Prepare v2016.09-rc2

Signed-off-by: Tom Rini <trini@konsulko.com>

Kconfig

@@ -57,7 +57,8 @@ config DISTRO_DEFAULTS
 	bool "Select defaults suitable for booting general purpose Linux distributions"
 	default y if ARCH_SUNXI
 	default n
-	select CMD_BOOTZ
+	select CMD_BOOTZ if ARM && !ARM64
+	select CMD_BOOTI if ARM64
 	select CMD_DHCP
 	select CMD_EXT2
 	select CMD_EXT4
@@ -124,6 +125,14 @@ config TOOLS_DEBUG
 	  debug through the source code, etc.
 
 endif
+
+config PHYS_64BIT
+	bool "64bit physical address support"
+	help
+	  Say Y here to support 64bit physical memory address.
+	  This can be used not only for 64bit SoCs, but also for
+	  large physical address extention on 32bit SoCs.
+
 endmenu		# General setup
 
 menu "Boot images"
@@ -336,12 +345,35 @@ config SPL_FIT_IMAGE_POST_PROCESS
 	  injected into the FIT creation (i.e. the blobs would have been pre-
 	  processed before being added to the FIT image).
 
+config FIT_IMAGE_POST_PROCESS
+	bool "Enable post-processing of FIT artifacts after loading by U-Boot"
+	depends on FIT && TI_SECURE_DEVICE
+	help
+	  Allows doing any sort of manipulation to blobs after they got extracted
+	  from FIT images like stripping off headers or modifying the size of the
+	  blob, verification, authentication, decryption etc. in a platform or
+	  board specific way. In order to use this feature a platform or board-
+	  specific implementation of board_fit_image_post_process() must be
+	  provided. Also, anything done during this post-processing step would
+	  need to be comprehended in how the images were prepared before being
+	  injected into the FIT creation (i.e. the blobs would have been pre-
+	  processed before being added to the FIT image).
+
 config SYS_CLK_FREQ
 	depends on ARC || ARCH_SUNXI
 	int "CPU clock frequency"
 	help
 	  TODO: Move CONFIG_SYS_CLK_FREQ for all the architecture
 
+config ARCH_FIXUP_FDT
+	bool "Enable arch_fixup_fdt() call"
+	depends on ARM || MIPS
+	default y
+	help
+	  Enable FDT memory map syncup before OS boot. This feature can be
+	  used for booting OS with different memory setup where the part of
+	  the memory location should be used for different purpose.
+
 endmenu		# Boot images
 
 source "common/Kconfig"

MAINTAINERS

@@ -102,6 +102,7 @@ F:	arch/arm/include/asm/arch-imx/
 F:	arch/arm/include/asm/arch-mx*/
 F:	arch/arm/include/asm/arch-vf610/
 F:	arch/arm/include/asm/imx-common/
+F:	board/freescale/*mx*/
 
 ARM HISILICON
 M:	Peter Griffin <peter.griffin@linaro.org>
@@ -125,6 +126,12 @@ T:	git git://git.denx.de/u-boot-pxa.git
 F:	arch/arm/cpu/pxa/
 F:	arch/arm/include/asm/arch-pxa/
 
+ARM RENESAS RMOBILE/R-CAR
+M:	Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
+S:	Maintained
+T:	git git://git.denx.de/u-boot-sh.git
+F:	arch/arm/mach-rmobile/
+
 ARM ROCKCHIP
 M:	Simon Glass <sjg@chromium.org>
 S:	Maintained
@@ -298,7 +305,7 @@ T:	git git://git.denx.de/u-boot-mips.git
 F:	arch/mips/
 
 MMC
-M:	Pantelis Antoniou <panto@antoniou-consulting.com>
+M:	Jaehoon Chung <jh80.chung@samsung.com>
 S:	Maintained
 T:	git git://git.denx.de/u-boot-mmc.git
 F:	drivers/mmc/
@@ -453,6 +460,11 @@ S:	Maintained
 T:	git git://git.denx.de/u-boot-x86.git
 F:	arch/x86/
 
+XTENSA
+M:	Max Filippov <jcmvbkbc@gmail.com>
+S:	Maintained
+F:	arch/xtensa/
+
 THE REST
 M:	Tom Rini <trini@konsulko.com>
 L:	u-boot@lists.denx.de

MAKEALL

@@ -1,850 +0,0 @@
-#!/bin/bash
-# Tool mainly for U-Boot Quality Assurance: build one or more board
-# configurations with minimal verbosity, showing only warnings and
-# errors.
-#
-# SPDX-License-Identifier:	GPL-2.0+
-
-usage()
-{
-	# if exiting with 0, write to stdout, else write to stderr
-	local ret=${1:-0}
-	[ "${ret}" -eq 1 ] && exec 1>&2
-	cat <<-EOF
-	Usage: MAKEALL [options] [--] [boards-to-build]
-
-	Options:
-	  -a ARCH,   --arch ARCH       Build all boards with arch ARCH
-	  -c CPU,    --cpu CPU         Build all boards with cpu CPU
-	  -v VENDOR, --vendor VENDOR   Build all boards with vendor VENDOR
-	  -s SOC,    --soc SOC         Build all boards with soc SOC
-	  -b BOARD,  --board BOARD     Build all boards with board name BOARD
-	  -l,        --list            List all targets to be built
-	  -m,        --maintainers     List all targets and maintainer email
-	  -M,        --mails           List all targets and all affilated emails
-	  -C,        --check           Enable build checking
-	  -n,        --continue        Continue (skip boards already built)
-	  -r,        --rebuild-errors  Rebuild any boards that errored
-	  -h,        --help            This help output
-
-	Selections by these options are logically ANDed; if the same option
-	is used repeatedly, such selections are ORed.  So "-v FOO -v BAR"
-	will select all configurations where the vendor is either FOO or
-	BAR.  Any additional arguments specified on the command line are
-	always build additionally.  See the boards.cfg file for more info.
-
-	If no boards are specified, then the default is "powerpc".
-
-	Environment variables:
-	  BUILD_NCPUS      number of parallel make jobs (default: auto)
-	  CROSS_COMPILE    cross-compiler toolchain prefix (default: "")
-	  CROSS_COMPILE_<ARCH> cross-compiler toolchain prefix for
-			   architecture "ARCH".  Substitute "ARCH" for any
-			   supported architecture (default: "")
-	  MAKEALL_LOGDIR   output all logs to here (default: ./LOG/)
-	  BUILD_DIR        output build directory (default: ./)
-	  BUILD_NBUILDS	   number of parallel targets (default: 1)
-
-	Examples:
-	  - build all Power Architecture boards:
-	      MAKEALL -a powerpc
-	      MAKEALL --arch powerpc
-	      MAKEALL powerpc
-	  - build all PowerPC boards manufactured by vendor "esd":
-	      MAKEALL -a powerpc -v esd
-	  - build all PowerPC boards manufactured either by "keymile" or "siemens":
-	      MAKEALL -a powerpc -v keymile -v siemens
-	  - build all Freescale boards with MPC83xx CPUs, plus all 4xx boards:
-	      MAKEALL -c mpc83xx -v freescale 4xx
-	EOF
-	exit ${ret}
-}
-
-deprecation() {
-	echo "** Note: MAKEALL is deprecated - please use buildman instead"
-	echo "** See tools/buildman/README for details"
-	echo
-}
-
-deprecation
-
-SHORT_OPTS="ha:c:v:s:b:lmMCnr"
-LONG_OPTS="help,arch:,cpu:,vendor:,soc:,board:,list,maintainers,mails,check,continue,rebuild-errors"
-
-# Option processing based on util-linux-2.13/getopt-parse.bash
-
-# Note that we use `"$@"' to let each command-line parameter expand to a
-# separate word. The quotes around `$@' are essential!
-# We need TEMP as the `eval set --' would nuke the return value of
-# getopt.
-TEMP=`getopt -o ${SHORT_OPTS} --long ${LONG_OPTS} \
-     -n 'MAKEALL' -- "$@"`
-
-[ $? != 0 ] && usage 1
-
-# Note the quotes around `$TEMP': they are essential!
-eval set -- "$TEMP"
-
-SELECTED=''
-ONLY_LIST=''
-PRINT_MAINTS=''
-MAINTAINERS_ONLY=''
-CONTINUE=''
-REBUILD_ERRORS=''
-
-while true ; do
-	case "$1" in
-	-a|--arch)
-		# echo "Option ARCH: argument \`$2'"
-		if [ "$opt_a" ] ; then
-			opt_a="${opt_a%)} || \$2 == \"$2\")"
-		else
-			opt_a="(\$2 == \"$2\")"
-		fi
-		SELECTED='y'
-		shift 2 ;;
-	-c|--cpu)
-		# echo "Option CPU: argument \`$2'"
-		if [ "$opt_c" ] ; then
-			opt_c="${opt_c%)} || \$3 == \"$2\" || \$3 ~ /$2:/)"
-		else
-			opt_c="(\$3 == \"$2\" || \$3 ~ /$2:/)"
-		fi
-		SELECTED='y'
-		shift 2 ;;
-	-s|--soc)
-		# echo "Option SoC: argument \`$2'"
-		if [ "$opt_s" ] ; then
-			opt_s="${opt_s%)} || \$4 == \"$2\" || \$4 ~ /$2/)"
-		else
-			opt_s="(\$4 == \"$2\" || \$4 ~ /$2/)"
-		fi
-		SELECTED='y'
-		shift 2 ;;
-	-v|--vendor)
-		# echo "Option VENDOR: argument \`$2'"
-		if [ "$opt_v" ] ; then
-			opt_v="${opt_v%)} || \$5 == \"$2\")"
-		else
-			opt_v="(\$5 == \"$2\")"
-		fi
-		SELECTED='y'
-		shift 2 ;;
-	-b|--board)
-		# echo "Option BOARD: argument \`$2'"
-		if [ "$opt_b" ] ; then
-			opt_b="${opt_b%)} || \$6 == \"$2\" || \$7 == \"$2\")"
-		else
-			# We need to check the 7th field too
-			# for boards whose 6th field is "-"
-			opt_b="(\$6 == \"$2\" || \$7 == \"$2\")"
-		fi
-		SELECTED='y'
-		shift 2 ;;
-	-C|--check)
-		CHECK='C=1'
-		shift ;;
-	-n|--continue)
-		CONTINUE='y'
-		shift ;;
-	-r|--rebuild-errors)
-		REBUILD_ERRORS='y'
-		shift ;;
-	-l|--list)
-		ONLY_LIST='y'
-		shift ;;
-	-m|--maintainers)
-		ONLY_LIST='y'
-		PRINT_MAINTS='y'
-		MAINTAINERS_ONLY='y'
-		shift ;;
-	-M|--mails)
-		ONLY_LIST='y'
-		PRINT_MAINTS='y'
-		shift ;;
-	-h|--help)
-		usage ;;
-	--)
-		shift ; break ;;
-	*)
-		echo "Internal error!" >&2 ; exit 1 ;;
-	esac
-done
-
-GNU_MAKE=$(scripts/show-gnu-make) || {
-	echo "GNU Make not found" >&2
-	exit 1
-}
-
-# echo "Remaining arguments:"
-# for arg do echo '--> '"\`$arg'" ; done
-
-tools/genboardscfg.py || {
-	echo "Failed to generate boards.cfg" >&2
-	exit 1
-}
-
-FILTER="\$1 !~ /^#/"
-[ "$opt_a" ] && FILTER="${FILTER} && $opt_a"
-[ "$opt_c" ] && FILTER="${FILTER} && $opt_c"
-[ "$opt_s" ] && FILTER="${FILTER} && $opt_s"
-[ "$opt_v" ] && FILTER="${FILTER} && $opt_v"
-[ "$opt_b" ] && FILTER="${FILTER} && $opt_b"
-
-if [ "$SELECTED" ] ; then
-	SELECTED=$(awk '('"$FILTER"') { print $7 }' boards.cfg)
-
-	# Make sure some boards from boards.cfg are actually found
-	if [ -z "$SELECTED" ] ; then
-		echo "Error: No boards selected, invalid arguments"
-		exit 1
-	fi
-fi
-
-#########################################################################
-
-# Print statistics when we exit
-trap exit 1 2 3 15
-trap print_stats 0
-
-# Determine number of CPU cores if no default was set
-: ${BUILD_NCPUS:="`getconf _NPROCESSORS_ONLN`"}
-
-if [ "$BUILD_NCPUS" -gt 1 ]
-then
-	JOBS="-j $((BUILD_NCPUS + 1))"
-else
-	JOBS=""
-fi
-
-if [ "${MAKEALL_LOGDIR}" ] ; then
-	LOG_DIR=${MAKEALL_LOGDIR}
-else
-	LOG_DIR="LOG"
-fi
-
-: ${BUILD_NBUILDS:=1}
-BUILD_MANY=0
-
-if [ "${BUILD_NBUILDS}" -gt 1 ] ; then
-	BUILD_MANY=1
-	: ${BUILD_DIR:=./build}
-	mkdir -p "${BUILD_DIR}/ERR"
-	find "${BUILD_DIR}/ERR/" -type f -exec rm -f {} +
-fi
-
-: ${BUILD_DIR:=.}
-
-OUTPUT_PREFIX="${BUILD_DIR}"
-
-[ -d ${LOG_DIR} ] || mkdir "${LOG_DIR}" || exit 1
-if [ "$CONTINUE" != 'y' -a "$REBUILD_ERRORS" != 'y' ] ; then
-	find "${LOG_DIR}/" -type f -exec rm -f {} +
-fi
-
-LIST=""
-
-# Keep track of the number of builds and errors
-ERR_CNT=0
-ERR_LIST=""
-WRN_CNT=0
-WRN_LIST=""
-TOTAL_CNT=0
-SKIP_CNT=0
-CURRENT_CNT=0
-OLDEST_IDX=1
-RC=0
-
-# Helper funcs for parsing boards.cfg
-targets_by_field()
-{
-	field=$1
-	regexp=$2
-
-	awk '($1 !~ /^#/ && $'"$field"' ~ /^'"$regexp"'$/) { print $7 }' \
-								boards.cfg
-}
-
-targets_by_arch() { targets_by_field 2 "$@" ; }
-targets_by_cpu()  { targets_by_field 3 "$@" ; targets_by_field 3 "$@:.*" ; }
-targets_by_soc()  { targets_by_field 4 "$@" ; }
-
-#########################################################################
-## MPC5xx Systems
-#########################################################################
-
-LIST_5xx="$(targets_by_cpu mpc5xx)"
-
-#########################################################################
-## MPC5xxx Systems
-#########################################################################
-
-LIST_5xxx="$(targets_by_cpu mpc5xxx)"
-
-#########################################################################
-## MPC512x Systems
-#########################################################################
-
-LIST_512x="$(targets_by_cpu mpc512x)"
-
-#########################################################################
-## MPC8xx Systems
-#########################################################################
-
-LIST_8xx="$(targets_by_cpu mpc8xx)"
-
-#########################################################################
-## PPC4xx Systems
-#########################################################################
-
-LIST_4xx="$(targets_by_cpu ppc4xx)"
-
-#########################################################################
-## MPC8260 Systems (includes 8250, 8255 etc.)
-#########################################################################
-
-LIST_8260="$(targets_by_cpu mpc8260)"
-
-#########################################################################
-## MPC83xx Systems (includes 8349, etc.)
-#########################################################################
-
-LIST_83xx="$(targets_by_cpu mpc83xx)"
-
-#########################################################################
-## MPC85xx Systems (includes 8540, 8560 etc.)
-#########################################################################
-
-LIST_85xx="$(targets_by_cpu mpc85xx)"
-
-#########################################################################
-## MPC86xx Systems
-#########################################################################
-
-LIST_86xx="$(targets_by_cpu mpc86xx)"
-
-#########################################################################
-## PowerPC groups
-#########################################################################
-
-LIST_TSEC="		\
-	${LIST_83xx}	\
-	${LIST_85xx}	\
-	${LIST_86xx}	\
-"
-
-LIST_powerpc="		\
-	${LIST_5xx}	\
-	${LIST_512x}	\
-	${LIST_5xxx}	\
-	${LIST_8xx}	\
-	${LIST_824x}	\
-	${LIST_8260}	\
-	${LIST_83xx}	\
-	${LIST_85xx}	\
-	${LIST_86xx}	\
-	${LIST_4xx}	\
-"
-
-# Alias "ppc" -> "powerpc" to not break compatibility with older scripts
-# still using "ppc" instead of "powerpc"
-LIST_ppc="		\
-	${LIST_powerpc}	\
-"
-
-#########################################################################
-## StrongARM Systems
-#########################################################################
-
-LIST_SA="$(targets_by_cpu sa1100)"
-
-#########################################################################
-## ARM7 Systems
-#########################################################################
-
-LIST_ARM7="$(targets_by_cpu arm720t)"
-
-#########################################################################
-## ARM9 Systems
-#########################################################################
-
-LIST_ARM9="$(targets_by_cpu arm920t)	\
-	$(targets_by_cpu arm926ejs)	\
-	$(targets_by_cpu arm946es)	\
-"
-
-#########################################################################
-## ARM11 Systems
-#########################################################################
-LIST_ARM11="$(targets_by_cpu arm1136)	\
-	$(targets_by_cpu arm1176)	\
-"
-
-#########################################################################
-## ARMV7 Systems
-#########################################################################
-
-LIST_ARMV7="$(targets_by_cpu armv7)"
-
-#########################################################################
-## ARMV8 Systems
-#########################################################################
-
-LIST_ARMV8="$(targets_by_cpu armv8)"
-
-#########################################################################
-## AT91 Systems
-#########################################################################
-
-LIST_at91="$(targets_by_soc at91)"
-
-#########################################################################
-## Xscale Systems
-#########################################################################
-
-LIST_pxa="$(targets_by_cpu pxa)"
-
-#########################################################################
-## SPEAr Systems
-#########################################################################
-
-LIST_spear="$(targets_by_soc spear)"
-
-#########################################################################
-## ARM groups
-#########################################################################
-
-LIST_arm="$(targets_by_arch arm |		\
-	for ARMV8_TARGET in $LIST_ARMV8;	\
-		do sed "/$ARMV8_TARGET/d";	\
-	done)					\
-"
-
-#########################################################################
-## MIPS Systems		(default = big endian)
-#########################################################################
-
-LIST_mips="$(targets_by_arch mips)"
-
-#########################################################################
-## OpenRISC Systems
-#########################################################################
-
-LIST_openrisc="$(targets_by_arch openrisc)"
-
-#########################################################################
-## x86 Systems
-#########################################################################
-
-LIST_x86="$(targets_by_arch x86)"
-
-#########################################################################
-## Nios-II Systems
-#########################################################################
-
-LIST_nios2="$(targets_by_arch nios2)"
-
-#########################################################################
-## MicroBlaze Systems
-#########################################################################
-
-LIST_microblaze="$(targets_by_arch microblaze)"
-
-#########################################################################
-## ColdFire Systems
-#########################################################################
-
-LIST_m68k="$(targets_by_arch m68k)"
-LIST_coldfire=${LIST_m68k}
-
-#########################################################################
-## AVR32 Systems
-#########################################################################
-
-LIST_avr32="$(targets_by_arch avr32)"
-
-#########################################################################
-## Blackfin Systems
-#########################################################################
-
-LIST_blackfin="$(targets_by_arch blackfin)"
-
-#########################################################################
-## SH Systems
-#########################################################################
-
-LIST_sh2="$(targets_by_cpu sh2)"
-LIST_sh3="$(targets_by_cpu sh3)"
-LIST_sh4="$(targets_by_cpu sh4)"
-
-LIST_sh="$(targets_by_arch sh)"
-
-#########################################################################
-## SPARC Systems
-#########################################################################
-
-LIST_sparc="$(targets_by_arch sparc)"
-
-#########################################################################
-## NDS32 Systems
-#########################################################################
-
-LIST_nds32="$(targets_by_arch nds32)"
-
-#########################################################################
-## ARC Systems
-#########################################################################
-
-LIST_arc="$(targets_by_arch arc)"
-
-#-----------------------------------------------------------------------
-
-get_target_location() {
-	local target=$1
-	local BOARD_NAME=""
-	local CONFIG_NAME=""
-	local board=""
-	local vendor=""
-
-	# Automatic mode
-	local line=`awk '\$7 == "'"$target"'" { print \$0 }' boards.cfg`
-	if [ -z "${line}" ] ; then echo "" ; return ; fi
-
-	set ${line}
-
-	CONFIG_NAME="${7%_defconfig}"
-
-	[ "${BOARD_NAME}" ] || BOARD_NAME="${7%_defconfig}"
-
-	if [ $# -gt 5 ]; then
-		if [ "$6" = "-" ] ; then
-			board=${BOARD_NAME}
-		else
-			board="$6"
-		fi
-	fi
-
-	[ $# -gt 4 ] && [ "$5" != "-" ] && vendor="$5"
-	[ $# -gt 6 ] && [ "$8" != "-" ] && {
-		tmp="${8%:*}"
-		if [ "$tmp" ] ; then
-			CONFIG_NAME="$tmp"
-		fi
-	}
-
-	# Assign board directory to BOARDIR variable
-	if [ "${vendor}" == "-" ] ; then
-	    BOARDDIR=${board}
-	else
-	    BOARDDIR=${vendor}/${board}
-	fi
-
-	echo "${CONFIG_NAME}:${BOARDDIR}:${BOARD_NAME}"
-}
-
-get_target_maintainers() {
-	local name=`echo $1 | cut -d : -f 3`
-
-	local line=`awk '\$7 == "'"$target"'" { print \$0 }' boards.cfg`
-	if [ -z "${line}" ]; then
-		echo ""
-		return ;
-	fi
-
-	local mails=`echo ${line} | cut -d ' ' -f 9- | sed -e 's/[^<]*<//' -e 's/>.*</ /' -e 's/>[^>]*$//'`
-	[ "$mails" == "-" ] && mails=""
-	echo "$mails"
-}
-
-get_target_arch() {
-	local target=$1
-
-	awk '$7 == "'$target'" { print $2 }' boards.cfg
-}
-
-list_target() {
-	if [ "$PRINT_MAINTS" != 'y' ] ; then
-		echo "$1"
-		return
-	fi
-
-	echo -n "$1:"
-
-	local loc=`get_target_location $1`
-
-	if [ -z "${loc}" ] ; then echo "ERROR" ; return ; fi
-
-	local maintainers_result=`get_target_maintainers ${loc} | tr " " "\n"`
-
-	if [ "$MAINTAINERS_ONLY" != 'y' ] ; then
-
-		local dir=`echo ${loc} | cut -d ":" -f 2`
-		local cfg=`echo ${loc} | cut -d ":" -f 1`
-		local git_result=`git log --format=%aE board/${dir} \
-				include/configs/${cfg}.h | grep "@"`
-		local git_result_recent=`echo ${git_result} | tr " " "\n" | \
-						head -n 3`
-		local git_result_top=`echo ${git_result} | tr " " "\n" | \
-			sort | uniq -c | sort -nr | head -n 3 | \
-			sed "s/^ \+[0-9]\+ \+//"`
-
-		echo -e "$git_result_recent\n$git_result_top\n$maintainers_result" | \
-			sort -u | tr "\n" " " | sed "s/ $//" ;
-	else
-		echo -e "$maintainers_result" | sort -u | tr "\n" " " | \
-						sed "s/ $//" ;
-	fi
-
-	echo ""
-}
-
-# Each finished build will have a file called ${donep}${n},
-# where n is the index of the build. Each build
-# we've already noted as finished will have ${skipp}${n}.
-# The code managing the build process will use this information
-# to ensure that only BUILD_NBUILDS builds are in flight at once
-donep="${LOG_DIR}/._done_"
-skipp="${LOG_DIR}/._skip_"
-
-build_target_killed() {
-	echo "Aborted $target build."
-	# Remove the logs for this board since it was aborted
-	rm -f ${LOG_DIR}/$target.MAKELOG ${LOG_DIR}/$target.ERR
-	exit
-}
-
-build_target() {
-	target=$1
-	build_idx=$2
-
-	if [ "$ONLY_LIST" == 'y' ] ; then
-		list_target ${target}
-		return
-	fi
-
-	if [ $BUILD_MANY == 1 ] ; then
-		output_dir="${OUTPUT_PREFIX}/${target}"
-		mkdir -p "${output_dir}"
-		trap build_target_killed TERM
-	else
-		output_dir="${OUTPUT_PREFIX}"
-	fi
-
-	target_arch=$(get_target_arch ${target})
-	eval cross_toolchain=\$CROSS_COMPILE_`echo $target_arch | tr '[:lower:]' '[:upper:]'`
-	if [ "${cross_toolchain}" ] ; then
-	    MAKE="$GNU_MAKE CROSS_COMPILE=${cross_toolchain}"
-	elif [ "${CROSS_COMPILE}" ] ; then
-	    MAKE="$GNU_MAKE CROSS_COMPILE=${CROSS_COMPILE}"
-	else
-	    MAKE=$GNU_MAKE
-	fi
-
-	if [  "${output_dir}" != "." ] ; then
-		MAKE="${MAKE} O=${output_dir}"
-	fi
-
-	${MAKE} mrproper >/dev/null
-
-	echo "Building ${target} board..."
-	${MAKE} -s ${target}_defconfig >/dev/null
-
-	${MAKE} ${JOBS} ${CHECK} all \
-		>${LOG_DIR}/$target.MAKELOG 2> ${LOG_DIR}/$target.ERR
-
-	# Check for 'make' errors
-	if [ ${PIPESTATUS[0]} -ne 0 ] ; then
-		RC=1
-	fi
-
-	OBJS=${output_dir}/u-boot
-	if [ -e ${output_dir}/spl/u-boot-spl ]; then
-		OBJS="${OBJS} ${output_dir}/spl/u-boot-spl"
-	fi
-
-	${CROSS_COMPILE}size ${OBJS} | tee -a ${LOG_DIR}/$target.MAKELOG
-
-	if [ $BUILD_MANY == 1 ] ; then
-		trap - TERM
-
-		${MAKE} -s clean
-
-		if [ -s ${LOG_DIR}/${target}.ERR ] ; then
-			cp ${LOG_DIR}/${target}.ERR ${OUTPUT_PREFIX}/ERR/${target}
-		else
-			rm ${LOG_DIR}/${target}.ERR
-		fi
-	else
-		if [ -s ${LOG_DIR}/${target}.ERR ] ; then
-			if grep -iw error ${LOG_DIR}/${target}.ERR ; then
-				: $(( ERR_CNT += 1 ))
-				ERR_LIST="${ERR_LIST} $target"
-			else
-				: $(( WRN_CNT += 1 ))
-				WRN_LIST="${WRN_LIST} $target"
-			fi
-		else
-			rm ${LOG_DIR}/${target}.ERR
-		fi
-	fi
-
-	[ -e "${LOG_DIR}/${target}.ERR" ] && cat "${LOG_DIR}/${target}.ERR"
-
-	touch "${donep}${build_idx}"
-}
-
-manage_builds() {
-	search_idx=${OLDEST_IDX}
-	if [ "$ONLY_LIST" == 'y' ] ; then return ; fi
-
-	while true; do
-		if [ -e "${donep}${search_idx}" ] ; then
-			: $(( CURRENT_CNT-- ))
-			[ ${OLDEST_IDX} -eq ${search_idx} ] &&
-				: $(( OLDEST_IDX++ ))
-
-			# Only want to count it once
-			rm -f "${donep}${search_idx}"
-			touch "${skipp}${search_idx}"
-		elif [ -e "${skipp}${search_idx}" ] ; then
-			[ ${OLDEST_IDX} -eq ${search_idx} ] &&
-				: $(( OLDEST_IDX++ ))
-		fi
-		: $(( search_idx++ ))
-		if [ ${search_idx} -gt ${TOTAL_CNT} ] ; then
-			if [ ${CURRENT_CNT} -ge ${BUILD_NBUILDS} ] ; then
-				search_idx=${OLDEST_IDX}
-				sleep 1
-			else
-				break
-			fi
-		fi
-	done
-}
-
-build_targets() {
-	for t in "$@" ; do
-		# If a LIST_xxx var exists, use it.  But avoid variable
-		# expansion in the eval when a board name contains certain
-		# characters that the shell interprets.
-		case ${t} in
-			*[-+=]*) list= ;;
-			*)       list=$(eval echo '${LIST_'$t'}') ;;
-		esac
-		if [ -n "${list}" ] ; then
-			build_targets ${list}
-		else
-			: $((TOTAL_CNT += 1))
-			: $((CURRENT_CNT += 1))
-			rm -f "${donep}${TOTAL_CNT}"
-			rm -f "${skipp}${TOTAL_CNT}"
-			if [ "$CONTINUE" = 'y' -a -e ${LOG_DIR}/$t.MAKELOG ] ; then
-				: $((SKIP_CNT += 1))
-				touch "${donep}${TOTAL_CNT}"
-			elif [ "$REBUILD_ERRORS" = 'y' -a ! -e ${LOG_DIR}/$t.ERR ] ; then
-				: $((SKIP_CNT += 1))
-				touch "${donep}${TOTAL_CNT}"
-			else
-				if [ $BUILD_MANY == 1 ] ; then
-					build_target ${t} ${TOTAL_CNT} &
-				else
-					CUR_TGT="${t}"
-					build_target ${t} ${TOTAL_CNT}
-					CUR_TGT=''
-				fi
-			fi
-		fi
-
-		# We maintain a running count of all the builds we have done.
-		# Each finished build will have a file called ${donep}${n},
-		# where n is the index of the build. Each build
-		# we've already noted as finished will have ${skipp}${n}.
-		# We track the current index via TOTAL_CNT, and the oldest
-		# index. When we exceed the maximum number of parallel builds,
-		# We look from oldest to current for builds that have completed,
-		# and update the current count and oldest index as appropriate.
-		# If we've gone through the entire list, wait a second, and
-		# reprocess the entire list until we find a build that has
-		# completed
-		if [ ${CURRENT_CNT} -ge ${BUILD_NBUILDS} ] ; then
-			manage_builds
-		fi
-	done
-}
-
-#-----------------------------------------------------------------------
-
-kill_children() {
-	local OS=$(uname -s)
-	local children=""
-	case "${OS}" in
-		"Darwin")
-			# Mac OS X is known to have BSD style ps
-			local pgid=$(ps -p $$ -o pgid | sed -e "/PGID/d")
-			children=$(ps -g $pgid -o pid | sed -e "/PID\|$$\|$pgid/d")
-			;;
-		*)
-			# everything else tries the GNU style
-			local pgid=$(ps -p $$ --no-headers -o "%r" | tr -d ' ')
-			children=$(pgrep -g $pgid | sed -e "/$$\|$pgid/d")
-			;;
-	esac
-
-	kill $children 2> /dev/null
-	wait $children 2> /dev/null
-
-	exit
-}
-
-print_stats() {
-	if [ "$ONLY_LIST" == 'y' ] ; then return ; fi
-
-	# Only count boards that completed
-	: $((TOTAL_CNT = `find ${skipp}* 2> /dev/null | wc -l`))
-
-	rm -f ${donep}* ${skipp}*
-
-	if [ $BUILD_MANY == 1 ] && [ -e "${OUTPUT_PREFIX}/ERR" ] ; then
-		ERR_LIST=`grep -riwl error ${OUTPUT_PREFIX}/ERR/`
-		ERR_LIST=`for f in $ERR_LIST ; do echo -n " $(basename $f)" ; done`
-		ERR_CNT=`echo $ERR_LIST | wc -w | awk '{print $1}'`
-		WRN_LIST=`grep -riwL error ${OUTPUT_PREFIX}/ERR/`
-		WRN_LIST=`for f in $WRN_LIST ; do echo -n " $(basename $f)" ; done`
-		WRN_CNT=`echo $WRN_LIST | wc -w | awk '{print $1}'`
-	else
-		# Remove the logs for any board that was interrupted
-		rm -f ${LOG_DIR}/${CUR_TGT}.MAKELOG ${LOG_DIR}/${CUR_TGT}.ERR
-	fi
-
-	: $((TOTAL_CNT -= ${SKIP_CNT}))
-	echo ""
-	echo "--------------------- SUMMARY ----------------------------"
-	if [ "$CONTINUE" = 'y' -o "$REBUILD_ERRORS" = 'y' ] ; then
-		echo "Boards skipped: ${SKIP_CNT}"
-	fi
-	echo "Boards compiled: ${TOTAL_CNT}"
-	if [ ${ERR_CNT} -gt 0 ] ; then
-		echo "Boards with errors: ${ERR_CNT} (${ERR_LIST} )"
-	fi
-	if [ ${WRN_CNT} -gt 0 ] ; then
-		echo "Boards with warnings but no errors: ${WRN_CNT} (${WRN_LIST} )"
-	fi
-	echo "----------------------------------------------------------"
-
-	if [ $BUILD_MANY == 1 ] ; then
-		kill_children
-	fi
-
-	deprecation
-
-	exit $RC
-}
-
-#-----------------------------------------------------------------------
-
-# Build target groups selected by options, plus any command line args
-set -- ${SELECTED} "$@"
-# run PowerPC by default
-[ $# = 0 ] && set -- powerpc
-build_targets "$@"
-wait

Makefile

@@ -5,7 +5,7 @@
 VERSION = 2016
 PATCHLEVEL = 09
 SUBLEVEL =
-EXTRAVERSION = -rc1
+EXTRAVERSION = -rc2
 NAME =
 
 # *DOCUMENTATION*
@@ -425,7 +425,7 @@ timestamp_h := include/generated/timestamp_autogenerated.h
 
 no-dot-config-targets := clean clobber mrproper distclean \
 			 help %docs check% coccicheck \
-			 ubootversion backup
+			 ubootversion backup tests
 
 config-targets := 0
 mixed-targets  := 0
@@ -557,6 +557,14 @@ else
 include/config/auto.conf: ;
 endif # $(dot-config)
 
+#
+# Xtensa linker script cannot be preprocessed with -ansi because of
+# preprocessor operations on strings that don't make C identifiers.
+#
+ifeq ($(CONFIG_XTENSA),)
+LDPPFLAGS	+= -ansi
+endif
+
 ifdef CONFIG_CC_OPTIMIZE_FOR_SIZE
 KBUILD_CFLAGS	+= -Os
 else
@@ -638,6 +646,7 @@ libs-y += drivers/net/
 libs-y += drivers/net/phy/
 libs-y += drivers/pci/
 libs-y += drivers/power/ \
+	drivers/power/domain/ \
 	drivers/power/fuel_gauge/ \
 	drivers/power/mfd/ \
 	drivers/power/pmic/ \
@@ -666,6 +675,7 @@ libs-$(CONFIG_HAS_POST) += post/
 libs-y += test/
 libs-y += test/dm/
 libs-$(CONFIG_UT_ENV) += test/env/
+libs-$(CONFIG_UT_OVERLAY) += test/overlay/
 
 libs-y += $(if $(BOARDDIR),board/$(BOARDDIR)/)
 
@@ -1311,7 +1321,7 @@ $(timestamp_h): $(srctree)/Makefile FORCE
 
 # ---------------------------------------------------------------------------
 quiet_cmd_cpp_lds = LDS     $@
-cmd_cpp_lds = $(CPP) -Wp,-MD,$(depfile) $(cpp_flags) $(LDPPFLAGS) -ansi \
+cmd_cpp_lds = $(CPP) -Wp,-MD,$(depfile) $(cpp_flags) $(LDPPFLAGS) \
 		-D__ASSEMBLY__ -x assembler-with-cpp -P -o $@ $<
 
 u-boot.lds: $(LDSCRIPT) prepare FORCE
@@ -1417,7 +1427,7 @@ CLEAN_FILES += include/bmp_logo.h include/bmp_logo_data.h include/license.h \
 MRPROPER_DIRS  += include/config include/generated spl tpl \
 		  .tmp_objdiff
 MRPROPER_FILES += .config .config.old include/autoconf.mk* include/config.h \
-		  ctags etags TAGS cscope* GPATH GTAGS GRTAGS GSYMS
+		  ctags etags tags TAGS cscope* GPATH GTAGS GRTAGS GSYMS
 
 # clean - Delete most, but leave enough to build external modules
 #
@@ -1488,6 +1498,7 @@ help:
 	@echo  ''
 	@echo  'Other generic targets:'
 	@echo  '  all		  - Build all necessary images depending on configuration'
+	@echo  '  tests		  - Build U-Boot for sandbox and run tests'
 	@echo  '* u-boot	  - Build the bare u-boot'
 	@echo  '  dir/            - Build all files in dir and below'
 	@echo  '  dir/file.[oisS] - Build specified target only'
@@ -1520,6 +1531,8 @@ help:
 	@echo  'Execute "make" or "make all" to build all targets marked with [*] '
 	@echo  'For further info see the ./README file'
 
+tests:
+	$(srctree)/test/run
 
 # Documentation targets
 # ---------------------------------------------------------------------------

README

@@ -840,6 +840,9 @@ The following options need to be configured:
 			CONFIG_CONSOLE_EXTRA_INFO
 						additional board info beside
 						the logo
+			CONFIG_HIDE_LOGO_VERSION
+						do not display bootloader
+						version string
 
 		When CONFIG_CFB_CONSOLE_ANSI is defined, console will support
 		a limited number of ANSI escape sequences (cursor control,
@@ -2753,7 +2756,7 @@ CBFS (Coreboot Filesystem) support
 		with a special header) as build targets. By defining
 		CONFIG_BUILD_TARGET in the SoC / board header, this
 		special image will be automatically built upon calling
-		make / MAKEALL.
+		make / buildman.
 
 		CONFIG_IDENT_STRING
 
@@ -5080,33 +5083,10 @@ official or latest in the git repository) version of U-Boot sources.
 But before you submit such a patch, please verify that your modifi-
 cation did not break existing code. At least make sure that *ALL* of
 the supported boards compile WITHOUT ANY compiler warnings. To do so,
-just run the "MAKEALL" script, which will configure and build U-Boot
-for ALL supported system. Be warned, this will take a while. You can
-select which (cross) compiler to use by passing a `CROSS_COMPILE'
-environment variable to the script, i. e. to use the ELDK cross tools
-you can type
-
-	CROSS_COMPILE=ppc_8xx- MAKEALL
-
-or to build on a native PowerPC system you can type
-
-	CROSS_COMPILE=' ' MAKEALL
-
-When using the MAKEALL script, the default behaviour is to build
-U-Boot in the source directory. This location can be changed by
-setting the BUILD_DIR environment variable. Also, for each target
-built, the MAKEALL script saves two log files (<target>.ERR and
-<target>.MAKEALL) in the <source dir>/LOG directory. This default
-location can be changed by setting the MAKEALL_LOGDIR environment
-variable. For example:
-
-	export BUILD_DIR=/tmp/build
-	export MAKEALL_LOGDIR=/tmp/log
-	CROSS_COMPILE=ppc_8xx- MAKEALL
-
-With the above settings build objects are saved in the /tmp/build,
-log files are saved in the /tmp/log and the source tree remains clean
-during the whole build process.
+just run the buildman script (tools/buildman/buildman), which will
+configure and build U-Boot for ALL supported system. Be warned, this
+will take a while. Please see the buildman README, or run 'buildman -H'
+for documentation.
 
 
 See also "U-Boot Porting Guide" below.
@@ -6562,7 +6542,7 @@ it:
 
 Notes:
 
-* Before sending the patch, run the MAKEALL script on your patched
+* Before sending the patch, run the buildman script on your patched
   source tree and make sure that no errors or warnings are reported
   for any of the boards.
 

arch/Kconfig

@@ -88,6 +88,11 @@ config X86
 	select DM_SPI
 	select DM_SPI_FLASH
 
+config XTENSA
+	bool "Xtensa architecture"
+	select CREATE_ARCH_SYMLINK
+	select SUPPORT_OF_CONTROL
+
 endchoice
 
 config SYS_ARCH
@@ -161,3 +166,4 @@ source "arch/sandbox/Kconfig"
 source "arch/sh/Kconfig"
 source "arch/sparc/Kconfig"
 source "arch/x86/Kconfig"
+source "arch/xtensa/Kconfig"

arch/arc/Kconfig

@@ -118,21 +118,21 @@ config SYS_DCACHE_OFF
 
 choice
 	prompt "Target select"
-	default TARGET_AXS101
+	default TARGET_AXS10X
 
 config TARGET_TB100
 	bool "Support tb100"
 
-config TARGET_ARCANGEL4
-	bool "Support arcangel4"
+config TARGET_NSIM
+	bool "Support standalone nSIM & Free nSIM"
 
-config TARGET_AXS101
-	bool "Support axs101"
+config TARGET_AXS10X
+	bool "Support Synopsys Designware SDP board (AXS101 & AXS103)"
 
 endchoice
 
 source "board/abilis/tb100/Kconfig"
 source "board/synopsys/Kconfig"
-source "board/synopsys/axs101/Kconfig"
+source "board/synopsys/axs10x/Kconfig"
 
 endmenu

arch/arc/cpu/arcv2/ivt.S

@@ -7,21 +7,26 @@
 .section .ivt, "a",@progbits
 .align 4
 	/* Critical system events */
-.word	_start			/* 0 - 0x000 */
-.word	memory_error		/* 1 - 0x008 */
-.word	instruction_error	/* 2 - 0x010 */
+.word	_start			/* 0x00 - Reset */
+.word	memory_error		/* 0x01 - Memory Error */
+.word	instruction_error	/* 0x02 - Instruction Error */
 
 	/* Exceptions */
-.word	EV_MachineCheck		/* 0x100, Fatal Machine check  (0x20) */
-.word	EV_TLBMissI		/* 0x108, Intruction TLB miss  (0x21) */
-.word	EV_TLBMissD		/* 0x110, Data TLB miss        (0x22) */
-.word	EV_TLBProtV		/* 0x118, Protection Violation (0x23)
-							or Misaligned Access  */
-.word	EV_PrivilegeV		/* 0x120, Privilege Violation  (0x24) */
-.word	EV_Trap			/* 0x128, Trap exception       (0x25) */
-.word	EV_Extension		/* 0x130, Extn Intruction Excp (0x26) */
+.word	EV_MachineCheck		/* 0x03 - Fatal Machine check */
+.word	EV_TLBMissI		/* 0x04 - Intruction TLB miss */
+.word	EV_TLBMissD		/* 0x05 - Data TLB miss */
+.word	EV_TLBProtV		/* 0x06 - Protection Violation or Misaligned Access */
+.word	EV_PrivilegeV		/* 0x07 - Privilege Violation */
+.word	EV_SWI			/* 0x08 - Software Interrupt */
+.word	EV_Trap			/* 0x09 - Trap */
+.word	EV_Extension		/* 0x0A - Extension Intruction Exception */
+.word	EV_DivZero		/* 0x0B - Division by Zero */
+.word	EV_DCError		/* 0x0C - Data cache consistency error */
+.word	EV_Maligned		/* 0x0D - Misaligned data access */
+.word	0			/* 0x0E - Unused */
+.word	0			/* 0x0F - Unused */
 
 	/* Device interrupts */
-.rept	29
-	j	interrupt_handler	/* 3:31 - 0x018:0xF8 */
+.rept	240
+.word	interrupt_handler	/* 0x10 - 0xFF */
 .endr

arch/arc/cpu/u-boot.lds

@@ -4,38 +4,29 @@
  * SPDX-License-Identifier:	GPL-2.0+
  */
 
+#include <config.h>
+
 OUTPUT_FORMAT("elf32-littlearc", "elf32-littlearc", "elf32-littlearc")
 OUTPUT_ARCH(arc)
 ENTRY(_start)
 SECTIONS
 {
-	. = ALIGN(4);
+	. = CONFIG_SYS_TEXT_BASE;
+	__image_copy_start = .;
+	__text_start = .;
 	.text :	{
-		*(.__text_start)
-		*(.__image_copy_start)
 		arch/arc/lib/start.o (.text*)
 		*(.text*)
 	}
-
-	. = ALIGN(4);
-	.text_end :
-	{
-		*(.__text_end)
-	}
+	__text_end = .;
 
 	. = ALIGN(1024);
-	.ivt_start : {
-		*(.__ivt_start)
-	}
-
+	__ivt_start = .;
 	.ivt :
 	{
 		*(.ivt)
 	}
-
-	.ivt_end : {
-		*(.__ivt_end)
-	}
+	__ivt_end = .;
 
 	. = ALIGN(4);
 	.rodata : {
@@ -53,34 +44,20 @@ SECTIONS
 	}
 
 	. = ALIGN(4);
-	.rel_dyn_start : {
-		*(.__rel_dyn_start)
-	}
-
+	__rel_dyn_start = .;
 	.rela.dyn : {
 		*(.rela.dyn)
 	}
-
-	.rel_dyn_end : {
-		*(.__rel_dyn_end)
-	}
+	__rel_dyn_end = .;
 
 	. = ALIGN(4);
-	.bss_start : {
-		*(.__bss_start);
-	}
-
+	__bss_start = .;
 	.bss : {
 		*(.bss*)
 	}
-
-	.bss_end : {
-		*(.__bss_end);
-	}
+	__bss_end = .;
 
 	. = ALIGN(4);
-	.image_copy_end : {
-		*(.__image_copy_end)
-		*(.__init_end)
-	}
+	__image_copy_end = .;
+	__init_end = .;
 }

arch/arc/dts/Makefile

@@ -2,8 +2,8 @@
 # SPDX-License-Identifier:	GPL-2.0+
 #
 
-dtb-$(CONFIG_TARGET_AXS101) +=  axs10x.dtb
-dtb-$(CONFIG_TARGET_ARCANGEL4) +=  arcangel4.dtb
+dtb-$(CONFIG_TARGET_AXS10X) +=  axs10x.dtb
+dtb-$(CONFIG_TARGET_NSIM) +=  nsim.dtb
 dtb-$(CONFIG_TARGET_TB100) +=  abilis_tb100.dtb
 
 targets += $(dtb-y)

arch/arc/dts/nsim.dts

@@ -1,5 +1,5 @@
 /*
- * Copyright (C) 2015 Synopsys, Inc. (www.synopsys.com)
+ * Copyright (C) 2015-2016 Synopsys, Inc. (www.synopsys.com)
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

arch/arc/include/asm/sections.h

@@ -9,9 +9,7 @@
 
 #include <asm-generic/sections.h>
 
-extern ulong __text_end;
 extern ulong __ivt_start;
 extern ulong __ivt_end;
-extern ulong __image_copy_start;
 
 #endif /* __ASM_ARC_SECTIONS_H */

arch/arc/lib/Makefile

@@ -9,7 +9,6 @@ head-y := start.o
 obj-y += cache.o
 obj-y += cpu.o
 obj-y += interrupts.o
-obj-y += sections.o
 obj-y += relocate.o
 obj-y += strchr-700.o
 obj-y += strcmp.o

arch/arc/lib/interrupts.c

@@ -141,3 +141,29 @@ void do_extension(struct pt_regs *regs)
 	printf("Extension instruction exception\n");
 	bad_mode(regs);
 }
+
+#ifdef CONFIG_ISA_ARCV2
+void do_swi(struct pt_regs *regs)
+{
+	printf("Software Interrupt exception\n");
+	bad_mode(regs);
+}
+
+void do_divzero(unsigned long address, struct pt_regs *regs)
+{
+	printf("Division by zero exception @ 0x%lx\n", address);
+	bad_mode(regs);
+}
+
+void do_dcerror(struct pt_regs *regs)
+{
+	printf("Data cache consistency error exception\n");
+	bad_mode(regs);
+}
+
+void do_maligned(unsigned long address, struct pt_regs *regs)
+{
+	printf("Misaligned data access exception @ 0x%lx\n", address);
+	bad_mode(regs);
+}
+#endif

arch/arc/lib/ints_low.S

@@ -149,3 +149,31 @@ ENTRY(EV_Extension)
 	mov	%r0, %sp
 	j	do_extension
 ENDPROC(EV_Extension)
+
+#ifdef CONFIG_ISA_ARCV2
+ENTRY(EV_SWI)
+	SAVE_ALL_SYS
+	mov	%r0, %sp
+	j	do_swi
+ENDPROC(EV_SWI)
+
+ENTRY(EV_DivZero)
+	SAVE_ALL_SYS
+	SAVE_EXCEPTION_SOURCE
+	mov	%r1, %sp
+	j	do_divzero
+ENDPROC(EV_DivZero)
+
+ENTRY(EV_DCError)
+	SAVE_ALL_SYS
+	mov	%r0, %sp
+	j	do_dcerror
+ENDPROC(EV_DCError)
+
+ENTRY(EV_Maligned)
+	SAVE_ALL_SYS
+	SAVE_EXCEPTION_SOURCE
+	mov	%r1, %sp
+	j	do_maligned
+ENDPROC(EV_Maligned)
+#endif

arch/arc/lib/relocate.c

@@ -6,7 +6,10 @@
 
 #include <common.h>
 #include <elf.h>
-#include <asm/sections.h>
+#include <asm-generic/sections.h>
+
+extern ulong __image_copy_start;
+extern ulong __ivt_end;
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -37,6 +40,9 @@ int do_elf_reloc_fixups(void)
 	Elf32_Rela *re_src = (Elf32_Rela *)(&__rel_dyn_start);
 	Elf32_Rela *re_end = (Elf32_Rela *)(&__rel_dyn_end);
 
+	debug("Section .rela.dyn is located at %08x-%08x\n",
+	      (unsigned int)re_src, (unsigned int)re_end);
+
 	Elf32_Addr *offset_ptr_rom, *last_offset = NULL;
 	Elf32_Addr *offset_ptr_ram;
 
@@ -52,6 +58,10 @@ int do_elf_reloc_fixups(void)
 			offset_ptr_ram = (Elf32_Addr *)((ulong)offset_ptr_rom +
 							gd->reloc_off);
 
+			debug("Patching value @ %08x (relocated to %08x)\n",
+			      (unsigned int)offset_ptr_rom,
+			      (unsigned int)offset_ptr_ram);
+
 			/*
 			 * Use "memcpy" because target location might be
 			 * 16-bit aligned on ARC so we may need to read

arch/arc/lib/sections.c

@@ -1,23 +0,0 @@
-/*
- * Copyright (C) 2013-2014 Synopsys, Inc. All rights reserved.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * For some reason linker sets linker-generated symbols to zero in PIE mode.
- * A work-around is substitution of linker-generated symbols with
- * compiler-generated symbols which are properly handled by linker in PAE mode.
- */
-
-char __bss_start[0] __attribute__((section(".__bss_start")));
-char __bss_end[0] __attribute__((section(".__bss_end")));
-char __image_copy_start[0] __attribute__((section(".__image_copy_start")));
-char __image_copy_end[0] __attribute__((section(".__image_copy_end")));
-char __rel_dyn_start[0] __attribute__((section(".__rel_dyn_start")));
-char __rel_dyn_end[0] __attribute__((section(".__rel_dyn_end")));
-char __text_start[0] __attribute__((section(".__text_start")));
-char __text_end[0] __attribute__((section(".__text_end")));
-char __init_end[0] __attribute__((section(".__init_end")));
-char __ivt_start[0] __attribute__((section(".__ivt_start")));
-char __ivt_end[0] __attribute__((section(".__ivt_end")));

arch/arm/Kconfig

@@ -6,6 +6,7 @@ config SYS_ARCH
 
 config ARM64
 	bool
+	select PHYS_64BIT
 
 config DMA_ADDR_T_64BIT
 	bool
@@ -553,11 +554,14 @@ config TARGET_MX53SMD
 config OMAP34XX
 	bool "OMAP34XX SoC"
 	select CPU_V7
+	select SUPPORT_SPL
+	select USE_TINY_PRINTF
 
 config OMAP44XX
 	bool "OMAP44XX SoC"
 	select CPU_V7
 	select SUPPORT_SPL
+	select USE_TINY_PRINTF
 
 config OMAP54XX
 	bool "OMAP54XX SoC"
@@ -575,9 +579,10 @@ config AM43XX
 	  protocols, dual camera support, optional 3D graphics
 	  and an optional customer programmable secure boot.
 
-config RMOBILE
+config ARCH_RMOBILE
 	bool "Renesas ARM SoCs"
-	select CPU_V7
+	select DM
+	select DM_SERIAL
 
 config TARGET_S32V234EVB
 	bool "Support s32v234evb"
@@ -657,10 +662,13 @@ config ARCH_ZYNQ
 	select DM_GPIO
 	select SPL_DM if SPL
 	select DM_MMC
+	select DM_MMC_OPS
 	select DM_SPI
 	select DM_SERIAL
 	select DM_SPI_FLASH
 	select SPL_SEPARATE_BSS if SPL
+	select DM_USB if USB
+	select BLK
 
 config ARCH_ZYNQMP
 	bool "Support Xilinx ZynqMP Platform"
@@ -671,6 +679,7 @@ config ARCH_ZYNQMP
 	select SUPPORT_SPL
 	select CLK
 	select SPL_CLK
+	select DM_USB if USB
 
 config TEGRA
 	bool "NVIDIA Tegra"
@@ -840,15 +849,12 @@ config STM32
 
 config ARCH_ROCKCHIP
 	bool "Support Rockchip SoCs"
-	select SUPPORT_SPL
-	select SPL
 	select OF_CONTROL
-	select CPU_V7
 	select BLK
 	select DM
-	select SPL_DM
+	select SPL_DM if SPL
 	select SYS_MALLOC_F
-	select SPL_SYS_MALLOC_SIMPLE
+	select SPL_SYS_MALLOC_SIMPLE if SPL
 	select DM_GPIO
 	select DM_I2C
 	select DM_MMC
@@ -892,7 +898,7 @@ source "arch/arm/cpu/armv7/omap-common/Kconfig"
 
 source "arch/arm/mach-orion5x/Kconfig"
 
-source "arch/arm/cpu/armv7/rmobile/Kconfig"
+source "arch/arm/mach-rmobile/Kconfig"
 
 source "arch/arm/mach-meson/Kconfig"
 

arch/arm/Makefile

@@ -20,6 +20,14 @@ arch-$(CONFIG_CPU_V7)		=$(call cc-option, -march=armv7-a, \
 				 $(call cc-option, -march=armv7, -march=armv5))
 arch-$(CONFIG_ARM64)		=-march=armv8-a
 
+# On Tegra systems we must build SPL for the armv4 core on the device
+# but otherwise we can use the value in CONFIG_SYS_ARM_ARCH
+ifeq ($(CONFIG_SPL_BUILD)$(CONFIG_TEGRA),yy)
+arch-y += -D__LINUX_ARM_ARCH__=4
+else
+arch-y += -D__LINUX_ARM_ARCH__=$(CONFIG_SYS_ARM_ARCH)
+endif
+
 # Evaluate arch cc-option calls now
 arch-y := $(arch-y)
 
@@ -59,6 +67,7 @@ machine-$(CONFIG_ARCH_S5PC1XX)		+= s5pc1xx
 machine-$(CONFIG_ARCH_SUNXI)		+= sunxi
 machine-$(CONFIG_ARCH_SNAPDRAGON)	+= snapdragon
 machine-$(CONFIG_ARCH_SOCFPGA)		+= socfpga
+machine-$(CONFIG_ARCH_RMOBILE)		+= rmobile
 machine-$(CONFIG_ARCH_ROCKCHIP)		+= rockchip
 machine-$(CONFIG_STM32)			+= stm32
 machine-$(CONFIG_TEGRA)			+= tegra

arch/arm/cpu/armv7/Kconfig

@@ -7,14 +7,14 @@ config CPU_V7_HAS_VIRT
         bool
 
 config ARMV7_NONSEC
-	boolean "Enable support for booting in non-secure mode" if EXPERT
+	bool "Enable support for booting in non-secure mode" if EXPERT
 	depends on CPU_V7_HAS_NONSEC
 	default y
 	---help---
 	Say Y here to enable support for booting in non-secure / SVC mode.
 
 config ARMV7_BOOT_SEC_DEFAULT
-	boolean "Boot in secure mode by default" if EXPERT
+	bool "Boot in secure mode by default" if EXPERT
 	depends on ARMV7_NONSEC
 	default y if TEGRA
 	---help---
@@ -25,14 +25,14 @@ config ARMV7_BOOT_SEC_DEFAULT
 	variable to "sec" or "nonsec".
 
 config ARMV7_VIRT
-	boolean "Enable support for hardware virtualization" if EXPERT
+	bool "Enable support for hardware virtualization" if EXPERT
 	depends on CPU_V7_HAS_VIRT && ARMV7_NONSEC
 	default y
 	---help---
 	Say Y here to boot in hypervisor (HYP) mode when booting non-secure.
 
 config ARMV7_LPAE
-	boolean "Use LPAE page table format" if EXPERT
+	bool "Use LPAE page table format" if EXPERT
 	depends on CPU_V7
 	default n
 	---help---

arch/arm/cpu/armv7/cache_v7.c

@@ -75,7 +75,7 @@ static void v7_dcache_maint_range(u32 start, u32 stop, u32 range_op)
 	}
 
 	/* DSB to make sure the operation is complete */
-	DSB;
+	dsb();
 }
 
 /* Invalidate TLB */
@@ -88,9 +88,9 @@ static void v7_inval_tlb(void)
 	/* Invalidate entire instruction TLB */
 	asm volatile ("mcr p15, 0, %0, c8, c5, 0" : : "r" (0));
 	/* Full system DSB - make sure that the invalidation is complete */
-	DSB;
+	dsb();
 	/* Full system ISB - make sure the instruction stream sees it */
-	ISB;
+	isb();
 }
 
 void invalidate_dcache_all(void)
@@ -194,10 +194,10 @@ void invalidate_icache_all(void)
 	asm volatile ("mcr p15, 0, %0, c7, c5, 6" : : "r" (0));
 
 	/* Full system DSB - make sure that the invalidation is complete */
-	DSB;
+	dsb();
 
 	/* ISB - make sure the instruction stream sees it */
-	ISB;
+	isb();
 }
 #else
 void invalidate_icache_all(void)

arch/arm/cpu/armv7/ls102xa/psci.S

@@ -12,19 +12,102 @@
 #include <asm/arch-armv7/generictimer.h>
 #include <asm/psci.h>
 
+#define RCPM_TWAITSR		0x04C
+
 #define SCFG_CORE0_SFT_RST      0x130
 #define SCFG_CORESRENCR         0x204
 
-#define DCFG_CCSR_BRR           0x0E4
-#define DCFG_CCSR_SCRATCHRW1    0x200
+#define DCFG_CCSR_RSTCR			0x0B0
+#define DCFG_CCSR_RSTCR_RESET_REQ	0x2
+#define DCFG_CCSR_BRR			0x0E4
+#define DCFG_CCSR_SCRATCHRW1		0x200
+
+#define PSCI_FN_PSCI_VERSION_FEATURE_MASK	0x0
+#define PSCI_FN_CPU_SUSPEND_FEATURE_MASK	0x0
+#define PSCI_FN_CPU_OFF_FEATURE_MASK		0x0
+#define PSCI_FN_CPU_ON_FEATURE_MASK		0x0
+#define PSCI_FN_AFFINITY_INFO_FEATURE_MASK	0x0
+#define PSCI_FN_SYSTEM_OFF_FEATURE_MASK		0x0
+#define PSCI_FN_SYSTEM_RESET_FEATURE_MASK	0x0
 
 	.pushsection ._secure.text, "ax"
 
 	.arch_extension sec
 
+	.align	5
+
 #define	ONE_MS		(GENERIC_TIMER_CLK / 1000)
 #define	RESET_WAIT	(30 * ONE_MS)
 
+.globl	psci_version
+psci_version:
+	movw	r0, #0
+	movt	r0, #1
+
+	bx	lr
+
+_ls102x_psci_supported_table:
+	.word	ARM_PSCI_0_2_FN_PSCI_VERSION
+	.word	PSCI_FN_PSCI_VERSION_FEATURE_MASK
+	.word	ARM_PSCI_0_2_FN_CPU_SUSPEND
+	.word	PSCI_FN_CPU_SUSPEND_FEATURE_MASK
+	.word	ARM_PSCI_0_2_FN_CPU_OFF
+	.word	PSCI_FN_CPU_OFF_FEATURE_MASK
+	.word	ARM_PSCI_0_2_FN_CPU_ON
+	.word	PSCI_FN_CPU_ON_FEATURE_MASK
+	.word	ARM_PSCI_0_2_FN_AFFINITY_INFO
+	.word	PSCI_FN_AFFINITY_INFO_FEATURE_MASK
+	.word	ARM_PSCI_0_2_FN_SYSTEM_OFF
+	.word	PSCI_FN_SYSTEM_OFF_FEATURE_MASK
+	.word	ARM_PSCI_0_2_FN_SYSTEM_RESET
+	.word	PSCI_FN_SYSTEM_RESET_FEATURE_MASK
+	.word	0
+	.word	ARM_PSCI_RET_NI
+
+.globl	psci_features
+psci_features:
+	adr	r2, _ls102x_psci_supported_table
+1:	ldr	r3, [r2]
+	cmp	r3, #0
+	beq	out_psci_features
+	cmp	r1, r3
+	addne	r2, r2, #8
+	bne	1b
+
+out_psci_features:
+	ldr	r0, [r2, #4]
+	bx	lr
+
+@ r0: return value ARM_PSCI_RET_SUCCESS or ARM_PSCI_RET_INVAL
+@ r1: input target CPU ID in MPIDR format, original value in r1 may be dropped
+@ r4: output validated CPU ID if ARM_PSCI_RET_SUCCESS returns, meaningless for
+@ ARM_PSCI_RET_INVAL,suppose caller saves r4 before calling
+LENTRY(psci_check_target_cpu_id)
+	@ Get the real CPU number
+	and	r4, r1, #0xff
+	mov	r0, #ARM_PSCI_RET_INVAL
+
+	@ Bit[31:24], bits must be zero.
+	tst	r1, #0xff000000
+	bxne	lr
+
+	@ Affinity level 2 - Cluster: only one cluster in LS1021xa.
+	tst	r1, #0xff0000
+	bxne	lr
+
+	@ Affinity level 1 - Processors: should be in 0xf00 format.
+	lsr	r1, r1, #8
+	teq	r1, #0xf
+	bxne	lr
+
+	@ Affinity level 0 - CPU: only 0, 1 are valid in LS1021xa.
+	cmp	r4, #2
+	bxge	lr
+
+	mov	r0, #ARM_PSCI_RET_SUCCESS
+	bx	lr
+ENDPROC(psci_check_target_cpu_id)
+
 	@ r1 = target CPU
 	@ r2 = target PC
 .globl	psci_cpu_on
@@ -33,7 +116,9 @@ psci_cpu_on:
 
 	@ Clear and Get the correct CPU number
 	@ r1 = 0xf01
-	and	r4, r1, #0xff
+	bl	psci_check_target_cpu_id
+	cmp	r0, #ARM_PSCI_RET_INVAL
+	beq	out_psci_cpu_on
 
 	mov	r0, r4
 	mov	r1, r2
@@ -101,6 +186,7 @@ holdoff_release:
 	@ Return
 	mov	r0, #ARM_PSCI_RET_SUCCESS
 
+out_psci_cpu_on:
 	pop	{r4, r5, r6, lr}
 	bx	lr
 
@@ -108,6 +194,52 @@ holdoff_release:
 psci_cpu_off:
 	bl	psci_cpu_off_common
 
+1:	wfi
+	b	1b
+
+.globl	psci_affinity_info
+psci_affinity_info:
+	push	{lr}
+
+	mov	r0, #ARM_PSCI_RET_INVAL
+
+	@ Verify Affinity level
+	cmp	r2, #0
+	bne	out_affinity_info
+
+	bl	psci_check_target_cpu_id
+	cmp	r0, #ARM_PSCI_RET_INVAL
+	beq	out_affinity_info
+	mov	r1, r4
+
+	@ Get RCPM base address
+	movw	r4, #(CONFIG_SYS_FSL_RCPM_ADDR & 0xffff)
+	movt	r4, #(CONFIG_SYS_FSL_RCPM_ADDR >> 16)
+
+	mov	r0, #PSCI_AFFINITY_LEVEL_ON
+
+	@ Detect target CPU state
+	ldr	r2, [r4, #RCPM_TWAITSR]
+	rev	r2, r2
+	lsr	r2, r2, r1
+	ands	r2, r2, #1
+	beq	out_affinity_info
+
+	mov	r0, #PSCI_AFFINITY_LEVEL_OFF
+
+out_affinity_info:
+	pop	{pc}
+
+.globl	psci_system_reset
+psci_system_reset:
+	@ Get DCFG base address
+	movw	r1, #(CONFIG_SYS_FSL_GUTS_ADDR & 0xffff)
+	movt	r1, #(CONFIG_SYS_FSL_GUTS_ADDR >> 16)
+
+	mov	r2, #DCFG_CCSR_RSTCR_RESET_REQ
+	rev	r2, r2
+	str	r2, [r1, #DCFG_CCSR_RSTCR]
+
 1:	wfi
 	b	1b
 

arch/arm/cpu/armv7/mx6/Kconfig

@@ -148,6 +148,10 @@ config TARGET_PLATINUM_TITANIUM
 	bool "platinum-titanium"
 	select SUPPORT_SPL
 
+config TARGET_PCM058
+	bool "Phytec PCM058 i.MX6 Quad"
+	select SUPPORT_SPL
+
 config TARGET_SECOMX6
 	bool "secomx6 boards"
 
@@ -178,6 +182,18 @@ config TARGET_XPRESS
 	select DM_THERMAL
 	select SUPPORT_SPL
 
+config TARGET_ZC5202
+	bool "zc5202"
+	select SUPPORT_SPL
+	select DM
+	select DM_THERMAL
+
+config TARGET_ZC5601
+	bool "zc5601"
+	select SUPPORT_SPL
+	select DM
+	select DM_THERMAL
+
 endchoice
 
 config SYS_SOC
@@ -192,6 +208,7 @@ source "board/boundary/nitrogen6x/Kconfig"
 source "board/ccv/xpress/Kconfig"
 source "board/compulab/cm_fx6/Kconfig"
 source "board/congatec/cgtqmx6eval/Kconfig"
+source "board/el/el6x/Kconfig"
 source "board/embest/mx6boards/Kconfig"
 source "board/freescale/mx6qarm2/Kconfig"
 source "board/freescale/mx6qsabreauto/Kconfig"
@@ -200,6 +217,7 @@ source "board/freescale/mx6slevk/Kconfig"
 source "board/freescale/mx6sxsabresd/Kconfig"
 source "board/freescale/mx6sxsabreauto/Kconfig"
 source "board/freescale/mx6ul_14x14_evk/Kconfig"
+source "board/phytec/pcm058/Kconfig"
 source "board/gateworks/gw_ventana/Kconfig"
 source "board/kosagi/novena/Kconfig"
 source "board/seco/Kconfig"

arch/arm/cpu/armv7/mx6/clock.c

@@ -281,7 +281,7 @@ static u32 mxc_get_pll_pfd(enum pll_clocks pll, int pfd_num)
 	case PLL_BUS:
 		if (!is_mx6ul()) {
 			if (pfd_num == 3) {
-				/* No PFD3 on PPL2 */
+				/* No PFD3 on PLL2 */
 				return 0;
 			}
 		}
@@ -433,9 +433,9 @@ static u32 get_axi_clk(void)
 
 	if (cbcdr & MXC_CCM_CBCDR_AXI_SEL) {
 		if (cbcdr & MXC_CCM_CBCDR_AXI_ALT_SEL)
-			root_freq = mxc_get_pll_pfd(PLL_BUS, 2);
-		else
 			root_freq = mxc_get_pll_pfd(PLL_USBOTG, 1);
+		else
+			root_freq = mxc_get_pll_pfd(PLL_BUS, 2);
 	} else
 		root_freq = get_periph_clk();
 

arch/arm/cpu/armv7/mx7/Kconfig

@@ -3,6 +3,8 @@ if ARCH_MX7
 config MX7
 	bool
 	select ROM_UNIFIED_SECTIONS
+	select CPU_V7_HAS_VIRT
+	select CPU_V7_HAS_NONSEC
 	default y
 
 config MX7D
@@ -25,12 +27,19 @@ config TARGET_WARP7
 	select DM
 	select DM_THERMAL
 
+config TARGET_COLIBRI_IMX7
+	bool "Support Colibri iMX7S/iMX7D modules"
+	select DM
+	select DM_SERIAL
+	select DM_THERMAL
+
 endchoice
 
 config SYS_SOC
 	default "mx7"
 
 source "board/freescale/mx7dsabresd/Kconfig"
+source "board/toradex/colibri_imx7/Kconfig"
 source "board/warp7/Kconfig"
 
 endif

arch/arm/cpu/armv7/mx7/soc.c

@@ -248,6 +248,20 @@ int arch_cpu_init(void)
 	return 0;
 }
 
+#ifdef CONFIG_ARCH_MISC_INIT
+int arch_misc_init(void)
+{
+#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+	if (is_mx7d())
+		setenv("soc", "imx7d");
+	else
+		setenv("soc", "imx7s");
+#endif
+
+	return 0;
+}
+#endif
+
 #ifdef CONFIG_SERIAL_TAG
 void get_board_serial(struct tag_serialnr *serialnr)
 {

arch/arm/cpu/armv7/omap-common/clocks-common.c

@@ -443,15 +443,12 @@ void do_scale_vcore(u32 vcore_reg, u32 volt_mv, struct pmic_data *pmic)
 {
 	u32 offset_code;
 	u32 offset = volt_mv;
-#ifndef	CONFIG_DRA7XX
 	int ret = 0;
-#endif
 
 	if (!volt_mv)
 		return;
 
 	pmic->pmic_bus_init();
-#ifndef	CONFIG_DRA7XX
 	/* See if we can first get the GPIO if needed */
 	if (pmic->gpio_en)
 		ret = gpio_request(pmic->gpio, "PMIC_GPIO");
@@ -465,7 +462,7 @@ void do_scale_vcore(u32 vcore_reg, u32 volt_mv, struct pmic_data *pmic)
 	/* Pull the GPIO low to select SET0 register, while we program SET1 */
 	if (pmic->gpio_en)
 		gpio_direction_output(pmic->gpio, 0);
-#endif
+
 	/* convert to uV for better accuracy in the calculations */
 	offset *= 1000;
 
@@ -476,10 +473,8 @@ void do_scale_vcore(u32 vcore_reg, u32 volt_mv, struct pmic_data *pmic)
 
 	if (pmic->pmic_write(pmic->i2c_slave_addr, vcore_reg, offset_code))
 		printf("Scaling voltage failed for 0x%x\n", vcore_reg);
-#ifndef	CONFIG_DRA7XX
 	if (pmic->gpio_en)
 		gpio_direction_output(pmic->gpio, 1);
-#endif
 }
 
 static u32 optimize_vcore_voltage(struct volts const *v)
@@ -534,7 +529,6 @@ void __weak recalibrate_iodelay(void)
  */
 void scale_vcores(struct vcores_data const *vcores)
 {
-#if defined(CONFIG_DRA7XX)
 	int i;
 	struct volts *pv = (struct volts *)vcores;
 	struct volts *px;
@@ -594,7 +588,16 @@ void scale_vcores(struct vcores_data const *vcores)
 		  vcores->mpu.abb_tx_done_mask,
 		  OMAP_ABB_FAST_OPP);
 
-	/* The .mm member is not used for the DRA7xx */
+	debug("mm: %d\n", vcores->mm.value);
+	do_scale_vcore(vcores->mm.addr, vcores->mm.value, vcores->mm.pmic);
+	/* Configure MM ABB LDO after scale */
+	abb_setup(vcores->mm.efuse.reg,
+		  (*ctrl)->control_wkup_ldovbb_mm_voltage_ctrl,
+		  (*prcm)->prm_abbldo_mm_setup,
+		  (*prcm)->prm_abbldo_mm_ctrl,
+		  (*prcm)->prm_irqstatus_mpu,
+		  vcores->mm.abb_tx_done_mask,
+		  OMAP_ABB_FAST_OPP);
 
 	debug("gpu: %d\n", vcores->gpu.value);
 	do_scale_vcore(vcores->gpu.addr, vcores->gpu.value, vcores->gpu.pmic);
@@ -626,56 +629,6 @@ void scale_vcores(struct vcores_data const *vcores)
 		  (*prcm)->prm_irqstatus_mpu,
 		  vcores->iva.abb_tx_done_mask,
 		  OMAP_ABB_FAST_OPP);
-	/* Might need udelay(1000) here if debug is enabled to see all prints */
-#else
-	u32 val;
-
-	val = optimize_vcore_voltage(&vcores->core);
-	do_scale_vcore(vcores->core.addr, val, vcores->core.pmic);
-
-	/*
-	 * IO delay recalibration should be done immediately after
-	 * adjusting AVS voltages for VDD_CORE_L.
-	 * Respective boards should call __recalibrate_iodelay()
-	 * with proper mux, virtual and manual mode configurations.
-	 */
-#ifdef CONFIG_IODELAY_RECALIBRATION
-	recalibrate_iodelay();
-#endif
-
-	val = optimize_vcore_voltage(&vcores->mpu);
-	do_scale_vcore(vcores->mpu.addr, val, vcores->mpu.pmic);
-
-	/* Configure MPU ABB LDO after scale */
-	abb_setup(vcores->mpu.efuse.reg,
-		  (*ctrl)->control_wkup_ldovbb_mpu_voltage_ctrl,
-		  (*prcm)->prm_abbldo_mpu_setup,
-		  (*prcm)->prm_abbldo_mpu_ctrl,
-		  (*prcm)->prm_irqstatus_mpu_2,
-		  vcores->mpu.abb_tx_done_mask,
-		  OMAP_ABB_FAST_OPP);
-
-	val = optimize_vcore_voltage(&vcores->mm);
-	do_scale_vcore(vcores->mm.addr, val, vcores->mm.pmic);
-
-	/* Configure MM ABB LDO after scale */
-	abb_setup(vcores->mm.efuse.reg,
-		  (*ctrl)->control_wkup_ldovbb_mm_voltage_ctrl,
-		  (*prcm)->prm_abbldo_mm_setup,
-		  (*prcm)->prm_abbldo_mm_ctrl,
-		  (*prcm)->prm_irqstatus_mpu,
-		  vcores->mm.abb_tx_done_mask,
-		  OMAP_ABB_FAST_OPP);
-
-	val = optimize_vcore_voltage(&vcores->gpu);
-	do_scale_vcore(vcores->gpu.addr, val, vcores->gpu.pmic);
-
-	val = optimize_vcore_voltage(&vcores->eve);
-	do_scale_vcore(vcores->eve.addr, val, vcores->eve.pmic);
-
-	val = optimize_vcore_voltage(&vcores->iva);
-	do_scale_vcore(vcores->iva.addr, val, vcores->iva.pmic);
-#endif
 }
 
 static inline void enable_clock_domain(u32 const clkctrl_reg, u32 enable_mode)

arch/arm/cpu/armv7/omap3/Kconfig

@@ -6,55 +6,39 @@ choice
 
 config TARGET_AM3517_EVM
 	bool "AM3517 EVM"
-	select SUPPORT_SPL
 
 config TARGET_MT_VENTOUX
 	bool "TeeJet Mt.Ventoux"
-	select SUPPORT_SPL
 
 config TARGET_OMAP3_BEAGLE
 	bool "TI OMAP3 BeagleBoard"
-	select SUPPORT_SPL
 	select DM
 	select DM_SERIAL
 	select DM_GPIO
 
 config TARGET_CM_T35
 	bool "CompuLab CM-T3530 and CM-T3730 boards"
-	select SUPPORT_SPL
 
 config TARGET_CM_T3517
 	bool "CompuLab CM-T3517 boards"
 
 config TARGET_DEVKIT8000
 	bool "TimLL OMAP3 Devkit8000"
-	select SUPPORT_SPL
 	select DM
 	select DM_SERIAL
 	select DM_GPIO
 
 config TARGET_OMAP3_EVM
 	bool "TI OMAP3 EVM"
-	select SUPPORT_SPL
-
-config TARGET_OMAP3_EVM_QUICK_MMC
-	bool "TI OMAP3 EVM Quick MMC"
-	select SUPPORT_SPL
-
-config TARGET_OMAP3_EVM_QUICK_NAND
-	bool "TI OMAP3 EVM Quick NAND"
-	select SUPPORT_SPL
 
 config TARGET_OMAP3_IGEP00X0
 	bool "IGEP"
-	select SUPPORT_SPL
 	select DM
 	select DM_SERIAL
 	select DM_GPIO
 
 config TARGET_OMAP3_OVERO
 	bool "OMAP35xx Gumstix Overo"
-	select SUPPORT_SPL
 	select DM
 	select DM_SERIAL
 	select DM_GPIO
@@ -67,51 +51,42 @@ config TARGET_OMAP3_ZOOM1
 
 config TARGET_AM3517_CRANE
 	bool "am3517_crane"
-	select SUPPORT_SPL
 
 config TARGET_OMAP3_PANDORA
 	bool "OMAP3 Pandora"
 
 config TARGET_ECO5PK
 	bool "ECO5PK"
-	select SUPPORT_SPL
 
 config TARGET_TRICORDER
 	bool "Tricorder"
-	select SUPPORT_SPL
 
 config TARGET_MCX
 	bool "MCX"
-	select SUPPORT_SPL
 
 config TARGET_OMAP3_LOGIC
 	bool "OMAP3 Logic"
 	select DM
 	select DM_SERIAL
 	select DM_GPIO
-	select SUPPORT_SPL
 
 config TARGET_NOKIA_RX51
 	bool "Nokia RX51"
 
 config TARGET_TAO3530
 	bool "TAO3530"
-	select SUPPORT_SPL
 
 config TARGET_TWISTER
 	bool "Twister"
-	select SUPPORT_SPL
 
 config TARGET_OMAP3_CAIRO
 	bool "QUIPOS CAIRO"
-	select SUPPORT_SPL
 	select DM
 	select DM_SERIAL
 	select DM_GPIO
 
 config TARGET_SNIPER
 	bool "LG Optimus Black"
-	select SUPPORT_SPL
 	select DM
 	select DM_SERIAL
 	select DM_GPIO

arch/arm/cpu/armv7/omap5/Kconfig

@@ -13,6 +13,7 @@ config TARGET_OMAP5_UEVM
 config TARGET_DRA7XX_EVM
 	bool "TI DRA7XX"
 	select TI_I2C_BOARD_DETECT
+	select PHYS_64BIT
 
 config TARGET_AM57XX_EVM
 	bool "AM57XX"

arch/arm/cpu/armv7/omap5/hw_data.c

@@ -160,7 +160,7 @@ static const struct dpll_params per_dpll_params_768mhz_es2[NUM_SYS_CLKS] = {
 
 static const struct dpll_params per_dpll_params_768mhz_dra7xx[NUM_SYS_CLKS] = {
 	{32, 0, 4, 1, 3, 4, 4, 2, -1, -1, -1, -1},		/* 12 MHz   */
-	{96, 4, 4, 1, 3, 4, 4, 2, -1, -1, -1, -1},		/* 20 MHz   */
+	{96, 4, 4, 1, 3, 4, 10, 2, -1, -1, -1, -1},		/* 20 MHz   */
 	{160, 6, 4, 1, 3, 4, 4, 2, -1, -1, -1, -1},		/* 16.8 MHz */
 	{20, 0, 4, 1, 3, 4, 4, 2, -1, -1, -1, -1},		/* 19.2 MHz */
 	{192, 12, 4, 1, 3, 4, 4, 2, -1, -1, -1, -1},		/* 26 MHz   */
@@ -318,6 +318,7 @@ struct pmic_data palmas = {
 	.i2c_slave_addr	= SMPS_I2C_SLAVE_ADDR,
 	.pmic_bus_init	= sri2c_init,
 	.pmic_write	= omap_vc_bypass_send_value,
+	.gpio_en = 0,
 };
 
 /* The TPS659038 and TPS65917 are software-compatible, use common struct */
@@ -332,6 +333,7 @@ struct pmic_data tps659038 = {
 	.i2c_slave_addr	= TPS659038_I2C_SLAVE_ADDR,
 	.pmic_bus_init	= gpi2c_init,
 	.pmic_write	= palmas_i2c_write_u8,
+	.gpio_en = 0,
 };
 
 struct vcores_data omap5430_volts = {

arch/arm/cpu/armv7/psci-common.c

@@ -29,7 +29,7 @@ static u32 psci_target_pc[CONFIG_ARMV7_PSCI_NR_CPUS] __secure_data = { 0 };
 void __secure psci_save_target_pc(int cpu, u32 pc)
 {
 	psci_target_pc[cpu] = pc;
-	DSB;
+	dsb();
 }
 
 u32 __secure psci_get_target_pc(int cpu)

arch/arm/cpu/armv7/psci.S

@@ -46,20 +46,62 @@ ENTRY(default_psci_vector)
 ENDPROC(default_psci_vector)
 .weak default_psci_vector
 
+ENTRY(psci_version)
 ENTRY(psci_cpu_suspend)
 ENTRY(psci_cpu_off)
 ENTRY(psci_cpu_on)
+ENTRY(psci_affinity_info)
 ENTRY(psci_migrate)
+ENTRY(psci_migrate_info_type)
+ENTRY(psci_migrate_info_up_cpu)
+ENTRY(psci_system_off)
+ENTRY(psci_system_reset)
+ENTRY(psci_features)
+ENTRY(psci_cpu_freeze)
+ENTRY(psci_cpu_default_suspend)
+ENTRY(psci_node_hw_state)
+ENTRY(psci_system_suspend)
+ENTRY(psci_set_suspend_mode)
+ENTRY(psi_stat_residency)
+ENTRY(psci_stat_count)
 	mov	r0, #ARM_PSCI_RET_NI	@ Return -1 (Not Implemented)
 	mov	pc, lr
+ENDPROC(psci_stat_count)
+ENDPROC(psi_stat_residency)
+ENDPROC(psci_set_suspend_mode)
+ENDPROC(psci_system_suspend)
+ENDPROC(psci_node_hw_state)
+ENDPROC(psci_cpu_default_suspend)
+ENDPROC(psci_cpu_freeze)
+ENDPROC(psci_features)
+ENDPROC(psci_system_reset)
+ENDPROC(psci_system_off)
+ENDPROC(psci_migrate_info_up_cpu)
+ENDPROC(psci_migrate_info_type)
 ENDPROC(psci_migrate)
+ENDPROC(psci_affinity_info)
 ENDPROC(psci_cpu_on)
 ENDPROC(psci_cpu_off)
 ENDPROC(psci_cpu_suspend)
+ENDPROC(psci_version)
+.weak psci_version
 .weak psci_cpu_suspend
 .weak psci_cpu_off
 .weak psci_cpu_on
+.weak psci_affinity_info
 .weak psci_migrate
+.weak psci_migrate_info_type
+.weak psci_migrate_info_up_cpu
+.weak psci_system_off
+.weak psci_system_reset
+.weak psci_features
+.weak psci_cpu_freeze
+.weak psci_cpu_default_suspend
+.weak psci_node_hw_state
+.weak psci_system_suspend
+.weak psci_set_suspend_mode
+.weak psi_stat_residency
+.weak psci_stat_count
 
 _psci_table:
 	.word	ARM_PSCI_FN_CPU_SUSPEND
@@ -70,6 +112,42 @@ _psci_table:
 	.word	psci_cpu_on
 	.word	ARM_PSCI_FN_MIGRATE
 	.word	psci_migrate
+	.word	ARM_PSCI_0_2_FN_PSCI_VERSION
+	.word	psci_version
+	.word	ARM_PSCI_0_2_FN_CPU_SUSPEND
+	.word	psci_cpu_suspend
+	.word	ARM_PSCI_0_2_FN_CPU_OFF
+	.word	psci_cpu_off
+	.word	ARM_PSCI_0_2_FN_CPU_ON
+	.word	psci_cpu_on
+	.word	ARM_PSCI_0_2_FN_AFFINITY_INFO
+	.word	psci_affinity_info
+	.word	ARM_PSCI_0_2_FN_MIGRATE
+	.word	psci_migrate
+	.word	ARM_PSCI_0_2_FN_MIGRATE_INFO_TYPE
+	.word	psci_migrate_info_type
+	.word	ARM_PSCI_0_2_FN_MIGRATE_INFO_UP_CPU
+	.word	psci_migrate_info_up_cpu
+	.word	ARM_PSCI_0_2_FN_SYSTEM_OFF
+	.word	psci_system_off
+	.word	ARM_PSCI_0_2_FN_SYSTEM_RESET
+	.word	psci_system_reset
+	.word	ARM_PSCI_1_0_FN_PSCI_FEATURES
+	.word	psci_features
+	.word	ARM_PSCI_1_0_FN_CPU_FREEZE
+	.word	psci_cpu_freeze
+	.word	ARM_PSCI_1_0_FN_CPU_DEFAULT_SUSPEND
+	.word	psci_cpu_default_suspend
+	.word	ARM_PSCI_1_0_FN_NODE_HW_STATE
+	.word	psci_node_hw_state
+	.word	ARM_PSCI_1_0_FN_SYSTEM_SUSPEND
+	.word	psci_system_suspend
+	.word	ARM_PSCI_1_0_FN_SET_SUSPEND_MODE
+	.word	psci_set_suspend_mode
+	.word	ARM_PSCI_1_0_FN_STAT_RESIDENCY
+	.word	psi_stat_residency
+	.word	ARM_PSCI_1_0_FN_STAT_COUNT
+	.word	psci_stat_count
 	.word	0
 	.word	0
 

arch/arm/cpu/armv7/sunxi/psci.c

@@ -53,16 +53,16 @@ static void __secure __mdelay(u32 ms)
 	u32 reg = ONE_MS * ms;
 
 	cp15_write_cntp_tval(reg);
-	ISB;
+	isb();
 	cp15_write_cntp_ctl(3);
 
 	do {
-		ISB;
+		isb();
 		reg = cp15_read_cntp_ctl();
 	} while (!(reg & BIT(2)));
 
 	cp15_write_cntp_ctl(0);
-	ISB;
+	isb();
 }
 
 static void __secure clamp_release(u32 __maybe_unused *clamp)
@@ -164,7 +164,7 @@ static u32 __secure cp15_read_scr(void)
 static void __secure cp15_write_scr(u32 scr)
 {
 	asm volatile ("mcr p15, 0, %0, c1, c1, 0" : : "r" (scr));
-	ISB;
+	isb();
 }
 
 /*
@@ -190,7 +190,7 @@ void __secure __irq psci_fiq_enter(void)
 
 	/* End of interrupt */
 	writel(reg, GICC_BASE + GICC_EOIR);
-	DSB;
+	dsb();
 
 	/* Get CPU number */
 	cpu = (reg >> 10) & 0x7;
@@ -242,7 +242,7 @@ void __secure psci_cpu_off(void)
 
 	/* Ask CPU0 via SGI15 to pull the rug... */
 	writel(BIT(16) | 15, GICD_BASE + GICD_SGIR);
-	DSB;
+	dsb();
 
 	/* Wait to be turned off */
 	while (1)

arch/arm/cpu/armv7/virt-v7.c

@@ -54,10 +54,12 @@ static void relocate_secure_section(void)
 {
 #ifdef CONFIG_ARMV7_SECURE_BASE
 	size_t sz = __secure_end - __secure_start;
+	unsigned long szflush = ALIGN(sz + 1, CONFIG_SYS_CACHELINE_SIZE);
 
 	memcpy((void *)CONFIG_ARMV7_SECURE_BASE, __secure_start, sz);
+
 	flush_dcache_range(CONFIG_ARMV7_SECURE_BASE,
-			   CONFIG_ARMV7_SECURE_BASE + sz + 1);
+			   CONFIG_ARMV7_SECURE_BASE + szflush);
 	protect_secure_section();
 	invalidate_icache_all();
 #endif

arch/arm/cpu/armv8/Kconfig

@@ -1,7 +1,7 @@
 if ARM64
 
 config ARMV8_MULTIENTRY
-        boolean "Enable multiple CPUs to enter into U-Boot"
+        bool "Enable multiple CPUs to enter into U-Boot"
 
 config ARMV8_SPIN_TABLE
 	bool "Support spin-table enable method"

arch/arm/cpu/armv8/cache_v8.c

@@ -380,6 +380,7 @@ void setup_pgtables(void)
 static void setup_all_pgtables(void)
 {
 	u64 tlb_addr = gd->arch.tlb_addr;
+	u64 tlb_size = gd->arch.tlb_size;
 
 	/* Reset the fill ptr */
 	gd->arch.tlb_fillptr = tlb_addr;
@@ -388,10 +389,13 @@ static void setup_all_pgtables(void)
 	setup_pgtables();
 
 	/* Create emergency page tables */
+	gd->arch.tlb_size -= (uintptr_t)gd->arch.tlb_fillptr -
+			     (uintptr_t)gd->arch.tlb_addr;
 	gd->arch.tlb_addr = gd->arch.tlb_fillptr;
 	setup_pgtables();
 	gd->arch.tlb_emerg = gd->arch.tlb_addr;
 	gd->arch.tlb_addr = tlb_addr;
+	gd->arch.tlb_size = tlb_size;
 }
 
 /* to activate the MMU we need to set up virtual memory */

arch/arm/cpu/armv8/fsl-layerscape/Makefile

@@ -33,3 +33,7 @@ endif
 ifneq ($(CONFIG_LS1012A),)
 obj-$(CONFIG_SYS_HAS_SERDES) += ls1012a_serdes.o
 endif
+
+ifneq ($(CONFIG_LS1046A),)
+obj-$(CONFIG_SYS_HAS_SERDES) += ls1046a_serdes.o
+endif

arch/arm/cpu/armv8/fsl-layerscape/cpu.c

@@ -145,11 +145,14 @@ static inline void final_mmu_setup(void)
 	set_ttbr_tcr_mair(el, gd->arch.tlb_addr, get_tcr(el, NULL, NULL),
 			  MEMORY_ATTRIBUTES);
 	/*
-	 * MMU is already enabled, just need to invalidate TLB to load the
+	 * EL3 MMU is already enabled, just need to invalidate TLB to load the
 	 * new table. The new table is compatible with the current table, if
 	 * MMU somehow walks through the new table before invalidation TLB,
 	 * it still works. So we don't need to turn off MMU here.
+	 * When EL2 MMU table is created by calling this function, MMU needs
+	 * to be enabled.
 	 */
+	set_sctlr(get_sctlr() | CR_M);
 }
 
 u64 get_page_table_size(void)
@@ -309,7 +312,8 @@ int print_cpuinfo(void)
 		printf("CPU%d(%s):%-4s MHz  ", core,
 		       type == TY_ITYP_VER_A7 ? "A7 " :
 		       (type == TY_ITYP_VER_A53 ? "A53" :
-			(type == TY_ITYP_VER_A57 ? "A57" : "   ")),
+		       (type == TY_ITYP_VER_A57 ? "A57" :
+		       (type == TY_ITYP_VER_A72 ? "A72" : "   "))),
 		       strmhz(buf, sysinfo.freq_processor[core]));
 	}
 	printf("\n       Bus:      %-4s MHz  ",

arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc

@@ -3,6 +3,7 @@ SoC overview
 	1. LS1043A
 	2. LS2080A
 	3. LS1012A
+	4. LS1046A
 
 LS1043A
 ---------
@@ -127,3 +128,44 @@ The LS1012A SoC includes the following function and features:
     - Two WatchDog timers
     - ARM generic timer
  - QorIQ platform's trust architecture 2.1
+
+LS1046A
+--------
+The LS1046A integrated multicore processor combines four ARM Cortex-A72
+processor cores with datapath acceleration optimized for L2/3 packet
+processing, single pass security offload and robust traffic management
+and quality of service.
+
+The LS1046A SoC includes the following function and features:
+ - Four 64-bit ARM Cortex-A72 CPUs
+ - 2 MB unified L2 Cache
+ - One 64-bit DDR4 SDRAM memory controllers with ECC and interleaving
+   support
+ - Data Path Acceleration Architecture (DPAA) incorporating acceleration the
+   the following functions:
+   - Packet parsing, classification, and distribution (FMan)
+   - Queue management for scheduling, packet sequencing, and congestion
+     management (QMan)
+   - Hardware buffer management for buffer allocation and de-allocation (BMan)
+   - Cryptography acceleration (SEC)
+ - Two Configurable x4 SerDes
+   - Two PLLs per four-lane SerDes
+   - Support for 10G operation
+ - Ethernet interfaces by FMan
+   - Up to 2 x XFI supporting 10G interface (MAC 9, 10)
+   - Up to 1 x QSGMII (MAC 5, 6, 10, 1)
+   - Up to 4 x SGMII supporting 1000Mbps (MAC 5, 6, 9, 10)
+   - Up to 3 x SGMII supporting 2500Mbps (MAC 5, 9, 10)
+   - Up to 2 x RGMII supporting 1000Mbps (MAC 3, 4)
+ - High-speed peripheral interfaces
+   - Three PCIe 3.0 controllers, one supporting x4 operation
+   - One serial ATA (SATA 3.0) controllers
+ - Additional peripheral interfaces
+   - Three high-speed USB 3.0 controllers with integrated PHY
+   - Enhanced secure digital host controller (eSDXC/eMMC)
+   - Quad Serial Peripheral Interface (QSPI) Controller
+   - Serial peripheral interface (SPI) controller
+   - Four I2C controllers
+   - Two DUARTs
+   - Integrated flash controller (IFC) supporting NAND and NOR flash
+ - QorIQ platform's trust architecture 2.1

arch/arm/cpu/armv8/fsl-layerscape/fsl_lsch2_serdes.c

@@ -13,6 +13,9 @@
 #ifdef CONFIG_SYS_FSL_SRDS_1
 static u8 serdes1_prtcl_map[SERDES_PRCTL_COUNT];
 #endif
+#ifdef CONFIG_SYS_FSL_SRDS_2
+static u8 serdes2_prtcl_map[SERDES_PRCTL_COUNT];
+#endif
 
 int is_serdes_configured(enum srds_prtcl device)
 {
@@ -21,6 +24,9 @@ int is_serdes_configured(enum srds_prtcl device)
 #ifdef CONFIG_SYS_FSL_SRDS_1
 	ret |= serdes1_prtcl_map[device];
 #endif
+#ifdef CONFIG_SYS_FSL_SRDS_2
+	ret |= serdes2_prtcl_map[device];
+#endif
 
 	return !!ret;
 }
@@ -37,6 +43,12 @@ int serdes_get_first_lane(u32 sd, enum srds_prtcl device)
 		cfg &= FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_MASK;
 		cfg >>= FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_SHIFT;
 		break;
+#endif
+#ifdef CONFIG_SYS_FSL_SRDS_2
+	case FSL_SRDS_2:
+		cfg &= FSL_CHASSIS2_RCWSR4_SRDS2_PRTCL_MASK;
+		cfg >>= FSL_CHASSIS2_RCWSR4_SRDS2_PRTCL_SHIFT;
+		break;
 #endif
 	default:
 		printf("invalid SerDes%d\n", sd);
@@ -114,4 +126,11 @@ void fsl_serdes_init(void)
 		    FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_SHIFT,
 		    serdes1_prtcl_map);
 #endif
+#ifdef CONFIG_SYS_FSL_SRDS_2
+	serdes_init(FSL_SRDS_2,
+		    CONFIG_SYS_FSL_SERDES_ADDR,
+		    FSL_CHASSIS2_RCWSR4_SRDS2_PRTCL_MASK,
+		    FSL_CHASSIS2_RCWSR4_SRDS2_PRTCL_SHIFT,
+		    serdes2_prtcl_map);
+#endif
 }

arch/arm/cpu/armv8/fsl-layerscape/fsl_lsch2_speed.c

@@ -107,6 +107,12 @@ void get_sys_info(struct sys_info *sys_info)
 	case 3:
 		sys_info->freq_fman[0] = freq_c_pll[0] / 3;
 		break;
+	case 4:
+		sys_info->freq_fman[0] = freq_c_pll[0] / 4;
+		break;
+	case 5:
+		sys_info->freq_fman[0] = sys_info->freq_systembus;
+		break;
 	case 6:
 		sys_info->freq_fman[0] = freq_c_pll[1] / 2;
 		break;
@@ -124,8 +130,23 @@ void get_sys_info(struct sys_info *sys_info)
 #ifdef CONFIG_FSL_ESDHC
 #ifdef CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK
 	rcw_tmp = in_be32(&gur->rcwsr[15]);
-	rcw_tmp = (rcw_tmp & HWA_CGA_M2_CLK_SEL) >> HWA_CGA_M2_CLK_SHIFT;
-	sys_info->freq_sdhc = freq_c_pll[1] / rcw_tmp;
+	switch ((rcw_tmp & HWA_CGA_M2_CLK_SEL) >> HWA_CGA_M2_CLK_SHIFT) {
+	case 1:
+		sys_info->freq_sdhc = freq_c_pll[1];
+		break;
+	case 2:
+		sys_info->freq_sdhc = freq_c_pll[1] / 2;
+		break;
+	case 3:
+		sys_info->freq_sdhc = freq_c_pll[1] / 3;
+		break;
+	case 6:
+		sys_info->freq_sdhc = freq_c_pll[0] / 2;
+		break;
+	default:
+		printf("Error: Unknown ESDHC clock select!\n");
+		break;
+	}
 #else
 	sys_info->freq_sdhc = sys_info->freq_systembus;
 #endif

arch/arm/cpu/armv8/fsl-layerscape/ls1046a_serdes.c

@@ -0,0 +1,99 @@
+/*
+ * Copyright 2016 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/fsl_serdes.h>
+#include <asm/arch/immap_lsch2.h>
+
+struct serdes_config {
+	u32 protocol;
+	u8 lanes[SRDS_MAX_LANES];
+};
+
+static struct serdes_config serdes1_cfg_tbl[] = {
+	/* SerDes 1 */
+	{0x3333, {SGMII_FM1_DTSEC9, SGMII_FM1_DTSEC10, SGMII_FM1_DTSEC5,
+		  SGMII_FM1_DTSEC6} },
+	{0x1133, {XFI_FM1_MAC9, XFI_FM1_MAC10, SGMII_FM1_DTSEC5,
+		  SGMII_FM1_DTSEC6} },
+	{0x1333, {XFI_FM1_MAC9, SGMII_FM1_DTSEC10, SGMII_FM1_DTSEC5,
+		  SGMII_FM1_DTSEC6} },
+	{0x2333, {SGMII_2500_FM1_DTSEC9, SGMII_FM1_DTSEC10, SGMII_FM1_DTSEC5,
+		  SGMII_FM1_DTSEC6} },
+	{0x2233, {SGMII_2500_FM1_DTSEC9, SGMII_2500_FM1_DTSEC10,
+		  SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6} },
+	{0x1040, {XFI_FM1_MAC9, NONE, QSGMII_FM1_A, NONE} },
+	{0x2040, {SGMII_2500_FM1_DTSEC9, NONE, QSGMII_FM1_A, NONE} },
+	{0x1163, {XFI_FM1_MAC9, XFI_FM1_MAC10, PCIE1, SGMII_FM1_DTSEC6} },
+	{0x2263, {SGMII_2500_FM1_DTSEC9, SGMII_2500_FM1_DTSEC10, PCIE1,
+		  SGMII_FM1_DTSEC6} },
+	{0x3363, {SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6, PCIE1,
+		  SGMII_FM1_DTSEC6} },
+	{0x2223, {SGMII_2500_FM1_DTSEC9, SGMII_2500_FM1_DTSEC10,
+		  SGMII_2500_FM1_DTSEC5, SGMII_FM1_DTSEC6} },
+	{}
+};
+
+static struct serdes_config serdes2_cfg_tbl[] = {
+	/* SerDes 2 */
+	{0x8888, {PCIE1, PCIE1, PCIE1, PCIE1} },
+	{0x5559, {PCIE1, PCIE2, PCIE3, SATA1} },
+	{0x5577, {PCIE1, PCIE2, PCIE3, PCIE3} },
+	{0x5506, {PCIE1, PCIE2, NONE, PCIE3} },
+	{0x0506, {NONE, PCIE2, NONE, PCIE3} },
+	{0x0559, {NONE, PCIE2, PCIE3, SATA1} },
+	{0x5A59, {PCIE1, SGMII_FM1_DTSEC2, PCIE3, SATA1} },
+	{0x5A06, {PCIE1, SGMII_FM1_DTSEC2, NONE, PCIE3} },
+	{}
+};
+
+static struct serdes_config *serdes_cfg_tbl[] = {
+	serdes1_cfg_tbl,
+	serdes2_cfg_tbl,
+};
+
+enum srds_prtcl serdes_get_prtcl(int serdes, int cfg, int lane)
+{
+	struct serdes_config *ptr;
+
+	if (serdes >= ARRAY_SIZE(serdes_cfg_tbl))
+		return 0;
+
+	ptr = serdes_cfg_tbl[serdes];
+	while (ptr->protocol) {
+		if (ptr->protocol == cfg)
+			return ptr->lanes[lane];
+		ptr++;
+	}
+
+	return 0;
+}
+
+int is_serdes_prtcl_valid(int serdes, u32 prtcl)
+{
+	int i;
+	struct serdes_config *ptr;
+
+	if (serdes >= ARRAY_SIZE(serdes_cfg_tbl))
+		return 0;
+
+	ptr = serdes_cfg_tbl[serdes];
+	while (ptr->protocol) {
+		if (ptr->protocol == prtcl)
+			break;
+		ptr++;
+	}
+
+	if (!ptr->protocol)
+		return 0;
+
+	for (i = 0; i < SRDS_MAX_LANES; i++) {
+		if (ptr->lanes[i] != NONE)
+			return 1;
+	}
+
+	return 0;
+}

arch/arm/cpu/armv8/fsl-layerscape/ppa.c

@@ -24,7 +24,7 @@ int ppa_init(void)
 	u32 *boot_loc_ptr_l, *boot_loc_ptr_h;
 	int ret;
 
-#ifdef CONFIG_SYS_LS_PPA_FW_IN_NOR
+#ifdef CONFIG_SYS_LS_PPA_FW_IN_XIP
 	ppa_fit_addr = (void *)CONFIG_SYS_LS_PPA_FW_ADDR;
 #else
 #error "No CONFIG_SYS_LS_PPA_FW_IN_xxx defined"

arch/arm/cpu/armv8/zynqmp/Kconfig

@@ -20,4 +20,8 @@ config SYS_CONFIG_NAME
 config ZYNQMP_USB
 	bool "Configure ZynqMP USB"
 
+config SYS_MALLOC_F_LEN
+	default 0x600
+
+
 endif

arch/arm/dts/Makefile

@@ -31,7 +31,12 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += \
 	rk3288-firefly.dtb \
 	rk3288-jerry.dtb \
 	rk3288-rock2-square.dtb \
-	rk3036-sdk.dtb
+	rk3288-evb.dtb \
+	rk3288-fennec.dtb \
+	rk3288-miniarm.dtb \
+	rk3288-popmetal.dtb \
+	rk3036-sdk.dtb \
+	rk3399-evb.dtb
 dtb-$(CONFIG_ARCH_MESON) += \
 	meson-gxbb-odroidc2.dtb
 dtb-$(CONFIG_TEGRA) += tegra20-harmony.dtb \
@@ -246,6 +251,7 @@ dtb-$(CONFIG_MACH_SUN8I_H3) += \
 	sun8i-h3-orangepi-lite.dtb \
 	sun8i-h3-orangepi-one.dtb \
 	sun8i-h3-orangepi-pc.dtb \
+	sun8i-h3-orangepi-pc-plus.dtb \
 	sun8i-h3-orangepi-plus.dtb
 dtb-$(CONFIG_MACH_SUN50I) += \
 	sun50i-a64-pine64-plus.dtb \
@@ -264,6 +270,9 @@ dtb-$(CONFIG_SOC_KEYSTONE) += k2hk-evm.dtb \
 	k2e-evm.dtb \
 	k2g-evm.dtb
 
+dtb-$(CONFIG_TARGET_SAMA5D2_XPLAINED) += \
+	at91-sama5d2_xplained.dtb
+
 targets += $(dtb-y)
 
 # Add any required device tree compiler flags here

arch/arm/dts/am57xx-idk-common.dtsi

@@ -300,3 +300,52 @@
 	ti,non-removable;
 	max-frequency = <96000000>;
 };
+
+&qspi {
+	status = "okay";
+
+	spi-max-frequency = <76800000>;
+	m25p80@0 {
+		compatible = "s25fl256s1","spi-flash";
+		spi-max-frequency = <76800000>;
+		reg = <0>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		/* MTD partition table.
+		 * The ROM checks the first four physical blocks
+		 * for a valid file to boot and the flash here is
+		 * 64KiB block size.
+		 */
+		partition@0 {
+			label = "QSPI.SPL";
+			reg = <0x00000000 0x000040000>;
+		};
+		partition@1 {
+			label = "QSPI.u-boot";
+			reg = <0x00040000 0x00100000>;
+		};
+		partition@2 {
+			label = "QSPI.u-boot-spl-os";
+			reg = <0x00140000 0x00080000>;
+		};
+		partition@3 {
+			label = "QSPI.u-boot-env";
+			reg = <0x001c0000 0x00010000>;
+		};
+		partition@4 {
+			label = "QSPI.u-boot-env.backup1";
+			reg = <0x001d0000 0x0010000>;
+		};
+		partition@5 {
+			label = "QSPI.kernel";
+			reg = <0x001e0000 0x0800000>;
+		};
+		partition@6 {
+			label = "QSPI.file-system";
+			reg = <0x009e0000 0x01620000>;
+		};
+	};
+};

arch/arm/dts/at91-sama5d2_xplained.dts

@@ -0,0 +1,200 @@
+/dts-v1/;
+#include "sama5d2.dtsi"
+#include "sama5d2-pinfunc.h"
+
+/ {
+	model = "Atmel SAMA5D2 Xplained";
+	compatible = "atmel,sama5d2-xplained", "atmel,sama5d2", "atmel,sama5";
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	ahb {
+		usb1: ohci@00400000 {
+			num-ports = <3>;
+			atmel,vbus-gpio = <&pioA 42 0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usb_default>;
+			status = "okay";
+		};
+
+		usb2: ehci@00500000 {
+			status = "okay";
+		};
+
+		sdmmc0: sdio-host@a0000000 {
+			bus-width = <8>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_sdmmc0_cmd_dat_default &pinctrl_sdmmc0_ck_cd_default>;
+			status = "okay";
+		};
+
+		sdmmc1: sdio-host@b0000000 {
+			bus-width = <4>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_sdmmc1_cmd_dat_default &pinctrl_sdmmc1_ck_cd_default>;
+			status = "okay"; /* conflict with qspi0 */
+		};
+
+		apb {
+			qspi0: spi@f0020000 {
+				status = "okay";
+
+				flash@0 {
+					compatible = "atmel,sama5d2-qspi-flash";
+					reg = <0>;
+					#address-cells = <1>;
+					#size-cells = <1>;
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_qspi0_default>;
+					spi-max-frequency = <83000000>;
+
+					partition@00000000 {
+						label = "boot";
+						reg = <0x00000000 0x00c00000>;
+					};
+
+					partition@00c00000 {
+						label = "rootfs";
+						reg = <0x00c00000 0x00000000>;
+					};
+				};
+			};
+
+			spi0: spi@f8000000 {
+				cs-gpios = <&pioA 17 0>, <0>, <0>, <0>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_spi0_default>;
+				status = "okay";
+
+				spi_flash@0 {
+					compatible = "spi-flash";
+					reg = <0>;
+					spi-max-frequency = <50000000>;
+				};
+			};
+
+			macb0: ethernet@f8008000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_macb0_rmii &pinctrl_macb0_phy_irq>;
+				phy-mode = "rmii";
+				status = "okay";
+
+				ethernet-phy@1 {
+					reg = <0x1>;
+				};
+			};
+
+			uart1: serial@f8020000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_uart1_default>;
+				status = "okay";
+			};
+
+			i2c1: i2c@fc028000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c1_default>;
+				status = "okay";
+			};
+
+			pioA: gpio@fc038000 {
+				pinctrl {
+					pinctrl_i2c1_default: i2c1_default {
+						pinmux = <PIN_PD4__TWD1>,
+							 <PIN_PD5__TWCK1>;
+						bias-disable;
+					};
+
+					pinctrl_macb0_phy_irq: macb0_phy_irq {
+						pinmux = <PIN_PC9__GPIO>;
+						bias-disable;
+					};
+
+					pinctrl_macb0_rmii: macb0_rmii {
+						pinmux = <PIN_PB14__GTXCK>,
+							 <PIN_PB15__GTXEN>,
+							 <PIN_PB16__GRXDV>,
+							 <PIN_PB17__GRXER>,
+							 <PIN_PB18__GRX0>,
+							 <PIN_PB19__GRX1>,
+							 <PIN_PB20__GTX0>,
+							 <PIN_PB21__GTX1>,
+							 <PIN_PB22__GMDC>,
+							 <PIN_PB23__GMDIO>;
+						bias-disable;
+					};
+
+					pinctrl_qspi0_default: qspi0_default {
+						pinmux = <PIN_PA22__QSPI0_SCK>,
+							 <PIN_PA23__QSPI0_CS>,
+							 <PIN_PA24__QSPI0_IO0>,
+							 <PIN_PA25__QSPI0_IO1>,
+							 <PIN_PA26__QSPI0_IO2>,
+							 <PIN_PA27__QSPI0_IO3>;
+						bias-disable;
+					};
+
+					pinctrl_sdmmc0_cmd_dat_default: sdmmc0_cmd_dat_default {
+						pinmux = <PIN_PA1__SDMMC0_CMD>,
+							 <PIN_PA2__SDMMC0_DAT0>,
+							 <PIN_PA3__SDMMC0_DAT1>,
+							 <PIN_PA4__SDMMC0_DAT2>,
+							 <PIN_PA5__SDMMC0_DAT3>,
+							 <PIN_PA6__SDMMC0_DAT4>,
+							 <PIN_PA7__SDMMC0_DAT5>,
+							 <PIN_PA8__SDMMC0_DAT6>,
+							 <PIN_PA9__SDMMC0_DAT7>;
+						bias-pull-up;
+					};
+
+					pinctrl_sdmmc0_ck_cd_default: sdmmc0_ck_cd_default {
+						pinmux = <PIN_PA0__SDMMC0_CK>,
+							 <PIN_PA10__SDMMC0_RSTN>,
+							 <PIN_PA11__SDMMC0_VDDSEL>,
+							 <PIN_PA13__SDMMC0_CD>;
+						bias-disable;
+					};
+
+					pinctrl_sdmmc1_cmd_dat_default: sdmmc1_cmd_dat_default {
+						pinmux = <PIN_PA28__SDMMC1_CMD>,
+							 <PIN_PA18__SDMMC1_DAT0>,
+							 <PIN_PA19__SDMMC1_DAT1>,
+							 <PIN_PA20__SDMMC1_DAT2>,
+							 <PIN_PA21__SDMMC1_DAT3>;
+						bias-pull-up;
+					};
+
+					pinctrl_sdmmc1_ck_cd_default: sdmmc1_ck_cd_default {
+						pinmux = <PIN_PA22__SDMMC1_CK>,
+							 <PIN_PA30__SDMMC1_CD>;
+						bias-disable;
+					};
+
+					pinctrl_spi0_default: spi0_default {
+						pinmux = <PIN_PA14__SPI0_SPCK>,
+							 <PIN_PA15__SPI0_MOSI>,
+							 <PIN_PA16__SPI0_MISO>;
+						bias-disable;
+					};
+
+					pinctrl_uart1_default: uart1_default {
+						pinmux = <PIN_PD2__URXD1>,
+							 <PIN_PD3__UTXD1>;
+						bias-disable;
+					};
+
+					pinctrl_usb_default: usb_default {
+						pinmux = <PIN_PB10__GPIO>;
+						bias-disable;
+					};
+
+					pinctrl_usba_vbus: usba_vbus {
+						pinmux = <PIN_PA31__GPIO>;
+						bias-disable;
+					};
+				};
+			};
+		};
+	};
+};

arch/arm/dts/dra7-evm.dts

@@ -24,6 +24,15 @@
 		reg = <0x80000000 0x60000000>; /* 1536 MB */
 	};
 
+	evm_3v3_sd: fixedregulator-sd {
+		compatible = "regulator-fixed";
+		regulator-name = "evm_3v3_sd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+		gpio = <&pcf_gpio_21 5 GPIO_ACTIVE_HIGH>;
+	};
+
 	mmc2_3v3: fixedregulator-mmc2 {
 		compatible = "regulator-fixed";
 		regulator-name = "mmc2_3v3";
@@ -415,6 +424,7 @@
 		interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
+		u-boot,i2c-offset-len = <0>;
 	};
 
 };
@@ -467,7 +477,8 @@
 
 &mmc1 {
 	status = "okay";
-	vmmc-supply = <&ldo1_reg>;
+	vmmc-supply = <&evm_3v3_sd>;
+	vmmc_aux-supply = <&ldo1_reg>;
 	bus-width = <4>;
 	/*
 	 * SDCD signal is not being used here - using the fact that GPIO mode
@@ -491,7 +502,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&qspi1_pins>;
 
-	spi-max-frequency = <64000000>;
+	spi-max-frequency = <76800000>;
 	m25p80@0 {
 		compatible = "s25fl256s1","spi-flash";
 		spi-max-frequency = <64000000>;

arch/arm/dts/dra72-evm.dts

@@ -35,6 +35,15 @@
 		regulator-max-microvolt = <3300000>;
 	};
 
+	evm_3v3_sd: fixedregulator-sd {
+		compatible = "regulator-fixed";
+		regulator-name = "evm_3v3_sd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+		gpio = <&pcf_gpio_21 5 GPIO_ACTIVE_HIGH>;
+	};
+
 	extcon_usb1: extcon_usb1 {
 		compatible = "linux,extcon-usb-gpio";
 		id-gpio = <&pcf_gpio_21 1 GPIO_ACTIVE_HIGH>;
@@ -348,6 +357,7 @@
 		interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
+		u-boot,i2c-offset-len = <0>;
 	};
 };
 
@@ -369,6 +379,7 @@
 		 * VIN6_SEL_S0 is low, thus selecting McASP3 over VIN6
 		 */
 		lines-initial-states = <0x0f2b>;
+		u-boot,i2c-offset-len = <0>;
 	};
 };
 
@@ -497,7 +508,8 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc1_pins_default>;
 
-	vmmc-supply = <&ldo1_reg>;
+	vmmc_aux-supply = <&ldo1_reg>;
+	vmmc-supply = <&evm_3v3_sd>;
 	bus-width = <4>;
 	/*
 	 * SDCD signal is not being used here - using the fact that GPIO mode
@@ -576,6 +588,7 @@
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&cpsw_default>;
 	pinctrl-1 = <&cpsw_sleep>;
+	mode-gpios = <&pcf_gpio_21 4 GPIO_ACTIVE_HIGH>;
 };
 
 &cpsw_emac1 {
@@ -587,7 +600,6 @@
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&davinci_mdio_default>;
 	pinctrl-1 = <&davinci_mdio_sleep>;
-	active_slave = <1>;
 };
 
 &dcan1 {
@@ -603,7 +615,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&qspi1_pins>;
 
-	spi-max-frequency = <64000000>;
+	spi-max-frequency = <76800000>;
 	m25p80@0 {
 		compatible = "s25fl256s1","spi-flash";
 		spi-max-frequency = <64000000>;

arch/arm/dts/k2g-evm.dts

@@ -100,3 +100,11 @@
                 };
         };
 };
+
+&mmc0 {
+	status = "okay";
+};
+
+&mmc1 {
+	status = "okay";
+};

arch/arm/dts/k2g.dtsi

@@ -149,5 +149,28 @@
 			#size-cells = <0>;
 			status = "disabled";
 		};
+
+		mmc0: mmc@23000000 {
+			compatible = "ti,omap4-hsmmc";
+			reg = <0x23000000 0x400>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_EDGE_RISING>;
+			bus-width = <4>;
+			ti,needs-special-reset;
+			no-1-8-v;
+			max-frequency = <96000000>;
+			status = "disabled";
+		};
+
+		mmc1: mmc@23100000 {
+			compatible = "ti,omap4-hsmmc";
+			reg = <0x23100000 0x400>;
+			interrupts = <GIC_SPI 97 IRQ_TYPE_EDGE_RISING>;
+			bus-width = <8>;
+			ti,needs-special-reset;
+			ti,non-removable;
+			max-frequency = <96000000>;
+			status = "disabled";
+			clock-names = "fck";
+		};
 	};
 };

arch/arm/dts/ls1021a.dtsi

@@ -368,7 +368,7 @@
 		};
 
 		usb3@3100000 {
-			compatible = "snps,dwc3";
+			compatible = "fsl,layerscape-dwc3";
 			reg = <0x3100000 0x10000>;
 			interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
 			dr_mode = "host";

arch/arm/dts/rk3036-sdk.dts

@@ -41,6 +41,4 @@
 
 &usb_otg {
 	status = "okay";
-
-	dr_mode = "host";
 };

arch/arm/dts/rk3288-evb.dts

@@ -0,0 +1,60 @@
+/*
+ * (C) Copyright 2016 Rockchip Electronics Co., Ltd
+ *
+ * SPDX-License-Identifier:     GPL-2.0+ X11
+ */
+
+/dts-v1/;
+#include "rk3288-evb.dtsi"
+
+/ {
+	model = "Evb-RK3288";
+	compatible = "evb-rk3288,evb-rk3288", "rockchip,rk3288";
+
+	chosen {
+		stdout-path = &uart2;
+	};
+};
+
+&dmc {
+	rockchip,num-channels = <2>;
+	rockchip,pctl-timing = <0x215 0xc8 0x0 0x35 0x26 0x2 0x70 0x2000d
+		0x6 0x0 0x8 0x4 0x17 0x24 0xd 0x6
+		0x4 0x8 0x4 0x76 0x4 0x0 0x30 0x0
+		0x1 0x2 0x2 0x4 0x0 0x0 0xc0 0x4
+		0x8 0x1f4>;
+	rockchip,phy-timing = <0x48d7dd93 0x187008d8 0x121076
+		0x0 0xc3 0x6 0x2>;
+	/* Add a dummy value to cause of-platdata think this is bytes */
+	rockchip,sdram-channel = /bits/ 8 <0x2 0xa 0x3 0x2 0x2 0x0 0xe 0xe 0xff>;
+	rockchip,sdram-params = <0x20d266a4 0x5b6 2 533000000 6 9 0>;
+};
+
+&pinctrl {
+	u-boot,dm-pre-reloc;
+};
+
+&pwm1 {
+	status = "okay";
+};
+
+&uart2 {
+	u-boot,dm-pre-reloc;
+	reg-shift = <2>;
+};
+
+&sdmmc {
+	u-boot,dm-pre-reloc;
+};
+
+&emmc {
+	u-boot,dm-pre-reloc;
+};
+
+&gpio3 {
+	u-boot,dm-pre-reloc;
+};
+
+&gpio8 {
+	u-boot,dm-pre-reloc;
+};

arch/arm/dts/rk3288-evb.dtsi

@@ -0,0 +1,379 @@
+/*
+ * (C) Copyright 2016 Rockchip Electronics Co., Ltd
+ *
+ * SPDX-License-Identifier:     GPL-2.0+ X11
+ */
+
+#include "rk3288.dtsi"
+
+/ {
+	memory {
+		reg = <0 0x80000000>;
+	};
+
+	keys: gpio-keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		button@0 {
+			gpio-key,wakeup = <1>;
+			gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
+			label = "GPIO Power";
+			linux,code = <116>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pwr_key>;
+		};
+	};
+
+	vcc_sys: vsys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_sys";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vcc_flash: flash-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_flash";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_io>;
+	};
+
+	vcc_5v: usb-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vcc_sys>;
+	};
+
+	vcc_host_5v: usb-host-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 14 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&host_vbus_drv>;
+		regulator-name = "vcc_host_5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		vin-supply = <&vcc_5v>;
+	};
+
+	vcc_otg_5v: usb-otg-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&otg_vbus_drv>;
+		regulator-name = "vcc_otg_5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		vin-supply = <&vcc_5v>;
+	};
+};
+
+&cpu0 {
+	cpu0-supply = <&vdd_cpu>;
+};
+
+&emmc {
+	broken-cd;
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	disable-wp;
+	non-removable;
+	num-slots = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_clk>, <&emmc_cmd>, <&emmc_pwr>, <&emmc_bus8>;
+	vmmc-supply = <&vcc_io>;
+	vqmmc-supply = <&vcc_flash>;
+	status = "okay";
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c5>;
+	status = "okay";
+};
+
+&i2c0 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	vdd_cpu: syr827@40 {
+		compatible = "silergy,syr827";
+		fcs,suspend-voltage-selector = <1>;
+		reg = <0x40>;
+		regulator-name = "vdd_cpu";
+		regulator-min-microvolt = <850000>;
+		regulator-max-microvolt = <1350000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vcc_sys>;
+	};
+
+	vdd_gpu: syr828@41 {
+		compatible = "silergy,syr828";
+		fcs,suspend-voltage-selector = <1>;
+		reg = <0x41>;
+		regulator-name = "vdd_gpu";
+		regulator-min-microvolt = <850000>;
+		regulator-max-microvolt = <1350000>;
+		regulator-always-on;
+		vin-supply = <&vcc_sys>;
+	};
+
+	hym8563: hym8563@51 {
+		compatible = "haoyu,hym8563";
+		reg = <0x51>;
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "xin32k";
+		interrupt-parent = <&gpio7>;
+		interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&rtc_int>;
+	};
+
+	act8846: act8846@5a {
+		compatible = "active-semi,act8846";
+		reg = <0x5a>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pwr_hold>;
+		system-power-controller;
+
+		regulators {
+			vcc_ddr: REG1 {
+				regulator-name = "vcc_ddr";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-always-on;
+			};
+
+			vcc_io: REG2 {
+				regulator-name = "vcc_io";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vdd_log: REG3 {
+				regulator-name = "vdd_log";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-always-on;
+			};
+
+			vcc_20: REG4 {
+				regulator-name = "vcc_20";
+				regulator-min-microvolt = <2000000>;
+				regulator-max-microvolt = <2000000>;
+				regulator-always-on;
+			};
+
+			vccio_sd: REG5 {
+				regulator-name = "vccio_sd";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vdd10_lcd: REG6 {
+				regulator-name = "vdd10_lcd";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+			};
+
+			vcca_codec: REG7 {
+				regulator-name = "vcca_codec";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			vcc_tp: REG8 {
+				regulator-name = "vcca_33";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			vccio_pmu: REG9 {
+				regulator-name = "vccio_pmu";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			vdd_10: REG10 {
+				regulator-name = "vdd_10";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+			};
+
+			vcc_18: REG11 {
+				regulator-name = "vcc_18";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+
+			vcc18_lcd: REG12 {
+				regulator-name = "vcc18_lcd";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c4 {
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&pinctrl {
+	pcfg_output_high: pcfg-output-high {
+		output-high;
+	};
+
+	pcfg_output_low: pcfg-output-low {
+		output-low;
+	};
+
+	act8846 {
+		pwr_hold: pwr-hold {
+			rockchip,pins = <0 9 RK_FUNC_GPIO &pcfg_output_high>;
+		};
+	};
+
+	hym8563 {
+		rtc_int: rtc-int {
+			rockchip,pins = <0 4 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	keys {
+		pwr_key: pwr-key {
+			rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	sdmmc {
+		sdmmc_pwr: sdmmc-pwr {
+			rockchip,pins = <7 11 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	usb_host {
+		host_vbus_drv: host-vbus-drv {
+			rockchip,pins = <0 14 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	usb_otg {
+		otg_vbus_drv: otg-vbus-drv {
+			rockchip,pins = <0 12 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&saradc {
+	vref-supply = <&vcc_18>;
+	status = "okay";
+};
+
+&sdio0 {
+	broken-cd;
+	bus-width = <4>;
+	disable-wp;
+	non-removable;
+	num-slots = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdio0_bus4>, <&sdio0_cmd>, <&sdio0_clk>;
+	vmmc-supply = <&vcc_18>;
+	status = "disabled";
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-mmc-highspeed;
+	cap-sd-highspeed;
+	card-detect-delay = <200>;
+	disable-wp;
+	num-slots = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc_clk>, <&sdmmc_cmd>, <&sdmmc_cd>, <&sdmmc_bus4>;
+	vmmc-supply = <&vccio_sd>;
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_clk>, <&spi0_cs0>, <&spi0_tx>, <&spi0_rx>, <&spi0_cs1>;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_xfer>, <&uart0_cts>, <&uart0_rts>;
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&usb_host1 {
+	status = "okay";
+};
+
+&usb_otg {
+	status = "okay";
+};
+
+&vopb {
+	status = "okay";
+};
+
+&vopb_mmu {
+	status = "okay";
+};
+
+&vopl {
+	status = "okay";
+};
+
+&vopl_mmu {
+	status = "okay";
+};
+
+&wdt {
+	status = "okay";
+};

arch/arm/dts/rk3288-fennec.dts

@@ -0,0 +1,60 @@
+/*
+ * (C) Copyright 2016 Rockchip Electronics Co., Ltd
+ *
+ * SPDX-License-Identifier:     GPL-2.0+ X11
+ */
+
+/dts-v1/;
+#include "rk3288-fennec.dtsi"
+
+/ {
+	model = "Rockchip RK3288 Fennec Board";
+	compatible = "rockchip,rk3288-fennec", "rockchip,rk3288";
+
+	chosen {
+		stdout-path = &uart2;
+	};
+};
+
+&dmc {
+	rockchip,num-channels = <2>;
+	rockchip,pctl-timing = <0x215 0xc8 0x0 0x35 0x26 0x2 0x70 0x2000d
+		0x6 0x0 0x8 0x4 0x17 0x24 0xd 0x6
+		0x4 0x8 0x4 0x76 0x4 0x0 0x30 0x0
+		0x1 0x2 0x2 0x4 0x0 0x0 0xc0 0x4
+		0x8 0x1f4>;
+	rockchip,phy-timing = <0x48d7dd93 0x187008d8 0x121076
+		0x0 0xc3 0x6 0x2>;
+	/* Add a dummy value to cause of-platdata think this is bytes */
+	rockchip,sdram-channel = /bits/ 8 <0x2 0xa 0x3 0x2 0x2 0x0 0xe 0xe 0xff>;
+	rockchip,sdram-params = <0x20d266a4 0x5b6 2 533000000 6 9 0>;
+};
+
+&pinctrl {
+	u-boot,dm-pre-reloc;
+};
+
+&pwm1 {
+	status = "okay";
+};
+
+&uart2 {
+	u-boot,dm-pre-reloc;
+	reg-shift = <2>;
+};
+
+&sdmmc {
+	u-boot,dm-pre-reloc;
+};
+
+&emmc {
+	u-boot,dm-pre-reloc;
+};
+
+&gpio3 {
+	u-boot,dm-pre-reloc;
+};
+
+&gpio8 {
+	u-boot,dm-pre-reloc;
+};

arch/arm/dts/rk3288-fennec.dtsi

@@ -0,0 +1,421 @@
+/*
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "rk3288.dtsi"
+
+/ {
+	memory {
+		reg = <0x0 0x80000000>;
+		device_type = "memory";
+	};
+
+	ext_gmac: external-gmac-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <125000000>;
+		clock-output-names = "ext_gmac";
+	};
+
+	vcc_sys: vsys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_sys";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+};
+
+&cpu0 {
+	cpu0-supply = <&vdd_cpu>;
+};
+
+&emmc {
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	disable-wp;
+	non-removable;
+	num-slots = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_pwr &emmc_bus8>;
+	status = "okay";
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-mmc-highspeed;
+	cap-sd-highspeed;
+	card-detect-delay = <200>;
+	disable-wp;
+	num-slots = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
+	status = "okay";
+	vmmc-supply = <&vcc_sd>;
+	vqmmc-supply = <&vccio_sd>;
+};
+
+&gmac {
+	assigned-clocks = <&cru SCLK_MAC>;
+	assigned-clock-parents = <&ext_gmac>;
+	clock_in_out = "input";
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii_pins>, <&phy_rst>, <&phy_pmeb>, <&phy_int>;
+	phy-supply = <&vcc_lan>;
+	phy-mode = "rgmii";
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 10000 1000000>;
+	snps,reset-gpio = <&gpio4 8 GPIO_ACTIVE_LOW>;
+	tx_delay = <0x30>;
+	rx_delay = <0x10>;
+	status = "okay";
+};
+
+&gpu {
+	mali-supply = <&vdd_gpu>;
+	status = "okay";
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	rk808: pmic@1b {
+		compatible = "rockchip,rk808";
+		reg = <0x1b>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+		#clock-cells = <1>;
+		clock-output-names = "xin32k", "rk808-clkout2";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int &global_pwroff>;
+		rockchip,system-power-controller;
+		wakeup-source;
+
+		vcc1-supply = <&vcc_sys>;
+		vcc2-supply = <&vcc_sys>;
+		vcc3-supply = <&vcc_sys>;
+		vcc4-supply = <&vcc_sys>;
+		vcc6-supply = <&vcc_sys>;
+		vcc7-supply = <&vcc_sys>;
+		vcc8-supply = <&vcc_io>;
+		vcc9-supply = <&vcc_io>;
+		vcc10-supply = <&vcc_io>;
+		vcc11-supply = <&vcc_io>;
+		vcc12-supply = <&vcc_io>;
+		vddio-supply = <&vcc_io>;
+
+		regulators {
+			vdd_cpu: DCDC_REG1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-name = "vdd_arm";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_gpu: DCDC_REG2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1250000>;
+				regulator-name = "vdd_gpu";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1000000>;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "vcc_ddr";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_io: DCDC_REG4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc_io";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vccio_pmu: LDO_REG1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vccio_pmu";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcca_33: LDO_REG2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcca_33";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_10: LDO_REG3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-name = "vdd_10";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1000000>;
+				};
+			};
+
+			vcc_wl: LDO_REG4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc_wl";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vccio_sd: LDO_REG5 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vccio_sd";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vdd10_lcd: LDO_REG6 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-name = "vdd10_lcd";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1000000>;
+				};
+			};
+
+			vcc_18: LDO_REG7 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc_18";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcc18_lcd: LDO_REG8 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc18_lcd";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcc_sd: SWITCH_REG1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "vcc_sd";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_lan: SWITCH_REG2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "vcc_lan";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+		};
+	};
+};
+
+&pinctrl {
+	pcfg_output_high: pcfg-output-high {
+		output-high;
+	};
+
+	pcfg_output_low: pcfg-output-low {
+		output-low;
+	};
+
+	pcfg_pull_none_drv_8ma: pcfg-pull-none-drv-8ma {
+		drive-strength = <8>;
+	};
+
+	pcfg_pull_up_drv_8ma: pcfg-pull-up-drv-8ma {
+		bias-pull-up;
+		drive-strength = <8>;
+	};
+
+	gmac {
+		phy_int: phy-int {
+			rockchip,pins = <0 9 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+
+		phy_pmeb: phy-pmeb {
+			rockchip,pins = <0 8 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+
+		phy_rst: phy-rst {
+			rockchip,pins = <4 8 RK_FUNC_GPIO &pcfg_output_high>;
+		};
+	};
+
+	pmic {
+		pmic_int: pmic-int {
+			rockchip,pins = <RK_GPIO0 4 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	sdmmc {
+		sdmmc_bus4: sdmmc-bus4 {
+			rockchip,pins = <6 16 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
+					<6 17 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
+					<6 18 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
+					<6 19 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
+		};
+
+		sdmmc_clk: sdmmc-clk {
+			rockchip,pins = <6 20 RK_FUNC_1 &pcfg_pull_none_drv_8ma>;
+		};
+
+		sdmmc_cmd: sdmmc-cmd {
+			rockchip,pins = <6 21 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
+		};
+
+		sdmmc_pwr: sdmmc-pwr {
+			rockchip,pins = <7 11 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	usbphy {
+		host_drv: host-drv {
+			rockchip,pins = <0 14 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&usbphy {
+	pinctrl-names = "default";
+	pinctrl-0 = <&host_drv>;
+	vbus_drv-gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&usb_host1 {
+	status = "okay";
+};
+
+&usb_otg {
+	status = "okay";
+};
+
+&usb_hsic {
+	status = "okay";
+};
+
+&vopb {
+	status = "okay";
+};
+
+&vopb_mmu {
+	status = "okay";
+};
+
+&vopl {
+	status = "okay";
+};
+
+&vopl_mmu {
+	status = "okay";
+};
+
+&vpu {
+	status = "okay";
+};

arch/arm/dts/rk3288-miniarm.dts

@@ -0,0 +1,61 @@
+/*
+ * (C) Copyright 2016 Rockchip Electronics Co., Ltd
+ *
+ * SPDX-License-Identifier:     GPL-2.0+ X11
+ */
+
+/dts-v1/;
+#include "rk3288-miniarm.dtsi"
+
+/ {
+	model = "Miniarm-RK3288";
+	compatible = "rockchip,rk3288-miniarm", "rockchip,rk3288";
+
+	chosen {
+		stdout-path = &uart2;
+	};
+};
+
+&dmc {
+	rockchip,num-channels = <2>;
+	rockchip,pctl-timing = <0x29a 0xc8 0x1f8 0x42 0x4e 0x4 0xea 0xa
+		0x5 0x0 0xa 0x7 0x19 0x24 0xa 0x7
+		0x5 0xa 0x5 0x200 0x5 0x10 0x40 0x0
+		0x1 0x7 0x7 0x4 0xc 0x43 0x100 0x0
+		0x5 0x0>;
+	rockchip,phy-timing = <0x48f9aab4 0xea0910 0x1002c200
+		0xa60 0x40 0x10 0x0>;
+	/* Add a dummy value to cause of-platdata think this is bytes */
+	rockchip,sdram-channel = /bits/ 8 <0x1 0xa 0x3 0x2 0x1 0x0 0xf 0xf 0xff>;
+	rockchip,sdram-params = <0x30B25564 0x627 3 666000000 3 9 1>;
+};
+
+
+&pinctrl {
+	u-boot,dm-pre-reloc;
+};
+
+&pwm1 {
+	status = "okay";
+};
+
+&uart2 {
+	u-boot,dm-pre-reloc;
+	reg-shift = <2>;
+};
+
+&sdmmc {
+	u-boot,dm-pre-reloc;
+};
+
+&emmc {
+	u-boot,dm-pre-reloc;
+};
+
+&gpio3 {
+	u-boot,dm-pre-reloc;
+};
+
+&gpio8 {
+	u-boot,dm-pre-reloc;
+};

arch/arm/dts/rk3288-miniarm.dtsi

@@ -0,0 +1,533 @@
+/*
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "rk3288.dtsi"
+
+/ {
+	memory {
+		device_type = "memory";
+		reg = <0x0 0x80000000>;
+	};
+
+	ext_gmac: external-gmac-clock {
+		compatible = "fixed-clock";
+		clock-frequency = <125000000>;
+		clock-output-names = "ext_gmac";
+		#clock-cells = <0>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		autorepeat;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pwrbtn>;
+
+		button@0 {
+			gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
+			label = "GPIO Key Power";
+			linux,input-type = <1>;
+			gpio-key,wakeup = <1>;
+			debounce-interval = <100>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		pwr-led {
+			gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		act-led {
+			gpios=<&gpio2 3 GPIO_ACTIVE_LOW>;
+			linux,default-trigger="mmc0";
+		};
+	};
+
+	vcc_sys: vsys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_sys";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	/*
+	 * NOTE: vcc_sd isn't hooked up on v1.0 boards where power comes from
+	 * vcc_io directly.  Those boards won't be able to power cycle SD cards
+	 * but it shouldn't hurt to toggle this pin there anyway.
+	 */
+	vcc_sd: sdmmc-regulator {
+		compatible = "regulator-fixed";
+		gpio = <&gpio7 11 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&sdmmc_pwr>;
+		regulator-name = "vcc_sd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <100000>;
+		vin-supply = <&vcc_io>;
+	};
+};
+
+&cpu0 {
+	cpu0-supply = <&vdd_cpu>;
+};
+
+&emmc {
+	broken-cd;
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	disable-wp;
+	non-removable;
+	num-slots = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_pwr &emmc_bus8>;
+	status = "okay";
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-mmc-highspeed;
+	cap-sd-highspeed;
+	card-detect-delay = <200>;
+	disable-wp;			/* wp not hooked up */
+	num-slots = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
+	status = "okay";
+	supports-sd;
+	vmmc-supply = <&vcc_sd>;
+	vqmmc-supply = <&vccio_sd>;
+};
+
+&gpu {
+	mali-supply = <&vdd_gpu>;
+	status = "okay";
+};
+
+&gmac {
+	phy-supply = <&vcc33_lan>;
+	phy-mode = "rgmii";
+	clock_in_out = "input";
+	snps,reset-gpio = <&gpio4 7 0>;
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 10000 1000000>;
+	assigned-clocks = <&cru SCLK_MAC>;
+	assigned-clock-parents = <&ext_gmac>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii_pins>;
+	tx_delay = <0x30>;
+	rx_delay = <0x10>;
+	status = "ok";
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c5>;
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	rk808: pmic@1b {
+		compatible = "rockchip,rk808";
+		reg = <0x1b>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int &global_pwroff>;
+		rockchip,system-power-controller;
+		wakeup-source;
+		#clock-cells = <1>;
+		clock-output-names = "xin32k", "rk808-clkout2";
+
+		vcc1-supply = <&vcc_sys>;
+		vcc2-supply = <&vcc_sys>;
+		vcc3-supply = <&vcc_sys>;
+		vcc4-supply = <&vcc_sys>;
+		vcc6-supply = <&vcc_sys>;
+		vcc7-supply = <&vcc_sys>;
+		vcc8-supply = <&vcc_18>;
+		vcc9-supply = <&vcc_io>;
+		vcc10-supply = <&vcc_io>;
+		vcc11-supply = <&vcc_sys>;
+		vcc12-supply = <&vcc_io>;
+		vddio-supply = <&vcc18_ldo1>;
+
+		regulators {
+			vdd_cpu: DCDC_REG1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-name = "vdd_arm";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_gpu: DCDC_REG2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1250000>;
+				regulator-name = "vdd_gpu";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1000000>;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "vcc_ddr";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_io: DCDC_REG4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc_io";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcc18_ldo1: LDO_REG1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc18_ldo1";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcc33_mipi: LDO_REG2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc33_mipi";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_10: LDO_REG3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-name = "vdd_10";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1000000>;
+				};
+			};
+
+			vcc18_codec: LDO_REG4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc18_codec";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vccio_sd: LDO_REG5 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vccio_sd";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vdd10_lcd: LDO_REG6 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-name = "vdd10_lcd";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1000000>;
+				};
+			};
+
+			vcc_18: LDO_REG7 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc_18";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcc18_lcd: LDO_REG8 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc18_lcd";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcc33_sd: SWITCH_REG1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "vcc33_sd";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc33_lan: SWITCH_REG2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "vcc33_lan";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+		};
+	};
+};
+
+&i2c2 {
+	status = "okay";
+	headset: nau8825@1a {
+		compatible = "nuvoton,nau8825";
+		#sound-dai-cells = <0>;
+		reg = <0x1a>;
+		interrupt-parent = <&gpio6>;
+		interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
+		nuvoton,jkdet-enable = <1>;
+		nuvoton,jkdet-pull-enable = <1>;
+		nuvoton,jkdet-pull-up = <0>;
+		nuvoton,jkdet-polarity = <1>;
+		nuvoton,vref-impedance = <2>;
+		nuvoton,micbias-voltage = <6>;
+		nuvoton,sar-threshold-num = <4>;
+		nuvoton,sar-threshold = <0xa 0x14 0x26 0x73>;
+		nuvoton,sar-hysteresis = <0>;
+		nuvoton,sar-voltage = <6>;
+		nuvoton,sar-compare-time = <0>;
+		nuvoton,sar-sampling-time = <0>;
+		nuvoton,short-key-debounce = <3>;
+		nuvoton,jack-insert-debounce = <7>;
+		nuvoton,jack-eject-debounce = <7>;
+		clock-names = "mclk";
+		clocks = <&cru SCLK_I2S0_OUT>;
+	};
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&wdt {
+	status = "okay";
+};
+
+&pwm0 {
+	status = "okay";
+};
+
+&saradc {
+	vref-supply = <&vcc18_ldo1>;
+	status ="okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&uart4 {
+	status = "okay";
+};
+
+&tsadc {
+	rockchip,hw-tshut-mode = <1>; /* tshut mode 0:CRU 1:GPIO */
+	rockchip,hw-tshut-polarity = <1>; /* tshut polarity 0:LOW 1:HIGH */
+	status = "okay";
+};
+
+&usbphy {
+	status = "okay";
+};
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&usb_host1 {
+	status = "okay";
+};
+
+&usb_otg {
+	status= "okay";
+};
+
+&vopb {
+	status = "okay";
+};
+
+&vopb_mmu {
+	status = "okay";
+};
+
+&vopl {
+	status = "okay";
+};
+
+&vopl_mmu {
+	status = "okay";
+};
+
+&pinctrl {
+	pcfg_pull_none_drv_8ma: pcfg-pull-none-drv-8ma {
+		drive-strength = <8>;
+	};
+
+	pcfg_pull_up_drv_8ma: pcfg-pull-up-drv-8ma {
+		bias-pull-up;
+		drive-strength = <8>;
+	};
+
+	backlight {
+		bl_en: bl-en {
+			rockchip,pins = <7 2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	buttons {
+		pwrbtn: pwrbtn {
+			rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	eth_phy {
+		eth_phy_pwr: eth-phy-pwr {
+			rockchip,pins = <0 6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	pmic {
+		pmic_int: pmic-int {
+			rockchip,pins = <RK_GPIO0 4 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	sdmmc {
+		/*
+		 * Default drive strength isn't enough to achieve even
+		 * high-speed mode on EVB board so bump up to 8ma.
+		 */
+		sdmmc_bus4: sdmmc-bus4 {
+			rockchip,pins = <6 16 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
+					<6 17 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
+					<6 18 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
+					<6 19 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
+		};
+
+		sdmmc_clk: sdmmc-clk {
+			rockchip,pins = <6 20 RK_FUNC_1 &pcfg_pull_none_drv_8ma>;
+		};
+
+		sdmmc_cmd: sdmmc-cmd {
+			rockchip,pins = <6 21 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
+		};
+
+		sdmmc_pwr: sdmmc-pwr {
+			rockchip,pins = <7 11 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	usb {
+		host_vbus_drv: host-vbus-drv {
+			rockchip,pins = <0 14 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		pwr_3g: pwr-3g {
+			rockchip,pins = <7 8 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};

arch/arm/dts/rk3288-popmetal.dts

@@ -0,0 +1,61 @@
+/*
+ * (C) Copyright 2016 Rockchip Electronics Co., Ltd
+ *
+ * SPDX-License-Identifier:     GPL-2.0+ X11
+ */
+
+/dts-v1/;
+#include "rk3288-popmetal.dtsi"
+
+/ {
+	model = "PopMetal-RK3288";
+	compatible = "chipspark,popmetal-rk3288", "rockchip,rk3288";
+
+	chosen {
+		stdout-path = &uart2;
+	};
+};
+
+&dmc {
+	rockchip,num-channels = <2>;
+	rockchip,pctl-timing = <0x29a 0xc8 0x1f8 0x42 0x4e 0x4 0xea 0xa
+		0x5 0x0 0xa 0x7 0x19 0x24 0xa 0x7
+		0x5 0xa 0x5 0x200 0x5 0x10 0x40 0x0
+		0x1 0x7 0x7 0x4 0xc 0x43 0x100 0x0
+		0x5 0x0>;
+	rockchip,phy-timing = <0x48f9aab4 0xea0910 0x1002c200
+		0xa60 0x40 0x10 0x0>;
+	/* Add a dummy value to cause of-platdata think this is bytes */
+	rockchip,sdram-channel = /bits/ 8 <0x1 0xa 0x3 0x2 0x1 0x0 0xf 0xf 0xff>;
+	rockchip,sdram-params = <0x30B25564 0x627 3 666000000 3 9 1>;
+};
+
+
+&pinctrl {
+	u-boot,dm-pre-reloc;
+};
+
+&pwm1 {
+	status = "okay";
+};
+
+&uart2 {
+	u-boot,dm-pre-reloc;
+	reg-shift = <2>;
+};
+
+&sdmmc {
+	u-boot,dm-pre-reloc;
+};
+
+&emmc {
+	u-boot,dm-pre-reloc;
+};
+
+&gpio3 {
+	u-boot,dm-pre-reloc;
+};
+
+&gpio8 {
+	u-boot,dm-pre-reloc;
+};

arch/arm/dts/rk3288-popmetal.dtsi

@@ -0,0 +1,520 @@
+/*
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ *  Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "rk3288.dtsi"
+
+/ {
+	memory{
+		device_type = "memory";
+		reg = <0 0x80000000>;
+	};
+
+	ext_gmac: external-gmac-clock {
+		compatible = "fixed-clock";
+		clock-frequency = <125000000>;
+		clock-output-names = "ext_gmac";
+		#clock-cells = <0>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pwrbtn>;
+
+		power {
+			gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
+			label = "GPIO Key Power";
+			linux,input-type = <1>;
+			wakeup-source;
+			debounce-interval = <100>;
+		};
+	};
+
+	io_domains: io-domains {
+		compatible = "rockchip,rk3288-io-voltage-domain";
+		rockchip,grf = <&grf>;
+
+		audio-supply = <&vcca_33>;
+		bb-supply = <&vcc_io>;
+		dvp-supply = <&vcc18_dvp>;
+		flash0-supply = <&vcc_flash>;
+		flash1-supply = <&vcc_lan>;
+		gpio30-supply = <&vcc_io>;
+		gpio1830-supply = <&vcc_io>;
+		lcdc-supply = <&vcc_io>;
+		sdcard-supply = <&vccio_sd>;
+		wifi-supply = <&vccio_wl>;
+	};
+
+	ir: ir-receiver {
+		compatible = "gpio-ir-receiver";
+		gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ir_int>;
+	};
+
+	vcc_flash: flash-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_flash";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_io>;
+	};
+
+	vcc_sd: sdmmc-regulator {
+		compatible = "regulator-fixed";
+		gpio = <&gpio7 11 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&sdmmc_pwr>;
+		regulator-name = "vcc_sd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <100000>;
+		vin-supply = <&vcc_io>;
+	};
+
+	vcc_sys: vsys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_sys";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	/*
+	 * A PT5128 creates both dovdd_1v8 and vcc28_dvp, controlled
+	 * by the dvp_pwr pin.
+	 */
+	vcc18_dvp: vcc18-dvp-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc18-dvp";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc28_dvp>;
+	};
+
+	vcc28_dvp: vcc28-dvp-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 17 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&dvp_pwr>;
+		regulator-name = "vcc28_dvp";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		regulator-always-on;
+		vin-supply = <&vcc_io>;
+	};
+};
+
+&cpu0 {
+	cpu0-supply = <&vdd_cpu>;
+};
+
+&emmc {
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	disable-wp;
+	non-removable;
+	num-slots = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_pwr &emmc_bus8>;
+	vmmc-supply = <&vcc_io>;
+	vqmmc-supply = <&vcc_flash>;
+	status = "okay";
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-mmc-highspeed;
+	cap-sd-highspeed;
+	card-detect-delay = <200>;
+	disable-wp;
+	num-slots = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
+	vmmc-supply = <&vcc_sd>;
+	vqmmc-supply = <&vccio_sd>;
+	status = "okay";
+};
+
+&gmac {
+	phy-supply = <&vcc_lan>;
+	phy-mode = "rgmii";
+	clock_in_out = "input";
+	snps,reset-gpio = <&gpio4 7 0>;
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 10000 1000000>;
+	assigned-clocks = <&cru SCLK_MAC>;
+	assigned-clock-parents = <&ext_gmac>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii_pins>;
+	tx_delay = <0x30>;
+	rx_delay = <0x10>;
+	status = "ok";
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c5>;
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	rk808: pmic@1b {
+		compatible = "rockchip,rk808";
+		reg = <0x1b>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int &global_pwroff>;
+		rockchip,system-power-controller;
+		wakeup-source;
+		#clock-cells = <1>;
+		clock-output-names = "xin32k", "rk808-clkout2";
+
+		vcc1-supply = <&vcc_sys>;
+		vcc2-supply = <&vcc_sys>;
+		vcc3-supply = <&vcc_sys>;
+		vcc4-supply = <&vcc_sys>;
+		vcc6-supply = <&vcc_sys>;
+		vcc7-supply = <&vcc_sys>;
+		vcc8-supply = <&vcc_18>;
+		vcc9-supply = <&vcc_io>;
+		vcc10-supply = <&vcc_io>;
+		vcc11-supply = <&vcc_sys>;
+		vcc12-supply = <&vcc_io>;
+		vddio-supply = <&vcc_io>;
+
+		regulators {
+			vdd_cpu: DCDC_REG1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-name = "vdd_arm";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_gpu: DCDC_REG2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1250000>;
+				regulator-name = "vdd_gpu";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1000000>;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "vcc_ddr";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_io: DCDC_REG4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc_io";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcc_lan: LDO_REG1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc_lan";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vccio_sd: LDO_REG2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vccio_sd";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_10: LDO_REG3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-name = "vdd_10";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1000000>;
+				};
+			};
+
+			vcc18_lcd: LDO_REG4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc18_lcd";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			ldo5: LDO_REG5 {
+				regulator-always-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "ldo5";
+			};
+
+			vdd10_lcd: LDO_REG6 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-name = "vdd10_lcd";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1000000>;
+				};
+			};
+
+			vcc_18: LDO_REG7 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc_18";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcca_33: LDO_REG8 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcca_33";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vccio_wl: SWITCH_REG1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "vccio_wl";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_lcd: SWITCH_REG2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "vcc_lcd";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+		};
+	};
+};
+
+&i2c1 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	ak8963: ak8963@0d {
+		compatible = "asahi-kasei,ak8975";
+		reg = <0x0d>;
+		interrupt-parent = <&gpio8>;
+		interrupts = <1 IRQ_TYPE_EDGE_RISING>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&comp_int>;
+	};
+
+	l3g4200d: l3g4200d@68 {
+		compatible = "st,l3g4200d-gyro";
+		st,drdy-int-pin = <2>;
+		reg = <0x6b>;
+	};
+
+	mma8452: mma8452@1d {
+		compatible = "fsl,mma8452";
+		reg = <0x1d>;
+		interrupt-parent = <&gpio8>;
+		interrupts = <0 IRQ_TYPE_EDGE_RISING>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&gsensor_int>;
+	};
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+&i2c4 {
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&pinctrl {
+	ak8963 {
+		comp_int: comp-int {
+			rockchip,pins = <8 1 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	buttons {
+		pwrbtn: pwrbtn {
+			rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	dvp {
+		dvp_pwr: dvp-pwr {
+			rockchip,pins = <0 17 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	ir {
+		ir_int: ir-int {
+			rockchip,pins = <0 6 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	mma8452 {
+		gsensor_int: gsensor-int {
+			rockchip,pins = <8 0 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	pmic {
+		pmic_int: pmic-int {
+			rockchip,pins = <RK_GPIO0 4 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	sdmmc {
+		sdmmc_pwr: sdmmc-pwr {
+			rockchip,pins = <7 11 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&tsadc {
+	rockchip,hw-tshut-mode = <0>;
+	rockchip,hw-tshut-polarity = <0>;
+	status = "okay";
+};
+
+&vopb {
+	status = "okay";
+};
+
+&vopb_mmu {
+	status = "okay";
+};
+
+&vopl {
+	status = "okay";
+};
+
+&vopl_mmu {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&uart4 {
+	status = "okay";
+};
+
+&usbphy {
+	status = "okay";
+};

arch/arm/dts/rk3288-rock2-square.dts

@@ -192,7 +192,7 @@
 		0x5 0x0>;
 	rockchip,phy-timing = <0x48f9aab4 0xea0910 0x1002c200
 		0xa60 0x40 0x10 0x0>;
-	rockchip,sdram-channel = /bits/ 8 <0x1 0xa 0x3 0x2 0x1 0x0 0xf 0xf>;
+	rockchip,sdram-channel = /bits/ 8 <0x1 0xa 0x3 0x2 0x1 0x0 0xf 0xf 0xff>;
 	rockchip,sdram-params = <0x30B25564 0x627 3 666000000 3 9 1>;
 };
 

arch/arm/dts/rk3288-veyron.dtsi

@@ -253,7 +253,7 @@
 		0x5 0x0>;
 	rockchip,phy-timing = <0x48f9aab4 0xea0910 0x1002c200
 		0xa60 0x40 0x10 0x0>;
-	rockchip,sdram-channel = /bits/ 8 <0x1 0xa 0x3 0x2 0x1 0x0 0xf 0xf>;
+	rockchip,sdram-channel = /bits/ 8 <0x1 0xa 0x3 0x2 0x1 0x0 0xf 0xf 0xff>;
 	rockchip,sdram-params = <0x30B25564 0x627 3 666000000 3 9 1>;
 };
 

arch/arm/dts/rk3288.dtsi

@@ -454,6 +454,7 @@
 		interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&cru HCLK_OTG0>;
 		clock-names = "otg";
+		dr_mode = "otg";
 		phys = <&usbphy0>;
 		phy-names = "usb2-phy";
 		status = "disabled";

arch/arm/dts/rk3399-evb.dts

@@ -0,0 +1,108 @@
+/*
+ * (C) Copyright 2016 Rockchip Electronics Co., Ltd
+ *
+ * SPDX-License-Identifier:     GPL-2.0+
+ */
+
+/dts-v1/;
+#include <dt-bindings/pwm/pwm.h>
+#include "rk3399.dtsi"
+
+/ {
+	model = "Rockchip RK3399 Evaluation Board";
+	compatible = "rockchip,rk3399-evb", "rockchip,rk3399",
+		     "google,rk3399evb-rev2";
+
+	chosen {
+		stdout-path = &uart2;
+	};
+
+	vdd_center: vdd-center {
+		compatible = "pwm-regulator";
+		pwms = <&pwm3 0 25000 0>;
+		regulator-name = "vdd_center";
+		regulator-min-microvolt = <800000>;
+		regulator-max-microvolt = <1400000>;
+		regulator-always-on;
+		regulator-boot-on;
+		status = "okay";
+	};
+
+	vcc3v3_sys: vcc3v3-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vcc_phy: vcc-phy-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_phy";
+		regulator-always-on;
+		regulator-boot-on;
+	};
+};
+
+&emmc_phy {
+	status = "okay";
+};
+
+&pwm0 {
+	status = "okay";
+};
+
+&pwm2 {
+	status = "okay";
+};
+
+&pwm3 {
+	status = "okay";
+};
+
+&sdmmc {
+	status = "okay";
+};
+
+&sdhci {
+	bus-width = <8>;
+	mmc-hs400-1_8v;
+	mmc-hs400-enhanced-strobe;
+	non-removable;
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&usb_host0_ohci {
+	status = "okay";
+};
+
+&usb_host1_ehci {
+	status = "okay";
+};
+
+&usb_host1_ohci {
+	status = "okay";
+};
+
+&pinctrl {
+	pmic {
+		pmic_int_l: pmic-int-l {
+			rockchip,pins =
+				<1 21 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+
+		pmic_dvs2: pmic-dvs2 {
+			rockchip,pins =
+				<1 18 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+	};
+};

arch/arm/dts/sama5d2-pinfunc.h

@@ -0,0 +1,880 @@
+#define PINMUX_PIN(no, func, ioset) \
+(((no) & 0xffff) | (((func) & 0xf) << 16) | (((ioset) & 0xff) << 20))
+
+#define PIN_PA0				0
+#define PIN_PA0__GPIO			PINMUX_PIN(PIN_PA0, 0, 0)
+#define PIN_PA0__SDMMC0_CK		PINMUX_PIN(PIN_PA0, 1, 1)
+#define PIN_PA0__QSPI0_SCK		PINMUX_PIN(PIN_PA0, 2, 1)
+#define PIN_PA0__D0			PINMUX_PIN(PIN_PA0, 6, 2)
+#define PIN_PA1				1
+#define PIN_PA1__GPIO			PINMUX_PIN(PIN_PA1, 0, 0)
+#define PIN_PA1__SDMMC0_CMD		PINMUX_PIN(PIN_PA1, 1, 1)
+#define PIN_PA1__QSPI0_CS		PINMUX_PIN(PIN_PA1, 2, 1)
+#define PIN_PA1__D1			PINMUX_PIN(PIN_PA1, 6, 2)
+#define PIN_PA2				2
+#define PIN_PA2__GPIO			PINMUX_PIN(PIN_PA2, 0, 0)
+#define PIN_PA2__SDMMC0_DAT0		PINMUX_PIN(PIN_PA2, 1, 1)
+#define PIN_PA2__QSPI0_IO0		PINMUX_PIN(PIN_PA2, 2, 1)
+#define PIN_PA2__D2			PINMUX_PIN(PIN_PA2, 6, 2)
+#define PIN_PA3				3
+#define PIN_PA3__GPIO			PINMUX_PIN(PIN_PA3, 0, 0)
+#define PIN_PA3__SDMMC0_DAT1		PINMUX_PIN(PIN_PA3, 1, 1)
+#define PIN_PA3__QSPI0_IO1		PINMUX_PIN(PIN_PA3, 2, 1)
+#define PIN_PA3__D3			PINMUX_PIN(PIN_PA3, 6, 2)
+#define PIN_PA4				4
+#define PIN_PA4__GPIO			PINMUX_PIN(PIN_PA4, 0, 0)
+#define PIN_PA4__SDMMC0_DAT2		PINMUX_PIN(PIN_PA4, 1, 1)
+#define PIN_PA4__QSPI0_IO2		PINMUX_PIN(PIN_PA4, 2, 1)
+#define PIN_PA4__D4			PINMUX_PIN(PIN_PA4, 6, 2)
+#define PIN_PA5				5
+#define PIN_PA5__GPIO			PINMUX_PIN(PIN_PA5, 0, 0)
+#define PIN_PA5__SDMMC0_DAT3		PINMUX_PIN(PIN_PA5, 1, 1)
+#define PIN_PA5__QSPI0_IO3		PINMUX_PIN(PIN_PA5, 2, 1)
+#define PIN_PA5__D5			PINMUX_PIN(PIN_PA5, 6, 2)
+#define PIN_PA6				6
+#define PIN_PA6__GPIO			PINMUX_PIN(PIN_PA6, 0, 0)
+#define PIN_PA6__SDMMC0_DAT4		PINMUX_PIN(PIN_PA6, 1, 1)
+#define PIN_PA6__QSPI1_SCK		PINMUX_PIN(PIN_PA6, 2, 1)
+#define PIN_PA6__TIOA5			PINMUX_PIN(PIN_PA6, 4, 1)
+#define PIN_PA6__FLEXCOM2_IO0		PINMUX_PIN(PIN_PA6, 5, 1)
+#define PIN_PA6__D6			PINMUX_PIN(PIN_PA6, 6, 2)
+#define PIN_PA7				7
+#define PIN_PA7__GPIO			PINMUX_PIN(PIN_PA7, 0, 0)
+#define PIN_PA7__SDMMC0_DAT5		PINMUX_PIN(PIN_PA7, 1, 1)
+#define PIN_PA7__QSPI1_IO0		PINMUX_PIN(PIN_PA7, 2, 1)
+#define PIN_PA7__TIOB5			PINMUX_PIN(PIN_PA7, 4, 1)
+#define PIN_PA7__FLEXCOM2_IO1		PINMUX_PIN(PIN_PA7, 5, 1)
+#define PIN_PA7__D7			PINMUX_PIN(PIN_PA7, 6, 2)
+#define PIN_PA8				8
+#define PIN_PA8__GPIO			PINMUX_PIN(PIN_PA8, 0, 0)
+#define PIN_PA8__SDMMC0_DAT6		PINMUX_PIN(PIN_PA8, 1, 1)
+#define PIN_PA8__QSPI1_IO1		PINMUX_PIN(PIN_PA8, 2, 1)
+#define PIN_PA8__TCLK5			PINMUX_PIN(PIN_PA8, 4, 1)
+#define PIN_PA8__FLEXCOM2_IO2		PINMUX_PIN(PIN_PA8, 5, 1)
+#define PIN_PA8__NWE_NANDWE		PINMUX_PIN(PIN_PA8, 6, 2)
+#define PIN_PA9				9
+#define PIN_PA9__GPIO			PINMUX_PIN(PIN_PA9, 0, 0)
+#define PIN_PA9__SDMMC0_DAT7		PINMUX_PIN(PIN_PA9, 1, 1)
+#define PIN_PA9__QSPI1_IO2		PINMUX_PIN(PIN_PA9, 2, 1)
+#define PIN_PA9__TIOA4			PINMUX_PIN(PIN_PA9, 4, 1)
+#define PIN_PA9__FLEXCOM2_IO3		PINMUX_PIN(PIN_PA9, 5, 1)
+#define PIN_PA9__NCS3			PINMUX_PIN(PIN_PA9, 6, 2)
+#define PIN_PA10			10
+#define PIN_PA10__GPIO			PINMUX_PIN(PIN_PA10, 0, 0)
+#define PIN_PA10__SDMMC0_RSTN		PINMUX_PIN(PIN_PA10, 1, 1)
+#define PIN_PA10__QSPI1_IO3		PINMUX_PIN(PIN_PA10, 2, 1)
+#define PIN_PA10__TIOB4			PINMUX_PIN(PIN_PA10, 4, 1)
+#define PIN_PA10__FLEXCOM2_IO4		PINMUX_PIN(PIN_PA10, 5, 1)
+#define PIN_PA10__A21_NANDALE		PINMUX_PIN(PIN_PA10, 6, 2)
+#define PIN_PA11			11
+#define PIN_PA11__GPIO			PINMUX_PIN(PIN_PA11, 0, 0)
+#define PIN_PA11__SDMMC0_VDDSEL		PINMUX_PIN(PIN_PA11, 1, 1)
+#define PIN_PA11__QSPI1_CS		PINMUX_PIN(PIN_PA11, 2, 1)
+#define PIN_PA11__TCLK4			PINMUX_PIN(PIN_PA11, 4, 1)
+#define PIN_PA11__A22_NANDCLE		PINMUX_PIN(PIN_PA11, 6, 2)
+#define PIN_PA12			12
+#define PIN_PA12__GPIO			PINMUX_PIN(PIN_PA12, 0, 0)
+#define PIN_PA12__SDMMC0_WP		PINMUX_PIN(PIN_PA12, 1, 1)
+#define PIN_PA12__IRQ			PINMUX_PIN(PIN_PA12, 2, 1)
+#define PIN_PA12__NRD_NANDOE		PINMUX_PIN(PIN_PA12, 6, 2)
+#define PIN_PA13			13
+#define PIN_PA13__GPIO			PINMUX_PIN(PIN_PA13, 0, 0)
+#define PIN_PA13__SDMMC0_CD		PINMUX_PIN(PIN_PA13, 1, 1)
+#define PIN_PA13__FLEXCOM3_IO1		PINMUX_PIN(PIN_PA13, 5, 1)
+#define PIN_PA13__D8			PINMUX_PIN(PIN_PA13, 6, 2)
+#define PIN_PA14			14
+#define PIN_PA14__GPIO			PINMUX_PIN(PIN_PA14, 0, 0)
+#define PIN_PA14__SPI0_SPCK		PINMUX_PIN(PIN_PA14, 1, 1)
+#define PIN_PA14__TK1			PINMUX_PIN(PIN_PA14, 2, 1)
+#define PIN_PA14__QSPI0_SCK		PINMUX_PIN(PIN_PA14, 3, 2)
+#define PIN_PA14__I2SC1_MCK		PINMUX_PIN(PIN_PA14, 4, 2)
+#define PIN_PA14__FLEXCOM3_IO2		PINMUX_PIN(PIN_PA14, 5, 1)
+#define PIN_PA14__D9			PINMUX_PIN(PIN_PA14, 6, 2)
+#define PIN_PA15			15
+#define PIN_PA15__GPIO			PINMUX_PIN(PIN_PA15, 0, 0)
+#define PIN_PA15__SPI0_MOSI		PINMUX_PIN(PIN_PA15, 1, 1)
+#define PIN_PA15__TF1			PINMUX_PIN(PIN_PA15, 2, 1)
+#define PIN_PA15__QSPI0_CS		PINMUX_PIN(PIN_PA15, 3, 2)
+#define PIN_PA15__I2SC1_CK		PINMUX_PIN(PIN_PA15, 4, 2)
+#define PIN_PA15__FLEXCOM3_IO0		PINMUX_PIN(PIN_PA15, 5, 1)
+#define PIN_PA15__D10			PINMUX_PIN(PIN_PA15, 6, 2)
+#define PIN_PA16			16
+#define PIN_PA16__GPIO			PINMUX_PIN(PIN_PA16, 0, 0)
+#define PIN_PA16__SPI0_MISO		PINMUX_PIN(PIN_PA16, 1, 1)
+#define PIN_PA16__TD1			PINMUX_PIN(PIN_PA16, 2, 1)
+#define PIN_PA16__QSPI0_IO0		PINMUX_PIN(PIN_PA16, 3, 2)
+#define PIN_PA16__I2SC1_WS		PINMUX_PIN(PIN_PA16, 4, 2)
+#define PIN_PA16__FLEXCOM3_IO3		PINMUX_PIN(PIN_PA16, 5, 1)
+#define PIN_PA16__D11			PINMUX_PIN(PIN_PA16, 6, 2)
+#define PIN_PA17			17
+#define PIN_PA17__GPIO			PINMUX_PIN(PIN_PA17, 0, 0)
+#define PIN_PA17__SPI0_NPCS0		PINMUX_PIN(PIN_PA17, 1, 1)
+#define PIN_PA17__RD1			PINMUX_PIN(PIN_PA17, 2, 1)
+#define PIN_PA17__QSPI0_IO1		PINMUX_PIN(PIN_PA17, 3, 2)
+#define PIN_PA17__I2SC1_DI0		PINMUX_PIN(PIN_PA17, 4, 2)
+#define PIN_PA17__FLEXCOM3_IO4		PINMUX_PIN(PIN_PA17, 5, 1)
+#define PIN_PA17__D12			PINMUX_PIN(PIN_PA17, 6, 2)
+#define PIN_PA18			18
+#define PIN_PA18__GPIO			PINMUX_PIN(PIN_PA18, 0, 0)
+#define PIN_PA18__SPI0_NPCS1		PINMUX_PIN(PIN_PA18, 1, 1)
+#define PIN_PA18__RK1			PINMUX_PIN(PIN_PA18, 2, 1)
+#define PIN_PA18__QSPI0_IO2		PINMUX_PIN(PIN_PA18, 3, 2)
+#define PIN_PA18__I2SC1_DO0		PINMUX_PIN(PIN_PA18, 4, 2)
+#define PIN_PA18__SDMMC1_DAT0		PINMUX_PIN(PIN_PA18, 5, 1)
+#define PIN_PA18__D13			PINMUX_PIN(PIN_PA18, 6, 2)
+#define PIN_PA19			19
+#define PIN_PA19__GPIO			PINMUX_PIN(PIN_PA19, 0, 0)
+#define PIN_PA19__SPI0_NPCS2		PINMUX_PIN(PIN_PA19, 1, 1)
+#define PIN_PA19__RF1			PINMUX_PIN(PIN_PA19, 2, 1)
+#define PIN_PA19__QSPI0_IO3		PINMUX_PIN(PIN_PA19, 3, 2)
+#define PIN_PA19__TIOA0			PINMUX_PIN(PIN_PA19, 4, 1)
+#define PIN_PA19__SDMMC1_DAT1		PINMUX_PIN(PIN_PA19, 5, 1)
+#define PIN_PA19__D14			PINMUX_PIN(PIN_PA19, 6, 2)
+#define PIN_PA20			20
+#define PIN_PA20__GPIO			PINMUX_PIN(PIN_PA20, 0, 0)
+#define PIN_PA20__SPI0_NPCS3		PINMUX_PIN(PIN_PA20, 1, 1)
+#define PIN_PA20__TIOB0			PINMUX_PIN(PIN_PA20, 4, 1)
+#define PIN_PA20__SDMMC1_DAT2		PINMUX_PIN(PIN_PA20, 5, 1)
+#define PIN_PA20__D15			PINMUX_PIN(PIN_PA20, 6, 2)
+#define PIN_PA21			21
+#define PIN_PA21__GPIO			PINMUX_PIN(PIN_PA21, 0, 0)
+#define PIN_PA21__IRQ			PINMUX_PIN(PIN_PA21, 1, 2)
+#define PIN_PA21__PCK2			PINMUX_PIN(PIN_PA21, 2, 3)
+#define PIN_PA21__TCLK0			PINMUX_PIN(PIN_PA21, 4, 1)
+#define PIN_PA21__SDMMC1_DAT3		PINMUX_PIN(PIN_PA21, 5, 1)
+#define PIN_PA21__NANDRDY		PINMUX_PIN(PIN_PA21, 6, 2)
+#define PIN_PA22			22
+#define PIN_PA22__GPIO			PINMUX_PIN(PIN_PA22, 0, 0)
+#define PIN_PA22__FLEXCOM1_IO2		PINMUX_PIN(PIN_PA22, 1, 1)
+#define PIN_PA22__D0			PINMUX_PIN(PIN_PA22, 2, 1)
+#define PIN_PA22__TCK			PINMUX_PIN(PIN_PA22, 3, 4)
+#define PIN_PA22__SPI1_SPCK		PINMUX_PIN(PIN_PA22, 4, 2)
+#define PIN_PA22__SDMMC1_CK		PINMUX_PIN(PIN_PA22, 5, 1)
+#define PIN_PA22__QSPI0_SCK		PINMUX_PIN(PIN_PA22, 6, 3)
+#define PIN_PA23			23
+#define PIN_PA23__GPIO			PINMUX_PIN(PIN_PA23, 0, 0)
+#define PIN_PA23__FLEXCOM1_IO1		PINMUX_PIN(PIN_PA23, 1, 1)
+#define PIN_PA23__D1			PINMUX_PIN(PIN_PA23, 2, 1)
+#define PIN_PA23__TDI			PINMUX_PIN(PIN_PA23, 3, 4)
+#define PIN_PA23__SPI1_MOSI		PINMUX_PIN(PIN_PA23, 4, 2)
+#define PIN_PA23__QSPI0_CS		PINMUX_PIN(PIN_PA23, 6, 3)
+#define PIN_PA24			24
+#define PIN_PA24__GPIO			PINMUX_PIN(PIN_PA24, 0, 0)
+#define PIN_PA24__FLEXCOM1_IO0		PINMUX_PIN(PIN_PA24, 1, 1)
+#define PIN_PA24__D2			PINMUX_PIN(PIN_PA24, 2, 1)
+#define PIN_PA24__TDO			PINMUX_PIN(PIN_PA24, 3, 4)
+#define PIN_PA24__SPI1_MISO		PINMUX_PIN(PIN_PA24, 4, 2)
+#define PIN_PA24__QSPI0_IO0		PINMUX_PIN(PIN_PA24, 6, 3)
+#define PIN_PA25			25
+#define PIN_PA25__GPIO			PINMUX_PIN(PIN_PA25, 0, 0)
+#define PIN_PA25__FLEXCOM1_IO3		PINMUX_PIN(PIN_PA25, 1, 1)
+#define PIN_PA25__D3			PINMUX_PIN(PIN_PA25, 2, 1)
+#define PIN_PA25__TMS			PINMUX_PIN(PIN_PA25, 3, 4)
+#define PIN_PA25__SPI1_NPCS0		PINMUX_PIN(PIN_PA25, 4, 2)
+#define PIN_PA25__QSPI0_IO1		PINMUX_PIN(PIN_PA25, 6, 3)
+#define PIN_PA26			26
+#define PIN_PA26__GPIO			PINMUX_PIN(PIN_PA26, 0, 0)
+#define PIN_PA26__FLEXCOM1_IO4		PINMUX_PIN(PIN_PA26, 1, 1)
+#define PIN_PA26__D4			PINMUX_PIN(PIN_PA26, 2, 1)
+#define PIN_PA26__NTRST			PINMUX_PIN(PIN_PA26, 3, 4)
+#define PIN_PA26__SPI1_NPCS1		PINMUX_PIN(PIN_PA26, 4, 2)
+#define PIN_PA26__QSPI0_IO2		PINMUX_PIN(PIN_PA26, 6, 3)
+#define PIN_PA27			27
+#define PIN_PA27__GPIO			PINMUX_PIN(PIN_PA27, 0, 0)
+#define PIN_PA27__TIOA1			PINMUX_PIN(PIN_PA27, 1, 2)
+#define PIN_PA27__D5			PINMUX_PIN(PIN_PA27, 2, 1)
+#define PIN_PA27__SPI0_NPCS2		PINMUX_PIN(PIN_PA27, 3, 2)
+#define PIN_PA27__SPI1_NPCS2		PINMUX_PIN(PIN_PA27, 4, 2)
+#define PIN_PA27__SDMMC1_RSTN		PINMUX_PIN(PIN_PA27, 5, 1)
+#define PIN_PA27__QSPI0_IO3		PINMUX_PIN(PIN_PA27, 6, 3)
+#define PIN_PA28			28
+#define PIN_PA28__GPIO			PINMUX_PIN(PIN_PA28, 0, 0)
+#define PIN_PA28__TIOB1			PINMUX_PIN(PIN_PA28, 1, 2)
+#define PIN_PA28__D6			PINMUX_PIN(PIN_PA28, 2, 1)
+#define PIN_PA28__SPI0_NPCS3		PINMUX_PIN(PIN_PA28, 3, 2)
+#define PIN_PA28__SPI1_NPCS3		PINMUX_PIN(PIN_PA28, 4, 2)
+#define PIN_PA28__SDMMC1_CMD		PINMUX_PIN(PIN_PA28, 5, 1)
+#define PIN_PA28__CLASSD_L0		PINMUX_PIN(PIN_PA28, 6, 1)
+#define PIN_PA29			29
+#define PIN_PA29__GPIO			PINMUX_PIN(PIN_PA29, 0, 0)
+#define PIN_PA29__TCLK1			PINMUX_PIN(PIN_PA29, 1, 2)
+#define PIN_PA29__D7			PINMUX_PIN(PIN_PA29, 2, 1)
+#define PIN_PA29__SPI0_NPCS1		PINMUX_PIN(PIN_PA29, 3, 2)
+#define PIN_PA29__SDMMC1_WP		PINMUX_PIN(PIN_PA29, 5, 1)
+#define PIN_PA29__CLASSD_L1		PINMUX_PIN(PIN_PA29, 6, 1)
+#define PIN_PA30			30
+#define PIN_PA30__GPIO			PINMUX_PIN(PIN_PA30, 0, 0)
+#define PIN_PA30__NWE_NANDWE		PINMUX_PIN(PIN_PA30, 2, 1)
+#define PIN_PA30__SPI0_NPCS0		PINMUX_PIN(PIN_PA30, 3, 2)
+#define PIN_PA30__PWMH0			PINMUX_PIN(PIN_PA30, 4, 1)
+#define PIN_PA30__SDMMC1_CD		PINMUX_PIN(PIN_PA30, 5, 1)
+#define PIN_PA30__CLASSD_L2		PINMUX_PIN(PIN_PA30, 6, 1)
+#define PIN_PA31			31
+#define PIN_PA31__GPIO			PINMUX_PIN(PIN_PA31, 0, 0)
+#define PIN_PA31__NCS3			PINMUX_PIN(PIN_PA31, 2, 1)
+#define PIN_PA31__SPI0_MISO		PINMUX_PIN(PIN_PA31, 3, 2)
+#define PIN_PA31__PWML0			PINMUX_PIN(PIN_PA31, 4, 1)
+#define PIN_PA31__CLASSD_L3		PINMUX_PIN(PIN_PA31, 6, 1)
+#define PIN_PB0				32
+#define PIN_PB0__GPIO			PINMUX_PIN(PIN_PB0, 0, 0)
+#define PIN_PB0__A21_NANDALE		PINMUX_PIN(PIN_PB0, 2, 1)
+#define PIN_PB0__SPI0_MOSI		PINMUX_PIN(PIN_PB0, 3, 2)
+#define PIN_PB0__PWMH1			PINMUX_PIN(PIN_PB0, 4, 1)
+#define PIN_PB1				33
+#define PIN_PB1__GPIO			PINMUX_PIN(PIN_PB1, 0, 0)
+#define PIN_PB1__A22_NANDCLE		PINMUX_PIN(PIN_PB1, 2, 1)
+#define PIN_PB1__SPI0_SPCK		PINMUX_PIN(PIN_PB1, 3, 2)
+#define PIN_PB1__PWML1			PINMUX_PIN(PIN_PB1, 4, 1)
+#define PIN_PB1__CLASSD_R0		PINMUX_PIN(PIN_PB1, 6, 1)
+#define PIN_PB2				34
+#define PIN_PB2__GPIO			PINMUX_PIN(PIN_PB2, 0, 0)
+#define PIN_PB2__NRD_NANDOE		PINMUX_PIN(PIN_PB2, 2, 1)
+#define PIN_PB2__PWMFI0			PINMUX_PIN(PIN_PB2, 4, 1)
+#define PIN_PB2__CLASSD_R1		PINMUX_PIN(PIN_PB2, 6, 1)
+#define PIN_PB3				35
+#define PIN_PB3__GPIO			PINMUX_PIN(PIN_PB3, 0, 0)
+#define PIN_PB3__URXD4			PINMUX_PIN(PIN_PB3, 1, 1)
+#define PIN_PB3__D8			PINMUX_PIN(PIN_PB3, 2, 1)
+#define PIN_PB3__IRQ			PINMUX_PIN(PIN_PB3, 3, 3)
+#define PIN_PB3__PWMEXTRG0		PINMUX_PIN(PIN_PB3, 4, 1)
+#define PIN_PB3__CLASSD_R2		PINMUX_PIN(PIN_PB3, 6, 1)
+#define PIN_PB4				36
+#define PIN_PB4__GPIO			PINMUX_PIN(PIN_PB4, 0, 0)
+#define PIN_PB4__UTXD4			PINMUX_PIN(PIN_PB4, 1, 1)
+#define PIN_PB4__D9			PINMUX_PIN(PIN_PB4, 2, 1)
+#define PIN_PB4__FIQ			PINMUX_PIN(PIN_PB4, 3, 4)
+#define PIN_PB4__CLASSD_R3		PINMUX_PIN(PIN_PB4, 6, 1)
+#define PIN_PB5				37
+#define PIN_PB5__GPIO			PINMUX_PIN(PIN_PB5, 0, 0)
+#define PIN_PB5__TCLK2			PINMUX_PIN(PIN_PB5, 1, 1)
+#define PIN_PB5__D10			PINMUX_PIN(PIN_PB5, 2, 1)
+#define PIN_PB5__PWMH2			PINMUX_PIN(PIN_PB5, 3, 1)
+#define PIN_PB5__QSPI1_SCK		PINMUX_PIN(PIN_PB5, 4, 2)
+#define PIN_PB5__GTSUCOMP		PINMUX_PIN(PIN_PB5, 6, 3)
+#define PIN_PB6				38
+#define PIN_PB6__GPIO			PINMUX_PIN(PIN_PB6, 0, 0)
+#define PIN_PB6__TIOA2			PINMUX_PIN(PIN_PB6, 1, 1)
+#define PIN_PB6__D11			PINMUX_PIN(PIN_PB6, 2, 1)
+#define PIN_PB6__PWML2			PINMUX_PIN(PIN_PB6, 3, 1)
+#define PIN_PB6__QSPI1_CS		PINMUX_PIN(PIN_PB6, 4, 2)
+#define PIN_PB6__GTXER			PINMUX_PIN(PIN_PB6, 6, 3)
+#define PIN_PB7				39
+#define PIN_PB7__GPIO			PINMUX_PIN(PIN_PB7, 0, 0)
+#define PIN_PB7__TIOB2			PINMUX_PIN(PIN_PB7, 1, 1)
+#define PIN_PB7__D12			PINMUX_PIN(PIN_PB7, 2, 1)
+#define PIN_PB7__PWMH3			PINMUX_PIN(PIN_PB7, 3, 1)
+#define PIN_PB7__QSPI1_IO0		PINMUX_PIN(PIN_PB7, 4, 2)
+#define PIN_PB7__GRXCK			PINMUX_PIN(PIN_PB7, 6, 3)
+#define PIN_PB8				40
+#define PIN_PB8__GPIO			PINMUX_PIN(PIN_PB8, 0, 0)
+#define PIN_PB8__TCLK3			PINMUX_PIN(PIN_PB8, 1, 1)
+#define PIN_PB8__D13			PINMUX_PIN(PIN_PB8, 2, 1)
+#define PIN_PB8__PWML3			PINMUX_PIN(PIN_PB8, 3, 1)
+#define PIN_PB8__QSPI1_IO1		PINMUX_PIN(PIN_PB8, 4, 2)
+#define PIN_PB8__GCRS			PINMUX_PIN(PIN_PB8, 6, 3)
+#define PIN_PB9				41
+#define PIN_PB9__GPIO			PINMUX_PIN(PIN_PB9, 0, 0)
+#define PIN_PB9__TIOA3			PINMUX_PIN(PIN_PB9, 1, 1)
+#define PIN_PB9__D14			PINMUX_PIN(PIN_PB9, 2, 1)
+#define PIN_PB9__PWMFI1			PINMUX_PIN(PIN_PB9, 3, 1)
+#define PIN_PB9__QSPI1_IO2		PINMUX_PIN(PIN_PB9, 4, 2)
+#define PIN_PB9__GCOL			PINMUX_PIN(PIN_PB9, 6, 3)
+#define PIN_PB10			42
+#define PIN_PB10__GPIO			PINMUX_PIN(PIN_PB10, 0, 0)
+#define PIN_PB10__TIOB3			PINMUX_PIN(PIN_PB10, 1, 1)
+#define PIN_PB10__D15			PINMUX_PIN(PIN_PB10, 2, 1)
+#define PIN_PB10__PWMEXTRG1		PINMUX_PIN(PIN_PB10, 3, 1)
+#define PIN_PB10__QSPI1_IO3		PINMUX_PIN(PIN_PB10, 4, 2)
+#define PIN_PB10__GRX2			PINMUX_PIN(PIN_PB10, 6, 3)
+#define PIN_PB11			43
+#define PIN_PB11__GPIO			PINMUX_PIN(PIN_PB11, 0, 0)
+#define PIN_PB11__LCDDAT0		PINMUX_PIN(PIN_PB11, 1, 1)
+#define PIN_PB11__A0_NBS0		PINMUX_PIN(PIN_PB11, 2, 1)
+#define PIN_PB11__URXD3			PINMUX_PIN(PIN_PB11, 3, 3)
+#define PIN_PB11__PDMIC_DAT		PINMUX_PIN(PIN_PB11, 4, 2)
+#define PIN_PB11__GRX3			PINMUX_PIN(PIN_PB11, 6, 3)
+#define PIN_PB12			44
+#define PIN_PB12__GPIO			PINMUX_PIN(PIN_PB12, 0, 0)
+#define PIN_PB12__LCDDAT1		PINMUX_PIN(PIN_PB12, 1, 1)
+#define PIN_PB12__A1			PINMUX_PIN(PIN_PB12, 2, 1)
+#define PIN_PB12__UTXD3			PINMUX_PIN(PIN_PB12, 3, 3)
+#define PIN_PB12__PDMIC_CLK		PINMUX_PIN(PIN_PB12, 4, 2)
+#define PIN_PB12__GTX2			PINMUX_PIN(PIN_PB12, 6, 3)
+#define PIN_PB13			45
+#define PIN_PB13__GPIO			PINMUX_PIN(PIN_PB13, 0, 0)
+#define PIN_PB13__LCDDAT2		PINMUX_PIN(PIN_PB13, 1, 1)
+#define PIN_PB13__A2			PINMUX_PIN(PIN_PB13, 2, 1)
+#define PIN_PB13__PCK1			PINMUX_PIN(PIN_PB13, 3, 3)
+#define PIN_PB13__GTX3			PINMUX_PIN(PIN_PB13, 6, 3)
+#define PIN_PB14			46
+#define PIN_PB14__GPIO			PINMUX_PIN(PIN_PB14, 0, 0)
+#define PIN_PB14__LCDDAT3		PINMUX_PIN(PIN_PB14, 1, 1)
+#define PIN_PB14__A3			PINMUX_PIN(PIN_PB14, 2, 1)
+#define PIN_PB14__TK1			PINMUX_PIN(PIN_PB14, 3, 2)
+#define PIN_PB14__I2SC1_MCK		PINMUX_PIN(PIN_PB14, 4, 1)
+#define PIN_PB14__QSPI1_SCK		PINMUX_PIN(PIN_PB14, 5, 3)
+#define PIN_PB14__GTXCK			PINMUX_PIN(PIN_PB14, 6, 3)
+#define PIN_PB15			47
+#define PIN_PB15__GPIO			PINMUX_PIN(PIN_PB15, 0, 0)
+#define PIN_PB15__LCDDAT4		PINMUX_PIN(PIN_PB15, 1, 1)
+#define PIN_PB15__A4			PINMUX_PIN(PIN_PB15, 2, 1)
+#define PIN_PB15__TF1			PINMUX_PIN(PIN_PB15, 3, 2)
+#define PIN_PB15__I2SC1_CK		PINMUX_PIN(PIN_PB15, 4, 1)
+#define PIN_PB15__QSPI1_CS		PINMUX_PIN(PIN_PB15, 5, 3)
+#define PIN_PB15__GTXEN			PINMUX_PIN(PIN_PB15, 6, 3)
+#define PIN_PB16			48
+#define PIN_PB16__GPIO			PINMUX_PIN(PIN_PB16, 0, 0)
+#define PIN_PB16__LCDDAT5		PINMUX_PIN(PIN_PB16, 1, 1)
+#define PIN_PB16__A5			PINMUX_PIN(PIN_PB16, 2, 1)
+#define PIN_PB16__TD1			PINMUX_PIN(PIN_PB16, 3, 2)
+#define PIN_PB16__I2SC1_WS		PINMUX_PIN(PIN_PB16, 4, 1)
+#define PIN_PB16__QSPI1_IO0		PINMUX_PIN(PIN_PB16, 5, 3)
+#define PIN_PB16__GRXDV			PINMUX_PIN(PIN_PB16, 6, 3)
+#define PIN_PB17			49
+#define PIN_PB17__GPIO			PINMUX_PIN(PIN_PB17, 0, 0)
+#define PIN_PB17__LCDDAT6		PINMUX_PIN(PIN_PB17, 1, 1)
+#define PIN_PB17__A6			PINMUX_PIN(PIN_PB17, 2, 1)
+#define PIN_PB17__RD1			PINMUX_PIN(PIN_PB17, 3, 2)
+#define PIN_PB17__I2SC1_DI0		PINMUX_PIN(PIN_PB17, 4, 1)
+#define PIN_PB17__QSPI1_IO1		PINMUX_PIN(PIN_PB17, 5, 3)
+#define PIN_PB17__GRXER			PINMUX_PIN(PIN_PB17, 6, 3)
+#define PIN_PB18			50
+#define PIN_PB18__GPIO			PINMUX_PIN(PIN_PB18, 0, 0)
+#define PIN_PB18__LCDDAT7		PINMUX_PIN(PIN_PB18, 1, 1)
+#define PIN_PB18__A7			PINMUX_PIN(PIN_PB18, 2, 1)
+#define PIN_PB18__RK1			PINMUX_PIN(PIN_PB18, 3, 2)
+#define PIN_PB18__I2SC1_DO0		PINMUX_PIN(PIN_PB18, 4, 1)
+#define PIN_PB18__QSPI1_IO2		PINMUX_PIN(PIN_PB18, 5, 3)
+#define PIN_PB18__GRX0			PINMUX_PIN(PIN_PB18, 6, 3)
+#define PIN_PB19			51
+#define PIN_PB19__GPIO			PINMUX_PIN(PIN_PB19, 0, 0)
+#define PIN_PB19__LCDDAT8		PINMUX_PIN(PIN_PB19, 1, 1)
+#define PIN_PB19__A8			PINMUX_PIN(PIN_PB19, 2, 1)
+#define PIN_PB19__RF1			PINMUX_PIN(PIN_PB19, 3, 2)
+#define PIN_PB19__TIOA3			PINMUX_PIN(PIN_PB19, 4, 2)
+#define PIN_PB19__QSPI1_IO3		PINMUX_PIN(PIN_PB19, 5, 3)
+#define PIN_PB19__GRX1			PINMUX_PIN(PIN_PB19, 6, 3)
+#define PIN_PB20			52
+#define PIN_PB20__GPIO			PINMUX_PIN(PIN_PB20, 0, 0)
+#define PIN_PB20__LCDDAT9		PINMUX_PIN(PIN_PB20, 1, 1)
+#define PIN_PB20__A9			PINMUX_PIN(PIN_PB20, 2, 1)
+#define PIN_PB20__TK0			PINMUX_PIN(PIN_PB20, 3, 1)
+#define PIN_PB20__TIOB3			PINMUX_PIN(PIN_PB20, 4, 2)
+#define PIN_PB20__PCK1			PINMUX_PIN(PIN_PB20, 5, 4)
+#define PIN_PB20__GTX0			PINMUX_PIN(PIN_PB20, 6, 3)
+#define PIN_PB21			53
+#define PIN_PB21__GPIO			PINMUX_PIN(PIN_PB21, 0, 0)
+#define PIN_PB21__LCDDAT10		PINMUX_PIN(PIN_PB21, 1, 1)
+#define PIN_PB21__A10			PINMUX_PIN(PIN_PB21, 2, 1)
+#define PIN_PB21__TF0			PINMUX_PIN(PIN_PB21, 3, 1)
+#define PIN_PB21__TCLK3			PINMUX_PIN(PIN_PB21, 4, 2)
+#define PIN_PB21__FLEXCOM3_IO2		PINMUX_PIN(PIN_PB21, 5, 3)
+#define PIN_PB21__GTX1			PINMUX_PIN(PIN_PB21, 6, 3)
+#define PIN_PB22			54
+#define PIN_PB22__GPIO			PINMUX_PIN(PIN_PB22, 0, 0)
+#define PIN_PB22__LCDDAT11		PINMUX_PIN(PIN_PB22, 1, 1)
+#define PIN_PB22__A11			PINMUX_PIN(PIN_PB22, 2, 1)
+#define PIN_PB22__TDO			PINMUX_PIN(PIN_PB22, 3, 1)
+#define PIN_PB22__TIOA2			PINMUX_PIN(PIN_PB22, 4, 2)
+#define PIN_PB22__FLEXCOM3_IO1		PINMUX_PIN(PIN_PB22, 5, 3)
+#define PIN_PB22__GMDC			PINMUX_PIN(PIN_PB22, 6, 3)
+#define PIN_PB23			55
+#define PIN_PB23__GPIO			PINMUX_PIN(PIN_PB23, 0, 0)
+#define PIN_PB23__LCDDAT12		PINMUX_PIN(PIN_PB23, 1, 1)
+#define PIN_PB23__A12			PINMUX_PIN(PIN_PB23, 2, 1)
+#define PIN_PB23__RD0			PINMUX_PIN(PIN_PB23, 3, 1)
+#define PIN_PB23__TIOB2			PINMUX_PIN(PIN_PB23, 4, 2)
+#define PIN_PB23__FLEXCOM3_IO0		PINMUX_PIN(PIN_PB23, 5, 3)
+#define PIN_PB23__GMDIO			PINMUX_PIN(PIN_PB23, 6, 3)
+#define PIN_PB24			56
+#define PIN_PB24__GPIO			PINMUX_PIN(PIN_PB24, 0, 0)
+#define PIN_PB24__LCDDAT13		PINMUX_PIN(PIN_PB24, 1, 1)
+#define PIN_PB24__A13			PINMUX_PIN(PIN_PB24, 2, 1)
+#define PIN_PB24__RK0			PINMUX_PIN(PIN_PB24, 3, 1)
+#define PIN_PB24__TCLK2			PINMUX_PIN(PIN_PB24, 4, 2)
+#define PIN_PB24__FLEXCOM3_IO3		PINMUX_PIN(PIN_PB24, 5, 3)
+#define PIN_PB24__ISC_D10		PINMUX_PIN(PIN_PB24, 6, 3)
+#define PIN_PB25			57
+#define PIN_PB25__GPIO			PINMUX_PIN(PIN_PB25, 0, 0)
+#define PIN_PB25__LCDDAT14		PINMUX_PIN(PIN_PB25, 1, 1)
+#define PIN_PB25__A14			PINMUX_PIN(PIN_PB25, 2, 1)
+#define PIN_PB25__RF0			PINMUX_PIN(PIN_PB25, 3, 1)
+#define PIN_PB25__FLEXCOM3_IO4		PINMUX_PIN(PIN_PB25, 5, 3)
+#define PIN_PB25__ISC_D11		PINMUX_PIN(PIN_PB25, 6, 3)
+#define PIN_PB26			58
+#define PIN_PB26__GPIO			PINMUX_PIN(PIN_PB26, 0, 0)
+#define PIN_PB26__LCDDAT15		PINMUX_PIN(PIN_PB26, 1, 1)
+#define PIN_PB26__A15			PINMUX_PIN(PIN_PB26, 2, 1)
+#define PIN_PB26__URXD0			PINMUX_PIN(PIN_PB26, 3, 1)
+#define PIN_PB26__PDMIC_DAT		PINMUX_PIN(PIN_PB26, 4, 1)
+#define PIN_PB26__ISC_D0		PINMUX_PIN(PIN_PB26, 6, 3)
+#define PIN_PB27			59
+#define PIN_PB27__GPIO			PINMUX_PIN(PIN_PB27, 0, 0)
+#define PIN_PB27__LCDDAT16		PINMUX_PIN(PIN_PB27, 1, 1)
+#define PIN_PB27__A16			PINMUX_PIN(PIN_PB27, 2, 1)
+#define PIN_PB27__UTXD0			PINMUX_PIN(PIN_PB27, 3, 1)
+#define PIN_PB27__PDMIC_CLK		PINMUX_PIN(PIN_PB27, 4, 1)
+#define PIN_PB27__ISC_D1		PINMUX_PIN(PIN_PB27, 6, 3)
+#define PIN_PB28			60
+#define PIN_PB28__GPIO			PINMUX_PIN(PIN_PB28, 0, 0)
+#define PIN_PB28__LCDDAT17		PINMUX_PIN(PIN_PB28, 1, 1)
+#define PIN_PB28__A17			PINMUX_PIN(PIN_PB28, 2, 1)
+#define PIN_PB28__FLEXCOM0_IO0		PINMUX_PIN(PIN_PB28, 3, 1)
+#define PIN_PB28__TIOA5			PINMUX_PIN(PIN_PB28, 4, 2)
+#define PIN_PB28__ISC_D2		PINMUX_PIN(PIN_PB28, 6, 3)
+#define PIN_PB29			61
+#define PIN_PB29__GPIO			PINMUX_PIN(PIN_PB29, 0, 0)
+#define PIN_PB29__LCDDAT18		PINMUX_PIN(PIN_PB29, 1, 1)
+#define PIN_PB29__A18			PINMUX_PIN(PIN_PB29, 2, 1)
+#define PIN_PB29__FLEXCOM0_IO1		PINMUX_PIN(PIN_PB29, 3, 1)
+#define PIN_PB29__TIOB5			PINMUX_PIN(PIN_PB29, 4, 2)
+#define PIN_PB29__ISC_D3		PINMUX_PIN(PIN_PB29, 7, 3)
+#define PIN_PB30			62
+#define PIN_PB30__GPIO			PINMUX_PIN(PIN_PB30, 0, 0)
+#define PIN_PB30__LCDDAT19		PINMUX_PIN(PIN_PB30, 1, 1)
+#define PIN_PB30__A19			PINMUX_PIN(PIN_PB30, 2, 1)
+#define PIN_PB30__FLEXCOM0_IO2		PINMUX_PIN(PIN_PB30, 3, 1)
+#define PIN_PB30__TCLK5			PINMUX_PIN(PIN_PB30, 4, 2)
+#define PIN_PB30__ISC_D4		PINMUX_PIN(PIN_PB30, 6, 3)
+#define PIN_PB31			63
+#define PIN_PB31__GPIO			PINMUX_PIN(PIN_PB31, 0, 0)
+#define PIN_PB31__LCDDAT20		PINMUX_PIN(PIN_PB31, 1, 1)
+#define PIN_PB31__A20			PINMUX_PIN(PIN_PB31, 2, 1)
+#define PIN_PB31__FLEXCOM0_IO3		PINMUX_PIN(PIN_PB31, 3, 1)
+#define PIN_PB31__TWD0			PINMUX_PIN(PIN_PB31, 4, 1)
+#define PIN_PB31__ISC_D5		PINMUX_PIN(PIN_PB31, 6, 3)
+#define PIN_PC0				64
+#define PIN_PC0__GPIO			PINMUX_PIN(PIN_PC0, 0, 0)
+#define PIN_PC0__LCDDAT21		PINMUX_PIN(PIN_PC0, 1, 1)
+#define PIN_PC0__A23			PINMUX_PIN(PIN_PC0, 2, 1)
+#define PIN_PC0__FLEXCOM0_IO4		PINMUX_PIN(PIN_PC0, 3, 1)
+#define PIN_PC0__TWCK0			PINMUX_PIN(PIN_PC0, 4, 1)
+#define PIN_PC0__ISC_D6			PINMUX_PIN(PIN_PC0, 6, 3)
+#define PIN_PC1				65
+#define PIN_PC1__GPIO			PINMUX_PIN(PIN_PC1, 0, 0)
+#define PIN_PC1__LCDDAT22		PINMUX_PIN(PIN_PC1, 1, 1)
+#define PIN_PC1__A24			PINMUX_PIN(PIN_PC1, 2, 1)
+#define PIN_PC1__CANTX0			PINMUX_PIN(PIN_PC1, 3, 1)
+#define PIN_PC1__SPI1_SPCK		PINMUX_PIN(PIN_PC1, 4, 1)
+#define PIN_PC1__I2SC0_CK		PINMUX_PIN(PIN_PC1, 5, 1)
+#define PIN_PC1__ISC_D7			PINMUX_PIN(PIN_PC1, 6, 3)
+#define PIN_PC2				66
+#define PIN_PC2__GPIO			PINMUX_PIN(PIN_PC2, 0, 0)
+#define PIN_PC2__LCDDAT23		PINMUX_PIN(PIN_PC2, 1, 1)
+#define PIN_PC2__A25			PINMUX_PIN(PIN_PC2, 2, 1)
+#define PIN_PC2__CANRX0			PINMUX_PIN(PIN_PC2, 3, 1)
+#define PIN_PC2__SPI1_MOSI		PINMUX_PIN(PIN_PC2, 4, 1)
+#define PIN_PC2__I2SC0_MCK		PINMUX_PIN(PIN_PC2, 5, 1)
+#define PIN_PC2__ISC_D8			PINMUX_PIN(PIN_PC2, 6, 3)
+#define PIN_PC3				67
+#define PIN_PC3__GPIO			PINMUX_PIN(PIN_PC3, 0, 0)
+#define PIN_PC3__LCDPWM			PINMUX_PIN(PIN_PC3, 1, 1)
+#define PIN_PC3__NWAIT			PINMUX_PIN(PIN_PC3, 2, 1)
+#define PIN_PC3__TIOA1			PINMUX_PIN(PIN_PC3, 3, 1)
+#define PIN_PC3__SPI1_MISO		PINMUX_PIN(PIN_PC3, 4, 1)
+#define PIN_PC3__I2SC0_WS		PINMUX_PIN(PIN_PC3, 5, 1)
+#define PIN_PC3__ISC_D9			PINMUX_PIN(PIN_PC3, 6, 3)
+#define PIN_PC4				68
+#define PIN_PC4__GPIO			PINMUX_PIN(PIN_PC4, 0, 0)
+#define PIN_PC4__LCDDISP		PINMUX_PIN(PIN_PC4, 1, 1)
+#define PIN_PC4__NWR1_NBS1		PINMUX_PIN(PIN_PC4, 2, 1)
+#define PIN_PC4__TIOB1			PINMUX_PIN(PIN_PC4, 3, 1)
+#define PIN_PC4__SPI1_NPCS0		PINMUX_PIN(PIN_PC4, 4, 1)
+#define PIN_PC4__I2SC0_DI0		PINMUX_PIN(PIN_PC4, 5, 1)
+#define PIN_PC4__ISC_PCK		PINMUX_PIN(PIN_PC4, 6, 3)
+#define PIN_PC5				69
+#define PIN_PC5__GPIO			PINMUX_PIN(PIN_PC5, 0, 0)
+#define PIN_PC5__LCDVSYNC		PINMUX_PIN(PIN_PC5, 1, 1)
+#define PIN_PC5__NCS0			PINMUX_PIN(PIN_PC5, 2, 1)
+#define PIN_PC5__TCLK1			PINMUX_PIN(PIN_PC5, 3, 1)
+#define PIN_PC5__SPI1_NPCS1		PINMUX_PIN(PIN_PC5, 4, 1)
+#define PIN_PC5__I2SC0_DO0		PINMUX_PIN(PIN_PC5, 5, 1)
+#define PIN_PC5__ISC_VSYNC		PINMUX_PIN(PIN_PC5, 6, 3)
+#define PIN_PC6				70
+#define PIN_PC6__GPIO			PINMUX_PIN(PIN_PC6, 0, 0)
+#define PIN_PC6__LCDHSYNC		PINMUX_PIN(PIN_PC6, 1, 1)
+#define PIN_PC6__NCS1			PINMUX_PIN(PIN_PC6, 2, 1)
+#define PIN_PC6__TWD1			PINMUX_PIN(PIN_PC6, 3, 1)
+#define PIN_PC6__SPI1_NPCS2		PINMUX_PIN(PIN_PC6, 4, 1)
+#define PIN_PC6__ISC_HSYNC		PINMUX_PIN(PIN_PC6, 6, 3)
+#define PIN_PC7				71
+#define PIN_PC7__GPIO			PINMUX_PIN(PIN_PC7, 0, 0)
+#define PIN_PC7__LCDPCK			PINMUX_PIN(PIN_PC7, 1, 1)
+#define PIN_PC7__NCS2			PINMUX_PIN(PIN_PC7, 2, 1)
+#define PIN_PC7__TWCK1			PINMUX_PIN(PIN_PC7, 3, 1)
+#define PIN_PC7__SPI1_NPCS3		PINMUX_PIN(PIN_PC7, 4, 1)
+#define PIN_PC7__URXD1			PINMUX_PIN(PIN_PC7, 5, 2)
+#define PIN_PC7__ISC_MCK		PINMUX_PIN(PIN_PC7, 6, 3)
+#define PIN_PC8				72
+#define PIN_PC8__GPIO			PINMUX_PIN(PIN_PC8, 0, 0)
+#define PIN_PC8__LCDDEN			PINMUX_PIN(PIN_PC8, 1, 1)
+#define PIN_PC8__NANDRDY		PINMUX_PIN(PIN_PC8, 2, 1)
+#define PIN_PC8__FIQ			PINMUX_PIN(PIN_PC8, 3, 1)
+#define PIN_PC8__PCK0			PINMUX_PIN(PIN_PC8, 4, 3)
+#define PIN_PC8__UTXD1			PINMUX_PIN(PIN_PC8, 5, 2)
+#define PIN_PC8__ISC_FIELD		PINMUX_PIN(PIN_PC8, 6, 3)
+#define PIN_PC9				73
+#define PIN_PC9__GPIO			PINMUX_PIN(PIN_PC9, 0, 0)
+#define PIN_PC9__FIQ			PINMUX_PIN(PIN_PC9, 1, 3)
+#define PIN_PC9__GTSUCOMP		PINMUX_PIN(PIN_PC9, 2, 1)
+#define PIN_PC9__ISC_D0			PINMUX_PIN(PIN_PC9, 2, 1)
+#define PIN_PC9__TIOA4			PINMUX_PIN(PIN_PC9, 4, 2)
+#define PIN_PC10			74
+#define PIN_PC10__GPIO			PINMUX_PIN(PIN_PC10, 0, 0)
+#define PIN_PC10__LCDDAT2		PINMUX_PIN(PIN_PC10, 1, 2)
+#define PIN_PC10__GTXCK			PINMUX_PIN(PIN_PC10, 2, 1)
+#define PIN_PC10__ISC_D1		PINMUX_PIN(PIN_PC10, 3, 1)
+#define PIN_PC10__TIOB4			PINMUX_PIN(PIN_PC10, 4, 2)
+#define PIN_PC10__CANTX0		PINMUX_PIN(PIN_PC10, 5, 2)
+#define PIN_PC11			75
+#define PIN_PC11__GPIO			PINMUX_PIN(PIN_PC11, 0, 0)
+#define PIN_PC11__LCDDAT3		PINMUX_PIN(PIN_PC11, 1, 2)
+#define PIN_PC11__GTXEN			PINMUX_PIN(PIN_PC11, 2, 1)
+#define PIN_PC11__ISC_D2		PINMUX_PIN(PIN_PC11, 3, 1)
+#define PIN_PC11__TCLK4			PINMUX_PIN(PIN_PC11, 4, 2)
+#define PIN_PC11__CANRX0		PINMUX_PIN(PIN_PC11, 5, 2)
+#define PIN_PC11__A0_NBS0		PINMUX_PIN(PIN_PC11, 6, 2)
+#define PIN_PC12			76
+#define PIN_PC12__GPIO			PINMUX_PIN(PIN_PC12, 0, 0)
+#define PIN_PC12__LCDDAT4		PINMUX_PIN(PIN_PC12, 1, 2)
+#define PIN_PC12__GRXDV			PINMUX_PIN(PIN_PC12, 2, 1)
+#define PIN_PC12__ISC_D3		PINMUX_PIN(PIN_PC12, 3, 1)
+#define PIN_PC12__URXD3			PINMUX_PIN(PIN_PC12, 4, 1)
+#define PIN_PC12__TK0			PINMUX_PIN(PIN_PC12, 5, 2)
+#define PIN_PC12__A1			PINMUX_PIN(PIN_PC12, 6, 2)
+#define PIN_PC13			77
+#define PIN_PC13__GPIO			PINMUX_PIN(PIN_PC13, 0, 0)
+#define PIN_PC13__LCDDAT5		PINMUX_PIN(PIN_PC13, 1, 2)
+#define PIN_PC13__GRXER			PINMUX_PIN(PIN_PC13, 2, 1)
+#define PIN_PC13__ISC_D4		PINMUX_PIN(PIN_PC13, 3, 1)
+#define PIN_PC13__UTXD3			PINMUX_PIN(PIN_PC13, 4, 1)
+#define PIN_PC13__TF0			PINMUX_PIN(PIN_PC13, 5, 2)
+#define PIN_PC13__A2			PINMUX_PIN(PIN_PC13, 6, 2)
+#define PIN_PC14			78
+#define PIN_PC14__GPIO			PINMUX_PIN(PIN_PC14, 0, 0)
+#define PIN_PC14__LCDDAT6		PINMUX_PIN(PIN_PC14, 1, 2)
+#define PIN_PC14__GRX0			PINMUX_PIN(PIN_PC14, 2, 1)
+#define PIN_PC14__ISC_D5		PINMUX_PIN(PIN_PC14, 3, 1)
+#define PIN_PC14__TDO			PINMUX_PIN(PIN_PC14, 5, 2)
+#define PIN_PC14__A3			PINMUX_PIN(PIN_PC14, 6, 2)
+#define PIN_PC15			79
+#define PIN_PC15__GPIO			PINMUX_PIN(PIN_PC15, 0, 0)
+#define PIN_PC15__LCDDAT7		PINMUX_PIN(PIN_PC15, 1, 2)
+#define PIN_PC15__GRX1			PINMUX_PIN(PIN_PC15, 2, 1)
+#define PIN_PC15__ISC_D6		PINMUX_PIN(PIN_PC15, 3, 1)
+#define PIN_PC15__RD0			PINMUX_PIN(PIN_PC15, 5, 2)
+#define PIN_PC15__A4			PINMUX_PIN(PIN_PC15, 6, 2)
+#define PIN_PC16			80
+#define PIN_PC16__GPIO			PINMUX_PIN(PIN_PC16, 0, 0)
+#define PIN_PC16__LCDDAT10		PINMUX_PIN(PIN_PC16, 1, 2)
+#define PIN_PC16__GTX0			PINMUX_PIN(PIN_PC16, 2, 1)
+#define PIN_PC16__ISC_D7		PINMUX_PIN(PIN_PC16, 3, 1)
+#define PIN_PC16__RK0			PINMUX_PIN(PIN_PC16, 5, 2)
+#define PIN_PC16__A5			PINMUX_PIN(PIN_PC16, 6, 2)
+#define PIN_PC17			81
+#define PIN_PC17__GPIO			PINMUX_PIN(PIN_PC17, 0, 0)
+#define PIN_PC17__LCDDAT11		PINMUX_PIN(PIN_PC17, 1, 2)
+#define PIN_PC17__GTX1			PINMUX_PIN(PIN_PC17, 2, 1)
+#define PIN_PC17__ISC_D8		PINMUX_PIN(PIN_PC17, 3, 1)
+#define PIN_PC17__RF0			PINMUX_PIN(PIN_PC17, 5, 2)
+#define PIN_PC17__A6			PINMUX_PIN(PIN_PC17, 6, 2)
+#define PIN_PC18			82
+#define PIN_PC18__GPIO			PINMUX_PIN(PIN_PC18, 0, 0)
+#define PIN_PC18__LCDDAT12		PINMUX_PIN(PIN_PC18, 1, 2)
+#define PIN_PC18__GMDC			PINMUX_PIN(PIN_PC18, 2, 1)
+#define PIN_PC18__ISC_D9		PINMUX_PIN(PIN_PC18, 3, 1)
+#define PIN_PC18__FLEXCOM3_IO2		PINMUX_PIN(PIN_PC18, 5, 2)
+#define PIN_PC18__A7			PINMUX_PIN(PIN_PC18, 6, 2)
+#define PIN_PC19			83
+#define PIN_PC19__GPIO			PINMUX_PIN(PIN_PC19, 0, 0)
+#define PIN_PC19__LCDDAT13		PINMUX_PIN(PIN_PC19, 1, 2)
+#define PIN_PC19__GMDIO			PINMUX_PIN(PIN_PC19, 2, 1)
+#define PIN_PC19__ISC_D10		PINMUX_PIN(PIN_PC19, 3, 1)
+#define PIN_PC19__FLEXCOM3_IO1		PINMUX_PIN(PIN_PC19, 5, 2)
+#define PIN_PC19__A8			PINMUX_PIN(PIN_PC19, 6, 2)
+#define PIN_PC20			84
+#define PIN_PC20__GPIO			PINMUX_PIN(PIN_PC20, 0, 0)
+#define PIN_PC20__LCDDAT14		PINMUX_PIN(PIN_PC20, 1, 2)
+#define PIN_PC20__GRXCK			PINMUX_PIN(PIN_PC20, 2, 1)
+#define PIN_PC20__ISC_D11		PINMUX_PIN(PIN_PC20, 3, 1)
+#define PIN_PC20__FLEXCOM3_IO0		PINMUX_PIN(PIN_PC20, 5, 2)
+#define PIN_PC20__A9			PINMUX_PIN(PIN_PC20, 6, 2)
+#define PIN_PC21			85
+#define PIN_PC21__GPIO			PINMUX_PIN(PIN_PC21, 0, 0)
+#define PIN_PC21__LCDDAT15		PINMUX_PIN(PIN_PC21, 1, 2)
+#define PIN_PC21__GTXER			PINMUX_PIN(PIN_PC21, 2, 1)
+#define PIN_PC21__ISC_PCK		PINMUX_PIN(PIN_PC21, 3, 1)
+#define PIN_PC21__FLEXCOM3_IO3		PINMUX_PIN(PIN_PC21, 5, 2)
+#define PIN_PC21__A10			PINMUX_PIN(PIN_PC21, 6, 2)
+#define PIN_PC22			86
+#define PIN_PC22__GPIO			PINMUX_PIN(PIN_PC22, 0, 0)
+#define PIN_PC22__LCDDAT18		PINMUX_PIN(PIN_PC22, 1, 2)
+#define PIN_PC22__GCRS			PINMUX_PIN(PIN_PC22, 2, 1)
+#define PIN_PC22__ISC_VSYNC		PINMUX_PIN(PIN_PC22, 3, 1)
+#define PIN_PC22__FLEXCOM3_IO4		PINMUX_PIN(PIN_PC22, 5, 2)
+#define PIN_PC22__A11			PINMUX_PIN(PIN_PC22, 6, 2)
+#define PIN_PC23			87
+#define PIN_PC23__GPIO			PINMUX_PIN(PIN_PC23, 0, 0)
+#define PIN_PC23__LCDDAT19		PINMUX_PIN(PIN_PC23, 1, 2)
+#define PIN_PC23__GCOL			PINMUX_PIN(PIN_PC23, 2, 1)
+#define PIN_PC23__ISC_HSYNC		PINMUX_PIN(PIN_PC23, 3, 1)
+#define PIN_PC23__A12			PINMUX_PIN(PIN_PC23, 6, 2)
+#define PIN_PC24			88
+#define PIN_PC24__GPIO			PINMUX_PIN(PIN_PC24, 0, 0)
+#define PIN_PC24__LCDDAT20		PINMUX_PIN(PIN_PC24, 1, 2)
+#define PIN_PC24__GRX2			PINMUX_PIN(PIN_PC24, 2, 1)
+#define PIN_PC24__ISC_MCK		PINMUX_PIN(PIN_PC24, 3, 1)
+#define PIN_PC24__A13			PINMUX_PIN(PIN_PC24, 6, 2)
+#define PIN_PC25			89
+#define PIN_PC25__GPIO			PINMUX_PIN(PIN_PC25, 0, 0)
+#define PIN_PC25__LCDDAT21		PINMUX_PIN(PIN_PC25, 1, 2)
+#define PIN_PC25__GRX3			PINMUX_PIN(PIN_PC25, 2, 1)
+#define PIN_PC25__ISC_FIELD		PINMUX_PIN(PIN_PC25, 3, 1)
+#define PIN_PC25__A14			PINMUX_PIN(PIN_PC25, 6, 2)
+#define PIN_PC26			90
+#define PIN_PC26__GPIO			PINMUX_PIN(PIN_PC26, 0, 0)
+#define PIN_PC26__LCDDAT22		PINMUX_PIN(PIN_PC26, 1, 2)
+#define PIN_PC26__GTX2			PINMUX_PIN(PIN_PC26, 2, 1)
+#define PIN_PC26__CANTX1		PINMUX_PIN(PIN_PC26, 4, 1)
+#define PIN_PC26__A15			PINMUX_PIN(PIN_PC26, 6, 2)
+#define PIN_PC27			91
+#define PIN_PC27__GPIO			PINMUX_PIN(PIN_PC27, 0, 0)
+#define PIN_PC27__LCDDAT23		PINMUX_PIN(PIN_PC27, 1, 2)
+#define PIN_PC27__GTX3			PINMUX_PIN(PIN_PC27, 2, 1)
+#define PIN_PC27__PCK1			PINMUX_PIN(PIN_PC27, 3, 2)
+#define PIN_PC27__CANRX1		PINMUX_PIN(PIN_PC27, 4, 1)
+#define PIN_PC27__TWD0			PINMUX_PIN(PIN_PC27, 5, 2)
+#define PIN_PC27__A16			PINMUX_PIN(PIN_PC27, 6, 2)
+#define PIN_PC28			92
+#define PIN_PC28__GPIO			PINMUX_PIN(PIN_PC28, 0, 0)
+#define PIN_PC28__LCDPWM		PINMUX_PIN(PIN_PC28, 1, 2)
+#define PIN_PC28__FLEXCOM4_IO0		PINMUX_PIN(PIN_PC28, 2, 1)
+#define PIN_PC28__PCK2			PINMUX_PIN(PIN_PC28, 3, 2)
+#define PIN_PC28__TWCK0			PINMUX_PIN(PIN_PC28, 5, 2)
+#define PIN_PC28__A17			PINMUX_PIN(PIN_PC28, 6, 2)
+#define PIN_PC29			93
+#define PIN_PC29__GPIO			PINMUX_PIN(PIN_PC29, 0, 0)
+#define PIN_PC29__LCDDISP		PINMUX_PIN(PIN_PC29, 1, 2)
+#define PIN_PC29__FLEXCOM4_IO1		PINMUX_PIN(PIN_PC29, 2, 1)
+#define PIN_PC29__A18			PINMUX_PIN(PIN_PC29, 6, 2)
+#define PIN_PC30			94
+#define PIN_PC30__GPIO			PINMUX_PIN(PIN_PC30, 0, 0)
+#define PIN_PC30__LCDVSYNC		PINMUX_PIN(PIN_PC30, 1, 2)
+#define PIN_PC30__FLEXCOM4_IO2		PINMUX_PIN(PIN_PC30, 2, 1)
+#define PIN_PC30__A19			PINMUX_PIN(PIN_PC30, 6, 2)
+#define PIN_PC31			95
+#define PIN_PC31__GPIO			PINMUX_PIN(PIN_PC31, 0, 0)
+#define PIN_PC31__LCDHSYNC		PINMUX_PIN(PIN_PC31, 1, 2)
+#define PIN_PC31__FLEXCOM4_IO3		PINMUX_PIN(PIN_PC31, 2, 1)
+#define PIN_PC31__URXD3			PINMUX_PIN(PIN_PC31, 3, 2)
+#define PIN_PC31__A20			PINMUX_PIN(PIN_PC31, 6, 2)
+#define PIN_PD0				96
+#define PIN_PD0__GPIO			PINMUX_PIN(PIN_PD0, 0, 0)
+#define PIN_PD0__LCDPCK			PINMUX_PIN(PIN_PD0, 1, 2)
+#define PIN_PD0__FLEXCOM4_IO4		PINMUX_PIN(PIN_PD0, 2, 1)
+#define PIN_PD0__UTXD3			PINMUX_PIN(PIN_PD0, 3, 2)
+#define PIN_PD0__GTSUCOMP		PINMUX_PIN(PIN_PD0, 4, 2)
+#define PIN_PD0__A23			PINMUX_PIN(PIN_PD0, 6, 2)
+#define PIN_PD1				97
+#define PIN_PD1__GPIO			PINMUX_PIN(PIN_PD1, 0, 0)
+#define PIN_PD1__LCDDEN			PINMUX_PIN(PIN_PD1, 1, 2)
+#define PIN_PD1__GRXCK			PINMUX_PIN(PIN_PD1, 4, 2)
+#define PIN_PD1__A24			PINMUX_PIN(PIN_PD1, 6, 2)
+#define PIN_PD2				98
+#define PIN_PD2__GPIO			PINMUX_PIN(PIN_PD2, 0, 0)
+#define PIN_PD2__URXD1			PINMUX_PIN(PIN_PD2, 1, 1)
+#define PIN_PD2__GTXER			PINMUX_PIN(PIN_PD2, 4, 2)
+#define PIN_PD2__ISC_MCK		PINMUX_PIN(PIN_PD2, 5, 2)
+#define PIN_PD2__A25			PINMUX_PIN(PIN_PD2, 6, 2)
+#define PIN_PD3				99
+#define PIN_PD3__GPIO			PINMUX_PIN(PIN_PD3, 0, 0)
+#define PIN_PD3__UTXD1			PINMUX_PIN(PIN_PD3, 1, 1)
+#define PIN_PD3__FIQ			PINMUX_PIN(PIN_PD3, 2, 2)
+#define PIN_PD3__GCRS			PINMUX_PIN(PIN_PD3, 4, 2)
+#define PIN_PD3__ISC_D11		PINMUX_PIN(PIN_PD3, 5, 2)
+#define PIN_PD3__NWAIT			PINMUX_PIN(PIN_PD3, 6, 2)
+#define PIN_PD4				100
+#define PIN_PD4__GPIO			PINMUX_PIN(PIN_PD4, 0, 0)
+#define PIN_PD4__TWD1			PINMUX_PIN(PIN_PD4, 1, 2)
+#define PIN_PD4__URXD2			PINMUX_PIN(PIN_PD4, 2, 1)
+#define PIN_PD4__GCOL			PINMUX_PIN(PIN_PD4, 4, 2)
+#define PIN_PD4__ISC_D10		PINMUX_PIN(PIN_PD4, 5, 2)
+#define PIN_PD4__NCS0			PINMUX_PIN(PIN_PD4, 6, 2)
+#define PIN_PD5				101
+#define PIN_PD5__GPIO			PINMUX_PIN(PIN_PD5, 0, 0)
+#define PIN_PD5__TWCK1			PINMUX_PIN(PIN_PD5, 1, 2)
+#define PIN_PD5__UTXD2			PINMUX_PIN(PIN_PD5, 2, 1)
+#define PIN_PD5__GRX2			PINMUX_PIN(PIN_PD5, 4, 2)
+#define PIN_PD5__ISC_D9			PINMUX_PIN(PIN_PD5, 5, 2)
+#define PIN_PD5__NCS1			PINMUX_PIN(PIN_PD5, 6, 2)
+#define PIN_PD6				102
+#define PIN_PD6__GPIO			PINMUX_PIN(PIN_PD6, 0, 0)
+#define PIN_PD6__TCK			PINMUX_PIN(PIN_PD6, 1, 2)
+#define PIN_PD6__PCK1			PINMUX_PIN(PIN_PD6, 2, 1)
+#define PIN_PD6__GRX3			PINMUX_PIN(PIN_PD6, 4, 2)
+#define PIN_PD6__ISC_D8			PINMUX_PIN(PIN_PD6, 5, 2)
+#define PIN_PD6__NCS2			PINMUX_PIN(PIN_PD6, 6, 2)
+#define PIN_PD7				103
+#define PIN_PD7__GPIO			PINMUX_PIN(PIN_PD7, 0, 0)
+#define PIN_PD7__TDI			PINMUX_PIN(PIN_PD7, 1, 2)
+#define PIN_PD7__UTMI_RXVAL		PINMUX_PIN(PIN_PD7, 3, 1)
+#define PIN_PD7__GTX2			PINMUX_PIN(PIN_PD7, 4, 2)
+#define PIN_PD7__ISC_D0			PINMUX_PIN(PIN_PD7, 5, 2)
+#define PIN_PD7__NWR1_NBS1		PINMUX_PIN(PIN_PD7, 6, 2)
+#define PIN_PD8				104
+#define PIN_PD8__GPIO			PINMUX_PIN(PIN_PD8, 0, 0)
+#define PIN_PD8__TDO			PINMUX_PIN(PIN_PD8, 1, 2)
+#define PIN_PD8__UTMI_RXERR		PINMUX_PIN(PIN_PD8, 3, 1)
+#define PIN_PD8__GTX3			PINMUX_PIN(PIN_PD8, 4, 2)
+#define PIN_PD8__ISC_D1			PINMUX_PIN(PIN_PD8, 5, 2)
+#define PIN_PD8__NANDRDY		PINMUX_PIN(PIN_PD8, 6, 2)
+#define PIN_PD9				105
+#define PIN_PD9__GPIO			PINMUX_PIN(PIN_PD9, 0, 0)
+#define PIN_PD9__TMS			PINMUX_PIN(PIN_PD9, 1, 2)
+#define PIN_PD9__UTMI_RXACT		PINMUX_PIN(PIN_PD9, 3, 1)
+#define PIN_PD9__GTXCK			PINMUX_PIN(PIN_PD9, 4, 2)
+#define PIN_PD9__ISC_D2			PINMUX_PIN(PIN_PD9, 5, 2)
+#define PIN_PD10			106
+#define PIN_PD10__GPIO			PINMUX_PIN(PIN_PD10, 0, 0)
+#define PIN_PD10__NTRST			PINMUX_PIN(PIN_PD10, 1, 2)
+#define PIN_PD10__UTMI_HDIS		PINMUX_PIN(PIN_PD10, 3, 1)
+#define PIN_PD10__GTXEN			PINMUX_PIN(PIN_PD10, 4, 2)
+#define PIN_PD10__ISC_D3		PINMUX_PIN(PIN_PD10, 5, 2)
+#define PIN_PD11			107
+#define PIN_PD11__GPIO			PINMUX_PIN(PIN_PD11, 0, 0)
+#define PIN_PD11__TIOA1			PINMUX_PIN(PIN_PD11, 1, 3)
+#define PIN_PD11__PCK2			PINMUX_PIN(PIN_PD11, 2, 2)
+#define PIN_PD11__UTMI_LS0		PINMUX_PIN(PIN_PD11, 3, 1)
+#define PIN_PD11__GRXDV			PINMUX_PIN(PIN_PD11, 4, 2)
+#define PIN_PD11__ISC_D4		PINMUX_PIN(PIN_PD11, 5, 2)
+#define PIN_PD11__ISC_MCK		PINMUX_PIN(PIN_PD11, 7, 4)
+#define PIN_PD12			108
+#define PIN_PD12__GPIO			PINMUX_PIN(PIN_PD12, 0, 0)
+#define PIN_PD12__TIOB1			PINMUX_PIN(PIN_PD12, 1, 3)
+#define PIN_PD12__FLEXCOM4_IO0		PINMUX_PIN(PIN_PD12, 2, 2)
+#define PIN_PD12__UTMI_LS1		PINMUX_PIN(PIN_PD12, 3, 1)
+#define PIN_PD12__GRXER			PINMUX_PIN(PIN_PD12, 4, 2)
+#define PIN_PD12__ISC_D5		PINMUX_PIN(PIN_PD12, 5, 2)
+#define PIN_PD12__ISC_D4		PINMUX_PIN(PIN_PD12, 6, 4)
+#define PIN_PD13			109
+#define PIN_PD13__GPIO			PINMUX_PIN(PIN_PD13, 0, 0)
+#define PIN_PD13__TCLK1			PINMUX_PIN(PIN_PD13, 1, 3)
+#define PIN_PD13__FLEXCOM4_IO1		PINMUX_PIN(PIN_PD13, 2, 2)
+#define PIN_PD13__UTMI_CDRPCSEL0	PINMUX_PIN(PIN_PD13, 3, 1)
+#define PIN_PD13__GRX0			PINMUX_PIN(PIN_PD13, 4, 2)
+#define PIN_PD13__ISC_D6		PINMUX_PIN(PIN_PD13, 5, 2)
+#define PIN_PD13__ISC_D5		PINMUX_PIN(PIN_PD13, 6, 4)
+#define PIN_PD14			110
+#define PIN_PD14__GPIO			PINMUX_PIN(PIN_PD14, 0, 0)
+#define PIN_PD14__TCK			PINMUX_PIN(PIN_PD14, 1, 1)
+#define PIN_PD14__FLEXCOM4_IO2		PINMUX_PIN(PIN_PD14, 2, 2)
+#define PIN_PD14__UTMI_CDRPCSEL1	PINMUX_PIN(PIN_PD14, 3, 1)
+#define PIN_PD14__GRX1			PINMUX_PIN(PIN_PD14, 4, 2)
+#define PIN_PD14__ISC_D7		PINMUX_PIN(PIN_PD14, 5, 2)
+#define PIN_PD14__ISC_D6		PINMUX_PIN(PIN_PD14, 6, 4)
+#define PIN_PD15			111
+#define PIN_PD15__GPIO			PINMUX_PIN(PIN_PD15, 0, 0)
+#define PIN_PD15__TDI			PINMUX_PIN(PIN_PD15, 1, 1)
+#define PIN_PD15__FLEXCOM4_IO3		PINMUX_PIN(PIN_PD15, 2, 2)
+#define PIN_PD15__UTMI_CDRCPDIVEN	PINMUX_PIN(PIN_PD15, 3, 1)
+#define PIN_PD15__GTX0			PINMUX_PIN(PIN_PD15, 4, 2)
+#define PIN_PD15__ISC_PCK		PINMUX_PIN(PIN_PD15, 5, 2)
+#define PIN_PD15__ISC_D7		PINMUX_PIN(PIN_PD15, 6, 4)
+#define PIN_PD16			112
+#define PIN_PD16__GPIO			PINMUX_PIN(PIN_PD16, 0, 0)
+#define PIN_PD16__TDO			PINMUX_PIN(PIN_PD16, 1, 1)
+#define PIN_PD16__FLEXCOM4_IO4		PINMUX_PIN(PIN_PD16, 2, 2)
+#define PIN_PD16__UTMI_CDRBISTEN	PINMUX_PIN(PIN_PD16, 3, 1)
+#define PIN_PD16__GTX1			PINMUX_PIN(PIN_PD16, 4, 2)
+#define PIN_PD16__ISC_VSYNC		PINMUX_PIN(PIN_PD16, 5, 2)
+#define PIN_PD16__ISC_D8		PINMUX_PIN(PIN_PD16, 6, 4)
+#define PIN_PD17			113
+#define PIN_PD17__GPIO			PINMUX_PIN(PIN_PD17, 0, 0)
+#define PIN_PD17__TMS			PINMUX_PIN(PIN_PD17, 1, 1)
+#define PIN_PD17__UTMI_CDRCPSELDIV	PINMUX_PIN(PIN_PD17, 3, 1)
+#define PIN_PD17__GMDC			PINMUX_PIN(PIN_PD17, 4, 2)
+#define PIN_PD17__ISC_HSYNC		PINMUX_PIN(PIN_PD17, 5, 2)
+#define PIN_PD17__ISC_D9		PINMUX_PIN(PIN_PD17, 6, 4)
+#define PIN_PD18			114
+#define PIN_PD18__GPIO			PINMUX_PIN(PIN_PD18, 0, 0)
+#define PIN_PD18__NTRST			PINMUX_PIN(PIN_PD18, 1, 1)
+#define PIN_PD18__GMDIO			PINMUX_PIN(PIN_PD18, 4, 2)
+#define PIN_PD18__ISC_FIELD		PINMUX_PIN(PIN_PD18, 5, 2)
+#define PIN_PD18__ISC_D10		PINMUX_PIN(PIN_PD18, 6, 4)
+#define PIN_PD19			115
+#define PIN_PD19__GPIO			PINMUX_PIN(PIN_PD19, 0, 0)
+#define PIN_PD19__PCK0			PINMUX_PIN(PIN_PD19, 1, 1)
+#define PIN_PD19__TWD1			PINMUX_PIN(PIN_PD19, 2, 3)
+#define PIN_PD19__URXD2			PINMUX_PIN(PIN_PD19, 3, 3)
+#define PIN_PD19__I2SC0_CK		PINMUX_PIN(PIN_PD19, 5, 2)
+#define PIN_PD19__ISC_D11		PINMUX_PIN(PIN_PD19, 6, 4)
+#define PIN_PD20			116
+#define PIN_PD20__GPIO			PINMUX_PIN(PIN_PD20, 0, 0)
+#define PIN_PD20__TIOA2			PINMUX_PIN(PIN_PD20, 1, 3)
+#define PIN_PD20__TWCK1			PINMUX_PIN(PIN_PD20, 2, 3)
+#define PIN_PD20__UTXD2			PINMUX_PIN(PIN_PD20, 3, 3)
+#define PIN_PD20__I2SC0_MCK		PINMUX_PIN(PIN_PD20, 5, 2)
+#define PIN_PD20__ISC_PCK		PINMUX_PIN(PIN_PD20, 6, 4)
+#define PIN_PD21			117
+#define PIN_PD21__GPIO			PINMUX_PIN(PIN_PD21, 0, 0)
+#define PIN_PD21__TIOB2			PINMUX_PIN(PIN_PD21, 1, 3)
+#define PIN_PD21__TWD0			PINMUX_PIN(PIN_PD21, 2, 4)
+#define PIN_PD21__FLEXCOM4_IO0		PINMUX_PIN(PIN_PD21, 3, 3)
+#define PIN_PD21__I2SC0_WS		PINMUX_PIN(PIN_PD21, 5, 2)
+#define PIN_PD21__ISC_VSYNC		PINMUX_PIN(PIN_PD21, 6, 4)
+#define PIN_PD22			118
+#define PIN_PD22__GPIO			PINMUX_PIN(PIN_PD22, 0, 0)
+#define PIN_PD22__TCLK2			PINMUX_PIN(PIN_PD22, 1, 3)
+#define PIN_PD22__TWCK0			PINMUX_PIN(PIN_PD22, 2, 4)
+#define PIN_PD22__FLEXCOM4_IO1		PINMUX_PIN(PIN_PD22, 3, 3)
+#define PIN_PD22__I2SC0_DI0		PINMUX_PIN(PIN_PD22, 5, 2)
+#define PIN_PD22__ISC_HSYNC		PINMUX_PIN(PIN_PD22, 6, 4)
+#define PIN_PD23			119
+#define PIN_PD23__GPIO			PINMUX_PIN(PIN_PD23, 0, 0)
+#define PIN_PD23__URXD2			PINMUX_PIN(PIN_PD23, 1, 2)
+#define PIN_PD23__FLEXCOM4_IO2		PINMUX_PIN(PIN_PD23, 3, 3)
+#define PIN_PD23__I2SC0_DO0		PINMUX_PIN(PIN_PD23, 5, 2)
+#define PIN_PD23__ISC_FIELD		PINMUX_PIN(PIN_PD23, 6, 4)
+#define PIN_PD24			120
+#define PIN_PD24__GPIO			PINMUX_PIN(PIN_PD24, 0, 0)
+#define PIN_PD24__UTXD2			PINMUX_PIN(PIN_PD23, 1, 2)
+#define PIN_PD24__FLEXCOM4_IO3		PINMUX_PIN(PIN_PD23, 3, 3)
+#define PIN_PD25			121
+#define PIN_PD25__GPIO			PINMUX_PIN(PIN_PD25, 0, 0)
+#define PIN_PD25__SPI1_SPCK		PINMUX_PIN(PIN_PD25, 1, 3)
+#define PIN_PD25__FLEXCOM4_IO4		PINMUX_PIN(PIN_PD25, 3, 3)
+#define PIN_PD26			122
+#define PIN_PD26__GPIO			PINMUX_PIN(PIN_PD26, 0, 0)
+#define PIN_PD26__SPI1_MOSI		PINMUX_PIN(PIN_PD26, 1, 3)
+#define PIN_PD26__FLEXCOM2_IO0		PINMUX_PIN(PIN_PD26, 3, 2)
+#define PIN_PD27			123
+#define PIN_PD27__GPIO			PINMUX_PIN(PIN_PD27, 0, 0)
+#define PIN_PD27__SPI1_MISO		PINMUX_PIN(PIN_PD27, 1, 3)
+#define PIN_PD27__TCK			PINMUX_PIN(PIN_PD27, 2, 3)
+#define PIN_PD27__FLEXCOM2_IO1		PINMUX_PIN(PIN_PD27, 3, 2)
+#define PIN_PD28			124
+#define PIN_PD28__GPIO			PINMUX_PIN(PIN_PD28, 0, 0)
+#define PIN_PD28__SPI1_NPCS0		PINMUX_PIN(PIN_PD28, 1, 3)
+#define PIN_PD28__TCI			PINMUX_PIN(PIN_PD28, 2, 3)
+#define PIN_PD28__FLEXCOM2_IO2		PINMUX_PIN(PIN_PD28, 3, 2)
+#define PIN_PD29			125
+#define PIN_PD29__GPIO			PINMUX_PIN(PIN_PD29, 0, 0)
+#define PIN_PD29__SPI1_NPCS1		PINMUX_PIN(PIN_PD29, 1, 3)
+#define PIN_PD29__TDO			PINMUX_PIN(PIN_PD29, 2, 3)
+#define PIN_PD29__FLEXCOM2_IO3		PINMUX_PIN(PIN_PD29, 3, 2)
+#define PIN_PD29__TIOA3			PINMUX_PIN(PIN_PD29, 4, 3)
+#define PIN_PD29__TWD0			PINMUX_PIN(PIN_PD29, 5, 3)
+#define PIN_PD30			126
+#define PIN_PD30__GPIO			PINMUX_PIN(PIN_PD30, 0, 0)
+#define PIN_PD30__SPI1_NPCS2		PINMUX_PIN(PIN_PD30, 1, 3)
+#define PIN_PD30__TMS			PINMUX_PIN(PIN_PD30, 2, 3)
+#define PIN_PD30__FLEXCOM2_IO4		PINMUX_PIN(PIN_PD30, 3, 2)
+#define PIN_PD30__TIOB3			PINMUX_PIN(PIN_PD30, 4, 3)
+#define PIN_PD30__TWCK0			PINMUX_PIN(PIN_PD30, 5, 3)
+#define PIN_PD31			127
+#define PIN_PD31__GPIO			PINMUX_PIN(PIN_PD31, 0, 0)
+#define PIN_PD31__ADTRG			PINMUX_PIN(PIN_PD31, 1, 1)
+#define PIN_PD31__NTRST			PINMUX_PIN(PIN_PD31, 2, 3)
+#define PIN_PD31__IRQ			PINMUX_PIN(PIN_PD31, 3, 4)
+#define PIN_PD31__TCLK3			PINMUX_PIN(PIN_PD31, 4, 3)
+#define PIN_PD31__PCK0			PINMUX_PIN(PIN_PD31, 5, 2)

arch/arm/dts/sama5d2.dtsi

@@ -0,0 +1,671 @@
+#include "skeleton.dtsi"
+
+/ {
+	model = "Atmel SAMA5D2 family SoC";
+	compatible = "atmel,sama5d2";
+
+	aliases {
+		spi0 = &spi0;
+		spi1 = &qspi0;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+	};
+
+	clocks {
+		slow_xtal: slow_xtal {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <0>;
+		};
+
+		main_xtal: main_xtal {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <0>;
+		};
+	};
+
+	ahb {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		usb1: ohci@00400000 {
+			compatible = "atmel,at91rm9200-ohci", "usb-ohci";
+			reg = <0x00400000 0x100000>;
+			clocks = <&uhphs_clk>, <&uhphs_clk>, <&uhpck>;
+			clock-names = "ohci_clk", "hclk", "uhpck";
+			status = "disabled";
+		};
+
+		usb2: ehci@00500000 {
+			compatible = "atmel,at91sam9g45-ehci", "usb-ehci";
+			reg = <0x00500000 0x100000>;
+			clocks = <&utmi>, <&uhphs_clk>;
+			clock-names = "usb_clk", "ehci_clk";
+			status = "disabled";
+		};
+
+		sdmmc0: sdio-host@a0000000 {
+			compatible = "atmel,sama5d2-sdhci";
+			reg = <0xa0000000 0x300>;
+			clocks = <&sdmmc0_hclk>, <&sdmmc0_gclk>, <&main>;
+			clock-names = "hclock", "multclk", "baseclk";
+			status = "disabled";
+		};
+
+		sdmmc1: sdio-host@b0000000 {
+			compatible = "atmel,sama5d2-sdhci";
+			reg = <0xb0000000 0x300>;
+			clocks = <&sdmmc1_hclk>, <&sdmmc1_gclk>, <&main>;
+			clock-names = "hclock", "multclk", "baseclk";
+			status = "disabled";
+		};
+
+		apb {
+			compatible = "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			pmc: pmc@f0014000 {
+				compatible = "atmel,sama5d2-pmc", "syscon";
+				reg = <0xf0014000 0x160>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				#interrupt-cells = <1>;
+
+				main: mainck {
+					compatible = "atmel,at91sam9x5-clk-main";
+					#clock-cells = <0>;
+				};
+
+				plla: pllack {
+					compatible = "atmel,sama5d3-clk-pll";
+					#clock-cells = <0>;
+					clocks = <&main>;
+					reg = <0>;
+					atmel,clk-input-range = <12000000 12000000>;
+					#atmel,pll-clk-output-range-cells = <4>;
+					atmel,pll-clk-output-ranges = <600000000 1200000000 0 0>;
+				};
+
+				plladiv: plladivck {
+					compatible = "atmel,at91sam9x5-clk-plldiv";
+					#clock-cells = <0>;
+					clocks = <&plla>;
+				};
+
+				audio_pll_frac: audiopll_fracck {
+					compatible = "atmel,sama5d2-clk-audio-pll-frac";
+					#clock-cells = <0>;
+					clocks = <&main>;
+				};
+
+				audio_pll_pad: audiopll_padck {
+					compatible = "atmel,sama5d2-clk-audio-pll-pad";
+					#clock-cells = <0>;
+					clocks = <&audio_pll_frac>;
+				};
+
+				audio_pll_pmc: audiopll_pmcck {
+					compatible = "atmel,sama5d2-clk-audio-pll-pmc";
+					#clock-cells = <0>;
+					clocks = <&audio_pll_frac>;
+				};
+
+				utmi: utmick {
+					compatible = "atmel,at91sam9x5-clk-utmi";
+					#clock-cells = <0>;
+					clocks = <&main>;
+				};
+
+				mck: masterck {
+					compatible = "atmel,at91sam9x5-clk-master";
+					#clock-cells = <0>;
+					clocks = <&main>, <&plladiv>, <&utmi>;
+					atmel,clk-output-range = <124000000 166000000>;
+					atmel,clk-divisors = <1 2 4 3>;
+				};
+
+				h32ck: h32mxck {
+					#clock-cells = <0>;
+					compatible = "atmel,sama5d4-clk-h32mx";
+					clocks = <&mck>;
+				};
+
+				usb: usbck {
+					compatible = "atmel,at91sam9x5-clk-usb";
+					#clock-cells = <0>;
+					clocks = <&plladiv>, <&utmi>;
+				};
+
+				prog: progck {
+					compatible = "atmel,at91sam9x5-clk-programmable";
+					#address-cells = <1>;
+					#size-cells = <0>;
+					interrupt-parent = <&pmc>;
+					clocks = <&main>, <&plladiv>, <&utmi>, <&mck>;
+
+					prog0: prog0 {
+						#clock-cells = <0>;
+						reg = <0>;
+					};
+
+					prog1: prog1 {
+						#clock-cells = <0>;
+						reg = <1>;
+					};
+
+					prog2: prog2 {
+						#clock-cells = <0>;
+						reg = <2>;
+					};
+				};
+
+				systemck {
+					compatible = "atmel,at91rm9200-clk-system";
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					ddrck: ddrck {
+						#clock-cells = <0>;
+						reg = <2>;
+						clocks = <&mck>;
+					};
+
+					lcdck: lcdck {
+						#clock-cells = <0>;
+						reg = <3>;
+						clocks = <&mck>;
+					};
+
+					uhpck: uhpck {
+						#clock-cells = <0>;
+						reg = <6>;
+						clocks = <&usb>;
+					};
+
+					udpck: udpck {
+						#clock-cells = <0>;
+						reg = <7>;
+						clocks = <&usb>;
+					};
+
+					pck0: pck0 {
+						#clock-cells = <0>;
+						reg = <8>;
+						clocks = <&prog0>;
+					};
+
+					pck1: pck1 {
+						#clock-cells = <0>;
+						reg = <9>;
+						clocks = <&prog1>;
+					};
+
+					pck2: pck2 {
+						#clock-cells = <0>;
+						reg = <10>;
+						clocks = <&prog2>;
+					};
+
+					iscck: iscck {
+						#clock-cells = <0>;
+						reg = <18>;
+						clocks = <&mck>;
+					};
+				};
+
+				periph32ck {
+					compatible = "atmel,at91sam9x5-clk-peripheral";
+					#address-cells = <1>;
+					#size-cells = <0>;
+					clocks = <&h32ck>;
+
+					macb0_clk: macb0_clk {
+						#clock-cells = <0>;
+						reg = <5>;
+						atmel,clk-output-range = <0 83000000>;
+					};
+
+					tdes_clk: tdes_clk {
+						#clock-cells = <0>;
+						reg = <11>;
+						atmel,clk-output-range = <0 83000000>;
+					};
+
+					matrix1_clk: matrix1_clk {
+						#clock-cells = <0>;
+						reg = <14>;
+					};
+
+					hsmc_clk: hsmc_clk {
+						#clock-cells = <0>;
+						reg = <17>;
+					};
+
+					pioA_clk: pioA_clk {
+						#clock-cells = <0>;
+						reg = <18>;
+						atmel,clk-output-range = <0 83000000>;
+					};
+
+					flx0_clk: flx0_clk {
+						#clock-cells = <0>;
+						reg = <19>;
+						atmel,clk-output-range = <0 83000000>;
+					};
+
+					flx1_clk: flx1_clk {
+						#clock-cells = <0>;
+						reg = <20>;
+						atmel,clk-output-range = <0 83000000>;
+					};
+
+					flx2_clk: flx2_clk {
+						#clock-cells = <0>;
+						reg = <21>;
+						atmel,clk-output-range = <0 83000000>;
+					};
+
+					flx3_clk: flx3_clk {
+						#clock-cells = <0>;
+						reg = <22>;
+						atmel,clk-output-range = <0 83000000>;
+					};
+
+					flx4_clk: flx4_clk {
+						#clock-cells = <0>;
+						reg = <23>;
+						atmel,clk-output-range = <0 83000000>;
+					};
+
+					uart0_clk: uart0_clk {
+						#clock-cells = <0>;
+						reg = <24>;
+						atmel,clk-output-range = <0 83000000>;
+					};
+
+					uart1_clk: uart1_clk {
+						#clock-cells = <0>;
+						reg = <25>;
+						atmel,clk-output-range = <0 83000000>;
+					};
+
+					uart2_clk: uart2_clk {
+						#clock-cells = <0>;
+						reg = <26>;
+						atmel,clk-output-range = <0 83000000>;
+					};
+
+					uart3_clk: uart3_clk {
+						#clock-cells = <0>;
+						reg = <27>;
+						atmel,clk-output-range = <0 83000000>;
+					};
+
+					uart4_clk: uart4_clk {
+						#clock-cells = <0>;
+						reg = <28>;
+						atmel,clk-output-range = <0 83000000>;
+					};
+
+					twi0_clk: twi0_clk {
+						reg = <29>;
+						#clock-cells = <0>;
+						atmel,clk-output-range = <0 83000000>;
+					};
+
+					twi1_clk: twi1_clk {
+						#clock-cells = <0>;
+						reg = <30>;
+						atmel,clk-output-range = <0 83000000>;
+					};
+
+					spi0_clk: spi0_clk {
+						#clock-cells = <0>;
+						reg = <33>;
+						atmel,clk-output-range = <0 83000000>;
+					};
+
+					spi1_clk: spi1_clk {
+						#clock-cells = <0>;
+						reg = <34>;
+						atmel,clk-output-range = <0 83000000>;
+					};
+
+					tcb0_clk: tcb0_clk {
+						#clock-cells = <0>;
+						reg = <35>;
+						atmel,clk-output-range = <0 83000000>;
+					};
+
+					tcb1_clk: tcb1_clk {
+						#clock-cells = <0>;
+						reg = <36>;
+						atmel,clk-output-range = <0 83000000>;
+					};
+
+					pwm_clk: pwm_clk {
+						#clock-cells = <0>;
+						reg = <38>;
+						atmel,clk-output-range = <0 83000000>;
+					};
+
+					adc_clk: adc_clk {
+						#clock-cells = <0>;
+						reg = <40>;
+						atmel,clk-output-range = <0 83000000>;
+					};
+
+					uhphs_clk: uhphs_clk {
+						#clock-cells = <0>;
+						reg = <41>;
+						atmel,clk-output-range = <0 83000000>;
+					};
+
+					udphs_clk: udphs_clk {
+						#clock-cells = <0>;
+						reg = <42>;
+						atmel,clk-output-range = <0 83000000>;
+					};
+
+					ssc0_clk: ssc0_clk {
+						#clock-cells = <0>;
+						reg = <43>;
+						atmel,clk-output-range = <0 83000000>;
+					};
+
+					ssc1_clk: ssc1_clk {
+						#clock-cells = <0>;
+						reg = <44>;
+						atmel,clk-output-range = <0 83000000>;
+					};
+
+					trng_clk: trng_clk {
+						#clock-cells = <0>;
+						reg = <47>;
+						atmel,clk-output-range = <0 83000000>;
+					};
+
+					pdmic_clk: pdmic_clk {
+						#clock-cells = <0>;
+						reg = <48>;
+						atmel,clk-output-range = <0 83000000>;
+					};
+
+					i2s0_clk: i2s0_clk {
+						#clock-cells = <0>;
+						reg = <54>;
+						atmel,clk-output-range = <0 83000000>;
+					};
+
+					i2s1_clk: i2s1_clk {
+						#clock-cells = <0>;
+						reg = <55>;
+						atmel,clk-output-range = <0 83000000>;
+					};
+
+					can0_clk: can0_clk {
+						#clock-cells = <0>;
+						reg = <56>;
+						atmel,clk-output-range = <0 83000000>;
+					};
+
+					can1_clk: can1_clk {
+						#clock-cells = <0>;
+						reg = <57>;
+						atmel,clk-output-range = <0 83000000>;
+					};
+
+					classd_clk: classd_clk {
+						#clock-cells = <0>;
+						reg = <59>;
+						atmel,clk-output-range = <0 83000000>;
+					};
+				};
+
+				periph64ck {
+					compatible = "atmel,at91sam9x5-clk-peripheral";
+					#address-cells = <1>;
+					#size-cells = <0>;
+					clocks = <&mck>;
+
+					dma0_clk: dma0_clk {
+						#clock-cells = <0>;
+						reg = <6>;
+					};
+
+					dma1_clk: dma1_clk {
+						#clock-cells = <0>;
+						reg = <7>;
+					};
+
+					aes_clk: aes_clk {
+						#clock-cells = <0>;
+						reg = <9>;
+					};
+
+					aesb_clk: aesb_clk {
+						#clock-cells = <0>;
+						reg = <10>;
+					};
+
+					sha_clk: sha_clk {
+						#clock-cells = <0>;
+						reg = <12>;
+					};
+
+					mpddr_clk: mpddr_clk {
+						#clock-cells = <0>;
+						reg = <13>;
+					};
+
+					matrix0_clk: matrix0_clk {
+						#clock-cells = <0>;
+						reg = <15>;
+					};
+
+					sdmmc0_hclk: sdmmc0_hclk {
+						#clock-cells = <0>;
+						reg = <31>;
+					};
+
+					sdmmc1_hclk: sdmmc1_hclk {
+						#clock-cells = <0>;
+						reg = <32>;
+					};
+
+					lcdc_clk: lcdc_clk {
+						#clock-cells = <0>;
+						reg = <45>;
+					};
+
+					isc_clk: isc_clk {
+						#clock-cells = <0>;
+						reg = <46>;
+					};
+
+					qspi0_clk: qspi0_clk {
+						#clock-cells = <0>;
+						reg = <52>;
+					};
+
+					qspi1_clk: qspi1_clk {
+						#clock-cells = <0>;
+						reg = <53>;
+					};
+				};
+
+				gck {
+					compatible = "atmel,sama5d2-clk-generated";
+					#address-cells = <1>;
+					#size-cells = <0>;
+					interrupt-parent = <&pmc>;
+					clocks = <&main>, <&plla>, <&utmi>, <&mck>;
+
+					sdmmc0_gclk: sdmmc0_gclk {
+						#clock-cells = <0>;
+						reg = <31>;
+					};
+
+					sdmmc1_gclk: sdmmc1_gclk {
+						#clock-cells = <0>;
+						reg = <32>;
+					};
+
+					tcb0_gclk: tcb0_gclk {
+						#clock-cells = <0>;
+						reg = <35>;
+						atmel,clk-output-range = <0 83000000>;
+					};
+
+					tcb1_gclk: tcb1_gclk {
+						#clock-cells = <0>;
+						reg = <36>;
+						atmel,clk-output-range = <0 83000000>;
+					};
+
+					pwm_gclk: pwm_gclk {
+						#clock-cells = <0>;
+						reg = <38>;
+						atmel,clk-output-range = <0 83000000>;
+					};
+
+					pdmic_gclk: pdmic_gclk {
+						#clock-cells = <0>;
+						reg = <48>;
+					};
+
+					i2s0_gclk: i2s0_gclk {
+						#clock-cells = <0>;
+						reg = <54>;
+					};
+
+					i2s1_gclk: i2s1_gclk {
+						#clock-cells = <0>;
+						reg = <55>;
+					};
+
+					can0_gclk: can0_gclk {
+						#clock-cells = <0>;
+						reg = <56>;
+						atmel,clk-output-range = <0 80000000>;
+					};
+
+					can1_gclk: can1_gclk {
+						#clock-cells = <0>;
+						reg = <57>;
+						atmel,clk-output-range = <0 80000000>;
+					};
+
+					classd_gclk: classd_gclk {
+						#clock-cells = <0>;
+						reg = <59>;
+						atmel,clk-output-range = <0 100000000>;
+					};
+				};
+			};
+
+			qspi0: spi@f0020000 {
+				compatible = "atmel,sama5d2-qspi";
+				reg = <0xf0020000 0x100>, <0xd0000000 0x08000000>;
+				reg-names = "qspi_base", "qspi_mmap";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&qspi0_clk>;
+				status = "disabled";
+			};
+
+			spi0: spi@f8000000 {
+				compatible = "atmel,at91rm9200-spi";
+				reg = <0xf8000000 0x100>;
+				clocks = <&spi0_clk>;
+				clock-names = "spi_clk";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			macb0: ethernet@f8008000 {
+				compatible = "cdns,macb";
+				reg = <0xf8008000 0x1000>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&macb0_clk>, <&macb0_clk>;
+				clock-names = "hclk", "pclk";
+				status = "disabled";
+			};
+
+			uart1: serial@f8020000 {
+				compatible = "atmel,at91sam9260-usart";
+				reg = <0xf8020000 0x100>;
+				status = "disabled";
+			};
+
+			i2c0: i2c@f8028000 {
+				compatible = "atmel,sama5d2-i2c";
+				reg = <0xf8028000 0x100>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&twi0_clk>;
+				status = "disabled";
+			};
+
+			sckc@f8048050 {
+				compatible = "atmel,at91sam9x5-sckc";
+				reg = <0xf8048050 0x4>;
+
+				slow_rc_osc: slow_rc_osc {
+					compatible = "atmel,at91sam9x5-clk-slow-rc-osc";
+					#clock-cells = <0>;
+					clock-frequency = <32768>;
+					clock-accuracy = <250000000>;
+					atmel,startup-time-usec = <75>;
+				};
+
+				slow_osc: slow_osc {
+					compatible = "atmel,at91sam9x5-clk-slow-osc";
+					#clock-cells = <0>;
+					clocks = <&slow_xtal>;
+					atmel,startup-time-usec = <1200000>;
+				};
+
+				clk32k: slowck {
+					compatible = "atmel,at91sam9x5-clk-slow";
+					#clock-cells = <0>;
+					clocks = <&slow_rc_osc &slow_osc>;
+				};
+			};
+
+			spi1: spi@fc000000 {
+				compatible = "atmel,at91rm9200-spi";
+				reg = <0xfc000000 0x100>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c1: i2c@fc028000 {
+				compatible = "atmel,sama5d2-i2c";
+				reg = <0xfc028000 0x100>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&twi1_clk>;
+				status = "disabled";
+			};
+
+			pioA: gpio@fc038000 {
+				compatible = "atmel,sama5d2-gpio";
+				reg = <0xfc038000 0x600>;
+				clocks = <&pioA_clk>;
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				pinctrl {
+					compatible = "atmel,sama5d2-pinctrl";
+				};
+			};
+		};
+	};
+};

arch/arm/dts/sun8i-h3-orangepi-one.dts

@@ -94,6 +94,17 @@
 	status = "okay";
 };
 
+&emac {
+	phy = <&phy1>;
+	phy-mode = "mii";
+	allwinner,use-internal-phy;
+	allwinner,leds-active-low;
+	status = "okay";
+	phy1: ethernet-phy@1 {
+		reg = <1>;
+	};
+};
+
 &mmc0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;

arch/arm/dts/sun8i-h3-orangepi-pc-plus.dts

@@ -0,0 +1,87 @@
+/*
+ * Copyright (C) 2016 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/* The Orange Pi PC Plus is an extended version of the regular PC */
+#include "sun8i-h3-orangepi-pc.dts"
+
+/ {
+	model = "Xunlong Orange Pi PC / PC Plus";
+
+	aliases {
+		/* ethernet0 is the H3 emac, defined in sun8i-h3.dtsi */
+		ethernet1 = &rtl8189ftv;
+	};
+};
+
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins_a>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	/*
+	 * Explicitly define the sdio device, so that we can add an ethernet
+	 * alias for it (which e.g. makes u-boot set a mac-address).
+	 */
+	rtl8189ftv: sdio_wifi@1 {
+		reg = <1>;
+	};
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_8bit_pins>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <8>;
+	non-removable;
+	cap-mmc-hw-reset;
+	status = "okay";
+};
+
+&mmc2_8bit_pins {
+	/* Increase drive strength for DDR modes */
+	allwinner,drive = <SUN4I_PINCTRL_40_MA>;
+	/* eMMC is missing pull-ups */
+	allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+};

arch/arm/dts/sun8i-h3.dtsi

@@ -48,6 +48,10 @@
 / {
 	interrupt-parent = <&gic>;
 
+	aliases {
+		ethernet0 = <&emac>;
+	};
+
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;

arch/arm/dts/tegra186-p2771-0000-a02.dts

@@ -5,4 +5,28 @@
 / {
 	model = "NVIDIA P2771-0000 A02";
 	compatible = "nvidia,p2771-0000-a02", "nvidia,p2771-0000", "nvidia,tegra186";
+
+	sdhci@3400000 {
+		cd-gpios = <&gpio_main TEGRA_MAIN_GPIO(P, 6) GPIO_ACTIVE_LOW>;
+		power-gpios = <&gpio_main TEGRA_MAIN_GPIO(P, 5) GPIO_ACTIVE_HIGH>;
+	};
+
+	pcie-controller@10003000 {
+		status = "okay";
+
+		pci@1,0 {
+			status = "okay";
+			nvidia,num-lanes = <2>;
+		};
+
+		pci@2,0 {
+			status = "disabled";
+			nvidia,num-lanes = <1>;
+		};
+
+		pci@3,0 {
+			status = "okay";
+			nvidia,num-lanes = <1>;
+		};
+	};
 };

arch/arm/dts/tegra186-p2771-0000-b00.dts

@@ -5,4 +5,28 @@
 / {
 	model = "NVIDIA P2771-0000 B00";
 	compatible = "nvidia,p2771-0000-b00", "nvidia,p2771-0000", "nvidia,tegra186";
+
+	sdhci@3400000 {
+		cd-gpios = <&gpio_main TEGRA_MAIN_GPIO(P, 5) GPIO_ACTIVE_LOW>;
+		power-gpios = <&gpio_main TEGRA_MAIN_GPIO(P, 6) GPIO_ACTIVE_HIGH>;
+	};
+
+	pcie-controller@10003000 {
+		status = "okay";
+
+		pci@1,0 {
+			status = "okay";
+			nvidia,num-lanes = <4>;
+		};
+
+		pci@2,0 {
+			status = "disabled";
+			nvidia,num-lanes = <0>;
+		};
+
+		pci@3,0 {
+			status = "disabled";
+			nvidia,num-lanes = <1>;
+		};
+	};
 };

arch/arm/dts/tegra186-p2771-0000.dtsi

@@ -10,14 +10,63 @@
 
 	aliases {
 		sdhci0 = "/sdhci@3460000";
+		sdhci1 = "/sdhci@3400000";
+		i2c0 = "/bpmp/i2c";
+		i2c1 = "/i2c@3160000";
+		i2c2 = "/i2c@c240000";
+		i2c3 = "/i2c@3180000";
+		i2c4 = "/i2c@3190000";
+		i2c5 = "/i2c@31c0000";
+		i2c6 = "/i2c@c250000";
+		i2c7 = "/i2c@31e0000";
 	};
 
 	memory {
 		reg = <0x0 0x80000000 0x0 0x60000000>;
 	};
 
+	i2c@3160000 {
+		status = "okay";
+	};
+
+	i2c@3180000 {
+		status = "okay";
+	};
+
+	i2c@3190000 {
+		status = "okay";
+	};
+
+	i2c@31c0000 {
+		status = "okay";
+	};
+
+	sdhci@3400000 {
+		status = "okay";
+		wp-gpios = <&gpio_main TEGRA_MAIN_GPIO(P, 4) GPIO_ACTIVE_HIGH>;
+		bus-width = <4>;
+	};
+
 	sdhci@3460000 {
 		status = "okay";
 		bus-width = <8>;
 	};
+
+	i2c@c240000 {
+		status = "okay";
+	};
+
+	i2c@c250000 {
+		status = "okay";
+	};
+
+	i2c@31e0000 {
+		status = "okay";
+	};
+
+	bpmp {
+		i2c {
+			status = "okay";
+		};
+	};
 };

arch/arm/dts/tegra186.dtsi

@@ -1,14 +1,18 @@
 #include "skeleton.dtsi"
+#include <dt-bindings/clock/tegra186-clock.h>
 #include <dt-bindings/gpio/tegra186-gpio.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/mailbox/tegra-hsp.h>
+#include <dt-bindings/mailbox/tegra186-hsp.h>
+#include <dt-bindings/power/tegra186-powergate.h>
+#include <dt-bindings/reset/tegra186-reset.h>
 
 / {
 	compatible = "nvidia,tegra186";
+	interrupt-parent = <&gic>;
 	#address-cells = <2>;
 	#size-cells = <2>;
 
-	gpio@2200000 {
+	gpio_main: gpio@2200000 {
 		compatible = "nvidia,tegra186-gpio";
 		reg-names = "security", "gpio";
 		reg =
@@ -34,26 +38,154 @@
 		status = "disabled";
 	};
 
+	gen1_i2c: i2c@3160000 {
+		compatible = "nvidia,tegra186-i2c", "nvidia,tegra114-i2c";
+		reg = <0x0 0x3160000 0x0 0x100>;
+		interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&bpmp TEGRA186_CLK_I2C1>;
+		clock-names = "i2c";
+		resets = <&bpmp TEGRA186_RESET_I2C1>;
+		reset-names = "i2c";
+		status = "disabled";
+	};
+
+	cam_i2c: i2c@3180000 {
+		compatible = "nvidia,tegra186-i2c", "nvidia,tegra114-i2c";
+		reg = <0x0 0x3180000 0x0 0x100>;
+		interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&bpmp TEGRA186_CLK_I2C3>;
+		clock-names = "i2c";
+		resets = <&bpmp TEGRA186_RESET_I2C3>;
+		reset-names = "i2c";
+		status = "disabled";
+	};
+
+	dp_aux_ch1_i2c: i2c@3190000 {
+		compatible = "nvidia,tegra186-i2c", "nvidia,tegra114-i2c";
+		reg = <0x0 0x3190000 0x0 0x100>;
+		interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&bpmp TEGRA186_CLK_I2C4>;
+		clock-names = "i2c";
+		resets = <&bpmp TEGRA186_RESET_I2C4>;
+		reset-names = "i2c";
+		status = "disabled";
+	};
+
+	dp_aux_ch0_i2c: i2c@31b0000 {
+		compatible = "nvidia,tegra186-i2c", "nvidia,tegra114-i2c";
+		reg = <0x0 0x31b0000 0x0 0x100>;
+		interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&bpmp TEGRA186_CLK_I2C6>;
+		clock-names = "i2c";
+		resets = <&bpmp TEGRA186_RESET_I2C6>;
+		reset-names = "i2c";
+		status = "disabled";
+	};
+
+	gen7_i2c: i2c@31c0000 {
+		compatible = "nvidia,tegra186-i2c", "nvidia,tegra114-i2c";
+		reg = <0x0 0x31c0000 0x0 0x100>;
+		interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&bpmp TEGRA186_CLK_I2C7>;
+		clock-names = "i2c";
+		resets = <&bpmp TEGRA186_RESET_I2C7>;
+		reset-names = "i2c";
+		status = "disabled";
+	};
+
+	gen9_i2c: i2c@31e0000 {
+		compatible = "nvidia,tegra186-i2c", "nvidia,tegra114-i2c";
+		reg = <0x0 0x31e0000 0x0 0x100>;
+		interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&bpmp TEGRA186_CLK_I2C9>;
+		clock-names = "i2c";
+		resets = <&bpmp TEGRA186_RESET_I2C9>;
+		reset-names = "i2c";
+		status = "disabled";
+	};
+
+	sdhci@3400000 {
+		compatible = "nvidia,tegra186-sdhci";
+		reg = <0x0 0x03400000 0x0 0x200>;
+		resets = <&bpmp TEGRA186_RESET_SDMMC1>;
+		reset-names = "sdmmc";
+		clocks = <&bpmp TEGRA186_CLK_SDMMC1>;
+		clock-names = "sdmmc";
+		interrupts = <GIC_SPI 62 0x04>;
+		status = "disabled";
+	};
+
 	sdhci@3460000 {
 		compatible = "nvidia,tegra186-sdhci";
 		reg = <0x0 0x03460000 0x0 0x200>;
+		resets = <&bpmp TEGRA186_RESET_SDMMC4>;
+		reset-names = "sdmmc";
+		clocks = <&bpmp TEGRA186_CLK_SDMMC4>;
+		clock-names = "sdmmc";
 		interrupts = <GIC_SPI 31 0x04>;
 		status = "disabled";
 	};
 
+	gic: interrupt-controller@3881000 {
+		compatible = "arm,gic-400";
+		#interrupt-cells = <3>;
+		interrupt-controller;
+		reg = <0x0 0x3881000 0x0 0x1000>,
+		      <0x0 0x3882000 0x0 0x2000>,
+		      <0x0 0x3884000 0x0 0x2000>,
+		      <0x0 0x3886000 0x0 0x2000>;
+		interrupts = <GIC_PPI 9
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+		interrupt-parent = <&gic>;
+	};
+
 	hsp: hsp@3c00000 {
 		compatible = "nvidia,tegra186-hsp";
 		reg = <0x0 0x03c00000 0x0 0xa0000>;
 		interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>;
-		nvidia,num-SM = <0x8>;
-		nvidia,num-AS = <0x2>;
-		nvidia,num-SS = <0x2>;
-		nvidia,num-DB = <0x7>;
-		nvidia,num-SI = <0x8>;
-		#mbox-cells = <1>;
+		interrupt-names = "doorbell";
+		#mbox-cells = <2>;
 	};
 
-	gpio@c2f0000 {
+	gen2_i2c: i2c@c240000 {
+		compatible = "nvidia,tegra186-i2c", "nvidia,tegra114-i2c";
+		reg = <0x0 0xc240000 0x0 0x100>;
+		interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&bpmp TEGRA186_CLK_I2C2>;
+		clock-names = "i2c";
+		resets = <&bpmp TEGRA186_RESET_I2C2>;
+		reset-names = "i2c";
+		status = "disabled";
+	};
+
+	gen8_i2c: i2c@c250000 {
+		compatible = "nvidia,tegra186-i2c", "nvidia,tegra114-i2c";
+		reg = <0x0 0xc250000 0x0 0x100>;
+		interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&bpmp TEGRA186_CLK_I2C8>;
+		clock-names = "i2c";
+		resets = <&bpmp TEGRA186_RESET_I2C8>;
+		reset-names = "i2c";
+		status = "disabled";
+	};
+
+	gpio_aon: gpio@c2f0000 {
 		compatible = "nvidia,tegra186-gpio-aon";
 		reg-names = "security", "gpio";
 		reg =
@@ -66,4 +198,124 @@
 		interrupt-controller;
 		#interrupt-cells = <2>;
 	};
+
+	pcie-controller@10003000 {
+		compatible = "nvidia,tegra186-pcie";
+		device_type = "pci";
+		reg = <0x0 0x10003000 0x0 0x00000800   /* PADS registers */
+		       0x0 0x10003800 0x0 0x00000800   /* AFI registers */
+		       0x0 0x40000000 0x0 0x10000000>; /* configuration space */
+		reg-names = "pads", "afi", "cs";
+		interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */
+			     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>, /* MSI interrupt */
+			     <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; /* Wake interrupt */
+		interrupt-names = "intr", "msi", "wake";
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 0>;
+		interrupt-map = <0 0 0 0 &gic GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+
+		bus-range = <0x00 0xff>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+
+		ranges = <0x82000000 0 0x10000000 0x0 0x10000000 0 0x00001000   /* port 0 configuration space */
+			  0x82000000 0 0x10001000 0x0 0x10001000 0 0x00001000   /* port 1 configuration space */
+			  0x82000000 0 0x10004000 0x0 0x10004000 0 0x00001000   /* port 2 configuration space */
+			  0x81000000 0 0x0        0x0 0x50000000 0 0x00010000   /* downstream I/O (64 KiB) */
+			  0x82000000 0 0x50100000 0x0 0x50100000 0 0x07f00000   /* non-prefetchable memory (127 MiB) */
+			  0xc2000000 0 0x58000000 0x0 0x58000000 0 0x28000000>; /* prefetchable memory (640 MiB) */
+
+		clocks = <&bpmp TEGRA186_CLK_PCIE>,
+			 <&bpmp TEGRA186_CLK_AFI>;
+		clock-names = "pex", "afi";
+		resets = <&bpmp TEGRA186_RESET_PCIE>,
+			 <&bpmp TEGRA186_RESET_AFI>,
+			 <&bpmp TEGRA186_RESET_PCIEXCLK>;
+		reset-names = "pex", "afi", "pcie_x";
+		power-domains = <&bpmp TEGRA186_POWER_DOMAIN_PCX>;
+		status = "disabled";
+
+		pci@1,0 {
+			device_type = "pci";
+			assigned-addresses = <0x82000800 0 0x10000000 0 0x1000>;
+			reg = <0x000800 0 0 0 0>;
+			status = "disabled";
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+			ranges;
+
+			nvidia,num-lanes = <2>;
+		};
+
+		pci@2,0 {
+			device_type = "pci";
+			assigned-addresses = <0x82001000 0 0x10001000 0 0x1000>;
+			reg = <0x001000 0 0 0 0>;
+			status = "disabled";
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+			ranges;
+
+			nvidia,num-lanes = <1>;
+		};
+
+		pci@3,0 {
+			device_type = "pci";
+			assigned-addresses = <0x82001800 0 0x10004000 0 0x1000>;
+			reg = <0x001800 0 0 0 0>;
+			status = "disabled";
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+			ranges;
+
+			nvidia,num-lanes = <1>;
+		};
+	};
+
+	sysram@30000000 {
+		compatible = "nvidia,tegra186-sysram", "mmio-sram";
+		reg = <0x0 0x30000000 0x0 0x50000>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges = <0 0x0 0x0 0x30000000 0x0 0x50000>;
+
+		sysram_cpu_bpmp_tx: shmem@4e000 {
+			compatible = "nvidia,tegra186-bpmp-shmem";
+			reg = <0x0 0x4e000 0x0 0x1000>;
+		};
+
+		sysram_cpu_bpmp_rx: shmem@4f000 {
+			compatible = "nvidia,tegra186-bpmp-shmem";
+			reg = <0x0 0x4f000 0x0 0x1000>;
+		};
+	};
+
+	bpmp: bpmp {
+		compatible = "nvidia,tegra186-bpmp";
+		mboxes = <&hsp HSP_MBOX_TYPE_DB HSP_DB_MASTER_BPMP>;
+		/*
+		 * In theory, these references, and the configuration in the
+		 * node these reference point at, are board-specific, since
+		 * they depend on the BCT's memory carve-out setup, the
+		 * firmware that's actually loaded onto the BPMP, etc. However,
+		 * in practice, all boards are likely to use identical values.
+		 */
+		shmem = <&sysram_cpu_bpmp_tx &sysram_cpu_bpmp_rx>;
+		#clock-cells = <1>;
+		#power-domain-cells = <1>;
+		#reset-cells = <1>;
+
+		bpmp_i2c: i2c {
+			compatible = "nvidia,tegra186-bpmp-i2c";
+			nvidia,bpmp = <&bpmp>;
+			nvidia,bpmp-bus-id = <5>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+	};
 };

arch/arm/dts/zynqmp-clk.dtsi

@@ -13,6 +13,7 @@
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <100000000>;
+		u-boot,dm-pre-reloc;
 	};
 
 	clk125: clk125 {

arch/arm/dts/zynqmp-ep108-clk.dtsi

@@ -13,6 +13,7 @@
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <25000000>;
+		u-boot,dm-pre-reloc;
 	};
 
 	i2c_clk: i2c_clk {

arch/arm/include/asm/arch-fsl-layerscape/config.h

@@ -149,43 +149,43 @@
 #define CONFIG_ARM_ERRATA_833471
 
 #define CONFIG_SYS_FSL_MAX_NUM_OF_SEC		1
-#elif defined(CONFIG_LS1043A)
-#define CONFIG_MAX_CPUS				4
+#elif defined(CONFIG_FSL_LSCH2)
 #define CONFIG_SYS_CACHELINE_SIZE		64
+#define CONFIG_NUM_DDR_CONTROLLERS		1
+#define CONFIG_SYS_FSL_SEC_COMPAT		5
+#define CONFIG_SYS_FSL_OCRAM_BASE		0x10000000 /* initial RAM */
+#define CONFIG_SYS_FSL_OCRAM_SIZE		0x00200000 /* 2M */
+#define CONFIG_SYS_CCSRBAR_DEFAULT		0x01000000
+
+#define CONFIG_SYS_FSL_CCSR_SCFG_BE
+#define CONFIG_SYS_FSL_ESDHC_BE
+#define CONFIG_SYS_FSL_WDOG_BE
+#define CONFIG_SYS_FSL_DSPI_BE
+#define CONFIG_SYS_FSL_QSPI_BE
+#define CONFIG_SYS_FSL_CCSR_GUR_BE
+#define CONFIG_SYS_FSL_PEX_LUT_BE
+#define CONFIG_SYS_FSL_SEC_BE
+
+#define CONFIG_SYS_FSL_SRDS_1
+/* SoC related */
+#ifdef CONFIG_LS1043A
+#define CONFIG_MAX_CPUS				4
 #define CONFIG_SYS_FMAN_V3
 #define CONFIG_SYS_NUM_FMAN			1
 #define CONFIG_SYS_NUM_FM1_DTSEC		7
 #define CONFIG_SYS_NUM_FM1_10GEC		1
 #define CONFIG_SYS_FSL_IFC_BANK_COUNT		4
-#define CONFIG_NUM_DDR_CONTROLLERS		1
-#define CONFIG_SYS_CCSRBAR_DEFAULT		0x01000000
-#define CONFIG_SYS_FSL_SEC_COMPAT		5
-#define CONFIG_SYS_FSL_OCRAM_BASE		0x10000000 /* initial RAM */
-#define CONFIG_SYS_FSL_OCRAM_SIZE		0x200000 /* 2 MiB */
 #define CONFIG_SYS_FSL_DDR_BE
 #define CONFIG_SYS_DDR_BLOCK1_SIZE		((phys_size_t)2 << 30)
 #define CONFIG_MAX_MEM_MAPPED			CONFIG_SYS_DDR_BLOCK1_SIZE
 
-#define CONFIG_SYS_FSL_CCSR_GUR_BE
-#define CONFIG_SYS_FSL_CCSR_SCFG_BE
-#define CONFIG_SYS_FSL_IFC_BE
-#define CONFIG_SYS_FSL_ESDHC_BE
-#define CONFIG_SYS_FSL_WDOG_BE
-#define CONFIG_SYS_FSL_DSPI_BE
-#define CONFIG_SYS_FSL_QSPI_BE
-#define CONFIG_SYS_FSL_PEX_LUT_BE
-
 #define QE_MURAM_SIZE		0x6000UL
 #define MAX_QE_RISC		1
 #define QE_NUM_OF_SNUM		28
 
-#define SRDS_MAX_LANES		4
-#define CONFIG_SYS_FSL_SRDS_1
-#define CONFIG_SYS_FSL_PCIE_COMPAT		"fsl,qoriq-pcie-v2.4"
-
+#define CONFIG_SYS_FSL_IFC_BE
 #define CONFIG_SYS_FSL_SFP_VER_3_2
 #define CONFIG_SYS_FSL_SEC_MON_BE
-#define CONFIG_SYS_FSL_SEC_BE
 #define CONFIG_SYS_FSL_SFP_BE
 #define CONFIG_SYS_FSL_SRK_LE
 #define CONFIG_KEY_REVOCATION
@@ -205,32 +205,40 @@
 #define CONFIG_SYS_FSL_MAX_NUM_OF_SEC		1
 #elif defined(CONFIG_LS1012A)
 #define CONFIG_MAX_CPUS                         1
-#define CONFIG_SYS_CACHELINE_SIZE		64
-#define CONFIG_NUM_DDR_CONTROLLERS		1
-#define CONFIG_SYS_CCSRBAR_DEFAULT		0x01000000
-#define CONFIG_SYS_FSL_SEC_COMPAT		5
 #undef	CONFIG_SYS_FSL_DDRC_ARM_GEN3
 
-#define CONFIG_SYS_FSL_OCRAM_BASE		0x10000000 /* initial RAM */
-#define CONFIG_SYS_FSL_OCRAM_SIZE		0x200000 /* 2 MiB */
-
 #define GICD_BASE		0x01401000
 #define GICC_BASE		0x01402000
+#elif defined(CONFIG_LS1046A)
+#define CONFIG_MAX_CPUS				4
+#define CONFIG_SYS_FMAN_V3
+#define CONFIG_SYS_NUM_FMAN			1
+#define CONFIG_SYS_NUM_FM1_DTSEC		8
+#define CONFIG_SYS_NUM_FM1_10GEC		2
+#define CONFIG_SYS_FSL_IFC_BANK_COUNT		4
+#define CONFIG_SYS_FSL_DDR_BE
+#define CONFIG_SYS_DDR_BLOCK1_SIZE  ((phys_size_t)2 << 30)
+#define CONFIG_MAX_MEM_MAPPED           CONFIG_SYS_DDR_BLOCK1_SIZE
 
-#define CONFIG_SYS_FSL_CCSR_GUR_BE
-#define CONFIG_SYS_FSL_CCSR_SCFG_BE
-#define CONFIG_SYS_FSL_ESDHC_BE
-#define CONFIG_SYS_FSL_WDOG_BE
-#define CONFIG_SYS_FSL_DSPI_BE
-#define CONFIG_SYS_FSL_QSPI_BE
-#define CONFIG_SYS_FSL_PEX_LUT_BE
+#define CONFIG_SYS_FSL_SRDS_2
+#define CONFIG_SYS_FSL_IFC_BE
+#define CONFIG_SYS_FSL_SFP_VER_3_2
+#define CONFIG_SYS_FSL_SNVS_LE
+#define CONFIG_SYS_FSL_SFP_BE
+#define CONFIG_SYS_FSL_SRK_LE
+#define CONFIG_KEY_REVOCATION
 
-#define SRDS_MAX_LANES		4
-#define CONFIG_SYS_FSL_SRDS_1
-#define CONFIG_SYS_FSL_PCIE_COMPAT		"fsl,qoriq-pcie-v2.4"
-#define CONFIG_SYS_FSL_SEC_BE
+/* SMMU Defintions */
+#define SMMU_BASE		0x09000000
+
+/* Generic Interrupt Controller Definitions */
+#define GICD_BASE		0x01410000
+#define GICC_BASE		0x01420000
+
+#define CONFIG_SYS_FSL_MAX_NUM_OF_SEC		1
 #else
 #error SoC not defined
 #endif
+#endif
 
 #endif /* _ASM_ARMV8_FSL_LAYERSCAPE_CONFIG_H_ */

arch/arm/include/asm/arch-fsl-layerscape/cpu.h

@@ -13,6 +13,8 @@ static struct cpu_type cpu_type_list[] = {
 	CPU_TYPE_ENTRY(LS2045A, LS2045A, 4),
 	CPU_TYPE_ENTRY(LS1043A, LS1043A, 4),
 	CPU_TYPE_ENTRY(LS1023A, LS1023A, 2),
+	CPU_TYPE_ENTRY(LS1046A, LS1046A, 4),
+	CPU_TYPE_ENTRY(LS1026A, LS1026A, 2),
 	CPU_TYPE_ENTRY(LS2040A, LS2040A, 4),
 	CPU_TYPE_ENTRY(LS1012A, LS1012A, 1),
 };

arch/arm/include/asm/arch-fsl-layerscape/fsl_serdes.h

@@ -140,6 +140,7 @@ enum srds_prtcl {
 
 enum srds {
 	FSL_SRDS_1  = 0,
+	FSL_SRDS_2  = 1,
 };
 
 #endif
@@ -150,7 +151,7 @@ int serdes_get_first_lane(u32 sd, enum srds_prtcl device);
 enum srds_prtcl serdes_get_prtcl(int serdes, int cfg, int lane);
 int is_serdes_prtcl_valid(int serdes, u32 prtcl);
 
-#ifdef	CONFIG_LS1043A
+#ifdef CONFIG_FSL_LSCH2
 const char *serdes_clock_to_string(u32 clock);
 int get_serdes_protocol(void);
 #endif

arch/arm/include/asm/arch-fsl-layerscape/immap_lsch2.h

@@ -31,9 +31,9 @@
 #define CONFIG_SYS_NS16550_COM2			(CONFIG_SYS_IMMR + 0x011c0600)
 #define CONFIG_SYS_NS16550_COM3			(CONFIG_SYS_IMMR + 0x011d0500)
 #define CONFIG_SYS_NS16550_COM4			(CONFIG_SYS_IMMR + 0x011d0600)
-#define CONFIG_SYS_LS1043A_XHCI_USB1_ADDR	(CONFIG_SYS_IMMR + 0x01f00000)
-#define CONFIG_SYS_LS1043A_XHCI_USB2_ADDR	(CONFIG_SYS_IMMR + 0x02000000)
-#define CONFIG_SYS_LS1043A_XHCI_USB3_ADDR	(CONFIG_SYS_IMMR + 0x02100000)
+#define CONFIG_SYS_XHCI_USB1_ADDR		(CONFIG_SYS_IMMR + 0x01f00000)
+#define CONFIG_SYS_XHCI_USB2_ADDR		(CONFIG_SYS_IMMR + 0x02000000)
+#define CONFIG_SYS_XHCI_USB3_ADDR		(CONFIG_SYS_IMMR + 0x02100000)
 #define CONFIG_SYS_PCIE1_ADDR			(CONFIG_SYS_IMMR + 0x2400000)
 #define CONFIG_SYS_PCIE2_ADDR			(CONFIG_SYS_IMMR + 0x2500000)
 #define CONFIG_SYS_PCIE3_ADDR			(CONFIG_SYS_IMMR + 0x2600000)
@@ -94,6 +94,7 @@
 #define TY_ITYP_VER_A7          0x1
 #define TY_ITYP_VER_A53         0x2
 #define TY_ITYP_VER_A57         0x3
+#define TY_ITYP_VER_A72		0x4
 
 #define TP_CLUSTER_EOC		0xc0000000      /* end of clusters */
 #define TP_CLUSTER_INIT_MASK    0x0000003f      /* initiator mask */
@@ -227,6 +228,8 @@ struct ccsr_gur {
 #define FSL_CHASSIS2_RCWSR0_MEM_PLL_RAT_MASK	0x3f
 #define FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_MASK	0xffff0000
 #define FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_SHIFT	16
+#define FSL_CHASSIS2_RCWSR4_SRDS2_PRTCL_MASK	0x0000ffff
+#define FSL_CHASSIS2_RCWSR4_SRDS2_PRTCL_SHIFT	0
 #define RCW_SB_EN_REG_INDEX	7
 #define RCW_SB_EN_MASK		0x00200000
 

arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h

@@ -52,8 +52,8 @@
 #define I2C3_BASE_ADDR				(CONFIG_SYS_IMMR + 0x01020000)
 #define I2C4_BASE_ADDR				(CONFIG_SYS_IMMR + 0x01030000)
 
-#define CONFIG_SYS_LS2080A_XHCI_USB1_ADDR	(CONFIG_SYS_IMMR + 0x02100000)
-#define CONFIG_SYS_LS2080A_XHCI_USB2_ADDR	(CONFIG_SYS_IMMR + 0x02110000)
+#define CONFIG_SYS_XHCI_USB1_ADDR		(CONFIG_SYS_IMMR + 0x02100000)
+#define CONFIG_SYS_XHCI_USB2_ADDR		(CONFIG_SYS_IMMR + 0x02110000)
 
 /* TZ Address Space Controller Definitions */
 #define TZASC1_BASE			0x01100000	/* as per CCSR map. */
@@ -156,6 +156,7 @@
 #define TY_ITYP_VER_A7		0x1
 #define TY_ITYP_VER_A53		0x2
 #define TY_ITYP_VER_A57		0x3
+#define TY_ITYP_VER_A72		0x4
 
 #define TP_CLUSTER_EOC		0x80000000	/* end of clusters */
 #define TP_CLUSTER_INIT_MASK	0x0000003f	/* initiator mask */

arch/arm/include/asm/arch-fsl-layerscape/soc.h

@@ -44,6 +44,8 @@ struct cpu_type {
 #define SVR_LS1012A		0x870400
 #define SVR_LS1043A		0x879200
 #define SVR_LS1023A		0x879208
+#define SVR_LS1046A		0x870700
+#define SVR_LS1026A		0x870708
 #define SVR_LS2045A		0x870120
 #define SVR_LS2080A		0x870110
 #define SVR_LS2085A		0x870100

arch/arm/include/asm/arch-ls102xa/config.h

@@ -10,7 +10,7 @@
 #define CONFIG_SYS_CACHELINE_SIZE		64
 
 #define OCRAM_BASE_ADDR				0x10000000
-#define OCRAM_SIZE				0x00020000
+#define OCRAM_SIZE				0x00010000
 #define OCRAM_BASE_S_ADDR			0x10010000
 #define OCRAM_S_SIZE				0x00010000
 
@@ -32,16 +32,15 @@
 #define CONFIG_SYS_FSL_SERDES_ADDR		(CONFIG_SYS_IMMR + 0x00ea0000)
 #define CONFIG_SYS_FSL_GUTS_ADDR		(CONFIG_SYS_IMMR + 0x00ee0000)
 #define CONFIG_SYS_FSL_LS1_CLK_ADDR		(CONFIG_SYS_IMMR + 0x00ee1000)
+#define CONFIG_SYS_FSL_RCPM_ADDR		(CONFIG_SYS_IMMR + 0x00ee2000)
 #define CONFIG_SYS_NS16550_COM1			(CONFIG_SYS_IMMR + 0x011c0500)
 #define CONFIG_SYS_NS16550_COM2			(CONFIG_SYS_IMMR + 0x011d0500)
 #define CONFIG_SYS_DCU_ADDR			(CONFIG_SYS_IMMR + 0x01ce0000)
-#define CONFIG_SYS_LS102XA_XHCI_USB1_ADDR	(CONFIG_SYS_IMMR + 0x02100000)
-#define CONFIG_SYS_LS102XA_USB1_ADDR \
-	(CONFIG_SYS_IMMR + CONFIG_SYS_LS102XA_USB1_OFFSET)
+#define CONFIG_SYS_XHCI_USB1_ADDR		(CONFIG_SYS_IMMR + 0x02100000)
+#define CONFIG_SYS_EHCI_USB1_ADDR		(CONFIG_SYS_IMMR + 0x07600000)
 
 #define CONFIG_SYS_FSL_SEC_OFFSET		0x00700000
 #define CONFIG_SYS_FSL_JR0_OFFSET		0x00710000
-#define CONFIG_SYS_LS102XA_USB1_OFFSET		0x07600000
 #define CONFIG_SYS_TSEC1_OFFSET			0x01d10000
 #define CONFIG_SYS_TSEC2_OFFSET			0x01d50000
 #define CONFIG_SYS_TSEC3_OFFSET			0x01d90000

arch/arm/include/asm/arch-omap4/i2c.h

@@ -14,9 +14,9 @@ struct i2c {
 	unsigned short revnb_lo;	/* 0x00 */
 	unsigned short res1;
 	unsigned short revnb_hi;	/* 0x04 */
-	unsigned short res2[13];
-	unsigned short sysc;		/* 0x20 */
-	unsigned short res3;
+	unsigned short res2[5];
+	unsigned short sysc;		/* 0x10 */
+	unsigned short res3[9];
 	unsigned short irqstatus_raw;	/* 0x24 */
 	unsigned short res4;
 	unsigned short stat;		/* 0x28 */

arch/arm/include/asm/arch-omap5/i2c.h

@@ -14,9 +14,9 @@ struct i2c {
 	unsigned short revnb_lo;	/* 0x00 */
 	unsigned short res1;
 	unsigned short revnb_hi;	/* 0x04 */
-	unsigned short res2[13];
-	unsigned short sysc;		/* 0x20 */
-	unsigned short res3;
+	unsigned short res2[5];
+	unsigned short sysc;		/* 0x10 */
+	unsigned short res3[9];
 	unsigned short irqstatus_raw;	/* 0x24 */
 	unsigned short res4;
 	unsigned short stat;		/* 0x28 */

arch/arm/include/asm/arch-rockchip/clock.h

@@ -65,6 +65,8 @@ void *rockchip_get_cru(void);
 struct rk3288_cru;
 struct rk3288_grf;
 
-void rkclk_configure_cpu(struct rk3288_cru *cru, struct rk3288_grf *grf);
+void rk3288_clk_configure_cpu(struct rk3288_cru *cru, struct rk3288_grf *grf);
+
+int rockchip_get_clk(struct udevice **devp);
 
 #endif

arch/arm/include/asm/arch-rockchip/cru_rk3399.h

@@ -0,0 +1,93 @@
+/*
+ * (C) Copyright 2016 Rockchip Electronics Co., Ltd
+ *
+ * SPDX-License-Identifier:     GPL-2.0+
+ */
+
+#ifndef __ASM_ARCH_CRU_RK3399_H_
+#define __ASM_ARCH_CRU_RK3399_H_
+
+#include <common.h>
+
+struct rk3399_pmucru {
+	u32 ppll_con[6];
+	u32 reserved[0x1a];
+	u32 pmucru_clksel[6];
+	u32 pmucru_clkfrac_con[2];
+	u32 reserved2[0x18];
+	u32 pmucru_clkgate_con[3];
+	u32 reserved3;
+	u32 pmucru_softrst_con[2];
+	u32 reserved4[2];
+	u32 pmucru_rstnhold_con[2];
+	u32 reserved5[2];
+	u32 pmucru_gatedis_con[2];
+};
+check_member(rk3399_pmucru, pmucru_gatedis_con[1], 0x134);
+
+struct rk3399_cru {
+	u32 apll_l_con[6];
+	u32 reserved[2];
+	u32 apll_b_con[6];
+	u32 reserved1[2];
+	u32 dpll_con[6];
+	u32 reserved2[2];
+	u32 cpll_con[6];
+	u32 reserved3[2];
+	u32 gpll_con[6];
+	u32 reserved4[2];
+	u32 npll_con[6];
+	u32 reserved5[2];
+	u32 vpll_con[6];
+	u32 reserved6[0x0a];
+	u32 clksel_con[108];
+	u32 reserved7[0x14];
+	u32 clkgate_con[35];
+	u32 reserved8[0x1d];
+	u32 softrst_con[21];
+	u32 reserved9[0x2b];
+	u32 glb_srst_fst_value;
+	u32 glb_srst_snd_value;
+	u32 glb_cnt_th;
+	u32 misc_con;
+	u32 glb_rst_con;
+	u32 glb_rst_st;
+	u32 reserved10[0x1a];
+	u32 sdmmc_con[2];
+	u32 sdio0_con[2];
+	u32 sdio1_con[2];
+};
+check_member(rk3399_cru, sdio1_con[1], 0x594);
+#define MHz		1000000
+#define KHz		1000
+#define OSC_HZ		(24*MHz)
+#define APLL_HZ		(600*MHz)
+#define GPLL_HZ		(594*MHz)
+#define CPLL_HZ		(384*MHz)
+#define PPLL_HZ		(594*MHz)
+
+#define PMU_PCLK_HZ	(99*MHz)
+
+#define ACLKM_CORE_HZ	(300*MHz)
+#define ATCLK_CORE_HZ	(300*MHz)
+#define PCLK_DBG_HZ	(100*MHz)
+
+#define PERIHP_ACLK_HZ	(148500*KHz)
+#define PERIHP_HCLK_HZ	(148500*KHz)
+#define PERIHP_PCLK_HZ	(37125*KHz)
+
+#define PERILP0_ACLK_HZ	(99000*KHz)
+#define PERILP0_HCLK_HZ	(99000*KHz)
+#define PERILP0_PCLK_HZ	(49500*KHz)
+
+#define PERILP1_HCLK_HZ	(99000*KHz)
+#define PERILP1_PCLK_HZ	(49500*KHz)
+
+#define PWM_CLOCK_HZ    PMU_PCLK_HZ
+
+enum apll_l_frequencies {
+	APLL_L_1600_MHZ,
+	APLL_L_600_MHZ,
+};
+
+#endif	/* __ASM_ARCH_CRU_RK3399_H_ */

arch/arm/include/asm/arch-tegra/tegra_mmc.h

@@ -9,6 +9,9 @@
 #ifndef __TEGRA_MMC_H_
 #define __TEGRA_MMC_H_
 
+#include <common.h>
+#include <clk.h>
+#include <reset.h>
 #include <fdtdec.h>
 #include <asm/gpio.h>
 
@@ -134,7 +137,10 @@ struct mmc_host {
 	int id;			/* device id/number, 0-3 */
 	int enabled;		/* 1 to enable, 0 to disable */
 	int width;		/* Bus Width, 1, 4 or 8 */
-#ifndef CONFIG_TEGRA186
+#ifdef CONFIG_TEGRA186
+	struct reset_ctl reset_ctl;
+	struct clk clk;
+#else
 	enum periph_id mmc_id;	/* Peripheral ID: PERIPH_ID_... */
 #endif
 	struct gpio_desc cd_gpio;	/* Change Detect GPIO */

arch/arm/include/asm/barriers.h

@@ -30,15 +30,22 @@
 
 #endif /* !CONFIG_ARM64 */
 
-#if defined(__ARM_ARCH_7A__) || defined(CONFIG_ARM64)
+#if __LINUX_ARM_ARCH__ >= 7
 #define ISB	asm volatile ("isb sy" : : : "memory")
 #define DSB	asm volatile ("dsb sy" : : : "memory")
 #define DMB	asm volatile ("dmb sy" : : : "memory")
-#else
+#elif __LINUX_ARM_ARCH__ == 6
 #define ISB	CP15ISB
 #define DSB	CP15DSB
 #define DMB	CP15DMB
+#else
+#define ISB	asm volatile ("" : : : "memory")
+#define DSB	CP15DSB
+#define DMB	asm volatile ("" : : : "memory")
 #endif
 
+#define isb()	ISB
+#define dsb()	DSB
+#define dmb()	DMB
 #endif	/* __ASSEMBLY__ */
 #endif	/* __BARRIERS_H__ */

arch/arm/include/asm/config.h

@@ -11,7 +11,6 @@
 #define CONFIG_SYS_BOOT_RAMDISK_HIGH
 
 #ifdef CONFIG_ARM64
-#define CONFIG_PHYS_64BIT
 #define CONFIG_STATIC_RELA
 #endif
 

arch/arm/include/asm/fsl_secure_boot.h

@@ -17,8 +17,6 @@
 
 #ifdef CONFIG_CHAIN_OF_TRUST
 #define CONFIG_CMD_ESBC_VALIDATE
-#define CONFIG_CMD_BLOB
-#define CONFIG_CMD_HASH
 #define CONFIG_FSL_SEC_MON
 #define CONFIG_SHA_HW_ACCEL
 #define CONFIG_SHA_PROG_HW_ACCEL
@@ -28,6 +26,28 @@
 #define CONFIG_FSL_CAAM
 #endif
 
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SPL_BOARD_INIT
+#define CONFIG_SPL_DM			1
+#define CONFIG_SPL_CRYPTO_SUPPORT
+#define CONFIG_SPL_HASH_SUPPORT
+#define CONFIG_SPL_RSA
+#define CONFIG_SPL_DRIVERS_MISC_SUPPORT
+/*
+ * Define the key hash for U-Boot here if public/private key pair used to
+ * sign U-boot are different from the SRK hash put in the fuse
+ * Example of defining KEY_HASH is
+ * #define CONFIG_SPL_UBOOT_KEY_HASH \
+ *      "41066b564c6ffcef40ccbc1e0a5d0d519604000c785d97bbefd25e4d288d1c8b"
+ * else leave it defined as NULL
+ */
+
+#define CONFIG_SPL_UBOOT_KEY_HASH	NULL
+#endif /* ifdef CONFIG_SPL_BUILD */
+
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_CMD_BLOB
+#define CONFIG_CMD_HASH
 #define CONFIG_KEY_REVOCATION
 #ifndef CONFIG_SYS_RAMBOOT
 /* The key used for verification of next level images
@@ -58,39 +78,55 @@
 	"setenv hwconfig \'fsl_ddr:ctlr_intlv=null,bank_intlv=null\';"
 #else
 #define CONFIG_EXTRA_ENV \
-	"setenv fdt_high 0xcfffffff;"	\
-	"setenv initrd_high 0xcfffffff;"	\
+	"setenv fdt_high 0xffffffff;"	\
+	"setenv initrd_high 0xffffffff;"	\
 	"setenv hwconfig \'fsl_ddr:ctlr_intlv=null,bank_intlv=null\';"
 #endif
 
 /* Copying Bootscript and Header to DDR from NOR for LS2 and for rest, from
  * Non-XIP Memory (Nand/SD)*/
-#if defined(CONFIG_SYS_RAMBOOT) || defined(CONFIG_LS2080A)
+#if defined(CONFIG_SYS_RAMBOOT) || defined(CONFIG_LS2080A) || \
+	defined(CONFIG_SD_BOOT)
 #define CONFIG_BOOTSCRIPT_COPY_RAM
 #endif
-/* The address needs to be modified according to NOR and DDR memory map */
+/* The address needs to be modified according to NOR, NAND, SD and
+ * DDR memory map
+ */
 #ifdef CONFIG_LS2080A
-#define CONFIG_BS_HDR_ADDR_FLASH	0x583920000
-#define CONFIG_BS_ADDR_FLASH		0x583900000
+#define CONFIG_BS_HDR_ADDR_DEVICE	0x583920000
+#define CONFIG_BS_ADDR_DEVICE		0x583900000
 #define CONFIG_BS_HDR_ADDR_RAM		0xa3920000
 #define CONFIG_BS_ADDR_RAM		0xa3900000
+#define CONFIG_BS_HDR_SIZE		0x00002000
+#define CONFIG_BS_SIZE			0x00001000
 #else
-#define CONFIG_BS_HDR_ADDR_FLASH	0x600a0000
-#define CONFIG_BS_ADDR_FLASH		0x60060000
-#define CONFIG_BS_HDR_ADDR_RAM		0xa0060000
-#define CONFIG_BS_ADDR_RAM		0xa0060000
+#ifdef CONFIG_SD_BOOT
+/* For SD boot address and size are assigned in terms of sector
+ * offset and no. of sectors respectively.
+ */
+#define CONFIG_BS_HDR_ADDR_DEVICE	0x00000800
+#define CONFIG_BS_ADDR_DEVICE		0x00000840
+#define CONFIG_BS_HDR_SIZE		0x00000010
+#define CONFIG_BS_SIZE			0x00000008
+#else
+#define CONFIG_BS_HDR_ADDR_DEVICE	0x600a0000
+#define CONFIG_BS_ADDR_DEVICE		0x60060000
+#define CONFIG_BS_HDR_SIZE		0x00002000
+#define CONFIG_BS_SIZE			0x00001000
+#endif /* #ifdef CONFIG_SD_BOOT */
+#define CONFIG_BS_HDR_ADDR_RAM		0x81000000
+#define CONFIG_BS_ADDR_RAM		0x81020000
 #endif
 
 #ifdef CONFIG_BOOTSCRIPT_COPY_RAM
 #define CONFIG_BOOTSCRIPT_HDR_ADDR	CONFIG_BS_HDR_ADDR_RAM
-#define CONFIG_BS_HDR_SIZE		0x00002000
 #define CONFIG_BOOTSCRIPT_ADDR		CONFIG_BS_ADDR_RAM
-#define CONFIG_BS_SIZE			0x00001000
 #else
-#define CONFIG_BOOTSCRIPT_HDR_ADDR	CONFIG_BS_HDR_ADDR_FLASH
-/* BS_HDR_SIZE, BOOTSCRIPT_ADDR and BS_SIZE are not required */
+#define CONFIG_BOOTSCRIPT_HDR_ADDR	CONFIG_BS_HDR_ADDR_DEVICE
+/* BOOTSCRIPT_ADDR is not required */
 #endif
 
 #include <config_fsl_chain_trust.h>
+#endif /* #ifndef CONFIG_SPL_BUILD */
 #endif /* #ifdef CONFIG_CHAIN_OF_TRUST */
 #endif

arch/arm/include/asm/io.h

@@ -25,6 +25,7 @@
 #include <linux/types.h>
 #include <asm/byteorder.h>
 #include <asm/memory.h>
+#include <asm/barriers.h>
 #if 0	/* XXX###XXX */
 #include <asm/arch/hardware.h>
 #endif	/* XXX###XXX */
@@ -136,8 +137,7 @@ static inline void __raw_readsl(unsigned long addr, void *data, int longlen)
  * TODO: The kernel offers some more advanced versions of barriers, it might
  * have some advantages to use them instead of the simple one here.
  */
-#define mb()		asm volatile("dsb sy" : : : "memory")
-#define dmb()		__asm__ __volatile__ ("" : : : "memory")
+#define mb()		dsb()
 #define __iormb()	dmb()
 #define __iowmb()	dmb()
 

arch/arm/include/asm/psci.h

@@ -18,6 +18,9 @@
 #ifndef __ARM_PSCI_H__
 #define __ARM_PSCI_H__
 
+#define ARM_PSCI_VER_1_0		(0x00010000)
+#define ARM_PSCI_VER_0_2		(0x00000002)
+
 /* PSCI 0.1 interface */
 #define ARM_PSCI_FN_BASE		0x95c1ba5e
 #define ARM_PSCI_FN(n)			(ARM_PSCI_FN_BASE + (n))
@@ -31,6 +34,12 @@
 #define ARM_PSCI_RET_NI			(-1)
 #define ARM_PSCI_RET_INVAL		(-2)
 #define ARM_PSCI_RET_DENIED		(-3)
+#define ARM_PSCI_RET_ALREADY_ON		(-4)
+#define ARM_PSCI_RET_ON_PENDING		(-5)
+#define ARM_PSCI_RET_INTERNAL_FAILURE	(-6)
+#define ARM_PSCI_RET_NOT_PRESENT	(-7)
+#define ARM_PSCI_RET_DISABLED		(-8)
+#define ARM_PSCI_RET_INVALID_ADDRESS	(-9)
 
 /* PSCI 0.2 interface */
 #define ARM_PSCI_0_2_FN_BASE			0x84000000
@@ -47,10 +56,25 @@
 #define ARM_PSCI_0_2_FN_SYSTEM_OFF		ARM_PSCI_0_2_FN(8)
 #define ARM_PSCI_0_2_FN_SYSTEM_RESET		ARM_PSCI_0_2_FN(9)
 
+/* PSCI 1.0 interface */
+#define ARM_PSCI_1_0_FN_PSCI_FEATURES		ARM_PSCI_0_2_FN(10)
+#define ARM_PSCI_1_0_FN_CPU_FREEZE		ARM_PSCI_0_2_FN(11)
+#define ARM_PSCI_1_0_FN_CPU_DEFAULT_SUSPEND	ARM_PSCI_0_2_FN(12)
+#define ARM_PSCI_1_0_FN_NODE_HW_STATE		ARM_PSCI_0_2_FN(13)
+#define ARM_PSCI_1_0_FN_SYSTEM_SUSPEND		ARM_PSCI_0_2_FN(14)
+#define ARM_PSCI_1_0_FN_SET_SUSPEND_MODE	ARM_PSCI_0_2_FN(15)
+#define ARM_PSCI_1_0_FN_STAT_RESIDENCY		ARM_PSCI_0_2_FN(16)
+#define ARM_PSCI_1_0_FN_STAT_COUNT		ARM_PSCI_0_2_FN(17)
+
 /* 1KB stack per core */
 #define ARM_PSCI_STACK_SHIFT	10
 #define ARM_PSCI_STACK_SIZE	(1 << ARM_PSCI_STACK_SHIFT)
 
+/* PSCI affinity level state returned by AFFINITY_INFO */
+#define PSCI_AFFINITY_LEVEL_ON		0
+#define PSCI_AFFINITY_LEVEL_OFF		1
+#define PSCI_AFFINITY_LEVEL_ON_PENDING	2
+
 #ifndef __ASSEMBLY__
 #include <asm/types.h>
 

arch/arm/include/asm/system.h

@@ -3,6 +3,7 @@
 
 #include <common.h>
 #include <linux/compiler.h>
+#include <asm/barriers.h>
 
 #ifdef CONFIG_ARM64
 
@@ -34,11 +35,6 @@ enum dcache_option {
 	DCACHE_WRITEALLOC = 4 << 2,
 };
 
-#define isb()				\
-	({asm volatile(			\
-	"isb" : : : "memory");		\
-	})
-
 #define wfi()				\
 	({asm volatile(			\
 	"wfi" : : : "memory");		\
@@ -227,8 +223,6 @@ void __noreturn psci_system_reset(bool smc);
  */
 void save_boot_params_ret(void);
 
-#define isb() __asm__ __volatile__ ("" : : : "memory")
-
 #define nop() __asm__ __volatile__("mov\tr0,r0\t@ nop\n\t");
 
 #ifdef __ARM_ARCH_7A__

arch/arm/lib/Makefile

@@ -26,8 +26,9 @@ endif
 
 obj-$(CONFIG_CPU_V7M) += cmd_boot.o
 obj-$(CONFIG_OF_LIBFDT) += bootm-fdt.o
+obj-$(CONFIG_CMD_BOOTI) += bootm.o
 obj-$(CONFIG_CMD_BOOTM) += bootm.o
-obj-$(CONFIG_CMD_BOOTM) += zimage.o
+obj-$(CONFIG_CMD_BOOTZ) += bootm.o zimage.o
 obj-$(CONFIG_SYS_L2_PL310) += cache-pl310.o
 obj-$(CONFIG_USE_ARCH_MEMSET) += memset.o
 obj-$(CONFIG_USE_ARCH_MEMCPY) += memcpy.o
@@ -67,11 +68,6 @@ extra-y	+= eabi_compat.o
 endif
 
 asflags-y += -DCONFIG_ARM_ASM_UNIFIED
-ifeq ($(CONFIG_SPL_BUILD)$(CONFIG_TEGRA),yy)
-asflags-y += -D__LINUX_ARM_ARCH__=4
-else
-asflags-y += -D__LINUX_ARM_ARCH__=$(CONFIG_SYS_ARM_ARCH)
-endif
 
 # some files can only build in ARM or THUMB2, not THUMB1
 

arch/arm/lib/bootm-fdt.c

@@ -25,6 +25,7 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
+#ifdef CONFIG_ARCH_FIXUP_FDT
 int arch_fixup_fdt(void *blob)
 {
 	bd_t *bd = gd->bd;
@@ -60,3 +61,4 @@ int arch_fixup_fdt(void *blob)
 
 	return 0;
 }
+#endif

arch/arm/lib/bootm.c

@@ -248,15 +248,20 @@ static void boot_prep_linux(bootm_headers_t *images)
 	}
 }
 
+__weak bool armv7_boot_nonsec_default(void)
+{
+#ifdef CONFIG_ARMV7_BOOT_SEC_DEFAULT
+	return false;
+#else
+	return true;
+#endif
+}
+
 #ifdef CONFIG_ARMV7_NONSEC
 bool armv7_boot_nonsec(void)
 {
 	char *s = getenv("bootm_boot_mode");
-#ifdef CONFIG_ARMV7_BOOT_SEC_DEFAULT
-	bool nonsec = false;
-#else
-	bool nonsec = true;
-#endif
+	bool nonsec = armv7_boot_nonsec_default();
 
 	if (s && !strcmp(s, "sec"))
 		nonsec = false;
@@ -367,8 +372,10 @@ void boot_prep_vxworks(bootm_headers_t *images)
 	if (images->ft_addr) {
 		off = fdt_path_offset(images->ft_addr, "/memory");
 		if (off < 0) {
+#ifdef CONFIG_ARCH_FIXUP_FDT
 			if (arch_fixup_fdt(images->ft_addr))
 				puts("## WARNING: fixup memory failed!\n");
+#endif
 		}
 	}
 #endif

arch/arm/lib/psci-dt.c

@@ -19,7 +19,6 @@ int fdt_psci(void *fdt)
 #if defined(CONFIG_ARMV8_PSCI) || defined(CONFIG_ARMV7_PSCI)
 	int nodeoff;
 	unsigned int psci_ver = 0;
-	char *psci_compt;
 	int tmp;
 
 	nodeoff = fdt_path_offset(fdt, "/cpus");
@@ -51,27 +50,10 @@ int fdt_psci(void *fdt)
 		fdt_setprop_string(fdt, tmp, "enable-method", "psci");
 	}
 
-	/*
-	 * The PSCI node might be called "/psci" or might be called something
-	 * else but contain either of the compatible strings
-	 * "arm,psci"/"arm,psci-0.2"
-	 */
 	nodeoff = fdt_path_offset(fdt, "/psci");
 	if (nodeoff >= 0)
 		goto init_psci_node;
 
-	nodeoff = fdt_node_offset_by_compatible(fdt, -1, "arm,psci");
-	if (nodeoff >= 0)
-		goto init_psci_node;
-
-	nodeoff = fdt_node_offset_by_compatible(fdt, -1, "arm,psci-0.2");
-	if (nodeoff >= 0)
-		goto init_psci_node;
-
-	nodeoff = fdt_node_offset_by_compatible(fdt, -1, "arm,psci-1.0");
-	if (nodeoff >= 0)
-		goto init_psci_node;
-
 	nodeoff = fdt_path_offset(fdt, "/");
 	if (nodeoff < 0)
 		return nodeoff;
@@ -83,41 +65,53 @@ int fdt_psci(void *fdt)
 init_psci_node:
 #ifdef CONFIG_ARMV8_SEC_FIRMWARE_SUPPORT
 	psci_ver = sec_firmware_support_psci_version();
+#elif defined(CONFIG_ARMV7_PSCI_1_0)
+	psci_ver = ARM_PSCI_VER_1_0;
 #endif
 	switch (psci_ver) {
-	case 0x00010000:
-		psci_compt = "arm,psci-1.0";
-		break;
-	case 0x00000002:
-		psci_compt = "arm,psci-0.2";
-		break;
+	case ARM_PSCI_VER_1_0:
+		tmp = fdt_setprop_string(fdt, nodeoff,
+				"compatible", "arm,psci-1.0");
+		if (tmp)
+			return tmp;
+	case ARM_PSCI_VER_0_2:
+		tmp = fdt_appendprop_string(fdt, nodeoff,
+				"compatible", "arm,psci-0.2");
+		if (tmp)
+			return tmp;
 	default:
-		psci_compt = "arm,psci";
+	/*
+	 * The Secure firmware framework isn't able to support PSCI version 0.1.
+	 */
+#ifndef CONFIG_ARMV8_SEC_FIRMWARE_SUPPORT
+		tmp = fdt_appendprop_string(fdt, nodeoff,
+				"compatible", "arm,psci");
+		if (tmp)
+			return tmp;
+		tmp = fdt_setprop_u32(fdt, nodeoff, "cpu_suspend",
+				ARM_PSCI_FN_CPU_SUSPEND);
+		if (tmp)
+			return tmp;
+		tmp = fdt_setprop_u32(fdt, nodeoff, "cpu_off",
+				ARM_PSCI_FN_CPU_OFF);
+		if (tmp)
+			return tmp;
+		tmp = fdt_setprop_u32(fdt, nodeoff, "cpu_on",
+				ARM_PSCI_FN_CPU_ON);
+		if (tmp)
+			return tmp;
+		tmp = fdt_setprop_u32(fdt, nodeoff, "migrate",
+				ARM_PSCI_FN_MIGRATE);
+		if (tmp)
+			return tmp;
+#endif
 		break;
 	}
 
-	tmp = fdt_setprop_string(fdt, nodeoff, "compatible", psci_compt);
-	if (tmp)
-		return tmp;
 	tmp = fdt_setprop_string(fdt, nodeoff, "method", "smc");
 	if (tmp)
 		return tmp;
 
-#ifdef CONFIG_ARMV7_PSCI
-	tmp = fdt_setprop_u32(fdt, nodeoff, "cpu_suspend",
-				ARM_PSCI_FN_CPU_SUSPEND);
-	if (tmp)
-		return tmp;
-	tmp = fdt_setprop_u32(fdt, nodeoff, "cpu_off", ARM_PSCI_FN_CPU_OFF);
-	if (tmp)
-		return tmp;
-	tmp = fdt_setprop_u32(fdt, nodeoff, "cpu_on", ARM_PSCI_FN_CPU_ON);
-	if (tmp)
-		return tmp;
-	tmp = fdt_setprop_u32(fdt, nodeoff, "migrate", ARM_PSCI_FN_MIGRATE);
-	if (tmp)
-		return tmp;
-#endif
 #endif
 	return 0;
 }