[backport from Linux commits 9b26d5c044d6a29ebfb1845408e0f2a7c5f89818
and 219a1f49094f50bf9c382830d06149e677f76bed]
The patch adds the FRIDA FRD400B25025-A-CTK panel, which belongs to the
Novatek NT35510-based panel family.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The Renesas R9A07G044L (RZ/G2L) SoC includes two Gigabit Ethernet
interfaces which can be supported using the ravb driver. Some RZ/G2L
specific steps need to be taken during initialization due to differences
between this SoC and previously supported SoCs. We also need to ensure
that the module reset is de-asserted after the module clock is enabled
but before any Ethernet register reads/writes take place.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
In order to add support for the Renesas RZ/G2L Ethernet IP in a
subsequent patch, we introduce optional de-assertion and re-assertion of
a reset signal in ravb_probe() and ravb_remove().
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
In order to add support for the Renesas RZ/G2L Ethernet IP in a
subsequent patch, we move all R-Car specific code into new functions and
introduce a device_ops function pointer table.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Correctly handle RX errors in ravb_recv() by returning 0 instead
of -EAGAIN on RX error.
In case the RAVB driver detects an RX error in ravb_recv(), it must
not return the -EAGAIN, but instead must return 0. Both error codes
are handled in eth-uclass.c eth_rx() and -EAGAIN is rewritten to 0
at the end of eth_rx(), but negative return code from the .recv()
callback does not trigger .free_pkt() callback, which would clean
up and re-enqueue the descriptor which holds the currently received
corrupted packet. The .free_pkt() must be called for this descriptor,
otherwise the follow up received data become corrupted too, even if
those packets are correctly received. Returning 0 from the .recv()
callback assures the corrupted packet is not processed by the network
stack, but is skipped instead.
For TFTP loading, an RX error produces the timeout "T" output and
resumes the TFTP loading operation shortly afterward, without any
data corruption.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
@protocols is an array of protocol identifiers that are implemented,
excluding the Base protocol. Four protocol identifiers are packed into
each array element. The number of elements of @protocols is specified by
callee-side.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Clock driver based on SCMI clock management protocol in Linux checks
clock state, parent and rate control permissions. To be consistent with
the kernel driver, add this check here. CLOCK_GET_PERMISSIONS is from
ARM System Control and Management Interface Platform Design Document 3.2.
When using common clock framework (CCF), use the clock signal ID to get
the clock registered by clk_register() in scmi_clk_probe(), and then
obatin the struct clk_scmi variable with container_of().
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This patch adds the command CLOCK_PARENT_SET that can be used to set the
parent of a clock. ARM SCMI Version 3.2 supports to change the parent of
a clock device.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Marek Vasut <marex@denx.de>
This patch adds SCMI pin control protocol support to make the pin
controller driver based on SCMI, such as
drivers/pinctrl/nxp/pinctrl-imx-scmi.c, can be bound to the SCMI agent
device whose protocol id is 0x19.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
This patch provides a pinctrl driver based on SCMI pin control protocol.
Currently, only the PINCTRL_CONFIG_SET command is implemented.
Signed-off-by: Ranjani Vaidyanathan <Ranjani.Vaidyanathan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
If there is a SoC specific SCMI protocol driver, using
scmi_proto_driver_get() function can avoid to add SoC specific code to
scmi_agent-uclass.c.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
U_BOOT_SCMI_PROTO_DRIVER macro is used to add a SCMI protocol driver to
scmi_proto_driver list. scmi_proto_driver_get() function can be used to
match a SCMI protocol id and its driver.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
When the cursor position changes, kerning should not be used for the
next character, since it can make the first displayed character shuffle
left or right a bit.
Clear the kern character when setting the position.
Signed-off-by: Simon Glass <sjg@chromium.org>
Provide a way to draw an unfilled box of a certain width. This is useful
for grouping menu items together.
Add a comment showing how to see the copy-framebuffer, for testing.
Signed-off-by: Simon Glass <sjg@chromium.org>
When using expo we want to be able to control the information on the
display and avoid other messages (such as USB scanning) appearing.
Add a 'quiet' flag for the console, to help with this.
The test is a little messy since stdio is still using the original
vidconsole create on start-up. So take care to use the same.
Signed-off-by: Simon Glass <sjg@chromium.org>
When writing multiple lines of text we need to be able to control which
text goes on each line. Add a new vidconsole_put_stringn() function to
help with this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Expo needs to be able to word-wrap lines so that they are displayed as
the user expects. Add a limit on the width of each line and support this
in the measurement algorithm.
Add a log category to truetype while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is useful to be able to embed newline characters in the string and
have the text measured into multiple lines. Add support for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update the vidconsole API so that measure() can measure multiple lines
of text. This will make it easier to implement multi-line fields in
expo.
Tidy up the function comments while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
The CONFIG_WHITE_ON_BLACK setting is hard-coded at build-time. It is
useful to be able to control this when showing menus.
Create a property to hold this information, using the CONFIG as the
initial value.
Signed-off-by: Simon Glass <sjg@chromium.org>
Caleb Connolly <caleb.connolly@linaro.org> says:
Introduce a new event to signal that the live tree has been built,
allowing boards to perform fixups on the tree before devices are bound.
Crucially this allows for devices to be enabled or disabled, but also
allows for properties that are parsed during the bind stage to be
modified (such as dr_mode for dwc3).
With this in place, mach-snapdragon is switched over to use the event
and some hacky U-Boot specific DT overrides (which had to be undone
prior to booting an image) are removed in favour of fixing up the
livetree (which is not passed on to further boot stages).
Finally, some minor fixes are made for the QCM2290 RB1 board, the sdcard
is enabled and it now uses USB host mode in U-Boot like it's bigger
sibling the RB2.
Link: https://lore.kernel.org/r/20250411-livetree-fixup-v2-0-1236823377bb@linaro.org
Some drivers call video_set_flush_dcache() to indicate that they want to
have the dcache flushed for the frame buffer. These drivers benefit from
our new video damage control, because we can reduce the amount of memory
that gets flushed significantly.
This patch enables video damage control for all device drivers that call
video_set_flush_dcache() to make sure they benefit from it.
Signed-off-by: Alexander Graf <agraf@csgraf.de>
[Alper: Add to VIDEO_TIDSS, imply instead of select]
Co-developed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The dcache flushing code path was conditional on ARM && !DCACHE config
options. However, dcaches exist on other platforms as well and may need
clearing if their driver requires it.
Simplify the compile logic and always enable the dcache flush logic in
the video core. That way, drivers can always rely on it to call the arch
specific callbacks.
This will increase code size for non-ARM platforms with CONFIG_VIDEO=y
slightly.
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@csgraf.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/u-boot/20230821135111.3558478-13-alpernebiyasak@gmail.com/
Added workaround for CONFIG_SYS_CACHELINE_SIZE for ibex-ast2700:
Signed-off-by: Simon Glass <sjg@chromium.org>
CONFIG_VIDEO_COPY implemented a range-based copying mechanism: If we
print a single character, it will always copy the full range of bytes
from the top left corner of the character to the lower right onto the
uncached frame buffer. This includes pretty much the full line contents
of the printed character.
Since we now have proper damage tracking, let's make use of that to reduce
the amount of data we need to copy. With this patch applied, we will only
copy the tiny rectangle surrounding characters when we print them,
speeding up the video console.
After this, changes to the main frame buffer are not immediately copied
to the copy frame buffer, but postponed until the next video device
sync. So issue an explicit sync before inspecting the copy frame buffer
contents for the video tests.
Signed-off-by: Alexander Graf <agraf@csgraf.de>
[Alper: Rebase for fontdata->height/w, fill_part(), fix memmove(dev),
drop from defconfig, use damage.xstart/yend, use IS_ENABLED(),
call video_sync() before copy_fb check, update video_copy test]
Co-developed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Link: https://lore.kernel.org/u-boot/20230821135111.3558478-12-alpernebiyasak@gmail.com/
We are going to introduce image damage tracking to fasten up screen
refresh on large displays. This patch adds damage tracking for up to
one rectangle of the screen which is typically enough to hold blt or
text print updates. Callers into this API and a reduced dcache flush
code path will follow in later patches.
Signed-off-by: Alexander Graf <agraf@csgraf.de>
Reported-by: Da Xue <da@libre.computer>
[Alper: Use xstart/yend, document new fields, return void from
video_damage(), declare priv, drop headers, use IS_ENABLED()]
Co-developed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Link: https://lore.kernel.org/u-boot/20230821135111.3558478-5-alpernebiyasak@gmail.com/
Reviewed-by: Simon Glass <sjg@chromium.org>
It's currently possible to make the bootloader crash on calling
clk_set_rate caused by the loop in clk_clean_rate_cache.
The loop assume that every child of the clock node are also clock
device but this is not always the case. For example it's common for a
clock to bind to a reset device or also expose a syscon if the clock
register map is also used to apply special configuration.
In such case, on accessing a device as a clock, the bootloader crash. To
correctly handle this, check if the child device is actually a clock and
ignore otherwise.
Fixes: 6b7fd3128f ("clk: fix set_rate to clean up cached rates for the hierarchy")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
QSPI driver performs chip select operation before every read/write
access. During this operation, driver needs to enable and disable
the QSPI controller. This may cause data loss if there is inadvertent
halting of any ongoing read/write operation. To avoid this scenario,
waiting for the QSPI status to be idle before next read/write
operation is implemented.
Signed-off-by: Naresh Kumar Ravulapalli <nareshkumar.ravulapalli@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
At the moment a mixture of ifdef(CONFIG_IS_ENABLED) and
CONFIG_IS_ENABLED(SPI_FLASH_BAR) is used in the spi-nor framework.
This leads to misbehaviour in the SPL as there is no Kconfig option
CONFIG_SPL_SPI_FLASH_BAR. This commit standardizes the use of
CONFIG_SPI_FLASH to get SPLs that load U-Boot proper from the
SPI flash to work again.
Fixes: 9bb02f7 (mtd: spi-nor: Fix the spi_nor_read() when config SPI_STACKED_PARALLEL is enabled)
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Since the opcode SPINOR_OP_CHIP_ERASE (0xc7) is not supported
for the mt35xu01g/2g flashes, the NO_CHIP_ERASE flag has been added
to enable sector erase functionality instead.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
The mtd partition offset must be calculated first as it will be
referenced when calculating the mtd partition size.
Change-Id: Iccfd101b0a9597ac240c25670da638a82af28980
Fixes: 1ca97ee903 (mtd: mtdpart: Support MTD_SIZE_REMAINING with unallocated memory area)
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Reported-by: Francesco Dolcini <francesco@dolcini.it>
As this driver needs to use the special sandbox <asm/malloc.h> header
rather than normal malloc, it must be careful of the includes it brings
in. It does not need <spi.h> for anything, so drop it.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Currently, the phy_config() API is invoked by the driver only once since it
has been probed. While this works in general, it doesn't allow the driver
to bring the PHY back to its default reset state. As a result, the driver
might not be able to recover the PHY from a bad state. To address this,
move phy_config() into the driver's start callback (am65_cpsw_start()).
Apart from providing the means to recover the PHY in the event of failure,
the implementation is in line with the idea of "reset and configure" that
is already followed by am65_cpsw_start() when it comes to programming the
CPSW MAC.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
We have improvements to the reliability of H6 and H616 DRAM
initialisation, hopefully avoiding those occasional size misdetections
many people reported before.
Also there is some modernisation of the USB PHY code, to use DT provided
regulators and GPIOs, instead of relying on this being badly duplicated
in Kconfig. This also happens to fix broken USB operations for older
boards (using the A20 SoCs, for instance), which were clashing over
grabbing some GPIOs, leading to a driver bailout. There is also some
rework of the H6/H616 SPL clock code, to prepare it for being reused by
the upcoming Allwinner A523 support. This drops the usage of C structs
to model MMIO register frames, and replaces them by using an addition of
the base address with a macro defined offset. Also in preparation for
A523 there is one fix and one addition for the FEL code, to prepare for
the GICv3 interrupt controller that the new SoC uses. And since this is
a simple fix, and was ready, there is also the watchdog driver for that
new SoC. Finally tossing in an easy fix to some H616 defconfig files to
enable eMMC.
I also use the opportunity to enable proper page table protection
(observing read-only and no-execute attributes), support for which the
arm64 port recently gained. I didn't spot any issues on my arm64 board
tests, but it can be easily disabled or backed out again in case any
issues arise.
Full support for the two new SoC series (A133 and A523) we are working
on is not quite ready yet, but might follow still a bit later if
progress permits.
CI passed, and boot-tested on at least one board with a H616, H6, A64,
H3, A20, T113s.
The Allwinner MMC code uses a complex C struct, modelling the clock
device's register frame. We rely on sharing the member names across all
Allwinner SoCs, which is fragile.
Drop the usage of the struct in the MMC code, by using #define'd
register names and their offset, and then adding those names to the base
pointer. This requires to define those offsets for all SoCs, but since we
only use between four and six clock registers in the MMC code, this is
easily done.
This removes one common user of the clock register struct.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
