Without this, when CONFIG_ENV_VARS_UBOOT_CONFIG is active we get
a compile time error when doing 'make env'.
In file included from tools/env/fw_env.c:117:0:
include/env_default.h:110:11: error: expected ‘}’ before ‘CONFIG_SYS_ARCH’
When building U-Boot this is included indirectly by the compiler switch
-include
/home/trdx/git.toradex.com/u-boot-2014.10-toradex/include/linux/kconfig.h
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
By removing this default build target, the "u-boot.kwb" target is not
automatically generated. This fixes a temporary build error when using
out-of-tree builds, as buildman does per default (reported by Simon).
When the full SPL support is added for these targets with the DDR training
code, the "u-boot-spl.kwb" image will be generated automatically.
Users providing a special bin_hdr binary (binary.0) file can always add
this binary file and generate the full firmware image by issuing the
"make u-boot.kwb" command directly.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
The macro to select the I2C address for ECC bus-width detection
was defined incorrectly for the Marvell DB-MV784MP-GP board. This
patch changes the macro to the correct value to fix this issue.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds support for the Marvell DB-88F6820-GP Armada A38x
evaluation board.
Supported peripherals are:
- UART
- Ethernet (mvneta)
- I2C
- SPI (including SPI NOR flash)
Please note that this board support right now only supports the
main U-Boot. Without the bin_hdr integration (DDR training etc). This
will be added in a few days / weeks to complete this board port. But
till then this U-Boot version can be run on the target via the
original Marvell U-Boot via this command:
tftpboot 4000000 db-88f6820-gp/u-boot.bin;go 4000000
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
This solves some RX problems that have been seen, when using the
mvneta ethernet driver. The cache needs to be reset into a "clean"
state before using it.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
With the introduction of the Armada 38x support, its necessary to change
the mvneta ethernet driver init call from always 4 times to a
configurable value. Lets make this init call more flexible by moving
the actually used devices to the config header.
Additionally this patch takes care of the slightly different base
addresses for the ethernet controllers on A38x.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds support for the Marvell Armada 38x SoC family.
Supported peripherals are:
- UART
- Ethernet (mvneta)
- I2C
- SPI (including SPI NOR flash)
Tested on Marvell DB-88F6820-GP evaluation board.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
This way, new MVEBU boards don't need to specifiy the common location
for the SPL linker script.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
This define is used by the DDR training code for Armada XP. With the
upcoming addition of Armada 38x support, lets only define it for
Armada XP in this common header.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Since these files will be used for other MVEBU SoC's, lets reflect this
in the headers marcos as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Move arch/arm/include/asm/arch-armada-xp/*
-> arch/arm/mach-mvebu/include/mach/*
Additionally the SYS_SOC is renamed from "armada-xp" to "mvebu". With this
change all these files can better be shared with other, newer Mavell
MVEBU SoC's. Like the upcoming Armada 38x support.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Move arch/arm/cpu/armv7armada-xp/* -> arch/arm/mach-mvebu/*
Since this platform will be extended to support other Marvell SoC's as
well, lets rename it directly to mvebu.
This will be used by the upcoming Armada 38x suport (A38x).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
The get_timer_us() function is something which is no longer
existing in case we use generic timer framework, so replace
it with get_timer().
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Tyler Baker <tyler.baker@linaro.org>
If the mmc device is non-removable (as indicated by the device tree), set
the flag so that users of the device know.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
We need to clear the allocated memory explicitly as the included
struct sdhci_host has function pointers. Those are compared to NULL to
test if this (optional) feature is supported. Leaving them undefined let
u-boot jump to arbitrary memory.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Freescale eMMC44 adapter card uses Micron N2M400FDB311A3CF eMMC
memory. According to the silicon datasheet, secure erase timeout
is 600ms. So increase erase timeout value from 250ms to 600ms.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Timeout interrupt also work for response busy command(R1b) like
cmd38/cmd6. So need to set it accordingly. Current code only
set timeout for data command.
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
High capacity support is not a host capability, but a device capability
that is queried via the OCR. The flag in the operating conditions
request argument can just be set unconditionally. This matches the Linux
implementation.
[panto] Hand merged and renumbering MMC_MODE_DDR_52MHz.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Starting part of device initialization sets the init_in_progress flag
only if the MMC card did not yet come to ready state and needs to continue
polling. If the card is SD or if the MMC card became ready quickly,
the flag is not set and (if using pre-initialization) the starting
phase will be re-executed from mmc_init function.
Set the init_in_progress flag in all non-error cases. Also, move flags
setting statements around so that the flags are not set in error paths.
Also, IN_PROGRESS return status becomes unnecessary, so get rid of it.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
The polling loops in sd_send_op_cond and mmc_complete_op_cond functions
check the ready flag state at the end of the loop, that is after executing
a delay inside the loop, which, in case of exiting with no error,
is not needed. Also, one of these loops, as well as the loop
in mmc_send_status, have the delay just before exiting on timeout
conditions.
Restructure all these loops to check the respective conditions before making
a delay for the next loop pass, and to appropriately exit without the delay.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Some MMC cards come to ready state quite quickly, so that the respective
flag appears to be set in mmc_send_op_cond already. In this case trying
to continue polling the card with CMD1 in mmc_complete_op_cond is incorrect
and may lead to unpredictable results. So check the flag before polling
and skip it appropriately.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
The previous change to use 'ocr' structure field for storing send_op_cond
command response also stopped using command response directly
outside of mmc_send_op_cond_iter(). Now it becomes possible to use
command structure in mmc_send_op_cond_iter() locally, removing a necessity
to pass it as an argument from the caller.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
The 'op_cond_response' field in mmc structure contains the response
from the last SEND_OP_COND MMC command while making iterational
polling of the card. Later it is copied to 'ocr' field, designed
to contain the OCR register value, which is actually the same
response from the same command. So, these fields have actually
the same data, just in different time periods. It's easier to use
the same 'ocr' field in both cases at once, without temporary using
of the 'op_cond_response' field.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
To replicate:
1. add to include/configs/p1_p2_rdb_pc.h "#define CONFIG_CMD_GPIO"
2. run `make P1020RDB-PC_defconfig`
3. run CROSS_COMPILE=powerpc-linux- make
and you will get:
common/built-in.o: In function `do_gpio':
u-boot/common/cmd_gpio.c:186: undefined reference to `gpio_request'
u-boot/common/cmd_gpio.c:194: undefined reference to `gpio_direction_input'
u-boot/common/cmd_gpio.c:195: undefined reference to `gpio_get_value'
u-boot/common/cmd_gpio.c:200: undefined reference to `gpio_get_value'
u-boot/common/cmd_gpio.c:203: undefined reference to `gpio_direction_output'
u-boot/common/cmd_gpio.c:209: undefined reference to `gpio_free
Signed-off-by: Michael Durrant <mdurrant@arcturusnetworks.com>
Signed-off-by: Oleksandr G Zhadan <oleks@arcturusnetworks.com>
Reviewed-by: York Sun <yorksun@freescale.com>
1. board/freescale/t4qds/t4_rcw.cfg
1.8GHz support is requested as default frequency, so update the rcw.
2. remove un-used configs
configs/T4160QDS_SPIFLASH_defconfig
configs/T4240QDS_SPIFLASH_defconfig
SPI boot is not available on T4QDS, so the configs should be removed.
3. board/freescale/t4qds/MAINTAINERS
Updated MAINTAINERS accordingly.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
[York Sun: revise subject]
Reviewed-by: York Sun <yorksun@freescale.com>
T2080RDB RevC uses new SODIMM 1867MT/s instead of previous 1600MT/s.
So update RCW to support new DDR frequency 1867MT/s by default.
Reserve the old 1600MT/s in comment for users in needed.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The SD clock could be generated by platform clock or peripheral
clock for some platforms. This patch adds peripheral clock
support for T1024/T1040/T2080. To enable it, define
CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add adapter card type identification support by reading
FPGA STAT_PRES1 register SDHC Card ID[0:2] bits. To use this function,
define CONFIG_FSL_ESDHC_ADAPTER_IDENT.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
[York Sun: resolve conflicts in README.fsl-esdhc]
Reviewed-by: York Sun <yorksun@freescale.com>
CS4315 PHY doesn't support phy-reset by software, it
needs to reset it by hardware via CPLD control.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Function dp_ddr_restore is to restore the first 128-byte space
of DDR. However those codes may be optimized out by compiler
since the destination address is at 0x0. In order to avoid
compiler optimization, we restore the space from high address,
which is not at 0x0, to low address.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch defines the 2 flush_dcache_range and invalidate_dcache_range
functions for all the powerpc architecture. Their implementation is
borrowed from the kernel's misc_32.S file and replace the ones from
mpc86xx and ppc4xx since they were equivalent.
This is a fix for the problem introduced by this patch:
http://patchwork.ozlabs.org/patch/448849/
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T1023RDB is a Freescale Reference Design Board that hosts the T1023 SoC.
T1023RDB board Overview
-----------------------
- T1023 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
prioritization and bandwidth allocation
- Memory: 2GB Micron MT40A512M8HX unbuffered 32-bit fixed DDR4 without ECC
- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
- Ethernet interfaces:
- one 1G RGMII port on-board(RTL8211F PHY)
- one 1G SGMII port on-board(RTL8211F PHY)
- one 2.5G SGMII port on-board(AQR105 PHY)
- PCIe: Two Mini-PCIe connectors on-board.
- SerDes: 4 lanes up to 10.3125GHz
- NOR: 128MB S29GL01GS110TFIV10 Spansion NOR Flash
- NAND: 512MB S34MS04G200BFI000 Spansion NAND Flash
- eSPI: 64MB S25FL512SAGMFI010 Spansion SPI flash.
- USB: one Type-A USB 2.0 port with internal PHY
- eSDHC: support SD/MMC card and eMMC on-board
- 256Kbit M24256 I2C EEPROM
- RTC: Real-time clock DS1339 on I2C bus
- UART: one serial port on-board with RJ45 connector
- Debugging: JTAG/COP for T1023 debugging
As well updated T1024RDB to add T1023RDB.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: fix defconfig files]
Reviewed-by: York Sun <yorksun@freescale.com>
Freescale PCIe controllers v3.0 and later need to set bit
CFG_READY to allow all inbound configuration transactions
to be processed normally when in EP mode. However, bit
CFG_READY has been moved from PCIe configuration space to
CCSR PCIe configuration register comparing previous version.
The patch is to set this bit according to PCIe version.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T2080QDS PEX1/Slot#1 will down-train from x4 to x2,
with SRDS_PRTCL_S1 = 0x66 and SRDS_PRTCL_S2 = 0x15.
Soft reset PCIe can fix this issue.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds SD boot support for T4240RDB board. SPL
framework is used. PBL initializes the internal RAM and
copies SPL to it. Then SPL initializes DDR using SPD and
copies u-boot from SD card to DDR, finally SPL transfers
control to u-boot.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
[York Sun: Fix T4240RDB_SDCARD_defcofig]
Reviewed-by: York Sun <yorksun@freescale.com>
Add a delay of 1 microsecond before issuing soft reset to the
controller to let ongoing ULPI transaction complete.
This prevents corruption of ULPI Function Control Register which
eventually prevents phy clock from entering to low power mode
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Commit 96d2bb952b ("powerpc/mpc85xx: Don't relocate exception vectors")
simplified IVOR initialization a bit too much, failing to use the
post-relocation offset. This doesn't cause a problem with normal NOR
boot, in which both the pre-relocation and post-relocation addresses
are 64 KiB aligned. However, if TEXT_BASE is only 4 KiB aligned, such
as for NAND/SD/etc. boot on some targets, as well as the QEMU target,
the post-relocation address will not be the same in the lower 16 bits,
as reserve_uboot() ensures that the relocation address is always 64
KiB aligned even if the pre-relocation address was not.
Use the GOT to get the proper post-relocation offsets.
Fixes: 96d2bb952b ("powerpc/mpc85xx: Don't relocate exception vectors")
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
Tested-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Once we add support for the ohci controller the phy-init and phy-power-on
functions may be called twice (once by the ehci code and once by the ohci
code) protect them against this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The 2/3 usb-phys on the sunxi SoCs are really a single separate functional
block, and are modelled as such in devicetree. So once we've moved all the
sunxi usb code to the driver-model then phy_probe will be called once
for the entire block from the driver-model enumeration code.
Move to this now as this also avoids problems with phy_probe being called
multiple times once we introduce ohci support. This also allows us to get rid
of the sunxi_usb_phy_enabled_count variable as phy_probe now is guaranteed
to be called only once.
Since we're effectively rewriting the probe / remove functions, move them
to the end of the file while we are at it, as that is the most logical place
for them.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The usbc.? files now only contain usb-phy related code, rename them to make
this clear.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Rename the sunxi_usbc_foo functions to sunxi_usb_phy_bar to make it clear
that these are usb-phy functions. Also change the verbs & nouns in the suffix
to match the verbs & nouns used in the Linux kernels generic phy framework.
This patch purely renames things, it contains no functional changes.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This is the only function left in sunxi/usbc.c which is not phy related,
so remove it.
This is a preparation patch for turning the usbc.c code into a proper
usb phy driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The sunxi "usbc" code is mostly about phy setup, but currently also sets up
the host controller clocks, which is something which really belongs in the
host controller drivers, so move it there.
This is a preparation patch for moving the sunxi ehci code to the driver
model and for adding ohci support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Now that all sunxi boards are using driver-model for gpio (*), we can remove
the non driver-model support from the axp gpio code, and the glue to call
into the axp gpio code from the sunxi_gpio non driver-model code.
*) For the regular u-boot build, SPL still uses non driver-model gpio for
now, but the SPL never uses axp gpios support and we were already not building
axp-gpio support for the SPL.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
All sunxi boards now use the driver-model, so remove the non driver-model
code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Now that we've everything prepared for it remove the DM settings from the
defconfig(s) and simply always set them for sunxi.
This makes all sunxi boards allways use the driver model for gpios and
ethernet, and allows us to move over more bits to the driver-model without
the need to introduce #ifdef-ery for boards which are not yet using DM.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This is a preparation patch for switching all sunxi boards over to using
the driver model.
Note that rather then defining both CONFIG_DEFAULT_DEVICE_TREE (for u-boot)
and CONFIG_FDTFILE (for the kernel), this commit simply replaces all
CONFIG_FDTFILE defconfig settings with CONFIG_DEFAULT_DEVICE_TREE and
uses CONFIG_DEFAULT_DEVICE_TREE for setting the default fdtfile env value
in sunxi-common.h .
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
u-boot has support for a number of boards for which a dts file still needs
to be written, add minimal dts files for these boards so that we can switch
them over to driver-model / fdt.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We need dts files for all boards we support, so bring in a few unmerged ones,
these will be replaced with the upstream merged versions the next time we
sync dts files.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Bring all the sunxi dts files (and update existing ones) from
mripard/sunxi/dt-for-4.1 (which will be merged into upstream master any
day now). This is necessary so that we can move all sunxi boards over to
the driver model.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Modify the sunxi-emac eth driver to support driver model.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Stefan Roese <sr@denx.de>
Besides being spelled wrong, the DMA_CPU_TRRESHOLD define actually has
nothing to do with DMA as we only use mmio fifo access. Rename it to
EMAC_RX_BUFSIZE to properly reflect what it does.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Stefan Roese <sr@denx.de>
Split all the core functionality out into functions taking a
struct emac_eth_dev *priv argument as preparation for adding driver-model
support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Stefan Roese <sr@denx.de>
This is a preparation-patch for adding device-model support to the emac
driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Stefan Roese <sr@denx.de>
netdev.h should not be included in driver-model enabled builds (doing so
causes compiler warnings about struct eth_driver not being declared), but
we do use sunxi_gmac_initialize in the driver-model case, so move it out of
netdev.h .
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add driver-model support to the axp_gpio code, note that this needs a small
tweak to the driver-model version of sunxi_name_to_gpio to deal with the
vbus detect and enable pins which are not standard numbered gpios.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Move the axp-gpio code out of the drivers/power/axp*.c code, and into
a new separate axpi-gpio driver.
This change drops supports for the gpio3 pin on the axp209, as that requires
special handling, and no boards are using it.
Besides cleaning things up by moving the code to a separate driver, as
a bonus this change also adds support for the (non vusb) gpio pins on the
axp221 and the gpio pins on the axp152.
The new axp-gpio driver gets its own Kconfig option, and is only enabled
on boards which need it. Besides that it only gets enabled in the regular
u-boot build and not for the SPL as we never need it in the SPL.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for the axp152 and axp209 PMICs to the pmic register access
helpers. This is a preparation patch for moving the axp gpio code to a
separate gpio driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Move the register helpers used to access the registers via p2wi resp.
rsb bus on the otherwise identical axp221 and axp223 pmics to a separate
file, so that they can be used by the upcoming standalone axp gpio driver
too.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Change the axp_gpio_foo function prototypes to match the gpio uclass op
prototypes, this is a preparation patch for moving the axp gpio code to
a separate driver-model gpio driver.
Note that the ugly calls with a NULL udev pointer in drivers/gpio/sunxi_gpio.c
this adds are removed in a later patch.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
When doing a driver-model enabled build we still need sunxi_name_to_gpio_bank
(for now) for the mmc pinmux code in board/sunxi/board.c, so build it for
driver-model enabled builds too.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
We want to use driver-model/fdt with other model SoCs too, so add
compatible strings for the other SoCs to the dm sunxi gpio code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Until sunxi moves to device tree (e.g. for USB) we need to convert named
GPIOs to numbers. Add a function to do this.
This fixes the USB / EHCI support not working on the LinkSprite pcDuino3
(which uses devicemodel).
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
By convention, sunxi GPIOs are named PA1, PA2 instead of A1, A2. Change
the driver model GPIO driver for sunxi to use these names.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
i2c_init_board() gets called before the driver-model (gpio) code is
initialized, so move the setup of the soft-i2c pins out of i2c_init_board()
and into board_init(), at which time the driver-model setup has been done.
Also add proper error checking and properly request the gpios as that is
mandatory with the driver-model.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The driver-model gpio functions may return another value then -1 as error,
make the sunxi display code properly handle this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The driver-model gpio functions may return another value then -1 as error,
make the sunxi usbc properly handle this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The driver-model gpio functions may return another value then -1 as error,
make the sunxi mmc code properly handle this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This fixes the following errors being printed during boot:
Error, wrong i2c adapter 0 max 0 possible
Error, wrong i2c adapter 0 max 0 possible
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add a defconfig for generic 7" tablets using the Ippo q8h v1.2 pcb,
with an A33 SoC (the pcb can take an A23 or an A33), and a 1024x600 LCD.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for the new second DRAM PLL found on the A33 SoC.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This is a preparation patch for adding A33 support, which will have a
mach name of sun8i-a33.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
sun6i and newer (derived) SoCs such as the sun8i-a23, sun8i-a33 and sun9i
have a various things in common, like having separate ahb reset control
registers, the SID living inside the pmic, custom pmic busses, new style
watchdog, etc.
This commit introduces a new hidden SUNXI_GEN_SUN6I Kconfig bool which can be
used to check for these features avoiding the need for an ever growing list
of "#if defined CONFIG_MACH_SUN?I" conditionals as we add support for more
"new style" sunxi SoCs.
Note that this commit changes the behavior of the gmac and hdmi code for
sun8i and the upcoming sun9i devices. This does not matter as sun8i does
not have gmac nor hdmi, and sun9i has new hardware-blocks for these so
the old code will not work there.
Also this is intentional as if a sun8i / sun9i variant which does use the
old hwblocks shows up then the GEN_SUN6I code paths will be the right ones
to use.
For completeness this also adds a SUNXI_GEN_SUN4I bool for A10/A13/A20.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
We do not use irqs in u-boot so remove the unused irq field, and all the
#ifdef-ery around the irq initialization.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
There is no reason not to and this make the #ifdef-ery easier to read.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Enable the CPU uclass and Simple Firmware interface for Minnowbaord MAX. This
enables multi-core support in Linux.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This driver supports multi-core init and sets up the CPU frequencies
correctly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This permits init of additional CPU cores after relocation and when driver
model is ready.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Since we do these sorts of operations a lot, it is useful to have a simpler
API, similar to clrsetbits_le32().
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Most modern x86 CPUs include more than one CPU core. The OS normally requires
that these 'Application Processors' (APs) be brought up by the boot loader.
Add the required support to U-Boot to init additional APs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a function to return the address of the Interrupt Descriptor Table.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When we start up additional CPUs we want them to use the same Global
Descriptor Table. Store the address of this in global_data so we can
reference it later.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a subset of this header file from Linux 4.0 to support atomic operations
in U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a simple command which provides access to a list of available CPUs along
with descriptions and basic information.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This provides a way of passing information to Linux without requiring the
full ACPI horror. Provide a rudimentary implementation sufficient to be
recognised and parsed by Linux.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is useful to be able to keep track of the available CPUs in a multi-CPU
system. This uclass is mostly intended for use with SMP systems.
The uclass provides methods for getting basic information about each CPU.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a function similar to print_size() that works for frequencies. It can
handle from Hz to GHz.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Before adding one more function, create a separate header to help reduce
the size of common.h. Add the missing function comments and tidy up.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This is annoying during development and serves no useful purpose since
warnings are clearly displayed now that we are using Kbuild. Remove this
option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some device tree nodes do not have compatible strings but do require
drivers. This is pretty rare, and somewhat unfortunate. Add a function
to permit creation of a driver for any device tree node.
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that reset_cpu() functions correctly, use it instead of directly
accessing the port on boards that use a Firmware Support Package (FSP).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Now that reset_cpu() functions correctly, use it instead of directly
accessing the port.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Now that reset_cpu() functions correctly, use it instead of directly
accessing the port.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The existing code is pretty ancient and is unreliable on modern hardware.
Generally it will hang.
We can use port 0xcf9 to initiate reset on more modern hardware (say in the
last 10 years). Update the reset_cpu() function to do this, and add a new
'full reset' function to perform a full power cycle.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
U-Boot on coreboot does not have a driver for the PCH so cannot see the
SPI peripheral now that it has moved inside the PCH. Add a simple driver so
that SPI flash works again.
Signed-off-by: Simon Glass <sjg@chromium.org>
Currently all x86 boards still use CONFIG_SYS_EXTRA_OPTIONS to define
the text base address. Since it is deprecated, just remove it and use
CONFIG_SYS_TEXT_BASE directly.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Since all x86 boards have been converted to use DM_SPI and
DM_SPI_FLASH, move them to arch/Kconfig x86 section.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Remove the ending period of the MARK_GRAPHICS_MEM_WRCOMB option. Also
fix the indention of its help text.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Move platform-specific options under in arch/x86/Kconfig forward right
after the board-specific options but before any architecture-specific
options. When it comes to the same Kconfig option, board-specific one
takes take the highest precedence, then platform-specific one, and
finally architecture-specific one.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Let arch/x86/Kconfig prompt board vendor first, then select
the board model under that vendor. This way arch/x86/Kconfig
only needs concern board vendor and leave the supported target
list to board/<vendor>/Kconfig.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
By default the legacy segments (A0000h-B0000h, E0000h-F0000h)
do not decode to system RAM. Turn on the decode so that we can
write configuration tables in the F segment.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Previously the PIRQ routing table sanity check was performed against
the original table provided by the platform codes. Now we switch to
check its sanity on the final table in the F segment as this one is
the one seen by the OS.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
There are 6 banks:
4 banks for CORE: available in S0 mode
2 banks for SUS (Suspend): available in S0-S5 mode
Signed-off-by: Gabriel Huau <contact@huau-gabriel.fr>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The descriptor provided with the FSP does not seem to work. Update the
instructions to use the descriptor from the original Intel firmware.
Signed-off-by: Simon Glass <sjg@chromium.org>
For x86, vga_info->BIOSImage points to 0xc0000 which cannot be freed.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
We should pass a u32 class number to pci_rom_probe() instead of a u16.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Implement Intel Queensbay platform-specific PIRQ routing support.
The chipset PIRQ routing setup is called in the arch_misc_init().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
On x86 boards, platform chipset receives up to four different
interrupt signals from PCI devices (INTA/B/C/D), which in turn
will be routed to chipset internal PIRQ lines then routed to
8259 PIC finally if configuring the whole system to work under
the so-called PIC mode (in contrast to symmetric IO mode which
uses IOAPIC).
We add two major APIs to aid this, one for routing PIRQ and the
other one for generating a PIRQ routing table.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
We can write the configuration table in last_stage_init() for all x86
boards, but not with coreboot since coreboot already has them.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add a function to assign an IRQ number to PCI device's interrupt
line register in its configuration space, so that the PCI device
can have its interrupt working under PIC mode after OS boots up.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Create a default e820 table with 3 entries which is enough to boot
a Linux kernel.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Since Intel ICH SPI driver has been converted to driver model, we need
add an alias for SPI node in the board dts files otherwise SPI flash
won't be detected due to 'invalid bus' error.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
For starting a Linux console on the superio serial port under
interrupt mode, the IRQ number must be configured.
Signed-off-by: Jian Luo <jian.luo4@boschrexroth.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Since all x86 boards use spi flash as its bootloader storage media,
it makes sense to make CONFIG_ENV_IS_IN_SPI_FLASH a common option.
So far only minnowmax board does not support it so undefine it in
its board configuration file.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The prefix PCH was taken from ivybridge port. However Queensbay
platform official document does not mention PCH. It is composed
of TunnelCreek processor and Topcliff IOH chipset. For accuracy,
avoid using PCH prefix in the macro.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The comment line in arch/arm/cpu/armv7/zynq/config.mk says that
the option "-mfpu=neon" is necessary for compiling lowlevel_init.S.
We do not have to give it to all the source files.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Provide an option to write filesystem independend commands.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Added the SPI driver support for ZynqMP
The controller is same as zynq SPI controller
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Enable the i2c driver for ZynqMP
Also enable the eeprom for read and writes
to eeprom on ZynqMP
ZynqMP uses the same i2c controller as in Zynq
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Fix wrong timer calculation in get_timer_masked incase of
overflow.
This fixes the issue of getting wrong time from get_timer()
calls.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove the quirk SDHCI_QUIRK_NO_CD as it is not
required.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for loading sw for R5 with enabling for zynqmp.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Disable all level shifters before enabling
the PS-to-PL level shifters as it would
be good to disable all level shifters before
enabling the PS-to-PL in order to ensure that
it is in proper state
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
We are about to change the location for ps7_init files, breaking the
current work-flows. It is good time to drop the legacy ps7_init.c/h
support.
Going forward, please use ps7_init_gpl.c/h all the time.
If you are still using old Xilinx tools that are only able to
generate ps7_init.c/h, rename them into ps7_init_gpl.c/h.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The PicoZed is a System-on-Module board which is marketed as part of
the ZedBoard/MicroZed/etc. collection. It includes a Zynq-7000
processor.
This patch adds support that covers all the variants of the PicoZed
including the SKUs with Z7010/Z7020 and Z7015/Z7030 Zynq chips. This
patch set however only covers support for the System-on-Module and does
not cover any extra components that are available on carrier boards
(except those that are fanned out of the module itself).
More information on this board, its variants and available carrier
boards is available at: http://zedboard.org/product/picozed
Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
On slow platforms not all baudrate setting is valid.
Check it directly in the driver and setup maximum possible
frequency.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Most of the code is taken (and adapted) from Linux kernel driver.
Just add CONFIG_ZYNQ_GPIO to you config to enable it
Signed-off-by: Andrea Scian <andrea.scian@dave.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
It is possible for CONFIG_XILINX_EMACLITE to be defined without
XILINX_EMACLITE_BASEADDR being defined as the EMAC Lite driver support
OF init. Check that the driver is enabled and the base address is
available before initializing with a static base address.
Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
These functions now rely on uclass_find_first/next_device() and assume that
they will either return failure (-ve error code) or a device. In fact,
coming to the end of a list is not considered failure and they return 0
in that case.
The logic to deal with this was replaced in commit acb9ca2a with just using
uclass_get_device_tail(). Add back the missing logic. This bug was
caught by unit tests but since they were broken for other reasons at the
time, this was not noticed.
Signed-off-by: Simon Glass <sjg@chromium.org>
This was accidentally added by commit dd0b0122ba
"serial: ns16550: Add an option to specify the debug UART register shift".
Remove it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Simon Glass <sjg@chromium.org>
Upto now flash sector_size is assigned from params which isn't
necessarily a sector size from vendor, so based on the SECT_*
flags from flash_params the erase_size will compute and it will
become the sector_size finally.
Bug report (from Bin Meng):
=> sf probe
SF: Detected SST25VF016B with page size 256 Bytes, erase size 4 KiB,
total 2 MiB, mapped at ffe00000
=> sf erase 0 +100
SF: 65536 bytes @ 0x0 Erased: OK
Signed-off-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Reported-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
With SPI flash moving to driver model, commit fbb0991 "dm: Convert
spi_flash_probe() and 'sf probe' to use driver model" ignored the
SST flash-specific write op (byte program & word program), which
actually broke the SST flash from wroking.
This commit makes SST flash work again under driver model, by adding
SST flash-specific handling in the spi_flash_std_write().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Add a new member 'flags' in struct spi_flash to store the flash flags
during spi_flash_validate_params().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Instead of hardcoding the 'fdtfile' variable, let's detect the SoC and
board variant on the fly and change the dtb name.
Based on the scheme done on am335x board.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-By: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
README file suggests to use 'fdtfile' for the dtb file name and
'fdt_addr_r' for the dtb address in RAM, so do as suggested.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Introduce is_hummingboard() function that reads GPIOs that can distinguish
between Cubox-i and Hummingboard.
Print the board name accordingly.
Based on a patch from Rabeeh Khoury.
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Cubox-i and Hummingboard support several MX6 SoCs: mx6solo, mx6dual-lite,
mx6dual and mx6quad. Add support for the different SoC/memory sizes
combinations.
DDR initialization values were extracted from Solid-run internal U-boot.
Tested on a CuBox-i4Pro, HummingBoard-i2eX and HummingBoard-i1.
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Cubox-i and Hummingboard support several MX6 SoCs: mx6solo, mx6dual-lite,
mx6dual and mx6quad.
Use IOMUX_PADS() macro in order to prepare for the multi-SoC support.
Also pass 'MX6QDL' in the defconfig to indicate it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add device-tree handover to Linux kernel conforming with MIPS UHI [1].
Register $a0 will be set to the reserved value -2. The address of
the device-tree blob will be stored as KSEG0 address in $a1. $a2 and
$a3 are set to zero.
[1] http://prplfoundation.org/wiki/MIPS_documentation
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
After syncing the sunxi dts files with the upstream kernel dm/fdt sunxi
builds would no longer boot.
The problem is that stdout-path is now set like this in the upstream dts
files: stdout-path = "serial0:115200n8". The use of options in of-paths,
either after an alias name, or after a full path, e.g. stdout-path =
"/soc@01c00000/serial@01c28000:115200", is standard of usage, but something
which the u-boot dts code so far did not handle.
This commit fixes this, adding support for both path formats.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
This erratum requires setting GLITCH_EN bit in debug register to
enable digital filter to improve clock stability.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Heiko Schocher <hs@denx.de>
Enable NAND boot support using SPL framework. To boot from
NAND, either use DIP switches on board, or "qixis_reset nand"
command. Details of forming NAND image can be found in README.
Signed-off-by: Scott Wood <scottwood@freescale.com>
[York Sun: Remove +S from defconfig after commit 252ed872]
Signed-off-by: York Sun <yorksun@freescale.com>
This adds NAND boot support for LS2085AQDS, using SPL framework.
Details of forming NAND image can be found in README.
Signed-off-by: Scott Wood <scottwood@freescale.com>
[York Sun: Remove +S from defconfig after commit 252ed872]
Signed-off-by: York Sun <yorksun@freescale.com>
IFC has two register pages.Till IFC version 1.4 each
register page is 4KB each.But IFC ver 2.0 register page
size is 64KB each.IFC regiters structure is break into
two viz FCM and RUNTIME.FCM(Flash control machine) registers
are defined in PAGE0 and controls IFC generic functionality.
RUNTIME registers are defined in PAGE1 and controls NAND and
GPCM funcinality.
FCM and RUNTIME structures defination is common for IFC
version 1.4 and 2.0.
Signed-off-by: Jaiprakash Singh <b44839@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Add support of ethernet:
- eth.c: mapping lane to slot for (0x2A, 0x07)
- ls2085a.c: To enable/disable dpmac and get link type
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
This adds initial support for Colibri VF50/VF61 based on Freescale
Vybrid SoC.
- CPU clocked at 396/500 MHz
- DDR3 at 396MHz
- for VF50, use PLL2 as memory clock (synchronous mode)
- for VF61, use PLL1 as memory clock (asynchronous mode)
- Console on UART0 (Colibri UART_A)
- Ethernet on FEC1
- PLL5 based RMII clocking (E.g. No external crystal)
- UART_A and UART_C I/O muxing
- Boot from NAND by default
Tested on Colibri VF50/VF61 booting using serial loader over UART.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Enables caches which provides a rather huge speedup of the boot loader.
Also mark the on-chip RAM as cachable since this is the area U-Boot runs
from.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Vybrid product family consists of several rather similar SoC which
can be determined by softare during boot time. This allows use of
variable ${soc} for Linux device tree files. Detect VF5xx CPU's by
reading the CPU count register. We can determine the second number
of the CPU type (VF6x0) which indicates the presence of a L2 cache.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Enable the SCSC (Slow Clock Source Controller) and select the external
32KHz oscillator. This improves the accuracy of the RTC.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
In order to avoid code duplication, move the DDR3 initialization to the
common place under imx-common. Currently ROW_DIFF and COL_DIFF can be
chosen from the board file. The JEDEC timings are specified using a
common ddr3_jedec_timings structure.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Some RTC chips tend to set garbage date after reset.
This patch sets the date to 2000-01-01 00:00 immediatelly
after the RTC chip reset is issued using the "date reset"
command.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Add architecture-specific u-boot.lds and remove all board-specific
u-boot.lds.
All the .text customization that was board-specific have been
moved inside the related include/configs, inside a
LDS_BOARD_TEXT define.
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Implemented fb_set_reboot_flag() for OMAP5 to set
an environment variable 'dofastboot' when reboot-bootloader called.
This environment variable will be checked in boot command and fastboot
will be called if the variable is set.
If the bootcmd env variable of OMAP5 common is overwritten with board-specific
command, then these changes will not apply.
This was originally intended for DRA7 platform, but now applies to all OMAP5.
Ref:
http://git.omapzoom.org/?p=repo/u-boot.git;a=commit;h=19da2e436e9806259cf1f4988b9e046ab256bf2c
Signed-off-by: Angela Stegmaier <angelabaker@ti.com>
Signed-off-by: Dileep Katta <dileep.katta@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Make it check for !CONFIG_ENV_IS_NOWHERE as we can't saveenv()
in that case]
Signed-off-by: Tom Rini <trini@konsulko.com>
For the local project, we may specified format.subjectprefix setting.
Then the patch will be formated as [Project_prefix][PATCH].
But patman will not check this setting. It will remove the
format.subjectprefix.
So This patch will let patman check this setting and add it as a
project prefix.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Also read gcc 4.9.0 at kernel.org which also have Microblaze toolchain.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Fixed unit test failure by updating the test:
Signed-off-by: Simon Glass <sjg@chromium.org>
The Marvell GPIO driver can be used on Marvell platforms other than
Sheeva, so remove the ifdef to enable it for others.
Signed-off-by: Rob Herring <robh@kernel.org>
1. The bits 11..10 for mfp driver strength is only valid for
aspen and old xscale family, for newer Marvell chip, this range
has been moved to 12..11.
2. add sleep bit support
Signed-off-by: Xiang Wang <wangx@marvell.com>
[robh: rebase to current mainline]
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Howard <phoward@gme.net.au>
[trini: Add config file, update for ..._ether_addr() -> ..._ethaddr() rename]
Signed-off-by: Tom Rini <trini@konsulko.com>
The LS2085AQDS is an evaluatoin platform that supports the LS2085A
family SoCs. This patch add basic support of the platform.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Wire rate IO Processor (WRIOP) provide support of receive and transmit
ethernet frames from the ethernet MAC. Here Each WRIOP block supports
upto 64 DPMACs.
Create a house keeping data structure to support upto 16 DPMACs and
store external phy related information.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
The memac for PHY management on little endian SoCs is similar on big
endian SoCs, so we modify the driver by using I/O accessor function to
handle the endianness, so the driver can be reused on little endian
SoCs, we introduce CONFIG_SYS_MEMAC_LITTLE_ENDIAN for little endian
SoCs, if the CONFIG_SYS_MEMAC_LITTLE_ENDIAN is defined, the I/O access
is little endian, if not, the I/O access is big endian. Move fsl_memac.h
out of powerpc include.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Changed MC firmware loading to comply with the new MC boot architecture.
Flush D-cache hierarchy after loading MC images. Add environment
variables "mcboottimeout" for MC boot timeout in milliseconds,
"mcmemsize" for MC DRAM block size. Check MC boot status before calling
flib functions.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Add support of SerDes framework for Layerscape Architecture.
- Add support of 2 SerDes block
- Add SerDes protocol parsing and detection
- Create table of SerDes protocol supported by LS2085A
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Fix flush_dcache_range() input parameter to use start and end addresses.
Change ethernet interface name to DPNI. Update entry criteria for
ldpaa_eth_stop. Ethernet stack first stop the device before performing
next operation. At the time of Ethernet driver registration,
net_dev->state is set as ETH_STATE_INIT So take care net_dev->state as
ETH_STATE_INIT in ldpaa_eth_stop.
Undef CONFIG_PHYLIB temorarily because ldpaa_eth driver currently does
not support PHYLIB.
Instead of clearing pull descriptor one time, clear it before issuing any
volatile dequeue command.
Volatile command does not return frame immidiately, wait till a frame
is available in DQRR. This frame can be valid or expired.
Flush buffer before releasing to BMan ensure the core does not have any
cachelines that the WRIOP will DMA to.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: pankaj chauhan <pankaj.chauhan@freescale.com>
Signed-off-by: Roy Pledge <Roy.Pledge@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
The serial nodes in the fsl-lsch3 device trees have compatible =
"fsl,ns16550", "ns16550a" -- so don't look for "ns16550".
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Without this "USB may not work" according to the erratum text, though I
did not notice a problem without it.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
During booting, IFC is mapped to low region. After booting up, IFC is
remapped to high region for larger space. The environmental variables are
also stored at high region. In order to read the variables during booting,
a virtual mapping is required.
Cache was enabled for entire IFC space before. Actually the first two
entries are big enough (4MB) to cover the boot code and environmental
variables. Remove extra entries. Move OCRAM entry out of ifdef.
Signed-off-by: York Sun <yorksun@freescale.com>
The timer clock is system clock divided by 4, not fixed 12MHz.
This is common to the SoC, not board specific. Primary core is
fixed when u-boot still runs in board_f. Secondary cores are
fixed by reading a variable set by u-boot.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Mark Rutland <mark.rutland@arm.com>
Platform clock is half of platform PLL. There is an additional divisor
in place. Clean up code copied from powerpc.
Signed-off-by: York Sun <yorksun@freescale.com>
ls2085a_common.h contains hard-coded information for NOR/NAND flash,
I2C, DDR, etc. These are platform specific. Move them out of common
header file and placed into respective board header files.
Move TEXTBASE to 1MB offset to fit NOR flash with up to 1MB sector
size.
Enable command auto complete. Update prompt symbol. Set fdt_high to
0xa0000000 because Linux requires that the fdt be 8-byte aligned
and below 512 MiB. Besides ensuring compliance with the 512 MiB
limit, this avoids problems with the dtb being misaligned within
the FIT image.
Change the MC FW, MC DPL and Debug server NOR addresses in compliance
with the NOR flash layouts for 128MB flash.
Add PCIe macros. Enable "loadb" command. Disable debug server.
Enable workaround for erratum A008511.
Stop reset on panic for postmortem debugging.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Generic Timer may contain an erroneous value. The workaround is to
read it twice until getting the same value.
Signed-off-by: York Sun <yorksun@freescale.com>
This erratum only applies to general purpose DDR controllers in LS2.
It shouldn't be applied to DP-DDR controller. Check DDRC versoin number
before applying workaround.
Signed-off-by: York Sun <yorksun@freescale.com>
Add built-in memory test to catch errors after DDR is initialized, before
any other transactions. To enable this test, define CONFIG_FSL_DDR_BIST.
An environmental variable "ddr_bist" is checked before starting test.
It takes a while (several seconds) depending on system memory size.
Signed-off-by: York Sun <yorksun@freescale.com>
CS0 was not allowed to be empty by u-boot driver in the past to simplify
the driver. This may be inconvenient for some debugging. This patch lifts
the restrictions. Controller interleaving still requires CS0 populated.
Signed-off-by: York Sun <yorksun@freescale.com>
Add/update registers for DDR4, including DQ mappings. Allow raw timing
method used for all controllers. Update mode_9 register to 0x500 for
improved stability. Check DDR controller version number individually
in case a SoC has multiple DDR controllers of different versions.
Increase read-write turnaround for DDR4 high speeds.
Signed-off-by: York Sun <yorksun@freescale.com>
Some SoCs have more than two I2C busses. Instead of adding ifdef
to the driver, macros are put into board header file where
CONFIG_SYS_I2C_MXC is defined.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Heiko Schocher <hs@denx.de>
IFC 2.0 doubled the SRAM size, which means double the number of
ECCSTAT registers. Fix the resulting array overflow.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
For fsl-lsch3, IFC is binded with address within 32-bit at fist.
After u-boot relocates to DDR, CS1, CS3 can be binded to higher
address to support large space.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
LDPAA Ethernet driver is a freescale's new ethernet driver based on
Layerscape architecture.
Every ethernet driver controls on DPNI object. Where all DPNIs share
one common DPBP and DPIO object to support Rx and Tx flows.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
CC: Cristian Sovaiala <cristian.sovaiala@freescale.com>
CC: Bogdan Hamciuc <bogdan.hamciuc@freescale.com>
CC: J. German Rivera <German.Rivera@freescale.com>
[York Sun: s/NetReceive/net_process_received_packet]
Reviewed-by: York Sun <yorksun@freescale.com>
Some boards cannot support device tree due to lack of memory. Add an option
to allow these boards to continue to work (and even use driver model).
This is a 'negative' option since most boards are expected to support device
tree in SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
There is little reason to split these two functions. Bring them together
which simplifies the init sequence.
Signed-off-by: Simon Glass <sjg@chromium.org>
When CONFIG_DM_DEVICE_REMOVE is not enabled, such as in SPL, we cannot
remove or unbind devices and do not expect to get errors when binding
and probing devices. So drop the error path to reduce code size.
Signed-off-by: Simon Glass <sjg@chromium.org>
The printf() in panic() adds about 1.5KB of code size to SPL when compiled
with Thumb-2. Provide a smaller version that does not support printf()-style
arguments and use it in two commonly compiled places.
Signed-off-by: Simon Glass <sjg@chromium.org>
The CONFIG_DM_DEVICE_REMOVE option takes out code related to removing
devices. It should also remove the 'unbind' code since if we cannot
remove we probably don't need to unbind.
Signed-off-by: Simon Glass <sjg@chromium.org>
In many cases SPL only uses a single serial port and there is no need for
alias sequence support. We will just use the serial port pointed to by
stdout-path in the /chosen node.
Signed-off-by: Simon Glass <sjg@chromium.org>
This reverts commit 562f8df18d.
Note: Even un-reverting this patch couldn't works as expected, based
on the latest testing from Heiko Schocher.
Signed-off-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
This patch extends the U-Boot "led" command to support automatic blinking
by setting a blink frequency in milliseconds. Additionally the number of
supported LEDs is increased to 6 (0...5).
This will be used by the PCA9551 LED driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
This assignment conflicts with code that add flags with
gd->flags |= FOO prior to the execution of this function.
Seems like a historical artifact and creates bugs with
early alloc().
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Simon Glass <sjg@chromium.org>
Select integrator boards by the combination of platform select (AP/CP)
and core module select (CM720T, CM920T, ...).
This allows us to remove CONFIG_SYS_EXTRA_OPTIONS and make Kconfig
much cleaner.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
The board/SoC select menu in arch/arm/Kconfig is still cluttered.
Add ARCH_INTEGRATOR into arch/arm/Kconfig and move the board select
under arch/arm/mach-integrator.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
These is a growing trend to license DT files dual GPL and X11
especially in the Linux community. It allows easier reuse of
device trees for other software projects.
This commit prepares for doing so in U-Boot too, since DT files are
often copied from the kernel to U-Boot.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Commit d8bafe1310
"ARMv8: enable DM in vexpress64 board" only enabled DM
for the simulated vexpress64 board (FVP) with the
hardcoded clock value for the simulated board, causing
a console regression on the Juno board which was using
a different clock setting.
Fix this by enabling DM for all vexpress64 boards,
defining the clock frequency per-board, deleting the
static array of PL01x ports from the config file and
relying solely on the port defined in the boardfile
using platform data.
Cc: David Feng <fenghua@phytium.com.cn>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
some pins on the board have been rerouted to other peripherals, so we
change the pinmux to apply with hardware-design.
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
The NAND-version has been become a bit orphan.
Now we need to reactivate it, so bring necessary things:
- loading devicetree
- switch control signal to correct pins
- setup pinmux
- default-environment
up to date.
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
instead of polling everytime the environment, we take usage of the global
gd->fdt_blob variable and check it only against NULL.
Variable "dtbaddr" from environment is needed only one time on loading the
devicetree within "load_devicetree()"
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
These methods should be passed a slave device, not a bus. This matches the
old SPI interface. It is important to know which device is claiming the bus
so passing a bus is not that useful.
Reported-by: Haikun Wang <haikun.wang@freescale.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
It is not necessary to write a zero baud rate to the device, and for some
chips this will cause problems. Drop this code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Allow this driver to support boards where the register shift is not 0.
This fixes some compiler warnings which appear in that case.
Signed-off-by: Simon Glass <sjg@chromium.org>
This UART permits different register spacing. To support the debug UART on
devices which have a spacing other than 1 byte, allow the shift value to
be specified.
Signed-off-by: Simon Glass <sjg@chromium.org>
For some files I neglected to add a license. Rectify this:
arch/arm/dts/exynos4210-pinctrl-uboot.dtsi
arch/arm/dts/exynos4x12-pinctrl-uboot.dtsi
arch/arm/dts/exynos5250-pinctrl-uboot.dtsi
arch/arm/dts/exynos54xx-pinctrl-uboot.dtsi
arch/arm/dts/s5pc100-pinctrl.dtsi
arch/arm/dts/s5pc110-pinctrl.dtsi
This file came from Linux and has no license information there, so add a
comment to that effect:
arch/sandbox/include/asm/bitops.h
This file also came from Linux - presumably someone from TI could add the
license:
include/dt-bindings/pinctrl/omap.h
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Ingrid Viitanen <ingrid.viitanen@nokia.com>
We must not clear global_data even in tests, since the ram_buffer (which
is used by malloc()) will also be lost, and subsequent tests will fail.
Zero only the global_data fields that are required for the test to function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Joe Hershberger <joe.hershberger@ni.com>
There are a lot more tests now. To avoid confusion add the updated test
output to the driver model README.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Since a device can have children in the same uclass as itself, we need
to handle unbinding carefully: we must allow that unbinding a device in a
uclass may cause another device in the same uclass to be unbound.
Adjust the code to cope.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Joe Hershberger <joe.hershberger@ni.com>
The functions:
- uclass_find_device_by_name()
- uclass_get_device_by_name()
searches the required device for the exactly given name.
This patch, presice this fact for both function's comments.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
This commit introduces simple tests for functions:
- uclass_find_device_by_name()
- uclass_get_device_by_name()
Tests added by this commit:
- Test: dm_test_uclass_devices_find_by_name: for uclass id: UCLASS_TEST_FDT
* get uclass's devices by uclass_find_first/next_device() each as 'testdev',
* for each returned device, call: uclass_find_device_by_name(),
with previously returned device's name as an argument ('testdev->name').
* for the found device ('founddev') check if:
* founddev != NULL
* testdev == founddev
* testdev->name == founddev->name (by strcmp)
- Test: dm_test_uclass_devices_get_by_name: for uclass id: UCLASS_TEST_FDT
* get uclass's devices by uclass_get_first/next_device() each as 'testdev',
* for each returned device, call: uclass_get_device_by_name(),
with previously returned device's name as an argument ('testdev->name').
* for the found device ('founddev') check if:
* founddev != NULL
* founddev is active
* testdev == founddev
* testdev->name == founddev->name (by strcmp)
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Uclass API provides a few functions for get/find the device.
To provide a complete function set of uclass-internal functions,
for use by the drivers, the function uclass_get_device_tail()
should be non-static.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
This commit extends the driver model device's API by function:
- dev_get_uclass_name()
And this function returns the device's uclass driver name if:
- given dev pointer, is non_NULL
otherwise, the NULL pointer is returned.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
This commit extends the driver model device's API by function:
- dev_get_driver_ops()
And this function returns the device's driver's operations if given:
- dev pointer, is non-NULL
- dev->driver->ops pointer, is non-NULL
in other case the, the NULL pointer is returned.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
This commit extends the driver model uclass's API by function:
- uclass_get_device_by_name()
And this function returns the device if:
- uclass with given ID, exists,
- device with exactly given name(dev->name), exists,
- device probe, doesn't return an error.
The returned device is activated and ready to use.
Note:
This function returns the first device, which name is equal
to the given one. This means, that using this function you must
assume, that the device name is unique in the given uclass's ID
device list.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
This commit extends the driver model uclass's API by function:
- uclass_find_device_by_name()
And this function returns the device if:
- uclass with given ID, exists,
- device with exactly given name(dev->name), exists.
The returned device is not activated - need to be probed before use.
Note:
This function returns the first device, which name is equal
to the given one. This means, that using this function you must
assume, that the device name is unique in the given uclass's ID
device list.
uclass-internal.h: cleanup - move the uclass_find_device_by_seq()
declaration and description, near the other uclass_find*() functions.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
This commit introduces simple tests for functions:
- uclass_find_first_device()
- uclass_find_next_device()
- uclass_first_device()
- uclass_next_device()
Tests added by this commit:
- Test: dm_test_uclass_devices_find:
* call uclass_find_first_device(), then check if: (dev != NULL), (ret == 0)
* for the rest devices, call uclass_find_next_device() and do the same check
- Test: dm_test_uclass_devices_get:
* call uclass_first_device(), then check if:
-- (dev != NULL), (ret == 0), device_active()
* for the rest devices, call uclass_next_device() and do the same check
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
This test introduces new test structure type:dm_test_perdev_uc_pdata.
The structure consists of three int values only. For the test purposes,
three pattern values are defined by enum, starting with TEST_UC_PDATA_INTVAL1.
This commit adds two test cases for uclass platform data:
- Test: dm_test_autobind_uclass_pdata_alloc - this tests if:
* uclass driver sets: .per_device_platdata_auto_alloc_size field
* the devices's: dev->uclass_platdata is non-NULL
- Test: dm_test_autobind_uclass_pdata_valid - this tests:
* if the devices's: dev->uclass_platdata is non-NULL
* the structure of type 'dm_test_perdev_uc_pdata' allocated at address
pointed by dev->uclass_platdata. Each structure field, should be equal
to proper pattern data, starting from .intval1 == TEST_UC_PDATA_INTVAL1.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
This commit adds 'uclass_platdata' field to 'struct udevice', which
can be automatically allocated at bind. The allocation size is defined
in 'struct uclass_driver' as 'per_device_platdata_auto_alloc_size'.
New device's flag is added: DM_FLAG_ALLOC_UCLASS_PDATA, which is used
for memory freeing at device unbind method.
As for other udevice's fields, a complementary function is added:
- dev_get_uclass_platdata()
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
This commit extends the uclass-internal functions by:
- uclass_find_first_device()
- uclass_find_next_device()
For both functions, the returned device is not probed.
After some cleanup, the above functions are called by:
- uclass_first_device()
- uclass_next_device()
for which, the returned device is probed.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Current driver assumes the AHCI is connected to PCI, this is not
true on some SoCs, e.g. LS1021A, which has PCI but the AHCI is
in SoC. This patch will enable embedded AHCI devices on platforms
with PCI.
PCI AHCI devices still can be used by commenting CONFIG_SCSI_AHCI_PLAT
option in head file.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add gzwrite command to write gzip-compressed images to block devices.
Input must be gzip-compressed according to RFC1952, since the crc
and file size in the trailer will be confirmed during operation.
The decompressed file size must be specified on the command line
for images with decompressed sizes >= 4GiB because the trailer
only contains the low 32 bits of the original file size.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Initial filesystem images are generally highly compressible.
Add a routine gzwrite that allows gzip-compressed images to be
written to block devices.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Reviewed-by: Tom Rini <trini@ti.com>
mx6sabresd has four MT41K128M16JT-125 chips. Each memory has 16-bit bus
and 2GiB, so fix the width and density fields accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Move the compilation of file fsl_validate.c in MACRO CONFIG_CMD_ESBC_VALIDATE.
This file should be compiled only when the above MACRO is defined
This caused a break in compilation of iMX platforms when compiling for SECURE_BOOT
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
This patch extracts all baseboard specific defines into a separate config file.
This makes it easier to add other baseboards that use the TQMa6 SoM.
This patch will be used by the upcoming WRU-IV board support which also
uses the TQMa6 SoM.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Markus Niebel <Markus.Niebel@tq-group.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-By: Markus Niebel <Markus.Niebel@tq-group.com>
The LDO_EN is bit 4, not value 4. This is only used on the Ventana boards so
we will change it in the header as the other values there are in terms of
values and not bit numbers.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
This commit combines catching missing memory and calibration data into
one if() block. It further prints pertinent information in determining
why the failure occurred.
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The initial revision of the GW551x does not connect enough signals between
the HDMI receiver and the IMX6 CSI for 16bit capture mode necessary for
yuv422smp capture. Future revisions will, but for the initial rev force it
to yuv422bt656 mode which requires an 8bit video data bus.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The HDMI receiver used on the GW54xx and GW551x has a 16bit video data bus
interconnect between it and the IMX6 CSI. This can be used in two different
modes, each having advantages and disadvantages. Allow the hdmiinfmt env
var to specify which format is desired (yuv422smp or yuv422bt656).
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The GW522x is functionally the same as a GW52xx except for PCIE_RST#
GPIO. Add a DT fixup to change this gpio upon bootup.
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
This adds information about the Gateworks System Controller to the gsc command
such as the firmware version, firmware CRC and status of the GSC watchdog
(if its enabled and if its tripped).
Additionally the 'gsc wd' command can be used to enable or disable the
watchdog with the following usage:
gsc wd enable [30|60]
gsc wd disable
Note that the GSC registers are battery-backed by the GSC coincell so once
eanbled, they remain enabled across power-cycles or until either the GSC
firmware has been updated or FLASH has been re-programmed by the Gateworks
JTAG adapter.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Configure kernel device-tree for display from env var. This is useful
to specify the display present when the device-tree supports multiple
non-detectable display configurations.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Certain older kernels in use by some customers erroneously define a uart3
for GW54xx with a pinmux that conflicts with NAND. This will remove
that node to avoid such conflicts.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Updated 16bit DDR calibration using values obtained from running the
i.MX6 DDR Stress Test tool over a set of boards over full operationg
temperature.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The GW551x-A revision does not have the CSI0_DATA_EN pin connected, therefore
we need to make sure that signal is not muxed to the CSI_DATA_EN signal
internally and do so by steering it to the unused GPIO5_IO20.
We do this so that the kernel device-tree can properly define the signal for
RevB and beyond boards that do have this hooked up properly and require it.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add a new voltage rail added in various -C revision PCB's.
Additionally make VDD_CORE, VDD_SOC, and VDD_IO2 common as all Ventana boards
have those.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Certain OS bootscripts need to know how much memory a board has to adjust
kernel parameters (namely Android). This allows those boards to determine
mem size in MB.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The min/max of each depends not only on board but on CPU. Simplify by removing
this rarely needed and difficult to maintain feature and just display the
rails and their values.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Added support in default boot scripts to find kernel/dtbs on a boot volume
separate from rootfs volume.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The GW551x is a small form factor board based on the IMX6 SoC that includes:
* up to 512MB DDR3 memory
* up to 2GB NAND flash
* 1x miniPCIe socket (with USB)
* HDMI out (micro-HDMI)
* HDMI in (micro-HDMI)
* TTL level I/O (supported by GW16111 breakout board):
* I2C
* 2x UART
* CAN
* 2x DIO (GPIO/PWM)
* USB OTG
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
A board level errata causes the IMX6 watchdog to be unstable on the GW51xx
RevA and RevB boards which can cause the watchdog to trip extremely early
(under 5seconds) under certain operating conditions. Disable the watchdog
node in the device-tree to work around this issue.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Enable the 'i2c edid' command to query and display data from an attached
HDMI monitor of LVDS display with an EDID device.
Example:
Ventana > i2c dev 2 && i2c edid 0x50
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add support for the USB mass storage gadget to enable access to on-board
storage.
Example:
Ventana > ums 0 mmc 0 # provide ums access to the uSD
Ventana > ums 0 usb 0 # provide ums access to the first USB device
Ventana > ums 0 sata 0 # provide ums access to an mSATA device
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The IMX6 Datasheets specifies that when the IMX6 LDO is enabled
(internal Anatop LDO's for VDD_ARM, VDD_SOC, and VDD_xPU) you need to
provide 1350mV on VDD_ARM_IN and VDD_SOC_IN for IMX6Q@1GHz (Automotive)
and 1275mV for IMX6DL@800MHz (Industrial). While we are still about 50mV
shy on the IMX6Q operating at 1GHz we set it to the max we can and leave it
up to the kernel to implement a regulator driver for the LTC3676 and put
the LDO's in bypass mode which allows us to drop the voltages by 125mV
respectively.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The GW52xx has a MUX that can direct front-panel USB OTG to one of the
miniPCIe sockets (for use with a cellular modem for example). Use hwconfig
to steer this.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Gateworks Ventana boards don't all use IMX6 FEC, so lets define default
ethprime based off the first detected device.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
I've encountered issues when using 4k packets through certain switches. For
now disable this and go back to using MTU size packets.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add 'fdt_fixup_display' function to fixup device-tree native-mode property
of display-timings node to select timings for a specific display.
This is useful if a device-tree has configurations for multiple
display timings for undetectable displays.
see kernel Documentation/devicetree/bindings/video/display-timing.txt
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Simon Glass <sjg@chromium.org>
DDR3 has a special Precharge power-down mode: fast-exit vs slow-exit.
In slow-exit mode the DLL is off but in some quiescent state that makes it easy
to turn on again in tXPDLL cycles (about 10tCK) vs the full tDLLK (512tCK).
In fast-exist mode the DLL is maintained such that it is ready again in about
3tCK.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reading the boot mode pins after power-up does not necessarily represent the
boot mode used by the ROM loader. For example the state of a pin may have
changed because a recovery switch which was pressed to enter USB mode is
already released after plugging in USB.
The ROM loader stores the value a fixed address in OCRAM. Use this value
instead of reading the boot map pins.
The GLOBAL_BOOT_MODE_ADDR for i.MX28 is taken from an U-Boot patch for the
MX28EVK:
http://repository.timesys.com/buildsources/u/u-boot/u-boot-2009.08/u-boot-2009.08-mx28-201012211513.patch
Leave the boot mode detection for the i.MX23 untouched. Someone has to test
whether the i.MX ROM loader does also store the boot mode in OCRAM and if the
address match.
This patch superseeds my incorrect patch:
ARM: mxs: get boot mode from OTP
http://patchwork.ozlabs.org/patch/454930/
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
Cc: Stefano Babic <sbabic@denx.de>
Need to check value of spi_setup_slave and spi_setup_slave_fdt.
If their return value 'bus' is NULL, there is no need to pass it
to following spi_flash_probe_tail.
If 'bus' is null, the original function flow is as following:
spi_flash_probe
|->spi_setup_slave
|->spi_probe_bus_tail
|->spi_flash_probe_slave
|->spi_free_slave
Alougth check the pointer in spi_free_slave is ok, checking the return value
of spi_setup_slave and spi_setup_slave_fdt is better.
Before this fix:
"
=> sf probe 0:2
FSL_QSPI: Not a valid cs !
SF: Failed to set up slave
data abort
pc : [<fff66dcc>] lr : [<fff7628c>]
reloc pc : [<87814dcc>] lr : [<8782428c>]
sp : fdf4fcf0 ip : e630396c fp : fe0d0888
r10: fffa2538 r9 : fdf4feb8 r8 : 02625a00
r7 : 00000002 r6 : fff94ec0 r5 : 00000000 r4 : 9355553c
r3 : 1af0593c r2 : cb3fe030 r1 : fff94eb8 r0 : e59ff018
Flags: nZCv IRQs off FIQs off Mode SVC_32
Resetting CPU ...
"
After this fix:
"
=> sf probe 0:2
FSL_QSPI: Not a valid cs !
Failed to initialize SPI flash at 0:2
"
No data abort using this patch.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
On SoCFPGA, using "sf update" with an non-4byte aligned length leads
to a hangup (and reboot via watchdog). This is because of the unaligned
access in the cadence QSPI driver which is hard to prevent since the
data is written into a 4-byte wide FIFO. This patch fixes this problem
by changing the behavior of the last sector write (not sector aligned).
The new code is even simpler and copies the source data into the temp
buffer and now uses the temp buffer to write the complete sector. So
only one SPI sector write is used now instead of 2 in the old version.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Gerlando Falauto <gerlando.falauto@keymile.com>
Cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Cc: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Removed the unnecessary error check from spi_xfer
as the bitlen zero is possible now to deassert the
chip select for which no data is required to be transfered.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Poll both the Read status and Flag status registers
for sucessful erase and program operations for the
Micron devices with E_FSR flag set in params table.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Correct the macros as per insertion of array fast read
command CMD_READ_ARRAY_FAST in spi_read_cmds_array in file
sf_probe.c
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
This patch adds description for NOR flash layout (firmware images)
in the README file for LS2085A platforms.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The Debug Server driver is responsible for loading the Debug
server FW on the Service Processor (Cortex-A5 core) on LS2085A like
SoCs and then polling for the successful initialization of the same.
TOP MEM HIDE is adjusted to ensure the space required by Debug Server
FW is accounted for. MC uses the DDR area which is calculated as:
MC DDR region start = Top of DDR - area reserved by Debug Server FW
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Muram will power off during deepsleep, and the microcode of qe
in muram will be lost, it should be reload when resume.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Muram will power off during deepsleep, and the microcode of qe
in muram will be lost, it should be reload when resume.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Check if USB Erratum A005697 is applicable on BSC913x and
add corresponding property in the device tree via device
tree fixup which is used by linux driver
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
1. LS2085a provides PCIE_LUT_DBG register rather than PCIE_LDBG
to show the link status, so the patch fixes it.
2. Increase the delay time to make sure that link training
has finished.
3. Return invalid value when accessing multi-function device
4. For LS2085a DBI_RO_WR_EN bit is cleared as default, so we
must set this bit before change DBI register value.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The patch uses the common function name ft_pci_setup to replace
ft_pcie_setup, then removes unnecessary pcie_layerscape.h because
all the functions have been declared in common.h.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add following affected SOCs and their personalities for USB
Erratum A007792 :
T1040 Rev 1.1
T1024 Rev 1.0
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Identify soc(s) having dual phy so as to add "utmi_dual" as phy_mode
for all these socs. This is required for supporting deel-sleep feature
in linux for usb driver
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
1. Default environment will be used for secure boot flow
which can't be edited or saved.
2. Command for secure boot is predefined in the default
environment which will run on autoboot (and autoboot is
the only option allowed in case of secure boot) and it
looks like this:
#define CONFIG_SECBOOT \
"setenv bs_hdraddr 0xe8e00000;" \
"esbc_validate $bs_hdraddr;" \
"source $img_addr;" \
"esbc_halt;"
#endif
3. Boot Script can contain esbc_validate commands and bootm command.
Uboot source command used in default secure boot command will
run the bootscript.
4. Command esbc_halt added to ensure either bootm executes
after validation of images or core should just spin.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
On QDS board with DDR4 DIMM, LPUART is used as console
output to verify DCU driver. This patch adds
ls1021aqds_ddr4_nor_lpuart_defconfig for this support.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Freescale LS1021ATWR share some pins. Hwconfig option is used to
allows users to choose the pin functions.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
[York Sun: revised commit message]
Reviewed-by: York Sun <yorksun@freescale.com>
For LS102xA, some workarounds are only used in VER1.0, so silicon
version detection are added for QDS and TWR boards.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
commit aed2fbef5e
"dm: serial: Tidy up the pl01x driver"
caused a regression on (real hardware) PL010 by omitting
to update the line control register when switching baudrate.
Fix this by inlining the missing write to the baud control
register.
Also renaming the set_line_control() function to
pl011_set_line_control() since this function is clearly
PL011-specific, and it won't suffice to call that to
set up line control.
Tested on the Integrator/AP hardware.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
"commit 0d13a0051b2c arm: socfpga: Sync Cyclone V DK PLL configuration"
mistakenly changed CONFIG_HPS_MAINPLLGRP_VCO_NUMER to 39, the correct
value should be 79.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Add a stub s_init function in the board file. The reason why the stub function
is needed is that most of the work is now being done in board_init_f(), there
is no need for the SPL to do anything s_init(). However, since lowlevel_init()
is still branching to s_init(), we need stub function for now, until
lowlevel_init() morphs into s_init().
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
commit "07d30b6c3129 arm: socfpga: Sync Cyclone V DK pinmux configuration"
incorrectly set the muxing for UART0 on the Cyclone V DK.
This fixes it up so UART0 is working again.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
For SoCFGPA, use the common ARMv7 lowlevel_init. Thus, we can delete the
SoCFPGA lowlevel_init.S file.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
These functions will be needed for use by the SPL for enabling the
console and sdram initialization.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
The name "pch_gbe.%x" exceeds the limit of the name in the
'struct eth_device'. Rename it as just "pch_gbe".
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
commit 3c6928fd7b "net: phy: fix warnings with W=1" caused
some PHYs(e.g. CS4315/CS4340) not working. This patch fixes the
warning and make those special PHYs working as well.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
When accessing PHY registers it is often desirable to only update
selected bits, so it is necessary to first read the current value
before writing back an modified value with the relevant bits
updated.
To simplify this and to allow such operations to be incorporated
into simple shell scripts propose adding a 'modify' option to the
existing mii command, which takes a mask indicating the bits to
be updated in addition to a data value containing the new bits,
ie, <updated> = (<data> & <mask>) | (<current> & ~<mask>).
Signed-off-by: Tim <tim.james@macltd.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Jeroen Hofstee <jeroen@myspectrum.nl>
Cc: Tom Rini <trini@konsulko.com>
Cc: Tim <tim.james@macltd.com>
Turn ioaddr into an unsigned long rather than a sized 32-bit variable.
While at it, fix a couple of pointer to integer cast size mismatch
warnings by casting through unsigned long going from pointers to
integers and vice versa.
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Some Realtek Ethernet PHYs, like RTL8211D(G/N) and RTL8211E(G), have
interrupts enabled by default. If the interrupt is not treated later by
the OS and the PHY's interrupt line is enabled and shared with other
interrupts, the system will get an interrupt storm. This patch disables
the interrupt for PHY devices that use one of the current Realtek
Ethernet PHY drivers. Some of Realtek Ethernet PHYs, such as RTL8211B(L)
have the interrupt masked. In this case, the functionality of the PHY
should not be afected since this patch brings INER and INSR registers to
their default values.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
U-Boot on this board grew a long time ago past the 384 KiB that
it reserves for the U-Boot image, before the environment. Thus,
saveenv overwrites the U-Boot image and bricks the board.
I tried to find out when U-Boot grew beyond this point, but there is a
long stretch in the history where this board did not build -- and
AFAICT when it did fit in 384 KiB, it was missing vital features such
as fdt support. Turning off CONFIG_VIDEO was not enough to make it
fit. Thus, I don't think we have any choice other than to move the
environment.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
U-Boot does not have system calls (the services it exposes to
standalone commands use a different mechanism), so the syscall handler
is dead code. It's also broken code, as it assumes it is located at
0xc00 -- while even before the patch to stop relocating exception
vectors to 0, U-Boot had the syscall at 0x900.
The critical and machine check return paths are never called -- the
regular exception return path is used instead, which works because
xSRR0/1 have already been saved and can be restored via the regular
SRR0/1 (we don't care too much in U-Boot about taking a critical/mcheck
inside another exception prolog/epilog).
Also remove a few other small unused functions.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Booke does not require exception vectors to be located at address zero.
U-Boot was doing so anyway, simply because that's how it had been done
on other PPC. The downside of this is that once the OS is loaded to
address zero, the exception vectors have been overwritten -- which
makes it difficult to diagnose a crash that happens after that point.
The IVOR setup and trap entry code is simplified somewhat as a result.
Also, there is no longer a need to align individual exceptions on 0x100
byte boundaries.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Support SODIMM D3XP12081XL10AA 1866MT/s on T2080RDB.
Enable CONFIG_CMD_MEMTEST as well.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Now cortina driver uses macro CONFIG_SYS_CORTINA_FW_IN_NOR
to define that firmware of cortina driver is stored in the
nor flash.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The fuse status register provides the values from on-chip
voltage ID efuses programmed at the factory.
These values define the voltage requirements for
the chip. u-boot reads FUSESR and translates the values
into the appropriate commands to set the voltage output
value of an external voltage regulator.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
QEMU 2.3 changes the address layout of the CCSR map in the PV ppce500 machine
to reside in higher address space.
Unfortunately, this exposed a glitch in u-boot for ppce500: While providing
a function to dynamically evaluate the CCSR region's position in physical
address space, we never used it. Plus we forgot to support 64bit physical
addresses.
This patch fixes that mishap, making u-boot work fine with latest QEMU again.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
According to the MPC8555/MPC8541 reference manual the SS_EN (source
synchronous enable) bit in the DDR_SDRAM_CLK_CNLT register must be set
during initialization.
>From section 9.4.1.8 of that manual:
Source synchronous enable. This bit field must be set during
initialization. See Section 9.6.1, "DDR SDRAM Initialization
Sequence," details.
0 - Reserved
1 - The address and command are sent to the DDR SDRAMs source
synchronously.
In addition, Freescale application note AN2805 is also very clear that
this bit must be set.
This patch reverts a change introduced by commit
457caecdbc.
Testing Done:
Compiled targets CONFIG_TARGET_MPC8555CDS and CONFIG_TARGET_MPC8541CDS
and inspected the generated assembly code to verify the SS_EN bit was being
set. There is one extra instruction emitted:
fff9b774: 65 29 80 00 oris r9,r9,32768
Compiled the CONFIG_TARGET_MPC8548CDS target and verified that no
additional instructions were emitted related to this patch.
Booted an image on a MPC8541 based board successfully.
Signed-off-by: Curt Brune <curt@cumulusnetworks.com>
Reviewed-by: York Sun <yorksun@freescale.com>
the ldb clock can be setup in board code (for example set through PLL5).
Update the ldb_clock rate also through board code.
This should be removed, if a clock framework is availiable.
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Eric Nelson <eric.nelson@boundarydevices.com>
make the ldb_clock configurable through the new define
CONFIG_SYS_LDB_CLOCK. This is needed as the ldb clock is not
always 650000000, for example on the aristainetos2 board,
where the ldb clock derives from PLL5 clock.
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Eric Nelson <eric.nelson@boundarydevices.com>
Make the sandbox setup more generic/examplary by including
config_distro_defaults.h and config_distro_bootcmd.h.
Among other things this makes it easy to test whether images will boot
though with the standard distro bootcmds by running e.g:
u-boot -c 'host bind 0 myimage.img ; boot'
By default there are 2 target host devices to emulate device with
multiple storage devices (e.g. internal ("host 0") and external
("host 1") and verify that the prioritization and fallbacks do work
correctly.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Define default PXE client architecture identifiers for IA32 (0x0 aka
Intel x86PC) and Intel x86-64 (0x9 aka EFI x86-64).
This prepares for usage for config_distro_defaults in the sandbox
architecture
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Properly map memory through map_sysmem so that pxe can be used from the
sandbox.
Tested in sandbox as well as on jetson-tk1, odroid-xu3, snow as peach-pi
boards
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Define the common shared block environment for the host interface in
preperation for the sandbox build to use config_distro_bootcmd.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
A common pattern to check if a certain device exists (e.g. in
config_distro_bootcmd) is to use: <interface> dev [device]
Implement host dev [device] so this pattern can be used for sandbox host
devices.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
As suggested by Simon Glass, rename the sb command to host but keep the
old sb command as an alias
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Add dummy bootz_setup implementation allowing the u-boot sandbox to
run bootz. This recognizes both ARM and x86 zImages to validate a
valid zImage was loaded.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Follow the convention of other architectures and move the platform
specific linux bootm code into sandbox/lib/bootm.c.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Only do sandbox filesystem access when using the hostfs device
interface, rather then falling back to it in all cases. This prevents
confusion situations due to the fallback being taken rather then an
unsupported error being raised.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
The help text for -V says we will pass V=1 but all it really did was not
pass in -s. Change the logic to pass make V=1 with given to buildman -V or
-s to make otherwise.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Simon Glass <sjg@chromium.org>
When told to keep outputs, be much more liberal in what files we keep.
In addition to adding 'MLO', keep anything that matches u-boot-spl.* (so
that we keep the map file as well) and anything we generate about
'u-boot itself. A large number of bootable formats now match this and
thus it's easier to build many targets and then boot them afterwards
using buildman.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Simon Glass <sjg@chromium.org>
It is useful to be able to see CONFIG changes made by commits. Add this
feature to buildman using the -K flag so that all CONFIG changes are
reported.
The CONFIG options exist in a number of files. Each is reported
individually as well as a summary that covers all files. The output
shows three parts: green for additions, red for removals and yellow for
changes.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present buildman tries to detect an aborted build and doesn't record a
result in that case. This is to make sure that an abort (e.g. with Ctrl-C)
does not mark the build as done. Without this option, buildman would never
retry the build unless -f/-F are provided. The effect is that aborting the
build creates 'fake errors' on whatever builds buildman happens to be
working on at the time.
Unfortunately the current test is not reliable and this detection can
trigger if a required toolchain tool is missing. In this case the toolchain
problem is never reported.
Adjust the logic to continue processing the build result, mark the build as
done (and failed), but with a return code which indicates that it should be
retried.
The correct fix is to fully and correctly detect an aborted build, quit
buildman immediately and not write any partial build results in this case.
Unfortunately this is currently beyond my powers and is left as an exercise
for the reader (and patches are welcome).
Signed-off-by: Simon Glass <sjg@chromium.org>
At present CONFIG options are split across Kconfig and board config headers
files. Also we have multiple files containing these CONFIG options.
In order to see exactly what is being used for building, create a .cfg
file which holds these options as reported by the C preprocessor.
Signed-off-by: Simon Glass <sjg@chromium.org>
Don't store it in a u32.
Don't dereference the bus address as if it were a virtual address
(fixes 284231e49a ("ahci: Support splitting of read transactions
into multiple chunks")).
Fixes crash on boot in MPC8641HPCN_36BIT target.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Vadim Bendebury <vbendeb@chromium.org>
Acked-by: York Sun <yorksun@freescale.com>
Adjust the Ethernet initialisation code to support driver model.
It is no-longer necessary to call designware_initialize(). The device will
be probed when it is used. The PHY type and GMAC base will come from the
device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add driver model support to the designware driver. This reuses most of the
existing code except for some duplication in the probe() method.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Adjust the error handling to use errno.h instead of returning -1. Change
leaf functions to pass in the arguments they require rather than struct
eth_device. Apart from simplifying the code it makes is easier to reuse
these functions for driver model, since mostly they actually only use
struct dw_eth_priv (which we can keep).
Create a stub for each Ethernet operation function. This will allow use to
share code with the driver model versions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When driver model is used for Ethernet a few functions are passed a udevice
instead of an eth_device. Also add a function to find a PHY type given its
name. This will be used to decode the device tree node.
Finally, put a phy_interface field in struct eth_pdata since this is an
important part of the platform data for Ethernet.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
At present even with driver model is used there is still much manual init
of related devices: PHY, environment and board init. Until these requirements
are dealt with in another way we need to keep them around.
Break out the init portion of the legacy eth_initialize() into a separate
function and call it from both the legacy and driver model eth_initialize()
functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Since we will use these bindings on sunxi, bring them in from Linux
4.0-rc1.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Move this to Kconfig and clean up board config files that use it. Also
rename it to CONFIG_ETH_DESIGNWARE to fit with the naming that exists
in drivers/net/Kconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
Version 1:
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
We currently have Linksprite_pcDuino3 and Linksprite_pcDuino3_fdt. Drop the
former in favour of the latter.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
More net features enabled and supported on sandbox to allow more testing
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
When SNTP is enabled and DATE is not, to_tm() is not built in. It could
be defined when TIMESTAMP is defined, so check for that.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit fixes incorrect DHCP/BOOTP packet layout caused by
'ulong' type size difference on 64 and 32-bit architectures.
It also renames NetReadLong()/NetCopyLong() to
net_read_u32/net_copy_u32() accordingly.
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
Signed-off-by: Sergey Temerkhanov <s.temerkhanov@gmail.com>
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Finish eliminating CamelCase from net.c and other failures
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
There were still a few remaining complains in the legacy eth_device
definition that hadn't been addressed.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
There were still a few failures in net/eth.c, especially in the legacy
part of the code.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
A few new rules in checkpatch.pl since linklocal.c was added.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Make a thorough pass through all variables and function names contained
within common/cmd_net.c and remove CamelCase and improve naming.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Make a thorough pass through all variables and function names contained
within netconsole.c and remove CamelCase and improve naming.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Make a thorough pass through all variables and function names contained
within dns.c and remove CamelCase and improve naming.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Make a thorough pass through all variables and function names contained
within cdp.c and remove CamelCase and improve naming.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Make a thorough pass through all variables and function names contained
within ping.c and remove CamelCase and improve naming.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Make a thorough pass through all variables and function names contained
within sntp.c and remove CamelCase and improve naming.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Make a thorough pass through all variables and function names contained
within rarp.c and remove CamelCase and improve naming.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Make a thorough pass through all variables and function names contained
within nfs.c and remove CamelCase and improve naming.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Make a thorough pass through all variables and function names contained
within bootp.c and remove CamelCase and improve naming.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Make a thorough pass through all variables and function names contained
within arp and remove CamelCase and improve naming.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Make a thorough pass through all variables and function names contained
within tftp and remove CamelCase and improve naming.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Update the naming convention used in the network stack functions and
variables that Ethernet drivers use to interact with it.
This cleans up the temporary hacks that were added to this interface
along with the DM support.
This patch has a few remaining checkpatch.pl failures that would be out
of the scope of this patch to fix (drivers that are in gross violation
of checkpatch.pl).
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
This patch cleans up the names of internal packet buffer names that are
used within the network stack and the functions that use them.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Use "_ethaddr" at the end of variables and drop CamelCase.
Make constant values actually 'const'.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Remove CamelCase variable naming.
Move the definition to the same compilation unit as the primary use.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
The variables around the bootfile were inconsistent and used CamelCase.
Update them to make the code more readable.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
This patch is simply clean-up to make the IPv4 type that is used match
what Linux uses. It also attempts to move all variables that are IP
addresses use good naming instead of CamelCase. No functional change.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
All the Zynq boards have switch to Driver Model.
"select DM" is better than default value in each defconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
All the UniPhier boards have switch to Driver Model.
"select DM" is better than default value in each defconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
As mentioned in the previous commit, adding default values in each
Kconfig causes problems because it does not co-exist with the
"depends on" syntax. (Please note this is not a bug of Kconfig.)
We should not do so unless we have a special reason. Actually,
for CONFIG_DM*, we have no good reason to do so.
Generally, CONFIG_DM is not a user-configurable option. Once we
convert a driver into Driver Model, the board only works with Driver
Model, i.e. CONFIG_DM must be always enabled for that board.
So, using "select DM" is more suitable rather than allowing users to
modify it. Another good thing is, Kconfig warns unmet dependencies
for "select" syntax, so we easily notice bugs.
Actually, CONFIG_DM and other related options have been added
without consistency: some into arch/*/Kconfig, some into
board/*/Kconfig, and some into configs/*_defconfig.
This commit prefers "select" and cleans up the following issues.
[1] Never use "CONFIG_DM=n" in defconfig files
It is really rare to add "CONFIG_FOO=n" to disable CONFIG options.
It is more common to use "# CONFIG_FOO is not set". But here, we
do not even have to do it.
Less than half of OMAP3 boards have been converted to Driver Model.
Adding the default values to arch/arm/cpu/armv7/omap3/Kconfig is
weird. Instead, add "select DM" only to appropriate boards, which
eventually eliminates "CONFIG_DM=n", etc.
[2] Delete redundant CONFIGs
Sandbox sets CONFIG_DM in arch/sandbox/Kconfig and defines it again
in configs/sandbox_defconfig.
Likewise, OMAP3 sets CONFIG_DM arch/arm/cpu/armv7/omap3/Kconfig and
defines it also in omap3_beagle_defconfig and devkit8000_defconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
CONFIG_SPI does not exist in Kconfig in the first place, so the
dependency "depends on DM && SPI" is never met, i.e., DM_SPI_FLASH
can never be enabled (unless you ignore the dependency in an illegal
way. See below.)
Actually, some defconfigs such as socfpga_*_defconfig define
CONFIG_DM_SPI_FLASH=y, but it never appears in the .config file
because of this wrong dependency.
On the other hand, all the Tegra boards enable DM_SPI_FLASH because
config DM_SPI_FLASH
default y
silently ignores the dependency.
Unfortunately, this style of CONFIG definition is abused everywhere
in U-Boot, so we easily miss such a wrong dependency.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add some documentation describing how USB is implemented with USB. This
might make things easier for people to understand.
Signed-off-by: Simon Glass <sjg@chromium.org>
This adds a simple test for probing and a functional test using the flash
stick emulator, which tests a large chunk of the USB stack.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
As well as running all tests, it is useful to be able to run a selected test.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Enable USB emulation and associated features so that USB can be used in
sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Add a few more shifts/masks to make it easier to decode a pipe value (rather
than just building it). We need this for USB device emulation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
This is useful for creating lists of descriptors, and is better than using
void * for this purpose.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Since we can support both controllers now, enable this in the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Convert Exynos boards over to use driver model for USB. This does not remove
any unnecessary code so far.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Add driver model support in the XHCI support code so that it can be used by
XHCI USB drivers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Since driver model will want to use most of the same code for XHCI init
and uninit, put it in a separate function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
This function should not be delving into struct usb_device. Pass in the
parameters it needs directly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
This function should not be delving into struct usb_device. Pass in the
parameters it needs directly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Rather than getting this directly from struct usb_device, call a function
to obtain it. This will make it possible for driver model to provide it
another way.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
We want to use mostly the same init and uninit code for driver model, so move
the common part into two functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Try to return useful error numbers where possible. Also avoid swallowing
an error number when it is returned by a called function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
This variable is a bit of a hack. We can obtain the same information from
the normal device config. This will fit better with driver model, where
global variables are best avoided.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Add support for scanning USB etghernet devices with driver model. This mostly
involves scanning all buses since device numbering is not unique across
buses.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
These allow basic testing of the USB functionality within sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
This driver supports using emulation devices to provide a USB bus within
sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
All USB controllers need a root hub. Add a sandbox emulation for this so
that we can add USB devices to sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
This emulator supports USB enumeration and allows a local file to be provided
as the contents of the emulated flash stick. U-Boot can then use the file as
it would a normal device, with all access passing through the usb_stor layer
and the USB stack.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
These devices must have their addresses removed ready for the next USB
bus enumeration. Add this logic to usb_stop().
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
With sandbox we want to be able to emulate USB devices so that we can test
the USB stack. Add a uclass to support this. It implements the same
operations as a normal USB device driver, but in this case passes them on
to an emulation driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
This is needed for sandbox USB device emulation, so move it to a place
where it can be found by things other than gadgets.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
These are needed to enable the USB bus (although not sufficient since it
still does not work).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Allow USB keyboards to work with driver model. The main difference is that
we can have multiple buses (each with its own device numbering) and each
bus must be scanned.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Before adding driver model support, split out code from this over-long
function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Some controllers support OTG (on-the-go) where they can operate as either
host or device. The gadget layer in U-Boot supports this.
While this layer does not interact with driver model, we can provide a
function which sets up the controller in the correct way. This way the code
at least builds (although it likely will not work).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
At present USB devices with no driver model driver cannot be seen in the
device list, and we fail to set them up correctly. This means they cannot
be used.
While having real drivers that support driver model for all USB devices
is the eventual goal, we are not there yet.
As a stop-gap, add a generic USB driver which is bound when we do not have
a real driver. This allows the device to be set up and shown on the bus.
It also allows ad-hoc code (such as usb_ether) to find these devices and
set them up.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
USB devices in U-Boot are currently probed only after all devices have
been enumerated. Each type of device is probed by custom code, e.g.:
- USB storage
- Keyboard
- Ethernet
With driver model this approach doesn't work very well. We could build
a picture of the bus and then go back and add the devices later, but
this means that the data structures are incomplete for quite a while.
It also does not follow the model of being able to bind a device when we
discover it.
We would prefer to have devices automatically be bound as the device is
enumerated. This allows us to attach drivers to particular USB classes
or product/vendor IDs. This is the method used by Linux.
Add the required #defines from Linux, a way of declaring a USB driver and
the logic to locate the correct driver given the USB device's descriptors.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Add a way for EHCI controller drivers to support driver model. Drivers can
call ehci_register() to register themselves in their probe() methods.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
The index cannot be used with driver model, and isn't needed anyway. Change
the parameter to a pointer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
These are a pain with driver model because we might have different EHCI
drivers which want to implement them differently. Now that they use
consistent function signatures, we can in good conscience move them to
a struct.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Fix non-driver-model EHCI to set up the EHCI operations correctly:
Signed-off-by: Tom Rini <trini@konsulko.com>
Move the bulk of the code in usb_lowlevel_init() into a separate function
which will also be used by driver model. Keep the CONFIG options out of
this function by providing a tweak flag for Faraday. We need to avoid using
CONFIG options in driver model code where possible, since it makes it
impossible to use multiple controllers in that code where they have
different options.
The CONFIG_EHCI_HCD_INIT_AFTER_RESET option is also kept out of the
common init function. With driver model the controller will be able to
perform this extra init itself after registering with the EHCI layer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
With driver model we want to remove the controller pointer in struct udevice
and use driver model data structures instead. To prepare for this, move
access to this field to a function which can provide a different
implementation for driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Adjust this function so that it is passed an EHCI controller pointer so that
implementations can look up their controller. This makes the weak functions
use a consistent API.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Adjust this function so that it is passed an EHCI controller pointer so that
implementations can look up their controller. This makes the weak functions
use a consistent API.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
We don't need this anymore, so adjust the code to avoid using it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Adjust this function so that it is passed an EHCI controller pointer so that
implementations can look up their controller.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
At present the tegra driver uses a separate pointer to know which controller
type is in use. This works because only one controller type is used at a
time.
With driver model we want to make the controller state hermetic in the sense
that it is not necessary to look elsewhere to know the controller type. This
will permit a controller to implement the EHCI weak functions without
reference to global data structures.
To achieve this, define an enum for the controller type and store it with
the information on each EHCI controller.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Add a private data pointer that clients of EHCI can use to access their
private information. This establishes a link between struct ehci_ctrl and
its associated controller data structure.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Adjust this function so that it is passed an EHCI controller pointer so that
implementations can look up their controller.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Put these at the top of the file so they are in one place. Also add function
prototypes to the header file to avoid call site mismatches.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Add support for scanning USB storage devices with driver model. This mostly
involves adding a USB device ID for storage devices.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
The usb_stor_scan() function is quite long, so split out the code that scans
each device into its own function. Also, rather than setting up the block
device list once at the start, set it up as each device is scanned. This
makes it possible to use this code from driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
With a few tweaks we can compile this code with sandbox and enable testing
of the USB storage layer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
The for() loop is not needed since the value is immediately accessible.
Use this instead to simplify the code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
This function assumes that unsigned long is 32-bits wide, but it is not
on 64-bit machines. Use the correct type, and add a few debug() lines also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
These are better off in a header file so they can be used by other code (e.g.
the sandbox USB storage emulator).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Adjust the existing hub code to support driver model, and add a USB driver
for hubs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Split out the hub detection logic so it can be used by driver model. Also
adjust the code to return errors correctly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Add the required #ifdefs and remove unwanted data structures so that the
USB uclass will be able to use this file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
This function now calls usb_setup_device() to set up the device and
usb_hub_probe() to check if it is a hub. The XHCI special case is now a
parameter to usb_setup_device(). The latter will be used by the USB uclass
when it is added, since it does not rely on any CONFIGs or legacy data
structures.
Signed-off-by: Simon Glass <sjg@chromium.org>
Bug-fixes for descriptor reading and usb_new_device() return value
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-by: Tom Rini <trini@konsulko.com>
Move the code that sets up the device with a new address into its own
function, usb_prepare_device().
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
usb_new_device() is far too long and does far too much. As a first step, move
the code that does initial setup and reads a descriptor into its own function
called usb_setup_descriptor().
For XHCI the init order is different - we set up the device but don't
actually read the descriptor until after we set an address. Support this
option as a parameter to usb_setup_descriptor().
Avoid changing this torturous code more than necessary to make it easy to
review.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Move the port reset code into its own function. Rename usb_hub_reset() to
indicate that is is now a legacy function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Adjust this command to work with the new driver model uclass. It needs to
iterate through multiple independent controllers to find hubs, and work
through their children recursively in a different way. Otherwise the
functionality is much the same.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
This function returns NULL on error at present. Adjust it so that we can
return a real error, as is needed with driver model. Also improve the
error handling in its caller, usb_hub_port_connect_change(), and adjust
the code order to prepare for driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Use 'udev' instead of 'dev' in a few places, reserving 'dev' for driver
model's struct udevice. Also adjust the code in a few minor ways to make
it easier to plumb in driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Add a uclass that can represent a USB controller. For now we do not create
devices for things attached to the controller. This will be added later.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
This has a prototype but no implementation. It returns the global GPIO number
given a gpio_desc. It is useful for debugging in some cases.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Add some utility functions to check for children and for the last sibling in
a device's parent.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
The uclass pre-probe functions may end up calling back into the device in
some circumstances. This can fail if recursion takes place. Adjust the
ordering so that we mark the device as active early, then retract this
later if needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
The existing get_get_of_data() function provides access to both the driver's
compatible string and its driver data. However only the latter is actually
useful. Update the interface to reflect this and fix up existing users.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
The driver is not modified by driver model, so update driver_bind() to
recognise that.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Some driver want to put DMA buffers in their private data. Add a flag
to tell driver model to align driver-private data to a cache boundary so
that DMA will work correctly in this case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Once declared, you cannot access a linker_list entry since you do not have
a symbol name for it. Add llsym() macro to provide this. This avoids
searching for the symbol at run-time based on name.
An example usage is to declare a driver with U_BOOT_DRIVER(), then obtain
a pointer to that driver later.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Some drivers need a chance to manage their receive buffers after the
packet has been handled by the network stack. Add an operation that
will allow the driver to be called in that case.
Reported-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Tested-on: pcduino3
Add QSPI controller dts node in ls1021a.dtsi.
Add QSPI slave device dts node in ls1021a-twr.dts and ls1021a-qds.dts.
Signed-off-by: Haikun Wang <Haikun.Wang@freescale.com>
Acked-by: Simon Glass <sjg@chromium.org>
Update DSPI controller node in ls1021a.dtsi.
Update flash device node in ls1021a-qds.dts.
Ls1021a-twr board doesn't support DSPI, so remove DSPI node
in ls1021a-twr.dts.
Signed-off-by: Haikun Wang <Haikun.Wang@freescale.com>
Acked-by: Simon Glass <sjg@chromium.org>
Change address_cells and size_cells of root node and 'soc' node
from 2 to 1.
We backport ls1021a device tree source files from kernel to u-boot.
Kernel files set address_cells and size_cells to 2 in order to access
more than 4GB space.
But we don't have this requirement now and u-boot fdtdec_get_xxx interfaces
can't support property whose size is 'u64' completely.
So make this change.
Signed-off-by: Haikun Wang <Haikun.Wang@freescale.com>
Acked-by: Simon Glass <sjg@chromium.org>
Bring in required device tree files for ls1021a from Linux.
These are initially unchanged and have a number of pieces not needed by U-Boot.
Signed-off-by: Haikun Wang <Haikun.Wang@freescale.com>
Acked-by: Simon Glass <sjg@chromium.org>
Backport of kernel commits:
7c14f6c719de092d69c81877786e83ce7ae1a860
35faad2a1563b3d4dc983a82ac41033fe053870c
Signed-off-by: Haikun Wang <Haikun.Wang@freescale.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit adds driver model support to software emulated i2c bus driver.
This driver supports kernel-style device tree bindings. Fdt properties in use:
- compatible - "i2c-gpio"
- gpios - data and clock GPIO pin phandles
- delay-us - micro seconds delay between GPIOs toggle operations,
which is 1/4 of I2C speed clock period.
Added:
- Config: CONFIG_DM_I2C_GPIO
- File: drivers/i2c/i2c-gpio.c
- File: doc/device-tree-bindings/i2c/i2c-gpio.txt
Driver base code is taken from: drivers/i2c/soft-i2c.c, changes:
- use "i2c-gpio" naming
- update comments style
- move preprocesor macros into functions
- add device tree support
- add driver model i2c support
- code cleanup,
- add Kconfig entry
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Added braces in i2c_gpio_xfer() to fix style nit:
Signed-off-by: Simon Glass <sjg@chromium.org>
The function gpio_request_list_by_name_nodev() returned -ENOSPC error,
when the loop count was greater than requested count. This was wrong,
because function should return the requested gpio count, when meets
the call request without errors. Now, the loop ends on requested
max_count.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
This code appears to be missing a piece that is needed on some keyboards
to enable the keyboard. Add this in.
This makes the keyboard work correctly on chromebook_link.
Signed-off-by: Simon Glass <sjg@chromium.org>
The U-Boot device trees are slightly different in a few places. Adjust them
to remove most of the differences. Note that U-Boot does not support the
concept of interrupts as distinct from GPIOs, so this difference remains.
For sandbox, use the same keyboard file as for ARM boards and drop the
host emulation bus which seems redundant.
Signed-off-by: Simon Glass <sjg@chromium.org>
This command is supposed to reinit the device. At present with driver
model is does nothing. Implement this feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
The PCH (Platform Controller Hub) is on the PCI bus, so show it as such.
The LPC (Low Pin Count) and SPI bus are inside the PCH, so put these in the
right place also.
Rename the compatible strings to be more descriptive since this board is the
only user. Once we are using driver model fully on x86, these will be
dropped.
Signed-off-by: Simon Glass <sjg@chromium.org>
On x86 systems this device is commonly used to provide legacy port access.
It is sort-of a replacement for the old ISA bus.
Add a uclass for this, and allow it to have child devices.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a simple uclass for this chip which is often found in x86 systems
where the CPU is a separate device.
The device can have children, so make it scan the device tree for these.
Signed-off-by: Simon Glass <sjg@chromium.org>
Convert this driver over to use driver model. Since all x86 platforms use
it, move x86 to use driver model for SPI and SPI flash. Adjust all dependent
code and remove the old x86 spi_init() function.
Note that this does not make full use of the new PCI uclass as yet. We still
scan the bus looking for the device. It should move to finding its details
in the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Permit use of a udevice to talk to SPI flash. Ultimately we would like
to retire the use of 'struct spi_flash' for this purpose, so create the
new API for those who want to move to it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Take a pass at plumbing errors through to the users of the network stack
Currently only the start() function errors will be returned from
NetLoop(). recv() tends not to have errors, so that is likely not worth
adding. send() certainly can return errors, but this patch does not
attempt to plumb them yet. halt() is not expected to error.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The 'lo' interface on Linux doesn't support thinks like ARP or
link-layer access like we use to talk to a normal network interface.
A higher-level network API must be used to access localhost.
As written, this interface is limited to not supporting ICMP since the
API doesn't allow the socket to be opened for all IP traffic and be able
to receive at the same time. UDP is far more useful to test with, so it
was selected over ICMP. Ping won't work, but things like TFTP should
work.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Implement a bridge between U-Boot's network stack and Linux's raw packet
API allowing the sandbox to send and receive packets using the host
machine's network interface.
This raw Ethernet API requires elevated privileges. You can either run
as root, or you can add the capability needed like so:
sudo /sbin/setcap "CAP_NET_RAW+ep" /path/to/u-boot
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The effect of the "netretry" env var was recently changed. This test
checks that behavior.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This is needed to test the netretry functionality (make the command fail
on a sandbox eth device).
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Make sure that the ethrotate behavior occurs as expected.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The ethprime env var is used to indicate the starting device if none is
specified in ethact. Also support aliases specified in the ethprime var.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Allow network devices to be referred to as "eth0" instead of
"eth@12345678" when specified in ethact.
Add tests to verify this behavior.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a test for the eth uclass using the sandbox eth driver. Verify basic
functionality of the network stack / eth uclass by exercising the ping
function.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The sandbox driver will now generate response traffic to exercise the
ping command even when no network exists. This allows the basic data
pathways of the DM to be tested.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add basic network support to sandbox which includes a network driver.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Stop forcing drivers to call net_process_received_packet() - formerly
called NetReceive(). Now the uclass will handle calling the driver for
each packet until the driver errors or has nothing to return. The uclass
will then pass the good packets off to the network stack by calling
net_process_received_packet().
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Take the opportunity to enforce better names on newly written or
retrofitted Ethernet drivers.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The return codes in common/cmd_net.c had a number of inconsistencies.
Update them to all use the enum from command.h
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Previously the net functions would access memory assuming physmem did
not need to be mapped. In sandbox, that's not the case.
Now we map the physmem specified by the user in loadaddr to the buffer
that represents that space.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
netretry previously would only retry in one specific case (your MAC
address is not set) and no other. This is basically useless. In the DM
implementation for eth it turns this into a completely useless case
since an un-configured MAC address results in not even entering the
NetLoop. The behavior is now changed to retry any failed command
(rotating through the eth adapters if ethrotate != no).
It also defaulted to retry forever. It is now changed to default to not
retry
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This value is not used by the network stack and is available in the
global data, so stop passing it around. For the one legacy function
that still expects it (init op on old Ethernet drivers) pass in the
global pointer version directly to avoid changing that interface.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reported-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
(Trival fix to remove an unneeded variable declaration in 4xx_enet.c)
Many functions returned -1 previously. Change them to return appropriate error
codes.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reported-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move some things around and organize things so that the driver model
implementation will fit in more easily.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Many of the functions in net.h were preceded extern needlessly. Removing
them to limit the number of checkpatch.pl complaints.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Make it clear that the helper is checking the addr, not setting it.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The current implementation exposes the eth_device struct to code that
needs to access the MAC address. Add a wrapper function for this to
abstract away the pointer for this operation.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In the case where the arch defines a custom map_sysmem(), make sure that
including just mapmem.h is sufficient to have these functions as they
are when the arch does not override it.
Also split the non-arch specific functions out of common.h
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move chromebook_link over to driver model for PCI.
This involves:
- adding a uclass for platform controller hub
- removing most of the existing PCI driver
- adjusting how CPU init works to use driver model instead
- rename the lpc compatible string (it will be removed later)
This does not really take advantage of driver model fully, but it does work.
Furture work will improve the code structure to remove many of the explicit
calls to init the board.
Signed-off-by: Simon Glass <sjg@chromium.org>
This device sits on the sandbox PCI bus and provides a case-swapping
service for sandbox. It illustrates the use of both PCI I/O and PCI
memory accesses.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sometimes, for example if the display is mounted in portrait mode or even if it
is mounted landscape but rotated by 180 degrees, we need to rotate our content
of the display respectively the framebuffer, so that user can read the messages
which are printed out.
For this we introduce the feature called "CONFIG_LCD_ROTATION", this may be
defined in the board-configuration if needed. After this the lcd_console will
be initialized with a given rotation from "vl_rot" out of "vidinfo_t" which is
provided by the board specific code.
If CONFIG_LCD_ROTATION is not defined, the console will be initialized with
0 degrees rotation.
Signed-off-by: Hannes Petermaier <hannes.petermaier@br-automation.com>
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
[agust: fixed 'struct vidinfo' has no member named 'vl_rot' errors]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
For coming implementation of lcd_console rotation, we will need some more
variables for holding information about framebuffer size, rotation, ...
For better readability we catch all them into a common structure.
Signed-off-by: Hannes Petermaier <hannes.petermaier@br-automation.com>
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
the capability of drawing some *str with count from lcd_drawchars is unnary.
It is always called from lcd_putc_xy with one character of and count = 1.
So we simply rename lcd_drawchars into lcd_putc_xy and remove the loops inside.
Signed-off-by: Hannes Petermaier <hannes.petermaier@br-automation.com>
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
Since sandbox does not have real devices (unless it borrows those from the
host) it must use emulations. Provide a uclass which permits PCI operations
to be passed through to an emulation device.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add the required header information, device tree nodes and I/O accessor
functions to support PCI on sandbox. All devices are emulated by drivers
which can be added as required for testing or development.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a uclass for PCI controllers and a generic one for PCI devices. Adjust
the 'pci' command and the existing PCI support to work with this new uclass.
Keep most of the compatibility code in a separate file so that it can be
removed one day.
TODO: Add more header file comments to the new parts of pci.h
Signed-off-by: Simon Glass <sjg@chromium.org>
Driver model will share many functions with the existing PCI implementation.
Move these into their own file to avoid duplication and confusion.
Signed-off-by: Simon Glass <sjg@chromium.org>
Both of these values are useful for understanding what is going on, so show
them both.
The requested number comes from a device tree alias. The allocated one is
set up when the device is activated, and is unique throughout the uclass.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some uclasses want to set up a device before it is probed. Add a method
for this.
An example is with PCI, where a PCI uclass wants to set up its private
data for later use. This allows the device's uclass() method to make calls
whcih use that data (for example, read PCI memory regions from device
tree, set up bus numbers).
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the device is not active when the probe() method is called. But
some probe() methods want to set up the device and this can involve
accessing it through normal methods. For example a PCI bus may wish to
set up its PCI parameters using calls to pci_hose_write_config_dword() and
similar.
At present this does not work because every such call within the probe()
method sees that the device is not active and attempts to probe it.
Already we mark the device as probed before calling the uclass post_probe()
method. This is a subtle change but I believe the new approach is better.
Since the scope of the change is only the probe() method and all its callees
it should still be within the control of the board author.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a convenience function to access the private data that a uclass stores
for each of its devices. Convert over most existing uses for consistency
and to provide an example for others.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function returns -ENOENT when the property is missing (which the caller
might forgive) and also when the property is present but incorrectly
formatted (which many callers would like to report).
Update the error return value to allow these different situations to be
distinguished.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present we do more in this function than we should. Split out the
post-driver-model part into a separate function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Since driver model is set up after arch_cpu_init(), that function cannot
use drivers. Add a new arch_cpu_init_dm() function which is called
immediately after driver model is ready, and can reference devices.
This can be used to probe essential devices for the CPU.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
These functions currently use a generic name, but they are for x86 only.
This may introduce confusion and prevents U-Boot from using these names
more widely.
In fact it should be possible to remove these at some point and use
generic functions, but for now, rename them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This function is missing a prototype but is more widey useful. Add it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
We should have a size value for these. Add one in each case. This will
be needed for PCI.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Support running U-Boot as a coreboot payload. Tested peripherals include:
- Video (HDMI and DisplayPort)
- SATA disk
- Gigabit Ethernet
- SPI flash
USB3 does not work. This may be a problem with the USB3 PCI driver or
something in the USB3 stack and has not been investigated So far this is
disabled. The SD card slot also does not work.
For video, coreboot will need to run the OPROM to set this up.
With this board, bare support (running without coreboot) is not available
as yet.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since Chromebooks mostly have similar configuration, put it in a common
file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add Lynxpoint to the driver so that the Asus Chromebox can be supported.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
At present a VGA console assumes a keyboard unless a CONFIG option is set.
This difference can be dealt with by a device tree option, allowing boards
that are otherwise the same to use the same configuration.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some systems have more than 4GB of RAM. U-Boot can only place things below
4GB so any memory above that should not be used. Ignore any such memory so
that the memory size will not exceed the maximum.
This prevents gd->ram_size exceeding 4GB which causes problems for PCI
devices which use DMA.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Commit d3cfcb3 (ARM: DRA7: Enable clocks for USB OTGSS and USB PHY)
changed the member names of prcm_regs from cm_l3init_usb_otg_ss_clkctrl
to cm_l3init_usb_otg_ss1_clkctrl and from cm_coreaon_usb_phy_core_clkctrl
to cm_coreaon_usb_phy1_core_clkctrl in order to differentiate between
the two dwc3 controllers present in dra7xx/am43xx and enabled these
clocks in enable_basic_clocks() in hw_data.c. However these clocks
continued to be enabled in board files/driver files for dwc3 host
mode functionality causing compilation break with few configs.
Fixed it here by making all the clocks enabled in enable_basic_clocks()
and removing it from board files/driver files here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The TTBR0 register and Table Descriptors of the ARMv7 TLB weren't being
properly set to allow for the configuration specified caching modes to
be active over DRAM. This commit fixes those issues.
Signed-off-by: Bryan Brinsko <bryan.brinsko@rockwellcollins.com>
This enables ARMv7 barrier operations support when
march=armv7-a is enabled.
Using CP15 barriers causes U-Boot bootm command crash when
transferring control to the loaded image on Renesas R8A7794 Cortex A7 CPU.
Using ARMv7 barrier operations instead of the deprecated CP15 barriers
helps to avoid these issues.
Signed-off-by: Valentine Barshak <valentine.barshak+renesas@cogentembedded.com>
Signed-off-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Linux-arm64 require that CNTVOFF_EL2 should be programmed with
a consistent value on all cpus. Initializing CNTVOFF_EL2 at state
transition instead of start.S could prevent potential different value
on cpus if ATF exist and u-boot runs at only one cpu.
Signed-off-by: David Feng <fenghua@phytium.com.cn>
This commit copies implementation of the find_next_zero_bit() from
git://git.denx.de/u-boot.git/arch/mips/include/asm/bitops.h. v2014.07
The function is required to enable MCAST_TFTP support for ARM platforms.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Sunxi platforms come with at least 3 TWI (I2C) controllers and some platforms
even have up to 5. This adds support for every controller on each supported
platform, which is especially useful when using expansion ports on single-board-
computers.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Orion5x, Kirkwood and Armada XP platforms come with a single TWSI (I2C) MVTWSI
controller. However, other platforms using MVTWSI may come with more: this is
the case on Allwinner (sunxi) platforms, where up to 4 controllers can be found
on the same chip.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
A few dram files were still listed as maintained even though they were removed
some time ago
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
vbus-usable may not get set if power is provided through both the power barrel
connector and external 5v is also present on the otg connector, at least on
boards where vbus is also controlled through the axp221-pmic.
One way to reproduce this is to bootup an Ippo-q8h board with a usb-host
cable plugged into the otg (so that it will get powered), then unplug the
usb-host cable and plug in a charger, and then do "reset" on the u-boot
console, vbus-usable will then report 0, leading to uboot trying to provide
power to the otg port even though external 5v is present, this commit fixes
this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
When u-boot boots the board may be powering vbus, we turn off vbus in
sunxi_usbc_request_resources, if we are too quick with reading vusb-detect
after this we may see a residual charge and assume we've an external vusb
connected even though we do not. So when we see an external vusb wait a bit
and try again.
Without this when dealing with a pmic controller vbus and doing "reset" on
the u-boot console the musb host will only init once every other boot, because
the other boot it thinks an external vbus is present, this commit fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
On boards which use the pmic to enable/disable vbus on the otg port, the
vbus value is not reset to 0 on reset, as reset only resets the SoC and not
the pmic, so explicitly set vbus to 0 on init (request_resources) by moving
the gpio_direction_output call into request_resources.
For consistency also move the gpio_direction_input call for vbus-detect into
request_resources.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The Yones Toptech BD1078 is an A20 based 10" tablet with a 1024x600 lcd screen,
volume up/down and back buttons, headphones jack, mini hdmi, micro usb (otg),
micro usb (host), external micro-sd slot and a separate internal micro-sd slot.
Also see: http://linux-sunxi.org/Yones_Toptech_BD1078
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Sunxi platforms have different possible mmc pin mux setups (except for mmc0),
which are different across platforms.
This lets users configure which is used through the CONFIG_MMC*_PINS Kconfig
options. This is especially relevant when a second (in addition to mmc0) port
is used and CONFIG_MMC_SUNXI_SLOT_EXTRA is enabled.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Each hardware feature exposed through the GPIO pin mux is usually using the same
function index (for a given port), so there is no need to define one value per
pin: one value per hardware feature per port is sufficient, avoids duplication
and makes everything easier to understand.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Ainol AW1 is an A20 based tablet with a 800x480 lcd screen, sdio wifi,
volume up/down and home buttons, micro-sd slot, micro usb (otg), headphones
connector and a SPCI modem connector.
Also see: http://linux-sunxi.org/Ainol_AW1
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
VBUS detection could be needed not only by the musb code (to prevent host mode),
but also by e.g. gadget drivers to start only when a cable is connected.
In addition, this allows more flexibility in vbus detection, as it could easily
be extended to other USBC indexes. Eventually, this would help making musb
support independent from a hardcoded USB controller index (0).
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
VBUS detection and enable is now be used with virtual AXP GPIOs, so all the USB
code has to use GPIO in every case and let sunxi_gpio do the heavy lifting.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This converts the VBUS detection and enable logic to GPIO instead of separate
axp functions and checks that have to be used aside usual GPIO functions.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Mixtile LOFT-Q is an A31 based board with 2G RAM, 8G EMMC, sdio wifi,
1Gbit ethernet, HDMI display, toslink audio plug, 4 USB2.0 port, external
USB2SATA connector, sd card plug, 3x60 external fpic expansion connector,
NXP JN5168 zigbee gw, remote support.
Also see http://focalcrest.com/en/pc.html#pro02
Signed-off-by: Han Pengfei <pengphei@sina.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The "fastboot reboot-bootloader" command is defined to
re-enter into fastboot mode after rebooting into
bootloader. This command is usually used after updating
bootloader via fastboot.
This commit implements only a generic side of the
command - setting of the reset flag and then resetting.
Setting of the reset flag is implemented using __weak
fb_set_reboot_flag() function. The actual setting and
checking of the reset flag should be implemented by
a boot script and/or board/SoC specific code.
Signed-off-by: Alexey Firago <alexey_firago@mentor.com>
Tested-by: Steve Rae <srae@broadcom.com>
[Test HW: bcm28155_ap board]
Implement an alias name check for devices where GPT limitations prevent
user-friendly partition names such as "boot", "system" and "cache". Or,
where the actual partition name doesn't match a standard partition name
used commonly with fastboot.
To set an alias, add an environment setting as follows:
fastboot_partition_alias_<alias partition name>=<actual partition name>
Example: fastboot_partition_alias_boot=LNX
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Acked-by: Steve Rae <srae@broadcom.com>
Cc: Steve Rae <srae@broadcom.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
trigger watchdog before calling usb_gadget_handle_interrupts()
This prevents board resets when calling dfu command on boards
which have a watchdog.
Signed-off-by: Heiko Schocher <hs@denx.de>
[ Reedition by Lukasz Majewski <l.majewski@samsung.com> to apply to
v2014.04 release ]
For u-boot dwc3 driver the scatter gather list support has been removed
from original linux code. It is correct, since we try to send one request
at a time.
However, the cleanup left spurious break, which caused early exit from
loop at dwc3_cleanup_done_reqs() function. As a result the dwc3_gadget_giveback()
wasn't called and caused USB Mass Storage to hang.
This commit removes this problem and refactor the code to remove superfluous
do { } while(1) loop.
Test HW: Odroid XU3 (with ./test/ums/ums_gadget_test.sh)
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Commit "drivers/dwc3: add a workaround for too small OUT requests"
sets max packet for OUT requests when transfer is smaller.
Until this change the default maxpacket for non EP0 EPs was 1024. This is
too much, since UMS LBA size is 512B
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
It turned out that current dwc3 gadget code is preparing multiple TRBs
for a transfer. Unfortunately, when multiple requests are in the same
queue, only for the last one the LST (last) ctrl bit is set.
Due to that dwc3 HW executes all TRBs up till the one marked as last.
Unfortunately, UMS requires call of ->complete callback after any send TRB.
This is the reason for "hangs" in executing UMS.
This code simplifies this situation and set each TRB's ctrl field bit to be
last (LST bit).
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
There is no point in calling dwc3_thread_interrupt() if no event is
pending. There is also no point in flushing event cache in EVERY loop
iteration.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
This patch adds code to select standard, commonly used usb endpoint
configuration (ep1in-bulk, ep2out-bulk, ep3in-int) to dwc3 driver. This
ensures compatibility with old userspace and windows drivers, which
expects hardcoded endpoint numbers.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
DWC3 hangs on OUT requests smaller than maxpacket size,
so HACK the request length to be at least equal to maxpacket size.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
This commit makes the dwc3_set_mode() as static, to prevent collisions.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
The BIT() macro is used only in those places, so it is reasonable to
replace it by a constant value.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
DWC3 UDC driver requires presence of .reset callback in a composite driver.
This setting is similar to the one nowadays present in linux kernel.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
This patch invokes board-specific USB cleanup (board_usb_cleanup)
function in the mass storage gadget
Signed-off-by: Inha Song <ideal.song@samsung.com>
Since we support multiple dwc3 controllers to be existent at the same
time, in order to handle the interrupts of a particular dwc3 controller
usb_gadget_handle_interrutps should take controller index as an
argument.
Hence the API of usb_gadget_handle_interrupts is modified to take
controller index as an argument and made the corresponding changes to all
the usb_gadget_handle_interrupts calls.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Enabled dwc3, dwc3-omap and PHY for dwc3 are enabled. Also enabled
support for DFU.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Implemented board_usb_init(), board_usb_cleanup() and
usb_gadget_handle_interrupts() in am43xx board file that
can be invoked by various gadget drivers.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Enabled dwc3, dwc3-omap and PHY for dwc3 are enabled. Also enabled
support for DFU.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Implemented board_usb_init(), board_usb_cleanup() and
usb_gadget_handle_interrupts() in dra7xx board file that
can be invoked by various gadget drivers.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Invoked board_usb_cleanup for cleaning up initialized USB. It
will be invoked if the user enterts ctrl-C.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Taken from linux kernel with commit
commit 765f5b830e547229bb752e7b232ee83e2b3d49d5
Author: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Date: Thu Jun 23 14:26:11 2011 +0200
usb: gadget: defer setting maxpacket till ->setup()
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Now that the entire dwc3 driver is adapted to compile with uboot build,
modify the Makefiles so that the dwc3 driver can be built.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
dwc3 can do only max packet aligned transfers. So in case request length
is not max packet aligned and is bigger than DWC3_EP0_BOUNCE_SIZE
two chained TRBs is required to handle the transfer.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
No functional change. Modified few things so that there are no
code duplication while implementing chained TRB.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
In the linux kernel, non cacheable buffers are used. However in uboot
since there are no APIs to allocate non cacheable memory, all
the buffers should be flushed before using it.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Added a single driver for both USB2 PHY programming and USB3 PHY
programming.
USB3 PHY is taken from drivers/phy/phy-ti-pipe3.c in linux kernel.
commit 56042e : phy: ti-pipe3: Fix suspend/resume and module reload.
USB2 PHY is taken from drivers/phy/phy-omap-usb2.c in linux kernel.
commit eb82a3 : phy: omap-usb2: Balance pm_runtime_enable() on probe
failure and remove.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Added an API to check for interrupt status. This API is generally
called from board file to check for interrupt status.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Added support for multiple dwc3 omap controllers. This gives uboot
the capability to control multiple dwc3 omap controllers.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Removed probe and remove that are specific to linux and replaced it with
uboot init and uboot exit. These functions will be invoked from boardfile.
This will change once we have dwc3-omap driver adapted to use the uboot
driver model.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Added a structure to populate dwc3 omap platform data. The board file should
populate these platform data before invoking dwc3 omap driver.
This will be removed once dwc3-omap driver is adapted to use the driver model.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
*) Changed the included header files to that used in u-boot.
*) Removed extcon_* APIs
*) Removed regulator_* APIs
*) Fixed other misc warnings
*) Added dwc3-omap.h to include the definitions of UTMI modes.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Since interrupt support is not present in u-boot, added an
API to handle the interrupts in dwc3 core. This API can be
polled to handle the interrupts.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Added support for multiple dwc3 controllers. This gives uboot
the capability to control multiple dwc3 controllers.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Removed probe and remove that are specific to linux and replaced it with
uboot init and uboot exit. These functions will be invoked from boardfile.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Added a structure to populate dwc3 core platform data. The board file should
populate these platform data before invoking dwc3 driver.
This will be removed once we have dwc3 driver adapted to use the driver model.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
*) Changed the include header files to that used in u-boot.
*) Removed phy_* APIs
*) Removed jiffies and used a simple while loop
*) Used dma_alloc_coherent and dma_free_coherent APIs of u-boot
*) Fixed other misc warnings
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Added USB_GADGET_DELAYED_STATUS to avoid the following compilation error.
error: ‘USB_GADGET_DELAYED_STATUS’ undeclared (first use in this function)
while compiling dwc3/ep0.c
While this is been added only to avoid compilation error, the complete fix
should be something like the one added in linux kernel. The complete fix
will be ported once we have the composite driver in u-boot look similar to
the one in linux kernel.
commit 1b9ba000177ee47bcc5b44c7c34e48e735f5f9b1
Author: Roger Quadros <roger.quadros@nokia.com>
Date: Mon May 9 13:08:06 2011 +0300
usb: gadget: composite: Allow function drivers to pause control transfers
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
*) Changed the included header files to that used in u-boot.
*) added dwc3_ep_event_string() used in ep0.c
*) Fixed other misc warnings
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Added resource_size_t type in order to get rid of the following
compilation error whiel building dwc3 gadget.
include/linux/ioport.h:19:2: error: unknown type name ‘resource_size_t’
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Did a bunch of things to get dwc3/gadget.c compile in u-boot without
build errors and warnings
*) Changed the included header files to that used in u-boot.
*) Used dma_alloc_coherent and dma_free_coherent APIs of u-boot
*) removed sg support
*) remove jiffies and used a simple while loop
*) removed irq support and added a function to call these interrupt handler.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Added a header file to include various linux specific APIs like
pr_debug, WARN_ WARN_ON_ONCE etc.. in order to avoid compilation
error while building dwc3 driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Added dma_free_coherent corresponding to the dma_alloc_coherent in
dma-mapping.h in order to free memory allocated using dma_alloc_coherent.
This API is used in dwc3 driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Removed all pm related operations including pm_runtime APIs,
suspend/resume hooks as support for these are not present in u-boot.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Changed the header files included in core.h and io.h to the u-boot header
files so that these files can be included in other dwc3 source files and
be compiled in uboot. Also added otg.h which has the defines for dr_mode.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Removed most of the trace_* APIs from dwc3 driver since tracepoints are not
supported in u-boot. Replaced some of the trace_* API with dev_dbg/dev/vdbg.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Review-by: Lukasz Majewski <l.majewski@samsung.com>
Modified the file header to the format that is used in u-boot. Also
included in the header, the commit in linux kernel from which each of
these files are added.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
removed un-used/un-supported files from dwc3. These files can be added
later as and when the support is added.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Added dwc3 folder from linux kernel 3.19-rc1 (97bf6af1f9)
to u-boot. This will be adapted to work with u-boot in the
following patches.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Fixed the following warning here.
"warning: ‘dma_alloc_coherent’ defined but not used" while compiling
udc-core
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Make udc-core compile in u-boot by removing all linux specific
stuff and having only the bare minimal udc-core required for
usb gadget drivers. Also modified the file header to a format that is
generally being used in u-boot.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Made changes in gadget.h that is required after adding udc-core.c
except changes that might break other platforms.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Added udc-core.c from linux kernel 3.19-rc1 (97bf6af1f9) to u-boot.
This will be adapted to work with u-boot in the
following patches.
Adding support for udc will help to seamlessly port dwc3 driver from
linux kernel to u-boot (since dwc3 uses udc-core) and it'll also help
to add support for multiple gadget controllers to be functional at the
same time.
All other gadget drivers can also be adapted to use udc-core.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Enabled clocks for dwc3 controller and USB PHY present in AM43xx.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Enabled clocks for dwc3 controller and USB PHY present in DRA7.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
IIUC, interrupt transfers are NAK'd by devices until they wish to trigger
an interrupt, and e.g. EHCI controllers retry these in HW until they are
ACK'd. However, DWC2 doesn't seem to retry, so we need to do this in SW.
In practice, I've seen DWC2_HCINT_FRMOVRUN happen too. I'm not quite sure
what this error implies; perhaps it's related to how near the end of a
USB frame we're at when the interrupt transfer is initiated? Anyway,
retrying this temporary error seems to be necessary too.
With all these commits applied, both my USB keyboards (one LS Lenovo and
one FS Dell) work correctly when there is no USB hub between the SoC and
the keyboard; We still need split transactions to be implemented for hubs
to work.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
As best I can tell, there's no difference between bulk and interrupt
transfers in terms of how the HW should be programmed, at least given
that we're executing one transaction at a time rather than scheduling
them into frames for maximum throughput.
This patch ends up sharing the toggle bit state between bulk and
interrupt transfers on a particular EP. However I believe this is fine;
AFAIK a given EP either uses bulk or interrupt transfers and doesn't mix
them.
This patch doesn't do anything with the "interval" parameter for
interrupt transfers, but then most other USB controller drivers in U-Boot
don't either.
It turns out that one of my keyboards is happy to work using control
transfers but the other only gives non-zero "HID reports" via interrupt
transfers.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
A bit must be set in HCCHAR when communicating with low-speed devices.
I have no idea why there's no corresponding bit to distinguish between
full-speed and high-speed devices, but no matter; they all work now!
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
When we communicate with the VideoCore to perform property mailbox
transactions, that is a DMA operation as far as the property buffer
is concerned. Use phys_to_bus() on that buffer.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
This doesn't make my LS keyboard work any better, but it does at least
report the correct speed in "usb tree".
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Use of these APIs is required on the Raspberry Pi. With this change, USB
on RPi1 should be more reliable, and USB on the RPi2 will start working.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
The BCM283[56] contain both a L1 and L2 cache between the GPU (a/k/a
VideoCore CPU?) and DRAM. DMA-capable peripherals can also optionally
access DRAM via this same L2 cache (although they always bypass the L1
cache). Peripherals select whether to use or bypass the cache via the
top two bits of the bus address.
An IOMMU exists between the ARM CPU and the rest of the system. This
controls whether the ARM CPU's accesses use or bypass the L1 and/or L2
cache. This IOMMU is configured/controlled exclusively by the VideoCore
CPU.
In order for DRAM accesses made by the ARM core to be coherent with
accesses made by other DMA peripherals, we must program a bus address
into those peripherals that causes the peripheral's accesses to use the
same set of caches that the ARM core's accesses will use.
On the RPi1, the VideoCore firmware sets up the IOMMU to enable use of
the L2 cache. This corresponds to addresses based at 0x40000000.
On the RPi2, the VideoCore firmware sets up the IOMMU to disable use of
the L2 cache. This corresponds to addresses based at 0xc0000000.
This patch implements U-Boot's phys_to_bus/bus_to_phys APIs according
to those rules.
For full details of this setup, please see Dom Cobley's description at:
http://lists.denx.de/pipermail/u-boot/2015-March/208201.htmlhttp://permalink.gmane.org/gmane.comp.boot-loaders.u-boot/215038https://www.mail-archive.com/u-boot@lists.denx.de/msg166568.html
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
On some SoCs, DMA-capable peripherals see a different address space to
the CPU's physical address space. Create an API to allow platform-agnostic
drivers to convert between the two address spaces when programming DMA
operations.
This API will exist on all platforms, but will have a dummy implementation
when this feature is not required. Other platforms will enable
CONFIG_PHYS_TO_BUS and provide the required implementation.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
When I created wait_for_chhltd(), I noticed that some instances of the
code it replaced expected the ACK bit to be set and others didn't. I
assumed this was an accidental inconsistency in the code, so wrote
wait_for_chhltd() to always expect ACK to be set. This code appeared to
work correctly for both enumeration of USB keyboards and operation of
USB Ethernet devices. However, this change broke USB Mass Storage (at
least my USB SD card reader). This change reverts to exactly the
original behaviour. I'm not sure why the ACK bit isn't always set
(perhaps a quirk in the USB HW or DWC2 controller), but the code works
this way!
Fixes: 5be4ca7d6ac8 ("usb: dwc2: unify waiting for transfer completion")
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Each USB transfer is split up into chunks that are held in an aligned
buffer. This imposes a limit on the size of each chunk, but no limit on
the total size of transferred data. Fix the logic in chunk_msg() not to
reject large transfers, but simply take the size of the aligned buffer
into account when calculating the chunk size.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
The original aligned_buffer usage:
a) Uselessly copied data into the aligned buffer even for IN
transactions. Fix this my making the copy conditional.
b) Always programmed the HW to transfer to/from the start of the aligned
buffer. This worked fine for OUT transactions since the memcpy copied
the OUT data to this location too. However, for large IN transactions,
since the copy from the aligned buffer to the "client" buffer was
deferred until after all chunks were transferred. it resulted in each
chunk's transfer over-writing the data for the first transfer. Fix
this by copying IN data as soon as it's received.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
The control data toggle resets to DATA1 at the start of the data phase
of every setup transaction. We don't need a global variable to store
the value; we can just store it on the stack.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Move the body of submit_bulk_msg() into new function chunk_msg(). This
can be shared with submit_control_msg() to reduce code duplication, and
allow control messages larger than maxpacket.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Some USB devices break the spec and require longer warm-up times. Allow
the usb_pgood_delay env variable to override the calculated time.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
When fetching the first descriptor from a new device, only validate that
we received at least 8 bytes, not that we received the entire descriptor.
The reasoning is:
- The code only uses fields in the first 8 bytes, so that's all we need
to have fetched at this stage.
- The smallest maxpacket size is 8 bytes. Before we know the actual
maxpacket the device uses, the USB controller may only accept a single
packet (see the DWC2 note in the comment added in the commit).
Consequently we are only guaranteed to receive 1 packet (at least 8
bytes) even in a non-error case.
Fixes: 1a7758044b04 ("usb: Early failure when the first descriptor read
fails or is invalid")
Cc: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
This may happen when using an USB1 device on a controller that only supports
USB2 (e.g. EHCI). Reading the first descriptor will fail (read 0 byte), so we
can abort the process at this point instead of failing later and wasting time.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This checks that a new USB device is correctly initialized and frees it if not.
In addition, this doesn't report that USB was started when no device was found.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This patch fixes USB storage capacity detection breakage on 64-bit systems
which arises due to 'unsigned long' length difference. Old code assumes that
to be 32 bit and breaks because of inappropriate response buffer layout.
Also this fixes a number of build warnings and changes big-endian values
treatment style to be architecture-independent
Signed-off-by: Sergey Temerkhanov <s.temerkhanov@gmail.com>
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
This commit allows xHCI to use both 64 and 32 bit memory
physical addresses depending on architecture it's being built for.
Also it makes use of readq()/writeq() on 64-bit systems
Signed-off-by: Sergey Temerkhanov <s.temerkhanov@gmail.com>
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
This patch converts USB protocol headers to use explicitly sized
fields like the rest of the code
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
Signed-off-by: Sergey Temerkhanov <s.temerkhanov@gmail.com>
Cast pointers to unsigned long instead of a sized 32-bit type to avoid
pointer to integer cast size mismatch warnings.
Cc: Tom Warren <twarren@nvidia.com>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Change addresses to unsigned long to be compatible with 64-bit builds.
Regardless of fixing warnings, the device is still only 32-bit capable.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Marek Vasut <marex@denx.de>
Change addresses to unsigned long to be compatible with 64-bit builds.
Regardless of fixing warnings, the device is still only 32-bit capable.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: "Łukasz Majewski" <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Mass storage is not necessary present on interface 0. This
patch allow usb_stor_scan to look in every available interface.
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
2015-04-14 05:47:47 +02:00
1427 changed files with 70584 additions and 12842 deletions
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
