This patch renames the board directory from board/freescale to
board/nxp because NXP now provides Board Support Packages (BSPs) and
tools for the former Freescale i.MX and other i.MX products.
All relevant references have been updated accordingly. This change does
not affect functionality.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The X96Q is a set-top box with an H313 SoC, AXP305 PMIC, 1 or 2 GiB RAM,
8 or 16 GiB eMMC flash, 2x USB A, Micro-SD, HDMI, Ethernet, audio/video
output, and infrared input.
https://x96mini.com/products/x96q-tv-box-android-10-set-top-box
This commit adds a defconfig and some documentation. The devicetree is
already in dts/upstream.
The CONFIG_DRAM_SUNXI_* settings are chosen such that the register
values in the DRAM PHY's MMIO space are as close as possible to those
observed when booting with the preinstalled vendor U-Boot. The DRAM
clock frequency of 600 MHz was reported in the vendor U-Boot's output.
Signed-off-by: J. Neuschäfer <j.ne@posteo.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
When CONFIG_OF_UPSTREAM is enabled, the device tree name provided by SPL
already includes the vendor directory (e.g., "allwinner/board-name").
The existing logic in misc_init_r() unconditionally prepends "allwinner/"
for ARM64 builds, resulting in an incorrect path like
"allwinner/allwinner/board-name.dtb".
This patch modifies the logic to only prepend the vendor prefix if
CONFIG_OF_UPSTREAM is NOT enabled. This ensures compatibility with both
legacy builds and the new upstream devicetree structure.
Signed-off-by: Bohdan Chubuk <chbgdn@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Greg Malysa <malysagreg@gmail.com> says:
This series adds the final pieces to enable mainline U-Boot to build and
boot all Analog Devices SC5xx SoCs and supports the associated carrier
board options. At this point it should be viable for new users for these
platforms to start with the latest version of U-Boot rather than our
vendor fork, however some features (such as OSPI support and falcon
boot) remain unavailable until we are able to unify our implementations
with the mainline implementations.
Link: https://lore.kernel.org/r/20251211080414.5363-1-malysagreg@gmail.com
[trini: Rebuild CI containers to have new tools]
Signed-off-by: Tom Rini <trini@konsulko.com>
This adds support for the Analog Devices SC598-SOM and configurations
for using it with both the SOMCRR-EZKIT and SOMCRR-EZLITE. This adds
dtsis for both Rev D (including older revisions) and Rev E SOMs, which
are not compatible due to BOM changes. Although no new Rev D SOMs are
produced as of 2025, many are in circulation, so the RevD dtsi is
included to facilitate use for existing customers.
Signed-off-by: Vasileios Bimpikas <vasileios.bimpikas@analog.com>
Signed-off-by: Utsav Agarwal <utsav.agarwal@analog.com>
Signed-off-by: Arturs Artamonovs <arturs.artamonovs@analog.com>
Signed-off-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Signed-off-by: Caleb Ethridge <caleb.ethridge@analog.com>
Signed-off-by: Philip Molloy <philip@philipmolloy.com>
Signed-off-by: Greg Malysa <malysagreg@gmail.com>
PHYTEC maintains an actively monitored mailing list for upstream
activities: upstream@lists.phytec.de. Add it to the MAINTAINERS
entries for PHYTEC boards we actively develop and contribute to.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Acked-by: Teresa Remmet <t.remmet@phytec.de>
Tom Rini <trini@konsulko.com> says:
This series builds on top of what Beleswar Padhi did in [1]. While
there's still discussion about the mkimage related parts, the linker
portion appears to the reliable path forward. An alternative that I had
mentioned before, and was part of previous discussions on this topic[2]
is in the end I believe not reliable enough. While we can take an output
file and pad it to where we think it needs to be, ultimately the linker
needs to place the symbol where we want it and if that isn't where we
pad to, we have a different problem. So what this series does (but each
commit message elaborates on the arch-specific linker scripts being
inconsistent) is make sure the linker script will place the required
symbol at 8-byte alignment, and then also use an ASSERT to fail the
build if this would not be true due to some unforseen event.
[1]: https://lore.kernel.org/u-boot/20260112101102.1417970-1-b-padhi@ti.com/
[2]: https://source.denx.de/u-boot/u-boot/-/issues/30
Link: https://lore.kernel.org/r/20260115222828.3931345-1-trini@konsulko.com
With commit 0535e46d55 ("scripts/dtc: Update to upstream version
v1.7.2-35-g52f07dcca47c") it is now a fatal error to U-Boot if our
device tree is not 8-byte aligned. In commit 85f586035d ("ARM: OMAP2+:
Pad SPL binary to 8-byte alignment before DTB") Beleswar Padhi explains
that we must have ALIGN(x) statements inside of a section to ensure that
padding is included and not simply that the linker address counter is
incremented. To that end, this patch:
- Aligns the final section before _end by 8-bytes by adding '. =
ALIGN(8);' or changing an existing ALIGN(4) statement.
- Ensure that we do have alignment by adding an ASSERT so that when not
aligned we fail to link (and explain why).
Signed-off-by: Tom Rini <trini@konsulko.com>
With commit 0535e46d55 ("scripts/dtc: Update to upstream version
v1.7.2-35-g52f07dcca47c") it is now a fatal error to U-Boot if our
device tree is not 8-byte aligned. In commit 85f586035d ("ARM: OMAP2+:
Pad SPL binary to 8-byte alignment before DTB") Beleswar Padhi explains
that we must have ALIGN(x) statements inside of a section to ensure that
padding is included and not simply that the linker address counter is
incremented. To that end, this patch:
- Expands some linker sections to be more readable when adding a second
statement to the section.
- Aligns the final section before _end (for U-Boot) or
_image_binary_end or __bss_end (for xPL phases) by 8-bytes by adding
'. = ALIGN(8);' to the final section before the symbol.
- Ensure that we do have alignment by adding an ASSERT so that when not
aligned we fail to link (and explain why).
- Remove now-spurious '. = ALIGN(x);' statements that were intended to
provide the above alignments.
Tested-by: Michal Simek <michal.simek@amd.com> # Zynq
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
[trini: Also update arch/arm/cpu/armv8/u-boot.lds as Ilas requested]
Signed-off-by: Tom Rini <trini@konsulko.com>
Input from TQ-Systems hardware qualification team.
Fixes performance issues if ethernet and display are used simultaneously.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Max Merchel <Max.Merchel@ew.tq-group.com>
- imply DM_I2C / DM_SPI / DM_MMC / DM_GPIO: boot relevant
- add BUTTON support
- add gpio LED support
- enable CMD_TEMPERATURE to get query temperature in console
- remove Variants that are Kconfig default
- USB ethernet port is not in use by default, remove ethprime
Signed-off-by: Paul Gerber <Paul.Gerber@tq-group.com>
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Max Merchel <Max.Merchel@ew.tq-group.com>
The toradex_smarc_imx95 board exposes three Ethernet ports.
Set the third MAC address equal to the second MAC address.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
SPL will adjust VDD_SOC to OD voltage, because some PMIC uses
0.8V as default for VDD_SOC. So need to call the voltage change
APIs to avoid ELE Glitch Detection triggered reset.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
SPL will adjust VDD_SOC to OD voltage, because some PMIC uses
0.8V as default for VDD_SOC. So need to call the voltage change
APIs to avoid ELE Glitch Detection triggered reset.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The clock settings could be handled by "assigned-clock-rates" through
DM clock driver, so drop setup_fec().
board_init() is a dummy function now, so clean it up.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
With DM_SERIAL and pinctrl driver, the UART pad settings in board code
could be dropped. Then drop board_early_init_f(), since it is a dummy
function now.
While at here, remove WDOG_PAD_CTRL, since no user.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
One of the two on-board PTN5110 TCPC USB Power Delivery controller on
the i.MX93 FRDM board shares its interrupt line whith the PCAL6524 power
controller (GPIO3-27). Since the PTN5110 starts after POR with the
interrupts enabled, this can lead to an interrupt storm on OS startup if
only the driver for the PCAL6524 is loaded, because none is servicing
(and clearing) the interrupt requests from the PTN5110.
Maks and clear all interrupts as part uring board initialization; they
can be re-enabled later by a proper OS driver if required.
Co-developed-by: Joseph Guo <qijian.guo@nxp.com>
Signed-off-by: Francesco Valla <francesco@valla.it>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The eMMC boot device controller on Versal2 requires device pointer
initialization before accessing its sequence number. The EMMC_MODE case
was using dev_seq(dev) on an uninitialized pointer, causing corrupted
boot_targets entries (mmc7f7fbfbf instead of mmc0/mmc1).
Add uclass_get_device_by_name() call to properly initialize the device
pointer before reading the sequence number. The dev sequence number is
determined at runtime based on DT aliases.
Fix boot_targets corruption in eMMC boot mode, allowing proper boot
device selection instead of falling back to JTAG mode.
Signed-off-by: Pranav Tilak <pranav.vinaytilak@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20260113060107.1136297-1-pranav.vinaytilak@amd.com
Make environment support in SPI NOR available in sandbox,
so the environment storage in SPI NOR can be tested in CI.
Enable redundant environment support as well to cover this
in CI tests too.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add new PID4 to ConfigBlock handling:
- 0217 Lino iMX93 Dual 2GB IT
- 0218 Lino iMX91 Solo 2GB IT
- 0219 OSM iMX93 Dual 2GB IT
- 0220 OSM iMX91 Solo 2GB IT
- 0221 Verdin AM62 Dual 1GB ET
Lino and OSM are two new SoM families.
The Verdin variant differs from the existing 0073 Verdin AM62 Dual 1GB ET
by the presence of the GPU (AM625 instead of AM623), the absence of
DSI interface (bridge not mounted) and eMMC size increased to 16GB instead
of 4GB.
Link: https://www.toradex.com/computer-on-modules/lino-arm-family
Link: https://www.toradex.com/computer-on-modules/osm-arm-family
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Our last sync with the kernel was 5.1.
We are so out of sync now, that tracking the patches and backporting
them one by one makes little sense and it's going to take ages.
This is an attempt to sync up Makefiles to 6.1.
Unfortunately due to sheer amount of patches this is not easy to review,
but that's what we decided during a community call for the bump to 5.1,
so we are following the same guidelines here.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>a #rebased on -next
Change mt8365_evk_defconfig to use CONFIG_OF_UPSTREAM=y and delete the
U-Boot copy of the devicetree source files for mt8365.
The upstream devicetree is identical to the U-Boot one being removed
(other than having more nodes for devices not used by U-Boot and
upstream fixed a compatible string in &scpsys, also not affecting
U-Boot).
There was one minor glitch with upstream missing a few topckgen macro
definitions, so those are added to the clock driver directly as a
workaround.
Reviewed-by: Macpaul Lin <macpaul.lin@mediatek.com>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Add board-specific environment variables to imx8ulp_evk.env for better
maintainability. Define bsp_bootcmd in the environment to resolve the
runtime error: "bsp_bootcmd" not defined.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
AMD/Xilinx/FPGA changes for v2026.04-rc1
xilinx:
- Sync ESRT with detected GUID
- DT cleanups
- Add logic for FRU information multiple times
- Enable more drivers pca9541, usb5744
- Enable more commands
- Cleanup firmware DT bindings
firmware:
- Add enhancement SMC format support
clk/versal:
- Various cleanups
- Add support for Versal Gen 2
i2c:
- cdns: Add timeout for RXDV status bit polling
spi:
- cadence: Remove cdns,is-dma DT property
- cadence: Remove duplicated return
- cadence_versal: Update flash reset delay
memtop:
- Update max memory reserved spaces to 64
Versal Gen 2:
- Aligned addresses with default memory map
- Add support for reading multiboot value
MB-V:
- Make SPL smaller
- Add support for SPI
- Move SPL to run out of BRAM
ZynqMP:
- Change default load address for BL32
This pull request brings together a set of fixes and enhancements across
the SoCFPGA platform family, with a focus on MMC/SPL robustness, EFI
boot enablement, and Agilex5 SD/eMMC support.
CI: https://source.denx.de/u-boot/custodians/u-boot-socfpga/-/pipelines/28776
Highlights:
*
SPL / MMC:
o
Fix Kconfig handling for
SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION_TYPE
o
Correct raw sector calculations and respect explicit sector values
when loading U-Boot from MMC in SPL
o
Adjust raw MMC loading logic for SoCFPGA platforms
*
EFI boot:
o
Permit EFI booting on SoCFPGA platforms
o
Disable mkeficapsule tool build for Arria 10 where unsupported
*
Agilex5:
o
Upgrade SDHCI controller from SD4HC to SD6HC
o
Enable MMC and Cadence SDHCI support in defconfig
o
Add dedicated eMMC device tree and defconfig for Agilex5 SoCDK
o
Revert incorrect GPIO configuration for SDIO_SEL
o
Refine U-Boot DT handling for SD and eMMC boot variants
*
SPI:
o
Allow disabling the DesignWare SPI driver in SPL via Kconfig
*
Board / configuration fixes:
o
Enable random MAC address generation for Cyclone V
o
Fix DE0-Nano-SoC boot configuration
o
Remove obsolete or conflicting options from multiple legacy
SoCFPGA defconfigs
We are trying to get rid of the legacy LED API and this is one of the
last users.
As far as I understood from the code, only one LED is controllable and
it is a GPIO led. When initializing the LED, it is always enabled
regardless of the passed argument, same for the mask.
In addition, the LED is used as a BOOT LED.
To keep the same behavior, a GPIO driver should be written, then add a
gpio-leds node which makes use of a GPIO from said driver, add the
/options/u-boot/boot-led property pointing at this new GPIO LED node and
then enable CONFIG_LED as well as CONFIG_LED_BOOT. This should result in
the same behavior using the modern framework.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
