The Powkiddy X55 is a Rockchip RK3566 based handheld gaming device.
UART, ADC, eMMC, and SDMMC are tested to work in U-Boot and this
successfully boots mainline Linux.
Kernel commit:
e99adc97e21a ("arm64: dts: rockchip: Add Powkiddy X55")
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
U-Boot proper pre-reloc is currently running out of memory and it is
thus impossible to boot into U-Boot CLI.
Fix this by migrating to the common bss and stack addresses for PX30,
which drastically increases the size of the pre-reloc allocation pool (8
times bigger now). The memory layout in SPL and U-Boot proper now
match the other SoCs' using ROCKCHIP_COMMON_STACK_ADDR.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
See commit 008ba0d56d ("rockchip: Add common default bss and stack
addresses") for memory layout. This migrates PX30 to use the new layout,
except for TPL. Indeed, PX30 is extremely limited in SRAM, so we need to
be extra careful about what goes into the TPL and how much we can
allocate there, so let's keep the current value for
TPL_SYS_MALLOC_F_LEN (already present in the PX30-specific Kconfig, from
an earlier commit).
This will allow us to use the same memory layout on one more Rockchip
SoC, which is always a nice thing. Additionally, this will make it
easier to fix U-Boot proper pre-reloc running out of memory on PX30 in a
subsequent commit.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
This is the kind of setting that typically doesn't need to be changed
between boards based on the same SoC, so let's make it the default in
PX30 Kconfig so we don't have to care about it in the defconfig if we
don't want to.
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
All parts expect the SPLL to run at 702MHz. In U-Boot it's the SPLL_HZ
declaring this rate and in the kernel it's a fixed clock definition.
While everything is expecting 702MHz, the SPLL is not running that
frequency when coming from the bootrom though, instead it's running
at 351MHz and the vendor-u-boot just sets it to the expected frequency.
The SPLL itself is located inside the secure-BUSCRU and in theory
accessible as an SCMI clock, though this requires an unknown amount
of cooperation from trusted-firmware to set at a later stage, though
during the SPL stage we can still access the relevant CRU directly.
The SPLL is for example necessary for the DSI controllers to produce
output.
As the SPLL is "just" another rk3588 pll, just set the desired rate
directly during the SPL stage.
Tested on rk3588-rock5b and rk3588-tiger by reading back the PLL rate
and also observing working DSI output with this change.
Fixes: 6737771600 ("rockchip: rk3588: Add support for sdmmc clocks in SPL")
Suggested-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Migrate RV1126 boards that exists in Linux v6.8 to use OF_UPSTREAM.
Following targets is migrated to use OF_UPSTREAM:
- rv1126-edgeble-neu2 : Board is an industrial form factor
IO board.
- sonoff-ihost-rv1126 : Gateway device designed to provide a
Smart Home Hub.
Cc: Tim Lunn <tim@feathertop.org>
Cc: Jagan Teki <jagan@edgeble.ai>
Reviewed-By: Tim Lunn <tim@feathertop.org>
Tested-By: Tim Lunn <tim@feathertop.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Anand Moon <anand@edgeble.ai>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
After the conversion of RV1108 to OF_UPSTREAM,
include/dt-bindings/clock/rv1108-cru.h is no longer needed because
there is dts/upstream/include/dt-bindings/clock/rv1108-cru.h from
upstream Linux.
Remove the unneeded rv1108-cru.h file.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d, reversing
changes made to 2ee6f3a5f7.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
Specifying a file in an EXT4 or FAT partition on a virtio device as
environment location failed because virtio hadn't been initialized by
the time the environment was loaded. This patch mirrors commit
54ee5ae841 ("Add SCSI scan for ENV in EXT4 or FAT") in issue and
fix, just for a different kind of block device.
The additional include in include/virtio.h is needed so all functions
called there are defined, the alternative would have been to include
dm/device.h separately in the env/ sources.
Checkpatch suggests using "if (IS_ENABLED(CONFIG...))" instead of
"#if defined(CONFIG_...)", I'm sticking to the style of the existing
code here.
Signed-off-by: Fiona Klute <fiona.klute@gmx.de>
CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Bin Meng <bmeng.cn@gmail.com>
CC: Rogier Stam <rogier@unrailed.org>
u-boot-dfu-20240516
- Fix cdns3 low power hang via fast access bit
- Multiple dwc3 gadget fixes, mainly for USB support on TI AM6232
- Consistent USB_GADGET_MANUFACTURER for PHYTEC boards
- MAINTAINERS file update for u-boot-dfu
Upstream Linux commit 87dd96111b0b.
When operating in USB 2.0 speeds (HS/FS), if GUSB2PHYCFG.ENBLSLPM or
GUSB2PHYCFG.SUSPHY is set, it must be cleared before issuing an endpoint
command.
Current implementation only save and restore GUSB2PHYCFG.SUSPHY
configuration. We must save and clear both GUSB2PHYCFG.ENBLSLPM and
GUSB2PHYCFG.SUSPHY settings. Restore them after the command is
completed.
DWC_usb3 3.30a and DWC_usb31 1.90a programming guide section 3.2.2
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20240412202611.3565052-5-alexander.sverdlin@siemens.com
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
This [pull request] for master fixes framebuffer video on almost all
Qualcomm platforms where the framebuffer is initialised by the first
stage bootloader.
* We already have a header 'backtrace', there is no need to repeat the
word backtrace on every line.
* Add a blank line before the backtrace section of the crash report for
improved readability.
* If U-Boot is compiled without backtrace, there is no need to write a
message at all.
* Avoid #ifdef. We prefer functions to always be compiled and let
the linker remove them if not needed.
* Foresee 3 digits for the backtrace index.
For testing the 'exception' command can be used.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
As boards from multiple vendors (Milk-V, StarFive, Pine64) use the mac
command provide a sub-command to set the vendor string.
Reported-by: E. Shattow <lucent@gmail.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
We can use U-Boot for recovering JH7110 based boards via UART
if CONFIG_SPL_YMODEM_SUPPORT=y.
* Send u-boot-spl.normal.out via XMODEM.
* Send u-boot.itb via YMODEM.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: E. Shattow <lucent@gmail.com>
Provide a man-page describing the usage of U-Boot on
the Milk-V Mars CM and Milk-V Mars CM Lite boards.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: E Shattow <lucent@gmail.com>
We already support the VisionFive 2 and the Milk-V Mars board by
patching the VisionFive 2 device tree. With this patch the same
is done for the Milk-V Mars CM.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Tested-by: E. Shattow <lucent@gmail.com>
Reviewed-by: E. Shattow <lucent@gmail.com>
The EEPROM provides information about the size of the eMMC.
Provide a new function get_mmc_size_from_eeprom() to read it.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: E. Shattow <lucent@gmail.com>
Without the NULL check, if the devicetree that u-boot loads does not have a
compatible property then a store access fault will be raised and force the
machine to reset, due to the NULL pointer we passed to strlen. This commit
adds this check and will return -ENOSPC to indicate the get_desc failed.
Signed-off-by: Hanyuan Zhao <zhaohy22@mails.tsinghua.edu.cn>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
When the device port is in a low power state [U3/L2/Not Connected],
accesses to usb device registers may take a long time. This could lead to
potential core hang when the controller registers are accessed after the
port is disabled by setting DEVDS field. Setting the fast register access
bit ensures that the PHY clock is keeping up in active state.
Therefore, set fast access bit to ensure the accesses to device registers
are quick even in low power states.
commit b5148d946f45 ("usb: cdns3: gadget: set fast access bit") in the
upstream kernel is taken as reference.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20240424073911.1943-1-r-gunasekaran@ti.com
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
The newly introduced carve_out_reserved_memory causes issues when
U-Boot is chained from the lk2nd bootloader. lk2nd provides a
simple-framebuffer device and marks the framebuffer region as no-map in
the supplied /reserved-memory. Consequently, the simple_video driver
triggers a page fault when it tries to write to this region.
As per Caleb's advice, this simple patch only does the carveouts for the
qcs404 SoC for which it was originally designed. The intent is to do the
carveouts for more Qualcomm SoCs in future.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Move GPIO pinmux to MDIO node. Add GB Ethernet reset GPIO.
Add PIN_INPUT to Fix SPE ethernet reset gpio so that
reading the GPIO can give correct status.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
While we unlikely to have an issue with CVE-2024-22195, it is simple
enough to bump our version of Jinja2 to receive the fix, do so.
Reported-by: GitHub dependabot
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
On all Raspberry Pi platforms, we're loaded by a prior stage firmware
that has assembled and passed on a device tree binary for us to use.
Switch to using this tree by default.
Cc: Matthias Brugger <mbrugger@suse.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: François Ozog <francois.ozog@linaro.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Simon Glass <sjg@chromium.org>
Remove DTs which are now replaced by OF_UPSTREAM counterparts.
No functional change expected.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Adam Ford <aford173@gmail.com> #beacon boards
MD Danish Anwar <danishanwar@ti.com> says:
This series adds AM64x related compatibles to PRUSS and PRU_RPROC drivers.
This series is a prerequisite for ICSSG Ethernet driver.
Once Support for AM64x is added to PRUSS and PRU_RPROC driver, I'll send
another series to enable ICSSG Ethernet driver for AM64x as well.
Let's provide get_boot_device() for AM64, similar to what we did
in commit 2f9095e2bf ("arm: mach-k3: am625: Provide a way to obtain boot
device for non SPLs") for AM62.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Add support for AM64x by adding it's compatible in pruss driver.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Add support for AM64x PRU cores by adding compatibles for AM64x.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
J7200 has SR1.0 and SR2.0 having three variants of each GP, HS-FS and
HS-SE. Current build does not generate HS-SE SR1.0 and HS-FS SR1.0 so
add support for them.
Reported-by: Suman Anna <s-anna@ti.com>
Reported-by: Aniket Limaye <a-limaye@ti.com>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
J721E has SR1.1 and SR2.0 having three variants of each GP, HS-FS and
HS-SE. Current build does not generate HS-FS SR1.1 so add support for
them.
Reported-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Enable CONFIG_BOARD_LATE_INIT to use PHYTECs common board_late_init()
to set handy environment variables for u-boot.
Also, resync after savedefconfig.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
