = <0>;
+			nand-ecc-mode = "hw";
+			ti,davinci-ecc-bits = <4>;
+			nand-on-flash-bbt;
+
+			partition@0 {
+				label = "u-boot";
+				reg = <0x0 0x100000>;
+				read-only;
+			};
+
+			partition@100000 {
+				label = "params";
+				reg = <0x100000 0x80000>;
+				read-only;
+			};
+
+			partition@180000 {
+				label = "ubifs";
+				reg = <0x180000 0x1FE80000>;
+			};
+		};
+	};
+};
+
+&spi0 {
+	nor_flash: n25q128a11@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "Micron,n25q128a11";
+		spi-max-frequency = <54000000>;
+		m25p,fast-read;
+		reg = <0>;
+
+		partition@0 {
+			label = "u-boot-spl";
+			reg = <0x0 0x80000>;
+			read-only;
+		};
+
+		partition@1 {
+			label = "misc";
+			reg = <0x80000 0xf80000>;
+		};
+	};
+};
+
+&mdio {
+	status = "ok";
+	ethphy0: ethernet-phy@0 {
+		compatible = "marvell,88E1514", "marvell,88E1510", "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+
+	ethphy1: ethernet-phy@1 {
+		compatible = "marvell,88E1514", "marvell,88E1510", "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};

arch/arm/dts/k2e-netcp.dtsi

@@ -0,0 +1,206 @@
+/*
+ * Device Tree Source for Keystone 2 Edison Netcp driver
+ *
+ * Copyright 2015 Texas Instruments, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+qmss: qmss@2a40000 {
+	compatible = "ti,keystone-navigator-qmss";
+	dma-coherent;
+	#address-cells = <1>;
+	#size-cells = <1>;
+	clocks = <&chipclk13>;
+	ranges;
+	queue-range	= <0 0x2000>;
+	linkram0	= <0x100000 0x4000>;
+	linkram1	= <0 0x10000>;
+
+	qmgrs {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		qmgr0 {
+			managed-queues = <0 0x2000>;
+			reg = <0x2a40000 0x20000>,
+			      <0x2a06000 0x400>,
+			      <0x2a02000 0x1000>,
+			      <0x2a03000 0x1000>,
+			      <0x23a80000 0x20000>,
+			      <0x2a80000 0x20000>;
+			reg-names = "peek", "status", "config",
+				    "region", "push", "pop";
+		};
+	};
+	queue-pools {
+		qpend {
+			qpend-0 {
+				qrange = <658 8>;
+				interrupts =<0 40 0xf04 0 41 0xf04 0 42 0xf04
+					     0 43 0xf04 0 44 0xf04 0 45 0xf04
+					     0 46 0xf04 0 47 0xf04>;
+			};
+			qpend-1 {
+				qrange = <528 16>;
+				interrupts = <0 48 0xf04 0 49 0xf04 0 50 0xf04
+					      0 51 0xf04 0 52 0xf04 0 53 0xf04
+					      0 54 0xf04 0 55 0xf04 0 56 0xf04
+					      0 57 0xf04 0 58 0xf04 0 59 0xf04
+					      0 60 0xf04 0 61 0xf04 0 62 0xf04
+					      0 63 0xf04>;
+				qalloc-by-id;
+			};
+			qpend-2 {
+				qrange = <544 16>;
+				interrupts = <0 64 0xf04 0 65 0xf04 0 66 0xf04
+					      0 59 0xf04 0 68 0xf04 0 69 0xf04
+					      0 70 0xf04 0 71 0xf04 0 72 0xf04
+					      0 73 0xf04 0 74 0xf04 0 75 0xf04
+					      0 76 0xf04 0 77 0xf04 0 78 0xf04
+					      0 79 0xf04>;
+			};
+		};
+		general-purpose {
+			gp-0 {
+				qrange = <4000 64>;
+			};
+			netcp-tx {
+				qrange = <896 128>;
+				qalloc-by-id;
+			};
+		};
+	};
+	descriptor-regions {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		region-12 {
+			id = <12>;
+			region-spec = <8192 128>;	/* num_desc desc_size */
+			link-index = <0x4000>;
+		};
+	};
+}; /* qmss */
+
+knav_dmas: knav_dmas@0 {
+	compatible = "ti,keystone-navigator-dma";
+	clocks = <&papllclk>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+	ranges;
+	ti,navigator-cloud-address = <0x23a80000 0x23a90000
+				 0x23a80000 0x23a90000>;
+
+	dma_gbe: dma_gbe@0 {
+		reg = <0x24186000 0x100>,
+			  <0x24187000 0x2a0>,
+			  <0x24188000 0xb60>,
+			  <0x24186100 0x80>,
+			  <0x24189000 0x1000>;
+		reg-names = "global", "txchan", "rxchan",
+				"txsched", "rxflow";
+	};
+};
+
+netcp: netcp@24000000 {
+	reg = <0x2620110 0x8>;
+	reg-names = "efuse";
+	compatible = "ti,netcp-1.0";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	/* NetCP address range */
+	ranges = <0 0x24000000 0x1000000>;
+
+	clocks = <&papllclk>, <&clkcpgmac>, <&chipclk12>;
+	dma-coherent;
+
+	ti,navigator-dmas = <&dma_gbe 0>,
+			<&dma_gbe 8>,
+			<&dma_gbe 0>;
+	ti,navigator-dma-names = "netrx0", "netrx1", "nettx";
+
+	netcp-devices {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		gbe@200000 { /* ETHSS */
+			label = "netcp-gbe";
+			compatible = "ti,netcp-gbe-9";
+			reg = <0x200000 0x900>, <0x220000 0x20000>;
+			/* enable-ale; */
+			tx-queue = <896>;
+			tx-channel = "nettx";
+
+			interfaces {
+				gbe0: interface-0 {
+					slave-port = <0>;
+					link-interface	= <1>;
+					phy-handle	= <&ethphy0>;
+				};
+				gbe1: interface-1 {
+					slave-port = <1>;
+					link-interface	= <1>;
+					phy-handle	= <&ethphy1>;
+				};
+			};
+
+			secondary-slave-ports {
+				port-2 {
+					slave-port = <2>;
+					link-interface	= <2>;
+				};
+				port-3 {
+					slave-port = <3>;
+					link-interface	= <2>;
+				};
+				port-4 {
+					slave-port = <4>;
+					link-interface	= <2>;
+				};
+				port-5 {
+					slave-port = <5>;
+					link-interface	= <2>;
+				};
+				port-6 {
+					slave-port = <6>;
+					link-interface	= <2>;
+				};
+				port-7 {
+					slave-port = <7>;
+					link-interface	= <2>;
+				};
+			};
+		};
+	};
+
+	netcp-interfaces {
+		interface-0 {
+			rx-channel = "netrx0";
+			rx-pool = <1024 12>;
+			tx-pool = <1024 12>;
+			rx-queue-depth = <128 128 0 0>;
+			rx-buffer-size = <1518 4096 0 0>;
+			rx-queue = <528>;
+			tx-completion-queue = <530>;
+			efuse-mac = <1>;
+			netcp-gbe = <&gbe0>;
+
+		};
+		interface-1 {
+			rx-channel = "netrx1";
+			rx-pool = <1024 12>;
+			tx-pool = <1024 12>;
+			rx-queue-depth = <128 128 0 0>;
+			rx-buffer-size = <1518 4096 0 0>;
+			rx-queue = <529>;
+			tx-completion-queue = <531>;
+			efuse-mac = <0>;
+			local-mac-address = [02 18 31 7e 3e 00];
+			netcp-gbe = <&gbe1>;
+		};
+	};
+};

arch/arm/dts/k2e.dtsi

@@ -0,0 +1,147 @@
+/*
+ * Copyright 2013-2014 Texas Instruments, Inc.
+ *
+ * Keystone 2 Edison soc device tree
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/ {
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		interrupt-parent = <&gic>;
+
+		cpu@0 {
+			compatible = "arm,cortex-a15";
+			device_type = "cpu";
+			reg = <0>;
+		};
+
+		cpu@1 {
+			compatible = "arm,cortex-a15";
+			device_type = "cpu";
+			reg = <1>;
+		};
+
+		cpu@2 {
+			compatible = "arm,cortex-a15";
+			device_type = "cpu";
+			reg = <2>;
+		};
+
+		cpu@3 {
+			compatible = "arm,cortex-a15";
+			device_type = "cpu";
+			reg = <3>;
+		};
+	};
+
+	soc {
+		/include/ "k2e-clocks.dtsi"
+
+		usb: usb@2680000 {
+			interrupts = <GIC_SPI 152 IRQ_TYPE_EDGE_RISING>;
+			dwc3@2690000 {
+				interrupts = <GIC_SPI 152 IRQ_TYPE_EDGE_RISING>;
+			};
+		};
+
+		usb1_phy: usb_phy@2620750 {
+			compatible = "ti,keystone-usbphy";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x2620750 24>;
+			status = "disabled";
+		};
+
+		usb1: usb@25000000 {
+			compatible = "ti,keystone-dwc3";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x25000000 0x10000>;
+			clocks = <&clkusb1>;
+			clock-names = "usb";
+			interrupts = <GIC_SPI 414 IRQ_TYPE_EDGE_RISING>;
+			ranges;
+			dma-coherent;
+			dma-ranges;
+			status = "disabled";
+
+			dwc3@25010000 {
+				compatible = "synopsys,dwc3";
+				reg = <0x25010000 0x70000>;
+				interrupts = <GIC_SPI 414 IRQ_TYPE_EDGE_RISING>;
+				usb-phy = <&usb1_phy>, <&usb1_phy>;
+			};
+		};
+
+		dspgpio0: keystone_dsp_gpio@02620240 {
+			compatible = "ti,keystone-dsp-gpio";
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio,syscon-dev = <&devctrl 0x240>;
+		};
+
+		pcie1: pcie@21020000 {
+			compatible = "ti,keystone-pcie","snps,dw-pcie";
+			clocks = <&clkpcie1>;
+			clock-names = "pcie";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			reg =  <0x21021000 0x2000>, <0x21020000 0x1000>, <0x02620128 4>;
+			ranges = <0x81000000 0 0 0x23260000 0x4000 0x4000
+				0x82000000 0 0x60000000 0x60000000 0 0x10000000>;
+
+			status = "disabled";
+			device_type = "pci";
+			num-lanes = <2>;
+
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 7>;
+			interrupt-map = <0 0 0 1 &pcie_intc1 0>, /* INT A */
+					<0 0 0 2 &pcie_intc1 1>, /* INT B */
+					<0 0 0 3 &pcie_intc1 2>, /* INT C */
+					<0 0 0 4 &pcie_intc1 3>; /* INT D */
+
+			pcie_msi_intc1: msi-interrupt-controller {
+				interrupt-controller;
+				#interrupt-cells = <1>;
+				interrupt-parent = <&gic>;
+				interrupts = <GIC_SPI 377 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 378 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 379 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 380 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 381 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 382 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 383 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 384 IRQ_TYPE_EDGE_RISING>;
+			};
+
+			pcie_intc1: legacy-interrupt-controller {
+				interrupt-controller;
+				#interrupt-cells = <1>;
+				interrupt-parent = <&gic>;
+				interrupts = <GIC_SPI 373 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 374 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 375 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 376 IRQ_TYPE_EDGE_RISING>;
+			};
+		};
+
+		mdio: mdio@24200f00 {
+			compatible	= "ti,keystone_mdio", "ti,davinci_mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x24200f00 0x100>;
+			status = "disabled";
+			clocks = <&clkcpgmac>;
+			clock-names = "fck";
+			bus_freq	= <2500000>;
+		};
+		/include/ "k2e-netcp.dtsi"
+	};
+};

arch/arm/dts/k2g-evm.dts

@@ -0,0 +1,21 @@
+/*
+ * Copyright 2014 Texas Instruments, Inc.
+ *
+ * Keystone 2 Galileo EVM device tree
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "k2g.dtsi"
+
+/ {
+	compatible =  "ti,k2g-evm","ti,keystone";
+	model = "Texas Instruments Keystone 2 Galileo EVM";
+
+	chosen {
+		stdout-path = &uart0;
+	};
+};

arch/arm/dts/k2g.dtsi

@@ -0,0 +1,72 @@
+/*
+ * Copyright 2014 Texas Instruments, Inc.
+ *
+ * Keystone 2 Galileo soc device tree
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include "skeleton.dtsi"
+
+/ {
+	model = "Texas Instruments Keystone 2 SoC";
+	#address-cells = <1>;
+	#size-cells = <1>;
+	interrupt-parent = <&gic>;
+
+	aliases {
+		serial0	= &uart0;
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x80000000>;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		interrupt-parent = <&gic>;
+
+		cpu@0 {
+			compatible = "arm,cortex-a15";
+			device_type = "cpu";
+			reg = <0>;
+		};
+	};
+
+	gic: interrupt-controller {
+		compatible = "arm,cortex-a15-gic";
+		#interrupt-cells = <3>;
+		interrupt-controller;
+		reg = <0x0 0x02561000 0x0 0x1000>,
+		      <0x0 0x02562000 0x0 0x2000>,
+		      <0x0 0x02564000 0x0 0x1000>,
+		      <0x0 0x02566000 0x0 0x2000>;
+		interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) |
+				IRQ_TYPE_LEVEL_HIGH)>;
+	};
+
+	soc {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "ti,keystone","simple-bus";
+		interrupt-parent = <&gic>;
+		ranges;
+
+		uart0: serial@02530c00 {
+			compatible = "ns16550a";
+			current-speed = <115200>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			reg = <0x02530c00 0x100>;
+			clock-names = "uart";
+			interrupts = <GIC_SPI 164 IRQ_TYPE_EDGE_RISING>;
+		};
+
+	};
+};

arch/arm/dts/k2hk-clocks.dtsi

@@ -0,0 +1,425 @@
+/*
+ * Copyright 2013-2014 Texas Instruments, Inc.
+ *
+ * Keystone 2 Kepler/Hawking SoC clock nodes
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+clocks {
+	armpllclk: armpllclk@2620370 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,pll-clock";
+		clocks = <&refclkarm>;
+		clock-output-names = "arm-pll-clk";
+		reg = <0x02620370 4>;
+		reg-names = "control";
+	};
+
+	mainpllclk: mainpllclk@2310110 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,main-pll-clock";
+		clocks = <&refclksys>;
+		reg = <0x02620350 4>, <0x02310110 4>, <0x02310108 4>;
+		reg-names = "control", "multiplier", "post-divider";
+	};
+
+	papllclk: papllclk@2620358 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,pll-clock";
+		clocks = <&refclkpass>;
+		clock-output-names = "papllclk";
+		reg = <0x02620358 4>;
+		reg-names = "control";
+	};
+
+	ddr3apllclk: ddr3apllclk@2620360 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,pll-clock";
+		clocks = <&refclkddr3a>;
+		clock-output-names = "ddr-3a-pll-clk";
+		reg = <0x02620360 4>;
+		reg-names = "control";
+	};
+
+	ddr3bpllclk: ddr3bpllclk@2620368 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,pll-clock";
+		clocks = <&refclkddr3b>;
+		clock-output-names = "ddr-3b-pll-clk";
+		reg = <0x02620368 4>;
+		reg-names = "control";
+	};
+
+	clktsip: clktsip {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk16>;
+		clock-output-names = "tsip";
+		reg = <0x02350000 0xb00>, <0x02350000 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <0>;
+	};
+
+	clksrio: clksrio {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk1rstiso13>;
+		clock-output-names = "srio";
+		reg = <0x0235002c 0xb00>, <0x02350010 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <4>;
+	};
+
+	clkhyperlink0: clkhyperlink0 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk12>;
+		clock-output-names = "hyperlink-0";
+		reg = <0x02350030 0xb00>, <0x02350014 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <5>;
+	};
+
+	clkgem1: clkgem1 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk1>;
+		clock-output-names = "gem1";
+		reg = <0x02350040 0xb00>, <0x02350024 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <9>;
+	};
+
+	clkgem2: clkgem2 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk1>;
+		clock-output-names = "gem2";
+		reg = <0x02350044 0xb00>, <0x02350028 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <10>;
+	};
+
+	clkgem3: clkgem3 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk1>;
+		clock-output-names = "gem3";
+		reg = <0x02350048 0xb00>, <0x0235002c 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <11>;
+	};
+
+	clkgem4: clkgem4 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk1>;
+		clock-output-names = "gem4";
+		reg = <0x0235004c 0xb00>, <0x02350030 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <12>;
+	};
+
+	clkgem5: clkgem5 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk1>;
+		clock-output-names = "gem5";
+		reg = <0x02350050 0xb00>, <0x02350034 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <13>;
+	};
+
+	clkgem6: clkgem6 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk1>;
+		clock-output-names = "gem6";
+		reg = <0x02350054 0xb00>, <0x02350038 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <14>;
+	};
+
+	clkgem7: clkgem7 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk1>;
+		clock-output-names = "gem7";
+		reg = <0x02350058 0xb00>, <0x0235003c 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <15>;
+	};
+
+	clkddr31: clkddr31 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk13>;
+		clock-output-names = "ddr3-1";
+		reg = <0x02350060 0xb00>, <0x02350040 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <16>;
+	};
+
+	clktac: clktac {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk13>;
+		clock-output-names = "tac";
+		reg = <0x02350064 0xb00>, <0x02350044 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <17>;
+	};
+
+	clkrac01: clkrac01 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk13>;
+		clock-output-names = "rac-01";
+		reg = <0x02350068 0xb00>, <0x02350044 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <17>;
+	};
+
+	clkrac23: clkrac23 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk13>;
+		clock-output-names = "rac-23";
+		reg = <0x0235006c 0xb00>, <0x02350048 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <18>;
+	};
+
+	clkfftc0: clkfftc0 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk13>;
+		clock-output-names = "fftc-0";
+		reg = <0x02350070 0xb00>, <0x0235004c 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <19>;
+	};
+
+	clkfftc1: clkfftc1 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk13>;
+		clock-output-names = "fftc-1";
+		reg = <0x02350074 0xb00>, <0x0235004c 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <19>;
+	};
+
+	clkfftc2: clkfftc2 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk13>;
+		clock-output-names = "fftc-2";
+		reg = <0x02350078 0xb00>, <0x02350050 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <20>;
+	};
+
+	clkfftc3: clkfftc3 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk13>;
+		clock-output-names = "fftc-3";
+		reg = <0x0235007c 0xb00>, <0x02350050 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <20>;
+	};
+
+	clkfftc4: clkfftc4 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk13>;
+		clock-output-names = "fftc-4";
+		reg = <0x02350080 0xb00>, <0x02350050 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <20>;
+	};
+
+	clkfftc5: clkfftc5 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk13>;
+		clock-output-names = "fftc-5";
+		reg = <0x02350084 0xb00>, <0x02350050 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <20>;
+	};
+
+	clkaif: clkaif {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk13>;
+		clock-output-names = "aif";
+		reg = <0x02350088 0xb00>, <0x02350054 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <21>;
+	};
+
+	clktcp3d0: clktcp3d0 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk13>;
+		clock-output-names = "tcp3d-0";
+		reg = <0x0235008c 0xb00>, <0x02350058 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <22>;
+	};
+
+	clktcp3d1: clktcp3d1 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk13>;
+		clock-output-names = "tcp3d-1";
+		reg = <0x02350090 0xb00>, <0x02350058 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <22>;
+	};
+
+	clktcp3d2: clktcp3d2 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk13>;
+		clock-output-names = "tcp3d-2";
+		reg = <0x02350094 0xb00>, <0x0235005c 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <23>;
+	};
+
+	clktcp3d3: clktcp3d3 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk13>;
+		clock-output-names = "tcp3d-3";
+		reg = <0x02350098 0xb00>, <0x0235005c 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <23>;
+	};
+
+	clkvcp0: clkvcp0 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk13>;
+		clock-output-names = "vcp-0";
+		reg = <0x0235009c 0xb00>, <0x02350060 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <24>;
+	};
+
+	clkvcp1: clkvcp1 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk13>;
+		clock-output-names = "vcp-1";
+		reg = <0x023500a0 0xb00>, <0x02350060 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <24>;
+	};
+
+	clkvcp2: clkvcp2 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk13>;
+		clock-output-names = "vcp-2";
+		reg = <0x023500a4 0xb00>, <0x02350060 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <24>;
+	};
+
+	clkvcp3: clkvcp3 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk13>;
+		clock-output-names = "vcp-3";
+		reg = <0x023500a8 0xb00>, <0x02350060 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <24>;
+	};
+
+	clkvcp4: clkvcp4 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk13>;
+		clock-output-names = "vcp-4";
+		reg = <0x023500ac 0xb00>, <0x02350064 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <25>;
+	};
+
+	clkvcp5: clkvcp5 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk13>;
+		clock-output-names = "vcp-5";
+		reg = <0x023500b0 0xb00>, <0x02350064 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <25>;
+	};
+
+	clkvcp6: clkvcp6 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk13>;
+		clock-output-names = "vcp-6";
+		reg = <0x023500b4 0xb00>, <0x02350064 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <25>;
+	};
+
+	clkvcp7: clkvcp7 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk13>;
+		clock-output-names = "vcp-7";
+		reg = <0x023500b8 0xb00>, <0x02350064 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <25>;
+	};
+
+	clkbcp: clkbcp {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk13>;
+		clock-output-names = "bcp";
+		reg = <0x023500bc 0xb00>, <0x02350068 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <26>;
+	};
+
+	clkdxb: clkdxb {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk13>;
+		clock-output-names = "dxb";
+		reg = <0x023500c0 0xb00>, <0x0235006c 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <27>;
+	};
+
+	clkhyperlink1: clkhyperlink1 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk12>;
+		clock-output-names = "hyperlink-1";
+		reg = <0x023500c4 0xb00>, <0x02350070 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <28>;
+	};
+
+	clkxge: clkxge {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk13>;
+		clock-output-names = "xge";
+		reg = <0x023500c8 0xb00>, <0x02350074 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <29>;
+	};
+};

arch/arm/dts/k2hk-evm.dts

@@ -0,0 +1,182 @@
+/*
+ * Copyright 2013-2014 Texas Instruments, Inc.
+ *
+ * Keystone 2 Kepler/Hawking EVM device tree
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "keystone.dtsi"
+#include "k2hk.dtsi"
+
+/ {
+	compatible =  "ti,k2hk-evm","ti,keystone";
+	model = "Texas Instruments Keystone 2 Kepler/Hawking EVM";
+
+	soc {
+		clocks {
+			refclksys: refclksys {
+				#clock-cells = <0>;
+				compatible = "fixed-clock";
+				clock-frequency = <122880000>;
+				clock-output-names = "refclk-sys";
+			};
+
+			refclkpass: refclkpass {
+				#clock-cells = <0>;
+				compatible = "fixed-clock";
+				clock-frequency = <122880000>;
+				clock-output-names = "refclk-pass";
+			};
+
+			refclkarm: refclkarm {
+				#clock-cells = <0>;
+				compatible = "fixed-clock";
+				clock-frequency = <125000000>;
+				clock-output-names = "refclk-arm";
+			};
+
+			refclkddr3a: refclkddr3a {
+				#clock-cells = <0>;
+				compatible = "fixed-clock";
+				clock-frequency = <100000000>;
+				clock-output-names = "refclk-ddr3a";
+			};
+
+			refclkddr3b: refclkddr3b {
+				#clock-cells = <0>;
+				compatible = "fixed-clock";
+				clock-frequency = <100000000>;
+				clock-output-names = "refclk-ddr3b";
+			};
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		debug1_1 {
+			label = "keystone:green:debug1";
+			gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; /* 12 */
+		};
+
+		debug1_2 {
+			label = "keystone:red:debug1";
+			gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>; /* 13 */
+		};
+
+		debug2 {
+			label = "keystone:blue:debug2";
+			gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>; /* 14 */
+		};
+
+		debug3 {
+			label = "keystone:blue:debug3";
+			gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>; /* 15 */
+		};
+	};
+};
+
+&usb_phy {
+	status = "okay";
+};
+
+&usb {
+	status = "okay";
+};
+
+&aemif {
+	cs0 {
+		#address-cells = <2>;
+		#size-cells = <1>;
+		clock-ranges;
+		ranges;
+
+		ti,cs-chipselect = <0>;
+		/* all timings in nanoseconds */
+		ti,cs-min-turnaround-ns = <12>;
+		ti,cs-read-hold-ns = <6>;
+		ti,cs-read-strobe-ns = <23>;
+		ti,cs-read-setup-ns = <9>;
+		ti,cs-write-hold-ns = <8>;
+		ti,cs-write-strobe-ns = <23>;
+		ti,cs-write-setup-ns = <8>;
+
+		nand@0,0 {
+			compatible = "ti,keystone-nand","ti,davinci-nand";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0 0 0x4000000
+			       1 0 0x0000100>;
+
+			ti,davinci-chipselect = <0>;
+			ti,davinci-mask-ale = <0x2000>;
+			ti,davinci-mask-cle = <0x4000>;
+			ti,davinci-mask-chipsel = <0>;
+			nand-ecc-mode = "hw";
+			ti,davinci-ecc-bits = <4>;
+			nand-on-flash-bbt;
+
+			partition@0 {
+				label = "u-boot";
+				reg = <0x0 0x100000>;
+				read-only;
+			};
+
+			partition@100000 {
+				label = "params";
+				reg = <0x100000 0x80000>;
+				read-only;
+			};
+
+			partition@180000 {
+				label = "ubifs";
+				reg = <0x180000 0x1fe80000>;
+			};
+		};
+	};
+};
+
+&i2c0 {
+	dtt@50 {
+		compatible = "at,24c1024";
+		reg = <0x50>;
+	};
+};
+
+&spi0 {
+	nor_flash: n25q128a11@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "Micron,n25q128a11";
+		spi-max-frequency = <54000000>;
+		m25p,fast-read;
+		reg = <0>;
+
+		partition@0 {
+			label = "u-boot-spl";
+			reg = <0x0 0x80000>;
+			read-only;
+		};
+
+		partition@1 {
+			label = "misc";
+			reg = <0x80000 0xf80000>;
+		};
+	};
+};
+
+&mdio {
+	status = "ok";
+	ethphy0: ethernet-phy@0 {
+		compatible = "marvell,88E1111", "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+
+	ethphy1: ethernet-phy@1 {
+		compatible = "marvell,88E1111", "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};

arch/arm/dts/k2hk-netcp.dtsi

@@ -0,0 +1,208 @@
+/*
+ * Device Tree Source for Keystone 2 Hawking Netcp driver
+ *
+ * Copyright 2015 Texas Instruments, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+qmss: qmss@2a40000 {
+	compatible = "ti,keystone-navigator-qmss";
+	dma-coherent;
+	#address-cells = <1>;
+	#size-cells = <1>;
+	clocks = <&chipclk13>;
+	ranges;
+	queue-range	= <0 0x4000>;
+	linkram0	= <0x100000 0x8000>;
+	linkram1	= <0x0 0x10000>;
+
+	qmgrs {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		qmgr0 {
+			managed-queues = <0 0x2000>;
+			reg = <0x2a40000 0x20000>,
+			      <0x2a06000 0x400>,
+			      <0x2a02000 0x1000>,
+			      <0x2a03000 0x1000>,
+			      <0x23a80000 0x20000>,
+			      <0x2a80000 0x20000>;
+			reg-names = "peek", "status", "config",
+				    "region", "push", "pop";
+		};
+
+		qmgr1 {
+			managed-queues = <0x2000 0x2000>;
+			reg = <0x2a60000 0x20000>,
+			      <0x2a06400 0x400>,
+			      <0x2a04000 0x1000>,
+			      <0x2a05000 0x1000>,
+			      <0x23aa0000 0x20000>,
+			      <0x2aa0000 0x20000>;
+			reg-names = "peek", "status", "config",
+				    "region", "push", "pop";
+		};
+	};
+	queue-pools {
+		qpend {
+			qpend-0 {
+				qrange = <658 8>;
+				interrupts =<0 40 0xf04 0 41 0xf04 0 42 0xf04
+					     0 43 0xf04 0 44 0xf04 0 45 0xf04
+					     0 46 0xf04 0 47 0xf04>;
+			};
+			qpend-1 {
+				qrange = <8704 16>;
+				interrupts = <0 48 0xf04 0 49 0xf04 0 50 0xf04
+					      0 51 0xf04 0 52 0xf04 0 53 0xf04
+					      0 54 0xf04 0 55 0xf04 0 56 0xf04
+					      0 57 0xf04 0 58 0xf04 0 59 0xf04
+					      0 60 0xf04 0 61 0xf04 0 62 0xf04
+					      0 63 0xf04>;
+				qalloc-by-id;
+			};
+			qpend-2 {
+				qrange = <8720 16>;
+				interrupts = <0 64 0xf04 0 65 0xf04 0 66 0xf04
+					      0 59 0xf04 0 68 0xf04 0 69 0xf04
+					      0 70 0xf04 0 71 0xf04 0 72 0xf04
+					      0 73 0xf04 0 74 0xf04 0 75 0xf04
+					      0 76 0xf04 0 77 0xf04 0 78 0xf04
+					      0 79 0xf04>;
+			};
+		};
+		general-purpose {
+			gp-0 {
+				qrange = <4000 64>;
+			};
+			netcp-tx {
+				qrange = <640 9>;
+				qalloc-by-id;
+			};
+			netcpx-tx {
+				qrange = <8752 8>;
+				qalloc-by-id;
+			};
+		};
+	};
+	descriptor-regions {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		region-12 {
+			id = <12>;
+			region-spec = <8192 128>;	/* num_desc desc_size */
+			link-index = <0x4000>;
+		};
+	};
+}; /* qmss */
+
+knav_dmas: knav_dmas@0 {
+	compatible = "ti,keystone-navigator-dma";
+	clocks = <&papllclk>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+	ranges;
+	ti,navigator-cloud-address = <0x23a80000 0x23a90000
+				   0x23aa0000 0x23ab0000>;
+
+	dma_gbe: dma_gbe@0 {
+		reg = <0x2004000 0x100>,
+			  <0x2004400 0x120>,
+			  <0x2004800 0x300>,
+			  <0x2004c00 0x120>,
+			  <0x2005000 0x400>;
+		reg-names = "global", "txchan", "rxchan",
+				"txsched", "rxflow";
+	};
+};
+
+netcp: netcp@2000000 {
+	reg = <0x2620110 0x8>;
+	reg-names = "efuse";
+	compatible = "ti,netcp-1.0";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	/* NetCP address range */
+	ranges  = <0 0x2000000 0x100000>;
+
+	clocks = <&papllclk>, <&clkcpgmac>, <&chipclk12>;
+	dma-coherent;
+
+	ti,navigator-dmas = <&dma_gbe 22>,
+			<&dma_gbe 23>,
+			<&dma_gbe 8>;
+	ti,navigator-dma-names = "netrx0", "netrx1", "nettx";
+
+	netcp-devices {
+		ranges;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		gbe@90000 { /* ETHSS */
+			#address-cells = <1>;
+			#size-cells = <1>;
+			label = "netcp-gbe";
+			compatible = "ti,netcp-gbe";
+			reg = <0x90000 0x300>, <0x90400 0x400>, <0x90800 0x700>;
+			/* enable-ale; */
+			tx-queue = <648>;
+			tx-channel = "nettx";
+
+			interfaces {
+				gbe0: interface-0 {
+					slave-port = <0>;
+					link-interface = <1>;
+					phy-handle = <&ethphy0>;
+				};
+				gbe1: interface-1 {
+					slave-port = <1>;
+					link-interface = <1>;
+					phy-handle = <&ethphy1>;
+				};
+			};
+
+			secondary-slave-ports {
+				port-2 {
+					slave-port = <2>;
+					link-interface	= <2>;
+				};
+				port-3 {
+					slave-port = <3>;
+					link-interface	= <2>;
+				};
+			};
+		};
+	};
+
+	netcp-interfaces {
+		interface-0 {
+			rx-channel = "netrx0";
+			rx-pool = <1024 12>;
+			tx-pool = <1024 12>;
+			rx-queue-depth = <128 128 0 0>;
+			rx-buffer-size = <1518 4096 0 0>;
+			rx-queue = <8704>;
+			tx-completion-queue = <8706>;
+			efuse-mac = <1>;
+			netcp-gbe = <&gbe0>;
+
+		};
+		interface-1 {
+			rx-channel = "netrx1";
+			rx-pool = <1024 12>;
+			tx-pool = <1024 12>;
+			rx-queue-depth = <128 128 0 0>;
+			rx-buffer-size = <1518 4096 0 0>;
+			rx-queue = <8705>;
+			tx-completion-queue = <8707>;
+			efuse-mac = <0>;
+			local-mac-address = [02 18 31 7e 3e 6f];
+			netcp-gbe = <&gbe1>;
+		};
+	};
+};

arch/arm/dts/k2hk.dtsi

@@ -0,0 +1,114 @@
+/*
+ * Copyright 2013-2014 Texas Instruments, Inc.
+ *
+ * Keystone 2 Kepler/Hawking soc specific device tree
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/ {
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		interrupt-parent = <&gic>;
+
+		cpu@0 {
+			compatible = "arm,cortex-a15";
+			device_type = "cpu";
+			reg = <0>;
+		};
+
+		cpu@1 {
+			compatible = "arm,cortex-a15";
+			device_type = "cpu";
+			reg = <1>;
+		};
+
+		cpu@2 {
+			compatible = "arm,cortex-a15";
+			device_type = "cpu";
+			reg = <2>;
+		};
+
+		cpu@3 {
+			compatible = "arm,cortex-a15";
+			device_type = "cpu";
+			reg = <3>;
+		};
+	};
+
+	soc {
+		/include/ "k2hk-clocks.dtsi"
+
+		dspgpio0: keystone_dsp_gpio@02620240 {
+			compatible = "ti,keystone-dsp-gpio";
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio,syscon-dev = <&devctrl 0x240>;
+		};
+
+		dspgpio1: keystone_dsp_gpio@2620244 {
+			compatible = "ti,keystone-dsp-gpio";
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio,syscon-dev = <&devctrl 0x244>;
+		};
+
+		dspgpio2: keystone_dsp_gpio@2620248 {
+			compatible = "ti,keystone-dsp-gpio";
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio,syscon-dev = <&devctrl 0x248>;
+		};
+
+		dspgpio3: keystone_dsp_gpio@262024c {
+			compatible = "ti,keystone-dsp-gpio";
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio,syscon-dev = <&devctrl 0x24c>;
+		};
+
+		dspgpio4: keystone_dsp_gpio@2620250 {
+			compatible = "ti,keystone-dsp-gpio";
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio,syscon-dev = <&devctrl 0x250>;
+		};
+
+		dspgpio5: keystone_dsp_gpio@2620254 {
+			compatible = "ti,keystone-dsp-gpio";
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio,syscon-dev = <&devctrl 0x254>;
+		};
+
+		dspgpio6: keystone_dsp_gpio@2620258 {
+			compatible = "ti,keystone-dsp-gpio";
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio,syscon-dev = <&devctrl 0x258>;
+		};
+
+		dspgpio7: keystone_dsp_gpio@262025c {
+			compatible = "ti,keystone-dsp-gpio";
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio,syscon-dev = <&devctrl 0x25c>;
+		};
+
+		mdio: mdio@02090300 {
+			compatible	= "ti,keystone_mdio", "ti,davinci_mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x02090300 0x100>;
+			status = "disabled";
+			clocks = <&clkcpgmac>;
+			clock-names = "fck";
+			bus_freq	= <2500000>;
+		};
+		/include/ "k2hk-netcp.dtsi"
+	};
+};

arch/arm/dts/k2l-clocks.dtsi

@@ -0,0 +1,266 @@
+/*
+ * Copyright 2013-2014 Texas Instruments, Inc.
+ *
+ * Keystone 2 lamarr SoC clock nodes
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+clocks {
+	armpllclk: armpllclk@2620370 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,pll-clock";
+		clocks = <&refclksys>;
+		clock-output-names = "arm-pll-clk";
+		reg = <0x02620370 4>;
+		reg-names = "control";
+	};
+
+	mainpllclk: mainpllclk@2310110 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,main-pll-clock";
+		clocks = <&refclksys>;
+		reg = <0x02620350 4>, <0x02310110 4>, <0x02310108 4>;
+		reg-names = "control", "multiplier", "post-divider";
+	};
+
+	papllclk: papllclk@2620358 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,pll-clock";
+		clocks = <&refclksys>;
+		clock-output-names = "papllclk";
+		reg = <0x02620358 4>;
+		reg-names = "control";
+	};
+
+	ddr3apllclk: ddr3apllclk@2620360 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,pll-clock";
+		clocks = <&refclksys>;
+		clock-output-names = "ddr-3a-pll-clk";
+		reg = <0x02620360 4>;
+		reg-names = "control";
+	};
+
+	clkdfeiqnsys: clkdfeiqnsys {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk12>;
+		clock-output-names = "dfe";
+		reg-names = "control", "domain";
+		reg = <0x02350004 0xb00>, <0x02350000 0x400>;
+		domain-id = <0>;
+	};
+
+	clkpcie1: clkpcie1 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk12>;
+		clock-output-names = "pcie";
+		reg = <0x0235002c 0xb00>, <0x02350000 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <4>;
+	};
+
+	clkgem1: clkgem1 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk1>;
+		clock-output-names = "gem1";
+		reg = <0x02350040 0xb00>, <0x02350024 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <9>;
+	};
+
+	clkgem2: clkgem2 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk1>;
+		clock-output-names = "gem2";
+		reg = <0x02350044 0xb00>, <0x02350028 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <10>;
+	};
+
+	clkgem3: clkgem3 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk1>;
+		clock-output-names = "gem3";
+		reg = <0x02350048 0xb00>, <0x0235002c 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <11>;
+	};
+
+	clktac: clktac {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk13>;
+		clock-output-names = "tac";
+		reg = <0x02350064 0xb00>, <0x02350044 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <17>;
+	};
+
+	clkrac: clkrac {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk13>;
+		clock-output-names = "rac";
+		reg = <0x02350068 0xb00>, <0x02350044 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <17>;
+	};
+
+	clkdfepd0: clkdfepd0 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk13>;
+		clock-output-names = "dfe-pd0";
+		reg = <0x0235006c 0xb00>, <0x02350044 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <18>;
+	};
+
+	clkfftc0: clkfftc0 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk13>;
+		clock-output-names = "fftc-0";
+		reg = <0x02350070 0xb00>, <0x0235004c 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <19>;
+	};
+
+	clkosr: clkosr {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk13>;
+		clock-output-names = "osr";
+		reg = <0x02350088 0xb00>, <0x0235004c 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <21>;
+	};
+
+	clktcp3d0: clktcp3d0 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk13>;
+		clock-output-names = "tcp3d-0";
+		reg = <0x0235008c 0xb00>, <0x02350058 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <22>;
+	};
+
+	clktcp3d1: clktcp3d1 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk13>;
+		clock-output-names = "tcp3d-1";
+		reg = <0x02350094 0xb00>, <0x02350058 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <23>;
+	};
+
+	clkvcp0: clkvcp0 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk13>;
+		clock-output-names = "vcp-0";
+		reg = <0x0235009c 0xb00>, <0x02350060 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <24>;
+	};
+
+	clkvcp1: clkvcp1 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk13>;
+		clock-output-names = "vcp-1";
+		reg = <0x023500a0 0xb00>, <0x02350060 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <24>;
+	};
+
+	clkvcp2: clkvcp2 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk13>;
+		clock-output-names = "vcp-2";
+		reg = <0x023500a4 0xb00>, <0x02350060 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <24>;
+	};
+
+	clkvcp3: clkvcp3 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk13>;
+		clock-output-names = "vcp-3";
+		reg = <0x023500a8 0xb00>, <0x02350060 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <24>;
+	};
+
+	clkbcp: clkbcp {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk13>;
+		clock-output-names = "bcp";
+		reg = <0x023500bc 0xb00>, <0x02350068 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <26>;
+	};
+
+	clkdfepd1: clkdfepd1 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk13>;
+		clock-output-names = "dfe-pd1";
+		reg = <0x023500c0 0xb00>, <0x02350044 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <27>;
+	};
+
+	clkfftc1: clkfftc1 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk13>;
+		clock-output-names = "fftc-1";
+		reg = <0x023500c4 0xb00>, <0x023504c0 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <28>;
+	};
+
+	clkiqnail: clkiqnail {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk13>;
+		clock-output-names = "iqn-ail";
+		reg = <0x023500c8 0xb00>, <0x0235004c 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <29>;
+	};
+
+	clkuart2: clkuart2 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&clkmodrst0>;
+		clock-output-names = "uart2";
+		reg = <0x02350000 0xb00>, <0x02350000 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <0>;
+	};
+
+	clkuart3: clkuart3 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&clkmodrst0>;
+		clock-output-names = "uart3";
+		reg = <0x02350000 0xb00>, <0x02350000 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <0>;
+	};
+};

arch/arm/dts/k2l-evm.dts

@@ -0,0 +1,131 @@
+/*
+ * Copyright 2014 Texas Instruments, Inc.
+ *
+ * Keystone 2 Lamarr EVM device tree
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "keystone.dtsi"
+#include "k2l.dtsi"
+
+/ {
+	compatible =  "ti,k2l-evm","ti,keystone";
+	model = "Texas Instruments Keystone 2 Lamarr EVM";
+
+	soc {
+		clocks {
+			refclksys: refclksys {
+				#clock-cells = <0>;
+				compatible = "fixed-clock";
+				clock-frequency = <122880000>;
+				clock-output-names = "refclk-sys";
+			};
+		};
+	};
+};
+
+&usb_phy {
+	status = "okay";
+};
+
+&usb {
+	status = "okay";
+};
+
+&i2c0 {
+	dtt@50 {
+		compatible = "at,24c1024";
+		reg = <0x50>;
+	};
+};
+
+&aemif {
+	cs0 {
+		#address-cells = <2>;
+		#size-cells = <1>;
+		clock-ranges;
+		ranges;
+
+		ti,cs-chipselect = <0>;
+		/* all timings in nanoseconds */
+		ti,cs-min-turnaround-ns = <12>;
+		ti,cs-read-hold-ns = <6>;
+		ti,cs-read-strobe-ns = <23>;
+		ti,cs-read-setup-ns = <9>;
+		ti,cs-write-hold-ns = <8>;
+		ti,cs-write-strobe-ns = <23>;
+		ti,cs-write-setup-ns = <8>;
+
+		nand@0,0 {
+			compatible = "ti,keystone-nand","ti,davinci-nand";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0 0 0x4000000
+			       1 0 0x0000100>;
+
+			ti,davinci-chipselect = <0>;
+			ti,davinci-mask-ale = <0x2000>;
+			ti,davinci-mask-cle = <0x4000>;
+			ti,davinci-mask-chipsel = <0>;
+			nand-ecc-mode = "hw";
+			ti,davinci-ecc-bits = <4>;
+			nand-on-flash-bbt;
+
+			partition@0 {
+				label = "u-boot";
+				reg = <0x0 0x100000>;
+				read-only;
+			};
+
+			partition@100000 {
+				label = "params";
+				reg = <0x100000 0x80000>;
+				read-only;
+			};
+
+			partition@180000 {
+				label = "ubifs";
+				reg = <0x180000 0x7FE80000>;
+			};
+		};
+	};
+};
+
+&spi0 {
+	nor_flash: n25q128a11@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "Micron,n25q128a11";
+		spi-max-frequency = <54000000>;
+		m25p,fast-read;
+		reg = <0>;
+
+		partition@0 {
+			label = "u-boot-spl";
+			reg = <0x0 0x80000>;
+			read-only;
+		};
+
+		partition@1 {
+			label = "misc";
+			reg = <0x80000 0xf80000>;
+		};
+	};
+};
+
+&mdio {
+	status = "ok";
+	ethphy0: ethernet-phy@0 {
+		compatible = "marvell,88E1514", "marvell,88E1510", "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+
+	ethphy1: ethernet-phy@1 {
+		compatible = "marvell,88E1514", "marvell,88E1510", "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};

arch/arm/dts/k2l-netcp.dtsi

@@ -0,0 +1,189 @@
+/*
+ * Device Tree Source for Keystone 2 Lamarr Netcp driver
+ *
+ * Copyright 2015 Texas Instruments, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+qmss: qmss@2a40000 {
+	compatible = "ti,keystone-navigator-qmss";
+	dma-coherent;
+	#address-cells = <1>;
+	#size-cells = <1>;
+	clocks = <&chipclk13>;
+	ranges;
+	queue-range	= <0 0x2000>;
+	linkram0	= <0x100000 0x4000>;
+	linkram1	= <0x70000000 0x10000>; /* 1MB OSR mem */
+
+	qmgrs {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		qmgr0 {
+			managed-queues = <0 0x2000>;
+			reg = <0x2a40000 0x20000>,
+			      <0x2a06000 0x400>,
+			      <0x2a02000 0x1000>,
+			      <0x2a03000 0x1000>,
+			      <0x23a80000 0x20000>,
+			      <0x2a80000 0x20000>;
+			reg-names = "peek", "status", "config",
+				    "region", "push", "pop";
+		};
+	};
+	queue-pools {
+		qpend {
+			qpend-0 {
+				qrange = <658 8>;
+				interrupts =<0 40 0xf04 0 41 0xf04 0 42 0xf04
+					     0 43 0xf04 0 44 0xf04 0 45 0xf04
+					     0 46 0xf04 0 47 0xf04>;
+			};
+			qpend-1 {
+				qrange = <528 16>;
+				interrupts = <0 48 0xf04 0 49 0xf04 0 50 0xf04
+					      0 51 0xf04 0 52 0xf04 0 53 0xf04
+					      0 54 0xf04 0 55 0xf04 0 56 0xf04
+					      0 57 0xf04 0 58 0xf04 0 59 0xf04
+					      0 60 0xf04 0 61 0xf04 0 62 0xf04
+					      0 63 0xf04>;
+				qalloc-by-id;
+			};
+			qpend-2 {
+				qrange = <544 16>;
+				interrupts = <0 64 0xf04 0 65 0xf04 0 66 0xf04
+					      0 59 0xf04 0 68 0xf04 0 69 0xf04
+					      0 70 0xf04 0 71 0xf04 0 72 0xf04
+					      0 73 0xf04 0 74 0xf04 0 75 0xf04
+					      0 76 0xf04 0 77 0xf04 0 78 0xf04
+					      0 79 0xf04>;
+			};
+		};
+		general-purpose {
+			gp-0 {
+				qrange = <4000 64>;
+			};
+			netcp-tx {
+				qrange = <896 128>;
+				qalloc-by-id;
+			};
+		};
+	};
+	descriptor-regions {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		region-12 {
+			id = <12>;
+			region-spec = <8192 128>;	/* num_desc desc_size */
+			link-index = <0x4000>;
+		};
+	};
+}; /* qmss */
+
+knav_dmas: knav_dmas@0 {
+	compatible = "ti,keystone-navigator-dma";
+	clocks = <&papllclk>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+	ranges;
+	ti,navigator-cloud-address = <0x23a80000 0x23a90000>;
+
+	dma_gbe: dma_gbe@0 {
+		reg = <0x26186000 0x100>,
+			  <0x26187000 0x2a0>,
+			  <0x26188000 0xb60>,
+			  <0x26186100 0x80>,
+			  <0x26189000 0x1000>;
+		reg-names = "global", "txchan", "rxchan",
+				"txsched", "rxflow";
+	};
+};
+
+netcp: netcp@26000000 {
+	reg = <0x2620110 0x8>;
+	reg-names = "efuse";
+	compatible = "ti,netcp-1.0";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	/* NetCP address range */
+	ranges = <0 0x26000000 0x1000000>;
+
+	clocks = <&papllclk>, <&clkcpgmac>, <&chipclk12>;
+	dma-coherent;
+
+	ti,navigator-dmas = <&dma_gbe 0>,
+			<&dma_gbe 8>,
+			<&dma_gbe 0>;
+	ti,navigator-dma-names = "netrx0", "netrx1", "nettx";
+
+	netcp-devices {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		gbe@200000 { /* ETHSS */
+			label = "netcp-gbe";
+			compatible = "ti,netcp-gbe-5";
+			reg = <0x200000 0x900>, <0x220000 0x20000>;
+			/* enable-ale; */
+			tx-queue = <896>;
+			tx-channel = "nettx";
+
+			interfaces {
+				gbe0: interface-0 {
+					slave-port = <0>;
+					link-interface	= <1>;
+					phy-handle	= <&ethphy0>;
+				};
+				gbe1: interface-1 {
+					slave-port = <1>;
+					link-interface	= <1>;
+					phy-handle	= <&ethphy1>;
+				};
+			};
+
+			secondary-slave-ports {
+				port-2 {
+					slave-port = <2>;
+					link-interface	= <2>;
+				};
+				port-3 {
+					slave-port = <3>;
+					link-interface	= <2>;
+				};
+			};
+		};
+	};
+
+	netcp-interfaces {
+		interface-0 {
+			rx-channel = "netrx0";
+			rx-pool = <1024 12>;
+			tx-pool = <1024 12>;
+			rx-queue-depth = <128 128 0 0>;
+			rx-buffer-size = <1518 4096 0 0>;
+			rx-queue = <528>;
+			tx-completion-queue = <530>;
+			efuse-mac = <1>;
+			netcp-gbe = <&gbe0>;
+
+		};
+		interface-1 {
+			rx-channel = "netrx1";
+			rx-pool = <1024 12>;
+			tx-pool = <1024 12>;
+			rx-queue-depth = <128 128 0 0>;
+			rx-buffer-size = <1518 4096 0 0>;
+			rx-queue = <529>;
+			tx-completion-queue = <531>;
+			efuse-mac = <0>;
+			local-mac-address = [02 18 31 7e 3e 7f];
+			netcp-gbe = <&gbe1>;
+		};
+	};
+};

arch/arm/dts/k2l.dtsi

@@ -0,0 +1,108 @@
+/*
+ * Copyright 2014 Texas Instruments, Inc.
+ *
+ * Keystone 2 Lamarr SoC specific device tree
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/ {
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		interrupt-parent = <&gic>;
+
+		cpu@0 {
+			compatible = "arm,cortex-a15";
+			device_type = "cpu";
+			reg = <0>;
+		};
+
+		cpu@1 {
+			compatible = "arm,cortex-a15";
+			device_type = "cpu";
+			reg = <1>;
+		};
+	};
+
+	soc {
+		/include/ "k2l-clocks.dtsi"
+
+		uart2: serial@02348400 {
+			compatible = "ns16550a";
+			current-speed = <115200>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			reg = <0x02348400 0x100>;
+			clocks	= <&clkuart2>;
+			interrupts = <GIC_SPI 432 IRQ_TYPE_EDGE_RISING>;
+		};
+
+		uart3:	serial@02348800 {
+			compatible = "ns16550a";
+			current-speed = <115200>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			reg = <0x02348800 0x100>;
+			clocks	= <&clkuart3>;
+			interrupts = <GIC_SPI 435 IRQ_TYPE_EDGE_RISING>;
+		};
+
+		dspgpio0: keystone_dsp_gpio@02620240 {
+			compatible = "ti,keystone-dsp-gpio";
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio,syscon-dev = <&devctrl 0x240>;
+		};
+
+		dspgpio1: keystone_dsp_gpio@2620244 {
+			compatible = "ti,keystone-dsp-gpio";
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio,syscon-dev = <&devctrl 0x244>;
+		};
+
+		dspgpio2: keystone_dsp_gpio@2620248 {
+			compatible = "ti,keystone-dsp-gpio";
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio,syscon-dev = <&devctrl 0x248>;
+		};
+
+		dspgpio3: keystone_dsp_gpio@262024c {
+			compatible = "ti,keystone-dsp-gpio";
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio,syscon-dev = <&devctrl 0x24c>;
+		};
+
+		mdio: mdio@26200f00 {
+			compatible	= "ti,keystone_mdio", "ti,davinci_mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x26200f00 0x100>;
+			status = "disabled";
+			clocks = <&clkcpgmac>;
+			clock-names = "fck";
+			bus_freq	= <2500000>;
+		};
+		/include/ "k2l-netcp.dtsi"
+	};
+};
+
+&spi0 {
+       ti,davinci-spi-num-cs = <5>;
+};
+
+&spi1 {
+       ti,davinci-spi-num-cs = <3>;
+};
+
+&spi2 {
+       ti,davinci-spi-num-cs = <5>;
+       /* Pin muxed. Enabled and configured by Bootloader */
+       status = "disabled";
+};

arch/arm/dts/keystone-clocks.dtsi

@@ -0,0 +1,414 @@
+/*
+ * Device Tree Source for Keystone 2 clock tree
+ *
+ * Copyright (C) 2013 Texas Instruments, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+clocks {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	ranges;
+
+	mainmuxclk: mainmuxclk@2310108 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,pll-mux-clock";
+		clocks = <&mainpllclk>, <&refclksys>;
+		reg = <0x02310108 4>;
+		bit-shift = <23>;
+		bit-mask = <1>;
+		clock-output-names = "mainmuxclk";
+	};
+
+	chipclk1: chipclk1 {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&mainmuxclk>;
+		clock-div = <1>;
+		clock-mult = <1>;
+		clock-output-names = "chipclk1";
+	};
+
+	chipclk1rstiso: chipclk1rstiso {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&mainmuxclk>;
+		clock-div = <1>;
+		clock-mult = <1>;
+		clock-output-names = "chipclk1rstiso";
+	};
+
+	gemtraceclk: gemtraceclk@2310120 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,pll-divider-clock";
+		clocks = <&mainmuxclk>;
+		reg = <0x02310120 4>;
+		bit-shift = <0>;
+		bit-mask = <8>;
+		clock-output-names = "gemtraceclk";
+	};
+
+	chipstmxptclk: chipstmxptclk {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,pll-divider-clock";
+		clocks = <&mainmuxclk>;
+		reg = <0x02310164 4>;
+		bit-shift = <0>;
+		bit-mask = <8>;
+		clock-output-names = "chipstmxptclk";
+	};
+
+	chipclk12: chipclk12 {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&chipclk1>;
+		clock-div = <2>;
+		clock-mult = <1>;
+		clock-output-names = "chipclk12";
+	};
+
+	chipclk13: chipclk13 {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&chipclk1>;
+		clock-div = <3>;
+		clock-mult = <1>;
+		clock-output-names = "chipclk13";
+	};
+
+	paclk13: paclk13 {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&papllclk>;
+		clock-div = <3>;
+		clock-mult = <1>;
+		clock-output-names = "paclk13";
+	};
+
+	chipclk14: chipclk14 {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&chipclk1>;
+		clock-div = <4>;
+		clock-mult = <1>;
+		clock-output-names = "chipclk14";
+	};
+
+	chipclk16: chipclk16 {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&chipclk1>;
+		clock-div = <6>;
+		clock-mult = <1>;
+		clock-output-names = "chipclk16";
+	};
+
+	chipclk112: chipclk112 {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&chipclk1>;
+		clock-div = <12>;
+		clock-mult = <1>;
+		clock-output-names = "chipclk112";
+	};
+
+	chipclk124: chipclk124 {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&chipclk1>;
+		clock-div = <24>;
+		clock-mult = <1>;
+		clock-output-names = "chipclk114";
+	};
+
+	chipclk1rstiso13: chipclk1rstiso13 {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&chipclk1rstiso>;
+		clock-div = <3>;
+		clock-mult = <1>;
+		clock-output-names = "chipclk1rstiso13";
+	};
+
+	chipclk1rstiso14: chipclk1rstiso14 {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&chipclk1rstiso>;
+		clock-div = <4>;
+		clock-mult = <1>;
+		clock-output-names = "chipclk1rstiso14";
+	};
+
+	chipclk1rstiso16: chipclk1rstiso16 {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&chipclk1rstiso>;
+		clock-div = <6>;
+		clock-mult = <1>;
+		clock-output-names = "chipclk1rstiso16";
+	};
+
+	chipclk1rstiso112: chipclk1rstiso112 {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&chipclk1rstiso>;
+		clock-div = <12>;
+		clock-mult = <1>;
+		clock-output-names = "chipclk1rstiso112";
+	};
+
+	clkmodrst0: clkmodrst0 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk16>;
+		clock-output-names = "modrst0";
+		reg = <0x02350000 0xb00>, <0x02350000 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <0>;
+	};
+
+
+	clkusb: clkusb {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk16>;
+		clock-output-names = "usb";
+		reg = <0x02350008 0xb00>, <0x02350000 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <0>;
+	};
+
+	clkaemifspi: clkaemifspi {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk16>;
+		clock-output-names = "aemif-spi";
+		reg = <0x0235000c 0xb00>, <0x02350000 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <0>;
+	};
+
+
+	clkdebugsstrc: clkdebugsstrc {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk13>;
+		clock-output-names = "debugss-trc";
+		reg = <0x02350014 0xb00>, <0x02350000 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <1>;
+	};
+
+	clktetbtrc: clktetbtrc {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk13>;
+		clock-output-names = "tetb-trc";
+		reg = <0x02350018 0xb00>, <0x02350004 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <1>;
+	};
+
+	clkpa: clkpa {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&paclk13>;
+		clock-output-names = "pa";
+		reg = <0x0235001c 0xb00>, <0x02350008 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <2>;
+	};
+
+	clkcpgmac: clkcpgmac {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&clkpa>;
+		clock-output-names = "cpgmac";
+		reg = <0x02350020 0xb00>, <0x02350008 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <2>;
+	};
+
+	clksa: clksa {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&clkpa>;
+		clock-output-names = "sa";
+		reg = <0x02350024 0xb00>, <0x02350008 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <2>;
+	};
+
+	clkpcie: clkpcie {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk12>;
+		clock-output-names = "pcie";
+		reg = <0x02350028 0xb00>, <0x0235000c 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <3>;
+	};
+
+	clksr: clksr {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk1rstiso112>;
+		clock-output-names = "sr";
+		reg = <0x02350034 0xb00>, <0x02350018 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <6>;
+	};
+
+	clkgem0: clkgem0 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk1>;
+		clock-output-names = "gem0";
+		reg = <0x0235003c 0xb00>, <0x02350020 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <8>;
+	};
+
+	clkddr30: clkddr30 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&chipclk12>;
+		clock-output-names = "ddr3-0";
+		reg = <0x0235005c 0xb00>, <0x02350040 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <16>;
+	};
+
+	clkwdtimer0: clkwdtimer0 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&clkmodrst0>;
+		clock-output-names = "timer0";
+		reg = <0x02350000 0xb00>, <0x02350000 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <0>;
+	};
+
+	clkwdtimer1: clkwdtimer1 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&clkmodrst0>;
+		clock-output-names = "timer1";
+		reg = <0x02350000 0xb00>, <0x02350000 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <0>;
+	};
+
+	clkwdtimer2: clkwdtimer2 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&clkmodrst0>;
+		clock-output-names = "timer2";
+		reg = <0x02350000 0xb00>, <0x02350000 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <0>;
+	};
+
+	clkwdtimer3: clkwdtimer3 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&clkmodrst0>;
+		clock-output-names = "timer3";
+		reg = <0x02350000 0xb00>, <0x02350000 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <0>;
+	};
+
+	clktimer15: clktimer15 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&clkmodrst0>;
+		clock-output-names = "timer15";
+		reg = <0x02350000 0xb00>, <0x02350000 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <0>;
+	};
+
+	clkuart0: clkuart0 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&clkmodrst0>;
+		clock-output-names = "uart0";
+		reg = <0x02350000 0xb00>, <0x02350000 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <0>;
+	};
+
+	clkuart1: clkuart1 {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&clkmodrst0>;
+		clock-output-names = "uart1";
+		reg = <0x02350000 0xb00>, <0x02350000 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <0>;
+	};
+
+	clkaemif: clkaemif {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&clkaemifspi>;
+		clock-output-names = "aemif";
+		reg = <0x02350000 0xb00>, <0x02350000 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <0>;
+	};
+
+	clkusim: clkusim {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&clkmodrst0>;
+		clock-output-names = "usim";
+		reg = <0x02350000 0xb00>, <0x02350000 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <0>;
+	};
+
+	clki2c: clki2c {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&clkmodrst0>;
+		clock-output-names = "i2c";
+		reg = <0x02350000 0xb00>, <0x02350000 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <0>;
+	};
+
+	clkspi: clkspi {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&clkaemifspi>;
+		clock-output-names = "spi";
+		reg = <0x02350000 0xb00>, <0x02350000 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <0>;
+	};
+
+	clkgpio: clkgpio {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&clkmodrst0>;
+		clock-output-names = "gpio";
+		reg = <0x02350000 0xb00>, <0x02350000 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <0>;
+	};
+
+	clkkeymgr: clkkeymgr {
+		#clock-cells = <0>;
+		compatible = "ti,keystone,psc-clock";
+		clocks = <&clkmodrst0>;
+		clock-output-names = "keymgr";
+		reg = <0x02350000 0xb00>, <0x02350000 0x400>;
+		reg-names = "control", "domain";
+		domain-id = <0>;
+	};
+};

arch/arm/dts/keystone.dtsi

@@ -0,0 +1,327 @@
+/*
+ * Copyright 2013 Texas Instruments, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/gpio/gpio.h>
+
+#include "skeleton.dtsi"
+
+/ {
+	model = "Texas Instruments Keystone 2 SoC";
+	#address-cells = <1>;
+	#size-cells = <1>;
+	interrupt-parent = <&gic>;
+
+	aliases {
+		serial0	= &uart0;
+	};
+
+	chosen {
+		stdout-path = &uart0;
+	};
+
+	memory {
+		reg = <0x80000000 0x40000000>;
+	};
+
+	gic: interrupt-controller {
+		compatible = "arm,cortex-a15-gic";
+		#interrupt-cells = <3>;
+		interrupt-controller;
+		reg = <0x02561000 0x1000>,
+		      <0x02562000 0x2000>,
+		      <0x02564000 0x1000>,
+		      <0x02566000 0x2000>;
+		interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) |
+				IRQ_TYPE_LEVEL_HIGH)>;
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts =
+			<GIC_PPI 13
+				(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 14
+				(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 11
+				(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 10
+				(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	pmu {
+		compatible = "arm,cortex-a15-pmu";
+		interrupts = <GIC_SPI 20 IRQ_TYPE_EDGE_RISING>,
+			     <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>,
+			     <GIC_SPI 22 IRQ_TYPE_EDGE_RISING>,
+			     <GIC_SPI 23 IRQ_TYPE_EDGE_RISING>;
+	};
+
+	soc {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "ti,keystone","simple-bus";
+		interrupt-parent = <&gic>;
+		ranges;
+
+		pllctrl: pll-controller@02310000 {
+			compatible = "ti,keystone-pllctrl", "syscon";
+			reg = <0x02310000 0x200>;
+		};
+
+		devctrl: device-state-control@02620000 {
+			compatible = "ti,keystone-devctrl", "syscon";
+			reg = <0x02620000 0x1000>;
+		};
+
+		rstctrl: reset-controller {
+			compatible = "ti,keystone-reset";
+			ti,syscon-pll = <&pllctrl 0xe4>;
+			ti,syscon-dev = <&devctrl 0x328>;
+			ti,wdt-list = <0>;
+		};
+
+		/include/ "keystone-clocks.dtsi"
+
+		uart0: serial@02530c00 {
+			compatible = "ns16550a";
+			current-speed = <115200>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			reg = <0x02530c00 0x100>;
+			clocks	= <&clkuart0>;
+			interrupts = <GIC_SPI 277 IRQ_TYPE_EDGE_RISING>;
+		};
+
+		uart1:	serial@02531000 {
+			compatible = "ns16550a";
+			current-speed = <115200>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			reg = <0x02531000 0x100>;
+			clocks	= <&clkuart1>;
+			interrupts = <GIC_SPI 280 IRQ_TYPE_EDGE_RISING>;
+		};
+
+		i2c0: i2c@2530000 {
+			compatible = "ti,davinci-i2c";
+			reg = <0x02530000 0x400>;
+			clock-frequency = <100000>;
+			clocks = <&clki2c>;
+			interrupts = <GIC_SPI 283 IRQ_TYPE_EDGE_RISING>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c1: i2c@2530400 {
+			compatible = "ti,davinci-i2c";
+			reg = <0x02530400 0x400>;
+			clock-frequency = <100000>;
+			clocks = <&clki2c>;
+			interrupts = <GIC_SPI 286 IRQ_TYPE_EDGE_RISING>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c2: i2c@2530800 {
+			compatible = "ti,davinci-i2c";
+			reg = <0x02530800 0x400>;
+			clock-frequency = <100000>;
+			clocks = <&clki2c>;
+			interrupts = <GIC_SPI 289 IRQ_TYPE_EDGE_RISING>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		spi0: spi@21000400 {
+			compatible = "ti,dm6441-spi";
+			reg = <0x21000400 0x200>;
+			num-cs = <4>;
+			ti,davinci-spi-intr-line = <0>;
+			interrupts = <GIC_SPI 292 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&clkspi>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		spi1: spi@21000600 {
+			compatible = "ti,dm6441-spi";
+			reg = <0x21000600 0x200>;
+			num-cs = <4>;
+			ti,davinci-spi-intr-line = <0>;
+			interrupts = <GIC_SPI 296 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&clkspi>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		spi2: spi@21000800 {
+			compatible = "ti,dm6441-spi";
+			reg = <0x21000800 0x200>;
+			num-cs = <4>;
+			ti,davinci-spi-intr-line = <0>;
+			interrupts = <GIC_SPI 300 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&clkspi>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		usb_phy: usb_phy@2620738 {
+			compatible = "ti,keystone-usbphy";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x2620738 24>;
+			status = "disabled";
+		};
+
+		usb: usb@2680000 {
+			compatible = "ti,keystone-dwc3";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x2680000 0x10000>;
+			clocks = <&clkusb>;
+			clock-names = "usb";
+			interrupts = <GIC_SPI 393 IRQ_TYPE_EDGE_RISING>;
+			ranges;
+			dma-coherent;
+			dma-ranges;
+			status = "disabled";
+
+			dwc3@2690000 {
+				compatible = "synopsys,dwc3";
+				reg = <0x2690000 0x70000>;
+				interrupts = <GIC_SPI 393 IRQ_TYPE_EDGE_RISING>;
+				usb-phy = <&usb_phy>, <&usb_phy>;
+			};
+		};
+
+		wdt: wdt@022f0080 {
+			compatible = "ti,keystone-wdt","ti,davinci-wdt";
+			reg = <0x022f0080 0x80>;
+			clocks = <&clkwdtimer0>;
+		};
+
+		clock_event: timer@22f0000 {
+			compatible = "ti,keystone-timer";
+			reg = <0x022f0000 0x80>;
+			interrupts = <GIC_SPI 110 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&clktimer15>;
+		};
+
+		gpio0: gpio@260bf00 {
+			compatible = "ti,keystone-gpio";
+			reg = <0x0260bf00 0x100>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			/* HW Interrupts mapped to GPIO pins */
+			interrupts = <GIC_SPI 120 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 121 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 122 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 123 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 124 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 125 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 126 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 127 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 128 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 129 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 130 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 131 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 132 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 133 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 134 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 135 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 136 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 137 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 138 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 139 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 140 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 141 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 142 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 143 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 144 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 145 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 146 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 147 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 148 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 149 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 150 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 151 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&clkgpio>;
+			clock-names = "gpio";
+			ti,ngpio = <32>;
+			ti,davinci-gpio-unbanked = <32>;
+		};
+
+		aemif: aemif@21000A00 {
+			compatible = "ti,keystone-aemif", "ti,davinci-aemif";
+			#address-cells = <2>;
+			#size-cells = <1>;
+			clocks = <&clkaemif>;
+			clock-names = "aemif";
+			clock-ranges;
+
+			reg = <0x21000A00 0x00000100>;
+			ranges = <0 0 0x30000000 0x10000000
+				  1 0 0x21000A00 0x00000100>;
+		};
+
+		kirq0: keystone_irq@26202a0 {
+			compatible = "ti,keystone-irq";
+			interrupts = <GIC_SPI 4 IRQ_TYPE_EDGE_RISING>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			ti,syscon-dev = <&devctrl 0x2a0>;
+		};
+
+		pcie0: pcie@21800000 {
+			compatible = "ti,keystone-pcie", "snps,dw-pcie";
+			clocks = <&clkpcie>;
+			clock-names = "pcie";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			reg =  <0x21801000 0x2000>, <0x21800000 0x1000>, <0x02620128 4>;
+			ranges = <0x81000000 0 0 0x23250000 0 0x4000
+				0x82000000 0 0x50000000 0x50000000 0 0x10000000>;
+
+			status = "disabled";
+			device_type = "pci";
+			num-lanes = <2>;
+
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 7>;
+			interrupt-map = <0 0 0 1 &pcie_intc0 0>, /* INT A */
+					<0 0 0 2 &pcie_intc0 1>, /* INT B */
+					<0 0 0 3 &pcie_intc0 2>, /* INT C */
+					<0 0 0 4 &pcie_intc0 3>; /* INT D */
+
+			pcie_msi_intc0: msi-interrupt-controller {
+				interrupt-controller;
+				#interrupt-cells = <1>;
+				interrupt-parent = <&gic>;
+				interrupts = <GIC_SPI 30 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 31 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 32 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 33 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 34 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 35 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 36 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 37 IRQ_TYPE_EDGE_RISING>;
+			};
+
+			pcie_intc0: legacy-interrupt-controller {
+				interrupt-controller;
+				#interrupt-cells = <1>;
+				interrupt-parent = <&gic>;
+				interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 27 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 28 IRQ_TYPE_EDGE_RISING>,
+					<GIC_SPI 29 IRQ_TYPE_EDGE_RISING>;
+			};
+		};
+	};
+};

arch/arm/dts/socfpga_cyclone5_socdk.dts

@@ -89,7 +89,7 @@
 		#size-cells = <1>;
 		compatible = "n25q00";
 		reg = <0>;      /* chip select */
-		spi-max-frequency = <50000000>;
+		spi-max-frequency = <100000000>;
 		m25p,fast-read;
 		page-size = <256>;
 		block-size = <16>; /* 2^16, 64KB */

arch/arm/dts/sun5i-a10s.dtsi

@@ -77,6 +77,15 @@
 			clocks = <&pll5 1>, <&ahb_gates 36>, <&ahb_gates 44>;
 			status = "disabled";
 		};
+
+		framebuffer@2 {
+			compatible = "allwinner,simple-framebuffer",
+				     "simple-framebuffer";
+			allwinner,pipeline = "de_be0-lcd0-tve0";
+			clocks = <&pll5 1>, <&ahb_gates 34>, <&ahb_gates 36>,
+				 <&ahb_gates 44>;
+			status = "disabled";
+		};
 	};
 
 	clocks {
@@ -85,6 +94,17 @@
 			compatible = "allwinner,sun5i-a10s-ahb-gates-clk";
 			reg = <0x01c20060 0x8>;
 			clocks = <&ahb>;
+			clock-indices = <0>, <1>,
+					<2>, <5>, <6>,
+					<7>, <8>, <9>,
+					<10>, <13>,
+					<14>, <17>, <18>,
+					<20>, <21>, <22>,
+					<26>, <28>, <32>,
+					<34>, <36>, <40>,
+					<43>, <44>,
+					<46>, <51>,
+					<52>;
 			clock-output-names = "ahb_usbotg", "ahb_ehci",
 					     "ahb_ohci", "ahb_ss", "ahb_dma",
 					     "ahb_bist", "ahb_mmc0", "ahb_mmc1",
@@ -103,6 +123,9 @@
 			compatible = "allwinner,sun5i-a10s-apb0-gates-clk";
 			reg = <0x01c20068 0x4>;
 			clocks = <&apb0>;
+			clock-indices = <0>, <3>,
+					<5>, <6>,
+					<10>;
 			clock-output-names = "apb0_codec", "apb0_iis",
 					     "apb0_pio", "apb0_ir",
 					     "apb0_keypad";
@@ -113,9 +136,14 @@
 			compatible = "allwinner,sun5i-a10s-apb1-gates-clk";
 			reg = <0x01c2006c 0x4>;
 			clocks = <&apb1>;
+			clock-indices = <0>, <1>,
+					<2>, <16>,
+					<17>, <18>,
+					<19>;
 			clock-output-names = "apb1_i2c0", "apb1_i2c1",
-				"apb1_i2c2", "apb1_uart0", "apb1_uart1",
-				"apb1_uart2", "apb1_uart3";
+					     "apb1_i2c2", "apb1_uart0",
+					     "apb1_uart1", "apb1_uart2",
+					     "apb1_uart3";
 		};
 	};
 
@@ -137,6 +165,14 @@
 			#size-cells = <0>;
 		};
 
+		pwm: pwm@01c20e00 {
+			compatible = "allwinner,sun5i-a10s-pwm";
+			reg = <0x01c20e00 0xc>;
+			clocks = <&osc24M>;
+			#pwm-cells = <3>;
+			status = "disabled";
+		};
+
 		uart0: serial@01c28000 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0x01c28000 0x400>;
@@ -176,13 +212,6 @@
 		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
 	};
 
-	uart3_pins_a: uart3@0 {
-		allwinner,pins = "PG9", "PG10";
-		allwinner,function = "uart3";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-	};
-
 	emac_pins_a: emac0@0 {
 		allwinner,pins = "PA0", "PA1", "PA2",
 				"PA3", "PA4", "PA5", "PA6",