Allow dynamic configuration of the SPI word length. This is required
for controllers and slaves that need to operate with non-standard
word lengths, such as 9-bit wide transfers.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Simon Glass <simon.glass@canonical.com>
All of these platforms enable CONFIG_BOARD_EARLY_INIT_F and then have a
do-nothing board_early_init_f function. Change to not enabling the
option and so not needing an empty function.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Factorize TAMP_FWU_BOOT_IDX_MASK and TAMP_FWU_BOOT_IDX_OFFSET
definition which are common to STM32MP1 and STM32MP2 SoCs family.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Fix the following errors yielded by Coverity Scan:
CID 644836: Error handling issues (CHECKED_RETURN)
Calling device_chld_unbind without checking return value (as is done elsewhere 6 out of 7 times)
CID 644834: Error handling issues (CHECKED_RETURN)
Calling device_chld_remove without checking return value (as is done elsewhere 4 out of 5 times).
Link: https://lore.kernel.org/r/20260309212331.GF1388590@bill-the-cat/
Fixes: a6d047c0a8 ("video: stm32: remove all child of DSI bridge when its probe failed")
Signed-off-by: Raphael Gallais-Pou <rgallaispou@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Depending of plugged power source (computer, wall charger, ...) it can
happen that we got the following message:
"****************************************************"
"* USB TYPE-C charger not compliant with *"
"* specification *"
"****************************************************"
" "
"### ERROR ### Please RESET the board ### "
This issue has been detected on STM32MP135f-DK board.
It's due to max_uV and min_uV value are initialized at beginning of
board_check_usb_power() and can then be used for the 2 iteration of
adc_measurement().
max_uV/min_uV values issued of the first adc_measurement() iteration
are used as input of the second adc_measurement() iteration, which
can lead to incoherent pair of min_uV/max_uV values.
To ensure that adc_measurement() returns coherent value for max_uV and
min_uV, initialize max_uV and min_uV at each loop start.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Kory Maincent <kory.maincent@bootlin.com>
Balaji Selvanathan <balaji.selvanathan@oss.qualcomm.com> says:
This series replaces the SYNC_CACHE approach with FUA (Force Unit
Access) to prevent data loss during board resets while avoiding
system hangs during large sparse image flashing operations.
The previous SYNC_CACHE implementation caused timeouts and hangs
when flashing large sparse images because it issued cache sync
commands after every write operation. The FUA approach achieves
the same data integrity goal by setting the FUA bit in
WRITE10 commands.
Link: https://lore.kernel.org/r/20260416-enable_fua-v3-0-84508de2bfd9@oss.qualcomm.com
Enable the Force Unit Access (FUA) bit in SCSI WRITE10 commands to
ensure writes bypass the device's volatile cache and go directly to
non-volatile storage. This provides write-through behavior that prevents
data loss during board resets.
Reviewed-by: Varadarajan Narayanan <varadarajan.narayanan@oss.qualcomm.com>
Signed-off-by: Aswin Murugan <aswin.murugan@oss.qualcomm.com>
Signed-off-by: Balaji Selvanathan <balaji.selvanathan@oss.qualcomm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
While the SYNC_CACHE approach prevents data loss during board resets,
it causes system hangs during large sparse image flashing operations.
This will be replaced with a FUA (Force Unit Access) approach in future
commit, which achieves the same data integrity goal more efficiently.
This reverts commit ffe4e6ab42.
Signed-off-by: Balaji Selvanathan <balaji.selvanathan@oss.qualcomm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Quentin Schulz <foss+uboot@0leil.net> says:
This migrates the net options away from the main Kconfig to net/Kconfig,
rename the current NET option to NET_LEGACY to really highlight what it
is and hopefully encourage more people to use lwIP, add a new NET
menuconfig (but keep NO_NET as an alias to NET=n for now) which then
allows us to replace all the "if legacy_stack || lwip_stack" checks with
"if net_support" which is easier to read and maintain.
The only doubt I have is wrt SYS_RX_ETH_BUFFER which seems to be needed
for now even when no network is configured? Likely due to
include/net-common.h with PKTBUFSRX?
No change in behavior is intended. Only change in defconfig including
other defconfigs where NO_NET=y or NET is not set, in which case NO_NET
is not set or NET=y should be set in the top defconfig. Similar change
required for config fragments. See commit log in patch adding NET
menuconfig for details.
This was tested based on 70fd0c3bb7 ("x86: there is no
CONFIG_UBOOT_ROMSIZE_KB_12288"), from within the GitLab CI container
trini/u-boot-gitlab-ci-runner:noble-20251013-23Jan2026 and set up
similarly as in "build all platforms in a single job" GitLab CI job.
#!/usr/bin/env bash
set -o pipefail
set -eux
ARGS="-BvelPEWM --reproducible-builds --step 0"
./tools/buildman/buildman -o ${O} --force-build $ARGS -CE $*
./tools/buildman/buildman -o ${O} $ARGS -Ssd $*
O=../build/u-boot/ ../u-boot.sh -b master^..b4/net-kconfig |& tee ../log.txt
I can't really decipher the log.txt, but there's no line starting with
+ which would be an error according to tools/buildman/builder.py help
text. Additionally, because I started the script with set -e set and
because buildman has an exit code != 0 when it fails to build a board,
and I have the summary printed (which is the second buildman call), I
believe it means all builds passed.
The summary is the following:
aarch64: (for 537/537 boards) all +0.0 rodata +0.0
uniphier_v8 : all +1 rodata +1
u-boot: add: 0/0, grow: 1/0 bytes: 1/0 (1)
function old new delta
data_gz 10640 10641 +1
arm: (for 733/733 boards) all -0.0 rodata -0.0
uniphier_v7 : all -1 rodata -1
u-boot: add: 0/0, grow: 0/-1 bytes: 0/-1 (-1)
function old new delta
data_gz 11919 11918 -1
opos6uldev : all -3 rodata -3
u-boot: add: 0/0, grow: 0/-1 bytes: 0/-3 (-3)
function old new delta
data_gz 18778 18775 -3
uniphier_ld4_sld8: all -3 rodata -3
u-boot: add: 0/0, grow: 0/-1 bytes: 0/-3 (-3)
function old new delta
data_gz 11276 11273 -3
stemmy : all -20 rodata -20
u-boot: add: 0/0, grow: 0/-1 bytes: 0/-20 (-20)
function old new delta
data_gz 15783 15763 -20
As far as I could tell this data_gz is an automatically generated array
when CONFIG_CMD_CONFIG is enabled. It is the compressed .config stored
in binary form. Because I'm changing the name of symbols, replacing a
menu with a menuconfig, additional text makes it to .config and the
"# Networking" section in .config disappears.
Here is the diff for the 5 defconfigs listed above, generated with:
for f in build/*-m; do
diff --unified=0 $f/.config $(dirname $f)/$(basename -a -s '-m' $f)/.config
done
(-m is the build directory for master, and without the suffix, it's the
top commit of this series)
"""
--- build/opos6uldev-m/.config 2026-04-20 10:53:49.804528526 +0200
+++ build/opos6uldev/.config 2026-04-20 11:03:37.430242767 +0200
@@ -970,4 +969,0 @@
-
-#
-# Networking
-#
@@ -975,0 +972 @@
+CONFIG_NET_LEGACY=y
--- build/stemmy-m/.config 2026-04-20 11:01:33.653698123 +0200
+++ build/stemmy/.config 2026-04-20 11:04:53.452577311 +0200
@@ -733,4 +732,0 @@
-
-#
-# Networking
-#
@@ -738,2 +733,0 @@
-# CONFIG_NET is not set
-# CONFIG_NET_LWIP is not set
--- build/uniphier_ld4_sld8-m/.config 2026-04-20 11:00:41.605469071 +0200
+++ build/uniphier_ld4_sld8/.config 2026-04-20 11:04:22.226439899 +0200
@@ -997,4 +996,0 @@
-
-#
-# Networking
-#
@@ -1002,0 +999 @@
+CONFIG_NET_LEGACY=y
--- build/uniphier_v7-m/.config 2026-04-20 10:53:04.019307319 +0200
+++ build/uniphier_v7/.config 2026-04-20 11:03:01.688085486 +0200
@@ -1004,4 +1003,0 @@
-
-#
-# Networking
-#
@@ -1009,0 +1006 @@
+CONFIG_NET_LEGACY=y
--- build/uniphier_v8-m/.config 2026-04-20 10:43:05.614441175 +0200
+++ build/uniphier_v8/.config 2026-04-20 10:41:03.214852130 +0200
@@ -875,4 +874,0 @@
-
-#
-# Networking
-#
@@ -880,0 +877 @@
+CONFIG_NET_LEGACY=y
"""
This is fine:
- Networking menu doesn't exist anymore so "#\n# Networking\n#\n" won't
be in .config anymore.
- opos6uldev, uniphier_ld4_sld8, uniphier_v7 and uniphier_v8 all have
(old) CONFIG_NET enabled, (new) CONFIG_NET will still be set but
CONFIG_NET_LEGACY also needs to be defined now to reflect the stack
choice (even if default),
- stemmy has CONFIG_NO_NET set, which means CONFIG_NET and
CONFIG_NET_LWIP are not reachable anymore hence why they don't need to
be part of .config,
GitLab CI was run on this series (well, not exactly, but it's only
changes to the git logs that were made):
https://source.denx.de/u-boot/contributors/qschulz/u-boot/-/pipelines/29849
It passes.
Link: https://lore.kernel.org/r/20260420-net-kconfig-v1-0-9900002d8e72@cherry.de
NO_NET is now a transitional symbol which may eventually be removed. Its
meaning is the opposite of the new meaning of NET (that is, any
networking stack).
Update the symbol dependency by using NET instead of !NO_NET.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
TPL_NET symbol never existed in the first place, so let's remove this
misleading piece of documentation.
Fixes: 143c9a7e9d ("doc: describe TPL/VPL/SPL boot")
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Since the move to make NET a menuconfig and NO_NET a synonym of NET=n,
when NET is enabled, NET_LEGACY || NET_LWIP is necessarily true, so
let's simplify the various checks across the codebase.
SPL_NET_LWIP doesn't exist but SPL_NET_LEGACY is an alias for SPL_NET so
the proper symbol is still defined in SPL whenever needed.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This will allow a bunch of simplifications across the code base.
Disabling NET is the equivalent of today's NO_NET choice. This means
that if NET is enabled, either the legacy or lwIP stack is necessarily
selected, which allows us to simplify if NET_LEGACY || NET_LWIP into
if NET in a later commit.
Config fragments - or defconfigs including other defconfigs - setting
the network stack (NET_LEGACY or NET_LWIP) must also set NET (or unset
NO_NET) if the config they apply to - or the included defconfigs -
unsets NET (or selects NO_NET) as otherwise the NET_LEGACY and NET_LWIP
symbols are unreachable. This is the case for the two defconfig modified
in this commit.
NO_NET is now a convenience symbol which hides NET entirely to avoid
modifying many defconfigs. If one selected NO_NET to disable the
networking stack in the past, this will still work for now. Technically,
we should be using the "transitional" Kconfig attribute but that is only
available since Kconfig from Linux kernel v6.18 and we're on 6.1 right
now.
Note that this moves CONFIG_SYS_RX_ETH_BUFFER from under the Network
menu back into the main menu as it seems like it needs to be defined
even when there's no need for NET support at all and menuconfig option
doesn't work the same way as a menu.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Highlight that NET really is the legacy networking stack by renaming the
option to NET_LEGACY.
This requires us to add an SPL_NET_LEGACY alias to SPL_NET as otherwise
CONFIG_IS_ENABLED(NET_LEGACY) will not work for SPL.
The "depends on !NET_LWIP" for SPL_NET clearly highlights that it is
using the legacy networking app so this seems fine to do.
This also has the benefit of removing potential confusion on NET being a
specific networking stack instead of "any" network stack.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
In the main Kconfig, there are only two more menus, General Setup and
Expert, in addition to the net menu. Since the part in the main Kconfig
is mostly about selecting the network stack (legacy or lwIP), and that
we already have a net/Kconfig, let's move those to net/Kconfig to have
everything in the same place.
No intended change in behavior.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The hardware configuration pins are used both to select the DDR
configuration and to determine the installed memory size.
On Aquila AM69, the DDR timing patch is applied in the R5 SPL, while the
memory size fixup for the next-stage U-Boot DT is done later in the A72
SPL path.
The previous immplementation was not taking in account that the hw_cfg
value is lost both during SPL execution (board_init_f and board_init_r)
and between SPL and U-Boot proper.
Fix this by reading the hardware configuration pins when the memory size
is actually needed:
- in the R5 SPL, to select the correct DDR configuration
- in the A72 SPL, to fix up the U-Boot DT memory size and bank layout
Fixes: 3f0528882c ("board: toradex: add aquila am69 support")
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Acked-by: Francesco Dolcini <francesco.dolcini@toradex.com>
The 16GB dual-rank DDR configuration uses an incorrect DDRSS_PLL_FHS_CNT
value. This makes DDR initialization hang during the DDR frequency
handshake sequence.
Update DDRSS_PLL_FHS_CNT to the correct value for the 16GB dual-rank
configuration.
Fixes: 39e014f43a ("board: toradex: aquila-am69: Add support for 16GB dual rank memory configuration")
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Acked-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Some use cases require remoteproc firmware to be loaded before Linux
boots. Introduce rprocsemmcboot and rproc_fw_binaries to load the
remoteproc cores from U-Boot, relying on the TI k3_rproc framework
which already handles the secure firmware variants, firmware loading,
and proper initialization.
The firmware binaries are expected to be present in the eMMC rootfs
under /lib/firmware/.
To activate, run rprocsemmcboot or add it to bootcmd:
bootcmd=run rprocsemmcboot; bootflow scan -b
The upstream U-Boot does not yet have the remoteproc DT nodes enabled
for the Aquila AM69, making firmware loading fail. Marking as pending
waiting for remoteproc enabling, which could happen along with the
OF_UPSTREAM migration.
Signed-off-by: Vitor Soares <vitor.soares@toradex.com>
Acked-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Enable CONFIG_OF_UPSTREAM to receive automatic
device tree updates for the Aquila AM69.
Remove the now-obsolete device tree files:
- arch/arm/dts/k3-am69-aquila-dev.dts
- arch/arm/dts/k3-am69-aquila.dtsi
Signed-off-by: Ernest Van Hoecke <ernest.vanhoecke@toradex.com>
Acked-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Some virtio implementations may forward the virtio requests directly to
the underlying hw. The hw may have some restrictions in how many and how
big the requests can be. Therefore, the corresponding virtio device will
announce this limitations with the SIZE_MAX & SEG_MAX feature.
Add support for those features. Split an io request into multiple virtio
requests if more than seg_max segments would be used. Also split a
single buffer request into multiple segments if the buffer is bigger
then size_max.
Signed-off-by: Christian Pötzsch <christian.poetzsch@kernkonzept.com>
Signed-off-by: Adam Lackorzynski <adam@l4re.org>
Currently the implementation does not just skip all devices beside
device 0, it also skips all functions (besides 0) on device 0. This
broke basically all AMD platforms, since they have a lot of internal SOC
devices behind these functions.
This was detected, because the XHCI controller and therefore the USB
devices were not found by u-boot on AMD/crater platform.
PCI_MASK_BUS() returns both device and function bits, so it skips any
bdf where either device > 0 or function > 0. Using PCI_DEV() extracts
only the device number, matching the intent in only_one_child().
It therefore now checks all functions on device 0 (Linux does the same).
I build tested u-boot as coreboot payload and run it on a recent x86 AMD
platform. Devices like the XHCI controller are now found again.
Fixes: fbde868ba4 ("pci: skip unnecessary PCIe scanning")
Signed-off-by: Maximilian Brune <maximilian.brune@9elements.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
CC: Tom Rini <trini@konsulko.com>
CC: Andrew Goodbody <andrew.goodbody@linaro.org>
CC: George McCollister <george.mccollister@konsulko.com>
CC: Simon Glass <sjg@chromium.org>
Raymond Mao <raymond.mao@linaro.org> says:
The series include refactoring on bloblist and fdtdec to support handoff
of multiple DT overlays and applying them into the DT base during setup.
All changes are aligned to the spec update for supporting DT overlay
handoff[1].
Notes for testing:
Currently DT overlay is not yet enabled in TF-A, but with the test
patches I provided for TF-A and OP-TEE build, importing a DT overlay
blob file from QEMU to TF-A reserved memory is supported.
Follow below instructions to build and run for test:
$ repo init -u https://github.com/OP-TEE/manifest.git -m qemu_v8.xml
Replace your local qemu_v8.xml with [2], which contains all necessary
changes in both TF-A and OP-TEE build.
$ repo sync
$ cd build
$ make toolchains
$ make ARM_FIRMWARE_HANDOFF=y all
Copy and rename your DT overlay blob as 'qemu_v8.dtb' into out/bin
$ make ARM_FIRMWARE_HANDOFF=y run-only
[1] Add Transfer Entry for Devicetree Overlay
https://github.com/FirmwareHandoff/firmware_handoff/pull/74
[2] https://github.com/raymo200915/optee_manifest/blob/dt_overlay_handoff/qemu_v8.xml
Link: https://lore.kernel.org/r/20250718141621.3147633-1-raymond.mao@linaro.org
Select OF_LIBFDT_OVERLAY for qemu_arm64 and vexpress_fvp_bloblist
to hand over DTO via bloblist.
Signed-off-by: Raymond Mao <raymond.mao@linaro.org>
Tested-by: Michal Simek <michal.simek@amd.com>
During FDT setup, apply all existing DT overlays from the bloblist
to the base FDT if bloblist is being used for handoff from previous
boot stage.
According to the Firmware Handoff spec update to support DT overlay [1],
an overlay must have the same top-level compatible string as its target
base DT has.
Before applying the overlays, check whether sufficient space is
reserved in the base DT blob, if not, resize the blob to the allowed
padded size, which is limited by CONFIG_SYS_FDT_PAD and the bloblist
spare space size.
After all overlays are applied, resize the merged DT to its actual size.
[1] Add Transfer Entry for Devicetree Overlay
https://github.com/FirmwareHandoff/firmware_handoff/pull/74
Signed-off-by: Raymond Mao <raymond.mao@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Michal Simek <michal.simek@amd.com>
Add an API to search for the blobs with specified tag and use the
hook function to apply the blob data.
Add a helper function to return the inline header size as according
to recent spec[1] updates, the actual data can be following an inline
header instead of following the TE header immediately.
[1] Firmware Handoff spec:
https://github.com/FirmwareHandoff/firmware_handoff
Signed-off-by: Raymond Mao <raymond.mao@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Michal Simek <michal.simek@amd.com>
It causes a panic when blob is shrunk and 'new_alloced' is less than
'next_ofs'. The data area that needs to be moved should end up at
'hdr->used_size'.
Fixes: 1fe5937549 ("bloblist: Support resizing a blob")
Signed-off-by: Raymond Mao <raymond.mao@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Michal Simek <michal.simek@amd.com>
Add two helper functions for:
1. marking a blob void
2. getting blob record from a given blob data pointer.
Signed-off-by: Raymond Mao <raymond.mao@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Michal Simek <michal.simek@amd.com>
Various Qualcomm additions this cycle:
* USB superspeed support for 1 platform
* Initial support for the Milos platform and the Fairphone Gen 6
(chainloaded from ABL)
* Improved support for booting with OP-TEE on supported platforms
* Initial basic power domain support
Notably there is a generic change to the device core, missing power
domains will no longer cause a device to fail probe and instead will
just print a warning. This shouldn't affect any existing platforms.
Qualcomm platforms rely on the kernel to manage specialized reboot modes
such as EDL, bootloader entry, and other vendor-specific reset flows.
Allowing U-Boot to override these via EFI runtime reset services leads to
incorrect behavior when the kernel issues advanced reboot requests.
Now that EFI_HAVE_RUNTIME_RESET is exposed as a user-configurable Kconfig
option, disable it for qcom_defconfig so that the kernel retains full
control over reboot handling on Qualcomm SoCs.
This ensures that EFI runtime reboot callbacks are not registered on
these platforms, preventing conflicts with kernel-managed PSCI reset
paths.
Signed-off-by: Aswin Murugan <aswin.murugan@oss.qualcomm.com>
Reviewed-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Acked-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Link: https://patch.msgid.link/20260324175913.92858-3-aswinm@qti.qualcomm.com
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
Expose EFI_HAVE_RUNTIME_RESET as a proper Kconfig boolean with a prompt
so platforms can explicitly enable or disable advertising the EFI reset
runtime service.
The current PSCI-based EFI runtime reset implementation is always
enabled whenever CONFIG_PSCI_RESET is selected, but it does not support
passing the additional arguments required for specialized reset modes.
As a result, reboot requests such as bootloader mode or EDL mode cannot
be propagated correctly and instead fall back to a normal reboot.
By making EFI_HAVE_RUNTIME_RESET user-configurable, platforms that
depend on extended PSCI reset can now explicitly disable EFI runtime
reset handling even when CONFIG_PSCI_RESET is enabled, ensuring
that the kernel retains full control of advanced reboot paths.
Default behavior for existing platforms remains unchanged.
Signed-off-by: Aswin Murugan <aswin.murugan@oss.qualcomm.com>
Reviewed-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Link: https://patch.msgid.link/20260324175913.92858-2-aswinm@qti.qualcomm.com
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
Remove the USB controller dr_mode override from the u-boot device
tree. The upstream Linux device tree already configures the USB
controller with dr_mode = "otg", which supports both host and
peripheral modes including fastboot.
The previous override to "host" mode prevented fastboot from working
as it requires peripheral mode support. By removing this override,
the upstream OTG configuration is inherited, enabling fastboot while
maintaining host mode capability through the usb-role-switch
property.
Signed-off-by: Balaji Selvanathan <balaji.selvanathan@oss.qualcomm.com>
Link: https://patch.msgid.link/20260324-kodiak_dts-v2-1-243c28a3ffb9@oss.qualcomm.com
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
Add support for OP-TEE live tree DT fixup support which enables U-Boot
OP-TEE driver to be probed. As well as the EFI DT fixup protocol allows
the live tree fixup to be carried over to the OS for the OP-TEE driver
in the OS to probe as well.
Note that this fixup only gets applied if OP-TEE support is detected via
checking for OP-TEE message UID.
Signed-off-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Link: https://patch.msgid.link/20260127062341.723966-3-sumit.garg@kernel.org
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
OP-TEE message UID check API can be useful to know whether OP-TEE
is enabled on not assuming the corresponding SMC call is properly
handled if OP-TEE is not supported.
This API can be used by platform code to know OP-TEE presence and
on that basis OP-TEE DT node can be added as part of DT fixups for
the OP-TEE driver probe to happen for both U-Boot and Linux.
Signed-off-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Reviewed-by: Casey Connolly <casey.connolly@linaro.org>
Link: https://patch.msgid.link/20260127062341.723966-2-sumit.garg@kernel.org
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
