tshsl_ns is the clock delay for chip select deassert. This is the delay in
master reference clocks for the length that the master mode chip select
outputs are de-asserted between transactions.
The minimum delay is always SCLK period to ensure the chip select is never
re-asserted within one SCLK period.
That is why tshsl_ns delay should be at least one sclk_ns value. If it is
less than sclk_ns, set it equal to sclk_ns.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20250702065717.3871435-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Starting from 'commit <8077d296adff> ("spi: cadence-quadspi: Use STIG
mode for all ops with small payload") the utilization of STIG mode
has been implemented for read and write operations involving less
than 8 bytes of data.
However, following this commit, encountering timeout issues occurs when
writing odd bytes of data in DDR mode, as indicated below:
"jedec_spi_nor flash@0: flash operation timed out
SF: 3 bytes @ 0x0 Written: ERROR -110"
To resolve this issue, the number of bytes to write has been updated
specifically for DDR mode.
Signed-off-by: Tejas Bhumkar <tejas.arvind.bhumkar@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20250704040444.671604-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The clock driver fails to correctly calculate the PLL clock
rate for peripherals when using the DPLL as the clock source.
The DPLL operates within the full power domain, while peripheral
clocks reside in the low power domain. To ensure accurate PLL
clock rate computation when the peripheral clock source is set
to DPLL, the DPLL-to-LPD cross divisor is used.
Signed-off-by: Padmarao Begari <padmarao.begari@amd.com>
Link: https://lore.kernel.org/r/20250618094329.296731-1-padmarao.begari@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The cache driver here can only build on RISCV due to header
dependencies. Express that requirement in Kconfig as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The SoC pads of TH1520 are separated into three groups (AP 1, AP 2 and
AON) controlled by independent pin controllers. This patch ports their
driver from Linux kernel with most code for setting pinconf and pinmux
kept as is.
The dt-binding of TH1520 pin controller uses a schema where pins to
configure are specfied as strings and looked up at runtime, which the
generic pinctrl helpers of U-Boot cannot parse, thus a customized
set_state() callback is implemented to parse pinconfig nodes and setup
the configuration.
Signed-off-by: Yao Zi <ziyao@disroot.org>
Acked-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Update the MMC driver to retrieve the clock manager base address via
probing the clock manager node in the device tree.
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This reverts commit ae93d8106b.
It is no longer needed since 24b1e0c7e2.
Since the obsolete include pulled in byteorder.h which is needed by now,
include this one directly.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The commit e8a9521e64
("vf500/vf610: synchronise device trees with linux")
has synchronized U-Boot's DTS with v5.19 Linux kernel.
It turned out that in Linux's upstream iomuxc node description the
'fsl,mux_mask' was missing, so the U-Boot's pinctrl driver for NXP's
Vybrid SoC was not working properly.
As by default the mux mask was set to 0, for example the vf610 based
boards (like BK4) were bricked, due to misconfiguration of gpio at
early boot stage.
The fix for all NXP eligible boards is to define .mux_mask field for
soc specific *pinctrl_soc_info structure and use it directly in pinctrl
MMIO driver, without the need to read the "fsl,mux_mask" property from
device tree.
This change brings the NXP's pinctrl driver in U-Boot closer to Linux
upstream one.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com> #for i.MX8ULP
Ilias Apalodimas <ilias.apalodimas@linaro.org> says:
Instructions that lead ito an exception in the hypervisor can't modify two
CPU registers at once for the ARM ISA.
These instructions cannot be emulated by KVM as they do not produce
syndrome information data that KVM can use to infer the destination
register, the faulting address, whether it was a load or store, or
if it's a 32 or 64 bit general-purpose register.
As a result an external abort is injected from QEMU, via ext_dabt_pending.
Link: https://lore.kernel.org/r/20250618065828.1312146-1-ilias.apalodimas@linaro.org
A following patch is replacing our IO accessors with
do { ... } while(0) ones in order to make them usable with KVM.
That leads to an error eventually looking like this:
arch/arm/include/asm/io.h:62:9: error: expected expression before 'do'
62 | do { \
| ^~
arch/arm/include/asm/io.h:211:41: note: in expansion of macro '__raw_writel'
211 | #define out_arch(type,endian,a,v) __raw_write##type(cpu_to_##endian(v),a)
| ^~~~~~~~~~~
arch/arm/include/asm/io.h:223:25: note: in expansion of macro 'out_arch'
223 | #define out_be32(a,v) out_arch(l,be32,a,v)
| ^~~~~~~~
drivers/spi/fsl_dspi.c:127:17: note: in expansion of macro 'out_be32'
127 | out_be32(addr, val) : out_le32(addr, val);
| ^~~~~~~~
So adjust the current macros and code to be compatible with the upcoming
change.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add R-Car Gen4 PCIe controller support for host mode.
This controller is based on Synopsys DesignWare PCIe. However, this
particular controller has a number of vendor-specific registers, and as
such, requires initialization code, including PHY firmware loading.
The PHY firmware loading is implemented in an entirely generic manner,
by calling a firmware loading script, which the user can configure in
a way they require. This provides the user with flexibility of loading
the PCIe firmware from whichever storage device they need to load it
from.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Use dw_pcie_link_set_max_link_width() instead of local implementation
of the same functionality. This does change the behavior slightly, as
the dw_pcie_link_set_max_link_width() implementation also programs the
LNKCAP register MLW, this should however be correct and is now aligned
with Linux kernel behavior.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Use dw_pcie_link_set_max_link_width() instead of local implementation
of the same functionality. This does change the behavior slightly, as
the dw_pcie_link_set_max_link_width() implementation also programs the
LNKCAP register MLW, this should however be correct and is now aligned
with Linux kernel behavior.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Add dw_pcie_link_set_max_link_width() implementation ported from Linux kernel
as of commit 89db0793c9f2 ("PCI: dwc: Add missing PCI_EXP_LNKCAP_MLW handling").
This is common code which is already duplicated in multiple drivers.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Hrushikesh Salunke <h-salunke@ti.com> says:
This series adds support for the Endpoint mode on Cadence PCIe controller
on TI's K3 family of SoCs. The driver is an adaptation of the Linux
driver (drivers/pci/controller/cadence/pci-j721e.c) and has been
implemented specifically for Endpoint mode of operation on AM64X. A minor
set of changes will be sufficient to support other K3 SoCs as well.
This patch is tested on AM64X EVM. Following are the log corresponding
to this feature.
https://gist.github.com/hrushikesh221/e8557cbe7667877c50f7d7e9bb96d060
Link: https://lore.kernel.org/r/20250616164929.631791-1-h-salunke@ti.com
Add support for Endpoint mode of operation in the Cadence PCIe
Controller present on TI's K3 SoCs. This driver is an adaptation of the
Linux kernel v6.15 driver (drivers/pci/controller/cadence/pci-j721e.c).
Signed-off-by: Hrushikesh Salunke <h-salunke@ti.com>
This is a port of the corresponding commit in the Linux kernel which
adds the same support for the Cadence Torrent driver[0]. The commit
message below is taken as-is from the Linux kernel commit being ported.
The Torrent SERDES can support at most two different protocols (PHY types).
This only mandates that the device-tree sub-nodes used to represent the
configuration should describe links with at-most two different protocols.
The existing implementation however imposes an artificial constraint that
allows only two links (device-tree sub-nodes). As long as at-most two
protocols are chosen, using more than two links to describe them in an
alternating configuration is still a valid configuration of the Torrent
SERDES.
A 3-Link 2-Protocol configuration of the 4-Lane SERDES can be:
Lane 0 => Protocol 1 => Link 1
Lane 1 => Protocol 1 => Link 1
Lane 2 => Protocol 2 => Link 2
Lane 3 => Protocol 1 => Link 3
A 4-Link 2-Protocol configuration of the 4-Lane SERDES can be:
Lane 0 => Protocol 1 => Link 1
Lane 1 => Protocol 2 => Link 2
Lane 2 => Protocol 1 => Link 3
Lane 3 => Protocol 2 => Link 4
[0] 5b7b83a983
Signed-off-by: Hrushikesh Salunke <h-salunke@ti.com>
Observing the crash when we add the i2c-arbitrator node in the device
tree as per the DT bindings. The issue is with the child node of
i2c-arbitrator@72 i.e., i2c@f1950000->i2c-arbitrator@72->i2c-arb, as the
arbitrator uses the uclass of mux(UCLASS_I2C_MUX) and the mux uclass driver
checks for the "reg" property using the i2c_mux_child_post_bind() function,
if it won't find the "reg" property it will return -EINVAL which is leading
to the crash.
So, add the logic to check whether the child node has the "reg" property,
if the "reg" property exists then read the "reg" and update the channel.
https://www.kernel.org/doc/Documentation/devicetree/bindings/i2c/i2c-arb.txt
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This PR introduces 3 new platforms, two from the new Dragonwing IQx
series (QCS615 and QCS8300) as well as the IPQ5424.
Additionally:
* Support for booting downstream Android boot images on some phones is
added
* Capsule update support is expanded to be more generic, determining
which partition U-Boot was flashed to automatically and supporting
many more boards.
* Minor capsule update bugs are fixed
* A watchdog driver is added and gets timeout support
* Autoboot now requires pressing "space" specifically to stop booting as
a workaround for some boards getting rogue key presses which would
cause autoboot to fail
* Documentation is added for the Dragonwing boards
* The RB1/2 now use USB gadget mode rather than host
* A bug is fixed where GPIO reads could return incorrect values
Device bus address might not be valid for direct access when the bus
address and CPU address are not the same. Use dev_bus_to_phys() to
translate bus address back to CPU address.
Fixes: 3d98b8c504 ("net: designware: Invalidate RX buffer cache before freeing the DMA descriptor")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Rename the variable and add ENV_ prefix, so that all configuration
options which are related to environment would have an CONFIG_ENV_
prefix. No functional change.
Use ENV_MMC_DEVICE_INDEX to clarify this is the SD/MMC device
index, a number, as enumerated by U-Boot. Update the help text
accordingly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
First set of u-boot-at91 features for the 2025.10 cycle:
This feature set includes the addition of new sam9x7 SoC and a new board
named sam9x7-curiosity. There is also new support for sam9x60 compatible
at91 watchdog.
Add PMC driver support for sam9x7 SoC family
Signed-off-by: Varshini Rajendran <varshini.rajendran@microchip.com>
[balamanikandan.gunasundar@microchip.com: Add peripheral clock id for pmecc]
Signed-off-by: Balamanikandan Gunasundar <balamanikandan.gunasundar@microchip.com>
The clk_register function logs an error if parent_name is missing from the
Device Tree.On the SAM9X7, the main_rc node is omitted to stay aligned with
the Linux Device Tree.Remove the parent_name check in at91_clk_main_rc()
to allow it to pass NULL when the parent is not specified.
Signed-off-by: Manikandan Muralidharan <manikandan.m@microchip.com>
