Instead of resolving clock control flags using SCMI_CLOCK_ATTRIBUTES
during probe for each and every clock, resolve the clock control
flags using SCMI_CLOCK_ATTRIBUTES when the clock control flags are
first used. Because most clock are never used by U-Boot, this allows
reducing the amount of SCMI_CLOCK_ATTRIBUTES considerably, and this
improve probe time of the scmi clock driver and U-Boot start up time.
On Renesas X5H, with 1700+ SCMI clock, the boot time improved by 1.7s .
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The clock names are retrived via SCMI_CLOCK_ATTRIBUTES, called for each
clock ID. This may take a lot of time to complete and is not strictly
necessary. Register each clock as "scmi-%zu" instead, and let the first
call of SCMI_CLOCK_ATTRIBUTES fill in the actual clock name.
This has a side effect, which can be considered both an upside and also
a downside. Unused clock are never renamed and retain their placeholder
"scmi-%zu" name, which avoids empty clock names for nameless SCMI clock,
and avoids the name resolution and improves boot time. But for those
SCMI clock which do have name, that name is not listed until the clock
are used.
This is a preparatory patch for deferred issue of SCMI_CLOCK_ATTRIBUTES.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Pull clock control flags resolution into dedicated function and
call it from each site that does access clock control flags. No
functional change.
This is a preparatory patch for deferred issue of SCMI_CLOCK_ATTRIBUTES.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Allocate all sub-driver instance data at once. The amount of data that
have to be allocated is known up front, so is the size of the data, so
there is no need to call malloc() in a loop, mallocate all data at once.
The upside is, less heap fragmentation and fewer malloc() calls overall,
and a faster boot time.
The downside is, if some of the clock fail to register, then the clock
driver cannot free parts of the bulk allocated sub-driver instance data.
Such a failure can only occur if clk_register() were to fail, and if that
happens, the system has more significant problems. Worse, if a core clock
driver fails to probe, the system has even bigger problem.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When not using Common clock framework(CCF), calls to
scmi_clk_set_parent returns -ENOTSUPP, which should not be the case.
Fix that.
Fixes: 15fdfef664 ("clk: scmi: check the clock state/parent/rate
control permissions)
Signed-off-by: Kamlesh Gurudasani <kamlesh@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
SCMI v3.2 introduces a new clock CONFIG_SET message format that can
optionally carry also OEM specific configuration values beside the usual
clock enable/disable requests. Add support to use such new format when
talking to a v3.2 compliant SCMI platform.
Support existing enable/disable operations across different clock protocol
versions: this patch still does not add protocol operations to support the
new OEM specific optional configuration capabilities.
No functional change for the SCMI drivers users of the related enable and
disable clock operations.
[Marek: Remodel after Linux e49e314a2cf7 ("firmware: arm_scmi: Add clock v3.2 CONFIG_SET support")
Support both old < 2.1 and new >= 2.1 protocol versions.
Update commit message based on Linux one]
Signed-off-by: Vinh Nguyen <vinh.nguyen.xz@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu> says:
This patch series adds basic support for the boards based on Airoha
EN7523/EN7529/EN7562 SoCs. Due to ATF restrictions these boards are
able to run 32-bit OS only.
This patch series adds support for the following hardware:
* console UART
* ethernet controller/switch
* spinand flash (in non-dma mode)
The following issues may be expected:
* Extra slow UBI attaching in U-Boot (up to 20 sec with fastmap enabled).
This is caused by the lack of DMA support in the U-Boot airoha-snfi driver.
* Linux airoha-snfi driver in some cases might damage you flash data
(see: https://lore.kernel.org/lkml/20251012121707.2296160-15-mikhail.kshevetskiy@iopsys.eu/)
* Latest linux kernel is recommended to properly support flashes
with more than one plane per lun
(see: https://lore.kernel.org/lkml/20251012121707.2296160-7-mikhail.kshevetskiy@iopsys.eu/)
* It's NOT recommended to use flashes working in continuous mode because
U-Boot airoha-snfi driver does not support such flashes properly.
The patches was tested on the board:
- SoC: Airoha EN7562
- RAM: 512 MB
- SPI NAND: 4 Gbit, made by Toshiba
- Linux boot: was NOT tested
The U-Boot was chain-loaded from the running U-Boot. Airoha ATF-2.3 does
not allow easily chain-loading of U-Boot from U-Boot, so a special FIT
image (mimic linux kernel) was created
1) Create u-boot.its file with the following contents:
=== cut here ===
/dts-v1/;
/ {
description = "ARM OpenWrt FIT (Flattened Image Tree)";
#address-cells = <1>;
images {
u-boot-ram {
description = "OpenWrt U-Boot RAM image";
data = /incbin/("u-boot.bin.lzma");
type = "kernel";
arch = "arm";
os = "linux";
compression = "lzma";
load = <0x81e00000>;
entry = <0x81e00000>;
hash@1 {
algo = "crc32";
};
hash@2 {
algo = "sha1";
};
};
fdt-1 {
description = "OpenWrt device tree blob";
data = /incbin/("dts/upstream/src/arm/airoha/en7523-evb.dtb");
type = "flat_dt";
arch = "arm";
compression = "none";
hash@1 {
algo = "crc32";
};
hash@2 {
algo = "sha1";
};
};
};
configurations {
default = "config-ram-uboot";
config-ram-uboot {
description = "OpenWrt RAM U-Boot";
kernel = "u-boot-ram";
fdt = "fdt-1";
};
};
};
==================
2) Create u-boot.itb image to chain-load new u-boot from the old one
lzma_alone e u-boot.bin u-boot.bin.lzma
mkimage -f u-boot.its u-boot.itb
3) Load new u-boot from the old one
U-Boot> tftpboot u-boot.itb && bootm
Link: https://lore.kernel.org/r/20251101004503.2379529-1-mikhail.kshevetskiy@iopsys.eu
This adds clock driver for airoha en7523/en7529/en7562 SoCs. The code
is based on corresponding linux driver.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Isolate Renesas R-Car Gen3 clock driver to R-Car Gen3 and Gen4 and RZ/G2L.
The Renesas R-Car Gen5 uses SCMI clock protocol driver instead. This is
a preparatory change for R-Car Gen5. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add dummy implementation of set_rate for SCLK_GPU and SCLK_WIFI_PMU to
allow use of dts/upstream assigned-clocks in cru and pmucru nodes.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This reverts commit 644b4650ee.
While the intention of the above commit is correct, it leads to test
failures in CI that need to be addressed at the same time.
Signed-off-by: Tom Rini <trini@konsulko.com>
A few clock drivers cannot build without access to some platform
specific header files. Express those requirements in Kconfig as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
In clk_set_default_get_by_id ret is passed to ERR_PTR but nothing is
done with the value that this calculates which is obviously not the
intention of the code. This is confirmed by the code around where this
function is called.
Instead return the value from ERR_PTR.
This issue found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Acked-by: Quentin Schulz <quentin.schulz@cherry.de>
In versaclock_probe vc5->pin_xin may be an error pointer so need to
check with IS_ERR before attempting to dereference it.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
In versaclock_get_name -ENOMEM is passed to ERR_PTR but nothing is
done with the value that this calculates which is obviously not the
intention of the code. This is confirmed by the code around where this
function is called.
Instead return the value from ERR_PTR.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Remove default values for PMC PLL Analog Control Register(ACR) as the
values are specific for each SoC and PLL, so load them from PLL
characteristics structure
Signed-off-by: Manikandan Muralidharan <manikandan.m@microchip.com>
Signed-off-by: Varshini Rajendran <varshini.rajendran@microchip.com>
The cv1800b_clk_setfield function returns void, but was doing "return
writel(...);" and while seemingly having a void function return a void
function is not a warning, when readl is a macro this problem is shown.
Correct the code to instead simply call writel.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Yao Zi <ziyao@disroot.org>
Peng Fan (OSS) <peng.fan@oss.nxp.com> says:
Misc update on firmware scmi:
- Typo fix
- Use io helpers
- Use PAGE_SIZE for arm64
- Add IN_USE error code
- Add more error info
- Support scmi max rx timeout in mailbox
- Add myself as scmi maintainer, AKASHI contributed most code, but
seems he is not invovled in the developement anymore, I volunteer to
help here.
Some items on list that I am thinking to add:
- align with linux kernel to use cpu_to_le32 and le32_to_cpu, but have not find
a good way to use the helpers.
- Add SCMI version negotiation as Linux Kernel
Link: https://lore.kernel.org/r/20250927-scmi-v1-0-5e9354fb3bff@nxp.com
Use dev_dbg to dump device name, dev_dbg also a encapsulation call
to log() and print(). So it is ok to use dev_dbg.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
SoCFPGA updates for v2025.10:
CI: https://source.denx.de/u-boot/custodians/u-boot-socfpga/-/pipelines/27762
This pull request brings a set of updates across SoCFPGA platforms
covering Agilex5, Agilex7, N5X, and Stratix10. The changes include:
* Agilex5 enhancements:
- USB3.1 enablement and DWC3 host driver support
- System Manager register configuration for USB3
- Watchdog timeout increase and SDMMC clock API integration
- dcache handling improvements in SMC mailbox path
- Enable SPL_SYS_DCACHE_OFF in defconfig
* Clock driver improvements:
- Introduce dt-bindings header for Agilex clocks
- Add enable/disable API and EMAC clock selection fixes
- Replace manual shifts with FIELD_GET usage
* DDR updates:
- IOSSM mailbox compatibility check
- Correct DDR calibration status handling
* Device tree changes:
- Agilex5: disable cache allocation for reads
- Stratix10: add NAND IP node
- Enable driver model watchdog
- Enable USB3.1 node for Agilex5
* Config cleanups:
- Simplify Agilex7 VAB defconfig
- Remove obsolete SYS_BOOTM_LEN from N5X VAB config
- Enable CRC32 support for SoCFPGA
- Increase USB hub debounce timeout
Overall this set improves reliability of DDR and cache flows,
adds missing USB and MMC features for Agilex5, and refines clock
and configuration handling across platforms.
This patch set has been tested on Agilex 5 devkit, and Agilex devkit.
FIELD_GET() macro is used during EMAC clock source selection
for better code readability and maintainability.
Signed-off-by: Naresh Kumar Ravulapalli <nareshkumar.ravulapalli@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
Fix the incorrect bit masking and bit shift used to compute EMAC
control which in turn is used to select EMAC clock from EMAC
source A or B.
Signed-off-by: Naresh Kumar Ravulapalli <nareshkumar.ravulapalli@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
Update Agilex clock driver to support enabling or disabling
the peripheral clocks via clock driver model APIs.
The caller will pass the clock ID to this driver and the driver
will then proceed to manipulate the desired bit in the Agilex clock
manager peripheral PLL register based on the given clock ID.
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
Following the work done in commit 7f39ad5a ("clk: imx6q: Add definition
for IMX6QDL_CLK_PWM1"), this commit adds definitions for PWM2, PWM3, and
PWM4 clocks. Allowing one to use these PWM modules together with DM_CLK.
Note that the solution was verified only against PWM3.
Signed-off-by: Ricardo Simoes <ricardo.simoes@pt.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
clk_set_rate returns the actual clock rate, When assigned clock rate is
higher than 0x7FFFFFFF, the return value will be recognized as error.
Change to IS_ERR_VALUE to check the return value.
Signed-off-by: Ye Li <ye.li@nxp.com>
Add iMX95 blkctrl clock driver which implements clocks for HSIOMIX
blkctrl and LVDS blkctrl.
Since multiple blkctrl device for different blkctrl may be enabled,
and each has dedicated clock id from 0. We must enable CLK_AUTO_ID
to avoid conflict on clock id.
Signed-off-by: Ye Li <ye.li@nxp.com>
It's common that UARTs are bound and probed before U-Boot relocation,
in which case the clocks of UART and UART's pincontroller must be
registered first. Let's apply DM_FLAG_PRE_RELOC to the driver, allowing
it to bind before relocation.
Signed-off-by: Yao Zi <ziyao@disroot.org>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
