The logical expression to check the dtb is incorrect in
load_devicetree.
The problem was indicated by cppcheck.
The inconsistent variable name dtppart is changed to dtbpart.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Acked-by: Hannes Schmelzer <oe5hpm@oevsv.at>
The evaluation of option -c is incorrect:
According to the C99 standard endptr in the first strtol is always
set as &endptr is not NULL.
So the first part of the or condition is always true.
If all digits in optarg are valid endptr will point to the closing \0
and the second strtol will read beyond the end of the string optarg
points to.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
We should not first dereference p and afterwards assert that is
was not NULL. Instead do the assert first.
The problem was indicated by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
In dram_init_banksize there seems to be a typo concerning
a plausibility check of the fdt.
Testing sc > 2 twice does not make any sense.
The problem was indicated by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
A feature rich Linux kernel needs more than 8 MiB.
Hence enlarge CONFIG_SYS_BOOTM_LEN to 64 MiB for the GXBB systems.
As all known GXBB systems have at least 512 MiB of RAM this poses no problem.
Cc: Andreas Färber <afaerber@suse.de>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
.probe method has been assigned twice when declaring
a driver with U_BOOT_DRIVER(). Removed one of them.
Here is the last commit which had the duplicate entry:
"spi: omap3: Convert to driver model"
(sha1: 77b8d04854)
Signed-off-by: Suniel Mahesh <suniel.spartan@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This is not currently implemented. Add support for this so that the
Chrome OS EC can be used reliably.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Acked-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Before using the cs_gpio, check if the GPIO is valid or not.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Mention eMMC and microSD as supported devices.
They have been enabled with patch
d0c5c8d529
odroid-c2: enable new Meson GX MMC driver in board defconfig
which was accepted for u-boot-mmc.git.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
To enable automatic booting from SD card or eMMC the MMC
devices 0, 1, and 2 are added to the BOOT_TARGET_DEVICES.
Booting from SD card, eMMC, and DHCP are tried in sequence.
A missing or failing device is gracefully handled.
Cc: Andreas Färber <afaerber@suse.de>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Tested-by: Andreas Färber <afaerber@suse.de>
Add warp7_secure_defconfig entry to avoid the following warning:
WARNING: no maintainers for 'warp7_secure'
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
With 3f66149d9f we no longer have a common call fdt_fixup_ethernet.
This was fine to do on PowerPC as they largely had calls already in
ft_cpu_fixup. On ARM however we largely relied on this call. Rather
than introduce a large number of changes to ft_cpu_fixup /
ft_board_fixup we recognize that this is a common enough call that we
should be doing it in a central location. Do it early enough that we
can do any further updates in ft_cpu_fixup / ft_board_fixup.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Thomas Chou <thomas@wytron.com.tw> (maintainer:NIOS)
Cc: York Sun <york.sun@nxp.com> (maintainer:POWERPC MPC85XX)
Cc: Stefan Roese <sr@denx.de> (maintainer:POWERPC PPC4XX)
Cc: Simon Glass <sjg@chromium.org>
Cc: Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
Fixes: 3f66149d9f ("Remove extra fdt_fixup_ethernet() call")
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_CMD_DIAG
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: imply CMD_DIAG on some keymile configs]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CMD_DEKBLOB
Note: This option does not seem to actually be enabled by any board.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: imply under SECURE_BOOT for mx5/6/7]
Signed-off-by: Tom Rini <trini@konsulko.com>
Rather than using CMD_CRAMFS for both the filesystem and its command, we
should have a separate option for each. This allows us to enable CRAMFS
support without the command, if desired, which reduces U-Boot's size
slightly.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: imply FS_CRAMFS for keymile]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CMD_CRAMFS
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: imply CMD_CRAMFS for keymile]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CMD_CLK
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: imply CMD_CLK on ARCH_ZYNQ]
Signed-off-by: Tom Rini <trini@konsulko.com>
Rather than using CMD_CBFS for both the filesystem and its command, we
should have a separate option for each. This allows us to enable CBFS
support without the command, if desired, which reduces U-Boot's size
slightly.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: imply FS_CBFS on SYS_COREBOOT]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CMD_CBFS
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: imply CMD_CBFS on SYS_COREBOOT]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_WHITE_ON_BLACK
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Make this default y on various SoCs]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CMD_BMP
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add depends on LCD || DM_VIDEO || VIDEO]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CMD_BMODE
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Make this default y and depend on mx5/6/7]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CMD_BLOB
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add imply CMD_BLOB under CHAIN_OF_TRUST]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CMD_AES
CONFIG_AES
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add select AES to CMD_AES]
Signed-off-by: Tom Rini <trini@konsulko.com>
This is only used by one board and should not be a CONFIG option. Instead
it should use the driver model pmic framework. For now, just move the
setting into the only board that uses it.
Signed-off-by: Simon Glass <sjg@chromium.org>
A few boards had not been fully re-synced with CONFIG_ARCH_MX5 / CONFIG_MX51 /
CONFIG_MX53 being in Kconfig. Do so now.
Signed-off-by: Tom Rini <trini@konsulko.com>
In file ext4fs.c funtion ext4fs_read_file() compares an
unsigned expression with < 0 like below
lbaint_t blknr;
blknr = read_allocated_block(&(node->inode), i);
if (blknr < 0)
return -1;
blknr is of type ulong/uint64_t. read_allocated_block() returns
long int. So comparing blknr with < 0 will always be false. Instead
declare blknr as long int.
Similarly ext4/dev.c does a similar comparison. Drop the redundant
comparison.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update Keystone2 secure device configs under
"TI SYSTEM SECURITY". Without this buildman keeps complaining
about the status of these boards.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Andrew F. Davis <afd@ti.com>
On ARM v7M, the processor will return to ARM mode when executing
a blx instruction with bit 0 of the address == 0. Always set it
to 1 to stay in thumb mode.
Tested on STM32f746-disco board
Similar commit:
f99993c108
Author: Matt Porter <mporter@konsulko.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
In Linux, CONFIG_ARCH_OMAP2PLUS is used for OMAP2 or later SoCs.
Rename CONFIG_ARCH_OMAP2 to CONFIG_ARCH_OMAP2PLUS to follow this
naming.
Move the OMAP2+ board/SoC choice down to mach-omap2/Kconfig to slim
down the arch/arm/Kconfig level.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
CONFIG_CMD_FS_UUID was neither whitelisted, nor was it declared in
Kconfig.
Now it can be enabled in .config and defconfig as expected.
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
Almost all TI defconfigs enable this already, add this as a default
and remove the explicit assignment.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Finally adding support for ARC boards in TravisCI.
To build for ARC boards we need to install Synopsys prebuilt toolchain
which we do here.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
As per the DM[1] Dated June 2016–Revised February 2017, Table 5-3,
DRA71 supports the following OPPs for various voltage domains:
VDD_MPU: OPP_NOM
VDD_CORE: OPP_NOM
VDD_GPU: OPP_NOM
VDD_DSPEVE: OPP_NOM, OPP_HIGH
VDD_IVA: OPP_NOM, OPP_HIGH
This patch add support for selection of the above OPPs instead of
using OPP_NOM for all voltage domains.
[1] http://www.ti.com/lit/ds/symlink/dra718.pdf
Reported-by: Vishal Mahaveer <vishalm@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
This originally started out as
"pinctrl: Kconfig: reorder to keep Rockchip options together"
and tried to keep the Rockchip-related config options together.
However, we now rewrite all chip-specific driver selections to start
with CONFIG_PINCTRL_ (with the inadvertent changes to related
Makefiles) and sort those alphabetically. And as this already means
touching most of the file, we also reformat the help text to not exceed
80 characters (but make full use of those 80 characters).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
An assignment (of a value to itself) was left over (after removing and
addition from the line) from moving the common padding code into
rkcommon_vrec_header.
This change removes this to avoid a spurious warning in static code
analysis (i.e. Coverity).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reported-by: Coverity (CID: 161418)
Reviewed-by: Tom Rini <trini@konsulko.com>
There are more and more cases where if we do not use gcc-6.0 or later we
run into problems where our binaries are too large for the targets.
Given the prevalence of gcc-6.0 or later toolchains at this point in
time, we give notice now that starting with v2018.01 we will require
gcc-6 (or later) for ARM.
Signed-off-by: Tom Rini <trini@konsulko.com>
Unfortunately a test for the PWM uclass was not included when it was
submitted. This was noticed when trying to add more functionality:
http://patchwork.ozlabs.org/patch/748172/
Add a simple test to get us started.
Signed-off-by: Simon Glass <sjg@chromium.org>
Standardise U-Boot prompt on all keystone2 platforms
instead of platform specific prompt.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The name of the gpio bank under DM_GPIO appear to be a copy-paste error.
This changes the name of the gpio bank from am33xx_gpios to omap34xx_gpios.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The register names and offset were not correct as per the TRM for OMAP3530
and OMAP3630. Correct the naing and offsets per the documentation
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Remove option which depends on MMC controller which is disabled for dc2.
Savedefconfig is removing it because of new dependencies.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Fixes the following problem:
zynq-uboot> run dfu_ram
Setting bus to 1
g_dnl_register: failed!, error: -19
The cause appears to be that the USB framework is looking for a usbotg aliases,
so add the alias to point to our USB device.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
We used to have opencoded ehci_readl()/writel() which required no
external functions to be called.
Now with attempt to switch to generic readl()/writel() accessors
we see a missing declaration of those accessors in ehci-ppc4xx.
Something like that happens if applied
http://patchwork.ozlabs.org/patch/726714/:
---------------->8---------------
CC drivers/usb/host/ehci-ppc4xx.o
drivers/usb/host/ehci-ppc4xx.c: In function 'ehci_hcd_init':
drivers/usb/host/ehci-ppc4xx.c:23:3: warning: implicit declaration of function 'readl' [-Wimplicit-function-declaration]
HC_LENGTH(ehci_readl(&(*hccr)->cr_capbase)));
^
---------------->8---------------
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
For id = 15 an out of bound access occurs in udc_setup_ep().
Increase the size of epinfo[] from 30 to 32 to encompass
ids 0..15.
The problem was highlighted by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
We want to check the result of musb_init_controller
and not the address were the result is stored.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add support for the Terasic DE10-Nano board. The board
is based on the DE0-Nano-Soc board but adds a larger FPGA
and an HDMI output.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Reviewed-by: Dinh Nguyen <dinguyen@kernel.org>
Only A23/A33 in SUN8I want a default value of CONS_INDEX of 5, for other
chips the default value is 1 like other Allwinner SoCs.
Fix this default value.
The original wrong value has lead to wrong console on H3 Orange Pi
boards.
Fixes: 7095f86418 ("sunxi: Convert CONS_INDEX to Kconfig")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Commit 088454cd dropped return value from initram(), setting
gd->ram_size directly. Three boards were missed for SPL boot.
Signed-off-by: York Sun <york.sun@nxp.com>
PSCI can be used on both multiple and single core socs. Current
implementation only allows PSCI to work on multiple core socs.
This patch removes this restriction so that PSCI can work on
single core socs as well.
Signed-off-by: Chenhui Zhao <chenhui.zhao@nxp.com>
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The PPA is a EL3 firmware, which support PSCI, hotplug,
power-management features etc.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The PPA is a EL3 firmware, which support PSCI, hotplug,
power-management features etc.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Since commit ce412b7, RGMII TX clock internal delay is not enabled
for AR8033 unconditionally. On LS1021ATWR board, the third port
eTSEC3 uses AR8033 in RGMII mode. The TX/RX internal delay needs to
be enabled.
This patch will set PHY_INTERFACE_MODE_RGMII_ID to enable RGMII TX/RX
clock internal delay for AR8033 on the third port.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Currently $fdtfile is constructed from CONFIG_DEFAULT_TREE, containing
the filename. However on arm64 that file is located in an allwinner
subdirectory.
To avoid the need for users/distros symlinking the .dtb files, prepend
the vendor directory for ARM64.
This aligns Pine64 with other boards such as Raspberry Pi 3.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Before this patch, CONFIG_SYS_BOOTPARAMS_LEN was the same size as
CONFIG_SYS_MALLOC_LEN. So, if malloc() had previously been called, and
initr_malloc_bootparams() was called, it would fail with an out-of-
memory error. This patch fixes this issue by expanding the malloc pool
to 256KB.
Signed-off-by: Kyle Edwards <kyleedwardsny@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This fixes an issue with the saveenv command causing U-Boot to no
longer work on the QEMU Mips pseudoboard. Because the offset of the
environment was being determined by CONFIG_SYS_MONITOR_LEN, and this
value was less than the actual size of U-Boot, saveenv was overwriting
parts of the U-Boot code. Because CONFIG_SYS_MONITOR_LEN is no longer
used on MIPS, this patch removes it and places the environment at the
end of the pseudoboard's 4MB flash.
Signed-off-by: Kyle Edwards <kyleedwardsny@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Lichee Pi Zero is a development board with a V3s SoC, which features
64MiB DRAM co-packaged within the SoC, a TF slot, a SPI NOR slot (not
soldered in production batch), a 40-pin RGB LCD connector and some extra
pins available as 2.54mm pins or stamp holes.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Basic U-Boot support is now present for V3s.
Some memory addresses are changed specially for V3s, as the original
address map cannot fit into a so small DRAM.
As the DRAM controller code needs a big refactor, the SPL support is
disabled in this version.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
- Use - instead of @ for OPP tables
- Add input-delay properties to Cadence eMMC nodes
- Restore full license text because code-diff is annoying
- Fix NAND compatible strings
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The SCP (System Control Processor) or what we call STM (Stand-by
MPU) is integrated in LD4, Pro4, sLD8, LD6b, LD11, and LD20.
For these SoCs, show the information if STM is enabled.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This configuration is supposed to be used with ARM Trusted Firmware,
so the SYSTEM_RESET is implemented in BL31. Invoke PSCI instead of
U-Boot's own reset code because we need to coordinate with SCP
(System Control Processor) for the system-level power management.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Video driver for older Allwinner SoCs uses cfb console framework which
in turn uses struct ctfb_res_modes to hold timing informations. However,
DM video framework uses different structure - struct display_timing.
It makes more sense to convert lcdc to use new timing structure because
all new drivers should use DM video framework and older drivers might be
rewritten to use new framework too.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Bananapi M2 Ultra is the first publicly available development board
featuring the R40 SoC.
This patch add barebone dtsi/dts files for the R40 and Bananapi M2 Ultra,
as well as a defconfig for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The R40's CPU controls are a combination of sun6i and sun7i.
All controls are in the CPUCFG block, and it seems the R40 does not
have a PRCM block. The core reset, power gating and clamp controls
are grouped like sun6i.
Last, the R40 does not have a secure SRAM block.
This patch adds a PSCI implementation for CPU bring-up and hotplug
for the R40.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we can do DRAM initialization for the R40, we can enable
SPL support for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The R40 seems to have a variant of the memory controller found in
the H3 and A64 SoCs. Adapt the code for use on the R40. The changes
are based on released DRAM code and comparing register dumps from
boot0.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The PIO on the R40 SoC is mostly compatible with the A20.
Only a few pin functions for mmc2 were added to the PC
pingroup, to support 8 bit eMMCs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
These values were taken from the Banana Pi M2 Ultra fex file
found in the released vendor BSP. This is the only publicly
available R40 device at the time of this writing.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
According to the BSP released by Banana Pi, the R40 (sun8iw11p1) has
an extra "PLL lock control" register in the CCU, which controls whether
the individual PLL lock status bits in each PLL's control register work
or not.
This patch enables it for all the PLLs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The PIO is generally compatible with the A20, except that it routes the
full 8 bits and eMMC reset pins for mmc2.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The watchdog found on the R40 SoC is the older variant found on the A20.
Add the proper "#if defines" to make it work.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The R40 SoC uses the AXP221s in I2C mode to supply power.
Some regulator's common usages have changed, and also the recommended
voltage for existing usages have changed. Update the defaults to match.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The R40 is the successor to the A20. It is a hybrid of the A20, A33
and the H3.
The R40's PIO controller is compatible with the A20,
Reuse the A20 UART and I2C muxing code by adding the R40's macro.
The display pipeline is the newer DE 2.0 variant.
Block enabling video on R40 for now.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Currently we have some lines in board/sunxi/Kconfig that are very long.
These line either provide default values for a set of SoCs, or limit
some option to a subset of sunxi SoCs.
Fortunately Kconfig makes it easy to split them. The Kconfig language
document states
If multiple dependencies are defined, they are connected with '&&'.
This means we can split existing dependencies at "&&" symbols. This
applies to both the "depends on" lines and "if" expressions.
This patch splits them up to one symbol per line. This will make it
easier to add, remove, or modify one item at a time.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Convert the CONS_INDEX configuration to Kconfig.
Update sunxi's defconfigs to remove SYS_EXTRA_OPTIONS variable not
needed anymore.
Default value is 1 except for sun5i (equals 2) and sun8i (equals 5).
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
[Maxime: Added a depends on ARCH_SUNXI to avoid build breakages]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Convert CONFIG_RGMII to Kconfig. Thanks to that, it is possible to
update defconfig files of SYS_EXTRA_OPTIONS accordingly and
remove it when it is possible.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Convert the SUNXI_EMAC config to Kconfig. Remove it from SYS_EXTRA_OPTIONS
from many sunxi defconfig and renamed it into SUN4I_EMAC to not confuse it
with SUN8I_EMAC.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The USB_EHCI configuration is already set in this defconfig
using kconfig's config. This configuration in SYS_EXTRA_OPTIONS
must be removed and so the SYS_EXTRA_OPTIONS.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Remove the AXP209_POWER option from SYS_EXTRA_OPTIONS.
As this configuration already exists on Kconfig, we just need
to remove it from defconfig.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
At present if the return to bootrom fails (e.g. because you are not using
the Rockchip's bootrom's pointer table in MMC) then the board prints
SPL message and hangs. Print a message first if we can, to help in
understanding what happened when it hangs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Heiko Stuebner <heiko@sntech.de>
'A || (!A && B)' is equivalent to 'A || B'.
Let's reduce the complexity of the statement in start_jr0().
The problem was indicated by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
After allocating sata->cmd_hdr_tbl_offset we have to check
this variable and not variable sata.
The problem was indicated by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
(pdimm[0].data_width >= 32) || (pdimm[0].data_width <= 40)
is always true.
We should use && here.
The problem was indicated by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The number of arguments for printf does not match the
format string.
The problem was indicated by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
If current_urb is NULL it should not be dereferenced.
The problem was indicated by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
If !parent, the changed line is not reached.
So there is no need to check the value again.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Each call of va_start must be matched by a call of va_end.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Linaro provides a number of pre-built GCC toolchains for both 32 and
64bit ARM. Switch to their 2017.02 release of gcc-6.3.1 for both.
Cc: Koen Kooi <koen.kooi@linaro.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Many toolchains for ARM use the 'gnueabihf' suffix rather than just
'gnueabi', so allow these to be used, but with a lower priority than
'gnueabi' ones.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If the system is running PSCI firmware, the System Reset function
(func ID: 0x80000009) is supposed to be handled by PSCI, that is,
the SoC/board specific reset implementation should be moved to PSCI.
U-Boot should call the PSCI service according to the arm-smccc
manner.
The arm-smccc is supported on ARMv7 or later. Especially, ARMv8
generation SoCs are likely to run ARM Trusted Firmware BL31. In
this case, U-Boot is a non-secure world boot loader, so it should
not be able to reset the system directly.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Imports ARM SMC Calling Convention code from Linux 4.11-rc6.
The files have been copied as follows:
[Linux] [U-Boot]
arch/arm/kernel/smccc-call.S -> arch/arm/cpu/armv7/smccc-call.S
arch/arm64/kernel/smccc-call.S -> arch/arm/cpu/armv8/smccc-call.S
arch/arm/include/asm/opcodes* -> arch/arm/include/asm/opcodes*
include/linux/arm-smccc.h -> include/linux/arm-smccc.h
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Handle symlinks to files in the current directory. Other cases could be
handled with additional code, but this is a start.
Add explicit errors for absolute paths and links found in the middle of
a path (directories). Other cases like '..' or '.' will result with the
file not being found as when those path components are explicitly
provided.
Add a helper to decompress a null-terminated link name which is shared
with cramfs_list_inode.
Signed-off-by: Tyler Hall <tylerwhall@gmail.com>
Using a variably-sized type is incorrect here since we're reading a
fixed file format. Fixes cramfs on 64-bit platforms.
Signed-off-by: Tyler Hall <tylerwhall@gmail.com>
As with most other commands, this needs to factor in the sysmem offset
in the sandbox or it will try to dereference the simulated physical
address directly.
Signed-off-by: Tyler Hall <tylerwhall@gmail.com>
Enable this command so we can get an approximate performance measurement.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present on a cold reboot we must reset the CPU to get it to full speed.
With 64-bit U-Boot this happens in SPL. At present we print the banner
before doing this, the end result being that we print the banner twice.
Print the banner a little later (after the CPU is ready) to avoid this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
The Intel CPU name can have leading spaces. Remove them since they are not
useful.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
A size_t variable can never be negative.
The problem was indicated by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
As board-specific reset logic, it needs to issue reset signal
via CPLD when issuing 'reset' command in u-boot, this patch
solves the issue of reset command not working on T1024RDB.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
For E6500 cores, L2 cache has been used as init_ram. L1 cache is a
write through cache on E6500.If lines are not locked in both L1 and
L2 caches, crashes are observed during secure boot. This patch locks/
unlocks both L1 and L2 cache to prevent the crash.
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Current sysclk fixing would fix all clocks with 'fixed-clock' compatible.
This patch is to fix sysclk by path to avoid any incorrect fixing.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Number of TZASC instances may vary across NXP SoCs.
So put TZASC configuration under instance specific defines.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
- Add SD secure boot target for ls1046ardb.
- Change the u-boot size defined by a macro for copying the main
U-Boot by SPL to also include the u-boot Secure Boot header size
as header is appended to u-boot image. So header will also be
copied from SD to DDR.
- CONFIG_MAX_SPL_SIZE is limited to 90KB. SPL is copied to OCRAM
(128K) where 32K are reserved for use by boot ROM and 6K for the
header.
- Reduce the size of CAAM driver for SPL Blobification functions
and descriptors, that are not required at the time of SPL are
disabled. Further error code conversion to strings is disabled
for SPL build.
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add NAND secure boot target for ls1043ardb.
- Change the u-boot size defined by a macro for copying the main
U-Boot by SPL to also include the u-boot Secure Boot header size as
header is appended to u-boot image. So header will also be copied
from SD to DDR.
- MACRO for CONFIG_BOOTSCRIPT_COPY_RAM is enabled to copy Bootscript
from NAND to DDR. Offsets for Bootscript on NAND and DDR have been
also defined.
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
- Add SD secure boot target for ls1043ardb.
- Implement FSL_LSCH2 specific spl_board_init() to setup CAAM stream
ID and corresponding stream ID in SMMU.
- Change the u-boot size defined by a macro for copying the main
U-Boot by SPL to also include the u-boot Secure Boot header size as
header is appended to u-boot image. So header will also be copied
from SD to DDR.
- CONFIG_MAX_SPL_SIZE is limited to 90KB. SPL is copied to OCRAM
(128K) where 32K are reserved for use by boot ROM and 6K for secure
boto header.
- Error messages during SPL boot are limited to error code numbers
instead of strings to reduce the size of SPL image.
Signed-off-by: Vinitha Pillai-B57223 <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Define bootscript and its header addresses for QSPI target
Also add PPA header address in Kconfig
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Using changes in this patch we were able to reduce approx 4k
size of u-boot-spl.bin image. Following is breif description of
changes to reduce SPL size:
1. Changes in board/freescale/ls1046ardb/Makefile to remove
compilation of eth.c and cpld.c in case of SPL build.
2. Changes in board/freescale/ls1046ardb/ls1046ardb.c to keep
only ddr_init and board_early_init_f funcations in case of SPL
build.
3. Changes in ls1046a_common.h & ls1046ardb.h to remove driver
specific macros due to which static data was being compiled in
case of SPL build.
4. Disable MMC driver from bieng compiled in case of SPL NAND
build and NAND driver from bieng compiled in case of SPL MMC build.
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Using changes in this patch we were able to reduce approx 10k
size of u-boot-spl.bin image. Following is breif description of
changes to reduce SPL size:
1. Changes in board/freescale/ls1043ardb/Makefile to remove
compilation of eth.c and cpld.c in case of SPL build.
2. Changes in board/freescale/ls1043ardb/ls1043ardb.c to keep
only ddr_init and board_early_init_f funcations in case of SPL
build.
3. Changes in ls1043a_common.h & ls1043ardb.h to remove driver
specific macros due to which static data was being compiled in
case of SPL build.
4. Disable MMC driver from bieng compiled in case of SPL NAND
build and NAND driver from bieng compiled in case of SPL MMC build.
5. Remove I2C driver support from SPL in case of LS1043ARDB.
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Depending on DDR configuration, gcc-6.x will show up unused-const-
variable messages. Use __maybe_unused specifier for all dynamic_odt
variable definitions to remove these warnings.
Memory footprint will not increase as gcc will optimize out unused
constants.
Signed-off-by: Thomas Schaefer <thomas.schaefer@kontron.com>
Signed-off-by: York Sun <york.sun@nxp.com>
The RK3399-Q7 ("Puma") SoM exposes UART0 as the Qseven UART (i.e. the
serial line available via standardised pins on the edge connector and
available on a RS232 connector).
To support boards (such as the RK3399-Q7) that require UART0 as a
debug console, we match CONFIG_DEBUG_UART_BASE and add the appropriate
iomux setup to the rk3399 SPL code.
As we are already touching this code, we also move the board-specific
UART setup (i.e. iomux setup) into board_debug_uart_init(). This will
be called from the debug UART init when CONFIG_DEBUG_UART_BOARD_INIT
is set.
As the RK3399 needs to use its board_debug_uart_init() function, we
have Kconfig enable it by default for RK3399 builds.
With everything set up to define CONFIG_BAUDRATE via defconfig and
with to have the SPL debug UART either on UART0 or UART2, the configs
for the RK3399 EVB are then update (the change for the RK3399-Q7 is
left for later to not cause issues on applying the change).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
For using mipi display, we need to enable lcd3v3
which supplied by rk808,so enable rk808 first.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
To enable mipi display, we need to enable pmic
rk808 first for lcd3v3 power,which use i2c0 to
communicate with soc. So enable i2c0.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
when enable PMIC rk808,the system will halt at very
early stage,log is shown as bellow.
INFO: plat_rockchip_pmu_init(1211): pd status 3e
INFO: BL31: Initializing runtime services
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0x200000
INFO: SPSR = 0x3c9
time 44561b, 0 (<<----Just stop here)
It's caused by the absence of "{ }" in syscon_rk3399.c
,which will lead to memory overflow like below.According
to Sysmap file ,we can find the function buck_get_value
of rk808 is just follow the compatible struct,the pointer
"of_match" point to "buck_get_value",but it is not a
struct and don't have member of compatible, In this case,
system crash. So,on the face, it looks like that rk808 is
guilty.but he is really innocent.
while (of_match->compatible) { <<----------
if (!strcmp(of_match->compatible, compat)) {
*of_idp = of_match;
return 0;
}
of_match++;
}
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
The RK3399-Q7 SoM is a Qseven-compatible (70mm x 70mm, MXM-230
connector) system-on-module from Theobroma Systems, featuring the
Rockchip RK3399.
It provides the following feature set:
* up to 4GB DDR3
* on-module SPI-NOR flash
* on-module eMMC (with 8-bit interace)
* SD card (on a baseboad) via edge connector
* Gigabit Ethernet w/ on-module Micrel KSZ9031 GbE PHY
* HDMI/eDP/MIPI displays
* 2x MIPI-CSI
* USB
- 1x USB 3.0 dual-role (direct connection)
- 2x USB 3.0 host + 1x USB 2.0 (on-module USB 3.0 hub)
* on-module STM32 Cortex-M0 companion controller, implementing:
- low-power RTC functionality (ISL1208 emulation)
- fan controller (AMC6821 emulation)
- USB<->CAN bridge controller
Note that we use a multi-payload FIT image for booting and have
Cortex-M0 payload in a separate subimage: we thus rely on the FIT
image loader to put it into the SRAM region that ATF expects it in.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Fixed build warning on puma-rk3399:
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The RK3399-Q7 (Puma) DTS should (of course) be dual-licensed.
This updates the licensing info in the rk3399-puma.dts.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The warm-reset of rk3188 socs keeps the remap setting as it was, so if
it was enabled, the cpu would start from address 0x0 of the sram instead
of address 0x0 of the bootrom, thus making the reset hang.
Therefore make sure the remap is disabled before attempting a warm reset.
Cold reset is not affected by this at all.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
Most Rockchip socs have the ability to either map the bootrom or a sram
area to the starting address of the cpu by flipping a bit in the GRF.
Newer socs leave this untouched and mapped to the bootrom but the legacy
loaders on rk3188 and before enabled the remap functionality and the
current smp implementation in the Linux kernel also requires it to be
enabled, to bring up secondary cpus.
So to keep smp working in the kernel, mimic the behaviour of the legacy
bootloaders and enable the remap functionality.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
Somehow 43b5c78d8d ("rockchip: cosmetic: Sort RK3288 boards") moved
the rock board in between some rk3288 board, probably as a result of
rebasing.
So move it back to its original position above all rk3288 boards.
Fixes: 43b5c78d8d ("rockchip: cosmetic: Sort RK3288 boards")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
Now that most rockchip SoC based board have usb host support, enable
USB boot targets by default.
Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Fixed build errors when CONFIG_CMD_USB not defined:
Signed-off-by: Simon Glass <sjg@chromium.org>
tinker board support ethernet and usb host, so enable USB, PXE and DHCP support.
Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The RK3399 hangs during DMA of the Designware MMC controller, when
performing DMA-based transactions in SPL due to the DDR security settings
left behind by the BootROM (i.e. accesses to the first MB of DRAM are
restricted... however, the DMA is likely to target this first MB, as it
transfers from/to the stack).
System security is not affected, as the final security configuration is
performed by the ATF, which is executed after the SPL stage.
With this fix in place, we can now drop 'fifo-mode' in the DTS for the
RK3399-Q7 (Puma).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Enable the early debug UART to debug problems when an ICE or other
debug mechanism is not available.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Due to the introduction of the pinctrl and clk driver, and using
device tree files, remove the unneeded hardcoded pin configuration
and clock enabling code from the board file.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Update the configuration files to support the device tree and driver
model, so do SPL. The device clock and pins configuration are handled
by the clock and the pinctrl drivers respectively.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Fix build error with sama5d3_xplained_mmc:
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable the early debug UART to debug problems when an ICE or other
debug mechanism is not available.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Due to the introduction of the pinctrl and clk driver, and using
device tree files, remove the unneeded hardcoded pin configuration
and clock enabling code from the board file.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Remove CONFIG_PHY_MICREL as per previous patch:
Signed-off-by: Simon Glass <sjg@chromium.org>
Update the configuration files to support the device tree and
driver model, so do SPL. The device clock and pins configuration
are handled by the clock and the pinctrl drivers respectively.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Add back CONFIG_PHY_MICREL to prevent a build error:
Signed-off-by: Simon Glass <sjg@chromium.org>
When driver model is used for LEDs, provide a command to allow LED access.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ziping Chen <techping.chan@gmail.com>
The existing 'led' command does not support driver model. Rename it to
indicate that it is legacy code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ziping Chen <techping.chan@gmail.com>
Allow LEDs to be blinked if the driver supports it. Enable this for
sandbox so that the tests run.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ziping Chen <techping.chan@gmail.com>
Add support for toggling an LED into the uclass interface. This can be
efficiently implemented by the driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ziping Chen <techping.chan@gmail.com>
It is useful to be able to read the LED as well as write it. Add this to
the uclass and update the GPIO driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ziping Chen <techping.chan@gmail.com>
At present this is very simple, supporting only on and off. We want to
also support toggling and blinking. As a first step, change the name of
the main method and use an enum to indicate the state.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ziping Chen <techping.chan@gmail.com>
These structures are normally named with 'uc' instead of 'uclass'. Change
this one for consistency.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ziping Chen <techping.chan@gmail.com>
There should be a blank line between each option. Add one before LED_GPIO.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ziping Chen <techping.chan@gmail.com>
With DM_SCSI enabled, blk_create_devicef() is called with blkz = 0, leading
to a divide-by-0 exception.
scsi_detect_dev() can be used to get the required parameters (block size
and number of blocks) from the drive before calling blk_create_devicef().
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We might want to get information about the scsi device without initializing the partition.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This is a cosmetic change. target and LUN have kind of the same role in
this function. One of them was passed as a parameter and the other was
embedded in a structure. For consistency, pass both of them as parameters.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When CONFIG_DM_SCSI is defined, the SATA initialization will be implemented
in the scsi-uclass driver.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
All the clocks which has to be enabled has to be done in
enable_basic_clocks(), so moving enable sata clock to common
clocks enable function.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
When writing out some of our results we may now have UTF-8 characters
in there as well. Translate these to latin-1 and ignore any errors (as
this is for diagnostic and given the githash anything else can be
reconstructed by the user.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This fixes a regression caused by
commit 07b2b78ce4
dm: usb: Convert USB storage to use driver-model for block devs
which caused part_init to be called when it was not previously.
Without this patch, the following happens when a USB sd card reader is used.
=> usb start
starting USB...
USB0: Port not available.
USB1: USB EHCI 1.00
scanning bus 1 for devices... 3 USB Device(s) found
scanning usb for storage devices... Device NOT ready
Request Sense returned 02 3A 00
### ERROR ### Please RESET the board ###
This happens because dev_desc->blksz is 0.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
We should invalidate the dcache before starting the DMA. In case there are
any dirty lines from the DMA buffer in the cache, subsequent cache-line
replacements may corrupt the buffer in memory while the DMA is still going on.
Cache-line replacement can happen if the CPU tries to bring some other memory
locations into the cache while the DMA is going on.
Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Reviewed-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Merely using dma_alloc_coherent does not ensure that there is no stale
data left in the caches for the allocated DMA buffer (i.e. that the
affected cacheline may still be dirty).
The original code was doing the following (on AArch64, which
translates a 'flush' into a 'clean + invalidate'):
# during initialisation:
1. allocate buffers via memalign
=> buffers may still be modified (cached, dirty)
# during interrupt processing
2. clean + invalidate buffers
=> may commit stale data from a modified cacheline
3. read from buffers
This could lead to garbage info being written to buffers before
reading them during even-processing.
To make the event processing more robust, we use the following sequence
for the cache-maintenance:
# during initialisation:
1. allocate buffers via memalign
2. clean + invalidate buffers
(we only need the 'invalidate' part, but dwc3_flush_cache()
always performs a 'clean + invalidate')
# during interrupt processing
3. read the buffers
(we know these lines are not cached, due to the previous
invalidation and no other code touching them in-between)
4. clean + invalidate buffers
=> writes back any modification we may have made during event
processing and ensures that the lines are not in the cache
the next time we enter interrupt processing
Note that with the original sequence, we observe reproducible
(depending on the cache state: i.e. running dhcp/usb start before will
upset caches to get us around this) issues in the event processing (a
fatal synchronous abort in dwc3_gadget_uboot_handle_interrupt on the
first time interrupt handling is invoked) when running USB mass
storage emulation on our RK3399-Q7 with data-caches on.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The dwc3_flush_cache() call was declared and used inconsistently:
* The declaration assumed 'int' for addresses (a potential issue
when running in a LP64 memory model).
* The invocation cast the address to 'long'.
This change ensures that both the declaration and usage of this
function consistently uses 'uintptr_t' for correct behaviour even
when the allocated buffers (to be flushed) reside outside of the
lower 32bits of memory.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Both these numbers are calculated in runtime and dynamically assigned
to the device descriptor during bind().
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We don't want to claim that we support a serial number string and
later return nothing. Because of that, if g_dnl_serial is an empty
string, let's skip setting iSerialNumber to a valid number.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
A USB String descriptor can be up to 255 characters long and it's not
NULL terminated according to the USB spec. This means our
MAX_STRING_SERIAL should be 256 (to cope with NULL terminator).
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
After enabling log printing to lcd, when the screen starts
scrolling, system crashes. Log is shown as bellow:
"Synchronous Abort" handler, esr 0x96000045
"Synchronous Abort" handler, esr 0x96000045
Checking the source code, we found that the variable "pixels"
gets a wrong value:
int pixels = VIDEO_FONT_HEIGHT * vid_priv->line_length;
"pixels" here means the value of pixels for a character, rather
than the bytes for a character. So the variable "pixels" is 4
times bigger than it's exact value, which will cause the memory
overflow when the cpu runs the following code:
for (i = 0; i < pixels; i++)
*dst++ = clr; <<----
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Some board do not use the dwc2 internal VBUS_DRV signal, but
use a gpio pin to enable the 5.0V VBUS power, add interface to
enable the power in dwc2 driver.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
This removes the default environment from the sr1500 header
and instead uses the common environment provided in
socfpga_common.h which now uses distro boot.
This board has no upstream devicetree in the kernel source,
so set to socfpga_cyclone5_sr1500.dtb.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
--
Changes in v2:
- Remove unneeded CONFIG_BOOTFILE
- set devicetree name to match socfpga_{fpga model}_{board model}.dts
pattern
This removes the default environment from the socrates headers
and instead uses the common environment provided in
socfpga_common.h which now uses distro boot.
Change default devicetree name to match devicetree name in
upstream kernel source.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
--
Changes in v2:
- Remove unneeded CONFIG_BOOTFILE
This removes the default environment from the SoCKit headers
and instead uses the common environment provided in
socfpga_common.h which now uses distro boot.
Change default devicetree name to match devicetree name in
upstream kernel source.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
--
Changes in v2:
- Remove unneeded CONFIG_BOOTFILE
This removes the default environment from the de1 headers
and instead uses the common environment provided in
socfpga_common.h which now uses distro boot.
This board does not have a devicetree in the upstream kernel
source so set devicetree to socfpga_cyclone5_de1_soc.dtb.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
--
Changes in V2:
- Remove unneeded CONFIG_BOOTFILE
- set devicetree name to match socfpga_{fpga model}_{board model}.dts
pattern
This removes the default environment from the C5 SoCDK headers
and instead uses the common environment provided in
socfpga_common.h which now uses distro boot.
In addition to the above, add support to boot from the custom
a2 type partition.
Change default devicetree name to match devicetree name in
upstream kernel source.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
--
Changes in v2:
- Remove unneeded CONFIG_BOOTFILE
This removes the default environment from the A5 socdk headers
and instead uses the common environment provided in
socfpga_common.h which now uses distro boot.
Add support to boot from the custom a2 type partition.
Change default devicetree name to match devicetree name in
upstream kernel source.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
--
Changes in v3:
- Fix small typo in defconfig, missing "C"
Changes in v2:
- Remove unneeded CONFIG_BOOTFILE
- Fix dtb name
a5config test
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
This removes the default environment from the de0 headers
and instead uses the common environment provided in
socfpga_common.h which now uses distro boot.
In addition to the above, add support to boot from the custom
a2 type partition
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
--
Changes in v2:
- Remove unneeded CONFIG_BOOTFILE
This adds a common environment and support for distro boot
in the common socfpga header.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
--
Changes in v5:
- Per Frank, to support OpenSuse the ENV must be after the GPT
Changes in v4:
- Move env back to being right after the MBR
Changes in v3:
- fix spacing between asterix
- remove verify=n as a default setting
Changes in v2:
- Remove unneeded CONFIG_BOOTFILE and fdt_addr
- cleanup spacing in MMC env size
common
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Convert Altera DDR SDRAM driver to use Kconfig method.
Enable ALTERA_SDRAM by default if it is on Gen5 target.
Arria 10 will have different driver.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Disable the OC test on MCVEVK as the old PHY version does not provide
this information. This fixes the USB OTG operation.
Signed-off-by: Marek Vasut <marex@denx.de>
There is no point in having such gargantuan buffer, it only requires
huge malloc area. Reduce the DFU buffer size.
Signed-off-by: Marek Vasut <marex@denx.de>
Commit ce62e57fc5 ("ARM: boot0 hook: remove macro, include whole
header file") miss out cleaning macro in this header file, and this
has broken implementation of a boot header capability in socfpga
SPL. Remove the macro in this file, and recovering it back
to proper functioning.
Fixes: ce62e57fc5 ("ARM: boot0 hook: remove macro, include whole
header file")
Signed-off-by: Chee, Tien Fong <tien.fong.chee@intel.com>
With the port C enabled, we can read the GPI input state of:
* the DIP switches (USER_DIPSW_HPS[3:0]/HPS_GPI[7:4])
* the push buttons (USER_PB_HPS[3:0]/HPS_GPI[11:8])
Signed-off-by: Georges Savoundararadj <savoundg@gmail.com>
Signed-off by: Sid-Ali Teir <git.syedelec@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Marek Vasut <marex@denx.de>
This patch adds the steps to manually (re)build a Quartus FPGA project,
generate the required BSP glue, and update u-boot handoff files for
mainline SPL support. Requires Quartus toolchain and current U-Boot.
Signed-off-by: Steve Arnold <stephen.arnold42@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
The Vybrid SoC family has the same display controller unit (DCU)
like the LS1021A SoC. This patch adds platform data, pinmux defines
and clock control to enable the driver for Toradex Colibri Vybrid
module.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
DCU_LAYER_MAX_NUM is currently used for DCU_MODE_BLEND_ITER and it
actually overflows the maximum value of BLEND_ITER for Vybrid and
LS102XA. Fix this by using a default value of 2.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
When enabling the DCU and pixel clock, the test mode is activated
since this is the reset configuration. The test mode immediately
shows a red screen on a LCD. A moment later, the DCU gets
initialized properly.
This patch enables the pixel clock after initialization of the DCU
control register. This avoids this initial flicker on LCD screens.
While at it change the polarity of pixel clock to display samples
data on the rising edge.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Reviewed-by: Alison Wang <alison.wang@nxp.com>
Fix the framebuffer location to the very end of the available memory.
This allows to remove the area from available memory for the kernel,
which in turn allows to display the splash screen through the Linux
kernel boot process.
Ideas has been taken from the sunxi display driver, e.g.
20779ec3a5 ("sunxi: video: Dynamically reserve framebuffer memory")
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
sdhci_transfer_data() function transfers the blocks passed up to the
number of blocks defined in mmc_data, but returns immediately once all
the blocks are transferred, even if the loop exit condition is not met
(bit SDHCI_INT_DATA_END set in the STATUS word).
When doing multiple writes to mmc, returning right after the last block
is transferred can cause the write to fail when sending the
MMC_CMD_STOP_TRANSMISSION command right after the
MMC_CMD_WRITE_MULTIPLE_BLOCK command, leaving the mmc driver in an
unconsistent state until reboot. This error was observed in the rpi3
board.
This patch waits for the SDHCI_INT_DATA_END bit to be set even after
sending all the blocks.
Test: Reliably wrote 2GiB of data to mmc in a rpi3.
Signed-off-by: Alex Deymo <deymo@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The linux kernel driver for this module does not use a delay when
writing to the SDHCI_BUFFER register. This patch mimics that behavior
in order to speed up the mmc writes on the Raspberry Pi.
Signed-off-by: Alex Deymo <deymo@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the driver model support for Atmel mci while retaining the
existing legacy code. This allows the driver to support boards
that have converted to driver model as well as those that have not.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This driver implements MMC support on Meson GX (S905) based systems.
It's based on Carlo Caione's work, changes:
- BLK support added
- general refactoring
Signed-off-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
As a prerequisite for adding a Meson GX MMC driver update the
Meson GXBB / Odroid-C2 device tree in Uboot with the latest
version from Linux.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Enable the early debug UART to debug problems when an ICE or other
debug mechanism is not available.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Due to the introduction of the pinctrl and clk driver, and using
device tree files, remove the unneeded hardcoded pin configuration
and clock enabling code from the board file.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Update the configuration files to support the device tree and driver
model, so do SPL. The device clock and pins configuration are handled
by the clock and the pinctrl drivers respectively.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Enable the early debug UART to debug problems when an ICE or other
debug mechanism is not available.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Due to the introduction of the pinctrl and clk driver, and using
device tree files, remove the unneeded hardcoded pin configuration
and clock enabling code from the board file.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Update the configuration files to support the device tree and
driver model, so do SPL. The device clock and pins configuration
are handled by the clock and the pinctrl drivers respectively.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Add #ifndef CONFIG_DM_GPIO for CONFIG_AT91_GPIO define to avoid
the redefine compilation error.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
The MMC SPL locates the BSS section to a different memory region
from text, then use "_image_binary_end" variable to point to the
correct device tree location.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Because the MMC SPL puts the bbs section in the ddr memory, move
calling mem_init() before calling spl_init().
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
When OF_CONTROL is enabled, MMC boot device should not be detected
automatically, it should be MMC1 fixedly only the status "enabled"
is available.
Add NAND Flash boot device as well.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Add the device tree file for sama5d4ek board.
The dts file is copied from Linux-4.4, do the following changes.
- add the "u-boot,dm-pre-reloc" property to determine which nodes
which are needed by SPL and by the board_init_f stage.
- fix the compilation warning.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Add the device tree files for sama5d4 Xplained board.
The dts files are copied from Linux-4.4, do the following changes.
- add reg property for pinctrl node.
- move the gpio nodes(pioA, pioB, pioC ...) from the pinctrl child's
nodes to its slibling nodes.
- add the "u-boot,dm-pre-reloc" property to determine which nodes
which are needed by SPL and by the board_init_f stage.
- fix the compilation warnings.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Add the device tree file for sama5d3 Xplained board.
The dts files are copied from the Linux-4.9, do changes as below.
- add the "u-boot,dm-pre-reloc" property to determine which nodes
which are needed by SPL and by the board_init_f stage.
- fix the compile warning.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Add the device tree files for sama5d3xek board.
The dts files are copied from Linux-4.9, do the changes as below.
- add reg property for the pinctrl node.
- move the gpio nodes (pioA, pioB, pioC ...) as the pinctrl's
slibling nodes.
- add the "u-boot,dm-pre-reloc" property to determine which nodes
which are needed by SPL and by the board_init_f stage.
- fix the compile warning.
- add spi0 node aliases.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
AT91 PIO controller is a combined gpio-controller, pin-mux and
pin-config module. The peripheral's pins are assigned through
per-pin based muxing logic.
Each SoC will have to describe the its limitation and pin
configuration via device tree. This will allow to do not need
to touch the C code when adding new SoC if the IP version is
supported.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The intention of the removal is the preparation to introduce the
new AT91 PIO pinctrl driver.
Use the union to make the PIO3 and PIO2's registers be together
and make their offset aligned.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Because there isn't the implementation of gpio_set/get_value()
and gpio_set/get_value() after the at91 gpio driver is converted
to support the driver model, use at91_set_gpio_value() and
at91_get_gpio_value()
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When the CONFIG_ATMEL_LEGACY is undefined, according to the following
defines, at91_set_gpio_value() references to at91_set_pio_value(x, y)
with two parameters.
#define at91_set_gpio_value(x, y) at91_set_pio_value(x, y)
#define at91_get_gpio_value(x) at91_get_pio_value(x)
But there isn't the implementation of at91_set_pio_value(x, y) with
two parameters in U-Boot. This is an error.
Same as at91_get_gpio_value(x) define.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
One of these has crept in in this commit:
40a808f1 ARCv2: SLC: Make sure busy bit is set properly on SLC flushing
Adjust buildman to handle it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Not force to use python from PATH. Issue was noted when building with
Yocto, because python from the distro is always taken instead of
python-native built during Yocto process.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
There is a strange interaction with drivers which use DMA if the cache
starts off in a dirty state. Buffer space which the driver reads (but has
not previously written) can contain zero bytes from alloc_priv(). This can
cause corruption of the memory used by DMA for incoming data.
Fix this and add a comment to explain the problem.
This allows the dwc2 driver to work correctly with driver model, for
example.
Signed-off-by: Simon Glass <sjg@chromium.org>
uclass_find_device_by_seq() prints seq and req_seq when debugging is
enabled, but this information is not very useful by itself. Add the
name of he driver to this information. This improves debugging as it
shows which devices are being considered.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Acked-by: Simon Glass <sjg@chromium.org>
With skeleton.dtsi being dropped it is more likely that the /aliases node
will be last in the device tree. Update fdtgrep to handle this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
With Python 3.5.2 encode will throw an exception if val is a byte array.
Decode it to a string first. This assumes it's utf-8, if it's not valid
utf-8 it will throw an exception.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
os.read() returns a byte array in Python 3.5.2 and needs to be converted
into a string. Check if the returned value is an instance of bytes and
if it is decode it as a utf-8 string. If it is not a utf-8 encoded string
the decoding may fail with an exception.
Prior to this fix the comparisions check data == "" would fail when data
was b'' and would cause an infinite memory leaking loop. joins would
also fail with an exception below but due to the infinite loop it never
made it that far.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Do not condition the compilation of the U_BOOT_DRIVER by !OF_PLATDATA.
This is inconsistent with the majority of other drivers. This also
blocks OF_PLATDATA boards with an 16550-compatible serial from using
serial in SPL.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Added tweak for rock to avoid a TPL build failure:
Signed-off-by: Simon Glass <sjg@chromium.org>
Instead of having CONFIG_SANDBOX_BITS_PER_LONG in sandbox.h set to 64
with a comment to change to 32 on a 32bit host, simply set this to 64 in
asm/types.h and have the comment be there.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add support for %p, %pa[p], %pM, %pm and %pI4 formats to tiny-printf.
%pM and %pI4 are widely used by SPL networking stack and is required if
networking support is desired in SPL.
%p, %pa and %pap are mostly used by debug prints and hence supported
only when DEBUG is enabled.
Before this patch:
$ size spl/u-boot-spl
text data bss dec hex filename
99325 4899 218584 322808 4ecf8 spl/u-boot-spl
After this patch (with CONFIG_SPL_NET_SUPPORT):
$ size spl/u-boot-spl
text data bss dec hex filename
99666 4899 218584 323149 4ee4d spl/u-boot-spl
So, this patch adds ~350 bytes to code size.
If CONFIG_SPL_NET_SUPPORT is not enabled, this adds ~25 bytes.
If CONFIG_USE_TINY_PRINTF is disabled then:
$ size spl/u-boot-spl
text data bss dec hex filename
101116 4899 218584 324599 4f3f7 spl/u-boot-spl
So, there is still ~1.4K space saved even with support for %pM/%pI4.
Compiler used is to build is:
arm-linux-gnueabihf-gcc (Linaro GCC 6.2-2016.11) 6.2.1 20161016
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
I don't have the hardware test this, but it is almost certainly a typo
in the code dating back to at least 2004.
Signed-off-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
This allows us to use the same DRAM init function on all archs. Add a
dummy function for arc, which does not use DRAM init here.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Dummy function on nios2]
Signed-off-by: Tom Rini <trini@konsulko.com>
This function name shadows a global name but is in fact different. This
is very confusing. Rename it to help with the following refactoring.
Signed-off-by: Simon Glass <sjg@chromium.org>
Spam detection software, running on the system "lists.denx.de",
has identified this incoming email as possible spam. The original
message has been attached to this so you can view it or label
similar future email. If you have any questions, see
@@CONTACT_ADDRESS@@ for details.
Content preview: Previous change to create _printch causes the stack to be
used, breaking printch before stack is available. Inline _printch to prevent
this happening. Signed-off-by: Tim Chick <tim.chick@mediatek.com> --- [...]
Content analysis details: (6.3 points, 5.0 required)
pts rule name description
---- ---------------------- --------------------------------------------------
0.7 RCVD_IN_XBL RBL: Received via a relay in Spamhaus XBL
[188.29.165.105 listed in zen.spamhaus.org]
3.6 RCVD_IN_PBL RBL: Received via a relay in Spamhaus PBL
1.6 RCVD_IN_BRBL_LASTEXT RBL: No description available.
[188.29.165.105 listed in bb.barracudacentral.org]
0.4 RDNS_DYNAMIC Delivered to internal network by host with
dynamic-looking rDNS
Previous change to create _printch causes the stack to be used,
breaking printch before stack is available. Inline _printch to
prevent this happening.
Signed-off-by: Tim Chick <tim.chick@mediatek.com>
fw_env_open allocates buffers to store the environment, but these
buffers are never freed. This becomes quite nasty using the fw_ tools as
library, because each access to the environment (even just reading a
variable) generates a memory leak equal to the size of the environment.
Fix this renaming fw_env_close() as fw_env_flush(), because the function
really flushes the environment from RAM to storage, and add a
fw_env_close function to free the allocated resources.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Changes in the environment library are difficult to tracked by programs
using the library. Add simply an API version number that must be
increased each time when the API is changed.
This can be detected and a program can work with different versions of
the library.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Move U-Boot private data into a separate file. This
lets export fw_env.h to be used by external programs
that want to change the environment using the library
built in tools/env.
Signed-off-by: Stefano Babic <sbabic@denx.de>
aes.h is a too generic name if this file can
be exported and used by a program.
Rename it to avoid any conflicts with
other files (for example, from openSSL).
Signed-off-by: Stefano Babic <sbabic@denx.de>
Logic PD has an i.MX6Q system on module (SOM) with a development kit. The
SOM has a built-in microSD socket, DDR and NAND flash. The development kit
has an SMSC Ethernet PHY, serial debug port and a variety of peripherals.
This have been verified to boot the i.MX6Q version over either SD
on the development kit or NAND built into the SOM. Items in the dtsi file
are specific to the SOM itself. Items in the dts file are in the baseboard.
Future versions of the SOM will come out supporting the same basebord and
potentially future base boards will come out supporting the same SOM.
Signed-off-by: Adam Ford <aford173@gmail.com>
The handler do_setdsr receives only the dsr parameter,
the action is parsed before.
Error was introduced when restructuring the mmc command
implementation in commit 1fd93c6e7d.
Reported-by: Michael Krummsdorf <Michael.Krummsdorf@tq-group.com>
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
The num/denom is a float value, but in the calculation it is convert
to integer 0, and wrong result.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
By default, u-boot itself outputs on the serial console at 115200, so
it may as well pass the same value to the booted operating system as
well.
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Apply the proper setting for the reserved bits in SetDes Test and System Mode Control register
to avoid the voltage peak issue while we do the IEEE PHY comformance test
Signed-off-by: Ken Lin <yungching0725@gmail.com>
Acked-by: Akshay Bhat <akshay.bhat@timesys.com>
Add the delay (10ms) to ensure the clock is stable and to meet the clock-to-reset(1ms) requirement recommended in the AR8033 datasheet
Signed-off-by: Ken Lin <yungching0725@gmail.com>
Acked-by: Akshay Bhat <akshay.bhat@timesys.com>
Change the PMIC bulk configuration from auto mode to sync mode to avoid the voltage shutdown issue
Signed-off-by: Ken Lin <yungching0725@gmail.com>
Acked-by: Akshay Bhat <akshay.bhat@timesys.com>
Add the configuration options for display initialization in case we need to
do the display initialization in kernel to support different timing settings
Signed-off-by: Ken Lin <yungching0725@gmail.com>
Acked-by: Akshay Bhat <akshay.bhat@timesys.com>
- Remove arch/arm/cpu/arm926ejs/imx/ which is not available
- arch/arm/cpu/imx-common/ => arch/arm/imx-common/
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
As reported in STAR 9001165532, an SLC control reg read (for checking
busy state) right after SLC invalidate command may incorrectly return
NOT busy causing software to NOT spin-wait while operation is underway.
(and for some reason this only happens if L1 cache is also disabled - as
required by IOC programming model)
Suggested workaround is to do an additional Control Reg read, which
ensures the 2nd read gets the right status.
Same fix made in Linux kernel:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=c70c473396cbdec1168a6eff60e13029c0916854
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
For some reason Python 3 seems to think it does not need to build
the library. Using the --force parameter makes sure that the library
gets built always. This is especially important since we move the
library in the next step of the Makefile, hence forcing a rebuild
every time the higher level Makefile triggers a rebuild is required
to make sure the library is always there.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Simon Glass <sjg@chromium.org>
Since Binutils 1a9ccd70f9a7[1] u-boot will not link targets that set
CONFIG_SYS_TEXT_BASE=0 with the following error:
LD u-boot
arm-linux-gnueabi-ld.bfd: u-boot: Not enough room for program headers, try
linking with -N
arm-linux-gnueabi-ld.bfd: final link failed: Bad value
The issue can be reproduced with the bad binutils and the rock2_defconfig
target.
This issue was also encountered by the powerpc kernel[2], with the fix
being to pass --no-dynamic-linker for linkers newer than 2.26 when this
flag was introduced. The option tells ld that the PIE or shared lib does
not need loaded program headers.
Ubuntu Zesty's Binutils 2.27.51.20161202 hits this error.
[1] https://sourceware.org/git/gitweb.cgi?p=binutils-gdb.git;a=commit;h=1a9ccd70f9a7
[2] https://git.kernel.org/cgit/linux/kernel/git/powerpc/linux.git/commit/?h=next&id=ff45000fcb56b5b0f1a14a865d3541746d838a0a
Signed-off-by: Joel Stanley <joel@jms.id.au>
[AF: Apply to LDFLAGS_$(SPL_BIN) as well, suggested by Tom Rini]
Signed-off-by: Andreas Färber <afaerber@suse.de>
This simple PMU driver allows to tyrn power on and off for selected
devices. In particularly Intel Tangier needs to power on SDHCI
controllers in order to access to them during board initialization.
In the future it might be expanded to cover other Intel MID platforms,
that's why it's located under arch/x86/lib and called pmu.c.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a specific serial driver for Intel MID platforms.
It has special fractional divider which can be programmed via UART_PS,
UART_MUL, and UART_DIV registers.
The UART clock is calculated as
UART clock = XTAL * UART_MUL / UART_DIV
The baudrate is calculated as
baud rate = UART clock / UART_PS / DLAB
Initialize fractional divider correctly for Intel Edison platform.
For backward compatibility we have to set initial DLAB value to 16
and speed to 115200 baud, where initial frequency is 29491200Hz, and
XTAL frequency is 38.4MHz.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
With recent changes, some x86-specific rom tests of binman fail to
run. Fix it by adding missing filenames in corresponding entries.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Checking 'is_zimage' at this time will always fail and therefore booting
a FIT style image will always lead to this error message:
"## Kernel loading failed (missing x86 kernel setup) ..."
This change now removes this check and booting of FIT images works just
fine.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Now that we have added file names from Kconfig in x86 u-boot.dtsi,
update binman to avoid using hard-coded names.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Since we now have the file names configurable via Kconfig for the flash
descriptor and intel-me files, add these from Kconfig in the corresponding
dts nodes.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This introduces two Kconfig options to enable board specific filenames
for the Intel binary blobs to be used to generate the SPI flash image.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present there are only 8-bit and 32-bit read/write routines in
the rtc uclass driver. This adds the 16-bit support.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move the OPTEE load address to 0xbdb00000 in order to avoid
overlap with the memory regions used in radio and RVC usecases.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Move the OPTEE load address to 0xbdb00000 in order to avoid
overlap with the memory regions used in radio and RVC usecases.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Enable SPL_USB_HOST_SUPPORT in the default defconfig to allow
booting from USB peripherals. Unlike the non-HS boards, we
already load SPL to a 0x4030_0000+ address, so no other changes
are needed.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Additions have been made to the non-HS defconfig without the same
being made to the HS defconfig, sync them.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Additions have been made to the non-HS defconfig without the same
being made to the HS defconfig, sync them.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Additions have been made to the non-HS defconfig without the same
being made to the HS defconfig, sync them.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Sync new additions to non-HS defconfig with HS defconfig. Also add SPL
NAND support, this was disabled before due to size constraints, enable
this now at the expense of the less used GPT partition support.
Signed-off-by: Andrew F. Davis <afd@ti.com>
FIT support in the net boot case is much like the RAM boot case in that
we load our image to "load_addr" and pass a dummy read function into
"spl_load_simple_fit()". As the load address is no longer hard-coded to
the final execution address, legacy image loading will require load_addr
to be set correctly in the image header.
Signed-off-by: Andrew F. Davis <afd@ti.com>
TI K2G secure devices have to be built with TI_SECURE_DEVICE, FIT, and
FIT_IMAGE_POST_PROCESS enabled. Add a dedicated defconfig for this.
Signed-off-by: Andrew F. Davis <afd@ti.com>
TI K2HK secure devices have to be built with TI_SECURE_DEVICE, FIT, and
FIT_IMAGE_POST_PROCESS enabled. Add a dedicated defconfig for this.
Signed-off-by: Andrew F. Davis <afd@ti.com>
TI K2E secure devices have to be built with TI_SECURE_DEVICE, FIT, and
FIT_IMAGE_POST_PROCESS enabled. Add a dedicated defconfig for this.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch makes SYS_TEXT_BASE a config option for Keystone2
so that it can be used to load u-boot at different addresses
on secure and non-secure Keystone2 devices.
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Add a section describing the secure boot image used on
Keystone2 secure devices.
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Adds an additional image type needed for supporting secure keystone
devices. The build generates u-boot_HS_MLO which can be used to boot
from all media on secure keystone devices.
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
As K2 can directly boot U-Boot, add u-boot_HS_MLO as the secure image
name for secure K2 devices, for all boot modes other than SPI flash.
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Like the OMAP54xx, AM43xx, & AM33xx family SoCs, the keystone family
of SoCs also have high security enabled models. Allow K2E devices to
be built with HS Device Type Support.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
This commit implements the board_fit_image_post_process() function for
the keystone architecture. This function calls into the secure boot
monitor for secure authentication/decryption of the image. All needed
work is handled by the boot monitor and, depending on the keystone
platform, the security functions may be offloaded to other secure
processing elements in the SoC.
The boot monitor acts as the gateway to these secure functions and the
boot monitor for secure devices is available as part of the SECDEV
package for KS2. For more details refer doc/README.ti-secure
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The function 'board_fit_image_post_process' is defined only when the
config option CONFIG_FIT_IMAGE_POST_PROCESS is enabled. For secure
systems that do not use SPL but do use FIT kernel images, only
CONFIG_FIT_IMAGE_POST_PROCESS will be defined, which will result in an
implicit declaration of function 'board_fit_image_post_process' warning
while building u-boot. Fix this warning.
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The most common name for a FIT image containing a bootable kernel is
"fitImage", as our builds now use this name also, change this to the
default in our U-Boot environment.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Various commands to NAND flash results in the NAND flash becoming busy.
For those commands the SoC should wait until the NAND indicates it is
no longer busy before sending further commands. However, there is a delay
between the time the SoC sends its last command and when the NAND flash
sets its Ready/Busy Pin. This delay (tWB) must be respected or the SoC may
falsely assume the flash is ready when in reality it just hasn't had enough
time to indicate that it is busy.
Properly delaying by tWB is already done for nand_command/nand_command_lp
in nand_base.c including the version of it in the Linux kernel. Therefore,
this patch brings the handling of tWB delay inline to nand_base.c
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
[trini: Reformat comments slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that we have common MMC/SD boot environment
variables that can be used across TI platforms,
switch OMAP-L138 LCDK to use them.
As a nice side-effect, we get support for using
uEnv.txt on this platform.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Introduce include/environment/ti/mmc.h that
consolidates environment variable definitions
for various TI boards that support MMC/SD.
This allows reuse of same environment variables
on non-ARMv7 TI platforms like OMAP-L138 for
example.
While at it, move DFU-related environment variable
includes to only non-SPL builds for AM335x and
AM437x since they are not really used for SPL
today.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Use environment variables for various memory addresses
used on OMAP-L138 LCDK board. This makes it easy to
customize the boot process.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable some generic filesystem commands as
well as disk partition related commands for
OMAP-L138 LCDK board.
These help in booting Linux from MMC/SD, for
example.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
OMAP-L138 LCDK board does not have a SPI flash.
Remove spiboot related environment variable
definitions.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Up till this commit passing NULL as input parameter was allowed, but not
handled properly.
When one passed NULL to one of this function parameters, the code was
executed causing data abort.
However, what is more interesting, the abort was not caught because of code
execution in HYP mode with masked CPSR A bit ("Imprecise Data Abort mask bit).
The TI's AM57xx SoC switch to HYP mode with A bit masked in lowlevel_init.S
due to SMC call. Such operation (by default) is performed in SoC ROM code.
The problem would pop up when one:
- Switch back to SVC mode after disabling LPAE support
- Somebody enables A bit (by executing cpsie a asm instruction)
and then the previously described exception would be caught.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
The OMAP WDT IP block requires to be stopped before any write to its
registers is performed.
This problem has been thoroughly described in Linux kernel:
"watchdog: omap: assert the counter being stopped before reprogramming:
SHA1: 530c11d432727c697629ad5f9d00ee8e2864d453
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Under the plethora of #ifdefs, the xyzModem code hid this pearl:
static char *zm_out = (char *) 0x00380000;
This was only enabled when DEBUG is defined, so it's probably why it
went unnoticed for so long. No idea what platform had memory at that
exact location, but the this approach is extremely hacky.
Use a static buffer instead.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
spl_mmc.c calls mmc_initialize(). This symbol is provided in
drivers/mmc/mmc.c when CONFIG_GENERIC_MMC is enabled.
The sunxi Kconfig case is an oddball because it redefines
SPL_MMC_SUPPORT.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
[trini: Update arch/arm/cpu/armv8/zynqmp/Kconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
The default value of BOOTSTAGE_STASH_SIZE should be set to hexadecimal,
but an integer value is set. This fixes the BOOTSTAGE_STASH_SIZE number
from hexadecimal to integer.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
On ARM v7M, the processor will return to ARM mode when executing blx
instruction with bit 0 of the address == 0. Always set it to 1 to stay
in thumb mode.
Similar commit:
f99993c108
Author: Matt Porter <mporter@konsulko.com>
Date: Tue May 5 15:00:23 2015 -0400
common/cmd_boot: keep ARM v7M in thumb mode during do_go_exec()
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
ft_cpu_setup() already calls fdt_fixup_ethernet(), calling it
in image_setup_libfdt() is both redundant and breaks any modifications
done by ft_board_setup(). Restore the old behavior by removing
the call in image_setup_libfdt()
Fixes: 13d06981a9 ("image: Add device tree setup to image library")
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
The env command 'args_fit' does not define a root path, this forces us to
embed the rootfs into the FIT image. FIT images do not need to contain a
rootfs, when they do not the kernel will fall-back to the kernel argument
'root', if this is not defined the kernel will not boot. It is safe to
add this as when we do have the rootfs in FIT this argument is ignored.
As 'loadfit' is only called from the MMC boot path, use 'args_mmc' to
correctly populate 'bootargs'.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Good evening,
I am trying to port FreeBSD to the ASUS Tinker Board, a computer based
on the Rockchip 3288 SoC. FreeBSD's boot loader (named loader(8)) needs
CONFIG_API to be enabled, but trying to build an U-Boot from trunk with
both CONFIG_API and CONFIG_BLK (as required for Rockchip SoC's?) leads
to the following build failure:
$ CROSS_COMPILE=arm-none-eabi- gmake tinker-rk3288_defconfig all
...
CC api/api_storage.o
api/api_storage.c: In function 'dev_read_stor':
api/api_storage.c:334:9: error: 'struct blk_desc' has no member named 'block_read'
if ((dd->block_read) == NULL) {
^~
api/api_storage.c:339:11: error: 'struct blk_desc' has no member named 'block_read'
return dd->block_read(dd, start, len, buf);
^~
api/api_storage.c:340:1: warning: control reaches end of non-void function [-Wreturn-type]
}
^
gmake[2]: *** [scripts/Makefile.build:281: api/api_storage.o] Fehler 1
gmake[1]: *** [Makefile:1229: api] Fehler 2
gmake: *** [Makefile:460: __build_one_by_one] Error 2
I applied the following fix, but the product doesn't boot. Perhaps
that's not a property of the fix though:
Yours,
Robert Clausecker
As per the latest pinmux data available for AM572x EVM,
rev A3, input should be enabled on MMC clock lines for
MMC2/2/3 for stable operation.
Further, AM572x TRM, SPRUHZ6, Revised June 2016, in
section 18.4.6.1.1 "Pad Configuration Registers" states
that input should be enabled for MMC 2/3/4 clock lines.
Enable input on MMC1 and MMC3 clock to match the latest
pinmux data. Input is already enabled on MMC2 clock for
BeagleBoard x15. Further, input is already enabled on all
MMCx clocks for other AM57xx boards (AM572x and AM571x
IDK).
Tested with HS and UHS SD card on AM572x EVM Rev A3.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
SPI U-Boot image for K2 boards have now exceeded 512K partition
allocated to it and no longer fit the partitions defined in kernel DTS
file. Therefore, pass an updated MTD partition table from U-Boot as
kernel command line arguments to avoid kernel from accidentally
modifying boot loader image that has overflowed to next user partition.
To do is, introduce a common environment file for declaring SPI
partition so that each individual boards need not repeat the same.
Choose appropriate SPI bus from board config file and pass it as command
line argument to kernel.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Recent Linux distributions (e.g. Debian 9) include cross-compilers for
AArch64, but only for the aarch64-linux-gnu triplet only. It can thus
be expected that users will attempt to use the system cross-compiler
(instead of an aarch64-elf variant) to compile U-Boot for their ARMv8
target systems.
One key differences between an aarch64-linux-gnu and an aarch64-elf
compiler are the default settings regarding position-independent: with
the aarch64-linux-gnu compiler, the default will create and use the
global offset table.
This change-set adjusts the list of sections copied on ARMv8 to include
the GOT sections. With this added, the list matches the previous setup
for AArch32 closely.
Note that this is not an 'academic' issue, but was in fact encountered
by our QA during testing of the RK3399-Q7 BSP and resulted in an
early failure of the SPL stage during FDT setup.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
SPL has been restricted to use only dev 0 based on the assumption that only
one MMC device is registered. This is not always the case and many
platforms now register several devices as expected by the spl mmc boot code
For those platform SPL_ENV_SUPPORT is broken if dev is forced to 0.
A word of warning: this commit may break SPL_ENV_SUPPORT on platforms that
do not register the same MMC controllers in SPL and in u-boot (mostly iMX6
based platforms). Fortunately none of those activate SPL_ENV_SUPPORT in
their default configuration.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This enables the support for the Allwinner A23 Evaluation Board (EVB),
that already had a device tree (from Linux) but no defconfig.
This board has an AXP223 PMIC, some NAND, Audio out and in plugs, an
accelerometer and light sensor, as well as a USB HSIC hub and a USB
OTG mini-USB connector. It also has a Wifi/BT chip.
Access to the other buses (LCD, MIPI DSI, LVDS, etc) can be done
through dedicated pin headers.
Signed-off-by: Florent Jacquet <florent.jacquet@free-electrons.com>
Cc: Jagan Teki <jagan@openedev.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On boards that defines ENV_IS_NOWHERE, such as the NES classic, commit
19dbe7d1a3f7 ("common: Move environment choice to Kconfig") broke the build
because of a missing environment size.
Reintroduce a default environment size consistent with what we had before.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
If we depend on the ARCH_SUNXI configuration option, the boards that do not
have NAND support enabled (with the associated options) will not compile
anymore.
Depend on the NAND driver configuration option to make sure that is not the
case.
Reported-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
CMD_UBIFS can't compile without CMD_UBI enabled. Make sure we can't end up
in that case.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Heiko Schocher <hs@denx.de>
Recently some sunxi related code was moved to arch/arm/mach-sunxi, but
the MAINTAINERS entry was not updated to reflect this. Add this, and
the board level boards/sunxi directory to our entry.
While at it, also update its status, to reflect the current active
maintainership.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The Sunchip CX-A99 is a board used in some media players. It features:
An Allwinner A80 ARM SoC (4 * Cortex-A7 + 4 * Cortex-A15 cores)
2 GiB or 4 GiB DDR3 DRAM
AXP808 PMIC
16 GB or 32 GB eMMC
SDIO Wifi/Bluetooth/FM module
SD card slot
1 USB 3.0 connector
2 USB 2.0 connectors
SATA connector
UART connector (internally) for serial console
Ethernet connector (10/100/1000 Mbit/s)
HDMI connector
Composite video and analog audio connector
S/PDIF connector
IR remote control receiver
This patch adds a defconfig for the board. The DRAM settings are as found
in the vendor sys_config.fex file.
It has a preliminary device tree for use until a device tree is accepted
upstream, after which it can be replaced by the upstream version.
Signed-off-by: Rask Ingemann Lambertsen <rask@formelder.dk>
[squash commits, and edited new meanful commit message]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
commit 56b0730157f70dc23d6caff9e7ceb8b377b96b9f upstream.
On the A80, mmc1 is available on pingroup G. Designs mostly use this
to connect to an SDIO WiFi chip.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Rask Ingemann Lambertsen <rask@formelder.dk>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The CHIP Pro is a SoM that features the GR8 SIP, an AXP209, a BT/WiFi chip
and a 512MiB SLC NAND.
This it's an SLC NAND, it doesn't suffer the same drawbacks than found on
the MLC NANDs, and we can enable it right away.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Introduce a new sunxi-spl-with-ecc.bin image with already the right header,
ECC, randomizer and padding for the BROM to be able to read it.
It needs to be flashed using a raw access to the NAND so that the
controller doesn't change a thing to it, since we already have all the
right parameters.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
The default U-Boot offset for the Allwinner SoCs was set to 32kB.
This was probably to try to maintain some compatibility with the current
image that we build for the MMC where the U-Boot binary is also located at
a 32kB offset.
However, this causes a number of issues. The first one is that it prevents
us from using a backup SPL entirely, which is troublesome in case where the
first would be corrupt (especially on MLC which have a higher number of
bitflips).
We also cannot use the original MMC image on the NAND, because we need to
prepare the SPL image to include the ECCs and randomizer settings, which
reduces the interest of setting it at that particular offset.
It also prevents us from upgrading and flashing the U-Boot and SPLs
independantly, since it's very likely that it will fall in the same erase
block.
Since that default wasn't used by any board, change it for 8MB, which will
be in an erase block of its own, all the erase blocks being multiple of
two. The highest erase block size we encountered is 4MB, which means that
in this particular setup, the first and second erase blocks will be for the
SPL and its backup, and the third for U-Boot.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
CMD_MTDPARTS is something the user might or might not want to select, and
might depends on (or be selected by) other options too.
This is even truer for the MTDIDS_DEFAULT and MTDPARTS_DEFAULT options that
might change from one board to another, or from one user to the other,
depending on what it expects and what storage devices are available.
In order to ease that configuration, add those options to Kconfig.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The environment location is something that might change per board
(depending on what storage options are availaible there) or depending on
the user choice (when we have several options).
Instead of hardcoding it in our configuration header, create a Kconfig
choice with the options we use for now, and the symbols that depend on it.
Once done, also remove the irrelevant sunxi defines.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
We will need the bch functions in the tool to generate the SPL images for
the Allwinner SoCs.
Do the needed adjustments so that we can use it on the host.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
When trying to autodetect the ECC and randomization configurations, the
driver starts with a randomization disabled and no seeds.
In this case, the number of seeds is obviously 0, and the randomize boolean
is set to false.
However, the logic that retrieves the seed for a given page offset will
blindly use the number of seeds, without testing if the randomization is
enabled, basically doing a modulo by 0.
As it turns out, the libgcc in the common toolchain returns 0 here, which
was our expected value in such a case, and why we would not detect it.
However, U-Boot's libgcc will for some reason return from the function
instead, resulting in an error to load the U-Boot binary in the SPL.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Scott Wood <oss@buserror.net>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add support for the NanoPi NEO Air H3 board from friendlyarm.com . This
board contains WiFi, Bluetooth, 8GB eMMC storage and 512 MB DDR3 ram.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[Rebase on master]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This ports the support for configuring a GPIO for resetting the
Ethernet PHY (incl. such details as the reset polarity and
pulse-length) from the Designware driver.
X-AffectedPlatforms: A64-uQ7
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Remove the board_power_init() function.
It will be initialized with device-tree.
In future, it will be controlled with regulator API.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Remove the unused functions.
Never call the get_soft_i2c_scl/sda_pin() aynwhere.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Remove the board_i2c_init() function.
i2c should be initialized with device-tree file.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add the i2c-gpio nodes for fuelgauge and max77693.
There are i2c8 and i2c9.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
With d53ecad92f some unused interrupt related code was removed.
However all of these options are currently unused. Rather than migrate
some of these options to Kconfig we just remove the code in question.
The only related code changes here are that in some cases we use
CONFIG_STACKSIZE in non-IRQ related context. In these cases we rename
and move the value local to the code in question.
Fixes: d53ecad92f ("Merge branch 'master' of git://git.denx.de/u-boot-sunxi")
Signed-off-by: Tom Rini <trini@konsulko.com>
Add separate enable/disable controls for driver-model serial. While this
is generally enabled in SPL it may not be in TPL, since serial output can
be obtained with the debug UART with minimal code size.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since TPL often needs to be very very small it may not make sense to
enable driver model. Add an option for this.
This changes brings the 'rock' board under the TPL limit with gcc 4.9.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we have SPL_ which can be used in Makefiles to select between
normal and SPL CONFIGs like this:
obj-$(CONFIG_$(SPL_)DM) += core/
When TPL is being built, SPL_ has the value 'SPL' which is generally a
good idea since they tend to follow each other. But in extreme situations
we may want to distinugish between SPL and TPL. For example we may not
want to enable CONFIG_DM with TPL.
Add a new SPL_TPL_ variable which is set to either empty (for U-Boot
proper), 'SPL' or 'TPL'. This may prove useful with TPL-specific options.
Signed-off-by: Simon Glass <sjg@chromium.org>
These includes don't seem to be needed now. Drop them. Reserve the
mp.h header for PowerPC for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: York Sun <york.sun@nxp.com>
This header file is used by three archs. It could be used by all of them
since relocation is a common function. Move it into a generic file.
Signed-off-by: Simon Glass <sjg@chromium.org>
This header file is used by two archs. It could be used by all of them
since it allows the cache to be on during relocation. Move it into a
generic file.
Signed-off-by: Simon Glass <sjg@chromium.org>
We don't need this PPC-specific function in generic code. Move it to
the powerpc directory.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Drop headers which are not used or needed in this file. The compiler.h
header is included by common.h.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
This is an weak function present on all archs so we should have it in the
common header file. Remove it from arch-specific headers and add a
function comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
By making dram_init_banksize() return an error code we can drop the
wrapper. Adjust this and clean up all implementations.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Move the ugly #ifdefs inside the reserve_video() function so we can
collect all this init into one place.
Signed-off-by: Simon Glass <sjg@chromium.org>
The arch-specific details of the cache being off are best handled inside
the reserve_mmu(). This cleans up the init sequence a little.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
CONFIG_ALT_LB_ADDR is really a detail of how this logbuffer is allocated
rather than whether to do it at all. So move the #ifdef into the function.
Signed-off-by: Simon Glass <sjg@chromium.org>
All archs put U-Boot at the bottom of the relocated region. Xtensa does
not, but perhaps not for any good reason. Adjust it to see if things
still work OK.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we cannot use this function as an init sequence call without a
wrapper, since it returns the RAM size. Adjust it to set the RAM size in
global_data instead, and return 0 on success.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
It looks like only cm5200 and tqm8xx use this feature, so we don't really
need it in generic code. Drop it and have the users access gd->board_type
directly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This is not used by any board. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Clean up board_f sequence a little
This series tries to remove #ifdefs from the board_f init sequence. It
gets as far as I2C and then we need to discuss whether we can start to
remove the old I2C framework.
I think that ideally each entry in the init sequence should be enabled by
at most one CONFIG, which is in Kconfig and is not arch-specific.
END
Acked-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
At present we misuse print_cpuinfo() do so CPU init on x86. This is done
because it is the next available call after the console is enabled. But
several arches use checkcpu() instead. Despite the horrible name (which
we can fix), it seems a better choice.
Adjust the various x86 CPU implementations to move their init code into
checkcpu() and use print_cpuinfo() only for printing CPU info.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Move these two function calls into checkcpu(), which is called on this
arch immediately after these two.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
We don't need a special hook for sandbox as one of the later ones will do
just as well. We can print error messages about bad options after we
print the banner. In fact, it seems better.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Combine the conditions so this appears in the init list only once.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
More than half of the architectures use this function so let's make them
all use it.
For those which don't actually define it, we can rely on the weak function
in lib/time.c
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
There is no good reason to use a different name on PowerPC. Change it to
timer_init() like the others.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Now that both branches of the #if do the same thing, we can unify them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
We really don't need to have a name like this in the generic init
sequence. Use the generic get_clocks() name so that we can merge these
two at some point.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
We have two chunks of code which depend on this CONFIG options. There is
likely no need to keep them apart, so join them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
While x86 is the only user and this could in principle be moved to
arch_cpu_init() there is some justification for this being a separate
call. It provides a way to handle init which is not CPU-specific, but
must happen before the CPU can be set up.
Rename the function to be more generic.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
There is no need to have this call in the generic init sequence and no
other architecture has needed it in the time it has been there. Move it
into sandbox's private code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
When this board was switched to using more DM drivers we didn't disable
the legacy PCA953X driver. This in turn learn to a build time warning
about implicit functions as i2c.h would not say anything about
'i2c_read' nor 'i2c_write'. But this was not a fatal error as none of
the legacy driver would be linked in either.
Fixes: e389033f72 ("imx: mx6sxsabreauto: enable more dm drivers")
Reviewed-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
The OrangePi PC 2 is a typical SBC with the 64-bit Allwinner H5 SoC.
Add a (64-bit only) defconfig defining the required options to build
the U-Boot proper.
Create a new .dts file for it by including the (32-bit) H3 SoC .dtsi
and changing the differing components accordingly.
This is a preliminary device tree mostly for U-Boot's own sake, it
is expected to be updated once the official DT gets accepted upstream.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[squash the commits, update the commit message]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The Allwinner H5 Soc is bascially an H3 with high SRAM and ARMv8 cores.
As the peripherals and the pinmuxing are almost identical, we piggy
back on the shared MACH_SUN8I_H3_H5 config symbol.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The Allwinner H5 is very close to the H3 SoC, but has ARMv8 cores.
To allow sharing the clocks, GPIO and driver code easily, create an
architecture agnostic MACH_SUNXI_H3_H5 Kconfig symbol.
Rename the existing symbol to MACH_SUNXI_H3_H5 where code is shared and
let it be selected by a new shared Kconfig option.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The DRAM controller in the Allwinner H5 SoC is again very similar to
the one in the H3 and A64.
Based on the existing socid parameter, add support for this controller
by reusing the bulk of the code and only deviating where needed.
These new bits set or cleared here and there have been mostly found by
looking at DRAM register dumps after using the H5 boot0 and comparing
them to what we set in the code. So for now it's mostly unclear what
those bits actually mean - hence the missing names and comments.
Also add the delay line parameters taken from the boot0 and libdram
disassembly.
Register setup differences between H5 and H3 are courtesy of Jens Kuske.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Addresses passed on to readl and writel are expected to be of the same
size as a pointer. Change the parameter types of sunxi_spi0_read_data()
to make the compiler happy and allow a warning-free aarch64 compile.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Traditionally Allwinner SoCs have their boot ROM mapped just below 4GB,
while the first SRAM region is mapped at address 0.
With the extended physical memory support of the A80 this was changed,
so the BROM is now at address 0 and the SRAM region starts right behind
this at 64KB. This configuration seems to be called "high SRAM".
Instead of enumerating the SoCs which have copied this configuration,
let's call a spade a spade and introduce a Kconfig option for this setup.
SoCs implementing this (A80, A64 and H5, so far), can then select this
configuration.
Simplify the config header definition on the way.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
For some reason we were pretty conservative when defining the maximum
SPL size for the Allwinner A80(sun9i) SoC.
According to the manual the SRAM A1 is even 40KB, but the BROM
probably still has the 32 KiB load limit. For the sake of simplicity,
merge the SPL memory definitions for the A64 and A80 SoCs, since both
SoC share the BROM/SRAM A1 memory layout.
This helps to further simplify this is in the next patch.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Instead of enumerating all SoC families that need that bit set, let's
just express this more clearly: The SMP bits needs to be set on
SMP capable ARMv7 CPUs. It's much easier in Kconfig to express it the
other way round, so we use ! CPU_IS_UP and ! ARM64.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some Freescale boards used an extra version of the constant to hold the
Generic Timer frequency. This can easily be covered by the now unified
COUNTER_FREQUENCY constant, so remove this extra variable from those
boards.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Many ARMv8 boards define a constant COUNTER_FREQUENCY to specify the
frequency of the ARM Generic Timer (aka. arch timer).
ARMv7 boards traditionally used CONFIG_TIMER_CLK_FREQ for the same
purpose. It seems useful to unify them.
Since there are less occurences of the latter version, lets convert all
users over to COUNTER_FREQUENCY.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
If we take the liberty to use register r0 to perform our bit set, we
should be nice enough to tell the compiler about it.
Add r0 to the clobber list to avoid potential mayhem.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Jagan Teki <jagan@openedev.com>
This patch replaces SPL_PINCTRL_FULL with SPL_PINCNTRL. It is to avoid removal
of pin control properties in case of SPL_PINCTRL. No impact in case of
SPL_PINCTRL_FULL as it depends on SPL_PINCTRL.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a test for the correct device removal. Currently two different ways
for device removal are supported:
- Normal device removal via the device_remove() API
- Removal via selective device driver flags (DM_FLAG_ACTIVE_DMA)
This new test "remove_active_dma" adds tests cases for those both ways
of removal. This is done by adding a new test driver, which has this
flag set.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
This patch adds a call to dm_remove_devices_flags() to
announce_and_cleanup() so that drivers that have one of the removal flags
set (e.g. DM_FLAG_ACTIVE_DMA_REMOVE) in their driver struct, may do some
last-stage cleanup before the OS is started.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The new function dm_remove_devices_flags() is intented for driver specific
last-stage cleanup operations before the OS is started. This patch adds
this functionality and hooks it into the common device_remove()
function.
Drivers wanting to use this feature for some last-stage removal calls,
need to add one of the DM_REMOVE_xx flags to their driver .flags.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds the flags parameter to device_remove() and changes all
calls to this function to provide the default value of DM_REMOVE_NORMAL
for "normal" device removal.
This is in preparation for the driver specific pre-OS (e.g. DMA
cancelling) remove support.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
MiQi is rk3288 based development board with 1 or 2 GB SDRAM, 16 GB eMMC,
micro SD card interface, 4 USB 2.0 ports, HDMI, gigabit Ethernet and
expansion ports.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Eddie Cai <eddie.cai.linux@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The (shared) rk3399.dtsi had defined the 'rockchip,vbus-gpio'
properties for each USB 3.0 controller.
As the GPIO usage will vary (e.g. one of those GPIOs shuts down one of
the regulators on the RK3399-Q7) between boards, we move this from the
shared dtsi into the device tree file for the EVB board which these
GPIO definitions match.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit adds the baseline defconfig for the RK3399-Q7 (Puma) SoM
(under the name 'puma-rk3399_defconfig') featuring the Rockchip RK3399
in a Qseven compatible module.
This subsumes the following changes:
* defconfig: rk3399: migrate CONFIG_SPL_LIBCOMMON_SUPPORT/CONFIG_SPL_LIBGENERIC_SUPPORT
* defconfig: rk3399-puma: add CONFIG_MMC_DW_ROCKCHIP
* defconfig: rk3399-puma: disable CONFIG_SPL_OF_PLATDATA
* defconfig: rk3399-puma: don't USE_TINY_PRINTF
* defconfig: rk3399-puma: set up CONFIG_SYS_BOARD for the RK3399-Q7
* defconfig: rk3399-puma: enable the multi-image loading via CONFIG_SPL_FIT
* defconfig: rk3399-puma: SPL should be able to boot from MMC/SD card
* defconfig: rk3399-puma: enable GMAC support
* defconfig: rk3399-puma: enable support for SPI and Winbond SPI flash
* defconfig: rk3399-puma: enable SPI as a boot-source in SPL
* defconfig: rk3399-puma: disallow non-FIT images from being loaded
* defconfig: rk3399-puma: rename to puma-rk3399
* rockchip: config: rk3399: update defconfigs and rk3399_common
For the RK3399-Q7, we want a default boot-order of SPI -> MMC -> uSD.
This both follows how the BootROM probes devices and is a sane default
for customers in device-personalisation (e.g. it allows for quick and
easy factory programming of unpersonalised devices using an SD card)
and field usage (with customer devices expected to have their firmware
either in SPI or MMC).
However, when probing multiple interfaces (according to the result
from the board_boot_order function), we need to ensure that only valid
FIT images are considered and disable the fallback to assuming that a
raw (binary-only) U-Boot image is loaded (to avoid hangs/crashes from
jumping to random content loaded from devices that are probed, but
don't contain valid image content).
By disabling the SPL_RAW_IMAGE_SUPPORT and SPL_LEGACY_IMAGE_SUPPORT
options, we ensure that raw images (indistinguishable from random
data) are not considered for booting.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
Drop CONFIG_DEBUG_UART_BOARD_INIT:
Signed-off-by: Simon Glass <sjg@chromium.org>
The RK3399-Q7 is a system-on-module featuring the Rockchip RK3399
in a Qseven-compatible form-factor.
These changes add a device-tree describing the board and its
interfaces for basic functionality (e.g. GbE, SPI, eMMC, SD-card).
This includes the following changes from the original development:
* dts: rk3399-puma: include DTS for RK3399-Q7 SoM in the Makefile
* dts: rk3399-puma: add gmac for the RK3399-Q7
This change enables the Gigabit Ethernet support on the RK3399-Q7.
* dts: rk3399-puma: use serial0 for stdout
* dts: rk3399-puma: prepare the sdmmc node for SPL booting
* dts: rk3399-puma: enable spi1 and spi5, add /spi1/spiflash
The RK3399-Q7 (Puma) unsually (this is a build-time option for
customised boards) has an on-module SPI-flash connected to SPI1.
As of today, this is a Winbond W25Q32DW (32MBit) device.
The SPI5 controller is routed to the Q7 edge connector and provides
general-purpose SPI connectivity for customer base-boards.
With some minor improvements on integration into our outbound tree
- explicitly modelled the SPI flash as 'spiflash' under spi0
[dts: rk3399-puma: explicitly model spi-flash under spi1]
- renamed the aliases to spi0 and spi1 to allow easier use of
commands and legacy (SPL) infrastructure... i.e. the controllers
will be 0 and 1 for 'sf probe', 'sspi', etc.
[dts: rk3399-puma: rename aliases to number spi as 0 and 1 for commands]
* dts: rk3399-puma: include SPI in the spl-boot-order property
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
On the RK3399-Q7 we need to enable a number of configuration options
(e.g. CONFIG_SPI_FLASH_WINBND) dependent on Kconfig seeing CONFIG_SPI
and CONFIG_SPI_FLASH active.
To allow for these being defined in Kconfig (e.g. via defconfig) and
to avoid a warning on having the macro defined multiple times, we
remove them from the common header file.
Note that the rk3399-evb does not currently have the rk_spi.c driver
active (i.e. CONFIG_ROCKCHIP_SPI), so there's no change to the
evb-rk3399_defconfig as part of this change.
X-AffectedPlatforms: RK3399-Q7
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
For the initial validation of the RK3399-Q7 (Puma), the DDR3 has been
clocked at 666MHz (i.e. DDR3-1333) using the same (safe) settings as
used in Rockchip's MiniLoader.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
The RK3399 does not have any boot selection pins and the BootROM probes
the boot interfaces using the following boot-order:
1. SPI
2. eMMC (sdhci in DTS)
3. SD card (sdmmc in DTS)
4. USB loader
For ease of deployment, the SPL stage should mirror the boot order of
the ROM and use the same probing order (assuming that valid images can
be detected by SPL) unless instructed otherwise. The boot-order can
then be configured via the 'u-boot,spl-boot-order' property in the
chosen-node of the DTS.
While this approach is easily extensible to other boards, it is only
implemented for the RK3399 for now, as the large SRAM on the RK3399
makes this easy to fit the needed infrastructure into SPL and our
production setup already runs with DM, OF_CONTROL and BLK in SPL.
The new boot-order property is expected to be used in conjunction with
FIT images (and all legacy image formats disabled via Kconfig).
A boot-sequence with probing and fallthroughs from SPI via eMMC to SD
card (i.e. &spiflash, &sdhci, &sdmmc) has been validated on the RK3399-Q7.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Tested-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
The Rock is a RK3188 based single board computer by Radxa.
Currently it still relies on the proprietary DDR init and
cannot use the generic SPL, but at least is able to boot
a linux kernel and system up to a regular login prompt.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Fix sort order in defconfig, enable CONFIG_SPL_TINY_MEMSET:
Signed-off-by: Simon Glass <sjg@chromium.org>
Most of the time the optimised memset() is what we want. For extreme
situations such as TPL it may be too large. For example on the 'rock'
board, using a simple loop saves a useful 48 bytes. With gcc 4.9 and
the rodata bug, this patch is enough to reduce the TPL image below the
limit.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
At present we sometimes see the following build error when building on a
machine with multiple cores.
+make[2]: *** No rule to make target 'dts/dt.dtb', needed by 'tpl/u-boot-tpl.dtb'. Stop.
Add a dependency to correct this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Commit 3a649407a4 ("arm: Migrate SYS_THUMB_BUILD to Kconfig, introduce
SPL_SYS_THUMB_BUILD") moved the THUMB_BUILD symbols from the header to
Kconfig symbols. With it still defined in the rk3188 header we end up
with a duplicate symbol and compile errors, so fix that.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
The clock driver for the RK3399 mistakenly used (24 * 2^20) where it
should have used (24 * 10^6) in a few calculations.
This commits fixes this.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
The GMAC in the RK3399 is very similar to the RK3288 variant (i.e. it
is a Designware GMAC core and requires similar configuration as the
RK3288 to switch it to RGMII and set up the TX/RX delays for Gigabit).
The key difference is that the register offsets (within the GRF block)
and bit-offsets (within those registers) used to hold the configuration
differ between the various RK32/33 CPUs.
This change refactors the gmac_rockchip.c driver to use a function
table (selected via driver_data) to factor out these differences. Each
function's implementation then matches the underlying processor.
Some collateral changes are needed in the definitions describing the
bits and offsets in the GRF are needed to prefix each set of symbolic
constants with the SoC name to avoid name clashes... and in doing so,
the shifts for masks and constants have been moved into the header
files for readability (and to make it easier to stay below 80 chars).
X-AffectedPlatforms: RK3399-Q7
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Fixed commit message typo s/factor our/factor out/:
Signed-off-by: Simon Glass <sjg@chromium.org>
The Ethernet driver for the RK3288/3399 GMAC makes sure that the clock
is ungated through a call to clk_set_rate(...). Even though nothing
needs to be done on the RK3399 (the clock gates are open and the clock
is external), we need to implement enough support to at least return
success to enable driver probing.
X-AffectedPlatforms: RK3399-Q7
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
Due to differences in the code paths for SPL and non-SPL, some static
constant structures remain unused in each build variant. This raises
warnings with recent GCC versions (we currently use GCC-6.3).
The warnings addressed in this commit (by matching #if conditions for
the variable definition with their uses) are:
* for the SPL build:
drivers/clk/rockchip/clk_rk3399.c:53:29: warning: 'cpll_init_cfg' defined but not used [-Wunused-const-variable=]
static const struct pll_div cpll_init_cfg = PLL_DIVISORS(CPLL_HZ, 1, 2, 2);
^~~~~~~~~~~~~
drivers/clk/rockchip/clk_rk3399.c:52:29: warning: 'gpll_init_cfg' defined but not used [-Wunused-const-variable=]
static const struct pll_div gpll_init_cfg = PLL_DIVISORS(GPLL_HZ, 2, 2, 1);
^~~~~~~~~~~~~
* for the non-SPL build:
drivers/clk/rockchip/clk_rk3399.c:54:29: warning: 'ppll_init_cfg' defined but not used [-Wunused-const-variable=]
static const struct pll_div ppll_init_cfg = PLL_DIVISORS(PPLL_HZ, 2, 2, 1);
^~~~~~~~~~~~~
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
To add GMAC (Gigabit Ethernet) support (limited to RGMII only at this
point), we need support for additional pin-configuration. This commit
adds the pinctrl support for GMAC in RGMII signalling mode:
* adds a PERIPH_ID_GMAC and the mapping from IRQ number to PERIPH_ID
* adds the required defines (in the GRF support) for configuring the
GPIOC pins for RGMII
* configures the RGMII pins (in GPIOC) when requested via pinctrl
X-AffectedPlatforms: RK3399-Q7
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
An earlier upstream change contained an unconditional debug message
which would show up as a message similar to the following in the
U-Boot startup (after the ATF and before the U-Boot banner):
time 159f019, 0
This commit removes this message (instead of making if conditional on
being a debug-build), as it doesn't pertain to any initialisation done
in this file.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
The BootROM of the RK3399 SoC does not initialise the cntfrq_el0 (which
holds the value 0 (zero) on entry into the SPL. This causes the timebase
for U-Boot not to advance (and will cause a hang where a timeout would
be expected... e.g. if something goes wrong during MMC/SD card startup).
This change defines COUNTER_FREQUENCY, which is used by the AArch64 init
code in arch/arm/cpu/armv8/start.S to set up cntfrq_el0 (if necessary).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
Designware HDMI controller and phy are used in other SoCs as well. Split
out platform independent code.
DW HDMI has 8 bit registers but they can be represented as 32 bit
registers as well. Add support to select access mode.
EDID reading code use reading by blocks which is not supported by other
SoCs in general. Make it more general using byte by byte approach, which
is also used in Linux driver.
Finally, not all DW HDMI controllers are accompanied with DW HDMI phy.
Support custom phys by making controller code independent from phy code.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Nickey Yang <nickey.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The Cortex-A9 socs rk3066 and rk3188 share the IP but have their own
compatible values, so add them to make the i2c on these platforms accessible.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
The armclk starts in slow mode (24MHz) on the rk3188, which results in U-Boot
startup taking a lot of time (U-Boot itself, but also the rc4 decoding done
in the bootrom).
With default pmic settings we can always reach a safe frequency of 600MHz
which is also the frequency the proprietary loader left the armclk at,
without needing access to the systems pmic.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
The armclk starts in slow mode (24MHz) on the rk3188, which makes the whole
startup take a lot of time. We therefore want to at least move to the safe
600MHz value we can use with default pmic settings.
This is also the freqency the proprietary sdram-init leaves the cpu at.
For boards that have pmic control later in u-boot, we also add the option
to set the maximum frequency of 1.6GHz, if they so desire.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
In the beginning, we did SPL -> TPL -> U-Boot, but after clarification
of the real ordering swapped SPL and TPL.
It seems some renames were forgotten and may confuse future readers, so
also swap these to reflect the actual ordering.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
There was still a static ram value set in the rk3188-board from the
time where we didn't have actual sdram init code.
Now the sdram init leaves the ram information in SYS_REG2 and we can
decode it similarly to the rk3288.
Right now we have two duplicates of that code, which is still ok and
doesn't really count as common code yet, but if we get a third copy
at some point from a newer soc, we should think about moving that to
a more general position.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
Right now we're setting the wrong value of 0 as base in the ram_info struct,
which is obviously wrong for the rk3188. So instead set the correct value
we already have in CONFIG_SYS_SDRAM_BASE.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
Building sd images for rk3188 requires more steps due to the needed split
into TPL and SPL as loaders. Describe how to build an image for it in a
separate paragraph in the READER.rockchip file.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Commit c67c8c604b ("board_init.c: Always use memset()") dropped the naive
memset alternative from board_init_f_init_reserve.
So activate CONFIG_TPL_LIBGENERIC for that common memset implementation.
We cannot use the ARCH-specific memset, as that would incur 200bytes of
additional TPL size, space we do not have.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The config options for pinctrl on the RK3188, RK3288, RK3328 and
RK3399 previously showed up in menuconfig with the generic string
descriptor "Rockchip pin control driver" requiring one to look through
the help/full description to identify which chip each menu entry was
for.
This change renames each option with the chip-name in the description
string to make it easy to identify the configuration options in
menuconfig.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
To simplify the creation of AArch64 SPL images for the RK3399, we
use the ENABLE_ARM_SOC_BOOT0_HOOK option and prepend 4 bytes of
padding at the start of the text section. This makes it easy for
mkimage to rewrite this word with the 'RK33' boot magic.
This change brings logic to calculate the header size and allocate
the header back in sync. For the RK3399 we now limit the header to
before the payload (i.e. the 'header0' and the padding up to the
actual image) and overwrite the first word (inserted by the
boot0-hook for this purpose) with the 'RK33' magic in-place.
X-AffectedPlatforms: RK3399-Q7
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
The SPL binary needs to be prefixed with the boot magic ('RK33' for
the RK3399) on the Rockchip platform and starts execution of the
instruction word following immediately after this boot magic.
This poses a challenge for AArch64 (ARMv8) binaries, as the .text
section would need to start on the odd address, violating natural
alignment (and potentially triggering a fault for any code that
tries to access 64bit values embedded in the .text section).
A quick and easy fix is to have the .text section include the 'RK33'
magic and pad it with a boot0 hook to insert 4 bytes of padding at the
start of the section (with the intention of having mkimage overwrite
this padding with the appropriate boot magic). This avoids having to
modify the linker scripts or more complex logic in mkimage.
X-AffectedPlatforms: RK3399-Q7
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
The RK3399 boot code (running as AArch64) poses a bit of a challenge
for SPL image generation:
* The BootROM will start execution right after the 4-byte header (at
the odd instruction word loaded into SRAM at 0xff8c2004, with the
'RK33' boot magic residing at 0xff8c2000).
* The default padding (during ELF generation) for AArch64 is 0x0,
which is an illegal instruction and the .text section needs to be
naturally aligned (someone might locate a 64bit constant relative
to the section start and unaligned loads trigger a fault for all
privileged modes of an ARMv8)... so we can't simply define the
CONFIG_SPL_TEXT_BASE option to the odd address (0xff8c2004).
* Finally, we don't want to change the values used for padding of
the SPL .text section for all ARMv8 targets to the instruction
word encoding 'nop', as this would affect all padding in this
section and might hide errors that would otherwise quickly trigger
an illegal insn exception.
To deal with this situation, we modify the rkimage generation to
- understand the fact that the RK3399 needs to pad the header to an
8 byte boundary using an AArch64 'nop'
- the necessary logic to adjust the header_size (which controls the
location where the payload is copied into the image) and to insert
this padding (AArch64 insn words are always little-endian) into
the image following the 4-byte header magic.
X-AffectedPlatforms: RK3399-Q7
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
The RC4 encoding works on full blocks, but the calculation of the
starting offset and size are needlessly complicated by using a
reference value known to be offset into a block by the size of the
header and then correcting for the (hard-coded) size of the header
(i.e. 4 bytes).
We change this over to use the RK_SPL_HDR_START directly (which is
known to be on a block boundary).
X-AffectedPlatforms: RK3399-Q7
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
we are using mmc alias , so mmc index have been changed.
now mmc dev 0 is emmc and mmc dev 1 is sdmmc.
Signed-off-by: Jacob Chen <jacob2.chen@rock-chips.com>
This includes Marvell mvpp2 patches with the ethernet support for the
ARMv8 Armada 7k/8k platforms. The ethernet patches are all acked by Joe
and he is okay with me pushing them via the Marvell tree.
Change the buck8's min-microvolt to 750000.
Whent thor protocol is used, board_usb_init() should be tried to set to
750000. But it was returned -EINVAL, because '750000' too lower than
2850000. (thor command doesn't work fine because of this problem.)
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Trats has the i2c gpio for fuel-gaugge.
This patch s for preparing to use the fuel-gauge.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
These codes are unnecessary, because max8997 should be initialized with
dt-file.
Remove max8997_init() function.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Enable the CONFIG_DM_PMIC and PMIC_MAX8997.
Also use the CONFIG_SYS_I2C_S3C24X0 for using I2C.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Introduce CONFIG_TEGRA124_MMC_DISABLE_EXT_LOOPBACK to disable the external clock
loopback and use the internal one on SDMMC3 as per the SDMMC_VENDOR_MISC_CNTRL_0
register's SDMMC_SPARE1 bits being set to 0xfffd according to the TRM.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This patch adds board support for the Toradex Apalis TK1 a computer on
module which can be used on different carrier boards.
The module consists of a Tegra TK1 SoC, a PMIC solution, 2 GB of DDR3L
RAM, a bunch of level shifters, an eMMC, a TMP451 temperature sensor
chip, an I210 gigabit Ethernet controller and a SGTL5000 audio codec.
Furthermore, there is a Kinetis MK20DN512 companion micro controller for
analogue, CAN and resistive touch functionality.
For the sake of ease of use we do not distinguish between different
carrier boards for now as the base module features are deemed
sufficient enough for regular booting.
The following functionality is working so far:
- eMMC boot, environment storage and Toradex factory config block
- Gigabit Ethernet
- MMC/SD cards (both MMC1 as well as SD1 slot)
- USB client/host (dual role OTG port as client e.g. for DFU/UMS or host,
other two ports as host)
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Even though we expect only master core to execute U-Boot code
let's make sure even if for some reason slave cores attempt to
execute U-Boot in parallel with master they get halted very early.
If platform wants it may kick-start slave cores before passing control
to say Linux kernel or any other application that want to see all cores
of SMP SoC up and running.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
In axs103 v1.1 procedure to kick-start slave cores has changed quite a bit
compared t previous implementation.
In particular:
* We used to have a generic START bit for all cores selected by CORE_SEL
mask. But now we don't touch CORE_SEL at all because we have a dedicated
START bit for each core:
bit 0: Core 0 (master)
bit 1: Core 1 (slave)
* Now there's no need to select "manual" mode of core start
Additional challenge for us is how to tell which axs103 firmware we're
dealing with. For now we'll rely on ARC core version which was bumped
from 2.1c to 3.0.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
* Rely on default pulse polarity value
* Don't mess with "multicore" value as it doesn't affect execution
In essence we now do a bare minimal stuff:
1) Select HS38x2_1 with CORE_SEL=1 bits
2) Select "manual" core start (via CREG) with START_MODE=0
3) Generate cpu_start pulse with START=1
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
This is a preparation work for the support of CONFIG_BLK.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
For consistency, use an accessor to access the private data. Also for the
same reason, rename all priv_data to priv.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The Marvell PHY support is needed espescially for the A7040-DB with the
SGMII port (port 2). As without the marvell PHY driver configuration
for SGMII, ethernet won't work.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The default configuration for the COMPHY-0 port should be 1G, as its
used as 1G SGMII connection. This change is necessary to get the
MAC2 port (SGMII) working on this DB.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
As pointed out by Stefan Chulski, this variable is unused and should be
removed.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Testing shows, that PHY polling needs to be enabled on Armada 7k/8k.
Otherwise ethernet transfers will not work correctly. PHY polling
is enabled per default after reset, so we do not need to specifically
enable it, but this makes it clearer.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds the GoP (Group of Ports) and NetC (Net Complex) setup to
the Marvell mvpp2 ethernet driver for the missing port 0. This code is
mostly copied from the Marvell U-Boot version and was written by Stefan
Chulski. Please note that only SFI support have been added, as this
is the only interface that this code has been tested with. XAUI and
RXAUI support might follow at a later stage.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds the GoP (Group of Ports) and NetC (Net Complex) setup to
the Marvell mvpp2 ethernet driver. This code is mostly copied from the
Marvell U-Boot version and was written by Stefan Chulski. Please
note that only RGMII and SGMII support have been added, as these are
the only interfaces that this code has been tested with.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Read the "phy-speed" DT property to differentiate between 1 and 2.5GB
SGMII operations. Please note that its unclear right now, if this
DT property will be accepted in mainline Linux. If not, we need to
revisit this code and change it to use the accepted property.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch does a bit of restructuring of the probe / init functions,
mainly to allow earlier register access as it is needed for the upcoming
GoP (Group of Ports) and NetC (Net Complex) code.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds the new PHY interface modes XAUI, RXAUI and SFI that will
be used by the PPv2.2 support in the Marvell mvpp2 ethernet driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds the PPv2.2 specific FIFO configuration to the mvpp2
driver. The RX FIFO packet data size is changed to the recommended
FIFO sizes. The TX FIFO configuration is newly added.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Currently, the naming of the ethernet ports is not handled correctly in
the multi-CP (Communication Processor) case. On Armada 8k, the slave-CP
also instantiates an ethernet controller with the same device ID's.
This patch now takes this into account and adds the required base-id
so that the slave-CP ethernet devices will be named "mvpp2-3 ...".
This patch also updates my Copyright notice to include 2017 as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefan Chulski <stefanc@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Since we've now integrated the A7k/8k support in the mvpp2 ethernet
driver, lets enable the support for both Marvell developments boards.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This commit adds the description of the PPv2.2 hardware block for the
Marvell Armada 7K and Armada 8K processors, and their corresponding Armada
7040 and 8040 Development boards.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Since Armada 7K/8K is also equipped with a newer version of the MVPP2
ethernet controller, lets enable compilation of this driver for these
platforms.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This fixes problems noticed with the PPv2.2 A7k/8k port, when not all
elements of the descriptors had been cleared before use.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch moves the base_probe function mvpp2_base_probe() from the
MISC driver to the ETH driver. When integrated in the MISC driver,
probe is called too early before the U-Boot ethernet infrastructure
(especially the MDIO / PHY interface) has been initialized. Resulting
in errors in mdio_register().
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In U-Boot the MDIO / SMI support is integrated in the mvpp2 driver,
currently only supporting the 32bit platforms (Armada 37x). This patch
now adds the A7k/8k PPv2.2 MDIO support to that the phy / mii IF
can be used as well on these platforms.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Now that the mvpp2 driver has been modified to accommodate the support
for PPv2.2, we can finally advertise this support by adding the
appropriate compatible string.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In PPv2.1, we have a maximum of 8 RXQs per port, with a default of 4
RXQs per port, and we were assigning RXQs 0->3 to the first port, 4->7
to the second port, 8->11 to the third port, etc.
In PPv2.2, we have a maximum of 32 RXQs per port, and we must allocate
RXQs from the range of 32 RXQs available for each port. So port 0 must
use RXQs in the range 0->31, port 1 in the range 32->63, etc.
This commit adapts the mvpp2 to this difference between PPv2.1 and
PPv2.2:
- The constant definition MVPP2_MAX_RXQ is replaced by a new field
'max_port_rxqs' in 'struct mvpp2', which stores the maximum number of
RXQs per port. This field is initialized during ->probe() depending
on the IP version.
- MVPP2_RXQ_TOTAL_NUM is removed, and instead we calculate the total
number of RXQs by multiplying the number of ports by the maximum of
RXQs per port. This was anyway used in only one place.
- In mvpp2_port_probe(), the calculation of port->first_rxq is adjusted
to cope with the different allocation strategy between PPv2.1 and
PPv2.2. Due to this change, the 'next_first_rxq' argument of this
function is no longer needed and is removed.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This commit adjusts how the MVPP2_ISR_RXQ_GROUP_REG register is
configured, since it changed between PPv2.1 and PPv2.2.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The PPv2.2 unit is connected to an AXI bus on Armada 7K/8K, so this
commit adds the necessary initialization of the AXI bridge.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This commit handles a few miscellaneous differences between PPv2.1 and
PPv2.2 in different areas, where code done for PPv2.1 doesn't apply for
PPv2.2 or needs to be adjusted (getting the MAC address, disabling PHY
polling, etc.).
Changed by Stefan for U-Boot:
Since mvpp2_port_power_up() has multiple callers in U-Boot, the U-Boot
version of this patch does not remove this function but simply adds the
check for MVPP21 before the mvpp2_port_fc_adv_enable() call.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This commit adjusts the mvpp2 driver register mapping and access logic
to support PPv2.2, to handle a number of differences.
Due to how the registers are laid out in memory, the Device Tree binding
for the "reg" property is different:
- On PPv2.1, we had a first area for the common registers, and then one
area per port.
- On PPv2.2, we have a first area for the common registers, and a
second area for all the per-ports registers.
In addition, on PPv2.2, the area for the common registers is split into
so-called "address spaces" of 64 KB each. They allow to access the same
registers, but from different CPUs. Hence the introduction of cpu_base[]
in 'struct mvpp2', and the modification of the mvpp2_write() and
mvpp2_read() register accessors. For PPv2.1, the compatibility is
preserved by using an "address space" size of 0.
Changed by Stefan for U-Boot:
Since we don't support multiple CPUs in U-Boot, I've removed all the
code, macros and variables introduced in the Linux patch version for this.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In PPv2.2, the MVPP2_RXQ_DESC_ADDR_REG and MVPP2_TXQ_DESC_ADDR_REG
registers have a slightly different layout, because they need to contain
a 64-bit address for the RX and TX descriptor arrays. This commit
adjusts those functions accordingly.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This commit modifies the mvpp2_defaults_set() function to not do the
loopback and FIFO threshold initialization, which are not needed for
PPv2.2.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The MVPP2_RXQ_CONFIG_REG register has a slightly different layout
between PPv2.1 and PPv2.2, so this commit adapts the functions modifying
this register to accommodate for both the PPv2.1 and PPv2.2 cases.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This commit adjusts the allocation and freeing of BM pools to support
PPv2.2. This involves:
- Checking that the number of buffer pointers is a multiple of 16, as
required by the hardware.
- Adjusting the size of the DMA coherent area allocated for buffer
pointers. Indeed, PPv2.2 needs space for 2 pointers of 64-bits per
buffer, as opposed to 2 pointers of 32-bits per buffer in
PPv2.1. The size in bytes is now stored in a new field of the
mvpp2_bm_pool structure.
- On PPv2.2, getting the physical and virtual address of each buffer
requires reading the MVPP2_BM_ADDR_HIGH_ALLOC to get the high order
bits of those addresses. A new utility function
mvpp2_bm_bufs_get_addrs() is introduced to handle this.
- On PPv2.2, releasing a buffer requires writing the high order 32 bits
of the physical address to MVPP2_BM_PHY_VIRT_HIGH_RLS_REG. We no
longer need to write the virtual address to MVPP2_BM_VIRT_RLS_REG.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This commit adds the definition of the PPv2.2 HW descriptors, adjusts
the mvpp2_tx_desc and mvpp2_rx_desc structures accordingly, and adapts
the accessors to work on both PPv2.1 and PPv2.2.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Since the format of the HW descriptors is different between PPv2.1 and
PPv2.2, this commit introduces an intermediate union, with for now
only the PPv2.1 descriptors. The bulk of the driver code only
manipulates opaque mvpp2_tx_desc and mvpp2_rx_desc pointers, and the
descriptors can only be accessed and modified through the accessor
functions. A follow-up commit will add the descriptor definitions for
PPv2.2.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In preparation to the introduction for the support of PPv2.2 in the
mvpp2 driver, this commit adds a hw_version field to the struct
mvpp2, and uses the .data field of the DT match table to fill it in.
Having the MVPP21 and MVPP22 definitions available will allow to start
adding the necessary conditional code to support PPv2.2.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The PPv2.2 IP has a different TX and RX descriptor layout compared to
PPv2.1. In order to prepare for the introduction of PPv2.2 support in
mvpp2, this commit adds accessors for the different fields of the TX
and RX descriptors, and changes the code to use them.
For now, the mvpp2_port argument passed to the accessors is not used,
but it will be used in follow-up to update the descriptor according to
the version of the IP being used.
Apart from the mechanical changes to use the newly introduced
accessors, a few other changes, needed to use the accessors, are made:
- The mvpp2_txq_inc_put() function now takes a mvpp2_port as first
argument, as it is needed to use the accessors.
- Similarly, the mvpp2_bm_cookie_build() gains a mvpp2_port first
argument, for the same reason.
- In mvpp2_rx_error(), instead of accessing the RX descriptor in each
case of the switch, we introduce a local variable to store the
packet size.
- Similarly, in mvpp2_buff_hdr_rx(), we introduce a local "cookie"
variable to store the RX descriptor cookie, rather than accessing
it from the descriptor each time.
- In mvpp2_tx_frag_process() and mvpp2_tx() instead of accessing the
packet size from the TX descriptor, we use the actual value
available in the function, which is used to set the TX descriptor
packet size a few lines before.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
As indicated by Russell King, the mvpp2 driver currently uses a lot
"phys" or "phys_addr" to store what really is a DMA address. This commit
clarifies this by using "dma" or "dma_addr" where appropriate.
This is especially important as we are going to introduce more changes
where the distinction between physical address and DMA address will be
key.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Some more U-Boot specific 64bit support changes, mostly changing u32
to unsigned long.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The mvpp2 is going to be extended to support the Marvell Armada 7K/8K
platform, which is ARM64. As a preparation to this work, this commit
enables building the mvpp2 driver on ARM64, by:
- Adjusting the Kconfig dependency
- Fixing the types used in the driver so that they are 32/64-bits
compliant. We use dma_addr_t for DMA addresses, and unsigned long
for virtual addresses.
It is worth mentioning that after this commit, the driver is for now
still only used on 32-bits platforms, and will only work on 32-bits
platforms.
Changed by Stefan for U-Boot:
Removed the Kconfig change as it does not apply to U-Boot this way.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Some of the MVPP2_PRS_RI_* definitions use the ~(value) syntax, which
doesn't compile nicely on 64-bit. Moreover, those definitions are in
fact unneeded, since they are always used in combination with a bit
mask that ensures only the appropriate bits are modified.
Therefore, such definitions should just be set to 0x0. In addition, as
suggested by Russell King, we change the _MASK definitions to also use
the BIT() macro so that it is clear they are related to the values
defined afterwards.
For example:
#define MVPP2_PRS_RI_L2_CAST_MASK 0x600
#define MVPP2_PRS_RI_L2_UCAST ~(BIT(9) | BIT(10))
#define MVPP2_PRS_RI_L2_MCAST BIT(9)
#define MVPP2_PRS_RI_L2_BCAST BIT(10)
becomes
#define MVPP2_PRS_RI_L2_CAST_MASK (BIT(9) | BIT(10))
#define MVPP2_PRS_RI_L2_UCAST 0x0
#define MVPP2_PRS_RI_L2_MCAST BIT(9)
#define MVPP2_PRS_RI_L2_BCAST BIT(10)
Because the values (MVPP2_PRS_RI_L2_UCAST, MVPP2_PRS_RI_L2_MCAST and
MVPP2_PRS_RI_L2_BCAST) are always applied with
MVPP2_PRS_RI_L2_CAST_MASK, and therefore there is no need for
MVPP2_PRS_RI_L2_UCAST to be defined as ~(BIT(9) | BIT(10)).
It fixes the following warnings when building the driver on a 64-bit
platform (which is not possible as of this commit, but will be enabled
in a follow-up commit):
drivers/net/ethernet/marvell/mvpp2.c: In function ‘mvpp2_prs_mac_promisc_set’:
drivers/net/ethernet/marvell/mvpp2.c:524:33: warning: large integer implicitly truncated to unsigned type [-Woverflow]
#define MVPP2_PRS_RI_L2_UCAST ~(BIT(9) | BIT(10))
^
drivers/net/ethernet/marvell/mvpp2.c:1459:33: note: in expansion of macro ‘MVPP2_PRS_RI_L2_UCAST’
mvpp2_prs_sram_ri_update(&pe, MVPP2_PRS_RI_L2_UCAST,
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The mvpp2_bm_bufs_add() currently creates a fake cookie by calling
mvpp2_bm_cookie_pool_set(), just to be able to call
mvpp2_pool_refill(). But all what mvpp2_pool_refill() does is extract
the pool ID from the cookie, and call mvpp2_bm_pool_put() with this ID.
Instead of doing this convoluted thing, just call mvpp2_bm_pool_put()
directly, since we have the BM pool ID.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
check_cache_range() warns that the top boundaries are not properly
aligned when flushing or invalidating the buffers and make these
operations fail.
This gets rid of the warnings:
CACHE: Misaligned operation at range ...
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The macro GENMASK_ULL needs the BITS_PER_LONG_LONG macro which is
defined in the bitsperlong.h header. Lets include this header as
the upcoming A7k/8k support in the Marvell mvpp2 ethernet driver
uses this macro.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
This commit replaces legacy timer code with usage of arc timer
driver.
It removes arch/arc/lib/time.c file and selects CONFIG_CLK,
CONFIG_TIMER and CONFIG_ARC_TIMER options for all ARC boards by default.
Therefore we remove CONFIG_CLK option from less common axs101 and
axs103 defconfigs.
Also it removes legacy CONFIG_SYS_TIMER_RATE config symbol from
axs10x.h, tb100.h and nsim.h configs files as it is no longer required.
Signed-off-by: Vlad Zakharov <vzakhar@synopsys.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We want to use the same device tree blobs in both Linux and U-Boot for
ARC boards.
Earlier device tree sources in U-Boot were very simplified and hadn't been
updated for quite a long period of time.
So this commit is the first step on the road to unified device tree blobs.
First of all we re-organize device tree sources for AXS10X boards.
As AXS101 and AXS103 boards consist of AXS10X motherboard and AXC001 and
AXC003 cpu tiles respectively we add corresponding device tree source
files: axs10x_mb.dtsi for motherboard, axc001.dtsi and axc003.dtsi for
cpu tiles and axs101.dts and axs103.dts to represent actual boards.
Also we delete axs10x.dts as it is no longer used.
One more important change - we add timer device to ARC skeleton device
tree sources as both ARC700 and ARCHS cores contain such timer.
We add core_clk nodes to abilis_tb100, nsim, axc001 and axc003 device tree
sources as it is referenced via phandle from timer node in common
skeleton.dtsi file.
Signed-off-by: Vlad Zakharov <vzakhar@synopsys.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit introduces timer driver for ARC.
ARC timers are configured via ARC AUX registers so we use special
functions to access timer control registers.
This driver allows utilization of either timer0 or timer1
depending on which one is available in real hardware. Essentially
only existing timers should be mentioned in board's Device Tree
description.
Signed-off-by: Vlad Zakharov <vzakhar@synopsys.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The gdsys ControlCenter Digital board is based on a Marvell Armada 38x
SOC.
It boots from SPI-Flash but can be configured to boot from SD-card for
factory programming and testing.
On board peripherals include:
- 2 x GbE
- Xilinx Kintex-7 FPGA connected via PCIe
- mSATA
- USB3 host
- Atmel TPM
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Certain boards come in different variations by way of utilizing daughter
boards, for example. These boards might contain additional chips, which
are added to the main board's busses, e.g. I2C.
The device tree support for such boards would either, quite naturally,
employ the overlay mechanism to add such chips to the tree, or would use
one large default device tree, and delete the devices that are actually
not present.
Regardless of approach, even on the U-Boot level, a modification of the
device tree is a prerequisite to have such modular families of boards
supported properly.
Therefore, we add an option to make the U-Boot device tree (the actual
copy later used by the driver model) writeable, and add a callback
method that allows boards to modify the device tree at an early stage,
at which, hopefully, also the application of device tree overlays will
be possible.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
This board specific command tests for the presence of a specified PCIe
device (via vendor-ID and device-ID). If the device is not detected,
this will get printed. If the device is detected, the board will get
resetted so that an easy loop test can be done. The board will reboot
until the PCIe device is not detected.
Signed-off-by: Stefan Roese <sr@denx.de>
Define a board-specific detection pulse-width array for the SerDes PCIe
interfaces. If not defined in the board code, the default of currently 2
is used. Values from 0...3 are possible (2 bits).
In this case of the theadorable board, PEX interface 0 needs a value
of 0 for the detection pulse width so that the PCIe device (Atheros
WLAN PCIe device) is consistantly detected.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Adam Shobash <adams@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Tests have shown that on some boards the default width of the
configuration pulse for the PEX link detection might lead to
non-established PCIe links (link down). Especially under certain
conditions (higher temperature) and with specific PCIe devices
(in the case on the theadorable board its a Atheros PCIe WLAN
device). To enable a board-specific detection pulse width this weak
array "serdes_pex_pulse_width[4]" is introduced which can be
overwritten if needed by a board-specific version. If the board
code does not provide a non-weak version of this variable, the
default value will be used. So nothing is changed from the
current setup on the supported board.
Many thanks to Adam from Marvell for all his insights here and
his suggestion about testing with a changed detection pulse width.
Signed-off-by: Stefan Roese <sr@denx.de>
Suggested-by: Adam Shobash <adams@marvell.com>
Cc: Adam Shobash <adams@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Remove DM_I2C_COMPAT from the board configurations for
Armada 37xx platform boards for supressing the buid tim
warning.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Bypass XHCI and AHCi board configuration flow on ESPRESSOBin
community board.
The community board does not have i2c expander and USB VBUS
is always on, so the scan for AHCi and USB devices can be
faster without unneded configurations.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add initial default configuration for Marvell ESPRESSOBin
community board based on Aramda-3720 SoC
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Initial DTS file for Marvell ESPRESSOBin comunity board
based on Armada-3720 SoC.
The Marvell ESPRESSOBin is a tiny board made by Globalscale
and available on KickStarter site. It has dual core Armv8
Marvell SoC (Armada-3720) with 512MB/1GB/2GB DDR3 RAM,
mini-PCIe 2.0 slot, single SATA-3 port, USB 2.0 and USB 3.0
interfaces, Gigabit Ethernet switch with 3 ports, micro-SD
socket and two 46-pin GPIO connectors.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Implement the board-specific network init function for
ESPRESSOBin community board, setting the on-board Topaz
switch port to forward mode and allow network connection
through any of the available Etherenet ports.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add support for fixed link to NETA driver.
This feature requreed for proper support of SFP modules
and onboard connected devices like Ethernet switches
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Terry Zhou <bjzhou@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add ability to use board-specific initialization flow
to NETA driver (for instance Ethernet switch bring-up)
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Fix the default pin control values in a board-specific
function on early board init stage.
This fix allows the NETA driver to work in RGMII
mode until the full-featured pin control driver gets
introduced.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Modify the file names and deifinitions relater to Marvell
db-77f3720 board support. Convert these names to more generic
armada-37xx platform for future addition of more boards
based on the same SoC family.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The USB device should linked to VBUS regulator through "vbus-supply"
DTS property.
This patch adds handling for "vbus-supply" property inside the USB
device entry for turning on the VBUS regulator upon the host adapter probe.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Added A8040 dts file for community board MACCHIATIBin.
The patch includes the following features:
AP - Serial console (connected to onboard FTDI usb to serial)
CP0 - PCIe x4, SATA, I2C and 10G KR
(connected to Marvell 3310 10G copper / SFP+ phy)
CP1 - Boot SPI, USB3 host, 2xSATA, 10G KR
(connected to Marvell 3310 10G copper / SFP+ phy),
SGMII connected to onboard 1512 1Gbps copper phy,
and additional SGMII connected to SFP
(default 1Gbps can be configured to 2.5Gbps).
Network interface naming -
egiga0 - CP0 KR
egiga1 - CP1 KR
egiga2 - CP1 RJ45 1Gbps connector (recommended for TFTP boot)
egiga3 - CP1 SFP default 1Gbps and can be modified to 2.5Gbps
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Previously, dtoc could only process the top-level nodes which led to
device nodes in hierarchical trees to be ignored. E.g. the mmc0 node
in the following example would be ignored, as only the soc node was
processed:
/ {
soc {
mmc0 {
/* ... */
};
};
};
This introduces a recursive helper method ScanNode, which is used by
ScanTree to recursively parse the entire tree hierarchy.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We used to get the address of the optionnal ctrl_mod_mmap register as the
third memory range of the "reg" property. the linux driver moved to use a
syscon instead. In order to keep the DTS as close as possible to that of
linux, we move to using a syscon as well.
If SYSCON is not supported, the driver reverts to the old way of getting
the address from the 3rd memory range
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
In the DTS, the addresses are defined relative to the parent bus. We need
to translate them to get the address as seen by the CPU core.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
commit 2f11cd9121 ("dm: core: Handle global_data moving in SPL")
handles relocation of GD in SPL if spl_init() is called before
board_init_r(). So, uclass_root.next need not be initialized always
and accessing uclass_root.next->prev gives an abort. Update the
uclass_root only if it is available.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The Xenon SDHCI driver just missed the integration of this patch:
git ID 6d0e34bf
mmc: sdhci: Distinguish between base clock and maximum peripheral frequency
With this patch applied, the SDHCI subsystem complains now with this warning
while probing:
sdhci_setup_cfg: Hardware doesn't specify base clock frequency
This patch fixes this issue, by providing the missing host->max_clk
variable to the SDHCI subsystem.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Hu Ziji <huziji@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
It's redundant to send cmd13 after cmd9 whose response is not R1b. The
card devices will not be busy w/ cmd9.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
This patch adds Intel Tangier eMMC/SDHCI driver.
Intel Tangier SoC contains a hybrid of PCI and non-PCI devices. SDHCI
controller is one of the devices which are *not* on a PCI and, hence,
cannot be enumerated by standard PCI means. This driver, allows for
SDHCI controller on Tangier SoC to work in U-Boot.
Signed-off-by: Vincent Tinelli <vincent.tinelli@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We don't want pci_mmc to compile every time x86 compiles, only when
there's a platform that needs it. For that reason, we're adding a new
CONFIG_MMC_PCI which platforms can choose to enable.
Suggested-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This patch fixup iommu-map property on pci node to have a valid
mapping of requester-id to stream-id. The requester-id to stream-id
mapping is based on PCI-LUT table initialization.
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Layerscape Chasis-2 also uses same PCIe controller as Chasis-3
and have similar PCI-Lut.
Signed-off-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS1012A is Chassis-2 type SOC and shares same streamid definition.
This patch adds using streamids for ls1012a
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS1046A is Chassis-2 type SOC and shares same streamid definition,
this patch adds using streamids for LS1046A.
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Layerscape Chassis-2 have PCIe device, some platform devices and
DPAA1 devices which will use stream-ids for iommu level isolation
as they are behind SMMU.
This patch defines the stream-ids for Chassis-2 devices. DPAA1 is
reserved for future use.
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS2080a, LS1088a and LS2088a SOCs are based on Chassis-3 and shared
same stream-id partitioning. This patch rewords the definition to
support all these SOCs.
Also have changes in description about iommu-map property updates
in PCI node.
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The stream ID allocation for Chasis 3.0 devices can be shared among
LS1088, LS2088 and LS2080.
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add nand_size() function to move the nand size print into initr_nand().
Remove nand size print from nand_init() to allow other function to call
nand_init() without printing nand size.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add initialization flag to avoid initializing NAND Flash multiple
times, otherwise it will calculate a wrong total size.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
USB requires 100MHz clock. On LS1012A, a dedicated 100MHz is provided
instead of SYSCLK (125MHz). Skipping checking SYSCLK for FDT fixup.
Signed-off-by: Yingxi Yu <yingxi.yu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Fix the offsets of MTD partitions on Nor flash on ls1043ardb,
ls1043aqds and ls1046aqds boards. Delete the rcw, uboot env and fman
partitions. Add user partitions for general usage.
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS2088A and its variants have different PCIe node than LS2080A.
The compatible string is updated accordingly.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The LS2088A series SoCs has different physical memory map address and
CCSR registers address against LS2080A series SoCs.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This i2c errata only applies to LS2080A and its variants, namely
LS2080A, LS2085A and LS2088A.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
SOC’s like LS1012A has only one chip select signal for QSPI flash.
Avoid scanning other flash.
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
SerDes information is not necessary to be present in RCWSR29 register.
It may vary from SoC to SoC.
So Avoid RCWSR28 register hard-coding.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
MAC number used per QSGMII is not fixed. It may wary from SoC to SoC.
So move QSGMII wriop_init_dpmac() to SoC file.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Erratum A009635 is valid only for LS2080A SoC and its
personality. Add SoC svr check.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
In EP mode, to enable accesses from the Root Complex, the
CONFIG_READY bit must be set, otherwise any config attempts
from the Root Complex will be returned with config retry
status (CRS).
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
For validating images from uboot (Such as Kernel Image), either keys
from SoC fuses can be used or keys from a verified table of public
keys can be used. The latter feature is called IE Key Extension
Feature.
For Layerscape Chasis 3 based platforms, IE table is validated by
Bootrom and address of this table is written in scratch registers 13
and 14 via PBI commands.
Following are the steps describing usage of this feature:
1) Verify IE Table in ISBC phase using keys stored in fuses.
2) Install IE table. (To be used across verification of multiple
images stored in a static global structure.)
3) Use keys from IE table, to verify further images.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Moved the ifdef into ppa.h and removed the duplicated macros.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Moves sec_init to board_init rather than in misc_init function beacuse
PPA will be initialised in board_init function and for PPA validation
sec_init has to be done prior to PPA init.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add header address for PPA to be validated during ESBC phase for LS2080A
platform based on Layescape Chasis 3.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch allows using i2c commands (e.g. "i2c probe", "i2c md", etc)
without the need to first select the bus number with e.g. "i2c dev 0".
This is the "i2c" command behavior similar to the one from pre DM, where
by default bus 0 was immediately accessible.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This patch updates the way in which psc, sscl and ssch I2C parameters are
calculated to be in sync with v4.9 Linux kernel
SHA1: 69973b830859bc6529a7a0468ba0d80ee5117826
in the ./drivers/i2c/busses/i2c-omap.c
The previous method was causing several issues:
- The internal I2C frequency (after prescaler) was far above recommended
one (7 - 12 MHz [*]) - the current approach brings better noise suppression
(as stated in Linux commit: SHA1: 84bf2c868f3ca996e5bb)
- The values calculated (psc, sscl and ssch) were far from optimal, which
caused on the test platform (AM57xx) the I2C0 SCL signal low time (Fast
Mode) of ~1.0us (the standard requires > 1.3 us).
[*] for AM57xx TRM SPRUHZ6G, Table 24,7
"HS I2C Register Values for Maximum I2C Bit Rates in I2C F/S, I2C HS Modes"
Signed-off-by: Lukasz Majewski <lukma@denx.de>
v4.9 Linux release:
SHA1: 69973b830859bc6529a7a0468ba0d80ee5117826
in the ./drivers/i2c/busses/i2c-omap.c
recommends to use SCLH=5 and SCLL=7 values.
This patch sets them to default.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Normally, this would probably be done by adding devicetree aliases
to the main dtsi file for the lpc32xx and using bus->req_seq instead.
Since we want to have consistent i2c numbering, we cannot force the
bus->req_seq because. If for instance we have 3 buses numbered
from 0 to 2 with i2c0 enabled, i2c1 disabled and i2c2 enabled;
i2c2 can be selected using 'i2c dev 1' and 'i2c dev 2' commands
because a bus can be probed using req_seq or seq interchangeably.
Signed-off-by: Liam Beguin <lbeguin@tycoint.com>
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Since the lpc32xx i2c driver does not yet support the devicetree bindings,
this structure is also needed by the board file as the hardware description
is done there.
Signed-off-by: Liam Beguin <lbeguin@tycoint.com>
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
This is part of the prep work for the migration to the driver model.
It will enable the driver to support DM and non-DM configurations
using the same functions.
Signed-off-by: Liam Beguin <lbeguin@tycoint.com>
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
This is part of the prep work for the migration to the driver model.
Signed-off-by: Liam Beguin <lbeguin@tycoint.com>
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
This is part of the prep work for the migration to the driver model.
What used to be the probe function is now called probe_chip.
Signed-off-by: Liam Beguin <lbeguin@tycoint.com>
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
This patch adds a reset controller implementation for STMicroelectronics
STi family SoCs; it allows a group of related reset like controls found
in multiple system configuration registers to be represented by a single
controller device.
Driver code has been mainly extracted from kernel
drivers/reset/sti/reset-stih407.c
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
In the description of function pci_match_one_id(), there are some
problems on arguments list and return value description, so correct
them.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is sometimes convenient to know how many and/or which resources are
currently loaded into a TPG, e.g. to test is a flush operation succeeded.
Hence, we add a command that lists the resources of a given type currently
loaded into the TPM.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit 7690be35de ("lib: tpm: Add command to flush resources") added a command
to flush resources from a TPM.
However, a previous development version was accidentially used to generate the
patch, resulting in a non-functional command.
This patch fixes the flush command.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
If we want to load a key into a TPM, we need to know the designated parent
key's handle, so that the TPM is able to insert the key at the correct place in
the key hierarchy.
However, if we want to load a key whose designated parent key we also
previously loaded ourselves, we first need to memorize this parent key's handle
(since the handles for the key are chosen at random when they are inserted into
the TPM). If we are, however, unable to do so, for example if the parent key is
loaded into the TPM during production, and its child key during the actual
boot, we must find a different mechanism to identify the parent key.
To solve this problem, we add a function that allows U-Boot to load a key into
the TPM using their designated parent key's SHA1 hash, and the corresponding
auth data.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use CONFIG_IS_ENABLED() macro to check whether OF_TRANSLATE is enabled, so
that code block is compiled irrespective of SPL or U-Boot build
and fdt address translation is used.
Signed-off-by: Vignesh R <vigneshr@ti.com>
This patch adds support for having a "fixed-link" to some other MAC
(like some embedded switch-device).
For this purpose we introduce a new phy-driver, called "Fixed PHY".
Fixed PHY works only with CONFIG_DM_ETH enabled, since the fixed-link is
described with a subnode below ethernet interface.
Most ethernet drivers (unfortunately not all are following same scheme
for searching/attaching phys) are calling "phy_connect(...)" for getting
a phy-device.
At this point we link in, we search here for a subnode called "fixed-
link", once found we start phy_device_create(...) with the special phy-
id PHY_FIXED_ID (0xa5a55a5a).
During init the "Fixed PHY" driver has registered with this id and now
gets probed, during probe we get all the details about fixed-link out of
dts, later on the phy reports this values.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
The Raspberry Pi device tree files since Linux v4.9 have a "ethernet"
alias pointing to the on-board Ethernet device node. However,
U-Boot's fdt_fixup_ethernet() only looks at ethernet aliases ending
in digits.
As the spec doesn't mandate that aliases must end in numbers and there
have been much older uses of an "ethernet" aliases in the wild
(according to Tom Rini), change the code to accept "ethernet" as well.
Without this Linux isn't told of the MAC address provided by the
RPI firmware and the ethernet interface is always assigned a random MAC
address.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The network mask must be stored in network order when in a
'struct in_addr'.
This fix removes the "gatewayip needed but not set" message on the
console when using a link-local IP setup.
Signed-off-by: Alexandre Messier <amessier@tycoint.com>
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Apply the proper setting for the reserved bits in SetDes Test and System Mode Control register
to avoid the voltage peak issue while we do the IEEE PHY comformance test
Signed-off-by: Ken Lin <yungching0725@gmail.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Acked-by: Ian Ray <ian.ray@ge.com>
Add the delay (10ms) to ensure the clock is stable and to meet the clock-to-reset(1ms) requirement recommended in the AR8033 datasheet
Signed-off-by: Ken Lin <yungching0725@gmail.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Acked-by: Ian Ray <ian.ray@ge.com>
This patch enables the I2C EEPROM to be probed for a MAC address on the
OLinuXino Lime1 and Lime2 boards. Other boards surely qualify as well
but were not tested yet.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Currently the mac address is programmed directly in _sunxi_emac_eth_init
making it a one time inflexible operation. By moving it into a separate
function, we can now use this more flexibly.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This replaces legacy arch/arc/lib/timer.c implementation and allows us
to describe ARC Timers in Device Tree. Among other things that way we
may properly inherit Timer's clock from CPU's clock s they really run
synchronously.
This commit replaces legacy timer code with usage of arc timer
driver.
It removes arch/arc/lib/time.c file and selects CONFIG_CLK,
CONFIG_TIMER and CONFIG_ARC_TIMER options for all ARC boards by default.
Therefore we remove CONFIG_CLK option from less common axs101 and
axs103 defconfigs.
Also it removes legacy CONFIG_SYS_TIMER_RATE config symbol from
axs10x.h, tb100.h and nsim.h configs files as it is no longer required.
Signed-off-by: Vlad Zakharov <vzakhar@synopsys.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We want to use the same device tree blobs in both Linux and U-Boot for
ARC boards.
Earlier device tree sources in U-Boot were very simplified and hadn't been
updated for quite a long period of time.
So this commit is the first step on the road to unified device tree blobs.
First of all we re-organize device tree sources for AXS10X boards.
As AXS101 and AXS103 boards consist of AXS10X motherboard and AXC001 and
AXC003 cpu tiles respectively we add corresponding device tree source
files: axs10x_mb.dtsi for motherboard, axc001.dtsi and axc003.dtsi for
cpu tiles and axs101.dts and axs103.dts to represent actual boards.
Also we delete axs10x.dts as it is no longer used.
One more important change - we add timer device to ARC skeleton device
tree sources as both ARC700 and ARCHS cores contain such timer.
We add core_clk nodes to abilis_tb100, nsim, axc001 and axc003 device tree
sources as it is referenced via phandle from timer node in common
skeleton.dtsi file.
Signed-off-by: Vlad Zakharov <vzakhar@synopsys.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit introduces timer driver for ARC.
ARC timers are configured via ARC AUX registers so we use special
functions to access timer control registers.
This driver allows utilization of either timer0 or timer1
depending on which one is available in real hardware. Essentially
only existing timers should be mentioned in board's Device Tree
description.
Signed-off-by: Vlad Zakharov <vzakhar@synopsys.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The gdsys ControlCenter Digital board is based on a Marvell Armada 38x
SOC.
It boots from SPI-Flash but can be configured to boot from SD-card for
factory programming and testing.
On board peripherals include:
- 2 x GbE
- Xilinx Kintex-7 FPGA connected via PCIe
- mSATA
- USB3 host
- Atmel TPM
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Certain boards come in different variations by way of utilizing daughter
boards, for example. These boards might contain additional chips, which
are added to the main board's busses, e.g. I2C.
The device tree support for such boards would either, quite naturally,
employ the overlay mechanism to add such chips to the tree, or would use
one large default device tree, and delete the devices that are actually
not present.
Regardless of approach, even on the U-Boot level, a modification of the
device tree is a prerequisite to have such modular families of boards
supported properly.
Therefore, we add an option to make the U-Boot device tree (the actual
copy later used by the driver model) writeable, and add a callback
method that allows boards to modify the device tree at an early stage,
at which, hopefully, also the application of device tree overlays will
be possible.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
This board specific command tests for the presence of a specified PCIe
device (via vendor-ID and device-ID). If the device is not detected,
this will get printed. If the device is detected, the board will get
resetted so that an easy loop test can be done. The board will reboot
until the PCIe device is not detected.
Signed-off-by: Stefan Roese <sr@denx.de>
Define a board-specific detection pulse-width array for the SerDes PCIe
interfaces. If not defined in the board code, the default of currently 2
is used. Values from 0...3 are possible (2 bits).
In this case of the theadorable board, PEX interface 0 needs a value
of 0 for the detection pulse width so that the PCIe device (Atheros
WLAN PCIe device) is consistantly detected.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Adam Shobash <adams@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Tests have shown that on some boards the default width of the
configuration pulse for the PEX link detection might lead to
non-established PCIe links (link down). Especially under certain
conditions (higher temperature) and with specific PCIe devices
(in the case on the theadorable board its a Atheros PCIe WLAN
device). To enable a board-specific detection pulse width this weak
array "serdes_pex_pulse_width[4]" is introduced which can be
overwritten if needed by a board-specific version. If the board
code does not provide a non-weak version of this variable, the
default value will be used. So nothing is changed from the
current setup on the supported board.
Many thanks to Adam from Marvell for all his insights here and
his suggestion about testing with a changed detection pulse width.
Signed-off-by: Stefan Roese <sr@denx.de>
Suggested-by: Adam Shobash <adams@marvell.com>
Cc: Adam Shobash <adams@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Remove DM_I2C_COMPAT from the board configurations for
Armada 37xx platform boards for supressing the buid tim
warning.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Bypass XHCI and AHCi board configuration flow on ESPRESSOBin
community board.
The community board does not have i2c expander and USB VBUS
is always on, so the scan for AHCi and USB devices can be
faster without unneded configurations.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add initial default configuration for Marvell ESPRESSOBin
community board based on Aramda-3720 SoC
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Initial DTS file for Marvell ESPRESSOBin comunity board
based on Armada-3720 SoC.
The Marvell ESPRESSOBin is a tiny board made by Globalscale
and available on KickStarter site. It has dual core Armv8
Marvell SoC (Armada-3720) with 512MB/1GB/2GB DDR3 RAM,
mini-PCIe 2.0 slot, single SATA-3 port, USB 2.0 and USB 3.0
interfaces, Gigabit Ethernet switch with 3 ports, micro-SD
socket and two 46-pin GPIO connectors.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Implement the board-specific network init function for
ESPRESSOBin community board, setting the on-board Topaz
switch port to forward mode and allow network connection
through any of the available Etherenet ports.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add support for fixed link to NETA driver.
This feature requreed for proper support of SFP modules
and onboard connected devices like Ethernet switches
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Terry Zhou <bjzhou@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add ability to use board-specific initialization flow
to NETA driver (for instance Ethernet switch bring-up)
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Fix the default pin control values in a board-specific
function on early board init stage.
This fix allows the NETA driver to work in RGMII
mode until the full-featured pin control driver gets
introduced.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Modify the file names and deifinitions relater to Marvell
db-77f3720 board support. Convert these names to more generic
armada-37xx platform for future addition of more boards
based on the same SoC family.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The USB device should linked to VBUS regulator through "vbus-supply"
DTS property.
This patch adds handling for "vbus-supply" property inside the USB
device entry for turning on the VBUS regulator upon the host adapter probe.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Added A8040 dts file for community board MACCHIATIBin.
The patch includes the following features:
AP - Serial console (connected to onboard FTDI usb to serial)
CP0 - PCIe x4, SATA, I2C and 10G KR
(connected to Marvell 3310 10G copper / SFP+ phy)
CP1 - Boot SPI, USB3 host, 2xSATA, 10G KR
(connected to Marvell 3310 10G copper / SFP+ phy),
SGMII connected to onboard 1512 1Gbps copper phy,
and additional SGMII connected to SFP
(default 1Gbps can be configured to 2.5Gbps).
Network interface naming -
egiga0 - CP0 KR
egiga1 - CP1 KR
egiga2 - CP1 RJ45 1Gbps connector (recommended for TFTP boot)
egiga3 - CP1 SFP default 1Gbps and can be modified to 2.5Gbps
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Previously, dtoc could only process the top-level nodes which led to
device nodes in hierarchical trees to be ignored. E.g. the mmc0 node
in the following example would be ignored, as only the soc node was
processed:
/ {
soc {
mmc0 {
/* ... */
};
};
};
This introduces a recursive helper method ScanNode, which is used by
ScanTree to recursively parse the entire tree hierarchy.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We used to get the address of the optionnal ctrl_mod_mmap register as the
third memory range of the "reg" property. the linux driver moved to use a
syscon instead. In order to keep the DTS as close as possible to that of
linux, we move to using a syscon as well.
If SYSCON is not supported, the driver reverts to the old way of getting
the address from the 3rd memory range
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
In the DTS, the addresses are defined relative to the parent bus. We need
to translate them to get the address as seen by the CPU core.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
commit 2f11cd9121 ("dm: core: Handle global_data moving in SPL")
handles relocation of GD in SPL if spl_init() is called before
board_init_r(). So, uclass_root.next need not be initialized always
and accessing uclass_root.next->prev gives an abort. Update the
uclass_root only if it is available.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The Xenon SDHCI driver just missed the integration of this patch:
git ID 6d0e34bf
mmc: sdhci: Distinguish between base clock and maximum peripheral frequency
With this patch applied, the SDHCI subsystem complains now with this warning
while probing:
sdhci_setup_cfg: Hardware doesn't specify base clock frequency
This patch fixes this issue, by providing the missing host->max_clk
variable to the SDHCI subsystem.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Hu Ziji <huziji@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
It's redundant to send cmd13 after cmd9 whose response is not R1b. The
card devices will not be busy w/ cmd9.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
This patch adds Intel Tangier eMMC/SDHCI driver.
Intel Tangier SoC contains a hybrid of PCI and non-PCI devices. SDHCI
controller is one of the devices which are *not* on a PCI and, hence,
cannot be enumerated by standard PCI means. This driver, allows for
SDHCI controller on Tangier SoC to work in U-Boot.
Signed-off-by: Vincent Tinelli <vincent.tinelli@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We don't want pci_mmc to compile every time x86 compiles, only when
there's a platform that needs it. For that reason, we're adding a new
CONFIG_MMC_PCI which platforms can choose to enable.
Suggested-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Enable DM_I2C/SPI/ETH for all AM43XX based boards.
Enable it using imply keyword so that a user can
disable this when not needed.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add u-boot specific dtsi for am43xx-gp-evm so
that it will be used for SPL.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add u-boot specific dtsi so that this will be
included automatically while building dts.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
To make SPL_OF_CONTROL work on OMAP2+ SoCs, _image_binary_end must be
defined in the linker script along with CONFIG_SPL_SEPARATE_BSS.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Calls to IS_ENABLED() on a non-y/n option will always be false, even
when set. We can correct this by adding a new bool value that is set
based on the conditions required for SPL_STACK_R_MALLOC_SIMPLE_LEN to be
set instead.
Fixes: 340f418acd ("spl: Add spl_early_init()")
Reported-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
---
Changes in v2:
- Fix thinko pointed out by Lokesh
Add support for the Broadcom Northstar2 SoC and SVK (bcm958712k). The
BCM5871X is a series of quad-core 64-bit 2GHz ARMv8 Cortex-A57
processors targeting a broad range of networking applications.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
When building u-boot tools in cross-build environment CFLAGS environment
variable set up for target is taken into an account when building code
for host. Make it empty on invocation of python.
This fixes the following build errors when cross-compiling for xtensa:
cc1: error: unrecognized command line option "-mlongcalls"
cc1: error: unrecognized command line option "-mauto-litpools"
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The CAAM in IMX parts doesn't support public key hardware acceleration
(PKHA), so don't use RSA_FREESCALE_EXP. If you try to use it on IMX
(assuming you have the clocks enabled first) you will get back an
"Invalid KEY Command" error since PKHA isn't a valid key destination for
these parts.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Currently, AM43xx just re-uses the version strings from AM33xx which is
wrong; the actual values for AM43xx are different. Fix this by adding
a separate version string array for AM43xx and use this instead.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
* Add note that execution needs Python development package installed
* Standardize on upper case "FIT", "FDT" as necessary for clarity
* Fix "tempoerary", "linex" typos
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
This adds documentation on the u-boot,efi-partition-entries-offset
property (which overrides CONFIG_EFI_PARTITION_ENTRIES_OFF, if
present).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This moves the description of the /config node from README.fdt-control
into a separate file doc/device-tree-bindings/config.txt.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some architectures require their SPL loader at a fixed address within
the first 16KB of the disk. To avoid an overlap with the partition
entries of the EFI partition table, the first safe offset (in bytes,
from the start of the device) for the entries can be set through
CONFIG_EFI_PARTITION_ENTRIES_OFF (via Kconfig)
When formatting a device with an EFI partition table, we may need to
leave a gap between the GPT header (always in LBA 1) and the partition
entries. The GPT header already contains a field to specify the
on-disk location, which has so far always been set to LBA 2. With this
change, a configurable offset will be translated into a LBA address
indicating where to put the entries.
Now also allows an override via device-tree using a config-node (see
doc/device-tree-bindings/config.txt for documentation).
Tested (exporting an internal MMC formatted with this) against Linux,
MacOS X and Windows.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: __maybe_unused on config_offset to avoid warning]
Signed-off-by: Tom Rini <trini@konsulko.com>
If the ethernet address environment is set with a valid
ethernet address prevent overriding it as it is most likely
set by the user and he/she doesn't want board code to
automatically override it whatsoever.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
PRU ethernet MAC address range is present in the
board EEPROM. Parse it and setup eth?addr
environment variables.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
In stead of defining the board EEPROM address in the board headers
let's define them in the board config files and make them
configurable by Kconfig.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
AM571x IDK and AM572x IDK have optional LCD Kits that can be purchased.
These can be one of OSD101T2045 or the newer OSD101T2587. The LCD panel
itself has no registers that can be used to identify the panel, however,
the touchscreen controllers on the panels are different.
Hence to ease user experience, we can use the touch screen controller's
ID information to detect what kind of panel we use and select the
appropriate kernel dtb for the platform configuration.
NOTE: AM572x IDK default configuration is for LCD Connectivity, however
the AM571x IDK has a jumper (J51) that needs to be mounted for the IDK
to operate with LCD (Vs two PRUSS ethernet port option).
Touchscreen ID information is documented in:
http://www.osddisplays.com/TI/OSD101T2587-53TS_A.1.pdf
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Use the same convention that was used for ICSS1 Ethernet
- If pin is output, set as PIN_OUTPUT
- If pin is input and external pull resistor present set as PIN_INPUT
- If pin is input and external pull resistor absent, set pull to same
as that of the external PHY's internall pull.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The board can support either ICSS1 Ethernet ports or LCD
based on J51 jumper. Factory default is ICSS1 Ethernet ports
(i.e. Jumper not populated).
Use the GPIO to detect the jumper setting and configure the
pinmux accordingly. Also select the right DT blob based on
the chosen configuration.
J51 absent -> ICSS1 Ethernet, no LCD on VOUT -> am571x-idk.dtb
J51 present -> LCD on VOUT, no ICSS1 Ethernet -> am571x-idk-lcd-osd.dtb
At present we only support the assume it is the Legacy LCD.
LCD detection mechanism needs to be added later to differentiate
between legacy vs new LCD.
For ICSS1 Ethernet pins use the following convention to set the pinmux
as PMT data is not yet finalized.
- If pin is output, set as PIN_OUTPUT
- If pin is input and external pull resistor present set as PIN_INPUT
- If pin is input and external pull resistor absent, set pull to same
as that of the external PHY's internall pull.
- Do not use SLEW_CONTROLon any pin.
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Keystone and OMAP platforms will need this to set ethernet
MAC addresses from board EEPROM.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Scratch space can be used for features such as board detection. Define
an area within SRAM that can be used for this purpose.
[rogerq@ti.com] Rename EEPROM macro
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Non OMAP platforms i.e. Keystone will also need to use the board
EEPROM helpers so let's make the macro platform independent.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
GPIO_TO_PIN(bank, bank_gpio) returns the GPIO index
from the GPIO bank number and bank's GPIO offset number.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Enable more DM drivers. The imx I2C/MMC DM drivers needs DM_GPIO
enabled. So needs to enable them together.
DM FEC and SPI are not enabled, but they use gpio in board code.
So use gpio_request first to request the gpio, because DM_GPIO
is enabled.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Introduce device tree support.
dts from kernel commit c4f3f22edd Merge tag 'linux-kselftest-4.11-rc1'
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
- The catch-all i.MX6 job has been exceeding the time limit again so
split this up further. We now have an i.MX6 job and an
everything-else job.
- The logic we use to say "Freescale and AArch64" can be more clearly
expressed with '&' rather than excluding various other things, so
clear that up.
Signed-off-by: Tom Rini <trini@konsulko.com>
To keep a consistent MMC device mapping in SPL and in u-boot, let's
register the MMC controllers the same way in u-boot and in the SPL.
In terms of boot time, it doesn't hurt to register more controllers than
needed because the MMC device is initialized only prior being accessed for
the first time.
Having the same device mapping in SPL and u-boot allows us to use the
environment in SPL whatever the MMC boot device.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Move Freescale/NXP Vybrid to a standard arch/board approach, similar
to what has been done to i.MX 6 earlier in commit 89ebc82137 ("ARM:
mx6: move to a standard arch/board approach").
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Use two separate partitions for the two firmware instances. Also
resize them to be of the same size which also makes the start of
the UBI partition nicely aligned to 0x400000.
In order to detect the new MTD layout and whether we run a U-Boot
with the new BCB format or not, introduce a variable called
"updlevel" which we can use in update/upgrade scripts.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Use device-tree fixup to communicate the MTD partitions to the
kernel. Remove mtdparts from the kernel command line.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Implement board level USB PHY mode callback. On USB OTG Port 1
the Colibri standard foresees GPIO USBC_DET to decide whether the
port should run in Host or Device mode.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Limit memory used for relocation of FDT or initrd. This is
required to make sure that relocated artifacts are within lowmem.
If fdt_high or initrd_high are not set, U-Boot automatically
relocates artifacts to the end of memory. But this area won't
be part of lowmem and hence will not be accessible by the kernel
during early boot.
With VM split set to 2G/2G (i.MX default), only the 2GB Apalis
iMX6 is affected by that issue. With VM split set to 3G/1G (ARM
default) also modules with 1GB of memory are affected. With the
latter the amount of lowmem will be 760MiB.
The value must also not exceed available memory! Use a safe value
of 512MiB for Apalis and 256MiB for Colibri.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Device tree overlays might prove useful in the future, enable it
by default on all Toradex modules.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
All modules use the common g_dnl_bind_fixup implementaton which
calculates the PID according to product id (read from the config
block) plus offset of 0x4000. In case there is no config block
support (e.g. SPL) or in case the config block is not readable,
fall back to a generic product id (product id 0, which can be
interpreted as "Unknown Module").
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
According to the MX7D fuse map the following speed grades are available:
800 MHz
500 MHz
1000 MHz
1200 MHz
So simply return the real frequency that corresponds to the speed grade.
With this change we see on boot:
CPU: Freescale i.MX7D rev1.2 1000 MHz (running at 792 MHz)
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
According to the MX7D fuse map the speed grade of the parts, which
return '1' is 500MHz instead of 850MHz, so fix it accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
This is needed to make the UMS command work again as it fails with the
following error:
BIOS> ums 0 mmc 0
UMS: LUN 0, dev 0, hwpart 0, sector 0x0, count 0x748000
g_dnl_register: failed!, error: -19
ERROR: g_dnl_register failed
at cmd/usb_mass_storage.c:179/do_usb_mass_storage()
That's because usb_setup_ehci_gadget() function is looking for the usb
device using the req_sed number.
This change makes the usb device have a req_seq number and the UMS
command work again:
BIOS> ums 0 mmc 0
UMS: LUN 0, dev 0, hwpart 0, sector 0x0, count 0x748000
CTRL+C - Operation aborted
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
OPOS6UL is an i.MX6UL based SoM with 256MB RAM, 4GB eMMC and an ethernet
phy. OPOS6ULDev is carrier board for the OPOS6UL.
U-Boot SPL 2017.03-rc3-00002-g5085c26 (Mar 07 2017 - 09:48:09)
Trying to boot from MMC1
U-Boot 2017.03-rc3-00002-g5085c26 (Mar 07 2017 - 09:48:09 +0100)
CPU: Freescale i.MX6UL rev1.0 528 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 40C
Reset cause: POR
Model: Armadeus Systems OPOS6UL SoM on OPOS6ULDev board
DRAM: 256 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Video: 800x480x18
In: serial
Out: serial
Err: serial
Net: FEC [PRIME]
Hit any key to stop autoboot: 0
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Today, we have cases where we wish to build all of U-Boot in Thumb2 mode for
various reasons. We also have cases where we only build SPL in Thumb2 mode due
to size constraints and wish to build the rest of the system in ARM mode. So
in this migration we introduce a new symbol as well, SPL_SYS_THUMB_BUILD to
control if we build everything or just SPL (or in theory, just U-Boot) in
Thumb2 mode.
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Non-FIT SPL image loading support should be disabled for TI secure
devices as the image handlers for those image types do not follow
our secure boot flow.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a Kconfig option that enables Legacy image support, this allows
boards to explicitly disable this, for instance when needed for
security reasons.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Move to common/spl/Kconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
CONFIG_SPL_ABORT_ON_RAW_IMAGE causes SPL to abort and move on when it
encounters RAW images, express this same functionality as a positive
option enabling support for RAW images: CONFIG_SPL_RAW_IMAGE_SUPPORT
Also move uses of this to defconfigs.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Rework Kconfig logic a little, move to common/spl/Kconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
This includes support for rk3188 from Heiko Stübner and and rk3328 from
Kever Yang. Also included is SPL support for rk3399 and a fix for
rk3288 to get it booting again (spl_early_init()).
This driver uses the same pin control binding as that of linux, binding
document of this patch is copied from linux. One addition done is for
GPIO input and output mode configuration which was missing.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Before clock driver availability it was required to enable usart1 clock
for serial init but now with clock driver is taking care of usart1 clock.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
add basic clock driver support for stm32f7 to enable clocks required by
the peripherals.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds device tree support for stm32f7 serial driver & removes serial
platform data structure.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch cleans the code by using instructions allowed for armv7m as well as
other Arm archs.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
We only support cores that do Thumb-1 or later. So we add a comment to
explain this and remove the architecture test.
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Change GPT UUID string format from UUID to GUID per specification.
Signed-off-by: Vincent Tinelli <vincent.tinelli@intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
itest shell command doesn't work correctly in long format when
doing comparaison due to wrong mask value calculus that overflow
on 32 bits values.
Signed-off-by: Sebastien Colleur <sebastienx.colleur@intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Boards with an apparent need for the md5sum command had the connected
config symbol defined in their board header file.
Move this over to the respective defconfig files now that md5sum is
configured via Kconfig.
(This is a manual effort, which differs from moveconfig.py, not sure
who is right here. Boards except sandbox loose the md5sum command with
moveconfig.py, though it was explicitly mentioned in their config.h's)
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: migrate stih410-b2260]
Signed-off-by: Tom Rini <trini@konsulko.com>
FIT images require MD5 support to verify image checksums. So far this
was expressed by defining a CPP symbol in image.h. Since MD5 is now a
first class Kconfig citizen, express that in Kconfig instead.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
So far CONFIG_MD5SUM would need to be set by a board's include file.
Since the command is really generic, move it over to Kconfig to allow
it to be defined by either a board's defconfig, menuconfig or some
config snippet merged via mergeconfig.sh.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit 19a5944fcd ("mvgbe: remove setting of ethaddr within the
driver") removed the usage of get_random_hex() from the mvgbe driver
about six years ago. However the prototype of that function survived
till today in some kirkwood header file.
Remove that prototype and the CONFIG_MD5 dependency triggered by that.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This adds support for TQMa6DL using i.MX6DL and 1GiB DRAM
Since The module will use the same devicetree, we patch
the ram size in ft_board_setup.
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
We have a Kconfig name for the module types. Let's Use it.
Some feature selections and configurations are based on the
module. Module selection selects the CPU type.
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Add board_mmc_get_env_dev
Switch the mmc env based on the mmc devno, instead of separately
defining a config item in include/configs using board_mmc_get_env_dev
- devno 0: sd/esd
- devno 1: mmc/emmc
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Boot from eMMC:
--------------
U-Boot SPL 2017.01-00318-g8e243f8 (Jan 26 2017 - 11:53:21)
Trying to boot from MMC2
U-Boot 2017.01-00318-g8e243f8 (Jan 26 2017 - 11:53:21 +0100)
CPU: Freescale i.MX6D rev1.2 at 792 MHz
Reset cause: POR
Model: Engicam i.CoreM6 Quad/Dual RQS Starter Kit
DRAM: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
switch to partitions #0, OK
mmc1(part 0) is current device
Net: No ethernet found.
Hit any key to stop autoboot: 0
Booting from mmc ...
switch to partitions #0, OK
mmc1(part 0) is current device
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Since the CS are not in use, do not map them. User of starterkit
mainboard is free to use them otherwise. When using these pins later
in the OS for instance as GPIO IRQ pin, they need to be input.
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
The current driver stength is too high, leading to spec violations
on the falling edge. Fix it with values from HW
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
SPL mmc device index is get based on the boot device, like
- BOOT_DEVICE_MMC1 for mmc device 0
- BOOT_DEVICE_MMC2 for mmc device 1
Currently BOOT_DEVICE_MMC1 is setting both SD/eSD and MMC/eMMC
boot devices in i.MX, So u-boot is loading from mmc device 0 even
"if the board booting from SD/eSD or MMC/eMMC"
So, this patch set BOOT_DEVICE_MMC2 for MMC/eMMC so for MMC/eMMC
the u-boot is loading from mmc device 1 and the board file need to
take care if the board have different mmc device order intialization.
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add board_mmc_get_env_dev
Switch the mmc env based on the mmc devno, instead of separately
defining a config item in include/configs using board_mmc_get_env_dev
- devno 0: sd/esd
- devno 1: mmc/emmc
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Let the runtime code can set the mmcdev and mmcroot based
on the devno using mmc_get_env_dev instead of defining
separately in build-time configs using mmc_late_init func.
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add runtime, modeboot env which is setting mmcboot, or
nandboot based on the bootdevice so-that conditional
macros b/w MMC and NAND for CONFIG_BOOTCOMMAND should
be avoided in config files.
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
SPL mmc device index is get based on the boot device, like
- BOOT_DEVICE_MMC1 for mmc device 0
- BOOT_DEVICE_MMC2 for mmc device 1
Currently BOOT_DEVICE_MMC1 is setting both SD/eSD and MMC/eMMC
boot devices in i.MX, So u-boot is loading from mmc device 0 even
"if the board booting from SD/eSD or MMC/eMMC"
So, this patch set BOOT_DEVICE_MMC2 for MMC/eMMC so for MMC/eMMC
the u-boot is loading from mmc device 1 and the board file need to
take care if the board have different mmc device order intialization.
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Instead of initializing 'struct src' to SRC_BASE_ADDR on
every function better to have global define macro.
Reviewed by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Use meaningful macros IMX6_BMODE_*, instead of numerical
number in boot mode detection code.
Cc: Tim Harvey <tharvey@gateworks.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@openedev.com>
BOOT_CFG1[7:4] the NAND boot mode selection is done
only when BOOT_CFG1[7] is 1 hence update the NAND
boot mode detection bit case. This information available
on Table 8-11. NAND Boot eFUSE Descriptions, from IMX6DQRM.
Cc: Tim Harvey <tharvey@gateworks.com>
Reviewed by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@openedev.com>
For i.MX6, the bootmode determine code is part of spl_boot_device,
but there is might be a possibility for other part the code need to
check the desired boot mode for adding new functionalities like
modeboot env variable, or changing boot order etc.
So introduced imx6_src_get_boot_mode which actually reading the
boot mode register for desired modes.
More cleanup will be add in future patches.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Boot from MMC:
-------------
U-Boot SPL 2017.01-rc2-gba3c151-dirty (Jan 02 2017 - 16:59:33)
Trying to boot from MMC1
U-Boot 2017.01-rc2-gba3c151-dirty (Jan 02 2017 - 16:59:33 +0100)
CPU: Freescale i.MX6UL rev1.1 528 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 33C
Reset cause: POR
Model: Engicam Is.IoT MX6UL Starterkit
DRAM: 512 MiB
MMC: FSL_SDHC: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
isiotmx6ul>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enable MMC support.
The fsl sdhc driver needs regulator to enable power, so enable
regulator support.
And bootcmd and more env.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Add compatible property for i.MX7ULP.
Add a weak init_usdhc_clk function, i.MX7ULP use this to init the clock.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
Add CAAM clock functions, SEC_CONFIG[1] fuse checking, and default CSF
size for HAB support boot on mx7ulp.
Users need to uncomment the CONFIG_SECURE_BOOT in mx7ulp_evk.h to build
secure uboot.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
Drop CONFIG_LPUART_32B_REG.
Move the register structure to a common file include/fsl_lpuart.h
Define lpuart_serial_platdata structure which includes the reg base and flags.
For 32Bit register access, use lpuart_read32/lpuart_write32 which handles
big/little endian.
For 8Bit register access, still use the orignal code.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Shaohui Xie <Shaohui.Xie@nxp.com>
Cc: Alison Wang <b18965@freescale.com>
Add lpi2c driver for i.MX7ULP.
Need to enable the two options to use this driver:
CONFIG_DM_I2C=y
CONFIG_SYS_I2C_IMX_LPI2C=y
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Heiko Schocher <hs@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Add i.MX7ULP pinctrl driver.
Select CONFIG_PINCTRL_IMX7ULP to use this driver.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by : Stefano Babic <sbabic@denx.de>
This driver implements the HW WATCHDOG functions. Which needs
to set CONFIG_HW_WATCHDOG to use them. This is disabled by default for
mx7ulp.
Use watchdog for reset cpu. Implement this in the driver.
Need to define CONFIG_ULP_WATCHDOG to build it.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Add the iomux pins header file from iomux tool team. Change the IOMUXC0 pins
to add IOMUX_CONFIG_MPORTS flags.
Note: The IOMUXC0 offset provided in this file is from 0xD000, this is not
aligned with IOMUXC0 base address. We have adjusted the IOMUXC0 base address
to aligin with it.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Update the mxc_ocotp driver to support i.MX7ULP.
The read/write sequence has some changes due to
PDN and OUT_STATUS registers added and TIME register is
removed. Also update the bank size and number.
Add is_mx7ulp macro in sys_proto.h
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
Add the imx_rgpio2p driver for Rapid GPIO2P controllers on i.MX7ULP.
Have added all ports on RGPIO2P_0 and RGPIO2P_1.
The configurations CONFIG_IMX_RGPIO2P and CONFIG_DM_GPIO must be set
to y to enable the drivers.
To use the GPIO function, the IBE and OBE needs to set in IOMUXC.
We did not set the bits in driver, but leave them to IOMUXC settings
of the GPIO pins. User should use IMX_GPIO_NR to generate the GPIO number
for gpio APIs access.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
Implement the i2c clock enable and get function for mx7ulp. These
functions are required by imx_lpi2c driver.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Implement soc level functions to get cpu rev, reset cause, enable cache,
etc. We will disable the wdog and init clocks in s_init at very early u-boot
phase.
Since the we are seeking the way to get chip id for mx7ulp, the get_cpu_rev
is hard coded to a fixed value. This may change in future.
Reuse some code in imx-common.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Add a clock framework to support SCG1/PCC2/PCC3 for A7 to support get/set
clock source, divider, clock rate and parent source.
Users need to include pcc.h to use the APIs to for peripherals clock. Each
peripheral clock is defined in enum pcc_clk type.
SCG relevants APIs are defined in scg.h which supports clock rate get, PLL/PFD
enablement and settings, and all SCG clock initialization. User need use enum
scg_clk to access each clock source.
In clock.c, we initialize necessary clocks at u-boot s_init and implement the
clock functions used by driver modules to operate clocks dynamically.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Add a new driver under ULP directory to support its IOMUXC
controllers. The ULP has two IOMUXC, the IOMUXC0 is used
for M4 domain, while IOMUXC1 is for A7. We set IOMUXC1 as
the default IOMUX in this driver. Any pins in IOMUXC0 needs
to configure with IOMUX_CONFIG_MPORTS in its mux_mode field.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
Add imx-regs.h for i.MX7ULP registers addresses definitions and some
registers structures.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
i.MX7ULP is a new series SoC which has different architecture
from previous i.MX platforms. Create a new cpu folder for it,
and add it to Kconfig.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
Despite the comment in the code, CSC unit is never used. According to
the only public description of DW HDMI controller (i.MX6 manual), CSC
unit is bypassed in MC_FLOWCTRL register and then actually powered
down in MC_CLKDIS register.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
Function hdmi_lookup_n_cts() is feed with clock in Hz, which gets
compared with clocks in kHz. Fix that by converting all clocks to Hz.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
RK3288 using the dwc2 USB host controller, enable it and other usb host
funtion like storage and ethernet.
Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tinker board have a usb host. add dts node to provide power supply.
Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit e856bdcfb4 ("flash: complete CONFIG_SYS_NO_FLASH move with renaming")
obsoleted the CONFIG_SYS_NO_FLASH option, which still is in our
rk3188_common.h header, resulting in warnings like
The following new ad-hoc CONFIG options were detected:
CONFIG_SYS_NO_FLASH
So also drop it from the rk3188 header.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
Documentation says that we're returning true/false, not 1/0 so adapt
the function to return actual booleans.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
At current, only firefly and rock2 have network enabled.
Let's enable other boards.
Signed-off-by: Jacob Chen <jacob2.chen@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Enable board config for evb-rk3328.
SDcard and eMMC boot is OK in this initial version,
USB and EMAC function is not available now, will comes later.
Signed-off-by: William Zhang <william.zhang@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
evb-rk3328 is an evb from Rockchip based on rk3328 SoC:
- 2 USB2.0 Host port;
- 1 USB3.0 Host port;
- 1 HDMI port;
- 2 10/100M eth port;
- 2GB ddr;
- 16GB eMMC;
- UART to USB debug port;
Signed-off-by: William Zhang <william.zhang@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
RK3328 is a SoC from Rockchip with quad-core Cortex-A53 CPU.
It supports two USB2.0 EHCI ports. Other interfaces are very
much like RK3288, the DRAM are 32bit width address and support
address from 0 to 4GB-16MB range.
Signed-off-by: William Zhang <william.zhang@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add empty arch/arm/mach-rockchip/rk3328/Kconfig to avoid build error:
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable all the CONFIGs which need by SPL.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Added rockchip tag:
Drop CONFIG_ROCKCHIP_DWMMC for now due to build error:
Move changes to arch/arm/mach-rockchip/Kconfig to this patch:
Signed-off-by: Simon Glass <sjg@chromium.org>
Add SPL support for rk3399, default with of-platdata enabled.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Drop Kconfig changes to fix build error:
Signed-off-by: Simon Glass <sjg@chromium.org>
Add syscon and dmc node, and 'u-boot,dm-pre-reloc' option for
required driver.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Added rockchip tag:
Signed-off-by: Simon Glass <sjg@chromium.org>
RK3399 support DDR3, LPDDR3, DDR4 sdram, this patch is porting from
coreboot, support 4GB lpddr3 in this version.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Added rockchip: tag:
Signed-off-by: Simon Glass <sjg@chromium.org>
We are using wrong mmc instance as boot target device now. below Jaehoon Chung's
patch use mmc alias which correct it. That make tinker board can not find mmc
device. So give it correct mmc device instance.
commit 02ad33aa3a
Author: Jaehoon Chung <jh80.chung@samsung.com>
Date: Thu Feb 2 13:41:14 2017 +0900
mmc: mmc-uclass: use the fixed devnum with alias node
Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
We should remove config_spl_of_platdata to build u-boot-spl-dtb.bin rather than u-boot-spl-nodtb.bin
since we use spl_back_to_brom.
I miss it because i forget to clean build-dir..
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Acked-by: Simon Glass <sjg@chromium.org>
The rk3188 needs 3 U-Boot stages: a tpl living in 1KB of sram, a spl
the resides in the rest of the sram and loads the regular U-Boot living
in regular ram.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
The sdram controller blocks are very similar to the rk3288 in utilizing
memory scheduler, Designware uPCTL and Designware PUBL blocks, only
limited to one bank instead of two.
There are some minimal differences when setting up the ram, so it gets
a separate driver for the rk3188 but reuses the driver structs, as there
is no need to define the same again.
More optimization can happen when the modelling of the controller parts
in the dts actually follow the hardware layout hopefully at some point
in the future.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Add the core architecture code for the rk3188.
It doesn't support the SPL yet, as because of some
unknown error it doesn't start yet.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Drop these defines from rk3188_common.h
CONFIG_GENERIC_MMC, CONFIG_BOUNCE_BUFFER, CONFIG_DOS_PARTITION
CONFIG_PARTITION_UUIDS, CONFIG_CMD_PART:
Signed-off-by: Simon Glass <sjg@chromium.org>
The rk3188 shares a lot of peripherals with the rk3066 and thus
has a common include called rk3xxx.dtsi. Add both this one and
the specialized rk3188 on top of it.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Add a driver for setting up and modifying the various PLLs and peripheral
clocks on the RK3188.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Bring in required device clock binding files from Linux.
The clock trees for rk3066 and rk3188 are largely similar, which makes
them share the common parts in a shared header. While we focus on rk3188
for now, bring in both headers already for completeness sake.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Add a driver which supports pin multiplexing setup for the most commonly
used peripherals.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
PMU is the power management unit and GRF is the general register file. Both
are heavily used in U-Boot. Add header files with register definitions.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Rockchip SoCs allow the spl code to be rc4-encoded, not only the
image header, but only newer SoCs allow this encoding to be disabled.
The rk3188 is not part of those and requires its boot code to be
rc4-encoded with the regular key. So add the ability to do this
encoding via a setting on a per-soc basis when building spl images.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
So far spl-boards have declared the back_to_brom() function as simple
extern in the files themself. That doesn't scale well if every boards
defines this on its own.
Therefore move the declarations to a bootrom header.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Right now the ROCKCHIP_SPL_BACK_TO_BROM option both triggers
compilation of the bootrom hook-code as well as enabling the
behaviour of loading the full U-Boot via the boot.
New added socs may always need the bootrom code, while still
being able to decide between loading U-Boot regularly or via
the bootrom separately.
So move the compilation of the bootrom code to a hidden option
that gets selected by ROCKCHIP_SPL_BACK_TO_BROM, but can also
be selected by other parts.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
The sdram IP blocks used on rk3066, rk3188 and rk3288 are very similar
and we want to unify things once all 3 work as expected.
Therefore try to keep the rk3288 sdram driver in line by applying the
general review comments received for the rk3188 variant to it as well.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
Use defines to describe the bit shifts used to create the
table for ddrconf register values.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
The gpll and cpll init values are only used in rk_clk_init in the SPL
and therefore produce compile time warnings in regular uboot builds.
Fix that with an #ifdef.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
Added rockchip tag:
Signed-off-by: Simon Glass <sjg@chromium.org>
Right now the u-boot,dm-pre-reloc flag will make each marked node
always appear in both spl and tpl. But systems needing an additional
tpl might have special constraints for each, like the spl needing to
be very tiny.
So introduce two additional flags to mark nodes for only spl or tpl
environments and introduce a function dm_fdt_pre_reloc to automate
the necessary checks in code instances checking for pre-relocation
flags.
The behaviour of the original flag stays untouched and still marks
a node for both spl and tpl.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
rk3399 has different syscon registers which may used in spl,
add to support rk3399 spl.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Added rockchip tag:
Signed-off-by: Simon Glass <sjg@chromium.org>
rk3399 grf register bit defenitions should locate in header
file, so that not only pinctrl can use it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Added rockchip tag:
Signed-off-by: Simon Glass <sjg@chromium.org>
Use spl_early_init() to make sure that early malloc() is initialised. This
fixes booting on firefly-rk3288, for example.
Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Eddie Cai <eddie.cai.linux@gmail.com>
At present malloc_base/_limit/_ptr are not initialised in spl_init() when
we call spl_init() in board_init_f(). This is due to a recent change aimed
at avoiding overwriting the malloc area set up on some boards by
spl_relocate_stack_gd().
However if CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN is not defined, we now
skip setting up the memory area in spl_init() which is obviously wrong.
To fix this, add a new function spl_early_init() which can be called in
board_init_f().
Fixes: b3d2861e (spl: Remove overwrite of relocated malloc limit)
Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Rewrote spl_{,early_}init() to avoid duplicate code:
Rewrite/expand commit message:
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Eddie Cai <eddie.cai.linux@gmail.com>
At first, the ARM64 Linux booting requirement recommended that the
kernel image be placed text_offset bytes from 2MB aligned base near
the start of usable system RAM because memory below that base address
was unusable at that time.
This requirement was relaxed by Linux commit a7f8de168ace ("arm64:
allow kernel Image to be loaded anywhere in physical memory").
Since then, the bit 3 of the flags field indicates the tolerance
of the kernel physical placement. If this bit is set, the 2MB
aligned base may be anywhere in physical memory. For details, see
Documentation/arm64/booting.txt of Linux.
The booti command should be also relaxed. If the bit 3 is set,
images->ep is respected, and the image is placed at the nearest
bootable location. Otherwise, it is relocated to the start of the
system RAM to keep the original behavior.
Another wrinkle we need to take care of is the unknown endianness of
text_offset for a kernel older than commit a2c1d73b94ed (i.e. v3.16).
We can detect this based on the image_size field. If the field is
zero, just use a fixed offset 0x80000.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Richard reported U-Boot tools issues in OpenEmbedded/Yocto project.
OE needs to be able to change the default compiler. If we pass in
HOSTCC through the make command, it overwrites all HOSTCC instances,
including ones in tools/Makefile and tools/env/Makefile, which breaks
"make cross_tools" and "make env", respectively.
Add "override" directives to avoid overriding HOSTCC instances that
really need to point to the cross-compiler.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reported-by: Richard Purdie <richard.purdie@linuxfoundation.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Leave only detected flash type enabled in FTD as otherwise GPMC CS is
claimed (and never freed) by Linux, causing 'concurent' flash type
not to be probed.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
ISEE's U-Boot and Linux are using 1bit ECC scheme, while we
switched to 8bit ECC to fullfill flash specification requirements.
However when trying to run U-Boot on board with 1bit ECC'd data
on flash, UBI code takes several minutes to pass scan as reading
of every block ends with ecc error (which is also printed on
console).
So, until proper solution is developed, disable environment
alltogether.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
This is a 96Board compliant board based on STiH410 SoC:
- 1GB DDR
- On-Board USB combo WiFi/Bluetooth RTL8723BU
with PCB soldered antenna
- Ethernet 1000-BaseT
- SATA
- HDMI
- 2 x USB2.0 type A
- 1 x USB2.0 type micro-AB
- SD card slot
- High speed connector (SD/I2C/USB interfaces)
- Low speed connector (UART/I2C/GPIO/SPI/PCM interfaces)
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add SDHCI host controller found on STMicroelectronics SoCs
On some ST SoCs, i.e. STiH407/STiH410, the MMC devices can live
inside a dedicated flashSS sub-system that provides an extend subset
of registers that can be used to configure the Arasan MMC/SD Host
Controller.
This means, that the SDHCI Arasan Controller can be configured to be
eMMC4.5 or 4.3 spec compliant.
W/o these settings the SDHCI will configure and use the MMC/SD
controller with limited features e.g. PIO mode, no DMA, no HS etc.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
As no gpio.h is defined in arch/arm/include/asm/arch-stih410,
to avoid compilation failure, do not include asm/arch/gpio.h.
This is needed for example when including sdhci.h, which include
asm/gpio.h>.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds support to ASC (asynchronous serial controller)
driver, which is basically a standard serial driver. This IP
is common across other STMicroelectronics SoCs
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The STiH410 is an advanced multi-HD AVC processor with 3D
graphics acceleration and 1.5-GHz ARM Cortex-A9 SMP CPU
part of the STiH407 family.
It has wide connectivity including USB 3.0, PCI-e, SATA
and gigabit ethernet.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
The SysTick is a 24-bit down counter that is found on all ARM Cortex
M3, M4, M7 devices and is always located at a fixed address.
The number of reference clock ticks that correspond to 10ms is normally
defined in the SysTick Calibration register's TENMS field. However, on some
devices this is wrong, so this driver allows the clock rate to be defined
using CONFIG_SYS_HZ_CLOCK.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Vikas MANOCHA <vikas.manocha@st.com>
The size field in GP header that is expected by ROM is size of the
image + size of the header. But omapimage generates a gp header
only with size of the image as size field. Fix it
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The workaround for ARM errata 725233 had been lost since
commit 45bf05854b (armv7: adapt omap3 to the new cache
maintenance framework). Bring it back in order to avoid
very difficult to reproduce, but actually encountered in
the wild CPU deadlocks when running software rendered
X11 desktop on OMAP3530 hardware.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Migrate to Kconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
Boards with OMAP3530 SoC fail to boot since commit bd2c4522c2
("ti: armv7: enable EXT support in SPL (using ti_armv7_common.h)")
because it enabled the use of Thumb2 for the SPL.
Experiments have shown that the deadlock happens in the
prcm_init() function from 'arch/arm/mach-omap2/omap3/clock.c'.
This patch enforces the compilation of clock.c source file in
ARM mode and makes the deadlock disappear. We are yet to figure
out the root cause of the problem. Still this is somewhat
better than having non-bootable boards for years.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Borrowing from omap3_logic, switch to SPL_SYS_MALLOC_SIMPLE and moving
the stack to DDR as soon as we're able.
Signed-off-by: Tom Rini <trini@konsulko.com>
Raw uboot image is used in place of FIT image in secure boot.
The maximum allocated size of raw u-boot bin is 1MB in memory map.
Hence , CONFIG_SYS_MONITOR_LEN has been modified to 1 MB.
The bootscript (BS_ADDR) and its header (BS_HDR_ADDR) offset on
MMC have also been modified to accommodate the increase in uboot size.
Signed-off-by: Vinitha Pillai-B57223 <vinitha.pillai@nxp.com>
Reviewed-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
VID support in NXP layerscape Chassis-3 (lsch3) compilant SoCs like
LS2088A, LS2080A differs from existing logic.
-VDD voltage array is different
-Registers are different
-VDD calculation logic is different
Add new function adjust_vdd() for LSCH3 compliant SoCs
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Arpit Goel <arpit.goel@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Remove the DDR interactive debugging to reduce the size of spl image.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Read DMA operations causes CRC error on armv8 chassis 2 platforms
due to the erratum A-010635.
In order to support sata on these platforms, ECC needs to be disabled.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
In early MMU table, DDR has to be mapped as device memory to avoid
speculative access. After DDR is initialized, it needs to be updated
to normal memory to allow code execution. To simplify the code,
dram_init() is moved into a common file as a weak function.
Signed-off-by: York Sun <york.sun@nxp.com>
Function mmu_change_region_attr() is added to change existing mapping
with updated PXN, UXN and memory type. This is a break-before-make
process during which the mapping becomes fault (invalid) before final
attributres are set.
Signed-off-by: York Sun <york.sun@nxp.com>
Early MMU improves performance especially on emulators. However, the
early MMU is left enabled after the first stage of SPL boot. Instead
of flushing D-cache and dealing with re-enabling MMU for the second
stage U-Boot, disabling it for SPL build simplifies the process. The
performance penalty is unnoticeable on the real hardware. As of now,
SPL boot is not supported by existing emulators. So this should have
no impact on emulators.
Signed-off-by: York Sun <york.sun@nxp.com>
This patch follows the break-before-make process when making changes
to MMU table. MMU is disabled before changing TTBR to avoid any
potential race condition.
Signed-off-by: York Sun <york.sun@nxp.com>
Update mapping with actual DDR size. Non-existing memory should not
be mapped as "normal" memory to avoid speculative access.
Signed-off-by: York Sun <york.sun@nxp.com>
Since the reserved RAM is tracked by gd->arch.resv_ram, calculation
of MC memory blocks can be simplified. The MC RAM is guaranteed to be
aligned by the reservation process.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Priyanka Jain <priyanka.jain@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
For ARMv8 Layerscape SoCs, secure memory and MC memorey are reserved
at the end of DDR. DDR is spit into two or three banks. This patch
reverts commit aabd7ddb and simplifies the calculation of reserved
memory, and moves the code into common SoC file. Secure memory is
carved out first. DDR bank size is reduced. Reserved memory is then
allocated on the top of available memory. U-Boot still has access
to reserved memory as data transferring is needed. Device tree is
fixed with reduced memory size to hide the reserved memory from OS.
The same region is reserved for efi_loader.
Signed-off-by: York Sun <york.sun@nxp.com>
Instead of adding all memory banks, add a hook so individual SoC/board
can has its own implementation.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Alexander Graf <agraf@suse.de>
Reviewed-by: Alexander Graf <agraf@suse.de>
Fix warnings reported when built with W=1, by DTC 1.4.2 or later:
Node /memory has a reg or ranges property, but no unit name
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Linux Commit 9c0da3cc61f1 ("ARM: dts: explicitly mark skeleton.dtsi
as deprecated") declared that skeleton.dtsi was deprecated.
Move the memory node below to suppress warnings of FDTGREP.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Commit 04cd4e7215 ("ARM: uniphier: remove DRAM base address from
board parameters") accidentally unset the DRAM_SPARSE flag, and
changed the physical map of the DRAM channels. Revive the original
behavior.
Fixes: 04cd4e7215 ("ARM: uniphier: remove DRAM base address from board parameters")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reported-by: Shunji Sato <sato.shunji@socionext.com>
The maximum supported peripheral clock frequency of the zynq depends on
the IO routing. The MIO and EMIO support a maximum frequency of 50 MHz
respectively 25 MHz. Use the max-frequency value of the device tree to
determine the maximal supported peripheral clock frequency.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The zynq_sdhci controller driver use CONFIG_ZYNQ_SDHCI_MAX_FREQ as base
clock frequency but this clock is not fixed and depends on the hardware
configuration. Additionally the value of CONFIG_ZYNQ_SDHCI_MAX_FREQ
doesn't match the real base clock frequency of SDIO_FREQ. Use the clock
framework to determine the frequency at run time.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Move the zynq to clock framework and remove unused functions as well as
the CONFIG_ZYNQ_PS_CLK_FREQ configuration.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add a clock framework driver for the zynq platform. The driver is based
on the platform zynq clock driver but reworked to use static functions
instead of run-time generated objects even for unused clocks.
Additionally the CONFIG_ZYNQ_PS_CLK_FREQ is replaced by the
ps-clk-frequency from the device tree.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The gem[0-1]_rclk_ctrl registers control the source of the rx clock,
control and data signals and configure via ps7_init function. Don't
overwrite the register with the default value.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-02-17 10:22:46 +01:00
3101 changed files with 80837 additions and 115708 deletions
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
