Add include to avoid following build error with imx93_qsb, when
AHAB_BOOT is enabled:
.../arch/arm/mach-imx/ele_ahab.c:262:24: error: 'IMG_CONTAINER_BASE' undeclared (first use in this function); did you mean 'IMG_CONTAINER_END_BASE'?
.../arch/arm/mach-imx/ele_ahab.c:477:20: error: 'FSB_BASE_ADDR' undeclared (first use in this function); did you mean 'WDOG_BASE_ADDR'?
.../arch/arm/mach-imx/ele_ahab.c:543:20: error: 'FSB_BASE_ADDR' undeclared (first use in this function); did you mean 'WDOG_BASE_ADDR'?
Signed-off-by: Niko Mauno <niko.mauno@vaisala.com>
Switch to OF_UPSTREAM to make use of the upstream device trees.
Remove the now obsolete device tree files:
- imx8mn-var-som-symphony.dts
- imx8mn-var-som.dtsi
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
The som-eeprom alias is specific to U-Boot, and not present in upstream
linux imx8mn-var-som device tree.
Add it to the SOM U-Boot specific device tree file in preparation
for migration to OF_UPSTREAM.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Move SOM-specific stuff into a new SOM u-boot.dtsi file.
This way, it can be used by multiple boards.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Rely on serial driver calling clk_enable to enable the lpuart clk, no
need to do init_uart_clk in board_early_init_f().
Also remove board_early_init_f(), because it is empty now.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Rely on serial driver calling clk_enable to enable the lpuart clk, no
need to do init_uart_clk in board_early_init_f().
Also remove board_early_init_f(), because it is empty now.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Rely on serial driver calling clk_enable to enable the lpuart clk, no
need to do init_uart_clk in board_early_init_f().
Also remove board_early_init_f(), because it is empty now.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Select remoteproc related configs for i.MX95 EVK to support manage CM7
using 'rproc' cmd.
Update doc to show details on starting CM7 using rproc cmd.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add i.MX95 CM7 node for remoteproc usage. The dt-bindings for CM7 was
accepted, by the node has not been upstreamed to Linux device tree.
Put the node here to let the driver probe. After Linux upstream repo
has this node landed, the node in imx95-u-boot.dtsi could be removed.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX95 uses System Manager(sm) API to start/stop logical machine or cpu.
There are two modes:
M7 in a dedicated logical machine, use LMM API
M7 and A55 in same logical machine, use CPU API
Extend the driver to using LMM and CPU protocol to manage the M7 core:
- Detect using LMM or CPU API in probe using API scmi_imx_lmm_info().
- Compare linux LM ID(got using scmi_imx_lmm_info) and M7 LM ID(the ID
is fixed as 1 in SM firmware if M7 is in a separate LM),
if Linux LM ID is not same as M7 LM ID(linux and M7 in same LM), use
LMM protocol to start/stop. Whether using CPU or LMM protocol to
start/stop, the M7 status detection could use CPU protocol to detect
started or not. So in imx_rproc_is_running, use scmi_imx_cpu_started to
check the status of M7.
- For above case (2), Use scmi_imx_lmm_power_boot to detect whether
the M7 LM is under control of A55 LM.
- For above case , after using SCMI_IMX_LMM_POWER_ON to check
permission, scmi_imx_lmm_shutdown API should be called to shutdown
the M7 LM.
- Add a new ops imx_rproc_ops_sm.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add a new flag ATT_ECC which indicates the memory region needs ECC
initialization. If the flag is set, clearing the whole memory region to
initialize ECC. If ECC is not initialized, remote core will crash if
directly access the area.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
If i2c_eeprom_size fails, the error value is stored in
variable size and not ret.
Also, this commit fixes printing the error value.
Signed-off-by: Francois Berder <fberder@outlook.fr>
The i.MX91 SoC reuses the ENET FEC from i.MX93. Add all required driver
checks to make it work also on the i.MX91 based platforms.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Enable the 'wget' command and TCP protocol support on all Renesas R-Car
systems. This allows users to download content from local HTTP server,
which may sometimes be more accessible than TFTP server. Enable TCP SACK
support to improve download performance.
The usage is similar to the TFTP command. To download file from server
http://192.ser.ver.ip/file/path/on/local/server , invoke wget as follows:
"
=> wget $loadaddr 192.ser.ver.ip:/file/path/on/local/server
"
In case the HTTP server listens on port other than default port 80,
set the 'httpdstp' environment variable to download file from server
http://192.ser.ver.ip:8088/file/path/on/local/server
"
=> env set httpdstp 8088
=> wget $loadaddr 192.ser.ver.ip:/file/path/on/local/server
"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Pull request efi-2026-04-rc2
CI: https://source.denx.de/u-boot/custodians/u-boot-efi/-/pipelines/29203
Documentation:
* Remove pip from requirements.txt
* develop/process: Clarify name usage in the Signed-off-by line
UEFI:
* Improve EFI variable load message
* Fix use after free in efi_exit() with tcg2
* Fix efi_debug_image_info_normal allocation
* Add missing EFI_CALL in efi_net
Commit d2145a89bc ("net: airoha: bind MDIO controller on Ethernet load")
uses "airoha,en7581-switch" dts node for finding MDIO childs. This is wrong
for EN7523 SoC. The correct node name should be used instead.
Fixes: d2145a89bc ("net: airoha: bind MDIO controller on Ethernet load")
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Add the missing RGMII modes with internal delay for the VSC8541.
Fixes: a5fd13ad19 ("net: phy: MSCC Add Support for VSC8530-VSC8531-VSC8540-VSC8541")
Signed-off-by: Charles Perry <charles.perry@microchip.com>
Commit d2145a89bc ("net: airoha: bind MDIO controller on Ethernet load")
refers to non-present CONFIG_MDIO_MT7531 and non-present "mt7531-mdio"
driver. It should use CONFIG_MDIO_MT7531_MMIO and "mt7531-mdio-mmio"
instead.
Fixes: d2145a89bc ("net: airoha: bind MDIO controller on Ethernet load")
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Multicast and Broadcast Queue Enable and Promiscuous Mode Enable bits
are currently written to "unused" registers using magic values.
Define more of the "unused" MAC regs based on information in the
DesignWare Cores Ethernet Quality-of-Service databook.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
The DesignWare Cores Ethernet Quality-of-Service databook state that
receive and transmit descriptor list address and also transmit and
receive tail pointer registers should be initialized before the receive
and transmit DMAs are started.
It also state to enable the MAC receiver only after the DMA is active.
Otherwise, received frames can fill the Rx FIFO and overflow.
Move the activation of receive and transmit DMA and MAC receiver until
after tail pointer registers have been initialized.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
The DesignWare Cores Ethernet Quality-of-Service databook state that
descriptors up to one location less than the one indicated by the
descriptor tail pointer are owned by the DMA. The DMA continues to
process the descriptors until the following condition occurs:
Current Descriptor Pointer == Descriptor Tail Pointer
The DMA goes into suspend mode when this condition occurs, and updating
the tail pointer resume the DMA processing.
Configure the transmit tail pointer to the first (current) descriptor
pointer so that the tail pointer is a valid address instead of being
initialized to NULL when transmit DMA is started.
Also update the receive tail pointer comment to state that by pointing
to the last descriptor we are actually implying that all receive
descriptors are owned by and can be processed by the DMA.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
The DesignWare Cores Ethernet Quality-of-Service databook state that the
descriptor address from the start to the end of the ring must not cross
the 4GB boundary.
Use lower_32_bits() to write the lower 32 bits of descriptor addresses,
including the 32-bit tail pointers, consistently. No functional change
is intended.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
mdio is a child node of the switch, so to get switch base address
we need to lookup for a parent node
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Currently, the LWIP wget command prints excessive amount of progress
indicator '#' for very long file downloads, limit this to one line
that scales according to transfer size.
The HTTP server does report the size of the entire file in protocol
headers, which are received before the actual data transfer. Cache
this information and use it to adaptively print progress indicator
'#' until it fills one entire line worth of '#', which indicates the
transfer has completed. This way, long transfers don't print pages of
'#', but every transfer will print exactly one line worth of '#'. The
algorithm for '#' printing is the same as TFTP tsize one.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Jerome Forissier <jerome.forissier@rm.com>
The TFTP server can report the size of the entire file that is about to
be received in the Transfer Size Option, this is described in RFC 2349.
This functionality is optional and the server may not report tsize in
case it is not supported.
Always send tsize request to the server to query the transfer size,
and in case the server does respond, cache that information locally
in tftp_state.tsize, otherwise cache size 0. Introduce new function
tftp_client_get_tsize() which returns the cached tftp_state.tsize so
clients can determine the transfer size and use it.
Update net/lwip/tftp.c to make use of tftp_client_get_tsize() and
avoid excessive printing of '#' during TFTP transfers in case the
transfer size is reported by the server.
Submitted upstream: https://savannah.nongnu.org/patch/index.php?item_id=10557
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Jerome Forissier <jerome.forissier@arm.com>
The TFTP transfer size is unsigned integer, update the data type
and print formating string accordingly to prevent an overflow in
case the file size is longer than 2 GiB.
TFTP transfer of a 3 GiB file, before (wrong) and after (right):
Loading: ################################################# 16 EiB
Loading: ################################################## 3 GiB
Signed-off-by: Yuya Hamamachi <yuya.hamamachi.sx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The net_loop() currently conflates return value with file size
at the end of successful transfer, in NETLOOP_SUCCESS state.
The return type of net_loop() is int, which makes this practice
workable for file sizes below 2 GiB, but anything above that will
lead to overflow and bogus negative return value from net_loop().
The return file size is only used by a few sites in the code base,
which can be easily fixed. Change the net_loop() return value to
always be only a return code, in case of error the returned value
is the error code, in case of successful transfer the value is 0
or 1 instead of 0 or net_boot_file_size . This surely always fits
into a signed integer.
By keeping the return code 0 or 1 in case of successful transfer,
no conditionals which depended on the old behavior are broken, but
all the sites had to be inspected and updated accordingly.
Fix the few sites which depend on the file size by making them
directly use the net_boot_file_size variable value. This variable
is accessible to all of those sites already, because they all
include net-common.h .
Signed-off-by: Yuya Hamamachi <yuya.hamamachi.sx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
When building grub-2.12 with a newer GCC, we run in to warings (treated
as errors). The simple fix here is to move to the latest release tag. In
order to build a newer grub from source we need the autoconf-archive
package to be installed.
Signed-off-by: Tom Rini <trini@konsulko.com>
Unmap the sysmem that got mapped by this command.
Use symbolic return value for the command while updating
the return value handling.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The current implementation casts an address to a pointer. Make it more
sandbox-friendly by using map_sysmem().
Use symbolic return value for the command while updating
the return value handling.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The current implementation casts an address to a pointer. Make it more
sandbox-friendly by using map_sysmem().
Convert 'addr' variable to unsigned long, as that is the return type of
hextoul() and address parameter type of map_sysmem().
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
