* Patch by Marc Singer, 29 May 2003:

Fixed rarp boot method for IA32 and other little-endian CPUs.

* Patch by Marc Singer, 28 May 2003:
  Added port I/O commands.

* Patch by Matthew McClintock, 28 May 2003
  - cpu/mpc824x/start.S: fix relocation code when booting from RAM
  - minor patches for utx8245

* Patch by Daniel Engstr�m, 28 May 2003:
  x86 update

* Patch by Dave Ellis, 9 May 2003 + 27 May 2003:
  add nand flash support to SXNI855T configuration
  fix/extend nand flash support:
  - fix 'nand erase' command so does not erase bad blocks
  - fix 'nand write' command so does not write to bad blocks
  - fix nand_probe() so handles no flash detected properly
  - add doc/README.nand
  - add .jffs2 and .oob options to nand read/write
  - add 'nand bad' command to list bad blocks
  - add 'clean' option to 'nand erase' to write JFFS2 clean markers
  - make NAND read/write faster

* Patch by Rune Torgersen, 23 May 2003:
  Update for MPC8266ADS board

CHANGELOG

@@ -2,6 +2,72 @@
 Changes since U-Boot 0.3.1:
 ======================================================================
 
+* Patch by Marc Singer, 29 May 2003:
+  Fixed rarp boot method for IA32 and other little-endian CPUs.
+
+* Patch by Marc Singer, 28 May 2003:
+  Added port I/O commands.
+
+* Patch by Matthew McClintock, 28 May 2003
+  - cpu/mpc824x/start.S: fix relocation code when booting from RAM
+  - minor patches for utx8245
+
+* Patch by Daniel Engström, 28 May 2003:
+  x86 update
+
+* Patch by Dave Ellis, 9 May 2003 + 27 May 2003:
+  add nand flash support to SXNI855T configuration
+  fix/extend nand flash support:
+  - fix 'nand erase' command so does not erase bad blocks
+  - fix 'nand write' command so does not write to bad blocks
+  - fix nand_probe() so handles no flash detected properly
+  - add doc/README.nand
+  - add .jffs2 and .oob options to nand read/write
+  - add 'nand bad' command to list bad blocks
+  - add 'clean' option to 'nand erase' to write JFFS2 clean markers
+  - make NAND read/write faster
+
+* Patch by Rune Torgersen, 23 May 2003:
+  Update for MPC8266ADS board
+
+* Get (mostly) rid of CFG_MONITOR_LEN definition; compute real length
+  instead CFG_MONITOR_LEN is now only used to determine  _at_compile_
+  _time_  (!) if the environment is embedded within the U-Boot image,
+  or in a separate flash sector.
+
+* Cleanup CFG_DER #defines in config files (wd maintained only)
+
+* Fix data abort exception handling for arm920t CPU
+
+* Fix alignment problems with flash driver for TRAB board
+
+* Patch by Donald White, 21 May 2003:
+  fix calculation of base address in pci_hose_config_device()
+
+* Fix bug in command line parsing: "cmd1;cmd2" is supposed to always
+  execute "cmd2", even if "cmd1" fails. Note that this is different
+  to "run var1 var2" where the contents of "var2" will NOT be
+  executed when a command in "var1" fails.
+
+* Add zero-copy ramdisk support (requires corresponding kernel support!)
+
+* Patch by Kyle Harris, 20 May 2003:
+  In preparation for an ixp port, rename cpu/xscale and arch-xscale
+  into cpu/pxa and arch-pxa.
+
+* Patch by Stefan Roese, 23 May 2003:
+  - IBM PPC405EP port added.
+  - CONFIG_UART1_CONSOLE added. If defined internal UART1 (and not
+    UART0) is used as default U-Boot console. PPC4xx only!
+  - esd ASH405 board added (PPC405EP based).
+  - BUBINGA405EP board added (PPC405EP based - IBM Eval Board).
+  - esd CPCI405AB board added.
+  - esd PMC405 board added.
+  - Update of some esd boards.
+
+* Patch by Denis Peter, 19 Mai 2003:
+  add support for the MIP405-3 board
+
 * Patch by Dave Ellis, 22 May 2003:
   Fix problem with only partially cleared .bss segment
 

MAINTAINERS

@@ -180,14 +180,19 @@ Stefan Roese <stefan.roese@esd-electronics.com>
 
 	ADCIOP			IOP480 (PPC401)
 	AR405			PPC405GP
+	ASH405			PPC405EP
 	CANBT			PPC405CR
 	CPCI405			PPC405GP
+	CPCI4052		PPC405GP
+	CPCI405AB		PPC405GP
 	CPCI440			PPC440GP
 	CPCIISER4		PPC405GP
 	DASA_SIM		IOP480 (PPC401)
 	DU405			PPC405GP
 	OCRTC			PPC405GP
 	ORSG			PPC405GP
+	PCI405			PPC405GP
+	PMC405			PPC405GP
 
 Peter De Schrijver <p2@mind.be>
 

MAKEALL

@@ -44,12 +44,13 @@ LIST_8xx="	\
 #########################################################################
 
 LIST_4xx="	\
-	ADCIOP		AR405		CANBT		CPCI405		\
-	CPCI4052 	CPCI440         CPCIISER4	CRAYL1  	\
-	DASA_SIM	DU405    	EBONY           ERIC  		\
-	MIP405  	ML2		OCRTC		ORSG		\
-	PCI405          PIP405		W7OLMC		W7OLMG          \
-	WALNUT405							\
+	ADCIOP		AR405		ASH405          BUBINGA405EP    \
+        CANBT		CPCI405		CPCI4052 	CPCI405AB       \
+        CPCI440         CPCIISER4	CRAYL1  	DASA_SIM	\
+        DU405    	EBONY           ERIC  		MIP405  	\
+        ML2		OCRTC		ORSG		PCI405          \
+        PIP405		PMC405          W7OLMC		W7OLMG          \
+        WALNUT405	\
 "
 
 #########################################################################
@@ -113,10 +114,10 @@ LIST_ARM9="at91rm9200dk smdk2400 smdk2410 trab VCMA9"
 ## Xscale Systems
 #########################################################################
 
-LIST_xscale="cradle csb226 innokom lubbock wepep250"
+LIST_pxa="cradle csb226 innokom lubbock wepep250"
 
 
-LIST_arm="${LIST_SA} ${LIST_ARM7} ${LIST_ARM9} ${LIST_xscale}"
+LIST_arm="${LIST_SA} ${LIST_ARM7} ${LIST_ARM9} ${LIST_pxa}"
 
 #########################################################################
 ## MIPS 4Kc Systems
@@ -128,6 +129,15 @@ LIST_mips5kc="purple"
 
 LIST_mips="${LIST_mips4kc} ${LIST_mips5kc}"
 
+#########################################################################
+## i386 Systems
+#########################################################################
+
+LIST_I486="sc520_cdp sc520_spunk sc520_spunk_rel"
+
+LIST_x86="${LIST_I486}"
+
+#-----------------------------------------------------------------------
 
 #----- for now, just run PPC by default -----
 [ $# = 0 ] && set $LIST_ppc
@@ -149,7 +159,7 @@ build_target() {
 for arg in $@
 do
 	case "$arg" in
-	5xx|8xx|824x|8260|4xx|7xx|74xx|SA|ARM7|ARM9|ppc|arm|xscale|mips)
+	5xx|8xx|824x|8260|4xx|7xx|74xx|SA|ARM7|ARM9|ppc|arm|pxa|mips|I486|x86)
 			for target in `eval echo '$LIST_'${arg}`
 			do
 				build_target ${target}

Makefile

@@ -60,7 +60,11 @@ ifeq ($(ARCH),arm)
 CROSS_COMPILE = arm-linux-
 endif
 ifeq ($(ARCH),i386)
-#CROSS_COMPILE = i386-elf-
+ifeq ($(HOSTARCH),i386)
+CROSS_COMPILE =
+else
+CROSS_COMPILE = i386-linux-
+endif
 endif
 ifeq ($(ARCH),mips)
 CROSS_COMPILE = mips_4KC-
@@ -403,11 +407,18 @@ ADCIOP_config:	unconfig
 AR405_config:	unconfig
 	@./mkconfig $(@:_config=) ppc ppc4xx ar405 esd
 
+ASH405_config:	unconfig
+	@./mkconfig $(@:_config=) ppc ppc4xx ash405 esd
+
+BUBINGA405EP_config:unconfig
+	@./mkconfig $(@:_config=) ppc ppc4xx bubinga405ep
+
 CANBT_config:	unconfig
 	@./mkconfig $(@:_config=) ppc ppc4xx canbt esd
 
-CPCI405_config		\
-CPCI4052_config:	unconfig
+CPCI405_config	\
+CPCI4052_config	\
+CPCI405AB_config:	unconfig
 	@./mkconfig $(@:_config=) ppc ppc4xx cpci405 esd
 	@echo "BOARD_REVISION = $(@:_config=)"	>>include/config.mk
 
@@ -448,6 +459,9 @@ PCI405_config:	unconfig
 PIP405_config:unconfig
 	@./mkconfig $(@:_config=) ppc ppc4xx pip405 mpl
 
+PMC405_config:	unconfig
+	@./mkconfig $(@:_config=) ppc ppc4xx pmc405 esd
+
 W7OLMC_config	\
 W7OLMG_config: unconfig
 	@./mkconfig $(@:_config=) ppc ppc4xx w7o
@@ -696,19 +710,19 @@ ep7312_config	:	unconfig
 #########################################################################
 
 cradle_config	:	unconfig
-	@./mkconfig $(@:_config=) arm xscale cradle
+	@./mkconfig $(@:_config=) arm pxa cradle 
 
 csb226_config	:	unconfig
-	@./mkconfig $(@:_config=) arm xscale csb226
+	@./mkconfig $(@:_config=) arm pxa csb226
 
 innokom_config	:	unconfig
-	@./mkconfig $(@:_config=) arm xscale innokom
+	@./mkconfig $(@:_config=) arm pxa innokom
 
 lubbock_config	:	unconfig
-	@./mkconfig $(@:_config=) arm xscale lubbock
+	@./mkconfig $(@:_config=) arm pxa lubbock
 
 wepep250_config	:	unconfig
-	@./mkconfig $(@:_config=) arm xscale wepep250
+	@./mkconfig $(@:_config=) arm pxa wepep250
 
 #========================================================================
 # i386
@@ -719,6 +733,12 @@ wepep250_config	:	unconfig
 sc520_cdp_config	:	unconfig
 	@./mkconfig $(@:_config=) i386 i386 sc520_cdp
 
+sc520_spunk_config	:	unconfig
+	@./mkconfig $(@:_config=) i386 i386 sc520_spunk
+
+sc520_spunk_rel_config	:	unconfig
+	@./mkconfig $(@:_config=) i386 i386 sc520_spunk
+
 #========================================================================
 # MIPS
 #========================================================================
@@ -742,7 +762,8 @@ clean:
 		| xargs rm -f
 	rm -f examples/hello_world examples/timer \
 	      examples/eepro100_eeprom examples/sched \
-	      examples/mem_to_mem_idma2intr
+	      examples/mem_to_mem_idma2intr examples/82559_eeprom
+
 	rm -f tools/img2srec tools/mkimage tools/envcrc tools/gen_eth_addr
 	rm -f tools/easylogo/easylogo tools/bmp_logo
 	rm -f tools/gdb/astest tools/gdb/gdbcont tools/gdb/gdbsend

README

@@ -470,6 +470,13 @@ The following options need to be configured:
 		Set to 0 to disable this feature (this is the default).
 		This will also disable hardware handshake.
 
+- Console UART Number:
+		CONFIG_UART1_CONSOLE
+
+		IBM PPC4xx only.
+		If defined internal UART1 (and not UART0) is used
+		as default U-Boot console.
+
 - Boot Delay:	CONFIG_BOOTDELAY - in seconds
 		Delay before automatically booting the default image;
 		set to -1 to disable autoboot.
@@ -1176,13 +1183,13 @@ The following options need to be configured:
 
 	Note:
 
-		In the current implementation, the local variables
-		space and global environment variables space are
-		separated. Local variables are those you define by
-		simply typing like `name=value'. To access a local
-		variable later on, you have write `$name' or
-		`${name}'; variable directly by typing say `$name' at
-		the command prompt.
+                In the current implementation, the local variables
+                space and global environment variables space are
+                separated. Local variables are those you define by
+                simply typing `name=value'. To access a local
+                variable later on, you have write `$name' or
+                `${name}'; to execute the contents of a variable
+                directly type `$name' at the command prompt.
 
 		Global environment variables are those you use
 		setenv/printenv to work with. To run a command stored
@@ -1382,7 +1389,10 @@ Configuration Settings:
 		CFG_FLASH_BASE when booting from flash.
 
 - CFG_MONITOR_LEN:
-		Size of memory reserved for monitor code
+                Size of memory reserved for monitor code, used to
+                determine _at_compile_time_ (!) if the environment is
+                embedded within the U-Boot image, or in a separate
+                flash sector.
 
 - CFG_MALLOC_LEN:
 		Size of DRAM reserved for malloc() use.
@@ -1710,13 +1720,13 @@ Low Level (hardware related) configuration options:
 		#define'd default value in commproc.h resp.
 		cpm_8260.h.
 
-- CFG_PCI_SLV_MEM_LOCAL, CFG_PCI_SLV_MEM_BUS, CFG_PICMR0_MASK_ATTRIB, 
-  CFG_PCI_MSTR0_LOCAL, CFG_PCIMSK0_MASK, CFG_PCI_MSTR1_LOCAL, 
-  CFG_PCIMSK1_MASK, CFG_PCI_MSTR_MEM_LOCAL, CFG_PCI_MSTR_MEM_BUS, 
-  CFG_CPU_PCI_MEM_START, CFG_PCI_MSTR_MEM_SIZE, CFG_POCMR0_MASK_ATTRIB, 
-  CFG_PCI_MSTR_MEMIO_LOCAL, CFG_PCI_MSTR_MEMIO_BUS, CPU_PCI_MEMIO_START, 
-  CFG_PCI_MSTR_MEMIO_SIZE, CFG_POCMR1_MASK_ATTRIB, CFG_PCI_MSTR_IO_LOCAL, 
-  CFG_PCI_MSTR_IO_BUS, CFG_CPU_PCI_IO_START, CFG_PCI_MSTR_IO_SIZE, 
+- CFG_PCI_SLV_MEM_LOCAL, CFG_PCI_SLV_MEM_BUS, CFG_PICMR0_MASK_ATTRIB,
+  CFG_PCI_MSTR0_LOCAL, CFG_PCIMSK0_MASK, CFG_PCI_MSTR1_LOCAL,
+  CFG_PCIMSK1_MASK, CFG_PCI_MSTR_MEM_LOCAL, CFG_PCI_MSTR_MEM_BUS,
+  CFG_CPU_PCI_MEM_START, CFG_PCI_MSTR_MEM_SIZE, CFG_POCMR0_MASK_ATTRIB,
+  CFG_PCI_MSTR_MEMIO_LOCAL, CFG_PCI_MSTR_MEMIO_BUS, CPU_PCI_MEMIO_START,
+  CFG_PCI_MSTR_MEMIO_SIZE, CFG_POCMR1_MASK_ATTRIB, CFG_PCI_MSTR_IO_LOCAL,
+  CFG_PCI_MSTR_IO_BUS, CFG_CPU_PCI_IO_START, CFG_PCI_MSTR_IO_SIZE,
   CFG_POCMR2_MASK_ATTRIB: (MPC826x only)
 		Overrides the default PCI memory map in cpu/mpc8260/pci.c if set.
 
@@ -1981,6 +1991,14 @@ Some configuration options can be set using Environment Variables:
 
 		  setenv initrd_high 00c00000
 
+                  If you set initrd_high to 0xFFFFFFFF, this is an
+                  indication to U-Boot that all addresses are legal
+                  for the Linux kernel, including addresses in flash
+                  memory. In this case U-Boot will NOT COPY the
+                  ramdisk at all. This may be useful to reduce the
+                  boot time on your system, but requires that this
+                  feature is supported by your Linux kernel.
+
   ipaddr	- IP address; needed for tftpboot command
 
   loadaddr	- Default load address for commands like "bootp",
@@ -2033,6 +2051,48 @@ Please note that changes to some configuration parameters may take
 only effect after the next boot (yes, that's just like Windoze :-).
 
 
+Command Line Parsing:
+=====================
+
+There are two different command line parsers available  with  U-Boot:
+the old "simple" one, and the much more pwerful "hush" shell:
+
+Old, simple command line parser:
+--------------------------------
+
+- supports environment variables (through setenv / saveenv commands)
+- several commands on one line, separated by ';'
+- variable substitution using "... $(name) ..." syntax
+- special characters ('$', ';') can be escaped by prefixing with '\',
+  for example:
+	setenv bootcmd bootm \$(address)
+- You can also escape text by enclosing in single apostrophes, for example:
+	setenv addip 'setenv bootargs $bootargs ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off'
+
+Hush shell:
+-----------
+
+- similar to Bourne shell, with control structures like
+  if...then...else...fi, for...do...done; while...do...done,
+  until...do...done, ...
+- supports environment ("global") variables (through setenv / saveenv
+  commands) and local shell variables (through standard shell syntax
+  "name=value"); only environment variables can be used with "run"
+  command
+
+General rules:
+--------------
+
+(1) If a command line (or an environment variable executed by a "run"
+    command) contains several commands separated by semicolon, and
+    one of these commands fails, then the remaining commands will be
+    executed anyway.
+
+(2) If you execute several variables with one call to run (i. e.
+    calling run with a list af variables as arguments), any failing
+    command will cause "run" to terminate, i. e. the remaining
+    variables are not executed.
+
 Note for Redundant Ethernet Interfaces:
 =======================================
 
@@ -2548,9 +2608,9 @@ Minicom warning:
 ================
 
 Over time, many people have reported problems when trying to used the
-"minicom" terminal emulation program  for  serial  download.  I  (wd)
-consider  minicom  to  be  broken, and recommend not to use it. Under
-Unix, I recommend  to  use  CKermit  for  general  purpose  use  (and
+"minicom" terminal emulation program for serial download. I (wd)
+consider minicom to be broken, and recommend not to use it. Under
+Unix, I recommend to use C-Kermit for general purpose use (and
 especially for kermit binary protocol download ("loadb" command), and
 use "cu" for S-Record download ("loads" command).
 

board/LEOX/elpt860/flash.c

@@ -118,7 +118,7 @@ flash_init (void)
   /* monitor protection ON by default */
   flash_protect (FLAG_PROTECT_SET,
 		 CFG_MONITOR_BASE,
-		 CFG_MONITOR_BASE + CFG_MONITOR_LEN-1,
+		 CFG_MONITOR_BASE + monitor_flash_len-1,
 		 &flash_info[0]);
 #endif
   

board/MAI/AmigaOneG3SE/flash_new.c

@@ -120,7 +120,7 @@ unsigned long flash_init (void)
 		/* monitor protection ON by default */
 		flash_protect(FLAG_PROTECT_SET,
 			      CFG_MONITOR_BASE,
-			      CFG_MONITOR_BASE + CFG_MONITOR_LEN - 1,
+			      CFG_MONITOR_BASE + monitor_flash_len - 1,
 			      &flash_info[0]);
 #endif
 

board/MAI/bios_emulator/scitech/src/v86bios/command.c

@@ -36,6 +36,3 @@ getline(char *buf,int *num,int max_num)
     line_pointer = line_pointer + *num;
     len = len - *num;
 }
-
-
-

board/RPXClassic/flash.c

@@ -64,7 +64,7 @@ unsigned long flash_init (void)
 	/* monitor protection ON by default */
 	flash_protect(FLAG_PROTECT_SET,
 		      CFG_MONITOR_BASE,
-		      CFG_MONITOR_BASE+CFG_MONITOR_LEN-1,
+		      CFG_MONITOR_BASE+monitor_flash_len-1,
 		      &flash_info[0]);
 #endif
 

board/RPXlite/flash.c

@@ -85,7 +85,7 @@ unsigned long flash_init (void)
 	/* monitor protection ON by default */
 	flash_protect(FLAG_PROTECT_SET,
 		      CFG_MONITOR_BASE,
-		      CFG_MONITOR_BASE+CFG_MONITOR_LEN-1,
+		      CFG_MONITOR_BASE+monitor_flash_len-1,
 		      &flash_info[0]);
 #endif
 

board/RRvision/flash.c

@@ -73,7 +73,7 @@ unsigned long flash_init (void)
 	/* monitor protection ON by default */
 	flash_protect(FLAG_PROTECT_SET,
 		      CFG_MONITOR_BASE,
-		      CFG_MONITOR_BASE+CFG_MONITOR_LEN-1,
+		      CFG_MONITOR_BASE+monitor_flash_len-1,
 		      &flash_info[0]);
 #endif
 

board/atc/flash.c

@@ -91,7 +91,7 @@ unsigned long flash_init (void)
 	/* monitor protection ON by default */
 	flash_protect(FLAG_PROTECT_SET,
 		      CFG_MONITOR_BASE,
-		      CFG_MONITOR_BASE+CFG_MONITOR_LEN-1,
+		      CFG_MONITOR_BASE+monitor_flash_len-1,
 		      flash_get_info(CFG_MONITOR_BASE));
 #endif
 

board/bmw/flash.c

@@ -219,7 +219,7 @@ flash_init(void)
 #if CFG_MONITOR_BASE >= CFG_FLASH_BASE
     flash_protect(FLAG_PROTECT_SET,
 		CFG_MONITOR_BASE,
-		CFG_MONITOR_BASE + CFG_MONITOR_LEN - 1,
+		CFG_MONITOR_BASE + monitor_flash_len - 1,
 		&flash_info[0]);
 #endif
 

board/bubinga405ep/Makefile

@@ -0,0 +1,47 @@
+#
+# (C) Copyright 2000
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	= $(BOARD).o flash.o
+SOBJS	= init.o
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) crv $@ $^
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+sinclude .depend
+
+#########################################################################

board/bubinga405ep/bubinga405ep.c

@@ -0,0 +1,126 @@
+/*
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+long int spd_sdram (void);
+
+#include <common.h>
+#include "bubinga405ep.h"
+#include <asm/processor.h>
+
+
+int board_pre_init (void)
+{
+	mtdcr (uicsr, 0xFFFFFFFF);      /* clear all ints */
+	mtdcr (uicer, 0x00000000);      /* disable all ints */
+	mtdcr (uiccr, 0x00000010);
+	mtdcr (uicpr, 0xFFFF7FF0);      /* set int polarities */
+	mtdcr (uictr, 0x00000010);      /* set int trigger levels */
+	mtdcr (uicsr, 0xFFFFFFFF);      /* clear all ints */
+
+#if 0
+#define mtebc(reg, data)  mtdcr(ebccfga,reg);mtdcr(ebccfgd,data)
+    /* CS1 */
+	/* BAS=0xF00,BS=0x0(1MB),BU=0x3(R/W),BW=0x0( 8 bits) */
+	mtebc (pb1ap, 0x02815480);
+	mtebc (pb1cr, 0xF0018000);
+
+	p = (unsigned int*)0xEF600708;
+	t = *p;
+	t = t | 0x00000400;
+	*p = t;
+
+	/* BAS=0xF01,BS=0x0(1MB),BU=0x3(R/W),BW=0x0(8 bits) */
+	mtebc (pb2ap, 0x04815A80);
+	mtebc (pb2cr, 0xF0118000);
+
+	/* BAS=0xF02,BS=0x0(1MB),BU=0x3(R/W),BW=0x0( 8 bits) */
+	mtebc (pb3ap, 0x01815280);
+	mtebc (pb3cr, 0xF0218000);
+
+	/* BAS=0xF03,BS=0x0(1MB),BU=0x3(R/W),BW=0x0(8 bits) */
+	mtebc (pb7ap, 0x01815280);
+	mtebc (pb7cr, 0xF0318000);
+
+
+	/* set UART1 control to select CTS/RTS */
+#define FPGA_BRDC       0xF0300004
+	*(volatile char *) (FPGA_BRDC) |= 0x1;
+
+#endif
+
+	return 0;
+}
+
+
+/* ------------------------------------------------------------------------- */
+
+/*
+ * Check Board Identity:
+ */
+
+int checkboard (void)
+{
+	unsigned char *s = getenv ("serial#");
+	unsigned char *e;
+
+	puts ("Board: ");
+
+	if (!s || strncmp (s, "BUBINGA405EP", 9)) {
+		puts ("### No HW ID - assuming WALNUT405");
+	} else {
+		for (e = s; *e; ++e) {
+			if (*e == ' ')
+				break;
+		}
+		for (; s < e; ++s) {
+			putc (*s);
+		}
+	}
+	putc ('\n');
+
+	return (0);
+}
+
+
+/* -------------------------------------------------------------------------
+  initdram(int board_type) reads EEPROM via I2c. EEPROM contains all of
+  the necessary info for SDRAM controller configuration
+   ------------------------------------------------------------------------- */
+long int initdram (int board_type)
+{
+	long int ret;
+
+	ret = spd_sdram ();
+	return ret;
+}
+
+/* ------------------------------------------------------------------------- */
+
+int testdram (void)
+{
+	/* TODO: XXX XXX XXX */
+	printf ("test: xxx MB - ok\n");
+
+	return (0);
+}
+
+/* ------------------------------------------------------------------------- */

board/bubinga405ep/bubinga405ep.h

@@ -0,0 +1,44 @@
+/*
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/****************************************************************************
+ * FLASH Memory Map as used by TQ Monitor:
+ *
+ *                          Start Address    Length
+ * +-----------------------+ 0x4000_0000     Start of Flash -----------------
+ * | MON8xx code           | 0x4000_0100     Reset Vector
+ * +-----------------------+ 0x400?_????
+ * | (unused)              |
+ * +-----------------------+ 0x4001_FF00
+ * | Ethernet Addresses    |                 0x78
+ * +-----------------------+ 0x4001_FF78
+ * | (Reserved for MON8xx) |                 0x44
+ * +-----------------------+ 0x4001_FFBC
+ * | Lock Address          |                 0x04
+ * +-----------------------+ 0x4001_FFC0                     ^
+ * | Hardware Information  |                 0x40            | MON8xx
+ * +=======================+ 0x4002_0000 (sector border)    -----------------
+ * | Autostart Header      |                                 | Applications
+ * | ...                   |                                 v
+ *
+ *****************************************************************************/

board/bubinga405ep/config.mk

@@ -0,0 +1,29 @@
+#
+# (C) Copyright 2000
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# esd ADCIOP boards
+#
+
+#TEXT_BASE = 0xFFFE0000
+TEXT_BASE = 0xFFF80000

board/bubinga405ep/flash.c

@@ -0,0 +1,737 @@
+/*
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * Modified 4/5/2001
+ * Wait for completion of each sector erase command issued
+ * 4/5/2001
+ * Chris Hallinan - DS4.COM, Inc. - clh@net1plus.com
+ */
+
+#include <common.h>
+#include <ppc4xx.h>
+#include <asm/processor.h>
+
+flash_info_t	flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips	*/
+
+/*-----------------------------------------------------------------------
+ * Functions
+ */
+static ulong flash_get_size (vu_long *addr, flash_info_t *info);
+static int write_word (flash_info_t *info, ulong dest, ulong data);
+static void flash_get_offsets (ulong base, flash_info_t *info);
+
+#ifdef CONFIG_ADCIOP
+#define ADDR0           0x0aa9
+#define ADDR1           0x0556
+#define FLASH_WORD_SIZE unsigned char
+#endif
+
+#ifdef CONFIG_CPCI405
+#define ADDR0           0x5555
+#define ADDR1           0x2aaa
+#define FLASH_WORD_SIZE unsigned short
+#endif
+
+#ifdef CONFIG_WALNUT405
+#define ADDR0           0x5555
+#define ADDR1           0x2aaa
+#define FLASH_WORD_SIZE unsigned char
+#endif
+
+#ifdef CONFIG_BUBINGA405EP
+#define ADDR0           0x5555
+#define ADDR1           0x2aaa
+#define FLASH_WORD_SIZE unsigned char
+#endif
+
+
+/*-----------------------------------------------------------------------
+ */
+
+unsigned long flash_init (void)
+{
+	unsigned long size_b0, size_b1;
+	int i;
+        uint pbcr;
+        unsigned long base_b0, base_b1;
+
+	/* Init: no FLASHes known */
+	for (i=0; i<CFG_MAX_FLASH_BANKS; ++i) {
+		flash_info[i].flash_id = FLASH_UNKNOWN;
+	}
+
+	/* Static FLASH Bank configuration here - FIXME XXX */
+
+	size_b0 = flash_get_size((vu_long *)FLASH_BASE0_PRELIM, &flash_info[0]);
+
+	if (flash_info[0].flash_id == FLASH_UNKNOWN) {
+		printf ("## Unknown FLASH on Bank 0 - Size = 0x%08lx = %ld MB\n",
+			size_b0, size_b0<<20);
+	}
+
+	/* Only one bank */
+	if (CFG_MAX_FLASH_BANKS == 1)
+	  {
+	    /* Setup offsets */
+	    flash_get_offsets (FLASH_BASE0_PRELIM, &flash_info[0]);
+
+	    /* Monitor protection ON by default */
+	    (void)flash_protect(FLAG_PROTECT_SET,
+				FLASH_BASE0_PRELIM,
+				FLASH_BASE0_PRELIM+CFG_MONITOR_LEN-1,
+				&flash_info[0]);
+	    size_b1 = 0 ;
+	    flash_info[0].size = size_b0;
+	  }
+
+	/* 2 banks */
+	else
+	  {
+	    size_b1 = flash_get_size((vu_long *)FLASH_BASE1_PRELIM, &flash_info[1]);
+
+	    /* Re-do sizing to get full correct info */
+
+	    if (size_b1)
+	      {
+		mtdcr(ebccfga, pb0cr);
+		pbcr = mfdcr(ebccfgd);
+		mtdcr(ebccfga, pb0cr);
+		base_b1 = -size_b1;
+		pbcr = (pbcr & 0x0001ffff) | base_b1 | (((size_b1/1024/1024)-1)<<17);
+		mtdcr(ebccfgd, pbcr);
+		/*          printf("pb1cr = %x\n", pbcr); */
+	      }
+
+	    if (size_b0)
+	      {
+		mtdcr(ebccfga, pb1cr);
+		pbcr = mfdcr(ebccfgd);
+		mtdcr(ebccfga, pb1cr);
+		base_b0 = base_b1 - size_b0;
+		pbcr = (pbcr & 0x0001ffff) | base_b0 | (((size_b0/1024/1024)-1)<<17);
+		mtdcr(ebccfgd, pbcr);
+		/*            printf("pb0cr = %x\n", pbcr); */
+	      }
+
+	    size_b0 = flash_get_size((vu_long *)base_b0, &flash_info[0]);
+
+	    flash_get_offsets (base_b0, &flash_info[0]);
+
+	    /* monitor protection ON by default */
+	    (void)flash_protect(FLAG_PROTECT_SET,
+				base_b0+size_b0-CFG_MONITOR_LEN,
+				base_b0+size_b0-1,
+				&flash_info[0]);
+
+	    if (size_b1) {
+	      /* Re-do sizing to get full correct info */
+	      size_b1 = flash_get_size((vu_long *)base_b1, &flash_info[1]);
+
+	      flash_get_offsets (base_b1, &flash_info[1]);
+
+	      /* monitor protection ON by default */
+	      (void)flash_protect(FLAG_PROTECT_SET,
+				  base_b1+size_b1-CFG_MONITOR_LEN,
+				  base_b1+size_b1-1,
+				  &flash_info[1]);
+	      /* monitor protection OFF by default (one is enough) */
+	      (void)flash_protect(FLAG_PROTECT_CLEAR,
+				  base_b0+size_b0-CFG_MONITOR_LEN,
+				  base_b0+size_b0-1,
+				  &flash_info[0]);
+	    } else {
+	      flash_info[1].flash_id = FLASH_UNKNOWN;
+	      flash_info[1].sector_count = -1;
+	    }
+
+	    flash_info[0].size = size_b0;
+	    flash_info[1].size = size_b1;
+	  }/* else 2 banks */
+	return (size_b0 + size_b1);
+}
+
+
+
+/*-----------------------------------------------------------------------
+ */
+static void flash_get_offsets (ulong base, flash_info_t *info)
+{
+	int i;
+
+	/* set up sector start address table */
+        if (((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_SST) ||
+	    (info->flash_id  == FLASH_AM040)){
+	    for (i = 0; i < info->sector_count; i++)
+		info->start[i] = base + (i * 0x00010000);
+        } else {
+	    if (info->flash_id & FLASH_BTYPE) {
+		/* set sector offsets for bottom boot block type	*/
+		info->start[0] = base + 0x00000000;
+		info->start[1] = base + 0x00004000;
+		info->start[2] = base + 0x00006000;
+		info->start[3] = base + 0x00008000;
+		for (i = 4; i < info->sector_count; i++) {
+			info->start[i] = base + (i * 0x00010000) - 0x00030000;
+		}
+	    } else {
+		/* set sector offsets for top boot block type		*/
+		i = info->sector_count - 1;
+		info->start[i--] = base + info->size - 0x00004000;
+		info->start[i--] = base + info->size - 0x00006000;
+		info->start[i--] = base + info->size - 0x00008000;
+		for (; i >= 0; i--) {
+			info->start[i] = base + i * 0x00010000;
+		}
+	    }
+	}
+}
+
+/*-----------------------------------------------------------------------
+ */
+void flash_print_info  (flash_info_t *info)
+{
+	int i;
+        int k;
+        int size;
+        int erased;
+        volatile unsigned long *flash;
+
+	if (info->flash_id == FLASH_UNKNOWN) {
+		printf ("missing or unknown FLASH type\n");
+		return;
+	}
+
+	switch (info->flash_id & FLASH_VENDMASK) {
+	case FLASH_MAN_AMD:	printf ("AMD ");		break;
+	case FLASH_MAN_FUJ:	printf ("FUJITSU ");		break;
+	case FLASH_MAN_SST:	printf ("SST ");		break;
+	default:		printf ("Unknown Vendor ");	break;
+	}
+
+	switch (info->flash_id & FLASH_TYPEMASK) {
+	case FLASH_AM040:	printf ("AM29F040 (512 Kbit, uniform sector size)\n");
+				break;
+	case FLASH_AM400B:	printf ("AM29LV400B (4 Mbit, bottom boot sect)\n");
+				break;
+	case FLASH_AM400T:	printf ("AM29LV400T (4 Mbit, top boot sector)\n");
+				break;
+	case FLASH_AM800B:	printf ("AM29LV800B (8 Mbit, bottom boot sect)\n");
+				break;
+	case FLASH_AM800T:	printf ("AM29LV800T (8 Mbit, top boot sector)\n");
+				break;
+	case FLASH_AM160B:	printf ("AM29LV160B (16 Mbit, bottom boot sect)\n");
+				break;
+	case FLASH_AM160T:	printf ("AM29LV160T (16 Mbit, top boot sector)\n");
+				break;
+	case FLASH_AM320B:	printf ("AM29LV320B (32 Mbit, bottom boot sect)\n");
+				break;
+	case FLASH_AM320T:	printf ("AM29LV320T (32 Mbit, top boot sector)\n");
+				break;
+	case FLASH_SST800A:	printf ("SST39LF/VF800 (8 Mbit, uniform sector size)\n");
+				break;
+	case FLASH_SST160A:	printf ("SST39LF/VF160 (16 Mbit, uniform sector size)\n");
+				break;
+	default:		printf ("Unknown Chip Type\n");
+				break;
+	}
+
+	printf ("  Size: %ld KB in %d Sectors\n",
+		info->size >> 10, info->sector_count);
+
+	printf ("  Sector Start Addresses:");
+	for (i=0; i<info->sector_count; ++i) {
+                /*
+                 * Check if whole sector is erased
+                 */
+                if (i != (info->sector_count-1))
+                  size = info->start[i+1] - info->start[i];
+                else
+                  size = info->start[0] + info->size - info->start[i];
+                erased = 1;
+                flash = (volatile unsigned long *)info->start[i];
+                size = size >> 2;        /* divide by 4 for longword access */
+                for (k=0; k<size; k++)
+                  {
+                    if (*flash++ != 0xffffffff)
+                      {
+                        erased = 0;
+                        break;
+                      }
+                  }
+
+		if ((i % 5) == 0)
+			printf ("\n   ");
+#if 0 /* test-only */
+		printf (" %08lX%s",
+			info->start[i],
+			info->protect[i] ? " (RO)" : "     "
+#else
+		printf (" %08lX%s%s",
+			info->start[i],
+			erased ? " E" : "  ",
+			info->protect[i] ? "RO " : "   "
+#endif
+		);
+	}
+	printf ("\n");
+	return;
+}
+
+/*-----------------------------------------------------------------------
+ */
+
+
+/*-----------------------------------------------------------------------
+ */
+
+/*
+ * The following code cannot be run from FLASH!
+ */
+static ulong flash_get_size (vu_long *addr, flash_info_t *info)
+{
+	short i;
+	FLASH_WORD_SIZE value;
+	ulong base = (ulong)addr;
+        volatile FLASH_WORD_SIZE *addr2 = (FLASH_WORD_SIZE *)addr;
+
+	/* Write auto select command: read Manufacturer ID */
+	addr2[ADDR0] = (FLASH_WORD_SIZE)0x00AA00AA;
+	addr2[ADDR1] = (FLASH_WORD_SIZE)0x00550055;
+	addr2[ADDR0] = (FLASH_WORD_SIZE)0x00900090;
+
+#ifdef CONFIG_ADCIOP
+	value = addr2[2];
+#else
+	value = addr2[0];
+#endif
+
+	switch (value) {
+	case (FLASH_WORD_SIZE)AMD_MANUFACT:
+		info->flash_id = FLASH_MAN_AMD;
+		break;
+	case (FLASH_WORD_SIZE)FUJ_MANUFACT:
+		info->flash_id = FLASH_MAN_FUJ;
+		break;
+	case (FLASH_WORD_SIZE)SST_MANUFACT:
+		info->flash_id = FLASH_MAN_SST;
+		break;
+	default:
+		info->flash_id = FLASH_UNKNOWN;
+		info->sector_count = 0;
+		info->size = 0;
+		return (0);			/* no or unknown flash	*/
+	}
+
+#ifdef CONFIG_ADCIOP
+	value = addr2[0];			/* device ID		*/
+        /*        printf("\ndev_code=%x\n", value); */
+#else
+	value = addr2[1];			/* device ID		*/
+#endif
+
+	switch (value) {
+	case (FLASH_WORD_SIZE)AMD_ID_F040B:
+	        info->flash_id += FLASH_AM040;
+		info->sector_count = 8;
+		info->size = 0x0080000; /* => 512 ko */
+		break;
+	case (FLASH_WORD_SIZE)AMD_ID_LV400T:
+		info->flash_id += FLASH_AM400T;
+		info->sector_count = 11;
+		info->size = 0x00080000;
+		break;				/* => 0.5 MB		*/
+
+	case (FLASH_WORD_SIZE)AMD_ID_LV400B:
+		info->flash_id += FLASH_AM400B;
+		info->sector_count = 11;
+		info->size = 0x00080000;
+		break;				/* => 0.5 MB		*/
+
+	case (FLASH_WORD_SIZE)AMD_ID_LV800T:
+		info->flash_id += FLASH_AM800T;
+		info->sector_count = 19;
+		info->size = 0x00100000;
+		break;				/* => 1 MB		*/
+
+	case (FLASH_WORD_SIZE)AMD_ID_LV800B:
+		info->flash_id += FLASH_AM800B;
+		info->sector_count = 19;
+		info->size = 0x00100000;
+		break;				/* => 1 MB		*/
+
+	case (FLASH_WORD_SIZE)AMD_ID_LV160T:
+		info->flash_id += FLASH_AM160T;
+		info->sector_count = 35;
+		info->size = 0x00200000;
+		break;				/* => 2 MB		*/
+
+	case (FLASH_WORD_SIZE)AMD_ID_LV160B:
+		info->flash_id += FLASH_AM160B;
+		info->sector_count = 35;
+		info->size = 0x00200000;
+		break;				/* => 2 MB		*/
+#if 0	/* enable when device IDs are available */
+	case (FLASH_WORD_SIZE)AMD_ID_LV320T:
+		info->flash_id += FLASH_AM320T;
+		info->sector_count = 67;
+		info->size = 0x00400000;
+		break;				/* => 4 MB		*/
+
+	case (FLASH_WORD_SIZE)AMD_ID_LV320B:
+		info->flash_id += FLASH_AM320B;
+		info->sector_count = 67;
+		info->size = 0x00400000;
+		break;				/* => 4 MB		*/
+#endif
+	case (FLASH_WORD_SIZE)SST_ID_xF800A:
+		info->flash_id += FLASH_SST800A;
+		info->sector_count = 16;
+		info->size = 0x00100000;
+		break;				/* => 1 MB		*/
+
+	case (FLASH_WORD_SIZE)SST_ID_xF160A:
+		info->flash_id += FLASH_SST160A;
+		info->sector_count = 32;
+		info->size = 0x00200000;
+		break;				/* => 2 MB		*/
+
+	default:
+		info->flash_id = FLASH_UNKNOWN;
+		return (0);			/* => no or unknown flash */
+
+	}
+
+	/* set up sector start address table */
+        if (((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_SST) ||
+	    (info->flash_id  == FLASH_AM040)){
+	    for (i = 0; i < info->sector_count; i++)
+		info->start[i] = base + (i * 0x00010000);
+        } else {
+	    if (info->flash_id & FLASH_BTYPE) {
+		/* set sector offsets for bottom boot block type	*/
+		info->start[0] = base + 0x00000000;
+		info->start[1] = base + 0x00004000;
+		info->start[2] = base + 0x00006000;
+		info->start[3] = base + 0x00008000;
+		for (i = 4; i < info->sector_count; i++) {
+			info->start[i] = base + (i * 0x00010000) - 0x00030000;
+		}
+	    } else {
+		/* set sector offsets for top boot block type		*/
+		i = info->sector_count - 1;
+		info->start[i--] = base + info->size - 0x00004000;
+		info->start[i--] = base + info->size - 0x00006000;
+		info->start[i--] = base + info->size - 0x00008000;
+		for (; i >= 0; i--) {
+			info->start[i] = base + i * 0x00010000;
+		}
+	    }
+	}
+
+	/* check for protected sectors */
+	for (i = 0; i < info->sector_count; i++) {
+		/* read sector protection at sector address, (A7 .. A0) = 0x02 */
+		/* D0 = 1 if protected */
+#ifdef CONFIG_ADCIOP
+		addr2 = (volatile FLASH_WORD_SIZE *)(info->start[i]);
+		info->protect[i] = addr2[4] & 1;
+#else
+		addr2 = (volatile FLASH_WORD_SIZE *)(info->start[i]);
+                if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_SST)
+                  info->protect[i] = 0;
+                else
+                  info->protect[i] = addr2[2] & 1;
+#endif
+	}
+
+	/*
+	 * Prevent writes to uninitialized FLASH.
+	 */
+	if (info->flash_id != FLASH_UNKNOWN) {
+#if 0 /* test-only */
+#ifdef CONFIG_ADCIOP
+		addr2 = (volatile unsigned char *)info->start[0];
+                addr2[ADDR0] = 0xAA;
+                addr2[ADDR1] = 0x55;
+                addr2[ADDR0] = 0xF0;  /* reset bank */
+#else
+		addr2 = (FLASH_WORD_SIZE *)info->start[0];
+		*addr2 = (FLASH_WORD_SIZE)0x00F000F0;	/* reset bank */
+#endif
+#else /* test-only */
+		addr2 = (FLASH_WORD_SIZE *)info->start[0];
+		*addr2 = (FLASH_WORD_SIZE)0x00F000F0;	/* reset bank */
+#endif /* test-only */
+	}
+
+	return (info->size);
+}
+
+int wait_for_DQ7(flash_info_t *info, int sect)
+{
+	ulong start, now, last;
+	volatile FLASH_WORD_SIZE *addr = (FLASH_WORD_SIZE *)(info->start[sect]);
+
+	start = get_timer (0);
+    last  = start;
+    while ((addr[0] & (FLASH_WORD_SIZE)0x00800080) != (FLASH_WORD_SIZE)0x00800080) {
+        if ((now = get_timer(start)) > CFG_FLASH_ERASE_TOUT) {
+            printf ("Timeout\n");
+            return -1;
+        }
+        /* show that we're waiting */
+        if ((now - last) > 1000) {  /* every second */
+            putc ('.');
+            last = now;
+        }
+    }
+	return 0;
+}
+
+/*-----------------------------------------------------------------------
+ */
+
+int	flash_erase (flash_info_t *info, int s_first, int s_last)
+{
+	volatile FLASH_WORD_SIZE *addr = (FLASH_WORD_SIZE *)(info->start[0]);
+	volatile FLASH_WORD_SIZE *addr2;
+	int flag, prot, sect, l_sect;
+	int i;
+
+	if ((s_first < 0) || (s_first > s_last)) {
+		if (info->flash_id == FLASH_UNKNOWN) {
+			printf ("- missing\n");
+		} else {
+			printf ("- no sectors to erase\n");
+		}
+		return 1;
+	}
+
+	if (info->flash_id == FLASH_UNKNOWN) {
+		printf ("Can't erase unknown flash type - aborted\n");
+		return 1;
+	}
+
+	prot = 0;
+	for (sect=s_first; sect<=s_last; ++sect) {
+		if (info->protect[sect]) {
+			prot++;
+		}
+	}
+
+	if (prot) {
+		printf ("- Warning: %d protected sectors will not be erased!\n",
+			prot);
+	} else {
+		printf ("\n");
+	}
+
+	l_sect = -1;
+
+	/* Disable interrupts which might cause a timeout here */
+	flag = disable_interrupts();
+
+	/* Start erase on unprotected sectors */
+	for (sect = s_first; sect<=s_last; sect++) {
+		if (info->protect[sect] == 0) {	/* not protected */
+		    addr2 = (FLASH_WORD_SIZE *)(info->start[sect]);
+		    printf("Erasing sector %p\n", addr2);	/* CLH */
+
+		    if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_SST) {
+			addr[ADDR0] = (FLASH_WORD_SIZE)0x00AA00AA;
+			addr[ADDR1] = (FLASH_WORD_SIZE)0x00550055;
+			addr[ADDR0] = (FLASH_WORD_SIZE)0x00800080;
+			addr[ADDR0] = (FLASH_WORD_SIZE)0x00AA00AA;
+			addr[ADDR1] = (FLASH_WORD_SIZE)0x00550055;
+			addr2[0] = (FLASH_WORD_SIZE)0x00500050;  /* block erase */
+			for (i=0; i<50; i++)
+				udelay(1000);  /* wait 1 ms */
+		    } else {
+			addr[ADDR0] = (FLASH_WORD_SIZE)0x00AA00AA;
+			addr[ADDR1] = (FLASH_WORD_SIZE)0x00550055;
+			addr[ADDR0] = (FLASH_WORD_SIZE)0x00800080;
+			addr[ADDR0] = (FLASH_WORD_SIZE)0x00AA00AA;
+			addr[ADDR1] = (FLASH_WORD_SIZE)0x00550055;
+			addr2[0] = (FLASH_WORD_SIZE)0x00300030;  /* sector erase */
+		    }
+		    l_sect = sect;
+		    /*
+		     * Wait for each sector to complete, it's more
+		     * reliable.  According to AMD Spec, you must
+		     * issue all erase commands within a specified
+		     * timeout.  This has been seen to fail, especially
+		     * if printf()s are included (for debug)!!
+		     */
+		    wait_for_DQ7(info, sect);
+		}
+	}
+
+	/* re-enable interrupts if necessary */
+	if (flag)
+		enable_interrupts();
+
+	/* wait at least 80us - let's wait 1 ms */
+	udelay (1000);
+
+#if 0
+	/*
+	 * We wait for the last triggered sector
+	 */
+	if (l_sect < 0)
+		goto DONE;
+	wait_for_DQ7(info, l_sect);
+
+DONE:
+#endif
+	/* reset to read mode */
+	addr = (FLASH_WORD_SIZE *)info->start[0];
+	addr[0] = (FLASH_WORD_SIZE)0x00F000F0;	/* reset bank */
+
+	printf (" done\n");
+	return 0;
+}
+
+/*-----------------------------------------------------------------------
+ * Copy memory to flash, returns:
+ * 0 - OK
+ * 1 - write timeout
+ * 2 - Flash not erased
+ */
+
+int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
+{
+	ulong cp, wp, data;
+	int i, l, rc;
+
+	wp = (addr & ~3);	/* get lower word aligned address */
+
+	/*
+	 * handle unaligned start bytes
+	 */
+	if ((l = addr - wp) != 0) {
+		data = 0;
+		for (i=0, cp=wp; i<l; ++i, ++cp) {
+			data = (data << 8) | (*(uchar *)cp);
+		}
+		for (; i<4 && cnt>0; ++i) {
+			data = (data << 8) | *src++;
+			--cnt;
+			++cp;
+		}
+		for (; cnt==0 && i<4; ++i, ++cp) {
+			data = (data << 8) | (*(uchar *)cp);
+		}
+
+		if ((rc = write_word(info, wp, data)) != 0) {
+			return (rc);
+		}
+		wp += 4;
+	}
+
+	/*
+	 * handle word aligned part
+	 */
+	while (cnt >= 4) {
+		data = 0;
+		for (i=0; i<4; ++i) {
+			data = (data << 8) | *src++;
+		}
+		if ((rc = write_word(info, wp, data)) != 0) {
+			return (rc);
+		}
+		wp  += 4;
+		cnt -= 4;
+	}
+
+	if (cnt == 0) {
+		return (0);
+	}
+
+	/*
+	 * handle unaligned tail bytes
+	 */
+	data = 0;
+	for (i=0, cp=wp; i<4 && cnt>0; ++i, ++cp) {
+		data = (data << 8) | *src++;
+		--cnt;
+	}
+	for (; i<4; ++i, ++cp) {
+		data = (data << 8) | (*(uchar *)cp);
+	}
+
+	return (write_word(info, wp, data));
+}
+
+/*-----------------------------------------------------------------------
+ * Write a word to Flash, returns:
+ * 0 - OK
+ * 1 - write timeout
+ * 2 - Flash not erased
+ */
+static int write_word (flash_info_t * info, ulong dest, ulong data)
+{
+	volatile FLASH_WORD_SIZE *addr2 = (FLASH_WORD_SIZE *) (info->start[0]);
+	volatile FLASH_WORD_SIZE *dest2 = (FLASH_WORD_SIZE *) dest;
+	volatile FLASH_WORD_SIZE *data2 = (FLASH_WORD_SIZE *) & data;
+	ulong start;
+	int i;
+
+	/* Check if Flash is (sufficiently) erased */
+	if ((*((volatile FLASH_WORD_SIZE *) dest) &
+	    (FLASH_WORD_SIZE) data) != (FLASH_WORD_SIZE) data) {
+		return (2);
+	}
+
+	for (i = 0; i < 4 / sizeof (FLASH_WORD_SIZE); i++) {
+		int flag;
+
+		/* Disable interrupts which might cause a timeout here */
+		flag = disable_interrupts ();
+
+		addr2[ADDR0] = (FLASH_WORD_SIZE) 0x00AA00AA;
+		addr2[ADDR1] = (FLASH_WORD_SIZE) 0x00550055;
+		addr2[ADDR0] = (FLASH_WORD_SIZE) 0x00A000A0;
+
+		dest2[i] = data2[i];
+
+		/* re-enable interrupts if necessary */
+		if (flag)
+			enable_interrupts ();
+
+		/* data polling for D7 */
+		start = get_timer (0);
+		while ((dest2[i] & (FLASH_WORD_SIZE) 0x00800080) !=
+		       (data2[i] & (FLASH_WORD_SIZE) 0x00800080)) {
+
+			if (get_timer (start) > CFG_FLASH_WRITE_TOUT) {
+				return (1);
+			}
+		}
+	}
+
+	return (0);
+}
+
+/*-----------------------------------------------------------------------
+ */

board/bubinga405ep/init.S

@@ -0,0 +1,55 @@
+/*------------------------------------------------------------------------------+ */
+/* */
+/*       This source code has been made available to you by IBM on an AS-IS */
+/*       basis.  Anyone receiving this source is licensed under IBM */
+/*       copyrights to use it in any way he or she deems fit, including */
+/*       copying it, modifying it, compiling it, and redistributing it either */
+/*       with or without modifications.  No license under IBM patents or */
+/*       patent applications is to be implied by the copyright license. */
+/* */
+/*       Any user of this software should understand that IBM cannot provide */
+/*       technical support for this software and will not be responsible for */
+/*       any consequences resulting from the use of this software. */
+/* */
+/*       Any person who transfers this source code or any derivative work */
+/*       must include the IBM copyright notice, this paragraph, and the */
+/*       preceding two paragraphs in the transferred software. */
+/* */
+/*       COPYRIGHT   I B M   CORPORATION 1995 */
+/*       LICENSED MATERIAL  -  PROGRAM PROPERTY OF I B M */
+/*------------------------------------------------------------------------------- */
+
+/*----------------------------------------------------------------------------- */
+/* Function:     ext_bus_cntlr_init */
+/* Description:  Initializes the External Bus Controller for the external */
+/*		peripherals. IMPORTANT: For pass1 this code must run from */
+/*		cache since you can not reliably change a peripheral banks */
+/*		timing register (pbxap) while running code from that bank. */
+/*		For ex., since we are running from ROM on bank 0, we can NOT */
+/*		execute the code that modifies bank 0 timings from ROM, so */
+/*		we run it from cache. */
+/*	Bank 0 - Flash and SRAM */
+/*	Bank 1 - NVRAM/RTC */
+/*	Bank 2 - Keyboard/Mouse controller */
+/*	Bank 3 - IR controller */
+/*	Bank 4 - not used */
+/*	Bank 5 - not used */
+/*	Bank 6 - not used */
+/*	Bank 7 - FPGA registers */
+/*----------------------------------------------------------------------------- */
+#include <ppc4xx.h>
+
+#include <ppc_asm.tmpl>
+#include <ppc_defs.h>
+
+#include <asm/cache.h>
+#include <asm/mmu.h>
+
+
+/*----------------------------------------------------------------------------- */
+/* Function:     sdram_init */
+/* Description:  Dummy implementation here - done in C later */
+/*----------------------------------------------------------------------------- */
+        .globl  sdram_init
+sdram_init:
+        blr

board/bubinga405ep/u-boot.lds

@@ -0,0 +1,144 @@
+/*
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+/* Do we need any of these for elf?
+   __DYNAMIC = 0;    */
+SECTIONS
+{
+  .resetvec 0xFFFFFFFC :
+  {
+    *(.resetvec)
+  } = 0xffff
+
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)		}
+  .rela.text     : { *(.rela.text) 	}
+  .rel.data      : { *(.rel.data)		}
+  .rela.data     : { *(.rela.data) 	}
+  .rel.rodata    : { *(.rel.rodata) 	}
+  .rela.rodata   : { *(.rela.rodata) 	}
+  .rel.got       : { *(.rel.got)		}
+  .rela.got      : { *(.rela.got)		}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)		}
+  .rela.bss      : { *(.rela.bss)		}
+  .rel.plt       : { *(.rel.plt)		}
+  .rela.plt      : { *(.rela.plt)		}
+  .init          : { *(.init)	}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    /* WARNING - the following is hand-optimized to fit within	*/
+    /* the sector layout of our flash chips!	XXX FIXME XXX	*/
+
+    cpu/ppc4xx/start.o	(.text)
+    board/bubinga405ep/init.o	(.text)
+    cpu/ppc4xx/kgdb.o	(.text)
+    cpu/ppc4xx/traps.o	(.text)
+    cpu/ppc4xx/interrupts.o	(.text)
+    cpu/ppc4xx/serial.o	(.text)
+    cpu/ppc4xx/cpu_init.o	(.text)
+    cpu/ppc4xx/speed.o	(.text)
+    cpu/ppc4xx/405gp_enet.o	(.text)
+    common/dlmalloc.o	(.text)
+    lib_generic/crc32.o		(.text)
+    lib_ppc/extable.o	(.text)
+    lib_generic/zlib.o		(.text)
+
+/*    . = env_offset;*/
+/*    common/environment.o(.text)*/
+
+    *(.text)
+    *(.fixup)
+    *(.got1)
+  }
+  _etext = .;
+  PROVIDE (etext = .);
+  .rodata    :
+  {
+    *(.rodata)
+    *(.rodata1)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x00FF) & 0xFFFFFF00;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
+  __fixup_entries = (. - _FIXUP_TABLE_)>>2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(256);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(256);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+  _end = . ;
+  PROVIDE (end = .);
+}

board/bubinga405ep/u-boot.lds.debug

@@ -0,0 +1,147 @@
+/*
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+/* Do we need any of these for elf?
+   __DYNAMIC = 0;    */
+SECTIONS
+{
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)		}
+  .rela.text     : { *(.rela.text) 	}
+  .rel.data      : { *(.rel.data)		}
+  .rela.data     : { *(.rela.data) 	}
+  .rel.rodata    : { *(.rel.rodata) 	}
+  .rela.rodata   : { *(.rela.rodata) 	}
+  .rel.got       : { *(.rel.got)		}
+  .rela.got      : { *(.rela.got)		}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)		}
+  .rela.bss      : { *(.rela.bss)		}
+  .rel.plt       : { *(.rel.plt)		}
+  .rela.plt      : { *(.rela.plt)		}
+  .init          : { *(.init)	}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    /* WARNING - the following is hand-optimized to fit within	*/
+    /* the sector layout of our flash chips!	XXX FIXME XXX	*/
+
+/*
+    cpu/ppc4xx/start.o	(.text)
+    common/dlmalloc.o	(.text)
+    lib_generic/vsprintf.o	(.text)
+    lib_generic/crc32.o		(.text)
+    lib_ppc/extable.o	(.text)
+*/
+    cpu/ppc4xx/start.o	(.text)
+    board/bubinga405ep/init.o	(.text)
+    cpu/ppc4xx/kgdb.o	(.text)
+    cpu/ppc4xx/traps.o	(.text)
+    cpu/ppc4xx/interrupts.o	(.text)
+    cpu/ppc4xx/serial.o	(.text)
+    cpu/ppc4xx/cpu_init.o	(.text)
+    cpu/ppc4xx/speed.o	(.text)
+    cpu/ppc4xx/405gp_enet.o	(.text)
+    common/dlmalloc.o	(.text)
+    lib_generic/crc32.o		(.text)
+    lib_ppc/extable.o	(.text)
+    lib_generic/zlib.o		(.text)
+
+
+    common/environment.o(.text)
+
+    *(.text)
+    *(.fixup)
+    *(.got1)
+  }
+  _etext = .;
+  PROVIDE (etext = .);
+  .rodata    :
+  {
+    *(.rodata)
+    *(.rodata1)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x0FFF) & 0xFFFFF000;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
+  __fixup_entries = (. - _FIXUP_TABLE_)>>2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(4096);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(4096);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+  _end = . ;
+  PROVIDE (end = .);
+}
+

board/c2mon/flash.c

@@ -91,7 +91,7 @@ unsigned long flash_init (void)
 	/* monitor protection ON by default */
 	flash_protect(FLAG_PROTECT_SET,
 		      CFG_MONITOR_BASE,
-		      CFG_MONITOR_BASE+CFG_MONITOR_LEN-1,
+		      CFG_MONITOR_BASE+monitor_flash_len-1,
 		      &flash_info[0]);
 #endif
 
@@ -118,7 +118,7 @@ unsigned long flash_init (void)
 		/* monitor protection ON by default */
 		flash_protect(FLAG_PROTECT_SET,
 			      CFG_MONITOR_BASE,
-			      CFG_MONITOR_BASE+CFG_MONITOR_LEN-1,
+			      CFG_MONITOR_BASE+monitor_flash_len-1,
 			      &flash_info[1]);
 #endif
 

board/cmi/flash.c

@@ -106,7 +106,7 @@ unsigned long flash_init (void)
 	/* monitor protection ON by default */
 	flash_protect(FLAG_PROTECT_SET,
 		      CFG_MONITOR_BASE,
-		      CFG_MONITOR_BASE+CFG_MONITOR_LEN-1,
+		      CFG_MONITOR_BASE+monitor_flash_len-1,
 		      &flash_info[0]);
 #endif
 

board/cogent/flash.c

@@ -323,7 +323,7 @@ flash_init(void)
 #if CFG_MONITOR_BASE == CFG_FLASH_BASE
 	flash_protect(FLAG_PROTECT_SET,
 		      CFG_MONITOR_BASE,
-		      CFG_MONITOR_BASE+CFG_MONITOR_LEN-1,
+		      CFG_MONITOR_BASE+monitor_flash_len-1,
 		      &flash_info[0]);
 #endif
 

board/cpc45/flash.c

@@ -132,12 +132,12 @@ unsigned long flash_init(void)
 #if CFG_MONITOR_BASE >= CFG_FLASH_BASE + FLASH_BANK_SIZE
     flash_protect(FLAG_PROTECT_SET,
               CFG_MONITOR_BASE,
-              CFG_MONITOR_BASE + CFG_MONITOR_LEN - 1,
+              CFG_MONITOR_BASE + monitor_flash_len - 1,
               &flash_info[1]);
 #else
     flash_protect(FLAG_PROTECT_SET,
               CFG_MONITOR_BASE,
-              CFG_MONITOR_BASE + CFG_MONITOR_LEN - 1,
+              CFG_MONITOR_BASE + monitor_flash_len - 1,
               &flash_info[0]);
 #endif
 #endif

board/cpu86/flash.c

@@ -218,14 +218,14 @@ unsigned long flash_init (void)
 
 		flash_protect  (FLAG_PROTECT_SET,
 				CFG_MONITOR_BASE,
-				CFG_MONITOR_BASE + CFG_MONITOR_LEN - 1, &flash_info[1]
+				CFG_MONITOR_BASE + monitor_flash_len - 1, &flash_info[1]
 		);
 	}
 #else
 #if CFG_MONITOR_BASE >= CFG_FLASH_BASE
 	flash_protect (FLAG_PROTECT_SET,
 		       CFG_MONITOR_BASE,
-		       CFG_MONITOR_BASE + CFG_MONITOR_LEN - 1, &flash_info[0]
+		       CFG_MONITOR_BASE + monitor_flash_len - 1, &flash_info[0]
 	);
 #endif
 #endif

board/cradle/flash.c

@@ -73,7 +73,7 @@ ulong flash_init(void)
     */
    flash_protect(FLAG_PROTECT_SET,
                   CFG_FLASH_BASE,
-                  CFG_FLASH_BASE + _armboot_end_data - _armboot_start,
+                  CFG_FLASH_BASE + monitor_flash_len - 1,
                   &flash_info[0]);
 
    flash_protect(FLAG_PROTECT_SET,

board/cradle/u-boot.lds

@@ -31,7 +31,7 @@ SECTIONS
         . = ALIGN(4);
 	.text      :
 	{
-	  cpu/xscale/start.o	(.text)
+	  cpu/pxa/start.o	(.text)
 	  *(.text)
 	}
 

board/cray/L1/flash.c

@@ -88,7 +88,7 @@ unsigned long flash_init (void)
 	    /* Monitor protection ON by default */
 	    (void)flash_protect(FLAG_PROTECT_SET,
 				FLASH_BASE0_PRELIM,
-				FLASH_BASE0_PRELIM+CFG_MONITOR_LEN-1,
+				FLASH_BASE0_PRELIM+monitor_flash_len-1,
 				&flash_info[0]);
 #endif
 	    size_b1 = 0 ;

board/csb226/flash.c

@@ -74,7 +74,7 @@ ulong flash_init(void)
 	/* Protect monitor and environment sectors */
 	flash_protect(FLAG_PROTECT_SET,
 			CFG_FLASH_BASE,
-			CFG_FLASH_BASE + _armboot_end_data - _armboot_start,
+			CFG_FLASH_BASE + monitor_flash_len - 1,
 			&flash_info[0]);
 
 	flash_protect(FLAG_PROTECT_SET,

board/csb226/u-boot.lds

@@ -31,7 +31,7 @@ SECTIONS
         . = ALIGN(4);
 	.text      :
 	{
-	  cpu/xscale/start.o	(.text)
+	  cpu/pxa/start.o	(.text)
 	  *(.text)
 	}
 

board/cu824/flash.c

@@ -125,12 +125,12 @@ unsigned long flash_init(void)
 #if CFG_MONITOR_BASE >= CFG_FLASH_BASE + FLASH_BANK_SIZE
     flash_protect(FLAG_PROTECT_SET,
               CFG_MONITOR_BASE,
-              CFG_MONITOR_BASE + CFG_MONITOR_LEN - 1,
+              CFG_MONITOR_BASE + monitor_flash_len - 1,
               &flash_info[1]);
 #else
     flash_protect(FLAG_PROTECT_SET,
               CFG_MONITOR_BASE,
-              CFG_MONITOR_BASE + CFG_MONITOR_LEN - 1,
+              CFG_MONITOR_BASE + monitor_flash_len - 1,
               &flash_info[0]);
 #endif
 #endif

board/dnp1110/flash.c

@@ -84,7 +84,7 @@ unsigned long flash_init (void)
      */
     flash_protect(FLAG_PROTECT_SET,
 		  CFG_FLASH_BASE,
-		  CFG_FLASH_BASE + _armboot_end_data - _armboot_start,
+		  CFG_FLASH_BASE + monitor_flash_len  - 1,
 		  &flash_info[0]);
 
     flash_protect(FLAG_PROTECT_SET,

board/eltec/bab7xx/flash.c

@@ -83,21 +83,21 @@ unsigned long flash_init (void)
     {
         (void)flash_protect(FLAG_PROTECT_SET,
                 FLASH_BASE0_PRELIM,
-                FLASH_BASE0_PRELIM+CFG_MONITOR_LEN-1,
+                FLASH_BASE0_PRELIM+monitor_flash_len-1,
                 &flash_info[0]);
     }
     if (size2 == 512*1024)
     {
         (void)flash_protect(FLAG_PROTECT_SET,
                 FLASH_BASE1_PRELIM,
-                FLASH_BASE1_PRELIM+CFG_MONITOR_LEN-1,
+                FLASH_BASE1_PRELIM+monitor_flash_len-1,
                 &flash_info[1]);
     }
     if (size2 == 4*1024*1024)
     {
         (void)flash_protect(FLAG_PROTECT_SET,
                 CFG_FLASH_BASE,
-                CFG_FLASH_BASE+CFG_MONITOR_LEN-1,
+                CFG_FLASH_BASE+monitor_flash_len-1,
                 &flash_info[1]);
     }
 

board/eltec/elppc/flash.c

@@ -83,21 +83,21 @@ unsigned long flash_init (void)
     {
         (void)flash_protect(FLAG_PROTECT_SET,
                 FLASH_BASE0_PRELIM,
-                FLASH_BASE0_PRELIM+CFG_MONITOR_LEN-1,
+                FLASH_BASE0_PRELIM+monitor_flash_len-1,
                 &flash_info[0]);
     }
     if (size2 == 512*1024)
     {
         (void)flash_protect(FLAG_PROTECT_SET,
                 FLASH_BASE1_PRELIM,
-                FLASH_BASE1_PRELIM+CFG_MONITOR_LEN-1,
+                FLASH_BASE1_PRELIM+monitor_flash_len-1,
                 &flash_info[1]);
     }
     if (size2 == 4*1024*1024)
     {
         (void)flash_protect(FLAG_PROTECT_SET,
                 CFG_FLASH_BASE,
-                CFG_FLASH_BASE+CFG_MONITOR_LEN-1,
+                CFG_FLASH_BASE+monitor_flash_len-1,
                 &flash_info[1]);
     }
 

board/eltec/mhpc/flash.c

@@ -92,7 +92,7 @@ unsigned long flash_init (void)
 	/* monitor protection ON by default */
 	(void)flash_protect(FLAG_PROTECT_SET,
 			    CFG_FLASH_BASE,
-			    CFG_FLASH_BASE+CFG_MONITOR_LEN-1,
+			    CFG_FLASH_BASE+monitor_flash_len-1,
 			    &flash_info[0]);
 
 	flash_info[0].size = size_b0;

board/ep7312/flash.c

@@ -61,7 +61,7 @@ ulong flash_init (void)
 	 */
 	flash_protect ( FLAG_PROTECT_SET,
 			CFG_FLASH_BASE,
-			CFG_FLASH_BASE + _armboot_end_data - _armboot_start,
+			CFG_FLASH_BASE + monitor_flash_len - 1,
 			&flash_info[0]);
 
 	flash_protect ( FLAG_PROTECT_SET,

board/ep8260/flash.c

@@ -140,7 +140,7 @@ unsigned long flash_init (void)
 #if CFG_MONITOR_BASE >= CFG_FLASH0_BASE
     flash_protect(FLAG_PROTECT_SET,
 		  CFG_MONITOR_BASE,
-		  CFG_MONITOR_BASE+CFG_MONITOR_LEN-1,
+		  CFG_MONITOR_BASE+monitor_flash_len-1,
 		  &flash_info[0]);
 #endif
 

board/eric/flash.c

@@ -83,13 +83,13 @@ unsigned long flash_init (void)
 	    /* Monitor protection ON by default */
 #if 0	    /* sand: */
 	    (void)flash_protect(FLAG_PROTECT_SET,
-				FLASH_BASE0_PRELIM-CFG_MONITOR_LEN+size_b0,
+				FLASH_BASE0_PRELIM-monitor_flash_len+size_b0,
 				FLASH_BASE0_PRELIM-1+size_b0,
 				&flash_info[0]);
 #else
 	    (void)flash_protect(FLAG_PROTECT_SET,
 		      		CFG_MONITOR_BASE,
-		      		CFG_MONITOR_BASE+CFG_MONITOR_LEN-1,
+		      		CFG_MONITOR_BASE+monitor_flash_len-1,
 		      		&flash_info[0]);
 #endif
 	    size_b1 = 0 ;
@@ -132,13 +132,13 @@ unsigned long flash_init (void)
 	    /* monitor protection ON by default */
 #if 0	    /* sand: */
 	    (void)flash_protect(FLAG_PROTECT_SET,
-				FLASH_BASE0_PRELIM-CFG_MONITOR_LEN+size_b0,
+				FLASH_BASE0_PRELIM-monitor_flash_len+size_b0,
 				FLASH_BASE0_PRELIM-1+size_b0,
 				&flash_info[0]);
 #else
 	    (void)flash_protect(FLAG_PROTECT_SET,
 		      		CFG_MONITOR_BASE,
-		      		CFG_MONITOR_BASE+CFG_MONITOR_LEN-1,
+		      		CFG_MONITOR_BASE+monitor_flash_len-1,
 		      		&flash_info[0]);
 #endif
 
@@ -150,12 +150,12 @@ unsigned long flash_init (void)
 
 	      /* monitor protection ON by default */
 	      (void)flash_protect(FLAG_PROTECT_SET,
-				  base_b1+size_b1-CFG_MONITOR_LEN,
+				  base_b1+size_b1-monitor_flash_len,
 				  base_b1+size_b1-1,
 				  &flash_info[1]);
 	      /* monitor protection OFF by default (one is enough) */
 	      (void)flash_protect(FLAG_PROTECT_CLEAR,
-				  base_b0+size_b0-CFG_MONITOR_LEN,
+				  base_b0+size_b0-monitor_flash_len,
 				  base_b0+size_b0-1,
 				  &flash_info[0]);
 	    } else {

board/esd/adciop/flash.c

@@ -80,7 +80,7 @@ unsigned long flash_init (void)
 
 	/* monitor protection ON by default */
 	flash_protect(FLAG_PROTECT_SET,
-		      FLASH_BASE0_PRELIM+size_b0-CFG_MONITOR_LEN,
+		      FLASH_BASE0_PRELIM+size_b0-monitor_flash_len,
 		      FLASH_BASE0_PRELIM+size_b0-1,
 		      &flash_info[0]);
 
@@ -93,12 +93,12 @@ unsigned long flash_init (void)
 
 		/* monitor protection ON by default */
 		flash_protect(FLAG_PROTECT_SET,
-			      FLASH_BASE0_PRELIM+size_b0+size_b1-CFG_MONITOR_LEN,
+			      FLASH_BASE0_PRELIM+size_b0+size_b1-monitor_flash_len,
 			      FLASH_BASE0_PRELIM+size_b0+size_b1-1,
 			      &flash_info[1]);
                 /* monitor protection OFF by default (one is enough) */
                 flash_protect(FLAG_PROTECT_CLEAR,
-			      FLASH_BASE0_PRELIM+size_b0-CFG_MONITOR_LEN,
+			      FLASH_BASE0_PRELIM+size_b0-monitor_flash_len,
 			      FLASH_BASE0_PRELIM+size_b0-1,
 			      &flash_info[0]);
 	} else {

board/esd/ar405/flash.c

@@ -94,7 +94,7 @@ unsigned long flash_init (void)
 
 	/* monitor protection ON by default */
 	(void)flash_protect(FLAG_PROTECT_SET,
-			    base_b0+size_b0-CFG_MONITOR_LEN,
+			    base_b0+size_b0-monitor_flash_len,
 			    base_b0+size_b0-1,
 			    &flash_info[0]);
 
@@ -106,12 +106,12 @@ unsigned long flash_init (void)
 
 		/* monitor protection ON by default */
 		(void)flash_protect(FLAG_PROTECT_SET,
-				    base_b1+size_b1-CFG_MONITOR_LEN,
+				    base_b1+size_b1-monitor_flash_len,
 				    base_b1+size_b1-1,
 				    &flash_info[1]);
                 /* monitor protection OFF by default (one is enough) */
                 (void)flash_protect(FLAG_PROTECT_CLEAR,
-                                    base_b0+size_b0-CFG_MONITOR_LEN,
+                                    base_b0+size_b0-monitor_flash_len,
                                     base_b0+size_b0-1,
                                     &flash_info[0]);
 	} else {

board/esd/ash405/Makefile

@@ -0,0 +1,46 @@
+#
+# (C) Copyright 2000
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	= $(BOARD).o flash.o
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) crv $@ $^
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+sinclude .depend
+
+#########################################################################

board/esd/ash405/ash405.c

@@ -0,0 +1,247 @@
+/*
+ * (C) Copyright 2001-2003
+ * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/processor.h>
+#include <command.h>
+#include <cmd_boot.h>
+#include <malloc.h>
+
+/* ------------------------------------------------------------------------- */
+
+#if 0
+#define FPGA_DEBUG
+#endif
+
+/* fpga configuration data - gzip compressed and generated by bin2c */
+const unsigned char fpgadata[] =
+{
+#include "fpgadata.c"
+};
+
+/*
+ * include common fpga code (for esd boards)
+ */
+#include "../common/fpga.c"
+
+
+/* Prototypes */
+int gunzip(void *, int, unsigned char *, int *);
+
+
+int board_pre_init (void)
+{
+	/*
+	 * IRQ 0-15  405GP internally generated; active high; level sensitive
+	 * IRQ 16    405GP internally generated; active low; level sensitive
+	 * IRQ 17-24 RESERVED
+	 * IRQ 25 (EXT IRQ 0) CAN0; active low; level sensitive
+	 * IRQ 26 (EXT IRQ 1) SER0 ; active low; level sensitive
+	 * IRQ 27 (EXT IRQ 2) SER1; active low; level sensitive
+	 * IRQ 28 (EXT IRQ 3) FPGA 0; active low; level sensitive
+	 * IRQ 29 (EXT IRQ 4) FPGA 1; active low; level sensitive
+	 * IRQ 30 (EXT IRQ 5) PCI INTA; active low; level sensitive
+	 * IRQ 31 (EXT IRQ 6) COMPACT FLASH; active high; level sensitive
+	 */
+	mtdcr(uicsr, 0xFFFFFFFF);       /* clear all ints */
+	mtdcr(uicer, 0x00000000);       /* disable all ints */
+	mtdcr(uiccr, 0x00000000);       /* set all to be non-critical*/
+	mtdcr(uicpr, 0xFFFFFF81);       /* set int polarities */
+	mtdcr(uictr, 0x10000000);       /* set int trigger levels */
+	mtdcr(uicvcr, 0x00000001);      /* set vect base=0,INT0 highest priority*/
+	mtdcr(uicsr, 0xFFFFFFFF);       /* clear all ints */
+
+	/*
+	 * EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 15 us
+	 */
+	mtebc (epcr, 0xa8400000); /* ebc always driven */
+
+	return 0;
+}
+
+
+/* ------------------------------------------------------------------------- */
+
+int misc_init_f (void)
+{
+	return 0;  /* dummy implementation */
+}
+
+
+int misc_init_r (void)
+{
+	volatile unsigned char *duart0_mcr = (unsigned char *)((ulong)DUART0_BA + 4);
+	volatile unsigned char *duart1_mcr = (unsigned char *)((ulong)DUART1_BA + 4);
+	volatile unsigned char *duart2_mcr = (unsigned char *)((ulong)DUART2_BA + 4);
+	volatile unsigned char *duart3_mcr = (unsigned char *)((ulong)DUART3_BA + 4);
+	unsigned char *dst;
+	ulong len = sizeof(fpgadata);
+	int status;
+	int index;
+	int i;
+
+	dst = malloc(CFG_FPGA_MAX_SIZE);
+	if (gunzip (dst, CFG_FPGA_MAX_SIZE, (uchar *)fpgadata, (int *)&len) != 0) {
+		printf ("GUNZIP ERROR - must RESET board to recover\n");
+		do_reset (NULL, 0, 0, NULL);
+	}
+
+	status = fpga_boot(dst, len);
+	if (status != 0) {
+		printf("\nFPGA: Booting failed ");
+		switch (status) {
+		case ERROR_FPGA_PRG_INIT_LOW:
+			printf("(Timeout: INIT not low after asserting PROGRAM*)\n ");
+			break;
+		case ERROR_FPGA_PRG_INIT_HIGH:
+			printf("(Timeout: INIT not high after deasserting PROGRAM*)\n ");
+			break;
+		case ERROR_FPGA_PRG_DONE:
+			printf("(Timeout: DONE not high after programming FPGA)\n ");
+			break;
+		}
+
+		/* display infos on fpgaimage */
+		index = 15;
+		for (i=0; i<4; i++) {
+			len = dst[index];
+			printf("FPGA: %s\n", &(dst[index+1]));
+			index += len+3;
+		}
+		putc ('\n');
+		/* delayed reboot */
+		for (i=20; i>0; i--) {
+			printf("Rebooting in %2d seconds \r",i);
+			for (index=0;index<1000;index++)
+				udelay(1000);
+		}
+		putc ('\n');
+		do_reset(NULL, 0, 0, NULL);
+	}
+
+	puts("FPGA:  ");
+
+	/* display infos on fpgaimage */
+	index = 15;
+	for (i=0; i<4; i++) {
+		len = dst[index];
+		printf("%s ", &(dst[index+1]));
+		index += len+3;
+	}
+	putc ('\n');
+
+	free(dst);
+
+	/*
+	 * Reset FPGA via FPGA_DATA pin
+	 */
+	SET_FPGA(FPGA_PRG | FPGA_CLK);
+	udelay(1000); /* wait 1ms */
+	SET_FPGA(FPGA_PRG | FPGA_CLK | FPGA_DATA);
+	udelay(1000); /* wait 1ms */
+
+	/*
+	 * Reset external DUARTs
+	 */
+	out32(GPIO0_OR, in32(GPIO0_OR) | CFG_DUART_RST); /* set reset to high */
+	udelay(10); /* wait 10us */
+	out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_DUART_RST); /* set reset to low */
+	udelay(1000); /* wait 1ms */
+
+	/*
+	 * Set NAND-FLASH GPIO signals to default
+	 */
+	out32(GPIO0_OR, in32(GPIO0_OR) & ~(CFG_NAND_CLE | CFG_NAND_ALE));
+	out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);
+
+	/*
+	 * Enable interrupts in exar duart mcr[3]
+	 */
+	*duart0_mcr = 0x08;
+	*duart1_mcr = 0x08;
+	*duart2_mcr = 0x08;
+	*duart3_mcr = 0x08;
+
+	return (0);
+}
+
+
+/*
+ * Check Board Identity:
+ */
+
+int checkboard (void)
+{
+	unsigned char str[64];
+	int i = getenv_r ("serial#", str, sizeof(str));
+
+	puts ("Board: ");
+
+	if (i == -1) {
+		puts ("### No HW ID - assuming ASH405");
+	} else {
+		puts(str);
+	}
+
+	putc ('\n');
+
+	return 0;
+}
+
+/* ------------------------------------------------------------------------- */
+
+long int initdram (int board_type)
+{
+	unsigned long val;
+
+	mtdcr(memcfga, mem_mb0cf);
+	val = mfdcr(memcfgd);
+
+#if 0
+	printf("\nmb0cf=%x\n", val); /* test-only */
+	printf("strap=%x\n", mfdcr(strap)); /* test-only */
+#endif
+
+	return (4*1024*1024 << ((val & 0x000e0000) >> 17));
+}
+
+/* ------------------------------------------------------------------------- */
+
+int testdram (void)
+{
+	/* TODO: XXX XXX XXX */
+	printf ("test: 16 MB - ok\n");
+
+	return (0);
+}
+
+/* ------------------------------------------------------------------------- */
+
+#if (CONFIG_COMMANDS & CFG_CMD_NAND)
+extern void nand_probe(ulong physadr);
+void nand_init(void)
+{
+	printf("Probing at 0x%.8x\n", CFG_NAND_BASE);
+	nand_probe(CFG_NAND_BASE);
+}
+#endif

board/esd/ash405/config.mk

@@ -0,0 +1,28 @@
+#
+# (C) Copyright 2000
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# esd ASH405 boards
+#
+
+TEXT_BASE = 0xFFFC0000

board/esd/ash405/flash.c

@@ -0,0 +1,101 @@
+/*
+ * (C) Copyright 2001
+ * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <ppc4xx.h>
+#include <asm/processor.h>
+
+/*
+ * include common flash code (for esd boards)
+ */
+#include "../common/flash.c"
+
+/*-----------------------------------------------------------------------
+ * Functions
+ */
+static ulong flash_get_size (vu_long * addr, flash_info_t * info);
+static void flash_get_offsets (ulong base, flash_info_t * info);
+
+/*-----------------------------------------------------------------------
+ */
+
+unsigned long flash_init (void)
+{
+	unsigned long size_b0;
+	int i;
+        uint pbcr;
+        unsigned long base_b0;
+	int size_val = 0;
+
+	/* Init: no FLASHes known */
+	for (i=0; i<CFG_MAX_FLASH_BANKS; ++i) {
+		flash_info[i].flash_id = FLASH_UNKNOWN;
+	}
+
+	/* Static FLASH Bank configuration here - FIXME XXX */
+
+	size_b0 = flash_get_size((vu_long *)FLASH_BASE0_PRELIM, &flash_info[0]);
+
+	if (flash_info[0].flash_id == FLASH_UNKNOWN) {
+		printf ("## Unknown FLASH on Bank 0 - Size = 0x%08lx = %ld MB\n",
+			size_b0, size_b0<<20);
+	}
+
+        /* Setup offsets */
+        flash_get_offsets (-size_b0, &flash_info[0]);
+
+        /* Re-do sizing to get full correct info */
+        mtdcr(ebccfga, pb0cr);
+        pbcr = mfdcr(ebccfgd);
+        mtdcr(ebccfga, pb0cr);
+        base_b0 = -size_b0;
+	switch (size_b0) {
+	case 1 << 20:
+		size_val = 0;
+		break;
+	case 2 << 20:
+		size_val = 1;
+		break;
+	case 4 << 20:
+		size_val = 2;
+		break;
+	case 8 << 20:
+		size_val = 3;
+		break;
+	case 16 << 20:
+		size_val = 4;
+		break;
+	}
+	pbcr = (pbcr & 0x0001ffff) | base_b0 | (size_val << 17);
+        mtdcr(ebccfgd, pbcr);
+
+        /* Monitor protection ON by default */
+        (void)flash_protect(FLAG_PROTECT_SET,
+                            -CFG_MONITOR_LEN,
+                            0xffffffff,
+                            &flash_info[0]);
+
+        flash_info[0].size = size_b0;
+
+	return (size_b0);
+}

board/esd/ash405/u-boot.lds

@@ -0,0 +1,142 @@
+/*
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+/* Do we need any of these for elf?
+   __DYNAMIC = 0;    */
+SECTIONS
+{
+  .resetvec 0xFFFFFFFC :
+  {
+    *(.resetvec)
+  } = 0xffff
+
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)		}
+  .rela.text     : { *(.rela.text) 	}
+  .rel.data      : { *(.rel.data)		}
+  .rela.data     : { *(.rela.data) 	}
+  .rel.rodata    : { *(.rel.rodata) 	}
+  .rela.rodata   : { *(.rela.rodata) 	}
+  .rel.got       : { *(.rel.got)		}
+  .rela.got      : { *(.rela.got)		}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)		}
+  .rela.bss      : { *(.rela.bss)		}
+  .rel.plt       : { *(.rel.plt)		}
+  .rela.plt      : { *(.rela.plt)		}
+  .init          : { *(.init)	}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    /* WARNING - the following is hand-optimized to fit within	*/
+    /* the sector layout of our flash chips!	XXX FIXME XXX	*/
+
+    cpu/ppc4xx/start.o	(.text)
+    cpu/ppc4xx/traps.o	(.text)
+    cpu/ppc4xx/interrupts.o	(.text)
+    cpu/ppc4xx/serial.o	(.text)
+    cpu/ppc4xx/cpu_init.o	(.text)
+    cpu/ppc4xx/speed.o	(.text)
+    cpu/ppc4xx/405gp_enet.o	(.text)
+    common/dlmalloc.o	(.text)
+    lib_generic/crc32.o		(.text)
+    lib_ppc/extable.o	(.text)
+    lib_generic/zlib.o		(.text)
+
+/*    . = env_offset;*/
+/*    common/environment.o(.text)*/
+
+    *(.text)
+    *(.fixup)
+    *(.got1)
+  }
+  _etext = .;
+  PROVIDE (etext = .);
+  .rodata    :
+  {
+    *(.rodata)
+    *(.rodata1)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x00FF) & 0xFFFFFF00;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
+  __fixup_entries = (. - _FIXUP_TABLE_)>>2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(256);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(256);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+  _end = . ;
+  PROVIDE (end = .);
+}

board/esd/canbt/canbt.c

@@ -114,9 +114,9 @@ int board_pre_init (void)
 	/*
 	 * Setup port pins for normal operation
 	 */
-	out32 (IBM405GP_GPIO0_ODR, 0x00000000);	/* no open drain pins */
-	out32 (IBM405GP_GPIO0_TCR, 0x07038100);	/* setup for output */
-	out32 (IBM405GP_GPIO0_OR, 0x07030100);	/* set output pins to high (default) */
+	out32 (GPIO0_ODR, 0x00000000);	/* no open drain pins */
+	out32 (GPIO0_TCR, 0x07038100);	/* setup for output */
+	out32 (GPIO0_OR, 0x07030100);	/* set output pins to high (default) */
 
 	/*
 	 * IRQ 0-15  405GP internally generated; active high; level sensitive

board/esd/canbt/flash.c

@@ -74,7 +74,7 @@ unsigned long flash_init (void)
 
         /* Monitor protection ON by default */
         (void)flash_protect(FLAG_PROTECT_SET,
-                            -CFG_MONITOR_LEN,
+                            -monitor_flash_len,
                             0xffffffff,
                             &flash_info[0]);
 

board/esd/common/fpga.c

@@ -1,5 +1,5 @@
 /*
- * (C) Copyright 2001
+ * (C) Copyright 2001-2003
  * Matthias Fuchs, esd gmbh germany, matthias.fuchs@esd-electronics.com
  * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
  *
@@ -36,11 +36,6 @@
 
 #define MAX_ONES               226
 
-#define IBM405GP_GPIO0_OR      0xef600700  /* GPIO Output */
-#define IBM405GP_GPIO0_TCR     0xef600704  /* GPIO Three-State Control */
-#define IBM405GP_GPIO0_ODR     0xef600718  /* GPIO Open Drain */
-#define IBM405GP_GPIO0_IR      0xef60071c  /* GPIO Input */
-
 #ifdef CFG_FPGA_PRG
 # define FPGA_PRG              CFG_FPGA_PRG /* FPGA program pin (ppc output)*/
 # define FPGA_CLK              CFG_FPGA_CLK /* FPGA clk pin (ppc output)    */
@@ -59,7 +54,7 @@
 #define ERROR_FPGA_PRG_INIT_HIGH -2        /* Timeout after PRG* deasserted */
 #define ERROR_FPGA_PRG_DONE      -3        /* Timeout after programming     */
 
-#define SET_FPGA(data)         out32(IBM405GP_GPIO0_OR, data)
+#define SET_FPGA(data)         out32(GPIO0_OR, data)
 
 #define FPGA_WRITE_1 {                                                    \
         SET_FPGA(FPGA_PRG |            FPGA_DATA);  /* set clock to 0 */  \
@@ -120,12 +115,12 @@ static int fpga_boot(unsigned char *fpgadata, int size)
   /*
    * Setup port pins for fpga programming
    */
-  out32(IBM405GP_GPIO0_ODR, 0x00000000);                       /* no open drain pins      */
-  out32(IBM405GP_GPIO0_TCR, FPGA_PRG | FPGA_CLK | FPGA_DATA);  /* setup for output        */
-  out32(IBM405GP_GPIO0_OR,  FPGA_PRG | FPGA_CLK | FPGA_DATA);  /* set output pins to high */
+  out32(GPIO0_ODR, 0x00000000);                                      /* no open drain pins */
+  out32(GPIO0_TCR, in32(GPIO0_TCR) | FPGA_PRG | FPGA_CLK | FPGA_DATA); /* setup for output */
+  out32(GPIO0_OR, in32(GPIO0_OR) | FPGA_PRG | FPGA_CLK | FPGA_DATA);   /* set pins to high */
 
-  DBG("%s, ",((in32(IBM405GP_GPIO0_IR) & FPGA_DONE) == 0) ? "NOT DONE" : "DONE" );
-  DBG("%s\n",((in32(IBM405GP_GPIO0_IR) & FPGA_INIT) == 0) ? "NOT INIT" : "INIT" );
+  DBG("%s, ",((in32(GPIO0_IR) & FPGA_DONE) == 0) ? "NOT DONE" : "DONE" );
+  DBG("%s\n",((in32(GPIO0_IR) & FPGA_INIT) == 0) ? "NOT INIT" : "INIT" );
 
   /*
    * Init fpga by asserting and deasserting PROGRAM*
@@ -134,7 +129,7 @@ static int fpga_boot(unsigned char *fpgadata, int size)
 
   /* Wait for FPGA init line low */
   count = 0;
-  while (in32(IBM405GP_GPIO0_IR) & FPGA_INIT)
+  while (in32(GPIO0_IR) & FPGA_INIT)
     {
       udelay(1000); /* wait 1ms */
       /* Check for timeout - 100us max, so use 3ms */
@@ -145,15 +140,15 @@ static int fpga_boot(unsigned char *fpgadata, int size)
         }
     }
 
-  DBG("%s, ",((in32(IBM405GP_GPIO0_IR) & FPGA_DONE) == 0) ? "NOT DONE" : "DONE" );
-  DBG("%s\n",((in32(IBM405GP_GPIO0_IR) & FPGA_INIT) == 0) ? "NOT INIT" : "INIT" );
+  DBG("%s, ",((in32(GPIO0_IR) & FPGA_DONE) == 0) ? "NOT DONE" : "DONE" );
+  DBG("%s\n",((in32(GPIO0_IR) & FPGA_INIT) == 0) ? "NOT INIT" : "INIT" );
 
   /* deassert PROGRAM* */
   SET_FPGA(FPGA_PRG | FPGA_CLK | FPGA_DATA);
 
   /* Wait for FPGA end of init period .  */
   count = 0;
-  while (!(in32(IBM405GP_GPIO0_IR) & FPGA_INIT))
+  while (!(in32(GPIO0_IR) & FPGA_INIT))
     {
       udelay(1000); /* wait 1ms */
       /* Check for timeout */
@@ -164,8 +159,8 @@ static int fpga_boot(unsigned char *fpgadata, int size)
         }
     }
 
-  DBG("%s, ",((in32(IBM405GP_GPIO0_IR) & FPGA_DONE) == 0) ? "NOT DONE" : "DONE" );
-  DBG("%s\n",((in32(IBM405GP_GPIO0_IR) & FPGA_INIT) == 0) ? "NOT INIT" : "INIT" );
+  DBG("%s, ",((in32(GPIO0_IR) & FPGA_DONE) == 0) ? "NOT DONE" : "DONE" );
+  DBG("%s\n",((in32(GPIO0_IR) & FPGA_INIT) == 0) ? "NOT INIT" : "INIT" );
 
   DBG("write configuration data into fpga\n");
   /* write configuration-data into fpga... */
@@ -237,8 +232,8 @@ static int fpga_boot(unsigned char *fpgadata, int size)
     }
 #endif
 
-  DBG("%s, ",((in32(IBM405GP_GPIO0_IR) & FPGA_DONE) == 0) ? "NOT DONE" : "DONE" );
-  DBG("%s\n",((in32(IBM405GP_GPIO0_IR) & FPGA_INIT) == 0) ? "NOT INIT" : "INIT" );
+  DBG("%s, ",((in32(GPIO0_IR) & FPGA_DONE) == 0) ? "NOT DONE" : "DONE" );
+  DBG("%s\n",((in32(GPIO0_IR) & FPGA_INIT) == 0) ? "NOT INIT" : "INIT" );
 
   /*
    * Check if fpga's DONE signal - correctly booted ?
@@ -246,7 +241,7 @@ static int fpga_boot(unsigned char *fpgadata, int size)
 
   /* Wait for FPGA end of programming period .  */
   count = 0;
-  while (!(in32(IBM405GP_GPIO0_IR) & FPGA_DONE))
+  while (!(in32(GPIO0_IR) & FPGA_DONE))
     {
       udelay(1000); /* wait 1ms */
       /* Check for timeout */

board/esd/cpci405/config.mk

@@ -28,5 +28,9 @@
 ifeq ($(BOARD_REVISION),CPCI4052)
 TEXT_BASE = 0xFFFC0000
 else
+ifeq ($(BOARD_REVISION),CPCI405AB)
+TEXT_BASE = 0xFFFC0000
+else
 TEXT_BASE = 0xFFFD0000
 endif
+endif

board/esd/cpci405/cpci405.c

@@ -37,7 +37,11 @@
 const unsigned char fpgadata[] =
 {
 #ifdef CONFIG_CPCI405_VER2
-# include "fpgadata_cpci4052.c"
+# ifdef CONFIG_CPCI405AB
+#  include "fpgadata_cpci405ab.c"
+# else
+#  include "fpgadata_cpci4052.c"
+# endif
 #else
 # include "fpgadata_cpci405.c"
 #endif
@@ -74,10 +78,10 @@ int board_pre_init (void)
 	/*
 	 * First pull fpga-prg pin low, to disable fpga logic (on version 2 board)
 	 */
-	out32(IBM405GP_GPIO0_ODR, 0x00000000);        /* no open drain pins      */
-	out32(IBM405GP_GPIO0_TCR, CFG_FPGA_PRG);      /* setup for output        */
-	out32(IBM405GP_GPIO0_OR,  CFG_FPGA_PRG);      /* set output pins to high */
-	out32(IBM405GP_GPIO0_OR, 0);                  /* pull prg low            */
+	out32(GPIO0_ODR, 0x00000000);        /* no open drain pins      */
+	out32(GPIO0_TCR, CFG_FPGA_PRG);      /* setup for output        */
+	out32(GPIO0_OR,  CFG_FPGA_PRG);      /* set output pins to high */
+	out32(GPIO0_OR, 0);                  /* pull prg low            */
 
 	/*
 	 * Boot onboard FPGA
@@ -192,10 +196,10 @@ int cpci405_version(void)
 	 */
 	cntrl0Reg = mfdcr(cntrl0);
 	mtdcr(cntrl0, cntrl0Reg | 0x03000000);
-	out32(IBM405GP_GPIO0_ODR, in32(IBM405GP_GPIO0_ODR) & ~0x00180000);
-	out32(IBM405GP_GPIO0_TCR, in32(IBM405GP_GPIO0_TCR) & ~0x00180000);
+	out32(GPIO0_ODR, in32(GPIO0_ODR) & ~0x00180000);
+	out32(GPIO0_TCR, in32(GPIO0_TCR) & ~0x00180000);
 	udelay(1000);                   /* wait some time before reading input */
-	value = in32(IBM405GP_GPIO0_IR) & 0x00180000;       /* get config bits */
+	value = in32(GPIO0_IR) & 0x00180000;       /* get config bits */
 
 	/*
 	 * Restore GPIO settings
@@ -505,4 +509,44 @@ void ide_set_reset(int on)
 #endif /* CONFIG_IDE_RESET */
 #endif /* CONFIG_CPCI405_VER2 */
 
+#if 0 /* test-only */
 /* ------------------------------------------------------------------------- */
+
+u8 *dhcp_vendorex_prep (u8 * e)
+{
+	char *ptr;
+
+/* DHCP vendor-class-identifier = 60 */
+	if ((ptr = getenv ("dhcp_vendor-class-identifier"))) {
+		*e++ = 60;
+		*e++ = strlen (ptr);
+		while (*ptr)
+			*e++ = *ptr++;
+	}
+/* my DHCP_CLIENT_IDENTIFIER = 61 */
+	if ((ptr = getenv ("dhcp_client_id"))) {
+		*e++ = 61;
+		*e++ = strlen (ptr);
+		while (*ptr)
+			*e++ = *ptr++;
+	}
+
+	return e;
+}
+
+
+/* ------------------------------------------------------------------------- */
+
+u8 *dhcp_vendorex_proc (u8 * popt)
+{
+	if (*popt == 61)
+		return (u8 *)-1;
+	if (*popt == 43) {
+		printf("|%s|", popt+4); /* test-only */
+		return (u8 *)-1;
+	}
+	return NULL;
+}
+
+/* ------------------------------------------------------------------------- */
+#endif /* test-only */

board/esd/cpci405/flash.c

@@ -86,11 +86,11 @@ unsigned long flash_init (void)
 	/* Re-do sizing to get full correct info */
 
 	if (size_b1) {
-		base_b1 = -size_b1;
 		if (size_b1 < (1 << 20)) {
 			/* minimum CS size on PPC405GP is 1MB !!! */
 			size_b1 = 1 << 20;
 		}
+		base_b1 = -size_b1;
 		mtdcr (ebccfga, pb0cr);
 		pbcr = mfdcr (ebccfgd);
 		mtdcr (ebccfga, pb0cr);
@@ -103,11 +103,11 @@ unsigned long flash_init (void)
 	}
 
 	if (size_b0) {
-		base_b0 = base_b1 - size_b0;
 		if (size_b0 < (1 << 20)) {
 			/* minimum CS size on PPC405GP is 1MB !!! */
 			size_b0 = 1 << 20;
 		}
+		base_b0 = base_b1 - size_b0;
 		mtdcr (ebccfga, pb1cr);
 		pbcr = mfdcr (ebccfgd);
 		mtdcr (ebccfga, pb1cr);
@@ -125,7 +125,7 @@ unsigned long flash_init (void)
 
 	/* monitor protection ON by default */
 	flash_protect (FLAG_PROTECT_SET,
-			base_b0 + size_b0 - CFG_MONITOR_LEN,
+			base_b0 + size_b0 - monitor_flash_len,
 			base_b0 + size_b0 - 1, &flash_info[0]);
 
 	if (size_b1) {
@@ -136,11 +136,11 @@ unsigned long flash_init (void)
 
 		/* monitor protection ON by default */
 		flash_protect (FLAG_PROTECT_SET,
-				base_b1 + size_b1 - CFG_MONITOR_LEN,
+				base_b1 + size_b1 - monitor_flash_len,
 				base_b1 + size_b1 - 1, &flash_info[1]);
 		/* monitor protection OFF by default (one is enough) */
 		flash_protect (FLAG_PROTECT_CLEAR,
-				base_b0 + size_b0 - CFG_MONITOR_LEN,
+				base_b0 + size_b0 - monitor_flash_len,
 				base_b0 + size_b0 - 1, &flash_info[0]);
 	} else {
 		flash_info[1].flash_id = FLASH_UNKNOWN;

board/esd/cpci440/strataflash.c

@@ -200,7 +200,7 @@ unsigned long flash_init (void)
 #if 0 /* test-only */
 	/* Monitor protection ON by default */
 #if (CFG_MONITOR_BASE >= CFG_FLASH_BASE)
-	for(i=0; flash_info[0].start[i] < CFG_MONITOR_BASE+CFG_MONITOR_LEN-1; i++)
+	for(i=0; flash_info[0].start[i] < CFG_MONITOR_BASE+monitor_flash_len-1; i++)
 		(void)flash_real_protect(&flash_info[0], i, 1);
 #endif
 #endif

board/esd/cpciiser4/flash.c

@@ -74,7 +74,7 @@ unsigned long flash_init (void)
 
         /* Monitor protection ON by default */
         (void)flash_protect(FLAG_PROTECT_SET,
-                            -CFG_MONITOR_LEN,
+                            -monitor_flash_len,
                             0xffffffff,
                             &flash_info[0]);
 

board/esd/dasa_sim/flash.c

@@ -67,7 +67,7 @@ unsigned long flash_init (void)
 
         /* Monitor protection ON by default */
         (void)flash_protect(FLAG_PROTECT_SET,
-                            -CFG_MONITOR_LEN,
+                            -monitor_flash_len,
                             0xffffffff,
                             &flash_info[0]);
 

board/esd/du405/flash.c

@@ -94,7 +94,7 @@ unsigned long flash_init (void)
 
 	/* monitor protection ON by default */
 	flash_protect (FLAG_PROTECT_SET,
-			base_b0 + size_b0 - CFG_MONITOR_LEN,
+			base_b0 + size_b0 - monitor_flash_len,
 			base_b0 + size_b0 - 1, &flash_info[0]);
 
 	if (size_b1) {
@@ -105,11 +105,11 @@ unsigned long flash_init (void)
 
 		/* monitor protection ON by default */
 		flash_protect (FLAG_PROTECT_SET,
-				base_b1 + size_b1 - CFG_MONITOR_LEN,
+				base_b1 + size_b1 - monitor_flash_len,
 				base_b1 + size_b1 - 1, &flash_info[1]);
 		/* monitor protection OFF by default (one is enough) */
 		flash_protect (FLAG_PROTECT_CLEAR,
-				base_b0 + size_b0 - CFG_MONITOR_LEN,
+				base_b0 + size_b0 - monitor_flash_len,
 				base_b0 + size_b0 - 1, &flash_info[0]);
 	} else {
 		flash_info[1].flash_id = FLASH_UNKNOWN;

board/esd/ocrtc/flash.c

@@ -127,7 +127,7 @@ unsigned long flash_init (void)
 
 	/* monitor protection ON by default */
 	flash_protect (FLAG_PROTECT_SET,
-			base_b0 + size_b0 - CFG_MONITOR_LEN,
+			base_b0 + size_b0 - monitor_flash_len,
 			base_b0 + size_b0 - 1, &flash_info[0]);
 
 	if (size_b1) {
@@ -138,11 +138,11 @@ unsigned long flash_init (void)
 
 		/* monitor protection ON by default */
 		flash_protect (FLAG_PROTECT_SET,
-				base_b1 + size_b1 - CFG_MONITOR_LEN,
+				base_b1 + size_b1 - monitor_flash_len,
 				base_b1 + size_b1 - 1, &flash_info[1]);
 		/* monitor protection OFF by default (one is enough) */
 		flash_protect (FLAG_PROTECT_CLEAR,
-				base_b0 + size_b0 - CFG_MONITOR_LEN,
+				base_b0 + size_b0 - monitor_flash_len,
 				base_b0 + size_b0 - 1, &flash_info[0]);
 	} else {
 		flash_info[1].flash_id = FLASH_UNKNOWN;

board/esd/pci405/cmd_pci405.c

@@ -36,66 +36,7 @@
 
 extern int do_bootm (cmd_tbl_t *, int, int, char *[]);
 
-#if 0 /* test-only */
-#include "../common/fpga.c"
-void error_print(void)
-{
-	int i;
-	volatile unsigned char *ptr;
-	volatile unsigned long *ptr2;
-	
-	printf("\n 2nd SJA1000:\n");
-	ptr = 0xf0000100;
-	for (i=0; i<0x20; i++) {
-		printf("%02x ", *ptr++);
-	}
 
-	ptr2 = 0xf0400008;
-	printf("\nTimestamp = %x\n", *ptr2);
-	udelay(1000);
-	printf("Timestamp = %x\n", *ptr2);
-	udelay(1000);
-	printf("Timestamp = %x\n", *ptr2);
-
-#if 0 /* test-only */
-	/*
-	 * Reset FPGA via FPGA_DATA pin
-	 */
-	printf("Resetting FPGA...\n");
-	SET_FPGA(FPGA_PRG | FPGA_CLK);
-	udelay(1000); /* wait 1ms */
-	SET_FPGA(FPGA_PRG | FPGA_CLK | FPGA_DATA);
-	udelay(1000); /* wait 1ms */
-
-	do_loadpci(NULL, 0,0, NULL);
-#endif
-}
-
-void read_loop(void)
-{
-	int i;
-	volatile unsigned char *ptr;
-	volatile unsigned char val;
-	volatile unsigned long *ptr2;
-
-	printf("\nread loop on 1st sja1000...");
-	while (1) {
-		ptr = 0xf0000000;
-/*		printf("\n1st SJA1000:\n");*/
-		for (i=0; i<0x20; i++) {
-			i = i;
-			val = *ptr++;
-/*			printf("%02x ", val);*/
-		}
-
-		/* Abort if ctrl-c was pressed */
-		if (ctrlc()) {
-			puts("\nAbort\n");
-			return 0;
-		}
-	}
-}
-#endif
 /*
  * Command loadpci: wait for signal from host and boot image.
  */
@@ -110,66 +51,6 @@ int do_loadpci(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 	char str[] = "\\|/-";
 	char *local_args[2];
 
-#if 0 /* test-only */
-	puts("\nStarting sja1000 test...");
-	{
-		int count;
-		volatile unsigned char *ptr;
-		volatile unsigned char val;
-		volatile unsigned char val2;
-
-#if 1 /* write test */
-		ptr = 0xf0000014;
-		for (i=1; i<11; i++)
-			*ptr++ = i;
-#endif
-		
-		count = 0;
-		while (1) {
-			count++;
-#if 0 /* write test */
-			ptr = 0xf0000014;
-			for (i=1; i<11; i++)
-				*ptr++ = i;
-#endif
-#if 1 /* read test */
-			ptr = 0xf0000014;
-			for (i=1; i<11; i++) {
-				val = *ptr++;
-#if 1
-				if (val != i) {
-					ptr = 0xf0000100;
-					val = *ptr; /* trigger las */
-
-					ptr = 0xf0000014;
-					val2 = *ptr;
-
-					printf("\nERROR: count=%d: soll=%x ist=%x -> staring read loop on 1st sja1000...\n",	count, i, val);
-
-					printf("soll=%x ist=%x -> staring read loop on 1st sja1000...\n", 1, val2);
-
-					return 0; /* test-only */
-					udelay(1000);
-					error_print();
-					read_loop();
-					return 0;
-				}
-#endif
-			}
-#endif
-
-			/* Abort if ctrl-c was pressed */
-			if (ctrlc()) {
-				puts("\nAbort\n");
-				return 0;
-			}
-
-			if (!(count % 100000)) {
-				printf(".");
-			}
-		}
-	}
-#endif
 	/*
 	 * Mark sync address
 	 */
@@ -212,13 +93,13 @@ int do_loadpci(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 		printf("\nStoring PCI Configuration Regs...\n");
 	} else {
 		sprintf(addr, "%08x", *ptr);
-		
+
 		/*
 		 * Boot image
 		 */
 		printf("\nBooting image at addr 0x%s ...\n", addr);
 		setenv("loadaddr", addr);
-		
+
 		local_args[0] = argv[0];
 		local_args[1] = NULL;
 		status = do_bootm (cmdtp, 0, 1, local_args);

board/esd/pci405/flash.c

@@ -91,7 +91,7 @@ unsigned long flash_init (void)
 
         /* Monitor protection ON by default */
         (void)flash_protect(FLAG_PROTECT_SET,
-                            -CFG_MONITOR_LEN,
+                            -monitor_flash_len,
                             0xffffffff,
                             &flash_info[0]);
 

board/esd/pci405/pci405.c

@@ -84,6 +84,11 @@ int board_pre_init (void)
 	cntrl0Reg = mfdcr(cntrl0);
 	mtdcr(cntrl0, cntrl0Reg | 0x00008000);
 
+	/*
+	 * EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 25 us
+	 */
+	mtebc (epcr, 0xa8400000); /* ebc always driven */
+
 	return 0;
 }
 
@@ -186,7 +191,7 @@ int misc_init_r (void)
 			}
 		}
 		mtdcr(uicsr, 0xFFFFFFFF);        /* clear all ints */
-		
+
 		*magic = 0;      /* clear pci reconfig magic again */
 	}
 

board/esd/pmc405/Makefile

@@ -0,0 +1,46 @@
+#
+# (C) Copyright 2000, 2001
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	= $(BOARD).o strataflash.o
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) crv $@ $^
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+sinclude .depend
+
+#########################################################################

board/esd/pmc405/config.mk

@@ -0,0 +1,28 @@
+#
+# (C) Copyright 2000, 2001
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# esd PMC405 boards
+#
+
+TEXT_BASE = 0xFFFC0000

board/esd/pmc405/pmc405.c

@@ -0,0 +1,229 @@
+/*
+ * (C) Copyright 2001-2003
+ * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/processor.h>
+#include <command.h>
+#include <cmd_boot.h>
+#include <malloc.h>
+
+/* ------------------------------------------------------------------------- */
+
+
+/* Prototypes */
+int gunzip(void *, int, unsigned char *, int *);
+
+
+int board_pre_init (void)
+{
+	/*
+	 * IRQ 0-15  405GP internally generated; active high; level sensitive
+	 * IRQ 16    405GP internally generated; active low; level sensitive
+	 * IRQ 17-24 RESERVED
+	 * IRQ 25 (EXT IRQ 0) CAN0; active low; level sensitive
+	 * IRQ 26 (EXT IRQ 1) SER0 ; active low; level sensitive
+	 * IRQ 27 (EXT IRQ 2) SER1; active low; level sensitive
+	 * IRQ 28 (EXT IRQ 3) FPGA 0; active low; level sensitive
+	 * IRQ 29 (EXT IRQ 4) FPGA 1; active low; level sensitive
+	 * IRQ 30 (EXT IRQ 5) PCI INTA; active low; level sensitive
+	 * IRQ 31 (EXT IRQ 6) COMPACT FLASH; active high; level sensitive
+	 */
+	mtdcr(uicsr, 0xFFFFFFFF);       /* clear all ints */
+	mtdcr(uicer, 0x00000000);       /* disable all ints */
+	mtdcr(uiccr, 0x00000000);       /* set all to be non-critical*/
+	mtdcr(uicpr, 0xFFFFFF81);       /* set int polarities */
+	mtdcr(uictr, 0x10000000);       /* set int trigger levels */
+	mtdcr(uicvcr, 0x00000001);      /* set vect base=0,INT0 highest priority*/
+	mtdcr(uicsr, 0xFFFFFFFF);       /* clear all ints */
+
+	/*
+	 * EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 15 us
+	 */
+	mtebc (epcr, 0xa8400000);
+
+	return 0;
+}
+
+
+/* ------------------------------------------------------------------------- */
+
+int misc_init_f (void)
+{
+	return 0;  /* dummy implementation */
+}
+
+
+int misc_init_r (void)
+{
+#if 0 /* test-only */
+	DECLARE_GLOBAL_DATA_PTR;
+	volatile unsigned short *fpga_mode =
+		(unsigned short *)((ulong)CFG_FPGA_BASE_ADDR + CFG_FPGA_CTRL);
+	volatile unsigned char *duart0_mcr =
+		(unsigned char *)((ulong)DUART0_BA + 4);
+	volatile unsigned char *duart1_mcr =
+		(unsigned char *)((ulong)DUART1_BA + 4);
+	bd_t *bd = gd->bd;
+	char *	tmp;                    /* Temporary char pointer      */
+	unsigned char *dst;
+	ulong len = sizeof(fpgadata);
+	int status;
+	int index;
+	int i;
+	unsigned long cntrl0Reg;
+
+	/*
+	 * Setup GPIO pins (CS6+CS7 as GPIO)
+	 */
+	cntrl0Reg = mfdcr(cntrl0);
+	mtdcr(cntrl0, cntrl0Reg | 0x00300000);
+
+	dst = malloc(CFG_FPGA_MAX_SIZE);
+	if (gunzip (dst, CFG_FPGA_MAX_SIZE, (uchar *)fpgadata, (int *)&len) != 0) {
+		printf ("GUNZIP ERROR - must RESET board to recover\n");
+		do_reset (NULL, 0, 0, NULL);
+	}
+
+	status = fpga_boot(dst, len);
+	if (status != 0) {
+		printf("\nFPGA: Booting failed ");
+		switch (status) {
+		case ERROR_FPGA_PRG_INIT_LOW:
+			printf("(Timeout: INIT not low after asserting PROGRAM*)\n ");
+			break;
+		case ERROR_FPGA_PRG_INIT_HIGH:
+			printf("(Timeout: INIT not high after deasserting PROGRAM*)\n ");
+			break;
+		case ERROR_FPGA_PRG_DONE:
+			printf("(Timeout: DONE not high after programming FPGA)\n ");
+			break;
+		}
+
+		/* display infos on fpgaimage */
+		index = 15;
+		for (i=0; i<4; i++) {
+			len = dst[index];
+			printf("FPGA: %s\n", &(dst[index+1]));
+			index += len+3;
+		}
+		putc ('\n');
+		/* delayed reboot */
+		for (i=20; i>0; i--) {
+			printf("Rebooting in %2d seconds \r",i);
+			for (index=0;index<1000;index++)
+				udelay(1000);
+		}
+		putc ('\n');
+		do_reset(NULL, 0, 0, NULL);
+	}
+
+	/* restore gpio/cs settings */
+	mtdcr(cntrl0, cntrl0Reg);
+
+	puts("FPGA:  ");
+
+	/* display infos on fpgaimage */
+	index = 15;
+	for (i=0; i<4; i++) {
+		len = dst[index];
+		printf("%s ", &(dst[index+1]));
+		index += len+3;
+	}
+	putc ('\n');
+
+	free(dst);
+
+	/*
+	 * Reset FPGA via FPGA_DATA pin
+	 */
+	SET_FPGA(FPGA_PRG | FPGA_CLK);
+	udelay(1000); /* wait 1ms */
+	SET_FPGA(FPGA_PRG | FPGA_CLK | FPGA_DATA);
+	udelay(1000); /* wait 1ms */
+
+	/*
+	 * Enable power on PS/2 interface
+	 */
+	*fpga_mode |= CFG_FPGA_CTRL_PS2_RESET;
+
+	/*
+	 * Enable interrupts in exar duart mcr[3]
+	 */
+	*duart0_mcr = 0x08;
+	*duart1_mcr = 0x08;
+#endif
+
+	return (0);
+}
+
+
+/*
+ * Check Board Identity:
+ */
+
+int checkboard (void)
+{
+	unsigned char str[64];
+	int i = getenv_r ("serial#", str, sizeof(str));
+
+	puts ("Board: ");
+
+	if (i == -1) {
+		puts ("### No HW ID - assuming ABG405");
+	} else {
+		puts(str);
+	}
+
+	putc ('\n');
+
+	return 0;
+}
+
+/* ------------------------------------------------------------------------- */
+
+long int initdram (int board_type)
+{
+	unsigned long val;
+
+	mtdcr(memcfga, mem_mb0cf);
+	val = mfdcr(memcfgd);
+
+#if 0
+	printf("\nmb0cf=%x\n", val); /* test-only */
+	printf("strap=%x\n", mfdcr(strap)); /* test-only */
+#endif
+
+	return (4*1024*1024 << ((val & 0x000e0000) >> 17));
+}
+
+/* ------------------------------------------------------------------------- */
+
+int testdram (void)
+{
+	/* TODO: XXX XXX XXX */
+	printf ("test: 16 MB - ok\n");
+
+	return (0);
+}
+
+/* ------------------------------------------------------------------------- */

board/esd/pmc405/strataflash.c

@@ -0,0 +1,796 @@
+/*
+ * (C) Copyright 2002
+ * Brad Kemp, Seranoa Networks, Brad.Kemp@seranoa.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/processor.h>
+
+#undef  DEBUG_FLASH 
+/*
+ * This file implements a Common Flash Interface (CFI) driver for ppcboot.
+ * The width of the port and the width of the chips are determined at initialization.
+ * These widths are used to calculate the address for access CFI data structures.
+ * It has been tested on an Intel Strataflash implementation.
+ *
+ * References
+ * JEDEC Standard JESD68 - Common Flash Interface (CFI)
+ * JEDEC Standard JEP137-A Common Flash Interface (CFI) ID Codes
+ * Intel Application Note 646 Common Flash Interface (CFI) and Command Sets
+ * Intel 290667-008 3 Volt Intel StrataFlash Memory datasheet
+ *
+ * TODO
+ * Use Primary Extended Query table (PRI) and Alternate Algorithm Query Table (ALT) to determine if protection is available
+ * Add support for other command sets Use the PRI and ALT to determine command set
+ * Verify erase and program timeouts.
+ */
+
+#define FLASH_CMD_CFI			0x98
+#define FLASH_CMD_READ_ID		0x90
+#define FLASH_CMD_RESET			0xff
+#define FLASH_CMD_BLOCK_ERASE		0x20
+#define FLASH_CMD_ERASE_CONFIRM		0xD0
+#define FLASH_CMD_WRITE			0x40
+#define FLASH_CMD_PROTECT		0x60
+#define FLASH_CMD_PROTECT_SET		0x01
+#define FLASH_CMD_PROTECT_CLEAR		0xD0
+#define FLASH_CMD_CLEAR_STATUS		0x50
+#define FLASH_CMD_WRITE_TO_BUFFER       0xE8
+#define FLASH_CMD_WRITE_BUFFER_CONFIRM  0xD0
+
+#define FLASH_STATUS_DONE		0x80
+#define FLASH_STATUS_ESS		0x40
+#define FLASH_STATUS_ECLBS		0x20
+#define FLASH_STATUS_PSLBS		0x10
+#define FLASH_STATUS_VPENS		0x08
+#define FLASH_STATUS_PSS		0x04
+#define FLASH_STATUS_DPS		0x02
+#define FLASH_STATUS_R			0x01
+#define FLASH_STATUS_PROTECT		0x01
+
+#define FLASH_OFFSET_CFI		0x55
+#define FLASH_OFFSET_CFI_RESP		0x10
+#define FLASH_OFFSET_WTOUT		0x1F
+#define FLASH_OFFSET_WBTOUT             0x20
+#define FLASH_OFFSET_ETOUT		0x21
+#define FLASH_OFFSET_CETOUT             0x22
+#define FLASH_OFFSET_WMAX_TOUT		0x23
+#define FLASH_OFFSET_WBMAX_TOUT         0x24
+#define FLASH_OFFSET_EMAX_TOUT		0x25
+#define FLASH_OFFSET_CEMAX_TOUT         0x26
+#define FLASH_OFFSET_SIZE		0x27
+#define FLASH_OFFSET_INTERFACE          0x28
+#define FLASH_OFFSET_BUFFER_SIZE        0x2A
+#define FLASH_OFFSET_NUM_ERASE_REGIONS	0x2C
+#define FLASH_OFFSET_ERASE_REGIONS	0x2D
+#define FLASH_OFFSET_PROTECT		0x02
+#define FLASH_OFFSET_USER_PROTECTION    0x85
+#define FLASH_OFFSET_INTEL_PROTECTION   0x81
+
+
+#define FLASH_MAN_CFI			0x01000000
+
+
+
+
+typedef union {
+	unsigned char c;
+	unsigned short w;
+	unsigned long l;
+} cfiword_t;
+
+typedef union {
+	unsigned char * cp;
+	unsigned short *wp;
+	unsigned long *lp;
+} cfiptr_t;
+
+#define NUM_ERASE_REGIONS 4
+
+flash_info_t	flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips	*/
+
+
+/*-----------------------------------------------------------------------
+ * Functions
+ */
+
+
+
+static void flash_add_byte(flash_info_t *info, cfiword_t * cword, uchar c);
+static void flash_make_cmd(flash_info_t * info, uchar cmd, void * cmdbuf);
+static void flash_write_cmd(flash_info_t * info, int sect, uchar offset, uchar cmd);
+static int flash_isequal(flash_info_t * info, int sect, uchar offset, uchar cmd);
+static int flash_isset(flash_info_t * info, int sect, uchar offset, uchar cmd);
+static int flash_detect_cfi(flash_info_t * info);
+static ulong flash_get_size (ulong base, int banknum);
+static int flash_write_cfiword (flash_info_t *info, ulong dest, cfiword_t cword);
+static int flash_full_status_check(flash_info_t * info, ulong sector, ulong tout, char * prompt);
+#ifdef CFG_FLASH_USE_BUFFER_WRITE
+static int flash_write_cfibuffer(flash_info_t * info, ulong dest, uchar * cp, int len);
+#endif
+/*-----------------------------------------------------------------------
+ * create an address based on the offset and the port width
+ */
+inline uchar * flash_make_addr(flash_info_t * info, int sect, int offset)
+{
+	return ((uchar *)(info->start[sect] + (offset * info->portwidth)));
+}
+/*-----------------------------------------------------------------------
+ * read a character at a port width address
+ */
+inline uchar flash_read_uchar(flash_info_t * info, uchar offset)
+{
+	uchar *cp;
+	cp = flash_make_addr(info, 0, offset);
+	return (cp[info->portwidth - 1]);
+}
+
+/*-----------------------------------------------------------------------
+ * read a short word by swapping for ppc format.
+ */
+ushort flash_read_ushort(flash_info_t * info, int sect,  uchar offset)
+{
+    uchar * addr;
+
+    addr = flash_make_addr(info, sect, offset);
+    return ((addr[(2*info->portwidth) - 1] << 8) | addr[info->portwidth - 1]);
+
+}
+
+/*-----------------------------------------------------------------------
+ * read a long word by picking the least significant byte of each maiximum
+ * port size word. Swap for ppc format.
+ */
+ulong flash_read_long(flash_info_t * info, int sect,  uchar offset)
+{
+    uchar * addr;
+
+    addr = flash_make_addr(info, sect, offset);
+    return ( (addr[(2*info->portwidth) - 1] << 24 ) | (addr[(info->portwidth) -1] << 16) |
+	    (addr[(4*info->portwidth) - 1] << 8) | addr[(3*info->portwidth) - 1]);
+
+}
+
+/*-----------------------------------------------------------------------
+ */
+unsigned long flash_init (void)
+{
+	unsigned long size;
+	int i;
+	unsigned long  address;
+
+
+	/* The flash is positioned back to back, with the demultiplexing of the chip
+	 * based on the A24 address line.
+	 *
+	 */
+
+	address = CFG_FLASH_BASE;
+	size = 0;
+
+	/* Init: no FLASHes known */
+	for (i=0; i<CFG_MAX_FLASH_BANKS; ++i) {
+		flash_info[i].flash_id = FLASH_UNKNOWN;
+		size += flash_info[i].size = flash_get_size(address, i);
+		address += CFG_FLASH_INCREMENT;
+		if (flash_info[0].flash_id == FLASH_UNKNOWN) {
+			printf ("## Unknown FLASH on Bank %d - Size = 0x%08lx = %ld MB\n",i,
+				flash_info[0].size, flash_info[i].size<<20);
+		}
+	}
+
+#if 0 /* test-only */
+	/* Monitor protection ON by default */
+#if (CFG_MONITOR_BASE >= CFG_FLASH_BASE)
+	for(i=0; flash_info[0].start[i] < CFG_MONITOR_BASE+CFG_MONITOR_LEN-1; i++)
+		(void)flash_real_protect(&flash_info[0], i, 1);
+#endif
+#else
+	/* monitor protection ON by default */
+	flash_protect (FLAG_PROTECT_SET,
+		       - CFG_MONITOR_LEN,
+		       - 1, &flash_info[1]);
+#endif
+
+	return (size);
+}
+
+/*-----------------------------------------------------------------------
+ */
+int flash_erase (flash_info_t *info, int s_first, int s_last)
+{
+	int rcode = 0;
+	int prot;
+	int sect;
+
+	if( info->flash_id != FLASH_MAN_CFI) {
+		printf ("Can't erase unknown flash type - aborted\n");
+		return 1;
+	}
+	if ((s_first < 0) || (s_first > s_last)) {
+		printf ("- no sectors to erase\n");
+		return 1;
+	}
+
+	prot = 0;
+	for (sect=s_first; sect<=s_last; ++sect) {
+		if (info->protect[sect]) {
+			prot++;
+		}
+	}
+	if (prot) {
+		printf ("- Warning: %d protected sectors will not be erased!\n",
+			prot);
+	} else {
+		printf ("\n");
+	}
+
+
+	for (sect = s_first; sect<=s_last; sect++) {
+		if (info->protect[sect] == 0) { /* not protected */
+			flash_write_cmd(info, sect, 0, FLASH_CMD_CLEAR_STATUS);
+			flash_write_cmd(info, sect, 0, FLASH_CMD_BLOCK_ERASE);
+			flash_write_cmd(info, sect, 0, FLASH_CMD_ERASE_CONFIRM);
+			
+			if(flash_full_status_check(info, sect, info->erase_blk_tout, "erase")) {
+				rcode = 1;
+			} else
+				printf(".");
+		}
+	}
+	printf (" done\n");
+	return rcode;
+}
+
+/*-----------------------------------------------------------------------
+ */
+void flash_print_info  (flash_info_t *info)
+{
+	int i;
+
+	if (info->flash_id != FLASH_MAN_CFI) {
+		printf ("missing or unknown FLASH type\n");
+		return;
+	}
+
+	printf("CFI conformant FLASH (%d x %d)",
+	       (info->portwidth	 << 3 ), (info->chipwidth  << 3 ));
+	printf ("  Size: %ld MB in %d Sectors\n",
+		info->size >> 20, info->sector_count);
+	printf(" Erase timeout %ld ms, write timeout %ld ms, buffer write timeout %ld ms, buffer size %d\n",
+	       info->erase_blk_tout, info->write_tout, info->buffer_write_tout, info->buffer_size);
+      
+	printf ("  Sector Start Addresses:");
+	for (i=0; i<info->sector_count; ++i) {
+#ifdef CFG_FLASH_EMPTY_INFO
+		int k;
+		int size;
+		int erased;
+		volatile unsigned long *flash;
+
+                /*
+                 * Check if whole sector is erased
+                 */
+                if (i != (info->sector_count-1))
+                  size = info->start[i+1] - info->start[i];
+                else
+                  size = info->start[0] + info->size - info->start[i];
+                erased = 1;
+                flash = (volatile unsigned long *)info->start[i];
+                size = size >> 2;        /* divide by 4 for longword access */
+                for (k=0; k<size; k++)
+                  {
+                    if (*flash++ != 0xffffffff)
+                      {
+                        erased = 0;
+                        break;
+                      }
+                  }
+
+		if ((i % 5) == 0)
+			printf ("\n   ");
+                /* print empty and read-only info */
+		printf (" %08lX%s%s",
+			info->start[i],
+			erased ? " E" : "  ",
+			info->protect[i] ? "RO " : "   ");
+#else
+		if ((i % 5) == 0)
+			printf ("\n   ");
+		printf (" %08lX%s",
+			info->start[i],
+			info->protect[i] ? " (RO)" : "     ");
+#endif
+	}
+	printf ("\n");
+	return;
+}
+
+/*-----------------------------------------------------------------------
+ * Copy memory to flash, returns:
+ * 0 - OK
+ * 1 - write timeout
+ * 2 - Flash not erased
+ */
+int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
+{
+	ulong wp;
+	ulong cp;
+	int aln;
+	cfiword_t cword;
+	int i, rc;
+
+	/* get lower aligned address */
+	wp = (addr & ~(info->portwidth - 1));
+
+	/* handle unaligned start */
+	if((aln = addr - wp) != 0) {
+		cword.l = 0;
+		cp = wp;
+		for(i=0;i<aln; ++i, ++cp)
+			flash_add_byte(info, &cword, (*(uchar *)cp));
+
+		for(; (i< info->portwidth) && (cnt > 0) ; i++) {
+			flash_add_byte(info, &cword, *src++);
+			cnt--;
+			cp++;
+		}
+		for(; (cnt == 0) && (i < info->portwidth); ++i, ++cp)
+			flash_add_byte(info, &cword, (*(uchar *)cp));
+		if((rc = flash_write_cfiword(info, wp, cword)) != 0)
+			return rc;
+		wp = cp;
+	}
+
+#ifdef CFG_FLASH_USE_BUFFER_WRITE
+	while(cnt >= info->portwidth) {
+		i = info->buffer_size > cnt? cnt: info->buffer_size;
+		if((rc = flash_write_cfibuffer(info, wp, src,i)) != ERR_OK)
+			return rc;
+		wp += i;
+		src += i;
+		cnt -=i;
+	}
+#else
+	/* handle the aligned part */
+	while(cnt >= info->portwidth) {
+		cword.l = 0;
+		for(i = 0; i < info->portwidth; i++) {
+			flash_add_byte(info, &cword, *src++);
+		}
+		if((rc = flash_write_cfiword(info, wp, cword)) != 0)
+			return rc;
+		wp += info->portwidth;
+		cnt -= info->portwidth;
+	}
+#endif /* CFG_FLASH_USE_BUFFER_WRITE */
+	if (cnt == 0) {
+		return (0);
+	}
+
+	/*
+	 * handle unaligned tail bytes
+	 */
+	cword.l = 0;
+	for (i=0, cp=wp; (i<info->portwidth) && (cnt>0); ++i, ++cp) {
+		flash_add_byte(info, &cword, *src++);
+		--cnt;
+	}
+	for (; i<info->portwidth; ++i, ++cp) {
+		flash_add_byte(info, & cword, (*(uchar *)cp));
+	}
+
+	return flash_write_cfiword(info, wp, cword);
+}
+
+/*-----------------------------------------------------------------------
+ */
+int flash_real_protect(flash_info_t *info, long sector, int prot)
+{
+	int retcode = 0;
+
+	flash_write_cmd(info, sector, 0, FLASH_CMD_CLEAR_STATUS);
+	flash_write_cmd(info, sector, 0, FLASH_CMD_PROTECT);
+	if(prot)
+		flash_write_cmd(info, sector, 0, FLASH_CMD_PROTECT_SET);
+	else
+		flash_write_cmd(info, sector, 0, FLASH_CMD_PROTECT_CLEAR);
+
+	if((retcode = flash_full_status_check(info, sector, info->erase_blk_tout, 
+					 prot?"protect":"unprotect")) == 0) {
+
+		info->protect[sector] = prot;
+		/* Intel's unprotect unprotects all locking */
+		if(prot == 0) {
+			int i;
+			for(i = 0 ; i<info->sector_count; i++) {
+				if(info->protect[i])
+					flash_real_protect(info, i, 1);
+			}
+		}
+	}
+
+	return retcode;
+}
+/*-----------------------------------------------------------------------
+ *  wait for XSR.7 to be set. Time out with an error if it does not.
+ *  This routine does not set the flash to read-array mode.
+ */
+static int flash_status_check(flash_info_t * info, ulong sector, ulong tout, char * prompt)
+{
+	ulong start;
+
+	/* Wait for command completion */
+	start = get_timer (0);
+	while(!flash_isset(info, sector, 0, FLASH_STATUS_DONE)) {
+		if (get_timer(start) > info->erase_blk_tout) {
+			printf("Flash %s timeout at address %lx\n", prompt, info->start[sector]);
+			flash_write_cmd(info, sector, 0, FLASH_CMD_RESET);
+			return ERR_TIMOUT;
+		}
+	}
+	return ERR_OK;
+}
+/*-----------------------------------------------------------------------
+ * Wait for XSR.7 to be set, if it times out print an error, otherwise do a full status check.
+ * This routine sets the flash to read-array mode.
+ */
+static int flash_full_status_check(flash_info_t * info, ulong sector, ulong tout, char * prompt)
+{
+	int retcode;
+	retcode = flash_status_check(info, sector, tout, prompt);
+	if((retcode == ERR_OK) && !flash_isequal(info,sector, 0, FLASH_STATUS_DONE)) {
+		retcode = ERR_INVAL;
+		printf("Flash %s error at address %lx\n", prompt,info->start[sector]);
+		if(flash_isset(info, sector, 0, FLASH_STATUS_ECLBS | FLASH_STATUS_PSLBS)){
+			printf("Command Sequence Error.\n");
+		} else if(flash_isset(info, sector, 0, FLASH_STATUS_ECLBS)){
+			printf("Block Erase Error.\n");
+		        retcode = ERR_NOT_ERASED;
+		} else if (flash_isset(info, sector, 0, FLASH_STATUS_PSLBS)) {
+			printf("Locking Error\n");
+		}
+		if(flash_isset(info, sector, 0, FLASH_STATUS_DPS)){
+			printf("Block locked.\n");
+			retcode = ERR_PROTECTED;
+		}
+		if(flash_isset(info, sector, 0, FLASH_STATUS_VPENS))
+			printf("Vpp Low Error.\n");
+	}
+	flash_write_cmd(info, sector, 0, FLASH_CMD_RESET);
+	return retcode;
+}
+/*-----------------------------------------------------------------------
+ */
+static void flash_add_byte(flash_info_t *info, cfiword_t * cword, uchar c)
+{
+	switch(info->portwidth) {
+	case FLASH_CFI_8BIT:
+		cword->c = c;
+		break;
+	case FLASH_CFI_16BIT:
+		cword->w = (cword->w << 8) | c;
+		break;
+	case FLASH_CFI_32BIT:
+		cword->l = (cword->l << 8) | c;
+	}
+}
+
+
+/*-----------------------------------------------------------------------
+ * make a proper sized command based on the port and chip widths
+ */
+static void flash_make_cmd(flash_info_t * info, uchar cmd, void * cmdbuf)
+{
+	int i;
+	uchar *cp = (uchar *)cmdbuf;
+	for(i=0; i< info->portwidth; i++)
+		*cp++ = ((i+1) % info->chipwidth) ? '\0':cmd;
+}
+
+/*
+ * Write a proper sized command to the correct address
+ */
+static void flash_write_cmd(flash_info_t * info, int sect, uchar offset, uchar cmd)
+{
+
+	volatile cfiptr_t addr;
+	cfiword_t cword;
+	addr.cp = flash_make_addr(info, sect, offset);
+	flash_make_cmd(info, cmd, &cword);
+	switch(info->portwidth) {
+	case FLASH_CFI_8BIT:
+		*addr.cp = cword.c;
+		break;
+	case FLASH_CFI_16BIT:
+		*addr.wp = cword.w;
+		break;
+	case FLASH_CFI_32BIT:
+		*addr.lp = cword.l;
+		break;
+	}
+}
+
+/*-----------------------------------------------------------------------
+ */
+static int flash_isequal(flash_info_t * info, int sect, uchar offset, uchar cmd)
+{
+	cfiptr_t cptr;
+	cfiword_t cword;
+	int retval;
+	cptr.cp = flash_make_addr(info, sect, offset);
+	flash_make_cmd(info, cmd, &cword);
+	switch(info->portwidth) {
+	case FLASH_CFI_8BIT:
+		retval = (cptr.cp[0] == cword.c);
+		break;
+	case FLASH_CFI_16BIT:
+		retval = (cptr.wp[0] == cword.w);
+		break;
+	case FLASH_CFI_32BIT:
+		retval = (cptr.lp[0] == cword.l);
+		break;
+	default:
+		retval = 0;
+		break;
+	}
+	return retval;
+}
+/*-----------------------------------------------------------------------
+ */
+static int flash_isset(flash_info_t * info, int sect, uchar offset, uchar cmd)
+{
+	cfiptr_t cptr;
+	cfiword_t cword;
+	int retval;
+	cptr.cp = flash_make_addr(info, sect, offset);
+	flash_make_cmd(info, cmd, &cword);
+	switch(info->portwidth) {
+	case FLASH_CFI_8BIT:
+		retval = ((cptr.cp[0] & cword.c) == cword.c);
+		break;
+	case FLASH_CFI_16BIT:
+		retval = ((cptr.wp[0] & cword.w) == cword.w);
+		break;
+	case FLASH_CFI_32BIT:
+		retval = ((cptr.lp[0] & cword.l) == cword.l);
+		break;
+	default:
+		retval = 0;
+		break;
+	}
+	return retval;
+}
+
+/*-----------------------------------------------------------------------
+ * detect if flash is compatible with the Common Flash Interface (CFI)
+ * http://www.jedec.org/download/search/jesd68.pdf
+ *
+*/
+static int flash_detect_cfi(flash_info_t * info)
+{
+
+	for(info->portwidth=FLASH_CFI_8BIT; info->portwidth <= FLASH_CFI_32BIT;
+	    info->portwidth <<= 1) {
+		for(info->chipwidth =FLASH_CFI_BY8;
+		    info->chipwidth <= info->portwidth;
+		    info->chipwidth <<= 1) {
+			flash_write_cmd(info, 0, 0, FLASH_CMD_RESET);
+			flash_write_cmd(info, 0, FLASH_OFFSET_CFI, FLASH_CMD_CFI);
+			if(flash_isequal(info, 0, FLASH_OFFSET_CFI_RESP,'Q') &&
+			   flash_isequal(info, 0, FLASH_OFFSET_CFI_RESP + 1, 'R') &&
+			   flash_isequal(info, 0, FLASH_OFFSET_CFI_RESP + 2, 'Y'))
+				return 1;
+		}
+	}
+	return 0;
+}
+/*
+ * The following code cannot be run from FLASH!
+ *
+ */
+static ulong flash_get_size (ulong base, int banknum)
+{
+	flash_info_t * info = &flash_info[banknum];
+	int i, j;
+	int sect_cnt;
+	unsigned long sector;
+	unsigned long tmp;
+	int size_ratio;
+	uchar num_erase_regions;
+	int  erase_region_size;
+	int  erase_region_count;
+
+	info->start[0] = base;
+
+	if(flash_detect_cfi(info)){
+#ifdef DEBUG_FLASH
+		printf("portwidth=%d chipwidth=%d\n", info->portwidth, info->chipwidth); /* test-only */
+#endif
+		size_ratio = info->portwidth / info->chipwidth;
+		num_erase_regions = flash_read_uchar(info, FLASH_OFFSET_NUM_ERASE_REGIONS);
+#ifdef DEBUG_FLASH
+		printf("found %d erase regions\n", num_erase_regions);
+#endif
+		sect_cnt = 0;
+		sector = base;
+		for(i = 0 ; i < num_erase_regions; i++) {
+			if(i > NUM_ERASE_REGIONS) {
+				printf("%d erase regions found, only %d used\n",
+				       num_erase_regions, NUM_ERASE_REGIONS);
+				break;
+			}
+			tmp = flash_read_long(info, 0, FLASH_OFFSET_ERASE_REGIONS);
+			erase_region_size = (tmp & 0xffff)? ((tmp & 0xffff) * 256): 128;
+			tmp >>= 16;
+			erase_region_count = (tmp & 0xffff) +1;
+			for(j = 0; j< erase_region_count; j++) {
+				info->start[sect_cnt] = sector;
+				sector += (erase_region_size * size_ratio);
+				info->protect[sect_cnt] = flash_isset(info, sect_cnt, FLASH_OFFSET_PROTECT, FLASH_STATUS_PROTECT);
+				sect_cnt++;
+			}
+		}
+
+		info->sector_count = sect_cnt;
+		/* multiply the size by the number of chips */
+		info->size = (1 << flash_read_uchar(info, FLASH_OFFSET_SIZE)) * size_ratio;
+		info->buffer_size = (1 << flash_read_ushort(info, 0, FLASH_OFFSET_BUFFER_SIZE));
+		tmp = 1 << flash_read_uchar(info, FLASH_OFFSET_ETOUT);
+		info->erase_blk_tout = (tmp * (1 << flash_read_uchar(info, FLASH_OFFSET_EMAX_TOUT)));
+		tmp = 1 << flash_read_uchar(info, FLASH_OFFSET_WBTOUT);
+		info->buffer_write_tout = (tmp * (1 << flash_read_uchar(info, FLASH_OFFSET_WBMAX_TOUT)));
+		tmp = 1 << flash_read_uchar(info, FLASH_OFFSET_WTOUT);
+		info->write_tout = (tmp * (1 << flash_read_uchar(info, FLASH_OFFSET_WMAX_TOUT)))/ 1000;
+		info->flash_id = FLASH_MAN_CFI;
+	}
+
+	flash_write_cmd(info, 0, 0, FLASH_CMD_RESET);
+	return(info->size);
+}
+
+
+/*-----------------------------------------------------------------------
+ */
+static int flash_write_cfiword (flash_info_t *info, ulong dest, cfiword_t cword)
+{
+
+	cfiptr_t ctladdr;
+	cfiptr_t cptr;
+	int flag;
+
+	ctladdr.cp = flash_make_addr(info, 0, 0);
+	cptr.cp = (uchar *)dest;
+
+
+	/* Check if Flash is (sufficiently) erased */
+	switch(info->portwidth) {
+	case FLASH_CFI_8BIT:
+		flag = ((cptr.cp[0] & cword.c) == cword.c);
+		break;
+	case FLASH_CFI_16BIT:
+		flag = ((cptr.wp[0] & cword.w) == cword.w);
+		break;
+	case FLASH_CFI_32BIT:
+		flag = ((cptr.lp[0] & cword.l)	== cword.l);
+		break;
+	default:
+		return 2;
+	}
+	if(!flag)
+		return 2;
+
+	/* Disable interrupts which might cause a timeout here */
+	flag = disable_interrupts();
+
+	flash_write_cmd(info, 0, 0, FLASH_CMD_CLEAR_STATUS);
+	flash_write_cmd(info, 0, 0, FLASH_CMD_WRITE);
+
+	switch(info->portwidth) {
+	case FLASH_CFI_8BIT:
+		cptr.cp[0] = cword.c;
+		break;
+	case FLASH_CFI_16BIT:
+		cptr.wp[0] = cword.w;
+		break;
+	case FLASH_CFI_32BIT:
+		cptr.lp[0] = cword.l;
+		break;
+	}
+
+	/* re-enable interrupts if necessary */
+	if(flag)
+		enable_interrupts();
+
+	return flash_full_status_check(info, 0, info->write_tout, "write");
+}
+
+#ifdef CFG_FLASH_USE_BUFFER_WRITE
+
+/* loop through the sectors from the highest address
+ * when the passed address is greater or equal to the sector address
+ * we have a match
+ */
+static int find_sector(flash_info_t *info, ulong addr)
+{
+	int sector;
+	for(sector = info->sector_count - 1; sector >= 0; sector--) {
+		if(addr >= info->start[sector]) 
+			break;
+	}
+	return sector;
+}
+
+static int flash_write_cfibuffer(flash_info_t * info, ulong dest, uchar * cp, int len)
+{
+	
+	int sector;
+	int cnt;
+	int retcode;
+	volatile cfiptr_t src;
+	volatile cfiptr_t dst;
+
+	src.cp = cp;
+	dst.cp = (uchar *)dest;
+	sector = find_sector(info, dest);
+	flash_write_cmd(info, sector, 0, FLASH_CMD_CLEAR_STATUS);
+	flash_write_cmd(info, sector, 0, FLASH_CMD_WRITE_TO_BUFFER);
+	if((retcode = flash_status_check(info, sector, info->buffer_write_tout,
+					 "write to buffer")) == ERR_OK) {
+		switch(info->portwidth) {
+		case FLASH_CFI_8BIT:
+			cnt = len;
+			break;
+		case FLASH_CFI_16BIT:
+			cnt = len >> 1;
+			break;
+		case FLASH_CFI_32BIT:
+			cnt = len >> 2;
+			break;
+		default:
+			return ERR_INVAL;
+			break;
+		}
+		flash_write_cmd(info, sector, 0, (uchar)cnt-1);
+		while(cnt-- > 0) {
+			switch(info->portwidth) {
+			case FLASH_CFI_8BIT:
+				*dst.cp++ = *src.cp++;
+				break;
+			case FLASH_CFI_16BIT:
+				*dst.wp++ = *src.wp++;
+				break;
+			case FLASH_CFI_32BIT:
+				*dst.lp++ = *src.lp++;
+				break;
+			default:
+				return ERR_INVAL;
+				break;
+			}
+		}
+		flash_write_cmd(info, sector, 0, FLASH_CMD_WRITE_BUFFER_CONFIRM);
+		retcode = flash_full_status_check(info, sector, info->buffer_write_tout,
+					     "buffer write");
+	} 
+	flash_write_cmd(info, sector, 0, FLASH_CMD_CLEAR_STATUS);
+	return retcode;
+}	
+#endif /* CFG_USE_FLASH_BUFFER_WRITE */

board/esd/pmc405/u-boot.lds

@@ -0,0 +1,142 @@
+/*
+ * (C) Copyright 2000, 2001
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+/* Do we need any of these for elf?
+   __DYNAMIC = 0;    */
+SECTIONS
+{
+  .resetvec 0xFFFFFFFC :
+  {
+    *(.resetvec)
+  } = 0xffff
+
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)		}
+  .rela.text     : { *(.rela.text) 	}
+  .rel.data      : { *(.rel.data)		}
+  .rela.data     : { *(.rela.data) 	}
+  .rel.rodata    : { *(.rel.rodata) 	}
+  .rela.rodata   : { *(.rela.rodata) 	}
+  .rel.got       : { *(.rel.got)		}
+  .rela.got      : { *(.rela.got)		}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)		}
+  .rela.bss      : { *(.rela.bss)		}
+  .rel.plt       : { *(.rel.plt)		}
+  .rela.plt      : { *(.rela.plt)		}
+  .init          : { *(.init)	}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    /* WARNING - the following is hand-optimized to fit within	*/
+    /* the sector layout of our flash chips!	XXX FIXME XXX	*/
+
+    cpu/ppc4xx/start.o	(.text)
+    cpu/ppc4xx/traps.o	(.text)
+    cpu/ppc4xx/interrupts.o	(.text)
+    cpu/ppc4xx/serial.o	(.text)
+    cpu/ppc4xx/cpu_init.o	(.text)
+    cpu/ppc4xx/speed.o	(.text)
+    cpu/ppc4xx/405gp_enet.o	(.text)
+    common/dlmalloc.o	(.text)
+    lib_generic/crc32.o		(.text)
+    lib_ppc/extable.o	(.text)
+    lib_generic/zlib.o		(.text)
+
+/*    . = env_offset;*/
+/*    common/environment.o(.text)*/
+
+    *(.text)
+    *(.fixup)
+    *(.got1)
+  }
+  _etext = .;
+  PROVIDE (etext = .);
+  .rodata    :
+  {
+    *(.rodata)
+    *(.rodata1)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x00FF) & 0xFFFFFF00;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
+  __fixup_entries = (. - _FIXUP_TABLE_)>>2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(256);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(256);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+  _end = . ;
+  PROVIDE (end = .);
+}

board/esteem192e/flash.c

@@ -104,7 +104,7 @@ unsigned long flash_init (void)
 	/* monitor protection ON by default */
 	(void)flash_protect(FLAG_PROTECT_SET,
 			    CFG_MONITOR_BASE,
-			    CFG_MONITOR_BASE+CFG_MONITOR_LEN-1,
+			    CFG_MONITOR_BASE+monitor_flash_len-1,
 			    &flash_info[0]);
 #endif
 
@@ -124,7 +124,7 @@ unsigned long flash_init (void)
 		/* monitor protection ON by default */
 		(void)flash_protect(FLAG_PROTECT_SET,
 				    CFG_MONITOR_BASE,
-				    CFG_MONITOR_BASE+CFG_MONITOR_LEN-1,
+				    CFG_MONITOR_BASE+monitor_flash_len-1,
 				    &flash_info[1]);
 #endif
 	} else {

board/etx094/flash.c

@@ -91,7 +91,7 @@ unsigned long flash_init (void)
 	/* monitor protection ON by default */
 	flash_protect(FLAG_PROTECT_SET,
 		      CFG_MONITOR_BASE,
-		      CFG_MONITOR_BASE+CFG_MONITOR_LEN-1,
+		      CFG_MONITOR_BASE+monitor_flash_len-1,
 		      &flash_info[0]);
 #endif
 
@@ -115,7 +115,7 @@ unsigned long flash_init (void)
 		/* monitor protection ON by default */
 		flash_protect(FLAG_PROTECT_SET,
 			      CFG_MONITOR_BASE,
-			      CFG_MONITOR_BASE+CFG_MONITOR_LEN-1,
+			      CFG_MONITOR_BASE+monitor_flash_len-1,
 			      &flash_info[1]);
 #endif
 	} else {

board/fads/flash.c

@@ -112,7 +112,7 @@ unsigned long flash_init (void)
 		/* monitor protection ON by default */
 		flash_protect(FLAG_PROTECT_SET,
 			      CFG_MONITOR_BASE,
-			      CFG_MONITOR_BASE+CFG_MONITOR_LEN-1,
+			      CFG_MONITOR_BASE+monitor_flash_len-1,
 			      &flash_info[i]);
 #endif
 

board/flagadm/flash.c

@@ -77,7 +77,7 @@ unsigned long flash_init (void)
 	/* monitor protection ON by default */
 	flash_protect(FLAG_PROTECT_SET,
 		      CFG_MONITOR_BASE,
-		      CFG_MONITOR_BASE+CFG_MONITOR_LEN-1,
+		      CFG_MONITOR_BASE+monitor_flash_len-1,
 		      &flash_info[0]);
 #endif
 

board/gen860t/flash.c

@@ -157,7 +157,7 @@ flash_init (void)
 	 */
 	flash_protect(FLAG_PROTECT_SET,
 		      	  CFG_MONITOR_BASE,
-		      	  CFG_MONITOR_BASE + CFG_MONITOR_LEN - 1,
+		      	  CFG_MONITOR_BASE + monitor_flash_len - 1,
 		      	  &flash_info[0]);
 #endif
 

board/genietv/flash.c

@@ -55,7 +55,7 @@ unsigned long flash_init (void)
 	/* Monitor protection ON by default */
 	flash_protect(FLAG_PROTECT_SET,
 		      CFG_MONITOR_BASE,
-		      CFG_MONITOR_BASE+CFG_MONITOR_LEN-1,
+		      CFG_MONITOR_BASE+monitor_flash_len-1,
 		      &flash_info[0]);
 #endif
 

board/gth/flash.c

@@ -102,7 +102,7 @@ unsigned long flash_init (void)
 	  /* monitor protection ON by default */
 	  (void)flash_protect(FLAG_PROTECT_SET,
 			    CFG_MONITOR_BASE,
-			    CFG_MONITOR_BASE+CFG_MONITOR_LEN-1,
+			    CFG_MONITOR_BASE+monitor_flash_len-1,
 			    &flash_info[0]);
 #endif
 
@@ -121,7 +121,7 @@ unsigned long flash_init (void)
 		/* monitor protection ON by default */
 		(void)flash_protect(FLAG_PROTECT_SET,
 				    CFG_MONITOR_BASE,
-				    CFG_MONITOR_BASE+CFG_MONITOR_LEN-1,
+				    CFG_MONITOR_BASE+monitor_flash_len-1,
 				    &flash_info[1]);
 #endif
 	}

board/gw8260/flash.c

@@ -96,7 +96,7 @@ unsigned long flash_init (void)
 #if CFG_MONITOR_BASE >= CFG_FLASH0_BASE
     flash_protect(FLAG_PROTECT_SET,
 		  CFG_MONITOR_BASE,
-		  CFG_MONITOR_BASE+CFG_MONITOR_LEN-1,
+		  CFG_MONITOR_BASE+monitor_flash_len-1,
 		  &flash_info[0]);
 #endif
 

board/hermes/flash.c

@@ -71,7 +71,7 @@ unsigned long flash_init (void)
 	/* monitor protection ON by default */
 	flash_protect(FLAG_PROTECT_SET,
 		      CFG_MONITOR_BASE,
-		      CFG_MONITOR_BASE+CFG_MONITOR_LEN-1,
+		      CFG_MONITOR_BASE+monitor_flash_len-1,
 		      &flash_info[0]);
 #endif
 

board/hymod/flash.c

@@ -321,7 +321,7 @@ flash_init(void)
 #if CFG_MONITOR_BASE == CFG_FLASH_BASE
 	(void)flash_protect(FLAG_PROTECT_SET,
 		      CFG_MONITOR_BASE,
-		      CFG_MONITOR_BASE+CFG_MONITOR_LEN-1,
+		      CFG_MONITOR_BASE+monitor_flash_len-1,
 		      &flash_info[0]);
 #endif
 

board/icu862/flash.c

@@ -104,7 +104,7 @@ unsigned long flash_init (void)
 	/* monitor protection ON by default */
 	flash_protect(FLAG_PROTECT_SET,
 		      CFG_MONITOR_BASE,
-		      CFG_MONITOR_BASE+CFG_MONITOR_LEN-1,
+		      CFG_MONITOR_BASE+monitor_flash_len-1,
 		      &flash_info[0]);
 #endif
 

board/impa7/flash.c

@@ -72,7 +72,7 @@ ulong flash_init(void)
      */
     flash_protect(FLAG_PROTECT_SET,
 		  CFG_FLASH_BASE,
-		  CFG_FLASH_BASE + _armboot_end_data - _armboot_start,
+		  CFG_FLASH_BASE + monitor_flash_len - 1,
 		  &flash_info[0]);
 
     flash_protect(FLAG_PROTECT_SET,

board/incaip/flash.c

@@ -100,7 +100,7 @@ unsigned long flash_init (void)
 	/* monitor protection ON by default */
 	flash_protect(FLAG_PROTECT_SET,
 		      CFG_MONITOR_BASE,
-		      CFG_MONITOR_BASE+CFG_MONITOR_LEN-1,
+		      CFG_MONITOR_BASE+monitor_flash_len-1,
 		      flash_get_info(CFG_MONITOR_BASE));
 #endif
 

board/innokom/u-boot.lds

@@ -31,7 +31,7 @@ SECTIONS
         . = ALIGN(4);
 	.text      :
 	{
-	  cpu/xscale/start.o	(.text)
+	  cpu/pxa/start.o	(.text)
 	  *(.text)
 	}
 

board/ip860/flash.c

@@ -90,7 +90,7 @@ unsigned long flash_init (void)
 	/* monitor protection ON by default */
 	flash_protect(FLAG_PROTECT_SET,
 		      CFG_MONITOR_BASE,
-		      CFG_MONITOR_BASE+CFG_MONITOR_LEN-1,
+		      CFG_MONITOR_BASE+monitor_flash_len-1,
 		      &flash_info[0]);
 #endif
 

board/iphase4539/flash.c

@@ -71,7 +71,7 @@ unsigned long flash_init (void)
 		/* monitor protection ON by default */
 		flash_protect(FLAG_PROTECT_SET,
 			      CFG_MONITOR_BASE,
-			      CFG_MONITOR_BASE + CFG_MONITOR_LEN - 1,
+			      CFG_MONITOR_BASE + monitor_flash_len - 1,
 			      flash_info + bank);
 #endif
 

board/ivm/flash.c

@@ -87,7 +87,7 @@ unsigned long flash_init (void)
 	/* monitor protection ON by default */
 	flash_protect(FLAG_PROTECT_SET,
 		      CFG_MONITOR_BASE,
-		      CFG_MONITOR_BASE+CFG_MONITOR_LEN-1,
+		      CFG_MONITOR_BASE+monitor_flash_len-1,
 		      &flash_info[0]);
 #endif
 

board/kup4k/flash.c

@@ -74,7 +74,7 @@ unsigned long flash_init (void)
 	/* monitor protection ON by default */
 	flash_protect(FLAG_PROTECT_SET,
 		      CFG_MONITOR_BASE,
-		      CFG_MONITOR_BASE+CFG_MONITOR_LEN-1,
+		      CFG_MONITOR_BASE+monitor_flash_len-1,
 		      &flash_info[0]);
 #endif
 

board/lantec/flash.c

@@ -134,7 +134,7 @@ unsigned long flash_init (void)
 	/* monitor protection ON by default */
 	flash_protect(FLAG_PROTECT_SET,
 		      CFG_MONITOR_BASE,
-		      CFG_MONITOR_BASE+CFG_MONITOR_LEN-1,
+		      CFG_MONITOR_BASE+monitor_flash_len-1,
 		      &flash_info[0]);
 #endif
 
@@ -166,7 +166,7 @@ unsigned long flash_init (void)
 		/* monitor protection ON by default */
 		flash_protect(FLAG_PROTECT_SET,
 			      CFG_MONITOR_BASE,
-			      CFG_MONITOR_BASE+CFG_MONITOR_LEN-1,
+			      CFG_MONITOR_BASE+monitor_flash_len-1,
 			      &flash_info[1]);
 #endif
 

board/lart/flash.c

@@ -105,7 +105,7 @@ ulong flash_init(void)
      */
     flash_protect(FLAG_PROTECT_SET,
 		  CFG_FLASH_BASE,
-		  CFG_FLASH_BASE + _armboot_end_data - _armboot_start,
+		  CFG_FLASH_BASE + monitor_flash_len - 1,
 		  &flash_info[0]);
 
     flash_protect(FLAG_PROTECT_SET,

board/lubbock/flash.c

@@ -86,7 +86,7 @@ unsigned long flash_init (void)
 	 */
 	flash_protect ( FLAG_PROTECT_SET,
 			CFG_FLASH_BASE,
-			CFG_FLASH_BASE + _armboot_end_data - _armboot_start,
+			CFG_FLASH_BASE + monitor_flash_len - 1,
 			&flash_info[0] );
 
 	flash_protect ( FLAG_PROTECT_SET,

board/lubbock/u-boot.lds

@@ -31,7 +31,7 @@ SECTIONS
         . = ALIGN(4);
 	.text      :
 	{
-	  cpu/xscale/start.o	(.text)
+	  cpu/pxa/start.o	(.text)
 	  *(.text)
 	}
 

board/lwmon/flash.c

@@ -123,7 +123,7 @@ unsigned long flash_init (void)
 	/* monitor protection ON by default */
 	flash_protect(FLAG_PROTECT_SET,
 		      CFG_MONITOR_BASE,
-		      CFG_MONITOR_BASE+CFG_MONITOR_LEN-1,
+		      CFG_MONITOR_BASE+monitor_flash_len-1,
 		      &flash_info[0]);
 #endif
 
@@ -156,7 +156,7 @@ unsigned long flash_init (void)
 		/* monitor protection ON by default */
 		flash_protect(FLAG_PROTECT_SET,
 			      CFG_MONITOR_BASE,
-			      CFG_MONITOR_BASE+CFG_MONITOR_LEN-1,
+			      CFG_MONITOR_BASE+monitor_flash_len-1,
 			      &flash_info[1]);
 #endif
 

board/mbx8xx/flash.c

@@ -79,7 +79,7 @@ unsigned long flash_init (void)
     /* monitor protection ON by default */
     flash_protect(FLAG_PROTECT_SET,
 		  CFG_MONITOR_BASE,
-		  CFG_MONITOR_BASE+CFG_MONITOR_LEN-1,
+		  CFG_MONITOR_BASE+monitor_flash_len-1,
 		  &flash_info[0]);
 #endif
 

board/mpc8260ads/flash.c

@@ -100,7 +100,7 @@ unsigned long flash_init (void)
 	/* monitor protection ON by default */
 	flash_protect(FLAG_PROTECT_SET,
 		      CFG_MONITOR_BASE,
-		      CFG_MONITOR_BASE+CFG_MONITOR_LEN-1,
+		      CFG_MONITOR_BASE+monitor_flash_len-1,
 		      &flash_info[0]);
 #endif
 

board/mpc8266ads/flash.c

@@ -101,7 +101,7 @@ unsigned long flash_init (void)
 	/* monitor protection ON by default */
 	flash_protect(FLAG_PROTECT_SET,
 		      CFG_MONITOR_BASE,
-		      CFG_MONITOR_BASE+CFG_MONITOR_LEN-1,
+		      CFG_MONITOR_BASE+monitor_flash_len-1,
 		      &flash_info[0]);
 #endif
 

board/mpc8266ads/mpc8266ads.c

@@ -489,10 +489,13 @@ long int initdram(int board_type)
      * The appropriate BRx/ORx registers have already been set when we
      * get here. The SDRAM can be accessed at the address CFG_SDRAM_BASE.
      */
-#if 1
+
     memctl->memc_mptpr = CFG_MPTPR;
     memctl->memc_psrt  = psrt;
 
+    memctl->memc_br2 = CFG_BR2_PRELIM;
+    memctl->memc_or2 = or;
+    
     memctl->memc_psdmr = psdmr | PSDMR_OP_PREA;
     *ramaddr = c;
 
@@ -530,41 +533,7 @@ long int initdram(int board_type)
 		memctl->memc_psdmr = psdmr | PSDMR_OP_NORM | PSDMR_RFEN;
 		*ramaddr = c;
     }
-#endif
-	/*
-    printf("memctl->memc_mptpr = 0x%08x\n", CFG_MPTPR);
-    printf("memctl->memc_psrt  = 0x%08x\n", psrt);
 
-    printf("memctl->memc_psdmr = 0x%08x\n", psdmr | PSDMR_OP_PREA);
-    printf("ramaddr = 0x%08x\n", ramaddr);
-
-    printf("memctl->memc_psdmr = 0x%08x\n", psdmr | PSDMR_OP_CBRR);
-
-    printf("memctl->memc_psdmr = 0x%08x\n", psdmr | PSDMR_OP_MRW);
-
-    printf("memctl->memc_psdmr = 0x%08x\n", psdmr | PSDMR_OP_NORM | PSDMR_RFEN);
-
-    immap->im_siu_conf.sc_ppc_acr   = 0x00000002;
-    immap->im_siu_conf.sc_ppc_alrh  = 0x01267893;
-    immap->im_siu_conf.sc_tescr1    = 0x00004000;
-	*/
-#if 0
-    /* init sdram dimm */
-    ramaddr                         = (uchar *)CFG_SDRAM_BASE;
-    memctl->memc_psrt               = 0x00000010;
-    immap->im_memctl.memc_or2       = 0xFF000CA0;
-    immap->im_memctl.memc_br2       = 0x00000041;
-    memctl->memc_psdmr              = 0x296EB452;
-    *ramaddr                        = c;
-    memctl->memc_psdmr              = 0x096EB452;
-    for (i = 0; i < 8; i++)
-        *ramaddr                    = c;
-
-    memctl->memc_psdmr              = 0x196EB452;
-    *ramaddr                        = c;
-    memctl->memc_psdmr              = 0x416EB452;
-    *ramaddr                        = c;
-#endif	
 	/* print info */
 	printf("SDRAM configuration read from SPD\n");
 	printf("\tSize per side = %dMB\n", sdram_size >> 20);
@@ -576,6 +545,7 @@ long int initdram(int board_type)
 	/*return (16 * 1024 * 1024);*/
 }
 
+
 #ifdef	CONFIG_PCI
 struct pci_controller hose;
 

board/mpl/common/common_util.c

@@ -32,6 +32,15 @@
 #include <devices.h>
 #include <pci.h>
 
+#ifdef CONFIG_PIP405
+#include "../pip405/pip405.h"
+#include <405gp_pci.h>
+#endif
+#ifdef CONFIG_MIP405
+#include "../mip405/mip405.h"
+#include <405gp_pci.h>
+#endif
+
 extern int  gunzip (void *, int, unsigned char *, int *);
 extern int mem_test(unsigned long start, unsigned long ramsize, int quiet);
 
@@ -363,12 +372,16 @@ void show_stdio_dev(void)
 #if defined(CONFIG_PIP405) || defined(CONFIG_MIP405)
 int switch_cs(unsigned char boot)
 {
-  	unsigned long pbcr;
-	mtdcr(ebccfga, pb0cr); /* get cs0 config reg */
-	pbcr = mfdcr(ebccfgd);
-	if((pbcr&0x00002000)==0) {
+	unsigned long pbcr;
+	int mode;
+
+	mode=get_boot_mode();
+	mtdcr(ebccfga, pb0cr);
+	pbcr = mfdcr (ebccfgd);
+	if (mode & BOOT_MPS) {
+		/* Boot width = 8 bit MPS Boot, set up MPS on CS0 */
 		/* we need only to switch if boot from MPS */
-		/*printf(" MPS boot mode detected. ");*/
+		/* printf(" MPS boot mode detected. ");*/
 		/* printf("cs0 cfg: %lx\n",pbcr); */
 		if(boot) {
 			/* switch to boot configuration */
@@ -388,8 +401,7 @@ int switch_cs(unsigned char boot)
 			mtdcr(ebccfgd, pbcr);
 			SW_CS_PRINTF("  new cs1 cfg: %lx, MPS is on High Address\n",pbcr);
 		}
-		else
-		{
+		else {
 			/* map flash to boot area, */
 			SW_CS_PRINTF("map Flash to boot area\n");
 			pbcr&=0x000FFFFF; /*mask base address of the cs0 */
@@ -412,7 +424,63 @@ int switch_cs(unsigned char boot)
 		SW_CS_PRINTF("Normal boot, no switching necessary\n");
 		return 0;
 	}
+
 }
+
+int get_boot_mode(void)
+{
+	unsigned long pbcr;
+	int res = 0;
+	pbcr = mfdcr (strap);
+	if ((pbcr & PSR_ROM_WIDTH_MASK) == 0) 
+		/* boot via MPS or MPS mapping */
+		res = BOOT_MPS;
+	if(pbcr & PSR_ROM_LOC) 
+		/* boot via PCI.. */
+		res |= BOOT_PCI;
+	 return res;
+}
+
+/* Setup cs0 parameter finally.
+   Map the flash high (in boot area)
+   This code can only be executed from SDRAM (after relocation).
+*/
+void setup_cs_reloc(void)
+{
+	unsigned long pbcr;
+	/* Since we are relocated, we can set-up the CS finaly
+	 * but first of all, switch off PCI mapping (in case it was a PCI boot) */
+	out32r(PMM0MA,0L);
+	icache_enable (); /* we are relocated */
+	/* for PCI Boot, we have to set-up the remaining CS correctly */
+	pbcr = mfdcr (strap);
+	if(pbcr & PSR_ROM_LOC) {
+		/* boot via PCI.. */
+		if ((pbcr & PSR_ROM_WIDTH_MASK) == 0) {
+		/* Boot width = 8 bit MPS Boot, set up MPS on CS0 */
+			#ifdef DEBUG
+			printf("Mapping MPS to CS0 @ 0x%lx\n",(MPS_CR_B & 0xfff00000));
+			#endif
+			mtdcr (ebccfga, pb0ap);
+			mtdcr (ebccfgd, MPS_AP);
+			mtdcr (ebccfga, pb0cr);
+			mtdcr (ebccfgd, MPS_CR_B);
+		}
+		else {
+			/* Flash boot, set up the Flash on CS0 */
+			#ifdef DEBUG
+			printf("Mapping Flash to CS0 @ 0x%lx\n",(FLASH_CR_B & 0xfff00000));
+			#endif
+			mtdcr (ebccfga, pb0ap);
+			mtdcr (ebccfgd, FLASH_AP);
+			mtdcr (ebccfga, pb0cr);
+			mtdcr (ebccfgd, FLASH_CR_B);
+		}
+	}
+	switch_cs(0); /* map Flash High */
+}
+
+
 #elif defined(CONFIG_VCMA9)
 int switch_cs(unsigned char boot)
 {
@@ -425,13 +493,11 @@ int do_mplcommon(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
  	ulong size,src,ld_addr;
 	int result;
 	backup_t back;
-	char sw;
 	src = MULTI_PURPOSE_SOCKET_ADDR;
 	size = IMAGE_SIZE;
 
 	if (strcmp(argv[1], "flash") == 0)
 	{
-		sw = switch_cs(0); /* Switch flash to normal location */
 #if (CONFIG_COMMANDS & CFG_CMD_FDC)
 		if (strcmp(argv[2], "floppy") == 0) {
  			char *local_args[3];
@@ -450,7 +516,6 @@ int do_mplcommon(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 				result=do_fdcboot(cmdtp, 0, 1, local_args);
 			}
 			result=mpl_prg_image(ld_addr);
-			switch_cs(sw); /* Switch flash back */
 			return result;
 		}
 #endif /* (CONFIG_COMMANDS & CFG_CMD_FDC) */
@@ -463,17 +528,13 @@ int do_mplcommon(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 			}
 			printf ("\nupdating bootloader image from memory at %lX\n",ld_addr);
 			result=mpl_prg_image(ld_addr);
-			switch_cs(sw); /* Switch flash back */
 			return result;
 		}
 		if (strcmp(argv[2], "mps") == 0) {
-			printf ("\nupdating bootloader image from MSP\n");
+			printf ("\nupdating bootloader image from MPS\n");
 			result=mpl_prg(src,size);
-			switch_cs(sw); /* Switch flash back */
 			return result;
 		}
-		switch_cs(sw); /* Switch flash back */
-
 	}
 	if (strcmp(argv[1], "mem") == 0)
 	{
@@ -551,11 +612,12 @@ void video_get_info_str (int line_number, char *info)
 	DECLARE_GLOBAL_DATA_PTR;
 	PPC405_SYS_INFO sys_info;
 	char rev;
-	int i;
+	int i,boot;
 	unsigned long pvr;
 	char buf[64];
 	char tmp[16];
-	unsigned char *s, *e, bc, sw;
+	char cpustr[16];
+	unsigned char *s, *e, bc;
 	switch (line_number)
 	{
 	case 2:
@@ -567,8 +629,13 @@ void video_get_info_str (int line_number, char *info)
 			case PVR_405GP_RC: rev='C'; break;
 			case PVR_405GP_RD: rev='D'; break;
 			case PVR_405GP_RE: rev='E'; break;
+			case PVR_405GPR_RB: rev='B'; break;
 			default:           rev='?'; break;
 		}
+		if(pvr==PVR_405GPR_RB)
+			sprintf(cpustr,"PPC405GPr %c",rev);
+		else
+			sprintf(cpustr,"PPC405GP %c",rev);
 		/* Board info */
 		i=0;
 		s=getenv ("serial#");
@@ -601,22 +668,21 @@ void video_get_info_str (int line_number, char *info)
 			}
 			buf[i++]=0;
 		}
-		sprintf (info," %s PPC405GP %c %s MHz (%lu/%lu/%lu MHz)",
-			buf,rev,
+		sprintf (info," %s %s %s MHz (%lu/%lu/%lu MHz)",
+			buf, cpustr,
 			strmhz (tmp, gd->cpu_clk), sys_info.freqPLB / 1000000,
 			sys_info.freqPLB / sys_info.pllOpbDiv / 1000000,
 			sys_info.freqPLB / sys_info.pllExtBusDiv / 1000000);
 		return;
 	case 3:
 		/* Memory Info */
-		sw = switch_cs (0);
-		switch_cs (sw);
+		boot = get_boot_mode();
 		bc = in8 (CONFIG_PORT_ADDR);
 		sprintf(info, " %luMB RAM, %luMB Flash Cfg 0x%02X %s %s",
 			gd->bd->bi_memsize / 0x100000,
 			gd->bd->bi_flashsize / 0x100000,
 			bc,
-			sw ? "MPS boot" : "Flash boot",
+			(boot & BOOT_MPS) ? "MPS boot" : "Flash boot",
 			ctfb.modeIdent);
 		return;
 	case 1:

board/mpl/common/common_util.h

@@ -27,11 +27,18 @@
 typedef struct {
 	char signature[4];
 	char serial_name[17]; 	/* "MIP405_1000xxxxx" */
-	char eth_addr[21];			/* "00:60:C2:0a:00:00" */
+	char eth_addr[21];	/* "00:60:C2:0a:00:00" */
 } backup_t;
 
 void get_backup_values(backup_t *buf);
 int switch_cs(unsigned char boot);
+#if defined(CONFIG_PIP405) || defined(CONFIG_MIP405)
+int get_boot_mode(void);
+void setup_cs_reloc(void);
+#define BOOT_MPS	0x01
+#define BOOT_PCI	0x02
+#endif
+
 void show_stdio_dev(void);
 void check_env(void);
 #if (CONFIG_COMMANDS & CFG_CMD_DOC)

board/mpl/common/flash.c

@@ -30,7 +30,7 @@
 
 /*
  * Modified 3/7/2001
- * - adopted for pip405, Denis Peter, MPL AG Switzerland
+ * - adapted for pip405, Denis Peter, MPL AG Switzerland
  * TODO:
  * clean-up
  */
@@ -38,12 +38,6 @@
 #include <common.h>
 #include <ppc4xx.h>
 #include <asm/processor.h>
-#ifdef CONFIG_PIP405
-#include "../pip405/pip405.h"
-#endif
-#ifdef CONFIG_MIP405
-#include "../mip405/mip405.h"
-#endif
 #include "common_util.h"
 
 flash_info_t	flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips	*/
@@ -52,23 +46,10 @@ flash_info_t	flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips	*/
  */
 static ulong flash_get_size (vu_long *addr, flash_info_t *info);
 static int write_word (flash_info_t *info, ulong dest, ulong data);
-static void flash_get_offsets (ulong base, flash_info_t *info);
 
 void unlock_intel_sectors(flash_info_t *info,ulong addr,ulong cnt);
 
 
-#ifdef CONFIG_ADCIOP
-#define ADDR0           0x0aa9
-#define ADDR1           0x0556
-#define FLASH_WORD_SIZE unsigned char
-#endif
-
-#ifdef CONFIG_CPCI405
-#define ADDR0           0x5555
-#define ADDR1           0x2aaa
-#define FLASH_WORD_SIZE unsigned short
-#endif
-
 #ifdef CONFIG_PIP405
 #define ADDR0           0x5555
 #define ADDR1           0x2aaa
@@ -92,16 +73,17 @@ unsigned long flash_init (void)
 {
 	unsigned long size_b0, size_b1;
 	int i;
-  unsigned long pbcr;
-  unsigned long base_b0, base_b1;
-  unsigned char rc;
 
-  rc=switch_cs(FALSE); /* map Flash High */
-
-	if(rc)
-		printf("(MPS Boot) ");
+	/* Since we are relocated, we can set-up the CS finally */
+	setup_cs_reloc();
+	/* get and display boot mode */
+	i=get_boot_mode();
+	if(i & BOOT_PCI)
+		printf("(PCI Boot %s Map) ",(i & BOOT_MPS) ?
+			"MPS" : "Flash");
 	else
-		printf("(Flash Boot) ");
+		printf("(%s Boot) ",(i & BOOT_MPS) ?
+			"MPS" : "Flash");
 	/* Init: no FLASHes known */
 	for (i=0; i<CFG_MAX_FLASH_BANKS; ++i) {
 		flash_info[i].flash_id = FLASH_UNKNOWN;
@@ -115,140 +97,39 @@ unsigned long flash_init (void)
 		printf ("## Unknown FLASH on Bank 0 - Size = 0x%08lx = %ld MB\n",
 			size_b0, size_b0<<20);
 	}
-	/* Only one bank */
-	if (CFG_MAX_FLASH_BANKS == 1)
-	  {
-	    /* Setup offsets */
-			/*  flash_get_offsets (FLASH_BASE0_PRELIM, &flash_info[0]); */
-	    /* Monitor protection ON by default */
+	/* protect the bootloader */
+	/* Monitor protection ON by default */
 #if CFG_MONITOR_BASE >= CFG_FLASH_BASE
-	 	    flash_protect(FLAG_PROTECT_SET,
-				CFG_MONITOR_BASE,
-				CFG_MONITOR_BASE+CFG_MONITOR_LEN-1,
-				&flash_info[0]);
+	flash_protect(FLAG_PROTECT_SET,
+			CFG_MONITOR_BASE,
+			CFG_MONITOR_BASE+monitor_flash_len-1,
+			&flash_info[0]);
 #endif
-	    size_b1 = 0 ;
-	    flash_info[0].size = size_b0;
-	  }
-
-	/* 2 banks */
-	else
-	  {
-	    size_b1 = flash_get_size((vu_long *)FLASH_BASE1_PRELIM, &flash_info[1]);
-
-	    /* Re-do sizing to get full correct info */
-
-	    if (size_b1)
-	      {
-		mtdcr(ebccfga, pb0cr);
-		pbcr = mfdcr(ebccfgd);
-		mtdcr(ebccfga, pb0cr);
-		base_b1 = -size_b1;
-		pbcr = (pbcr & 0x0001ffff) | base_b1 | (((size_b1/1024/1024)-1)<<17);
-		mtdcr(ebccfgd, pbcr);
-		/*          printf("pb1cr = %x\n", pbcr); */
-	      }
-
-	    if (size_b0)
-	      {
-		mtdcr(ebccfga, pb1cr);
-		pbcr = mfdcr(ebccfgd);
-		mtdcr(ebccfga, pb1cr);
-		base_b0 = base_b1 - size_b0;
-		pbcr = (pbcr & 0x0001ffff) | base_b0 | (((size_b0/1024/1024)-1)<<17);
-		mtdcr(ebccfgd, pbcr);
-		/*            printf("pb0cr = %x\n", pbcr); */
-	      }
-
-	    size_b0 = flash_get_size((vu_long *)base_b0, &flash_info[0]);
-
-	    flash_get_offsets (base_b0, &flash_info[0]);
-
-	    /* monitor protection ON by default */
-	    (void)flash_protect(FLAG_PROTECT_SET,
-				base_b0+size_b0-CFG_MONITOR_LEN,
-				base_b0+size_b0-1,
-				&flash_info[0]);
-
-	    if (size_b1) {
-	      /* Re-do sizing to get full correct info */
-	      size_b1 = flash_get_size((vu_long *)base_b1, &flash_info[1]);
-
-	      flash_get_offsets (base_b1, &flash_info[1]);
-
-	      /* monitor protection ON by default */
-	      (void)flash_protect(FLAG_PROTECT_SET,
-				  base_b1+size_b1-CFG_MONITOR_LEN,
-				  base_b1+size_b1-1,
-				  &flash_info[1]);
-	      /* monitor protection OFF by default (one is enough) */
-	      (void)flash_protect(FLAG_PROTECT_CLEAR,
-				  base_b0+size_b0-CFG_MONITOR_LEN,
-				  base_b0+size_b0-1,
-				  &flash_info[0]);
-	    } else {
-	      flash_info[1].flash_id = FLASH_UNKNOWN;
-	      flash_info[1].sector_count = -1;
-	    }
-
-	    flash_info[0].size = size_b0;
-	    flash_info[1].size = size_b1;
-	  }/* else 2 banks */
-	switch_cs(rc); /* switch mode back */
-	return (size_b0 + size_b1);
-}
-
-
-static void flash_get_offsets (ulong base, flash_info_t *info)
-{
-	return;
-}
+	size_b1 = 0 ;
+	flash_info[0].size = size_b0;
 #if 0
-/*-----------------------------------------------------------------------
- */
-static void flash_get_offsets (ulong base, flash_info_t *info)
-{
-	int i;
-
-	/* set up sector start address table */
-  if (((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_SST) ||
-	    (info->flash_id  == FLASH_AM040)){
-		for (i = 0; i < info->sector_count; i++)
-			info->start[i] = base + (i * 0x00010000);
-  }
-  else {
-		if (info->flash_id & FLASH_BTYPE) {
-		/* set sector offsets for bottom boot block type	*/
-		info->start[0] = base + 0x00000000;
-		info->start[1] = base + 0x00004000;
-		info->start[2] = base + 0x00006000;
-		info->start[3] = base + 0x00008000;
-		for (i = 4; i < info->sector_count; i++) {
-			info->start[i] = base + (i * 0x00010000) - 0x00030000;
-		}
-	    } else {
-		/* set sector offsets for top boot block type		*/
-		i = info->sector_count - 1;
-		info->start[i--] = base + info->size - 0x00004000;
-		info->start[i--] = base + info->size - 0x00006000;
-		info->start[i--] = base + info->size - 0x00008000;
-		for (; i >= 0; i--) {
-			info->start[i] = base + i * 0x00010000;
-		}
-	    }
-	}
+	/* include this if you want to test if
+	   the relocation has be done ok.
+	   This will disable both Chipselects */
+	mtdcr (ebccfga, pb0cr);
+	mtdcr (ebccfgd, 0L);
+	mtdcr (ebccfga, pb1cr);
+	mtdcr (ebccfgd, 0L);
+	printf("CS0 & CS1 switched off for test\n");
+#endif
+	return (size_b0);
 }
 
-#endif
+
 /*-----------------------------------------------------------------------
  */
 void flash_print_info  (flash_info_t *info)
 {
 	int i;
-    int k;
-   	int size;
-    int erased;
-    volatile unsigned long *flash;
+	int k;
+	int size;
+	int erased;
+	volatile unsigned long *flash;
 
 	if (info->flash_id == FLASH_UNKNOWN) {
 		printf ("missing or unknown FLASH type\n");
@@ -297,40 +178,30 @@ void flash_print_info  (flash_info_t *info)
 
 	printf ("  Sector Start Addresses:");
 	for (i=0; i<info->sector_count; ++i) {
-  	/*
-     * Check if whole sector is erased
-     */
+		/*
+		 * Check if whole sector is erased
+		*/
 		if (i != (info->sector_count-1))
-    	size = info->start[i+1] - info->start[i];
+			size = info->start[i+1] - info->start[i];
 		else
-      size = info->start[0] + info->size - info->start[i];
-    erased = 1;
-    flash = (volatile unsigned long *)info->start[i];
-    size = size >> 2;        /* divide by 4 for longword access */
-    for (k=0; k<size; k++)
-    {
-    	if (*flash++ != 0xffffffff)
-			{
- 				erased = 0;
+			size = info->start[0] + info->size - info->start[i];
+		erased = 1;
+		flash = (volatile unsigned long *)info->start[i];
+		size = size >> 2;        /* divide by 4 for longword access */
+		for (k=0; k<size; k++) {
+			if (*flash++ != 0xffffffff) {
+				erased = 0;
 				break;
 			}
- 		}
+		}
 		if ((i % 5) == 0)
 			printf ("\n   ");
-#if 0 /* test-only */
-		printf (" %08lX%s",
-			info->start[i],
-			info->protect[i] ? " (RO)" : "     "
-#else
 		printf (" %08lX%s%s",
 			info->start[i],
 			erased ? " E" : "  ",
-			info->protect[i] ? "RO " : "   "
-#endif
-		);
+			info->protect[i] ? "RO " : "   ");
 	}
 	printf ("\n");
-
 }
 
 /*-----------------------------------------------------------------------
@@ -457,21 +328,22 @@ static ulong flash_get_size (vu_long *addr, flash_info_t *info)
 	}
 
 	/* set up sector start address table */
-  if (((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_SST) ||
-	    (info->flash_id  == FLASH_AM040)){
+	if (((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_SST) ||
+	     (info->flash_id  == FLASH_AM040)){
 		for (i = 0; i < info->sector_count; i++)
 			info->start[i] = base + (i * 0x00010000);
-  } else {
+	}
+	else {
 		if (info->flash_id & FLASH_BTYPE) {
-		/* set sector offsets for bottom boot block type	*/
-		info->start[0] = base + 0x00000000;
-		info->start[1] = base + 0x00004000;
-		info->start[2] = base + 0x00006000;
-		info->start[3] = base + 0x00008000;
-		for (i = 4; i < info->sector_count; i++)
-			info->start[i] = base + (i * 0x00010000) - 0x00030000;
-	  }
-	  else {
+			/* set sector offsets for bottom boot block type	*/
+			info->start[0] = base + 0x00000000;
+			info->start[1] = base + 0x00004000;
+			info->start[2] = base + 0x00006000;
+			info->start[3] = base + 0x00008000;
+			for (i = 4; i < info->sector_count; i++)
+				info->start[i] = base + (i * 0x00010000) - 0x00030000;
+		}
+		else {
 			/* set sector offsets for top boot block type		*/
 			i = info->sector_count - 1;
 			if(info->sector_count==71) {
@@ -501,52 +373,41 @@ static ulong flash_get_size (vu_long *addr, flash_info_t *info)
 		/* read sector protection at sector address, (A7 .. A0) = 0x02 */
 		/* D0 = 1 if protected */
 		addr2 = (volatile FLASH_WORD_SIZE *)(info->start[i]);
-    	if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL)
-      	info->protect[i] = 0;
-      else
-        info->protect[i] = addr2[2] & 1;
+		if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL)
+			info->protect[i] = 0;
+		else
+			info->protect[i] = addr2[2] & 1;
 	}
 
 	/*
 	 * Prevent writes to uninitialized FLASH.
 	 */
 	if (info->flash_id != FLASH_UNKNOWN) {
-#if 0 /* test-only */
-#ifdef CONFIG_ADCIOP
-		addr2 = (volatile unsigned char *)info->start[0];
-                addr2[ADDR0] = 0xAA;
-                addr2[ADDR1] = 0x55;
-                addr2[ADDR0] = 0xF0;  /* reset bank */
-#else
 		addr2 = (FLASH_WORD_SIZE *)info->start[0];
 		*addr2 = (FLASH_WORD_SIZE)0x00F000F0;	/* reset bank */
-#endif
-#else /* test-only */
-		addr2 = (FLASH_WORD_SIZE *)info->start[0];
-		*addr2 = (FLASH_WORD_SIZE)0x00F000F0;	/* reset bank */
-#endif /* test-only */
 	}
 	return (info->size);
 }
 
+
 int wait_for_DQ7(flash_info_t *info, int sect)
 {
 	ulong start, now, last;
 	volatile FLASH_WORD_SIZE *addr = (FLASH_WORD_SIZE *)(info->start[sect]);
 
 	start = get_timer (0);
-    last  = start;
-    while ((addr[0] & (FLASH_WORD_SIZE)0x00800080) != (FLASH_WORD_SIZE)0x00800080) {
-        if ((now = get_timer(start)) > CFG_FLASH_ERASE_TOUT) {
-            printf ("Timeout\n");
-            return -1;
-        }
-        /* show that we're waiting */
-        if ((now - last) > 1000) {  /* every second */
-	    			putc ('.');
-            last = now;
-        }
-    }
+	last  = start;
+	while ((addr[0] & (FLASH_WORD_SIZE)0x00800080) != (FLASH_WORD_SIZE)0x00800080) {
+		if ((now = get_timer(start)) > CFG_FLASH_ERASE_TOUT) {
+			printf ("Timeout\n");
+			return -1;
+		}
+		/* show that we're waiting */
+		if ((now - last) > 1000) {  /* every second */
+			putc ('.');
+			last = now;
+		}
+	}
 	return 0;
 }
 
@@ -555,20 +416,20 @@ int intel_wait_for_DQ7(flash_info_t *info, int sect)
 	ulong start, now, last;
 	volatile FLASH_WORD_SIZE *addr = (FLASH_WORD_SIZE *)(info->start[sect]);
 
-		start = get_timer (0);
-    last  = start;
-    while ((addr[0] & (FLASH_WORD_SIZE)0x00800080) != (FLASH_WORD_SIZE)0x00800080) {
-        if ((now = get_timer(start)) > CFG_FLASH_ERASE_TOUT) {
-            printf ("Timeout\n");
-            return -1;
-        }
-        /* show that we're waiting */
-        if ((now - last) > 1000) {  /* every second */
-	    			putc ('.');
-            last = now;
-        }
-    }
-    addr[0]=(FLASH_WORD_SIZE)0x00500050;
+	start = get_timer (0);
+	last  = start;
+	while ((addr[0] & (FLASH_WORD_SIZE)0x00800080) != (FLASH_WORD_SIZE)0x00800080) {
+		if ((now = get_timer(start)) > CFG_FLASH_ERASE_TOUT) {
+			printf ("Timeout\n");
+			return -1;
+		}
+		/* show that we're waiting */
+		if ((now - last) > 1000) {  /* every second */
+			putc ('.');
+			last = now;
+		}
+	}
+	addr[0]=(FLASH_WORD_SIZE)0x00500050;
 	return 0;
 }
 
@@ -621,7 +482,7 @@ int	flash_erase (flash_info_t *info, int s_first, int s_last)
 		if (info->protect[sect] == 0) {	/* not protected */
 			addr2 = (FLASH_WORD_SIZE *)(info->start[sect]);
 			/*  printf("Erasing sector %p\n", addr2); */ /* CLH */
-	    if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_SST) {
+			if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_SST) {
 				addr[ADDR0] = (FLASH_WORD_SIZE)0x00AA00AA;
 				addr[ADDR1] = (FLASH_WORD_SIZE)0x00550055;
 				addr[ADDR0] = (FLASH_WORD_SIZE)0x00800080;
@@ -630,16 +491,16 @@ int	flash_erase (flash_info_t *info, int s_first, int s_last)
 				addr2[0] = (FLASH_WORD_SIZE)0x00500050;  /* block erase */
 				for (i=0; i<50; i++)
 					udelay(1000);  /* wait 1 ms */
-		    wait_for_DQ7(info, sect);
-		  }
-		  else {
-		  	if((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL){
+				wait_for_DQ7(info, sect);
+			}
+			else {
+		  		if((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL){
 					addr2[0] = (FLASH_WORD_SIZE)0x00600060;  /* unlock sector */
 					addr2[0] = (FLASH_WORD_SIZE)0x00D000D0;  /* sector erase */
-			    intel_wait_for_DQ7(info, sect);
+					intel_wait_for_DQ7(info, sect);
 					addr2[0] = (FLASH_WORD_SIZE)0x00200020;  /* sector erase */
 					addr2[0] = (FLASH_WORD_SIZE)0x00D000D0;  /* sector erase */
-			    intel_wait_for_DQ7(info, sect);
+					intel_wait_for_DQ7(info, sect);
 				}
 				else {
 					addr[ADDR0] = (FLASH_WORD_SIZE)0x00AA00AA;
@@ -648,18 +509,18 @@ int	flash_erase (flash_info_t *info, int s_first, int s_last)
 					addr[ADDR0] = (FLASH_WORD_SIZE)0x00AA00AA;
 					addr[ADDR1] = (FLASH_WORD_SIZE)0x00550055;
 					addr2[0] = (FLASH_WORD_SIZE)0x00300030;  /* sector erase */
-			    wait_for_DQ7(info, sect);
-		 		}
-		 }
-		 l_sect = sect;
-		    /*
-		     * Wait for each sector to complete, it's more
-		     * reliable.  According to AMD Spec, you must
-		     * issue all erase commands within a specified
-		     * timeout.  This has been seen to fail, especially
-		     * if printf()s are included (for debug)!!
-		     */
-		 /*   wait_for_DQ7(info, sect); */
+					wait_for_DQ7(info, sect);
+				}
+			}
+			l_sect = sect;
+			/*
+			 * Wait for each sector to complete, it's more
+			 * reliable.  According to AMD Spec, you must
+			 * issue all erase commands within a specified
+			 * timeout.  This has been seen to fail, especially
+			 * if printf()s are included (for debug)!!
+			 */
+			/*   wait_for_DQ7(info, sect); */
 		}
 	}
 
@@ -688,6 +549,7 @@ DONE:
 	return 0;
 }
 
+
 void unlock_intel_sectors(flash_info_t *info,ulong addr,ulong cnt)
 {
 	int i;
@@ -707,8 +569,6 @@ void unlock_intel_sectors(flash_info_t *info,ulong addr,ulong cnt)
 		i++;
 		c-=(info->start[i]-info->start[i-1]);
 	}while(c>0);
-
-
 }
 
 

board/mpl/common/memtst.c

@@ -457,7 +457,7 @@ typedef struct {
 
 
 #define TEST_STAGES 5
-const RAM_MEMTEST_FUNC test_stage[TEST_STAGES] = {
+static RAM_MEMTEST_FUNC test_stage[TEST_STAGES] = {
 	{RAM_MemTest_WriteData1, "data test 1...\n", RAM_MemTest_CheckData1,
 	 NULL},
 	{RAM_MemTest_WriteData2, "data test 2...\n", RAM_MemTest_CheckData2,
@@ -470,9 +470,35 @@ const RAM_MEMTEST_FUNC test_stage[TEST_STAGES] = {
 	 RAM_MemTest_CheckRandomPattern, NULL}
 };
 
+void mem_test_reloc(void)
+{
+	DECLARE_GLOBAL_DATA_PTR;
+	unsigned long addr;
+	int i;
+	for (i=0; i< TEST_STAGES; i++) {
+ 		addr = (ulong) (test_stage[i].test_write) + gd->reloc_off;
+		test_stage[i].test_write=
+			(void (*) (unsigned long startaddr, unsigned long size,
+						unsigned long *pat))addr;
+ 		addr = (ulong) (test_stage[i].test_write_desc) + gd->reloc_off;
+		test_stage[i].test_write_desc=(char *)addr;
+ 		if(test_stage[i].test_check1) {
+			addr = (ulong) (test_stage[i].test_check1) + gd->reloc_off;
+			test_stage[i].test_check1=
+				(void *(*) (int mode, unsigned long startaddr,
+				 unsigned long size, unsigned long *pat))addr;
+		}
+ 		if(test_stage[i].test_check2) {
+			addr = (ulong) (test_stage[i].test_check2) + gd->reloc_off;
+			test_stage[i].test_check2=
+				(void *(*) (int mode, unsigned long startaddr,
+				 unsigned long size, unsigned long *pat))addr;
+		}
+	}
+}
 
 
-int mem_test (unsigned long start, unsigned long ramsize, int quiet)
+int mem_test (unsigned long start, unsigned long ramsize, int quiet, int reloc)
 {
 	unsigned long errors, stage;
 	unsigned long startaddr, size, i;