The CPSW3G instance of CPSW on AM62AX SoC provides Ethernet functionality.
Currently, Ethernet is supported on Linux which runs on the A53 core on the
SoC, by allocating all of the DMA resources associated with CPSW to A53_2.
In order to enable use-cases where the Ethernet traffic is sent from or
consumed by various CPU cores on the SoC simultaneously, while at the
same time, maintaining backward compatibility with the existing use-case
of A53 being the sole entity that exchanges traffic with CPSW via DMA,
update the DMA resource sharing scheme on AM62AX SoC to the following:
--------------- -------------- ------------- ----------------
Resource WKUP_R5 MCU_R5 A53_2
--------------- -------------- ------------- ----------------
TX Channels [8] => 4 (Primary) 4 (Primary) 8 (Secondary)
TX Rings [64] => 32 (Primary) 32 (Primary) 64 (Secondary)
RX Channels [1] => 1 (Primary) 0 1 (Secondary)
RX Flows [16] => 6 (Primary) 10 (Primary) 16 (Secondary)
In the absence of primary owners of resources (existing use-case
where A53 owns all of the CPSW DMA resources), the secondary owner
can claim all of the resources as its own. For shared use-cases,
the resources that are not claimed by the primary are communicated
to the secondary owner allowing it to claim them. This ensures that
Linux on A53_2 can continue claiming all DMA resources associated
with CPSW in the absence of primary owners, while at the same time
providing users the flexibility to share CPSW DMA resources across
various CPU cores listed above if needed.
While Linux has been mentioned as the Operating System running
on A53, there is no dependency between the Operating System
running on A53 and its ability to claim the CPSW DMA resources
listed above.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Acked-by: Anshul Dalal <anshuld@ti.com>
Siu Ming Tong <smtong@axiado.com> says:
Patch 1 adds the device tree files: an SoC-level DTSI describing
GIC-v3, Cadence/Zynq UART, a fixed reference clock, and spin-table
secondary CPU boot, plus a board-level DTS setting the console to
uart3 at 115200 baud with 2 GB DRAM at 0x80000000.
Patch 2 adds mach-axiado to support Axiado SoC-based boards, Kconfig
plumbing (AXIADO_AX3005 and TARGET_SCM3005), defconfig, board source
with ft_board_setup() and a MAINTAINERS entry.
Tested on SCM3005 EVK hardware
Link: https://lore.kernel.org/r/20260527-review-v2-0-10daefddf47d@axiado.com
Introduce mach-axiado to support Axiado SoC-based boards. This adds
the platform Kconfig and build infrastructure, along with initial
SCM3005 board support using the AX3005 SoC.
Introduces AXIADO_AX3005, which selects ARM64, driver
model, GIC-v3, and Zynq UART. TARGET_SCM3005 selects ARCH_AXIADO,
allowing future SoC variants to share the platform configuration.
Secondary cores use spin-table boot. ft_board_setup() corrects
the cpu-release-addr in the FDT, which arch_fixup_fdt() overwrites
with the post-relocation address.
Add U-Boot board support for the Axiado AX3005 based targets, a quad-core
ARM Cortex-A53 (ARMv8) platform.
Tested-by: Siu Ming Tong <smtong@axiado.com>
Signed-off-by: Karthikeyan Mitran <kmitran@axiado.com>
Signed-off-by: Siu Ming Tong <smtong@axiado.com>
__FUNCTION__ and __PRETTY_FUNCTION__ are gcc extensions that predate
the C99 __func__ identifier. scripts/checkpatch.pl emits a warning
for any new use of __FUNCTION__ and recommends __func__ instead. In
C (unlike C++) __PRETTY_FUNCTION__ is identical to __func__ because
C function names do not carry signature information, so the
distinction has no behavioural effect here. The majority of the tree
already uses __func__, but a handful of older files in arch/, board/,
boot/, drivers/, examples/ and include/ still carry the gcc spellings
(55 occurrences of __FUNCTION__ across 19 files plus one
__PRETTY_FUNCTION__ in drivers/usb/musb-new/omap2430.c). Convert
them all to the C99 form so the tree is consistent and new patches
in these areas do not have to follow an outdated local style.
Ten "Unnecessary ftrace-like logging - prefer using ftrace" warnings
remain on the printf("%s\n", __func__) and dbg("%s\n", __func__)
function-entry traces in drivers/net/rtl8169.c (behind DEBUG_RTL8169*
preprocessor guards) and drivers/usb/host/ohci-hcd.c. checkpatch
matches the literal "%s\n", __func__ shape regardless of the wrapper,
so silencing those warnings would require changing the debug message
text or removing the traces entirely.
Signed-off-by: Aristo Chen <aristo.chen@canonical.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Read device identification data from a dedicated eMMC region. This
provides:
- Unique device serial number for identification and tracking
- Factory-programmed MAC address for network interfaces
- Bundle information for device variant identification
The serial structure includes CRC32 validation to detect corruption.
On read failure or invalid data, sensible defaults are used to ensure
the system remains bootable.
The fbxserial command provides two subcommands:
- fbxserial show: Display serial info (default)
- fbxserial init: Initialize ethaddr from serial info
Use CONFIG_PREBOOT="fbxserial init" to automatically set MAC addresses
during boot. This approach avoids patching shared board code.
Signed-off-by: Vincent Jardin <vjardin@free.fr>
Reviewed-by: Stefan Roese <stefan.roese@mailbox.org>
Add the emmcboot command as board-specific support for the Nodebox 10G.
This is a legacy boot format that has been in production on this board
for many years so it cannot change anymore. It implements a dual-bank
boot system for reliable firmware updates:
- Bank0: Stable/fallback boot image
- Bank1: Newer/test boot image with reboot tracking
The boot order depends on the nrboot counter stored in eMMC:
- Healthy state (counter < 4): Try Bank1 first, then Bank0
- Degraded state (counter >= 4): Try Bank0 first, then Bank1
Each bank stores an image tag with CRC32 validation. The counter uses
a bit-counting scheme for wear leveling and tracks consecutive failed
boots to trigger automatic fallback.
Signed-off-by: Vincent Jardin <vjardin@free.fr>
Reviewed-by: Stefan Roese <stefan.roese@mailbox.org>
Add board support for the Freebox Nodebox 10G based on the Marvell
Armada 8040 SoC. This board features:
- Quad-core ARMv8 AP806 with dual CP110 companions
- eMMC storage via Xenon SDHCI controller
- 1G SGMII Ethernet on CP0 lane 5
- I2C buses for peripheral access
- NS16550 UART console at 115200 baud
The implementation includes:
- Device tree for the Nodebox 10G hardware
- Dedicated board directory (board/freebox/nbx10g/)
- Board-specific Kconfig and defconfig
The U-Boot comphy bindings (phy-type/phy-speed) differ from the
mainline Linux PHY framework bindings used by phy-mvebu-cp110-comphy,
so U-Boot and the kernel each have their own device tree.
Signed-off-by: Vincent Jardin <vjardin@free.fr>
Reviewed-by: Stefan Roese <stefan.roese@mailbox.org>
All of these platforms enable CONFIG_BOARD_EARLY_INIT_F and then have a
do-nothing board_early_init_f function. Change to not enabling the
option and so not needing an empty function.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Robert Marko <robert.marko@sartura.hr>
Due to this, legacy.c was neither compiled nor linked into the binary
and thus booting legacy DS414 firmware failed. Missing atag setup led to
no console output (and probably stalled boot) after:
| Uncompressing Linux... done, booting the kernel.
Fixes: 9774462e34 ("arm: Disable ATAGs support")
Signed-off-by: Phil Sutter <phil@nwl.cc>
Some boards building this source define CFG_SYS_TCLK as a term involving
readl() which is undefined otherwise.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Add the Allied Telesis x220 board. There are a number of other variants
with the same CPU block that are sold under some different brand names
but the x220 was first.
The x220 uses the AlleyCat3 switch chip with integrated ARMv7 CPU.
Because of this it is reliant on a binary blob for the DDR training. In
upstream u-boot this is replaced by an empty file.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <stefan.roese@mailbox.org>
Select the OF_BOARD_FIXUP and implement board_fix_fdt in board codes of
iMX95/952/94 EVK to handle fuse setting on various part numbers.
Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add fwu_plat_get_alt_num() and fwu_plat_get_bootidx() platform
callbacks required for FWU multi-bank update on Versal and Versal
Gen 2. The boot index is read from the PMC Global PGGS4 register
which is populated by PLM with a magic number and boot partition
index. Uses firmware IOCTL when CONFIG_ZYNQMP_FIRMWARE is enabled,
otherwise falls back to direct MMIO read.
Signed-off-by: Padmarao Begari <padmarao.begari@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20260514102601.1759779-6-padmarao.begari@amd.com
usb_ether_init() called in board_late_init() when CONFIG_USB_ETHER
was enabled without CONFIG_USB_GADGET_DOWNLOAD.
This makes USB ethernet gadget a fixed default, with no way to opt
out at runtime without a rebuild.
Remove the hardcoded call. If USB ethernet gadget functionality is
needed, it can be added via the preboot environment variable.
Signed-off-by: Pranav Sanwal <pranav.sanwal@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20260430093427.1852145-3-pranav.sanwal@amd.com
Replace magic value with documented variable.
While at it, restrict fastboot env guard to USB
as its the only supported fastboot method.
Fixes d000ce5efe ("board: tqma7: add code for u-boot with spl")
Signed-off-by: Alexander Feilke <alexander.feilke@ew.tq-group.com>
The TQMa6UL[L]x is a family of SoMs based on the i.MX6UL[L] SoCs.
They are available either with board connectors or as LGA packages
with solder balls. Add Support for the SoM and its combination with
our MBa6ULx carrier board. For use with the MBa6ULx carrier board,
the LGA variant is soldered onto an adapter board.
Signed-off-by: Nora Schiffer <nora.schiffer@ew.tq-group.com>
Signed-off-by: Max Merchel <Max.Merchel@ew.tq-group.com>
The ram_alias_checks addresses are 32 bit values. When summed as 64 bit
values the calculation is done correctly, otherwise, if they are summed
as 32 bit values, the sum wraps around.
Fix by adding uintptr_t recast to the base address.
Fixes: 60d8255d8d ("board: toradex: add Toradex Verdin iMX95")
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Acked-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Caleb Ethridge <caleb.ethridge@analog.com> says:
This series performs a general cleanup of the default U-boot environment
for sc5xx boards, stemming from the decision to no longer store the
environment in the SPI flash. The environments for each board have been
edited to contain the minimum number of commands needed for all supported
boot modes to avoid confusion, and the default boot command synced to spi
for all boards that support it. The filesystem for the SPI flash has also
been changed from jffs2 to ubifs.
A bug with the Ethernet reset line on the sc594 has been fixed, and the
sc573 has been renamed from the EZKIT to the EZLITE to match the name of the
publically available board. EZKIT was only used internally before release.
Preliminary binman support for sc5xx boards has been removed as it was unused
and full support never added.
Link: https://lore.kernel.org/r/cover.1779370141.git.caleb.ethridge@analog.com
Add fdt_addr_r, kernel_addr_r, and ramdisk_addr_r to the SC5xx boards.
These variables are currently unused in the environment but will be
used in the future once support for booti commands is added to the
SC5xx boards.
Signed-off-by: Caleb Ethridge <caleb.ethridge@analog.com>
Define the boot options for SC598 SOM EZ-LITE so the shared ADI boot
environment includes the expected boot commands for this board.
SC598 SOM EZ-LITE board environment utilizes the shared ADI boot
environment, but it does not define any of the USE_* boot mode selectors.
Without those selectors, the shared env does not generate the board boot
commands such as `spiboot`. This leaves the default `bootcmd=run spiboot`
without a matching environment command and breaks autoboot.
Fixes: c9e893d626 ("board: adi: Add support for SC598")
Signed-off-by: Ozan Durgut <ozan.durgut@analog.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove the SC5XX_LOADADDR Kconfig option, replace its users with
CONFIG_SYS_LOAD_ADDR, and update the ADI boot environment to use
`loadaddr`.
SC5XX_LOADADDR was an ADI-specific duplicate of standard U-Boot
load address handling. U-Boot already uses CONFIG_SYS_LOAD_ADDR
for the default load address and `loadaddr` for boot commands,
so keeping separate SC5XX-specific names is redundant.
Signed-off-by: Ozan Durgut <ozan.durgut@analog.com>
Signed-off-by: Caleb Ethridge <caleb.ethridge@analog.com>
Update the load address for the image in
each environment to match the updated partitions
in Linux.
The partitions in Linux for the spi are named as follows:
- u-boot-spl
- u-boot
- kernel
- rootfs
The kernel partition is at 0x100000 for sc59x family boards,
and 0xd0000 for all other sc5xx boards.
Signed-off-by: Caleb Ethridge <caleb.ethridge@analog.com>
Rename the SC573 EZKIT board to EZLITE across the device tree,
defconfig, board file, and related Kconfig/Makefile entries to
match with release naming. EZKIT was used internally before the
official product release.
Signed-off-by: Caleb Ethridge <caleb.ethridge@analog.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Update the default boot commands to match the expected
bootargs in Linux and new SPI partitioning scheme.
Because the environment is no longer stored in the SPI
flash, imagesize has been removed and replaced with a fixed
length read to load from the SPI. Additionally the partitions
of the mmc have been updated. The first partition holds the fitImage
at /fitImage, and the second partition contains the rootfs.
With this change, the imagefile environment variable has also been
eliminated, the image in the first partition is expected to always
be named fitImage.
Signed-off-by: Caleb Ethridge <caleb.ethridge@analog.com>
Remove the update_spi family of commands from the U-Boot
environment. These commands are not standard in U-Boot,
and boot media programming has moved to Linux, so the
commands can be safely removed.
Additionally, this commit removes the adi_stage2_offset,
adi_rfs_offset, imagefile, jffs2file, and init_ethernet variables that
were consumed by the update commands as they are no longer needed.
CONFIG_SC5XX_UBOOT_OFFSET and CONFIG_SC5XX_ROOTFS_OFFSET are also
removed.
Signed-off-by: Caleb Ethridge <caleb.ethridge@analog.com>
As hinted by its path, it's not really meant to be included outside of
the driver itself. This header uses CONFIG_SYS_RX_ETH_BUFFER which we
are trying to move under CONFIG_NET dependency. This file here can be
compiled without network support so make sure this only gets included
when needed.
The function from that header (fdt_fixup_enetc_mac) is already guarded
by CONFIG_FSL_ENETC so simply guard the inclusion of the header the same
way.
This was tested by building ls1028aqds_tfa_defconfig with
CONFIG_MSCC_FELIX_SWITCH and CONFIG_FSL_ENETC disabled.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Add support for the Geist board based on the Renesas R8A779MD (M3Le) SoC, a
register-compatible variant of the R8A77965 (M3N) with reduced peripherals.
The Geist board design references the Renesas Salvator-X/XS boards, adapting
their configuration for the R8A779MD SoC.
The board will be switched to OF_UPSTREAM once the DTs land in upstream.
Signed-off-by: Huy Bui <huy.bui.pz@bp.renesas.com>
Signed-off-by: Nguyen Tran <nguyen.tran.pz@bp.renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Mirror the j721s2 changes from commit c4fcf9b806 ("board: ti: j7*:
Update rm-cfg and tifs-rm-cfg") to repurpose allocated resources with
version V11.02.07 of k3-resource-partition.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Acked-by: Dominik Haller <d.haller@phytec.de>
Add a separate tifs-rm-cfg.yaml so the TIFS bundle uses the trimmed
TIFS view instead of reusing rm-cfg.yaml, matching the rest of the
AM62 boards.
Mirrors commit 964bda9e80 ("board: ti: am62x: tifs-rm-cfg: Add the
missing tifs-rm-cfg:") for the phyCORE-AM62x SoM.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Ernest Van Hoecke <ernestvanhoecke@gmail.com> says:
This series updates the Resource Management configuration for Toradex
K3-based boards and makes sure the TIFS-specific RM configuration is
used where applicable.
For Verdin AM62P, the tifs-rm-cfg.yaml file is refreshed with
k3-resource-partition V12.00.00 so that it stays in sync with the
existing rm-cfg.yaml update for the v11.02.09 and v12.00.00 TIFS
firmware resource reservation.
For Verdin AM62, the missing tifs-rm-cfg.yaml file is added. The file
matches the TI AM62x configuration, and rm-cfg.yaml was verified to
remain unchanged when regenerated with the same tool version.
For Aquila AM69, both rm-cfg.yaml and tifs-rm-cfg.yaml are updated to
match the resource allocation changes already present in the TI J784S4
configuration files.
Finally, the Verdin AM62 and Verdin AM62P binman descriptions are
updated to use tifs-rm-cfg.yaml for the TIFS RM fragment when building
tiboot3 images, following the same pattern used by the corresponding TI
AM62x/AM62Px platforms.
The generated/updated files were compared against the matching TI board
configuration files where applicable.
Link: https://lore.kernel.org/r/20260508-v1-update-rm-cfg-v1-0-ec9d033f8ec1@toradex.com
Repurpose the allocated resources with version V12.00.00 of
k3-resource-partition, matching the update made for the TI J784S4
configuration files. [1]
The Aquila AM69 rm-cfg.yaml and tifs-rm-cfg.yaml remain aligned with
board/ti/j784s4/*-rm-cfg.yaml.
[1] commit c4fcf9b806 ("board: ti: j7*: Update rm-cfg and tifs-rm-cfg")
Signed-off-by: Ernest Van Hoecke <ernest.vanhoecke@toradex.com>
Acked-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Add the previously missing TIFS RM configuration, generated with
V12.00.00 of k3-resource-partition.
This file is exactly the same as board/ti/am62x/tifs-rm-cfg.yaml.
rm-cfg.yaml and tifs-rm-cfg.yaml need to be in sync, this was already
taken care of by TI. [1]
It was verified that rm-cfg.yaml also remained unchanged with V12.00.00
of the tool.
[1] commit 64ebab10b5 ("toradex: verdin-am62: rm-cfg: Update rm-cfg to reflect new resource reservation")
Signed-off-by: Ernest Van Hoecke <ernest.vanhoecke@toradex.com>
Acked-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
TI updated rm-cfg for v11.02.09 of the TIFS firmware. [1]
Refresh the tifs-rm-cfg.yaml as well, with version V12.00.00 of
k3-resource-partition, so that it remains in sync with rm-cfg.yaml.
rm-cfg.yaml was also updated with V12.00.00 of the tool and noted to
have no changes.
[1] commit a66704e9a1 ("board: toradex: verdin-am62p: rm-cfg: Update rm-cfg to reflect new resource reservation")
Signed-off-by: Ernest Van Hoecke <ernest.vanhoecke@toradex.com>
Acked-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
On the j722s platform, the DM firmware resets the wkup_r5 core at boot to
enable both of its TCM memories.
This reset sequence involves three steps:
- Acquiring processor ownership of wkup_r5
- Configuring the core and requesting a reset via TIFS
- Releasing ownership.
When the Linux remoteproc driver comes up, it acquires ownership of wkup_r5
to query its state, making A53_2 the new owner.
During system suspend, TIFS saves the processor ACL[1] table to DDR as
part of its context.
On resume, TIFS restores the ACL table, leaving A53_2 as the owner of
wkup_r5. At this point, DM (WKUP_0_R5_0 host[2]) no longer has ownership
and is therefore unable to perform the reset sequence it needs,
causing it to crash.
To fix this, configure the wkup_r5[3] processor with dual ownership:
- WKUP_0_R5_0 (Secure) as primary owner.
- A53_2 (Non-Secure) as secondary owner.
[1] https://software-dl.ti.com/tisci/esd/latest/3_boardcfg/BOARDCFG_SEC.html#pub-boardcfg-proc-acl
[2] https://software-dl.ti.com/tisci/esd/latest/5_soc_doc/j722s/hosts.html
[3] https://software-dl.ti.com/tisci/esd/latest/5_soc_doc/j722s/processors.html
Signed-off-by: Abhash Kumar Jha <a-kumar2@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
The load addresses for DFU download binaries were hardcoded for K3
devices which required redefinition of such env for boards that deviated
from the expected K3 memory map (such as AM6254atl EMV).
This patch replaces the hardcoded addresses with their corresponding
Kconfig options making the k3_dfu.env more general.
Signed-off-by: Anshul Dalal <anshuld@ti.com>
In the TI's K3 bootflow of tiboot3.bin -> tispl.bin -> u-boot.img:
(R5 SPL) (A53 SPL)
We currently provide a common dfu_alt_info_ram for both R5 SPL and A53
SPL which is not intuitive in a regular bootflow where each binary
should only request it's immediate next stage.
This patch updates dfu_alt_info_ram such that the R5 SPL would only
request for tispl.bin and A53 SPL would only request u-boot.img.
Signed-off-by: Anshul Dalal <anshuld@ti.com>
Factorize FWU multi-bank support code common to STM32MP1 and
STM32MP2 platforms into a dedicated shared source file.
No functional change intended.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Following commit 4300f9f4c5 ("board: st: stm32mp25: support dynamic
A/B bank bootup"), this patch enables automatic detection of the active
A/B bank on STM32MP15 platforms by retrieving partition GUIDs from FWU
metadata.
This ensures the system correctly identifies the bootable partitions
even in multi-bank scenarios, falling back to a standard bootable flag
scan if the UUIDs are missing.
To enable A/B bank bootup on STM32MP15 boards, add the following Kconfig
options to the stm32mp15[_basic]_defconfig:
CONFIG_FWU_MULTI_BANK_UPDATE=y
CONFIG_FWU_MDATA=y
CONFIG_FWU_NUM_BANKS=2
CONFIG_FWU_NUM_IMAGES_PER_BANK=3
CONFIG_CMD_FWU_METADATA=y
CONFIG_FWU_MDATA_V2=y
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
