- Add TPM support for venice boards
- Add networking support for imx93-evk
- Enable TCP, IPv6, wget for DHCOM and Data Modul boards
- Enable fastboot support for Toradex boards
- Allow pico-imx7d to boot from SD
- Enable fastboot for beacon imx8m beacon boards, disabled
SYS_CONSOLE_IS_IN_ENV
- Fix mxsboot to prevent NAND blocks being reported as bad
- Add imx8mm PWM clock support
- Several devicetree syncs with the kernel
- Add support for i.MX8MP Polyhex Debix Model A SBC
- Reworked ddr_load_train_firmware() to get a 50ms boot time improvement
Move the DM entry in tispl.bin FIT image from default fetching an
external blob entry to fetching using ti-dm entry type. This way, the
DM entry will be populated by the TI_DM pathname if provided. Else it
will resort to the ti-dm.bin file.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Function acpi_get_rsdp_addr() is needed on all architectures which
write ACPI tables. Move the definition from the x86 include to an
architecture independent one.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add basic sandbox support for 'booti' so we can start to boot the test
ARMbian image. This is helpful in checking that it is parsed correctly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Technexion PICO-IMX7 SoM is supporting USDHC3 (eMMC or micro SD on SoM)
and USDHC1 (SD on carrier board) to use on any carrier board like
PICO-NYMPH. Based on the U-Boot version from Technexion it adds
baseboard SD card boot detect to able to boot from selected USDHC1
or USDHC3 boot devices.
Signed-off-by: Benjamin Szőke <egyszeregy@freemail.hu>
Tested-by: Fabio Estevam <festevam@gmail.com>
Selecting CONFIG_IMX_HAB=y on a SPL target, such as apalis_imx6_defconfig,
for example, leads to the following build error:
/usr/bin/arm-linux-gnueabihf-ld.bfd: arch/arm/mach-imx/hab.o: in function `imx_hab_is_enabled':
arch/arm/mach-imx/hab.c:879: undefined reference to `fuse_read'
fuse_read() comes from SPL_MXC_OCOTP, which depends on SPL_DRIVERS_MISC,
since commit 251a3053b1 ("misc: imx: remove DM dependency for ocotp
driver in SPL").
Select SPL_DRIVERS_MISC in the SPL case to fix this build issue.
Reported-by: Lisandro Pérez Meyer <lpmeyer@ics.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-by: Lisandro Pérez Meyer <lpmeyer@ics.com>
The MXS starts with CPSR V bit set, which makes the CPU jump to high vectors
in case of an exception. Those high vectors are located at 0xffff0000, which
is where the BootROM exception table is located as well. U-Boot should handle
exceptions on its own using its own exception handling code, which is located
at 0x0, i.e. at low vectors. Clear the CPSR V bit, so that the CPU would jump
to low vectors on exception instead, and therefore run the U-Boot exception
handling code.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
To quote the author:
It would be useful to be able to boot an OS when CONFIG_CMDLINE is
disabled. This could allow reduced code size.
Standard boot provides a way to handle programmatic boot, without
scripts, so such a feature is possible. The main impediment is the
inability to use the booting features of U-Boot without a command line.
So the solution is to avoid passing command arguments and the like to
code in boot/
A similar process has taken place with filesystems, for example, where
we have (somewhat) separate Kconfig options for the filesystem commands
and the filesystems themselves.
This series starts the process of refactoring the bootm logic so that
it can be called from standard boot without using the command line.
Mostly it removes the use of argc, argv and cmdtbl from the internal
logic.
Some limited tidy-up is included, but this is kept to smaller patches,
rather than trying to remove all #ifdefs etc. Some function comments
are added, however.
A simple programmatic boot is provided as a starting point.
This work will likely take many series, so this is just the start.
Size growth with this series for firefly-rk3288 (Thumb2) is:
arm: (for 1/1 boards) all +23.0 rodata -49.0 text +72.0
This should be removed by:
https://source.denx.de/u-boot/custodians/u-boot-dm/-/issues/11
but it is not included in this series as it is already large enough.
No functional change is intended in this series.
Changes in v3:
- Add a panic if programmatic boot fails
- Drop RFC tag
Changes in v2:
- Add new patch to adjust position of unmap_sysmem() in boot_get_kernel()
- Add new patch to obtain command arguments
- Fix 'boot_find_os' typo
- Pass in the command name
- Use the command table to provide the command name, instead of "bootm"
Since we can now cleanly disable CMDLINE when needed, drop the rules
which discard the command code. It will not be built in the first
place.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
When CONFIG_DWC_ETH_QOS_IMX=y and CONFIG_FEC_MXC is not selected, the
following warning is seen:
arch/arm/mach-imx/imx8m/clock_imx8mm.c: In function 'board_interface_eth_init':
arch/arm/mach-imx/imx8m/clock_imx8mm.c:914:24: warning: implicit declaration of function 'imx8mp_fec_interface_init; did you mean 'imx8mp_eqos_interface_init'? [-Wimplicit-function-declaration]
Fix it by adding a stub for imx8mp_fec_interface_init() to handle this
case.
This follows the same approach done on imx8mp_eqos_interface_init().
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
With DM enabled, there is no need for board code to initialize
the Ethernet interfaces.
The RTL8211FDI Ethernet PHYs have 25MHz oscillator, so there is no
need to enable the RGMII TX clk output.
Also, there is no need for describing the deprecated phy-reset FEC
properties, nor passing reset properties to the EQOS interface in
u-boot.dtsi.
Remove all these unneeded pieces.
Tested both Ethernet interfaces after these changes.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Sync imx8mm.dtsi with linux-next 20231019.
The motivation for doing this sync was a bug when doing "ums 0 mmc 1"
on imx8mm-evk. It worked well for the first time, but after doing
a CTRL+C and launching the ums again, the command did not work.
Adam Ford suggested to sync imx8mm.dtsi with the Linux dts, as there was
a recent USB power domain reorganization there.
After syncing the imx8mm.dtsi with Linux, the ums command works without
problem after a CTRL+C.
Suggested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Currently, the imx8mp_evk uses the non-DM code to initialize the PMIC.
Convert to DM_PMIC, which is the recommended way to access the PMIC.
While at it, fix multi-line comments style.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Add the TPM device found on the GW73xx revision F PCB.
This hangs off of SPI2, uses gpio1_10 as a CS and gpio1_11 as RST#.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add the TPM device found on the GW73xx revision F PCB.
This hangs off of SPI2, uses gpio1_10 as a CS and gpio1_11 as RST#.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add Variscite manufacturer to the IMX8MN_VAR_SOM target menu label as
the majority of targets include the manufacturer as part of their menu
description/label and it helps when looking for a particular
manufacturer/board.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The correct compatible string for i.MX93 variant of DWC EQoS MAC is now
"nxp,imx93-dwmac-eqos".
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Add a common board_interface_eth_init() called by the DWC MAC driver to
setup the MAC <-> PHY interface according to the PHY mode obtained from
DT.
Remove the board-side configuration in the i.MX93 EVK files.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Change boot device logic to also allow environment stored in fat and
in ext4 when booting from SD or eMMC.
As the boot device check for SD and for eMMC was depending on
ENV_IS_IN_MMC being defined, change the ifdef blocks at
env_get_location to use IS_ENABLED instead for all modes, returning
NOWHERE when no valid mode is found.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Co-developed-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
The interrupt collector macro name for i.MX23 is MXS_ICOLL_BASE,
this is correct and matches the documentation of both i.MX23 and
i.MX28. Align the i.MX28 macro accordingly. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Sync the devicetree files used in the kernel for the imx8mm-phyboard-polis
with the corresponding devicetree files in U-Boot.
Replaced phycore-imx8mm.dts with kernel dts imx8mm-phyboard-polis-rdk.dts
Synced with kernel 6.5.0-rc1 commit
e752a4f9589c (arm64: dts: freescale: imx8mm-phyboard: Add I2C4 pinmuxing)
Signed-off-by: Cem Tenruh <c.tenruh@phytec.de>
Commit 0aea5dda29 ("ARM: dts: imx7d-sdb-u-boot: Fix usdhc1 UHS
operation") did a temporary workaround by addng the usdhc1 fix
inside the -u-boot.dtsi file.
The imx7d-sdb.dts from kernel 6.5-rc1 contains the proper UHS
fix, so sync the devicetree tree and remove the previous fix
from -u-boot.dtsi.
Also, adjust the PMIC node name inside pmic_get() to match
the devicetree update.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Add support for the Polyhex Debix Model A SBC board.
It is an industrial grade single board computer based on
NXP's i.MX 8M Plus.
Currently supported interfaces are:
- Serial console
- Micro SD
- eQOS and FEC Ethernet
imx8mp-debix-model-a.dts is taken from Linux 6.3.
Signed-off-by: Gilles Talis <gilles.talis@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
As requirement of CR side, QSPI Flash usage via RPC driver shall
be disabled and leaving the control of this module to CR side.
Perform DT modification to disable the RPC SPI.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Cong Dang <cong.dang.xn@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Do not modify defconfig, modify the DT instead, this way
the RPC SPI can be enabled without recompiling the U-Boot
itself. Update commit message accordingly.]
Use the phandle reference to &rpc node in arch/arm/dts/r8a779g0.dtsi
and remove properties which are already in arch/arm/dts/r8a779g0.dtsi.
No functional change and no resulting DT change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
To quote the author:
This series imports generic versions of ioread_rep/iowrite_rep and
reads/writes from Linux. Some cleanup is done to make sure that all
platforms have proper defines for implemented functions and there are no
redefinitions.
Add defines for __raw_{read,write}{b,w,l}() functions to make
make asm-generic/io.h aware of them.
Signed-off-by: Igor Prusov <ivprusov@salutedevices.com>
Change type of address parameter from int* to volatile void* for
{read,write}s{b,w,l}() functions and add const qualifier for reads. This
is done to keep function signatures in sync with asm-generic/io.h and
other platforms.
Signed-off-by: Igor Prusov <ivprusov@salutedevices.com>
Add defines for {read,write}{b,w,l,q}(), {read,write}s{b,w,l,q}() and
{in,out}s{b,w,l,q}() functions to make asm-generic/io.h aware of them.
Signed-off-by: Igor Prusov <ivprusov@salutedevices.com>
Currently reads{b,w,l}() functions don't have const qualifier for their
address parameter. Since asm-generic/io.h in Linux has const for all
read functions, add it here as well to keep signatures in sync.
Signed-off-by: Igor Prusov <ivprusov@salutedevices.com>
Add defines for {in,out}s{b,w,l}() functions to make sure that
they will be used by asm-generic/io.h
Signed-off-by: Igor Prusov <ivprusov@salutedevices.com>
Generic version of io.h should be included at the end of
architecture-specific ones to make sure that arch implementations are
used and to avoid redefinitions.
Signed-off-by: Igor Prusov <ivprusov@salutedevices.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To quote the author:
The show_board_info() function was adjusted to weak so that it could be
entirely replaced with a board-specific implementation.
The intended way for boards to provide their own information is via a
sysinfo driver. But currently there is no way to show anything other
than the model name.
This series adds support for showing a few more items, in a way that is
easy for boards to extend.
Since there is already a weak checkboard() function, we don't need to
have two levels of weak function here. So this series drops the weak
attribute from show_board_info()
Existing boards will see a slight change in output, in that the model
name will appear first, before any custom output. If that is a problem,
then the solution is to implement a sysinfo driver for the board.
