The J784S4 and AM69 Platforms page only details the defconfigs for
J784S4.
Mention the ones needed for AM69-SK as well, to guide users on how to
build for that board.
Signed-off-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Now that USB is enabled on the E850-96 board, DFU and fastboot tools are
functional and can be used to flash images to eMMC. Update the E850-96
documentation accordingly and describe flashing to User Data Area and
Boot HW Partition of eMMC using fastboot and DFU tools.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Introducing documentation support for Qualcomm Dragonwing IQ8 QCS8300
board. Documents the build and flashing steps.
Signed-off-by: Balaji Selvanathan <balaji.selvanathan@oss.qualcomm.com>
i.MX95 B0 uses image container format v2 and needs DUMMY_DDR so that
update imximage.cfg and container.cfg for it.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
This will allow arch(s) that use device tree blobs to pad the end of the
device tree so they can be modified by board files at run time. This will
help prevent errors such as FDT_ERR_NOSPACE from occurring.
Signed-off-by: Eric Schikschneit <eric.schikschneit@novatechautomation.com>
[trini: Change default order so that X86 && EFI_APP works correctly]
Add Retronix R-Car V4H Sparrow Hawk board based on Renesas R-Car V4H ES3.0
(R8A779G3) SoC. This is a single-board computer with single gigabit ethernet,
DSI-to-eDP bridge, DSI and two CSI2 interfaces, audio codec, two CANFD ports,
micro SD card slot, USB PD supply, USB 3.0 ports, M.2 Key-M slot for NVMe SSD,
debug UART and JTAG.
DT is imported from Linux next commit:
a719915e76f2 ("arm64: dts: renesas: r8a779g3: Add Retronix R-Car V4H Sparrow Hawk board support")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Proper U-Boot for Lichee Pi 4A now runs in S mode instead of M mode,
which means the extra firmware, OpenSBI, must be built and integrated
in the image, and the vendor U-Boot cannot chainload the result image
anymore as it runs in M mode.
Remove redundant information about chainloading and update build steps
to mention OpenSBI firmware.
Signed-off-by: Yao Zi <ziyao@disroot.org>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The details of the sysfw.itb from the R5 build that
also needs to be copied as part of the target images
is missing, but is included in the image formats a
little further down, so add it to the instructions.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Support for eMMC, SD card, GPIO and SPL have been available in LPi4A
port. Update the documentation of support status and build
instructions.
Signed-off-by: Yao Zi <ziyao@disroot.org>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The LG Optimus 2X is a touchscreen-based, slate-sized smartphone designed
and manufactured by LG that runs the Android operating system. The
Optimus 2X features a 4" WVGA display, an Nvidia Tegra 2 dual-core chip,
512 MB of RAM and extendable 8 GB of internal storage. UART-B is default
debug port.
Tested-by: Ion Agorria <ion@agorria.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
The LCKFB TaishanPi is a single-board computer based on the RK3566 SoC.
Specification:
- 1/2 Gib RAM
- Optinal EMMC
- SD-Card
- HDMI / MIPI CSI / MIPI DSI
- USB 2.0 Host (Type-A)
- USB 2.0 Host / OTG (Type-C)
- No Ethernet
This patch adds U-Boot support for the LCKFB TaishanPi RK3566 board, including:
- U-Boot device tree
- Default defconfig
- Board documentation
- MAINTAINERS entry
Changes in v2:
- Removed unused configs from `lckfb-tspi-rk3566_defconfig`
- Reordered TaishanPi entry in `doc/board/rockchip/rockchip.rst` alphabetically
Link to v1:
https://lore.kernel.org/u-boot/tencent_95ED0C0545D87B6A8C4B62EC045D53AD2406@qq.com/
Signed-off-by: Jiehui He <jiehui.he@foxmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The 5 Max is another board in the Orange Pi 5 family.
It's overall similar to the 5 Plus, but in a smaller form factor,
which leads to some I/O being reshuffled, but nothing relevant
to u-boot.
So, just reuse the config for the 5 Plus and adjust the DT names.
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Ilya Katsnelson <me@0upti.me>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This patch adds i.MX95 19x19 EVK board basic support.
Messaging unit for EdgeLock Secure Enclave, messaging unit for System
Manager, uSDHC for SD Card, gpio, lpuart are supported now.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The code-block directive requires addition of the prompt symbol for each
line, using the prompt directive instead allows for auto insertion of
the symbol per line[1].
For the readers, the character added by the prompt directive is
un-selectable i.e the entire line can be more easily selected for copy
pasting etc. Whereas with code-block, the prompt symbol like "$" is also
selectable which is usually not the intent.
This is mostly a QoL addition + making the docs consistent since k3.rst
makes use of prompt directives which these board docs include from.
[1]: https://pypi.org/project/sphinx-prompt/
Signed-off-by: Anshul Dalal <anshuld@ti.com>
To avoid duplicate maintenance just include jh7110_common.rst to describe
the usage of the different boot sources.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: E Shattow <e@freeshell.de>
Describe building U-Boot for the board and booting.
Carve out common information for JH7110 boards into an include.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: E Shattow <e@freeshell.de>
Add a minimal generic RK3399 board that only have eMMC, SDMMC, SPI flash
and USB OTG enabled. This defconfig can be used to boot from eMMC,
SD-card or SPI flash on most RK3399 boards that follow reference board
design.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Christopher Obbard <christopher.obbard@linaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a minimal generic RK3328 board that only have eMMC, SDMMC, SPI flash
and USB OTG enabled. This defconfig can be used to boot from eMMC,
SD-card or SPI flash on most RK3328 boards that follow reference board
design.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Christopher Obbard <christopher.obbard@linaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The ROC-RK3576-PC is a SBC made by Firefly, designed around the RK3576
SoC. This adds the needed board infrastructure and config for it.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Rockchip RK3576 is a ARM-based SoC with quad-core Cortex-A72
and quad-core Cortex-A53 including 6TOPS NPU, Mali-G52 MC3, HDMI Out,
DP, eDP, MIPI DSI, MIPI CSI2, LPDDR4/4X/5, eMMC5.1, SD3.0/MMC4.5, UFS,
USB OTG 3.0, Type-C, USB 2.0, PCIe 2.1, SATA 3, Ethernet, SDIO3.0, I2C,
UART, SPI, GPIO and PWM.
Add arch core support for it.
Signed-off-by: Xuhui Lin <xuhui.lin@rock-chips.com>
[adapted for mainline u-boot]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Radxa E20C is an ultra-compact network computer with a RK3528A SoC
that offers a wide range of networking capabilities.
Features tested on a Radxa E20C v1.104:
- SD-card boot
- eMMC boot
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a minimal generic RK3528 board that only have eMMC and SD-card
enabled. This defconfig can be used to boot from eMMC or SD-card on most
RK3528 boards that follow reference board design.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
J722S has hw rng, which can be used by OPTEE.
So remove option to use SW TRNG by OPTEE.
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
The Tegra Note 7 is a mini tablet computer and the second Tegra 4
based mobile device designed by Nvidia that runs the Android operating
system. The Tegra Note has a 7" IPS display with 1280 x 800 (217 ppi)
resolution. The 1 GB of RAM and 16 GB of internal memory can be
supplemented with a microSDXC card giving up to 64 GB of additional
storage.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
The ASUS Transformer Pad TF701T is an Android tablet computer made by
ASUS, successor to the ASUS Transformer Pad Infinity. The tablet includes
a Tegra 4 T114 processor clocked at 1.9 GHz, and an upgraded 2560×1600
pixel resolution screen, increasing the pixel density to 300 PPI and
a mobile dock. Transformers (t114) board derives from Nvidia Macallan
development board.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
The Motorola Atrix 4G (MB860) and Droid X2 (MB870) both featured a
dual-core NVIDIA Tegra 2 AP20H processor clocked at 1GHz, coupled with 1GB
of DDR2 RAM. Storage consisted of 16GB of internal flash memory, expandable
via microSD. The display was a 4.0-inch TFT LCD with a resolution of
960x540 pixels (qHD). The devices originally ran on Android up to 2.3
(Gingerbread).
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Qualcomm changes for v2025.07:
CI: https://source.denx.de/u-boot/custodians/u-boot-snapdragon/-/pipelines/25653
There's been a surprising amount of activity lately on the Qualcomm
side with the two oldest boards getting some fresh attention and a lot
of cleanup and polish going on across the board.
* SDM660 gets USB phy fixes and a pinctrl driver
* The recently added SA8775P/QCS9100 SoC gets a pinctrl driver
* The Qualcomm pinctrl driver now handles reserved pins correctly,
fixing crashes on some boards when running "gpio status -a"
* OF_UPSTREAM_BUILD_VENDOR is enabled in qcom_defconfig
* SDM845 and SC7280 get missing clocks added (since we're now stricter
about those). This gets USB working more reliably in more cases.
* DM_USB_GADGET is enabled for all boards using DWC3 and fasbtoot is
enabled too
* A bug in the livetree fixup code is fixed (making USB work on a lot
more platforms)
* Button label lookup is made case insensitive* bootretry becomes more dynamic, allowing it to be hijacked to make a
"persistent" boot menu that allows dropping to U-Boot shell later on
* A new qcom-phone.config fragment is added along with a phone-specific
default environment and phone-specific debugging/bringup docs. These
make U-Boot more usable on devices without a serial port or keyboard.
* The db820c gets fixed up and updated documentation
* The db410c also gets some love and modernisation as well as a new
reviewer.
* A new driver is added for the USB VBUS regulator found on various
Qualcomm PMICs
* The Qualcomm SPMI driver gets some fixes and cleanup for SPMI v5 and
v7 support.
