Prepare v2019.07

Signed-off-by: Tom Rini <trini@konsulko.com>

.travis.yml

@@ -50,6 +50,7 @@ install:
  - . /tmp/venv/bin/activate
  - pip install pytest==2.8.7
  - pip install python-subunit
+ - pip install pyelftools
  - grub-mkimage -o ~/grub_x86.efi -O i386-efi normal  echo lsefimmap lsefi lsefisystab efinet tftp minicmd
  - grub-mkimage -o ~/grub_x64.efi -O x86_64-efi normal  echo lsefimmap lsefi lsefisystab efinet tftp minicmd
  - mkdir ~/grub2-arm
@@ -183,6 +184,9 @@ matrix:
     - name: "buildman NXP AArch64 LS101x"
       env:
         - BUILDMAN="freescale&aarch64&ls101"
+    - name: "buildman NXP AArch64 LS102x"
+      env:
+        - BUILDMAN="freescale&aarch64&ls102"
     - name: "buildman NXP AArch64 LS104x"
       env:
         - BUILDMAN="freescale&aarch64&ls104"
@@ -192,6 +196,9 @@ matrix:
     - name: "buildman NXP AArch64 LS20xx"
       env:
         - BUILDMAN="freescale&aarch64&&ls20"
+    - name: "buildman NXP AArch64 LX216x"
+      env:
+        - BUILDMAN="freescale&aarch64&lx216"
     - name: "buildman i.MX6 (non-NXP)"
       env:
         - BUILDMAN="mx6 -x freescale,toradex,boundary,engicam"

Documentation/devicetree/bindings/net/ethernet.txt

@@ -0,0 +1,66 @@
+The following properties are common to the Ethernet controllers:
+
+NOTE: All 'phy*' properties documented below are Ethernet specific. For the
+generic PHY 'phys' property, see
+Documentation/devicetree/bindings/phy/phy-bindings.txt.
+
+- local-mac-address: array of 6 bytes, specifies the MAC address that was
+  assigned to the network device;
+- mac-address: array of 6 bytes, specifies the MAC address that was last used by
+  the boot program; should be used in cases where the MAC address assigned to
+  the device by the boot program is different from the "local-mac-address"
+  property;
+- nvmem-cells: phandle, reference to an nvmem node for the MAC address;
+- nvmem-cell-names: string, should be "mac-address" if nvmem is to be used;
+- max-speed: number, specifies maximum speed in Mbit/s supported by the device;
+- max-frame-size: number, maximum transfer unit (IEEE defined MTU), rather than
+  the maximum frame size (there's contradiction in the Devicetree
+  Specification).
+- phy-mode: string, operation mode of the PHY interface. This is now a de-facto
+  standard property; supported values are:
+  * "internal"
+  * "mii"
+  * "gmii"
+  * "sgmii"
+  * "qsgmii"
+  * "tbi"
+  * "rev-mii"
+  * "rmii"
+  * "rgmii" (RX and TX delays are added by the MAC when required)
+  * "rgmii-id" (RGMII with internal RX and TX delays provided by the PHY, the
+     MAC should not add the RX or TX delays in this case)
+  * "rgmii-rxid" (RGMII with internal RX delay provided by the PHY, the MAC
+     should not add an RX delay in this case)
+  * "rgmii-txid" (RGMII with internal TX delay provided by the PHY, the MAC
+     should not add an TX delay in this case)
+  * "rtbi"
+  * "smii"
+  * "xgmii"
+  * "trgmii"
+  * "2000base-x",
+  * "2500base-x",
+  * "rxaui"
+  * "xaui"
+  * "10gbase-kr" (10GBASE-KR, XFI, SFI)
+- phy-connection-type: the same as "phy-mode" property but described in the
+  Devicetree Specification;
+- phy-handle: phandle, specifies a reference to a node representing a PHY
+  device; this property is described in the Devicetree Specification and so
+  preferred;
+- phy: the same as "phy-handle" property, not recommended for new bindings.
+- phy-device: the same as "phy-handle" property, not recommended for new
+  bindings.
+- rx-fifo-depth: the size of the controller's receive fifo in bytes. This
+  is used for components that can have configurable receive fifo sizes,
+  and is useful for determining certain configuration settings such as
+  flow control thresholds.
+- tx-fifo-depth: the size of the controller's transmit fifo in bytes. This
+  is used for components that can have configurable fifo sizes.
+- managed: string, specifies the PHY management type. Supported values are:
+  "auto", "in-band-status". "auto" is the default, it usess MDIO for
+  management if fixed-link is not specified.
+
+Child nodes of the Ethernet controller are typically the individual PHY devices
+connected via the MDIO bus (sometimes the MDIO bus controller is separate).
+They are described in the phy.txt file in this same directory.
+For non-MDIO PHY management see fixed-link.txt.

Kconfig

@@ -20,6 +20,13 @@ config BROKEN
 	  This option cannot be enabled. It is used as dependency
 	  for broken and incomplete features.
 
+config DEPRECATED
+	bool
+	help
+	  This option cannot be enabled.  It it used as a dependency for
+	  code that relies on deprecated features that will be removed and
+	  the conversion deadline has passed.
+
 config LOCALVERSION
 	string "Local version - append to U-Boot release"
 	help
@@ -138,6 +145,8 @@ config SYS_MALLOC_F_LEN
 	depends on SYS_MALLOC_F
 	default 0x1000 if AM33XX
 	default 0x2800 if SANDBOX
+	default 0x2000 if (ARCH_IMX8 || ARCH_IMX8M || ARCH_MX7 || \
+			   ARCH_MX7ULP || ARCH_MX6 || ARCH_MX5)
 	default 0x400
 	help
 	  Before relocation, memory is very limited on many platforms. Still,
@@ -241,7 +250,7 @@ config BUILD_TARGET
 	default "u-boot-with-spl.sfp" if TARGET_SOCFPGA_GEN5
 	default "u-boot-spl.kwb" if ARCH_MVEBU && SPL
 	default "u-boot-elf.srec" if RCAR_GEN3
-	default "u-boot.itb" if SPL_LOAD_FIT && ARCH_SUNXI
+	default "u-boot.itb" if SPL_LOAD_FIT && (ROCKCHIP_RK3399 || ARCH_SUNXI)
 	default "u-boot.kwb" if KIRKWOOD
 	default "u-boot-with-spl.bin" if ARCH_AT91 && SPL_NAND_SUPPORT
 	help
@@ -251,6 +260,23 @@ config BUILD_TARGET
 	  special image will be automatically built upon calling
 	  make / buildman.
 
+config SYS_CUSTOM_LDSCRIPT
+	bool "Use a custom location for the U-Boot linker script"
+	help
+	  Normally when linking U-Boot we will look in the board directory,
+	  the CPU directory and finally the "cpu" directory of the architecture
+	  for the ile "u-boot.lds" and use that as our linker.  However, in
+	  some cases we need to provide a different linker script.  To do so,
+	  enable this option and then provide the location under
+	  CONFIG_SYS_LDSCRIPT.
+
+config SYS_LDSCRIPT
+	depends on SYS_CUSTOM_LDSCRIPT
+	string "Custom ldscript location"
+	help
+	  Path within the source tree to the linker script to use for the
+	  main U-Boot binary.
+
 endmenu		# General setup
 
 menu "Boot images"
@@ -389,7 +415,7 @@ config SPL_FIT_SIGNATURE
 	select SPL_RSA
 
 config SPL_LOAD_FIT
-	bool "Enable SPL loading U-Boot as a FIT"
+	bool "Enable SPL loading U-Boot as a FIT (basic fitImage features)"
 	select SPL_FIT
 	help
 	  Normally with the SPL framework a legacy image is generated as part
@@ -400,7 +426,7 @@ config SPL_LOAD_FIT
 	  and passing the correct one to U-Boot.
 
 config SPL_LOAD_FIT_FULL
-	bool "Enable SPL loading U-Boot as a FIT"
+	bool "Enable SPL loading U-Boot as a FIT (full fitImage features)"
 	select SPL_FIT
 	help
 	  Normally with the SPL framework a legacy image is generated as part

MAINTAINERS

@@ -55,7 +55,7 @@ M:	Alexey Brodkin <alexey.brodkin@synopsys.com>
 M:	Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
 S:	Maintained
 L:	uboot-snps-arc@synopsys.com
-T:	git git://git.denx.de/u-boot-arc.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-arc.git
 F:	arch/arc/
 F:	board/synopsys/
 
@@ -84,7 +84,7 @@ F:	drivers/mmc/snps_dw_mmc.c
 ARM
 M:	Albert Aribaud <albert.u.boot@aribaud.net>
 S:	Maintained
-T:	git git://git.denx.de/u-boot-arm.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-arm.git
 F:	arch/arm/
 F:	cmd/arm/
 
@@ -92,14 +92,14 @@ ARM ALTERA SOCFPGA
 M:	Marek Vasut <marex@denx.de>
 M:	Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
 S:	Maintainted
-T:	git git://git.denx.de/u-boot-socfpga.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-socfpga.git
 F:	arch/arm/mach-socfpga/
 
 ARM AMLOGIC SOC SUPPORT
 M:	Neil Armstrong <narmstrong@baylibre.com>
 S:	Maintained
 L:	u-boot-amlogic@groups.io
-T:	git git://git.denx.de/u-boot-amlogic.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic.git
 F:	arch/arm/mach-meson/
 F:	arch/arm/include/asm/arch-meson/
 F:	drivers/clk/meson/
@@ -153,10 +153,11 @@ M:	Stefano Babic <sbabic@denx.de>
 M:	Fabio Estevam <festevam@gmail.com>
 R:	NXP i.MX U-Boot Team <uboot-imx@nxp.com>
 S:	Maintained
-T:	git git://git.denx.de/u-boot-imx.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-imx.git
 F:	arch/arm/cpu/arm1136/mx*/
 F:	arch/arm/cpu/arm926ejs/mx*/
 F:	arch/arm/cpu/armv7/vf610/
+F:	arch/arm/dts/*imx*
 F:	arch/arm/mach-imx/
 F:	arch/arm/include/asm/arch-imx/
 F:	arch/arm/include/asm/arch-mx*/
@@ -173,7 +174,7 @@ F:	arch/arm/include/asm/arch-hi6220/
 ARM MARVELL KIRKWOOD ARMADA-XP ARMADA-38X ARMADA-37XX ARMADA-7K/8K
 M:	Stefan Roese <sr@denx.de>
 S:	Maintained
-T:	git git://git.denx.de/u-boot-marvell.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-marvell.git
 F:	arch/arm/mach-kirkwood/
 F:	arch/arm/mach-mvebu/
 F:	drivers/ata/ahci_mvebu.c
@@ -187,7 +188,7 @@ F:	drivers/watchdog/orion_wdt.c
 ARM MARVELL PXA
 M:	Marek Vasut <marex@denx.de>
 S:	Maintained
-T:	git git://git.denx.de/u-boot-pxa.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-pxa.git
 F:	arch/arm/cpu/pxa/
 F:	arch/arm/include/asm/arch-pxa/
 
@@ -216,7 +217,7 @@ N:	mediatek
 ARM MICROCHIP/ATMEL AT91
 M:	Eugen Hristev <eugen.hristev@microchip.com>
 S:	Maintained
-T:	git git://git.denx.de/u-boot-atmel.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-atmel.git
 F:	arch/arm/mach-at91/
 F:	board/atmel/
 
@@ -233,7 +234,7 @@ ARM RENESAS RMOBILE/R-CAR
 M:	Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
 M:	Marek Vasut <marek.vasut+renesas@gmail.com>
 S:	Maintained
-T:	git git://git.denx.de/u-boot-sh.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-sh.git
 F:	arch/arm/mach-rmobile/
 
 ARM ROCKCHIP
@@ -241,7 +242,7 @@ M:	Simon Glass <sjg@chromium.org>
 M:	Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
 M:	Kever Yang <kever.yang@rock-chips.com>
 S:	Maintained
-T:	git git://git.denx.de/u-boot-rockchip.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip.git
 F:	arch/arm/include/asm/arch-rockchip/
 F:	arch/arm/mach-rockchip/
 F:	board/rockchip/
@@ -263,13 +264,13 @@ F:	tools/rkspi.c
 ARM SAMSUNG
 M:	Minkyu Kang <mk7.kang@samsung.com>
 S:	Maintained
-T:	git git://git.denx.de/u-boot-samsung.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-samsung.git
 F:	arch/arm/mach-exynos/
 F:	arch/arm/mach-s5pc1xx/
 F:	arch/arm/cpu/armv7/s5p-common/
 
 ARM SNAPDRAGON
-M:	Ramon Fried <ramon.fried@gmail.com>
+M:	Ramon Fried <rfried.dev@gmail.com>
 S:	Maintained
 F:	arch/arm/mach-snapdragon/
 F:	drivers/gpio/msm_gpio.c
@@ -288,13 +289,12 @@ F:	arch/arm/include/asm/arch-sti*/
 ARM STM SPEAR
 #M:	Vipin Kumar <vipin.kumar@st.com>
 S:	Orphaned (Since 2016-02)
-T:	git git://git.denx.de/u-boot-stm.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-stm.git
 F:	arch/arm/cpu/arm926ejs/spear/
 F:	arch/arm/include/asm/arch-spear/
 
 ARM STM STM32MP
 M:	Patrick Delaunay <patrick.delaunay@st.com>
-M:	Christophe Kerello <christophe.kerello@st.com>
 M:	Patrice Chotard <patrice.chotard@st.com>
 L:	uboot-stm32@st-md-mailman.stormreply.com (moderated for non-subscribers)
 S:	Maintained
@@ -312,6 +312,8 @@ F:	drivers/ram/stm32mp1/
 F:	drivers/misc/stm32_rcc.c
 F:	drivers/reset/stm32-reset.c
 F:	drivers/spi/stm32_qspi.c
+F:	drivers/spi/stm32_spi.c
+F:	drivers/watchdog/stm32mp_wdt.c
 
 ARM STM STV0991
 M:	Vikas Manocha <vikas.manocha@st.com>
@@ -323,7 +325,7 @@ ARM SUNXI
 M:	Jagan Teki <jagan@amarulasolutions.com>
 M:	Maxime Ripard <maxime.ripard@bootlin.com>
 S:	Maintained
-T:	git git://git.denx.de/u-boot-sunxi.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-sunxi.git
 F:	arch/arm/cpu/armv7/sunxi/
 F:	arch/arm/include/asm/arch-sunxi/
 F:	arch/arm/mach-sunxi/
@@ -332,14 +334,14 @@ F:	board/sunxi/
 ARM TEGRA
 M:	Tom Warren <twarren@nvidia.com>
 S:	Maintained
-T:	git git://git.denx.de/u-boot-tegra.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-tegra.git
 F:	arch/arm/mach-tegra/
 F:	arch/arm/include/asm/arch-tegra*/
 
 ARM TI
 M:	Tom Rini <trini@konsulko.com>
 S:	Maintained
-T:	git git://git.denx.de/u-boot-ti.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-ti.git
 F:	arch/arm/mach-davinci/
 F:	arch/arm/mach-k3/
 F:	arch/arm/mach-keystone/
@@ -349,7 +351,7 @@ F:	arch/arm/include/asm/ti-common/
 ARM UNIPHIER
 M:	Masahiro Yamada <yamada.masahiro@socionext.com>
 S:	Maintained
-T:	git git://git.denx.de/u-boot-uniphier.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-uniphier.git
 F:	arch/arm/mach-uniphier/
 F:	configs/uniphier_*_defconfig
 N:	uniphier
@@ -357,7 +359,7 @@ N:	uniphier
 ARM VERSAL
 M:	Michal Simek <michal.simek@xilinx.com>
 S:	Maintained
-T:	git git://git.denx.de/u-boot-microblaze.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze.git
 F:	arch/arm/mach-versal/
 
 ARM VERSATILE EXPRESS DRIVERS
@@ -370,7 +372,7 @@ N:	vexpress
 ARM ZYNQ
 M:	Michal Simek <monstr@monstr.eu>
 S:	Maintained
-T:	git git://git.denx.de/u-boot-microblaze.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze.git
 F:	arch/arm/mach-zynq/
 F:	drivers/clk/clk_zynq.c
 F:	drivers/fpga/zynqpl.c
@@ -394,7 +396,7 @@ N:	zynq
 ARM ZYNQMP
 M:	Michal Simek <michal.simek@xilinx.com>
 S:	Maintained
-T:	git git://git.denx.de/u-boot-microblaze.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze.git
 F:	arch/arm/mach-zynqmp/
 F:	drivers/clk/clk_zynqmp.c
 F:	drivers/fpga/zynqpl.c
@@ -420,7 +422,7 @@ N:	zynqmp
 ARM ZYNQMP R5
 M:	Michal Simek <michal.simek@xilinx.com>
 S:	Maintained
-T:	git git://git.denx.de/u-boot-microblaze.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze.git
 F:	arch/arm/mach-zynqmp-r5/
 
 BINMAN
@@ -436,7 +438,7 @@ F:	tools/buildman/
 CFI FLASH
 M:	Stefan Roese <sr@denx.de>
 S:	Maintained
-T:	git git://git.denx.de/u-boot-cfi-flash.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-cfi-flash.git
 F:	drivers/mtd/cfi_flash.c
 F:	drivers/mtd/jedec_flash.c
 
@@ -444,13 +446,13 @@ COLDFIRE
 M:	Huan Wang <alison.wang@nxp.com>
 M:	Angelo Dureghello <angelo@sysam.it>
 S:	Maintained
-T:	git git://git.denx.de/u-boot-coldfire.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-coldfire.git
 F:	arch/m68k/
 
 DFU
 M:	Lukasz Majewski <lukma@denx.de>
 S:	Maintained
-T:	git git://git.denx.de/u-boot-dfu.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-dfu.git
 F:	cmd/dfu.c
 F:	cmd/usb_*.c
 F:	common/dfu.c
@@ -462,7 +464,7 @@ F:	drivers/usb/gadget/
 DRIVER MODEL
 M:	Simon Glass <sjg@chromium.org>
 S:	Maintained
-T:	git git://git.denx.de/u-boot-dm.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-dm.git
 F:	drivers/core/
 F:	include/dm/
 F:	test/dm/
@@ -471,10 +473,10 @@ EFI PAYLOAD
 M:	Heinrich Schuchardt <xypron.glpk@gmx.de>
 R:	Alexander Graf <agraf@csgraf.de>
 S:	Maintained
-T:	git git://git.denx.de/u-boot-efi.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-efi.git
 F:	doc/README.uefi
 F:	doc/README.iscsi
-F:	Documentation/efi.rst
+F:	doc/efi.rst
 F:	include/capitalization.h
 F:	include/charset.h
 F:	include/cp1250.h
@@ -494,7 +496,7 @@ F:	tools/file2include.c
 FPGA
 M:	Michal Simek <michal.simek@xilinx.com>
 S:	Maintained
-T:	git git://git.denx.de/u-boot-microblaze.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze.git
 F:	drivers/fpga/
 F:	cmd/fpga.c
 F:	include/fpga.h
@@ -502,7 +504,7 @@ F:	include/fpga.h
 FLATTENED DEVICE TREE
 M:	Simon Glass <sjg@chromium.org>
 S:	Maintained
-T:	git git://git.denx.de/u-boot-fdt.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-fdt.git
 F:	lib/fdtdec*
 F:	lib/libfdt/
 F:	include/fdt*
@@ -513,24 +515,24 @@ F:	common/fdt_support.c
 FREEBSD
 M:	Rafal Jaworowski <raj@semihalf.com>
 S:	Maintained
-T:	git git://git.denx.de/u-boot-freebsd.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-freebsd.git
 
 FREESCALE QORIQ
 M:	Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
 S:	Maintained
-T:	git git://git.denx.de/u-boot-fsl-qoriq.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq.git
 F:	drivers/watchdog/sp805_wdt.c
 
 I2C
 M:	Heiko Schocher <hs@denx.de>
 S:	Maintained
-T:	git git://git.denx.de/u-boot-i2c.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-i2c.git
 F:	drivers/i2c/
 
 LOGGING
 M:	Simon Glass <sjg@chromium.org>
 S:	Maintained
-T:	git git://git.denx.de/u-boot.git
+T:	git https://gitlab.denx.de/u-boot/u-boot.git
 F:	common/log.c
 F:	cmd/log.c
 F:	test/log/log_test.c
@@ -546,7 +548,7 @@ F:	drivers/i2c/i2c-versatile.c
 MICROBLAZE
 M:	Michal Simek <monstr@monstr.eu>
 S:	Maintained
-T:	git git://git.denx.de/u-boot-microblaze.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze.git
 F:	arch/microblaze/
 F:	cmd/mfsl.c
 F:	drivers/gpio/xilinx_gpio.c
@@ -561,7 +563,7 @@ N:	xilinx
 MIPS
 M:	Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
 S:	Maintained
-T:	git git://git.denx.de/u-boot-mips.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-mips.git
 F:	arch/mips/
 
 MIPS MSCC
@@ -592,38 +594,38 @@ F:	arch/mips/mach-jz47xx/
 MMC
 M:	Peng Fan <peng.fan@nxp.com>
 S:	Maintained
-T:	git git://git.denx.de/u-boot-mmc.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-mmc.git
 F:	drivers/mmc/
 
 NAND FLASH
 #M:	Scott Wood <oss@buserror.net>
 S:	Orphaned (Since 2018-07)
-T:	git git://git.denx.de/u-boot-nand-flash.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-nand-flash.git
 F:	drivers/mtd/nand/raw/
 
 NDS32
 M:	Macpaul Lin <macpaul@andestech.com>
 S:	Maintained
-T:	git git://git.denx.de/u-boot-nds32.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-nds32.git
 F:	arch/nds32/
 
 NETWORK
 M:	Joe Hershberger <joe.hershberger@ni.com>
 S:	Maintained
-T:	git git://git.denx.de/u-boot-net.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-net.git
 F:	drivers/net/
 F:	net/
 
 NIOS
 M:	Thomas Chou <thomas@wytron.com.tw>
 S:	Maintained
-T:	git git://git.denx.de/u-boot-nios.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-nios.git
 F:	arch/nios2/
 
 ONENAND
 #M:	Lukasz Majewski <l.majewski@majess.pl>
 S:	Orphaned (Since 2017-01)
-T:	git git://git.denx.de/u-boot-onenand.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-onenand.git
 F:	drivers/mtd/onenand/
 
 PATMAN
@@ -634,7 +636,7 @@ F:	tools/patman/
 POWER
 M:	Jaehoon Chung <jh80.chung@samsung.com>
 S:	Maintained
-T:	git git://git.denx.de/u-boot-pmic.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-pmic.git
 F:	drivers/power/
 
 POWERPC
@@ -645,13 +647,13 @@ F:	arch/powerpc/
 POWERPC MPC8XX
 M:	Christophe Leroy <christophe.leroy@c-s.fr>
 S:	Maintained
-T:	git git://git.denx.de/u-boot-mpc8xx.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-mpc8xx.git
 F:	arch/powerpc/cpu/mpc8xx/
 
 POWERPC MPC83XX
 M:	Mario Six <mario.six@gdsys.cc>
 S:	Maintained
-T:	git git://git.denx.de/u-boot-mpc83xx.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-mpc83xx.git
 F:	drivers/ram/mpc83xx_sdram.c
 F:	include/dt-bindings/memory/mpc83xx-sdram.h
 F:	drivers/sysreset/sysreset_mpc83xx.c
@@ -669,19 +671,19 @@ F:	arch/powerpc/include/asm/arch-mpc83xx/
 POWERPC MPC85XX
 M:	Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
 S:	Maintained
-T:	git git://git.denx.de/u-boot-mpc85xx.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-mpc85xx.git
 F:	arch/powerpc/cpu/mpc85xx/
 
 POWERPC MPC86XX
 M:	Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
 S:	Maintained
-T:	git git://git.denx.de/u-boot-mpc86xx.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-mpc86xx.git
 F:	arch/powerpc/cpu/mpc86xx/
 
 RISC-V
 M:	Rick Chen <rick@andestech.com>
 S:	Maintained
-T:	git git://git.denx.de/u-boot-riscv.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-riscv.git
 F:	arch/riscv/
 F:	cmd/riscv/
 F:	tools/prelink-riscv.c
@@ -699,15 +701,16 @@ S:	Maintained
 F:	arch/sandbox/
 
 SH
+M:	Marek Vasut <marek.vasut+renesas@gmail.com>
 M:	Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
 S:	Maintained
-T:	git git://git.denx.de/u-boot-sh.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-sh.git
 F:	arch/sh/
 
 SPI
 M:	Jagan Teki <jagan@amarulasolutions.com>
 S:	Maintained
-T:	git git://git.denx.de/u-boot-spi.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-spi.git
 F:	drivers/spi/
 F:	include/spi*
 
@@ -769,25 +772,25 @@ UBI
 M:	Kyungmin Park <kmpark@infradead.org>
 M:	Heiko Schocher <hs@denx.de>
 S:	Maintained
-T:	git git://git.denx.de/u-boot-ubi.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-ubi.git
 F:	drivers/mtd/ubi/
 
 USB
 M:	Marek Vasut <marex@denx.de>
 S:	Maintained
-T:	git git://git.denx.de/u-boot-usb.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-usb.git
 F:	drivers/usb/
 
 USB xHCI
 M:	Bin Meng <bmeng.cn@gmail.com>
 S:	Maintained
-T:	git git://git.denx.de/u-boot-usb.git topic-xhci
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-usb.git topic-xhci
 F:	drivers/usb/host/xhci*
 
 VIDEO
 M:	Anatolij Gustschin <agust@denx.de>
 S:	Maintained
-T:	git git://git.denx.de/u-boot-video.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-video.git
 F:	drivers/video/
 F:	common/lcd*.c
 F:	include/lcd*.h
@@ -797,7 +800,7 @@ X86
 M:	Simon Glass <sjg@chromium.org>
 M:	Bin Meng <bmeng.cn@gmail.com>
 S:	Maintained
-T:	git git://git.denx.de/u-boot-x86.git
+T:	git https://gitlab.denx.de/u-boot/custodians/u-boot-x86.git
 F:	arch/x86/
 F:	cmd/x86/
 
@@ -811,7 +814,7 @@ M:	Tom Rini <trini@konsulko.com>
 L:	u-boot@lists.denx.de
 Q:	http://patchwork.ozlabs.org/project/uboot/list/
 S:	Maintained
-T:	git git://git.denx.de/u-boot.git
+T:	git https://gitlab.denx.de/u-boot/u-boot.git
 F:	configs/tools-only_defconfig
 F:	*
 F:	*/

Makefile

@@ -3,7 +3,7 @@
 VERSION = 2019
 PATCHLEVEL = 07
 SUBLEVEL =
-EXTRAVERSION = -rc3
+EXTRAVERSION =
 NAME =
 
 # *DOCUMENTATION*
@@ -168,7 +168,7 @@ MAKEFLAGS += --no-print-directory
 # Use 'make C=2' to enable checking of *all* source files, regardless
 # of whether they are re-compiled or not.
 #
-# See the file "Documentation/sparse.txt" for more details, including
+# See the file "doc/sparse.txt" for more details, including
 # where to get the "sparse" utility.
 
 ifeq ("$(origin C)", "command line")
@@ -337,6 +337,19 @@ endif
 #  KBUILD_MODULES := 1
 #endif
 
+define size_check
+	actual=$$( wc -c $1 | awk '{print $$1}'); \
+	limit=$$( printf "%d" $2 ); \
+	if test $$actual -gt $$limit; then \
+		echo "$1 exceeds file size limit:" >&2; \
+		echo "  limit:  $$limit bytes" >&2; \
+		echo "  actual: $$actual bytes" >&2; \
+		echo "  excess: $$((actual - limit)) bytes" >&2; \
+		exit 1; \
+	fi
+endef
+export size_check
+
 export KBUILD_MODULES KBUILD_BUILTIN
 export KBUILD_CHECKSRC KBUILD_SRC KBUILD_EXTMOD
 
@@ -778,20 +791,17 @@ LDPPFLAGS += \
 #########################################################################
 
 ifneq ($(CONFIG_BOARD_SIZE_LIMIT),)
-BOARD_SIZE_CHECK = \
-	@actual=`wc -c $@ | awk '{print $$1}'`; \
-	limit=`printf "%d" $(CONFIG_BOARD_SIZE_LIMIT)`; \
-	if test $$actual -gt $$limit; then \
-		echo "$@ exceeds file size limit:" >&2 ; \
-		echo "  limit:  $$limit bytes" >&2 ; \
-		echo "  actual: $$actual bytes" >&2 ; \
-		echo "  excess: $$((actual - limit)) bytes" >&2; \
-		exit 1; \
-	fi
+BOARD_SIZE_CHECK= @ $(call size_check,$@,$(CONFIG_BOARD_SIZE_LIMIT))
 else
 BOARD_SIZE_CHECK =
 endif
 
+ifneq ($(CONFIG_SPL_SIZE_LIMIT),0)
+SPL_SIZE_CHECK = @$(call size_check,$@,$$(tools/spl_size_limit))
+else
+SPL_SIZE_CHECK =
+endif
+
 # Statically apply RELA-style relocations (currently arm64 only)
 # This is useful for arm64 where static relocation needs to be performed on
 # the raw binary, but certain simulators only accept an ELF file (but don't
@@ -918,6 +928,14 @@ cmd_cfgcheck = $(srctree)/scripts/check-config.sh $2 \
 		$(srctree)/scripts/config_whitelist.txt $(srctree)
 
 all:		$(ALL-y)
+ifeq ($(CONFIG_DEPRECATED),y)
+	$(warning "You have deprecated configuration options enabled in your .config! Please check your configuration.")
+ifeq ($(CONFIG_SPI),y)
+ifneq ($(CONFIG_DM_SPI)$(CONFIG_OF_CONTROL),yy)
+	$(warning "The relevant config item with associated code will remove in v2019.07 release.")
+endif
+endif
+endif
 ifeq ($(CONFIG_DM_I2C_COMPAT)$(CONFIG_SANDBOX),y)
 	@echo >&2 "===================== WARNING ======================"
 	@echo >&2 "This board uses CONFIG_DM_I2C_COMPAT. Please remove"
@@ -994,17 +1012,6 @@ ifeq ($(CONFIG_OF_EMBED),y)
 	@echo >&2 "See doc/README.fdt-control for more info."
 	@echo >&2 "===================================================="
 endif
-ifeq ($(CONFIG_SPI),y)
-ifneq ($(CONFIG_DM_SPI)$(CONFIG_OF_CONTROL),yy)
-	@echo >&2 "===================== WARNING ======================"
-	@echo >&2 "This board does not use CONFIG_DM_SPI. Please update"
-	@echo >&2 "the board before v2019.04 for no dm conversion"
-	@echo >&2 "and v2019.07 for partially dm converted drivers."
-	@echo >&2 "Failure to update can lead to driver/board removal"
-	@echo >&2 "See doc/driver-model/MIGRATION.txt for more info."
-	@echo >&2 "===================================================="
-endif
-endif
 ifeq ($(CONFIG_SPI_FLASH),y)
 ifneq ($(CONFIG_DM_SPI_FLASH)$(CONFIG_OF_CONTROL),yy)
 	@echo >&2 "===================== WARNING ======================"
@@ -1077,6 +1084,10 @@ endif
 
 u-boot.bin: u-boot-fit-dtb.bin FORCE
 	$(call if_changed,copy)
+
+u-boot-dtb.bin: u-boot-nodtb.bin dts/dt.dtb FORCE
+	$(call if_changed,cat)
+
 else ifeq ($(CONFIG_OF_SEPARATE),y)
 u-boot-dtb.bin: u-boot-nodtb.bin dts/dt.dtb FORCE
 	$(call if_changed,cat)
@@ -1090,6 +1101,7 @@ endif
 
 %.imx: %.bin
 	$(Q)$(MAKE) $(build)=arch/arm/mach-imx $@
+	$(BOARD_SIZE_CHECK)
 
 %.vyb: %.imx
 	$(Q)$(MAKE) $(build)=arch/arm/cpu/armv7/vf610 $@
@@ -1707,6 +1719,8 @@ u-boot.lds: $(LDSCRIPT) prepare FORCE
 
 spl/u-boot-spl.bin: spl/u-boot-spl
 	@:
+	$(SPL_SIZE_CHECK)
+
 spl/u-boot-spl: tools prepare \
 		$(if $(CONFIG_OF_SEPARATE)$(CONFIG_OF_EMBED)$(CONFIG_SPL_OF_PLATDATA),dts/dt.dtb) \
 		$(if $(CONFIG_OF_SEPARATE)$(CONFIG_OF_EMBED)$(CONFIG_TPL_OF_PLATDATA),dts/dt.dtb)
@@ -1769,6 +1783,7 @@ checkarmreloc: u-boot
 envtools: scripts_basic $(version_h) $(timestamp_h)
 	$(Q)$(MAKE) $(build)=tools/env
 
+tools-only: export TOOLS_ONLY=y
 tools-only: scripts_basic $(version_h) $(timestamp_h)
 	$(Q)$(MAKE) $(build)=tools
 
@@ -1832,7 +1847,8 @@ clean: $(clean-dirs)
 		-o -name modules.builtin -o -name '.tmp_*.o.*' \
 		-o -name 'dsdt.aml' -o -name 'dsdt.asl.tmp' -o -name 'dsdt.c' \
 		-o -name '*.efi' -o -name '*.gcno' -o -name '*.so' \) \
-		-type f -print | xargs rm -f
+		-type f -print | xargs rm -f \
+		bl31.c bl31.elf bl31_*.bin image.map
 
 # mrproper - Delete all generated files, including .config
 #
@@ -1901,7 +1917,7 @@ help:
 	@echo  '  coccicheck      - Execute static code analysis with Coccinelle'
 	@echo  ''
 	@echo  'Documentation targets:'
-	@$(MAKE) -f $(srctree)/Documentation/Makefile dochelp
+	@$(MAKE) -f $(srctree)/doc/Makefile dochelp
 	@echo  ''
 	@echo  '  make V=0|1 [targets] 0 => quiet build (default), 1 => verbose build'
 	@echo  '  make V=2   [targets] 2 => give reason for rebuild of target'
@@ -1930,7 +1946,7 @@ DOC_TARGETS := xmldocs latexdocs pdfdocs htmldocs epubdocs cleandocs \
 	       linkcheckdocs dochelp refcheckdocs
 PHONY += $(DOC_TARGETS)
 $(DOC_TARGETS): scripts_basic FORCE
-	$(Q)$(MAKE) $(build)=Documentation $@
+	$(Q)$(MAKE) $(build)=doc $@
 
 endif #ifeq ($(config-targets),1)
 endif #ifeq ($(mixed-targets),1)

README

@@ -486,10 +486,6 @@ The following options need to be configured:
 		PBI commands can be used to configure SoC before it starts the execution.
 		Please refer doc/README.pblimage for more details
 
-		CONFIG_SPL_FSL_PBL
-		It adds a target to create boot binary having SPL binary in PBI format
-		concatenated with u-boot binary.
-
 		CONFIG_SYS_FSL_DDR_BE
 		Defines the DDR controller register space as Big Endian
 
@@ -2546,9 +2542,6 @@ FIT uImage format:
 		Defines the size and behavior of the NAND that SPL uses
 		to read U-Boot
 
-		CONFIG_SPL_NAND_BOOT
-		Add support NAND boot
-
 		CONFIG_SYS_NAND_U_BOOT_OFFS
 		Location in NAND to read U-Boot from
 

arch/Kconfig

@@ -101,6 +101,7 @@ config SANDBOX
 	imply CMD_IOTRACE
 	imply CMD_LZMADEC
 	imply CMD_SATA
+	imply CMD_SF
 	imply CMD_SF_TEST
 	imply CRC32_VERIFY
 	imply FAT_WRITE
@@ -147,6 +148,7 @@ config X86
 	imply CMD_IO
 	imply CMD_IRQ
 	imply CMD_PCI
+	imply CMD_SF
 	imply CMD_SF_TEST
 	imply CMD_ZBOOT
 	imply DM_ETH

arch/arm/Kconfig

@@ -1406,14 +1406,24 @@ config TARGET_LS1046ARDB
 	  development platform that supports the QorIQ LS1046A
 	  Layerscape Architecture processor.
 
+config TARGET_LS1046AFRWY
+	bool "Support ls1046afrwy"
+	select ARCH_LS1046A
+	select ARM64
+	select ARMV8_MULTIENTRY
+	select BOARD_EARLY_INIT_F
+	select BOARD_LATE_INIT
+	select DM_SPI_FLASH if DM_SPI
+	imply SCSI
+	help
+	  Support for Freescale LS1046AFRWY platform.
+	  The LS1046A Freeway Board (FRWY) is a high-performance
+	  development platform that supports the QorIQ LS1046A
+	  Layerscape Architecture processor.
 config TARGET_H2200
 	bool "Support h2200"
 	select CPU_PXA
 
-config TARGET_ZIPITZ2
-	bool "Support zipitz2"
-	select CPU_PXA
-
 config TARGET_COLIBRI_PXA270
 	bool "Support colibri_pxa270"
 	select CPU_PXA
@@ -1697,6 +1707,7 @@ source "board/freescale/ls1021aiot/Kconfig"
 source "board/freescale/ls1046aqds/Kconfig"
 source "board/freescale/ls1043ardb/Kconfig"
 source "board/freescale/ls1046ardb/Kconfig"
+source "board/freescale/ls1046afrwy/Kconfig"
 source "board/freescale/ls1012aqds/Kconfig"
 source "board/freescale/ls1012ardb/Kconfig"
 source "board/freescale/ls1012afrdm/Kconfig"
@@ -1727,7 +1738,6 @@ source "board/woodburn/Kconfig"
 source "board/xilinx/Kconfig"
 source "board/xilinx/zynq/Kconfig"
 source "board/xilinx/zynqmp/Kconfig"
-source "board/zipitz2/Kconfig"
 
 source "arch/arm/Kconfig.debug"
 

arch/arm/cpu/armv8/Kconfig

@@ -107,6 +107,7 @@ config PSCI_RESET
 		   !TARGET_LS1028ARDB && !TARGET_LS1028AQDS && \
 		   !TARGET_LS1043ARDB && !TARGET_LS1043AQDS && \
 		   !TARGET_LS1046ARDB && !TARGET_LS1046AQDS && \
+		   !TARGET_LS1046AFRWY && \
 		   !TARGET_LS2081ARDB && !TARGET_LX2160ARDB && \
 		   !TARGET_LX2160AQDS && \
 		   !ARCH_UNIPHIER && !TARGET_S32V234EVB

arch/arm/cpu/armv8/fsl-layerscape/Kconfig

@@ -48,6 +48,7 @@ config ARCH_LS1028A
 	select SYS_I2C_MXC_I2C6
 	select SYS_I2C_MXC_I2C7
 	select SYS_I2C_MXC_I2C8
+	select SYS_FSL_ERRATUM_A008997
 	select SYS_FSL_ERRATUM_A009007
 	select SYS_FSL_ERRATUM_A008514 if !TFABOOT
 	select SYS_FSL_ERRATUM_A009663 if !TFABOOT

arch/arm/cpu/armv8/fsl-layerscape/fdt.c

@@ -435,7 +435,7 @@ void ft_cpu_setup(void *blob, bd_t *bd)
 	do_fixup_by_path_u32(blob, "/sysclk", "clock-frequency",
 			     CONFIG_SYS_CLK_FREQ, 1);
 
-#ifdef CONFIG_PCI
+#ifdef CONFIG_PCI_LAYERSCAPE
 	ft_pci_setup(blob, bd);
 #endif
 

arch/arm/cpu/armv8/fsl-layerscape/fsl_lsch2_speed.c

@@ -1,6 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0+
 /*
  * Copyright 2015 Freescale Semiconductor, Inc.
+ * Copyright 2019 NXP.
  */
 
 #include <common.h>
@@ -250,6 +251,7 @@ unsigned int mxc_get_clock(enum mxc_clock clk)
 		return get_i2c_freq(0);
 #if defined(CONFIG_FSL_ESDHC)
 	case MXC_ESDHC_CLK:
+	case MXC_ESDHC2_CLK:
 		return get_sdhc_freq(0);
 #endif
 	case MXC_DSPI_CLK:

arch/arm/cpu/armv8/fsl-layerscape/fsl_lsch3_speed.c

@@ -1,6 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0+
 /*
  * Copyright 2014-2015, Freescale Semiconductor, Inc.
+ * Copyright 2019 NXP Semiconductors
  *
  * Derived from arch/power/cpu/mpc85xx/speed.c
  */
@@ -214,6 +215,7 @@ unsigned int mxc_get_clock(enum mxc_clock clk)
 		return get_i2c_freq(0);
 #if defined(CONFIG_FSL_ESDHC)
 	case MXC_ESDHC_CLK:
+	case MXC_ESDHC2_CLK:
 		return get_sdhc_freq(0);
 #endif
 	case MXC_DSPI_CLK:

arch/arm/cpu/armv8/fsl-layerscape/lowlevel.S

@@ -1,6 +1,7 @@
 /* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * (C) Copyright 2014-2015 Freescale Semiconductor
+ * Copyright 2019 NXP
  *
  * Extracted from armv8/start.S
  */
@@ -356,31 +357,22 @@ get_svr:
 
 #if defined(CONFIG_SYS_FSL_HAS_CCN504) || defined(CONFIG_SYS_FSL_HAS_CCN508)
 hnf_pstate_poll:
-	/* x0 has the desired status, return 0 for success, 1 for timeout
-	 * clobber x1, x2, x3, x4, x6, x7
+	/* x0 has the desired status, return only if operation succeed
+	 * clobber x1, x2, x6
 	 */
 	mov	x1, x0
-	mov	x7, #0			/* flag for timeout */
-	mrs	x3, cntpct_el0		/* read timer */
-	add	x3, x3, #1200		/* timeout after 100 microseconds */
+	mov	w6, #8			/* HN-F node count */
 	mov	x0, #0x18
 	movk	x0, #0x420, lsl #16	/* HNF0_PSTATE_STATUS */
-	mov	w6, #8			/* HN-F node count */
 1:
 	ldr	x2, [x0]
 	cmp	x2, x1			/* check status */
 	b.eq	2f
-	mrs	x4, cntpct_el0
-	cmp	x4, x3
-	b.ls	1b
-	mov	x7, #1			/* timeout */
-	b	3f
+	b	1b
 2:
 	add	x0, x0, #0x10000	/* move to next node */
 	subs	w6, w6, #1
 	cbnz	w6, 1b
-3:
-	mov	x0, x7
 	ret
 
 hnf_set_pstate:
@@ -405,10 +397,8 @@ ENTRY(__asm_flush_l3_dcache)
 	/*
 	 * Return status in x0
 	 *    success 0
-	 *    timeout 1 for setting SFONLY, 2 for FAM, 3 for both
 	 */
 	mov	x29, lr
-	mov	x8, #0
 
 	dsb	sy
 	mov	x0, #0x1		/* HNFPSTAT_SFONLY */
@@ -416,19 +406,15 @@ ENTRY(__asm_flush_l3_dcache)
 
 	mov	x0, #0x4		/* SFONLY status */
 	bl	hnf_pstate_poll
-	cbz	x0, 1f
-	mov	x8, #1			/* timeout */
-1:
+
 	dsb	sy
 	mov	x0, #0x3		/* HNFPSTAT_FAM */
 	bl	hnf_set_pstate
 
 	mov	x0, #0xc		/* FAM status */
 	bl	hnf_pstate_poll
-	cbz	x0, 1f
-	add	x8, x8, #0x2
-1:
-	mov	x0, x8
+
+	mov	x0, #0
 	mov	lr, x29
 	ret
 ENDPROC(__asm_flush_l3_dcache)

arch/arm/cpu/armv8/fsl-layerscape/ls1028a_serdes.c

@@ -22,6 +22,19 @@ static struct serdes_config serdes1_cfg_tbl[] = {
 	{0xEBCC, {PCIE1, PCIE1, PCIE2, SATA1} },
 	{0xCCCC, {PCIE1, PCIE1, PCIE2, PCIE2} },
 	{0xDDDD, {PCIE1, PCIE1, PCIE1, PCIE1} },
+	{0xE031, {SXGMII1, QXGMII2, NONE, SATA1} },
+	{0xB991, {SXGMII1, SGMII1, SGMII2, PCIE1} },
+	{0xBB31, {SXGMII1, QXGMII2, PCIE1, PCIE1} },
+	{0xCC31, {SXGMII1, QXGMII2, PCIE2, PCIE2} },
+	{0xBB51, {SXGMII1, QSGMII_B, PCIE2, PCIE1} },
+	{0xBB38, {SGMII_T1, QXGMII2, PCIE2, PCIE1} },
+	{0xCC38, {SGMII_T1, QXGMII2, PCIE2, PCIE2} },
+	{0xBB58, {SGMII_T1, QSGMII_B, PCIE2, PCIE1} },
+	{0xCC58, {SGMII_T1, QSGMII_B, PCIE2, PCIE2} },
+	{0xCC8B, {PCIE1, SGMII_T1, PCIE2, PCIE2} },
+	{0xEB58, {SGMII_T1, QSGMII_B, PCIE2, SATA1} },
+	{0xEB8B, {PCIE1, SGMII_T1, PCIE2, SATA1} },
+	{0xE8CC, {PCIE1, PCIE1, SGMII_T1, SATA1} },
 	{}
 };
 

arch/arm/cpu/armv8/fsl-layerscape/ls1046a_serdes.c

@@ -1,6 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0+
 /*
  * Copyright 2016 Freescale Semiconductor, Inc.
+ * Copyright 2019 NXP
  */
 
 #include <common.h>
@@ -29,10 +30,11 @@ static struct serdes_config serdes1_cfg_tbl[] = {
 	{0x1163, {XFI_FM1_MAC9, XFI_FM1_MAC10, PCIE1, SGMII_FM1_DTSEC6} },
 	{0x2263, {SGMII_2500_FM1_DTSEC9, SGMII_2500_FM1_DTSEC10, PCIE1,
 		  SGMII_FM1_DTSEC6} },
-	{0x3363, {SGMII_FM1_DTSEC5, SGMII_FM1_DTSEC6, PCIE1,
+	{0x3363, {SGMII_FM1_DTSEC9, SGMII_FM1_DTSEC10, PCIE1,
 		  SGMII_FM1_DTSEC6} },
 	{0x2223, {SGMII_2500_FM1_DTSEC9, SGMII_2500_FM1_DTSEC10,
 		  SGMII_2500_FM1_DTSEC5, SGMII_FM1_DTSEC6} },
+	{0x3040, {SGMII_FM1_DTSEC9, NONE, QSGMII_FM1_A, NONE} },
 	{}
 };
 

arch/arm/cpu/armv8/fsl-layerscape/soc.c

@@ -1,6 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0+
 /*
  * Copyright 2014-2015 Freescale Semiconductor
+ * Copyright 2019 NXP
  */
 
 #include <common.h>
@@ -126,6 +127,10 @@ static void erratum_a008997(void)
 	set_usb_pcstxswingfull(scfg, SCFG_USB3PRM2CR_USB2);
 	set_usb_pcstxswingfull(scfg, SCFG_USB3PRM2CR_USB3);
 #endif
+#elif defined(CONFIG_ARCH_LS1028A)
+	clrsetbits_le32(DCSR_BASE +  DCSR_USB_IOCR1,
+			0x7F << 11,
+			DCSR_USB_PCSTXSWINGFULL << 11);
 #endif
 #endif /* CONFIG_SYS_FSL_ERRATUM_A008997 */
 }
@@ -139,7 +144,8 @@ static void erratum_a008997(void)
 	out_be16((phy) + SCFG_USB_PHY_RX_OVRD_IN_HI, USB_PHY_RX_EQ_VAL_3);	\
 	out_be16((phy) + SCFG_USB_PHY_RX_OVRD_IN_HI, USB_PHY_RX_EQ_VAL_4)
 
-#elif defined(CONFIG_ARCH_LS2080A) || defined(CONFIG_ARCH_LS1088A)
+#elif defined(CONFIG_ARCH_LS2080A) || defined(CONFIG_ARCH_LS1088A) || \
+	defined(CONFIG_ARCH_LS1028A)
 
 #define PROGRAM_USB_PHY_RX_OVRD_IN_HI(phy)	\
 	out_le16((phy) + DCSR_USB_PHY_RX_OVRD_IN_HI, USB_PHY_RX_EQ_VAL_1); \
@@ -163,7 +169,8 @@ static void erratum_a009007(void)
 	usb_phy = (void __iomem *)SCFG_USB_PHY3;
 	PROGRAM_USB_PHY_RX_OVRD_IN_HI(usb_phy);
 #endif
-#elif defined(CONFIG_ARCH_LS2080A) || defined(CONFIG_ARCH_LS1088A)
+#elif defined(CONFIG_ARCH_LS2080A) || defined(CONFIG_ARCH_LS1088A) || \
+	defined(CONFIG_ARCH_LS1028A)
 	void __iomem *dcsr = (void __iomem *)DCSR_BASE;
 
 	PROGRAM_USB_PHY_RX_OVRD_IN_HI(dcsr + DCSR_USB_PHY1);
@@ -593,6 +600,9 @@ void fsl_lsch2_early_init_f(void)
 	struct ccsr_cci400 *cci = (struct ccsr_cci400 *)(CONFIG_SYS_IMMR +
 					CONFIG_SYS_CCI400_OFFSET);
 	struct ccsr_scfg *scfg = (struct ccsr_scfg *)CONFIG_SYS_FSL_SCFG_ADDR;
+#if defined(CONFIG_FSL_QSPI) && defined(CONFIG_TFABOOT)
+	enum boot_src src;
+#endif
 
 #ifdef CONFIG_LAYERSCAPE_NS_ACCESS
 	enable_layerscape_ns_access();
@@ -602,8 +612,14 @@ void fsl_lsch2_early_init_f(void)
 	init_early_memctl_regs();	/* tighten IFC timing */
 #endif
 
+#if defined(CONFIG_FSL_QSPI) && defined(CONFIG_TFABOOT)
+	src = get_boot_src();
+	if (src != BOOT_SOURCE_QSPI_NOR)
+		out_be32(&scfg->qspi_cfg, SCFG_QSPI_CLKSEL);
+#else
 #if defined(CONFIG_FSL_QSPI) && !defined(CONFIG_QSPI_BOOT)
 	out_be32(&scfg->qspi_cfg, SCFG_QSPI_CLKSEL);
+#endif
 #endif
 	/* Make SEC reads and writes snoopable */
 	setbits_be32(&scfg->snpcnfgcr, SCFG_SNPCNFGCR_SECRDSNP |
@@ -808,7 +824,11 @@ int board_late_init(void)
 	 * check if gd->env_addr is default_environment; then setenv bootcmd
 	 * and mcinitcmd.
 	 */
+#if !defined(CONFIG_ENV_ADDR) || defined(ENV_IS_EMBEDDED)
+	if (gd->env_addr == (ulong)&default_environment[0]) {
+#else
 	if (gd->env_addr + gd->reloc_off == (ulong)&default_environment[0]) {
+#endif
 		fsl_setenv_bootcmd();
 		fsl_setenv_mcinitcmd();
 	}

arch/arm/cpu/armv8/start.S

@@ -18,7 +18,7 @@
 
 .globl	_start
 _start:
-#if defined(LINUX_KERNEL_IMAGE_HEADER)
+#if defined(CONFIG_LINUX_KERNEL_IMAGE_HEADER)
 #include <asm/boot0-linux-kernel-header.h>
 #elif defined(CONFIG_ENABLE_ARM_SOC_BOOT0_HOOK)
 /*

arch/arm/dts/Makefile

@@ -93,7 +93,8 @@ dtb-$(CONFIG_ROCKCHIP_RK3288) += \
 	rk3288-vyasa.dtb
 
 dtb-$(CONFIG_ROCKCHIP_RK3328) += \
-	rk3328-evb.dtb
+	rk3328-evb.dtb \
+	rk3328-rock64.dtb
 
 dtb-$(CONFIG_ROCKCHIP_RK3368) += \
 	rk3368-lion.dtb \
@@ -108,11 +109,14 @@ dtb-$(CONFIG_ROCKCHIP_RK3399) += \
 	rk3399-gru-bob.dtb \
 	rk3399-nanopc-t4.dtb \
 	rk3399-nanopi-m4.dtb \
+	rk3399-nanopi-neo4.dtb \
 	rk3399-orangepi.dtb \
 	rk3399-puma-ddr1333.dtb \
 	rk3399-puma-ddr1600.dtb \
 	rk3399-puma-ddr1866.dtb \
+	rk3399-rock-pi-4.dtb \
 	rk3399-rock960.dtb \
+	rk3399-rockpro64.dtb
 
 dtb-$(CONFIG_ROCKCHIP_RV1108) += \
 	rv1108-elgin-r1.dtb \
@@ -339,6 +343,7 @@ dtb-$(CONFIG_FSL_LSCH2) += fsl-ls1043a-qds-duart.dtb \
 	fsl-ls1046a-qds-duart.dtb \
 	fsl-ls1046a-qds-lpuart.dtb \
 	fsl-ls1046a-rdb.dtb \
+	fsl-ls1046a-frwy.dtb \
 	fsl-ls1012a-qds.dtb \
 	fsl-ls1012a-rdb.dtb \
 	fsl-ls1012a-2g5rdb.dtb \
@@ -532,14 +537,14 @@ dtb-$(CONFIG_VF610) += vf500-colibri.dtb \
 	vf610-bk4r1.dtb
 
 dtb-$(CONFIG_MX53) += imx53-cx9020.dtb \
-	imx53-kp.dtb
+	imx53-kp.dtb \
+	imx53-m53menlo.dtb
 
 dtb-$(CONFIG_MX6Q) += \
 	imx6-apalis.dtb \
 	imx6q-display5.dtb \
-	imx6q-logicpd.dtb
-
-dtb-$(CONFIG_TARGET_TBS2910) += \
+	imx6q-logicpd.dtb \
+	imx6q-novena.dtb \
 	imx6q-tbs2910.dtb
 
 dtb-$(CONFIG_MX6QDL) += \
@@ -547,19 +552,19 @@ dtb-$(CONFIG_MX6QDL) += \
 	imx6dl-icore-mipi.dtb \
 	imx6dl-icore-rqs.dtb \
 	imx6dl-mamoj.dtb \
+	imx6dl-sabreauto.dtb \
+	imx6dl-sabresd.dtb \
+	imx6dl-wandboard-revb1.dtb \
 	imx6q-cm-fx6.dtb \
 	imx6q-icore.dtb \
 	imx6q-icore-mipi.dtb \
 	imx6q-icore-rqs.dtb \
 	imx6q-sabreauto.dtb \
 	imx6q-sabresd.dtb \
-	imx6dl-sabreauto.dtb \
-	imx6dl-sabresd.dtb \
+	imx6q-wandboard-revb1.dtb \
 	imx6qp-sabreauto.dtb \
-	imx6qp-sabresd.dtb
-
-dtb-$(CONFIG_TARGET_WANDBOARD) += \
-	imx6dl-wandboard-revb1.dtb
+	imx6qp-sabresd.dtb \
+	imx6qp-wandboard-revd1.dtb
 
 dtb-$(CONFIG_MX6SL) += imx6sl-evk.dtb
 
@@ -567,7 +572,8 @@ dtb-$(CONFIG_MX6SLL) += imx6sll-evk.dtb
 
 dtb-$(CONFIG_MX6SX) += \
 	imx6sx-sabreauto.dtb \
-	imx6sx-sdb.dtb
+	imx6sx-sdb.dtb \
+	imx6sx-softing-vining-2000.dtb
 
 dtb-$(CONFIG_MX6UL) += \
 	imx6ul-geam.dtb \
@@ -585,10 +591,13 @@ dtb-$(CONFIG_MX6UL) += \
 dtb-$(CONFIG_MX6ULL) += \
 	imx6ull-14x14-evk.dtb \
 	imx6ull-colibri.dtb \
+	imx6ull-phycore-segin.dtb \
 	imx6ull-dart-6ul.dtb
 
 dtb-$(CONFIG_ARCH_MX6) += \
-	imx6-colibri.dtb
+	imx6-apalis.dtb \
+	imx6-colibri.dtb \
+	imx6q-dhcom-pdk2.dtb
 
 dtb-$(CONFIG_MX7) += imx7d-sdb.dtb \
 	imx7d-sdb-qspi.dtb \
@@ -602,8 +611,10 @@ dtb-$(CONFIG_MX7) += imx7d-sdb.dtb \
 dtb-$(CONFIG_ARCH_MX7ULP) += imx7ulp-evk.dtb
 
 dtb-$(CONFIG_ARCH_IMX8) += \
-	fsl-imx8qxp-mek.dtb \
+	fsl-imx8qm-apalis.dtb \
 	fsl-imx8qm-mek.dtb \
+	fsl-imx8qxp-colibri.dtb \
+	fsl-imx8qxp-mek.dtb
 
 dtb-$(CONFIG_ARCH_IMX8M) += fsl-imx8mq-evk.dtb
 
@@ -726,14 +737,19 @@ dtb-$(CONFIG_TARGET_VINCO) += \
 	at91-vinco.dtb
 
 dtb-$(CONFIG_ARCH_BCM283X) += \
-	bcm2835-rpi-a-plus.dtb \
 	bcm2835-rpi-a.dtb \
+	bcm2835-rpi-a-plus.dtb \
+	bcm2835-rpi-b.dtb \
 	bcm2835-rpi-b-plus.dtb \
 	bcm2835-rpi-b-rev2.dtb \
-	bcm2835-rpi-b.dtb \
-	bcm2835-rpi-zero-w.dtb \
+	bcm2835-rpi-cm1-io1.dtb \
+	bcm2835-rpi-zero.dtb \
+	bcm2835-rpi-zero-w.dtb\
 	bcm2836-rpi-2-b.dtb \
-	bcm2837-rpi-3-b.dtb
+	bcm2837-rpi-3-a-plus.dtb \
+	bcm2837-rpi-3-b.dtb \
+	bcm2837-rpi-3-b-plus.dtb \
+	bcm2837-rpi-cm3-io3.dtb
 
 dtb-$(CONFIG_ARCH_BCM63158) += \
 	bcm963158.dtb
@@ -747,6 +763,7 @@ dtb-$(CONFIG_ARCH_STI) += stih410-b2260.dtb
 
 dtb-$(CONFIG_TARGET_STM32MP1) += \
 	stm32mp157a-dk1.dtb \
+	stm32mp157a-avenger96.dtb \
 	stm32mp157c-dk2.dtb \
 	stm32mp157c-ed1.dtb \
 	stm32mp157c-ev1.dtb

arch/arm/dts/armada-388-helios4-u-boot.dtsi

@@ -20,3 +20,7 @@
 	status = "okay";
 	u-boot,dm-spl;
 };
+
+&sdhci {
+       u-boot,dm-spl;
+};

arch/arm/dts/bcm2835-rpi-a-plus.dts

@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0
 /dts-v1/;
 #include "bcm2835.dtsi"
 #include "bcm2835-rpi.dtsi"
@@ -9,12 +10,12 @@
 
 	leds {
 		act {
-			gpios = <&gpio 47 0>;
+			gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
 		};
 
 		pwr {
 			label = "PWR";
-			gpios = <&gpio 35 0>;
+			gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
 			default-state = "keep";
 			linux,default-trigger = "default-on";
 		};
@@ -30,8 +31,8 @@
 	 * "FOO" = GPIO line named "FOO" on the schematic
 	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
 	 */
-	gpio-line-names = "SDA0",
-			  "SCL0",
+	gpio-line-names = "ID_SDA",
+			  "ID_SCL",
 			  "SDA1",
 			  "SCL1",
 			  "GPIO_GCLK",
@@ -100,6 +101,12 @@
 	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
 };
 
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_gpio14>;

arch/arm/dts/bcm2835-rpi-a.dts

@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0
 /dts-v1/;
 #include "bcm2835.dtsi"
 #include "bcm2835-rpi.dtsi"
@@ -9,7 +10,7 @@
 
 	leds {
 		act {
-			gpios = <&gpio 16 1>;
+			gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
 		};
 	};
 };
@@ -95,6 +96,12 @@
 	hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
 };
 
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_gpio14>;

arch/arm/dts/bcm2835-rpi-b-plus.dts

@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0
 /dts-v1/;
 #include "bcm2835.dtsi"
 #include "bcm2835-rpi.dtsi"
@@ -10,12 +11,12 @@
 
 	leds {
 		act {
-			gpios = <&gpio 47 0>;
+			gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
 		};
 
 		pwr {
 			label = "PWR";
-			gpios = <&gpio 35 0>;
+			gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
 			default-state = "keep";
 			linux,default-trigger = "default-on";
 		};
@@ -32,8 +33,8 @@
 	 * "FOO" = GPIO line named "FOO" on the schematic
 	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
 	 */
-	gpio-line-names = "SDA0",
-			  "SCL0",
+	gpio-line-names = "ID_SDA",
+			  "ID_SCL",
 			  "SDA1",
 			  "SCL1",
 			  "GPIO_GCLK",
@@ -102,6 +103,12 @@
 	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
 };
 
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_gpio14>;

arch/arm/dts/bcm2835-rpi-b-rev2.dts

@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0
 /dts-v1/;
 #include "bcm2835.dtsi"
 #include "bcm2835-rpi.dtsi"
@@ -10,7 +11,7 @@
 
 	leds {
 		act {
-			gpios = <&gpio 16 1>;
+			gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
 		};
 	};
 };
@@ -92,7 +93,13 @@
 };
 
 &hdmi {
-	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
+	status = "okay";
 };
 
 &uart0 {

arch/arm/dts/bcm2835-rpi-b.dts

@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0
 /dts-v1/;
 #include "bcm2835.dtsi"
 #include "bcm2835-rpi.dtsi"
@@ -10,7 +11,7 @@
 
 	leds {
 		act {
-			gpios = <&gpio 16 1>;
+			gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
 		};
 	};
 };
@@ -90,6 +91,12 @@
 	hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
 };
 
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_gpio14>;

arch/arm/dts/bcm2835-rpi-cm1-io1.dts

@@ -0,0 +1,88 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2835-rpi-cm1.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
+
+/ {
+	compatible = "raspberrypi,compute-module", "brcm,bcm2835";
+	model = "Raspberry Pi Compute Module IO board rev1";
+};
+
+&gpio {
+	/*
+	 * This is based on the official GPU firmware DT blob.
+	 *
+	 * Legend:
+	 * "NC" = not connected (no rail from the SoC)
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "GPIO0",
+			  "GPIO1",
+			  "GPIO2",
+			  "GPIO3",
+			  "GPIO4",
+			  "GPIO5",
+			  "GPIO6",
+			  "GPIO7",
+			  "GPIO8",
+			  "GPIO9",
+			  "GPIO10",
+			  "GPIO11",
+			  "GPIO12",
+			  "GPIO13",
+			  "GPIO14",
+			  "GPIO15",
+			  "GPIO16",
+			  "GPIO17",
+			  "GPIO18",
+			  "GPIO19",
+			  "GPIO20",
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "GPIO26",
+			  "GPIO27",
+			  "GPIO28",
+			  "GPIO29",
+			  "GPIO30",
+			  "GPIO31",
+			  "GPIO32",
+			  "GPIO33",
+			  "GPIO34",
+			  "GPIO35",
+			  "GPIO36",
+			  "GPIO37",
+			  "GPIO38",
+			  "GPIO39",
+			  "GPIO40",
+			  "GPIO41",
+			  "GPIO42",
+			  "GPIO43",
+			  "GPIO44",
+			  "GPIO45",
+			  "HDMI_HPD_N",
+			  /* Also used as ACT LED */
+			  "EMMC_EN_N",
+			  /* Used by eMMC */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+
+	pinctrl-0 = <&gpioout &alt0>;
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_gpio14>;
+	status = "okay";
+};

arch/arm/dts/bcm2835-rpi-cm1.dtsi

@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2835.dtsi"
+#include "bcm2835-rpi.dtsi"
+
+/ {
+	leds {
+		act {
+			gpios = <&gpio 47 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	reg_3v3: fixed-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_1v8: fixed-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
+};
+
+&sdhost {
+	non-removable;
+	vmmc-supply = <&reg_3v3>;
+	vqmmc-supply = <&reg_1v8>;
+};

arch/arm/dts/bcm2835-rpi-zero-w.dts

@@ -1,26 +1,135 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2017 Stefan Wahren <stefan.wahren@i2se.com>
+ */
+
 /dts-v1/;
 #include "bcm2835.dtsi"
 #include "bcm2835-rpi.dtsi"
-#include "bcm283x-rpi-smsc9512.dtsi"
-#include "bcm283x-rpi-usb-host.dtsi"
+#include "bcm283x-rpi-usb-otg.dtsi"
 
 / {
 	compatible = "raspberrypi,model-zero-w", "brcm,bcm2835";
 	model = "Raspberry Pi Zero W";
 
+	chosen {
+		/* 8250 auxiliary UART instead of pl011 */
+		stdout-path = "serial1:115200n8";
+	};
+
 	leds {
 		act {
-			gpios = <&gpio 47 0>;
+			gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
 		};
 	};
+
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio 41 GPIO_ACTIVE_LOW>;
+	};
 };
 
-&uart1 {
-    pinctrl-names = "default";
-    pinctrl-0 = <&uart1_gpio14>;
-    status = "okay";
+&gpio {
+	/*
+	 * This is based on the official GPU firmware DT blob.
+	 *
+	 * Legend:
+	 * "NC" = not connected (no rail from the SoC)
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "ID_SDA",
+			  "ID_SCL",
+			  "SDA1",
+			  "SCL1",
+			  "GPIO_GCLK",
+			  "GPIO5",
+			  "GPIO6",
+			  "SPI_CE1_N",
+			  "SPI_CE0_N",
+			  "SPI_MISO",
+			  "SPI_MOSI",
+			  "SPI_SCLK",
+			  "GPIO12",
+			  "GPIO13",
+			  /* Serial port */
+			  "TXD0",
+			  "RXD0",
+			  "GPIO16",
+			  "GPIO17",
+			  "GPIO18",
+			  "GPIO19",
+			  "GPIO20",
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "GPIO26",
+			  "GPIO27",
+			  "SDA0",
+			  "SCL0",
+			  "NC", /* GPIO30 */
+			  "NC", /* GPIO31 */
+			  "NC", /* GPIO32 */
+			  "NC", /* GPIO33 */
+			  "NC", /* GPIO34 */
+			  "NC", /* GPIO35 */
+			  "NC", /* GPIO36 */
+			  "NC", /* GPIO37 */
+			  "NC", /* GPIO38 */
+			  "NC", /* GPIO39 */
+			  "CAM_GPIO1", /* GPIO40 */
+			  "WL_ON", /* GPIO41 */
+			  "NC", /* GPIO42 */
+			  "WIFI_CLK", /* GPIO43 */
+			  "CAM_GPIO0", /* GPIO44 */
+			  "BT_ON", /* GPIO45 */
+			  "HDMI_HPD_N",
+			  "STATUS_LED_N",
+			  /* Used by SD Card */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+
+	pinctrl-0 = <&gpioout &alt0>;
 };
 
 &hdmi {
 	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
 };
+
+&sdhci {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-0 = <&emmc_gpio34 &gpclk2_gpio43>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	non-removable;
+	status = "okay";
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_gpio32 &uart0_ctsrts_gpio30>;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		max-speed = <2000000>;
+		shutdown-gpios = <&gpio 45 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_gpio14>;
+	status = "okay";
+};

arch/arm/dts/bcm2835-rpi-zero.dts

@@ -0,0 +1,105 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2016 Stefan Wahren <stefan.wahren@i2se.com>
+ */
+
+/dts-v1/;
+#include "bcm2835.dtsi"
+#include "bcm2835-rpi.dtsi"
+#include "bcm283x-rpi-usb-otg.dtsi"
+
+/ {
+	compatible = "raspberrypi,model-zero", "brcm,bcm2835";
+	model = "Raspberry Pi Zero";
+
+	leds {
+		act {
+			gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&gpio {
+	/*
+	 * This is based on the official GPU firmware DT blob.
+	 *
+	 * Legend:
+	 * "NC" = not connected (no rail from the SoC)
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "ID_SDA",
+			  "ID_SCL",
+			  "SDA1",
+			  "SCL1",
+			  "GPIO_GCLK",
+			  "GPIO5",
+			  "GPIO6",
+			  "SPI_CE1_N",
+			  "SPI_CE0_N",
+			  "SPI_MISO",
+			  "SPI_MOSI",
+			  "SPI_SCLK",
+			  "GPIO12",
+			  "GPIO13",
+			  /* Serial port */
+			  "TXD0",
+			  "RXD0",
+			  "GPIO16",
+			  "GPIO17",
+			  "GPIO18",
+			  "GPIO19",
+			  "GPIO20",
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "GPIO26",
+			  "GPIO27",
+			  "SDA0",
+			  "SCL0",
+			  "NC", /* GPIO30 */
+			  "NC", /* GPIO31 */
+			  "CAM_GPIO1", /* GPIO32 */
+			  "NC", /* GPIO33 */
+			  "NC", /* GPIO34 */
+			  "NC", /* GPIO35 */
+			  "NC", /* GPIO36 */
+			  "NC", /* GPIO37 */
+			  "NC", /* GPIO38 */
+			  "NC", /* GPIO39 */
+			  "NC", /* GPIO40 */
+			  "CAM_GPIO0", /* GPIO41 */
+			  "NC", /* GPIO42 */
+			  "NC", /* GPIO43 */
+			  "NC", /* GPIO44 */
+			  "NC", /* GPIO45 */
+			  "HDMI_HPD_N",
+			  "STATUS_LED_N",
+			  /* Used by SD Card */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+
+	pinctrl-0 = <&gpioout &alt0 &i2s_alt0>;
+
+	/* I2S interface */
+	i2s_alt0: i2s_alt0 {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <BCM2835_FSEL_ALT0>;
+	};
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_gpio14>;
+	status = "okay";
+};

arch/arm/dts/bcm2835-rpi.dtsi

@@ -1,7 +1,7 @@
 #include <dt-bindings/power/raspberrypi-power.h>
 
 / {
-	memory {
+	memory@0 {
 		device_type = "memory";
 		reg = <0 0x10000000>;
 	};
@@ -18,7 +18,7 @@
 
 	soc {
 		firmware: firmware {
-			compatible = "raspberrypi,bcm2835-firmware";
+			compatible = "raspberrypi,bcm2835-firmware", "simple-bus";
 			mboxes = <&mailbox>;
 		};
 
@@ -27,6 +27,12 @@
 			firmware = <&firmware>;
 			#power-domain-cells = <1>;
 		};
+
+		vchiq: mailbox@7e00b840 {
+			compatible = "brcm,bcm2835-vchiq";
+			reg = <0x7e00b840 0x3c>;
+			interrupts = <0 2>;
+		};
 	};
 };
 
@@ -65,30 +71,20 @@
 &sdhci {
 	pinctrl-names = "default";
 	pinctrl-0 = <&emmc_gpio48>;
-	status = "okay";
 	bus-width = <4>;
 };
 
 &sdhost {
 	pinctrl-names = "default";
 	pinctrl-0 = <&sdhost_gpio48>;
-	bus-width = <4>;
-};
-
-&pwm {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
 	status = "okay";
+	bus-width = <4>;
 };
 
 &usb {
 	power-domains = <&power RPI_POWER_DOMAIN_USB>;
 };
 
-&v3d {
-	power-domains = <&power RPI_POWER_DOMAIN_V3D>;
-};
-
 &hdmi {
 	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
 	status = "okay";

arch/arm/dts/bcm2835.dtsi

@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0
 #include "bcm283x.dtsi"
 
 / {
@@ -17,10 +18,10 @@
 	soc {
 		ranges = <0x7e000000 0x20000000 0x02000000>;
 		dma-ranges = <0x40000000 0x00000000 0x20000000>;
+	};
 
-		arm-pmu {
-			compatible = "arm,arm1176-pmu";
-		};
+	arm-pmu {
+		compatible = "arm,arm1176-pmu";
 	};
 };
 

arch/arm/dts/bcm2836-rpi-2-b.dts

@@ -1,6 +1,7 @@
+// SPDX-License-Identifier: GPL-2.0
 /dts-v1/;
 #include "bcm2836.dtsi"
-#include "bcm2835-rpi.dtsi"
+#include "bcm2836-rpi.dtsi"
 #include "bcm283x-rpi-smsc9514.dtsi"
 #include "bcm283x-rpi-usb-host.dtsi"
 
@@ -8,18 +9,18 @@
 	compatible = "raspberrypi,2-model-b", "brcm,bcm2836";
 	model = "Raspberry Pi 2 Model B";
 
-	memory {
+	memory@0 {
 		reg = <0 0x40000000>;
 	};
 
 	leds {
 		act {
-			gpios = <&gpio 47 0>;
+			gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
 		};
 
 		pwr {
 			label = "PWR";
-			gpios = <&gpio 35 0>;
+			gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
 			default-state = "keep";
 			linux,default-trigger = "default-on";
 		};
@@ -27,6 +28,72 @@
 };
 
 &gpio {
+	/*
+	 * Taken from rpi_SCH_2b_1p2_reduced.pdf and
+	 * the official GPU firmware DT blob.
+	 *
+	 * Legend:
+	 * "NC" = not connected (no rail from the SoC)
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "ID_SDA",
+			  "ID_SCL",
+			  "SDA1",
+			  "SCL1",
+			  "GPIO_GCLK",
+			  "GPIO5",
+			  "GPIO6",
+			  "SPI_CE1_N",
+			  "SPI_CE0_N",
+			  "SPI_MISO",
+			  "SPI_MOSI",
+			  "SPI_SCLK",
+			  "GPIO12",
+			  "GPIO13",
+			  /* Serial port */
+			  "TXD0",
+			  "RXD0",
+			  "GPIO16",
+			  "GPIO17",
+			  "GPIO18",
+			  "GPIO19",
+			  "GPIO20",
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "GPIO26",
+			  "GPIO27",
+			  "SDA0",
+			  "SCL0",
+			  "", /* GPIO30 */
+			  "LAN_RUN",
+			  "CAM_GPIO1",
+			  "", /* GPIO33 */
+			  "", /* GPIO34 */
+			  "PWR_LOW_N",
+			  "", /* GPIO36 */
+			  "", /* GPIO37 */
+			  "USB_LIMIT",
+			  "", /* GPIO39 */
+			  "PWM0_OUT",
+			  "CAM_GPIO0",
+			  "SMPS_SCL",
+			  "SMPS_SDA",
+			  "ETHCLK",
+			  "PWM1_OUT",
+			  "HDMI_HPD_N",
+			  "STATUS_LED",
+			  /* Used by SD Card */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+
 	pinctrl-0 = <&gpioout &alt0 &i2s_alt0>;
 
 	/* I2S interface */
@@ -40,6 +107,12 @@
 	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
 };
 
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_gpio14>;

arch/arm/dts/bcm2836-rpi.dtsi

@@ -0,0 +1,6 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "bcm2835-rpi.dtsi"
+
+&vchiq {
+	compatible = "brcm,bcm2836-vchiq", "brcm,bcm2835-vchiq";
+};

arch/arm/dts/bcm2836.dtsi

@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0
 #include "bcm283x.dtsi"
 
 / {
@@ -8,28 +9,28 @@
 			 <0x40000000 0x40000000 0x00001000>;
 		dma-ranges = <0xc0000000 0x00000000 0x3f000000>;
 
-		local_intc: local_intc {
+		local_intc: local_intc@40000000 {
 			compatible = "brcm,bcm2836-l1-intc";
 			reg = <0x40000000 0x100>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 			interrupt-parent = <&local_intc>;
 		};
+	};
 
-		arm-pmu {
-			compatible = "arm,cortex-a7-pmu";
-			interrupt-parent = <&local_intc>;
-			interrupts = <9>;
-		};
+	arm-pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupt-parent = <&local_intc>;
+		interrupts = <9 IRQ_TYPE_LEVEL_HIGH>;
 	};
 
 	timer {
 		compatible = "arm,armv7-timer";
 		interrupt-parent = <&local_intc>;
-		interrupts = <0>, // PHYS_SECURE_PPI
-			     <1>, // PHYS_NONSECURE_PPI
-			     <3>, // VIRT_PPI
-			     <2>; // HYP_PPI
+		interrupts = <0 IRQ_TYPE_LEVEL_HIGH>, // PHYS_SECURE_PPI
+			     <1 IRQ_TYPE_LEVEL_HIGH>, // PHYS_NONSECURE_PPI
+			     <3 IRQ_TYPE_LEVEL_HIGH>, // VIRT_PPI
+			     <2 IRQ_TYPE_LEVEL_HIGH>; // HYP_PPI
 		always-on;
 	};
 
@@ -75,7 +76,7 @@
 	compatible = "brcm,bcm2836-armctrl-ic";
 	reg = <0x7e00b200 0x200>;
 	interrupt-parent = <&local_intc>;
-	interrupts = <8>;
+	interrupts = <8 IRQ_TYPE_LEVEL_HIGH>;
 };
 
 &cpu_thermal {

arch/arm/dts/bcm2837-rpi-3-a-plus.dts

@@ -0,0 +1,175 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2837.dtsi"
+#include "bcm2836-rpi.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
+
+/ {
+	compatible = "raspberrypi,3-model-a-plus", "brcm,bcm2837";
+	model = "Raspberry Pi 3 Model A+";
+
+	chosen {
+		/* 8250 auxiliary UART instead of pl011 */
+		stdout-path = "serial1:115200n8";
+	};
+
+	memory@0 {
+		reg = <0 0x20000000>;
+	};
+
+	leds {
+		act {
+			gpios = <&gpio 29 GPIO_ACTIVE_HIGH>;
+		};
+
+		pwr {
+			label = "PWR";
+			gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&firmware {
+	expgpio: gpio {
+		compatible = "raspberrypi,firmware-gpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "",
+				  "BT_WL_ON",
+				  "STATUS_LED_R",
+				  "",
+				  "",
+				  "CAM_GPIO0",
+				  "CAM_GPIO1",
+				  "";
+		status = "okay";
+	};
+};
+
+&gpio {
+	/*
+	 * This is mostly based on the official GPU firmware DT blob.
+	 *
+	 * Legend:
+	 * "NC" = not connected (no rail from the SoC)
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "ID_SDA",
+			  "ID_SCL",
+			  "SDA1",
+			  "SCL1",
+			  "GPIO_GCLK",
+			  "GPIO5",
+			  "GPIO6",
+			  "SPI_CE1_N",
+			  "SPI_CE0_N",
+			  "SPI_MISO",
+			  "SPI_MOSI",
+			  "SPI_SCLK",
+			  "GPIO12",
+			  "GPIO13",
+			  /* Serial port */
+			  "TXD1",
+			  "RXD1",
+			  "GPIO16",
+			  "GPIO17",
+			  "GPIO18",
+			  "GPIO19",
+			  "GPIO20",
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "GPIO26",
+			  "GPIO27",
+			  "HDMI_HPD_N",
+			  "STATUS_LED_G",
+			  /* Used by BT module */
+			  "CTS0",
+			  "RTS0",
+			  "TXD0",
+			  "RXD0",
+			  /* Used by Wifi */
+			  "SD1_CLK",
+			  "SD1_CMD",
+			  "SD1_DATA0",
+			  "SD1_DATA1",
+			  "SD1_DATA2",
+			  "SD1_DATA3",
+			  "PWM0_OUT",
+			  "PWM1_OUT",
+			  "", /* GPIO42 */
+			  "WIFI_CLK",
+			  "SDA0",
+			  "SCL0",
+			  "SMPS_SCL",
+			  "SMPS_SDA",
+			  /* Used by SD Card */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>;
+	status = "okay";
+};
+
+/*
+ * SDHCI is used to control the SDIO for wireless
+ *
+ * WL_REG_ON and BT_REG_ON of the CYW43455 Wifi/BT module are driven
+ * by a single GPIO. We can't give GPIO control to one of the drivers,
+ * otherwise the other part would get unexpectedly disturbed.
+ */
+&sdhci {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_gpio34>;
+	status = "okay";
+	bus-width = <4>;
+	non-removable;
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
+/* SDHOST is used to drive the SD card */
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	status = "okay";
+	bus-width = <4>;
+};
+
+/* uart0 communicates with the BT module */
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32 &gpclk2_gpio43>;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		max-speed = <2000000>;
+	};
+};
+
+/* uart1 is mapped to the pin header */
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_gpio14>;
+	status = "okay";
+};

arch/arm/dts/bcm2837-rpi-3-b-plus.dts

@@ -0,0 +1,178 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2837.dtsi"
+#include "bcm2836-rpi.dtsi"
+#include "bcm283x-rpi-lan7515.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
+
+/ {
+	compatible = "raspberrypi,3-model-b-plus", "brcm,bcm2837";
+	model = "Raspberry Pi 3 Model B+";
+
+	chosen {
+		/* 8250 auxiliary UART instead of pl011 */
+		stdout-path = "serial1:115200n8";
+	};
+
+	memory@0 {
+		reg = <0 0x40000000>;
+	};
+
+	leds {
+		act {
+			gpios = <&gpio 29 GPIO_ACTIVE_HIGH>;
+		};
+
+		pwr {
+			label = "PWR";
+			gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&firmware {
+	expgpio: gpio {
+		compatible = "raspberrypi,firmware-gpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "BT_ON",
+				  "WL_ON",
+				  "STATUS_LED_R",
+				  "LAN_RUN",
+				  "",
+				  "CAM_GPIO0",
+				  "CAM_GPIO1",
+				  "";
+		status = "okay";
+	};
+};
+
+&gpio {
+	/*
+	 * Taken from rpi_SCH_3bplus_1p0_reduced.pdf and
+	 * the official GPU firmware DT blob.
+	 *
+	 * Legend:
+	 * "NC" = not connected (no rail from the SoC)
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "ID_SDA",
+			  "ID_SCL",
+			  "SDA1",
+			  "SCL1",
+			  "GPIO_GCLK",
+			  "GPIO5",
+			  "GPIO6",
+			  "SPI_CE1_N",
+			  "SPI_CE0_N",
+			  "SPI_MISO",
+			  "SPI_MOSI",
+			  "SPI_SCLK",
+			  "GPIO12",
+			  "GPIO13",
+			  /* Serial port */
+			  "TXD1",
+			  "RXD1",
+			  "GPIO16",
+			  "GPIO17",
+			  "GPIO18",
+			  "GPIO19",
+			  "GPIO20",
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "GPIO26",
+			  "GPIO27",
+			  "HDMI_HPD_N",
+			  "STATUS_LED_G",
+			  /* Used by BT module */
+			  "CTS0",
+			  "RTS0",
+			  "TXD0",
+			  "RXD0",
+			  /* Used by Wifi */
+			  "SD1_CLK",
+			  "SD1_CMD",
+			  "SD1_DATA0",
+			  "SD1_DATA1",
+			  "SD1_DATA2",
+			  "SD1_DATA3",
+			  "PWM0_OUT",
+			  "PWM1_OUT",
+			  "ETHCLK",
+			  "WIFI_CLK",
+			  "SDA0",
+			  "SCL0",
+			  "SMPS_SCL",
+			  "SMPS_SDA",
+			  /* Used by SD Card */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>;
+	status = "okay";
+};
+
+/* SDHCI is used to control the SDIO for wireless */
+&sdhci {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_gpio34>;
+	status = "okay";
+	bus-width = <4>;
+	non-removable;
+	mmc-pwrseq = <&wifi_pwrseq>;
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
+/* SDHOST is used to drive the SD card */
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	status = "okay";
+	bus-width = <4>;
+};
+
+/* uart0 communicates with the BT module */
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32 &gpclk2_gpio43>;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		max-speed = <2000000>;
+		shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+/* uart1 is mapped to the pin header */
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_gpio14>;
+	status = "okay";
+};

arch/arm/dts/bcm2837-rpi-3-b.dts

@@ -1,6 +1,7 @@
+// SPDX-License-Identifier: GPL-2.0
 /dts-v1/;
 #include "bcm2837.dtsi"
-#include "bcm2835-rpi.dtsi"
+#include "bcm2836-rpi.dtsi"
 #include "bcm283x-rpi-smsc9514.dtsi"
 #include "bcm283x-rpi-usb-host.dtsi"
 
@@ -8,15 +9,122 @@
 	compatible = "raspberrypi,3-model-b", "brcm,bcm2837";
 	model = "Raspberry Pi 3 Model B";
 
-	memory {
+	chosen {
+		/* 8250 auxiliary UART instead of pl011 */
+		stdout-path = "serial1:115200n8";
+	};
+
+	memory@0 {
 		reg = <0 0x40000000>;
 	};
 
 	leds {
 		act {
-			gpios = <&gpio 47 0>;
+			gpios = <&expgpio 2 GPIO_ACTIVE_HIGH>;
 		};
 	};
+
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&firmware {
+	expgpio: gpio {
+		compatible = "raspberrypi,firmware-gpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "BT_ON",
+				  "WL_ON",
+				  "STATUS_LED",
+				  "LAN_RUN",
+				  "HDMI_HPD_N",
+				  "CAM_GPIO0",
+				  "CAM_GPIO1",
+				  "PWR_LOW_N";
+		status = "okay";
+	};
+};
+
+&gpio {
+	/*
+	 * Taken from rpi_SCH_3b_1p2_reduced.pdf and
+	 * the official GPU firmware DT blob.
+	 *
+	 * Legend:
+	 * "NC" = not connected (no rail from the SoC)
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "ID_SDA",
+			  "ID_SCL",
+			  "SDA1",
+			  "SCL1",
+			  "GPIO_GCLK",
+			  "GPIO5",
+			  "GPIO6",
+			  "SPI_CE1_N",
+			  "SPI_CE0_N",
+			  "SPI_MISO",
+			  "SPI_MOSI",
+			  "SPI_SCLK",
+			  "GPIO12",
+			  "GPIO13",
+			  /* Serial port */
+			  "TXD1",
+			  "RXD1",
+			  "GPIO16",
+			  "GPIO17",
+			  "GPIO18",
+			  "GPIO19",
+			  "GPIO20",
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "GPIO26",
+			  "GPIO27",
+			  "", /* GPIO 28 */
+			  "LAN_RUN_BOOT",
+			  /* Used by BT module */
+			  "CTS0",
+			  "RTS0",
+			  "TXD0",
+			  "RXD0",
+			  /* Used by Wifi */
+			  "SD1_CLK",
+			  "SD1_CMD",
+			  "SD1_DATA0",
+			  "SD1_DATA1",
+			  "SD1_DATA2",
+			  "SD1_DATA3",
+			  "PWM0_OUT",
+			  "PWM1_OUT",
+			  "ETHCLK",
+			  "WIFI_CLK",
+			  "SDA0",
+			  "SCL0",
+			  "SMPS_SCL",
+			  "SMPS_SDA",
+			  /* Used by SD Card */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>;
+	status = "okay";
+};
+
+&hdmi {
+	hpd-gpios = <&expgpio 4 GPIO_ACTIVE_LOW>;
 };
 
 /* uart0 communicates with the BT module */
@@ -24,6 +132,12 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_gpio32 &gpclk2_gpio43>;
 	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		max-speed = <2000000>;
+		shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>;
+	};
 };
 
 /* uart1 is mapped to the pin header */
@@ -35,11 +149,19 @@
 
 /* SDHCI is used to control the SDIO for wireless */
 &sdhci {
+	#address-cells = <1>;
+	#size-cells = <0>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&emmc_gpio34>;
 	status = "okay";
 	bus-width = <4>;
 	non-removable;
+	mmc-pwrseq = <&wifi_pwrseq>;
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
 };
 
 /* SDHOST is used to drive the SD card */

arch/arm/dts/bcm2837-rpi-cm3-io3.dts

@@ -0,0 +1,87 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2837-rpi-cm3.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
+
+/ {
+	compatible = "raspberrypi,3-compute-module", "brcm,bcm2837";
+	model = "Raspberry Pi Compute Module 3 IO board V3.0";
+};
+
+&gpio {
+	/*
+	 * This is based on the official GPU firmware DT blob.
+	 *
+	 * Legend:
+	 * "NC" = not connected (no rail from the SoC)
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "GPIO0",
+			  "GPIO1",
+			  "GPIO2",
+			  "GPIO3",
+			  "GPIO4",
+			  "GPIO5",
+			  "GPIO6",
+			  "GPIO7",
+			  "GPIO8",
+			  "GPIO9",
+			  "GPIO10",
+			  "GPIO11",
+			  "GPIO12",
+			  "GPIO13",
+			  "GPIO14",
+			  "GPIO15",
+			  "GPIO16",
+			  "GPIO17",
+			  "GPIO18",
+			  "GPIO19",
+			  "GPIO20",
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "GPIO26",
+			  "GPIO27",
+			  "GPIO28",
+			  "GPIO29",
+			  "GPIO30",
+			  "GPIO31",
+			  "GPIO32",
+			  "GPIO33",
+			  "GPIO34",
+			  "GPIO35",
+			  "GPIO36",
+			  "GPIO37",
+			  "GPIO38",
+			  "GPIO39",
+			  "GPIO40",
+			  "GPIO41",
+			  "GPIO42",
+			  "GPIO43",
+			  "GPIO44",
+			  "GPIO45",
+			  "GPIO46",
+			  "GPIO47",
+			  /* Used by eMMC */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+
+	pinctrl-0 = <&gpioout &alt0>;
+};
+
+&hdmi {
+	hpd-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_gpio14>;
+	status = "okay";
+};

arch/arm/dts/bcm2837-rpi-cm3.dtsi

@@ -0,0 +1,52 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2837.dtsi"
+#include "bcm2836-rpi.dtsi"
+
+/ {
+	memory@0 {
+		reg = <0 0x40000000>;
+	};
+
+	reg_3v3: fixed-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_1v8: fixed-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
+};
+
+&firmware {
+	expgpio: gpio {
+		compatible = "raspberrypi,firmware-gpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "HDMI_HPD_N",
+				  "EMMC_EN_N",
+				  "NC",
+				  "NC",
+				  "NC",
+				  "NC",
+				  "NC",
+				  "NC";
+		status = "okay";
+	};
+};
+
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	vmmc-supply = <&reg_3v3>;
+	vqmmc-supply = <&reg_1v8>;
+	status = "okay";
+};

arch/arm/dts/bcm2837.dtsi

@@ -8,22 +8,28 @@
 			 <0x40000000 0x40000000 0x00001000>;
 		dma-ranges = <0xc0000000 0x00000000 0x3f000000>;
 
-		local_intc: local_intc {
+		local_intc: local_intc@40000000 {
 			compatible = "brcm,bcm2836-l1-intc";
 			reg = <0x40000000 0x100>;
 			interrupt-controller;
-			#interrupt-cells = <1>;
+			#interrupt-cells = <2>;
 			interrupt-parent = <&local_intc>;
 		};
 	};
 
+	arm-pmu {
+		compatible = "arm,cortex-a53-pmu";
+		interrupt-parent = <&local_intc>;
+		interrupts = <9 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
 	timer {
 		compatible = "arm,armv7-timer";
 		interrupt-parent = <&local_intc>;
-		interrupts = <0>, // PHYS_SECURE_PPI
-			     <1>, // PHYS_NONSECURE_PPI
-			     <3>, // VIRT_PPI
-			     <2>; // HYP_PPI
+		interrupts = <0 IRQ_TYPE_LEVEL_HIGH>, // PHYS_SECURE_PPI
+			     <1 IRQ_TYPE_LEVEL_HIGH>, // PHYS_NONSECURE_PPI
+			     <3 IRQ_TYPE_LEVEL_HIGH>, // VIRT_PPI
+			     <2 IRQ_TYPE_LEVEL_HIGH>; // HYP_PPI
 		always-on;
 	};
 
@@ -73,7 +79,7 @@
 	compatible = "brcm,bcm2836-armctrl-ic";
 	reg = <0x7e00b200 0x200>;
 	interrupt-parent = <&local_intc>;
-	interrupts = <8>;
+	interrupts = <8 IRQ_TYPE_LEVEL_HIGH>;
 };
 
 &cpu_thermal {

arch/arm/dts/bcm283x-rpi-lan7515.dtsi

@@ -0,0 +1,41 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/net/microchip-lan78xx.h>
+
+/ {
+	aliases {
+		ethernet0 = &ethernet;
+	};
+};
+
+&usb {
+	usb-port@1 {
+		compatible = "usb424,2514";
+		reg = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		usb-port@1 {
+			compatible = "usb424,2514";
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			ethernet: ethernet@1 {
+				compatible = "usb424,7800";
+				reg = <1>;
+
+				mdio {
+					#address-cells = <0x1>;
+					#size-cells = <0x0>;
+					eth_phy: ethernet-phy@1 {
+						reg = <1>;
+						microchip,led-modes = <
+							LAN78XX_LINK_1000_ACTIVITY
+							LAN78XX_LINK_10_100_ACTIVITY
+						>;
+					};
+				};
+			};
+		};
+	};
+};

arch/arm/dts/bcm283x-rpi-smsc9512.dtsi

@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0
 / {
 	aliases {
 		ethernet0 = &ethernet;

arch/arm/dts/bcm283x-rpi-usb-otg.dtsi

@@ -0,0 +1,11 @@
+// SPDX-License-Identifier: GPL-2.0
+&usb {
+	dr_mode = "otg";
+	g-rx-fifo-size = <256>;
+	g-np-tx-fifo-size = <32>;
+	/*
+	 * According to dwc2 the sum of all device EP
+	 * fifo sizes shouldn't exceed 3776 bytes.
+	 */
+	g-tx-fifo-size = <256 256 512 512 512 768 768>;
+};

arch/arm/dts/bcm283x.dtsi

@@ -2,6 +2,8 @@
 #include <dt-bindings/clock/bcm2835.h>
 #include <dt-bindings/clock/bcm2835-aux.h>
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/soc/bcm2835-pm.h>
 
 /* firmware-provided startup stubs live here, where the secondary CPUs are
  * spinning.
@@ -20,8 +22,13 @@
 	#address-cells = <1>;
 	#size-cells = <1>;
 
+	aliases {
+		serial0 = &uart0;
+		serial1 = &uart1;
+	};
+
 	chosen {
-		bootargs = "earlyprintk console=ttyAMA0";
+		stdout-path = "serial0:115200n8";
 	};
 
 	thermal-zones {
@@ -44,7 +51,7 @@
 		};
 	};
 
-	soc: soc {
+	soc {
 		compatible = "simple-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -60,6 +67,12 @@
 			clock-frequency = <1000000>;
 		};
 
+		txp@7e004000 {
+			compatible = "brcm,bcm2835-txp";
+			reg = <0x7e004000 0x20>;
+			interrupts = <1 11>;
+		};
+
 		dma: dma@7e007000 {
 			compatible = "brcm,bcm2835-dma";
 			reg = <0x7e007000 0xf00>;
@@ -108,9 +121,18 @@
 			#interrupt-cells = <2>;
 		};
 
-		watchdog@7e100000 {
-			compatible = "brcm,bcm2835-pm-wdt";
-			reg = <0x7e100000 0x28>;
+		pm: watchdog@7e100000 {
+			compatible = "brcm,bcm2835-pm", "brcm,bcm2835-pm-wdt";
+			#power-domain-cells = <1>;
+			#reset-cells = <1>;
+			reg = <0x7e100000 0x114>,
+			      <0x7e00a000 0x24>;
+			clocks = <&clocks BCM2835_CLOCK_V3D>,
+				 <&clocks BCM2835_CLOCK_PERI_IMAGE>,
+				 <&clocks BCM2835_CLOCK_H264>,
+				 <&clocks BCM2835_CLOCK_ISP>;
+			clock-names = "v3d", "peri_image", "h264", "isp";
+			system-power-controller;
 		};
 
 		clocks: cprman@7e101000 {
@@ -130,6 +152,7 @@
 		rng@7e104000 {
 			compatible = "brcm,bcm2835-rng";
 			reg = <0x7e104000 0x10>;
+			interrupts = <2 29>;
 		};
 
 		mailbox: mailbox@7e00b880 {
@@ -217,6 +240,7 @@
 			gpclk2_gpio43: gpclk2_gpio43 {
 				brcm,pins = <43>;
 				brcm,function = <BCM2835_FSEL_ALT0>;
+				brcm,pull = <BCM2835_PUD_OFF>;
 			};
 
 			i2c0_gpio0: i2c0_gpio0 {
@@ -329,10 +353,12 @@
 			uart0_ctsrts_gpio30: uart0_ctsrts_gpio30 {
 				brcm,pins = <30 31>;
 				brcm,function = <BCM2835_FSEL_ALT3>;
+				brcm,pull = <BCM2835_PUD_UP BCM2835_PUD_OFF>;
 			};
 			uart0_gpio32: uart0_gpio32 {
 				brcm,pins = <32 33>;
 				brcm,function = <BCM2835_FSEL_ALT3>;
+				brcm,pull = <BCM2835_PUD_OFF BCM2835_PUD_UP>;
 			};
 			uart0_gpio36: uart0_gpio36 {
 				brcm,pins = <36 37>;
@@ -391,8 +417,8 @@
 
 		i2s: i2s@7e203000 {
 			compatible = "brcm,bcm2835-i2s";
-			reg = <0x7e203000 0x20>,
-			      <0x7e101098 0x02>;
+			reg = <0x7e203000 0x24>;
+			clocks = <&clocks BCM2835_CLOCK_PCM>;
 
 			dmas = <&dma 2>,
 			       <&dma 3>;
@@ -432,6 +458,17 @@
 			interrupts = <2 14>; /* pwa1 */
 		};
 
+		dpi: dpi@7e208000 {
+			compatible = "brcm,bcm2835-dpi";
+			reg = <0x7e208000 0x8c>;
+			clocks = <&clocks BCM2835_CLOCK_VPU>,
+				 <&clocks BCM2835_CLOCK_DPI>;
+			clock-names = "core", "pixel";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
 		dsi0: dsi@7e209000 {
 			compatible = "brcm,bcm2835-dsi0";
 			reg = <0x7e209000 0x78>;
@@ -459,7 +496,7 @@
 			status = "disabled";
 		};
 
-		aux: aux@0x7e215000 {
+		aux: aux@7e215000 {
 			compatible = "brcm,bcm2835-aux";
 			#clock-cells = <1>;
 			reg = <0x7e215000 0x8>;
@@ -602,6 +639,7 @@
 			compatible = "brcm,bcm2835-v3d";
 			reg = <0x7ec00000 0x1000>;
 			interrupts = <1 10>;
+			power-domains = <&pm BCM2835_POWER_DOMAIN_GRAFX_V3D>;
 		};
 
 		vc4: gpu {
@@ -634,7 +672,6 @@
 
 	usbphy: phy {
 		compatible = "usb-nop-xceiv";
+		#phy-cells = <0>;
 	};
 };
-
-#include "bcm283x-uboot.dtsi"

arch/arm/dts/fsl-imx8qm-apalis-u-boot.dtsi

@@ -0,0 +1,128 @@
+// SPDX-License-Identifier: GPL-2.0+ OR X11
+/*
+ * Copyright 2019 Toradex AG
+ */
+
+&mu {
+	u-boot,dm-spl;
+};
+
+&clk {
+	u-boot,dm-spl;
+};
+
+&iomuxc {
+	u-boot,dm-spl;
+};
+
+&pd_lsio {
+	u-boot,dm-spl;
+};
+
+&pd_lsio_gpio0 {
+	u-boot,dm-spl;
+};
+
+&pd_lsio_gpio1 {
+	u-boot,dm-spl;
+};
+
+&pd_lsio_gpio2 {
+	u-boot,dm-spl;
+};
+
+&pd_lsio_gpio3 {
+	u-boot,dm-spl;
+};
+
+&pd_lsio_gpio4 {
+	u-boot,dm-spl;
+};
+
+&pd_lsio_gpio5 {
+	u-boot,dm-spl;
+};
+
+&pd_lsio_gpio6 {
+	u-boot,dm-spl;
+};
+
+&pd_lsio_gpio7 {
+	u-boot,dm-spl;
+};
+
+&pd_conn {
+	u-boot,dm-spl;
+};
+
+&pd_conn_sdch0 {
+	u-boot,dm-spl;
+};
+
+&pd_conn_sdch1 {
+	u-boot,dm-spl;
+};
+
+&pd_conn_sdch2 {
+	u-boot,dm-spl;
+};
+
+&gpio0 {
+	u-boot,dm-spl;
+};
+
+&gpio1 {
+	u-boot,dm-spl;
+};
+
+&gpio2 {
+	u-boot,dm-spl;
+};
+
+&gpio3 {
+	u-boot,dm-spl;
+};
+
+&gpio4 {
+	u-boot,dm-spl;
+};
+
+&gpio5 {
+	u-boot,dm-spl;
+};
+
+&gpio6 {
+	u-boot,dm-spl;
+};
+
+&gpio7 {
+	u-boot,dm-spl;
+};
+
+&lpuart0 {
+	u-boot,dm-spl;
+};
+
+&lpuart1 {
+	u-boot,dm-spl;
+};
+
+&lpuart2 {
+	u-boot,dm-spl;
+};
+
+&lpuart3 {
+	u-boot,dm-spl;
+};
+
+&usdhc1 {
+	u-boot,dm-spl;
+};
+
+&usdhc2 {
+	u-boot,dm-spl;
+};
+
+&usdhc3 {
+	u-boot,dm-spl;
+};

arch/arm/dts/fsl-imx8qm-apalis.dts

@@ -0,0 +1,615 @@
+// SPDX-License-Identifier: GPL-2.0+ OR X11
+/*
+ * Copyright 2017-2019 Toradex
+ */
+
+/dts-v1/;
+
+/* First 128KB is for PSCI ATF. */
+/memreserve/ 0x80000000 0x00020000;
+
+#include "fsl-imx8qm.dtsi"
+#include "fsl-imx8qm-apalis-u-boot.dtsi"
+
+/ {
+	model = "Toradex Apalis iMX8QM";
+	compatible = "toradex,apalis-imx8qm", "fsl,imx8qm";
+
+	chosen {
+		bootargs = "console=ttyLP1,115200 earlycon=lpuart32,0x5a070000,115200";
+		stdout-path = &lpuart1;
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_cam1_gpios>, <&pinctrl_dap1_gpios>,
+		    <&pinctrl_esai0_gpios>, <&pinctrl_fec2_gpios>,
+		    <&pinctrl_gpio12>, <&pinctrl_gpio34>, <&pinctrl_gpio56>,
+		    <&pinctrl_gpio7>, <&pinctrl_gpio8>, <&pinctrl_gpio_bkl_on>,
+		    <&pinctrl_gpio_keys>, <&pinctrl_gpio_pwm0>,
+		    <&pinctrl_gpio_pwm1>, <&pinctrl_gpio_pwm2>,
+		    <&pinctrl_gpio_pwm3>, <&pinctrl_gpio_pwm_bkl>,
+		    <&pinctrl_gpio_usbh_en>, <&pinctrl_gpio_usbh_oc_n>,
+		    <&pinctrl_gpio_usbo1_en>, <&pinctrl_gpio_usbo1_oc_n>,
+		    <&pinctrl_lpuart1ctrl>, <&pinctrl_lvds0_i2c0_gpio>,
+		    <&pinctrl_lvds1_i2c0_gpios>, <&pinctrl_mipi_dsi_0_1_en>,
+		    <&pinctrl_mipi_dsi1_gpios>, <&pinctrl_mlb_gpios>,
+		    <&pinctrl_qspi1a_gpios>, <&pinctrl_sata1_act>,
+		    <&pinctrl_sim0_gpios>, <&pinctrl_usdhc1_gpios>;
+
+	apalis-imx8qm {
+		pinctrl_gpio12: gpio12grp {
+			fsl,pins = <
+				/* Apalis GPIO1 */
+				SC_P_M40_GPIO0_00_LSIO_GPIO0_IO08		0x06000021
+				/* Apalis GPIO2 */
+				SC_P_M40_GPIO0_01_LSIO_GPIO0_IO09		0x06000021
+			>;
+		};
+
+		pinctrl_gpio34: gpio34grp {
+			fsl,pins = <
+				/* Apalis GPIO3 */
+				SC_P_M41_GPIO0_00_LSIO_GPIO0_IO12		0x06000021
+				/* Apalis GPIO4 */
+				SC_P_M41_GPIO0_01_LSIO_GPIO0_IO13		0x06000021
+			>;
+		};
+
+		pinctrl_gpio56: gpio56grp {
+			fsl,pins = <
+				/* Apalis GPIO5 */
+				SC_P_FLEXCAN2_RX_LSIO_GPIO4_IO01		0x06000021
+				/* Apalis GPIO6 */
+				SC_P_FLEXCAN2_TX_LSIO_GPIO4_IO02		0x06000021
+			>;
+		};
+
+		pinctrl_gpio7: gpio7 {
+			fsl,pins = <
+				/* Apalis GPIO7 */
+				SC_P_MLB_SIG_LSIO_GPIO3_IO26			0x00000021
+			>;
+		};
+
+		pinctrl_gpio8: gpio8 {
+			fsl,pins = <
+				/* Apalis GPIO8 */
+				SC_P_MLB_DATA_LSIO_GPIO3_IO28			0x00000021
+			>;
+		};
+
+		pinctrl_gpio_keys: gpio-keys {
+			fsl,pins = <
+				/* Apalis WAKE1_MICO */
+				SC_P_SPI3_CS0_LSIO_GPIO2_IO20		0x06000021
+			>;
+		};
+
+		pinctrl_fec1: fec1grp {
+			fsl,pins = <
+				SC_P_COMP_CTL_GPIO_1V8_3V3_ENET_ENETB_PAD	0x000014a0 /* Use pads in 3.3V mode */
+				SC_P_ENET0_MDC_CONN_ENET0_MDC			0x06000020
+				SC_P_ENET0_MDIO_CONN_ENET0_MDIO			0x06000020
+				SC_P_ENET0_RGMII_TX_CTL_CONN_ENET0_RGMII_TX_CTL	0x06000020
+				SC_P_ENET0_RGMII_TXC_CONN_ENET0_RGMII_TXC	0x06000020
+				SC_P_ENET0_RGMII_TXD0_CONN_ENET0_RGMII_TXD0	0x06000020
+				SC_P_ENET0_RGMII_TXD1_CONN_ENET0_RGMII_TXD1	0x06000020
+				SC_P_ENET0_RGMII_TXD2_CONN_ENET0_RGMII_TXD2	0x06000020
+				SC_P_ENET0_RGMII_TXD3_CONN_ENET0_RGMII_TXD3	0x06000020
+				SC_P_ENET0_RGMII_RXC_CONN_ENET0_RGMII_RXC	0x06000020
+				SC_P_ENET0_RGMII_RX_CTL_CONN_ENET0_RGMII_RX_CTL	0x06000020
+				SC_P_ENET0_RGMII_RXD0_CONN_ENET0_RGMII_RXD0	0x06000020
+				SC_P_ENET0_RGMII_RXD1_CONN_ENET0_RGMII_RXD1	0x06000020
+				SC_P_ENET0_RGMII_RXD2_CONN_ENET0_RGMII_RXD2	0x06000020
+				SC_P_ENET0_RGMII_RXD3_CONN_ENET0_RGMII_RXD3	0x06000020
+				SC_P_ENET0_REFCLK_125M_25M_CONN_ENET0_REFCLK_125M_25M	0x06000020
+				/* ETH_RESET# */
+				SC_P_LVDS1_GPIO01_LSIO_GPIO1_IO11		0x06000020
+			>;
+		};
+
+		pinctrl_gpio_bkl_on: gpio-bkl-on {
+			fsl,pins = <
+				/* Apalis BKL_ON */
+				SC_P_LVDS0_GPIO00_LSIO_GPIO1_IO04	0x00000021
+			>;
+		};
+
+		/* Apalis I2C2 (DDC) */
+		pinctrl_lpi2c0: lpi2c0grp {
+			fsl,pins = <
+				SC_P_HDMI_TX0_TS_SCL_DMA_I2C0_SCL	0x04000022
+				SC_P_HDMI_TX0_TS_SDA_DMA_I2C0_SDA	0x04000022
+			>;
+		};
+
+		pinctrl_cam1_gpios: cam1gpiosgrp {
+			fsl,pins = <
+				/* Apalis CAM1_D7 */
+				SC_P_MIPI_DSI1_I2C0_SCL_LSIO_GPIO1_IO20	0x00000021
+				/* Apalis CAM1_D6 */
+				SC_P_MIPI_DSI1_I2C0_SDA_LSIO_GPIO1_IO21	0x00000021
+				/* Apalis CAM1_D5 */
+				SC_P_ESAI0_TX0_LSIO_GPIO2_IO26		0x00000021
+				/* Apalis CAM1_D4 */
+				SC_P_ESAI0_TX1_LSIO_GPIO2_IO27		0x00000021
+				/* Apalis CAM1_D3 */
+				SC_P_ESAI0_TX2_RX3_LSIO_GPIO2_IO28	0x00000021
+				/* Apalis CAM1_D2 */
+				SC_P_ESAI0_TX3_RX2_LSIO_GPIO2_IO29	0x00000021
+				/* Apalis CAM1_D1 */
+				SC_P_ESAI0_TX4_RX1_LSIO_GPIO2_IO30	0x00000021
+				/* Apalis CAM1_D0 */
+				SC_P_ESAI0_TX5_RX0_LSIO_GPIO2_IO31	0x00000021
+				/* Apalis CAM1_PCLK */
+				SC_P_MCLK_IN0_LSIO_GPIO3_IO00		0x00000021
+				/* Apalis CAM1_MCLK */
+				SC_P_SPI3_SDO_LSIO_GPIO2_IO18		0x00000021
+				/* Apalis CAM1_VSYNC */
+				SC_P_ESAI0_SCKR_LSIO_GPIO2_IO24		0x00000021
+				/* Apalis CAM1_HSYNC */
+				SC_P_ESAI0_SCKT_LSIO_GPIO2_IO25		0x00000021
+			>;
+		};
+
+		pinctrl_dap1_gpios: dap1gpiosgrp {
+			fsl,pins = <
+				/* Apalis DAP1_MCLK */
+				SC_P_SPI3_SDI_LSIO_GPIO2_IO19			0x00000021
+				/* Apalis DAP1_D_OUT */
+				SC_P_SAI1_RXC_LSIO_GPIO3_IO12			0x00000021
+				/* Apalis DAP1_RESET */
+				SC_P_ESAI1_SCKT_LSIO_GPIO2_IO07			0x00000021
+				/* Apalis DAP1_BIT_CLK */
+				SC_P_SPI0_CS1_LSIO_GPIO3_IO06			0x00000021
+				/* Apalis DAP1_D_IN */
+				SC_P_SAI1_RXFS_LSIO_GPIO3_IO14			0x00000021
+				/* Apalis DAP1_SYNC */
+				SC_P_SPI2_CS1_LSIO_GPIO3_IO11			0x00000021
+				/* Wi-Fi_I2S_EN# */
+				SC_P_ESAI1_TX5_RX0_LSIO_GPIO2_IO13		0x00000021
+			>;
+		};
+
+		pinctrl_esai0_gpios: esai0gpiosgrp {
+			fsl,pins = <
+				/* Apalis LCD1_G1 */
+				SC_P_ESAI0_FSR_LSIO_GPIO2_IO22			0x00000021
+				/* Apalis LCD1_G2 */
+				SC_P_ESAI0_FST_LSIO_GPIO2_IO23			0x00000021
+			>;
+		};
+
+		pinctrl_fec2_gpios: fec2gpiosgrp {
+			fsl,pins = <
+				SC_P_COMP_CTL_GPIO_1V8_3V3_ENET_ENETA_PAD	0x000014a0
+				/* Apalis LCD1_R1 */
+				SC_P_ENET1_MDC_LSIO_GPIO4_IO18			0x00000021
+				/* Apalis LCD1_R0 */
+				SC_P_ENET1_MDIO_LSIO_GPIO4_IO17			0x00000021
+				/* Apalis LCD1_G0 */
+				SC_P_ENET1_REFCLK_125M_25M_LSIO_GPIO4_IO16	0x00000021
+				/* Apalis LCD1_R7 */
+				SC_P_ENET1_RGMII_RX_CTL_LSIO_GPIO6_IO17		0x00000021
+				/* Apalis LCD1_DE */
+				SC_P_ENET1_RGMII_RXD0_LSIO_GPIO6_IO18		0x00000021
+				/* Apalis LCD1_HSYNC */
+				SC_P_ENET1_RGMII_RXD1_LSIO_GPIO6_IO19		0x00000021
+				/* Apalis LCD1_VSYNC */
+				SC_P_ENET1_RGMII_RXD2_LSIO_GPIO6_IO20		0x00000021
+				/* Apalis LCD1_PCLK */
+				SC_P_ENET1_RGMII_RXD3_LSIO_GPIO6_IO21		0x00000021
+				/* Apalis LCD1_R6 */
+				SC_P_ENET1_RGMII_TX_CTL_LSIO_GPIO6_IO11		0x00000021
+				/* Apalis LCD1_R5 */
+				SC_P_ENET1_RGMII_TXC_LSIO_GPIO6_IO10		0x00000021
+				/* Apalis LCD1_R4 */
+				SC_P_ENET1_RGMII_TXD0_LSIO_GPIO6_IO12		0x00000021
+				/* Apalis LCD1_R3 */
+				SC_P_ENET1_RGMII_TXD1_LSIO_GPIO6_IO13		0x00000021
+				/* Apalis LCD1_R2 */
+				SC_P_ENET1_RGMII_TXD2_LSIO_GPIO6_IO14		0x00000021
+			>;
+		};
+
+		pinctrl_lvds0_i2c0_gpio: lvds0i2c0gpio {
+			fsl,pins = <
+				/* Apalis TS_2 */
+				SC_P_LVDS0_I2C0_SCL_LSIO_GPIO1_IO06		0x00000021
+			>;
+		};
+
+		pinctrl_lvds1_i2c0_gpios: lvds1i2c0gpiosgrp {
+			fsl,pins = <
+				/* Apalis LCD1_G6 */
+				SC_P_LVDS1_I2C0_SCL_LSIO_GPIO1_IO12		0x00000021
+				/* Apalis LCD1_G7 */
+				SC_P_LVDS1_I2C0_SDA_LSIO_GPIO1_IO13		0x00000021
+			>;
+		};
+
+		pinctrl_mipi_dsi1_gpios: mipidsi1gpiosgrp {
+			fsl,pins = <
+				/* Apalis TS_4 */
+				SC_P_MIPI_DSI1_GPIO0_00_LSIO_GPIO1_IO22		0x00000021
+			>;
+		};
+
+		pinctrl_mlb_gpios: mlbgpiosgrp {
+			fsl,pins = <
+				/* Apalis TS_1 */
+				SC_P_MLB_CLK_LSIO_GPIO3_IO27			0x00000021
+			>;
+		};
+
+		pinctrl_qspi1a_gpios: qspi1agpiosgrp {
+			fsl,pins = <
+				/* Apalis LCD1_B0 */
+				SC_P_QSPI1A_DATA0_LSIO_GPIO4_IO26		0x00000021
+				/* Apalis LCD1_B1 */
+				SC_P_QSPI1A_DATA1_LSIO_GPIO4_IO25		0x00000021
+				/* Apalis LCD1_B2 */
+				SC_P_QSPI1A_DATA2_LSIO_GPIO4_IO24		0x00000021
+				/* Apalis LCD1_B3 */
+				SC_P_QSPI1A_DATA3_LSIO_GPIO4_IO23		0x00000021
+				/* Apalis LCD1_B5 */
+				SC_P_QSPI1A_DQS_LSIO_GPIO4_IO22			0x00000021
+				/* Apalis LCD1_B7 */
+				SC_P_QSPI1A_SCLK_LSIO_GPIO4_IO21		0x00000021
+				/* Apalis LCD1_B4 */
+				SC_P_QSPI1A_SS0_B_LSIO_GPIO4_IO19		0x00000021
+				/* Apalis LCD1_B6 */
+				SC_P_QSPI1A_SS1_B_LSIO_GPIO4_IO20		0x00000021
+			>;
+		};
+
+		pinctrl_sim0_gpios: sim0gpiosgrp {
+			fsl,pins = <
+				/* Apalis LCD1_G5 */
+				SC_P_SIM0_CLK_LSIO_GPIO0_IO00			0x00000021
+				/* Apalis LCD1_G3 */
+				SC_P_SIM0_GPIO0_00_LSIO_GPIO0_IO05		0x00000021
+				/* Apalis TS_5 */
+				SC_P_SIM0_IO_LSIO_GPIO0_IO02			0x00000021
+				/* Apalis LCD1_G4 */
+				SC_P_SIM0_RST_LSIO_GPIO0_IO01			0x00000021
+			>;
+		};
+
+		pinctrl_usdhc1_gpios: usdhc1gpiosgrp {
+			fsl,pins = <
+				/* Apalis TS_6 */
+				SC_P_USDHC1_STROBE_LSIO_GPIO5_IO23		0x00000021
+			>;
+		};
+
+		pinctrl_mipi_dsi_0_1_en: mipi_dsi_0_1_en {
+			fsl,pins = <
+				/* Apalis TS_3 */
+				SC_P_LVDS0_I2C0_SDA_LSIO_GPIO1_IO07		0x00000021
+			>;
+		};
+
+		/* On-module I2C */
+		pinctrl_lpi2c1: lpi2c1grp {
+			fsl,pins = <
+				SC_P_GPT0_CLK_DMA_I2C1_SCL		0x04000020
+				SC_P_GPT0_CAPTURE_DMA_I2C1_SDA		0x04000020
+			>;
+		};
+
+		/* Apalis I2C1 */
+		pinctrl_lpi2c2: lpi2c2grp {
+			fsl,pins = <
+				SC_P_GPT1_CLK_DMA_I2C2_SCL		0x04000020
+				SC_P_GPT1_CAPTURE_DMA_I2C2_SDA		0x04000020
+			>;
+		};
+
+		/* Apalis I2C3 (CAM) */
+		pinctrl_lpi2c3: lpi2c3grp {
+			fsl,pins = <
+				SC_P_SIM0_PD_DMA_I2C3_SCL		0x04000020
+				SC_P_SIM0_POWER_EN_DMA_I2C3_SDA		0x04000020
+			>;
+		};
+
+		/* Apalis UART3 */
+		pinctrl_lpuart0: lpuart0grp {
+			fsl,pins = <
+				SC_P_UART0_RX_DMA_UART0_RX		0x06000020
+				SC_P_UART0_TX_DMA_UART0_TX		0x06000020
+			>;
+		};
+
+		/* Apalis UART1 */
+		pinctrl_lpuart1: lpuart1grp {
+			fsl,pins = <
+				SC_P_UART1_RX_DMA_UART1_RX		0x06000020
+				SC_P_UART1_TX_DMA_UART1_TX		0x06000020
+				SC_P_UART1_CTS_B_DMA_UART1_CTS_B	0x06000020
+				SC_P_UART1_RTS_B_DMA_UART1_RTS_B	0x06000020
+			>;
+		};
+
+		pinctrl_lpuart1ctrl: lpuart1ctrlgrp {
+			fsl,pins = <
+				/* Apalis UART1_DTR */
+				SC_P_M40_I2C0_SCL_LSIO_GPIO0_IO06	0x00000021
+				/* Apalis UART1_DSR */
+				SC_P_M40_I2C0_SDA_LSIO_GPIO0_IO07	0x00000021
+				/* Apalis UART1_DCD */
+				SC_P_M41_I2C0_SCL_LSIO_GPIO0_IO10	0x00000021
+				/* Apalis UART1_RI */
+				SC_P_M41_I2C0_SDA_LSIO_GPIO0_IO11	0x00000021
+			>;
+		};
+
+		/* Apalis UART4 */
+		pinctrl_lpuart2: lpuart2grp {
+			fsl,pins = <
+				SC_P_LVDS0_I2C1_SCL_DMA_UART2_TX	0x06000020
+				SC_P_LVDS0_I2C1_SDA_DMA_UART2_RX	0x06000020
+			>;
+		};
+
+		/* Apalis UART2 */
+		pinctrl_lpuart3: lpuart3grp {
+			fsl,pins = <
+				SC_P_LVDS1_I2C1_SCL_DMA_UART3_TX	0x06000020
+				SC_P_LVDS1_I2C1_SDA_DMA_UART3_RX	0x06000020
+				SC_P_ENET1_RGMII_TXD3_DMA_UART3_RTS_B	0x06000020
+				SC_P_ENET1_RGMII_RXC_DMA_UART3_CTS_B	0x06000020
+			>;
+		};
+
+		/* Apalis PWM3 */
+		pinctrl_gpio_pwm0: gpiopwm0grp {
+			fsl,pins = <
+				SC_P_UART0_RTS_B_LSIO_GPIO0_IO22	0x00000021
+			>;
+		};
+
+		/* Apalis PWM4 */
+		pinctrl_gpio_pwm1: gpiopwm1grp {
+			fsl,pins = <
+				SC_P_UART0_CTS_B_LSIO_GPIO0_IO23	0x00000021
+			>;
+		};
+
+		/* Apalis PWM1 */
+		pinctrl_gpio_pwm2: gpiopwm2grp {
+			fsl,pins = <
+				SC_P_GPT1_COMPARE_LSIO_GPIO0_IO19	0x00000021
+			>;
+		};
+
+		/* Apalis PWM2 */
+		pinctrl_gpio_pwm3: gpiopwm3grp {
+			fsl,pins = <
+				SC_P_GPT0_COMPARE_LSIO_GPIO0_IO16	0x00000021
+			>;
+		};
+
+		/* Apalis BKL1_PWM */
+		pinctrl_gpio_pwm_bkl: gpiopwmbklgrp {
+			fsl,pins = <
+				SC_P_LVDS1_GPIO00_LVDS1_GPIO0_IO00	0x00000021
+			>;
+		};
+
+		/* Apalis USBH_EN */
+		pinctrl_gpio_usbh_en: gpiousbhen {
+			fsl,pins = <
+				SC_P_USB_SS3_TC1_LSIO_GPIO4_IO04	0x06000060
+			>;
+		};
+
+		/* Apalis USBH_OC# */
+		pinctrl_gpio_usbh_oc_n: gpiousbhocn {
+			fsl,pins = <
+				SC_P_USB_SS3_TC3_LSIO_GPIO4_IO06	0x06000060
+			>;
+		};
+
+		/* Apalis USBO1_EN */
+		pinctrl_gpio_usbo1_en: gpiousbo1en {
+			fsl,pins = <
+				SC_P_USB_SS3_TC0_LSIO_GPIO4_IO03	0x06000060
+			>;
+		};
+
+		/* Apalis USBO1_OC# */
+		pinctrl_gpio_usbo1_oc_n: gpiousbo1ocn {
+			fsl,pins = <
+				SC_P_USB_SS3_TC2_LSIO_GPIO4_IO05	0x06000060
+			>;
+		};
+
+		pinctrl_usdhc1: usdhc1grp {
+			fsl,pins = <
+				SC_P_EMMC0_CLK_CONN_EMMC0_CLK		0x06000041
+				SC_P_EMMC0_CMD_CONN_EMMC0_CMD		0x00000021
+				SC_P_EMMC0_DATA0_CONN_EMMC0_DATA0	0x00000021
+				SC_P_EMMC0_DATA1_CONN_EMMC0_DATA1	0x00000021
+				SC_P_EMMC0_DATA2_CONN_EMMC0_DATA2	0x00000021
+				SC_P_EMMC0_DATA3_CONN_EMMC0_DATA3	0x00000021
+				SC_P_EMMC0_DATA4_CONN_EMMC0_DATA4	0x00000021
+				SC_P_EMMC0_DATA5_CONN_EMMC0_DATA5	0x00000021
+				SC_P_EMMC0_DATA6_CONN_EMMC0_DATA6	0x00000021
+				SC_P_EMMC0_DATA7_CONN_EMMC0_DATA7	0x00000021
+				SC_P_EMMC0_STROBE_CONN_EMMC0_STROBE	0x06000041
+				SC_P_EMMC0_RESET_B_CONN_EMMC0_RESET_B	0x00000021
+			>;
+		};
+
+		pinctrl_sata1_act: sata1actgrp {
+			fsl,pins = <
+				/* Apalis SATA1_ACT# */
+				SC_P_ESAI1_TX0_LSIO_GPIO2_IO08		0x00000021
+			>;
+		};
+
+		pinctrl_mmc1_cd: mmc1cdgrp {
+			fsl,pins = <
+				/* Apalis MMC1_CD# */
+				SC_P_ESAI1_TX1_LSIO_GPIO2_IO09		0x00000021
+			>;
+		};
+
+		pinctrl_usdhc2: usdhc2grp {
+			fsl,pins = <
+				SC_P_USDHC1_CLK_CONN_USDHC1_CLK		0x06000041
+				SC_P_USDHC1_CMD_CONN_USDHC1_CMD		0x00000021
+				SC_P_USDHC1_DATA0_CONN_USDHC1_DATA0	0x00000021
+				SC_P_USDHC1_DATA1_CONN_USDHC1_DATA1	0x00000021
+				SC_P_USDHC1_DATA2_CONN_USDHC1_DATA2	0x00000021
+				SC_P_USDHC1_DATA3_CONN_USDHC1_DATA3	0x00000021
+				SC_P_USDHC1_DATA4_CONN_USDHC1_DATA4	0x00000021
+				SC_P_USDHC1_DATA5_CONN_USDHC1_DATA5	0x00000021
+				SC_P_USDHC1_DATA6_CONN_USDHC1_DATA6	0x00000021
+				SC_P_USDHC1_DATA7_CONN_USDHC1_DATA7	0x00000021
+				/* On-module PMIC use */
+				SC_P_USDHC1_VSELECT_CONN_USDHC1_VSELECT	0x00000021
+			>;
+		};
+
+		pinctrl_sd1_cd: sd1cdgrp {
+			fsl,pins = <
+				/* Apalis SD1_CD# */
+				SC_P_USDHC2_CD_B_LSIO_GPIO4_IO12	0x00000021
+			>;
+		};
+
+		pinctrl_usdhc3: usdhc3grp {
+			fsl,pins = <
+				SC_P_USDHC2_CLK_CONN_USDHC2_CLK		0x06000041
+				SC_P_USDHC2_CMD_CONN_USDHC2_CMD		0x00000021
+				SC_P_USDHC2_DATA0_CONN_USDHC2_DATA0	0x00000021
+				SC_P_USDHC2_DATA1_CONN_USDHC2_DATA1	0x00000021
+				SC_P_USDHC2_DATA2_CONN_USDHC2_DATA2	0x00000021
+				SC_P_USDHC2_DATA3_CONN_USDHC2_DATA3	0x00000021
+				/* On-module PMIC use */
+				SC_P_USDHC2_VSELECT_CONN_USDHC2_VSELECT	0x00000021
+			>;
+		};
+	};
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec1>;
+	fsl,magic-packet;
+	phy-handle = <&ethphy0>;
+	phy-mode = "rgmii";
+	phy-reset-duration = <10>;
+	phy-reset-gpios = <&gpio1 11 1>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@7 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <7>;
+		};
+	};
+};
+
+/* Apalis I2C2 (DDC) */
+&i2c0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpi2c0>;
+	clock-frequency = <100000>;
+	status = "okay";
+};
+
+/* On-module I2C */
+&i2c1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpi2c1>;
+	status = "okay";
+};
+
+/* Apalis I2C1 */
+&i2c2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpi2c2>;
+	status = "okay";
+};
+
+/* Apalis I2C3 (CAM) */
+&i2c3 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpi2c3>;
+	status = "okay";
+};
+
+/* Apalis UART3 */
+&lpuart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpuart0>;
+	status = "okay";
+};
+
+/* Apalis UART1 */
+&lpuart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpuart1>;
+	status = "okay";
+};
+
+/* Apalis UART4 */
+&lpuart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpuart2>;
+	status = "okay";
+};
+
+/* Apalis UART2 */
+&lpuart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpuart3>;
+	status = "okay";
+};
+
+/* eMMC */
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+/* Apalis MMC1 */
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_mmc1_cd>;
+	bus-width = <8>;
+	cd-gpios = <&gpio2 9 GPIO_ACTIVE_LOW>; /* Apalis MMC1_CD# */
+	status = "okay";
+};
+
+/* Apalis SD1 */
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>, <&pinctrl_sd1_cd>;
+	bus-width = <4>;
+	cd-gpios = <&gpio4 12 GPIO_ACTIVE_LOW>; /* Apalis SD1_CD# */
+	status = "okay";
+};

arch/arm/dts/fsl-imx8qm.dtsi

@@ -22,9 +22,18 @@
 		ethernet0 = &fec1;
 		ethernet1 = &fec2;
 		serial0 = &lpuart0;
+		serial1 = &lpuart1;
+		serial2 = &lpuart2;
+		serial3 = &lpuart3;
+		serial4 = &lpuart4;
 		mmc0 = &usdhc1;
 		mmc1 = &usdhc2;
 		mmc2 = &usdhc3;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
+		i2c3 = &i2c3;
+		i2c4 = &i2c4;
 	};
 
 	memory@80000000 {
@@ -193,9 +202,103 @@
 				power-domains = <&pd_dma>;
 				wakeup-irq = <345>;
 			};
+			pd_dma_lpuart1: PD_DMA_UART1 {
+				reg = <SC_R_UART_1>;
+				#power-domain-cells = <0>;
+				power-domains = <&pd_dma>;
+				wakeup-irq = <346>;
+			};
+			pd_dma_lpuart2: PD_DMA_UART2 {
+				reg = <SC_R_UART_2>;
+				#power-domain-cells = <0>;
+				power-domains = <&pd_dma>;
+				wakeup-irq = <347>;
+			};
+			pd_dma_lpuart3: PD_DMA_UART3 {
+				reg = <SC_R_UART_3>;
+				#power-domain-cells = <0>;
+				power-domains = <&pd_dma>;
+				wakeup-irq = <348>;
+			};
+			pd_dma_lpuart4: PD_DMA_UART4 {
+				reg = <SC_R_UART_4>;
+				#power-domain-cells = <0>;
+				power-domains = <&pd_dma>;
+				wakeup-irq = <349>;
+			};
 		};
 	};
 
+	i2c0: i2c@5a800000 {
+		compatible = "fsl,imx8qm-lpi2c", "fsl,imx7ulp-lpi2c";
+		reg = <0x0 0x5a800000 0x0 0x4000>;
+		interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-parent = <&gic>;
+		clocks = <&clk IMX8QM_I2C0_CLK>,
+			 <&clk IMX8QM_I2C0_IPG_CLK>;
+		clock-names = "per", "ipg";
+		assigned-clocks = <&clk IMX8QM_I2C0_CLK>;
+		assigned-clock-rates = <24000000>;
+		power-domains = <&pd_dma_lpi2c0>;
+		status = "disabled";
+	};
+
+	i2c1: i2c@5a810000 {
+		compatible = "fsl,imx8qm-lpi2c", "fsl,imx7ulp-lpi2c";
+		reg = <0x0 0x5a810000 0x0 0x4000>;
+		interrupts = <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-parent = <&gic>;
+		clocks = <&clk IMX8QM_I2C1_CLK>,
+			 <&clk IMX8QM_I2C1_IPG_CLK>;
+		clock-names = "per", "ipg";
+		assigned-clocks = <&clk IMX8QM_I2C1_CLK>;
+		assigned-clock-rates = <24000000>;
+		power-domains = <&pd_dma_lpi2c1>;
+		status = "disabled";
+	};
+
+	i2c2: i2c@5a820000 {
+		compatible = "fsl,imx8qm-lpi2c", "fsl,imx7ulp-lpi2c";
+		reg = <0x0 0x5a820000 0x0 0x4000>;
+		interrupts = <GIC_SPI 222 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-parent = <&gic>;
+		clocks = <&clk IMX8QM_I2C2_CLK>,
+			 <&clk IMX8QM_I2C2_IPG_CLK>;
+		clock-names = "per", "ipg";
+		assigned-clocks = <&clk IMX8QM_I2C2_CLK>;
+		assigned-clock-rates = <24000000>;
+		power-domains = <&pd_dma_lpi2c2>;
+		status = "disabled";
+	};
+
+	i2c3: i2c@5a830000 {
+		compatible = "fsl,imx8qm-lpi2c", "fsl,imx7ulp-lpi2c";
+		reg = <0x0 0x5a830000 0x0 0x4000>;
+		interrupts = <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-parent = <&gic>;
+		clocks = <&clk IMX8QM_I2C3_CLK>,
+			 <&clk IMX8QM_I2C3_IPG_CLK>;
+		clock-names = "per", "ipg";
+		assigned-clocks = <&clk IMX8QM_I2C3_CLK>;
+		assigned-clock-rates = <24000000>;
+		power-domains = <&pd_dma_lpi2c3>;
+		status = "disabled";
+	};
+
+	i2c4: i2c@5a840000 {
+		compatible = "fsl,imx8qm-lpi2c", "fsl,imx7ulp-lpi2c";
+		reg = <0x0 0x5a840000 0x0 0x4000>;
+		interrupts = <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-parent = <&gic>;
+		clocks = <&clk IMX8QM_I2C4_CLK>,
+			 <&clk IMX8QM_I2C4_IPG_CLK>;
+		clock-names = "per", "ipg";
+		assigned-clocks = <&clk IMX8QM_I2C4_CLK>;
+		assigned-clock-rates = <24000000>;
+		power-domains = <&pd_dma_lpi2c4>;
+		status = "disabled";
+	};
+
 	gpio0: gpio@5d080000 {
 		compatible = "fsl,imx8qm-gpio", "fsl,imx35-gpio";
 		reg = <0x0 0x5d080000 0x0 0x10000>;
@@ -297,6 +400,58 @@
 		status = "disabled";
 	};
 
+	lpuart1: serial@5a070000 {
+		compatible = "fsl,imx8qm-lpuart";
+		reg = <0x0 0x5a070000 0x0 0x1000>;
+		interrupts = <GIC_SPI 346 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&clk IMX8QM_UART1_CLK>,
+			 <&clk IMX8QM_UART1_IPG_CLK>;
+		clock-names = "per", "ipg";
+		assigned-clocks = <&clk IMX8QM_UART1_CLK>;
+		assigned-clock-rates = <80000000>;
+		power-domains = <&pd_dma_lpuart1>;
+		status = "disabled";
+	};
+
+	lpuart2: serial@5a080000 {
+		compatible = "fsl,imx8qm-lpuart";
+		reg = <0x0 0x5a080000 0x0 0x1000>;
+		interrupts = <GIC_SPI 347 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&clk IMX8QM_UART2_CLK>,
+			 <&clk IMX8QM_UART2_IPG_CLK>;
+		clock-names = "per", "ipg";
+		assigned-clocks = <&clk IMX8QM_UART2_CLK>;
+		assigned-clock-rates = <80000000>;
+		power-domains = <&pd_dma_lpuart2>;
+		status = "disabled";
+	};
+
+	lpuart3: serial@5a090000 {
+		compatible = "fsl,imx8qm-lpuart";
+		reg = <0x0 0x5a090000 0x0 0x1000>;
+		interrupts = <GIC_SPI 348 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&clk IMX8QM_UART3_CLK>,
+			 <&clk IMX8QM_UART3_IPG_CLK>;
+		clock-names = "per", "ipg";
+		assigned-clocks = <&clk IMX8QM_UART3_CLK>;
+		assigned-clock-rates = <80000000>;
+		power-domains = <&pd_dma_lpuart3>;
+		status = "disabled";
+	};
+
+	lpuart4: serial@5a0a0000 {
+		compatible = "fsl,imx8qm-lpuart";
+		reg = <0x0 0x5a0a0000 0x0 0x1000>;
+		interrupts = <GIC_SPI 349 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&clk IMX8QM_UART4_CLK>,
+			 <&clk IMX8QM_UART4_IPG_CLK>;
+		clock-names = "per", "ipg";
+		assigned-clocks = <&clk IMX8QM_UART4_CLK>;
+		assigned-clock-rates = <80000000>;
+		power-domains = <&pd_dma_lpuart4>;
+		status = "disabled";
+	};
+
 	usdhc1: usdhc@5b010000 {
 		compatible = "fsl,imx8qm-usdhc", "fsl,imx6sl-usdhc";
 		interrupt-parent = <&gic>;

arch/arm/dts/fsl-imx8qxp-colibri-u-boot.dtsi

@@ -0,0 +1,117 @@
+// SPDX-License-Identifier: GPL-2.0+ OR X11
+/*
+ * Copyright 2019 Toradex AG
+ */
+
+&{/imx8qx-pm} {
+
+	u-boot,dm-spl;
+};
+
+&mu {
+	u-boot,dm-spl;
+};
+
+&clk {
+	u-boot,dm-spl;
+};
+
+&iomuxc {
+	u-boot,dm-spl;
+};
+
+&pd_lsio {
+	u-boot,dm-spl;
+};
+
+&pd_lsio_gpio0 {
+	u-boot,dm-spl;
+};
+
+&pd_lsio_gpio1 {
+	u-boot,dm-spl;
+};
+
+&pd_lsio_gpio2 {
+	u-boot,dm-spl;
+};
+
+&pd_lsio_gpio3 {
+	u-boot,dm-spl;
+};
+
+&pd_lsio_gpio4 {
+	u-boot,dm-spl;
+};
+
+&pd_lsio_gpio5 {
+	u-boot,dm-spl;
+};
+
+&pd_lsio_gpio6 {
+	u-boot,dm-spl;
+};
+
+&pd_lsio_gpio7 {
+	u-boot,dm-spl;
+};
+
+&pd_conn {
+	u-boot,dm-spl;
+};
+
+&pd_conn_sdch0 {
+	u-boot,dm-spl;
+};
+
+&pd_conn_sdch1 {
+	u-boot,dm-spl;
+};
+
+&pd_conn_sdch2 {
+	u-boot,dm-spl;
+};
+
+&gpio0 {
+	u-boot,dm-spl;
+};
+
+&gpio1 {
+	u-boot,dm-spl;
+};
+
+&gpio2 {
+	u-boot,dm-spl;
+};
+
+&gpio3 {
+	u-boot,dm-spl;
+};
+
+&gpio4 {
+	u-boot,dm-spl;
+};
+
+&gpio5 {
+	u-boot,dm-spl;
+};
+
+&gpio6 {
+	u-boot,dm-spl;
+};
+
+&gpio7 {
+	u-boot,dm-spl;
+};
+
+&lpuart3 {
+	u-boot,dm-spl;
+};
+
+&usdhc1 {
+	u-boot,dm-spl;
+};
+
+&usdhc2 {
+	u-boot,dm-spl;
+};

arch/arm/dts/fsl-imx8qxp-colibri.dts

@@ -0,0 +1,328 @@
+// SPDX-License-Identifier: GPL-2.0+ OR X11
+/*
+ * Copyright 2019 Toradex AG
+ */
+
+/dts-v1/;
+
+#include "fsl-imx8qxp.dtsi"
+#include "fsl-imx8qxp-colibri-u-boot.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX8QXP";
+	compatible = "toradex,colibri-imx8qxp", "fsl,imx8qxp";
+
+	chosen {
+		bootargs = "console=ttyLP3,115200 earlycon=lpuart32,0x5a090000,115200";
+		stdout-path = &lpuart3;
+	};
+
+	reg_usbh_vbus: regulator-usbh-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbh1_reg>;
+		regulator-name = "usbh_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio4 3 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog0>, <&pinctrl_hog1>, <&pinctrl_hog2>;
+
+	colibri-imx8qxp {
+		pinctrl_lpuart0: lpuart0grp {
+			fsl,pins = <
+				SC_P_UART0_RX_ADMA_UART0_RX	0x06000020
+				SC_P_UART0_TX_ADMA_UART0_TX	0x06000020
+			>;
+		};
+
+		pinctrl_lpuart3: lpuart3grp {
+			fsl,pins = <
+				SC_P_FLEXCAN2_RX_ADMA_UART3_RX	0x06000020
+				SC_P_FLEXCAN2_TX_ADMA_UART3_TX	0x06000020
+			>;
+		};
+
+		pinctrl_lpuart3_ctrl: lpuart3ctrlgrp {
+			fsl,pins = <
+				SC_P_MIPI_DSI1_GPIO0_01_LSIO_GPIO2_IO00 0x00000020 /* DTR */
+				SC_P_SAI1_RXD_LSIO_GPIO0_IO29		0x00000020 /* CTS */
+				SC_P_SAI1_RXC_LSIO_GPIO0_IO30		0x00000020 /* RTS */
+				SC_P_CSI_RESET_LSIO_GPIO3_IO03		0x00000020 /* DSR */
+				SC_P_USDHC1_CD_B_LSIO_GPIO4_IO22	0x00000020 /* DCD */
+				SC_P_CSI_EN_LSIO_GPIO3_IO02		0x00000020 /* RI */
+			>;
+		};
+
+		pinctrl_fec1: fec1grp {
+			fsl,pins = <
+				SC_P_COMP_CTL_GPIO_1V8_3V3_ENET_ENETB0_PAD	0x000014a0 /* Use pads in 3.3V mode */
+				SC_P_COMP_CTL_GPIO_1V8_3V3_ENET_ENETB1_PAD	0x000014a0 /* Use pads in 3.3V mode */
+				SC_P_ENET0_MDC_CONN_ENET0_MDC			0x06000020
+				SC_P_ENET0_MDIO_CONN_ENET0_MDIO			0x06000020
+				SC_P_ENET0_RGMII_TX_CTL_CONN_ENET0_RGMII_TX_CTL	0x00000061
+				SC_P_ENET0_RGMII_TXC_CONN_ENET0_RCLK50M_OUT	0x06000061
+				SC_P_ENET0_RGMII_TXD0_CONN_ENET0_RGMII_TXD0	0x00000061
+				SC_P_ENET0_RGMII_TXD1_CONN_ENET0_RGMII_TXD1	0x00000061
+				SC_P_ENET0_RGMII_RX_CTL_CONN_ENET0_RGMII_RX_CTL	0x00000061
+				SC_P_ENET0_RGMII_RXD0_CONN_ENET0_RGMII_RXD0	0x00000061
+				SC_P_ENET0_RGMII_RXD1_CONN_ENET0_RGMII_RXD1	0x00000061
+				SC_P_ENET0_RGMII_RXD2_CONN_ENET0_RMII_RX_ER	0x00000061
+			>;
+		};
+
+		pinctrl_gpio_bl_on: gpio-bl-on {
+			fsl,pins = <
+				SC_P_QSPI0A_DATA3_LSIO_GPIO3_IO12	0x00000040
+			>;
+		};
+
+		pinctrl_hog0: hog0grp {
+			fsl,pins = <
+				SC_P_COMP_CTL_GPIO_1V8_3V3_GPIORHB_PAD	0x000514a0 /* Use pads in 3.3V mode */
+			>;
+		};
+
+		pinctrl_hog1: hog1grp {
+			fsl,pins = <
+				SC_P_QSPI0A_DATA1_LSIO_GPIO3_IO10	0x00000020 /*  45 */
+				SC_P_ENET0_RGMII_TXD3_LSIO_GPIO5_IO02	0x06000020 /*  65 */
+					SC_P_CSI_D07_CI_PI_D09		0x00000061
+				SC_P_QSPI0A_DATA2_LSIO_GPIO3_IO11	0x00000020 /*  69 */
+				SC_P_QSPI0A_DQS_LSIO_GPIO3_IO13		0x00000020 /*  73 */
+				SC_P_SAI0_TXC_LSIO_GPIO0_IO26		0x00000020 /*  79 */
+					SC_P_CSI_D02_CI_PI_D04		0x00000061
+				SC_P_ENET0_RGMII_RXC_LSIO_GPIO5_IO03	0x06000020 /*  85 */
+					SC_P_CSI_D06_CI_PI_D08		0x00000061
+				SC_P_QSPI0B_SCLK_LSIO_GPIO3_IO17	0x00000020 /*  95 */
+				SC_P_SAI0_RXD_LSIO_GPIO0_IO27		0x00000020 /*  97 */
+					SC_P_CSI_D03_CI_PI_D05		0x00000061
+				SC_P_QSPI0B_DATA0_LSIO_GPIO3_IO18	0x00000020 /*  99 */
+				SC_P_SAI0_TXFS_LSIO_GPIO0_IO28		0x00000020 /* 101 */
+					SC_P_CSI_D00_CI_PI_D02		0x00000061
+				SC_P_SAI0_TXD_LSIO_GPIO0_IO25		0x00000020 /* 103 */
+					SC_P_CSI_D01_CI_PI_D03		0x00000061
+				SC_P_QSPI0B_DATA1_LSIO_GPIO3_IO19	0x00000020 /* 105 */
+				SC_P_QSPI0B_DATA2_LSIO_GPIO3_IO20	0x00000020 /* 107 */
+				SC_P_USB_SS3_TC2_LSIO_GPIO4_IO05	0x00000020 /* 127 */
+				SC_P_USB_SS3_TC3_LSIO_GPIO4_IO06	0x00000020 /* 131 */
+				SC_P_USB_SS3_TC1_LSIO_GPIO4_IO04	0x00000020 /* 133 */
+				SC_P_CSI_PCLK_LSIO_GPIO3_IO00		0x00000020 /*  96 */
+				SC_P_QSPI0B_DATA3_LSIO_GPIO3_IO21	0x00000020 /*  98 */
+				SC_P_SAI1_RXFS_LSIO_GPIO0_IO31		0x00000020 /* 100 */
+				SC_P_QSPI0B_DQS_LSIO_GPIO3_IO22		0x00000020 /* 102 */
+				SC_P_QSPI0B_SS0_B_LSIO_GPIO3_IO23	0x00000020 /* 104 */
+				SC_P_QSPI0B_SS1_B_LSIO_GPIO3_IO24	0x00000020 /* 106 */
+			>;
+		};
+
+		pinctrl_hog2: hog2grp {
+			fsl,pins = <
+				SC_P_CSI_MCLK_LSIO_GPIO3_IO01		0x00000020 /*  75 */
+				SC_P_QSPI0A_SS0_B_LSIO_GPIO3_IO14	0x00000020 /*  77 */
+				SC_P_QSPI0A_SS1_B_LSIO_GPIO3_IO15	0x00000020 /*  89 */
+				SC_P_QSPI0A_SCLK_LSIO_GPIO3_IO16	0x00000020 /*  93 */
+			>;
+		};
+
+		/* Off Module I2C */
+		pinctrl_i2c1: i2c1grp {
+			fsl,pins = <
+				SC_P_MIPI_DSI0_GPIO0_00_ADMA_I2C1_SCL	0x06000021
+				SC_P_MIPI_DSI0_GPIO0_01_ADMA_I2C1_SDA	0x06000021
+			>;
+		};
+
+		/*INT*/
+		pinctrl_usb3503a: usb3503a-grp {
+			fsl,pins = <
+				SC_P_MIPI_CSI0_MCLK_OUT_LSIO_GPIO3_IO04 0x00000061
+			>;
+		};
+
+		pinctrl_usbc_det: usbc-det {
+			fsl,pins = <
+				SC_P_ENET0_REFCLK_125M_25M_LSIO_GPIO5_IO09	0x06000040
+			>;
+		};
+
+		pinctrl_usbh1_reg: usbh1-reg {
+			fsl,pins = <
+				SC_P_USB_SS3_TC0_LSIO_GPIO4_IO03	0x06000040
+			>;
+		};
+
+		pinctrl_usdhc1: usdhc1grp {
+			fsl,pins = <
+				SC_P_EMMC0_CLK_CONN_EMMC0_CLK		0x06000041
+				SC_P_EMMC0_CMD_CONN_EMMC0_CMD		0x00000021
+				SC_P_EMMC0_DATA0_CONN_EMMC0_DATA0	0x00000021
+				SC_P_EMMC0_DATA1_CONN_EMMC0_DATA1	0x00000021
+				SC_P_EMMC0_DATA2_CONN_EMMC0_DATA2	0x00000021
+				SC_P_EMMC0_DATA3_CONN_EMMC0_DATA3	0x00000021
+				SC_P_EMMC0_DATA4_CONN_EMMC0_DATA4	0x00000021
+				SC_P_EMMC0_DATA5_CONN_EMMC0_DATA5	0x00000021
+				SC_P_EMMC0_DATA6_CONN_EMMC0_DATA6	0x00000021
+				SC_P_EMMC0_DATA7_CONN_EMMC0_DATA7	0x00000021
+				SC_P_EMMC0_STROBE_CONN_EMMC0_STROBE	0x00000041
+				SC_P_EMMC0_RESET_B_CONN_EMMC0_RESET_B	0x00000021
+			>;
+		};
+
+		pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+			fsl,pins = <
+				SC_P_EMMC0_CLK_CONN_EMMC0_CLK		0x06000041
+				SC_P_EMMC0_CMD_CONN_EMMC0_CMD		0x00000021
+				SC_P_EMMC0_DATA0_CONN_EMMC0_DATA0	0x00000021
+				SC_P_EMMC0_DATA1_CONN_EMMC0_DATA1	0x00000021
+				SC_P_EMMC0_DATA2_CONN_EMMC0_DATA2	0x00000021
+				SC_P_EMMC0_DATA3_CONN_EMMC0_DATA3	0x00000021
+				SC_P_EMMC0_DATA4_CONN_EMMC0_DATA4	0x00000021
+				SC_P_EMMC0_DATA5_CONN_EMMC0_DATA5	0x00000021
+				SC_P_EMMC0_DATA6_CONN_EMMC0_DATA6	0x00000021
+				SC_P_EMMC0_DATA7_CONN_EMMC0_DATA7	0x00000021
+				SC_P_EMMC0_STROBE_CONN_EMMC0_STROBE	0x00000041
+				SC_P_EMMC0_RESET_B_CONN_EMMC0_RESET_B	0x00000021
+			>;
+		};
+
+		pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+			fsl,pins = <
+				SC_P_EMMC0_CLK_CONN_EMMC0_CLK		0x06000041
+				SC_P_EMMC0_CMD_CONN_EMMC0_CMD		0x00000021
+				SC_P_EMMC0_DATA0_CONN_EMMC0_DATA0	0x00000021
+				SC_P_EMMC0_DATA1_CONN_EMMC0_DATA1	0x00000021
+				SC_P_EMMC0_DATA2_CONN_EMMC0_DATA2	0x00000021
+				SC_P_EMMC0_DATA3_CONN_EMMC0_DATA3	0x00000021
+				SC_P_EMMC0_DATA4_CONN_EMMC0_DATA4	0x00000021
+				SC_P_EMMC0_DATA5_CONN_EMMC0_DATA5	0x00000021
+				SC_P_EMMC0_DATA6_CONN_EMMC0_DATA6	0x00000021
+				SC_P_EMMC0_DATA7_CONN_EMMC0_DATA7	0x00000021
+				SC_P_EMMC0_STROBE_CONN_EMMC0_STROBE	0x00000041
+				SC_P_EMMC0_RESET_B_CONN_EMMC0_RESET_B	0x00000021
+			>;
+		};
+
+		pinctrl_usdhc2_gpio: usdhc2gpiogrp {
+			fsl,pins = <
+				SC_P_QSPI0A_DATA0_LSIO_GPIO3_IO09	0x06000021
+			>;
+		};
+
+		pinctrl_usdhc2: usdhc2grp {
+			fsl,pins = <
+				SC_P_USDHC1_CLK_CONN_USDHC1_CLK		0x06000041
+				SC_P_USDHC1_CMD_CONN_USDHC1_CMD		0x00000021
+				SC_P_USDHC1_DATA0_CONN_USDHC1_DATA0	0x00000021
+				SC_P_USDHC1_DATA1_CONN_USDHC1_DATA1	0x00000021
+				SC_P_USDHC1_DATA2_CONN_USDHC1_DATA2	0x00000021
+				SC_P_USDHC1_DATA3_CONN_USDHC1_DATA3	0x00000021
+				SC_P_USDHC1_VSELECT_CONN_USDHC1_VSELECT	0x00000021
+			>;
+		};
+
+		pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+			fsl,pins = <
+				SC_P_USDHC1_CLK_CONN_USDHC1_CLK		0x06000041
+				SC_P_USDHC1_CMD_CONN_USDHC1_CMD		0x00000021
+				SC_P_USDHC1_DATA0_CONN_USDHC1_DATA0	0x00000021
+				SC_P_USDHC1_DATA1_CONN_USDHC1_DATA1	0x00000021
+				SC_P_USDHC1_DATA2_CONN_USDHC1_DATA2	0x00000021
+				SC_P_USDHC1_DATA3_CONN_USDHC1_DATA3	0x00000021
+				SC_P_USDHC1_VSELECT_CONN_USDHC1_VSELECT	0x00000021
+			>;
+		};
+
+		pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+			fsl,pins = <
+				SC_P_USDHC1_CLK_CONN_USDHC1_CLK		0x06000041
+				SC_P_USDHC1_CMD_CONN_USDHC1_CMD		0x00000021
+				SC_P_USDHC1_DATA0_CONN_USDHC1_DATA0	0x00000021
+				SC_P_USDHC1_DATA1_CONN_USDHC1_DATA1	0x00000021
+				SC_P_USDHC1_DATA2_CONN_USDHC1_DATA2	0x00000021
+				SC_P_USDHC1_DATA3_CONN_USDHC1_DATA3	0x00000021
+				SC_P_USDHC1_VSELECT_CONN_USDHC1_VSELECT	0x00000021
+			>;
+		};
+	};
+};
+
+&lpuart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpuart0>;
+	status = "okay";
+};
+
+&lpuart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpuart3>, <&pinctrl_lpuart3_ctrl>;
+	status = "okay";
+};
+
+&gpio0 {
+	status = "okay";
+};
+
+&gpio1 {
+	status = "okay";
+};
+
+&gpio3 {
+	status = "okay";
+};
+
+&gpio4 {
+	status = "okay";
+};
+
+&fec1 {
+	phy-handle = <&ethphy0>;
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec1>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@2 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			max-speed = <100>;
+			reg = <2>;
+		};
+	};
+};
+
+&i2c1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+};
+
+&usdhc1 {
+	bus-width = <8>;
+	non-removable;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+	status = "okay";
+};
+
+&usdhc2 {
+	bus-width = <4>;
+	cd-gpios = <&gpio3 9 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+	status = "okay";
+};

arch/arm/dts/fsl-ls1028a.dtsi

@@ -108,6 +108,17 @@
 		       0x82000000 0x0 0x40000000 0x88 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
 	};
 
+	pcie@1f0000000 {
+		compatible = "pci-host-ecam-generic";
+		/* ECAM bus 0, HW has more space reserved but not populated */
+		bus-range = <0x0 0x0>;
+		reg = <0x01 0xf0000000 0x0 0x100000>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+		device_type = "pci";
+		ranges= <0x82000000 0x0 0x00000000 0x1 0xf8000000 0x0 0x160000>;
+	};
+
 	i2c0: i2c@2000000 {
 		compatible = "fsl,vf610-i2c";
 		#address-cells = <1>;
@@ -272,9 +283,10 @@
 
 	sata: sata@3200000 {
 		compatible = "fsl,ls1028a-ahci";
-		reg = <0x0 0x3200000 0x0 0x10000>;
+		reg = <0x0 0x3200000 0x0 0x10000	/* ccsr sata base */
+		       0x7 0x100520  0x0 0x4>;		/* ecc sata addr*/
+		reg-names = "sata-base", "ecc-addr";
 		interrupts = <0 133 4>;
-		clocks = <&clockgen 4 1>;
 		status = "disabled";
 	};
 

arch/arm/dts/fsl-ls1046a-frwy.dts

@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: GPL-2.0+ OR X11
+/*
+ * Device Tree Include file for NXP Layerscape-1046A family SoC.
+ *
+ * Copyright 2019 NXP
+ *
+ */
+
+/dts-v1/;
+/include/ "fsl-ls1046a.dtsi"
+
+/ {
+	model = "LS1046A FRWY Board";
+
+	aliases {
+		spi0 = &qspi;
+	};
+
+};
+
+&qspi {
+	bus-num = <0>;
+	status = "okay";
+
+	qflash0: mt25qu512abb8esf@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "spi-flash";
+		spi-max-frequency = <50000000>;
+		reg = <0>;
+	};
+
+};
+

arch/arm/dts/fsl-lx2160a-qds.dts

@@ -15,3 +15,26 @@
 	compatible = "fsl,lx2160aqds", "fsl,lx2160a";
 };
 
+&esdhc0 {
+	status = "okay";
+};
+
+&esdhc1 {
+	status = "okay";
+};
+
+&sata0 {
+	status = "okay";
+};
+
+&sata1 {
+	status = "okay";
+};
+
+&sata2 {
+	status = "okay";
+};
+
+&sata3 {
+	status = "okay";
+};

arch/arm/dts/imx53-m53.dtsi

@@ -0,0 +1,132 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2014 Marek Vasut <marex@denx.de>
+ */
+
+#include "imx53.dtsi"
+
+/ {
+	model = "Aries/DENX M53";
+	compatible = "aries,imx53-m53", "denx,imx53-m53", "fsl,imx53";
+
+	memory@70000000 {
+		device_type = "memory";
+		reg = <0x70000000 0x20000000>,
+		      <0xb0000000 0x20000000>;
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		reg_3p2v: regulator@0 {
+			compatible = "regulator-fixed";
+			reg = <0>;
+			regulator-name = "3P2V";
+			regulator-min-microvolt = <3200000>;
+			regulator-max-microvolt = <3200000>;
+			regulator-always-on;
+		};
+
+		reg_backlight: regulator@1 {
+			compatible = "regulator-fixed";
+			reg = <1>;
+			regulator-name = "lcd-supply";
+			regulator-min-microvolt = <3200000>;
+			regulator-max-microvolt = <3200000>;
+			regulator-always-on;
+		};
+	};
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	clock-frequency = <400000>;
+	status = "okay";
+
+	touchscreen@41 {
+		compatible = "st,stmpe610";
+		reg = <0x41>;
+		id = <0>;
+		blocks = <0x5>;
+		interrupts = <6 0x0>;
+		interrupt-parent = <&gpio7>;
+		irq-trigger = <0x1>;
+
+		stmpe_touchscreen {
+			compatible = "st,stmpe-ts";
+			st,sample-time = <4>;
+			st,mod-12b = <1>;
+			st,ref-sel = <0>;
+			st,adc-freq = <1>;
+			st,ave-ctrl = <3>;
+			st,touch-det-delay = <3>;
+			st,settling = <4>;
+			st,fraction-z = <7>;
+			st,i-drive = <1>;
+		};
+	};
+
+	eeprom: eeprom@50 {
+		compatible = "atmel,24c128";
+		reg = <0x50>;
+		pagesize = <32>;
+	};
+
+	rtc: rtc@68 {
+		compatible = "st,m41t62";
+		reg = <0x68>;
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	imx53-m53evk {
+		pinctrl_hog: hoggrp {
+			fsl,pins = <
+				MX53_PAD_GPIO_0__CCM_SSI_EXT1_CLK	0x80000000
+				MX53_PAD_EIM_EB3__GPIO2_31		0x80000000
+				MX53_PAD_PATA_DA_0__GPIO7_6		0x80000000
+			>;
+		};
+
+		pinctrl_i2c2: i2c2grp {
+			fsl,pins = <
+				MX53_PAD_EIM_D16__I2C2_SDA		0xc0000000
+				MX53_PAD_EIM_EB2__I2C2_SCL		0xc0000000
+			>;
+		};
+
+		pinctrl_nand: nandgrp {
+			fsl,pins = <
+				MX53_PAD_NANDF_WE_B__EMI_NANDF_WE_B	0x4
+				MX53_PAD_NANDF_RE_B__EMI_NANDF_RE_B	0x4
+				MX53_PAD_NANDF_CLE__EMI_NANDF_CLE	0x4
+				MX53_PAD_NANDF_ALE__EMI_NANDF_ALE	0x4
+				MX53_PAD_NANDF_WP_B__EMI_NANDF_WP_B	0xe0
+				MX53_PAD_NANDF_RB0__EMI_NANDF_RB_0	0xe0
+				MX53_PAD_NANDF_CS0__EMI_NANDF_CS_0	0x4
+				MX53_PAD_PATA_DATA0__EMI_NANDF_D_0	0xa4
+				MX53_PAD_PATA_DATA1__EMI_NANDF_D_1	0xa4
+				MX53_PAD_PATA_DATA2__EMI_NANDF_D_2	0xa4
+				MX53_PAD_PATA_DATA3__EMI_NANDF_D_3	0xa4
+				MX53_PAD_PATA_DATA4__EMI_NANDF_D_4	0xa4
+				MX53_PAD_PATA_DATA5__EMI_NANDF_D_5	0xa4
+				MX53_PAD_PATA_DATA6__EMI_NANDF_D_6	0xa4
+				MX53_PAD_PATA_DATA7__EMI_NANDF_D_7	0xa4
+			>;
+		};
+	};
+};
+
+&nfc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_nand>;
+	nand-bus-width = <8>;
+	nand-ecc-mode = "hw";
+	status = "okay";
+};

arch/arm/dts/imx53-m53menlo-u-boot.dtsi

@@ -0,0 +1,42 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2019 Marek Vasut <marex@denx.de>
+ */
+
+/ {
+	soc {
+		u-boot,dm-pre-reloc;
+
+		aips@50000000 {
+			u-boot,dm-pre-reloc;
+		};
+	};
+};
+
+&gpio1 {
+	u-boot,dm-pre-reloc;
+};
+
+&gpio2 {
+	u-boot,dm-pre-reloc;
+};
+
+&gpio3 {
+	u-boot,dm-pre-reloc;
+};
+
+&gpio4 {
+	u-boot,dm-pre-reloc;
+};
+
+&gpio5 {
+	u-boot,dm-pre-reloc;
+};
+
+&gpio6 {
+	u-boot,dm-pre-reloc;
+};
+
+&gpio7 {
+	u-boot,dm-pre-reloc;
+};

arch/arm/dts/imx53-m53menlo.dts

@@ -0,0 +1,312 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2019 Marek Vasut <marex@denx.de>
+ */
+
+/dts-v1/;
+#include "imx53-m53.dtsi"
+#include "imx53-m53menlo-u-boot.dtsi"
+
+/ {
+	model = "MENLO M53 EMBEDDED DEVICE";
+	compatible = "menlo,m53menlo", "fsl,imx53";
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_led>;
+
+		user1 {
+			label = "TestLed601";
+			gpios = <&gpio6 1 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc0";
+		};
+
+		user2 {
+			label = "TestLed602";
+			gpios = <&gpio6 2 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		eth {
+			label = "EthLedYe";
+			gpios = <&gpio2 11 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "none";
+		};
+	};
+
+	panel {
+		compatible = "edt,etm070080dh6";
+		enable-gpios = <&gpio6 0 GPIO_ACTIVE_HIGH>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&lvds0_out>;
+			};
+		};
+	};
+
+	reg_usbh1_vbus: regulator-usbh1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 2 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1>;
+	status = "okay";
+};
+
+&can2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can2>;
+	status = "okay";
+};
+
+&clks {
+	assigned-clocks = <&clks IMX5_CLK_CKO1_SEL>,
+			  <&clks IMX5_CLK_CKO1_PODF>,
+			  <&clks IMX5_CLK_CKO1>;
+	assigned-clock-parents = <&clks IMX5_CLK_AHB>;
+	assigned-clock-rates = <133333334>, <33333334>, <33333334>;
+};
+
+&esdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_esdhc1>;
+	cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec>;
+	phy-mode = "rmii";
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	touchscreen@38 {
+		compatible = "edt,edt-ft5x06";
+		reg = <0x38>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_edt_ft5x06>;
+		interrupt-parent = <&gpio6>;
+		interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&gpio2 9 GPIO_ACTIVE_LOW>;
+		wake-gpios = <&gpio2 10 GPIO_ACTIVE_HIGH>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+		pagesize = <32>;
+	};
+
+	dac@60 {
+		compatible = "microchip,mcp4725";
+		reg = <0x60>;
+	};
+};
+
+&i2c2 {
+	touchscreen@41 {
+		status = "disabled";
+	};
+};
+
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	imx53-m53evk {
+		hoggrp {
+			fsl,pins = <
+				MX53_PAD_GPIO_0__CCM_SSI_EXT1_CLK	0x1c4
+				MX53_PAD_EIM_EB3__GPIO2_31		0x1d5
+				MX53_PAD_PATA_DA_0__GPIO7_6		0x1d5
+				MX53_PAD_GPIO_19__CCM_CLKO		0x1d5
+				MX53_PAD_CSI0_MCLK__CCM_CSI0_MCLK	0x1d5
+				MX53_PAD_CSI0_DAT4__GPIO5_22		0x1d5
+				MX53_PAD_CSI0_DAT5__GPIO5_23		0x1d5
+				MX53_PAD_CSI0_DAT6__GPIO5_24		0x1d5
+				MX53_PAD_CSI0_DAT7__GPIO5_25		0x1d5
+				MX53_PAD_CSI0_DAT8__GPIO5_26		0x1d5
+				MX53_PAD_CSI0_DAT9__GPIO5_27		0x1d5
+				MX53_PAD_CSI0_DAT10__GPIO5_28		0x1d5
+				MX53_PAD_CSI0_DAT11__GPIO5_29		0x1d5
+				MX53_PAD_CSI0_DAT14__GPIO6_0		0x1d5
+			>;
+		};
+
+		pinctrl_led: ledgrp {
+			fsl,pins = <
+				MX53_PAD_CSI0_DAT15__GPIO6_1		0x1d5
+				MX53_PAD_CSI0_DAT16__GPIO6_2		0x1d5
+			>;
+		};
+
+		pinctrl_can1: can1grp {
+			fsl,pins = <
+				MX53_PAD_GPIO_7__CAN1_TXCAN		0x1c4
+				MX53_PAD_GPIO_8__CAN1_RXCAN		0x1c4
+			>;
+		};
+
+		pinctrl_can2: can2grp {
+			fsl,pins = <
+				MX53_PAD_KEY_COL4__CAN2_TXCAN		0x1c4
+				MX53_PAD_KEY_ROW4__CAN2_RXCAN		0x1c4
+			>;
+		};
+
+		pinctrl_display_gpio: display-gpiogrp {
+			fsl,pins = <
+				MX53_PAD_CSI0_DAT12__GPIO5_30		0x1d5 /* Reset */
+				MX53_PAD_CSI0_DAT13__GPIO5_31		0x1d5 /* Interrupt */
+			>;
+		};
+
+		pinctrl_edt_ft5x06: edt-ft5x06grp {
+			fsl,pins = <
+				MX53_PAD_PATA_DATA9__GPIO2_9		0x1d5 /* Reset */
+				MX53_PAD_CSI0_DAT19__GPIO6_5		0x1d5 /* Interrupt */
+				MX53_PAD_PATA_DATA10__GPIO2_10		0x1d5 /* Wake */
+			>;
+		};
+
+		pinctrl_esdhc1: esdhc1grp {
+			fsl,pins = <
+				MX53_PAD_SD1_DATA0__ESDHC1_DAT0		0x1d5
+				MX53_PAD_SD1_DATA1__ESDHC1_DAT1		0x1d5
+				MX53_PAD_SD1_DATA2__ESDHC1_DAT2		0x1d5
+				MX53_PAD_SD1_DATA3__ESDHC1_DAT3		0x1d5
+				MX53_PAD_SD1_CMD__ESDHC1_CMD		0x1d5
+				MX53_PAD_SD1_CLK__ESDHC1_CLK		0x1d5
+			>;
+		};
+
+		pinctrl_fec: fecgrp {
+			fsl,pins = <
+				MX53_PAD_FEC_MDC__FEC_MDC		0x4
+				MX53_PAD_FEC_MDIO__FEC_MDIO		0x1fc
+				MX53_PAD_FEC_REF_CLK__FEC_TX_CLK	0x180
+				MX53_PAD_FEC_RX_ER__FEC_RX_ER		0x180
+				MX53_PAD_FEC_CRS_DV__FEC_RX_DV		0x180
+				MX53_PAD_FEC_RXD1__FEC_RDATA_1		0x180
+				MX53_PAD_FEC_RXD0__FEC_RDATA_0		0x180
+				MX53_PAD_FEC_TX_EN__FEC_TX_EN		0x4
+				MX53_PAD_FEC_TXD1__FEC_TDATA_1		0x4
+				MX53_PAD_FEC_TXD0__FEC_TDATA_0		0x4
+			>;
+		};
+
+		pinctrl_i2c1: i2c1grp {
+			fsl,pins = <
+				MX53_PAD_EIM_D21__I2C1_SCL		0x400001e4
+				MX53_PAD_EIM_D28__I2C1_SDA		0x400001e4
+			>;
+		};
+
+		pinctrl_i2c3: i2c3grp {
+			fsl,pins = <
+				MX53_PAD_GPIO_6__I2C3_SDA		0x400001e4
+				MX53_PAD_GPIO_5__I2C3_SCL		0x400001e4
+			>;
+		};
+
+		pinctrl_lvds0: lvds0grp {
+			/* LVDS pins only have pin mux configuration */
+			fsl,pins = <
+				MX53_PAD_LVDS0_CLK_P__LDB_LVDS0_CLK	0x80000000
+				MX53_PAD_LVDS0_TX0_P__LDB_LVDS0_TX0	0x80000000
+				MX53_PAD_LVDS0_TX1_P__LDB_LVDS0_TX1	0x80000000
+				MX53_PAD_LVDS0_TX2_P__LDB_LVDS0_TX2	0x80000000
+				MX53_PAD_LVDS0_TX3_P__LDB_LVDS0_TX3	0x80000000
+			>;
+		};
+
+		pinctrl_uart1: uart1grp {
+			fsl,pins = <
+				MX53_PAD_PATA_DIOW__UART1_TXD_MUX	0x1e4
+				MX53_PAD_PATA_DMACK__UART1_RXD_MUX	0x1e4
+			>;
+		};
+
+		pinctrl_uart2: uart2grp {
+			fsl,pins = <
+				MX53_PAD_PATA_BUFFER_EN__UART2_RXD_MUX	0x1e4
+				MX53_PAD_PATA_DMARQ__UART2_TXD_MUX	0x1e4
+			>;
+		};
+
+		pinctrl_usb: usbgrp {
+			fsl,pins = <
+				MX53_PAD_GPIO_2__GPIO1_2		0x1d5
+				MX53_PAD_GPIO_3__USBOH3_USBH1_OC	0x1d5
+			>;
+		};
+	};
+};
+
+&ldb {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lvds0>;
+	status = "okay";
+
+	lvds0: lvds-channel@0 {
+		reg = <0>;
+		fsl,data-mapping = "spwg";
+		fsl,data-width = <18>;
+		status = "okay";
+
+		port@2 {
+			reg = <2>;
+
+			lvds0_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&usbh1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb>;
+	vbus-supply = <&reg_usbh1_vbus>;
+	phy_type = "utmi";
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usbotg {
+	dr_mode = "peripheral";
+	status = "okay";
+};

arch/arm/dts/imx53.dtsi

@@ -1,17 +1,8 @@
-/*
- * Copyright 2016 Beckhoff Automation
- * Copyright 2011 Freescale Semiconductor, Inc.
- * Copyright 2011 Linaro Ltd.
- *
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 or later at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
- */
+// SPDX-License-Identifier: GPL-2.0+
+//
+// Copyright 2011 Freescale Semiconductor, Inc.
+// Copyright 2011 Linaro Ltd.
 
-#include "skeleton.dtsi"
 #include "imx53-pinfunc.h"
 #include <dt-bindings/clock/imx5-clock.h>
 #include <dt-bindings/gpio/gpio.h>
@@ -19,8 +10,17 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 
 / {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	/*
+	 * The decompressor and also some bootloaders rely on a
+	 * pre-existing /chosen node to be available to insert the
+	 * command line and merge other ATAGS info.
+	 */
+	chosen {};
+
 	aliases {
-		serial1 = &uart2;
+		ethernet0 = &fec;
 		gpio0 = &gpio1;
 		gpio1 = &gpio2;
 		gpio2 = &gpio3;
@@ -36,7 +36,45 @@
 		mmc1 = &esdhc2;
 		mmc2 = &esdhc3;
 		mmc3 = &esdhc4;
-		usb1 = &usbh1;
+		serial0 = &uart1;
+		serial1 = &uart2;
+		serial2 = &uart3;
+		serial3 = &uart4;
+		serial4 = &uart5;
+		spi0 = &ecspi1;
+		spi1 = &ecspi2;
+		spi2 = &cspi;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a8";
+			reg = <0x0>;
+			clocks = <&clks IMX5_CLK_ARM>;
+			clock-latency = <61036>;
+			voltage-tolerance = <5>;
+			operating-points = <
+				/* kHz */
+				 166666  850000
+				 400000  900000
+				 800000 1050000
+				1000000 1200000
+				1200000 1300000
+			>;
+		};
+	};
+
+	display-subsystem {
+		compatible = "fsl,imx-display-subsystem";
+		ports = <&ipu_di0>, <&ipu_di1>;
+	};
+
+	capture_subsystem {
+		compatible = "fsl,imx-capture-subsystem";
+		ports = <&ipu_csi0>, <&ipu_csi1>;
 	};
 
 	tzic: tz-interrupt-controller@fffc000 {
@@ -46,13 +84,143 @@
 		reg = <0x0fffc000 0x4000>;
 	};
 
+	clocks {
+		ckil {
+			compatible = "fsl,imx-ckil", "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+		};
+
+		ckih1 {
+			compatible = "fsl,imx-ckih1", "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <22579200>;
+		};
+
+		ckih2 {
+			compatible = "fsl,imx-ckih2", "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <0>;
+		};
+
+		osc {
+			compatible = "fsl,imx-osc", "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <24000000>;
+		};
+	};
+
+	pmu: pmu {
+		compatible = "arm,cortex-a8-pmu";
+		interrupt-parent = <&tzic>;
+		interrupts = <77>;
+	};
+
+	usbphy0: usbphy-0 {
+		compatible = "usb-nop-xceiv";
+		clocks = <&clks IMX5_CLK_USB_PHY1_GATE>;
+		clock-names = "main_clk";
+		#phy-cells = <0>;
+		status = "okay";
+	};
+
+	usbphy1: usbphy-1 {
+		compatible = "usb-nop-xceiv";
+		clocks = <&clks IMX5_CLK_USB_PHY2_GATE>;
+		clock-names = "main_clk";
+		#phy-cells = <0>;
+		status = "okay";
+	};
+
 	soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "simple-bus";
 		interrupt-parent = <&tzic>;
 		ranges;
-		u-boot,dm-pre-reloc;
+
+		sata: sata@10000000 {
+			compatible = "fsl,imx53-ahci";
+			reg = <0x10000000 0x1000>;
+			interrupts = <28>;
+			clocks = <&clks IMX5_CLK_SATA_GATE>,
+				 <&clks IMX5_CLK_SATA_REF>,
+				 <&clks IMX5_CLK_AHB>;
+			clock-names = "sata", "sata_ref", "ahb";
+			status = "disabled";
+		};
+
+		ipu: ipu@18000000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "fsl,imx53-ipu";
+			reg = <0x18000000 0x08000000>;
+			interrupts = <11 10>;
+			clocks = <&clks IMX5_CLK_IPU_GATE>,
+				 <&clks IMX5_CLK_IPU_DI0_GATE>,
+				 <&clks IMX5_CLK_IPU_DI1_GATE>;
+			clock-names = "bus", "di0", "di1";
+			resets = <&src 2>;
+
+			ipu_csi0: port@0 {
+				reg = <0>;
+
+				ipu_csi0_from_parallel_sensor: endpoint {
+				};
+			};
+
+			ipu_csi1: port@1 {
+				reg = <1>;
+
+				ipu_csi1_from_parallel_sensor: endpoint {
+				};
+			};
+
+			ipu_di0: port@2 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <2>;
+
+				ipu_di0_disp0: endpoint@0 {
+					reg = <0>;
+				};
+
+				ipu_di0_lvds0: endpoint@1 {
+					reg = <1>;
+					remote-endpoint = <&lvds0_in>;
+				};
+			};
+
+			ipu_di1: port@3 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <3>;
+
+				ipu_di1_disp1: endpoint@0 {
+					reg = <0>;
+				};
+
+				ipu_di1_lvds1: endpoint@1 {
+					reg = <1>;
+					remote-endpoint = <&lvds1_in>;
+				};
+
+				ipu_di1_tve: endpoint@2 {
+					reg = <2>;
+					remote-endpoint = <&tve_in>;
+				};
+			};
+		};
+
+		gpu: gpu@30000000 {
+			compatible = "amd,imageon-200.0", "amd,imageon";
+			reg = <0x30000000 0x20000>;
+			reg-names = "kgsl_3d0_reg_memory";
+			interrupts = <12>;
+			interrupt-names = "kgsl_3d0_irq";
+			clocks = <&clks IMX5_CLK_GPU3D_GATE>, <&clks IMX5_CLK_GARB_GATE>;
+			clock-names = "core_clk", "mem_iface_clk";
+		};
 
 		aips@50000000 { /* AIPS1 */
 			compatible = "fsl,aips-bus", "simple-bus";
@@ -92,6 +260,47 @@
 					status = "disabled";
 				};
 
+				uart3: serial@5000c000 {
+					compatible = "fsl,imx53-uart", "fsl,imx21-uart";
+					reg = <0x5000c000 0x4000>;
+					interrupts = <33>;
+					clocks = <&clks IMX5_CLK_UART3_IPG_GATE>,
+						 <&clks IMX5_CLK_UART3_PER_GATE>;
+					clock-names = "ipg", "per";
+					dmas = <&sdma 42 4 0>, <&sdma 43 4 0>;
+					dma-names = "rx", "tx";
+					status = "disabled";
+				};
+
+				ecspi1: spi@50010000 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					compatible = "fsl,imx53-ecspi", "fsl,imx51-ecspi";
+					reg = <0x50010000 0x4000>;
+					interrupts = <36>;
+					clocks = <&clks IMX5_CLK_ECSPI1_IPG_GATE>,
+						 <&clks IMX5_CLK_ECSPI1_PER_GATE>;
+					clock-names = "ipg", "per";
+					status = "disabled";
+				};
+
+				ssi2: ssi@50014000 {
+					#sound-dai-cells = <0>;
+					compatible = "fsl,imx53-ssi",
+							"fsl,imx51-ssi",
+							"fsl,imx21-ssi";
+					reg = <0x50014000 0x4000>;
+					interrupts = <30>;
+					clocks = <&clks IMX5_CLK_SSI2_IPG_GATE>,
+						 <&clks IMX5_CLK_SSI2_ROOT_GATE>;
+					clock-names = "ipg", "baud";
+					dmas = <&sdma 24 1 0>,
+					       <&sdma 25 1 0>;
+					dma-names = "rx", "tx";
+					fsl,fifo-depth = <15>;
+					status = "disabled";
+				};
+
 				esdhc3: esdhc@50020000 {
 					compatible = "fsl,imx53-esdhc";
 					reg = <0x50020000 0x4000>;
@@ -117,25 +326,18 @@
 				};
 			};
 
-			iomuxc: iomuxc@53fa8000 {
-				compatible = "fsl,imx53-iomuxc";
-				reg = <0x53fa8000 0x4000>;
+			aipstz1: bridge@53f00000 {
+				compatible = "fsl,imx53-aipstz";
+				reg = <0x53f00000 0x60>;
 			};
 
-			gpr: iomuxc-gpr@53fa8000 {
-				compatible = "fsl,imx53-iomuxc-gpr", "syscon";
-				reg = <0x53fa8000 0xc>;
-			};
-
-			uart2: serial@53fc0000 {
-				compatible = "fsl,imx7d-uart", "fsl,imx53-uart", "fsl,imx21-uart";
-				reg = <0x53fc0000 0x4000>;
-				interrupts = <32>;
-				clocks = <&clks IMX5_CLK_UART2_IPG_GATE>,
-				         <&clks IMX5_CLK_UART2_PER_GATE>;
-				clock-names = "ipg", "per";
-				dmas = <&sdma 12 4 0>, <&sdma 13 4 0>;
-				dma-names = "rx", "tx";
+			usbotg: usb@53f80000 {
+				compatible = "fsl,imx53-usb", "fsl,imx27-usb";
+				reg = <0x53f80000 0x0200>;
+				interrupts = <18>;
+				clocks = <&clks IMX5_CLK_USBOH3_GATE>;
+				fsl,usbmisc = <&usbmisc 0>;
+				fsl,usbphy = <&usbphy0>;
 				status = "disabled";
 			};
 
@@ -144,15 +346,37 @@
 				reg = <0x53f80200 0x0200>;
 				interrupts = <14>;
 				clocks = <&clks IMX5_CLK_USBOH3_GATE>;
+				fsl,usbmisc = <&usbmisc 1>;
+				fsl,usbphy = <&usbphy1>;
 				dr_mode = "host";
 				status = "disabled";
 			};
 
-			clks: ccm@53fd4000{
-				compatible = "fsl,imx53-ccm";
-				reg = <0x53fd4000 0x4000>;
-				interrupts = <0 71 0x04 0 72 0x04>;
-				#clock-cells = <1>;
+			usbh2: usb@53f80400 {
+				compatible = "fsl,imx53-usb", "fsl,imx27-usb";
+				reg = <0x53f80400 0x0200>;
+				interrupts = <16>;
+				clocks = <&clks IMX5_CLK_USBOH3_GATE>;
+				fsl,usbmisc = <&usbmisc 2>;
+				dr_mode = "host";
+				status = "disabled";
+			};
+
+			usbh3: usb@53f80600 {
+				compatible = "fsl,imx53-usb", "fsl,imx27-usb";
+				reg = <0x53f80600 0x0200>;
+				interrupts = <17>;
+				clocks = <&clks IMX5_CLK_USBOH3_GATE>;
+				fsl,usbmisc = <&usbmisc 3>;
+				dr_mode = "host";
+				status = "disabled";
+			};
+
+			usbmisc: usbmisc@53f80800 {
+				#index-cells = <1>;
+				compatible = "fsl,imx53-usbmisc";
+				reg = <0x53f80800 0x200>;
+				clocks = <&clks IMX5_CLK_USBOH3_GATE>;
 			};
 
 			gpio1: gpio@53f84000 {
@@ -195,177 +419,56 @@
 				#interrupt-cells = <2>;
 			};
 
-			gpio5: gpio@53fdc000 {
-				compatible = "fsl,imx53-gpio", "fsl,imx35-gpio";
-				reg = <0x53fdc000 0x4000>;
-				interrupts = <103 104>;
-				gpio-controller;
-				#gpio-cells = <2>;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-			};
-
-			gpio6: gpio@53fe0000 {
-				compatible = "fsl,imx53-gpio", "fsl,imx35-gpio";
-				reg = <0x53fe0000 0x4000>;
-				interrupts = <105 106>;
-				gpio-controller;
-				#gpio-cells = <2>;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-			};
-
-			gpio7: gpio@53fe4000 {
-				compatible = "fsl,imx53-gpio", "fsl,imx35-gpio";
-				reg = <0x53fe4000 0x4000>;
-				interrupts = <107 108>;
-				gpio-controller;
-				#gpio-cells = <2>;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-			};
-
-			i2c3: i2c@53fec000 {
-				#address-cells = <1>;
-				#size-cells = <0>;
-				compatible = "fsl,imx53-i2c", "fsl,imx21-i2c";
-				reg = <0x53fec000 0x4000>;
-				interrupts = <64>;
-				clocks = <&clks IMX5_CLK_I2C3_GATE>;
-				status = "disabled";
-			};
-		};
-
-		aips@60000000 {	/* AIPS2 */
-			compatible = "fsl,aips-bus", "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			reg = <0x60000000 0x10000000>;
-			ranges;
-
-			sdma: sdma@63fb0000 {
-				compatible = "fsl,imx53-sdma", "fsl,imx35-sdma";
-				reg = <0x63fb0000 0x4000>;
-				interrupts = <6>;
-				clocks = <&clks IMX5_CLK_SDMA_GATE>,
-				         <&clks IMX5_CLK_SDMA_GATE>;
-				clock-names = "ipg", "ahb";
-				#dma-cells = <3>;
-				fsl,sdma-ram-script-name = "imx/sdma/sdma-imx53.bin";
-			};
-
-			fec: ethernet@63fec000 {
-				compatible = "fsl,imx53-fec", "fsl,imx25-fec";
-				reg = <0x63fec000 0x4000>;
-				interrupts = <87>;
-				clocks = <&clks IMX5_CLK_FEC_GATE>,
-				         <&clks IMX5_CLK_FEC_GATE>,
-				         <&clks IMX5_CLK_FEC_GATE>;
-				clock-names = "ipg", "ahb", "ptp";
+			kpp: kpp@53f94000 {
+				compatible = "fsl,imx53-kpp", "fsl,imx21-kpp";
+				reg = <0x53f94000 0x4000>;
+				interrupts = <60>;
+				clocks = <&clks IMX5_CLK_DUMMY>;
 				status = "disabled";
 			};
 
-			i2c2: i2c@63fc4000 {
-				#address-cells = <1>;
-				#size-cells = <0>;
-				compatible = "fsl,imx53-i2c", "fsl,imx21-i2c";
-				reg = <0x63fc4000 0x4000>;
-				interrupts = <63>;
-				clocks = <&clks IMX5_CLK_I2C2_GATE>;
+			wdog1: wdog@53f98000 {
+				compatible = "fsl,imx53-wdt", "fsl,imx21-wdt";
+				reg = <0x53f98000 0x4000>;
+				interrupts = <58>;
+				clocks = <&clks IMX5_CLK_DUMMY>;
+			};
+
+			wdog2: wdog@53f9c000 {
+				compatible = "fsl,imx53-wdt", "fsl,imx21-wdt";
+				reg = <0x53f9c000 0x4000>;
+				interrupts = <59>;
+				clocks = <&clks IMX5_CLK_DUMMY>;
 				status = "disabled";
 			};
 
-			i2c1: i2c@63fc8000 {
-				#address-cells = <1>;
-				#size-cells = <0>;
-				compatible = "fsl,imx53-i2c", "fsl,imx21-i2c";
-				reg = <0x63fc8000 0x4000>;
-				interrupts = <62>;
-				clocks = <&clks IMX5_CLK_I2C1_GATE>;
-				status = "disabled";
-			};
-		};
-
-		ipu: ipu@18000000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "fsl,imx53-ipu";
-			reg = <0x18000000 0x08000000>;
-			interrupts = <11 10>;
-			clocks = <&clks IMX5_CLK_IPU_GATE>,
-				 <&clks IMX5_CLK_IPU_DI0_GATE>,
-				 <&clks IMX5_CLK_IPU_DI1_GATE>;
-			clock-names = "bus", "di0", "di1";
-			resets = <&src 2>;
-			u-boot,dm-pre-reloc;
-
-			ipu_csi0: port@0 {
-				reg = <0>;
+			gpt: timer@53fa0000 {
+				compatible = "fsl,imx53-gpt", "fsl,imx31-gpt";
+				reg = <0x53fa0000 0x4000>;
+				interrupts = <39>;
+				clocks = <&clks IMX5_CLK_GPT_IPG_GATE>,
+					 <&clks IMX5_CLK_GPT_HF_GATE>;
+				clock-names = "ipg", "per";
 			};
 
-			ipu_csi1: port@1 {
-				reg = <1>;
+			srtc: rtc@53fa4000 {
+				compatible = "fsl,imx53-rtc";
+				reg = <0x53fa4000 0x4000>;
+				interrupts = <24>;
+				clocks = <&clks IMX5_CLK_SRTC_GATE>;
 			};
 
-			ipu_di0: port@2 {
-				#address-cells = <1>;
-				#size-cells = <0>;
-				reg = <2>;
-
-				ipu_di0_disp0: endpoint@0 {
-					reg = <0>;
-				};
-
-				ipu_di0_lvds0: endpoint@1 {
-					reg = <1>;
-					remote-endpoint = <&lvds0_in>;
-				};
+			iomuxc: iomuxc@53fa8000 {
+				compatible = "fsl,imx53-iomuxc";
+				reg = <0x53fa8000 0x4000>;
 			};
 
-			ipu_di1: port@3 {
-				#address-cells = <1>;
-				#size-cells = <0>;
-				reg = <3>;
-
-				ipu_di1_disp1: endpoint@0 {
-					reg = <0>;
-				};
-
-				ipu_di1_lvds1: endpoint@1 {
-					reg = <1>;
-					remote-endpoint = <&lvds1_in>;
-				};
-
-				ipu_di1_tve: endpoint@2 {
-					reg = <2>;
-					remote-endpoint = <&tve_in>;
-				};
+			gpr: iomuxc-gpr@53fa8000 {
+				compatible = "fsl,imx53-iomuxc-gpr", "syscon";
+				reg = <0x53fa8000 0xc>;
 			};
-		};
 
-		tve: tve@63ff0000 {
-				compatible = "fsl,imx53-tve";
-				reg = <0x63ff0000 0x1000>;
-				interrupts = <92>;
-				clocks = <&clks IMX5_CLK_TVE_GATE>,
-					 <&clks IMX5_CLK_IPU_DI1_SEL>;
-				clock-names = "tve", "di_sel";
-				status = "disabled";
-
-				port {
-					tve_in: endpoint {
-						remote-endpoint = <&ipu_di1_tve>;
-					};
-				};
-		};
-
-		src: src@53fd0000 {
-				compatible = "fsl,imx53-src", "fsl,imx51-src";
-				reg = <0x53fd0000 0x4000>;
-				#reset-cells = <1>;
-		};
-
-		ldb: ldb@53fa8008 {
+			ldb: ldb@53fa8008 {
 				#address-cells = <1>;
 				#size-cells = <0>;
 				compatible = "fsl,imx53-ldb";
@@ -419,6 +522,334 @@
 						reg = <2>;
 					};
 				};
+			};
+
+			pwm1: pwm@53fb4000 {
+				#pwm-cells = <2>;
+				compatible = "fsl,imx53-pwm", "fsl,imx27-pwm";
+				reg = <0x53fb4000 0x4000>;
+				clocks = <&clks IMX5_CLK_PWM1_IPG_GATE>,
+					 <&clks IMX5_CLK_PWM1_HF_GATE>;
+				clock-names = "ipg", "per";
+				interrupts = <61>;
+			};
+
+			pwm2: pwm@53fb8000 {
+				#pwm-cells = <2>;
+				compatible = "fsl,imx53-pwm", "fsl,imx27-pwm";
+				reg = <0x53fb8000 0x4000>;
+				clocks = <&clks IMX5_CLK_PWM2_IPG_GATE>,
+					 <&clks IMX5_CLK_PWM2_HF_GATE>;
+				clock-names = "ipg", "per";
+				interrupts = <94>;
+			};
+
+			uart1: serial@53fbc000 {
+				compatible = "fsl,imx53-uart", "fsl,imx21-uart";
+				reg = <0x53fbc000 0x4000>;
+				interrupts = <31>;
+				clocks = <&clks IMX5_CLK_UART1_IPG_GATE>,
+					 <&clks IMX5_CLK_UART1_PER_GATE>;
+				clock-names = "ipg", "per";
+				dmas = <&sdma 18 4 0>, <&sdma 19 4 0>;
+				dma-names = "rx", "tx";
+				status = "disabled";
+			};
+
+			uart2: serial@53fc0000 {
+				compatible = "fsl,imx53-uart", "fsl,imx21-uart";
+				reg = <0x53fc0000 0x4000>;
+				interrupts = <32>;
+				clocks = <&clks IMX5_CLK_UART2_IPG_GATE>,
+					 <&clks IMX5_CLK_UART2_PER_GATE>;
+				clock-names = "ipg", "per";
+				dmas = <&sdma 12 4 0>, <&sdma 13 4 0>;
+				dma-names = "rx", "tx";
+				status = "disabled";
+			};
+
+			can1: can@53fc8000 {
+				compatible = "fsl,imx53-flexcan", "fsl,imx25-flexcan";
+				reg = <0x53fc8000 0x4000>;
+				interrupts = <82>;
+				clocks = <&clks IMX5_CLK_CAN1_IPG_GATE>,
+					 <&clks IMX5_CLK_CAN1_SERIAL_GATE>;
+				clock-names = "ipg", "per";
+				status = "disabled";
+			};
+
+			can2: can@53fcc000 {
+				compatible = "fsl,imx53-flexcan", "fsl,imx25-flexcan";
+				reg = <0x53fcc000 0x4000>;
+				interrupts = <83>;
+				clocks = <&clks IMX5_CLK_CAN2_IPG_GATE>,
+					 <&clks IMX5_CLK_CAN2_SERIAL_GATE>;
+				clock-names = "ipg", "per";
+				status = "disabled";
+			};
+
+			src: src@53fd0000 {
+				compatible = "fsl,imx53-src", "fsl,imx51-src";
+				reg = <0x53fd0000 0x4000>;
+				#reset-cells = <1>;
+			};
+
+			clks: ccm@53fd4000{
+				compatible = "fsl,imx53-ccm";
+				reg = <0x53fd4000 0x4000>;
+				interrupts = <0 71 0x04 0 72 0x04>;
+				#clock-cells = <1>;
+			};
+
+			gpio5: gpio@53fdc000 {
+				compatible = "fsl,imx53-gpio", "fsl,imx35-gpio";
+				reg = <0x53fdc000 0x4000>;
+				interrupts = <103 104>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+			};
+
+			gpio6: gpio@53fe0000 {
+				compatible = "fsl,imx53-gpio", "fsl,imx35-gpio";
+				reg = <0x53fe0000 0x4000>;
+				interrupts = <105 106>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+			};
+
+			gpio7: gpio@53fe4000 {
+				compatible = "fsl,imx53-gpio", "fsl,imx35-gpio";
+				reg = <0x53fe4000 0x4000>;
+				interrupts = <107 108>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+			};
+
+			i2c3: i2c@53fec000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "fsl,imx53-i2c", "fsl,imx21-i2c";
+				reg = <0x53fec000 0x4000>;
+				interrupts = <64>;
+				clocks = <&clks IMX5_CLK_I2C3_GATE>;
+				status = "disabled";
+			};
+
+			uart4: serial@53ff0000 {
+				compatible = "fsl,imx53-uart", "fsl,imx21-uart";
+				reg = <0x53ff0000 0x4000>;
+				interrupts = <13>;
+				clocks = <&clks IMX5_CLK_UART4_IPG_GATE>,
+					 <&clks IMX5_CLK_UART4_PER_GATE>;
+				clock-names = "ipg", "per";
+				dmas = <&sdma 2 4 0>, <&sdma 3 4 0>;
+				dma-names = "rx", "tx";
+				status = "disabled";
+			};
+		};
+
+		aips@60000000 {	/* AIPS2 */
+			compatible = "fsl,aips-bus", "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x60000000 0x10000000>;
+			ranges;
+
+			aipstz2: bridge@63f00000 {
+				compatible = "fsl,imx53-aipstz";
+				reg = <0x63f00000 0x60>;
+			};
+
+			iim: iim@63f98000 {
+				compatible = "fsl,imx53-iim", "fsl,imx27-iim";
+				reg = <0x63f98000 0x4000>;
+				interrupts = <69>;
+				clocks = <&clks IMX5_CLK_IIM_GATE>;
+			};
+
+			uart5: serial@63f90000 {
+				compatible = "fsl,imx53-uart", "fsl,imx21-uart";
+				reg = <0x63f90000 0x4000>;
+				interrupts = <86>;
+				clocks = <&clks IMX5_CLK_UART5_IPG_GATE>,
+					 <&clks IMX5_CLK_UART5_PER_GATE>;
+				clock-names = "ipg", "per";
+				dmas = <&sdma 16 4 0>, <&sdma 17 4 0>;
+				dma-names = "rx", "tx";
+				status = "disabled";
+			};
+
+			tigerp: tigerp@63fa0000 {
+				compatible = "fsl,imx53-tigerp", "fsl,imx51-tigerp";
+				reg = <0x63fa0000 0x28>;
+			};
+
+			owire: owire@63fa4000 {
+				compatible = "fsl,imx53-owire", "fsl,imx21-owire";
+				reg = <0x63fa4000 0x4000>;
+				clocks = <&clks IMX5_CLK_OWIRE_GATE>;
+				status = "disabled";
+			};
+
+			ecspi2: spi@63fac000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "fsl,imx53-ecspi", "fsl,imx51-ecspi";
+				reg = <0x63fac000 0x4000>;
+				interrupts = <37>;
+				clocks = <&clks IMX5_CLK_ECSPI2_IPG_GATE>,
+					 <&clks IMX5_CLK_ECSPI2_PER_GATE>;
+				clock-names = "ipg", "per";
+				status = "disabled";
+			};
+
+			sdma: sdma@63fb0000 {
+				compatible = "fsl,imx53-sdma", "fsl,imx35-sdma";
+				reg = <0x63fb0000 0x4000>;
+				interrupts = <6>;
+				clocks = <&clks IMX5_CLK_SDMA_GATE>,
+					 <&clks IMX5_CLK_AHB>;
+				clock-names = "ipg", "ahb";
+				#dma-cells = <3>;
+				fsl,sdma-ram-script-name = "imx/sdma/sdma-imx53.bin";
+			};
+
+			cspi: spi@63fc0000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "fsl,imx53-cspi", "fsl,imx35-cspi";
+				reg = <0x63fc0000 0x4000>;
+				interrupts = <38>;
+				clocks = <&clks IMX5_CLK_CSPI_IPG_GATE>,
+					 <&clks IMX5_CLK_CSPI_IPG_GATE>;
+				clock-names = "ipg", "per";
+				status = "disabled";
+			};
+
+			i2c2: i2c@63fc4000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "fsl,imx53-i2c", "fsl,imx21-i2c";
+				reg = <0x63fc4000 0x4000>;
+				interrupts = <63>;
+				clocks = <&clks IMX5_CLK_I2C2_GATE>;
+				status = "disabled";
+			};
+
+			i2c1: i2c@63fc8000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "fsl,imx53-i2c", "fsl,imx21-i2c";
+				reg = <0x63fc8000 0x4000>;
+				interrupts = <62>;
+				clocks = <&clks IMX5_CLK_I2C1_GATE>;
+				status = "disabled";
+			};
+
+			ssi1: ssi@63fcc000 {
+				#sound-dai-cells = <0>;
+				compatible = "fsl,imx53-ssi", "fsl,imx51-ssi",
+						"fsl,imx21-ssi";
+				reg = <0x63fcc000 0x4000>;
+				interrupts = <29>;
+				clocks = <&clks IMX5_CLK_SSI1_IPG_GATE>,
+					 <&clks IMX5_CLK_SSI1_ROOT_GATE>;
+				clock-names = "ipg", "baud";
+				dmas = <&sdma 28 0 0>,
+				       <&sdma 29 0 0>;
+				dma-names = "rx", "tx";
+				fsl,fifo-depth = <15>;
+				status = "disabled";
+			};
+
+			audmux: audmux@63fd0000 {
+				compatible = "fsl,imx53-audmux", "fsl,imx31-audmux";
+				reg = <0x63fd0000 0x4000>;
+				status = "disabled";
+			};
+
+			nfc: nand@63fdb000 {
+				compatible = "fsl,imx53-nand";
+				reg = <0x63fdb000 0x1000 0xf7ff0000 0x10000>;
+				interrupts = <8>;
+				clocks = <&clks IMX5_CLK_NFC_GATE>;
+				status = "disabled";
+			};
+
+			ssi3: ssi@63fe8000 {
+				#sound-dai-cells = <0>;
+				compatible = "fsl,imx53-ssi", "fsl,imx51-ssi",
+						"fsl,imx21-ssi";
+				reg = <0x63fe8000 0x4000>;
+				interrupts = <96>;
+				clocks = <&clks IMX5_CLK_SSI3_IPG_GATE>,
+					 <&clks IMX5_CLK_SSI3_ROOT_GATE>;
+				clock-names = "ipg", "baud";
+				dmas = <&sdma 46 0 0>,
+				       <&sdma 47 0 0>;
+				dma-names = "rx", "tx";
+				fsl,fifo-depth = <15>;
+				status = "disabled";
+			};
+
+			fec: ethernet@63fec000 {
+				compatible = "fsl,imx53-fec", "fsl,imx25-fec";
+				reg = <0x63fec000 0x4000>;
+				interrupts = <87>;
+				clocks = <&clks IMX5_CLK_FEC_GATE>,
+					 <&clks IMX5_CLK_FEC_GATE>,
+					 <&clks IMX5_CLK_FEC_GATE>;
+				clock-names = "ipg", "ahb", "ptp";
+				status = "disabled";
+			};
+
+			tve: tve@63ff0000 {
+				compatible = "fsl,imx53-tve";
+				reg = <0x63ff0000 0x1000>;
+				interrupts = <92>;
+				clocks = <&clks IMX5_CLK_TVE_GATE>,
+					 <&clks IMX5_CLK_IPU_DI1_SEL>;
+				clock-names = "tve", "di_sel";
+				status = "disabled";
+
+				port {
+					tve_in: endpoint {
+						remote-endpoint = <&ipu_di1_tve>;
+					};
+				};
+			};
+
+			vpu: vpu@63ff4000 {
+				compatible = "fsl,imx53-vpu", "cnm,coda7541";
+				reg = <0x63ff4000 0x1000>;
+				interrupts = <9>;
+				clocks = <&clks IMX5_CLK_VPU_REFERENCE_GATE>,
+					 <&clks IMX5_CLK_VPU_GATE>;
+				clock-names = "per", "ahb";
+				resets = <&src 1>;
+				iram = <&ocram>;
+			};
+
+			sahara: crypto@63ff8000 {
+				compatible = "fsl,imx53-sahara";
+				reg = <0x63ff8000 0x4000>;
+				interrupts = <19 20>;
+				clocks = <&clks IMX5_CLK_SAHARA_IPG_GATE>,
+					 <&clks IMX5_CLK_SAHARA_IPG_GATE>;
+				clock-names = "ipg", "ahb";
+			};
+		};
+
+		ocram: sram@f8000000 {
+			compatible = "mmio-sram";
+			reg = <0xf8000000 0x20000>;
+			clocks = <&clks IMX5_CLK_OCRAM>;
 		};
 	};
 };

arch/arm/dts/imx6-logicpd-baseboard.dtsi

@@ -1,45 +1,6 @@
-/*
- * Copyright 2018 Logic PD, Inc.
- * Based on SabreSD, Copyright 2016 Freescale Semiconductor, Inc.
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of the
- *     License, or (at your option) any later version.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2019 Logic PD, Inc.
 
 / {
 	keyboard {
@@ -68,6 +29,7 @@
 			debounce-interval = <10>;
 			wakeup-source;
 		};
+
 		btn3 {
 			gpios = <&pcf8575 3 GPIO_ACTIVE_LOW>;
 			label = "btn3";
@@ -81,7 +43,7 @@
 	leds {
 		compatible = "gpio-leds";
 
-		gen_led0 {
+		gen-led0 {
 			label = "led0";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_led0>;
@@ -89,25 +51,27 @@
 			linux,default-trigger = "cpu0";
 		};
 
-		gen_led1 {
+		gen-led1 {
 			label = "led1";
 			gpios = <&pcf8575 8 GPIO_ACTIVE_HIGH>;
 		};
 
-		gen_led2 {
+		gen-led2 {
 			label = "led2";
 			gpios = <&pcf8575 9 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
 
-		gen_led3 {
+		gen-led3 {
 			label = "led3";
 			gpios = <&pcf8575 10 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "default-on";
 		};
 	};
 
-	reg_usb_otg_vbus: regulator-otg-vbus@0 {
+	reg_usb_otg_vbus: regulator-otg-vbus {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usb_otg>;
 		compatible = "regulator-fixed";
 		regulator-name = "usb_otg_vbus";
 		regulator-min-microvolt = <5000000>;
@@ -116,14 +80,19 @@
 		enable-active-high;
 	};
 
-	reg_usb_h1_vbus: regulator-usbh1vbus@1 {
+	reg_usb_h1_vbus: regulator-usb-h1-vbus {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usb_h1_vbus>;
 		compatible = "regulator-fixed";
 		regulator-name = "usb_h1_vbus";
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <70000>;
+		enable-active-high;
 	};
 
-	reg_3v3: regulator-3v3@2 {
+	reg_3v3: regulator-3v3 {
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_reg_3v3>;
 		compatible = "regulator-fixed";
@@ -131,13 +100,14 @@
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 		gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <70000>;
 		enable-active-high;
 		regulator-always-on;
 	};
 
-	reg_enet: regulator-ethernet@3 {
+	reg_enet: regulator-ethernet {
 		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_enet_pwr>;
+		pinctrl-0 = <&pinctrl_reg_enet>;
 		compatible = "regulator-fixed";
 		regulator-name = "ethernet-supply";
 		regulator-min-microvolt = <3300000>;
@@ -148,7 +118,7 @@
 		vin-supply = <&sw4_reg>;
 	};
 
-	reg_audio: regulator-audio@4 {
+	reg_audio: regulator-audio {
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_reg_audio>;
 		compatible = "regulator-fixed";
@@ -157,11 +127,10 @@
 		regulator-max-microvolt = <3300000>;
 		gpio = <&gpio1 29 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
-		regulator-always-on;
 		vin-supply = <&reg_3v3>;
 	};
 
-	reg_hdmi: regulator-hdmi@5 {
+	reg_hdmi: regulator-hdmi {
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_reg_hdmi>;
 		compatible = "regulator-fixed";
@@ -173,7 +142,7 @@
 		vin-supply = <&reg_3v3>;
 	};
 
-	reg_uart3: regulator-uart3@6 {
+	reg_uart3: regulator-uart3 {
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_reg_uart3>;
 		compatible = "regulator-fixed";
@@ -184,7 +153,7 @@
 		vin-supply = <&reg_3v3>;
 	};
 
-	reg_1v8: regulator-1v8@7 {
+	reg_1v8: regulator-1v8 {
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_reg_1v8>;
 		compatible = "regulator-fixed";
@@ -195,21 +164,21 @@
 		vin-supply = <&reg_3v3>;
 	};
 
-	reg_pcie: regulator@8 {
+	reg_pcie: regulator-pcie {
 		compatible = "regulator-fixed";
 		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_pcie_reg>;
-		regulator-name = "MPCIE_3V3";
+		pinctrl-0 = <&pinctrl_reg_pcie>;
+		regulator-name = "mpcie_3v3";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 		gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
 	};
 
-	mipi_pwr: regulator@9 {
+	reg_mipi: regulator-mipi {
 		compatible = "regulator-fixed";
 		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_mipi_pwr>;
+		pinctrl-0 = <&pinctrl_reg_mipi>;
 		regulator-name = "mipi_pwr_en";
 		regulator-min-microvolt = <2800000>;
 		regulator-max-microvolt = <2800000>;
@@ -221,7 +190,7 @@
 		compatible = "fsl,imx-audio-wm8962";
 		model = "wm8962-audio";
 		ssi-controller = <&ssi2>;
-		audio-codec = <&codec>;
+		audio-codec = <&wm8962>;
 		audio-routing =
 			"Headphone Jack", "HPOUTL",
 			"Headphone Jack", "HPOUTR",
@@ -246,34 +215,10 @@
 	status = "disabled";
 };
 
-&pwm3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pwm3>;
-};
-
-&uart3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart3>;
-	status = "okay";
-};
-
-&usbh1 {
-	vbus-supply = <&reg_usb_h1_vbus>;
-	status = "okay";
-};
-
-&usbotg {
-	vbus-supply = <&reg_usb_otg_vbus>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usbotg>;
-	disable-over-current;
-	status = "okay";
-};
-
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-reset-duration = <10>;
 	phy-reset-gpios = <&gpio1 24 GPIO_ACTIVE_LOW>;
 	phy-supply = <&reg_enet>;
@@ -282,23 +227,13 @@
 	status = "okay";
 };
 
-&usdhc2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc2>;
-	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
-	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
-	no-1-8-v;
-	keep-power-in-suspend;
-	status = "okay";
-};
-
 &i2c1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c1>;
 	clock-frequency = <400000>;
 	status = "okay";
 
-	codec: wm8962@1a {
+	wm8962: audio-codec@1a {
 		compatible = "wlf,wm8962";
 		reg = <0x1a>;
 		clocks = <&clks IMX6QDL_CLK_CKO>;
@@ -330,9 +265,9 @@
 		reg = <0x10>;
 		clocks = <&clks IMX6QDL_CLK_CKO>;
 		clock-names = "xclk";
-		DOVDD-supply = <&mipi_pwr>;
-		AVDD-supply = <&mipi_pwr>;
-		DVDD-supply = <&mipi_pwr>;
+		DOVDD-supply = <&reg_mipi>;
+		AVDD-supply = <&reg_mipi>;
+		DVDD-supply = <&reg_mipi>;
 		reset-gpios = <&gpio3 26 GPIO_ACTIVE_LOW>;
 		powerdown-gpios = <&gpio3 27 GPIO_ACTIVE_HIGH>;
 
@@ -361,6 +296,11 @@
 	};
 };
 
+&ipu1_csi1_from_mipi_vc1 {
+	clock-lanes = <0>;
+	data-lanes = <1 2>;
+};
+
 &mipi_csi {
 	status = "okay";
 
@@ -379,17 +319,52 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pcie>;
 	reset-gpio = <&gpio1 9 GPIO_ACTIVE_LOW>;
-	status = "okay";
 	vpcie-supply = <&reg_pcie>;
-	/* fsl,max-link-speed = <2>; */
+	status = "okay";
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>;
 };
 
 &ssi2 {
 	status = "okay";
 };
 
-&iomuxc {
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
 
+&usbh1 {
+	vbus-supply = <&reg_usb_h1_vbus>;
+	status = "okay";
+};
+
+&usbotg {
+	vbus-supply = <&reg_usb_otg_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	disable-over-current;
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+	vmmc-supply = <&reg_3v3>;
+	no-1-8-v;
+	keep-power-in-suspend;
+	cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&iomuxc {
 	pinctrl_audmux: audmuxgrp {
 		fsl,pins = <
 			MX6QDL_PAD_DISP0_DAT20__AUD4_TXC  0x130b0
@@ -399,21 +374,49 @@
 		>;
 	};
 
-	pinctrl_i2c1: i2c1 {
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL0__ECSPI1_SCLK	0x100b1
+			MX6QDL_PAD_KEY_ROW0__ECSPI1_MOSI	0x100b1
+			MX6QDL_PAD_KEY_COL1__ECSPI1_MISO	0x100b1
+			MX6QDL_PAD_KEY_ROW1__ECSPI1_SS0		0x100b1
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b8b0
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b030
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b030
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b030
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b030
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b030
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x100b0
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b030
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x4001b0a8
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x13030
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x13030
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x13030
+			MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25	0x1b0b0	/* ENET_INT */
+			MX6QDL_PAD_ENET_RX_ER__GPIO1_IO24	0x1b0b0	/* ETHR_nRST */
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
 		fsl,pins = <
 			MX6QDL_PAD_EIM_D21__I2C1_SCL	0x4001b8b1
 			MX6QDL_PAD_EIM_D28__I2C1_SDA	0x4001b8b1
 		>;
 	};
 
-	pinctrl_enet_pwr: enet_pwr {
-		fsl,pins = <
-			MX6QDL_PAD_EIM_D31__GPIO3_IO31	0x1b0b0
-		>;
-	};
-
-	pinctrl_mipi_pwr: pwr_mipi {
-		fsl,pins = <MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x1b0b1>;
+	pinctrl_led0: led0grp {
+	    fsl,pins = <
+		MX6QDL_PAD_ENET_TXD0__GPIO1_IO30	0x1b0b0
+	    >;
 	};
 
 	pinctrl_ov5640: ov5640grp {
@@ -423,12 +426,83 @@
 		>;
 	};
 
-	pinctrl_reg_hdmi: reg_hdmi {
+	pinctrl_pcf8574: pcf8575grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_BCLK__GPIO6_IO31 0x1b0b0
+		>;
+	};
+
+	pinctrl_pcie: pciegrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
+			MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x1b0b0
+		>;
+	};
+
+	pinctrl_pwm3: pwm3grp {
+	    fsl,pins = <
+		MX6QDL_PAD_SD4_DAT1__PWM3_OUT		0x1b0b1
+	    >;
+	};
+
+	pinctrl_reg_1v8: reg1v8grp {
+	    fsl,pins = <
+		MX6QDL_PAD_EIM_D30__GPIO3_IO30		0x1b0b0
+	    >;
+	};
+
+	pinctrl_reg_3v3: reg3v3grp {
+	    fsl,pins = <
+		MX6QDL_PAD_ENET_RXD1__GPIO1_IO26	0x1b0b0
+	    >;
+	};
+
+	pinctrl_reg_audio: reg-audiogrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x1b0b0
+		>;
+	};
+
+	pinctrl_reg_enet: reg-enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D31__GPIO3_IO31	0x1b0b0
+		>;
+	};
+
+	pinctrl_reg_hdmi: reg-hdmigrp {
 		fsl,pins = <
 			MX6QDL_PAD_EIM_D20__GPIO3_IO20	0x1b0b0
 		>;
 	};
 
+	pinctrl_reg_mipi: reg-mipigrp {
+		fsl,pins = <MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x1b0b1>;
+	};
+
+	pinctrl_reg_pcie: reg-pciegrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02	0x1b0b0
+			>;
+	};
+
+	pinctrl_reg_uart3: reguart3grp {
+	    fsl,pins = <
+		MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28	0x1b0b0
+	    >;
+	};
+
+	pinctrl_reg_usb_h1_vbus: usbh1grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_17__GPIO7_IO12		0x1b0b0
+		>;
+	};
+
+	pinctrl_reg_usb_otg: reg-usb-otggrp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW4__GPIO4_IO15		0x1b0b0
+		>;
+	};
+
 	pinctrl_uart3: uart3grp {
 		fsl,pins = <
 			MX6QDL_PAD_EIM_D23__UART3_CTS_B		0x1b0b1
@@ -441,16 +515,6 @@
 	pinctrl_usbotg: usbotggrp {
 		fsl,pins = <
 			MX6QDL_PAD_GPIO_1__USB_OTG_ID	0xd17059
-			MX6QDL_PAD_KEY_ROW4__USB_OTG_PWR 0x130b0
-		>;
-	};
-
-	pinctrl_ecspi1: ecspi1grp {
-		fsl,pins = <
-			MX6QDL_PAD_KEY_COL0__ECSPI1_SCLK	0x100b1
-			MX6QDL_PAD_KEY_ROW0__ECSPI1_MOSI	0x100b1
-			MX6QDL_PAD_KEY_COL1__ECSPI1_MISO	0x100b1
-			MX6QDL_PAD_KEY_ROW1__ECSPI1_SS0		0x100b1
 		>;
 	};
 
@@ -490,107 +554,4 @@
 		>;
 	};
 
-	pinctrl_enet: enetgrp {
-		fsl,pins = <
-			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b8b0
-			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
-			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b030
-			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b030
-			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b030
-			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b030
-			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b030
-			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x100b0
-			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b030
-			MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x4001b0a8
-			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
-			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x13030
-			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x13030
-			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
-			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
-			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x13030
-			MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25	0x1b0b0	/* ENET_INT */
-			MX6QDL_PAD_ENET_RX_ER__GPIO1_IO24	0x1b0b0	/* ETHR_nRST */
-		>;
-	};
-
-	pinctrl_reg_audio: audio-reg {
-		fsl,pins = <
-			MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x1b0b0
-		>;
-	};
-
-	pinctrl_pcie: pcie {
-		fsl,pins = <
-			MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
-			MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x1b0b0
-		>;
-	};
-
-	pinctrl_pcie_reg: pciereggrp {
-		fsl,pins = <
-			MX6QDL_PAD_GPIO_2__GPIO1_IO02	0x1b0b0
-			>;
-	};
-
-	pinctrl_pcf8574: pcf8575-pins {
-		fsl,pins = <
-			MX6QDL_PAD_EIM_BCLK__GPIO6_IO31 0x1b0b0
-		>;
-	};
-
-	pinctrl_lcd: lcdgrp {
-		fsl,pins = <
-			MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10	/* R_LCD_DCLK */
-			MX6QDL_PAD_DI0_PIN15__GPIO4_IO17	0x100b0	/* R_LCD_PANEL_PWR */
-			MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02	0x10	/* R_LCD_HSYNC */
-			MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03	0x10	/* R_LCD_VSYNC */
-			MX6QDL_PAD_DI0_PIN4__IPU1_DI0_PIN04	0x10	/* R_LCD_MDISP */
-			MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01	0x10
-			MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02	0x10
-			MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03   0x10
-			MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04   0x10
-			MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05   0x10
-			MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06   0x10
-			MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07   0x10
-			MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08   0x10
-			MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09   0x10
-			MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10  0x10
-			MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11  0x10
-			MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12  0x10
-			MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13  0x10
-			MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14  0x10
-			MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15  0x10
-			MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16  0x10
-		>;
-	};
-
-	pinctrl_pwm3: pwm3grp {
-		fsl,pins = <
-			MX6QDL_PAD_SD4_DAT1__PWM3_OUT		0x1b0b1
-		>;
-	};
-
-	pinctrl_reg_uart3: uart3reg {
-		fsl,pins = <
-			MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28	0x1b0b0
-		>;
-	};
-
-	pinctrl_reg_3v3: reg-3v3 {
-		fsl,pins = <
-			MX6QDL_PAD_ENET_RXD1__GPIO1_IO26	0x1b0b0
-		>;
-	};
-
-	pinctrl_reg_1v8: reg-1v8 {
-		fsl,pins = <
-			MX6QDL_PAD_EIM_D30__GPIO3_IO30		0x1b0b0
-		>;
-	};
-
-	pinctrl_led0: led0 {
-		fsl,pins = <
-			MX6QDL_PAD_ENET_TXD0__GPIO1_IO30	0x1b0b0
-		>;
-	};
 };

arch/arm/dts/imx6-logicpd-som.dtsi

@@ -1,16 +1,6 @@
-/*
- * Copyright 2018 Logic PD
- * This file is adapted from imx6qdl-sabresd.dtsi.
- * Copyright 2012 Freescale Semiconductor, Inc.
- * Copyright 2011 Linaro Ltd.
- *
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 or later at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
- */
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2019 Logic PD, Inc.
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
@@ -20,7 +10,8 @@
 		stdout-path = &uart1;
 	};
 
-	memory {
+	memory@10000000 {
+		device_type = "memory";
 		reg = <0x10000000 0x80000000>;
 	};
 
@@ -35,17 +26,6 @@
 	};
 };
 
-/* Reroute power feeding the CPU to come from the external PMIC */
-&reg_arm
-{
-	vin-supply = <&sw1a_reg>;
-};
-
-&reg_soc
-{
-	vin-supply = <&sw1c_reg>;
-};
-
 &clks {
 	assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
 			  <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
@@ -56,8 +36,8 @@
 &gpmi {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_gpmi_nand>;
-	status = "okay";
 	nand-on-flash-bbt;
+	status = "okay";
 };
 
 &i2c3 {
@@ -66,7 +46,7 @@
 	pinctrl-0 = <&pinctrl_i2c3>;
 	status = "okay";
 
-	pmic: pfuze100@08 {
+	pfuze100: pmic@8 {
 		compatible = "fsl,pfuze100";
 		reg = <0x08>;
 
@@ -94,20 +74,19 @@
 				regulator-max-microvolt = <3300000>;
 				regulator-name = "gen_3v3";
 				regulator-boot-on;
-				/* regulator-always-on; */
 			};
 
 			sw3a_reg: sw3a {
-				regulator-min-microvolt = <400000>;
-				regulator-max-microvolt = <1975000>;
+				regulator-min-microvolt = <1350000>;
+				regulator-max-microvolt = <1350000>;
 				regulator-name = "sw3a_vddr";
 				regulator-boot-on;
 				regulator-always-on;
 			};
 
 			sw3b_reg: sw3b {
-				regulator-min-microvolt = <400000>;
-				regulator-max-microvolt = <1975000>;
+				regulator-min-microvolt = <1350000>;
+				regulator-max-microvolt = <1350000>;
 				regulator-name = "sw3b_vddr";
 				regulator-boot-on;
 				regulator-always-on;
@@ -152,8 +131,8 @@
 
 			vgen3_reg: vgen3 {
 				regulator-name = "gen_vadj_0";
-				regulator-min-microvolt = <3000000>;
-				regulator-max-microvolt = <3000000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
 			};
 
 			vgen4_reg: vgen4 {
@@ -164,8 +143,8 @@
 			};
 
 			vgen5_reg: vgen5 {
-				regulator-name = "gen_adj_1";
-				regulator-min-microvolt = <3300000>;
+				regulator-name = "gen_vadj_1";
+				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <3300000>;
 				regulator-always-on;
 			};
@@ -185,7 +164,15 @@
 		};
 	};
 
-	temp_sense0: tmp102@4a {
+	temperature-sensor@49 {
+		compatible = "ti,tmp102";
+		reg = <0x49>;
+		interrupt-parent = <&gpio6>;
+		interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
+		#thermal-sensor-cells = <1>;
+	};
+
+	temperature-sensor@4a {
 		compatible = "ti,tmp102";
 		reg = <0x4a>;
 		pinctrl-names = "default";
@@ -195,34 +182,57 @@
 		#thermal-sensor-cells = <1>;
 	};
 
-	temp_sense1: tmp102@49 {
-		compatible = "ti,tmp102";
-		reg = <0x49>;
-		interrupt-parent = <&gpio6>;
-		interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
-		#thermal-sensor-cells = <1>;
-	};
-
-	mfg_eeprom: at24@51 {
+	eeprom@51 {
 		compatible = "atmel,24c64";
 		pagesize = <32>;
-		read-only;
+		read-only;	/* Manufacturing EEPROM programmed at factory */
 		reg = <0x51>;
 	};
 
-	user_eeprom: at24@52 {
+	eeprom@52 {
 		compatible = "atmel,24c64";
 		pagesize = <32>;
 		reg = <0x52>;
 	};
 };
 
+/* Reroute power feeding the CPU to come from the external PMIC */
+&reg_arm
+{
+	vin-supply = <&sw1a_reg>;
+};
+
+&reg_soc
+{
+	vin-supply = <&sw1c_reg>;
+};
+
 &iomuxc {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_hog>;
 
-	pinctrl_hog: hoggrp {
+	pinctrl_gpmi_nand: gpmi-nandgrp {
 		fsl,pins = <
+			MX6QDL_PAD_NANDF_CLE__NAND_CLE		0x0b0b1
+			MX6QDL_PAD_NANDF_ALE__NAND_ALE		0x0b0b1
+			MX6QDL_PAD_NANDF_WP_B__NAND_WP_B	0x0b0b1
+			MX6QDL_PAD_NANDF_RB0__NAND_READY_B	0x0b000
+			MX6QDL_PAD_NANDF_CS0__NAND_CE0_B	0x0b0b1
+			MX6QDL_PAD_SD4_CMD__NAND_RE_B		0x0b0b1
+			MX6QDL_PAD_SD4_CLK__NAND_WE_B		0x0b0b1
+			MX6QDL_PAD_NANDF_D0__NAND_DATA00	0x0b0b1
+			MX6QDL_PAD_NANDF_D1__NAND_DATA01	0x0b0b1
+			MX6QDL_PAD_NANDF_D2__NAND_DATA02	0x0b0b1
+			MX6QDL_PAD_NANDF_D3__NAND_DATA03	0x0b0b1
+			MX6QDL_PAD_NANDF_D4__NAND_DATA04	0x0b0b1
+			MX6QDL_PAD_NANDF_D5__NAND_DATA05	0x0b0b1
+			MX6QDL_PAD_NANDF_D6__NAND_DATA06	0x0b0b1
+			MX6QDL_PAD_NANDF_D7__NAND_DATA07	0x0b0b1
+		>;
+	};
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <	/* Enable ARM Debugger */
 			MX6QDL_PAD_CSI0_MCLK__ARM_TRACE_CTL	0x1b0b0
 			MX6QDL_PAD_CSI0_PIXCLK__ARM_EVENTO	0x1b0b0
 			MX6QDL_PAD_CSI0_VSYNC__ARM_TRACE00	0x1b0b0
@@ -246,26 +256,6 @@
 		>;
 	};
 
-	pinctrl_gpmi_nand: gpminandgrp {
-		fsl,pins = <
-			MX6QDL_PAD_NANDF_CLE__NAND_CLE		0x0b0b1
-			MX6QDL_PAD_NANDF_ALE__NAND_ALE		0x0b0b1
-			MX6QDL_PAD_NANDF_WP_B__NAND_WP_B	0x0b0b1
-			MX6QDL_PAD_NANDF_RB0__NAND_READY_B	0x0b000
-			MX6QDL_PAD_NANDF_CS0__NAND_CE0_B	0x0b0b1
-			MX6QDL_PAD_SD4_CMD__NAND_RE_B		0x0b0b1
-			MX6QDL_PAD_SD4_CLK__NAND_WE_B		0x0b0b1
-			MX6QDL_PAD_NANDF_D0__NAND_DATA00	0x0b0b1
-			MX6QDL_PAD_NANDF_D1__NAND_DATA01	0x0b0b1
-			MX6QDL_PAD_NANDF_D2__NAND_DATA02	0x0b0b1
-			MX6QDL_PAD_NANDF_D3__NAND_DATA03	0x0b0b1
-			MX6QDL_PAD_NANDF_D4__NAND_DATA04	0x0b0b1
-			MX6QDL_PAD_NANDF_D5__NAND_DATA05	0x0b0b1
-			MX6QDL_PAD_NANDF_D6__NAND_DATA06	0x0b0b1
-			MX6QDL_PAD_NANDF_D7__NAND_DATA07	0x0b0b1
-		>;
-	};
-
 	pinctrl_i2c3: i2c3grp {
 		fsl,pins = <
 			MX6QDL_PAD_EIM_D17__I2C3_SCL		0x4001b8b1
@@ -273,6 +263,12 @@
 		>;
 	};
 
+	pinctrl_tempsense: tempsensegrp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x1b0b0
+		>;
+	};
+
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA	0x1b0b1
@@ -282,7 +278,7 @@
 
 	pinctrl_uart2: uart2grp {
 		fsl,pins = <
-			MX6QDL_PAD_SD3_RST__GPIO7_IO08	0x13059	/* BT_EN */
+			MX6QDL_PAD_SD3_RST__GPIO7_IO08		0x13059	/* BT_EN */
 			MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA	0x1b0b1
 			MX6QDL_PAD_SD4_DAT5__UART2_RTS_B	0x1b0b1
 			MX6QDL_PAD_SD4_DAT6__UART2_CTS_B	0x1b0b1
@@ -313,12 +309,6 @@
 			MX6QDL_PAD_SD3_DAT5__GPIO7_IO00	0x17059 /* WLAN_EN */
 		>;
 	};
-
-	pinctrl_tempsense: tempsensegrp {
-		fsl,pins = <
-			MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x1b0b0	/* Temp Sense Alert */
-		>;
-	};
 };
 
 &snvs_poweroff {
@@ -334,8 +324,9 @@
 &uart2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart2>;
-	status = "okay";
 	uart-has-rtscts;
+	status = "okay";
+
 	bluetooth {
 		compatible = "ti,wl1837-st";
 		enable-gpios = <&gpio7 8 GPIO_ACTIVE_HIGH>;
@@ -347,9 +338,9 @@
 	pinctrl-0 = <&pinctrl_usdhc1>;
 	non-removable;
 	keep-power-in-suspend;
-	enable-sdio-wakeup;
-	status = "okay";
+	wakeup-source;
 	vmmc-supply = <&sw2_reg>;
+	status = "okay";
 };
 
 &usdhc3 {
@@ -360,9 +351,10 @@
 	keep-power-in-suspend;
 	wakeup-source;
 	vmmc-supply = <&reg_wl18xx_vmmc>;
-	status = "okay";
 	#address-cells = <1>;
 	#size-cells = <0>;
+	status = "okay";
+
 	wlcore: wlcore@2 {
 		  compatible = "ti,wl1837";
 		  reg = <2>;

arch/arm/dts/imx6dl-wandboard-revb1.dts

@@ -13,6 +13,7 @@
 	compatible = "wand,imx6dl-wandboard", "fsl,imx6dl";
 
 	memory@10000000 {
+		device_type = "memory";
 		reg = <0x10000000 0x40000000>;
 	};
 };

arch/arm/dts/imx6q-dhcom-pdk2.dts

@@ -0,0 +1,151 @@
+// SPDX-License-Identifier: (GPL-2.0+)
+/*
+ * Copyright (C) 2015 DH electronics GmbH
+ * Copyright (C) 2018 Marek Vasut <marex@denx.de>
+ */
+
+/dts-v1/;
+
+#include "imx6q-dhcom-som.dtsi"
+
+/ {
+	model = "Freescale i.MX6 Quad DHCOM Premium Developer Kit (2)";
+	compatible = "dh,imx6q-dhcom-pdk2", "dh,imx6q-dhcom-som", "fsl,imx6q";
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	clk_ext_audio_codec: clock-codec {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24000000>;
+	};
+
+	sound {
+		compatible = "fsl,imx-audio-sgtl5000";
+		model = "imx-sgtl5000";
+		ssi-controller = <&ssi1>;
+		audio-codec = <&sgtl5000>;
+		audio-routing =
+			"MIC_IN", "Mic Jack",
+			"Mic Jack", "Mic Bias",
+			"LINE_IN", "Line In Jack",
+			"Headphone Jack", "HP_OUT";
+		mux-int-port = <1>;
+		mux-ext-port = <3>;
+	};
+};
+
+&audmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_audmux_ext>;
+	status = "okay";
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c2>;
+	status = "okay";
+};
+
+&i2c2 {
+	sgtl5000: codec@a {
+		compatible = "fsl,sgtl5000";
+		reg = <0x0a>;
+		#sound-dai-cells = <0>;
+		clocks = <&clk_ext_audio_codec>;
+		VDDA-supply = <&reg_3p3v>;
+		VDDIO-supply = <&reg_3p3v>;
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog_base &pinctrl_hog>;
+
+	pinctrl_hog: hog-grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x400120b0
+			MX6QDL_PAD_GPIO_4__GPIO1_IO04		0x400120b0
+			MX6QDL_PAD_GPIO_5__GPIO1_IO05		0x400120b0
+			MX6QDL_PAD_CSI0_DAT17__GPIO6_IO03	0x400120b0
+			MX6QDL_PAD_GPIO_19__GPIO4_IO05		0x120b0
+			MX6QDL_PAD_DI0_PIN4__GPIO4_IO20		0x400120b0
+			MX6QDL_PAD_EIM_D27__GPIO3_IO27		0x120b0
+			MX6QDL_PAD_KEY_ROW0__GPIO4_IO07		0x120b0
+			MX6QDL_PAD_KEY_COL1__GPIO4_IO08		0x400120b0
+			MX6QDL_PAD_NANDF_CS1__GPIO6_IO14	0x400120b0
+			MX6QDL_PAD_NANDF_CS2__GPIO6_IO15	0x400120b0
+			MX6QDL_PAD_KEY_ROW1__GPIO4_IO09		0x400120b0
+			MX6QDL_PAD_SD3_DAT5__GPIO7_IO00		0x400120b0
+			MX6QDL_PAD_SD3_DAT4__GPIO7_IO01		0x400120b0
+			MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21	0x400120b0
+			MX6QDL_PAD_GPIO_18__GPIO7_IO13		0x400120b0
+			MX6QDL_PAD_SD1_CMD__GPIO1_IO18		0x400120b0
+			MX6QDL_PAD_SD1_DAT0__GPIO1_IO16		0x400120b0
+			MX6QDL_PAD_SD1_DAT1__GPIO1_IO17		0x400120b0
+			MX6QDL_PAD_SD1_DAT2__GPIO1_IO19		0x400120b0
+			MX6QDL_PAD_SD1_CLK__GPIO1_IO20		0x400120b0
+			MX6QDL_PAD_CSI0_PIXCLK__GPIO5_IO18	0x400120b0
+			MX6QDL_PAD_CSI0_MCLK__GPIO5_IO19	0x400120b0
+			MX6QDL_PAD_KEY_COL0__GPIO4_IO06		0x400120b0
+		>;
+	};
+
+	pinctrl_audmux_ext: audmux-ext-grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT7__AUD3_RXD		0x130b0
+			MX6QDL_PAD_CSI0_DAT4__AUD3_TXC		0x130b0
+			MX6QDL_PAD_CSI0_DAT5__AUD3_TXD		0x110b0
+			MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS		0x130b0
+		>;
+	};
+
+	pinctrl_enet_1G: enet-1G-grp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x100b0
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x100b0
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x100b0
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x100b0
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x100b0
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x100b0
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x100b0
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x100b0
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x100b0
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b0b0
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b0b0
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b0b0
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b0b0
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b0b0
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b0b0
+			MX6QDL_PAD_EIM_D29__GPIO3_IO29		0x000b0
+			MX6QDL_PAD_GPIO_0__GPIO1_IO00		0x000b1
+			MX6QDL_PAD_EIM_D26__GPIO3_IO26		0x000b1
+		>;
+	};
+
+	pinctrl_pcie: pcie-grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20	0x1b0b1
+		>;
+	};
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie>;
+	reset-gpio = <&gpio6 14 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&ssi1 {
+	status = "okay";
+};
+
+&sata {
+	status = "okay";
+};
+
+&usdhc3 {
+	status = "okay";
+};

arch/arm/dts/imx6q-dhcom-som.dtsi

@@ -0,0 +1,477 @@
+// SPDX-License-Identifier: (GPL-2.0+)
+/*
+ * Copyright (C) 2015 DH electronics GmbH
+ * Copyright (C) 2018 Marek Vasut <marex@denx.de>
+ */
+
+#include "imx6q.dtsi"
+#include <dt-bindings/pwm/pwm.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/imx6qdl-clock.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	aliases {
+		mmc0 = &usdhc2;
+		mmc1 = &usdhc3;
+		mmc2 = &usdhc4;
+		mmc3 = &usdhc1;
+	};
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0x40000000>;
+	};
+
+	reg_usb_otg_vbus: regulator-usb-otg-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_usb_h1_vbus: regulator-usb-h1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_h1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_3p3v: regulator-3P3V {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan1>;
+	status = "okay";
+};
+
+&can2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan2>;
+	status = "okay";
+};
+
+&ecspi1 {
+	cs-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>, <&gpio4 11 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	status = "okay";
+
+	flash@0 {	/* S25FL116K */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		spi-max-frequency = <50000000>;
+		reg = <0>;
+		m25p,fast-read;
+	};
+};
+
+&ecspi2 {
+	cs-gpios = <&gpio5 29 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	status = "okay";
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet_100M>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy0>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@0 {	/* SMSC LAN8710Ai */
+			reg = <0>;
+			max-speed = <100>;
+			reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
+			reset-delay-us = <1000>;
+			reset-post-delay-us = <1000>;
+		};
+	};
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	ltc3676: pmic@3c {
+		compatible = "lltc,ltc3676";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pmic_hw300>;
+		reg = <0x3c>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+
+		regulators {
+			sw1_reg: sw1 {
+				regulator-min-microvolt = <787500>;
+				regulator-max-microvolt = <1527272>;
+				lltc,fb-voltage-divider = <100000 110000>;
+				regulator-suspend-mem-microvolt = <1040000>;
+				regulator-ramp-delay = <7000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw2_reg: sw2 {
+				regulator-min-microvolt = <1885714>;
+				regulator-max-microvolt = <3657142>;
+				lltc,fb-voltage-divider = <100000 28000>;
+				regulator-ramp-delay = <7000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3_reg: sw3 {
+				regulator-min-microvolt = <787500>;
+				regulator-max-microvolt = <1527272>;
+				lltc,fb-voltage-divider = <100000 110000>;
+				regulator-suspend-mem-microvolt = <980000>;
+				regulator-ramp-delay = <7000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw4_reg: sw4 {
+				regulator-min-microvolt = <855571>;
+				regulator-max-microvolt = <1659291>;
+				lltc,fb-voltage-divider = <100000 93100>;
+				regulator-ramp-delay = <7000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo1_reg: ldo1 {
+				regulator-min-microvolt = <3240306>;
+				regulator-max-microvolt = <3240306>;
+				lltc,fb-voltage-divider = <102000 29400>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo2_reg: ldo2 {
+				regulator-min-microvolt = <2484708>;
+				regulator-max-microvolt = <2484708>;
+				lltc,fb-voltage-divider = <100000 41200>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+
+	touchscreen@49 {	/* TSC2004 */
+		compatible = "ti,tsc2004";
+		reg = <0x49>;
+		vio-supply = <&reg_3p3v>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_tsc2004_hw300>;
+		interrupts-extended = <&gpio4 14 IRQ_TYPE_EDGE_FALLING>;
+		status = "disabled";
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+
+	rtc@56 {
+		compatible = "rv3029c2";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_rtc_hw300>;
+		reg = <0x56>;
+		interrupt-parent = <&gpio7>;
+		interrupts = <12 2>;
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog_base>;
+
+	pinctrl_hog_base: hog-base-grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_A19__GPIO2_IO19		0x120b0
+			MX6QDL_PAD_EIM_A23__GPIO6_IO06		0x120b0
+			MX6QDL_PAD_EIM_A22__GPIO2_IO16		0x120b0
+			MX6QDL_PAD_EIM_A16__GPIO2_IO22		0x120b0
+			MX6QDL_PAD_EIM_A17__GPIO2_IO21		0x120b0
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1-grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D17__ECSPI1_MISO		0x100b1
+			MX6QDL_PAD_EIM_D18__ECSPI1_MOSI		0x100b1
+			MX6QDL_PAD_EIM_D16__ECSPI1_SCLK		0x100b1
+			MX6QDL_PAD_EIM_EB2__GPIO2_IO30		0x1b0b0
+			MX6QDL_PAD_KEY_ROW2__GPIO4_IO11		0x1b0b0
+		>;
+	};
+
+	pinctrl_ecspi2: ecspi2-grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT10__ECSPI2_MISO	0x100b1
+			MX6QDL_PAD_CSI0_DAT9__ECSPI2_MOSI	0x100b1
+			MX6QDL_PAD_CSI0_DAT8__ECSPI2_SCLK	0x100b1
+			MX6QDL_PAD_CSI0_DAT11__GPIO5_IO29	0x1b0b0
+		>;
+	};
+
+	pinctrl_enet_100M: enet-100M-grp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+			MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN	0x1b0b0
+			MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER	0x1b0b0
+			MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0	0x1b0b0
+			MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1	0x1b0b0
+			MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN	0x1b0b0
+			MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0	0x1b0b0
+			MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1	0x1b0b0
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x4001b0a8
+			MX6QDL_PAD_EIM_WAIT__GPIO5_IO00		0x000b0
+			MX6QDL_PAD_KEY_ROW4__GPIO4_IO15		0x000b1
+			MX6QDL_PAD_GPIO_7__GPIO1_IO07		0x120b0
+		>;
+	};
+
+	pinctrl_flexcan1: flexcan1-grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX	0x1b0b0
+			MX6QDL_PAD_GPIO_8__FLEXCAN1_RX		0x1b0b0
+		>;
+	};
+
+	pinctrl_flexcan2: flexcan2-grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_DAT0__FLEXCAN2_TX	0x1b0b0
+			MX6QDL_PAD_SD3_DAT1__FLEXCAN2_RX	0x1b0b0
+		>;
+	};
+
+	pinctrl_i2c1: i2c1-grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__I2C1_SCL		0x4001b8b1
+			MX6QDL_PAD_EIM_D28__I2C1_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c2: i2c2-grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001b8b1
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3-grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_3__I2C3_SCL		0x4001b8b1
+			MX6QDL_PAD_GPIO_6__I2C3_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_pmic_hw300: pmic-hw300-grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_A25__GPIO5_IO02		0x1B0B0
+		>;
+	};
+
+	pinctrl_rtc_hw300: rtc-hw300-grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_17__GPIO7_IO12		0x120B0
+		>;
+	};
+
+	pinctrl_tsc2004_hw300: tsc2004-hw300-grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL4__GPIO4_IO14		0x120B0
+		>;
+	};
+
+	pinctrl_uart1: uart1-grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA	0x1b0b1
+			MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA	0x1b0b1
+			MX6QDL_PAD_EIM_D20__UART1_RTS_B		0x1b0b1
+			MX6QDL_PAD_EIM_D19__UART1_CTS_B		0x4001b0b1
+			MX6QDL_PAD_EIM_D23__GPIO3_IO23		0x4001b0b1
+			MX6QDL_PAD_EIM_D24__GPIO3_IO24		0x4001b0b1
+			MX6QDL_PAD_EIM_D25__GPIO3_IO25		0x4001b0b1
+			MX6QDL_PAD_EIM_EB3__GPIO2_IO31		0x4001b0b1
+		>;
+	};
+
+	pinctrl_uart4: uart4-grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT12__UART4_TX_DATA	0x1b0b1
+			MX6QDL_PAD_CSI0_DAT13__UART4_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart5: uart5-grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT14__UART5_TX_DATA	0x1b0b1
+			MX6QDL_PAD_CSI0_DAT15__UART5_RX_DATA	0x1b0b1
+			MX6QDL_PAD_CSI0_DAT18__UART5_RTS_B	0x1b0b1
+			MX6QDL_PAD_CSI0_DAT19__UART5_CTS_B	0x4001b0b1
+		>;
+	};
+
+	pinctrl_usbh1: usbh1-grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D31__GPIO3_IO31		0x120B0
+		>;
+	};
+
+	pinctrl_usbotg: usbotg-grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_1__USB_OTG_ID		0x17059
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2-grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD2_CMD__SD2_CMD		0x17059
+			MX6QDL_PAD_SD2_CLK__SD2_CLK		0x10059
+			MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x17059
+			MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x17059
+			MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x17059
+			MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x17059
+			MX6QDL_PAD_NANDF_CS3__GPIO6_IO16	0x120B0
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3-grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
+			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
+			MX6QDL_PAD_SD3_RST__GPIO7_IO08		0x120B0
+		>;
+	};
+
+	pinctrl_usdhc4: usdhc4-grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_CMD__SD4_CMD		0x17059
+			MX6QDL_PAD_SD4_CLK__SD4_CLK		0x10059
+			MX6QDL_PAD_SD4_DAT0__SD4_DATA0		0x17059
+			MX6QDL_PAD_SD4_DAT1__SD4_DATA1		0x17059
+			MX6QDL_PAD_SD4_DAT2__SD4_DATA2		0x17059
+			MX6QDL_PAD_SD4_DAT3__SD4_DATA3		0x17059
+			MX6QDL_PAD_SD4_DAT4__SD4_DATA4		0x17059
+			MX6QDL_PAD_SD4_DAT5__SD4_DATA5		0x17059
+			MX6QDL_PAD_SD4_DAT6__SD4_DATA6		0x17059
+			MX6QDL_PAD_SD4_DAT7__SD4_DATA7		0x17059
+		>;
+	};
+};
+
+&reg_arm {
+	vin-supply = <&sw3_reg>;
+};
+
+&reg_soc {
+	vin-supply = <&sw1_reg>;
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	uart-has-rtscts;
+	dtr-gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
+	dsr-gpios = <&gpio3 25 GPIO_ACTIVE_LOW>;
+	dcd-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
+	rng-gpios = <&gpio2 31 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+&uart5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart5>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&usbh1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbh1>;
+	vbus-supply = <&reg_usb_h1_vbus>;
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usbotg {
+	vbus-supply = <&reg_usb_otg_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	disable-over-current;
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	cd-gpios = <&gpio6 16 GPIO_ACTIVE_HIGH>;
+	keep-power-in-suspend;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	cd-gpios = <&gpio7 8 GPIO_ACTIVE_LOW>;
+	fsl,wp-controller;
+	keep-power-in-suspend;
+	status = "disabled";
+};
+
+&usdhc4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc4>;
+	non-removable;
+	bus-width = <8>;
+	no-1-8-v;
+	keep-power-in-suspend;
+	status = "okay";
+};

arch/arm/dts/imx6q-logicpd.dts

@@ -1,45 +1,6 @@
-/*
- * Copyright 2018 Logic PD, Inc.
- * Based on SabreSD, Copyright 2016 Freescale Semiconductor, Inc.
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of the
- *     License, or (at your option) any later version.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2019 Logic PD, Inc.
 
 /dts-v1/;
 #include "imx6q.dtsi"
@@ -47,10 +8,10 @@
 #include "imx6-logicpd-baseboard.dtsi"
 
 / {
-	model = "Logic PD i.MX6QD SOM-M3 (HDMI)";
+	model = "Logic PD i.MX6QD SOM-M3";
 	compatible = "fsl,imx6q";
 
-	backlight: backlight_lvds {
+	backlight: backlight-lvds {
 		compatible = "pwm-backlight";
 		pwms = <&pwm3 0 20000>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
@@ -58,6 +19,16 @@
 		power-supply = <&reg_lcd>;
 	};
 
+	panel-lvds0 {
+		compatible = "okaya,rs800480t-7x0gp";
+
+		port {
+			panel_in_lvds0: endpoint {
+				remote-endpoint = <&lvds0_out>;
+			};
+		};
+	};
+
 	reg_lcd: regulator-lcd {
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_lcd_reg>;
@@ -72,7 +43,7 @@
 		startup-delay-us = <500000>;
 	};
 
-	lcd_reset: lcd_reset {
+	reg_lcd_reset: regulator-lcd-reset {
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_lcd_reset>;
 		compatible = "regulator-fixed";
@@ -84,57 +55,6 @@
 		regulator-always-on;
 		vin-supply = <&reg_lcd>;
 	};
-
-	panel-lvds0 {
-		compatible = "ampire,am800480b3tmqw";
-		backlight = <&backlight>;
-
-		port {
-			panel_in_lvds0: endpoint {
-				remote-endpoint = <&lvds0_out>;
-			};
-		};
-	};
-};
-
-&hdmi {
-	ddc-i2c-bus = <&i2c3>;
-	status = "okay";
-};
-
-&i2c1 {
-	ili_touch: ilitouch@26 {
-		compatible = "ili,ili2117a";
-		reg = <0x26>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_touchscreen>;
-		interrupts-extended = <&gpio1 6 IRQ_TYPE_EDGE_RISING>;
-		ili2117a,poll-period = <10>;
-		ili2117a,max-touch = <2>;
-	};
-};
-
-&reg_hdmi {
-	regulator-always-on;
-};
-
-&ldb {
-	status = "okay";
-
-	lvds-channel@0 {
-		fsl,data-mapping = "spwg";
-		fsl,data-width = <24>;
-		status = "okay";
-
-		port@4 {
-			reg = <4>;
-
-			lvds0_out: endpoint {
-				remote-endpoint = <&panel_in_lvds0>;
-			};
-		};
-	};
-
 };
 
 &clks {
@@ -148,12 +68,35 @@
 				 <&clks IMX6QDL_CLK_PLL2_PFD2_396M>;
 };
 
+&hdmi {
+	ddc-i2c-bus = <&i2c3>;
+	status = "okay";
+};
+
+&ldb {
+	status = "okay";
+
+	lvds-channel@0 {
+		fsl,data-mapping = "spwg";
+		fsl,data-width = <24>;
+		status = "okay";
+
+		port@4 {
+			reg = <4>;
+			lvds0_out: endpoint {
+				remote-endpoint = <&panel_in_lvds0>;
+			};
+		};
+	};
+
+};
+
 &pwm3 {
 	status = "okay";
 };
 
-&usdhc2 {
-	cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+&reg_hdmi {
+	regulator-always-on;	/* Without this, the level shifter on HDMI doesn't turn on */
 };
 
 &iomuxc {
@@ -165,7 +108,7 @@
 
 	pinctrl_lcd_reset: lcdreset {
 		fsl,pins = <
-			MX6QDL_PAD_EIM_A25__GPIO5_IO02      0x100b0	/* LCD_nRESET */
+			MX6QDL_PAD_EIM_A25__GPIO5_IO02	0x100b0	/* LCD_nRESET */
 		>;
 	};
 
@@ -175,4 +118,3 @@
 		>;
 	};
 };
-

arch/arm/dts/imx6q-novena.dts

@@ -0,0 +1,797 @@
+/*
+ * Copyright 2015 Sutajio Ko-Usagi PTE LTD
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of
+ *     the License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ *     You should have received a copy of the GNU General Public
+ *     License along with this file; if not, write to the Free
+ *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ *     MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ *
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Kosagi Novena Dual/Quad";
+	compatible = "kosagi,imx6q-novena", "fsl,imx6q";
+
+	/* Will be filled by the bootloader */
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0>;
+	};
+
+	aliases {
+		mmc0 = &usdhc3;
+		mmc1 = &usdhc2;
+	};
+
+	chosen {
+		stdout-path = &uart2;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm1 0 10000000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_backlight_novena>;
+		power-supply = <&reg_lvds_lcd>;
+		brightness-levels = <0 3 6 12 16 24 32 48 64 96 128 192 255>;
+		default-brightness-level = <12>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys_novena>;
+
+		user-button {
+			label = "User Button";
+			gpios = <&gpio4 14 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+		};
+
+		lid {
+			label = "Lid";
+			gpios = <&gpio4 12 GPIO_ACTIVE_LOW>;
+			linux,input-type = <5>;	/* EV_SW */
+			linux,code = <0>;	/* SW_LID */
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_leds_novena>;
+
+		heartbeat {
+			label = "novena:white:panel";
+			gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+	};
+
+	panel: panel {
+		compatible = "innolux,n133hse-ea1", "simple-panel";
+		backlight = <&backlight>;
+	};
+
+	reg_2p5v: regulator-2p5v {
+		compatible = "regulator-fixed";
+		regulator-name = "2P5V";
+		regulator-min-microvolt = <2500000>;
+		regulator-max-microvolt = <2500000>;
+		regulator-always-on;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_audio_codec: regulator-audio-codec {
+		compatible = "regulator-fixed";
+		regulator-name = "es8328-power";
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		startup-delay-us = <400000>;
+		gpio = <&gpio5 17 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_display: regulator-display {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd-display-power";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <200000>;
+		gpio = <&gpio5 28 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_lvds_lcd: regulator-lvds-lcd {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd-lvds-power";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_pcie: regulator-pcie {
+		compatible = "regulator-fixed";
+		regulator-name = "pcie-bus-power";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+		gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_sata: regulator-sata {
+		compatible = "regulator-fixed";
+		regulator-name = "sata-power";
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <10000>;
+		gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_usb_otg_vbus: regulator-usb-otg-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+	};
+
+	sound {
+		compatible = "fsl,imx-audio-es8328";
+		model = "imx-audio-es8328";
+		ssi-controller = <&ssi1>;
+		audio-codec = <&codec>;
+		audio-amp-supply = <&reg_audio_codec>;
+		jack-gpio = <&gpio5 15 GPIO_ACTIVE_HIGH>;
+		audio-routing =
+			"Speaker", "LOUT2",
+			"Speaker", "ROUT2",
+			"Speaker", "audio-amp",
+			"Headphone", "ROUT1",
+			"Headphone", "LOUT1",
+			"LINPUT1", "Mic Jack",
+			"RINPUT1", "Mic Jack",
+			"Mic Jack", "Mic Bias";
+		mux-int-port = <0x1>;
+		mux-ext-port = <0x3>;
+	};
+};
+
+&audmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_audmux_novena>;
+	status = "okay";
+};
+
+&ecspi3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi3_novena>;
+	status = "okay";
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet_novena>;
+	phy-mode = "rgmii";
+	phy-reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
+	rxc-skew-ps = <3000>;
+	rxdv-skew-ps = <0>;
+	txc-skew-ps = <3000>;
+	txen-skew-ps = <0>;
+	rxd0-skew-ps = <0>;
+	rxd1-skew-ps = <0>;
+	rxd2-skew-ps = <0>;
+	rxd3-skew-ps = <0>;
+	txd0-skew-ps = <3000>;
+	txd1-skew-ps = <3000>;
+	txd2-skew-ps = <3000>;
+	txd3-skew-ps = <3000>;
+	status = "okay";
+};
+
+&hdmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hdmi_novena>;
+	ddc-i2c-bus = <&i2c2>;
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1_novena>;
+	status = "okay";
+
+	accel: mma8452@1c {
+		compatible = "fsl,mma8452";
+		reg = <0x1c>;
+	};
+
+	rtc: pcf8523@68 {
+		compatible = "nxp,pcf8523";
+		reg = <0x68>;
+	};
+
+	sbs_battery: bq20z75@b {
+		compatible = "sbs,sbs-battery";
+		reg = <0x0b>;
+		sbs,i2c-retry-count = <50>;
+	};
+
+	touch: stmpe811@44 {
+		compatible = "st,stmpe811";
+		reg = <0x44>;
+		irq-gpio = <&gpio5 13 GPIO_ACTIVE_HIGH>;
+		id = <0>;
+		blocks = <0x5>;
+		irq-trigger = <0x1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_stmpe_novena>;
+		vio-supply = <&reg_3p3v>;
+		vcc-supply = <&reg_3p3v>;
+
+		stmpe_touchscreen {
+			compatible = "st,stmpe-ts";
+			st,sample-time = <4>;
+			st,mod-12b = <1>;
+			st,ref-sel = <0>;
+			st,adc-freq = <1>;
+			st,ave-ctrl = <1>;
+			st,touch-det-delay = <2>;
+			st,settling = <2>;
+			st,fraction-z = <7>;
+			st,i-drive = <1>;
+		};
+	};
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2_novena>;
+	status = "okay";
+
+	pmic: pfuze100@8 {
+		compatible = "fsl,pfuze100";
+		reg = <0x08>;
+
+		regulators {
+			reg_sw1a: sw1a {
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1875000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			reg_sw1c: sw1c {
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1875000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_sw2: sw2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_sw3a: sw3a {
+				regulator-min-microvolt = <400000>;
+				regulator-max-microvolt = <1975000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_sw3b: sw3b {
+				regulator-min-microvolt = <400000>;
+				regulator-max-microvolt = <1975000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_sw4: sw4 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			reg_swbst: swbst {
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5150000>;
+				regulator-boot-on;
+			};
+
+			reg_snvs: vsnvs {
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_vref: vrefddr {
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_vgen1: vgen1 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+			};
+
+			reg_vgen2: vgen2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+			};
+
+			reg_vgen3: vgen3 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			reg_vgen4: vgen4 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			reg_vgen5: vgen5 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			reg_vgen6: vgen6 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3_novena>;
+	status = "okay";
+
+	codec: es8328@11 {
+		compatible = "everest,es8328";
+		reg = <0x11>;
+		DVDD-supply = <&reg_audio_codec>;
+		AVDD-supply = <&reg_audio_codec>;
+		PVDD-supply = <&reg_audio_codec>;
+		HPVDD-supply = <&reg_audio_codec>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_sound_novena>;
+		clocks = <&clks IMX6QDL_CLK_CKO1>;
+		assigned-clocks = <&clks IMX6QDL_CLK_CKO>,
+				  <&clks IMX6QDL_CLK_CKO1_SEL>,
+				  <&clks IMX6QDL_CLK_PLL4_AUDIO>,
+				  <&clks IMX6QDL_CLK_CKO1>;
+		assigned-clock-parents = <&clks IMX6QDL_CLK_CKO1>,
+					 <&clks IMX6QDL_CLK_PLL4_AUDIO_DIV>,
+					 <&clks IMX6QDL_CLK_OSC>,
+					 <&clks IMX6QDL_CLK_CKO1_PODF>;
+		assigned-clock-rates = <0 0 722534400 22579200>;
+	};
+};
+
+&kpp {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_kpp_novena>;
+	linux,keymap = <
+		MATRIX_KEY(1, 1, KEY_CONFIG)
+	>;
+	status = "okay";
+};
+
+&ldb {
+	fsl,dual-channel;
+	status = "okay";
+
+	lvds-channel@0 {
+		fsl,data-mapping = "jeida";
+		fsl,data-width = <24>;
+		fsl,panel = <&panel>;
+		status = "okay";
+	};
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie_novena>;
+	reset-gpio = <&gpio3 29 GPIO_ACTIVE_LOW>;
+	vpcie-supply = <&reg_pcie>;
+	status = "okay";
+};
+
+&pwm1 {
+	status = "okay";
+};
+
+&sata {
+	target-supply = <&reg_sata>;
+	fsl,transmit-level-mV = <1025>;
+	fsl,transmit-boost-mdB = <0>;
+	fsl,transmit-atten-16ths = <8>;
+	status = "okay";
+};
+
+&ssi1 {
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2_novena>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3_novena>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4_novena>;
+	status = "okay";
+};
+
+&usbotg {
+	vbus-supply = <&reg_usb_otg_vbus>;
+	dr_mode = "otg";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg_novena>;
+	disable-over-current;
+	status = "okay";
+};
+
+&usbh1 {
+	vbus-supply = <&reg_swbst>;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2_novena>;
+	cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3_novena>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_audmux_novena: audmuxgrp-novena {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT7__AUD3_RXD		0x130b0
+			MX6QDL_PAD_CSI0_DAT4__AUD3_TXC		0x130b0
+			MX6QDL_PAD_CSI0_DAT5__AUD3_TXD		0x110b0
+			MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS		0x130b0
+		>;
+	};
+
+	pinctrl_backlight_novena: backlightgrp-novena {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT8__PWM1_OUT		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT10__GPIO5_IO28	0x1b0b1
+			MX6QDL_PAD_KEY_ROW4__GPIO4_IO15		0x1b0b1
+		>;
+	};
+
+	pinctrl_ecspi3_novena: ecspi3grp-novena {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO	0x100b1
+			MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI	0x100b1
+			MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK	0x100b1
+		>;
+	};
+
+	pinctrl_enet_novena: enetgrp-novena {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b020
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b028
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b028
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b028
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b028
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b028
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b0b0
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b030
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b030
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x4001b0a8
+			/* Ethernet reset */
+			MX6QDL_PAD_EIM_D23__GPIO3_IO23		0x1b0b1
+		>;
+	};
+
+	pinctrl_fpga_gpio: fpgagpiogrp-novena {
+		fsl,pins = <
+			/* FPGA power */
+			MX6QDL_PAD_SD1_DAT1__GPIO1_IO17		0x1b0b1
+			/* Reset */
+			MX6QDL_PAD_DISP0_DAT13__GPIO5_IO07	0x1b0b1
+			/* FPGA GPIOs */
+			MX6QDL_PAD_EIM_DA0__GPIO3_IO00		0x1b0b1
+			MX6QDL_PAD_EIM_DA1__GPIO3_IO01		0x1b0b1
+			MX6QDL_PAD_EIM_DA2__GPIO3_IO02		0x1b0b1
+			MX6QDL_PAD_EIM_DA3__GPIO3_IO03		0x1b0b1
+			MX6QDL_PAD_EIM_DA4__GPIO3_IO04		0x1b0b1
+			MX6QDL_PAD_EIM_DA5__GPIO3_IO05		0x1b0b1
+			MX6QDL_PAD_EIM_DA6__GPIO3_IO06		0x1b0b1
+			MX6QDL_PAD_EIM_DA7__GPIO3_IO07		0x1b0b1
+			MX6QDL_PAD_EIM_DA8__GPIO3_IO08		0x1b0b1
+			MX6QDL_PAD_EIM_DA9__GPIO3_IO09		0x1b0b1
+			MX6QDL_PAD_EIM_DA10__GPIO3_IO10		0x1b0b1
+			MX6QDL_PAD_EIM_DA11__GPIO3_IO11		0x1b0b1
+			MX6QDL_PAD_EIM_DA12__GPIO3_IO12		0x1b0b1
+			MX6QDL_PAD_EIM_DA13__GPIO3_IO13		0x1b0b1
+			MX6QDL_PAD_EIM_DA14__GPIO3_IO14		0x1b0b1
+			MX6QDL_PAD_EIM_DA15__GPIO3_IO15		0x1b0b1
+			MX6QDL_PAD_EIM_A16__GPIO2_IO22		0x1b0b1
+			MX6QDL_PAD_EIM_A17__GPIO2_IO21		0x1b0b1
+			MX6QDL_PAD_EIM_A18__GPIO2_IO20		0x1b0b1
+			MX6QDL_PAD_EIM_CS0__GPIO2_IO23		0x1b0b1
+			MX6QDL_PAD_EIM_CS1__GPIO2_IO24		0x1b0b1
+			MX6QDL_PAD_EIM_LBA__GPIO2_IO27		0x1b0b1
+			MX6QDL_PAD_EIM_OE__GPIO2_IO25		0x1b0b1
+			MX6QDL_PAD_EIM_RW__GPIO2_IO26		0x1b0b1
+			MX6QDL_PAD_EIM_WAIT__GPIO5_IO00		0x1b0b1
+			MX6QDL_PAD_EIM_BCLK__GPIO6_IO31		0x1b0b1
+		>;
+	};
+
+	pinctrl_fpga_eim: fpgaeimgrp-novena {
+		fsl,pins = <
+			/* FPGA power */
+			MX6QDL_PAD_SD1_DAT1__GPIO1_IO17		0x1b0b1
+			/* Reset */
+			MX6QDL_PAD_DISP0_DAT13__GPIO5_IO07	0x1b0b1
+			/* FPGA GPIOs */
+			MX6QDL_PAD_EIM_DA0__EIM_AD00		0xb0f1
+			MX6QDL_PAD_EIM_DA1__EIM_AD01		0xb0f1
+			MX6QDL_PAD_EIM_DA2__EIM_AD02		0xb0f1
+			MX6QDL_PAD_EIM_DA3__EIM_AD03		0xb0f1
+			MX6QDL_PAD_EIM_DA4__EIM_AD04		0xb0f1
+			MX6QDL_PAD_EIM_DA5__EIM_AD05		0xb0f1
+			MX6QDL_PAD_EIM_DA6__EIM_AD06		0xb0f1
+			MX6QDL_PAD_EIM_DA7__EIM_AD07		0xb0f1
+			MX6QDL_PAD_EIM_DA8__EIM_AD08		0xb0f1
+			MX6QDL_PAD_EIM_DA9__EIM_AD09		0xb0f1
+			MX6QDL_PAD_EIM_DA10__EIM_AD10		0xb0f1
+			MX6QDL_PAD_EIM_DA11__EIM_AD11		0xb0f1
+			MX6QDL_PAD_EIM_DA12__EIM_AD12		0xb0f1
+			MX6QDL_PAD_EIM_DA13__EIM_AD13		0xb0f1
+			MX6QDL_PAD_EIM_DA14__EIM_AD14		0xb0f1
+			MX6QDL_PAD_EIM_DA15__EIM_AD15		0xb0f1
+			MX6QDL_PAD_EIM_A16__EIM_ADDR16		0xb0f1
+			MX6QDL_PAD_EIM_A17__EIM_ADDR17		0xb0f1
+			MX6QDL_PAD_EIM_A18__EIM_ADDR18		0xb0f1
+			MX6QDL_PAD_EIM_CS0__EIM_CS0_B		0xb0f1
+			MX6QDL_PAD_EIM_CS1__EIM_CS1_B		0xb0f1
+			MX6QDL_PAD_EIM_LBA__EIM_LBA_B		0xb0f1
+			MX6QDL_PAD_EIM_OE__EIM_OE_B		0xb0f1
+			MX6QDL_PAD_EIM_RW__EIM_RW		0xb0f1
+			MX6QDL_PAD_EIM_WAIT__EIM_WAIT_B		0xb0f1
+			MX6QDL_PAD_EIM_BCLK__EIM_BCLK		0xb0f1
+		>;
+	};
+
+	pinctrl_gpio_keys_novena: gpiokeysgrp-novena {
+		fsl,pins = <
+			/* User button */
+			MX6QDL_PAD_KEY_COL4__GPIO4_IO14		0x1b0b0
+			/* PCIe Wakeup */
+			MX6QDL_PAD_EIM_D22__GPIO3_IO22		0x1f0e0
+			/* Lid switch */
+			MX6QDL_PAD_KEY_COL3__GPIO4_IO12		0x1b0b0
+		>;
+	};
+
+	pinctrl_hdmi_novena: hdmigrp-novena {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE	0x1f8b0
+			MX6QDL_PAD_EIM_A24__GPIO5_IO04		0x1b0b1
+		>;
+	};
+
+	pinctrl_i2c1_novena: i2c1grp-novena {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__I2C1_SCL		0x4001b8b1
+			MX6QDL_PAD_EIM_D28__I2C1_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c2_novena: i2c2grp-novena {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_EB2__I2C2_SCL		0x4001b8b1
+			MX6QDL_PAD_EIM_D16__I2C2_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c3_novena: i2c3grp-novena {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D17__I2C3_SCL		0x4001b8b1
+			MX6QDL_PAD_EIM_D18__I2C3_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_kpp_novena: kppgrp-novena {
+		fsl,pins = <
+			/* Front panel button */
+			MX6QDL_PAD_KEY_ROW1__KEY_ROW1		0x1b0b1
+			/* Fake column driver, not connected */
+			MX6QDL_PAD_KEY_COL1__KEY_COL1		0x1b0b1
+		>;
+	};
+
+	pinctrl_leds_novena: ledsgrp-novena {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_DAT3__GPIO1_IO21		0x1b0b1
+		>;
+	};
+
+	pinctrl_pcie_novena: pciegrp-novena {
+		fsl,pins = <
+			/* Reset */
+			MX6QDL_PAD_EIM_D29__GPIO3_IO29		0x1b0b1
+			/* Power On */
+			MX6QDL_PAD_GPIO_17__GPIO7_IO12		0x1b0b1
+			/* Wifi kill */
+			MX6QDL_PAD_EIM_A22__GPIO2_IO16		0x1b0b1
+		>;
+	};
+
+	pinctrl_sata_novena: satagrp-novena {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D30__GPIO3_IO30		0x1b0b1
+		>;
+	};
+
+	pinctrl_senoko_novena: senokogrp-novena {
+		fsl,pins = <
+			/* Senoko IRQ line */
+			MX6QDL_PAD_SD1_CLK__GPIO1_IO20		0x13048
+			/* Senoko reset line */
+			MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21	0x1b0b1
+		>;
+	};
+
+	pinctrl_sound_novena: soundgrp-novena {
+		fsl,pins = <
+			/* Audio power regulator */
+			MX6QDL_PAD_DISP0_DAT23__GPIO5_IO17	0x1b0b1
+			/* Headphone plug */
+			MX6QDL_PAD_DISP0_DAT21__GPIO5_IO15	0x1b0b1
+			MX6QDL_PAD_GPIO_0__CCM_CLKO1		0x000b0
+		>;
+	};
+
+	pinctrl_stmpe_novena: stmpegrp-novena {
+		fsl,pins = <
+			/* Touchscreen interrupt */
+			MX6QDL_PAD_DISP0_DAT19__GPIO5_IO13	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart2_novena: uart2grp-novena {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D26__UART2_TX_DATA	0x1b0b1
+			MX6QDL_PAD_EIM_D27__UART2_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart3_novena: uart3grp-novena {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D24__UART3_TX_DATA	0x1b0b1
+			MX6QDL_PAD_EIM_D25__UART3_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart4_novena: uart4grp-novena {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT12__UART4_TX_DATA	0x1b0b1
+			MX6QDL_PAD_CSI0_DAT13__UART4_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg_novena: usbotggrp-novena {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID	0x17059
+		>;
+	};
+
+	pinctrl_usdhc2_novena: usdhc2grp-novena {
+		fsl,pins = <
+			MX6QDL_PAD_SD2_CMD__SD2_CMD		0x170f9
+			MX6QDL_PAD_SD2_CLK__SD2_CLK		0x100f9
+			MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x170f9
+			MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x170f9
+			MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x170f9
+			MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x170f9
+			/* Write protect */
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x1b0b1
+			/* Card detect */
+			MX6QDL_PAD_GPIO_4__GPIO1_IO04		0x1b0b1
+		>;
+	};
+
+	pinctrl_usdhc3_novena: usdhc3grp-novena {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x170f9
+			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x100f9
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x170f9
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x170f9
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x170f9
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x170f9
+		>;
+	};
+};

arch/arm/dts/imx6q-wandboard-revb1.dts

@@ -0,0 +1,23 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * Author: Fabio Estevam <fabio.estevam@freescale.com>
+ */
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-wandboard-revb1.dtsi"
+
+/ {
+	model = "Wandboard i.MX6 Quad Board rev B1";
+	compatible = "wand,imx6q-wandboard", "fsl,imx6q";
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0x80000000>;
+	};
+};
+
+&sata {
+	status = "okay";
+};

arch/arm/dts/imx6qdl-u-boot.dtsi

@@ -4,6 +4,10 @@
  */
 
 / {
+	aliases {
+		usb0 = &usbotg;
+	};
+
 	soc {
 		u-boot,dm-spl;
 

arch/arm/dts/imx6qdl-wandboard-revb1.dtsi

@@ -1,13 +1,8 @@
-/*
- * Copyright 2013 Freescale Semiconductor, Inc.
- *
- * Author: Fabio Estevam <fabio.estevam@freescale.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- */
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright 2013 Freescale Semiconductor, Inc.
+//
+// Author: Fabio Estevam <fabio.estevam@freescale.com>
 
 #include "imx6qdl-wandboard.dtsi"
 

arch/arm/dts/imx6qdl-wandboard-revd1.dtsi

@@ -0,0 +1,195 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright 2013 Freescale Semiconductor, Inc.
+//
+// Author: Fabio Estevam <fabio.estevam@freescale.com>
+
+#include "imx6qdl-wandboard.dtsi"
+
+/ {
+	reg_eth_phy: regulator-eth-phy {
+		compatible = "regulator-fixed";
+		regulator-name = "ETH_PHY";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio7 13 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c2>;
+	status = "okay";
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	pmic: pfuze100@8 {
+		compatible = "fsl,pfuze100";
+		reg = <0x08>;
+
+		regulators {
+			sw1a_reg: sw1ab {
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1875000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			sw1c_reg: sw1c {
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1875000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			sw2_reg: sw2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			sw3a_reg: sw3a {
+				regulator-min-microvolt = <400000>;
+				regulator-max-microvolt = <1975000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3b_reg: sw3b {
+				regulator-min-microvolt = <400000>;
+				regulator-max-microvolt = <1975000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw4_reg: sw4 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			swbst_reg: swbst {
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5150000>;
+			};
+
+			snvs_reg: vsnvs {
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vref_reg: vrefddr {
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vgen1_reg: vgen1 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+			};
+
+			vgen2_reg: vgen2 {
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vgen3_reg: vgen3 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen4_reg: vgen4 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen5_reg: vgen5 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen6_reg: vgen6 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&fec {
+	phy-supply = <&reg_eth_phy>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-0 = <&pinctrl_hog>;
+
+	imx6qdl-wandboard {
+		pinctrl_hog: hoggrp {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_D22__USB_OTG_PWR		0x80000000	/* USB Power Enable */
+				MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x80000000	/* USDHC1 CD */
+				MX6QDL_PAD_EIM_DA9__GPIO3_IO09		0x80000000	/* uSDHC3 CD */
+				MX6QDL_PAD_EIM_D29__GPIO3_IO29   	0x1f0b1		/* RGMII PHY reset */
+			>;
+		};
+
+		pinctrl_enet: enetgrp {
+			fsl,pins = <
+				MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+				MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+				MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b030
+				MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b030
+				MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b030
+				MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b030
+				MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b030
+				MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b030
+				MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b0b0
+				MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
+				MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b030
+				MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b030
+				MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
+				MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
+				MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
+				MX6QDL_PAD_GPIO_6__ENET_IRQ		0x000b1
+			>;
+		};
+
+		pinctrl_i2c3: i2c3grp {
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_5__I2C3_SCL		0x4001b8b1
+				MX6QDL_PAD_GPIO_16__I2C3_SDA		0x4001b8b1
+			>;
+		};
+
+		pinctrl_spdif: spdifgrp {
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_19__SPDIF_OUT		0x1b0b0
+			>;
+		};
+	};
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	bus-width = <4>;
+	no-1-8-v;
+	non-removable;
+	status = "okay";
+};

arch/arm/dts/imx6qdl-wandboard.dtsi

@@ -8,6 +8,14 @@
 #include <dt-bindings/gpio/gpio.h>
 
 / {
+	aliases {
+		mmc0 = &usdhc3;
+	};
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
 	sound {
 		compatible = "fsl,imx6-wandboard-sgtl5000",
 			     "fsl,imx-audio-sgtl5000";
@@ -90,107 +98,6 @@
 		VDDIO-supply = <&reg_3p3v>;
 		lrclk-strength = <3>;
 	};
-
-	pmic: pfuze100@8 {
-		compatible = "fsl,pfuze100";
-		reg = <0x08>;
-
-		regulators {
-			sw1a_reg: sw1ab {
-				regulator-min-microvolt = <300000>;
-				regulator-max-microvolt = <1875000>;
-				regulator-boot-on;
-				regulator-always-on;
-				regulator-ramp-delay = <6250>;
-			};
-
-			sw1c_reg: sw1c {
-				regulator-min-microvolt = <300000>;
-				regulator-max-microvolt = <1875000>;
-				regulator-boot-on;
-				regulator-always-on;
-				regulator-ramp-delay = <6250>;
-			};
-
-			sw2_reg: sw2 {
-				regulator-min-microvolt = <800000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-boot-on;
-				regulator-always-on;
-				regulator-ramp-delay = <6250>;
-			};
-
-			sw3a_reg: sw3a {
-				regulator-min-microvolt = <400000>;
-				regulator-max-microvolt = <1975000>;
-				regulator-boot-on;
-				regulator-always-on;
-			};
-
-			sw3b_reg: sw3b {
-				regulator-min-microvolt = <400000>;
-				regulator-max-microvolt = <1975000>;
-				regulator-boot-on;
-				regulator-always-on;
-			};
-
-			sw4_reg: sw4 {
-				regulator-min-microvolt = <800000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-always-on;
-			};
-
-			swbst_reg: swbst {
-				regulator-min-microvolt = <5000000>;
-				regulator-max-microvolt = <5150000>;
-			};
-
-			snvs_reg: vsnvs {
-				regulator-min-microvolt = <1000000>;
-				regulator-max-microvolt = <3000000>;
-				regulator-boot-on;
-				regulator-always-on;
-			};
-
-			vref_reg: vrefddr {
-				regulator-boot-on;
-				regulator-always-on;
-			};
-
-			vgen1_reg: vgen1 {
-				regulator-min-microvolt = <800000>;
-				regulator-max-microvolt = <1550000>;
-			};
-
-			vgen2_reg: vgen2 {
-				regulator-min-microvolt = <800000>;
-				regulator-max-microvolt = <1550000>;
-			};
-
-			vgen3_reg: vgen3 {
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <3300000>;
-			};
-
-			vgen4_reg: vgen4 {
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-always-on;
-			};
-
-			vgen5_reg: vgen5 {
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-always-on;
-			};
-
-			vgen6_reg: vgen6 {
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-always-on;
-			};
-		};
-	};
 };
 
 &iomuxc {
@@ -321,7 +228,7 @@
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-reset-gpios = <&gpio3 29 GPIO_ACTIVE_LOW>;
 	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
 			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;

arch/arm/dts/imx6qp-wandboard-revd1.dts

@@ -0,0 +1,23 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * Author: Fabio Estevam <fabio.estevam@freescale.com>
+ */
+/dts-v1/;
+#include "imx6qp.dtsi"
+#include "imx6qdl-wandboard-revd1.dtsi"
+
+/ {
+	model = "Wandboard i.MX6 QuadPlus Board revD1";
+	compatible = "wand,imx6qp-wandboard", "fsl,imx6qp";
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0x80000000>;
+	};
+};
+
+&sata {
+	status = "okay";
+};

arch/arm/dts/imx6sx-softing-vining-2000.dts

@@ -0,0 +1,578 @@
+/*
+ * Copyright (C) 2016 Christoph Fritz <chf.fritz@googlemail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include "imx6sx.dtsi"
+
+/ {
+	model = "Softing VIN|ING 2000";
+	compatible = "samtec,imx6sx-vining-2000", "fsl,imx6sx";
+
+	aliases {
+		mmc0 = &usdhc4;
+		mmc1 = &usdhc2;
+	};
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x40000000>;
+	};
+
+	reg_usb_otg1_vbus: regulator-usb_otg1_vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg1_vbus";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usb_otg1>;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_peri_3v3: regulator-peri_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "peri_3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	pwmleds {
+		compatible = "pwm-leds";
+
+		red {
+			label = "red";
+			max-brightness = <255>;
+			pwms = <&pwm6 0 50000>;
+		};
+
+		green {
+			label = "green";
+			max-brightness = <255>;
+			pwms = <&pwm2 0 50000>;
+		};
+
+		blue {
+			label = "blue";
+			max-brightness = <255>;
+			pwms = <&pwm1 0 50000>;
+		};
+	};
+};
+
+&adc1 {
+	vref-supply = <&reg_peri_3v3>;
+	status = "okay";
+};
+
+&cpu0 {
+	/*
+	 * This board has a shared rail of reg_arm and reg_soc (supplied by
+	 * sw1a_reg) which is modeled below, but still this module behaves
+	 * unstable without higher voltages. Hence, set higher voltages here.
+	 */
+	operating-points = <
+		/* kHz    uV */
+		996000  1250000
+		792000  1175000
+		396000  1175000
+		198000  1175000
+		>;
+	fsl,soc-operating-points = <
+		/* ARM kHz  SOC uV */
+		996000	1250000
+		792000	1175000
+		396000	1175000
+		198000  1175000
+	>;
+};
+
+&ecspi4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi4>;
+	cs-gpios = <&gpio7 4 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet1>;
+	phy-supply = <&reg_peri_3v3>;
+	phy-reset-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+	phy-reset-duration = <5>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy0>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet0-phy@0 {
+			reg = <0>;
+			max-speed = <100>;
+			interrupt-parent = <&gpio2>;
+			interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
+		};
+	};
+};
+
+&fec2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet2>;
+	phy-supply = <&reg_peri_3v3>;
+	phy-reset-gpios = <&gpio5 21 GPIO_ACTIVE_LOW>;
+	phy-reset-duration = <5>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy1>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy1: ethernet1-phy@0 {
+			reg = <0>;
+			max-speed = <100>;
+			interrupt-parent = <&gpio2>;
+			interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
+		};
+	};
+};
+
+&flexcan1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan1>;
+	status = "okay";
+};
+
+&flexcan2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan2>;
+	status = "okay";
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	proximity: sx9500@28 {
+		compatible = "semtech,sx9500";
+		reg = <0x28>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_sx9500>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpio2 10 GPIO_ACTIVE_HIGH>;
+	};
+
+	pmic: pfuze100@8 {
+		compatible = "fsl,pfuze200";
+		reg = <0x08>;
+
+		regulators {
+			sw1a_reg: sw1ab {
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1875000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			sw2_reg: sw2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3a_reg: sw3a {
+				regulator-min-microvolt = <400000>;
+				regulator-max-microvolt = <1975000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3b_reg: sw3b {
+				regulator-min-microvolt = <400000>;
+				regulator-max-microvolt = <1975000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			snvs_reg: vsnvs {
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vref_reg: vrefddr {
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vgen1_reg: vgen1 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+				regulator-always-on;
+			};
+
+			vgen2_reg: vgen2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+			};
+
+			vgen3_reg: vgen3 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen4_reg: vgen4 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen5_reg: vgen5 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen6_reg: vgen6 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpios>;
+
+	pinctrl_ecspi4: ecspi4grp {
+		fsl,pins = <
+			MX6SX_PAD_SD3_CLK__ECSPI4_SCLK		0x130b1
+			MX6SX_PAD_SD3_DATA3__ECSPI4_MISO	0x130b1
+			MX6SX_PAD_SD3_CMD__ECSPI4_MOSI		0x130b1
+			MX6SX_PAD_SD3_DATA2__GPIO7_IO_4		0x30b0
+		>;
+	};
+
+	pinctrl_enet1: enet1grp {
+		fsl,pins = <
+			MX6SX_PAD_RGMII1_RD0__ENET1_RX_DATA_0	0x30c1
+			MX6SX_PAD_RGMII1_RD1__ENET1_RX_DATA_1	0x30c1
+			MX6SX_PAD_RGMII1_TD0__ENET1_TX_DATA_0	0xa0f9
+			MX6SX_PAD_RGMII1_TD1__ENET1_TX_DATA_1	0xa0f9
+			MX6SX_PAD_RGMII1_RX_CTL__ENET1_RX_EN	0x30c1
+			MX6SX_PAD_RGMII1_TX_CTL__ENET1_TX_EN	0xa0f9
+			MX6SX_PAD_ENET1_TX_CLK__ENET1_REF_CLK1	0x4000a038
+			/* LAN8720 PHY Reset */
+			MX6SX_PAD_RGMII1_TD3__GPIO5_IO_9	0x10b0
+			/* MDIO */
+			MX6SX_PAD_ENET1_MDC__ENET1_MDC		0xa0f9
+			MX6SX_PAD_ENET1_MDIO__ENET1_MDIO	0xa0f9
+			/* IRQ from PHY */
+			MX6SX_PAD_KEY_ROW2__GPIO2_IO_17		0x10b0
+		>;
+	};
+
+	pinctrl_enet2: enet2grp {
+		fsl,pins = <
+			MX6SX_PAD_RGMII2_TD0__ENET2_TX_DATA_0	0x1b0b0
+			MX6SX_PAD_RGMII2_TD1__ENET2_TX_DATA_1	0x1b0b0
+			MX6SX_PAD_RGMII2_RD0__ENET2_RX_DATA_0	0x1b0b0
+			MX6SX_PAD_RGMII2_RD1__ENET2_RX_DATA_1	0x1b0b0
+			MX6SX_PAD_RGMII2_RX_CTL__ENET2_RX_EN	0x1b0b0
+			MX6SX_PAD_RGMII2_TX_CTL__ENET2_TX_EN	0x1b0b0
+			MX6SX_PAD_ENET2_TX_CLK__ENET2_REF_CLK2	0x4000a038
+			/* LAN8720 PHY Reset */
+			MX6SX_PAD_RGMII2_TD3__GPIO5_IO_21	0x10b0
+			/* MDIO */
+			MX6SX_PAD_ENET1_COL__ENET2_MDC		0xa0f9
+			MX6SX_PAD_ENET1_CRS__ENET2_MDIO		0xa0f9
+			/* IRQ from PHY */
+			MX6SX_PAD_KEY_ROW4__GPIO2_IO_19		0x10b0
+		>;
+	};
+
+	pinctrl_flexcan1: flexcan1grp {
+		fsl,pins = <
+			MX6SX_PAD_QSPI1B_DQS__CAN1_TX		0x1b0b0
+			MX6SX_PAD_QSPI1A_SS1_B__CAN1_RX		0x1b0b0
+		>;
+	};
+
+	pinctrl_flexcan2: flexcan2grp {
+		fsl,pins = <
+			MX6SX_PAD_QSPI1B_SS1_B__CAN2_RX		0x1b0b0
+			MX6SX_PAD_QSPI1A_DQS__CAN2_TX		0x1b0b0
+		>;
+	};
+
+	pinctrl_gpios: gpiosgrp {
+		fsl,pins = <
+			/* reset external uC */
+			MX6SX_PAD_QSPI1A_DATA3__GPIO4_IO_19	0x10b0
+			/* IRQ from external uC */
+			MX6SX_PAD_KEY_ROW0__GPIO2_IO_15		0x10b0
+			/* overcurrent detection */
+			MX6SX_PAD_GPIO1_IO08__GPIO1_IO_8	0x10b0
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6SX_PAD_GPIO1_IO01__I2C1_SDA		0x4001b8b1
+			MX6SX_PAD_GPIO1_IO00__I2C1_SCL		0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6SX_PAD_NAND_ALE__I2C3_SDA		0x4001b8b1
+			MX6SX_PAD_NAND_CLE__I2C3_SCL		0x4001b8b1
+		>;
+	};
+
+	pinctrl_pwm1: pwm1grp-1 {
+		fsl,pins = <
+			/* blue LED */
+			MX6SX_PAD_RGMII2_RD3__PWM1_OUT		0x1b0b1
+		>;
+	};
+
+	pinctrl_pwm2: pwm2grp-1 {
+		fsl,pins = <
+			/* green LED */
+			MX6SX_PAD_RGMII2_RD2__PWM2_OUT		0x1b0b1
+		>;
+	};
+
+	pinctrl_pwm6: pwm6grp-1 {
+		fsl,pins = <
+			/* red LED */
+			MX6SX_PAD_RGMII2_TD2__PWM6_OUT		0x1b0b1
+		>;
+	};
+
+	pinctrl_sx9500: sx9500grp {
+		fsl,pins = <
+			/* Reset */
+			MX6SX_PAD_KEY_COL0__GPIO2_IO_10		0x838
+			/* IRQ */
+			MX6SX_PAD_KEY_ROW1__GPIO2_IO_16		0x70e0
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6SX_PAD_GPIO1_IO04__UART1_TX		0x1b0b1
+			MX6SX_PAD_GPIO1_IO05__UART1_RX		0x1b0b1
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6SX_PAD_GPIO1_IO06__UART2_TX		0x1b0b1
+			MX6SX_PAD_GPIO1_IO07__UART2_RX		0x1b0b1
+		>;
+	};
+
+	pinctrl_usb_otg1: usbotg1grp {
+		fsl,pins = <
+			MX6SX_PAD_GPIO1_IO09__GPIO1_IO_9	0x10b0
+		>;
+	};
+
+	pinctrl_usb_otg1_id: usbotg1idgrp {
+		fsl,pins = <
+			MX6SX_PAD_GPIO1_IO10__ANATOP_OTG1_ID	0x17059
+		>;
+	};
+
+	pinctrl_usdhc2_50mhz: usdhc2grp-50mhz {
+		fsl,pins = <
+			MX6SX_PAD_SD2_CLK__USDHC2_CLK		0x10059
+			MX6SX_PAD_SD2_CMD__USDHC2_CMD		0x17059
+			MX6SX_PAD_SD2_DATA0__USDHC2_DATA0	0x17059
+			MX6SX_PAD_SD2_DATA1__USDHC2_DATA1	0x17059
+			MX6SX_PAD_SD2_DATA2__USDHC2_DATA2	0x17059
+			MX6SX_PAD_SD2_DATA3__USDHC2_DATA3	0x17059
+			MX6SX_PAD_LCD1_VSYNC__GPIO3_IO_28	0x1b000
+			MX6SX_PAD_LCD1_HSYNC__GPIO3_IO_26	0x10b0
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2grp-100mhz {
+		fsl,pins = <
+			MX6SX_PAD_SD2_CLK__USDHC2_CLK		0x100b9
+			MX6SX_PAD_SD2_CMD__USDHC2_CMD		0x170b9
+			MX6SX_PAD_SD2_DATA0__USDHC2_DATA0	0x170b9
+			MX6SX_PAD_SD2_DATA1__USDHC2_DATA1	0x170b9
+			MX6SX_PAD_SD2_DATA2__USDHC2_DATA2	0x170b9
+			MX6SX_PAD_SD2_DATA3__USDHC2_DATA3	0x170b9
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2grp-200mhz {
+		fsl,pins = <
+			MX6SX_PAD_SD2_CLK__USDHC2_CLK		0x100f9
+			MX6SX_PAD_SD2_CMD__USDHC2_CMD		0x170f9
+			MX6SX_PAD_SD2_DATA0__USDHC2_DATA0	0x170f9
+			MX6SX_PAD_SD2_DATA1__USDHC2_DATA1	0x170f9
+			MX6SX_PAD_SD2_DATA2__USDHC2_DATA2	0x170f9
+			MX6SX_PAD_SD2_DATA3__USDHC2_DATA3	0x170f9
+		>;
+	};
+
+	pinctrl_usdhc4_50mhz: usdhc4grp-50mhz {
+		fsl,pins = <
+			MX6SX_PAD_SD4_CLK__USDHC4_CLK		0x10059
+			MX6SX_PAD_SD4_CMD__USDHC4_CMD		0x17059
+			MX6SX_PAD_SD4_DATA0__USDHC4_DATA0	0x17059
+			MX6SX_PAD_SD4_DATA1__USDHC4_DATA1	0x17059
+			MX6SX_PAD_SD4_DATA2__USDHC4_DATA2	0x17059
+			MX6SX_PAD_SD4_DATA3__USDHC4_DATA3	0x17059
+			MX6SX_PAD_SD4_DATA4__USDHC4_DATA4	0x17059
+			MX6SX_PAD_SD4_DATA5__USDHC4_DATA5	0x17059
+			MX6SX_PAD_SD4_DATA6__USDHC4_DATA6	0x17059
+			MX6SX_PAD_SD4_DATA7__USDHC4_DATA7	0x17059
+			MX6SX_PAD_SD4_RESET_B__USDHC4_RESET_B	0x17068
+		>;
+	};
+
+	pinctrl_usdhc4_100mhz: usdhc4-100mhz {
+		fsl,pins = <
+			MX6SX_PAD_SD4_CLK__USDHC4_CLK		0x100b9
+			MX6SX_PAD_SD4_CMD__USDHC4_CMD		0x170b9
+			MX6SX_PAD_SD4_DATA0__USDHC4_DATA0	0x170b9
+			MX6SX_PAD_SD4_DATA1__USDHC4_DATA1	0x170b9
+			MX6SX_PAD_SD4_DATA2__USDHC4_DATA2	0x170b9
+			MX6SX_PAD_SD4_DATA3__USDHC4_DATA3	0x170b9
+			MX6SX_PAD_SD4_DATA4__USDHC4_DATA4	0x170b9
+			MX6SX_PAD_SD4_DATA5__USDHC4_DATA5	0x170b9
+			MX6SX_PAD_SD4_DATA6__USDHC4_DATA6	0x170b9
+			MX6SX_PAD_SD4_DATA7__USDHC4_DATA7	0x170b9
+		>;
+	};
+
+	pinctrl_usdhc4_200mhz: usdhc4-200mhz {
+		fsl,pins = <
+			MX6SX_PAD_SD4_CLK__USDHC4_CLK		0x100f9
+			MX6SX_PAD_SD4_CMD__USDHC4_CMD		0x170f9
+			MX6SX_PAD_SD4_DATA0__USDHC4_DATA0	0x170f9
+			MX6SX_PAD_SD4_DATA1__USDHC4_DATA1	0x170f9
+			MX6SX_PAD_SD4_DATA2__USDHC4_DATA2	0x170f9
+			MX6SX_PAD_SD4_DATA3__USDHC4_DATA3	0x170f9
+			MX6SX_PAD_SD4_DATA4__USDHC4_DATA4	0x170f9
+			MX6SX_PAD_SD4_DATA5__USDHC4_DATA5	0x170f9
+			MX6SX_PAD_SD4_DATA6__USDHC4_DATA6	0x170f9
+			MX6SX_PAD_SD4_DATA7__USDHC4_DATA7	0x170f9
+		>;
+	};
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "okay";
+};
+
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>;
+	status = "okay";
+};
+
+&pwm6 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm6>;
+	status = "okay";
+};
+
+&reg_arm {
+	vin-supply = <&sw1a_reg>;
+};
+
+&reg_soc {
+	vin-supply = <&sw1a_reg>;
+};
+
+&snvs_poweroff {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&usbotg1 {
+	vbus-supply = <&reg_usb_otg1_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb_otg1_id>;
+	status = "okay";
+};
+
+&usbotg2 {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2_50mhz>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+	cd-gpios = <&gpio3 28 GPIO_ACTIVE_LOW>;
+	keep-power-in-suspend;
+	status = "okay";
+};
+
+&usdhc4 {
+	/* hs200-mode is currently unsupported because Vccq is on 3.1V, but
+	 * not on necessary 1.8V.
+	 */
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc4_50mhz>;
+	pinctrl-1 = <&pinctrl_usdhc4_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc4_200mhz>;
+	bus-width = <8>;
+	keep-power-in-suspend;
+	non-removable;
+	cap-mmc-hw-reset;
+	status = "okay";
+};

arch/arm/dts/imx6ul-phycore-segin.dts

@@ -16,7 +16,8 @@
 
 /dts-v1/;
 
-#include "imx6ul-pcl063.dtsi"
+#include "imx6ul.dtsi"
+#include "pcl063-common.dtsi"
 
 / {
 	model = "Phytec phyBOARD-i.MX6UL-Segin SBC";
@@ -24,6 +25,10 @@
 		     "fsl,imx6ul";
 };
 
+&gpmi {
+	status = "okay";
+};
+
 &i2c1 {
 	i2c_rtc: rtc@68 {
 		compatible = "microcrystal,rv4162";

arch/arm/dts/imx6ull-colibri.dts

@@ -220,7 +220,7 @@
 
 /* Colibri USBC */
 &usbotg1 {
-	dr_mode = "otg";
+	dr_mode = "host";
 	srp-disable;
 	hnp-disable;
 	adp-disable;

arch/arm/dts/imx6ull-phycore-segin.dts

@@ -0,0 +1,70 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2019 Parthiban Nallathambi <parthitce@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "imx6ull.dtsi"
+#include "pcl063-common.dtsi"
+
+/ {
+	model = "Phytec phyBOARD-i.MX6ULL-Segin SBC";
+	compatible = "phytec,phyboard-imx6ull-segin", "phytec,imx6ull-pcl063",
+		     "fsl,imx6ull";
+};
+
+&i2c1 {
+	i2c_rtc: rtc@68 {
+		compatible = "microcrystal,rv4162";
+		reg = <0x68>;
+		status = "okay";
+	};
+};
+
+&uart5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart5>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&usdhc2 {
+	status = "okay";
+};
+
+&usbotg1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb_otg1_id>;
+	dr_mode = "otg";
+	srp-disable;
+	hnp-disable;
+	adp-disable;
+	status = "okay";
+};
+
+&usbotg2 {
+	dr_mode = "host";
+	disable-over-current;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+
+	pinctrl_uart5: uart5grp {
+		fsl,pins = <
+			MX6UL_PAD_UART5_TX_DATA__UART5_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX	0x1b0b1
+			MX6UL_PAD_GPIO1_IO08__UART5_DCE_RTS	0x1b0b1
+			MX6UL_PAD_GPIO1_IO09__UART5_DCE_CTS	0x1b0b1
+		>;
+	};
+
+	pinctrl_usb_otg1_id: usbotg1idgrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO00__ANATOP_OTG1_ID    0x17059
+		>;
+	};
+
+};

arch/arm/dts/imx6ull-u-boot.dtsi

@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2019 Parthiban Nallathambi <parthitce@gmail.com>
+ */
+
+/ {
+	soc {
+		u-boot,dm-spl;
+	};
+};
+
+&aips1 {
+	u-boot,dm-spl;
+};
+
+&aips2 {
+	u-boot,dm-spl;
+};
+
+&aips3 {
+	u-boot,dm-spl;
+};
+
+&gpio1 {
+	u-boot,dm-spl;
+};
+
+&gpio4 {
+	u-boot,dm-spl;
+};
+
+&iomuxc {
+	u-boot,dm-spl;
+};

arch/arm/dts/imx7-colibri-emmc.dts

@@ -11,13 +11,34 @@
 	compatible = "toradex,imx7d-colibri-emmc", "fsl,imx7d";
 
 	aliases {
+		u-boot,dm-pre-reloc;
 		mmc0 = &usdhc3;
 		mmc1 = &usdhc1;
+		display1 = &lcdif;
+		usb0 = &usbotg1; /* required for ums */
 	};
 
 	chosen {
 		stdout-path = &uart1;
 	};
+
+	reg_5v0: regulator-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_usbh_vbus: regulator-usbh-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbh_reg>;
+		regulator-name = "VCC_USB[1-4]";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio4 7 GPIO_ACTIVE_LOW>;
+		vin-supply = <&reg_5v0>;
+	};
 };
 
 &usdhc3 {
@@ -44,4 +65,30 @@
 			MX7D_PAD_SD3_STROBE__SD3_STROBE         0x19
 		>;
 	};
+
+	pinctrl_usbh_reg: gpio-usbh-vbus {
+		fsl,pins = <
+			MX7D_PAD_UART3_CTS_B__GPIO4_IO7	0x14
+		>;
+	};
+};
+
+/* Colibri USBC */
+&usbotg1 {
+	/*
+	 * usbotg1 on Colibri iMX7 can function in both host/otg modes.
+	 * Gadget stack currently does not look at this at all while
+	 * the host stack refuses to bind/load if it is not set to host
+	 * (it obviously won't be enumerated during usb start invocation
+	 * if dr_mode = "otg")
+	 */
+	dr_mode = "host";
+	status = "okay";
+};
+
+/* Colibri USBH */
+&usbotg2 {
+	dr_mode = "host";
+	vbus-supply = <&reg_usbh_vbus>;
+	status = "okay";
 };

arch/arm/dts/imx7-colibri-rawnand.dts

@@ -13,6 +13,28 @@
 	chosen {
 		stdout-path = &uart1;
 	};
+
+	aliases {
+		usb0 = &usbotg1; /* required for ums */
+	};
+
+	reg_5v0: regulator-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_usbh_vbus: regulator-usbh-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbh_reg>;
+		regulator-name = "VCC_USB[1-4]";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio4 7 GPIO_ACTIVE_LOW>;
+		vin-supply = <&reg_5v0>;
+	};
 };
 
 &gpmi {
@@ -43,4 +65,30 @@
 			MX7D_PAD_SD3_DATA7__NAND_DATA07		0x71
 		>;
 	};
+
+	pinctrl_usbh_reg: gpio-usbh-vbus {
+		fsl,pins = <
+			MX7D_PAD_UART3_CTS_B__GPIO4_IO7	0x14
+		>;
+	};
+};
+
+/* Colibri USBC */
+&usbotg1 {
+	/*
+	 * usbotg1 on Colibri iMX7 can function in both host/otg modes.
+	 * Gadget stack currently does not look at this at all while
+	 * the host stack refuses to bind/load if it is not set to host
+	 * (it obviously won't be enumerated during usb start invocation
+	 * if dr_mode = "otg")
+	 */
+	dr_mode = "host";
+	status = "okay";
+};
+
+/* Colibri USBH */
+&usbotg2 {
+	dr_mode = "host";
+	vbus-supply = <&reg_usbh_vbus>;
+	status = "okay";
 };

arch/arm/dts/imx7-colibri.dtsi

@@ -111,3 +111,31 @@
 		>;
 	};
 };
+
+&lcdif {
+	u-boot,dm-pre-reloc;
+	status = "okay";
+
+	display-timings {
+		native-mode = <&timing_vga>;
+
+		/* Standard VGA timing */
+		timing_vga: 640x480 {
+			u-boot,dm-pre-reloc;
+			clock-frequency = <25175000>;
+			hactive = <640>;
+			vactive = <480>;
+			hback-porch = <48>;
+			hfront-porch = <16>;
+			vback-porch = <33>;
+			vfront-porch = <10>;
+			hsync-len = <96>;
+			vsync-len = <2>;
+
+			de-active = <1>;
+			hsync-active = <0>;
+			vsync-active = <0>;
+			pixelclk-active = <0>;
+		};
+	};
+};

arch/arm/dts/ls1021a.dtsi

@@ -406,8 +406,7 @@
 
 		sata: sata@3200000 {
 			compatible = "fsl,ls1021a-ahci";
-			reg = <0x0 0x3200000 0x0 0x10000 /* ccsr sata base */
-			       0x0 0x20220520 0x0 0x4>;	 /* ecc sata addr*/
+			reg = <0x3200000 0x10000 0x20220520 0x4>;
 			reg-names = "sata-base", "ecc-addr";
 			interrupts = <0 101 4>;
 			status = "disabled";

arch/arm/dts/meson-g12a-u-boot.dtsi

@@ -0,0 +1,216 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre, SAS.
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+/ {
+	soc {
+		ethmac: ethernet@ff3f0000 {
+			compatible = "amlogic,meson-axg-dwmac", "snps,dwmac-3.710",
+				     "snps,dwmac";
+			reg = <0x0 0xff3f0000 0x0 0x10000
+			       0x0 0xff634540 0x0 0x8>;
+			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq";
+			clocks = <&clkc CLKID_ETH>,
+				 <&clkc CLKID_FCLK_DIV2>,
+				 <&clkc CLKID_MPLL2>;
+			clock-names = "stmmaceth", "clkin0", "clkin1";
+			status = "disabled";
+
+			mdio0: mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "snps,dwmac-mdio";
+			};
+		};
+
+		sd_emmc_a: sd@ffe03000 {
+			compatible = "amlogic,meson-axg-mmc";
+			reg = <0x0 0xffe03000 0x0 0x800>;
+			interrupts = <GIC_SPI 189 IRQ_TYPE_EDGE_RISING>;
+			status = "disabled";
+			clocks = <&clkc CLKID_SD_EMMC_A>,
+				 <&clkc CLKID_SD_EMMC_A_CLK0>,
+				 <&clkc CLKID_FCLK_DIV2>;
+			clock-names = "core", "clkin0", "clkin1";
+			resets = <&reset RESET_SD_EMMC_A>;
+		};
+
+		sd_emmc_b: sd@ffe05000 {
+			compatible = "amlogic,meson-axg-mmc";
+			reg = <0x0 0xffe05000 0x0 0x800>;
+			interrupts = <GIC_SPI 190 IRQ_TYPE_EDGE_RISING>;
+			status = "disabled";
+			clocks = <&clkc CLKID_SD_EMMC_B>,
+				 <&clkc CLKID_SD_EMMC_B_CLK0>,
+				 <&clkc CLKID_FCLK_DIV2>;
+			clock-names = "core", "clkin0", "clkin1";
+			resets = <&reset RESET_SD_EMMC_B>;
+		};
+
+		sd_emmc_c: mmc@ffe07000 {
+			compatible = "amlogic,meson-axg-mmc";
+			reg = <0x0 0xffe07000 0x0 0x800>;
+			interrupts = <GIC_SPI 191 IRQ_TYPE_EDGE_RISING>;
+			status = "disabled";
+			clocks = <&clkc CLKID_SD_EMMC_C>,
+				 <&clkc CLKID_SD_EMMC_C_CLK0>,
+				 <&clkc CLKID_FCLK_DIV2>;
+			clock-names = "core", "clkin0", "clkin1";
+			resets = <&reset RESET_SD_EMMC_C>;
+		};
+	};
+};
+
+&periphs_pinctrl {
+	emmc_pins: emmc {
+		mux {
+			groups = "emmc_nand_d0",
+				 "emmc_nand_d1",
+				 "emmc_nand_d2",
+				 "emmc_nand_d3",
+				 "emmc_nand_d4",
+				 "emmc_nand_d5",
+				 "emmc_nand_d6",
+				 "emmc_nand_d7",
+				 "emmc_clk",
+				 "emmc_cmd";
+			function = "emmc";
+			bias-pull-up;
+		};
+	};
+
+	emmc_ds_pins: emmc-ds {
+		mux {
+			groups = "emmc_nand_ds";
+			function = "emmc";
+			bias-pull-down;
+		};
+	};
+
+	emmc_clk_gate_pins: emmc_clk_gate {
+		mux {
+			groups = "BOOT_8";
+			function = "gpio_periphs";
+			bias-pull-down;
+		};
+	};
+
+	eth_leds_pins: eth-leds {
+		mux {
+			groups = "eth_link_led",
+				 "eth_act_led";
+			function = "eth";
+			bias-disable;
+		};
+	};
+
+	eth_rmii_pins: eth-rmii {
+		mux {
+			groups = "eth_mdio",
+				 "eth_mdc",
+				 "eth_rgmii_rx_clk",
+				 "eth_rx_dv",
+				 "eth_rxd0",
+				 "eth_rxd1",
+				 "eth_txen",
+				 "eth_txd0",
+				 "eth_txd1";
+			function = "eth";
+			bias-disable;
+		};
+	};
+
+	eth_rgmii_pins: eth-rgmii {
+		mux {
+			groups = "eth_rxd2_rgmii",
+				 "eth_rxd3_rgmii",
+				 "eth_rgmii_tx_clk",
+				 "eth_txd2_rgmii",
+				 "eth_txd3_rgmii";
+			function = "eth";
+			bias-disable;
+		};
+	};
+
+	sdcard_c_pins: sdcard_c {
+		mux {
+			groups = "sdcard_d0_c",
+				 "sdcard_d1_c",
+				 "sdcard_d2_c",
+				 "sdcard_d3_c",
+				 "sdcard_cmd_c",
+				 "sdcard_clk_c";
+			function = "sdcard";
+			bias-pull-up;
+		};
+	};
+
+	sdcard_clk_gate_c_pins: sdcard_clk_gate_c {
+		mux {
+			groups = "GPIOC_4";
+			function = "gpio_periphs";
+			bias-pull-down;
+		};
+	};
+
+	sdcard_z_pins: sdcard_z {
+		mux {
+			groups = "sdcard_d0_z",
+				 "sdcard_d1_z",
+				 "sdcard_d2_z",
+				 "sdcard_d3_z",
+				 "sdcard_cmd_z",
+				 "sdcard_clk_z";
+			function = "sdcard";
+			bias-pull-up;
+		};
+	};
+
+	sdcard_clk_gate_z_pins: sdcard_clk_gate_z {
+		mux {
+			groups = "GPIOZ_6";
+			function = "gpio_periphs";
+			bias-pull-down;
+		};
+	};
+};
+
+&periphs {
+	eth_phy: mdio-multiplexer@4c000 {
+		compatible = "amlogic,g12a-mdio-mux";
+		reg = <0x0 0x4c000 0x0 0xa4>;
+		clocks = <&clkc CLKID_ETH_PHY>,
+			 <&xtal>,
+			 <&clkc CLKID_MPLL_5OM>;
+		clock-names = "pclk", "clkin0", "clkin1";
+		mdio-parent-bus = <&mdio0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ext_mdio: mdio@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		int_mdio: mdio@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			internal_ephy: ethernet_phy@8 {
+				compatible = "ethernet-phy-id0180.3300",
+					     "ethernet-phy-ieee802.3-c22";
+				reg = <8>;
+				max-speed = <100>;
+
+				/* FIXME: Add irq support */
+			};
+		};
+	};
+};
+
+

arch/arm/dts/meson-g12a-u200-u-boot.dtsi

@@ -0,0 +1,63 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre, SAS.
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+#include "meson-g12a-u-boot.dtsi"
+
+ / {
+	aliases {
+		ethernet0 = &ethmac;
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&ethmac {
+	status = "okay";
+	pinctrl-0 = <&eth_leds_pins>;
+	pinctrl-names = "default";
+	phy-handle = <&internal_ephy>;
+	phy-mode = "rmii";
+};
+
+
+/* SD card */
+&sd_emmc_b {
+	status = "okay";
+	pinctrl-0 = <&sdcard_c_pins>;
+	pinctrl-1 = <&sdcard_clk_gate_c_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <50000000>;
+	disable-wp;
+
+	cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddao_3v3>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+	pinctrl-1 = <&emmc_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	max-frequency = <200000000>;
+	disable-wp;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&flash_1v8>;
+};

arch/arm/dts/meson-g12a-u200.dts

@@ -6,6 +6,8 @@
 /dts-v1/;
 
 #include "meson-g12a.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/gpio/meson-g12a-gpio.h>
 
 / {
 	compatible = "amlogic,u200", "amlogic,g12a";
@@ -21,9 +23,154 @@
 		device_type = "memory";
 		reg = <0x0 0x0 0x0 0x40000000>;
 	};
+
+	cvbs-connector {
+		compatible = "composite-video-connector";
+
+		port {
+			cvbs_connector_in: endpoint {
+				remote-endpoint = <&cvbs_vdac_out>;
+			};
+		};
+	};
+
+	flash_1v8: regulator-flash_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "FLASH_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_3v3>;
+		regulator-always-on;
+	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&hdmi_tx_tmds_out>;
+			};
+		};
+	};
+
+	main_12v: regulator-main_12v {
+		compatible = "regulator-fixed";
+		regulator-name = "12V";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+	};
+
+	vcc_1v8: regulator-vcc_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_3v3>;
+		regulator-always-on;
+	};
+
+	vcc_3v3: regulator-vcc_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+		/* FIXME: actually controlled by VDDCPU_B_EN */
+	};
+
+	vcc_5v: regulator-vcc_5v {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&main_12v>;
+
+		gpio = <&gpio GPIOH_8 GPIO_OPEN_DRAIN>;
+		enable-active-high;
+	};
+
+	usb_pwr_en: regulator-usb_pwr_en {
+		compatible = "regulator-fixed";
+		regulator-name = "USB_PWR_EN";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc_5v>;
+
+		gpio = <&gpio GPIOH_6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vddao_1v8: regulator-vddao_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	vddao_3v3: regulator-vddao_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&main_12v>;
+		regulator-always-on;
+	};
+
+};
+
+&cec_AO {
+	pinctrl-0 = <&cec_ao_a_h_pins>;
+	pinctrl-names = "default";
+	status = "disabled";
+	hdmi-phandle = <&hdmi_tx>;
+};
+
+&cecb_AO {
+	pinctrl-0 = <&cec_ao_b_h_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+	hdmi-phandle = <&hdmi_tx>;
+};
+
+&cvbs_vdac_port {
+	cvbs_vdac_out: endpoint {
+		remote-endpoint = <&cvbs_connector_in>;
+	};
+};
+
+&hdmi_tx {
+	status = "okay";
+	pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
+	pinctrl-names = "default";
+	hdmi-supply = <&vcc_5v>;
+};
+
+&hdmi_tx_tmds_port {
+	hdmi_tx_tmds_out: endpoint {
+		remote-endpoint = <&hdmi_connector_in>;
+	};
 };
 
 &uart_AO {
 	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
 };
 
+&usb {
+	status = "okay";
+	vbus-supply = <&usb_pwr_en>;
+};
+
+&usb2_phy0 {
+	phy-supply = <&vcc_5v>;
+};
+
+&usb2_phy1 {
+	phy-supply = <&vcc_5v>;
+};

arch/arm/dts/meson-g12a.dtsi

@@ -3,9 +3,13 @@
  * Copyright (c) 2018 Amlogic, Inc. All rights reserved.
  */
 
+#include <dt-bindings/phy/phy.h>
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/g12a-clkc.h>
+#include <dt-bindings/clock/g12a-aoclkc.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/reset/amlogic,meson-g12a-reset.h>
 
 / {
 	compatible = "amlogic,g12a";
@@ -55,6 +59,14 @@
 		};
 	};
 
+	efuse: efuse {
+		compatible = "amlogic,meson-gxbb-efuse";
+		clocks = <&clkc CLKID_EFUSE>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		read-only;
+	};
+
 	psci {
 		compatible = "arm,psci-1.0";
 		method = "smc";
@@ -70,6 +82,18 @@
 			reg = <0x0 0x05000000 0x0 0x300000>;
 			no-map;
 		};
+
+		linux,cma {
+			compatible = "shared-dma-pool";
+			reusable;
+			size = <0x0 0x10000000>;
+			alignment = <0x0 0x400000>;
+			linux,cma-default;
+		};
+	};
+
+	sm: secure-monitor {
+		compatible = "amlogic,meson-gxbb-sm";
 	};
 
 	soc {
@@ -85,12 +109,177 @@
 			#size-cells = <2>;
 			ranges = <0x0 0x0 0x0 0xff600000 0x0 0x200000>;
 
+			hdmi_tx: hdmi-tx@0 {
+				compatible = "amlogic,meson-g12a-dw-hdmi";
+				reg = <0x0 0x0 0x0 0x10000>;
+				interrupts = <GIC_SPI 57 IRQ_TYPE_EDGE_RISING>;
+				resets = <&reset RESET_HDMITX_CAPB3>,
+					 <&reset RESET_HDMITX_PHY>,
+					 <&reset RESET_HDMITX>;
+				reset-names = "hdmitx_apb", "hdmitx", "hdmitx_phy";
+				clocks = <&clkc CLKID_HDMI>,
+					 <&clkc CLKID_HTX_PCLK>,
+					 <&clkc CLKID_VPU_INTR>;
+				clock-names = "isfr", "iahb", "venci";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+
+				/* VPU VENC Input */
+				hdmi_tx_venc_port: port@0 {
+					reg = <0>;
+
+					hdmi_tx_in: endpoint {
+						remote-endpoint = <&hdmi_tx_out>;
+					};
+				};
+
+				/* TMDS Output */
+				hdmi_tx_tmds_port: port@1 {
+					reg = <1>;
+				};
+			};
+
 			periphs: bus@34400 {
 				compatible = "simple-bus";
 				reg = <0x0 0x34400 0x0 0x400>;
 				#address-cells = <2>;
 				#size-cells = <2>;
 				ranges = <0x0 0x0 0x0 0x34400 0x0 0x400>;
+
+				periphs_pinctrl: pinctrl@40 {
+					compatible = "amlogic,meson-g12a-periphs-pinctrl";
+					#address-cells = <2>;
+					#size-cells = <2>;
+					ranges;
+
+					gpio: bank@40 {
+						reg = <0x0 0x40  0x0 0x4c>,
+						      <0x0 0xe8  0x0 0x18>,
+						      <0x0 0x120 0x0 0x18>,
+						      <0x0 0x2c0 0x0 0x40>,
+						      <0x0 0x340 0x0 0x1c>;
+						reg-names = "gpio",
+							    "pull",
+							    "pull-enable",
+							    "mux",
+							    "ds";
+						gpio-controller;
+						#gpio-cells = <2>;
+						gpio-ranges = <&periphs_pinctrl 0 0 86>;
+					};
+
+					cec_ao_a_h_pins: cec_ao_a_h {
+						mux {
+							groups = "cec_ao_a_h";
+							function = "cec_ao_a_h";
+							bias-disable;
+						};
+					};
+
+					cec_ao_b_h_pins: cec_ao_b_h {
+						mux {
+							groups = "cec_ao_b_h";
+							function = "cec_ao_b_h";
+							bias-disable;
+						};
+					};
+
+					hdmitx_ddc_pins: hdmitx_ddc {
+						mux {
+							groups = "hdmitx_sda",
+								 "hdmitx_sck";
+							function = "hdmitx";
+							bias-disable;
+						};
+					};
+
+					hdmitx_hpd_pins: hdmitx_hpd {
+						mux {
+							groups = "hdmitx_hpd_in";
+							function = "hdmitx";
+							bias-disable;
+						};
+					};
+
+					uart_a_pins: uart-a {
+						mux {
+							groups = "uart_a_tx",
+								 "uart_a_rx";
+							function = "uart_a";
+							bias-disable;
+						};
+					};
+
+					uart_a_cts_rts_pins: uart-a-cts-rts {
+						mux {
+							groups = "uart_a_cts",
+								 "uart_a_rts";
+							function = "uart_a";
+							bias-disable;
+						};
+					};
+
+					uart_b_pins: uart-b {
+						mux {
+							groups = "uart_b_tx",
+								 "uart_b_rx";
+							function = "uart_b";
+							bias-disable;
+						};
+					};
+
+					uart_c_pins: uart-c {
+						mux {
+							groups = "uart_c_tx",
+								 "uart_c_rx";
+							function = "uart_c";
+							bias-disable;
+						};
+					};
+
+					uart_c_cts_rts_pins: uart-c-cts-rts {
+						mux {
+							groups = "uart_c_cts",
+								 "uart_c_rts";
+							function = "uart_c";
+							bias-disable;
+						};
+					};
+				};
+			};
+
+			usb2_phy0: phy@36000 {
+				compatible = "amlogic,g12a-usb2-phy";
+				reg = <0x0 0x36000 0x0 0x2000>;
+				clocks = <&xtal>;
+				clock-names = "xtal";
+				resets = <&reset RESET_USB_PHY20>;
+				reset-names = "phy";
+				#phy-cells = <0>;
+			};
+
+			dmc: bus@38000 {
+				compatible = "simple-bus";
+				reg = <0x0 0x38000 0x0 0x400>;
+				#address-cells = <2>;
+				#size-cells = <2>;
+				ranges = <0x0 0x0 0x0 0x38000 0x0 0x400>;
+
+				canvas: video-lut@48 {
+					compatible = "amlogic,canvas";
+					reg = <0x0 0x48 0x0 0x14>;
+				};
+			};
+
+			usb2_phy1: phy@3a000 {
+				compatible = "amlogic,g12a-usb2-phy";
+				reg = <0x0 0x3a000 0x0 0x2000>;
+				clocks = <&xtal>;
+				clock-names = "xtal";
+				resets = <&reset RESET_USB_PHY21>;
+				reset-names = "phy";
+				#phy-cells = <0>;
 			};
 
 			hiu: bus@3c000 {
@@ -113,6 +302,18 @@
 					};
 				};
 			};
+
+			usb3_pcie_phy: phy@46000 {
+				compatible = "amlogic,g12a-usb3-pcie-phy";
+				reg = <0x0 0x46000 0x0 0x2000>;
+				clocks = <&clkc CLKID_PCIE_PLL>;
+				clock-names = "ref_clk";
+				resets = <&reset RESET_PCIE_PHY>;
+				reset-names = "phy";
+				assigned-clocks = <&clkc CLKID_PCIE_PLL>;
+				assigned-clock-rates = <100000000>;
+				#phy-cells = <1>;
+			};
 		};
 
 		aobus: bus@ff800000 {
@@ -122,6 +323,128 @@
 			#size-cells = <2>;
 			ranges = <0x0 0x0 0x0 0xff800000 0x0 0x100000>;
 
+			rti: sys-ctrl@0 {
+				compatible = "amlogic,meson-gx-ao-sysctrl",
+					     "simple-mfd", "syscon";
+				reg = <0x0 0x0 0x0 0x100>;
+				#address-cells = <2>;
+				#size-cells = <2>;
+				ranges = <0x0 0x0 0x0 0x0 0x0 0x100>;
+
+				clkc_AO: clock-controller {
+					compatible = "amlogic,meson-g12a-aoclkc";
+					#clock-cells = <1>;
+					#reset-cells = <1>;
+					clocks = <&xtal>, <&clkc CLKID_CLK81>;
+					clock-names = "xtal", "mpeg-clk";
+				};
+
+				pwrc_vpu: power-controller-vpu {
+					compatible = "amlogic,meson-g12a-pwrc-vpu";
+					#power-domain-cells = <0>;
+					amlogic,hhi-sysctrl = <&hhi>;
+					resets = <&reset RESET_VIU>,
+						 <&reset RESET_VENC>,
+						 <&reset RESET_VCBUS>,
+						 <&reset RESET_BT656>,
+						 <&reset RESET_RDMA>,
+						 <&reset RESET_VENCI>,
+						 <&reset RESET_VENCP>,
+						 <&reset RESET_VDAC>,
+						 <&reset RESET_VDI6>,
+						 <&reset RESET_VENCL>,
+						 <&reset RESET_VID_LOCK>;
+					clocks = <&clkc CLKID_VPU>,
+						 <&clkc CLKID_VAPB>;
+					clock-names = "vpu", "vapb";
+					/*
+					 * VPU clocking is provided by two identical clock paths
+					 * VPU_0 and VPU_1 muxed to a single clock by a glitch
+					 * free mux to safely change frequency while running.
+					 * Same for VAPB but with a final gate after the glitch free mux.
+					 */
+					assigned-clocks = <&clkc CLKID_VPU_0_SEL>,
+							  <&clkc CLKID_VPU_0>,
+							  <&clkc CLKID_VPU>, /* Glitch free mux */
+							  <&clkc CLKID_VAPB_0_SEL>,
+							  <&clkc CLKID_VAPB_0>,
+							  <&clkc CLKID_VAPB_SEL>; /* Glitch free mux */
+					assigned-clock-parents = <&clkc CLKID_FCLK_DIV3>,
+								 <0>, /* Do Nothing */
+								 <&clkc CLKID_VPU_0>,
+								 <&clkc CLKID_FCLK_DIV4>,
+								 <0>, /* Do Nothing */
+								 <&clkc CLKID_VAPB_0>;
+					assigned-clock-rates = <0>, /* Do Nothing */
+							       <666666666>,
+							       <0>, /* Do Nothing */
+							       <0>, /* Do Nothing */
+							       <250000000>,
+							       <0>; /* Do Nothing */
+				};
+
+				ao_pinctrl: pinctrl@14 {
+					compatible = "amlogic,meson-g12a-aobus-pinctrl";
+					#address-cells = <2>;
+					#size-cells = <2>;
+					ranges;
+
+					gpio_ao: bank@14 {
+						reg = <0x0 0x14 0x0 0x8>,
+						      <0x0 0x1c 0x0 0x8>,
+						      <0x0 0x24 0x0 0x14>;
+						reg-names = "mux",
+							    "ds",
+							    "gpio";
+						gpio-controller;
+						#gpio-cells = <2>;
+						gpio-ranges = <&ao_pinctrl 0 0 15>;
+					};
+
+					uart_ao_a_pins: uart-a-ao {
+						mux {
+							groups = "uart_ao_a_tx",
+								 "uart_ao_a_rx";
+							function = "uart_ao_a";
+							bias-disable;
+						};
+					};
+
+					uart_ao_a_cts_rts_pins: uart-ao-a-cts-rts {
+						mux {
+							groups = "uart_ao_a_cts",
+								 "uart_ao_a_rts";
+							function = "uart_ao_a";
+							bias-disable;
+						};
+					};
+				};
+			};
+
+			cec_AO: cec@100 {
+				compatible = "amlogic,meson-gx-ao-cec";
+				reg = <0x0 0x00100 0x0 0x14>;
+				interrupts = <GIC_SPI 199 IRQ_TYPE_EDGE_RISING>;
+				clocks = <&clkc_AO CLKID_AO_CEC>;
+				clock-names = "core";
+				status = "disabled";
+			};
+
+			sec_AO: ao-secure@140 {
+				compatible = "amlogic,meson-gx-ao-secure", "syscon";
+				reg = <0x0 0x140 0x0 0x140>;
+				amlogic,has-chip-id;
+			};
+
+			cecb_AO: cec@280 {
+				compatible = "amlogic,meson-g12a-ao-cec";
+				reg = <0x0 0x00280 0x0 0x1c>;
+				interrupts = <GIC_SPI 203 IRQ_TYPE_EDGE_RISING>;
+				clocks = <&clkc_AO CLKID_AO_CTS_OSCIN>;
+				clock-names = "oscin";
+				status = "disabled";
+			};
+
 			uart_AO: serial@3000 {
 				compatible = "amlogic,meson-gx-uart",
 					     "amlogic,meson-ao-uart";
@@ -141,6 +464,46 @@
 				clock-names = "xtal", "pclk", "baud";
 				status = "disabled";
 			};
+
+			saradc: adc@9000 {
+				compatible = "amlogic,meson-g12a-saradc",
+					     "amlogic,meson-saradc";
+				reg = <0x0 0x9000 0x0 0x48>;
+				#io-channel-cells = <1>;
+				interrupts = <GIC_SPI 200 IRQ_TYPE_EDGE_RISING>;
+				clocks = <&xtal>,
+					 <&clkc_AO CLKID_AO_SAR_ADC>,
+					 <&clkc_AO CLKID_AO_SAR_ADC_CLK>,
+					 <&clkc_AO CLKID_AO_SAR_ADC_SEL>;
+				clock-names = "clkin", "core", "adc_clk", "adc_sel";
+				status = "disabled";
+			};
+		};
+
+		vpu: vpu@ff900000 {
+			compatible = "amlogic,meson-g12a-vpu";
+			reg = <0x0 0xff900000 0x0 0x100000>,
+			      <0x0 0xff63c000 0x0 0x1000>;
+			reg-names = "vpu", "hhi";
+			interrupts = <GIC_SPI 3 IRQ_TYPE_EDGE_RISING>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			amlogic,canvas = <&canvas>;
+			power-domains = <&pwrc_vpu>;
+
+			/* CVBS VDAC output port */
+			cvbs_vdac_port: port@0 {
+				reg = <0>;
+			};
+
+			/* HDMI-TX output port */
+			hdmi_tx_port: port@1 {
+				reg = <1>;
+
+				hdmi_tx_out: endpoint {
+					remote-endpoint = <&hdmi_tx_in>;
+				};
+			};
 		};
 
 		gic: interrupt-controller@ffc01000 {
@@ -163,10 +526,112 @@
 			#size-cells = <2>;
 			ranges = <0x0 0x0 0x0 0xffd00000 0x0 0x100000>;
 
+			reset: reset-controller@1004 {
+				compatible = "amlogic,meson-g12a-reset",
+					     "amlogic,meson-axg-reset";
+				reg = <0x0 0x1004 0x0 0x9c>;
+				#reset-cells = <1>;
+			};
+
 			clk_msr: clock-measure@18000 {
 				compatible = "amlogic,meson-g12a-clk-measure";
 				reg = <0x0 0x18000 0x0 0x10>;
 			};
+
+			uart_C: serial@22000 {
+				compatible = "amlogic,meson-gx-uart";
+				reg = <0x0 0x22000 0x0 0x18>;
+				interrupts = <GIC_SPI 93 IRQ_TYPE_EDGE_RISING>;
+				clocks = <&xtal>, <&clkc CLKID_UART2>, <&xtal>;
+				clock-names = "xtal", "pclk", "baud";
+				status = "disabled";
+			};
+
+			uart_B: serial@23000 {
+				compatible = "amlogic,meson-gx-uart";
+				reg = <0x0 0x23000 0x0 0x18>;
+				interrupts = <GIC_SPI 75 IRQ_TYPE_EDGE_RISING>;
+				clocks = <&xtal>, <&clkc CLKID_UART1>, <&xtal>;
+				clock-names = "xtal", "pclk", "baud";
+				status = "disabled";
+			};
+
+			uart_A: serial@24000 {
+				compatible = "amlogic,meson-gx-uart";
+				reg = <0x0 0x24000 0x0 0x18>;
+				interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>;
+				clocks = <&xtal>, <&clkc CLKID_UART0>, <&xtal>;
+				clock-names = "xtal", "pclk", "baud";
+				status = "disabled";
+			};
+		};
+
+		usb: usb@ffe09000 {
+			status = "disabled";
+			compatible = "amlogic,meson-g12a-usb-ctrl";
+			reg = <0x0 0xffe09000 0x0 0xa0>;
+			interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			clocks = <&clkc CLKID_USB>;
+			resets = <&reset RESET_USB>;
+
+			dr_mode = "otg";
+
+			phys = <&usb2_phy0>, <&usb2_phy1>,
+			       <&usb3_pcie_phy PHY_TYPE_USB3>;
+			phy-names = "usb2-phy0", "usb2-phy1", "usb3-phy0";
+
+			dwc2: usb@ff400000 {
+				compatible = "amlogic,meson-g12a-usb", "snps,dwc2";
+				reg = <0x0 0xff400000 0x0 0x40000>;
+				interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clkc CLKID_USB1_DDR_BRIDGE>;
+				clock-names = "ddr";
+				phys = <&usb2_phy1>;
+				dr_mode = "peripheral";
+				g-rx-fifo-size = <192>;
+				g-np-tx-fifo-size = <128>;
+				g-tx-fifo-size = <128 128 16 16 16>;
+			};
+
+			dwc3: usb@ff500000 {
+				compatible = "snps,dwc3";
+				reg = <0x0 0xff500000 0x0 0x100000>;
+				interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+				dr_mode = "host";
+				snps,dis_u2_susphy_quirk;
+				snps,quirk-frame-length-adjustment;
+			};
+		};
+
+		mali: gpu@ffe40000 {
+			compatible = "amlogic,meson-g12a-mali", "arm,mali-bifrost";
+			reg = <0x0 0xffe40000 0x0 0x40000>;
+			interrupt-parent = <&gic>;
+			interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "gpu", "mmu", "job";
+			clocks = <&clkc CLKID_MALI>;
+			resets = <&reset RESET_DVALIN_CAPB3>, <&reset RESET_DVALIN>;
+
+			/*
+			 * Mali clocking is provided by two identical clock paths
+			 * MALI_0 and MALI_1 muxed to a single clock by a glitch
+			 * free mux to safely change frequency while running.
+			 */
+			assigned-clocks = <&clkc CLKID_MALI_0_SEL>,
+					  <&clkc CLKID_MALI_0>,
+					  <&clkc CLKID_MALI>; /* Glitch free mux */
+			assigned-clock-parents = <&clkc CLKID_FCLK_DIV2P5>,
+						 <0>, /* Do Nothing */
+						 <&clkc CLKID_MALI_0>;
+			assigned-clock-rates = <0>, /* Do Nothing */
+					       <800000000>,
+					       <0>; /* Do Nothing */
 		};
 	};
 

arch/arm/dts/pcl063-common.dtsi

@@ -7,10 +7,6 @@
  * Author: Christian Hemp <c.hemp@phytec.de>
  */
 
-/dts-v1/;
-
-#include "imx6ul.dtsi"
-
 / {
 	model = "Phytec phyCORE-i.MX6 Ultra Lite SOM";
 	compatible = "phytec,imx6ul-pcl063", "fsl,imx6ul";
@@ -47,7 +43,7 @@
 	pinctrl-0 = <&pinctrl_gpmi_nand>;
 	nand-on-flash-bbt;
 	fsl,no-blockmark-swap;
-	status = "okay";
+	status = "disabled";
 
 	#address-cells = <1>;
 	#size-cells = <1>;
@@ -99,6 +95,18 @@
 	status = "okay";
 };
 
+&usdhc2 {
+	u-boot,dm-spl;
+	u-boot,dm-pre-reloc;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	bus-width = <8>;
+	no-1-8-v;
+	non-removable;
+	keep-power-in-suspend;
+	status = "disabled";
+};
+
 &iomuxc {
 	pinctrl-names = "default";
 
@@ -170,4 +178,19 @@
 
 		>;
 	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x170f9
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x100f9
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x170f9
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x170f9
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x170f9
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x170f9
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x170f9
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x170f9
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x170f9
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x170f9
+		>;
+	};
 };

arch/arm/dts/rk3288-tinker-u-boot.dtsi

@@ -0,0 +1,54 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2019 Rockchip Electronics Co., Ltd
+ */
+
+#include "rk3288-u-boot.dtsi"
+
+&pinctrl {
+	u-boot,dm-pre-reloc;
+};
+
+&uart2 {
+	u-boot,dm-pre-reloc;
+};
+
+&sdmmc {
+	u-boot,dm-pre-reloc;
+};
+
+&emmc {
+	u-boot,dm-pre-reloc;
+};
+
+&gpio3 {
+	u-boot,dm-pre-reloc;
+};
+
+&gpio8 {
+	u-boot,dm-pre-reloc;
+};
+
+&pcfg_pull_none_drv_8ma {
+	u-boot,dm-spl;
+};
+
+&pcfg_pull_up_drv_8ma {
+	u-boot,dm-spl;
+};
+
+&sdmmc_bus4 {
+	u-boot,dm-spl;
+};
+
+&sdmmc_clk {
+	u-boot,dm-spl;
+};
+
+&sdmmc_cmd {
+	u-boot,dm-spl;
+};
+
+&sdmmc_pwr {
+	u-boot,dm-spl;
+};

arch/arm/dts/rk3288-tinker.dts

@@ -28,8 +28,6 @@
 
 
 &pinctrl {
-	u-boot,dm-pre-reloc;
-
 	usb {
 		host_vbus_drv: host-vbus-drv {
 			rockchip,pins = <0 14 RK_FUNC_GPIO &pcfg_pull_none>;
@@ -42,7 +40,6 @@
 };
 
 &uart2 {
-	u-boot,dm-pre-reloc;
 	reg-shift = <2>;
 };
 
@@ -51,22 +48,6 @@
 	status = "okay";
 };
 
-&sdmmc {
-	u-boot,dm-pre-reloc;
-};
-
-&emmc {
-	u-boot,dm-pre-reloc;
-};
-
-&gpio3 {
-	u-boot,dm-pre-reloc;
-};
-
-&gpio8 {
-	u-boot,dm-pre-reloc;
-};
-
 &i2c2 {
     m24c08@50 {
         compatible = "at,24c08", "i2c-eeprom";

arch/arm/dts/rk3288-u-boot.dtsi

@@ -0,0 +1,36 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2019 Rockchip Electronics Co., Ltd
+ */
+
+&dmc {
+	u-boot,dm-pre-reloc;
+};
+
+&pmu {
+	u-boot,dm-pre-reloc;
+};
+
+&sgrf {
+	u-boot,dm-pre-reloc;
+};
+
+&cru {
+	u-boot,dm-pre-reloc;
+};
+
+&grf {
+	u-boot,dm-pre-reloc;
+};
+
+&vopb {
+	u-boot,dm-pre-reloc;
+};
+
+&vopl {
+	u-boot,dm-pre-reloc;
+};
+
+&noc {
+	u-boot,dm-pre-reloc;
+};

arch/arm/dts/rk3288-veyron-speedy-u-boot.dtsi

@@ -3,6 +3,8 @@
  * Copyright 2015 Google, Inc
  */
 
+#include "rk3288-u-boot.dtsi"
+
 &dmc {
 	rockchip,pctl-timing = <0x215 0xc8 0x0 0x35 0x26 0x2 0x70 0x2000d
 		0x6 0x0 0x8 0x4 0x17 0x24 0xd 0x6

arch/arm/dts/rk3288-vyasa-u-boot.dtsi

@@ -3,6 +3,8 @@
  * Copyright (C) 2017 Jagan Teki <jagan@amarulasolutions.com>
  */
 
+#include "rk3288-u-boot.dtsi"
+
 &dmc {
 	rockchip,pctl-timing = <0x29a 0xc8 0x1f8 0x42 0x4e 0x4 0xea 0xa
 		0x5 0x0 0xa 0x7 0x19 0x24 0xa 0x7

arch/arm/dts/rk3288.dtsi

@@ -468,7 +468,6 @@
 	};
 
 	dmc: dmc@ff610000 {
-		u-boot,dm-pre-reloc;
 		compatible = "rockchip,rk3288-dmc", "syscon";
 		rockchip,cru = <&cru>;
 		rockchip,grf = <&grf>;
@@ -584,13 +583,11 @@
 	};
 
 	pmu: power-management@ff730000 {
-		u-boot,dm-pre-reloc;
 		compatible = "rockchip,rk3288-pmu", "syscon";
 		reg = <0xff730000 0x100>;
 	};
 
 	sgrf: syscon@ff740000 {
-		u-boot,dm-pre-reloc;
 		compatible = "rockchip,rk3288-sgrf", "syscon";
 		reg = <0xff740000 0x1000>;
 	};
@@ -599,7 +596,6 @@
 		compatible = "rockchip,rk3288-cru";
 		reg = <0xff760000 0x1000>;
 		rockchip,grf = <&grf>;
-		u-boot,dm-pre-reloc;
 		#clock-cells = <1>;
 		#reset-cells = <1>;
 		assigned-clocks = <&cru PLL_GPLL>, <&cru PLL_CPLL>,
@@ -615,7 +611,6 @@
 	};
 
 	grf: syscon@ff770000 {
-		u-boot,dm-pre-reloc;
 		compatible = "rockchip,rk3288-grf", "syscon";
 		reg = <0xff770000 0x1000>;
 	};
@@ -660,7 +655,6 @@
 	};
 
 	vopb: vop@ff930000 {
-		u-boot,dm-pre-reloc;
 		compatible = "rockchip,rk3288-vop";
 		reg = <0xff930000 0x19c>;
 		interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
@@ -715,7 +709,6 @@
 		iommus = <&vopl_mmu>;
 		power-domains = <&power RK3288_PD_VIO>;
 		status = "disabled";
-		u-boot,dm-pre-reloc;
 		vopl_out: port {
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -911,7 +904,6 @@
 	};
 
 	noc: syscon@ffac0000 {
-		u-boot,dm-pre-reloc;
 		compatible = "rockchip,rk3288-noc", "syscon";
 		reg = <0xffac0000 0x2000>;
 	};

arch/arm/dts/rk3328-rock64-u-boot.dtsi

@@ -0,0 +1,34 @@
+/*
+ * (C) Copyright 2018 Rockchip Electronics Co., Ltd
+ *
+ * SPDX-License-Identifier:     GPL-2.0+
+ */
+
+/ {
+	aliases {
+		mmc0 = &emmc;
+		mmc1 = &sdmmc;
+	};
+
+	chosen {
+		u-boot,spl-boot-order = &emmc, &sdmmc;
+	};
+};
+
+&cru {
+	u-boot,dm-pre-reloc;
+};
+
+&uart2 {
+	u-boot,dm-pre-reloc;
+};
+
+&emmc {
+	u-boot,dm-pre-reloc;
+	fifo-mode;
+};
+
+&sdmmc {
+	u-boot,dm-pre-reloc;
+	fifo-mode;
+};

arch/arm/dts/rk3328-rock64.dts

@@ -0,0 +1,294 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2017 PINE64
+ */
+
+/dts-v1/;
+#include "rk3328.dtsi"
+
+/ {
+	model = "Pine64 Rock64";
+	compatible = "pine64,rock64", "rockchip,rk3328";
+
+	chosen {
+		stdout-path = "serial2:1500000n8";
+	};
+
+	gmac_clkin: external-gmac-clock {
+		compatible = "fixed-clock";
+		clock-frequency = <125000000>;
+		clock-output-names = "gmac_clkin";
+		#clock-cells = <0>;
+	};
+
+	vcc_sd: sdmmc-regulator {
+		compatible = "regulator-fixed";
+		gpio = <&gpio0 RK_PD6 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&sdmmc0m1_gpio>;
+		regulator-name = "vcc_sd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_io>;
+	};
+
+	vcc_host_5v: vcc-host-5v-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 RK_PA0 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb30_host_drv>;
+		regulator-name = "vcc_host_5v";
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vcc_sys>;
+	};
+
+	vcc_host1_5v: vcc_otg_5v: vcc-host1-5v-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 RK_PA2 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb20_host_drv>;
+		regulator-name = "vcc_host1_5v";
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vcc_sys>;
+	};
+
+	vcc_sys: vcc-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&vdd_arm>;
+};
+
+&cpu1 {
+	cpu-supply = <&vdd_arm>;
+};
+
+&cpu2 {
+	cpu-supply = <&vdd_arm>;
+};
+
+&cpu3 {
+	cpu-supply = <&vdd_arm>;
+};
+
+&emmc {
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	mmc-hs200-1_8v;
+	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>;
+	vmmc-supply = <&vcc_io>;
+	vqmmc-supply = <&vcc18_emmc>;
+	status = "okay";
+};
+
+&gmac2io {
+	assigned-clocks = <&cru SCLK_MAC2IO>, <&cru SCLK_MAC2IO_EXT>;
+	assigned-clock-parents = <&gmac_clkin>, <&gmac_clkin>;
+	clock_in_out = "input";
+	phy-supply = <&vcc_io>;
+	phy-mode = "rgmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmiim1_pins>;
+	snps,force_thresh_dma_mode;
+	snps,reset-gpio = <&gpio1 RK_PC2 GPIO_ACTIVE_LOW>;
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 10000 50000>;
+	tx_delay = <0x24>;
+	rx_delay = <0x18>;
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+
+	rk805: rk805@18 {
+		compatible = "rockchip,rk805";
+		reg = <0x18>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
+		#clock-cells = <1>;
+		clock-output-names = "xin32k", "rk805-clkout2";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int_l>;
+		rockchip,system-power-controller;
+		wakeup-source;
+
+		vcc1-supply = <&vcc_sys>;
+		vcc2-supply = <&vcc_sys>;
+		vcc3-supply = <&vcc_sys>;
+		vcc4-supply = <&vcc_sys>;
+		vcc5-supply = <&vcc_io>;
+		vcc6-supply = <&vcc_sys>;
+
+		regulators {
+			vdd_logic: DCDC_REG1 {
+				regulator-name = "vdd_logic";
+				regulator-min-microvolt = <712500>;
+				regulator-max-microvolt = <1450000>;
+				regulator-ramp-delay = <12500>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1000000>;
+				};
+			};
+
+			vdd_arm: DCDC_REG2 {
+				regulator-name = "vdd_arm";
+				regulator-min-microvolt = <712500>;
+				regulator-max-microvolt = <1450000>;
+				regulator-ramp-delay = <12500>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <950000>;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-name = "vcc_ddr";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_io: DCDC_REG4 {
+				regulator-name = "vcc_io";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcc_18: LDO_REG1 {
+				regulator-name = "vdd_18";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcc18_emmc: LDO_REG2 {
+				regulator-name = "vcc_18emmc";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vdd_10: LDO_REG3 {
+				regulator-name = "vdd_10";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1000000>;
+				};
+			};
+		};
+	};
+};
+
+&io_domains {
+	status = "okay";
+
+	vccio1-supply = <&vcc_io>;
+	vccio2-supply = <&vcc18_emmc>;
+	vccio3-supply = <&vcc_io>;
+	vccio4-supply = <&vcc_18>;
+	vccio5-supply = <&vcc_io>;
+	vccio6-supply = <&vcc_io>;
+	pmuio-supply = <&vcc_io>;
+};
+
+&pinctrl {
+	pmic {
+		pmic_int_l: pmic-int-l {
+			rockchip,pins = <2 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	usb2 {
+		usb20_host_drv: usb20-host-drv {
+			rockchip,pins = <0 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	usb3 {
+		usb30_host_drv: usb30-host-drv {
+			rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-mmc-highspeed;
+	cap-sd-highspeed;
+	disable-wp;
+	max-frequency = <150000000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc0_clk &sdmmc0_cmd &sdmmc0_dectn &sdmmc0_bus4>;
+	vmmc-supply = <&vcc_sd>;
+	status = "okay";
+};
+
+&spi0 {
+	status = "okay";
+
+	spiflash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+
+		/* maximum speed for Rockchip SPI */
+		spi-max-frequency = <50000000>;
+	};
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&usb20_otg {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&usb_host0_ohci {
+	status = "okay";
+};

arch/arm/dts/rk3399-gru.dtsi

@@ -629,7 +629,6 @@ ap_i2c_audio: &i2c8 {
 
 &uart2 {
 	status = "okay";
-	u-boot,dm-pre-reloc;
 };
 
 &usb_host0_ohci {

arch/arm/dts/rk3399-nanopi-neo4-u-boot.dtsi

@@ -0,0 +1,6 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2019 Jagan Teki <jagan@amarulasolutions.com>
+ */
+
+#include "rk3399-nanopi4-u-boot.dtsi"

arch/arm/dts/rk3399-nanopi-neo4.dts

@@ -0,0 +1,50 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2019 Amarula Solutions B.V.
+ * Author: Jagan Teki <jagan@amarulasolutions.com>
+ */
+
+/dts-v1/;
+
+#include "rk3399-nanopi4.dtsi"
+
+/ {
+	model = "FriendlyARM NanoPi NEO4";
+	compatible = "friendlyarm,nanopi-neo4", "rockchip,rk3399";
+
+	vdd_5v: vdd-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_5v";
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vcc5v0_core: vcc5v0-core {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_core";
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vdd_5v>;
+	};
+
+	vcc5v0_usb1: vcc5v0-usb1 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_usb1";
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vcc5v0_sys>;
+	};
+};
+
+&vcc3v3_sys {
+	vin-supply = <&vcc5v0_core>;
+};
+
+&u2phy0_host {
+	phy-supply = <&vcc5v0_usb1>;
+};
+
+&vbus_typec {
+	regulator-always-on;
+	vin-supply = <&vdd_5v>;
+};

arch/arm/dts/rk3399-puma.dtsi

@@ -639,7 +639,6 @@
 };
 
 &uart0 {
-	u-boot,dm-pre-reloc;
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_xfer &uart0_cts>;
 	status = "okay";

arch/arm/dts/rk3399-rock-pi-4-u-boot.dtsi

@@ -0,0 +1,6 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2019 Jagan Teki <jagan@amarulasolutions.com>
+ */
+
+#include "rk3399-u-boot.dtsi"

arch/arm/dts/rk3399-rock-pi-4.dts

@@ -0,0 +1,606 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 Akash Gajjar <Akash_Gajjar@mentor.com>
+ * Copyright (c) 2019 Pragnesh Patel <Pragnesh_Patel@mentor.com>
+ */
+
+/dts-v1/;
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/pwm/pwm.h>
+#include "rk3399.dtsi"
+#include "rk3399-opp.dtsi"
+
+/ {
+	model = "Radxa ROCK Pi 4";
+	compatible = "radxa,rockpi4", "rockchip,rk3399";
+
+	chosen {
+		stdout-path = "serial2:1500000n8";
+	};
+
+	clkin_gmac: external-gmac-clock {
+		compatible = "fixed-clock";
+		clock-frequency = <125000000>;
+		clock-output-names = "clkin_gmac";
+		#clock-cells = <0>;
+	};
+
+	vcc12v_dcin: dc-12v {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc12v_dcin";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+	};
+
+	vcc5v0_sys: vcc-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc12v_dcin>;
+	};
+
+	vcc3v3_pcie: vcc3v3-pcie-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio2 RK_PD2 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pcie_pwr_en>;
+		regulator-name = "vcc3v3_pcie";
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	vcc3v3_sys: vcc3v3-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	vcc5v0_host: vcc5v0-host-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio4 RK_PD1 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_host_en>;
+		regulator-name = "vcc5v0_host";
+		regulator-always-on;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	vcc5v0_typec: vcc5v0-typec-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio1 RK_PA3 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_typec_en>;
+		regulator-name = "vcc5v0_typec";
+		regulator-always-on;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	vcc_lan: vcc3v3-phy-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_lan";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+
+	vdd_log: vdd-log {
+		compatible = "pwm-regulator";
+		pwms = <&pwm2 0 25000 1>;
+		regulator-name = "vdd_log";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <800000>;
+		regulator-max-microvolt = <1400000>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+};
+
+&cpu_l0 {
+	cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l1 {
+	cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l2 {
+	cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l3 {
+	cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_b0 {
+	cpu-supply = <&vdd_cpu_b>;
+};
+
+&cpu_b1 {
+	cpu-supply = <&vdd_cpu_b>;
+};
+
+&emmc_phy {
+	status = "okay";
+};
+
+&gmac {
+	assigned-clocks = <&cru SCLK_RMII_SRC>;
+	assigned-clock-parents = <&clkin_gmac>;
+	clock_in_out = "input";
+	phy-supply = <&vcc_lan>;
+	phy-mode = "rgmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii_pins>;
+	snps,reset-gpio = <&gpio3 RK_PB7 GPIO_ACTIVE_LOW>;
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 10000 50000>;
+	tx_delay = <0x28>;
+	rx_delay = <0x11>;
+	status = "okay";
+};
+
+&hdmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hdmi_cec>;
+	status = "okay";
+};
+
+&i2c0 {
+	clock-frequency = <400000>;
+	i2c-scl-rising-time-ns = <168>;
+	i2c-scl-falling-time-ns = <4>;
+	status = "okay";
+
+	rk808: pmic@1b {
+		compatible = "rockchip,rk808";
+		reg = <0x1b>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
+		#clock-cells = <1>;
+		clock-output-names = "xin32k", "rk808-clkout2";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int_l>;
+		rockchip,system-power-controller;
+		wakeup-source;
+
+		vcc1-supply = <&vcc5v0_sys>;
+		vcc2-supply = <&vcc5v0_sys>;
+		vcc3-supply = <&vcc5v0_sys>;
+		vcc4-supply = <&vcc5v0_sys>;
+		vcc6-supply = <&vcc5v0_sys>;
+		vcc7-supply = <&vcc5v0_sys>;
+		vcc8-supply = <&vcc3v3_sys>;
+		vcc9-supply = <&vcc5v0_sys>;
+		vcc10-supply = <&vcc5v0_sys>;
+		vcc11-supply = <&vcc5v0_sys>;
+		vcc12-supply = <&vcc3v3_sys>;
+		vddio-supply = <&vcc_1v8>;
+
+		regulators {
+			vdd_center: DCDC_REG1 {
+				regulator-name = "vdd_center";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-ramp-delay = <6001>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_cpu_l: DCDC_REG2 {
+				regulator-name = "vdd_cpu_l";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-ramp-delay = <6001>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-name = "vcc_ddr";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_1v8: DCDC_REG4 {
+				regulator-name = "vcc_1v8";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcc1v8_codec: LDO_REG1 {
+				regulator-name = "vcc1v8_codec";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc1v8_hdmi: LDO_REG2 {
+				regulator-name = "vcc1v8_hdmi";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcca_1v8: LDO_REG3 {
+				regulator-name = "vcca_1v8";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcc_sdio: LDO_REG4 {
+				regulator-name = "vcc_sdio";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3000000>;
+				};
+			};
+
+			vcca3v0_codec: LDO_REG5 {
+				regulator-name = "vcca3v0_codec";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_1v5: LDO_REG6 {
+				regulator-name = "vcc_1v5";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1500000>;
+				};
+			};
+
+			vcc0v9_hdmi: LDO_REG7 {
+				regulator-name = "vcc0v9_hdmi";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_3v0: LDO_REG8 {
+				regulator-name = "vcc_3v0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3000000>;
+				};
+			};
+
+			vcc_cam: SWITCH_REG1 {
+				regulator-name = "vcc_cam";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_mipi: SWITCH_REG2 {
+				regulator-name = "vcc_mipi";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+		};
+	};
+
+	vdd_cpu_b: regulator@40 {
+		compatible = "silergy,syr827";
+		reg = <0x40>;
+		fcs,suspend-voltage-selector = <1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vsel1_gpio>;
+		regulator-name = "vdd_cpu_b";
+		regulator-min-microvolt = <712500>;
+		regulator-max-microvolt = <1500000>;
+		regulator-ramp-delay = <1000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vcc5v0_sys>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+
+	vdd_gpu: regulator@41 {
+		compatible = "silergy,syr828";
+		reg = <0x41>;
+		fcs,suspend-voltage-selector = <1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vsel2_gpio>;
+		regulator-name = "vdd_gpu";
+		regulator-min-microvolt = <712500>;
+		regulator-max-microvolt = <1500000>;
+		regulator-ramp-delay = <1000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vcc5v0_sys>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+};
+
+&i2c1 {
+	i2c-scl-rising-time-ns = <300>;
+	i2c-scl-falling-time-ns = <15>;
+	status = "okay";
+};
+
+&i2c3 {
+	i2c-scl-rising-time-ns = <450>;
+	i2c-scl-falling-time-ns = <15>;
+	status = "okay";
+};
+
+&i2c4 {
+	i2c-scl-rising-time-ns = <600>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+};
+
+&i2s0 {
+	rockchip,playback-channels = <8>;
+	rockchip,capture-channels = <8>;
+	status = "okay";
+};
+
+&i2s1 {
+	rockchip,playback-channels = <2>;
+	rockchip,capture-channels = <2>;
+	status = "okay";
+};
+
+&i2s2 {
+	status = "okay";
+};
+
+&io_domains {
+	status = "okay";
+
+	bt656-supply = <&vcc_3v0>;
+	audio-supply = <&vcc_3v0>;
+	sdmmc-supply = <&vcc_sdio>;
+	gpio1830-supply = <&vcc_3v0>;
+};
+
+&pmu_io_domains {
+	status = "okay";
+
+	pmu1830-supply = <&vcc_3v0>;
+};
+
+&pinctrl {
+	pcie {
+		pcie_pwr_en: pcie-pwr-en {
+			rockchip,pins = <2 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	pmic {
+		pmic_int_l: pmic-int-l {
+			rockchip,pins = <1 RK_PC5 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+
+		vsel1_gpio: vsel1-gpio {
+			rockchip,pins = <1 RK_PC1 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+
+		vsel2_gpio: vsel2-gpio {
+			rockchip,pins = <1 RK_PB6 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+	};
+
+	usb-typec {
+		vcc5v0_typec_en: vcc5v0-typec-en {
+			rockchip,pins = <1 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	usb2 {
+		vcc5v0_host_en: vcc5v0-host-en {
+			rockchip,pins = <4 RK_PD1 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&pwm2 {
+	status = "okay";
+};
+
+&saradc {
+	status = "okay";
+
+	vref-supply = <&vcc_1v8>;
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-mmc-highspeed;
+	cap-sd-highspeed;
+	cd-gpios = <&gpio0 RK_PA7 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	max-frequency = <150000000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc_clk &sdmmc_cd &sdmmc_cmd &sdmmc_bus4>;
+	status = "okay";
+};
+
+&sdhci {
+	bus-width = <8>;
+	mmc-hs400-1_8v;
+	mmc-hs400-enhanced-strobe;
+	non-removable;
+	status = "okay";
+};
+
+&tcphy0 {
+	status = "okay";
+};
+
+&tcphy1 {
+	status = "okay";
+};
+
+&tsadc {
+	status = "okay";
+
+	/* tshut mode 0:CRU 1:GPIO */
+	rockchip,hw-tshut-mode = <1>;
+	/* tshut polarity 0:LOW 1:HIGH */
+	rockchip,hw-tshut-polarity = <1>;
+};
+
+&u2phy0 {
+	status = "okay";
+
+	u2phy0_otg: otg-port {
+		status = "okay";
+	};
+
+	u2phy0_host: host-port {
+		phy-supply = <&vcc5v0_host>;
+		status = "okay";
+	};
+};
+
+&u2phy1 {
+	status = "okay";
+
+	u2phy1_otg: otg-port {
+		status = "okay";
+	};
+
+	u2phy1_host: host-port {
+		phy-supply = <&vcc5v0_host>;
+		status = "okay";
+	};
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&usb_host0_ohci {
+	status = "okay";
+};
+
+&usb_host1_ehci {
+	status = "okay";
+};
+
+&usb_host1_ohci {
+	status = "okay";
+};
+
+&usbdrd3_0 {
+	status = "okay";
+};
+
+&usbdrd_dwc3_0 {
+	status = "okay";
+	dr_mode = "otg";
+};
+
+&usbdrd3_1 {
+	status = "okay";
+};
+
+&usbdrd_dwc3_1 {
+	status = "okay";
+	dr_mode = "host";
+};
+
+&vopb {
+	status = "okay";
+};
+
+&vopb_mmu {
+	status = "okay";
+};
+
+&vopl {
+	status = "okay";
+};
+
+&vopl_mmu {
+	status = "okay";
+};

arch/arm/dts/rk3399-rockpro64-u-boot.dtsi

@@ -0,0 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2019 Jagan Teki <jagan@amarulasolutions.com>
+ */
+
+#include "rk3399-u-boot.dtsi"
+
+&vdd_log {
+	regulator-init-microvolt = <950000>;
+};

arch/arm/dts/rk3399-rockpro64.dts

@@ -0,0 +1,712 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2017 Fuzhou Rockchip Electronics Co., Ltd.
+ * Copyright (c) 2018 Akash Gajjar <Akash_Gajjar@mentor.com>
+ */
+
+/dts-v1/;
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/pwm/pwm.h>
+#include "rk3399.dtsi"
+#include "rk3399-opp.dtsi"
+
+/ {
+	model = "Pine64 RockPro64";
+	compatible = "pine64,rockpro64", "rockchip,rk3399";
+
+	chosen {
+		stdout-path = "serial2:1500000n8";
+	};
+
+	clkin_gmac: external-gmac-clock {
+		compatible = "fixed-clock";
+		clock-frequency = <125000000>;
+		clock-output-names = "clkin_gmac";
+		#clock-cells = <0>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pwrbtn>;
+
+		power {
+			debounce-interval = <100>;
+			gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
+			label = "GPIO Key Power";
+			linux,code = <KEY_POWER>;
+			wakeup-source;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&work_led_gpio>, <&diy_led_gpio>;
+
+		work-led {
+			label = "work";
+			default-state = "on";
+			gpios = <&gpio0 RK_PB3 GPIO_ACTIVE_HIGH>;
+		};
+
+		diy-led {
+			label = "diy";
+			default-state = "off";
+			gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&rk808 1>;
+		clock-names = "ext_clock";
+		pinctrl-names = "default";
+		pinctrl-0 = <&wifi_enable_h>;
+
+		/*
+		 * On the module itself this is one of these (depending
+		 * on the actual card populated):
+		 * - SDIO_RESET_L_WL_REG_ON
+		 * - PDN (power down when low)
+		 */
+		reset-gpios = <&gpio0 RK_PB2 GPIO_ACTIVE_LOW>;
+	};
+
+	vcc12v_dcin: vcc12v-dcin {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc12v_dcin";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+	};
+
+	/* switched by pmic_sleep */
+	vcc1v8_s3: vcca1v8_s3: vcc1v8-s3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc1v8_s3";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_1v8>;
+	};
+
+	vcc3v3_pcie: vcc3v3-pcie-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio1 RK_PD0 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pcie_pwr_en>;
+		regulator-name = "vcc3v3_pcie";
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vcc12v_dcin>;
+	};
+
+	vcc3v3_sys: vcc3v3-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	/* Actually 3 regulators (host0, 1, 2) controlled by the same gpio */
+	vcc5v0_host: vcc5v0-host-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio4 RK_PD2 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_host_en>;
+		regulator-name = "vcc5v0_host";
+		regulator-always-on;
+		vin-supply = <&vcc5v0_usb>;
+	};
+
+	vcc5v0_typec: vcc5v0-typec-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio1 RK_PA3 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_typec_en>;
+		regulator-name = "vcc5v0_typec";
+		regulator-always-on;
+		vin-supply = <&vcc5v0_usb>;
+	};
+
+	vcc5v0_sys: vcc5v0-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc12v_dcin>;
+	};
+
+	vcc5v0_usb: vcc5v0-usb {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_usb";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc12v_dcin>;
+	};
+
+	vdd_log: vdd-log {
+		compatible = "pwm-regulator";
+		pwms = <&pwm2 0 25000 1>;
+		regulator-name = "vdd_log";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <800000>;
+		regulator-max-microvolt = <1400000>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+};
+
+&cpu_l0 {
+	cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l1 {
+	cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l2 {
+	cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l3 {
+	cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_b0 {
+	cpu-supply = <&vdd_cpu_b>;
+};
+
+&cpu_b1 {
+	cpu-supply = <&vdd_cpu_b>;
+};
+
+&emmc_phy {
+	status = "okay";
+};
+
+&gmac {
+	assigned-clocks = <&cru SCLK_RMII_SRC>;
+	assigned-clock-parents = <&clkin_gmac>;
+	clock_in_out = "input";
+	phy-supply = <&vcc_lan>;
+	phy-mode = "rgmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii_pins>;
+	snps,reset-gpio = <&gpio3 RK_PB7 GPIO_ACTIVE_LOW>;
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 10000 50000>;
+	tx_delay = <0x28>;
+	rx_delay = <0x11>;
+	status = "okay";
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c3>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&hdmi_cec>;
+	status = "okay";
+};
+
+&gpu {
+	mali-supply = <&vdd_gpu>;
+	status = "okay";
+};
+
+&i2c0 {
+	clock-frequency = <400000>;
+	i2c-scl-rising-time-ns = <168>;
+	i2c-scl-falling-time-ns = <4>;
+	status = "okay";
+
+	rk808: pmic@1b {
+		compatible = "rockchip,rk808";
+		reg = <0x1b>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
+		#clock-cells = <1>;
+		clock-output-names = "xin32k", "rk808-clkout2";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int_l>;
+		rockchip,system-power-controller;
+		wakeup-source;
+
+		vcc1-supply = <&vcc5v0_sys>;
+		vcc2-supply = <&vcc5v0_sys>;
+		vcc3-supply = <&vcc5v0_sys>;
+		vcc4-supply = <&vcc5v0_sys>;
+		vcc6-supply = <&vcc5v0_sys>;
+		vcc7-supply = <&vcc5v0_sys>;
+		vcc8-supply = <&vcc3v3_sys>;
+		vcc9-supply = <&vcc5v0_sys>;
+		vcc10-supply = <&vcc5v0_sys>;
+		vcc11-supply = <&vcc5v0_sys>;
+		vcc12-supply = <&vcc3v3_sys>;
+		vddio-supply = <&vcca_1v8>;
+
+		regulators {
+			vdd_center: DCDC_REG1 {
+				regulator-name = "vdd_center";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-ramp-delay = <6001>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_cpu_l: DCDC_REG2 {
+				regulator-name = "vdd_cpu_l";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-ramp-delay = <6001>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-name = "vcc_ddr";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_1v8: DCDC_REG4 {
+				regulator-name = "vcc_1v8";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcc1v8_dvp: LDO_REG1 {
+				regulator-name = "vcc1v8_dvp";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc3v0_touch: LDO_REG2 {
+				regulator-name = "vcc3v0_touch";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcca_1v8: LDO_REG3 {
+				regulator-name = "vcca_1v8";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcc_sdio: LDO_REG4 {
+				regulator-name = "vcc_sdio";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3000000>;
+				};
+			};
+
+			vcca3v0_codec: LDO_REG5 {
+				regulator-name = "vcca3v0_codec";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_1v5: LDO_REG6 {
+				regulator-name = "vcc_1v5";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1500000>;
+				};
+			};
+
+			vcca1v8_codec: LDO_REG7 {
+				regulator-name = "vcca1v8_codec";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_3v0: LDO_REG8 {
+				regulator-name = "vcc_3v0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3000000>;
+				};
+			};
+
+			vcc3v3_s3: vcc_lan: SWITCH_REG1 {
+				regulator-name = "vcc3v3_s3";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc3v3_s0: SWITCH_REG2 {
+				regulator-name = "vcc3v3_s0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+		};
+	};
+
+	vdd_cpu_b: regulator@40 {
+		compatible = "silergy,syr827";
+		reg = <0x40>;
+		fcs,suspend-voltage-selector = <1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vsel1_gpio>;
+		regulator-name = "vdd_cpu_b";
+		regulator-min-microvolt = <712500>;
+		regulator-max-microvolt = <1500000>;
+		regulator-ramp-delay = <1000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vcc5v0_sys>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+
+	vdd_gpu: regulator@41 {
+		compatible = "silergy,syr828";
+		reg = <0x41>;
+		fcs,suspend-voltage-selector = <1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vsel2_gpio>;
+		regulator-name = "vdd_gpu";
+		regulator-min-microvolt = <712500>;
+		regulator-max-microvolt = <1500000>;
+		regulator-ramp-delay = <1000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vcc5v0_sys>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+};
+
+&i2c1 {
+	i2c-scl-rising-time-ns = <300>;
+	i2c-scl-falling-time-ns = <15>;
+	status = "okay";
+};
+
+&i2c3 {
+	i2c-scl-rising-time-ns = <450>;
+	i2c-scl-falling-time-ns = <15>;
+	status = "okay";
+};
+
+&i2c4 {
+	i2c-scl-rising-time-ns = <600>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+
+	fusb0: typec-portc@22 {
+		compatible = "fcs,fusb302";
+		reg = <0x22>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <RK_PA2 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&fusb0_int>;
+		vbus-supply = <&vcc5v0_typec>;
+		status = "okay";
+	};
+};
+
+&i2s0 {
+	rockchip,playback-channels = <8>;
+	rockchip,capture-channels = <8>;
+	status = "okay";
+};
+
+&i2s1 {
+	rockchip,playback-channels = <2>;
+	rockchip,capture-channels = <2>;
+	status = "okay";
+};
+
+&i2s2 {
+	status = "okay";
+};
+
+&io_domains {
+	status = "okay";
+
+	bt656-supply = <&vcc1v8_dvp>;
+	audio-supply = <&vcca1v8_codec>;
+	sdmmc-supply = <&vcc_sdio>;
+	gpio1830-supply = <&vcc_3v0>;
+};
+
+&pmu_io_domains {
+	pmu1830-supply = <&vcc_3v0>;
+	status = "okay";
+};
+
+&pinctrl {
+	buttons {
+		pwrbtn: pwrbtn {
+			rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	fusb302x {
+		fusb0_int: fusb0-int {
+			rockchip,pins = <1 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	leds {
+		work_led_gpio: work_led-gpio {
+			rockchip,pins = <0 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		diy_led_gpio: diy_led-gpio {
+			rockchip,pins = <0 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	pcie {
+		pcie_pwr_en: pcie-pwr-en {
+			rockchip,pins = <1 RK_PD0 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	pmic {
+		pmic_int_l: pmic-int-l {
+			rockchip,pins = <1 RK_PC5 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+
+		vsel1_gpio: vsel1-gpio {
+			rockchip,pins = <1 RK_PC1 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+
+		vsel2_gpio: vsel2-gpio {
+			rockchip,pins = <1 RK_PB6 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+	};
+
+	sdio-pwrseq {
+		wifi_enable_h: wifi-enable-h {
+			rockchip,pins = <0 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	usb-typec {
+		vcc5v0_typec_en: vcc5v0_typec_en {
+			rockchip,pins = <1 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	usb2 {
+		vcc5v0_host_en: vcc5v0-host-en {
+			rockchip,pins = <4 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&pwm0 {
+	status = "okay";
+};
+
+&pwm2 {
+	status = "okay";
+};
+
+&saradc {
+	vref-supply = <&vcca1v8_s3>;
+	status = "okay";
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-mmc-highspeed;
+	cap-sd-highspeed;
+	cd-gpios = <&gpio0 7 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	max-frequency = <150000000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_bus4>;
+	status = "okay";
+};
+
+&sdhci {
+	bus-width = <8>;
+	mmc-hs400-1_8v;
+	mmc-hs400-enhanced-strobe;
+	non-removable;
+	status = "okay";
+};
+
+&tcphy0 {
+	status = "okay";
+};
+
+&tcphy1 {
+	status = "okay";
+};
+
+&tsadc {
+	/* tshut mode 0:CRU 1:GPIO */
+	rockchip,hw-tshut-mode = <1>;
+	/* tshut polarity 0:LOW 1:HIGH */
+	rockchip,hw-tshut-polarity = <1>;
+	status = "okay";
+};
+
+&u2phy0 {
+	status = "okay";
+
+	u2phy0_otg: otg-port {
+		status = "okay";
+	};
+
+	u2phy0_host: host-port {
+		phy-supply = <&vcc5v0_host>;
+		status = "okay";
+	};
+};
+
+&u2phy1 {
+	status = "okay";
+
+	u2phy1_otg: otg-port {
+		status = "okay";
+	};
+
+	u2phy1_host: host-port {
+		phy-supply = <&vcc5v0_host>;
+		status = "okay";
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_xfer &uart0_cts>;
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&usb_host0_ohci {
+	status = "okay";
+};
+
+&usb_host1_ehci {
+	status = "okay";
+};
+
+&usb_host1_ohci {
+	status = "okay";
+};
+
+&usbdrd3_0 {
+	status = "okay";
+};
+
+&usbdrd_dwc3_0 {
+	status = "okay";
+	dr_mode = "otg";
+};
+
+&usbdrd3_1 {
+	status = "okay";
+};
+
+&usbdrd_dwc3_1 {
+	status = "okay";
+	dr_mode = "host";
+};
+
+&vopb {
+	status = "okay";
+};
+
+&vopb_mmu {
+	status = "okay";
+};
+
+&vopl {
+	status = "okay";
+};
+
+&vopl_mmu {
+	status = "okay";
+};

arch/arm/dts/rk3399-u-boot.dtsi

@@ -10,3 +10,11 @@
 &spi1 {
 	u-boot,dm-pre-reloc;
 };
+
+&uart0 {
+	u-boot,dm-pre-reloc;
+};
+
+&uart2 {
+	u-boot,dm-pre-reloc;
+};