Prepare v2017.09-rc1

Signed-off-by: Tom Rini <trini@konsulko.com>

.gitignore

@@ -8,7 +8,7 @@
 .*
 *.a
 *.bin
-*.cfgtmp
+*.cfgout
 *.dtb
 *.dtb.S
 *.elf

.mailmap

@@ -34,3 +34,4 @@ Wolfgang Denk <wdenk>
 York Sun <yorksun@freescale.com>
 York Sun <york.sun@nxp.com>
 Łukasz Majewski <l.majewski@samsung.com>
+Mirza <Taimoor_Mirza@mentor.com>

Documentation/.gitignore

@@ -0,0 +1,2 @@
+output
+*.pyc

Documentation/Makefile

@@ -0,0 +1,124 @@
+# -*- makefile -*-
+# Makefile for Sphinx documentation
+#
+
+subdir-y :=
+
+# You can set these variables from the command line.
+SPHINXBUILD   = sphinx-build
+SPHINXOPTS    =
+SPHINXDIRS    = .
+_SPHINXDIRS   = $(patsubst $(srctree)/Documentation/%/conf.py,%,$(wildcard $(srctree)/Documentation/*/conf.py))
+SPHINX_CONF   = conf.py
+PAPER         =
+BUILDDIR      = $(obj)/output
+PDFLATEX      = xelatex
+LATEXOPTS     = -interaction=batchmode
+
+# User-friendly check for sphinx-build
+HAVE_SPHINX := $(shell if which $(SPHINXBUILD) >/dev/null 2>&1; then echo 1; else echo 0; fi)
+
+ifeq ($(HAVE_SPHINX),0)
+
+.DEFAULT:
+	$(warning The '$(SPHINXBUILD)' command was not found. Make sure you have Sphinx installed and in PATH, or set the SPHINXBUILD make variable to point to the full path of the '$(SPHINXBUILD)' executable.)
+	@echo
+	@./scripts/sphinx-pre-install
+	@echo "  SKIP    Sphinx $@ target."
+
+else # HAVE_SPHINX
+
+# User-friendly check for pdflatex
+HAVE_PDFLATEX := $(shell if which $(PDFLATEX) >/dev/null 2>&1; then echo 1; else echo 0; fi)
+
+# Internal variables.
+PAPEROPT_a4     = -D latex_paper_size=a4
+PAPEROPT_letter = -D latex_paper_size=letter
+KERNELDOC       = $(srctree)/scripts/kernel-doc
+KERNELDOC_CONF  = -D kerneldoc_srctree=$(srctree) -D kerneldoc_bin=$(KERNELDOC)
+ALLSPHINXOPTS   =  $(KERNELDOC_CONF) $(PAPEROPT_$(PAPER)) $(SPHINXOPTS)
+# the i18n builder cannot share the environment and doctrees with the others
+I18NSPHINXOPTS  = $(PAPEROPT_$(PAPER)) $(SPHINXOPTS) .
+
+# commands; the 'cmd' from scripts/Kbuild.include is not *loopable*
+loop_cmd = $(echo-cmd) $(cmd_$(1)) || exit;
+
+# $2 sphinx builder e.g. "html"
+# $3 name of the build subfolder / e.g. "media", used as:
+#    * dest folder relative to $(BUILDDIR) and
+#    * cache folder relative to $(BUILDDIR)/.doctrees
+# $4 dest subfolder e.g. "man" for man pages at media/man
+# $5 reST source folder relative to $(srctree)/$(src),
+#    e.g. "media" for the linux-tv book-set at ./Documentation/media
+
+quiet_cmd_sphinx = SPHINX  $@ --> file://$(abspath $(BUILDDIR)/$3/$4)
+      cmd_sphinx = $(MAKE) BUILDDIR=$(abspath $(BUILDDIR)) $(build)=Documentation/media $2 && \
+	PYTHONDONTWRITEBYTECODE=1 \
+	BUILDDIR=$(abspath $(BUILDDIR)) SPHINX_CONF=$(abspath $(srctree)/$(src)/$5/$(SPHINX_CONF)) \
+	$(SPHINXBUILD) \
+	-b $2 \
+	-c $(abspath $(srctree)/$(src)) \
+	-d $(abspath $(BUILDDIR)/.doctrees/$3) \
+	-D version=$(KERNELVERSION) -D release=$(KERNELRELEASE) \
+	$(ALLSPHINXOPTS) \
+	$(abspath $(srctree)/$(src)/$5) \
+	$(abspath $(BUILDDIR)/$3/$4)
+
+htmldocs:
+	@+$(foreach var,$(SPHINXDIRS),$(call loop_cmd,sphinx,html,$(var),,$(var)))
+
+linkcheckdocs:
+	@$(foreach var,$(SPHINXDIRS),$(call loop_cmd,sphinx,linkcheck,$(var),,$(var)))
+
+latexdocs:
+	@+$(foreach var,$(SPHINXDIRS),$(call loop_cmd,sphinx,latex,$(var),latex,$(var)))
+
+ifeq ($(HAVE_PDFLATEX),0)
+
+pdfdocs:
+	$(warning The '$(PDFLATEX)' command was not found. Make sure you have it installed and in PATH to produce PDF output.)
+	@echo "  SKIP    Sphinx $@ target."
+
+else # HAVE_PDFLATEX
+
+pdfdocs: latexdocs
+	$(foreach var,$(SPHINXDIRS), $(MAKE) PDFLATEX=$(PDFLATEX) LATEXOPTS="$(LATEXOPTS)" -C $(BUILDDIR)/$(var)/latex || exit;)
+
+endif # HAVE_PDFLATEX
+
+epubdocs:
+	@+$(foreach var,$(SPHINXDIRS),$(call loop_cmd,sphinx,epub,$(var),epub,$(var)))
+
+xmldocs:
+	@+$(foreach var,$(SPHINXDIRS),$(call loop_cmd,sphinx,xml,$(var),xml,$(var)))
+
+endif # HAVE_SPHINX
+
+# The following targets are independent of HAVE_SPHINX, and the rules should
+# work or silently pass without Sphinx.
+
+refcheckdocs:
+	$(Q)cd $(srctree);scripts/documentation-file-ref-check
+
+cleandocs:
+	$(Q)rm -rf $(BUILDDIR)
+	$(Q)$(MAKE) BUILDDIR=$(abspath $(BUILDDIR)) $(build)=Documentation/media clean
+
+dochelp:
+	@echo  ' Linux kernel internal documentation in different formats from ReST:'
+	@echo  '  htmldocs        - HTML'
+	@echo  '  latexdocs       - LaTeX'
+	@echo  '  pdfdocs         - PDF'
+	@echo  '  epubdocs        - EPUB'
+	@echo  '  xmldocs         - XML'
+	@echo  '  linkcheckdocs   - check for broken external links (will connect to external hosts)'
+	@echo  '  refcheckdocs    - check for references to non-existing files under Documentation'
+	@echo  '  cleandocs       - clean all generated files'
+	@echo
+	@echo  '  make SPHINXDIRS="s1 s2" [target] Generate only docs of folder s1, s2'
+	@echo  '  valid values for SPHINXDIRS are: $(_SPHINXDIRS)'
+	@echo
+	@echo  '  make SPHINX_CONF={conf-file} [target] use *additional* sphinx-build'
+	@echo  '  configuration. This is e.g. useful to build with nit-picking config.'
+	@echo
+	@echo  '  Default location for the generated documents is Documentation/output'

Documentation/conf.py

@@ -0,0 +1,528 @@
+# -*- coding: utf-8 -*-
+#
+# The U-Boot documentation build configuration file, created by
+# sphinx-quickstart on Fri Feb 12 13:51:46 2016.
+#
+# This file is execfile()d with the current directory set to its
+# containing dir.
+#
+# Note that not all possible configuration values are present in this
+# autogenerated file.
+#
+# All configuration values have a default; values that are commented out
+# serve to show the default.
+
+import sys
+import os
+import sphinx
+
+# Get Sphinx version
+major, minor, patch = sphinx.version_info[:3]
+
+
+# If extensions (or modules to document with autodoc) are in another directory,
+# add these directories to sys.path here. If the directory is relative to the
+# documentation root, use os.path.abspath to make it absolute, like shown here.
+sys.path.insert(0, os.path.abspath('sphinx'))
+from load_config import loadConfig
+
+# -- General configuration ------------------------------------------------
+
+# If your documentation needs a minimal Sphinx version, state it here.
+needs_sphinx = '1.3'
+
+# Add any Sphinx extension module names here, as strings. They can be
+# extensions coming with Sphinx (named 'sphinx.ext.*') or your custom
+# ones.
+extensions = ['kerneldoc', 'rstFlatTable', 'kernel_include', 'cdomain', 'kfigure']
+
+# The name of the math extension changed on Sphinx 1.4
+if major == 1 and minor > 3:
+    extensions.append("sphinx.ext.imgmath")
+else:
+    extensions.append("sphinx.ext.pngmath")
+
+# Add any paths that contain templates here, relative to this directory.
+templates_path = ['_templates']
+
+# The suffix(es) of source filenames.
+# You can specify multiple suffix as a list of string:
+# source_suffix = ['.rst', '.md']
+source_suffix = '.rst'
+
+# The encoding of source files.
+#source_encoding = 'utf-8-sig'
+
+# The master toctree document.
+master_doc = 'index'
+
+# General information about the project.
+project = 'Das U-Boot'
+copyright = 'The U-Boot development community'
+author = 'The U-Boot development community'
+
+# The version info for the project you're documenting, acts as replacement for
+# |version| and |release|, also used in various other places throughout the
+# built documents.
+#
+# In a normal build, version and release are are set to KERNELVERSION and
+# KERNELRELEASE, respectively, from the Makefile via Sphinx command line
+# arguments.
+#
+# The following code tries to extract the information by reading the Makefile,
+# when Sphinx is run directly (e.g. by Read the Docs).
+try:
+    makefile_version = None
+    makefile_patchlevel = None
+    for line in open('../Makefile'):
+        key, val = [x.strip() for x in line.split('=', 2)]
+        if key == 'VERSION':
+            makefile_version = val
+        elif key == 'PATCHLEVEL':
+            makefile_patchlevel = val
+        if makefile_version and makefile_patchlevel:
+            break
+except:
+    pass
+finally:
+    if makefile_version and makefile_patchlevel:
+        version = release = makefile_version + '.' + makefile_patchlevel
+    else:
+        version = release = "unknown version"
+
+# The language for content autogenerated by Sphinx. Refer to documentation
+# for a list of supported languages.
+#
+# This is also used if you do content translation via gettext catalogs.
+# Usually you set "language" from the command line for these cases.
+language = None
+
+# There are two options for replacing |today|: either, you set today to some
+# non-false value, then it is used:
+#today = ''
+# Else, today_fmt is used as the format for a strftime call.
+#today_fmt = '%B %d, %Y'
+
+# List of patterns, relative to source directory, that match files and
+# directories to ignore when looking for source files.
+exclude_patterns = ['output']
+
+# The reST default role (used for this markup: `text`) to use for all
+# documents.
+#default_role = None
+
+# If true, '()' will be appended to :func: etc. cross-reference text.
+#add_function_parentheses = True
+
+# If true, the current module name will be prepended to all description
+# unit titles (such as .. function::).
+#add_module_names = True
+
+# If true, sectionauthor and moduleauthor directives will be shown in the
+# output. They are ignored by default.
+#show_authors = False
+
+# The name of the Pygments (syntax highlighting) style to use.
+pygments_style = 'sphinx'
+
+# A list of ignored prefixes for module index sorting.
+#modindex_common_prefix = []
+
+# If true, keep warnings as "system message" paragraphs in the built documents.
+#keep_warnings = False
+
+# If true, `todo` and `todoList` produce output, else they produce nothing.
+todo_include_todos = False
+
+primary_domain = 'c'
+highlight_language = 'none'
+
+# -- Options for HTML output ----------------------------------------------
+
+# The theme to use for HTML and HTML Help pages.  See the documentation for
+# a list of builtin themes.
+
+# The Read the Docs theme is available from
+# - https://github.com/snide/sphinx_rtd_theme
+# - https://pypi.python.org/pypi/sphinx_rtd_theme
+# - python-sphinx-rtd-theme package (on Debian)
+try:
+    import sphinx_rtd_theme
+    html_theme = 'sphinx_rtd_theme'
+    html_theme_path = [sphinx_rtd_theme.get_html_theme_path()]
+except ImportError:
+    sys.stderr.write('Warning: The Sphinx \'sphinx_rtd_theme\' HTML theme was not found. Make sure you have the theme installed to produce pretty HTML output. Falling back to the default theme.\n')
+
+# Theme options are theme-specific and customize the look and feel of a theme
+# further.  For a list of options available for each theme, see the
+# documentation.
+#html_theme_options = {}
+
+# Add any paths that contain custom themes here, relative to this directory.
+#html_theme_path = []
+
+# The name for this set of Sphinx documents.  If None, it defaults to
+# "<project> v<release> documentation".
+#html_title = None
+
+# A shorter title for the navigation bar.  Default is the same as html_title.
+#html_short_title = None
+
+# The name of an image file (relative to this directory) to place at the top
+# of the sidebar.
+#html_logo = None
+
+# The name of an image file (within the static path) to use as favicon of the
+# docs.  This file should be a Windows icon file (.ico) being 16x16 or 32x32
+# pixels large.
+#html_favicon = None
+
+# Add any paths that contain custom static files (such as style sheets) here,
+# relative to this directory. They are copied after the builtin static files,
+# so a file named "default.css" will overwrite the builtin "default.css".
+
+html_static_path = ['sphinx-static']
+
+html_context = {
+    'css_files': [
+        '_static/theme_overrides.css',
+    ],
+}
+
+# Add any extra paths that contain custom files (such as robots.txt or
+# .htaccess) here, relative to this directory. These files are copied
+# directly to the root of the documentation.
+#html_extra_path = []
+
+# If not '', a 'Last updated on:' timestamp is inserted at every page bottom,
+# using the given strftime format.
+#html_last_updated_fmt = '%b %d, %Y'
+
+# If true, SmartyPants will be used to convert quotes and dashes to
+# typographically correct entities.
+#html_use_smartypants = True
+
+# Custom sidebar templates, maps document names to template names.
+#html_sidebars = {}
+
+# Additional templates that should be rendered to pages, maps page names to
+# template names.
+#html_additional_pages = {}
+
+# If false, no module index is generated.
+#html_domain_indices = True
+
+# If false, no index is generated.
+#html_use_index = True
+
+# If true, the index is split into individual pages for each letter.
+#html_split_index = False
+
+# If true, links to the reST sources are added to the pages.
+#html_show_sourcelink = True
+
+# If true, "Created using Sphinx" is shown in the HTML footer. Default is True.
+#html_show_sphinx = True
+
+# If true, "(C) Copyright ..." is shown in the HTML footer. Default is True.
+#html_show_copyright = True
+
+# If true, an OpenSearch description file will be output, and all pages will
+# contain a <link> tag referring to it.  The value of this option must be the
+# base URL from which the finished HTML is served.
+#html_use_opensearch = ''
+
+# This is the file name suffix for HTML files (e.g. ".xhtml").
+#html_file_suffix = None
+
+# Language to be used for generating the HTML full-text search index.
+# Sphinx supports the following languages:
+#   'da', 'de', 'en', 'es', 'fi', 'fr', 'h', 'it', 'ja'
+#   'nl', 'no', 'pt', 'ro', 'r', 'sv', 'tr'
+#html_search_language = 'en'
+
+# A dictionary with options for the search language support, empty by default.
+# Now only 'ja' uses this config value
+#html_search_options = {'type': 'default'}
+
+# The name of a javascript file (relative to the configuration directory) that
+# implements a search results scorer. If empty, the default will be used.
+#html_search_scorer = 'scorer.js'
+
+# Output file base name for HTML help builder.
+htmlhelp_basename = 'TheUBootdoc'
+
+# -- Options for LaTeX output ---------------------------------------------
+
+latex_elements = {
+# The paper size ('letterpaper' or 'a4paper').
+'papersize': 'a4paper',
+
+# The font size ('10pt', '11pt' or '12pt').
+'pointsize': '8pt',
+
+# Latex figure (float) alignment
+#'figure_align': 'htbp',
+
+# Don't mangle with UTF-8 chars
+'inputenc': '',
+'utf8extra': '',
+
+# Additional stuff for the LaTeX preamble.
+    'preamble': '''
+	% Use some font with UTF-8 support with XeLaTeX
+        \\usepackage{fontspec}
+        \\setsansfont{DejaVu Serif}
+        \\setromanfont{DejaVu Sans}
+        \\setmonofont{DejaVu Sans Mono}
+
+     '''
+}
+
+# Fix reference escape troubles with Sphinx 1.4.x
+if major == 1 and minor > 3:
+    latex_elements['preamble']  += '\\renewcommand*{\\DUrole}[2]{ #2 }\n'
+
+if major == 1 and minor <= 4:
+    latex_elements['preamble']  += '\\usepackage[margin=0.5in, top=1in, bottom=1in]{geometry}'
+elif major == 1 and (minor > 5 or (minor == 5 and patch >= 3)):
+    latex_elements['sphinxsetup'] = 'hmargin=0.5in, vmargin=1in'
+    latex_elements['preamble']  += '\\fvset{fontsize=auto}\n'
+
+# Customize notice background colors on Sphinx < 1.6:
+if major == 1 and minor < 6:
+   latex_elements['preamble']  += '''
+        \\usepackage{ifthen}
+
+        % Put notes in color and let them be inside a table
+	\\definecolor{NoteColor}{RGB}{204,255,255}
+	\\definecolor{WarningColor}{RGB}{255,204,204}
+	\\definecolor{AttentionColor}{RGB}{255,255,204}
+	\\definecolor{ImportantColor}{RGB}{192,255,204}
+	\\definecolor{OtherColor}{RGB}{204,204,204}
+        \\newlength{\\mynoticelength}
+        \\makeatletter\\newenvironment{coloredbox}[1]{%
+	   \\setlength{\\fboxrule}{1pt}
+	   \\setlength{\\fboxsep}{7pt}
+	   \\setlength{\\mynoticelength}{\\linewidth}
+	   \\addtolength{\\mynoticelength}{-2\\fboxsep}
+	   \\addtolength{\\mynoticelength}{-2\\fboxrule}
+           \\begin{lrbox}{\\@tempboxa}\\begin{minipage}{\\mynoticelength}}{\\end{minipage}\\end{lrbox}%
+	   \\ifthenelse%
+	      {\\equal{\\py@noticetype}{note}}%
+	      {\\colorbox{NoteColor}{\\usebox{\\@tempboxa}}}%
+	      {%
+	         \\ifthenelse%
+	         {\\equal{\\py@noticetype}{warning}}%
+	         {\\colorbox{WarningColor}{\\usebox{\\@tempboxa}}}%
+		 {%
+	            \\ifthenelse%
+	            {\\equal{\\py@noticetype}{attention}}%
+	            {\\colorbox{AttentionColor}{\\usebox{\\@tempboxa}}}%
+		    {%
+	               \\ifthenelse%
+	               {\\equal{\\py@noticetype}{important}}%
+	               {\\colorbox{ImportantColor}{\\usebox{\\@tempboxa}}}%
+	               {\\colorbox{OtherColor}{\\usebox{\\@tempboxa}}}%
+		    }%
+		 }%
+	      }%
+        }\\makeatother
+
+        \\makeatletter
+        \\renewenvironment{notice}[2]{%
+          \\def\\py@noticetype{#1}
+          \\begin{coloredbox}{#1}
+          \\bf\\it
+          \\par\\strong{#2}
+          \\csname py@noticestart@#1\\endcsname
+        }
+	{
+          \\csname py@noticeend@\\py@noticetype\\endcsname
+          \\end{coloredbox}
+        }
+	\\makeatother
+
+     '''
+
+# With Sphinx 1.6, it is possible to change the Bg color directly
+# by using:
+#	\definecolor{sphinxnoteBgColor}{RGB}{204,255,255}
+#	\definecolor{sphinxwarningBgColor}{RGB}{255,204,204}
+#	\definecolor{sphinxattentionBgColor}{RGB}{255,255,204}
+#	\definecolor{sphinximportantBgColor}{RGB}{192,255,204}
+#
+# However, it require to use sphinx heavy box with:
+#
+#	\renewenvironment{sphinxlightbox} {%
+#		\\begin{sphinxheavybox}
+#	}
+#		\\end{sphinxheavybox}
+#	}
+#
+# Unfortunately, the implementation is buggy: if a note is inside a
+# table, it isn't displayed well. So, for now, let's use boring
+# black and white notes.
+
+# Grouping the document tree into LaTeX files. List of tuples
+# (source start file, target name, title,
+#  author, documentclass [howto, manual, or own class]).
+# Sorted in alphabetical order
+latex_documents = [
+    ('index', 'u-boot-hacker-manual.tex', 'U-Boot Hacker Manual',
+     'The U-Boot development community', 'manual'),
+]
+
+# The name of an image file (relative to this directory) to place at the top of
+# the title page.
+#latex_logo = None
+
+# For "manual" documents, if this is true, then toplevel headings are parts,
+# not chapters.
+#latex_use_parts = False
+
+# If true, show page references after internal links.
+#latex_show_pagerefs = False
+
+# If true, show URL addresses after external links.
+#latex_show_urls = False
+
+# Documents to append as an appendix to all manuals.
+#latex_appendices = []
+
+# If false, no module index is generated.
+#latex_domain_indices = True
+
+
+# -- Options for manual page output ---------------------------------------
+
+# One entry per manual page. List of tuples
+# (source start file, name, description, authors, manual section).
+man_pages = [
+    (master_doc, 'dasuboot', 'The U-Boot Documentation',
+     [author], 1)
+]
+
+# If true, show URL addresses after external links.
+#man_show_urls = False
+
+
+# -- Options for Texinfo output -------------------------------------------
+
+# Grouping the document tree into Texinfo files. List of tuples
+# (source start file, target name, title, author,
+#  dir menu entry, description, category)
+texinfo_documents = [
+    (master_doc, 'DasUBoot', 'The U-Boot Documentation',
+     author, 'DasUBoot', 'One line description of project.',
+     'Miscellaneous'),
+]
+
+# Documents to append as an appendix to all manuals.
+#texinfo_appendices = []
+
+# If false, no module index is generated.
+#texinfo_domain_indices = True
+
+# How to display URL addresses: 'footnote', 'no', or 'inline'.
+#texinfo_show_urls = 'footnote'
+
+# If true, do not generate a @detailmenu in the "Top" node's menu.
+#texinfo_no_detailmenu = False
+
+
+# -- Options for Epub output ----------------------------------------------
+
+# Bibliographic Dublin Core info.
+epub_title = project
+epub_author = author
+epub_publisher = author
+epub_copyright = copyright
+
+# The basename for the epub file. It defaults to the project name.
+#epub_basename = project
+
+# The HTML theme for the epub output. Since the default themes are not
+# optimized for small screen space, using the same theme for HTML and epub
+# output is usually not wise. This defaults to 'epub', a theme designed to save
+# visual space.
+#epub_theme = 'epub'
+
+# The language of the text. It defaults to the language option
+# or 'en' if the language is not set.
+#epub_language = ''
+
+# The scheme of the identifier. Typical schemes are ISBN or URL.
+#epub_scheme = ''
+
+# The unique identifier of the text. This can be a ISBN number
+# or the project homepage.
+#epub_identifier = ''
+
+# A unique identification for the text.
+#epub_uid = ''
+
+# A tuple containing the cover image and cover page html template filenames.
+#epub_cover = ()
+
+# A sequence of (type, uri, title) tuples for the guide element of content.opf.
+#epub_guide = ()
+
+# HTML files that should be inserted before the pages created by sphinx.
+# The format is a list of tuples containing the path and title.
+#epub_pre_files = []
+
+# HTML files that should be inserted after the pages created by sphinx.
+# The format is a list of tuples containing the path and title.
+#epub_post_files = []
+
+# A list of files that should not be packed into the epub file.
+epub_exclude_files = ['search.html']
+
+# The depth of the table of contents in toc.ncx.
+#epub_tocdepth = 3
+
+# Allow duplicate toc entries.
+#epub_tocdup = True
+
+# Choose between 'default' and 'includehidden'.
+#epub_tocscope = 'default'
+
+# Fix unsupported image types using the Pillow.
+#epub_fix_images = False
+
+# Scale large images.
+#epub_max_image_width = 0
+
+# How to display URL addresses: 'footnote', 'no', or 'inline'.
+#epub_show_urls = 'inline'
+
+# If false, no index is generated.
+#epub_use_index = True
+
+#=======
+# rst2pdf
+#
+# Grouping the document tree into PDF files. List of tuples
+# (source start file, target name, title, author, options).
+#
+# See the Sphinx chapter of http://ralsina.me/static/manual.pdf
+#
+# FIXME: Do not add the index file here; the result will be too big. Adding
+# multiple PDF files here actually tries to get the cross-referencing right
+# *between* PDF files.
+pdf_documents = [
+    ('uboot-documentation', u'U-Boot', u'U-Boot', u'J. Random Bozo'),
+]
+
+# kernel-doc extension configuration for running Sphinx directly (e.g. by Read
+# the Docs). In a normal build, these are supplied from the Makefile via command
+# line arguments.
+kerneldoc_bin = '../scripts/kernel-doc'
+kerneldoc_srctree = '..'
+
+# ------------------------------------------------------------------------------
+# Since loadConfig overwrites settings from the global namespace, it has to be
+# the last statement in the conf.py file
+# ------------------------------------------------------------------------------
+loadConfig(globals())

Documentation/index.rst

@@ -0,0 +1,117 @@
+====================
+U-Boot Hacker Manual
+====================
+
+Linker-Generated Arrays
+=======================
+
+A linker list is constructed by grouping together linker input
+sections, each containing one entry of the list. Each input section
+contains a constant initialized variable which holds the entry's
+content. Linker list input sections are constructed from the list
+and entry names, plus a prefix which allows grouping all lists
+together. Assuming _list and _entry are the list and entry names,
+then the corresponding input section name is
+
+::
+
+  .u_boot_list_ + 2_ + @_list + _2_ + @_entry
+
+and the C variable name is
+
+::
+
+  _u_boot_list + _2_ + @_list + _2_ + @_entry
+
+This ensures uniqueness for both input section and C variable name.
+
+Note that the names differ only in the first character, "." for the
+section and "_" for the variable, so that the linker cannot confuse
+section and symbol names. From now on, both names will be referred
+to as
+
+::
+
+  %u_boot_list_ + 2_ + @_list + _2_ + @_entry
+
+Entry variables need never be referred to directly.
+
+The naming scheme for input sections allows grouping all linker lists
+into a single linker output section and grouping all entries for a
+single list.
+
+Note the two '_2_' constant components in the names: their presence
+allows putting a start and end symbols around a list, by mapping
+these symbols to sections names with components "1" (before) and
+"3" (after) instead of "2" (within).
+Start and end symbols for a list can generally be defined as
+
+::
+
+  %u_boot_list_2_ + @_list + _1_...
+  %u_boot_list_2_ + @_list + _3_...
+
+Start and end symbols for the whole of the linker lists area can be
+defined as
+
+::
+
+  %u_boot_list_1_...
+  %u_boot_list_3_...
+
+Here is an example of the sorted sections which result from a list
+"array" made up of three entries : "first", "second" and "third",
+iterated at least once.
+
+::
+
+  .u_boot_list_2_array_1
+  .u_boot_list_2_array_2_first
+  .u_boot_list_2_array_2_second
+  .u_boot_list_2_array_2_third
+  .u_boot_list_2_array_3
+
+If lists must be divided into sublists (e.g. for iterating only on
+part of a list), one can simply give the list a name of the form
+'outer_2_inner', where 'outer' is the global list name and 'inner'
+is the sub-list name. Iterators for the whole list should use the
+global list name ("outer"); iterators for only a sub-list should use
+the full sub-list name ("outer_2_inner").
+
+Here is an example of the sections generated from a global list
+named "drivers", two sub-lists named "i2c" and "pci", and iterators
+defined for the whole list and each sub-list:
+
+::
+
+  %u_boot_list_2_drivers_1
+  %u_boot_list_2_drivers_2_i2c_1
+  %u_boot_list_2_drivers_2_i2c_2_first
+  %u_boot_list_2_drivers_2_i2c_2_first
+  %u_boot_list_2_drivers_2_i2c_2_second
+  %u_boot_list_2_drivers_2_i2c_2_third
+  %u_boot_list_2_drivers_2_i2c_3
+  %u_boot_list_2_drivers_2_pci_1
+  %u_boot_list_2_drivers_2_pci_2_first
+  %u_boot_list_2_drivers_2_pci_2_second
+  %u_boot_list_2_drivers_2_pci_2_third
+  %u_boot_list_2_drivers_2_pci_3
+  %u_boot_list_2_drivers_3
+
+.. kernel-doc:: include/linker_lists.h
+   :internal:
+
+Serial system
+=============
+
+.. kernel-doc:: drivers/serial/serial.c
+   :internal:
+
+The U-Boot EFI subsystem
+========================
+
+Boot services
+-------------
+
+.. kernel-doc:: lib/efi_loader/efi_boottime.c
+   :internal:

Documentation/media/Makefile

@@ -0,0 +1,38 @@
+# Rules to convert a .h file to inline RST documentation
+
+SRC_DIR=$(srctree)/Documentation/media
+PARSER = $(srctree)/Documentation/sphinx/parse-headers.pl
+API = $(srctree)/include
+
+FILES = linker_lists.h.rst
+
+TARGETS := $(addprefix $(BUILDDIR)/, $(FILES))
+
+gen_rst = \
+	echo ${PARSER} $< $@ $(SRC_DIR)/$(notdir $@).exceptions; \
+	${PARSER} $< $@ $(SRC_DIR)/$(notdir $@).exceptions
+
+quiet_gen_rst = echo '  PARSE   $(patsubst $(srctree)/%,%,$<)'; \
+	${PARSER} $< $@ $(SRC_DIR)/$(notdir $@).exceptions
+
+silent_gen_rst = ${gen_rst}
+
+$(BUILDDIR)/linker_lists.h.rst: ${API}/linker_lists.h ${PARSER} $(SRC_DIR)/linker_lists.h.rst.exceptions
+	@$($(quiet)gen_rst)
+
+# Media build rules
+
+.PHONY: all html epub xml latex
+
+all: $(IMGDOT) $(BUILDDIR) ${TARGETS}
+html: all
+epub: all
+xml: all
+latex: $(IMGPDF) all
+linkcheck:
+
+clean:
+	-rm -f $(DOTTGT) $(IMGTGT) ${TARGETS} 2>/dev/null
+
+$(BUILDDIR):
+	$(Q)mkdir -p $@

Documentation/sphinx-static/theme_overrides.css

@@ -0,0 +1,89 @@
+/* -*- coding: utf-8; mode: css -*-
+ *
+ * Sphinx HTML theme customization: read the doc
+ *
+ */
+
+/* Interim: Code-blocks with line nos - lines and line numbers don't line up.
+ * see: https://github.com/rtfd/sphinx_rtd_theme/issues/419
+ */
+
+div[class^="highlight"] pre {
+    line-height: normal;
+}
+.rst-content .highlight > pre {
+    line-height: normal;
+}
+
+@media screen {
+
+    /* content column
+     *
+     * RTD theme's default is 800px as max width for the content, but we have
+     * tables with tons of columns, which need the full width of the view-port.
+     */
+
+    .wy-nav-content{max-width: none; }
+
+    /* table:
+     *
+     *   - Sequences of whitespace should collapse into a single whitespace.
+     *   - make the overflow auto (scrollbar if needed)
+     *   - align caption "left" ("center" is unsuitable on vast tables)
+     */
+
+    .wy-table-responsive table td { white-space: normal; }
+    .wy-table-responsive { overflow: auto; }
+    .rst-content table.docutils caption { text-align: left; font-size: 100%; }
+
+    /* captions:
+     *
+     *   - captions should have 100% (not 85%) font size
+     *   - hide the permalink symbol as long as link is not hovered
+     */
+
+    .toc-title {
+        font-size: 150%;
+	font-weight: bold;
+    }
+
+    caption, .wy-table caption, .rst-content table.field-list caption {
+        font-size: 100%;
+    }
+    caption a.headerlink { opacity: 0; }
+    caption a.headerlink:hover { opacity: 1; }
+
+    /* Menu selection and keystrokes */
+
+    span.menuselection {
+	color: blue;
+	font-family: "Courier New", Courier, monospace
+    }
+
+    code.kbd, code.kbd span {
+	color: white;
+	background-color: darkblue;
+	font-weight: bold;
+	font-family: "Courier New", Courier, monospace
+    }
+
+    /* fix bottom margin of lists items */
+
+    .rst-content .section ul li:last-child, .rst-content .section ul li p:last-child {
+          margin-bottom: 12px;
+    }
+
+    /* inline literal: drop the borderbox, padding and red color */
+
+    code, .rst-content tt, .rst-content code {
+        color: inherit;
+        border: none;
+        padding: unset;
+        background: inherit;
+        font-size: 85%;
+    }
+
+    .rst-content tt.literal,.rst-content tt.literal,.rst-content code.literal {
+        color: inherit;
+    }
+}

Documentation/sphinx/cdomain.py

@@ -0,0 +1,165 @@
+# -*- coding: utf-8; mode: python -*-
+# pylint: disable=W0141,C0113,C0103,C0325
+u"""
+    cdomain
+    ~~~~~~~
+
+    Replacement for the sphinx c-domain.
+
+    :copyright:  Copyright (C) 2016  Markus Heiser
+    :license:    GPL Version 2, June 1991 see Linux/COPYING for details.
+
+    List of customizations:
+
+    * Moved the *duplicate C object description* warnings for function
+      declarations in the nitpicky mode. See Sphinx documentation for
+      the config values for ``nitpick`` and ``nitpick_ignore``.
+
+    * Add option 'name' to the "c:function:" directive.  With option 'name' the
+      ref-name of a function can be modified. E.g.::
+
+          .. c:function:: int ioctl( int fd, int request )
+             :name: VIDIOC_LOG_STATUS
+
+      The func-name (e.g. ioctl) remains in the output but the ref-name changed
+      from 'ioctl' to 'VIDIOC_LOG_STATUS'. The function is referenced by::
+
+          * :c:func:`VIDIOC_LOG_STATUS` or
+          * :any:`VIDIOC_LOG_STATUS` (``:any:`` needs sphinx 1.3)
+
+     * Handle signatures of function-like macros well. Don't try to deduce
+       arguments types of function-like macros.
+
+"""
+
+from docutils import nodes
+from docutils.parsers.rst import directives
+
+import sphinx
+from sphinx import addnodes
+from sphinx.domains.c import c_funcptr_sig_re, c_sig_re
+from sphinx.domains.c import CObject as Base_CObject
+from sphinx.domains.c import CDomain as Base_CDomain
+
+__version__  = '1.0'
+
+# Get Sphinx version
+major, minor, patch = sphinx.version_info[:3]
+
+def setup(app):
+
+    app.override_domain(CDomain)
+
+    return dict(
+        version = __version__,
+        parallel_read_safe = True,
+        parallel_write_safe = True
+    )
+
+class CObject(Base_CObject):
+
+    """
+    Description of a C language object.
+    """
+    option_spec = {
+        "name" : directives.unchanged
+    }
+
+    def handle_func_like_macro(self, sig, signode):
+        u"""Handles signatures of function-like macros.
+
+        If the objtype is 'function' and the the signature ``sig`` is a
+        function-like macro, the name of the macro is returned. Otherwise
+        ``False`` is returned.  """
+
+        if not self.objtype == 'function':
+            return False
+
+        m = c_funcptr_sig_re.match(sig)
+        if m is None:
+            m = c_sig_re.match(sig)
+            if m is None:
+                raise ValueError('no match')
+
+        rettype, fullname, arglist, _const = m.groups()
+        arglist = arglist.strip()
+        if rettype or not arglist:
+            return False
+
+        arglist = arglist.replace('`', '').replace('\\ ', '') # remove markup
+        arglist = [a.strip() for a in arglist.split(",")]
+
+        # has the first argument a type?
+        if len(arglist[0].split(" ")) > 1:
+            return False
+
+        # This is a function-like macro, it's arguments are typeless!
+        signode  += addnodes.desc_name(fullname, fullname)
+        paramlist = addnodes.desc_parameterlist()
+        signode  += paramlist
+
+        for argname in arglist:
+            param = addnodes.desc_parameter('', '', noemph=True)
+            # separate by non-breaking space in the output
+            param += nodes.emphasis(argname, argname)
+            paramlist += param
+
+        return fullname
+
+    def handle_signature(self, sig, signode):
+        """Transform a C signature into RST nodes."""
+
+        fullname = self.handle_func_like_macro(sig, signode)
+        if not fullname:
+            fullname = super(CObject, self).handle_signature(sig, signode)
+
+        if "name" in self.options:
+            if self.objtype == 'function':
+                fullname = self.options["name"]
+            else:
+                # FIXME: handle :name: value of other declaration types?
+                pass
+        return fullname
+
+    def add_target_and_index(self, name, sig, signode):
+        # for C API items we add a prefix since names are usually not qualified
+        # by a module name and so easily clash with e.g. section titles
+        targetname = 'c.' + name
+        if targetname not in self.state.document.ids:
+            signode['names'].append(targetname)
+            signode['ids'].append(targetname)
+            signode['first'] = (not self.names)
+            self.state.document.note_explicit_target(signode)
+            inv = self.env.domaindata['c']['objects']
+            if (name in inv and self.env.config.nitpicky):
+                if self.objtype == 'function':
+                    if ('c:func', name) not in self.env.config.nitpick_ignore:
+                        self.state_machine.reporter.warning(
+                            'duplicate C object description of %s, ' % name +
+                            'other instance in ' + self.env.doc2path(inv[name][0]),
+                            line=self.lineno)
+            inv[name] = (self.env.docname, self.objtype)
+
+        indextext = self.get_index_text(name)
+        if indextext:
+            if major == 1 and minor < 4:
+                # indexnode's tuple changed in 1.4
+                # https://github.com/sphinx-doc/sphinx/commit/e6a5a3a92e938fcd75866b4227db9e0524d58f7c
+                self.indexnode['entries'].append(
+                    ('single', indextext, targetname, ''))
+            else:
+                self.indexnode['entries'].append(
+                    ('single', indextext, targetname, '', None))
+
+class CDomain(Base_CDomain):
+
+    """C language domain."""
+    name = 'c'
+    label = 'C'
+    directives = {
+        'function': CObject,
+        'member':   CObject,
+        'macro':    CObject,
+        'type':     CObject,
+        'var':      CObject,
+    }

Documentation/sphinx/kernel_include.py

@@ -0,0 +1,190 @@
+#!/usr/bin/env python3
+# -*- coding: utf-8; mode: python -*-
+# pylint: disable=R0903, C0330, R0914, R0912, E0401
+
+u"""
+    kernel-include
+    ~~~~~~~~~~~~~~
+
+    Implementation of the ``kernel-include`` reST-directive.
+
+    :copyright:  Copyright (C) 2016  Markus Heiser
+    :license:    GPL Version 2, June 1991 see linux/COPYING for details.
+
+    The ``kernel-include`` reST-directive is a replacement for the ``include``
+    directive. The ``kernel-include`` directive expand environment variables in
+    the path name and allows to include files from arbitrary locations.
+
+    .. hint::
+
+      Including files from arbitrary locations (e.g. from ``/etc``) is a
+      security risk for builders. This is why the ``include`` directive from
+      docutils *prohibit* pathnames pointing to locations *above* the filesystem
+      tree where the reST document with the include directive is placed.
+
+    Substrings of the form $name or ${name} are replaced by the value of
+    environment variable name. Malformed variable names and references to
+    non-existing variables are left unchanged.
+"""
+
+# ==============================================================================
+# imports
+# ==============================================================================
+
+import os.path
+
+from docutils import io, nodes, statemachine
+from docutils.utils.error_reporting import SafeString, ErrorString
+from docutils.parsers.rst import directives
+from docutils.parsers.rst.directives.body import CodeBlock, NumberLines
+from docutils.parsers.rst.directives.misc import Include
+
+__version__  = '1.0'
+
+# ==============================================================================
+def setup(app):
+# ==============================================================================
+
+    app.add_directive("kernel-include", KernelInclude)
+    return dict(
+        version = __version__,
+        parallel_read_safe = True,
+        parallel_write_safe = True
+    )
+
+# ==============================================================================
+class KernelInclude(Include):
+# ==============================================================================
+
+    u"""KernelInclude (``kernel-include``) directive"""
+
+    def run(self):
+        path = os.path.realpath(
+            os.path.expandvars(self.arguments[0]))
+
+        # to get a bit security back, prohibit /etc:
+        if path.startswith(os.sep + "etc"):
+            raise self.severe(
+                'Problems with "%s" directive, prohibited path: %s'
+                % (self.name, path))
+
+        self.arguments[0] = path
+
+        #return super(KernelInclude, self).run() # won't work, see HINTs in _run()
+        return self._run()
+
+    def _run(self):
+        """Include a file as part of the content of this reST file."""
+
+        # HINT: I had to copy&paste the whole Include.run method. I'am not happy
+        # with this, but due to security reasons, the Include.run method does
+        # not allow absolute or relative pathnames pointing to locations *above*
+        # the filesystem tree where the reST document is placed.
+
+        if not self.state.document.settings.file_insertion_enabled:
+            raise self.warning('"%s" directive disabled.' % self.name)
+        source = self.state_machine.input_lines.source(
+            self.lineno - self.state_machine.input_offset - 1)
+        source_dir = os.path.dirname(os.path.abspath(source))
+        path = directives.path(self.arguments[0])
+        if path.startswith('<') and path.endswith('>'):
+            path = os.path.join(self.standard_include_path, path[1:-1])
+        path = os.path.normpath(os.path.join(source_dir, path))
+
+        # HINT: this is the only line I had to change / commented out:
+        #path = utils.relative_path(None, path)
+
+        path = nodes.reprunicode(path)
+        encoding = self.options.get(
+            'encoding', self.state.document.settings.input_encoding)
+        e_handler=self.state.document.settings.input_encoding_error_handler
+        tab_width = self.options.get(
+            'tab-width', self.state.document.settings.tab_width)
+        try:
+            self.state.document.settings.record_dependencies.add(path)
+            include_file = io.FileInput(source_path=path,
+                                        encoding=encoding,
+                                        error_handler=e_handler)
+        except UnicodeEncodeError as error:
+            raise self.severe('Problems with "%s" directive path:\n'
+                              'Cannot encode input file path "%s" '
+                              '(wrong locale?).' %
+                              (self.name, SafeString(path)))
+        except IOError as error:
+            raise self.severe('Problems with "%s" directive path:\n%s.' %
+                      (self.name, ErrorString(error)))
+        startline = self.options.get('start-line', None)
+        endline = self.options.get('end-line', None)
+        try:
+            if startline or (endline is not None):
+                lines = include_file.readlines()
+                rawtext = ''.join(lines[startline:endline])
+            else:
+                rawtext = include_file.read()
+        except UnicodeError as error:
+            raise self.severe('Problem with "%s" directive:\n%s' %
+                              (self.name, ErrorString(error)))
+        # start-after/end-before: no restrictions on newlines in match-text,
+        # and no restrictions on matching inside lines vs. line boundaries
+        after_text = self.options.get('start-after', None)
+        if after_text:
+            # skip content in rawtext before *and incl.* a matching text
+            after_index = rawtext.find(after_text)
+            if after_index < 0:
+                raise self.severe('Problem with "start-after" option of "%s" '
+                                  'directive:\nText not found.' % self.name)
+            rawtext = rawtext[after_index + len(after_text):]
+        before_text = self.options.get('end-before', None)
+        if before_text:
+            # skip content in rawtext after *and incl.* a matching text
+            before_index = rawtext.find(before_text)
+            if before_index < 0:
+                raise self.severe('Problem with "end-before" option of "%s" '
+                                  'directive:\nText not found.' % self.name)
+            rawtext = rawtext[:before_index]
+
+        include_lines = statemachine.string2lines(rawtext, tab_width,
+                                                  convert_whitespace=True)
+        if 'literal' in self.options:
+            # Convert tabs to spaces, if `tab_width` is positive.
+            if tab_width >= 0:
+                text = rawtext.expandtabs(tab_width)
+            else:
+                text = rawtext
+            literal_block = nodes.literal_block(rawtext, source=path,
+                                    classes=self.options.get('class', []))
+            literal_block.line = 1
+            self.add_name(literal_block)
+            if 'number-lines' in self.options:
+                try:
+                    startline = int(self.options['number-lines'] or 1)
+                except ValueError:
+                    raise self.error(':number-lines: with non-integer '
+                                     'start value')
+                endline = startline + len(include_lines)
+                if text.endswith('\n'):
+                    text = text[:-1]
+                tokens = NumberLines([([], text)], startline, endline)
+                for classes, value in tokens:
+                    if classes:
+                        literal_block += nodes.inline(value, value,
+                                                      classes=classes)
+                    else:
+                        literal_block += nodes.Text(value, value)
+            else:
+                literal_block += nodes.Text(text, text)
+            return [literal_block]
+        if 'code' in self.options:
+            self.options['source'] = path
+            codeblock = CodeBlock(self.name,
+                                  [self.options.pop('code')], # arguments
+                                  self.options,
+                                  include_lines, # content
+                                  self.lineno,
+                                  self.content_offset,
+                                  self.block_text,
+                                  self.state,
+                                  self.state_machine)
+            return codeblock.run()
+        self.state_machine.insert_input(include_lines, path)
+        return []

Documentation/sphinx/kerneldoc.py

@@ -0,0 +1,146 @@
+# coding=utf-8
+#
+# Copyright © 2016 Intel Corporation
+#
+# Permission is hereby granted, free of charge, to any person obtaining a
+# copy of this software and associated documentation files (the "Software"),
+# to deal in the Software without restriction, including without limitation
+# the rights to use, copy, modify, merge, publish, distribute, sublicense,
+# and/or sell copies of the Software, and to permit persons to whom the
+# Software is furnished to do so, subject to the following conditions:
+#
+# The above copyright notice and this permission notice (including the next
+# paragraph) shall be included in all copies or substantial portions of the
+# Software.
+#
+# THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+# IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+# FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
+# THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+# LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+# FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS
+# IN THE SOFTWARE.
+#
+# Authors:
+#    Jani Nikula <jani.nikula@intel.com>
+#
+# Please make sure this works on both python2 and python3.
+#
+
+import codecs
+import os
+import subprocess
+import sys
+import re
+import glob
+
+from docutils import nodes, statemachine
+from docutils.statemachine import ViewList
+from docutils.parsers.rst import directives, Directive
+from sphinx.ext.autodoc import AutodocReporter
+
+__version__  = '1.0'
+
+class KernelDocDirective(Directive):
+    """Extract kernel-doc comments from the specified file"""
+    required_argument = 1
+    optional_arguments = 4
+    option_spec = {
+        'doc': directives.unchanged_required,
+        'functions': directives.unchanged_required,
+        'export': directives.unchanged,
+        'internal': directives.unchanged,
+    }
+    has_content = False
+
+    def run(self):
+        env = self.state.document.settings.env
+        cmd = [env.config.kerneldoc_bin, '-rst', '-enable-lineno']
+
+        filename = env.config.kerneldoc_srctree + '/' + self.arguments[0]
+        export_file_patterns = []
+
+        # Tell sphinx of the dependency
+        env.note_dependency(os.path.abspath(filename))
+
+        tab_width = self.options.get('tab-width', self.state.document.settings.tab_width)
+
+        # FIXME: make this nicer and more robust against errors
+        if 'export' in self.options:
+            cmd += ['-export']
+            export_file_patterns = str(self.options.get('export')).split()
+        elif 'internal' in self.options:
+            cmd += ['-internal']
+            export_file_patterns = str(self.options.get('internal')).split()
+        elif 'doc' in self.options:
+            cmd += ['-function', str(self.options.get('doc'))]
+        elif 'functions' in self.options:
+            for f in str(self.options.get('functions')).split():
+                cmd += ['-function', f]
+
+        for pattern in export_file_patterns:
+            for f in glob.glob(env.config.kerneldoc_srctree + '/' + pattern):
+                env.note_dependency(os.path.abspath(f))
+                cmd += ['-export-file', f]
+
+        cmd += [filename]
+
+        try:
+            env.app.verbose('calling kernel-doc \'%s\'' % (" ".join(cmd)))
+
+            p = subprocess.Popen(cmd, stdout=subprocess.PIPE, stderr=subprocess.PIPE)
+            out, err = p.communicate()
+
+            out, err = codecs.decode(out, 'utf-8'), codecs.decode(err, 'utf-8')
+
+            if p.returncode != 0:
+                sys.stderr.write(err)
+
+                env.app.warn('kernel-doc \'%s\' failed with return code %d' % (" ".join(cmd), p.returncode))
+                return [nodes.error(None, nodes.paragraph(text = "kernel-doc missing"))]
+            elif env.config.kerneldoc_verbosity > 0:
+                sys.stderr.write(err)
+
+            lines = statemachine.string2lines(out, tab_width, convert_whitespace=True)
+            result = ViewList()
+
+            lineoffset = 0;
+            line_regex = re.compile("^#define LINENO ([0-9]+)$")
+            for line in lines:
+                match = line_regex.search(line)
+                if match:
+                    # sphinx counts lines from 0
+                    lineoffset = int(match.group(1)) - 1
+                    # we must eat our comments since the upset the markup
+                else:
+                    result.append(line, filename, lineoffset)
+                    lineoffset += 1
+
+            node = nodes.section()
+            buf = self.state.memo.title_styles, self.state.memo.section_level, self.state.memo.reporter
+            self.state.memo.reporter = AutodocReporter(result, self.state.memo.reporter)
+            self.state.memo.title_styles, self.state.memo.section_level = [], 0
+            try:
+                self.state.nested_parse(result, 0, node, match_titles=1)
+            finally:
+                self.state.memo.title_styles, self.state.memo.section_level, self.state.memo.reporter = buf
+
+            return node.children
+
+        except Exception as e:  # pylint: disable=W0703
+            env.app.warn('kernel-doc \'%s\' processing failed with: %s' %
+                         (" ".join(cmd), str(e)))
+            return [nodes.error(None, nodes.paragraph(text = "kernel-doc missing"))]
+
+def setup(app):
+    app.add_config_value('kerneldoc_bin', None, 'env')
+    app.add_config_value('kerneldoc_srctree', None, 'env')
+    app.add_config_value('kerneldoc_verbosity', 1, 'env')
+
+    app.add_directive('kernel-doc', KernelDocDirective)
+
+    return dict(
+        version = __version__,
+        parallel_read_safe = True,
+        parallel_write_safe = True
+    )

Documentation/sphinx/kfigure.py

@@ -0,0 +1,551 @@
+# -*- coding: utf-8; mode: python -*-
+# pylint: disable=C0103, R0903, R0912, R0915
+u"""
+    scalable figure and image handling
+    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+    Sphinx extension which implements scalable image handling.
+
+    :copyright:  Copyright (C) 2016  Markus Heiser
+    :license:    GPL Version 2, June 1991 see Linux/COPYING for details.
+
+    The build for image formats depend on image's source format and output's
+    destination format. This extension implement methods to simplify image
+    handling from the author's POV. Directives like ``kernel-figure`` implement
+    methods *to* always get the best output-format even if some tools are not
+    installed. For more details take a look at ``convert_image(...)`` which is
+    the core of all conversions.
+
+    * ``.. kernel-image``: for image handling / a ``.. image::`` replacement
+
+    * ``.. kernel-figure``: for figure handling / a ``.. figure::`` replacement
+
+    * ``.. kernel-render``: for render markup / a concept to embed *render*
+      markups (or languages). Supported markups (see ``RENDER_MARKUP_EXT``)
+
+      - ``DOT``: render embedded Graphviz's **DOC**
+      - ``SVG``: render embedded Scalable Vector Graphics (**SVG**)
+      - ... *developable*
+
+    Used tools:
+
+    * ``dot(1)``: Graphviz (http://www.graphviz.org). If Graphviz is not
+      available, the DOT language is inserted as literal-block.
+
+    * SVG to PDF: To generate PDF, you need at least one of this tools:
+
+      - ``convert(1)``: ImageMagick (https://www.imagemagick.org)
+
+    List of customizations:
+
+    * generate PDF from SVG / used by PDF (LaTeX) builder
+
+    * generate SVG (html-builder) and PDF (latex-builder) from DOT files.
+      DOT: see http://www.graphviz.org/content/dot-language
+
+    """
+
+import os
+from os import path
+import subprocess
+from hashlib import sha1
+import sys
+
+from docutils import nodes
+from docutils.statemachine import ViewList
+from docutils.parsers.rst import directives
+from docutils.parsers.rst.directives import images
+import sphinx
+
+from sphinx.util.nodes import clean_astext
+from six import iteritems
+
+PY3 = sys.version_info[0] == 3
+
+if PY3:
+    _unicode = str
+else:
+    _unicode = unicode
+
+# Get Sphinx version
+major, minor, patch = sphinx.version_info[:3]
+if major == 1 and minor > 3:
+    # patches.Figure only landed in Sphinx 1.4
+    from sphinx.directives.patches import Figure  # pylint: disable=C0413
+else:
+    Figure = images.Figure
+
+__version__  = '1.0.0'
+
+# simple helper
+# -------------
+
+def which(cmd):
+    """Searches the ``cmd`` in the ``PATH`` environment.
+
+    This *which* searches the PATH for executable ``cmd`` . First match is
+    returned, if nothing is found, ``None` is returned.
+    """
+    envpath = os.environ.get('PATH', None) or os.defpath
+    for folder in envpath.split(os.pathsep):
+        fname = folder + os.sep + cmd
+        if path.isfile(fname):
+            return fname
+
+def mkdir(folder, mode=0o775):
+    if not path.isdir(folder):
+        os.makedirs(folder, mode)
+
+def file2literal(fname):
+    with open(fname, "r") as src:
+        data = src.read()
+        node = nodes.literal_block(data, data)
+    return node
+
+def isNewer(path1, path2):
+    """Returns True if ``path1`` is newer than ``path2``
+
+    If ``path1`` exists and is newer than ``path2`` the function returns
+    ``True`` is returned otherwise ``False``
+    """
+    return (path.exists(path1)
+            and os.stat(path1).st_ctime > os.stat(path2).st_ctime)
+
+def pass_handle(self, node):           # pylint: disable=W0613
+    pass
+
+# setup conversion tools and sphinx extension
+# -------------------------------------------
+
+# Graphviz's dot(1) support
+dot_cmd = None
+
+# ImageMagick' convert(1) support
+convert_cmd = None
+
+
+def setup(app):
+    # check toolchain first
+    app.connect('builder-inited', setupTools)
+
+    # image handling
+    app.add_directive("kernel-image",  KernelImage)
+    app.add_node(kernel_image,
+                 html    = (visit_kernel_image, pass_handle),
+                 latex   = (visit_kernel_image, pass_handle),
+                 texinfo = (visit_kernel_image, pass_handle),
+                 text    = (visit_kernel_image, pass_handle),
+                 man     = (visit_kernel_image, pass_handle), )
+
+    # figure handling
+    app.add_directive("kernel-figure", KernelFigure)
+    app.add_node(kernel_figure,
+                 html    = (visit_kernel_figure, pass_handle),
+                 latex   = (visit_kernel_figure, pass_handle),
+                 texinfo = (visit_kernel_figure, pass_handle),
+                 text    = (visit_kernel_figure, pass_handle),
+                 man     = (visit_kernel_figure, pass_handle), )
+
+    # render handling
+    app.add_directive('kernel-render', KernelRender)
+    app.add_node(kernel_render,
+                 html    = (visit_kernel_render, pass_handle),
+                 latex   = (visit_kernel_render, pass_handle),
+                 texinfo = (visit_kernel_render, pass_handle),
+                 text    = (visit_kernel_render, pass_handle),
+                 man     = (visit_kernel_render, pass_handle), )
+
+    app.connect('doctree-read', add_kernel_figure_to_std_domain)
+
+    return dict(
+        version = __version__,
+        parallel_read_safe = True,
+        parallel_write_safe = True
+    )
+
+
+def setupTools(app):
+    u"""
+    Check available build tools and log some *verbose* messages.
+
+    This function is called once, when the builder is initiated.
+    """
+    global dot_cmd, convert_cmd   # pylint: disable=W0603
+    app.verbose("kfigure: check installed tools ...")
+
+    dot_cmd = which('dot')
+    convert_cmd = which('convert')
+
+    if dot_cmd:
+        app.verbose("use dot(1) from: " + dot_cmd)
+    else:
+        app.warn("dot(1) not found, for better output quality install "
+                 "graphviz from http://www.graphviz.org")
+    if convert_cmd:
+        app.verbose("use convert(1) from: " + convert_cmd)
+    else:
+        app.warn(
+            "convert(1) not found, for SVG to PDF conversion install "
+            "ImageMagick (https://www.imagemagick.org)")
+
+
+# integrate conversion tools
+# --------------------------
+
+RENDER_MARKUP_EXT = {
+    # The '.ext' must be handled by convert_image(..) function's *in_ext* input.
+    # <name> : <.ext>
+    'DOT' : '.dot',
+    'SVG' : '.svg'
+}
+
+def convert_image(img_node, translator, src_fname=None):
+    """Convert a image node for the builder.
+
+    Different builder prefer different image formats, e.g. *latex* builder
+    prefer PDF while *html* builder prefer SVG format for images.
+
+    This function handles output image formats in dependence of source the
+    format (of the image) and the translator's output format.
+    """
+    app = translator.builder.app
+
+    fname, in_ext = path.splitext(path.basename(img_node['uri']))
+    if src_fname is None:
+        src_fname = path.join(translator.builder.srcdir, img_node['uri'])
+        if not path.exists(src_fname):
+            src_fname = path.join(translator.builder.outdir, img_node['uri'])
+
+    dst_fname = None
+
+    # in kernel builds, use 'make SPHINXOPTS=-v' to see verbose messages
+
+    app.verbose('assert best format for: ' + img_node['uri'])
+
+    if in_ext == '.dot':
+
+        if not dot_cmd:
+            app.verbose("dot from graphviz not available / include DOT raw.")
+            img_node.replace_self(file2literal(src_fname))
+
+        elif translator.builder.format == 'latex':
+            dst_fname = path.join(translator.builder.outdir, fname + '.pdf')
+            img_node['uri'] = fname + '.pdf'
+            img_node['candidates'] = {'*': fname + '.pdf'}
+
+
+        elif translator.builder.format == 'html':
+            dst_fname = path.join(
+                translator.builder.outdir,
+                translator.builder.imagedir,
+                fname + '.svg')
+            img_node['uri'] = path.join(
+                translator.builder.imgpath, fname + '.svg')
+            img_node['candidates'] = {
+                '*': path.join(translator.builder.imgpath, fname + '.svg')}
+
+        else:
+            # all other builder formats will include DOT as raw
+            img_node.replace_self(file2literal(src_fname))
+
+    elif in_ext == '.svg':
+
+        if translator.builder.format == 'latex':
+            if convert_cmd is None:
+                app.verbose("no SVG to PDF conversion available / include SVG raw.")
+                img_node.replace_self(file2literal(src_fname))
+            else:
+                dst_fname = path.join(translator.builder.outdir, fname + '.pdf')
+                img_node['uri'] = fname + '.pdf'
+                img_node['candidates'] = {'*': fname + '.pdf'}
+
+    if dst_fname:
+        # the builder needs not to copy one more time, so pop it if exists.
+        translator.builder.images.pop(img_node['uri'], None)
+        _name = dst_fname[len(translator.builder.outdir) + 1:]
+
+        if isNewer(dst_fname, src_fname):
+            app.verbose("convert: {out}/%s already exists and is newer" % _name)
+
+        else:
+            ok = False
+            mkdir(path.dirname(dst_fname))
+
+            if in_ext == '.dot':
+                app.verbose('convert DOT to: {out}/' + _name)
+                ok = dot2format(app, src_fname, dst_fname)
+
+            elif in_ext == '.svg':
+                app.verbose('convert SVG to: {out}/' + _name)
+                ok = svg2pdf(app, src_fname, dst_fname)
+
+            if not ok:
+                img_node.replace_self(file2literal(src_fname))
+
+
+def dot2format(app, dot_fname, out_fname):
+    """Converts DOT file to ``out_fname`` using ``dot(1)``.
+
+    * ``dot_fname`` pathname of the input DOT file, including extension ``.dot``
+    * ``out_fname`` pathname of the output file, including format extension
+
+    The *format extension* depends on the ``dot`` command (see ``man dot``
+    option ``-Txxx``). Normally you will use one of the following extensions:
+
+    - ``.ps`` for PostScript,
+    - ``.svg`` or ``svgz`` for Structured Vector Graphics,
+    - ``.fig`` for XFIG graphics and
+    - ``.png`` or ``gif`` for common bitmap graphics.
+
+    """
+    out_format = path.splitext(out_fname)[1][1:]
+    cmd = [dot_cmd, '-T%s' % out_format, dot_fname]
+    exit_code = 42
+
+    with open(out_fname, "w") as out:
+        exit_code = subprocess.call(cmd, stdout = out)
+        if exit_code != 0:
+            app.warn("Error #%d when calling: %s" % (exit_code, " ".join(cmd)))
+    return bool(exit_code == 0)
+
+def svg2pdf(app, svg_fname, pdf_fname):
+    """Converts SVG to PDF with ``convert(1)`` command.
+
+    Uses ``convert(1)`` from ImageMagick (https://www.imagemagick.org) for
+    conversion.  Returns ``True`` on success and ``False`` if an error occurred.
+
+    * ``svg_fname`` pathname of the input SVG file with extension (``.svg``)
+    * ``pdf_name``  pathname of the output PDF file with extension (``.pdf``)
+
+    """
+    cmd = [convert_cmd, svg_fname, pdf_fname]
+    # use stdout and stderr from parent
+    exit_code = subprocess.call(cmd)
+    if exit_code != 0:
+        app.warn("Error #%d when calling: %s" % (exit_code, " ".join(cmd)))
+    return bool(exit_code == 0)
+
+
+# image handling
+# ---------------------
+
+def visit_kernel_image(self, node):    # pylint: disable=W0613
+    """Visitor of the ``kernel_image`` Node.
+
+    Handles the ``image`` child-node with the ``convert_image(...)``.
+    """
+    img_node = node[0]
+    convert_image(img_node, self)
+
+class kernel_image(nodes.image):
+    """Node for ``kernel-image`` directive."""
+    pass
+
+class KernelImage(images.Image):
+    u"""KernelImage directive
+
+    Earns everything from ``.. image::`` directive, except *remote URI* and
+    *glob* pattern. The KernelImage wraps a image node into a
+    kernel_image node. See ``visit_kernel_image``.
+    """
+
+    def run(self):
+        uri = self.arguments[0]
+        if uri.endswith('.*') or uri.find('://') != -1:
+            raise self.severe(
+                'Error in "%s: %s": glob pattern and remote images are not allowed'
+                % (self.name, uri))
+        result = images.Image.run(self)
+        if len(result) == 2 or isinstance(result[0], nodes.system_message):
+            return result
+        (image_node,) = result
+        # wrap image node into a kernel_image node / see visitors
+        node = kernel_image('', image_node)
+        return [node]
+
+# figure handling
+# ---------------------
+
+def visit_kernel_figure(self, node):   # pylint: disable=W0613
+    """Visitor of the ``kernel_figure`` Node.
+
+    Handles the ``image`` child-node with the ``convert_image(...)``.
+    """
+    img_node = node[0][0]
+    convert_image(img_node, self)
+
+class kernel_figure(nodes.figure):
+    """Node for ``kernel-figure`` directive."""
+
+class KernelFigure(Figure):
+    u"""KernelImage directive
+
+    Earns everything from ``.. figure::`` directive, except *remote URI* and
+    *glob* pattern.  The KernelFigure wraps a figure node into a kernel_figure
+    node. See ``visit_kernel_figure``.
+    """
+
+    def run(self):
+        uri = self.arguments[0]
+        if uri.endswith('.*') or uri.find('://') != -1:
+            raise self.severe(
+                'Error in "%s: %s":'
+                ' glob pattern and remote images are not allowed'
+                % (self.name, uri))
+        result = Figure.run(self)
+        if len(result) == 2 or isinstance(result[0], nodes.system_message):
+            return result
+        (figure_node,) = result
+        # wrap figure node into a kernel_figure node / see visitors
+        node = kernel_figure('', figure_node)
+        return [node]
+
+
+# render handling
+# ---------------------
+
+def visit_kernel_render(self, node):
+    """Visitor of the ``kernel_render`` Node.
+
+    If rendering tools available, save the markup of the ``literal_block`` child
+    node into a file and replace the ``literal_block`` node with a new created
+    ``image`` node, pointing to the saved markup file. Afterwards, handle the
+    image child-node with the ``convert_image(...)``.
+    """
+    app = self.builder.app
+    srclang = node.get('srclang')
+
+    app.verbose('visit kernel-render node lang: "%s"' % (srclang))
+
+    tmp_ext = RENDER_MARKUP_EXT.get(srclang, None)
+    if tmp_ext is None:
+        app.warn('kernel-render: "%s" unknown / include raw.' % (srclang))
+        return
+
+    if not dot_cmd and tmp_ext == '.dot':
+        app.verbose("dot from graphviz not available / include raw.")
+        return
+
+    literal_block = node[0]
+
+    code      = literal_block.astext()
+    hashobj   = code.encode('utf-8') #  str(node.attributes)
+    fname     = path.join('%s-%s' % (srclang, sha1(hashobj).hexdigest()))
+
+    tmp_fname = path.join(
+        self.builder.outdir, self.builder.imagedir, fname + tmp_ext)
+
+    if not path.isfile(tmp_fname):
+        mkdir(path.dirname(tmp_fname))
+        with open(tmp_fname, "w") as out:
+            out.write(code)
+
+    img_node = nodes.image(node.rawsource, **node.attributes)
+    img_node['uri'] = path.join(self.builder.imgpath, fname + tmp_ext)
+    img_node['candidates'] = {
+        '*': path.join(self.builder.imgpath, fname + tmp_ext)}
+
+    literal_block.replace_self(img_node)
+    convert_image(img_node, self, tmp_fname)
+
+
+class kernel_render(nodes.General, nodes.Inline, nodes.Element):
+    """Node for ``kernel-render`` directive."""
+    pass
+
+class KernelRender(Figure):
+    u"""KernelRender directive
+
+    Render content by external tool.  Has all the options known from the
+    *figure*  directive, plus option ``caption``.  If ``caption`` has a
+    value, a figure node with the *caption* is inserted. If not, a image node is
+    inserted.
+
+    The KernelRender directive wraps the text of the directive into a
+    literal_block node and wraps it into a kernel_render node. See
+    ``visit_kernel_render``.
+    """
+    has_content = True
+    required_arguments = 1
+    optional_arguments = 0
+    final_argument_whitespace = False
+
+    # earn options from 'figure'
+    option_spec = Figure.option_spec.copy()
+    option_spec['caption'] = directives.unchanged
+
+    def run(self):
+        return [self.build_node()]
+
+    def build_node(self):
+
+        srclang = self.arguments[0].strip()
+        if srclang not in RENDER_MARKUP_EXT.keys():
+            return [self.state_machine.reporter.warning(
+                'Unknown source language "%s", use one of: %s.' % (
+                    srclang, ",".join(RENDER_MARKUP_EXT.keys())),
+                line=self.lineno)]
+
+        code = '\n'.join(self.content)
+        if not code.strip():
+            return [self.state_machine.reporter.warning(
+                'Ignoring "%s" directive without content.' % (
+                    self.name),
+                line=self.lineno)]
+
+        node = kernel_render()
+        node['alt'] = self.options.get('alt','')
+        node['srclang'] = srclang
+        literal_node = nodes.literal_block(code, code)
+        node += literal_node
+
+        caption = self.options.get('caption')
+        if caption:
+            # parse caption's content
+            parsed = nodes.Element()
+            self.state.nested_parse(
+                ViewList([caption], source=''), self.content_offset, parsed)
+            caption_node = nodes.caption(
+                parsed[0].rawsource, '', *parsed[0].children)
+            caption_node.source = parsed[0].source
+            caption_node.line = parsed[0].line
+
+            figure_node = nodes.figure('', node)
+            for k,v in self.options.items():
+                figure_node[k] = v
+            figure_node += caption_node
+
+            node = figure_node
+
+        return node
+
+def add_kernel_figure_to_std_domain(app, doctree):
+    """Add kernel-figure anchors to 'std' domain.
+
+    The ``StandardDomain.process_doc(..)`` method does not know how to resolve
+    the caption (label) of ``kernel-figure`` directive (it only knows about
+    standard nodes, e.g. table, figure etc.). Without any additional handling
+    this will result in a 'undefined label' for kernel-figures.
+
+    This handle adds labels of kernel-figure to the 'std' domain labels.
+    """
+
+    std = app.env.domains["std"]
+    docname = app.env.docname
+    labels = std.data["labels"]
+
+    for name, explicit in iteritems(doctree.nametypes):
+        if not explicit:
+            continue
+        labelid = doctree.nameids[name]
+        if labelid is None:
+            continue
+        node = doctree.ids[labelid]
+
+        if node.tagname == 'kernel_figure':
+            for n in node.next_node():
+                if n.tagname == 'caption':
+                    sectname = clean_astext(n)
+                    # add label to std domain
+                    labels[name] = docname, labelid, sectname
+                    break

Documentation/sphinx/load_config.py

@@ -0,0 +1,32 @@
+# -*- coding: utf-8; mode: python -*-
+# pylint: disable=R0903, C0330, R0914, R0912, E0401
+
+import os
+import sys
+from sphinx.util.pycompat import execfile_
+
+# ------------------------------------------------------------------------------
+def loadConfig(namespace):
+# ------------------------------------------------------------------------------
+
+    u"""Load an additional configuration file into *namespace*.
+
+    The name of the configuration file is taken from the environment
+    ``SPHINX_CONF``. The external configuration file extends (or overwrites) the
+    configuration values from the origin ``conf.py``.  With this you are able to
+    maintain *build themes*.  """
+
+    config_file = os.environ.get("SPHINX_CONF", None)
+    if (config_file is not None
+        and os.path.normpath(namespace["__file__"]) != os.path.normpath(config_file) ):
+        config_file = os.path.abspath(config_file)
+
+        if os.path.isfile(config_file):
+            sys.stdout.write("load additional sphinx-config: %s\n" % config_file)
+            config = namespace.copy()
+            config['__file__'] = config_file
+            execfile_(config_file, config)
+            del config['__file__']
+            namespace.update(config)
+        else:
+            sys.stderr.write("WARNING: additional sphinx-config not found: %s\n" % config_file)

Documentation/sphinx/parse-headers.pl

@@ -0,0 +1,401 @@
+#!/usr/bin/perl
+use strict;
+use Text::Tabs;
+use Getopt::Long;
+use Pod::Usage;
+
+my $debug;
+my $help;
+my $man;
+
+GetOptions(
+	"debug" => \$debug,
+	'usage|?' => \$help,
+	'help' => \$man
+) or pod2usage(2);
+
+pod2usage(1) if $help;
+pod2usage(-exitstatus => 0, -verbose => 2) if $man;
+pod2usage(2) if (scalar @ARGV < 2 || scalar @ARGV > 3);
+
+my ($file_in, $file_out, $file_exceptions) = @ARGV;
+
+my $data;
+my %ioctls;
+my %defines;
+my %typedefs;
+my %enums;
+my %enum_symbols;
+my %structs;
+
+require Data::Dumper if ($debug);
+
+#
+# read the file and get identifiers
+#
+
+my $is_enum = 0;
+my $is_comment = 0;
+open IN, $file_in or die "Can't open $file_in";
+while (<IN>) {
+	$data .= $_;
+
+	my $ln = $_;
+	if (!$is_comment) {
+		$ln =~ s,/\*.*(\*/),,g;
+
+		$is_comment = 1 if ($ln =~ s,/\*.*,,);
+	} else {
+		if ($ln =~ s,^(.*\*/),,) {
+			$is_comment = 0;
+		} else {
+			next;
+		}
+	}
+
+	if ($is_enum && $ln =~ m/^\s*([_\w][\w\d_]+)\s*[\,=]?/) {
+		my $s = $1;
+		my $n = $1;
+		$n =~ tr/A-Z/a-z/;
+		$n =~ tr/_/-/;
+
+		$enum_symbols{$s} =  "\\ :ref:`$s <$n>`\\ ";
+
+		$is_enum = 0 if ($is_enum && m/\}/);
+		next;
+	}
+	$is_enum = 0 if ($is_enum && m/\}/);
+
+	if ($ln =~ m/^\s*#\s*define\s+([_\w][\w\d_]+)\s+_IO/) {
+		my $s = $1;
+		my $n = $1;
+		$n =~ tr/A-Z/a-z/;
+
+		$ioctls{$s} = "\\ :ref:`$s <$n>`\\ ";
+		next;
+	}
+
+	if ($ln =~ m/^\s*#\s*define\s+([_\w][\w\d_]+)\s+/) {
+		my $s = $1;
+		my $n = $1;
+		$n =~ tr/A-Z/a-z/;
+		$n =~ tr/_/-/;
+
+		$defines{$s} = "\\ :ref:`$s <$n>`\\ ";
+		next;
+	}
+
+	if ($ln =~ m/^\s*typedef\s+([_\w][\w\d_]+)\s+(.*)\s+([_\w][\w\d_]+);/) {
+		my $s = $2;
+		my $n = $3;
+
+		$typedefs{$n} = "\\ :c:type:`$n <$s>`\\ ";
+		next;
+	}
+	if ($ln =~ m/^\s*enum\s+([_\w][\w\d_]+)\s+\{/
+	    || $ln =~ m/^\s*enum\s+([_\w][\w\d_]+)$/
+	    || $ln =~ m/^\s*typedef\s*enum\s+([_\w][\w\d_]+)\s+\{/
+	    || $ln =~ m/^\s*typedef\s*enum\s+([_\w][\w\d_]+)$/) {
+		my $s = $1;
+
+		$enums{$s} =  "enum :c:type:`$s`\\ ";
+
+		$is_enum = $1;
+		next;
+	}
+	if ($ln =~ m/^\s*struct\s+([_\w][\w\d_]+)\s+\{/
+	    || $ln =~ m/^\s*struct\s+([[_\w][\w\d_]+)$/
+	    || $ln =~ m/^\s*typedef\s*struct\s+([_\w][\w\d_]+)\s+\{/
+	    || $ln =~ m/^\s*typedef\s*struct\s+([[_\w][\w\d_]+)$/
+	    ) {
+		my $s = $1;
+
+		$structs{$s} = "struct :c:type:`$s`\\ ";
+		next;
+	}
+}
+close IN;
+
+#
+# Handle multi-line typedefs
+#
+
+my @matches = ($data =~ m/typedef\s+struct\s+\S+?\s*\{[^\}]+\}\s*(\S+)\s*\;/g,
+	       $data =~ m/typedef\s+enum\s+\S+?\s*\{[^\}]+\}\s*(\S+)\s*\;/g,);
+foreach my $m (@matches) {
+	my $s = $m;
+
+	$typedefs{$s} = "\\ :c:type:`$s`\\ ";
+	next;
+}
+
+#
+# Handle exceptions, if any
+#
+
+my %def_reftype = (
+	"ioctl"   => ":ref",
+	"define"  => ":ref",
+	"symbol"  => ":ref",
+	"typedef" => ":c:type",
+	"enum"    => ":c:type",
+	"struct"  => ":c:type",
+);
+
+if ($file_exceptions) {
+	open IN, $file_exceptions or die "Can't read $file_exceptions";
+	while (<IN>) {
+		next if (m/^\s*$/ || m/^\s*#/);
+
+		# Parsers to ignore a symbol
+
+		if (m/^ignore\s+ioctl\s+(\S+)/) {
+			delete $ioctls{$1} if (exists($ioctls{$1}));
+			next;
+		}
+		if (m/^ignore\s+define\s+(\S+)/) {
+			delete $defines{$1} if (exists($defines{$1}));
+			next;
+		}
+		if (m/^ignore\s+typedef\s+(\S+)/) {
+			delete $typedefs{$1} if (exists($typedefs{$1}));
+			next;
+		}
+		if (m/^ignore\s+enum\s+(\S+)/) {
+			delete $enums{$1} if (exists($enums{$1}));
+			next;
+		}
+		if (m/^ignore\s+struct\s+(\S+)/) {
+			delete $structs{$1} if (exists($structs{$1}));
+			next;
+		}
+		if (m/^ignore\s+symbol\s+(\S+)/) {
+			delete $enum_symbols{$1} if (exists($enum_symbols{$1}));
+			next;
+		}
+
+		# Parsers to replace a symbol
+		my ($type, $old, $new, $reftype);
+
+		if (m/^replace\s+(\S+)\s+(\S+)\s+(\S+)/) {
+			$type = $1;
+			$old = $2;
+			$new = $3;
+		} else {
+			die "Can't parse $file_exceptions: $_";
+		}
+
+		if ($new =~ m/^\:c\:(data|func|macro|type)\:\`(.+)\`/) {
+			$reftype = ":c:$1";
+			$new = $2;
+		} elsif ($new =~ m/\:ref\:\`(.+)\`/) {
+			$reftype = ":ref";
+			$new = $1;
+		} else {
+			$reftype = $def_reftype{$type};
+		}
+		$new = "$reftype:`$old <$new>`";
+
+		if ($type eq "ioctl") {
+			$ioctls{$old} = $new if (exists($ioctls{$old}));
+			next;
+		}
+		if ($type eq "define") {
+			$defines{$old} = $new if (exists($defines{$old}));
+			next;
+		}
+		if ($type eq "symbol") {
+			$enum_symbols{$old} = $new if (exists($enum_symbols{$old}));
+			next;
+		}
+		if ($type eq "typedef") {
+			$typedefs{$old} = $new if (exists($typedefs{$old}));
+			next;
+		}
+		if ($type eq "enum") {
+			$enums{$old} = $new if (exists($enums{$old}));
+			next;
+		}
+		if ($type eq "struct") {
+			$structs{$old} = $new if (exists($structs{$old}));
+			next;
+		}
+
+		die "Can't parse $file_exceptions: $_";
+	}
+}
+
+if ($debug) {
+	print Data::Dumper->Dump([\%ioctls], [qw(*ioctls)]) if (%ioctls);
+	print Data::Dumper->Dump([\%typedefs], [qw(*typedefs)]) if (%typedefs);
+	print Data::Dumper->Dump([\%enums], [qw(*enums)]) if (%enums);
+	print Data::Dumper->Dump([\%structs], [qw(*structs)]) if (%structs);
+	print Data::Dumper->Dump([\%defines], [qw(*defines)]) if (%defines);
+	print Data::Dumper->Dump([\%enum_symbols], [qw(*enum_symbols)]) if (%enum_symbols);
+}
+
+#
+# Align block
+#
+$data = expand($data);
+$data = "    " . $data;
+$data =~ s/\n/\n    /g;
+$data =~ s/\n\s+$/\n/g;
+$data =~ s/\n\s+\n/\n\n/g;
+
+#
+# Add escape codes for special characters
+#
+$data =~ s,([\_\`\*\<\>\&\\\\:\/\|\%\$\#\{\}\~\^]),\\$1,g;
+
+$data =~ s,DEPRECATED,**DEPRECATED**,g;
+
+#
+# Add references
+#
+
+my $start_delim = "[ \n\t\(\=\*\@]";
+my $end_delim = "(\\s|,|\\\\=|\\\\:|\\;|\\\)|\\}|\\{)";
+
+foreach my $r (keys %ioctls) {
+	my $s = $ioctls{$r};
+
+	$r =~ s,([\_\`\*\<\>\&\\\\:\/]),\\\\$1,g;
+
+	print "$r -> $s\n" if ($debug);
+
+	$data =~ s/($start_delim)($r)$end_delim/$1$s$3/g;
+}
+
+foreach my $r (keys %defines) {
+	my $s = $defines{$r};
+
+	$r =~ s,([\_\`\*\<\>\&\\\\:\/]),\\\\$1,g;
+
+	print "$r -> $s\n" if ($debug);
+
+	$data =~ s/($start_delim)($r)$end_delim/$1$s$3/g;
+}
+
+foreach my $r (keys %enum_symbols) {
+	my $s = $enum_symbols{$r};
+
+	$r =~ s,([\_\`\*\<\>\&\\\\:\/]),\\\\$1,g;
+
+	print "$r -> $s\n" if ($debug);
+
+	$data =~ s/($start_delim)($r)$end_delim/$1$s$3/g;
+}
+
+foreach my $r (keys %enums) {
+	my $s = $enums{$r};
+
+	$r =~ s,([\_\`\*\<\>\&\\\\:\/]),\\\\$1,g;
+
+	print "$r -> $s\n" if ($debug);
+
+	$data =~ s/enum\s+($r)$end_delim/$s$2/g;
+}
+
+foreach my $r (keys %structs) {
+	my $s = $structs{$r};
+
+	$r =~ s,([\_\`\*\<\>\&\\\\:\/]),\\\\$1,g;
+
+	print "$r -> $s\n" if ($debug);
+
+	$data =~ s/struct\s+($r)$end_delim/$s$2/g;
+}
+
+foreach my $r (keys %typedefs) {
+	my $s = $typedefs{$r};
+
+	$r =~ s,([\_\`\*\<\>\&\\\\:\/]),\\\\$1,g;
+
+	print "$r -> $s\n" if ($debug);
+	$data =~ s/($start_delim)($r)$end_delim/$1$s$3/g;
+}
+
+$data =~ s/\\ ([\n\s])/\1/g;
+
+#
+# Generate output file
+#
+
+my $title = $file_in;
+$title =~ s,.*/,,;
+
+open OUT, "> $file_out" or die "Can't open $file_out";
+print OUT ".. -*- coding: utf-8; mode: rst -*-\n\n";
+print OUT "$title\n";
+print OUT "=" x length($title);
+print OUT "\n\n.. parsed-literal::\n\n";
+print OUT $data;
+close OUT;
+
+__END__
+
+=head1 NAME
+
+parse_headers.pl - parse a C file, in order to identify functions, structs,
+enums and defines and create cross-references to a Sphinx book.
+
+=head1 SYNOPSIS
+
+B<parse_headers.pl> [<options>] <C_FILE> <OUT_FILE> [<EXCEPTIONS_FILE>]
+
+Where <options> can be: --debug, --help or --man.
+
+=head1 OPTIONS
+
+=over 8
+
+=item B<--debug>
+
+Put the script in verbose mode, useful for debugging.
+
+=item B<--usage>
+
+Prints a brief help message and exits.
+
+=item B<--help>
+
+Prints a more detailed help message and exits.
+
+=back
+
+=head1 DESCRIPTION
+
+Convert a C header or source file (C_FILE), into a ReStructured Text
+included via ..parsed-literal block with cross-references for the
+documentation files that describe the API. It accepts an optional
+EXCEPTIONS_FILE with describes what elements will be either ignored or
+be pointed to a non-default reference.
+
+The output is written at the (OUT_FILE).
+
+It is capable of identifying defines, functions, structs, typedefs,
+enums and enum symbols and create cross-references for all of them.
+It is also capable of distinguish #define used for specifying a Linux
+ioctl.
+
+The EXCEPTIONS_FILE contain two rules to allow ignoring a symbol or
+to replace the default references by a custom one.
+
+Please read Documentation/doc-guide/parse-headers.rst at the Kernel's
+tree for more details.
+
+=head1 BUGS
+
+Report bugs to Mauro Carvalho Chehab <mchehab@kernel.org>
+
+=head1 COPYRIGHT
+
+Copyright (c) 2016 by Mauro Carvalho Chehab <mchehab+samsung@kernel.org>.
+
+License GPLv2: GNU GPL version 2 <http://gnu.org/licenses/gpl.html>.
+
+This is free software: you are free to change and redistribute it.
+There is NO WARRANTY, to the extent permitted by law.
+
+=cut

Documentation/sphinx/requirements.txt

@@ -0,0 +1,3 @@
+docutils==0.12
+Sphinx==1.4.9
+sphinx_rtd_theme

Documentation/sphinx/rstFlatTable.py

@@ -0,0 +1,376 @@
+#!/usr/bin/env python3
+# -*- coding: utf-8; mode: python -*-
+# pylint: disable=C0330, R0903, R0912
+
+u"""
+    flat-table
+    ~~~~~~~~~~
+
+    Implementation of the ``flat-table`` reST-directive.
+
+    :copyright:  Copyright (C) 2016  Markus Heiser
+    :license:    GPL Version 2, June 1991 see linux/COPYING for details.
+
+    The ``flat-table`` (:py:class:`FlatTable`) is a double-stage list similar to
+    the ``list-table`` with some additional features:
+
+    * *column-span*: with the role ``cspan`` a cell can be extended through
+      additional columns
+
+    * *row-span*: with the role ``rspan`` a cell can be extended through
+      additional rows
+
+    * *auto span* rightmost cell of a table row over the missing cells on the
+      right side of that table-row.  With Option ``:fill-cells:`` this behavior
+      can changed from *auto span* to *auto fill*, which automaticly inserts
+      (empty) cells instead of spanning the last cell.
+
+    Options:
+
+    * header-rows:   [int] count of header rows
+    * stub-columns:  [int] count of stub columns
+    * widths:        [[int] [int] ... ] widths of columns
+    * fill-cells:    instead of autospann missing cells, insert missing cells
+
+    roles:
+
+    * cspan: [int] additionale columns (*morecols*)
+    * rspan: [int] additionale rows (*morerows*)
+"""
+
+# ==============================================================================
+# imports
+# ==============================================================================
+
+import sys
+
+from docutils import nodes
+from docutils.parsers.rst import directives, roles
+from docutils.parsers.rst.directives.tables import Table
+from docutils.utils import SystemMessagePropagation
+
+# ==============================================================================
+# common globals
+# ==============================================================================
+
+# The version numbering follows numbering of the specification
+# (Documentation/books/kernel-doc-HOWTO).
+__version__  = '1.0'
+
+PY3 = sys.version_info[0] == 3
+PY2 = sys.version_info[0] == 2
+
+if PY3:
+    # pylint: disable=C0103, W0622
+    unicode     = str
+    basestring  = str
+
+# ==============================================================================
+def setup(app):
+# ==============================================================================
+
+    app.add_directive("flat-table", FlatTable)
+    roles.register_local_role('cspan', c_span)
+    roles.register_local_role('rspan', r_span)
+
+    return dict(
+        version = __version__,
+        parallel_read_safe = True,
+        parallel_write_safe = True
+    )
+
+# ==============================================================================
+def c_span(name, rawtext, text, lineno, inliner, options=None, content=None):
+# ==============================================================================
+    # pylint: disable=W0613
+
+    options  = options if options is not None else {}
+    content  = content if content is not None else []
+    nodelist = [colSpan(span=int(text))]
+    msglist  = []
+    return nodelist, msglist
+
+# ==============================================================================
+def r_span(name, rawtext, text, lineno, inliner, options=None, content=None):
+# ==============================================================================
+    # pylint: disable=W0613
+
+    options  = options if options is not None else {}
+    content  = content if content is not None else []
+    nodelist = [rowSpan(span=int(text))]
+    msglist  = []
+    return nodelist, msglist
+
+
+# ==============================================================================
+class rowSpan(nodes.General, nodes.Element): pass # pylint: disable=C0103,C0321
+class colSpan(nodes.General, nodes.Element): pass # pylint: disable=C0103,C0321
+# ==============================================================================
+
+# ==============================================================================
+class FlatTable(Table):
+# ==============================================================================
+
+    u"""FlatTable (``flat-table``) directive"""
+
+    option_spec = {
+        'name': directives.unchanged
+        , 'class': directives.class_option
+        , 'header-rows': directives.nonnegative_int
+        , 'stub-columns': directives.nonnegative_int
+        , 'widths': directives.positive_int_list
+        , 'fill-cells' : directives.flag }
+
+    def run(self):
+
+        if not self.content:
+            error = self.state_machine.reporter.error(
+                'The "%s" directive is empty; content required.' % self.name,
+                nodes.literal_block(self.block_text, self.block_text),
+                line=self.lineno)
+            return [error]
+
+        title, messages = self.make_title()
+        node = nodes.Element()          # anonymous container for parsing
+        self.state.nested_parse(self.content, self.content_offset, node)
+
+        tableBuilder = ListTableBuilder(self)
+        tableBuilder.parseFlatTableNode(node)
+        tableNode = tableBuilder.buildTableNode()
+        # SDK.CONSOLE()  # print --> tableNode.asdom().toprettyxml()
+        if title:
+            tableNode.insert(0, title)
+        return [tableNode] + messages
+
+
+# ==============================================================================
+class ListTableBuilder(object):
+# ==============================================================================
+
+    u"""Builds a table from a double-stage list"""
+
+    def __init__(self, directive):
+        self.directive = directive
+        self.rows      = []
+        self.max_cols  = 0
+
+    def buildTableNode(self):
+
+        colwidths    = self.directive.get_column_widths(self.max_cols)
+        if isinstance(colwidths, tuple):
+            # Since docutils 0.13, get_column_widths returns a (widths,
+            # colwidths) tuple, where widths is a string (i.e. 'auto').
+            # See https://sourceforge.net/p/docutils/patches/120/.
+            colwidths = colwidths[1]
+        stub_columns = self.directive.options.get('stub-columns', 0)
+        header_rows  = self.directive.options.get('header-rows', 0)
+
+        table = nodes.table()
+        tgroup = nodes.tgroup(cols=len(colwidths))
+        table += tgroup
+
+
+        for colwidth in colwidths:
+            colspec = nodes.colspec(colwidth=colwidth)
+            # FIXME: It seems, that the stub method only works well in the
+            # absence of rowspan (observed by the html buidler, the docutils-xml
+            # build seems OK).  This is not extraordinary, because there exists
+            # no table directive (except *this* flat-table) which allows to
+            # define coexistent of rowspan and stubs (there was no use-case
+            # before flat-table). This should be reviewed (later).
+            if stub_columns:
+                colspec.attributes['stub'] = 1
+                stub_columns -= 1
+            tgroup += colspec
+        stub_columns = self.directive.options.get('stub-columns', 0)
+
+        if header_rows:
+            thead = nodes.thead()
+            tgroup += thead
+            for row in self.rows[:header_rows]:
+                thead += self.buildTableRowNode(row)
+
+        tbody = nodes.tbody()
+        tgroup += tbody
+
+        for row in self.rows[header_rows:]:
+            tbody += self.buildTableRowNode(row)
+        return table
+
+    def buildTableRowNode(self, row_data, classes=None):
+        classes = [] if classes is None else classes
+        row = nodes.row()
+        for cell in row_data:
+            if cell is None:
+                continue
+            cspan, rspan, cellElements = cell
+
+            attributes = {"classes" : classes}
+            if rspan:
+                attributes['morerows'] = rspan
+            if cspan:
+                attributes['morecols'] = cspan
+            entry = nodes.entry(**attributes)
+            entry.extend(cellElements)
+            row += entry
+        return row
+
+    def raiseError(self, msg):
+        error =  self.directive.state_machine.reporter.error(
+            msg
+            , nodes.literal_block(self.directive.block_text
+                                  , self.directive.block_text)
+            , line = self.directive.lineno )
+        raise SystemMessagePropagation(error)
+
+    def parseFlatTableNode(self, node):
+        u"""parses the node from a :py:class:`FlatTable` directive's body"""
+
+        if len(node) != 1 or not isinstance(node[0], nodes.bullet_list):
+            self.raiseError(
+                'Error parsing content block for the "%s" directive: '
+                'exactly one bullet list expected.' % self.directive.name )
+
+        for rowNum, rowItem in enumerate(node[0]):
+            row = self.parseRowItem(rowItem, rowNum)
+            self.rows.append(row)
+        self.roundOffTableDefinition()
+
+    def roundOffTableDefinition(self):
+        u"""Round off the table definition.
+
+        This method rounds off the table definition in :py:member:`rows`.
+
+        * This method inserts the needed ``None`` values for the missing cells
+        arising from spanning cells over rows and/or columns.
+
+        * recount the :py:member:`max_cols`
+
+        * Autospan or fill (option ``fill-cells``) missing cells on the right
+          side of the table-row
+        """
+
+        y = 0
+        while y < len(self.rows):
+            x = 0
+
+            while x < len(self.rows[y]):
+                cell = self.rows[y][x]
+                if cell is None:
+                    x += 1
+                    continue
+                cspan, rspan = cell[:2]
+                # handle colspan in current row
+                for c in range(cspan):
+                    try:
+                        self.rows[y].insert(x+c+1, None)
+                    except: # pylint: disable=W0702
+                        # the user sets ambiguous rowspans
+                        pass # SDK.CONSOLE()
+                # handle colspan in spanned rows
+                for r in range(rspan):
+                    for c in range(cspan + 1):
+                        try:
+                            self.rows[y+r+1].insert(x+c, None)
+                        except: # pylint: disable=W0702
+                            # the user sets ambiguous rowspans
+                            pass # SDK.CONSOLE()
+                x += 1
+            y += 1
+
+        # Insert the missing cells on the right side. For this, first
+        # re-calculate the max columns.
+
+        for row in self.rows:
+            if self.max_cols < len(row):
+                self.max_cols = len(row)
+
+        # fill with empty cells or cellspan?
+
+        fill_cells = False
+        if 'fill-cells' in self.directive.options:
+            fill_cells = True
+
+        for row in self.rows:
+            x =  self.max_cols - len(row)
+            if x and not fill_cells:
+                if row[-1] is None:
+                    row.append( ( x - 1, 0, []) )
+                else:
+                    cspan, rspan, content = row[-1]
+                    row[-1] = (cspan + x, rspan, content)
+            elif x and fill_cells:
+                for i in range(x):
+                    row.append( (0, 0, nodes.comment()) )
+
+    def pprint(self):
+        # for debugging
+        retVal = "[   "
+        for row in self.rows:
+            retVal += "[ "
+            for col in row:
+                if col is None:
+                    retVal += ('%r' % col)
+                    retVal += "\n    , "
+                else:
+                    content = col[2][0].astext()
+                    if len (content) > 30:
+                        content = content[:30] + "..."
+                    retVal += ('(cspan=%s, rspan=%s, %r)'
+                               % (col[0], col[1], content))
+                    retVal += "]\n    , "
+            retVal = retVal[:-2]
+            retVal += "]\n  , "
+        retVal = retVal[:-2]
+        return retVal + "]"
+
+    def parseRowItem(self, rowItem, rowNum):
+        row = []
+        childNo = 0
+        error   = False
+        cell    = None
+        target  = None
+
+        for child in rowItem:
+            if (isinstance(child , nodes.comment)
+                or isinstance(child, nodes.system_message)):
+                pass
+            elif isinstance(child , nodes.target):
+                target = child
+            elif isinstance(child, nodes.bullet_list):
+                childNo += 1
+                cell = child
+            else:
+                error = True
+                break
+
+        if childNo != 1 or error:
+            self.raiseError(
+                'Error parsing content block for the "%s" directive: '
+                'two-level bullet list expected, but row %s does not '
+                'contain a second-level bullet list.'
+                % (self.directive.name, rowNum + 1))
+
+        for cellItem in cell:
+            cspan, rspan, cellElements = self.parseCellItem(cellItem)
+            if target is not None:
+                cellElements.insert(0, target)
+            row.append( (cspan, rspan, cellElements) )
+        return row
+
+    def parseCellItem(self, cellItem):
+        # search and remove cspan, rspan colspec from the first element in
+        # this listItem (field).
+        cspan = rspan = 0
+        if not len(cellItem):
+            return cspan, rspan, []
+        for elem in cellItem[0]:
+            if isinstance(elem, colSpan):
+                cspan = elem.get("span")
+                elem.parent.remove(elem)
+                continue
+            if isinstance(elem, rowSpan):
+                rspan = elem.get("span")
+                elem.parent.remove(elem)
+                continue
+        return cspan, rspan, cellItem[:]

Kconfig

@@ -68,25 +68,25 @@ config CC_COVERAGE
 
 config DISTRO_DEFAULTS
 	bool "Select defaults suitable for booting general purpose Linux distributions"
-	imply USE_BOOTCOMMAND
-	select CMD_BOOTZ if ARM && !ARM64
+	select AUTO_COMPLETE
+	select CMDLINE_EDITING
 	select CMD_BOOTI if ARM64
+	select CMD_BOOTZ if ARM && !ARM64
 	select CMD_DHCP if CMD_NET
-	select CMD_PING if CMD_NET
-	select CMD_PXE if NET
 	select CMD_ENV_EXISTS
 	select CMD_EXT2
 	select CMD_EXT4
 	select CMD_FAT
 	select CMD_FS_GENERIC
-	imply CMD_MII if NET
 	select CMD_PART if PARTITIONS
-	select HUSH_PARSER
-	select CMDLINE_EDITING
-	select AUTO_COMPLETE
-	select SYS_LONGHELP
-	select SUPPORT_RAW_INITRD
+	select CMD_PING if CMD_NET
+	select CMD_PXE if NET
 	select ENV_VARS_UBOOT_CONFIG
+	select HUSH_PARSER
+	select SUPPORT_RAW_INITRD
+	select SYS_LONGHELP
+	imply CMD_MII if NET
+	imply USE_BOOTCOMMAND
 	help
 	  Select this to enable various options and commands which are suitable
 	  for building u-boot for booting general purpose Linux distributions.
@@ -237,8 +237,8 @@ if FIT
 
 config FIT_ENABLE_SHA256_SUPPORT
 	bool "Support SHA256 checksum of FIT image contents"
-	select SHA256
 	default y
+	select SHA256
 	help
 	  Enable this to support SHA256 checksum of FIT image contents. A
 	  SHA256 checksum is a 256-bit (32-byte) hash value used to check that
@@ -252,8 +252,8 @@ config FIT_ENABLE_SHA256_SUPPORT
 config FIT_SIGNATURE
 	bool "Enable signature verification of FIT uImages"
 	depends on DM
-	select RSA
 	select HASH
+	select RSA
 	help
 	  This option enables signature verification of FIT uImages,
 	  using a hash signed and verified using RSA. If
@@ -267,6 +267,16 @@ config FIT_SIGNATURE
 	  format support in this case, enable it using
 	  CONFIG_IMAGE_FORMAT_LEGACY.
 
+config FIT_SIGNATURE_MAX_SIZE
+	hex "Max size of signed FIT structures"
+	depends on FIT_SIGNATURE
+	default 0x10000000
+	help
+	  This option sets a max size in bytes for verified FIT uImages.
+	  A sane value of 256MB protects corrupted DTB structures from overlapping
+	  device memory. Assure this size does not extend past expected storage
+	  space.
+
 config FIT_VERBOSE
 	bool "Show verbose messages when FIT images fail"
 	help

MAINTAINERS

@@ -107,6 +107,16 @@ F:	drivers/video/bcm2835.c
 F:	include/dm/platform_data/serial_bcm283x_mu.h
 F:	drivers/pinctrl/broadcom/
 
+ARM BROADCOM BCMSTB
+M:	Thomas Fitzsimmons <fitzsim@fitzsim.org>
+S:	Maintained
+F:	arch/arm/mach-bcmstb/
+F:	board/broadcom/bcmstb/
+F:	configs/bcm7445_defconfig
+F:	doc/README.bcm7xxx
+F:	drivers/mmc/bcmstb_sdhci.c
+F:	drivers/spi/bcmstb_spi.c
+
 ARM FREESCALE IMX
 M:	Stefano Babic <sbabic@denx.de>
 M:	Fabio Estevam <fabio.estevam@nxp.com>
@@ -145,6 +155,15 @@ T:	git git://git.denx.de/u-boot-pxa.git
 F:	arch/arm/cpu/pxa/
 F:	arch/arm/include/asm/arch-pxa/
 
+ARM OWL
+M:	Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
+S:	Maintained
+F:	arch/arm/include/asm/arch-owl/
+F:	arch/arm/mach-owl/
+F:	board/ucRobotics/
+F:	drivers/clk/owl/
+F:	drivers/serial/serial_owl.c
+
 ARM RENESAS RMOBILE/R-CAR
 M:	Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
 M:	Marek Vasut <marek.vasut+renesas@gmail.com>
@@ -187,6 +206,7 @@ ARM SNAPDRAGON
 M:	Ramon Fried <ramon.fried@gmail.com>
 S:	Maintained
 F:	arch/arm/mach-snapdragon/
+F:	drivers/smem/msm_smem.c
 
 ARM STI
 M:	Patrice Chotard <patrice.chotard@st.com>
@@ -348,6 +368,7 @@ F:	doc/README.iscsi
 F:	include/efi*
 F:	include/pe.h
 F:	include/asm-generic/pe.h
+F:	lib/charset.c
 F:	lib/efi*/
 F:	test/py/tests/test_efi*
 F:	cmd/bootefi.c
@@ -400,6 +421,7 @@ F:	drivers/net/xilinx_axi_emac.c
 F:	drivers/net/xilinx_emaclite.c
 F:	drivers/serial/serial_xuartlite.c
 F:	drivers/spi/xilinx_spi.c
+F:	drivers/sysreset/sysreset_gpio.c
 F:	drivers/watchdog/xilinx_tb_wdt.c
 N:	xilinx
 
@@ -416,8 +438,8 @@ T:	git git://git.denx.de/u-boot-mmc.git
 F:	drivers/mmc/
 
 NAND FLASH
-M:	Scott Wood <oss@buserror.net>
-S:	Maintained
+#M:	Scott Wood <oss@buserror.net>
+S:	Orphaned (Since 2018-07)
 T:	git git://git.denx.de/u-boot-nand-flash.git
 F:	drivers/mtd/nand/
 

Makefile

@@ -1,9 +1,9 @@
 # SPDX-License-Identifier: GPL-2.0+
 
 VERSION = 2018
-PATCHLEVEL = 07
+PATCHLEVEL = 09
 SUBLEVEL =
-EXTRAVERSION =
+EXTRAVERSION = -rc1
 NAME =
 
 # *DOCUMENTATION*
@@ -1053,11 +1053,6 @@ ifndef CONFIG_SYS_UBOOT_START
 CONFIG_SYS_UBOOT_START := 0
 endif
 
-# Create a file containing the configuration options the image was built with
-quiet_cmd_cpp_cfg = CFG     $@
-cmd_cpp_cfg = $(CPP) -Wp,-MD,$(depfile) $(cpp_flags) $(LDPPFLAGS) -ansi \
-	-DDO_DEPS_ONLY -D__ASSEMBLY__ -x assembler-with-cpp -P -dM -E -o $@ $<
-
 # Boards with more complex image requirments can provide an .its source file
 # or a generator script
 ifneq ($(CONFIG_SPL_FIT_SOURCE),"")
@@ -1116,8 +1111,8 @@ u-boot.sha1:	u-boot.bin
 u-boot.dis:	u-boot
 		$(OBJDUMP) -d $< > $@
 
-ifdef CONFIG_TPL
-SPL_PAYLOAD := tpl/u-boot-with-tpl.bin
+ifneq ($(CONFIG_SPL_PAYLOAD),)
+SPL_PAYLOAD := $(CONFIG_SPL_PAYLOAD:"%"=%)
 else
 SPL_PAYLOAD := u-boot.bin
 endif
@@ -1239,8 +1234,9 @@ endif
 
 ifneq ($(CONFIG_TEGRA),)
 ifneq ($(CONFIG_BINMAN),)
-u-boot-dtb-tegra.bin u-boot-tegra.bin u-boot-nodtb-tegra.bin: \
-		spl/u-boot-spl u-boot.bin FORCE
+# Makes u-boot-dtb-tegra.bin u-boot-tegra.bin u-boot-nodtb-tegra.bin
+%-dtb-tegra.bin %-tegra.bin %-nodtb-tegra.bin: \
+		spl/%-spl %.bin FORCE
 	$(call if_changed,binman)
 else
 OBJCOPYFLAGS_u-boot-nodtb-tegra.bin = -O binary --pad-to=$(CONFIG_SYS_TEXT_BASE)
@@ -1608,19 +1604,18 @@ clean: rm-files := $(CLEAN_FILES)
 
 clean-dirs	:= $(foreach f,$(u-boot-alldirs),$(if $(wildcard $(srctree)/$f/Makefile),$f))
 
-clean-dirs      := $(addprefix _clean_, $(clean-dirs) doc/DocBook)
+clean-dirs      := $(addprefix _clean_, $(clean-dirs))
 
 PHONY += $(clean-dirs) clean archclean
 $(clean-dirs):
 	$(Q)$(MAKE) $(clean)=$(patsubst _clean_%,%,$@)
 
-# TODO: Do not use *.cfgtmp
 clean: $(clean-dirs)
 	$(call cmd,rmdirs)
 	$(call cmd,rmfiles)
 	@find $(if $(KBUILD_EXTMOD), $(KBUILD_EXTMOD), .) $(RCS_FIND_IGNORE) \
 		\( -name '*.[oas]' -o -name '*.ko' -o -name '.*.cmd' \
-		-o -name '*.ko.*' -o -name '*.su' -o -name '*.cfgtmp' \
+		-o -name '*.ko.*' -o -name '*.su' \
 		-o -name '.*.d' -o -name '.*.tmp' -o -name '*.mod.c' \
 		-o -name '*.lex.c' -o -name '*.tab.[ch]' \
 		-o -name '*.symtypes' -o -name 'modules.order' \
@@ -1691,7 +1686,7 @@ help:
 	@echo  '  coccicheck      - Execute static code analysis with Coccinelle'
 	@echo  ''
 	@echo  'Documentation targets:'
-	@$(MAKE) -f $(srctree)/doc/DocBook/Makefile dochelp
+	@$(MAKE) -f $(srctree)/Documentation/Makefile dochelp
 	@echo  ''
 	@echo  '  make V=0|1 [targets] 0 => quiet build (default), 1 => verbose build'
 	@echo  '  make V=2   [targets] 2 => give reason for rebuild of target'
@@ -1713,9 +1708,11 @@ tests:
 
 # Documentation targets
 # ---------------------------------------------------------------------------
-%docs: scripts_basic FORCE
-	$(Q)$(MAKE) $(build)=scripts build_docproc
-	$(Q)$(MAKE) $(build)=doc/DocBook $@
+DOC_TARGETS := xmldocs latexdocs pdfdocs htmldocs epubdocs cleandocs \
+	       linkcheckdocs dochelp refcheckdocs
+PHONY += $(DOC_TARGETS)
+$(DOC_TARGETS): scripts_basic FORCE
+	$(Q)$(MAKE) $(build)=Documentation $@
 
 endif #ifeq ($(config-targets),1)
 endif #ifeq ($(mixed-targets),1)

README

@@ -874,9 +874,6 @@ The following options need to be configured:
 		CONFIG_EFI_PARTITION   GPT partition table, common when EFI is the
 				       bootloader.  Note 2TB partition limit; see
 				       disk/part_efi.c
-		CONFIG_MTD_PARTITIONS  Memory Technology Device partition table.
-
-		If IDE or SCSI support is enabled (CONFIG_IDE or
 		CONFIG_SCSI) you must configure support for at
 		least one non-MTD partition type as well.
 
@@ -2433,17 +2430,6 @@ FIT uImage format:
 		for a more detailed description refer to doc/README.update.
 
 - MTD Support (mtdparts command, UBI support)
-		CONFIG_MTD_DEVICE
-
-		Adds the MTD device infrastructure from the Linux kernel.
-		Needed for mtdparts command support.
-
-		CONFIG_MTD_PARTITIONS
-
-		Adds the MTD partitioning infrastructure from the Linux
-		kernel. Needed for UBI support.
-
-- UBI support
 		CONFIG_MTD_UBI_WL_THRESHOLD
 		This parameter defines the maximum difference between the highest
 		erase counter value and the lowest erase counter value of eraseblocks

arch/Kconfig

@@ -10,12 +10,12 @@ choice
 
 config ARC
 	bool "ARC architecture"
+	select ARCH_EARLY_INIT_R
+	select ARC_TIMER
+	select CLK
 	select HAVE_PRIVATE_LIBGCC
 	select SUPPORT_OF_CONTROL
-	select ARCH_EARLY_INIT_R
-	select CLK
 	select TIMER
-	select ARC_TIMER
 
 config ARM
 	bool "ARM architecture"
@@ -46,10 +46,11 @@ config NDS32
 
 config NIOS2
 	bool "Nios II architecture"
-	select SUPPORT_OF_CONTROL
-	select OF_CONTROL
-	select DM
 	select CPU
+	select DM
+	select OF_CONTROL
+	select SUPPORT_OF_CONTROL
+	imply CMD_DM
 
 config PPC
 	bool "PowerPC architecture"
@@ -65,30 +66,31 @@ config RISCV
 config SANDBOX
 	bool "Sandbox"
 	select BOARD_LATE_INIT
-	select SUPPORT_OF_CONTROL
 	select DM
-	select DM_KEYBOARD
-	select DM_SPI_FLASH
-	select DM_SERIAL
-	select DM_I2C
-	select DM_SPI
 	select DM_GPIO
+	select DM_I2C
+	select DM_KEYBOARD
 	select DM_MMC
+	select DM_SERIAL
+	select DM_SPI
+	select DM_SPI_FLASH
 	select HAVE_BLOCK_DEVICE
-	select SPI
 	select LZO
+	select SPI
+	select SUPPORT_OF_CONTROL
+	imply CMD_DM
 	imply CMD_GETTIME
 	imply CMD_HASH
 	imply CMD_IO
 	imply CMD_IOTRACE
 	imply CMD_LZMADEC
+	imply CMD_SATA
+	imply CMD_SF_TEST
 	imply CRC32_VERIFY
 	imply FAT_WRITE
 	imply HASH_VERIFY
 	imply LZMA
 	imply SCSI
-	imply CMD_SATA
-	imply CMD_SF_TEST
 
 config SH
 	bool "SuperH architecture"
@@ -97,27 +99,17 @@ config SH
 config X86
 	bool "x86 architecture"
 	select CREATE_ARCH_SYMLINK
-	select HAVE_PRIVATE_LIBGCC
-	select USE_PRIVATE_LIBGCC
-	select SUPPORT_OF_CONTROL
-	select OF_CONTROL
 	select DM
 	select DM_PCI
+	select HAVE_PRIVATE_LIBGCC
+	select OF_CONTROL
 	select PCI
+	select SUPPORT_OF_CONTROL
 	select TIMER
+	select USE_PRIVATE_LIBGCC
 	select X86_TSC_TIMER
 	imply BLK
-	imply DM_ETH
-	imply DM_GPIO
-	imply DM_KEYBOARD
-	imply DM_MMC
-	imply DM_RTC
-	imply DM_SERIAL
-	imply DM_SCSI
-	imply DM_SPI
-	imply DM_SPI_FLASH
-	imply DM_USB
-	imply DM_VIDEO
+	imply CMD_DM
 	imply CMD_FPGA_LOADMK
 	imply CMD_GETTIME
 	imply CMD_IO
@@ -125,9 +117,22 @@ config X86
 	imply CMD_PCI
 	imply CMD_SF_TEST
 	imply CMD_ZBOOT
-	imply USB_HOST_ETHER
+	imply DM_ETH
+	imply DM_GPIO
+	imply DM_KEYBOARD
+	imply DM_MMC
+	imply DM_RTC
+	imply DM_SCSI
+	imply DM_SERIAL
+	imply DM_SPI
+	imply DM_SPI_FLASH
+	imply DM_USB
+	imply DM_VIDEO
+	imply SYSRESET
+	imply SYSRESET_X86
 	imply USB_ETHER_ASIX
 	imply USB_ETHER_SMSC95XX
+	imply USB_HOST_ETHER
 
 config XTENSA
 	bool "Xtensa architecture"

arch/arc/Kconfig

@@ -31,36 +31,36 @@ choice
 
 config CPU_ARC750D
 	bool "ARC 750D"
-	select ARC_MMU_V2
 	depends on ISA_ARCOMPACT
+	select ARC_MMU_V2
 	help
 	  Choose this option to build an U-Boot for ARC750D CPU.
 
 config CPU_ARC770D
 	bool "ARC 770D"
-	select ARC_MMU_V3
 	depends on ISA_ARCOMPACT
+	select ARC_MMU_V3
 	help
 	  Choose this option to build an U-Boot for ARC770D CPU.
 
 config CPU_ARCEM6
 	bool "ARC EM6"
-	select ARC_MMU_ABSENT
 	depends on ISA_ARCV2
+	select ARC_MMU_ABSENT
 	help
 	  Next Generation ARC Core based on ISA-v2 ISA without MMU.
 
 config CPU_ARCHS36
 	bool "ARC HS36"
-	select ARC_MMU_ABSENT
 	depends on ISA_ARCV2
+	select ARC_MMU_ABSENT
 	help
 	  Next Generation ARC Core based on ISA-v2 ISA without MMU.
 
 config CPU_ARCHS38
 	bool "ARC HS38"
-	select ARC_MMU_V4
 	depends on ISA_ARCV2
+	select ARC_MMU_V4
 	help
 	  Next Generation ARC Core based on ISA-v2 ISA with MMU.
 

arch/arm/Kconfig

@@ -169,7 +169,7 @@ config ARM_ERRATA_833471
 	bool
 
 config ARM_ERRATA_845369
-       bool
+	bool
 
 config ARM_ERRATA_852421
 	bool
@@ -219,25 +219,25 @@ config CPU_ARM1176
 
 config CPU_V7A
 	bool
-	select HAS_VBAR
 	select HAS_THUMB2
+	select HAS_VBAR
 	select SYS_CACHE_SHIFT_6
 	imply SYS_ARM_MMU
 
 config CPU_V7M
 	bool
 	select HAS_THUMB2
-	select THUMB2_KERNEL
-	select SYS_CACHE_SHIFT_5
 	select SYS_ARM_MPU
+	select SYS_CACHE_SHIFT_5
 	select SYS_THUMB_BUILD
+	select THUMB2_KERNEL
 
 config CPU_V7R
 	bool
 	select HAS_THUMB2
-	select SYS_CACHE_SHIFT_6
-	select SYS_ARM_MPU
 	select SYS_ARM_CACHE_CP15
+	select SYS_ARM_MPU
+	select SYS_CACHE_SHIFT_6
 
 config CPU_PXA
 	bool
@@ -427,20 +427,21 @@ config ARCH_DAVINCI
 
 config KIRKWOOD
 	bool "Marvell Kirkwood"
-	select CPU_ARM926EJS
-	select BOARD_EARLY_INIT_F
 	select ARCH_MISC_INIT
+	select BOARD_EARLY_INIT_F
+	select CPU_ARM926EJS
 
 config ARCH_MVEBU
 	bool "Marvell MVEBU family (Armada XP/375/38x/3700/7K/8K)"
-	select OF_CONTROL
-	select OF_SEPARATE
 	select DM
 	select DM_ETH
 	select DM_SERIAL
 	select DM_SPI
 	select DM_SPI_FLASH
+	select OF_CONTROL
+	select OF_SEPARATE
 	select SPI
+	imply CMD_DM
 
 config TARGET_DEVKIT3250
 	bool "Support devkit3250"
@@ -463,31 +464,31 @@ config ORION5X
 
 config TARGET_SPEAR300
 	bool "Support spear300"
-	select CPU_ARM926EJS
 	select BOARD_EARLY_INIT_F
-	imply CMD_SAVES
+	select CPU_ARM926EJS
 	select PL011_SERIAL
+	imply CMD_SAVES
 
 config TARGET_SPEAR310
 	bool "Support spear310"
-	select CPU_ARM926EJS
 	select BOARD_EARLY_INIT_F
-	imply CMD_SAVES
+	select CPU_ARM926EJS
 	select PL011_SERIAL
+	imply CMD_SAVES
 
 config TARGET_SPEAR320
 	bool "Support spear320"
-	select CPU_ARM926EJS
 	select BOARD_EARLY_INIT_F
-	imply CMD_SAVES
+	select CPU_ARM926EJS
 	select PL011_SERIAL
+	imply CMD_SAVES
 
 config TARGET_SPEAR600
 	bool "Support spear600"
-	select CPU_ARM926EJS
 	select BOARD_EARLY_INIT_F
-	imply CMD_SAVES
+	select CPU_ARM926EJS
 	select PL011_SERIAL
+	imply CMD_SAVES
 
 config TARGET_STV0991
 	bool "Support stv0991"
@@ -496,16 +497,17 @@ config TARGET_STV0991
 	select DM_SERIAL
 	select DM_SPI
 	select DM_SPI_FLASH
+	select PL01X_SERIAL
 	select SPI
 	select SPI_FLASH
-	select PL01X_SERIAL
+	imply CMD_DM
 
 config TARGET_X600
 	bool "Support x600"
 	select BOARD_LATE_INIT
 	select CPU_ARM926EJS
-	select SUPPORT_SPL
 	select PL011_SERIAL
+	select SUPPORT_SPL
 
 config TARGET_WOODBURN
 	bool "Support woodburn"
@@ -528,11 +530,12 @@ config TARGET_MX35PDK
 config ARCH_BCM283X
 	bool "Broadcom BCM283X family"
 	select DM
-	select DM_SERIAL
 	select DM_GPIO
+	select DM_SERIAL
 	select OF_CONTROL
 	select PL01X_SERIAL
 	select SERIAL_SEARCH_ALL
+	imply CMD_DM
 	imply FAT_WRITE
 
 config TARGET_VEXPRESS_CA15_TC2
@@ -542,6 +545,17 @@ config TARGET_VEXPRESS_CA15_TC2
 	select CPU_V7_HAS_VIRT
 	select PL011_SERIAL
 
+config ARCH_BCMSTB
+	bool "Broadcom BCM7XXX family"
+	select CPU_V7A
+	select DM
+	select OF_CONTROL
+	select OF_PRIOR_STAGE
+	imply CMD_DM
+	help
+	  This enables support for Broadcom ARM-based set-top box
+	  chipsets, including the 7445 family of chips.
+
 config TARGET_VEXPRESS_CA5X2
 	bool "Support vexpress_ca5x2"
 	select CPU_V7A
@@ -567,13 +581,13 @@ config TARGET_BCM28155_AP
 config TARGET_BCMCYGNUS
 	bool "Support bcmcygnus"
 	select CPU_V7A
-	imply CRC32_VERIFY
+	imply BCM_SF2_ETH
+	imply BCM_SF2_ETH_GMAC
 	imply CMD_HASH
+	imply CRC32_VERIFY
 	imply FAT_WRITE
 	imply HASH_VERIFY
 	imply NETDEVICES
-	imply BCM_SF2_ETH
-	imply BCM_SF2_ETH_GMAC
 
 config TARGET_BCMNSP
 	bool "Support bcmnsp"
@@ -590,22 +604,24 @@ config TARGET_BCMNS2
 config ARCH_EXYNOS
 	bool "Samsung EXYNOS"
 	select DM
+	select DM_GPIO
 	select DM_I2C
-	select DM_SPI_FLASH
+	select DM_KEYBOARD
 	select DM_SERIAL
 	select DM_SPI
-	select DM_GPIO
-	select DM_KEYBOARD
+	select DM_SPI_FLASH
 	select SPI
+	imply CMD_DM
 	imply FAT_WRITE
 
 config ARCH_S5PC1XX
 	bool "Samsung S5PC1XX"
 	select CPU_V7A
 	select DM
-	select DM_SERIAL
 	select DM_GPIO
 	select DM_I2C
+	select DM_SERIAL
+	imply CMD_DM
 
 config ARCH_HIGHBANK
 	bool "Calxeda Highbank"
@@ -617,17 +633,18 @@ config ARCH_INTEGRATOR
 	select DM
 	select DM_SERIAL
 	select PL01X_SERIAL
+	imply CMD_DM
 
 config ARCH_KEYSTONE
 	bool "TI Keystone"
+	select CMD_POWEROFF
 	select CPU_V7A
 	select SUPPORT_SPL
-	select SYS_THUMB_BUILD
-	select CMD_POWEROFF
 	select SYS_ARCH_TIMER
+	select SYS_THUMB_BUILD
 	imply CMD_MTDPARTS
-	imply FIT
 	imply CMD_SAVES
+	imply FIT
 
 config ARCH_OMAP2PLUS
 	bool "TI OMAP2+"
@@ -650,6 +667,7 @@ config ARCH_MX8M
 	select ARM64
 	select DM
 	select SUPPORT_SPL
+	imply CMD_DM
 
 config ARCH_MX23
 	bool "NXP i.MX23 family"
@@ -673,19 +691,19 @@ config ARCH_MX31
 	select CPU_ARM1136
 
 config ARCH_MX7ULP
-        bool "NXP MX7ULP"
+	bool "NXP MX7ULP"
 	select CPU_V7A
 	select ROM_UNIFIED_SECTIONS
 	imply MXC_GPIO
 
 config ARCH_MX7
 	bool "Freescale MX7"
+	select ARCH_MISC_INIT
+	select BOARD_EARLY_INIT_F
 	select CPU_V7A
 	select SYS_FSL_HAS_SEC if SECURE_BOOT
 	select SYS_FSL_SEC_COMPAT_4
 	select SYS_FSL_SEC_LE
-	select BOARD_EARLY_INIT_F
-	select ARCH_MISC_INIT
 	imply MXC_GPIO
 
 config ARCH_MX6
@@ -699,27 +717,37 @@ config ARCH_MX6
 
 if ARCH_MX6
 config SPL_LDSCRIPT
-        default "arch/arm/mach-omap2/u-boot-spl.lds"
+	default "arch/arm/mach-omap2/u-boot-spl.lds"
 endif
 
 config ARCH_MX5
 	bool "Freescale MX5"
-	select CPU_V7A
 	select BOARD_EARLY_INIT_F
+	select CPU_V7A
 	imply MXC_GPIO
 
+config ARCH_OWL
+	bool "Actions Semi OWL SoCs"
+	select ARM64
+	select DM
+	select DM_SERIAL
+	select OF_CONTROL
+	imply CMD_DM
+
 config ARCH_QEMU
 	bool "QEMU Virtual Platform"
 	select DM
 	select DM_SERIAL
 	select OF_CONTROL
 	select PL01X_SERIAL
+	imply CMD_DM
 
 config ARCH_RMOBILE
 	bool "Renesas ARM SoCs"
+	select BOARD_EARLY_INIT_F
 	select DM
 	select DM_SERIAL
-	select BOARD_EARLY_INIT_F
+	imply CMD_DM
 	imply FAT_WRITE
 	imply SYS_THUMB_BUILD
 
@@ -734,40 +762,46 @@ config ARCH_SNAPDRAGON
 	select DM
 	select DM_GPIO
 	select DM_SERIAL
-	select SPMI
+	select MSM_SMEM
 	select OF_CONTROL
 	select OF_SEPARATE
+	select SMEM
+	select SPMI
+	imply CMD_DM
 
 config ARCH_SOCFPGA
 	bool "Altera SOCFPGA family"
 	select ARCH_EARLY_INIT_R
 	select ARCH_MISC_INIT
-	select CPU_V7A
+	select ARM64 if TARGET_SOCFPGA_STRATIX10
+	select CPU_V7A if TARGET_SOCFPGA_GEN5 || TARGET_SOCFPGA_ARRIA10
 	select DM
 	select DM_SERIAL
-	select ENABLE_ARM_SOC_BOOT0_HOOK
+	select ENABLE_ARM_SOC_BOOT0_HOOK if TARGET_SOCFPGA_GEN5 || TARGET_SOCFPGA_ARRIA10
 	select OF_CONTROL
+	select SPL_DM_RESET if DM_RESET
+	select SPL_DM_SERIAL
 	select SPL_LIBCOMMON_SUPPORT
 	select SPL_LIBDISK_SUPPORT
 	select SPL_LIBGENERIC_SUPPORT
 	select SPL_MMC_SUPPORT if DM_MMC
 	select SPL_NAND_SUPPORT if SPL_NAND_DENALI
 	select SPL_OF_CONTROL
+	select SPL_SEPARATE_BSS if TARGET_SOCFPGA_STRATIX10
 	select SPL_SERIAL_SUPPORT
-	select SPL_DM_SERIAL
 	select SPL_SPI_FLASH_SUPPORT if SPL_SPI_SUPPORT
 	select SPL_SPI_SUPPORT if DM_SPI
 	select SPL_WATCHDOG_SUPPORT
 	select SUPPORT_SPL
 	select SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION_TYPE
 	select SYS_NS16550
-	select SYS_THUMB_BUILD
+	select SYS_THUMB_BUILD if TARGET_SOCFPGA_GEN5 || TARGET_SOCFPGA_ARRIA10
+	imply CMD_DM
 	imply CMD_MTDPARTS
 	imply CRC32_VERIFY
 	imply DM_SPI
 	imply DM_SPI_FLASH
 	imply FAT_WRITE
-	imply HW_WATCHDOG
 	imply SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION
 
 config ARCH_SUNXI
@@ -788,13 +822,14 @@ config ARCH_SUNXI
 	select SPECIFY_CONSOLE_INDEX
 	select SPL_STACK_R if SPL
 	select SPL_SYS_MALLOC_SIMPLE if SPL
-	select SYS_NS16550
 	select SPL_SYS_THUMB_BUILD if !ARM64
+	select SYS_NS16550
 	select SYS_THUMB_BUILD if !ARM64
 	select USB if DISTRO_DEFAULTS
-	select USB_STORAGE if DISTRO_DEFAULTS
 	select USB_KEYBOARD if DISTRO_DEFAULTS
+	select USB_STORAGE if DISTRO_DEFAULTS
 	select USE_TINY_PRINTF
+	imply CMD_DM
 	imply CMD_GPT
 	imply DISTRO_DEFAULTS
 	imply FAT_WRITE
@@ -818,51 +853,54 @@ config ARCH_VF610
 
 config ARCH_ZYNQ
 	bool "Xilinx Zynq based platform"
-	select BOARD_LATE_INIT
-	select CPU_V7A
-	select SUPPORT_SPL
-	select OF_CONTROL
-	select SPL_BOARD_INIT if SPL
 	select BOARD_EARLY_INIT_F if WDT
-	select SPL_OF_CONTROL if SPL
+	select BOARD_LATE_INIT
+	select CLK
+	select CLK_ZYNQ
+	select CPU_V7A
 	select DM
 	select DM_ETH if NET
-	select SPL_DM if SPL
 	select DM_MMC if MMC
-	select DM_SPI
 	select DM_SERIAL
+	select DM_SPI
 	select DM_SPI_FLASH
-	select SPL_SEPARATE_BSS if SPL
 	select DM_USB if USB
-	select CLK
-	select SPL_CLK if SPL
-	select CLK_ZYNQ
+	select OF_CONTROL
 	select SPI
-	imply CMD_CLK
-	imply FAT_WRITE
-	imply CMD_SPL
+	select SPL_BOARD_INIT if SPL
+	select SPL_CLK if SPL
+	select SPL_DM if SPL
+	select SPL_OF_CONTROL if SPL
+	select SPL_SEPARATE_BSS if SPL
+	select SUPPORT_SPL
 	imply ARCH_EARLY_INIT_R
+	imply CMD_CLK
+	imply CMD_DM
+	imply CMD_SPL
+	imply FAT_WRITE
 
 config ARCH_ZYNQMP_R5
 	bool "Xilinx ZynqMP R5 based platform"
+	select CLK
 	select CPU_V7R
-	select OF_CONTROL
 	select DM
 	select DM_SERIAL
-	select CLK
+	select OF_CONTROL
+	imply CMD_DM
 
 config ARCH_ZYNQMP
 	bool "Xilinx ZynqMP based platform"
 	select ARM64
 	select BOARD_LATE_INIT
-	select DM
-	select OF_CONTROL
-	select DM_SERIAL
-	select SUPPORT_SPL
 	select CLK
+	select DM
+	select DM_SERIAL
+	select DM_USB if USB
+	select OF_CONTROL
 	select SPL_BOARD_INIT if SPL
 	select SPL_CLK if SPL
-	select DM_USB if USB
+	select SUPPORT_SPL
+	imply CMD_DM
 	imply FAT_WRITE
 
 config TEGRA
@@ -878,8 +916,8 @@ config TARGET_VEXPRESS64_AEMV8A
 config TARGET_VEXPRESS64_BASE_FVP
 	bool "Support Versatile Express ARMv8a FVP BASE model"
 	select ARM64
-	select SEMIHOSTING
 	select PL01X_SERIAL
+	select SEMIHOSTING
 
 config TARGET_VEXPRESS64_BASE_FVP_DRAM
 	bool "Support Versatile Express ARMv8a FVP BASE model booting from DRAM"
@@ -899,9 +937,9 @@ config TARGET_VEXPRESS64_JUNO
 config TARGET_LS2080A_EMU
 	bool "Support ls2080a_emu"
 	select ARCH_LS2080A
+	select ARCH_MISC_INIT
 	select ARM64
 	select ARMV8_MULTIENTRY
-	select ARCH_MISC_INIT
 	help
 	  Support for Freescale LS2080A_EMU platform
 	  The LS2080A Development System (EMULATOR) is a pre silicon
@@ -911,9 +949,9 @@ config TARGET_LS2080A_EMU
 config TARGET_LS2080A_SIMU
 	bool "Support ls2080a_simu"
 	select ARCH_LS2080A
+	select ARCH_MISC_INIT
 	select ARM64
 	select ARMV8_MULTIENTRY
-	select ARCH_MISC_INIT
 	help
 	  Support for Freescale LS2080A_SIMU platform
 	  The LS2080A Development System (QDS) is a pre silicon
@@ -923,9 +961,9 @@ config TARGET_LS2080A_SIMU
 config TARGET_LS1088AQDS
 	bool "Support ls1088aqds"
 	select ARCH_LS1088A
+	select ARCH_MISC_INIT
 	select ARM64
 	select ARMV8_MULTIENTRY
-	select ARCH_MISC_INIT
 	select BOARD_LATE_INIT
 	select SUPPORT_SPL
 	help
@@ -937,11 +975,11 @@ config TARGET_LS1088AQDS
 config TARGET_LS2080AQDS
 	bool "Support ls2080aqds"
 	select ARCH_LS2080A
+	select ARCH_MISC_INIT
 	select ARM64
 	select ARMV8_MULTIENTRY
 	select BOARD_LATE_INIT
 	select SUPPORT_SPL
-	select ARCH_MISC_INIT
 	imply SCSI
 	imply SCSI_AHCI
 	help
@@ -953,11 +991,11 @@ config TARGET_LS2080AQDS
 config TARGET_LS2080ARDB
 	bool "Support ls2080ardb"
 	select ARCH_LS2080A
+	select ARCH_MISC_INIT
 	select ARM64
 	select ARMV8_MULTIENTRY
 	select BOARD_LATE_INIT
 	select SUPPORT_SPL
-	select ARCH_MISC_INIT
 	imply SCSI
 	imply SCSI_AHCI
 	help
@@ -969,11 +1007,11 @@ config TARGET_LS2080ARDB
 config TARGET_LS2081ARDB
 	bool "Support ls2081ardb"
 	select ARCH_LS2080A
+	select ARCH_MISC_INIT
 	select ARM64
 	select ARMV8_MULTIENTRY
 	select BOARD_LATE_INIT
 	select SUPPORT_SPL
-	select ARCH_MISC_INIT
 	help
 	  Support for Freescale LS2081ARDB platform.
 	  The LS2081A Reference design board (RDB) is a high-performance
@@ -989,6 +1027,7 @@ config TARGET_HIKEY
 	select OF_CONTROL
 	select PL01X_SERIAL
 	select SPECIFY_CONSOLE_INDEX
+	imply CMD_DM
 	  help
 	  Support for HiKey 96boards platform. It features a HI6220
 	  SoC, with 8xA53 CPU, mali450 gpu, and 1GB RAM.
@@ -997,10 +1036,11 @@ config TARGET_POPLAR
 	bool "Support Poplar 96boards Enterprise Edition Platform"
 	select ARM64
 	select DM
-	select OF_CONTROL
 	select DM_SERIAL
 	select DM_USB
+	select OF_CONTROL
 	select PL01X_SERIAL
+	imply CMD_DM
 	  help
 	  Support for Poplar 96boards EE platform. It features a HI3798cv200
 	  SoC, with 4xA53 CPU, 1GB RAM and the high performance Mali T720 GPU
@@ -1046,8 +1086,8 @@ config TARGET_LS1012A2G5RDB
 config TARGET_LS1012AFRWY
 	bool "Support ls1012afrwy"
 	select ARCH_LS1012A
-	select BOARD_LATE_INIT
 	select ARM64
+	select BOARD_LATE_INIT
 	imply SCSI
 	imply SCSI_AHCI
 	help
@@ -1069,9 +1109,9 @@ config TARGET_LS1012AFRDM
 config TARGET_LS1088ARDB
 	bool "Support ls1088ardb"
 	select ARCH_LS1088A
+	select ARCH_MISC_INIT
 	select ARM64
 	select ARMV8_MULTIENTRY
-	select ARCH_MISC_INIT
 	select BOARD_LATE_INIT
 	select SUPPORT_SPL
 	help
@@ -1082,40 +1122,40 @@ config TARGET_LS1088ARDB
 
 config TARGET_LS1021AQDS
 	bool "Support ls1021aqds"
+	select ARCH_LS1021A
+	select ARCH_SUPPORT_PSCI
+	select BOARD_EARLY_INIT_F
 	select BOARD_LATE_INIT
 	select CPU_V7A
 	select CPU_V7_HAS_NONSEC
 	select CPU_V7_HAS_VIRT
-	select SUPPORT_SPL
-	select ARCH_LS1021A
-	select ARCH_SUPPORT_PSCI
 	select LS1_DEEP_SLEEP
+	select SUPPORT_SPL
 	select SYS_FSL_DDR
-	select BOARD_EARLY_INIT_F
 	imply SCSI
 
 config TARGET_LS1021ATWR
 	bool "Support ls1021atwr"
+	select ARCH_LS1021A
+	select ARCH_SUPPORT_PSCI
+	select BOARD_EARLY_INIT_F
 	select BOARD_LATE_INIT
 	select CPU_V7A
 	select CPU_V7_HAS_NONSEC
 	select CPU_V7_HAS_VIRT
-	select SUPPORT_SPL
-	select ARCH_LS1021A
-	select ARCH_SUPPORT_PSCI
 	select LS1_DEEP_SLEEP
-	select BOARD_EARLY_INIT_F
+	select SUPPORT_SPL
 	imply SCSI
 
 config TARGET_LS1021AIOT
 	bool "Support ls1021aiot"
+	select ARCH_LS1021A
+	select ARCH_SUPPORT_PSCI
 	select BOARD_LATE_INIT
 	select CPU_V7A
 	select CPU_V7_HAS_NONSEC
 	select CPU_V7_HAS_VIRT
 	select SUPPORT_SPL
-	select ARCH_LS1021A
-	select ARCH_SUPPORT_PSCI
 	imply SCSI
 	help
 	  Support for Freescale LS1021AIOT platform.
@@ -1128,9 +1168,9 @@ config TARGET_LS1043AQDS
 	select ARCH_LS1043A
 	select ARM64
 	select ARMV8_MULTIENTRY
+	select BOARD_EARLY_INIT_F
 	select BOARD_LATE_INIT
 	select SUPPORT_SPL
-	select BOARD_EARLY_INIT_F
 	imply SCSI
 	help
 	  Support for Freescale LS1043AQDS platform.
@@ -1140,9 +1180,9 @@ config TARGET_LS1043ARDB
 	select ARCH_LS1043A
 	select ARM64
 	select ARMV8_MULTIENTRY
+	select BOARD_EARLY_INIT_F
 	select BOARD_LATE_INIT
 	select SUPPORT_SPL
-	select BOARD_EARLY_INIT_F
 	imply SCSI
 	help
 	  Support for Freescale LS1043ARDB platform.
@@ -1152,10 +1192,10 @@ config TARGET_LS1046AQDS
 	select ARCH_LS1046A
 	select ARM64
 	select ARMV8_MULTIENTRY
-	select BOARD_LATE_INIT
-	select SUPPORT_SPL
-	select DM_SPI_FLASH if DM_SPI
 	select BOARD_EARLY_INIT_F
+	select BOARD_LATE_INIT
+	select DM_SPI_FLASH if DM_SPI
+	select SUPPORT_SPL
 	imply SCSI
 	help
 	  Support for Freescale LS1046AQDS platform.
@@ -1168,11 +1208,11 @@ config TARGET_LS1046ARDB
 	select ARCH_LS1046A
 	select ARM64
 	select ARMV8_MULTIENTRY
+	select BOARD_EARLY_INIT_F
 	select BOARD_LATE_INIT
-	select SUPPORT_SPL
 	select DM_SPI_FLASH if DM_SPI
 	select POWER_MC34VR500
-	select BOARD_EARLY_INIT_F
+	select SUPPORT_SPL
 	imply SCSI
 	help
 	  Support for Freescale LS1046ARDB platform.
@@ -1202,6 +1242,7 @@ config ARCH_UNIPHIER
 	select DM_RESET
 	select DM_SERIAL
 	select DM_USB
+	select OF_BOARD_SETUP
 	select OF_CONTROL
 	select OF_LIBFDT
 	select PINCTRL
@@ -1212,6 +1253,8 @@ config ARCH_UNIPHIER
 	select SPL_OF_CONTROL if SPL
 	select SPL_PINCTRL if SPL
 	select SUPPORT_SPL
+	imply CMD_DM
+	imply DISTRO_DEFAULTS
 	imply FAT_WRITE
 	help
 	  Support for UniPhier SoC family developed by Socionext Inc.
@@ -1223,15 +1266,17 @@ config STM32
 	select DM
 	select DM_SERIAL
 	select SYS_THUMB_BUILD
+	imply CMD_DM
 
 config ARCH_STI
 	bool "Support STMicrolectronics SoCs"
+	select BLK
 	select CPU_V7A
 	select DM
-	select DM_SERIAL
-	select BLK
 	select DM_MMC
 	select DM_RESET
+	select DM_SERIAL
+	imply CMD_DM
 	help
 	  Support for STMicroelectronics STiH407/10 SoC family.
 	  This SoC is used on Linaro 96Board STiH410-B2260
@@ -1245,15 +1290,16 @@ config ARCH_STM32MP
 	select DM_GPIO
 	select DM_RESET
 	select DM_SERIAL
+	select MISC
 	select OF_CONTROL
 	select OF_LIBFDT
-	select MISC
 	select PINCTRL
 	select REGMAP
 	select SUPPORT_SPL
 	select SYSCON
 	select SYSRESET
 	select SYS_THUMB_BUILD
+	imply CMD_DM
 	help
 	  Support for STM32MP SoC family developed by STMicroelectronics,
 	  MPUs based on ARM cortex A core
@@ -1262,44 +1308,46 @@ config ARCH_STM32MP
 
 config ARCH_ROCKCHIP
 	bool "Support Rockchip SoCs"
-	select OF_CONTROL
 	select BLK
 	select DM
-	select SPL_DM if SPL
-	select SYS_MALLOC_F
-	select SYS_THUMB_BUILD if !ARM64
-	select SPL_SYS_MALLOC_SIMPLE if SPL
 	select DM_GPIO
 	select DM_I2C
 	select DM_MMC
+	select DM_PWM
+	select DM_REGULATOR
 	select DM_SERIAL
 	select DM_SPI
 	select DM_SPI_FLASH
 	select DM_USB if USB
-	select DM_PWM
-	select DM_REGULATOR
 	select ENABLE_ARM_SOC_BOOT0_HOOK
+	select OF_CONTROL
 	select SPI
+	select SPL_DM if SPL
+	select SPL_SYS_MALLOC_SIMPLE if SPL
+	select SYS_MALLOC_F
+	select SYS_THUMB_BUILD if !ARM64
+	imply ADC
+	imply CMD_DM
 	imply DISTRO_DEFAULTS
 	imply FAT_WRITE
-	imply USB_FUNCTION_FASTBOOT
-	imply SPL_SYSRESET
-	imply TPL_SYSRESET
-	imply ADC
 	imply SARADC_ROCKCHIP
+	imply SPL_SYSRESET
 	imply SYS_NS16550
+	imply TPL_SYSRESET
+	imply USB_FUNCTION_FASTBOOT
 
 config TARGET_THUNDERX_88XX
 	bool "Support ThunderX 88xx"
 	select ARM64
 	select OF_CONTROL
-	select SYS_CACHE_SHIFT_7
 	select PL01X_SERIAL
+	select SYS_CACHE_SHIFT_7
 
 config ARCH_ASPEED
 	bool "Support Aspeed SoCs"
-	select OF_CONTROL
 	select DM
+	select OF_CONTROL
+	imply CMD_DM
 
 endchoice
 
@@ -1319,6 +1367,8 @@ source "arch/arm/mach-at91/Kconfig"
 
 source "arch/arm/mach-bcm283x/Kconfig"
 
+source "arch/arm/mach-bcmstb/Kconfig"
+
 source "arch/arm/mach-davinci/Kconfig"
 
 source "arch/arm/mach-exynos/Kconfig"
@@ -1357,6 +1407,8 @@ source "arch/arm/cpu/armv8/fsl-layerscape/Kconfig"
 
 source "arch/arm/mach-orion5x/Kconfig"
 
+source "arch/arm/mach-owl/Kconfig"
+
 source "arch/arm/mach-rmobile/Kconfig"
 
 source "arch/arm/mach-meson/Kconfig"
@@ -1444,12 +1496,15 @@ source "board/spear/spear600/Kconfig"
 source "board/spear/x600/Kconfig"
 source "board/st/stv0991/Kconfig"
 source "board/tcl/sl50/Kconfig"
+source "board/ucRobotics/bubblegum_96/Kconfig"
 source "board/birdland/bav335x/Kconfig"
 source "board/timll/devkit3250/Kconfig"
 source "board/toradex/colibri_pxa270/Kconfig"
 source "board/vscom/baltos/Kconfig"
 source "board/woodburn/Kconfig"
 source "board/work-microwave/work_92105/Kconfig"
+source "board/xilinx/Kconfig"
+source "board/xilinx/zynq/Kconfig"
 source "board/xilinx/zynqmp/Kconfig"
 source "board/zipitz2/Kconfig"
 
@@ -1458,8 +1513,8 @@ source "arch/arm/Kconfig.debug"
 endmenu
 
 config SPL_LDSCRIPT
-        default "arch/arm/cpu/arm926ejs/mxs/u-boot-spl.lds" if (ARCH_MX23 || ARCH_MX28) && !SPL_FRAMEWORK
-        default "arch/arm/cpu/arm1136/u-boot-spl.lds" if CPU_ARM1136
+	default "arch/arm/cpu/arm926ejs/mxs/u-boot-spl.lds" if (ARCH_MX23 || ARCH_MX28) && !SPL_FRAMEWORK
+	default "arch/arm/cpu/arm1136/u-boot-spl.lds" if CPU_ARM1136
 	default "arch/arm/cpu/armv8/u-boot-spl.lds" if ARM64
 
 

arch/arm/Makefile

@@ -54,6 +54,7 @@ PLATFORM_CPPFLAGS += $(arch-y) $(tune-y)
 machine-$(CONFIG_ARCH_ASPEED)		+= aspeed
 machine-$(CONFIG_ARCH_AT91)		+= at91
 machine-$(CONFIG_ARCH_BCM283X)		+= bcm283x
+machine-$(CONFIG_ARCH_BCMSTB)		+= bcmstb
 machine-$(CONFIG_ARCH_DAVINCI)		+= davinci
 machine-$(CONFIG_ARCH_EXYNOS)		+= exynos
 machine-$(CONFIG_ARCH_HIGHBANK)		+= highbank
@@ -66,6 +67,7 @@ machine-$(CONFIG_ARCH_MVEBU)		+= mvebu
 # TODO: rename CONFIG_ORION5X -> CONFIG_ARCH_ORION5X
 machine-$(CONFIG_ORION5X)		+= orion5x
 machine-$(CONFIG_ARCH_OMAP2PLUS)	+= omap2
+machine-$(CONFIG_ARCH_OWL)		+= owl
 machine-$(CONFIG_ARCH_S5PC1XX)		+= s5pc1xx
 machine-$(CONFIG_ARCH_SUNXI)		+= sunxi
 machine-$(CONFIG_ARCH_SNAPDRAGON)	+= snapdragon

arch/arm/config.mk

@@ -134,11 +134,11 @@ endif
 ifdef CONFIG_ARM64
 OBJCOPYFLAGS += -j .text -j .secure_text -j .secure_data -j .rodata -j .data \
 		-j .u_boot_list -j .rela.dyn -j .got -j .got.plt \
-		-j .binman_sym_table
+		-j .binman_sym_table -j .text_rest
 else
 OBJCOPYFLAGS += -j .text -j .secure_text -j .secure_data -j .rodata -j .hash \
 		-j .data -j .got -j .got.plt -j .u_boot_list -j .rel.dyn \
-		-j .binman_sym_table
+		-j .binman_sym_table -j .text_rest
 endif
 
 # if a dtb section exists we always have to include it

arch/arm/cpu/armv7/Kconfig

@@ -53,7 +53,7 @@ config ARMV7_PSCI_NR_CPUS
 config ARMV7_LPAE
 	bool "Use LPAE page table format" if EXPERT
 	depends on CPU_V7A
-	default n
+	default y if ARMV7_VIRT
 	---help---
 	Say Y here to use the long descriptor page table format. This is
 	required if U-Boot runs in HYP mode.

arch/arm/cpu/armv7/ls102xa/Kconfig

@@ -1,5 +1,7 @@
 config ARCH_LS1021A
 	bool
+	select SYS_FSL_DDR_BE if SYS_FSL_DDR
+	select SYS_FSL_DDR_VER_50 if SYS_FSL_DDR
 	select SYS_FSL_ERRATUM_A008378
 	select SYS_FSL_ERRATUM_A008407
 	select SYS_FSL_ERRATUM_A008997
@@ -10,18 +12,16 @@ config ARCH_LS1021A
 	select SYS_FSL_ERRATUM_A009942
 	select SYS_FSL_ERRATUM_A010315
 	select SYS_FSL_HAS_CCI400
-	select SYS_FSL_SRDS_1
-	select SYS_HAS_SERDES
-	select SYS_FSL_DDR_BE if SYS_FSL_DDR
-	select SYS_FSL_DDR_VER_50 if SYS_FSL_DDR
 	select SYS_FSL_HAS_DDR3 if SYS_FSL_DDR
 	select SYS_FSL_HAS_DDR4 if SYS_FSL_DDR
 	select SYS_FSL_HAS_SEC
 	select SYS_FSL_SEC_COMPAT_5
 	select SYS_FSL_SEC_LE
+	select SYS_FSL_SRDS_1
+	select SYS_HAS_SERDES
+	imply CMD_PCI
 	imply SCSI
 	imply SCSI_AHCI
-	imply CMD_PCI
 
 menu "LS102xA architecture"
 	depends on ARCH_LS1021A

arch/arm/cpu/armv7/nonsec_virt.S

@@ -80,6 +80,8 @@ _secure_monitor:
 #ifdef CONFIG_ARMV7_VIRT
 	orreq	r5, r5, #0x100			@ allow HVC instruction
 	moveq	r6, #HYP_MODE			@ Enter the kernel as HYP
+	mrseq	r3, sp_svc
+	msreq	sp_hyp, r3			@ migrate SP
 #endif
 
 	mcr	p15, 0, r5, c1, c1, 0		@ write SCR (with NS bit set)

arch/arm/cpu/armv7/psci.S

@@ -331,6 +331,8 @@ ENTRY(psci_cpu_entry)
 
 	bl	_nonsec_init
 
+	bl	psci_stack_setup
+
 	bl	psci_arch_cpu_entry
 
 	bl	psci_get_cpu_id			@ CPU ID => r0

arch/arm/cpu/armv8/Kconfig

@@ -44,8 +44,8 @@ config ARMV8_SPIN_TABLE
 menu "ARMv8 secure monitor firmware"
 config ARMV8_SEC_FIRMWARE_SUPPORT
 	bool "Enable ARMv8 secure monitor firmware framework support"
-	select OF_LIBFDT
 	select FIT
+	select OF_LIBFDT
 	help
 	  This framework is aimed at making secure monitor firmware load
 	  process brief.
@@ -60,8 +60,8 @@ config ARMV8_SEC_FIRMWARE_SUPPORT
 
 config SPL_ARMV8_SEC_FIRMWARE_SUPPORT
 	bool "Enable ARMv8 secure monitor firmware framework support for SPL"
-	select SPL_OF_LIBFDT
 	select SPL_FIT
+	select SPL_OF_LIBFDT
 	help
 	  Say Y here to support this framework in SPL phase.
 

arch/arm/cpu/armv8/fsl-layerscape/cpu.c

@@ -9,6 +9,7 @@
 #include <asm/io.h>
 #include <linux/errno.h>
 #include <asm/system.h>
+#include <fm_eth.h>
 #include <asm/armv8/mmu.h>
 #include <asm/io.h>
 #include <asm/arch/fsl_serdes.h>
@@ -18,7 +19,6 @@
 #include <fsl_immap.h>
 #include <asm/arch/mp.h>
 #include <efi_loader.h>
-#include <fm_eth.h>
 #include <fsl-mc/fsl_mc.h>
 #ifdef CONFIG_FSL_ESDHC
 #include <fsl_esdhc.h>

arch/arm/cpu/armv8/fsl-layerscape/doc/README.falcon

@@ -129,6 +129,16 @@ Example:
 
 The "loadables" is not optional. It tells SPL which images to load into memory.
 
+Falcon mode with QSPI boot
+--------------------------
+To use falcon mode with QSPI boot, SPL needs to be enabled. Similar to SD or
+NAND boot, a RAM version full feature U-Boot is needed. Unlike SD or NAND boot,
+SPL with QSPI doesn't need to combine SPL image with RAM version image. Two
+separated images are used, u-boot-spl.pbl and u-boot.img. The former is SPL
+image with RCW and PBI commands to load the SPL payload into On-Chip RAM. The
+latter is RAM version U-Boot in FIT format (or legacy format if FIT is not
+used).
+
 Other things to consider
 -----------------------
 Falcon boot skips a lot of initialization in U-Boot. If Linux expects the

arch/arm/cpu/armv8/fsl-layerscape/soc.c

@@ -6,8 +6,6 @@
 #include <common.h>
 #include <fsl_immap.h>
 #include <fsl_ifc.h>
-#include <ahci.h>
-#include <scsi.h>
 #include <asm/arch/fsl_serdes.h>
 #include <asm/arch/soc.h>
 #include <asm/io.h>
@@ -330,36 +328,6 @@ void fsl_lsch3_early_init_f(void)
 #endif
 }
 
-#ifdef CONFIG_SCSI_AHCI_PLAT
-int sata_init(void)
-{
-	struct ccsr_ahci __iomem *ccsr_ahci;
-
-#ifdef CONFIG_SYS_SATA2
-	ccsr_ahci  = (void *)CONFIG_SYS_SATA2;
-	out_le32(&ccsr_ahci->ppcfg, AHCI_PORT_PHY_1_CFG);
-	out_le32(&ccsr_ahci->pp2c, AHCI_PORT_PHY2_CFG);
-	out_le32(&ccsr_ahci->pp3c, AHCI_PORT_PHY3_CFG);
-	out_le32(&ccsr_ahci->ptc, AHCI_PORT_TRANS_CFG);
-	out_le32(&ccsr_ahci->axicc, AHCI_PORT_AXICC_CFG);
-#endif
-
-#ifdef CONFIG_SYS_SATA1
-	ccsr_ahci  = (void *)CONFIG_SYS_SATA1;
-	out_le32(&ccsr_ahci->ppcfg, AHCI_PORT_PHY_1_CFG);
-	out_le32(&ccsr_ahci->pp2c, AHCI_PORT_PHY2_CFG);
-	out_le32(&ccsr_ahci->pp3c, AHCI_PORT_PHY3_CFG);
-	out_le32(&ccsr_ahci->ptc, AHCI_PORT_TRANS_CFG);
-	out_le32(&ccsr_ahci->axicc, AHCI_PORT_AXICC_CFG);
-
-	ahci_init((void __iomem *)CONFIG_SYS_SATA1);
-	scsi_scan(false);
-#endif
-
-	return 0;
-}
-#endif
-
 /* Get VDD in the unit mV from voltage ID */
 int get_core_volt_from_fuse(void)
 {
@@ -400,25 +368,6 @@ int get_core_volt_from_fuse(void)
 }
 
 #elif defined(CONFIG_FSL_LSCH2)
-#ifdef CONFIG_SCSI_AHCI_PLAT
-int sata_init(void)
-{
-	struct ccsr_ahci __iomem *ccsr_ahci = (void *)CONFIG_SYS_SATA;
-
-	/* Disable SATA ECC */
-	out_le32((void *)CONFIG_SYS_DCSR_DCFG_ADDR + 0x520, 0x80000000);
-	out_le32(&ccsr_ahci->ppcfg, AHCI_PORT_PHY_1_CFG);
-	out_le32(&ccsr_ahci->pp2c, AHCI_PORT_PHY2_CFG);
-	out_le32(&ccsr_ahci->pp3c, AHCI_PORT_PHY3_CFG);
-	out_le32(&ccsr_ahci->ptc, AHCI_PORT_TRANS_CFG);
-	out_le32(&ccsr_ahci->axicc, AHCI_PORT_AXICC_CFG);
-
-	ahci_init((void __iomem *)CONFIG_SYS_SATA);
-	scsi_scan(false);
-
-	return 0;
-}
-#endif
 
 static void erratum_a009929(void)
 {
@@ -719,9 +668,6 @@ int qspi_ahb_init(void)
 #ifdef CONFIG_BOARD_LATE_INIT
 int board_late_init(void)
 {
-#ifdef CONFIG_SCSI_AHCI_PLAT
-	sata_init();
-#endif
 #ifdef CONFIG_CHAIN_OF_TRUST
 	fsl_setenv_chain_of_trust();
 #endif

arch/arm/cpu/armv8/fsl-layerscape/spl.c

@@ -11,6 +11,7 @@
 #include <fsl_csu.h>
 #include <asm/arch/fdt.h>
 #include <asm/arch/ppa.h>
+#include <asm/arch/soc.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -21,6 +22,9 @@ u32 spl_boot_device(void)
 #endif
 #ifdef CONFIG_SPL_NAND_SUPPORT
 	return BOOT_DEVICE_NAND;
+#endif
+#ifdef CONFIG_QSPI_BOOT
+	return BOOT_DEVICE_NOR;
 #endif
 	return 0;
 }
@@ -52,6 +56,7 @@ void spl_board_init(void)
 
 void board_init_f(ulong dummy)
 {
+	icache_enable();
 	/* Clear global data */
 	memset((void *)gd, 0, sizeof(gd_t));
 	board_early_init_f();
@@ -101,6 +106,9 @@ void board_init_f(ulong dummy)
 	gd->arch.tlb_addr = (gd->ram_top - gd->arch.tlb_size) & ~(0x10000 - 1);
 	gd->arch.tlb_allocated = gd->arch.tlb_addr;
 #endif	/* CONFIG_SPL_FSL_LS_PPA */
+#if defined(CONFIG_QSPI_AHB_INIT) && defined(CONFIG_QSPI_BOOT)
+	qspi_ahb_init();
+#endif
 }
 
 #ifdef CONFIG_SPL_OS_BOOT

arch/arm/cpu/armv8/u-boot.lds

@@ -25,6 +25,19 @@ SECTIONS
 	{
 		*(.__image_copy_start)
 		CPUDIR/start.o (.text*)
+	}
+
+	/* This needs to come before *(.text*) */
+	.efi_runtime : {
+                __efi_runtime_start = .;
+		*(.text.efi_runtime*)
+		*(.rodata.efi_runtime*)
+		*(.data.efi_runtime*)
+                __efi_runtime_stop = .;
+	}
+
+	.text_rest :
+	{
 		*(.text*)
 	}
 
@@ -98,17 +111,10 @@ SECTIONS
 
 	. = ALIGN(8);
 
-	.efi_runtime : {
-                __efi_runtime_start = .;
-		*(efi_runtime_text)
-		*(efi_runtime_data)
-                __efi_runtime_stop = .;
-	}
-
 	.efi_runtime_rel : {
                 __efi_runtime_rel_start = .;
-		*(.relaefi_runtime_text)
-		*(.relaefi_runtime_data)
+		*(.rel*.efi_runtime)
+		*(.rel*.efi_runtime.*)
                 __efi_runtime_rel_stop = .;
 	}
 

arch/arm/cpu/u-boot.lds

@@ -43,6 +43,25 @@ SECTIONS
 		*(.__image_copy_start)
 		*(.vectors)
 		CPUDIR/start.o (.text*)
+	}
+
+	/* This needs to come before *(.text*) */
+	.__efi_runtime_start : {
+		*(.__efi_runtime_start)
+	}
+
+	.efi_runtime : {
+		*(.text.efi_runtime*)
+		*(.rodata.efi_runtime*)
+		*(.data.efi_runtime*)
+	}
+
+	.__efi_runtime_stop : {
+		*(.__efi_runtime_stop)
+	}
+
+	.text_rest :
+	{
 		*(.text*)
 	}
 
@@ -136,27 +155,14 @@ SECTIONS
 
 	. = ALIGN(4);
 
-	.__efi_runtime_start : {
-		*(.__efi_runtime_start)
-	}
-
-	.efi_runtime : {
-		*(efi_runtime_text)
-		*(efi_runtime_data)
-	}
-
-	.__efi_runtime_stop : {
-		*(.__efi_runtime_stop)
-	}
-
 	.efi_runtime_rel_start :
 	{
 		*(.__efi_runtime_rel_start)
 	}
 
 	.efi_runtime_rel : {
-		*(.relefi_runtime_text)
-		*(.relefi_runtime_data)
+		*(.rel*.efi_runtime)
+		*(.rel*.efi_runtime.*)
 	}
 
 	.efi_runtime_rel_stop :

arch/arm/dts/Makefile

@@ -53,7 +53,9 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += \
 	rk3399-puma-ddr1866.dtb \
 	rv1108-evb.dtb
 dtb-$(CONFIG_ARCH_MESON) += \
+	meson-gxbb-nanopi-k2.dtb \
 	meson-gxbb-odroidc2.dtb \
+	meson-gxbb-nanopi-k2.dtb \
 	meson-gxl-s905x-p212.dtb \
 	meson-gxl-s905x-libretech-cc.dtb \
 	meson-gxl-s905x-khadas-vim.dtb
@@ -129,6 +131,8 @@ dtb-$(CONFIG_ARCH_UNIPHIER_SLD8) += \
 
 dtb-$(CONFIG_ARCH_ZYNQ) += \
 	zynq-cc108.dtb \
+	zynq-cse-nand.dtb \
+	zynq-cse-nor.dtb \
 	zynq-cse-qspi-single.dtb \
 	zynq-microzed.dtb \
 	zynq-minized.dtb \
@@ -150,6 +154,7 @@ dtb-$(CONFIG_ARCH_ZYNQMP) += \
 	zynqmp-mini-emmc0.dtb			\
 	zynqmp-mini-emmc1.dtb			\
 	zynqmp-mini-nand.dtb			\
+	zynqmp-mini-qspi.dtb			\
 	zynqmp-zcu100-revC.dtb			\
 	zynqmp-zcu102-revA.dtb			\
 	zynqmp-zcu102-revB.dtb			\
@@ -392,7 +397,8 @@ dtb-$(CONFIG_MACH_SUN50I) += \
 	sun50i-a64-olinuxino.dtb \
 	sun50i-a64-orangepi-win.dtb \
 	sun50i-a64-pine64-plus.dtb \
-	sun50i-a64-pine64.dtb
+	sun50i-a64-pine64.dtb \
+	sun50i-a64-sopine-baseboard.dtb
 dtb-$(CONFIG_MACH_SUN9I) += \
 	sun9i-a80-optimus.dtb \
 	sun9i-a80-cubieboard4.dtb \
@@ -535,7 +541,8 @@ dtb-$(CONFIG_ARCH_ASPEED) += ast2500-evb.dtb
 dtb-$(CONFIG_ARCH_STI) += stih410-b2260.dtb
 
 dtb-$(CONFIG_TARGET_STM32MP1) += \
-	stm32mp157c-ed1.dtb
+	stm32mp157c-ed1.dtb \
+	stm32mp157c-ev1.dtb
 
 targets += $(dtb-y)
 

arch/arm/dts/am335x-brppt1-mmc.dts

@@ -0,0 +1,345 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2018 B&R Industrial Automation GmbH
+ * http://www.br-automation.com
+ *
+ */
+/dts-v1/;
+
+#include "am33xx.dtsi"
+
+/ {
+	model = "BRPPT1 (MMC) Panel";
+	compatible = "ti,am33xx";
+
+	fset: factory-settings {
+		bl-version	= "ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456890";
+		version		= <0x0100>;
+		order-no	= "6PPT30 (MMC)";
+		hw-revision	= "ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456890";
+		serial-no	= "0";
+		device-id	= <0x0>;
+		parent-id	= <0x0>;
+		hw-variant	= <0x1>;
+	};
+
+	aliases {
+		ds1bkl0 = &pwmbacklight;
+		ds1bkl1 = &tps_bl;
+		ds1timing = &timing0;
+		ds1ctrl = &lcdc;
+		gpmc = &gpmc;
+		mmc = &mmc2;
+		fset = &fset;
+	};
+
+	chosen {
+		bootargs = "console=ttyO0,115200 earlyprintk";
+		stdout-path = &uart0;
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x10000000>; /* 256 MB */
+	};
+
+	panel {
+		status = "disabled";
+
+		compatible = "ti,tilcdc,panel";
+		enable-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
+
+		backlight = <&pwmbacklight>;
+		bkl-pwm = <&pwmbacklight>;
+		bkl-tps = <&tps_bl>;
+
+		panel-info {
+			ac-bias		= <255>;
+			ac-bias-intrpt	= <0>;
+			dma-burst-sz	= <16>;
+			bpp		= <32>;
+			fdd		= <0x80>;
+			sync-edge	= <0>;
+			sync-ctrl	= <1>;
+			raster-order	= <0>;
+			fifo-th		= <0>;
+		};
+
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: lcd {
+				clock-frequency	= <32000000>;
+				hactive		= <800>;
+				vactive		= <480>;
+				hfront-porch	= <2>;
+				hback-porch	= <192>;
+				hsync-len	= <1>;
+				vfront-porch	= <20>;
+				vback-porch	= <2>;
+				vsync-len	= <1>;
+				hsync-active	= <1>;
+				vsync-active	= <1>;
+				pupdelay	= <10>;
+				pondelay	= <10>;
+			};
+		};
+	};
+
+	vmmcsd_fixed: fixedregulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vmmcsd_fixed";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	pwm0: omap-pwm@timer5 {
+		compatible = "ti,omap-dmtimer-pwm";
+		ti,timers = <&timer5>;
+		#pwm-cells = <3>;
+	};
+
+	pwm1: omap-pwm@timer6 {
+		compatible = "ti,omap-dmtimer-pwm";
+		ti,timers = <&timer6>;
+		#pwm-cells = <3>;
+	};
+
+	beeper: pwm-beep {
+		compatible = "pwm-beeper";
+		pwms = <&pwm0 0 0 0>;
+	};
+
+	pwmbacklight: pwm-bkl {
+		compatible = "pwm-backlight";
+		pwms = <&pwm1 0 5000000 0>;
+
+		default-brightness-level = <255>;
+		brightness-levels = <0 16 32 64 128 170 202 234 255>;
+
+		power-supply = <&vmmcsd_fixed>;
+		enable-gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&uart0 {		/* console uart */
+	u-boot,dm-spl;
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&i2c0 {
+	u-boot,dm-spl;
+	status = "okay";
+	clock-frequency = <400000>;
+
+	tps: tps@24 {		/* PMIC controller */
+		u-boot,dm-spl;
+		reg = <0x24>;
+		compatible = "ti,tps65217";
+
+		tps_bl: backlight {
+			compatible = "ti,tps65217-bl";
+			isel = <1>;	/* 1 - ISET1, 2 ISET2 */
+			fdim = <1000>;	/* TPS65217_BL_FDIM_1kHZ */
+			default-brightness = <50>;
+		};
+	};
+};
+
+&i2c2 {
+	status = "okay";
+	clock-frequency = <100000>;
+};
+
+&edma {
+	status = "okay";
+};
+
+&cppi41dma  {
+	status = "okay";
+};
+
+&usb {
+	status = "okay";
+};
+
+&usb_ctrl_mod {
+	status = "okay";
+};
+
+&usb0_phy {
+	status = "okay";
+};
+
+&usb1_phy {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+	dr_mode = "host";
+};
+
+&usb1 {
+	status = "okay";
+	dr_mode = "host";
+};
+
+&davinci_mdio {
+	status = "okay";
+
+	phy0: ethernet-phy@0 {
+		reg = <1>;
+	};
+
+	phy1: ethernet-phy@1 {
+		reg = <2>;
+	};
+};
+
+&mac {
+	status = "okay";
+};
+
+&cpsw_emac0 {
+	phy-handle = <&phy0>;
+	dual_emac_res_vlan = <1>;
+	phy-mode = "mii";
+};
+
+&cpsw_emac1 {
+	phy-handle = <&phy1>;
+	dual_emac_res_vlan = <2>;
+	phy-mode = "mii";
+};
+
+&mmc1 {
+	u-boot,dm-spl;
+	vmmc-supply = <&vmmcsd_fixed>;
+	bus-width = <0x4>;
+	ti,non-removable;
+	ti,needs-special-hs-handling;
+	ti,vcc-aux-disable-is-sleep;
+	status = "okay";
+};
+
+&mmc2 {
+	u-boot,dm-spl;
+	vmmc-supply = <&vmmcsd_fixed>;
+	bus-width = <0x8>;
+	ti,non-removable;
+	ti,needs-special-hs-handling;
+	ti,vcc-aux-disable-is-sleep;
+	status = "okay";
+};
+
+&lcdc {
+	status = "disabled";
+};
+
+&elm {
+	status = "okay";
+};
+
+&sham {
+	status = "okay";
+};
+
+&aes {
+	status = "okay";
+};
+
+&gpio0 {
+	u-boot,dm-spl;
+	ti,no-reset-on-init;
+};
+
+&gpio1 {
+	u-boot,dm-spl;
+	ti,no-reset-on-init;
+};
+
+&gpio2 {
+	u-boot,dm-spl;
+	ti,no-reset-on-init;
+};
+
+&gpio3 {
+	u-boot,dm-spl;
+	ti,no-reset-on-init;
+};
+
+&wdt2 {
+	ti,no-reset-on-init;
+	ti,no-idle-on-init;
+};
+
+&tscadc {
+	status = "okay";
+	tsc {
+		ti,wires = <4>;
+		ti,x-plate-resistance = <200>;
+		ti,zx-cutoff-ratio = <40>;
+		ti,min_deviation = <60>;
+		ti,max_deviation = <600>;
+		ti,coordinate-readouts = <5>;
+		ti,wire-config = <0x00 0x11 0x22 0x33>;
+
+		bnr-buttons {
+			Home-Button {};
+		};
+	};
+
+	adc {
+		ti,adc-channels = <5 6 7>;
+	};
+};
+
+&timer6 {		/* used for cpsw end device */
+	status = "okay";
+	ti,no-reset-on-init;
+	ti,no-idle-on-init;
+};
+
+&timer7 {		/* used for cpsw end device */
+	status = "okay";
+	ti,no-reset-on-init;
+	ti,no-idle-on-init;
+};
+
+&wdt2 {
+	status = "okay";
+	ti,no-reset-on-init;
+	ti,no-idle-on-init;
+};
+
+&epwmss0 {
+	status = "okay";
+};
+
+&tscadc {
+	status = "okay";
+};
+
+&dcan0 {
+	status = "okay";
+};
+
+&dcan1 {
+	status = "okay";
+};
+
+&sham {
+	status = "disabled";
+};
+
+&aes {
+	status = "disabled";
+};
+
+&rng {
+	status = "disabled";
+};

arch/arm/dts/am335x-brppt1-nand.dts

@@ -0,0 +1,363 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2018 B&R Industrial Automation GmbH
+ * http://www.br-automation.com
+ *
+ */
+/dts-v1/;
+
+#include "am33xx.dtsi"
+
+/ {
+	model = "BRPPT1 (NAND) Panel";
+	compatible = "ti,am33xx";
+
+	fset: factory-settings {
+		bl-version	= "ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456890";
+		version		= <0x0100>;
+		order-no	= "6PPT30 (NAND)";
+		hw-revision	= "ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456890";
+		serial-no	= "0";
+		device-id	= <0x0>;
+		parent-id	= <0x0>;
+		hw-variant	= <0x1>;
+	};
+
+	aliases {
+		ds1bkl0 = &pwmbacklight;
+		ds1bkl1 = &tps_bl;
+		ds1timing = &timing0;
+		ds1ctrl = &lcdc;
+		gpmc = &gpmc;
+		mmc = &mmc2;
+		fset = &fset;
+	};
+
+	chosen {
+		bootargs = "console=ttyO0,115200 earlyprintk";
+		stdout-path = &uart0;
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x10000000>; /* 256 MB */
+	};
+
+	panel {
+		status = "disabled";
+
+		compatible = "ti,tilcdc,panel";
+		enable-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
+
+		backlight = <&pwmbacklight>;
+		bkl-pwm = <&pwmbacklight>;
+		bkl-tps = <&tps_bl>;
+
+		panel-info {
+			ac-bias		= <255>;
+			ac-bias-intrpt	= <0>;
+			dma-burst-sz	= <16>;
+			bpp		= <32>;
+			fdd		= <0x80>;
+			sync-edge	= <0>;
+			sync-ctrl	= <1>;
+			raster-order	= <0>;
+			fifo-th		= <0>;
+		};
+
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: lcd {
+				clock-frequency	= <32000000>;
+				hactive		= <800>;
+				vactive		= <480>;
+				hfront-porch	= <2>;
+				hback-porch	= <192>;
+				hsync-len	= <1>;
+				vfront-porch	= <20>;
+				vback-porch	= <2>;
+				vsync-len	= <1>;
+				hsync-active	= <1>;
+				vsync-active	= <1>;
+				pupdelay	= <10>;
+				pondelay	= <10>;
+			};
+		};
+	};
+
+	vmmcsd_fixed: fixedregulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vmmcsd_fixed";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	pwm0: omap-pwm@timer5 {
+		compatible = "ti,omap-dmtimer-pwm";
+		ti,timers = <&timer5>;
+		#pwm-cells = <3>;
+	};
+
+	pwm1: omap-pwm@timer6 {
+		compatible = "ti,omap-dmtimer-pwm";
+		ti,timers = <&timer6>;
+		#pwm-cells = <3>;
+	};
+
+	beeper: pwm-beep {
+		compatible = "pwm-beeper";
+		pwms = <&pwm0 0 0 0>;
+	};
+
+	pwmbacklight: pwm-bkl {
+		compatible = "pwm-backlight";
+		pwms = <&pwm1 0 5000000 0>;
+
+		default-brightness-level = <255>;
+		brightness-levels = <0 16 32 64 128 170 202 234 255>;
+
+		power-supply = <&vmmcsd_fixed>;
+		enable-gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&uart0 {		/* console uart */
+	u-boot,dm-spl;
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&i2c0 {
+	u-boot,dm-spl;
+	status = "okay";
+	clock-frequency = <400000>;
+
+	tps: tps@24 {		/* PMIC controller */
+		u-boot,dm-spl;
+		reg = <0x24>;
+		compatible = "ti,tps65217";
+
+		tps_bl: backlight {
+			compatible = "ti,tps65217-bl";
+			isel = <1>;	/* 1 - ISET1, 2 ISET2 */
+			fdim = <1000>;	/* TPS65217_BL_FDIM_1kHZ */
+			default-brightness = <50>;
+		};
+	};
+};
+
+&i2c2 {
+	status = "okay";
+	clock-frequency = <100000>;
+};
+
+&edma {
+	status = "okay";
+};
+
+&cppi41dma  {
+	status = "okay";
+};
+
+&usb {
+	status = "okay";
+};
+
+&usb_ctrl_mod {
+	status = "okay";
+};
+
+&usb0_phy {
+	status = "okay";
+};
+
+&usb1_phy {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+	dr_mode = "host";
+};
+
+&usb1 {
+	status = "okay";
+	dr_mode = "host";
+};
+
+&davinci_mdio {
+	status = "okay";
+
+	phy0: ethernet-phy@0 {
+		reg = <1>;
+	};
+
+	phy1: ethernet-phy@1 {
+		reg = <2>;
+	};
+};
+
+&mac {
+	dual_emac;
+	status = "okay";
+};
+
+&cpsw_emac0 {
+	phy-handle = <&phy0>;
+	dual_emac_res_vlan = <1>;
+	phy-mode = "mii";
+};
+
+&cpsw_emac1 {
+	phy-handle = <&phy1>;
+	dual_emac_res_vlan = <2>;
+	phy-mode = "mii";
+};
+
+&mmc2 {
+	vmmc-supply = <&vmmcsd_fixed>;
+	bus-width = <0x4>;
+	ti,non-removable;
+	ti,needs-special-hs-handling;
+	ti,vcc-aux-disable-is-sleep;
+	status = "disabled";
+};
+
+&lcdc {
+	status = "disabled";
+};
+
+&elm {
+	status = "okay";
+};
+
+&sham {
+	status = "okay";
+};
+
+&aes {
+	status = "okay";
+};
+
+&gpio0 {
+	u-boot,dm-spl;
+	ti,no-reset-on-init;
+};
+
+&gpio1 {
+	u-boot,dm-spl;
+	ti,no-reset-on-init;
+};
+
+&gpio2 {
+	u-boot,dm-spl;
+	ti,no-reset-on-init;
+};
+
+&gpio3 {
+	u-boot,dm-spl;
+	ti,no-reset-on-init;
+};
+
+&wdt2 {
+	ti,no-reset-on-init;
+	ti,no-idle-on-init;
+};
+
+&tscadc {
+	status = "okay";
+	tsc {
+		ti,wires = <4>;
+		ti,x-plate-resistance = <200>;
+		ti,zx-cutoff-ratio = <40>;
+		ti,min_deviation = <60>;
+		ti,max_deviation = <600>;
+		ti,coordinate-readouts = <5>;
+		ti,wire-config = <0x00 0x11 0x22 0x33>;
+
+		bnr-buttons {
+			Home-Button {};
+		};
+	};
+
+	adc {
+		ti,adc-channels = <5 6 7>;
+	};
+};
+
+&gpmc {
+	u-boot,dm-spl;
+	status = "okay";
+	pinctrl-names = "default";
+	ranges = <0 0 0x08000000 0x10000000>;	/* CS0: NAND */
+	nand@0,0 {
+		compatible = "ti,omap2-nand";
+		reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
+		interrupt-parent = <&gpmc>;
+		rb-gpios = <&gpmc 1 GPIO_ACTIVE_HIGH>; /* gpmc_wait1 */
+		ti,nand-ecc-opt = "bch8";
+		ti,elm-id = <&elm>;
+		nand-bus-width = <8>;
+		gpmc,device-width = <1>;
+		gpmc,sync-clk-ps = <0>;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <44>;
+		gpmc,cs-wr-off-ns = <44>;
+		gpmc,adv-on-ns = <6>;
+		gpmc,adv-rd-off-ns = <34>;
+		gpmc,adv-wr-off-ns = <44>;
+		gpmc,we-on-ns = <0>;
+		gpmc,we-off-ns = <40>;
+		gpmc,oe-on-ns = <0>;
+		gpmc,oe-off-ns = <54>;
+		gpmc,access-ns = <64>;
+		gpmc,rd-cycle-ns = <82>;
+		gpmc,wr-cycle-ns = <82>;
+		gpmc,wait-on-read = "true";
+		gpmc,wait-on-write = "true";
+		gpmc,bus-turnaround-ns = <0>;
+		gpmc,cycle2cycle-delay-ns = <0>;
+		gpmc,clk-activation-ns = <0>;
+		gpmc,wait-monitoring-ns = <0>;
+		gpmc,wr-access-ns = <40>;
+		gpmc,wr-data-mux-bus-ns = <0>;
+		gpmc,wait-pin = <1>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		partition@0 {
+			label = "NAND.MLO";
+			reg = <0x00000000 0x000020000>;
+		};
+		partition@1 {
+			label = "NAND.cfgscr";
+			reg = <0x00020000 0x00020000>;
+		};
+		partition@2 {
+			label = "NAND.dtb";
+			reg = <0x00040000 0x00020000>;
+		};
+		partition@3 {
+			label = "NAND.u-boot-env";
+			reg = <0x00060000 0x00020000>;
+		};
+		partition@4 {
+			label = "NAND.u-boot";
+			reg = <0x00080000 0x00080000>;
+		};
+		partition@5 {
+			label = "NAND.kernel";
+			reg = <0x00100000 0x00400000>;
+		};
+		partition@6 {
+			label = "NAND.rootfs";
+			reg = <0x00500000 0x08000000>;
+		};
+		partition@7 {
+			label = "NAND.user";
+			reg = <0x08500000 0x17b00000>;
+		};
+	};
+};

arch/arm/dts/am335x-brppt1-spi.dts

@@ -0,0 +1,366 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2018 B&R Industrial Automation GmbH
+ * http://www.br-automation.com
+ *
+ */
+/dts-v1/;
+
+#include "am33xx.dtsi"
+
+/ {
+	model = "BRPPT1 (MMC) Panel";
+	compatible = "ti,am33xx";
+
+	fset: factory-settings {
+		bl-version	= "ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456890";
+		version		= <0x0100>;
+		order-no	= "6PPT30 (SPI)";
+		hw-revision	= "ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456890";
+		serial-no	= "0";
+		device-id	= <0x0>;
+		parent-id	= <0x0>;
+		hw-variant	= <0x1>;
+	};
+
+	aliases {
+		ds1bkl0 = &pwmbacklight;
+		ds1bkl1 = &tps_bl;
+		ds1timing = &timing0;
+		ds1ctrl = &lcdc;
+		gpmc = &gpmc;
+		mmc = &mmc2;
+		spi0 = &spi0;
+		fset = &fset;
+	};
+
+	chosen {
+		bootargs = "console=ttyO0,115200 earlyprintk";
+		stdout-path = &uart0;
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x10000000>; /* 256 MB */
+	};
+
+	panel {
+		status = "disabled";
+
+		compatible = "ti,tilcdc,panel";
+		enable-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
+
+		backlight = <&pwmbacklight>;
+		bkl-pwm = <&pwmbacklight>;
+		bkl-tps = <&tps_bl>;
+
+		panel-info {
+			ac-bias		= <255>;
+			ac-bias-intrpt	= <0>;
+			dma-burst-sz	= <16>;
+			bpp		= <32>;
+			fdd		= <0x80>;
+			sync-edge	= <0>;
+			sync-ctrl	= <1>;
+			raster-order	= <0>;
+			fifo-th		= <0>;
+		};
+
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: lcd {
+				clock-frequency	= <32000000>;
+				hactive		= <800>;
+				vactive		= <480>;
+				hfront-porch	= <2>;
+				hback-porch	= <192>;
+				hsync-len	= <1>;
+				vfront-porch	= <20>;
+				vback-porch	= <2>;
+				vsync-len	= <1>;
+				hsync-active	= <1>;
+				vsync-active	= <1>;
+				pupdelay	= <10>;
+				pondelay	= <10>;
+			};
+		};
+	};
+
+	vmmcsd_fixed: fixedregulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vmmcsd_fixed";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	pwm0: omap-pwm@timer5 {
+		compatible = "ti,omap-dmtimer-pwm";
+		ti,timers = <&timer5>;
+		#pwm-cells = <3>;
+	};
+
+	pwm1: omap-pwm@timer6 {
+		compatible = "ti,omap-dmtimer-pwm";
+		ti,timers = <&timer6>;
+		#pwm-cells = <3>;
+	};
+
+	beeper: pwm-beep {
+		compatible = "pwm-beeper";
+		pwms = <&pwm0 0 0 0>;
+	};
+
+	pwmbacklight: pwm-bkl {
+		compatible = "pwm-backlight";
+		pwms = <&pwm1 0 5000000 0>;
+
+		default-brightness-level = <255>;
+		brightness-levels = <0 16 32 64 128 170 202 234 255>;
+
+		power-supply = <&vmmcsd_fixed>;
+		enable-gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&uart0 {		/* console uart */
+	u-boot,dm-spl;
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&i2c0 {
+	u-boot,dm-spl;
+	status = "okay";
+	clock-frequency = <400000>;
+
+	tps: tps@24 {		/* PMIC controller */
+		u-boot,dm-spl;
+		reg = <0x24>;
+		compatible = "ti,tps65217";
+
+		tps_bl: backlight {
+			compatible = "ti,tps65217-bl";
+			isel = <1>;	/* 1 - ISET1, 2 ISET2 */
+			fdim = <1000>;	/* TPS65217_BL_FDIM_1kHZ */
+			default-brightness = <50>;
+		};
+	};
+};
+
+&i2c2 {
+	status = "okay";
+	clock-frequency = <100000>;
+};
+
+&spi0 {
+	u-boot,dm-spl;
+	status = "okay";
+
+	cs-gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>,
+		   <&gpio0 6 GPIO_ACTIVE_HIGH>,
+		   <0>,
+		   <0>;
+
+	spi-max-frequency = <24000000>;
+
+	spi_flash: spiflash@0 {
+		u-boot,dm-spl;
+		u-boot,dm-pre-reloc;
+		compatible = "spidev", "spi-flash";
+		spi-max-frequency = <24000000>;
+		reg = <0>;
+	};
+};
+
+&edma {
+	status = "okay";
+};
+
+&cppi41dma  {
+	status = "okay";
+};
+
+&usb {
+	status = "okay";
+};
+
+&usb_ctrl_mod {
+	status = "okay";
+};
+
+&usb0_phy {
+	status = "okay";
+};
+
+&usb1_phy {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+	dr_mode = "host";
+};
+
+&usb1 {
+	status = "okay";
+	dr_mode = "host";
+};
+
+&davinci_mdio {
+	status = "okay";
+
+	phy0: ethernet-phy@0 {
+		reg = <1>;
+	};
+
+	phy1: ethernet-phy@1 {
+		reg = <2>;
+	};
+};
+
+&mac {
+	status = "okay";
+};
+
+&cpsw_emac0 {
+	phy-handle = <&phy0>;
+	dual_emac_res_vlan = <1>;
+	phy-mode = "mii";
+};
+
+&cpsw_emac1 {
+	phy-handle = <&phy1>;
+	dual_emac_res_vlan = <2>;
+	phy-mode = "mii";
+};
+
+&mmc1 {
+	u-boot,dm-spl;
+	vmmc-supply = <&vmmcsd_fixed>;
+	bus-width = <0x4>;
+	ti,non-removable;
+	ti,needs-special-hs-handling;
+	ti,vcc-aux-disable-is-sleep;
+	status = "okay";
+};
+
+&mmc2 {
+	u-boot,dm-spl;
+	vmmc-supply = <&vmmcsd_fixed>;
+	bus-width = <0x8>;
+	ti,non-removable;
+	ti,needs-special-hs-handling;
+	ti,vcc-aux-disable-is-sleep;
+	status = "okay";
+};
+
+&lcdc {
+	status = "disabled";
+};
+
+&elm {
+	status = "okay";
+};
+
+&sham {
+	status = "okay";
+};
+
+&aes {
+	status = "okay";
+};
+
+&gpio0 {
+	u-boot,dm-spl;
+	ti,no-reset-on-init;
+};
+
+&gpio1 {
+	u-boot,dm-spl;
+	ti,no-reset-on-init;
+};
+
+&gpio2 {
+	u-boot,dm-spl;
+	ti,no-reset-on-init;
+};
+
+&gpio3 {
+	u-boot,dm-spl;
+	ti,no-reset-on-init;
+};
+
+&wdt2 {
+	ti,no-reset-on-init;
+	ti,no-idle-on-init;
+};
+
+&tscadc {
+	status = "okay";
+	tsc {
+		ti,wires = <4>;
+		ti,x-plate-resistance = <200>;
+		ti,zx-cutoff-ratio = <40>;
+		ti,min_deviation = <60>;
+		ti,max_deviation = <600>;
+		ti,coordinate-readouts = <5>;
+		ti,wire-config = <0x00 0x11 0x22 0x33>;
+
+		bnr-buttons {
+			Home-Button {};
+		};
+	};
+
+	adc {
+		ti,adc-channels = <5 6 7>;
+	};
+};
+
+&timer6 {		/* used for cpsw end device */
+	status = "okay";
+	ti,no-reset-on-init;
+	ti,no-idle-on-init;
+};
+
+&timer7 {		/* used for cpsw end device */
+	status = "okay";
+	ti,no-reset-on-init;
+	ti,no-idle-on-init;
+};
+
+&wdt2 {
+	status = "okay";
+	ti,no-reset-on-init;
+	ti,no-idle-on-init;
+};
+
+&epwmss0 {
+	status = "okay";
+};
+
+&tscadc {
+	status = "okay";
+};
+
+&dcan0 {
+	status = "okay";
+};
+
+&dcan1 {
+	status = "okay";
+};
+
+&sham {
+	status = "disabled";
+};
+
+&aes {
+	status = "disabled";
+};
+
+&rng {
+	status = "disabled";
+};

arch/arm/dts/am33xx.dtsi

@@ -91,6 +91,7 @@
 	 * the whole bus hierarchy.
 	 */
 	ocp {
+		u-boot,dm-spl;
 		compatible = "simple-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;

arch/arm/dts/am3517-evm-u-boot.dtsi

@@ -9,3 +9,19 @@
 		stdout-path = &uart3;
 	};
 };
+
+&mmc1 {
+	cd-inverted;
+};
+
+&uart1 {
+	reg-shift = <2>;
+};
+
+&uart2 {
+	reg-shift = <2>;
+};
+
+&uart3 {
+	reg-shift = <2>;
+};

arch/arm/dts/am3517-evm.dts

@@ -8,11 +8,17 @@
 /dts-v1/;
 
 #include "am3517.dtsi"
+#include "am3517-som.dtsi"
+#include <dt-bindings/input/input.h>
 
 / {
 	model = "TI AM3517 EVM (AM3517/05 TMDSEVM3517)";
 	compatible = "ti,am3517-evm", "ti,am3517", "ti,omap3";
 
+	aliases {
+		display0 = &lcd0;
+	};
+
 	memory@80000000 {
 		device_type = "memory";
 		reg = <0x80000000 0x10000000>; /* 256 MB */
@@ -24,6 +30,144 @@
                 regulator-min-microvolt = <3300000>;
                 regulator-max-microvolt = <3300000>;
         };
+
+	gpio-keys {
+		compatible = "gpio-keys-polled";
+		poll-interval = <100>;
+
+		user_pb {
+			label = "User Push Button";
+			linux,code = <BTN_0>;
+			gpios = <&tca6416 5 GPIO_ACTIVE_LOW>;
+		};
+
+		user_sw_1 {
+			label = "User Switch 1";
+			linux,code = <BTN_1>;
+			gpios = <&tca6416 8 GPIO_ACTIVE_LOW>;
+		};
+
+		user_sw_2 {
+			label = "User Switch 2";
+			linux,code = <BTN_2>;
+			gpios = <&tca6416 9 GPIO_ACTIVE_LOW>;
+		};
+
+		user_sw_3 {
+			label = "User Switch 3";
+			linux,code = <BTN_3>;
+			gpios = <&tca6416 10 GPIO_ACTIVE_LOW>;
+		};
+
+		user_sw_4 {
+			label = "User Switch 4";
+			linux,code = <BTN_4>;
+			gpios = <&tca6416 11 GPIO_ACTIVE_LOW>;
+		};
+
+		user_sw_5 {
+			label = "User Switch 5";
+			linux,code = <BTN_5>;
+			gpios = <&tca6416 12 GPIO_ACTIVE_LOW>;
+		};
+
+		user_sw_6 {
+			label = "User Switch 6";
+			linux,code = <BTN_6>;
+			gpios = <&tca6416 13 GPIO_ACTIVE_LOW>;
+		};
+
+		user_sw_7 {
+			label = "User Switch 7";
+			linux,code = <BTN_7>;
+			gpios = <&tca6416 14 GPIO_ACTIVE_LOW>;
+		};
+
+		user_sw_8 {
+			label = "User Switch 8";
+			linux,code = <BTN_8>;
+			gpios = <&tca6416 15 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&leds_pins>;
+
+		user_led_1 {
+			label = "am3517evm:green:user_led_1";
+			gpios = <&tca6416 7 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+		};
+
+		user_led_2 {
+			label = "am3517evm:green:user_led_2";
+			gpios = <&tca6416 6 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+		};
+
+		user_led_3 {
+			label = "am3517evm:green:user_led_3";
+			gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc0"; /* SD/MMC card activity */
+		};
+
+		user_led_4 {
+			label = "am3517evm:green:user_led_4";
+			gpios = <&gpio1 31 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	lcd0: display@0 {
+		compatible = "panel-dpi";
+		label = "15";
+		status = "okay";
+		pinctrl-names = "default";
+		enable-gpios = <&gpio6 16 GPIO_ACTIVE_HIGH>;	/* gpio176, lcd INI */
+
+		port {
+			lcd_in: endpoint {
+				remote-endpoint = <&dpi_out>;
+			};
+		};
+
+		panel-timing {
+			clock-frequency = <9000000>;
+			hactive = <480>;
+			vactive = <272>;
+			hfront-porch = <3>;
+			hback-porch = <2>;
+			hsync-len = <42>;
+			vback-porch = <3>;
+			vfront-porch = <4>;
+			vsync-len = <11>;
+			hsync-active = <0>;
+			vsync-active = <0>;
+			de-active = <1>;
+			pixelclk-active = <1>;
+		};
+	};
+
+	bl: backlight {
+		compatible = "pwm-backlight";
+		pinctrl-names = "default";
+		pinctrl-0 = <&backlight_pins>;
+		pwms = <&pwm11 0 5000000 0>;
+		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+		default-brightness-level = <7>;
+		enable-gpios = <&gpio6 22 GPIO_ACTIVE_HIGH>; /* gpio_182 */
+	};
+
+	pwm11: dmtimer-pwm@11 {
+		compatible = "ti,omap-dmtimer-pwm";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pwm_pins>;
+		ti,timers = <&timer11>;
+		#pwm-cells = <3>;
+	};
 };
 
 &davinci_emac {
@@ -34,12 +178,32 @@
 	     status = "okay";
 };
 
-&i2c1 {
-	clock-frequency = <400000>;
+&dss {
+	status = "ok";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&dss_dpi_pins>;
+
+	vdds_dsi-supply = <&vdd_io_reg>;
+	vdda_video-supply = <&vdd_io_reg>;
+
+	port {
+		dpi_out: endpoint {
+			remote-endpoint = <&lcd_in>;
+			data-lines = <16>;
+		};
+	};
 };
 
 &i2c2 {
 	clock-frequency = <400000>;
+	/* User DIP swithes [1:8] / User LEDS [1:2] */
+	tca6416: gpio@21 {
+		compatible = "ti,tca6416";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
 };
 
 &i2c3 {
@@ -47,8 +211,13 @@
 };
 
 &mmc1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
 	vmmc-supply = <&vmmc_fixed>;
 	bus-width = <4>;
+	wp-gpios = <&gpio4 30 GPIO_ACTIVE_HIGH>; /* gpio_126 */
+	cd-gpios = <&gpio4 31 GPIO_ACTIVE_HIGH>; /* gpio_127 */
 };
 
 &mmc2 {
@@ -59,3 +228,63 @@
       status = "disabled";
 };
 
+&omap3_pmx_core {
+
+	leds_pins: pinmux_leds_pins {
+		pinctrl-single,pins = <
+			OMAP3_WKUP_IOPAD(0x2a24, PIN_OUTPUT_PULLUP | MUX_MODE4)	/* jtag_emu0.gpio_11 */
+			OMAP3_WKUP_IOPAD(0x2a26, PIN_OUTPUT_PULLUP | MUX_MODE4)	/* jtag_emu1.gpio_31 */
+		>;
+	};
+
+	mmc1_pins: pinmux_mmc1_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_clk.sdmmc1_clk */
+			OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_cmd.sdmmc1_cmd */
+			OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_dat0.sdmmc1_dat0 */
+			OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_dat1.sdmmc1_dat1 */
+			OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_dat2.sdmmc1_dat2 */
+			OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_dat3.sdmmc1_dat3 */
+			OMAP3_CORE1_IOPAD(0x2150, PIN_INPUT_PULLUP | MUX_MODE4) /* sdmmc1_dat4.gpio_126 */
+			OMAP3_CORE1_IOPAD(0x2152, PIN_INPUT_PULLUP | MUX_MODE4) /* sdmmc1_dat5.gpio_127 */
+		>;
+	};
+
+	pwm_pins: pinmux_pwm_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21dc, PIN_OUTPUT | MUX_MODE1)       /* mcspi2_cs0.gpt11_pwm */
+		>;
+	};
+
+	backlight_pins: pinmux_backlight_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21de, PIN_OUTPUT | MUX_MODE4)       /* mcspi2_cs1.gpio_182 */
+		>;
+	};
+
+	dss_dpi_pins: pinmux_dss_dpi_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21d2, PIN_OUTPUT | MUX_MODE4)       /* mcspi1_cs2.gpio_176 */
+			OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0)       /* dss_pclk.dss_pclk */
+			OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0)       /* dss_hsync.dss_hsync */
+			OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT | MUX_MODE0)       /* dss_vsync.dss_vsync */
+			OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT | MUX_MODE0)       /* dss_acbias.dss_acbias */
+			OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT | MUX_MODE0)       /* dss_data0.dss_data0 */
+			OMAP3_CORE1_IOPAD(0x20de, PIN_OUTPUT | MUX_MODE0)       /* dss_data1.dss_data1 */
+			OMAP3_CORE1_IOPAD(0x20e0, PIN_OUTPUT | MUX_MODE0)       /* dss_data2.dss_data2 */
+			OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE0)       /* dss_data3.dss_data3 */
+			OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT | MUX_MODE0)       /* dss_data4.dss_data4 */
+			OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT | MUX_MODE0)       /* dss_data5.dss_data5 */
+			OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT | MUX_MODE0)       /* dss_data6.dss_data6 */
+			OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT | MUX_MODE0)       /* dss_data7.dss_data7 */
+			OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT | MUX_MODE0)       /* dss_data8.dss_data8 */
+			OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT | MUX_MODE0)       /* dss_data9.dss_data9 */
+			OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE0)       /* dss_data10.dss_data10 */
+			OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE0)       /* dss_data11.dss_data11 */
+			OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT | MUX_MODE0)       /* dss_data12.dss_data12 */
+			OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT | MUX_MODE0)       /* dss_data13.dss_data13 */
+			OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT | MUX_MODE0)       /* dss_data14.dss_data14 */
+			OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT | MUX_MODE0)       /* dss_data15.dss_data15 */
+		>;
+	};
+};

arch/arm/dts/am3517-som.dtsi

@@ -0,0 +1,142 @@
+/*
+ * Copyright (C) 2016 Derald D. Woods <woods.technical@gmail.com>
+ *
+ * Based on am3517-evm.dts
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/ {
+	cpus {
+		cpu@0 {
+			cpu0-supply = <&vdd_core_reg>;
+		};
+	};
+};
+
+&gpmc {
+	ranges = <0 0 0x30000000 0x1000000>;	/* CS0: 16MB for NAND */
+
+	nand@0,0 {
+		compatible = "ti,omap2-nand";
+		linux,mtd-name = "micron,mt29f4g16abchch";
+		reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
+		nand-bus-width = <16>;
+		ti,nand-ecc-opt = "bch8";
+		gpmc,sync-clk-ps = <0>;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <44>;
+		gpmc,cs-wr-off-ns = <44>;
+		gpmc,adv-on-ns = <6>;
+		gpmc,adv-rd-off-ns = <34>;
+		gpmc,adv-wr-off-ns = <44>;
+		gpmc,we-off-ns = <40>;
+		gpmc,oe-off-ns = <54>;
+		gpmc,access-ns = <64>;
+		gpmc,rd-cycle-ns = <82>;
+		gpmc,wr-cycle-ns = <82>;
+		gpmc,wr-access-ns = <40>;
+		gpmc,wr-data-mux-bus-ns = <0>;
+		gpmc,device-width = <2>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
+
+&i2c1 {
+	clock-frequency = <400000>;
+
+	s35390a: s35390a@30 {
+		compatible = "sii,s35390a";
+		reg = <0x30>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&rtc_pins>;
+		interrupts-extended = <&gpio2 23 IRQ_TYPE_EDGE_FALLING>; /* gpio_55 */
+	};
+
+	tps: tps65023@48 {
+		compatible = "ti,tps65023";
+		reg = <0x48>;
+
+		regulators {
+			vdd_core_reg: VDCDC1 {
+				regulator-name = "vdd_core";
+				compatible = "regulator-fixed";
+				regulator-always-on;
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+			};
+
+			vdd_io_reg: VDCDC2 {
+				regulator-name = "vdd_io";
+				compatible = "regulator-fixed";
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			vdd_1v8_reg: VDCDC3 {
+				regulator-name = "vdd_1v8";
+				compatible = "regulator-fixed";
+				regulator-always-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			vdd_usb18_reg: LDO1 {
+				regulator-name = "vdd_usb18";
+				compatible = "regulator-fixed";
+				regulator-always-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			vdd_usb33_reg: LDO2 {
+				regulator-name = "vdd_usb33";
+				compatible = "regulator-fixed";
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+		};
+	};
+
+	touchscreen: tsc2004@4b {
+		compatible = "ti,tsc2004";
+		reg = <0x4b>;
+
+		vio-supply = <&vdd_io_reg>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&tsc2004_pins>;
+		interrupts-extended = <&gpio3 1 IRQ_TYPE_EDGE_RISING>; /* gpio_65 */
+
+		touchscreen-fuzz-x = <4>;
+		touchscreen-fuzz-y = <7>;
+		touchscreen-fuzz-pressure = <2>;
+		touchscreen-size-x = <480>;
+		touchscreen-size-y = <272>;
+		touchscreen-max-pressure = <2048>;
+
+		ti,x-plate-ohms = <280>;
+		ti,esd-recovery-timeout-ms = <8000>;
+	};
+};
+
+&omap3_pmx_core {
+
+	rtc_pins: pinmux_rtc_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x20b6, PIN_INPUT_PULLUP | MUX_MODE4) /* gpmc_ncs4.gpio_55 */
+		>;
+	};
+
+	tsc2004_pins: pinmux_tsc2004_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x20d2, PIN_INPUT | MUX_MODE4) /* gpmc_wait3.gpio_65 */
+		>;
+	};
+};

arch/arm/dts/am3517.dtsi

@@ -39,6 +39,8 @@
 			ti,davinci-ctrl-ram-size = <0x2000>;
 			ti,davinci-rmii-en = /bits/ 8 <1>;
 			local-mac-address = [ 00 00 00 00 00 00 ];
+			clocks = <&emac_ick>;
+			clock-names = "ick";
 		};
 
 		davinci_mdio: ethernet@5c030000 {
@@ -49,6 +51,8 @@
 			bus_freq = <1000000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			clocks = <&emac_fck>;
+			clock-names = "fck";
 		};
 
 		uart4: serial@4809e000 {

arch/arm/dts/axp803.dtsi

@@ -0,0 +1,155 @@
+/*
+ * Copyright 2017 Icenowy Zheng <icenowy@aosc.xyz>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/*
+ * AXP803 Integrated Power Management Chip
+ * http://files.pine64.org/doc/datasheet/pine64/AXP803_Datasheet_V1.0.pdf
+ */
+
+&axp803 {
+	interrupt-controller;
+	#interrupt-cells = <1>;
+
+	regulators {
+		/* Default work frequency for buck regulators */
+		x-powers,dcdc-freq = <3000>;
+
+		reg_aldo1: aldo1 {
+			regulator-name = "aldo1";
+		};
+
+		reg_aldo2: aldo2 {
+			regulator-name = "aldo2";
+		};
+
+		reg_aldo3: aldo3 {
+			regulator-name = "aldo3";
+		};
+
+		reg_dc1sw: dc1sw {
+			regulator-name = "dc1sw";
+		};
+
+		reg_dcdc1: dcdc1 {
+			regulator-name = "dcdc1";
+		};
+
+		reg_dcdc2: dcdc2 {
+			regulator-name = "dcdc2";
+		};
+
+		reg_dcdc3: dcdc3 {
+			regulator-name = "dcdc3";
+		};
+
+		reg_dcdc4: dcdc4 {
+			regulator-name = "dcdc4";
+		};
+
+		reg_dcdc5: dcdc5 {
+			regulator-name = "dcdc5";
+		};
+
+		reg_dcdc6: dcdc6 {
+			regulator-name = "dcdc6";
+		};
+
+		reg_dldo1: dldo1 {
+			regulator-name = "dldo1";
+		};
+
+		reg_dldo2: dldo2 {
+			regulator-name = "dldo2";
+		};
+
+		reg_dldo3: dldo3 {
+			regulator-name = "dldo3";
+		};
+
+		reg_dldo4: dldo4 {
+			regulator-name = "dldo4";
+		};
+
+		reg_eldo1: eldo1 {
+			regulator-name = "eldo1";
+		};
+
+		reg_eldo2: eldo2 {
+			regulator-name = "eldo2";
+		};
+
+		reg_eldo3: eldo3 {
+			regulator-name = "eldo3";
+		};
+
+		reg_fldo1: fldo1 {
+			regulator-name = "fldo1";
+		};
+
+		reg_fldo2: fldo2 {
+			regulator-name = "fldo2";
+		};
+
+		reg_ldo_io0: ldo-io0 {
+			regulator-name = "ldo-io0";
+			status = "disabled";
+		};
+
+		reg_ldo_io1: ldo-io1 {
+			regulator-name = "ldo-io1";
+			status = "disabled";
+		};
+
+		reg_rtc_ldo: rtc-ldo {
+			/* RTC_LDO is a fixed, always-on regulator */
+			regulator-always-on;
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-name = "rtc-ldo";
+		};
+
+		reg_drivevbus: drivevbus {
+			regulator-name = "drivevbus";
+			status = "disabled";
+		};
+	};
+};

arch/arm/dts/bubblegum_96.dts

@@ -0,0 +1,31 @@
+// SPDX-License-Identifier: GPL-2.0+
+//
+// Device Tree Source for Bubblegum-96
+//
+// Copyright (C) 2015 Actions Semi Co., Ltd.
+// Copyright (C) 2018 Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
+
+/dts-v1/;
+#include "s900.dtsi"
+
+/ {
+	model = "Bubblegum-96";
+	compatible = "ucrobotics,bubblegum-96", "actions,s900";
+
+	aliases {
+		serial5 = &uart5;
+	};
+
+	chosen {
+		stdout-path = "serial5:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>;
+	};
+};
+
+&uart5 {
+	status = "okay";
+};

arch/arm/dts/dragonboard410c-uboot.dtsi

@@ -6,6 +6,11 @@
  */
 
 / {
+
+	smem {
+		u-boot,dm-pre-reloc;
+	};
+
 	soc {
 		u-boot,dm-pre-reloc;
 

arch/arm/dts/dragonboard410c.dts

@@ -27,18 +27,34 @@
 		#address-cells = <2>;
 		#size-cells = <2>;
 		ranges;
+
+		smem_mem: smem_region@86300000 {
+			reg = <0x0 0x86300000 0x0 0x100000>;
+			no-map;
+		};
 	};
 
 	chosen {
 		stdout-path = "/soc/serial@78b0000";
 	};
 
+	smem {
+		compatible = "qcom,smem";
+		memory-region = <&smem_mem>;
+		qcom,rpm-msg-ram = <&rpm_msg_ram>;
+	};
+
 	soc {
 		#address-cells = <0x1>;
 		#size-cells = <0x1>;
 		ranges = <0x0 0x0 0x0 0xffffffff>;
 		compatible = "simple-bus";
 
+		rpm_msg_ram: memory@60000 {
+			compatible = "qcom,rpm-msg-ram";
+			reg = <0x60000 0x8000>;
+		};
+
 		pinctrl: qcom,tlmm@1000000 {
 			compatible = "qcom,tlmm-apq8016";
 			reg = <0x1000000 0x400000>;

arch/arm/dts/dragonboard820c-uboot.dtsi

@@ -6,6 +6,10 @@
  */
 
 / {
+	smem {
+		u-boot,dm-pre-reloc;
+	};
+
 	soc {
 		u-boot,dm-pre-reloc;
 

arch/arm/dts/dragonboard820c.dts

@@ -28,11 +28,27 @@
 		reg = <0 0x80000000 0 0xc0000000>;
 	};
 
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		smem_mem: smem_region@86300000 {
+			reg = <0x0 0x86300000 0x0 0x200000>;
+			no-map;
+		};
+	};
+
 	psci {
 		compatible = "arm,psci-1.0";
 		method = "smc";
 	};
 
+	smem {
+		compatible = "qcom,smem";
+		memory-region = <&smem_mem>;
+	};
+
 	soc: soc {
 		#address-cells = <1>;
 		#size-cells = <1>;

arch/arm/dts/fsl-ls1012a-2g5rdb.dts

@@ -40,3 +40,7 @@
 &duart0 {
 	status = "okay";
 };
+
+&sata {
+	status = "okay";
+};

arch/arm/dts/fsl-ls1012a-qds.dtsi

@@ -125,3 +125,7 @@
 	status = "okay";
 	phy_type = "ulpi";
 };
+
+&sata {
+	status = "okay";
+};

arch/arm/dts/fsl-ls1012a-rdb.dtsi

@@ -34,3 +34,7 @@
 &duart0 {
 	status = "okay";
 };
+
+&sata {
+	status = "okay";
+};

arch/arm/dts/fsl-ls1012a.dtsi

@@ -134,6 +134,14 @@
 				  0x82000000 0x0 0x40000000 0x40 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
 		};
 
+		sata: sata@3200000 {
+			compatible = "fsl,ls1012a-ahci";
+			reg = <0x0 0x3200000 0x0 0x10000>;
+			interrupts = <0 69 4>;
+			clocks = <&clockgen 4 0>;
+			status = "disabled";
+		};
+
 		usb0: usb2@8600000 {
 			compatible = "fsl-usb2-dr-v2.5", "fsl-usb2-dr";
 			reg = <0x0 0x8600000 0x0 0x1000>;

arch/arm/dts/imx6ull-colibri.dts

@@ -0,0 +1,550 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2018 Toradex AG
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include "imx6ull.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX6ULL";
+	compatible = "toradex,imx6ull-colibri", "fsl,imx6ull";
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	reg_module_3v3: regulator-module-3v3 {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-name = "+V3.3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_module_3v3_avdd: regulator-module-3v3-avdd {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-name = "+V3.3_AVDD_AUDIO";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_sd1_vmmc: regulator-sd1-vmmc {
+		compatible = "regulator-gpio";
+		gpio = <&gpio5 9 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_snvs_reg_sd>;
+		regulator-always-on;
+		regulator-name = "+V3.3_1.8_SD";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		states = <1800000 0x1 3300000 0x0>;
+		vin-supply = <&reg_module_3v3>;
+	};
+};
+
+&adc1 {
+	num-channels = <10>;
+	vref-supply = <&reg_module_3v3_avdd>;
+};
+
+/* Colibri SPI */
+&ecspi1 {
+	cs-gpios = <&gpio3 26 GPIO_ACTIVE_HIGH>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1 &pinctrl_ecspi1_cs>;
+};
+
+&fec2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet2>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy1>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy1: ethernet-phy@2 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			max-speed = <100>;
+			reg = <2>;
+		};
+	};
+};
+
+&gpmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpmi_nand>;
+	nand-on-flash-bbt;
+	nand-ecc-mode = "hw";
+	nand-ecc-strength = <8>;
+	nand-ecc-step-size = <512>;
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	sda-gpios = <&gpio1 29 GPIO_ACTIVE_LOW>;
+	scl-gpios = <&gpio1 28 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_gpio>;
+	sda-gpios = <&gpio1 31 GPIO_ACTIVE_LOW>;
+	scl-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	ad7879@2c {
+		compatible = "adi,ad7879-1";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_snvs_ad7879_int>;
+		reg = <0x2c>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+		touchscreen-max-pressure = <4096>;
+		adi,resistance-plate-x = <120>;
+		adi,first-conversion-delay = /bits/ 8 <3>;
+		adi,acquisition-time = /bits/ 8 <1>;
+		adi,median-filter-size = /bits/ 8 <2>;
+		adi,averaging = /bits/ 8 <1>;
+		adi,conversion-interval = /bits/ 8 <255>;
+	};
+};
+
+&lcdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lcdif_dat
+		     &pinctrl_lcdif_ctrl>;
+};
+
+&pwm4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm4>;
+	#pwm-cells = <3>;
+};
+
+&pwm5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm5>;
+	#pwm-cells = <3>;
+};
+
+&pwm6 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm6>;
+	#pwm-cells = <3>;
+};
+
+&pwm7 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm7>;
+	#pwm-cells = <3>;
+};
+
+&sdma {
+	status = "okay";
+};
+
+&snvs_pwrkey {
+	status = "disabled";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1 &pinctrl_uart1_ctrl1>;
+	fsl,uart-has-rtscts;
+	fsl,dte-mode;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	fsl,uart-has-rtscts;
+	fsl,dte-mode;
+};
+
+&uart5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart5>;
+	fsl,dte-mode;
+};
+
+&usbotg1 {
+	dr_mode = "otg";
+	srp-disable;
+	hnp-disable;
+	adp-disable;
+};
+
+&usbotg2 {
+	dr_mode = "host";
+};
+
+&usdhc1 {
+	assigned-clocks = <&clks IMX6UL_CLK_USDHC1_SEL>, <&clks IMX6UL_CLK_USDHC1>;
+	assigned-clock-parents = <&clks IMX6UL_CLK_PLL2_PFD2>;
+	assigned-clock-rates = <0>, <198000000>;
+};
+
+&iomuxc {
+	pinctrl_gpio1: gpio1-grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET1_RX_DATA0__GPIO2_IO00	0x74 /* SODIMM 55 */
+			MX6UL_PAD_ENET1_RX_DATA1__GPIO2_IO01	0x74 /* SODIMM 63 */
+			MX6UL_PAD_UART3_RX_DATA__GPIO1_IO25	0X14 /* SODIMM 77 */
+			MX6UL_PAD_JTAG_TCK__GPIO1_IO14		0x14 /* SODIMM 99 */
+			MX6UL_PAD_NAND_CE1_B__GPIO4_IO14	0x14 /* SODIMM 133 */
+			MX6UL_PAD_UART3_TX_DATA__GPIO1_IO24	0x14 /* SODIMM 135 */
+			MX6UL_PAD_UART3_CTS_B__GPIO1_IO26	0x14 /* SODIMM 100 */
+			MX6UL_PAD_JTAG_TRST_B__GPIO1_IO15	0x14 /* SODIMM 102 */
+			MX6UL_PAD_ENET1_RX_ER__GPIO2_IO07	0x14 /* SODIMM 104 */
+			MX6UL_PAD_UART3_RTS_B__GPIO1_IO27	0x14 /* SODIMM 186 */
+		>;
+	};
+
+	pinctrl_gpio2: gpio2-grp { /* Camera */
+		fsl,pins = <
+			MX6UL_PAD_CSI_DATA04__GPIO4_IO25	0x74 /* SODIMM 69 */
+			MX6UL_PAD_CSI_MCLK__GPIO4_IO17		0x14 /* SODIMM 75 */
+			MX6UL_PAD_CSI_DATA06__GPIO4_IO27	0x14 /* SODIMM 85 */
+			MX6UL_PAD_CSI_PIXCLK__GPIO4_IO18	0x14 /* SODIMM 96 */
+			MX6UL_PAD_CSI_DATA05__GPIO4_IO26	0x14 /* SODIMM 98 */
+		>;
+	};
+
+	pinctrl_gpio3: gpio3-grp { /* CAN2 */
+		fsl,pins = <
+			MX6UL_PAD_ENET1_RX_EN__GPIO2_IO02	0x14 /* SODIMM 178 */
+			MX6UL_PAD_ENET1_TX_DATA0__GPIO2_IO03	0x14 /* SODIMM 188 */
+		>;
+	};
+
+	pinctrl_gpio4: gpio4-grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_DATA07__GPIO4_IO28	0x74 /* SODIMM 65 */
+		>;
+	};
+
+	pinctrl_gpio5: gpio5-grp { /* ATMEL MXT TOUCH */
+		fsl,pins = <
+			MX6UL_PAD_JTAG_MOD__GPIO1_IO10		0x74 /* SODIMM 106 */
+		>;
+	};
+
+	pinctrl_gpio6: gpio6-grp { /* Wifi pins */
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO03__GPIO1_IO03	0x14 /* SODIMM 89 */
+			MX6UL_PAD_CSI_DATA02__GPIO4_IO23	0x14 /* SODIMM 79 */
+			MX6UL_PAD_CSI_VSYNC__GPIO4_IO19		0x14 /* SODIMM 81 */
+			MX6UL_PAD_CSI_DATA03__GPIO4_IO24	0x14 /* SODIMM 97 */
+			MX6UL_PAD_CSI_DATA00__GPIO4_IO21	0x14 /* SODIMM 101 */
+			MX6UL_PAD_CSI_DATA01__GPIO4_IO22	0x14 /* SODIMM 103 */
+			MX6UL_PAD_CSI_HSYNC__GPIO4_IO20		0x14 /* SODIMM 94 */
+		>;
+	};
+
+	pinctrl_can_int: canint-grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET1_TX_DATA1__GPIO2_IO04	0X14 /* SODIMM 73 */
+		>;
+	};
+
+	pinctrl_enet2: enet2-grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO06__ENET2_MDIO	0x1b0b0
+			MX6UL_PAD_GPIO1_IO07__ENET2_MDC		0x1b0b0
+			MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00	0x1b0b0
+			MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01	0x1b0b0
+			MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN	0x1b0b0
+			MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER	0x1b0b0
+			MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2	0x4001b031
+			MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00	0x1b0b0
+			MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01	0x1b0b0
+			MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN	0x1b0b0
+		>;
+	};
+
+	pinctrl_ecspi1_cs: ecspi1-cs-grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA21__GPIO3_IO26	0x000a0
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1-grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA20__ECSPI1_SCLK	0x000a0
+			MX6UL_PAD_LCD_DATA22__ECSPI1_MOSI	0x000a0
+			MX6UL_PAD_LCD_DATA23__ECSPI1_MISO	0x100a0
+		>;
+	};
+
+	pinctrl_flexcan2: flexcan2-grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET1_TX_DATA0__FLEXCAN2_RX	0x1b020
+			MX6UL_PAD_ENET1_RX_EN__FLEXCAN2_TX	0x1b020
+		>;
+	};
+
+	pinctrl_gpio_bl_on: gpio-bl-on-grp {
+		fsl,pins = <
+			MX6UL_PAD_JTAG_TMS__GPIO1_IO11		0x000a0
+		>;
+	};
+
+	pinctrl_gpmi_nand: gpmi-nand-grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_DATA00__RAWNAND_DATA00	0x100a9
+			MX6UL_PAD_NAND_DATA01__RAWNAND_DATA01	0x100a9
+			MX6UL_PAD_NAND_DATA02__RAWNAND_DATA02	0x100a9
+			MX6UL_PAD_NAND_DATA03__RAWNAND_DATA03	0x100a9
+			MX6UL_PAD_NAND_DATA04__RAWNAND_DATA04	0x100a9
+			MX6UL_PAD_NAND_DATA05__RAWNAND_DATA05	0x100a9
+			MX6UL_PAD_NAND_DATA06__RAWNAND_DATA06	0x100a9
+			MX6UL_PAD_NAND_DATA07__RAWNAND_DATA07	0x100a9
+			MX6UL_PAD_NAND_CLE__RAWNAND_CLE		0x100a9
+			MX6UL_PAD_NAND_ALE__RAWNAND_ALE		0x100a9
+			MX6UL_PAD_NAND_RE_B__RAWNAND_RE_B	0x100a9
+			MX6UL_PAD_NAND_WE_B__RAWNAND_WE_B	0x100a9
+			MX6UL_PAD_NAND_CE0_B__RAWNAND_CE0_B	0x100a9
+			MX6UL_PAD_NAND_READY_B__RAWNAND_READY_B	0x100a9
+		>;
+	};
+
+	pinctrl_i2c1: i2c1-grp {
+		fsl,pins = <
+			MX6UL_PAD_UART4_TX_DATA__I2C1_SCL 0x4001b8b0
+			MX6UL_PAD_UART4_RX_DATA__I2C1_SDA 0x4001b8b0
+		>;
+	};
+
+	pinctrl_i2c1_gpio: i2c1-gpio-grp {
+		fsl,pins = <
+			MX6UL_PAD_UART4_TX_DATA__GPIO1_IO28 0x4001b8b0
+			MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29 0x4001b8b0
+		>;
+	};
+
+	pinctrl_i2c2: i2c2-grp {
+		fsl,pins = <
+			MX6UL_PAD_UART5_TX_DATA__I2C2_SCL 0x4001b8b0
+			MX6UL_PAD_UART5_RX_DATA__I2C2_SDA 0x4001b8b0
+		>;
+	};
+
+	pinctrl_i2c2_gpio: i2c2-gpio-grp {
+		fsl,pins = <
+			MX6UL_PAD_UART5_TX_DATA__GPIO1_IO30 0x4001b8b0
+			MX6UL_PAD_UART5_RX_DATA__GPIO1_IO31 0x4001b8b0
+		>;
+	};
+
+	pinctrl_lcdif_dat: lcdif-dat-grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA00__LCDIF_DATA00  0x00079
+			MX6UL_PAD_LCD_DATA01__LCDIF_DATA01  0x00079
+			MX6UL_PAD_LCD_DATA02__LCDIF_DATA02  0x00079
+			MX6UL_PAD_LCD_DATA03__LCDIF_DATA03  0x00079
+			MX6UL_PAD_LCD_DATA04__LCDIF_DATA04  0x00079
+			MX6UL_PAD_LCD_DATA05__LCDIF_DATA05  0x00079
+			MX6UL_PAD_LCD_DATA06__LCDIF_DATA06  0x00079
+			MX6UL_PAD_LCD_DATA07__LCDIF_DATA07  0x00079
+			MX6UL_PAD_LCD_DATA08__LCDIF_DATA08  0x00079
+			MX6UL_PAD_LCD_DATA09__LCDIF_DATA09  0x00079
+			MX6UL_PAD_LCD_DATA10__LCDIF_DATA10  0x00079
+			MX6UL_PAD_LCD_DATA11__LCDIF_DATA11  0x00079
+			MX6UL_PAD_LCD_DATA12__LCDIF_DATA12  0x00079
+			MX6UL_PAD_LCD_DATA13__LCDIF_DATA13  0x00079
+			MX6UL_PAD_LCD_DATA14__LCDIF_DATA14  0x00079
+			MX6UL_PAD_LCD_DATA15__LCDIF_DATA15  0x00079
+			MX6UL_PAD_LCD_DATA16__LCDIF_DATA16  0x00079
+			MX6UL_PAD_LCD_DATA17__LCDIF_DATA17  0x00079
+		>;
+	};
+
+	pinctrl_lcdif_ctrl: lcdif-ctrl-grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_CLK__LCDIF_CLK	    0x00079
+			MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE  0x00079
+			MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC    0x00079
+			MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC    0x00079
+		>;
+	};
+
+	pinctrl_pwm4: pwm4-grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_WP_B__PWM4_OUT	0x00079
+		>;
+	};
+
+	pinctrl_pwm5: pwm5-grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_DQS__PWM5_OUT	0x00079
+		>;
+	};
+
+	pinctrl_pwm6: pwm6-grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET1_TX_EN__PWM6_OUT	0x00079
+		>;
+	};
+
+	pinctrl_pwm7: pwm7-grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET1_TX_CLK__PWM7_OUT	0x00079
+		>;
+	};
+
+	pinctrl_uart1: uart1-grp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_TX_DATA__UART1_DTE_RX	0x1b0b1
+			MX6UL_PAD_UART1_RX_DATA__UART1_DTE_TX	0x1b0b1
+			MX6UL_PAD_UART1_RTS_B__UART1_DTE_CTS	0x1b0b1
+			MX6UL_PAD_UART1_CTS_B__UART1_DTE_RTS	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart1_ctrl1: uart1-ctrl1-grp { /* Additional DTR, DCD */
+		fsl,pins = <
+			MX6UL_PAD_JTAG_TDI__GPIO1_IO13		0x1b0b1 /* DCD */
+			MX6UL_PAD_LCD_DATA18__GPIO3_IO23	0x1b0b1 /* DSR */
+			MX6UL_PAD_JTAG_TDO__GPIO1_IO12		0x1b0b1 /* DTR */
+			MX6UL_PAD_LCD_DATA19__GPIO3_IO24        0x1b0b1 /* RI */
+		>;
+	};
+
+	pinctrl_uart2: uart2-grp {
+		fsl,pins = <
+			MX6UL_PAD_UART2_TX_DATA__UART2_DTE_RX	0x1b0b1
+			MX6UL_PAD_UART2_RX_DATA__UART2_DTE_TX	0x1b0b1
+			MX6UL_PAD_UART2_CTS_B__UART2_DTE_RTS	0x1b0b1
+			MX6UL_PAD_UART2_RTS_B__UART2_DTE_CTS	0x1b0b1
+		>;
+	};
+	pinctrl_uart5: uart5-grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO04__UART5_DTE_RX	0x1b0b1
+			MX6UL_PAD_GPIO1_IO05__UART5_DTE_TX	0x1b0b1
+		>;
+	};
+
+	pinctrl_usbh_reg: gpio-usbh-reg {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO02__GPIO1_IO02	0x1b0b1 /* SODIMM 129 USBH PEN */
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1-grp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x17059
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x10059
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x17059
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x17059
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x17059
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x17059
+		>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1-100mhz-grp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x170b9
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x100b9
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170b9
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170b9
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170b9
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x170b9
+		>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1-200mhz-grp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x170f9
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x100f9
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170b9
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170b9
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170b9
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x170b9
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2-grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_DATA00__USDHC2_DATA0	0x17059
+			MX6UL_PAD_CSI_DATA01__USDHC2_DATA1	0x17059
+			MX6UL_PAD_CSI_DATA02__USDHC2_DATA2	0x17059
+			MX6UL_PAD_CSI_DATA03__USDHC2_DATA3	0x17059
+			MX6UL_PAD_CSI_HSYNC__USDHC2_CMD		0x17059
+			MX6UL_PAD_CSI_VSYNC__USDHC2_CLK		0x17059
+		>;
+	};
+};
+
+&iomuxc_snvs {
+	pinctrl_snvs_gpio1: snvs-gpio1-grp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER6__GPIO5_IO06	0x14 /* SODIMM 93 */
+			MX6ULL_PAD_SNVS_TAMPER3__GPIO5_IO03	0x14 /* SODIMM 95 */
+			MX6ULL_PAD_BOOT_MODE0__GPIO5_IO10	0x74 /* SODIMM 105 */
+			MX6ULL_PAD_SNVS_TAMPER5__GPIO5_IO05	0x14 /* SODIMM 131 USBH OC */
+			MX6ULL_PAD_SNVS_TAMPER8__GPIO5_IO08	0x74 /* SODIMM 138 */
+		>;
+	};
+
+	pinctrl_snvs_gpio2: snvs-gpio2-grp { /* ATMEL MXT TOUCH */
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER4__GPIO5_IO04	0x74 /* SODIMM 107 */
+		>;
+	};
+
+	pinctrl_snvs_gpio3: snvs-gpio3-grp { /* Wifi pins */
+		fsl,pins = <
+			MX6ULL_PAD_BOOT_MODE1__GPIO5_IO11	0x14 /* SODIMM 127 */
+		>;
+	};
+
+	pinctrl_snvs_ad7879_int: snvs-ad7879-int { /* TOUCH Interrupt */
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER7__GPIO5_IO07	0x1b0b0
+		>;
+	};
+
+	pinctrl_snvs_reg_sd: snvs-reg-sd-grp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER9__GPIO5_IO09	0x4001b8b0
+		>;
+	};
+
+	pinctrl_snvs_usbc_det: snvs-usbc-det-grp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER2__GPIO5_IO02	0x1b0b0
+		>;
+	};
+
+	pinctrl_snvs_gpiokeys: snvs-gpiokeys-grp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER1__GPIO5_IO01	0x130b0
+		>;
+	};
+
+	pinctrl_snvs_usdhc1_cd: snvs-usdhc1-cd-grp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER0__GPIO5_IO00	0x1b0b0 /* CD */
+		>;
+	};
+
+	pinctrl_snvs_wifi_pdn: snvs-wifi-pdn-grp {
+		fsl,pins = <
+			MX6ULL_PAD_BOOT_MODE1__GPIO5_IO11	0x14
+		>;
+	};
+};
+

arch/arm/dts/imx6ull.dtsi

@@ -190,7 +190,7 @@
 		};
 
 		gpmi: gpmi-nand@01806000{
-			compatible = "fsl,imx6ull-gpmi-nand", "fsl, imx6ul-gpmi-nand";
+			compatible = "fsl,imx6q-gpmi-nand";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			reg = <0x01806000 0x2000>, <0x01808000 0x4000>;

arch/arm/dts/logicpd-som-lv-37xx-devkit.dts

@@ -8,262 +8,10 @@
 
 #include "omap36xx.dtsi"
 #include "logicpd-som-lv.dtsi"
+#include "logicpd-som-lv-baseboard.dtsi"
 #include "omap-gpmc-smsc9221.dtsi"
 
 / {
 	model = "LogicPD Zoom DM3730 SOM-LV Development Kit";
 	compatible = "logicpd,dm3730-som-lv-devkit", "ti,omap3630", "ti,omap3";
-
-	chosen {
-		stdout-path = &uart1;
-	};
-
-	gpio_keys {
-		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&gpio_key_pins>;
-
-		sysboot2 {
-			label = "gpio3";
-			gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;	/* gpio_111 / uP_GPIO_3 */
-			linux,code = <BTN_0>;
-			wakeup-source;
-		};
-	};
-
-	sound {
-		compatible = "ti,omap-twl4030";
-		ti,model = "omap3logic";
-		ti,mcbsp = <&mcbsp2>;
-	};
-
-	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&led_pins &led_pins_wkup>;
-
-		led1 {
-			label = "led1";
-			gpios = <&gpio5 5 GPIO_ACTIVE_LOW>;	/* gpio133 */
-			linux,default-trigger = "cpu0";
-		};
-
-		led2 {
-			label = "led2";
-			gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;	/* gpio11 */
-			linux,default-trigger = "none";
-		};
-	};
-};
-
-&vaux1 {
-	regulator-min-microvolt = <3000000>;
-	regulator-max-microvolt = <3000000>;
-};
-
-&vaux4 {
-	regulator-min-microvolt = <1800000>;
-	regulator-max-microvolt = <1800000>;
-};
-
-&mcbsp2 {
-	status = "okay";
-};
-
-&charger {
-	ti,bb-uvolt = <3200000>;
-	ti,bb-uamp = <150>;
-};
-
-&gpmc {
-	ranges = <1 0 0x08000000 0x1000000>;	/* CS1: 16MB for LAN9221 */
-
-	ethernet@gpmc {
-		pinctrl-names = "default";
-		pinctrl-0 = <&lan9221_pins>;
-		interrupt-parent = <&gpio5>;
-		interrupts = <24 IRQ_TYPE_LEVEL_LOW>;		/* gpio_152 */
-		reg = <1 0 0xff>;
-	};
-};
-
-&vpll2 {
-	regulator-always-on;
-};
-
-&dss {
-	status = "ok";
-	vdds_dsi-supply = <&vpll2>;
-	vdda_video-supply = <&video_reg>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&dss_dpi_pins1>;
-	port {
-		dpi_out: endpoint {
-			remote-endpoint = <&lcd_in>;
-			data-lines = <16>;
-		};
-	};
-};
-
-/ {
-	aliases {
-		display0 = &lcd0;
-	};
-
-	video_reg: video_reg {
-		compatible = "regulator-fixed";
-		regulator-name = "fixed-supply";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-	};
-
-	lcd0: display@0 {
-		compatible = "panel-dpi";
-		label = "28";
-		status = "okay";
-		/* default-on; */
-		pinctrl-names = "default";
-		pinctrl-0 = <&lcd_enable_pin>;
-		enable-gpios = <&gpio5 27 GPIO_ACTIVE_HIGH>;	/* gpio155, lcd INI */
-		port {
-			lcd_in: endpoint {
-				remote-endpoint = <&dpi_out>;
-			};
-		};
-
-		panel-timing {
-			clock-frequency = <9000000>;
-			hactive = <480>;
-			vactive = <272>;
-			hfront-porch = <3>;
-			hback-porch = <2>;
-			hsync-len = <42>;
-			vback-porch = <3>;
-			vfront-porch = <2>;
-			vsync-len = <11>;
-			hsync-active = <1>;
-			vsync-active = <1>;
-			de-active = <1>;
-			pixelclk-active = <0>;
-		};
-	};
-
-	bl: backlight {
-		compatible = "pwm-backlight";
-		pinctrl-names = "default";
-		pinctrl-0 = <&backlight_pins>;
-		pwms = <&twl_pwm 0 5000000>;
-		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
-		default-brightness-level = <7>;
-		enable-gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; /* gpio_8 */
-	};
-};
-
-&mmc1 {
-	interrupts-extended = <&intc 83 &omap3_pmx_core 0x11a>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc1_pins>;
-	vmmc-supply = <&vmmc1>;
-	bus-width = <4>;
-	cap-power-off-card;
-};
-
-&mmc2 {
-	status = "disabled";
-};
-
-&omap3_pmx_core {
-	gpio_key_pins: pinmux_gpio_key_pins {
-		pinctrl-single,pins = <
-			OMAP3_CORE1_IOPAD(0x212e, PIN_INPUT_PULLUP | MUX_MODE4)	/* cam_xclkb.gpio_111 / uP_GPIO_3*/
-		>;
-	};
-
-	led_pins: pinmux_led_pins {
-		pinctrl-single,pins = <
-			OMAP3_CORE1_IOPAD(0x215e, PIN_OUTPUT_PULLUP | MUX_MODE4)	/* sdmmc2_dat1.gpio_133 / uP_GPIO_0 */
-		>;
-	};
-
-	lan9221_pins: pinmux_lan9221_pins {
-		pinctrl-single,pins = <
-			OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLUP | MUX_MODE4)	/* mcbsp4_clkx.gpio_152 */
-		>;
-	};
-
-	mmc1_pins: pinmux_mmc1_pins {
-		pinctrl-single,pins = <
-			OMAP3_CORE1_IOPAD(0x2144, PIN_OUTPUT | MUX_MODE0)	/* sdmmc1_clk.sdmmc1_clk */
-			OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT | MUX_MODE0)	/* sdmmc1_cmd.sdmmc1_cmd */
-			OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT | MUX_MODE0)	/* sdmmc1_dat0.sdmmc1_dat0 */
-			OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT | MUX_MODE0)	/* sdmmc1_dat1.sdmmc1_dat1 */
-			OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT | MUX_MODE0)	/* sdmmc1_dat2.sdmmc1_dat2 */
-			OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT | MUX_MODE0)	/* sdmmc1_dat3.sdmmc1_dat3 */
-			OMAP3_CORE1_IOPAD(0x2132, PIN_INPUT_PULLUP | MUX_MODE4)	/* cam_strobe.gpio_126 */
-			OMAP3_CORE1_IOPAD(0x212c, PIN_INPUT_PULLUP | MUX_MODE4)	/* cam_d11.gpio_110 */
-		>;
-	};
-
-	lcd_enable_pin: pinmux_lcd_enable_pin {
-		pinctrl-single,pins = <
-			OMAP3_CORE1_IOPAD(0x218a, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4)       /* mcbsp4_fs.gpio_155 */
-		>;
-	};
-
-	dss_dpi_pins1: pinmux_dss_dpi_pins1 {
-		pinctrl-single,pins = <
-			OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_pclk.dss_pclk */
-			OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_hsync.dss_hsync */
-			OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_vsync.dss_vsync */
-			OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_acbias.dss_acbias */
-
-			OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data0.dss_data0 */
-			OMAP3_CORE1_IOPAD(0x20de, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data1.dss_data1 */
-			OMAP3_CORE1_IOPAD(0x20e0, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data2.dss_data2 */
-			OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data3.dss_data3 */
-			OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data4.dss_data4 */
-			OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data5.dss_data5 */
-			OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data6.dss_data6 */
-			OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data7.dss_data7 */
-			OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data8.dss_data8 */
-			OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data9.dss_data9 */
-			OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data10.dss_data10 */
-			OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data11.dss_data11 */
-			OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data12.dss_data12 */
-			OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data13.dss_data13 */
-			OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data14.dss_data14 */
-			OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data15.dss_data15 */
-		>;
-	};
-};
-
-&omap3_pmx_wkup {
-	led_pins_wkup: pinmux_led_pins_wkup {
-		pinctrl-single,pins = <
-			OMAP3_WKUP_IOPAD(0x2a24, PIN_OUTPUT_PULLUP | MUX_MODE4)	/* jtag_emu0.gpio_11 / uP_GPIO_1 */
-		>;
-	};
-
-	backlight_pins: pinmux_backlight_pins {
-		pinctrl-single,pins = <
-			OMAP3_WKUP_IOPAD(0x2a16, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4)       /* sys_boot6.gpio_8 */
-		>;
-	};
-};
-
-
-&uart1 {
-	interrupts-extended = <&intc 72 &omap3_pmx_core OMAP3_UART1_RX>;
-};
-
-/* Wired to the tps65950 on the SOM, only the USB connector is on the devkit */
-&usb_otg_hs {
-	pinctrl-names = "default";
-	pinctrl-0 = <&hsusb_otg_pins>;
-	interface-type = <0>;
-	usb-phy = <&usb2_phy>;
-	phys = <&usb2_phy>;
-	phy-names = "usb2-phy";
-	mode = <3>;
-	power = <50>;
 };

arch/arm/dts/logicpd-som-lv-baseboard.dtsi

@@ -0,0 +1,256 @@
+/*
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/ {
+	gpio_keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_key_pins>;
+
+		sysboot2 {
+			label = "gpio3";
+			gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;	/* gpio_111 / uP_GPIO_3 */
+			linux,code = <BTN_0>;
+			wakeup-source;
+		};
+	};
+
+	sound {
+		compatible = "ti,omap-twl4030";
+		ti,model = "omap3logic";
+		ti,mcbsp = <&mcbsp2>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_pins &led_pins_wkup>;
+
+		led1 {
+			label = "led1";
+			gpios = <&gpio5 5 GPIO_ACTIVE_LOW>;	/* gpio133 */
+			linux,default-trigger = "cpu0";
+		};
+
+		led2 {
+			label = "led2";
+			gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;	/* gpio11 */
+			linux,default-trigger = "none";
+		};
+	};
+};
+
+&vaux1 {
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+};
+
+&vaux4 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+};
+
+&mcbsp2 {
+	status = "okay";
+};
+
+&charger {
+	ti,bb-uvolt = <3200000>;
+	ti,bb-uamp = <150>;
+};
+
+&gpmc {
+	ranges = <0 0 0x30000000 0x1000000	/* CS0: 16MB for NAND */
+		  1 0 0x2c000000 0x1000000	/* CS1: 16MB for LAN9221 */
+		  2 0 0x10000000 0x2000000>;    /* CS2: 32MB for NOR */
+
+	ethernet@gpmc {
+		pinctrl-names = "default";
+		pinctrl-0 = <&lan9221_pins>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <24 IRQ_TYPE_LEVEL_LOW>;		/* gpio_152 */
+		reg = <1 0 0xff>;
+	};
+};
+
+&vpll2 {
+	regulator-always-on;
+};
+
+&dss {
+	status = "ok";
+	vdds_dsi-supply = <&vpll2>;
+	vdda_video-supply = <&video_reg>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&dss_dpi_pins1>;
+	port {
+		dpi_out: endpoint {
+			remote-endpoint = <&lcd_in>;
+			data-lines = <16>;
+		};
+	};
+};
+
+/ {
+	aliases {
+		display0 = &lcd0;
+	};
+
+	video_reg: video_reg {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-supply";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	lcd0: display@0 {
+		compatible = "panel-dpi";
+		label = "28";
+		status = "okay";
+		/* default-on; */
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_enable_pin>;
+		enable-gpios = <&gpio5 27 GPIO_ACTIVE_HIGH>;	/* gpio155, lcd INI */
+		port {
+			lcd_in: endpoint {
+				remote-endpoint = <&dpi_out>;
+			};
+		};
+
+		panel-timing {
+			clock-frequency = <9000000>;
+			hactive = <480>;
+			vactive = <272>;
+			hfront-porch = <3>;
+			hback-porch = <2>;
+			hsync-len = <42>;
+			vback-porch = <3>;
+			vfront-porch = <2>;
+			vsync-len = <11>;
+			hsync-active = <1>;
+			vsync-active = <1>;
+			de-active = <1>;
+			pixelclk-active = <0>;
+		};
+	};
+
+	bl: backlight {
+		compatible = "pwm-backlight";
+		pinctrl-names = "default";
+		pinctrl-0 = <&backlight_pins>;
+		pwms = <&twl_pwm 0 5000000>;
+		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+		default-brightness-level = <7>;
+		enable-gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; /* gpio_8 */
+	};
+};
+
+&mmc1 {
+	interrupts-extended = <&intc 83 &omap3_pmx_core 0x11a>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	wp-gpios = <&gpio4 30 GPIO_ACTIVE_HIGH>;		/* gpio_126 */
+	cd-gpios = <&gpio4 14 IRQ_TYPE_LEVEL_LOW>;		/* gpio_110 */
+	vmmc-supply = <&vmmc1>;
+	bus-width = <4>;
+	cap-power-off-card;
+};
+
+&omap3_pmx_core {
+	gpio_key_pins: pinmux_gpio_key_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x212e, PIN_INPUT_PULLUP | MUX_MODE4)	/* cam_xclkb.gpio_111 / uP_GPIO_3*/
+		>;
+	};
+
+	led_pins: pinmux_led_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x215e, PIN_OUTPUT_PULLUP | MUX_MODE4)	/* sdmmc2_dat1.gpio_133 / uP_GPIO_0 */
+		>;
+	};
+
+	lan9221_pins: pinmux_lan9221_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLUP | MUX_MODE4)	/* mcbsp4_clkx.gpio_152 */
+		>;
+	};
+
+	mmc1_pins: pinmux_mmc1_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2144, PIN_OUTPUT | MUX_MODE0)	/* sdmmc1_clk.sdmmc1_clk */
+			OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT | MUX_MODE0)	/* sdmmc1_cmd.sdmmc1_cmd */
+			OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT | MUX_MODE0)	/* sdmmc1_dat0.sdmmc1_dat0 */
+			OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT | MUX_MODE0)	/* sdmmc1_dat1.sdmmc1_dat1 */
+			OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT | MUX_MODE0)	/* sdmmc1_dat2.sdmmc1_dat2 */
+			OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT | MUX_MODE0)	/* sdmmc1_dat3.sdmmc1_dat3 */
+			OMAP3_CORE1_IOPAD(0x2132, PIN_INPUT_PULLUP | MUX_MODE4)	/* cam_strobe.gpio_126 */
+			OMAP3_CORE1_IOPAD(0x212c, PIN_INPUT_PULLUP | MUX_MODE4)	/* cam_d11.gpio_110 */
+		>;
+	};
+
+	lcd_enable_pin: pinmux_lcd_enable_pin {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x218a, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4)       /* mcbsp4_fs.gpio_155 */
+		>;
+	};
+
+	dss_dpi_pins1: pinmux_dss_dpi_pins1 {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_pclk.dss_pclk */
+			OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_hsync.dss_hsync */
+			OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_vsync.dss_vsync */
+			OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_acbias.dss_acbias */
+
+			OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data0.dss_data0 */
+			OMAP3_CORE1_IOPAD(0x20de, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data1.dss_data1 */
+			OMAP3_CORE1_IOPAD(0x20e0, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data2.dss_data2 */
+			OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data3.dss_data3 */
+			OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data4.dss_data4 */
+			OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data5.dss_data5 */
+			OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data6.dss_data6 */
+			OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data7.dss_data7 */
+			OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data8.dss_data8 */
+			OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data9.dss_data9 */
+			OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data10.dss_data10 */
+			OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data11.dss_data11 */
+			OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data12.dss_data12 */
+			OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data13.dss_data13 */
+			OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data14.dss_data14 */
+			OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data15.dss_data15 */
+		>;
+	};
+};
+
+&omap3_pmx_wkup {
+	led_pins_wkup: pinmux_led_pins_wkup {
+		pinctrl-single,pins = <
+			OMAP3_WKUP_IOPAD(0x2a24, PIN_OUTPUT_PULLUP | MUX_MODE4)	/* jtag_emu0.gpio_11 / uP_GPIO_1 */
+		>;
+	};
+
+	backlight_pins: pinmux_backlight_pins {
+		pinctrl-single,pins = <
+			OMAP3_WKUP_IOPAD(0x2a16, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4)       /* sys_boot6.gpio_8 */
+		>;
+	};
+};
+
+
+&uart1 {
+	interrupts-extended = <&intc 72 &omap3_pmx_core OMAP3_UART1_RX>;
+};
+
+/* Wired to the tps65950 on the SOM, only the USB connector is on the devkit */
+&usb_otg_hs {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hsusb_otg_pins>;
+	interface-type = <0>;
+	usb-phy = <&usb2_phy>;
+	phys = <&usb2_phy>;
+	phy-names = "usb2-phy";
+	mode = <3>;
+	power = <50>;
+};

arch/arm/dts/logicpd-som-lv.dtsi

@@ -26,7 +26,7 @@
 		gpio = <&gpio1 3 0>;   /* gpio_3 */
 		startup-delay-us = <70000>;
 		enable-active-high;
-		vin-supply = <&vmmc2>;
+		vin-supply = <&vaux3>;
 	};
 
 	/* HS USB Host PHY on PORT 1 */
@@ -35,6 +35,13 @@
 		reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; /* gpio_4 */
 		#phy-cells = <0>;
 	};
+
+	/* fixed 26MHz oscillator */
+	hfclk_26m: oscillator {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <26000000>;
+	};
 };
 
 &gpmc {
@@ -71,26 +78,54 @@
 };
 
 &i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
 	clock-frequency = <2600000>;
 
 	twl: twl@48 {
 		reg = <0x48>;
 		interrupts = <7>; /* SYS_NIRQ cascaded to intc */
 		interrupt-parent = <&intc>;
+		clocks = <&hfclk_26m>;
+		clock-names = "fck";
 		twl_audio: audio {
 			compatible = "ti,twl4030-audio";
 			codec {
+				ti,hs_extmute_gpio = <&gpio2 25 GPIO_ACTIVE_HIGH>;
 			};
 		};
 	};
 };
 
 &i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins>;
 	clock-frequency = <400000>;
 };
 
 &i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c3_pins>;
 	clock-frequency = <400000>;
+
+	touchscreen: tsc2004@48 {
+		compatible = "ti,tsc2004";
+		reg = <0x48>;
+		vio-supply = <&vaux1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&tsc2004_pins>;
+		interrupts-extended = <&gpio5 25 IRQ_TYPE_EDGE_RISING>; /* gpio 153 */
+
+		touchscreen-fuzz-x = <4>;
+		touchscreen-fuzz-y = <7>;
+		touchscreen-fuzz-pressure = <2>;
+		touchscreen-size-x = <4096>;
+		touchscreen-size-y = <4096>;
+		touchscreen-max-pressure = <2048>;
+
+		ti,x-plate-ohms = <280>;
+		ti,esd-recovery-timeout-ms = <8000>;
+	};
 };
 
 &mmc3 {
@@ -189,7 +224,19 @@
 		>;
 	};
 
+	i2c1_pins: pinmux_i2c1_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21ba, PIN_INPUT | MUX_MODE0)        /* i2c1_scl.i2c1_scl */
+			OMAP3_CORE1_IOPAD(0x21bc, PIN_INPUT | MUX_MODE0)        /* i2c1_sda.i2c1_sda */
+			OMAP3_CORE1_IOPAD(0x20ba, PIN_OUTPUT | MUX_MODE4)        /* gpmc_ncs6.gpio_57 */
+		>;
+	};
 
+	tsc2004_pins: pinmux_tsc2004_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2186, PIN_INPUT | MUX_MODE4)	/* mcbsp4_dr.gpio_153 */
+		>;
+	};
 };
 
 &omap3_pmx_wkup {
@@ -202,10 +249,22 @@
 	};
 	wl127x_gpio: pinmux_wl127x_gpio_pin {
 		pinctrl-single,pins = <
-			OMAP3_WKUP_IOPAD(0x2a0c, PIN_INPUT | MUX_MODE4)		/* sys_boot0.gpio_2 */
+			OMAP3_WKUP_IOPAD(0x2a0a, PIN_INPUT | MUX_MODE4)		/* sys_boot0.gpio_2 */
 			OMAP3_WKUP_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE4)	/* sys_boot1.gpio_3 */
 		>;
 	};
+	i2c2_pins: pinmux_i2c2_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21be, PIN_INPUT | MUX_MODE0)	/* i2c2_scl */
+			OMAP3_CORE1_IOPAD(0x21c0, PIN_INPUT | MUX_MODE0)	/* i2c2_sda */
+		>;
+	};
+	i2c3_pins: pinmux_i2c3_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21c2, PIN_INPUT | MUX_MODE0)	/* i2c3_scl */
+			OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT | MUX_MODE0)	/* i2c3_sda */
+		>;
+	};
 };
 
 &omap3_pmx_core2 {
@@ -237,6 +296,11 @@
 #include "twl4030.dtsi"
 #include "twl4030_omap3.dtsi"
 
+&vaux3 {
+	regulator-min-microvolt = <2800000>;
+	regulator-max-microvolt = <2800000>;
+};
+
 &twl {
 	twl_power: power {
 		compatible = "ti,twl4030-power-idle-osc-off", "ti,twl4030-power-idle";

arch/arm/dts/logicpd-torpedo-37xx-devkit.dts

@@ -9,396 +9,69 @@
 #include "omap36xx.dtsi"
 #include "logicpd-torpedo-som.dtsi"
 #include "omap-gpmc-smsc9221.dtsi"
+#include "logicpd-torpedo-baseboard.dtsi"
 
 / {
 	model = "LogicPD Zoom DM3730 Torpedo + Wireless Development Kit";
 	compatible = "logicpd,dm3730-torpedo-devkit", "ti,omap3630", "ti,omap3";
 
-	gpio_keys {
-		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&gpio_key_pins &gpio_key_pins_wkup>;
-
-		sysboot2 {
-			label = "sysboot2";
-			gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;	/* gpio2 */
-			linux,code = <BTN_0>;
-			wakeup-source;
-		};
-
-		sysboot5 {
-			label = "sysboot5";
-			gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;	/* gpio7 */
-			linux,code = <BTN_1>;
-			wakeup-source;
-		};
-
-		gpio1 {
-			label = "gpio1";
-			gpios = <&gpio6 21 GPIO_ACTIVE_LOW>;	/* gpio181 */
-			linux,code = <BTN_2>;
-			wakeup-source;
-		};
-
-		gpio2 {
-			label = "gpio2";
-			gpios = <&gpio6 18 GPIO_ACTIVE_LOW>;	/* gpio178 */
-			linux,code = <BTN_3>;
-			wakeup-source;
-		};
-	};
-
-	sound {
-		compatible = "ti,omap-twl4030";
-		ti,model = "omap3logic";
-		ti,mcbsp = <&mcbsp2>;
-	};
-
-	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&led_pins>;
-
-		led1 {
-			label = "led1";
-			gpios = <&gpio6 20 GPIO_ACTIVE_HIGH>;	/* gpio180 */
-			linux,default-trigger = "cpu0";
-		};
-
-		led2 {
-			label = "led2";
-			gpios = <&gpio6 19 GPIO_ACTIVE_HIGH>;	/* gpio179 */
-			linux,default-trigger = "none";
-		};
-	};
-
-	pwm10: dmtimer-pwm {
-		compatible = "ti,omap-dmtimer-pwm";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pwm_pins>;
-		ti,timers = <&timer10>;
-		#pwm-cells = <3>;
-	};
-
-};
-
-&vaux1 {
-	regulator-min-microvolt = <3000000>;
-	regulator-max-microvolt = <3000000>;
-};
-
-&vaux4 {
-	regulator-min-microvolt = <1800000>;
-	regulator-max-microvolt = <1800000>;
-};
-
-&mcbsp2 {
-	status = "okay";
-};
-
-&charger {
-	ti,bb-uvolt = <3200000>;
-	ti,bb-uamp = <150>;
-};
-
-&gpmc {
-	ranges = <0 0 0x30000000 0x1000000	/* CS0: 16MB for NAND */
-		  1 0 0x2c000000 0x1000000>;	/* CS1: 16MB for LAN9221 */
-
-	ethernet@gpmc {
-		pinctrl-names = "default";
-		pinctrl-0 = <&lan9221_pins>;
-		interrupt-parent = <&gpio5>;
-		interrupts = <1 IRQ_TYPE_LEVEL_LOW>;		/* gpio129 */
-		reg = <1 0 0xff>;
-	};
-};
-
-&vpll2 {
-	regulator-always-on;
-};
-
-&dss {
-	status = "ok";
-	vdds_dsi-supply = <&vpll2>;
-	vdda_video-supply = <&video_reg>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&dss_dpi_pins1>;
-	port {
-		dpi_out: endpoint {
-			remote-endpoint = <&lcd_in>;
-			data-lines = <16>;
-		};
-	};
-};
-
-/ {
-	aliases {
-		display0 = &lcd0;
-	};
-
-	video_reg: video_reg {
-		pinctrl-names = "default";
-		pinctrl-0 = <&panel_pwr_pins>;
+	wl12xx_vmmc: wl12xx_vmmc {
 		compatible = "regulator-fixed";
-		regulator-name = "fixed-supply";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		gpio = <&gpio5 27 GPIO_ACTIVE_HIGH>;	/* gpio155, lcd INI */
-	};
-
-	lcd0: display {
-		compatible = "panel-dpi";
-		label = "15";
-		status = "okay";
-		/* default-on; */
-		pinctrl-names = "default";
-
-		port {
-			lcd_in: endpoint {
-				remote-endpoint = <&dpi_out>;
-			};
-		};
-
-		panel-timing {
-			clock-frequency = <9000000>;
-			hactive = <480>;
-			vactive = <272>;
-			hfront-porch = <3>;
-			hback-porch = <2>;
-			hsync-len = <42>;
-			vback-porch = <3>;
-			vfront-porch = <4>;
-			vsync-len = <11>;
-			hsync-active = <0>;
-			vsync-active = <0>;
-			de-active = <1>;
-			pixelclk-active = <1>;
-		};
-	};
-
-	bl: backlight {
-		compatible = "pwm-backlight";
-		pinctrl-names = "default";
-		pinctrl-0 = <&backlight_pins>;
-		pwms = <&pwm10 0 5000000 0>;
-		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
-		default-brightness-level = <7>;
-		enable-gpios = <&gpio5 26 GPIO_ACTIVE_HIGH>; /* gpio_154 */
+		regulator-name = "vwl1271";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&gpio5 29 0>;   /* gpio157 */
+		startup-delay-us = <70000>;
+		enable-active-high;
+		vin-supply = <&vmmc2>;
 	};
 };
 
-&mmc1 {
-	interrupts-extended = <&intc 83 &omap3_pmx_core 0x11a>;
+/*
+ * Only found on the wireless SOM. For the SOM without wireless, the pins for
+ * MMC3 can be routed with jumpers to the second MMC slot on the devkit and
+ * gpio157 is not connected. So this should be OK to keep common for now,
+ * probably device tree overlays is the way to go with the various SOM and
+ * jumpering combinations for the long run.
+ */
+&mmc3 {
+	interrupts-extended = <&intc 94 &omap3_pmx_core2 0x46>;
+	pinctrl-0 = <&mmc3_pins &mmc3_core2_pins>;
 	pinctrl-names = "default";
-	pinctrl-0 = <&mmc1_pins &mmc1_cd>;
-	cd-gpios = <&gpio4 31 IRQ_TYPE_LEVEL_LOW>;		/* gpio127 */
-	vmmc-supply = <&vmmc1>;
+	vmmc-supply = <&wl12xx_vmmc>;
+	non-removable;
 	bus-width = <4>;
 	cap-power-off-card;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	wlcore: wlcore@2 {
+		compatible = "ti,wl1283";
+		reg = <2>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <24 IRQ_TYPE_LEVEL_HIGH>; /* gpio 152 */
+		ref-clock-frequency = <26000000>;
+		tcxo-clock-frequency = <26000000>;
+	};
 };
 
 &omap3_pmx_core {
-	gpio_key_pins: pinmux_gpio_key_pins {
+	mmc3_pins: pinmux_mm3_pins {
 		pinctrl-single,pins = <
-			OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLUP | MUX_MODE4)	/* mcspi2_clk.gpio_178 */
-			OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLUP | MUX_MODE4)	/* mcspi2_cs0.gpio_181 */
-		>;
-	};
-
-	pwm_pins: pinmux_pwm_pins {
-		pinctrl-single,pins = <
-			OMAP3_CORE1_IOPAD(0x20B8, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE3)       /* gpmc_ncs5.gpt_10_pwm_evt */
-		>;
-	};
-
-	led_pins: pinmux_led_pins {
-		pinctrl-single,pins = <
-			OMAP3_CORE1_IOPAD(0x21d8, PIN_OUTPUT | MUX_MODE4)	/* gpio_179 */
-			OMAP3_CORE1_IOPAD(0x21da, PIN_OUTPUT | MUX_MODE4)	/* gpio_180 */
-		>;
-	};
-
-	mmc1_pins: pinmux_mmc1_pins {
-		pinctrl-single,pins = <
-			OMAP3_CORE1_IOPAD(0x2144, PIN_OUTPUT | MUX_MODE0)	/* sdmmc1_clk.sdmmc1_clk */
-			OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT | MUX_MODE0)	/* sdmmc1_cmd.sdmmc1_cmd */
-			OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT | MUX_MODE0)	/* sdmmc1_dat0.sdmmc1_dat0 */
-			OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT | MUX_MODE0)	/* sdmmc1_dat1.sdmmc1_dat1 */
-			OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT | MUX_MODE0)	/* sdmmc1_dat2.sdmmc1_dat2 */
-			OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT | MUX_MODE0)	/* sdmmc1_dat3.sdmmc1_dat3 */
-		>;
-	};
-
-	tsc2004_pins: pinmux_tsc2004_pins {
-		pinctrl-single,pins = <
-			OMAP3_CORE1_IOPAD(0x2186, PIN_INPUT | MUX_MODE4)	/* mcbsp4_dr.gpio_153 */
-		>;
-	};
-
-	backlight_pins: pinmux_backlight_pins {
-		pinctrl-single,pins = <
-			OMAP3_CORE1_IOPAD(0x2188, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4)       /* mcbsp4_dx.gpio_154 */
-		>;
-	};
-
-	isp_pins: pinmux_isp_pins {
-		pinctrl-single,pins = <
-			OMAP3_CORE1_IOPAD(0x210c, PIN_INPUT | MUX_MODE0)   /* cam_hs.cam_hs */
-			OMAP3_CORE1_IOPAD(0x210e, PIN_INPUT | MUX_MODE0)   /* cam_vs.cam_vs */
-			OMAP3_CORE1_IOPAD(0x2110, PIN_INPUT | MUX_MODE0)   /* cam_xclka.cam_xclka */
-			OMAP3_CORE1_IOPAD(0x2112, PIN_INPUT | MUX_MODE0)   /* cam_pclk.cam_pclk */
-
-			OMAP3_CORE1_IOPAD(0x2116, PIN_INPUT | MUX_MODE0)   /* cam_d0.cam_d0 */
-			OMAP3_CORE1_IOPAD(0x2118, PIN_INPUT | MUX_MODE0)   /* cam_d1.cam_d1 */
-			OMAP3_CORE1_IOPAD(0x211a, PIN_INPUT | MUX_MODE0)   /* cam_d2.cam_d2 */
-			OMAP3_CORE1_IOPAD(0x211c, PIN_INPUT | MUX_MODE0)   /* cam_d3.cam_d3 */
-			OMAP3_CORE1_IOPAD(0x211e, PIN_INPUT | MUX_MODE0)   /* cam_d4.cam_d4 */
-			OMAP3_CORE1_IOPAD(0x2120, PIN_INPUT | MUX_MODE0)   /* cam_d5.cam_d5 */
-			OMAP3_CORE1_IOPAD(0x2122, PIN_INPUT | MUX_MODE0)   /* cam_d6.cam_d6 */
-			OMAP3_CORE1_IOPAD(0x2124, PIN_INPUT | MUX_MODE0)   /* cam_d7.cam_d7 */
-		>;
-	};
-
-	panel_pwr_pins: pinmux_panel_pwr_pins {
-		pinctrl-single,pins = <
-			OMAP3_CORE1_IOPAD(0x218a, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4)       /* mcbsp4_fs.gpio_155 */
-		>;
-	};
-
-	dss_dpi_pins1: pinmux_dss_dpi_pins1 {
-		pinctrl-single,pins = <
-			OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_pclk.dss_pclk */
-			OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_hsync.dss_hsync */
-			OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_vsync.dss_vsync */
-			OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_acbias.dss_acbias */
-
-			OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data6.dss_data6 */
-			OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data7.dss_data7 */
-			OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data8.dss_data8 */
-			OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data9.dss_data9 */
-			OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data10.dss_data10 */
-			OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data11.dss_data11 */
-			OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data12.dss_data12 */
-			OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data13.dss_data13 */
-			OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data14.dss_data14 */
-			OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data15.dss_data15 */
-			OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data16.dss_data16 */
-			OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data17.dss_data17 */
-
-			OMAP3_CORE1_IOPAD(0x2100, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3)   /* dss_data18.dss_data0 */
-			OMAP3_CORE1_IOPAD(0x2102, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3)   /* dss_data19.dss_data1 */
-			OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3)   /* dss_data20.dss_data2 */
-			OMAP3_CORE1_IOPAD(0x2106, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3)   /* dss_data21.dss_data3 */
-			OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3)   /* dss_data22.dss_data4 */
-			OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3)   /* dss_data23.dss_data5 */
+			OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE3)	/* sdmmc2_dat4.sdmmc3_dat0 */
+			OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE3)	/* sdmmc2_dat5.sdmmc3_dat1 */
+			OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE3)	/* sdmmc2_dat6.sdmmc3_dat2 */
+			OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE3)	/* sdmmc2_dat6.sdmmc3_dat3 */
+			OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLUP | MUX_MODE4)	/* mcbsp4_clkx.gpio_152 */
+			OMAP3_CORE1_IOPAD(0x218e, PIN_OUTPUT | MUX_MODE4)	/* mcbsp1_fsr.gpio_157 */
 		>;
 	};
 };
 
-&omap3_pmx_wkup {
-	gpio_key_pins_wkup: pinmux_gpio_key_pins_wkup {
+&omap3_pmx_core2 {
+	mmc3_core2_pins: pinmux_mmc3_core2_pins {
 		pinctrl-single,pins = <
-			OMAP3_WKUP_IOPAD(0x2a0a, PIN_INPUT_PULLUP | MUX_MODE4)	/* sys_boot0.gpio_2 */
-			OMAP3_WKUP_IOPAD(0x2a14, PIN_INPUT_PULLUP | MUX_MODE4)	/* sys_boot5.gpio_7 */
-		>;
-	};
-
-	lan9221_pins: pinmux_lan9221_pins {
-		pinctrl-single,pins = <
-			OMAP3_WKUP_IOPAD(0x2a5a, PIN_INPUT | MUX_MODE4)		/* reserved.gpio_129 */
-		>;
-	};
-
-	mmc1_cd: pinmux_mmc1_cd {
-		pinctrl-single,pins = <
-			OMAP3_WKUP_IOPAD(0x2a54, PIN_INPUT_PULLUP | MUX_MODE4)	/* reserved.gpio_127 */
+			OMAP3630_CORE2_IOPAD(0x25d8, PIN_INPUT_PULLUP | MUX_MODE2)   /* etk_clk.sdmmc3_clk */
+			OMAP3630_CORE2_IOPAD(0x25da, PIN_INPUT_PULLUP | MUX_MODE2)   /* etk_ctl.sdmmc3_cmd */
 		>;
 	};
 };
-
-&i2c2 {
-	mt9p031@48 {
-		compatible = "aptina,mt9p031";
-		reg = <0x48>;
-		clocks = <&isp 0>;
-		vaa-supply = <&vaux4>;
-		vdd-supply = <&vaux4>;
-		vdd_io-supply = <&vaux4>;
-		port {
-			mt9p031_out: endpoint {
-				input-clock-frequency = <24000000>;
-				pixel-clock-frequency = <72000000>;
-				remote-endpoint = <&ccdc_ep>;
-			};
-		};
-	};
-};
-
-&i2c3 {
-	touchscreen: tsc2004@48 {
-		compatible = "ti,tsc2004";
-		reg = <0x48>;
-		vio-supply = <&vaux1>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&tsc2004_pins>;
-		interrupts-extended = <&gpio5 25 IRQ_TYPE_EDGE_RISING>; /* gpio 153 */
-
-		touchscreen-fuzz-x = <4>;
-		touchscreen-fuzz-y = <7>;
-		touchscreen-fuzz-pressure = <2>;
-		touchscreen-size-x = <4096>;
-		touchscreen-size-y = <4096>;
-		touchscreen-max-pressure = <2048>;
-
-		ti,x-plate-ohms = <280>;
-		ti,esd-recovery-timeout-ms = <8000>;
-	};
-};
-
-&mcspi1 {
-	at25@0 {
-		compatible = "atmel,at25";
-		reg = <0>;
-		spi-max-frequency = <5000000>;
-		spi-cpha;
-		spi-cpol;
-
-		pagesize = <64>;
-		size = <32768>;
-		address-width = <16>;
-	};
-};
-
-&isp {
-	pinctrl-names = "default";
-	pinctrl-0 = <&isp_pins>;
-	ports {
-		port@0 {
-			reg = <0>;
-			ccdc_ep: endpoint {
-				remote-endpoint = <&mt9p031_out>;
-				bus-width = <8>;
-				hsync-active = <1>;
-				vsync-active = <1>;
-				pclk-sample = <0>;
-			};
-		};
-	};
-};
-
-&uart1 {
-	interrupts-extended = <&intc 72 &omap3_pmx_core OMAP3_UART1_RX>;
-};
-
-/* Wired to the tps65950 on the SOM, only the USB connector is on the devkit */
-&usb_otg_hs {
-	pinctrl-names = "default";
-	pinctrl-0 = <&hsusb_otg_pins>;
-	interface-type = <0>;
-	usb-phy = <&usb2_phy>;
-	phys = <&usb2_phy>;
-	phy-names = "usb2-phy";
-	mode = <3>;
-	power = <50>;
-};

arch/arm/dts/logicpd-torpedo-baseboard.dtsi

@@ -0,0 +1,395 @@
+/*
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/ {
+	gpio_keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_key_pins &gpio_key_pins_wkup>;
+
+		sysboot2 {
+			label = "sysboot2";
+			gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;	/* gpio2 */
+			linux,code = <BTN_0>;
+			wakeup-source;
+		};
+
+		sysboot5 {
+			label = "sysboot5";
+			gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;	/* gpio7 */
+			linux,code = <BTN_1>;
+			wakeup-source;
+		};
+
+		gpio1 {
+			label = "gpio1";
+			gpios = <&gpio6 21 GPIO_ACTIVE_LOW>;	/* gpio181 */
+			linux,code = <BTN_2>;
+			wakeup-source;
+		};
+
+		gpio2 {
+			label = "gpio2";
+			gpios = <&gpio6 18 GPIO_ACTIVE_LOW>;	/* gpio178 */
+			linux,code = <BTN_3>;
+			wakeup-source;
+		};
+	};
+
+	sound {
+		compatible = "ti,omap-twl4030";
+		ti,model = "omap3logic";
+		ti,mcbsp = <&mcbsp2>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_pins>;
+
+		led1 {
+			label = "led1";
+			gpios = <&gpio6 20 GPIO_ACTIVE_HIGH>;	/* gpio180 */
+			linux,default-trigger = "cpu0";
+		};
+
+		led2 {
+			label = "led2";
+			gpios = <&gpio6 19 GPIO_ACTIVE_HIGH>;	/* gpio179 */
+			linux,default-trigger = "none";
+		};
+	};
+
+	pwm10: dmtimer-pwm {
+		compatible = "ti,omap-dmtimer-pwm";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pwm_pins>;
+		ti,timers = <&timer10>;
+		#pwm-cells = <3>;
+	};
+
+};
+
+&vaux1 {
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+};
+
+&vaux4 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+};
+
+&mcbsp2 {
+	status = "okay";
+};
+
+&charger {
+	ti,bb-uvolt = <3200000>;
+	ti,bb-uamp = <150>;
+};
+
+&gpmc {
+	ranges = <0 0 0x30000000 0x1000000	/* CS0: 16MB for NAND */
+		  1 0 0x2c000000 0x1000000>;	/* CS1: 16MB for LAN9221 */
+
+	ethernet@gpmc {
+		pinctrl-names = "default";
+		pinctrl-0 = <&lan9221_pins>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <1 IRQ_TYPE_LEVEL_LOW>;		/* gpio129 */
+		reg = <1 0 0xff>;
+	};
+};
+
+&vpll2 {
+	regulator-always-on;
+};
+
+&dss {
+	status = "ok";
+	vdds_dsi-supply = <&vpll2>;
+	vdda_video-supply = <&video_reg>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&dss_dpi_pins1>;
+	port {
+		dpi_out: endpoint {
+			remote-endpoint = <&lcd_in>;
+			data-lines = <16>;
+		};
+	};
+};
+
+/ {
+	aliases {
+		display0 = &lcd0;
+	};
+
+	video_reg: video_reg {
+		pinctrl-names = "default";
+		pinctrl-0 = <&panel_pwr_pins>;
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-supply";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio5 27 GPIO_ACTIVE_HIGH>;	/* gpio155, lcd INI */
+	};
+
+	lcd0: display {
+		compatible = "panel-dpi";
+		label = "15";
+		status = "okay";
+		/* default-on; */
+		pinctrl-names = "default";
+
+		port {
+			lcd_in: endpoint {
+				remote-endpoint = <&dpi_out>;
+			};
+		};
+
+		panel-timing {
+			clock-frequency = <9000000>;
+			hactive = <480>;
+			vactive = <272>;
+			hfront-porch = <3>;
+			hback-porch = <2>;
+			hsync-len = <42>;
+			vback-porch = <3>;
+			vfront-porch = <4>;
+			vsync-len = <11>;
+			hsync-active = <0>;
+			vsync-active = <0>;
+			de-active = <1>;
+			pixelclk-active = <1>;
+		};
+	};
+
+	bl: backlight {
+		compatible = "pwm-backlight";
+		pinctrl-names = "default";
+		pinctrl-0 = <&backlight_pins>;
+		pwms = <&pwm10 0 5000000 0>;
+		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+		default-brightness-level = <7>;
+		enable-gpios = <&gpio5 26 GPIO_ACTIVE_HIGH>; /* gpio_154 */
+	};
+};
+
+&mmc1 {
+	interrupts-extended = <&intc 83 &omap3_pmx_core 0x11a>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins &mmc1_cd>;
+	cd-gpios = <&gpio4 31 GPIO_ACTIVE_LOW>;		/* gpio127 */
+	vmmc-supply = <&vmmc1>;
+	bus-width = <4>;
+	cap-power-off-card;
+};
+
+&omap3_pmx_core {
+	gpio_key_pins: pinmux_gpio_key_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLUP | MUX_MODE4)	/* mcspi2_clk.gpio_178 */
+			OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLUP | MUX_MODE4)	/* mcspi2_cs0.gpio_181 */
+		>;
+	};
+
+	pwm_pins: pinmux_pwm_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x20B8, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE3)       /* gpmc_ncs5.gpt_10_pwm_evt */
+		>;
+	};
+
+	led_pins: pinmux_led_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21d8, PIN_OUTPUT | MUX_MODE4)	/* gpio_179 */
+			OMAP3_CORE1_IOPAD(0x21da, PIN_OUTPUT | MUX_MODE4)	/* gpio_180 */
+		>;
+	};
+
+	mmc1_pins: pinmux_mmc1_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2144, PIN_OUTPUT | MUX_MODE0)	/* sdmmc1_clk.sdmmc1_clk */
+			OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT | MUX_MODE0)	/* sdmmc1_cmd.sdmmc1_cmd */
+			OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT | MUX_MODE0)	/* sdmmc1_dat0.sdmmc1_dat0 */
+			OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT | MUX_MODE0)	/* sdmmc1_dat1.sdmmc1_dat1 */
+			OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT | MUX_MODE0)	/* sdmmc1_dat2.sdmmc1_dat2 */
+			OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT | MUX_MODE0)	/* sdmmc1_dat3.sdmmc1_dat3 */
+		>;
+	};
+
+	tsc2004_pins: pinmux_tsc2004_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2186, PIN_INPUT | MUX_MODE4)	/* mcbsp4_dr.gpio_153 */
+		>;
+	};
+
+	backlight_pins: pinmux_backlight_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2188, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4)       /* mcbsp4_dx.gpio_154 */
+		>;
+	};
+
+	isp_pins: pinmux_isp_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x210c, PIN_INPUT | MUX_MODE0)   /* cam_hs.cam_hs */
+			OMAP3_CORE1_IOPAD(0x210e, PIN_INPUT | MUX_MODE0)   /* cam_vs.cam_vs */
+			OMAP3_CORE1_IOPAD(0x2110, PIN_INPUT | MUX_MODE0)   /* cam_xclka.cam_xclka */
+			OMAP3_CORE1_IOPAD(0x2112, PIN_INPUT | MUX_MODE0)   /* cam_pclk.cam_pclk */
+
+			OMAP3_CORE1_IOPAD(0x2116, PIN_INPUT | MUX_MODE0)   /* cam_d0.cam_d0 */
+			OMAP3_CORE1_IOPAD(0x2118, PIN_INPUT | MUX_MODE0)   /* cam_d1.cam_d1 */
+			OMAP3_CORE1_IOPAD(0x211a, PIN_INPUT | MUX_MODE0)   /* cam_d2.cam_d2 */
+			OMAP3_CORE1_IOPAD(0x211c, PIN_INPUT | MUX_MODE0)   /* cam_d3.cam_d3 */
+			OMAP3_CORE1_IOPAD(0x211e, PIN_INPUT | MUX_MODE0)   /* cam_d4.cam_d4 */
+			OMAP3_CORE1_IOPAD(0x2120, PIN_INPUT | MUX_MODE0)   /* cam_d5.cam_d5 */
+			OMAP3_CORE1_IOPAD(0x2122, PIN_INPUT | MUX_MODE0)   /* cam_d6.cam_d6 */
+			OMAP3_CORE1_IOPAD(0x2124, PIN_INPUT | MUX_MODE0)   /* cam_d7.cam_d7 */
+		>;
+	};
+
+	panel_pwr_pins: pinmux_panel_pwr_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x218a, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4)       /* mcbsp4_fs.gpio_155 */
+		>;
+	};
+
+	dss_dpi_pins1: pinmux_dss_dpi_pins1 {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_pclk.dss_pclk */
+			OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_hsync.dss_hsync */
+			OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_vsync.dss_vsync */
+			OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_acbias.dss_acbias */
+
+			OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data6.dss_data6 */
+			OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data7.dss_data7 */
+			OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data8.dss_data8 */
+			OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data9.dss_data9 */
+			OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data10.dss_data10 */
+			OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data11.dss_data11 */
+			OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data12.dss_data12 */
+			OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data13.dss_data13 */
+			OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data14.dss_data14 */
+			OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data15.dss_data15 */
+			OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data16.dss_data16 */
+			OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0)   /* dss_data17.dss_data17 */
+
+			OMAP3_CORE1_IOPAD(0x2100, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3)   /* dss_data18.dss_data0 */
+			OMAP3_CORE1_IOPAD(0x2102, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3)   /* dss_data19.dss_data1 */
+			OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3)   /* dss_data20.dss_data2 */
+			OMAP3_CORE1_IOPAD(0x2106, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3)   /* dss_data21.dss_data3 */
+			OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3)   /* dss_data22.dss_data4 */
+			OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3)   /* dss_data23.dss_data5 */
+		>;
+	};
+};
+
+&omap3_pmx_wkup {
+	gpio_key_pins_wkup: pinmux_gpio_key_pins_wkup {
+		pinctrl-single,pins = <
+			OMAP3_WKUP_IOPAD(0x2a0a, PIN_INPUT_PULLUP | MUX_MODE4)	/* sys_boot0.gpio_2 */
+			OMAP3_WKUP_IOPAD(0x2a14, PIN_INPUT_PULLUP | MUX_MODE4)	/* sys_boot5.gpio_7 */
+		>;
+	};
+
+	lan9221_pins: pinmux_lan9221_pins {
+		pinctrl-single,pins = <
+			OMAP3_WKUP_IOPAD(0x2a5a, PIN_INPUT | MUX_MODE4)		/* reserved.gpio_129 */
+		>;
+	};
+
+	mmc1_cd: pinmux_mmc1_cd {
+		pinctrl-single,pins = <
+			OMAP3_WKUP_IOPAD(0x2a54, PIN_INPUT_PULLUP | MUX_MODE4)	/* reserved.gpio_127 */
+		>;
+	};
+};
+
+&i2c2 {
+	mt9p031@48 {
+		compatible = "aptina,mt9p031";
+		reg = <0x48>;
+		clocks = <&isp 0>;
+		vaa-supply = <&vaux4>;
+		vdd-supply = <&vaux4>;
+		vdd_io-supply = <&vaux4>;
+		port {
+			mt9p031_out: endpoint {
+				input-clock-frequency = <24000000>;
+				pixel-clock-frequency = <72000000>;
+				remote-endpoint = <&ccdc_ep>;
+			};
+		};
+	};
+};
+
+&i2c3 {
+	touchscreen: tsc2004@48 {
+		compatible = "ti,tsc2004";
+		reg = <0x48>;
+		vio-supply = <&vaux1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&tsc2004_pins>;
+		interrupts-extended = <&gpio5 25 IRQ_TYPE_EDGE_RISING>; /* gpio 153 */
+
+		touchscreen-fuzz-x = <4>;
+		touchscreen-fuzz-y = <7>;
+		touchscreen-fuzz-pressure = <2>;
+		touchscreen-size-x = <4096>;
+		touchscreen-size-y = <4096>;
+		touchscreen-max-pressure = <2048>;
+
+		ti,x-plate-ohms = <280>;
+		ti,esd-recovery-timeout-ms = <8000>;
+	};
+};
+
+&mcspi1 {
+	at25@0 {
+		compatible = "atmel,at25";
+		reg = <0>;
+		spi-max-frequency = <5000000>;
+		spi-cpha;
+		spi-cpol;
+
+		pagesize = <64>;
+		size = <32768>;
+		address-width = <16>;
+	};
+};
+
+&isp {
+	pinctrl-names = "default";
+	pinctrl-0 = <&isp_pins>;
+	ports {
+		port@0 {
+			reg = <0>;
+			ccdc_ep: endpoint {
+				remote-endpoint = <&mt9p031_out>;
+				bus-width = <8>;
+				hsync-active = <1>;
+				vsync-active = <1>;
+				pclk-sample = <0>;
+			};
+		};
+	};
+};
+
+&uart1 {
+	interrupts-extended = <&intc 72 &omap3_pmx_core OMAP3_UART1_RX>;
+};
+
+/* Wired to the tps65950 on the SOM, only the USB connector is on the devkit */
+&usb_otg_hs {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hsusb_otg_pins>;
+	interface-type = <0>;
+	usb-phy = <&usb2_phy>;
+	phys = <&usb2_phy>;
+	phy-names = "usb2-phy";
+	mode = <3>;
+	power = <50>;
+};

arch/arm/dts/logicpd-torpedo-som.dtsi

@@ -7,6 +7,10 @@
 #include <dt-bindings/input/input.h>
 
 / {
+	chosen {
+		stdout-path = &uart1;
+	};
+
 	cpus {
 		cpu@0 {
 			cpu0-supply = <&vcc>;
@@ -27,15 +31,11 @@
 		};
 	};
 
-	wl12xx_vmmc: wl12xx_vmmc {
-		compatible = "regulator-fixed";
-		regulator-name = "vwl1271";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		gpio = <&gpio5 29 0>;   /* gpio157 */
-		startup-delay-us = <70000>;
-		enable-active-high;
-		vin-supply = <&vmmc2>;
+	/* fixed 26MHz oscillator */
+	hfclk_26m: oscillator {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <26000000>;
 	};
 };
 
@@ -73,12 +73,17 @@
 };
 
 &i2c1 {
-	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <2600000>;
 
 	twl: twl@48 {
 		reg = <0x48>;
 		interrupts = <7>; /* SYS_NIRQ cascaded to intc */
 		interrupt-parent = <&intc>;
+		clocks = <&hfclk_26m>;
+		clock-names = "fck";
+
 		twl_audio: audio {
 			compatible = "ti,twl4030-audio";
 			codec {
@@ -88,56 +93,23 @@
 };
 
 &i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins>;
 	clock-frequency = <400000>;
 };
 
 &i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c3_pins>;
 	clock-frequency = <400000>;
 	at24@50 {
-		compatible = "at24,24c02";
+		compatible = "atmel,24c64";
 		readonly;
 		reg = <0x50>;
 	};
 };
 
-/*
- * Only found on the wireless SOM. For the SOM without wireless, the pins for
- * MMC3 can be routed with jumpers to the second MMC slot on the devkit and
- * gpio157 is not connected. So this should be OK to keep common for now,
- * probably device tree overlays is the way to go with the various SOM and
- * jumpering combinations for the long run.
- */
-&mmc3 {
-	interrupts-extended = <&intc 94 &omap3_pmx_core2 0x46>;
-	pinctrl-0 = <&mmc3_pins &mmc3_core2_pins>;
-	pinctrl-names = "default";
-	vmmc-supply = <&wl12xx_vmmc>;
-	non-removable;
-	bus-width = <4>;
-	cap-power-off-card;
-	#address-cells = <1>;
-	#size-cells = <0>;
-	wlcore: wlcore@2 {
-		compatible = "ti,wl1283";
-		reg = <2>;
-		interrupt-parent = <&gpio5>;
-		interrupts = <24 IRQ_TYPE_LEVEL_HIGH>; /* gpio 152 */
-		ref-clock-frequency = <26000000>;
-		tcxo-clock-frequency = <26000000>;
-	};
-};
-
 &omap3_pmx_core {
-	mmc3_pins: pinmux_mm3_pins {
-		pinctrl-single,pins = <
-			OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE3)	/* sdmmc2_dat4.sdmmc3_dat0 */
-			OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE3)	/* sdmmc2_dat5.sdmmc3_dat1 */
-			OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE3)	/* sdmmc2_dat6.sdmmc3_dat2 */
-			OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE3)	/* sdmmc2_dat6.sdmmc3_dat3 */
-			OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLUP | MUX_MODE4)	/* mcbsp4_clkx.gpio_152 */
-			OMAP3_CORE1_IOPAD(0x218e, PIN_OUTPUT | MUX_MODE4)	/* mcbsp1_fsr.gpio_157 */
-		>;
-	};
 	mcbsp2_pins: pinmux_mcbsp2_pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x213c, PIN_INPUT | MUX_MODE0)        /* mcbsp2_fsx */
@@ -180,6 +152,24 @@
 			OMAP3_CORE1_IOPAD(0x21b8, PIN_INPUT | MUX_MODE0)	/* hsusb0_data7.hsusb0_data7 */
 		>;
 	};
+	i2c1_pins: pinmux_i2c1_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21ba, PIN_INPUT | MUX_MODE0)        /* i2c1_scl.i2c1_scl */
+			OMAP3_CORE1_IOPAD(0x21bc, PIN_INPUT | MUX_MODE0)        /* i2c1_sda.i2c1_sda */
+		>;
+	};
+	i2c2_pins: pinmux_i2c2_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21be, PIN_INPUT | MUX_MODE0)	/* i2c2_scl */
+			OMAP3_CORE1_IOPAD(0x21c0, PIN_INPUT | MUX_MODE0)	/* i2c2_sda */
+		>;
+	};
+	i2c3_pins: pinmux_i2c3_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21c2, PIN_INPUT | MUX_MODE0)	/* i2c3_scl */
+			OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT | MUX_MODE0)	/* i2c3_sda */
+		>;
+	};
 };
 
 &uart2 {
@@ -193,15 +183,6 @@
 	pinctrl-0 = <&mcspi1_pins>;
 };
 
-&omap3_pmx_core2 {
-	mmc3_core2_pins: pinmux_mmc3_core2_pins {
-		pinctrl-single,pins = <
-			OMAP3630_CORE2_IOPAD(0x25d8, PIN_INPUT_PULLUP | MUX_MODE2)   /* etk_clk.sdmmc3_clk */
-			OMAP3630_CORE2_IOPAD(0x25da, PIN_INPUT_PULLUP | MUX_MODE2)   /* etk_ctl.sdmmc3_cmd */
-		>;
-	};
-};
-
 #include "twl4030.dtsi"
 #include "twl4030_omap3.dtsi"
 

arch/arm/dts/meson-gxbb-nanopi-k2.dts

@@ -0,0 +1,323 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2017 Andreas Färber
+ */
+
+/dts-v1/;
+
+#include "meson-gxbb.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	compatible = "friendlyarm,nanopi-k2", "amlogic,meson-gxbb";
+
+	aliases {
+		serial0 = &uart_AO;
+		ethernet0 = &ethmac;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		stat {
+			label = "nanopi-k2:blue:stat";
+			gpios = <&gpio_ao GPIOAO_13 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+			panic-indicator;
+		};
+	};
+
+	vdd_5v: regulator-vdd-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD_5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	vddio_ao18: regulator-vddio-ao18 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_AO18";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	vddio_ao3v3: regulator-vddio-ao3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_AO3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vddio_tf: regulator-vddio-tf {
+		compatible = "regulator-gpio";
+
+		regulator-name = "VDDIO_TF";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_HIGH>;
+		gpios-states = <0>;
+
+		states = <3300000 0>,
+		         <1800000 1>;
+
+		regulator-settling-time-up-us = <100>;
+		regulator-settling-time-down-us = <5000>;
+	};
+
+	wifi_32k: wifi-32k {
+		compatible = "pwm-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+		clocks = <&wifi_32k>;
+		clock-names = "ext_clock";
+	};
+
+	vcc1v8: regulator-vcc1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC1.8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	vcc3v3: regulator-vcc3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&ethmac {
+	status = "okay";
+	pinctrl-0 = <&eth_rgmii_pins>;
+	pinctrl-names = "default";
+
+	phy-handle = <&eth_phy0>;
+	phy-mode = "rgmii";
+
+	amlogic,tx-delay-ns = <2>;
+
+	snps,reset-gpio = <&gpio GPIOZ_14 0>;
+	snps,reset-delays-us = <0 10000 1000000>;
+	snps,reset-active-low;
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		eth_phy0: ethernet-phy@0 {
+			/* Realtek RTL8211F (0x001cc916) */
+			reg = <0>;
+			interrupt-parent = <&gpio_intc>;
+			/* MAC_INTR on GPIOZ_15 */
+			interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
+		};
+	};
+};
+
+&ir {
+	status = "okay";
+	pinctrl-0 = <&remote_input_ao_pins>;
+	pinctrl-names = "default";
+};
+
+&pinctrl_aobus {
+	gpio-line-names = "UART TX", "UART RX", "Power Control", "Power Key In",
+			  "VCCK En", "CON1 Header Pin31",
+			  "I2S Header Pin6", "IR In", "I2S Header Pin7",
+			  "I2S Header Pin3", "I2S Header Pin4",
+			  "I2S Header Pin5", "HDMI CEC", "SYS LED",
+			  /* GPIO_TEST_N */
+			  "";
+};
+
+&pinctrl_periphs {
+	gpio-line-names = /* Bank GPIOZ */
+			  "Eth MDIO", "Eth MDC", "Eth RGMII RX Clk",
+			  "Eth RX DV", "Eth RX D0", "Eth RX D1", "Eth RX D2",
+			  "Eth RX D3", "Eth RGMII TX Clk", "Eth TX En",
+			  "Eth TX D0", "Eth TX D1", "Eth TX D2", "Eth TX D3",
+			  "Eth PHY nRESET", "Eth PHY Intc",
+			  /* Bank GPIOH */
+			  "HDMI HPD", "HDMI DDC SDA", "HDMI DDC SCL",
+			  "CON1 Header Pin33",
+			  /* Bank BOOT */
+			  "eMMC D0", "eMMC D1", "eMMC D2", "eMMC D3", "eMMC D4",
+			  "eMMC D5", "eMMC D6", "eMMC D7", "eMMC Clk",
+			  "eMMC Reset", "eMMC CMD",
+			  "", "", "", "", "eMMC DS",
+			  "", "",
+			  /* Bank CARD */
+			  "SDCard D1", "SDCard D0", "SDCard CLK", "SDCard CMD",
+			  "SDCard D3", "SDCard D2", "SDCard Det",
+			  /* Bank GPIODV */
+			  "", "", "", "", "", "", "", "", "", "", "", "", "",
+			  "", "", "", "", "", "", "", "", "", "", "",
+			  "I2C A SDA", "I2C A SCK", "I2C B SDA", "I2C B SCK",
+			  "VDDEE Regulator", "VCCK Regulator",
+			  /* Bank GPIOY */
+			  "CON1 Header Pin7", "CON1 Header Pin11",
+			  "CON1 Header Pin13", "CON1 Header Pin15",
+			  "CON1 Header Pin18", "CON1 Header Pin19",
+			  "CON1 Header Pin22", "CON1 Header Pin21",
+			  "CON1 Header Pin24", "CON1 Header Pin23",
+			  "CON1 Header Pin26", "CON1 Header Pin29",
+			  "CON1 Header Pin32", "CON1 Header Pin8",
+			  "CON1 Header Pin10", "CON1 Header Pin16",
+			  "CON1 Header Pin12",
+			  /* Bank GPIOX */
+			  "WIFI SDIO D0", "WIFI SDIO D1", "WIFI SDIO D2",
+			  "WIFI SDIO D3", "WIFI SDIO CLK", "WIFI SDIO CMD",
+			  "WIFI Power Enable", "WIFI WAKE HOST",
+			  "Bluetooth PCM DOUT", "Bluetooth PCM DIN",
+			  "Bluetooth PCM SYNC", "Bluetooth PCM CLK",
+			  "Bluetooth UART TX", "Bluetooth UART RX",
+			  "Bluetooth UART CTS", "Bluetooth UART RTS",
+			  "", "", "", "WIFI 32K", "Bluetooth Enable",
+			  "Bluetooth WAKE HOST", "",
+			  /* Bank GPIOCLK */
+			  "", "CON1 Header Pin35", "", "";
+};
+
+&pwm_ef {
+	status = "okay";
+	pinctrl-0 = <&pwm_e_pins>;
+	pinctrl-names = "default";
+	clocks = <&clkc CLKID_FCLK_DIV4>;
+	clock-names = "clkin0";
+};
+
+&saradc {
+	status = "okay";
+	vref-supply = <&vddio_ao18>;
+};
+
+/* SDIO */
+&sd_emmc_a {
+	status = "okay";
+	pinctrl-0 = <&sdio_pins>, <&sdio_irq_pins>;
+	pinctrl-1 = <&sdio_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <200000000>;
+
+	non-removable;
+	disable-wp;
+
+	mmc-pwrseq = <&sdio_pwrseq>;
+
+	vmmc-supply = <&vddio_ao3v3>;
+	vqmmc-supply = <&vddio_ao18>;
+
+	brcmf: wifi@1 {
+		compatible = "brcm,bcm4329-fmac";
+		reg = <1>;
+	};
+};
+
+/* SD */
+&sd_emmc_b {
+	status = "okay";
+	pinctrl-0 = <&sdcard_pins>;
+	pinctrl-1 = <&sdcard_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	sd-uhs-sdr12;
+	sd-uhs-sdr25;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
+	max-frequency = <200000000>;
+	disable-wp;
+
+	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
+	cd-inverted;
+
+	vmmc-supply = <&vddio_ao3v3>;
+	vqmmc-supply = <&vddio_tf>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+	status = "disabled";
+	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+	pinctrl-1 = <&emmc_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <8>;
+	max-frequency = <200000000>;
+	non-removable;
+	disable-wp;
+	cap-mmc-highspeed;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+	vmmc-supply = <&vcc3v3>;
+	vqmmc-supply = <&vcc1v8>;
+};
+
+/* DBG_UART */
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+/* Bluetooth on AP6212 */
+&uart_A {
+	status = "disabled";
+	pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
+	pinctrl-names = "default";
+};
+
+/* 40-pin CON1 */
+&uart_C {
+	status = "disabled";
+	pinctrl-0 = <&uart_c_pins>;
+	pinctrl-names = "default";
+};
+
+&usb0_phy {
+	status = "okay";
+	phy-supply = <&vdd_5v>;
+};
+
+&usb1_phy {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+};
+
+&usb1 {
+	status = "okay";
+};

arch/arm/dts/meson-gxl-s905x-p212.dtsi

@@ -189,3 +189,10 @@
 &usb0 {
 	status = "okay";
 };
+
+&usb2_phy0 {
+        /*
+         * HDMI_5V is also used as supply for the USB VBUS.
+         */
+        phy-supply = <&hdmi_5v>;
+};

arch/arm/dts/omap3.dtsi

@@ -215,6 +215,7 @@
 			#dma-cells = <1>;
 			dma-channels = <32>;
 			dma-requests = <96>;
+			ti,hwmods = "dma";
 		};
 
 		gpio1: gpio@48310000 {
@@ -287,7 +288,6 @@
 		uart1: serial@4806a000 {
 			compatible = "ti,omap3-uart";
 			reg = <0x4806a000 0x2000>;
-			reg-shift = <2>;
 			interrupts-extended = <&intc 72>;
 			dmas = <&sdma 49 &sdma 50>;
 			dma-names = "tx", "rx";
@@ -298,7 +298,6 @@
 		uart2: serial@4806c000 {
 			compatible = "ti,omap3-uart";
 			reg = <0x4806c000 0x400>;
-			reg-shift = <2>;
 			interrupts-extended = <&intc 73>;
 			dmas = <&sdma 51 &sdma 52>;
 			dma-names = "tx", "rx";
@@ -309,7 +308,6 @@
 		uart3: serial@49020000 {
 			compatible = "ti,omap3-uart";
 			reg = <0x49020000 0x400>;
-			reg-shift = <2>;
 			interrupts-extended = <&intc 74>;
 			dmas = <&sdma 53 &sdma 54>;
 			dma-names = "tx", "rx";
@@ -559,6 +557,7 @@
 			dma-names = "tx", "rx";
 			clocks = <&mcbsp4_fck>;
 			clock-names = "fck";
+			#sound-dai-cells = <0>;
 			status = "disabled";
 		};
 
@@ -589,20 +588,6 @@
 			dma-names = "rx";
 		};
 
-		smartreflex_core: smartreflex@480cb000 {
-			compatible = "ti,omap3-smartreflex-core";
-			ti,hwmods = "smartreflex_core";
-			reg = <0x480cb000 0x400>;
-			interrupts = <19>;
-		};
-
-		smartreflex_mpu_iva: smartreflex@480c9000 {
-			compatible = "ti,omap3-smartreflex-iva";
-			ti,hwmods = "smartreflex_mpu_iva";
-			reg = <0x480c9000 0x400>;
-			interrupts = <18>;
-		};
-
 		timer1: timer@48318000 {
 			compatible = "ti,omap3430-timer";
 			reg = <0x48318000 0x400>;
@@ -717,6 +702,7 @@
 				compatible = "ti,ohci-omap3";
 				reg = <0x48064400 0x400>;
 				interrupts = <76>;
+				remote-wakeup-connected;
 			};
 
 			usbhsehci: ehci@48064800 {

arch/arm/dts/omap36xx.dtsi

@@ -8,6 +8,7 @@
  * kind, whether express or implied.
  */
 
+#include <dt-bindings/bus/ti-sysc.h>
 #include <dt-bindings/media/omap3-isp.h>
 
 #include "omap3.dtsi"
@@ -34,7 +35,6 @@
 		uart4: serial@49042000 {
 			compatible = "ti,omap3-uart";
 			reg = <0x49042000 0x400>;
-			reg-shift = <2>;
 			interrupts = <80>;
 			dmas = <&sdma 81 &sdma 82>;
 			dma-names = "tx", "rx";
@@ -94,6 +94,51 @@
 			compatible = "ti,omap36xx-bandgap";
 			#thermal-sensor-cells = <0>;
 		};
+
+		target-module@480cb000 {
+			compatible = "ti,sysc-omap3630-sr", "ti,sysc";
+			ti,hwmods = "smartreflex_core";
+			reg = <0x480cb038 0x4>;
+			reg-names = "sysc";
+			ti,sysc-mask = <SYSC_OMAP3_SR_ENAWAKEUP>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			clocks = <&sr2_fck>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x480cb000 0x001000>;
+
+			smartreflex_core: smartreflex@0 {
+				compatible = "ti,omap3-smartreflex-core";
+				reg = <0 0x400>;
+				interrupts = <19>;
+			};
+		};
+
+		target-module@480c9000 {
+			compatible = "ti,sysc-omap3630-sr", "ti,sysc";
+			ti,hwmods = "smartreflex_mpu_iva";
+			reg = <0x480c9038 0x4>;
+			reg-names = "sysc";
+			ti,sysc-mask = <SYSC_OMAP3_SR_ENAWAKEUP>;
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			clocks = <&sr1_fck>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x480c9000 0x001000>;
+
+
+			smartreflex_mpu_iva: smartreflex@480c9000 {
+				compatible = "ti,omap3-smartreflex-mpu-iva";
+				reg = <0 0x400>;
+				interrupts = <18>;
+			};
+		};
 	};
 
 	thermal_zones: thermal-zones {

arch/arm/dts/s900.dtsi

@@ -0,0 +1,53 @@
+// SPDX-License-Identifier: GPL-2.0+
+//
+// Device Tree Source for Actions Semi S900 SoC
+//
+// Copyright (C) 2015 Actions Semi Co., Ltd.
+// Copyright (C) 2018 Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
+
+/dts-v1/;
+#include <dt-bindings/clock/s900_cmu.h>
+
+/ {
+	compatible = "actions,s900";
+	#address-cells = <0x2>;
+	#size-cells = <0x2>;
+
+	losc: losc {
+		compatible = "fixed-clock";
+		clock-frequency = <32768>;
+		#clock-cells = <0>;
+	};
+
+	diff24M: diff24M {
+		compatible = "fixed-clock";
+		clock-frequency = <24000000>;
+		#clock-cells = <0>;
+	};
+
+	soc {
+		u-boot,dm-pre-reloc;
+		compatible = "simple-bus";
+		#address-cells = <0x2>;
+		#size-cells = <0x2>;
+		ranges;
+
+		uart5: serial@e012a000 {
+			u-boot,dm-pre-reloc;
+			compatible = "actions,s900-serial";
+			reg = <0x0 0xe012a000 0x0 0x1000>;
+			clocks = <&cmu CLOCK_UART5>;
+			status = "disabled";
+		};
+
+		cmu: clock-controller@e0160000 {
+			u-boot,dm-pre-reloc;
+			compatible = "actions,s900-cmu";
+			reg = <0x0 0xe0160000 0x0 0x1000>;
+			clocks = <&losc>, <&diff24M>;
+			clock-names = "losc", "diff24M";
+			#clock-cells = <1>;
+		};
+	};
+};
+

arch/arm/dts/socfpga_arria10.dtsi

@@ -637,8 +637,8 @@
 			#address-cells = <1>;
 			#size-cells = <1>;
 			compatible = "denali,denali-nand-dt", "altr,socfpga-denali-nand";
-			reg = <0xffb90000 0x72000>,
-			      <0xffb80000 0x10000>;
+			reg = <0xffb90000 0x20>,
+			      <0xffb80000 0x1000>;
 			reg-names = "nand_data", "denali_reg";
 			interrupts = <0 99 4>;
 			dma-mask = <0xffffffff>;

arch/arm/dts/socfpga_arria10_socdk.dtsi

@@ -34,6 +34,7 @@
 		name = "memory";
 		device_type = "memory";
 		reg = <0x0 0x40000000>; /* 1GB */
+		u-boot,dm-pre-reloc;
 	};
 
 	a10leds {

arch/arm/dts/socfpga_stratix10_socdk.dts

@@ -36,8 +36,8 @@
 
 	memory {
 		device_type = "memory";
-		/* We expect the bootloader to fill in the reg */
-		reg = <0 0 0 0>;
+		reg = <0 0 0 0x80000000>; /* 2GB */
+		u-boot,dm-pre-reloc;
 	};
 };
 

arch/arm/dts/stm32mp15-ddr.dtsi

@@ -13,12 +13,12 @@
 			reg = <0x5A003000 0x550
 			       0x5A004000 0x234>;
 
-			clocks = <&rcc_clk AXIDCG>,
-				 <&rcc_clk DDRC1>,
-				 <&rcc_clk DDRC2>,
-				 <&rcc_clk DDRPHYC>,
-				 <&rcc_clk DDRCAPB>,
-				 <&rcc_clk DDRPHYCAPB>;
+			clocks = <&rcc AXIDCG>,
+				 <&rcc DDRC1>,
+				 <&rcc DDRC2>,
+				 <&rcc DDRPHYC>,
+				 <&rcc DDRCAPB>,
+				 <&rcc DDRPHYCAPB>;
 
 			clock-names = "axidcg",
 				      "ddrc1",

arch/arm/dts/stm32mp157-pinctrl.dtsi

@@ -0,0 +1,359 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2017 - All Rights Reserved
+ * Author: Ludovic Barre <ludovic.barre@st.com> for STMicroelectronics.
+ */
+#include <dt-bindings/pinctrl/stm32-pinfunc.h>
+
+/ {
+	soc {
+		pinctrl: pin-controller@50002000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "st,stm32mp157-pinctrl";
+			ranges = <0 0x50002000 0xa400>;
+			interrupt-parent = <&exti>;
+			st,syscfg = <&exti 0x60 0xff>;
+			pins-are-numbered;
+
+			gpioa: gpio@50002000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x0 0x400>;
+				clocks = <&rcc GPIOA>;
+				st,bank-name = "GPIOA";
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 0 16>;
+			};
+
+			gpiob: gpio@50003000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x1000 0x400>;
+				clocks = <&rcc GPIOB>;
+				st,bank-name = "GPIOB";
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 16 16>;
+			};
+
+			gpioc: gpio@50004000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x2000 0x400>;
+				clocks = <&rcc GPIOC>;
+				st,bank-name = "GPIOC";
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 32 16>;
+			};
+
+			gpiod: gpio@50005000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x3000 0x400>;
+				clocks = <&rcc GPIOD>;
+				st,bank-name = "GPIOD";
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 48 16>;
+			};
+
+			gpioe: gpio@50006000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x4000 0x400>;
+				clocks = <&rcc GPIOE>;
+				st,bank-name = "GPIOE";
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 64 16>;
+			};
+
+			gpiof: gpio@50007000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x5000 0x400>;
+				clocks = <&rcc GPIOF>;
+				st,bank-name = "GPIOF";
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 80 16>;
+			};
+
+			gpiog: gpio@50008000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x6000 0x400>;
+				clocks = <&rcc GPIOG>;
+				st,bank-name = "GPIOG";
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 96 16>;
+			};
+
+			gpioh: gpio@50009000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x7000 0x400>;
+				clocks = <&rcc GPIOH>;
+				st,bank-name = "GPIOH";
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 112 16>;
+			};
+
+			gpioi: gpio@5000a000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x8000 0x400>;
+				clocks = <&rcc GPIOI>;
+				st,bank-name = "GPIOI";
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 128 16>;
+			};
+
+			gpioj: gpio@5000b000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x9000 0x400>;
+				clocks = <&rcc GPIOJ>;
+				st,bank-name = "GPIOJ";
+				ngpios = <16>;
+				gpio-ranges = <&pinctrl 0 144 16>;
+			};
+
+			gpiok: gpio@5000c000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0xa000 0x400>;
+				clocks = <&rcc GPIOK>;
+				st,bank-name = "GPIOK";
+				ngpios = <8>;
+				gpio-ranges = <&pinctrl 0 160 8>;
+			};
+
+			cec_pins_a: cec-0 {
+				pins {
+					pinmux = <STM32_PINMUX('A', 15, AF4)>;
+					bias-disable;
+					drive-open-drain;
+					slew-rate = <0>;
+				};
+			};
+
+			i2c1_pins_a: i2c1-0 {
+				pins {
+					pinmux = <STM32_PINMUX('D', 12, AF5)>, /* I2C1_SCL */
+						 <STM32_PINMUX('F', 15, AF5)>; /* I2C1_SDA */
+					bias-disable;
+					drive-open-drain;
+					slew-rate = <0>;
+				};
+			};
+
+			i2c2_pins_a: i2c2-0 {
+				pins {
+					pinmux = <STM32_PINMUX('H', 4, AF4)>, /* I2C2_SCL */
+						 <STM32_PINMUX('H', 5, AF4)>; /* I2C2_SDA */
+					bias-disable;
+					drive-open-drain;
+					slew-rate = <0>;
+				};
+			};
+
+			i2c5_pins_a: i2c5-0 {
+				pins {
+					pinmux = <STM32_PINMUX('A', 11, AF4)>, /* I2C5_SCL */
+						 <STM32_PINMUX('A', 12, AF4)>; /* I2C5_SDA */
+					bias-disable;
+					drive-open-drain;
+					slew-rate = <0>;
+				};
+			};
+
+			pwm2_pins_a: pwm2-0 {
+				pins {
+					pinmux = <STM32_PINMUX('A', 3, AF1)>; /* TIM2_CH4 */
+					bias-pull-down;
+					drive-push-pull;
+					slew-rate = <0>;
+				};
+			};
+
+			pwm8_pins_a: pwm8-0 {
+				pins {
+					pinmux = <STM32_PINMUX('I', 2, AF3)>; /* TIM8_CH4 */
+					bias-pull-down;
+					drive-push-pull;
+					slew-rate = <0>;
+				};
+			};
+
+			pwm12_pins_a: pwm12-0 {
+				pins {
+					pinmux = <STM32_PINMUX('H', 6, AF2)>; /* TIM12_CH1 */
+					bias-pull-down;
+					drive-push-pull;
+					slew-rate = <0>;
+				};
+			};
+
+			qspi_clk_pins_a: qspi-clk-0 {
+				pins {
+					pinmux = <STM32_PINMUX('F', 10, AF9)>; /* QSPI_CLK */
+					bias-disable;
+					drive-push-pull;
+					slew-rate = <3>;
+				};
+			};
+
+			qspi_bk1_pins_a: qspi-bk1-0 {
+				pins1 {
+					pinmux = <STM32_PINMUX('F', 8, AF10)>, /* QSPI_BK1_IO0 */
+						 <STM32_PINMUX('F', 9, AF10)>, /* QSPI_BK1_IO1 */
+						 <STM32_PINMUX('F', 7, AF9)>, /* QSPI_BK1_IO2 */
+						 <STM32_PINMUX('F', 6, AF9)>; /* QSPI_BK1_IO3 */
+					bias-disable;
+					drive-push-pull;
+					slew-rate = <3>;
+				};
+				pins2 {
+					pinmux = <STM32_PINMUX('B', 6, AF10)>; /* QSPI_BK1_NCS */
+					bias-pull-up;
+					drive-push-pull;
+					slew-rate = <3>;
+				};
+			};
+
+			qspi_bk2_pins_a: qspi-bk2-0 {
+				pins1 {
+					pinmux = <STM32_PINMUX('H', 2, AF9)>, /* QSPI_BK2_IO0 */
+						 <STM32_PINMUX('H', 3, AF9)>, /* QSPI_BK2_IO1 */
+						 <STM32_PINMUX('G', 10, AF11)>, /* QSPI_BK2_IO2 */
+						 <STM32_PINMUX('G', 7, AF11)>; /* QSPI_BK2_IO3 */
+					bias-disable;
+					drive-push-pull;
+					slew-rate = <3>;
+				};
+				pins2 {
+					pinmux = <STM32_PINMUX('C', 0, AF10)>; /* QSPI_BK2_NCS */
+					bias-pull-up;
+					drive-push-pull;
+					slew-rate = <3>;
+				};
+			};
+			sdmmc1_b4_pins_a: sdmmc1-b4@0 {
+				pins {
+					pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */
+						 <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */
+						 <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */
+						 <STM32_PINMUX('C', 11, AF12)>, /* SDMMC1_D3 */
+						 <STM32_PINMUX('C', 12, AF12)>, /* SDMMC1_CK */
+						 <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */
+					slew-rate = <3>;
+					drive-push-pull;
+					bias-disable;
+				};
+			};
+
+			sdmmc1_dir_pins_a: sdmmc1-dir@0 {
+				pins {
+					pinmux = <STM32_PINMUX('F', 2, AF11)>, /* SDMMC1_D0DIR */
+						 <STM32_PINMUX('C', 7, AF8)>, /* SDMMC1_D123DIR */
+						 <STM32_PINMUX('B', 9, AF11)>, /* SDMMC1_CDIR */
+						 <STM32_PINMUX('E', 4, AF8)>; /* SDMMC1_CKIN */
+					slew-rate = <3>;
+					drive-push-pull;
+					bias-pull-up;
+				};
+			};
+			sdmmc2_b4_pins_a: sdmmc2-b4@0 {
+				pins {
+					pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC2_D0 */
+						 <STM32_PINMUX('B', 15, AF9)>, /* SDMMC2_D1 */
+						 <STM32_PINMUX('B', 3, AF9)>, /* SDMMC2_D2 */
+						 <STM32_PINMUX('B', 4, AF9)>, /* SDMMC2_D3 */
+						 <STM32_PINMUX('E', 3, AF9)>, /* SDMMC2_CK */
+						 <STM32_PINMUX('G', 6, AF10)>; /* SDMMC2_CMD */
+					slew-rate = <3>;
+					drive-push-pull;
+					bias-pull-up;
+				};
+			};
+
+			sdmmc2_d47_pins_a: sdmmc2-d47@0 {
+				pins {
+					pinmux = <STM32_PINMUX('A', 8, AF9)>, /* SDMMC2_D4 */
+						 <STM32_PINMUX('A', 9, AF10)>, /* SDMMC2_D5 */
+						 <STM32_PINMUX('E', 5, AF9)>, /* SDMMC2_D6 */
+						 <STM32_PINMUX('D', 3, AF9)>; /* SDMMC2_D7 */
+					slew-rate = <3>;
+					drive-push-pull;
+					bias-pull-up;
+				};
+			};
+
+			uart4_pins_a: uart4-0 {
+				pins1 {
+					pinmux = <STM32_PINMUX('G', 11, AF6)>; /* UART4_TX */
+					bias-disable;
+					drive-push-pull;
+					slew-rate = <0>;
+				};
+				pins2 {
+					pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */
+					bias-disable;
+				};
+			};
+		};
+
+		pinctrl_z: pin-controller-z@54004000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "st,stm32mp157-z-pinctrl";
+			ranges = <0 0x54004000 0x400>;
+			pins-are-numbered;
+			interrupt-parent = <&exti>;
+			st,syscfg = <&exti 0x60 0xff>;
+
+			gpioz: gpio@54004000 {
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0 0x400>;
+				clocks = <&rcc GPIOZ>;
+				st,bank-name = "GPIOZ";
+				st,bank-ioport = <11>;
+				ngpios = <8>;
+				gpio-ranges = <&pinctrl_z 0 400 8>;
+			};
+
+			i2c4_pins_a: i2c4-0 {
+				pins {
+					pinmux = <STM32_PINMUX('Z', 4, AF6)>, /* I2C4_SCL */
+						 <STM32_PINMUX('Z', 5, AF6)>; /* I2C4_SDA */
+					bias-disable;
+					drive-open-drain;
+					slew-rate = <0>;
+				};
+			};
+		};
+	};
+};

arch/arm/dts/stm32mp157-u-boot.dtsi

@@ -29,13 +29,13 @@
 
 	soc {
 		u-boot,dm-pre-reloc;
-	};
 
-	stgen: stgen@5C008000 {
-		compatible = "st,stm32-stgen";
-		reg = <0x5C008000 0x1000>;
-		status = "okay";
-		u-boot,dm-pre-reloc;
+		stgen: stgen@5C008000 {
+			compatible = "st,stm32-stgen";
+			reg = <0x5C008000 0x1000>;
+			status = "okay";
+			u-boot,dm-pre-reloc;
+		};
 	};
 };
 
@@ -63,14 +63,6 @@
 	u-boot,dm-pre-reloc;
 };
 
-&rcc_clk {
-	u-boot,dm-pre-reloc;
-};
-
-&rcc_rst {
-	u-boot,dm-pre-reloc;
-};
-
 &rcc_reboot {
 	u-boot,dm-pre-reloc;
 };

arch/arm/dts/stm32mp157.dtsi

@@ -1,380 +0,0 @@
-/* SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) */
-/*
- * Copyright (C) STMicroelectronics 2018 - All Rights Reserved
- */
-
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/clock/stm32mp1-clks.h>
-#include <dt-bindings/reset-controller/stm32mp1-resets.h>
-
-/ {
-	#address-cells = <1>;
-	#size-cells = <1>;
-
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		cpu0: cpu@0 {
-			compatible = "arm,cortex-a7";
-			device_type = "cpu";
-			reg = <0>;
-		};
-
-		cpu1: cpu@1 {
-			compatible = "arm,cortex-a7";
-			device_type = "cpu";
-			reg = <1>;
-		};
-	};
-
-	aliases {
-		serial3 = &uart4;
-	};
-
-	intc: interrupt-controller@a0021000 {
-		compatible = "arm,cortex-a7-gic";
-		#interrupt-cells = <3>;
-		interrupt-controller;
-		reg = <0xa0021000 0x1000>,
-		      <0xa0022000 0x2000>;
-	};
-
-	clocks {
-		clk_hse: clk-hse {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <24000000>;
-		};
-
-		clk_hsi: clk-hsi {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <64000000>;
-		};
-
-		clk_lse: clk-lse {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <32768>;
-		};
-
-		clk_lsi: clk-lsi {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <32000>;
-		};
-
-		clk_csi: clk-csi {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <4000000>;
-		};
-	};
-
-	soc {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <1>;
-		interrupt-parent = <&intc>;
-		ranges;
-
-		uart4: serial@40010000 {
-			compatible = "st,stm32h7-uart";
-			reg = <0x40010000 0x400>;
-			clocks = <&rcc_clk UART4_K>;
-			status = "disabled";
-		};
-
-		sdmmc3: sdmmc@48004000 {
-			compatible = "st,stm32-sdmmc2";
-			reg = <0x48004000 0x400>, <0x48005000 0x400>;
-			reg-names = "sdmmc", "delay";
-			interrupts = <GIC_SPI 137 IRQ_TYPE_NONE>;
-			clocks = <&rcc_clk SDMMC3_K>;
-			resets = <&rcc_rst SDMMC3_R>;
-			st,idma = <1>;
-			cap-sd-highspeed;
-			cap-mmc-highspeed;
-			max-frequency = <120000000>;
-			status = "disabled";
-		};
-
-		rcc: rcc@50000000 {
-			compatible = "syscon", "simple-mfd";
-
-			reg = <0x50000000 0x1000>;
-
-			rcc_clk: rcc-clk@50000000 {
-				#clock-cells = <1>;
-				compatible = "st,stm32mp1-rcc-clk";
-			};
-
-			rcc_rst: rcc-reset@50000000 {
-				#reset-cells = <1>;
-				compatible = "st,stm32mp1-rcc-rst";
-			};
-
-			rcc_reboot: rcc-reboot@50000000 {
-				compatible = "syscon-reboot";
-				regmap = <&rcc>;
-				offset = <0x404>;
-				mask = <0x1>;
-			};
-		};
-
-		pwr: pwr@50001000 {
-			compatible = "st,stm32mp1-pwr", "st,stm32-pwr", "syscon", "simple-mfd";
-			reg = <0x50001000 0x400>;
-			system-power-controller;
-			interrupts = <GIC_SPI 149 IRQ_TYPE_NONE>;
-			st,sysrcc = <&rcc>;
-			clocks = <&rcc_clk PLL2_R>;
-			clock-names = "phyclk";
-
-			pwr-regulators@c {
-				compatible = "st,stm32mp1,pwr-reg";
-				st,tzcr = <&rcc 0x0 0x1>;
-
-				reg11: reg11 {
-					regulator-name = "reg11";
-					regulator-min-microvolt = <1100000>;
-					regulator-max-microvolt = <1100000>;
-				};
-
-				reg18: reg18 {
-					regulator-name = "reg18";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-				};
-
-				usb33: usb33 {
-					regulator-name = "usb33";
-					regulator-min-microvolt = <3300000>;
-					regulator-max-microvolt = <3300000>;
-				};
-			};
-		};
-
-		vrefbuf: vrefbuf@50025000 {
-			compatible = "st,stm32-vrefbuf";
-			reg = <0x50025000 0x8>;
-			regulator-min-microvolt = <1500000>;
-			regulator-max-microvolt = <2500000>;
-			clocks = <&rcc_clk VREF>;
-			status = "disabled";
-		};
-
-		pinctrl: pin-controller {
-			compatible = "st,stm32mp157-pinctrl";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0 0x50002000 0xa400>;
-			pins-are-numbered;
-
-			gpioa: gpio@50002000 {
-				gpio-controller;
-				#gpio-cells = <2>;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-				reg = <0x0 0x400>;
-				clocks = <&rcc_clk GPIOA>;
-				st,bank-name = "GPIOA";
-				ngpios = <16>;
-				gpio-ranges = <&pinctrl 0 0 16>;
-				status = "disabled";
-			};
-
-			gpiob: gpio@50003000 {
-				gpio-controller;
-				#gpio-cells = <2>;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-				reg = <0x1000 0x400>;
-				clocks = <&rcc_clk GPIOB>;
-				st,bank-name = "GPIOB";
-				ngpios = <16>;
-				gpio-ranges = <&pinctrl 0 16 16>;
-				status = "disabled";
-			};
-
-			gpioc: gpio@50004000 {
-				gpio-controller;
-				#gpio-cells = <2>;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-				reg = <0x2000 0x400>;
-				clocks = <&rcc_clk GPIOC>;
-				st,bank-name = "GPIOC";
-				ngpios = <16>;
-				gpio-ranges = <&pinctrl 0 32 16>;
-				status = "disabled";
-			};
-
-			gpiod: gpio@50005000 {
-				gpio-controller;
-				#gpio-cells = <2>;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-				reg = <0x3000 0x400>;
-				clocks = <&rcc_clk GPIOD>;
-				st,bank-name = "GPIOD";
-				ngpios = <16>;
-				gpio-ranges = <&pinctrl 0 48 16>;
-				status = "disabled";
-			};
-
-			gpioe: gpio@50006000 {
-				gpio-controller;
-				#gpio-cells = <2>;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-				reg = <0x4000 0x400>;
-				clocks = <&rcc_clk GPIOE>;
-				st,bank-name = "GPIOE";
-				ngpios = <16>;
-				gpio-ranges = <&pinctrl 0 64 16>;
-				status = "disabled";
-			};
-
-			gpiof: gpio@50007000 {
-				gpio-controller;
-				#gpio-cells = <2>;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-				reg = <0x5000 0x400>;
-				clocks = <&rcc_clk GPIOF>;
-				st,bank-name = "GPIOF";
-				ngpios = <16>;
-				gpio-ranges = <&pinctrl 0 80 16>;
-				status = "disabled";
-			};
-
-			gpiog: gpio@50008000 {
-				gpio-controller;
-				#gpio-cells = <2>;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-				reg = <0x6000 0x400>;
-				clocks = <&rcc_clk GPIOG>;
-				st,bank-name = "GPIOG";
-				ngpios = <16>;
-				gpio-ranges = <&pinctrl 0 96 16>;
-				status = "disabled";
-			};
-
-			gpioh: gpio@50009000 {
-				gpio-controller;
-				#gpio-cells = <2>;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-				reg = <0x7000 0x400>;
-				clocks = <&rcc_clk GPIOH>;
-				st,bank-name = "GPIOH";
-				ngpios = <16>;
-				gpio-ranges = <&pinctrl 0 112 16>;
-				status = "disabled";
-			};
-
-			gpioi: gpio@5000a000 {
-				gpio-controller;
-				#gpio-cells = <2>;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-				reg = <0x8000 0x400>;
-				clocks = <&rcc_clk GPIOI>;
-				st,bank-name = "GPIOI";
-				ngpios = <16>;
-				gpio-ranges = <&pinctrl 0 128 16>;
-				status = "disabled";
-			};
-
-			gpioj: gpio@5000b000 {
-				gpio-controller;
-				#gpio-cells = <2>;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-				reg = <0x9000 0x400>;
-				clocks = <&rcc_clk GPIOJ>;
-				st,bank-name = "GPIOJ";
-				ngpios = <16>;
-				gpio-ranges = <&pinctrl 0 144 16>;
-				status = "disabled";
-			};
-
-			gpiok: gpio@5000c000 {
-				gpio-controller;
-				#gpio-cells = <2>;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-				reg = <0xa000 0x400>;
-				clocks = <&rcc_clk GPIOK>;
-				st,bank-name = "GPIOK";
-				ngpios = <8>;
-				gpio-ranges = <&pinctrl 0 160 8>;
-				status = "disabled";
-			};
-		};
-
-		pinctrl_z: pin-controller-z {
-			compatible = "st,stm32mp157-z-pinctrl";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0 0x54004000 0x400>;
-			pins-are-numbered;
-
-			gpioz: gpio@54004000 {
-				gpio-controller;
-				#gpio-cells = <2>;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-				reg = <0 0x400>;
-				clocks = <&rcc_clk GPIOZ>;
-				st,bank-name = "GPIOZ";
-				st,bank-ioport = <11>;
-				ngpios = <8>;
-				gpio-ranges = <&pinctrl_z 0 400 8>;
-				status = "disabled";
-			};
-		};
-
-		sdmmc1: sdmmc@58005000 {
-			compatible = "st,stm32-sdmmc2";
-			reg = <0x58005000 0x1000>, <0x58006000 0x1000>;
-			reg-names = "sdmmc", "delay";
-			clocks = <&rcc_clk SDMMC1_K>;
-			resets = <&rcc_rst SDMMC1_R>;
-			st,idma = <1>;
-			cap-sd-highspeed;
-			cap-mmc-highspeed;
-			max-frequency = <120000000>;
-			status = "disabled";
-		};
-
-		sdmmc2: sdmmc@58007000 {
-			compatible = "st,stm32-sdmmc2";
-			reg = <0x58007000 0x1000>, <0x58008000 0x1000>;
-			reg-names = "sdmmc", "delay";
-			interrupts = <GIC_SPI 124 IRQ_TYPE_NONE>;
-			clocks = <&rcc_clk SDMMC2_K>;
-			resets = <&rcc_rst SDMMC2_R>;
-			st,idma = <1>;
-			cap-sd-highspeed;
-			cap-mmc-highspeed;
-			max-frequency = <120000000>;
-			status = "disabled";
-		};
-
-		i2c4: i2c@5c002000 {
-			compatible = "st,stm32f7-i2c";
-			reg = <0x5c002000 0x400>;
-			interrupt-names = "event", "error", "wakeup";
-			clocks = <&rcc_clk I2C4_K>;
-			resets = <&rcc_rst I2C4_R>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			wakeup-source;
-			status = "disabled";
-		};
-	};
-};

arch/arm/dts/stm32mp157c-ed1-u-boot.dtsi

@@ -45,7 +45,7 @@
 };
 
 /* CLOCK init */
-&rcc_clk {
+&rcc {
 	st,clksrc = <
 		CLK_MPU_PLL1P
 		CLK_AXI_PLL2P
@@ -73,18 +73,41 @@
 	>;
 
 	st,pkcs = <
-		CLK_CKPER_DISABLED
+		CLK_CKPER_HSE
+		CLK_FMC_ACLK
+		CLK_QSPI_ACLK
+		CLK_ETH_DISABLED
 		CLK_SDMMC12_PLL3R
+		CLK_DSI_DSIPLL
 		CLK_STGEN_HSE
-		CLK_I2C46_PCLK5
-		CLK_I2C12_PCLK1
+		CLK_USBPHY_HSE
+		CLK_SPI2S1_PLL3Q
+		CLK_SPI2S23_PLL3Q
+		CLK_SPI45_HSI
+		CLK_SPI6_HSI
+		CLK_I2C46_HSI
 		CLK_SDMMC3_PLL3R
-		CLK_I2C35_PCLK1
-		CLK_UART1_PCLK5
-		CLK_UART24_PCLK1
-		CLK_UART35_PCLK1
-		CLK_UART6_PCLK2
-		CLK_UART78_PCLK1
+		CLK_USBO_USBPHY
+		CLK_ADC_CKPER
+		CLK_CEC_LSE
+		CLK_I2C12_HSI
+		CLK_I2C35_HSI
+		CLK_UART1_HSI
+		CLK_UART24_HSI
+		CLK_UART35_HSI
+		CLK_UART6_HSI
+		CLK_UART78_HSI
+		CLK_SPDIF_PLL3Q
+		CLK_FDCAN_PLL4Q
+		CLK_SAI1_PLL3Q
+		CLK_SAI2_PLL3Q
+		CLK_SAI3_PLL3Q
+		CLK_SAI4_PLL3Q
+		CLK_RNG1_CSI
+		CLK_RNG2_CSI
+		CLK_LPTIM1_PCLK1
+		CLK_LPTIM23_PCLK3
+		CLK_LPTIM45_PCLK3
 	>;
 
 	/* VCO = 1300.0 MHz => P = 650 (CPU) */
@@ -101,9 +124,10 @@
 		u-boot,dm-pre-reloc;
 	};
 
-	/* VCO = 774.0 MHz => P = 194, Q = 37, R = 97 */
+	/* VCO = 786.4 MHz => P = 197, Q = 49, R = 98 */
 	pll3: st,pll@2 {
-		cfg = < 3 128 3 20 7 PQR(1,1,1) >;
+		cfg = < 2 97 3 15 7 PQR(1,1,1) >;
+		frac = < 0x9ba >;
 		u-boot,dm-pre-reloc;
 	};
 

arch/arm/dts/stm32mp157c-ed1.dts

@@ -1,27 +1,24 @@
-/* SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) */
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
 /*
  * Copyright (C) STMicroelectronics 2017 - All Rights Reserved
  * Author: Ludovic Barre <ludovic.barre@st.com> for STMicroelectronics.
  */
-
 /dts-v1/;
 
-#include "stm32mp157.dtsi"
+#include "stm32mp157c.dtsi"
+#include "stm32mp157-pinctrl.dtsi"
 #include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/stm32-pinfunc.h>
 #include <dt-bindings/mfd/st,stpmu1.h>
 
 / {
-	model = "STMicroelectronics STM32MP157C pmic eval daughter";
+	model = "STMicroelectronics STM32MP157C eval daughter";
 	compatible = "st,stm32mp157c-ed1", "st,stm32mp157";
 
 	chosen {
-		bootargs = "earlyprintk console=ttyS3,115200 root=/dev/ram";
 		stdout-path = "serial3:115200n8";
 	};
 
-	memory {
+	memory@c0000000 {
 		reg = <0xC0000000 0x40000000>;
 	};
 
@@ -39,129 +36,14 @@
 	};
 };
 
-&gpioa {
+&rng1 {
 	status = "okay";
 };
 
-&gpiob {
+&timers6 {
 	status = "okay";
-};
-
-&gpioc {
-	status = "okay";
-};
-
-&gpiod {
-	status = "okay";
-};
-
-&gpioe {
-	status = "okay";
-};
-
-&gpiof {
-	status = "okay";
-};
-
-&gpiog {
-	status = "okay";
-};
-
-&gpioh {
-	status = "okay";
-};
-
-&gpioi {
-	status = "okay";
-};
-
-&gpioj {
-	status = "okay";
-};
-
-&gpiok {
-	status = "okay";
-};
-
-&gpioz {
-	status = "okay";
-};
-
-&pinctrl {
-	uart4_pins_a: uart4@0 {
-		pins1 {
-			pinmux = <STM32_PINMUX('G', 11, AF6)>; /* UART4_TX */
-			bias-disable;
-			drive-push-pull;
-			slew-rate = <0>;
-		};
-		pins2 {
-			pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */
-			bias-disable;
-		};
-	};
-
-	sdmmc1_b4_pins_a: sdmmc1-b4@0 {
-		pins {
-			pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */
-				 <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */
-				 <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */
-				 <STM32_PINMUX('C', 11, AF12)>, /* SDMMC1_D3 */
-				 <STM32_PINMUX('C', 12, AF12)>, /* SDMMC1_CK */
-				 <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */
-			slew-rate = <3>;
-			drive-push-pull;
-			bias-disable;
-		};
-	};
-
-	sdmmc1_dir_pins_a: sdmmc1-dir@0 {
-		pins {
-			pinmux = <STM32_PINMUX('F', 2, AF11)>, /* SDMMC1_D0DIR */
-				 <STM32_PINMUX('C', 7, AF8)>, /* SDMMC1_D123DIR */
-				 <STM32_PINMUX('B', 9, AF11)>, /* SDMMC1_CDIR */
-				 <STM32_PINMUX('E', 4, AF8)>; /* SDMMC1_CKIN */
-			slew-rate = <3>;
-			drive-push-pull;
-			bias-pull-up;
-		};
-	};
-	sdmmc2_b4_pins_a: sdmmc2-b4@0 {
-		pins {
-			pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC2_D0 */
-				 <STM32_PINMUX('B', 15, AF9)>, /* SDMMC2_D1 */
-				 <STM32_PINMUX('B', 3, AF9)>, /* SDMMC2_D2 */
-				 <STM32_PINMUX('B', 4, AF9)>, /* SDMMC2_D3 */
-				 <STM32_PINMUX('E', 3, AF9)>, /* SDMMC2_CK */
-				 <STM32_PINMUX('G', 6, AF10)>; /* SDMMC2_CMD */
-			slew-rate = <3>;
-			drive-push-pull;
-			bias-pull-up;
-		};
-	};
-
-	sdmmc2_d47_pins_a: sdmmc2-d47@0 {
-		pins {
-			pinmux = <STM32_PINMUX('A', 8, AF9)>, /* SDMMC2_D4 */
-				 <STM32_PINMUX('A', 9, AF10)>, /* SDMMC2_D5 */
-				 <STM32_PINMUX('E', 5, AF9)>, /* SDMMC2_D6 */
-				 <STM32_PINMUX('D', 3, AF9)>; /* SDMMC2_D7 */
-			slew-rate = <3>;
-			drive-push-pull;
-			bias-pull-up;
-		};
-	};
-};
-
-&pinctrl_z {
-	i2c4_pins_a: i2c4@0 {
-		pins {
-			pinmux = <STM32_PINMUX('Z', 4, AF6)>, /* I2C4_SCL */
-				 <STM32_PINMUX('Z', 5, AF6)>; /* I2C4_SDA */
-			bias-disable;
-			drive-open-drain;
-			slew-rate = <0>;
-		};
+	timer@5 {
+		status = "okay";
 	};
 };
 
@@ -439,8 +321,11 @@
 	};
 };
 
+&pwr {
+	pwr-supply = <&vdd>;
+};
+
 &sdmmc1 {
-	pinctrl-names = "default";
 	pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
 	broken-cd;
 	st,dirpol;
@@ -458,7 +343,6 @@
 };
 
 &sdmmc2 {
-	pinctrl-names = "default";
 	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
 	non-removable;
 	no-sd;
@@ -466,6 +350,8 @@
 	st,dirpol;
 	st,negedge;
 	bus-width = <8>;
+	vmmc-supply = <&v3v3>;
+	vqmmc-supply = <&vdd>;
 	status = "okay";
 };
 
@@ -474,3 +360,15 @@
 	pinctrl-0 = <&uart4_pins_a>;
 	status = "okay";
 };
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+	vdda1v1-supply = <&reg11>;
+	vdda1v8-supply = <&reg18>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+	vdda1v1-supply = <&reg11>;
+	vdda1v8-supply = <&reg18>;
+};

arch/arm/dts/stm32mp157c-ev1-u-boot.dtsi

@@ -0,0 +1,62 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright : STMicroelectronics 2018
+ */
+
+#include "stm32mp157c-ed1-u-boot.dtsi"
+
+/ {
+	aliases {
+		spi0 = &qspi;
+		i2c1 = &i2c2;
+		i2c4 = &i2c5;
+	};
+};
+
+&flash0 {
+	compatible = "spi-flash";
+};
+
+&flash1 {
+	compatible = "spi-flash";
+};
+
+&v3v3 {
+	regulator-always-on;
+};
+
+/* SPL part **************************************/
+&qspi {
+	u-boot,dm-spl;
+};
+
+&qspi_clk_pins_a {
+	u-boot,dm-spl;
+	pins {
+		u-boot,dm-spl;
+	};
+};
+
+&qspi_bk1_pins_a {
+	u-boot,dm-spl;
+	pins1 {
+		u-boot,dm-spl;
+	};
+	pins2 {
+		u-boot,dm-spl;
+	};
+};
+
+&qspi_bk2_pins_a {
+	u-boot,dm-spl;
+	pins1 {
+		u-boot,dm-spl;
+	};
+	pins2 {
+		u-boot,dm-spl;
+	};
+};
+
+&flash0 {
+	u-boot,dm-spl;
+};

arch/arm/dts/stm32mp157c-ev1.dts

@@ -0,0 +1,101 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2017 - All Rights Reserved
+ * Author: Ludovic Barre <ludovic.barre@st.com> for STMicroelectronics.
+ */
+/dts-v1/;
+
+#include "stm32mp157c-ed1.dts"
+
+/ {
+	model = "STMicroelectronics STM32MP157C eval daughter on eval mother";
+	compatible = "st,stm32mp157c-ev1", "st,stm32mp157c-ed1", "st,stm32mp157";
+
+};
+
+&cec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&cec_pins_a>;
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+};
+
+&i2c5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c5_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+};
+
+&qspi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a &qspi_bk2_pins_a>;
+	reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	flash0: mx66l51235l@0 {
+		reg = <0>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <108000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+
+	flash1: mx66l51235l@1 {
+		reg = <1>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <108000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
+
+&timers2 {
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm2_pins_a>;
+		pinctrl-names = "default";
+		status = "okay";
+	};
+	timer@1 {
+		status = "okay";
+	};
+};
+
+&timers8 {
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm8_pins_a>;
+		pinctrl-names = "default";
+		status = "okay";
+	};
+	timer@7 {
+		status = "okay";
+	};
+};
+
+&timers12 {
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm12_pins_a>;
+		pinctrl-names = "default";
+		status = "okay";
+	};
+	timer@11 {
+		status = "okay";
+	};
+};
+
+&usbphyc {
+	status = "okay";
+};

arch/arm/dts/stm32mp157c.dtsi

@@ -0,0 +1,935 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2017 - All Rights Reserved
+ * Author: Ludovic Barre <ludovic.barre@st.com> for STMicroelectronics.
+ */
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/stm32mp1-clks.h>
+#include <dt-bindings/reset/stm32mp1-resets.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <0>;
+		};
+
+		cpu1: cpu@1 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <1>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci";
+		method = "smc";
+		cpu_off = <0x84000002>;
+		cpu_on = <0x84000003>;
+	};
+
+	aliases {
+		gpio0 = &gpioa;
+		gpio1 = &gpiob;
+		gpio2 = &gpioc;
+		gpio3 = &gpiod;
+		gpio4 = &gpioe;
+		gpio5 = &gpiof;
+		gpio6 = &gpiog;
+		gpio7 = &gpioh;
+		gpio8 = &gpioi;
+		gpio9 = &gpioj;
+		gpio10 = &gpiok;
+		serial0 = &usart1;
+		serial1 = &usart2;
+		serial2 = &usart3;
+		serial3 = &uart4;
+		serial4 = &uart5;
+		serial5 = &usart6;
+		serial6 = &uart7;
+		serial7 = &uart8;
+	};
+
+	intc: interrupt-controller@a0021000 {
+		compatible = "arm,cortex-a7-gic";
+		#interrupt-cells = <3>;
+		interrupt-controller;
+		reg = <0xa0021000 0x1000>,
+		      <0xa0022000 0x2000>;
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+		interrupt-parent = <&intc>;
+	};
+
+	clocks {
+		clk_hse: clk-hse {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <24000000>;
+		};
+
+		clk_hsi: clk-hsi {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <64000000>;
+		};
+
+		clk_lse: clk-lse {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <32768>;
+		};
+
+		clk_lsi: clk-lsi {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <32000>;
+		};
+
+		clk_csi: clk-csi {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <4000000>;
+		};
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		interrupt-parent = <&intc>;
+		ranges;
+
+		timers2: timer@40000000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40000000 0x400>;
+			clocks = <&rcc TIM2_K>;
+			clock-names = "int";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				status = "disabled";
+			};
+
+			timer@1 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <1>;
+				status = "disabled";
+			};
+		};
+
+		timers3: timer@40001000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40001000 0x400>;
+			clocks = <&rcc TIM3_K>;
+			clock-names = "int";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				status = "disabled";
+			};
+
+			timer@2 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <2>;
+				status = "disabled";
+			};
+		};
+
+		timers4: timer@40002000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40002000 0x400>;
+			clocks = <&rcc TIM4_K>;
+			clock-names = "int";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				status = "disabled";
+			};
+
+			timer@3 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <3>;
+				status = "disabled";
+			};
+		};
+
+		timers5: timer@40003000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40003000 0x400>;
+			clocks = <&rcc TIM5_K>;
+			clock-names = "int";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				status = "disabled";
+			};
+
+			timer@4 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <4>;
+				status = "disabled";
+			};
+		};
+
+		timers6: timer@40004000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40004000 0x400>;
+			clocks = <&rcc TIM6_K>;
+			clock-names = "int";
+			status = "disabled";
+
+			timer@5 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <5>;
+				status = "disabled";
+			};
+		};
+
+		timers7: timer@40005000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40005000 0x400>;
+			clocks = <&rcc TIM7_K>;
+			clock-names = "int";
+			status = "disabled";
+
+			timer@6 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <6>;
+				status = "disabled";
+			};
+		};
+
+		timers12: timer@40006000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40006000 0x400>;
+			clocks = <&rcc TIM12_K>;
+			clock-names = "int";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				status = "disabled";
+			};
+
+			timer@11 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <11>;
+				status = "disabled";
+			};
+		};
+
+		timers13: timer@40007000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40007000 0x400>;
+			clocks = <&rcc TIM13_K>;
+			clock-names = "int";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				status = "disabled";
+			};
+
+			timer@12 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <12>;
+				status = "disabled";
+			};
+		};
+
+		timers14: timer@40008000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x40008000 0x400>;
+			clocks = <&rcc TIM14_K>;
+			clock-names = "int";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				status = "disabled";
+			};
+
+			timer@13 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <13>;
+				status = "disabled";
+			};
+		};
+
+		lptimer1: timer@40009000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-lptimer";
+			reg = <0x40009000 0x400>;
+			clocks = <&rcc LPTIM1_K>;
+			clock-names = "mux";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm-lp";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			trigger@0 {
+				compatible = "st,stm32-lptimer-trigger";
+				reg = <0>;
+				status = "disabled";
+			};
+
+			counter {
+				compatible = "st,stm32-lptimer-counter";
+				status = "disabled";
+			};
+		};
+
+		usart2: serial@4000e000 {
+			compatible = "st,stm32h7-uart";
+			reg = <0x4000e000 0x400>;
+			interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc USART2_K>;
+			status = "disabled";
+		};
+
+		usart3: serial@4000f000 {
+			compatible = "st,stm32h7-uart";
+			reg = <0x4000f000 0x400>;
+			interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc USART3_K>;
+			status = "disabled";
+		};
+
+		uart4: serial@40010000 {
+			compatible = "st,stm32h7-uart";
+			reg = <0x40010000 0x400>;
+			interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc UART4_K>;
+			status = "disabled";
+		};
+
+		uart5: serial@40011000 {
+			compatible = "st,stm32h7-uart";
+			reg = <0x40011000 0x400>;
+			interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc UART5_K>;
+			status = "disabled";
+		};
+
+		i2c1: i2c@40012000 {
+			compatible = "st,stm32f7-i2c";
+			reg = <0x40012000 0x400>;
+			interrupt-names = "event", "error";
+			interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc I2C1_K>;
+			resets = <&rcc I2C1_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c2: i2c@40013000 {
+			compatible = "st,stm32f7-i2c";
+			reg = <0x40013000 0x400>;
+			interrupt-names = "event", "error";
+			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc I2C2_K>;
+			resets = <&rcc I2C2_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c3: i2c@40014000 {
+			compatible = "st,stm32f7-i2c";
+			reg = <0x40014000 0x400>;
+			interrupt-names = "event", "error";
+			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc I2C3_K>;
+			resets = <&rcc I2C3_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c5: i2c@40015000 {
+			compatible = "st,stm32f7-i2c";
+			reg = <0x40015000 0x400>;
+			interrupt-names = "event", "error";
+			interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc I2C5_K>;
+			resets = <&rcc I2C5_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		cec: cec@40016000 {
+			compatible = "st,stm32-cec";
+			reg = <0x40016000 0x400>;
+			interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc CEC_K>, <&clk_lse>;
+			clock-names = "cec", "hdmi-cec";
+			status = "disabled";
+		};
+
+		dac: dac@40017000 {
+			compatible = "st,stm32h7-dac-core";
+			reg = <0x40017000 0x400>;
+			clocks = <&rcc DAC12>;
+			clock-names = "pclk";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			dac1: dac@1 {
+				compatible = "st,stm32-dac";
+				#io-channels-cells = <1>;
+				reg = <1>;
+				status = "disabled";
+			};
+
+			dac2: dac@2 {
+				compatible = "st,stm32-dac";
+				#io-channels-cells = <1>;
+				reg = <2>;
+				status = "disabled";
+			};
+		};
+
+		uart7: serial@40018000 {
+			compatible = "st,stm32h7-uart";
+			reg = <0x40018000 0x400>;
+			interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc UART7_K>;
+			status = "disabled";
+		};
+
+		uart8: serial@40019000 {
+			compatible = "st,stm32h7-uart";
+			reg = <0x40019000 0x400>;
+			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc UART8_K>;
+			status = "disabled";
+		};
+
+		timers1: timer@44000000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x44000000 0x400>;
+			clocks = <&rcc TIM1_K>;
+			clock-names = "int";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				status = "disabled";
+			};
+
+			timer@0 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <0>;
+				status = "disabled";
+			};
+		};
+
+		timers8: timer@44001000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x44001000 0x400>;
+			clocks = <&rcc TIM8_K>;
+			clock-names = "int";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				status = "disabled";
+			};
+
+			timer@7 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <7>;
+				status = "disabled";
+			};
+		};
+
+		usart6: serial@44003000 {
+			compatible = "st,stm32h7-uart";
+			reg = <0x44003000 0x400>;
+			interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc USART6_K>;
+			status = "disabled";
+		};
+
+		timers15: timer@44006000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x44006000 0x400>;
+			clocks = <&rcc TIM15_K>;
+			clock-names = "int";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				status = "disabled";
+			};
+
+			timer@14 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <14>;
+				status = "disabled";
+			};
+		};
+
+		timers16: timer@44007000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x44007000 0x400>;
+			clocks = <&rcc TIM16_K>;
+			clock-names = "int";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				status = "disabled";
+			};
+			timer@15 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <15>;
+				status = "disabled";
+			};
+		};
+
+		timers17: timer@44008000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-timers";
+			reg = <0x44008000 0x400>;
+			clocks = <&rcc TIM17_K>;
+			clock-names = "int";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm";
+				status = "disabled";
+			};
+
+			timer@16 {
+				compatible = "st,stm32h7-timer-trigger";
+				reg = <16>;
+				status = "disabled";
+			};
+		};
+
+		dma1: dma@48000000 {
+			compatible = "st,stm32-dma";
+			reg = <0x48000000 0x400>;
+			interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc DMA1>;
+			#dma-cells = <4>;
+			st,mem2mem;
+			dma-requests = <8>;
+		};
+
+		dma2: dma@48001000 {
+			compatible = "st,stm32-dma";
+			reg = <0x48001000 0x400>;
+			interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc DMA2>;
+			#dma-cells = <4>;
+			st,mem2mem;
+			dma-requests = <8>;
+		};
+
+		dmamux1: dma-router@48002000 {
+			compatible = "st,stm32h7-dmamux";
+			reg = <0x48002000 0x1c>;
+			#dma-cells = <3>;
+			dma-requests = <128>;
+			dma-masters = <&dma1 &dma2>;
+			dma-channels = <16>;
+			clocks = <&rcc DMAMUX>;
+		};
+
+		sdmmc3: sdmmc@48004000 {
+			compatible = "st,stm32-sdmmc2";
+			reg = <0x48004000 0x400>, <0x48005000 0x400>;
+			reg-names = "sdmmc", "delay";
+			interrupts = <GIC_SPI 137 IRQ_TYPE_NONE>;
+			clocks = <&rcc SDMMC3_K>;
+			resets = <&rcc SDMMC3_R>;
+			st,idma = <1>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			max-frequency = <120000000>;
+			status = "disabled";
+		};
+
+		rcc: rcc@50000000 {
+			compatible = "st,stm32mp1-rcc", "syscon";
+			reg = <0x50000000 0x1000>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		rcc_reboot: rcc-reboot@50000000 {
+			compatible = "syscon-reboot";
+			regmap = <&rcc>;
+			offset = <0x404>;
+			mask = <0x1>;
+		};
+
+		pwr: pwr@50001000 {
+			compatible = "st,stm32mp1-pwr", "st,stm32-pwr", "syscon", "simple-mfd";
+			reg = <0x50001000 0x400>;
+			system-power-controller;
+			interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
+			st,sysrcc = <&rcc>;
+			clocks = <&rcc PLL2_R>;
+			clock-names = "phyclk";
+
+			pwr-regulators@c {
+				compatible = "st,stm32mp1,pwr-reg";
+				st,tzcr = <&rcc 0x0 0x1>;
+
+				reg11: reg11 {
+					regulator-name = "reg11";
+					regulator-min-microvolt = <1100000>;
+					regulator-max-microvolt = <1100000>;
+				};
+
+				reg18: reg18 {
+					regulator-name = "reg18";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+				};
+
+				usb33: usb33 {
+					regulator-name = "usb33";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+				};
+			};
+		};
+
+		exti: interrupt-controller@5000d000 {
+			compatible = "st,stm32mp1-exti", "syscon";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			reg = <0x5000d000 0x400>;
+		};
+
+		syscfg: system-config@50020000 {
+			compatible = "st,stm32-syscfg", "syscon";
+			reg = <0x50020000 0x400>;
+		};
+
+		lptimer2: timer@50021000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-lptimer";
+			reg = <0x50021000 0x400>;
+			clocks = <&rcc LPTIM2_K>;
+			clock-names = "mux";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm-lp";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			trigger@1 {
+				compatible = "st,stm32-lptimer-trigger";
+				reg = <1>;
+				status = "disabled";
+			};
+
+			counter {
+				compatible = "st,stm32-lptimer-counter";
+				status = "disabled";
+			};
+		};
+
+		lptimer3: timer@50022000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32-lptimer";
+			reg = <0x50022000 0x400>;
+			clocks = <&rcc LPTIM3_K>;
+			clock-names = "mux";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm-lp";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			trigger@2 {
+				compatible = "st,stm32-lptimer-trigger";
+				reg = <2>;
+				status = "disabled";
+			};
+		};
+
+		lptimer4: timer@50023000 {
+			compatible = "st,stm32-lptimer";
+			reg = <0x50023000 0x400>;
+			clocks = <&rcc LPTIM4_K>;
+			clock-names = "mux";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm-lp";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+		};
+
+		lptimer5: timer@50024000 {
+			compatible = "st,stm32-lptimer";
+			reg = <0x50024000 0x400>;
+			clocks = <&rcc LPTIM5_K>;
+			clock-names = "mux";
+			status = "disabled";
+
+			pwm {
+				compatible = "st,stm32-pwm-lp";
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+		};
+
+		vrefbuf: vrefbuf@50025000 {
+			compatible = "st,stm32-vrefbuf";
+			reg = <0x50025000 0x8>;
+			regulator-min-microvolt = <1500000>;
+			regulator-max-microvolt = <2500000>;
+			clocks = <&rcc VREF>;
+			status = "disabled";
+		};
+
+		cryp1: cryp@54001000 {
+			compatible = "st,stm32mp1-cryp";
+			reg = <0x54001000 0x400>;
+			interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc CRYP1>;
+			resets = <&rcc CRYP1_R>;
+			status = "disabled";
+		};
+
+		rng1: rng@54003000 {
+			compatible = "st,stm32-rng";
+			reg = <0x54003000 0x400>;
+			clocks = <&rcc RNG1_K>;
+			resets = <&rcc RNG1_R>;
+			status = "disabled";
+		};
+
+		mdma1: dma@58000000 {
+			compatible = "st,stm32h7-mdma";
+			reg = <0x58000000 0x1000>;
+			interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc MDMA>;
+			#dma-cells = <5>;
+			dma-channels = <32>;
+			dma-requests = <48>;
+		};
+
+		qspi: qspi@58003000 {
+			compatible = "st,stm32f469-qspi";
+			reg = <0x58003000 0x1000>, <0x70000000 0x10000000>;
+			reg-names = "qspi", "qspi_mm";
+			interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc QSPI_K>;
+			resets = <&rcc QSPI_R>;
+			status = "disabled";
+		};
+
+		sdmmc1: sdmmc@58005000 {
+			compatible = "st,stm32-sdmmc2";
+			reg = <0x58005000 0x1000>, <0x58006000 0x1000>;
+			reg-names = "sdmmc", "delay";
+			clocks = <&rcc SDMMC1_K>;
+			resets = <&rcc SDMMC1_R>;
+			st,idma = <1>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			max-frequency = <120000000>;
+			status = "disabled";
+		};
+
+		sdmmc2: sdmmc@58007000 {
+			compatible = "st,stm32-sdmmc2";
+			reg = <0x58007000 0x1000>, <0x58008000 0x1000>;
+			reg-names = "sdmmc", "delay";
+			interrupts = <GIC_SPI 124 IRQ_TYPE_NONE>;
+			clocks = <&rcc SDMMC2_K>;
+			resets = <&rcc SDMMC2_R>;
+			st,idma = <1>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			max-frequency = <120000000>;
+			status = "disabled";
+		};
+
+		crc1: crc@58009000 {
+			compatible = "st,stm32f7-crc";
+			reg = <0x58009000 0x400>;
+			clocks = <&rcc CRC1>;
+			status = "disabled";
+		};
+
+		usbh_ohci: usbh-ohci@5800c000 {
+			compatible = "generic-ohci";
+			reg = <0x5800c000 0x1000>;
+			clocks = <&rcc USBH>;
+			resets = <&rcc USBH_R>;
+			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		usbh_ehci: usbh-ehci@5800d000 {
+			compatible = "generic-ehci";
+			reg = <0x5800d000 0x1000>;
+			clocks = <&rcc USBH>;
+			resets = <&rcc USBH_R>;
+			interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+			companion = <&usbh_ohci>;
+			status = "disabled";
+		};
+
+		dsi: dsi@5a000000 {
+			compatible = "st,stm32-dsi";
+			reg = <0x5a000000 0x800>;
+			clocks = <&rcc DSI_K>, <&clk_hse>, <&rcc DSI_PX>;
+			clock-names = "pclk", "ref", "px_clk";
+			resets = <&rcc DSI_R>;
+			reset-names = "apb";
+			status = "disabled";
+		};
+
+		ltdc: display-controller@5a001000 {
+			compatible = "st,stm32-ltdc";
+			reg = <0x5a001000 0x400>;
+			interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc LTDC_PX>;
+			clock-names = "lcd";
+			resets = <&rcc LTDC_R>;
+			status = "disabled";
+		};
+
+		usbphyc: usbphyc@5a006000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "st,stm32mp1-usbphyc";
+			reg = <0x5a006000 0x1000>;
+			clocks = <&rcc USBPHY_K>;
+			resets = <&rcc USBPHY_R>;
+			status = "disabled";
+
+			usbphyc_port0: usb-phy@0 {
+				#phy-cells = <0>;
+				reg = <0>;
+			};
+
+			usbphyc_port1: usb-phy@1 {
+				#phy-cells = <1>;
+				reg = <1>;
+			};
+		};
+
+		usart1: serial@5c000000 {
+			compatible = "st,stm32h7-uart";
+			reg = <0x5c000000 0x400>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc USART1_K>;
+			status = "disabled";
+		};
+
+		i2c4: i2c@5c002000 {
+			compatible = "st,stm32f7-i2c";
+			reg = <0x5c002000 0x400>;
+			interrupt-names = "event", "error";
+			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc I2C4_K>;
+			resets = <&rcc I2C4_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c6: i2c@5c009000 {
+			compatible = "st,stm32f7-i2c";
+			reg = <0x5c009000 0x400>;
+			interrupt-names = "event", "error";
+			interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc I2C6_K>;
+			resets = <&rcc I2C6_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+	};
+};

arch/arm/dts/sun50i-a64-bananapi-m64.dts

@@ -1,6 +1,5 @@
 /*
  * Copyright (c) 2016 ARM Ltd.
- * Copyright (C) 2017 Jagan Teki <jteki@openedev.com>
  *
  * This file is dual-licensed: you can use it either under the terms
  * of the GPL or the X11 license, at your option. Note that this dual
@@ -52,6 +51,7 @@
 	compatible = "sinovoip,bananapi-m64", "allwinner,sun50i-a64";
 
 	aliases {
+		ethernet0 = &emac;
 		serial0 = &uart0;
 		serial1 = &uart1;
 	};
@@ -60,11 +60,29 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	reg_vcc3v3: vcc3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "vcc3v3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
+	leds {
+		compatible = "gpio-leds";
+
+		pwr-led {
+			label = "bananapi-m64:red:pwr";
+			gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */
+			default-state = "on";
+		};
+
+		green {
+			label = "bananapi-m64:green:user";
+			gpios = <&pio 4 14 GPIO_ACTIVE_HIGH>; /* PE14 */
+		};
+
+		blue {
+			label = "bananapi-m64:blue:user";
+			gpios = <&pio 4 15 GPIO_ACTIVE_HIGH>; /* PE15 */
+		};
+	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
 	};
 };
 
@@ -76,6 +94,15 @@
 	status = "okay";
 };
 
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii_pins>;
+	phy-mode = "rgmii";
+	phy-handle = <&ext_rgmii_phy>;
+	phy-supply = <&reg_dc1sw>;
+	status = "okay";
+};
+
 &i2c1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c1_pins>;
@@ -86,12 +113,18 @@
 	bias-pull-up;
 };
 
+&mdio {
+	ext_rgmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+
 &mmc0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins>;
-	vmmc-supply = <&reg_vcc3v3>;
-	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
-	cd-inverted;
+	vmmc-supply = <&reg_dcdc1>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
 	disable-wp;
 	bus-width = <4>;
 	status = "okay";
@@ -100,16 +133,26 @@
 &mmc1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc1_pins>;
-	vmmc-supply = <&reg_vcc3v3>;
+	vmmc-supply = <&reg_dldo2>;
+	vqmmc-supply = <&reg_dldo4>;
+	mmc-pwrseq = <&wifi_pwrseq>;
 	bus-width = <4>;
 	non-removable;
 	status = "okay";
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+		interrupt-parent = <&r_pio>;
+		interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>; /* PL3 */
+		interrupt-names = "host-wake";
+	};
 };
 
 &mmc2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc2_pins>;
-	vmmc-supply = <&reg_vcc3v3>;
+	vmmc-supply = <&reg_dcdc1>;
 	bus-width = <8>;
 	non-removable;
 	cap-mmc-hw-reset;
@@ -124,6 +167,135 @@
 	status = "okay";
 };
 
+&r_rsb {
+	status = "okay";
+
+	axp803: pmic@3a3 {
+		compatible = "x-powers,axp803";
+		reg = <0x3a3>;
+		interrupt-parent = <&r_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		x-powers,drive-vbus-en; /* set N_VBUSEN as output pin */
+	};
+};
+
+#include "axp803.dtsi"
+
+&reg_aldo1 {
+	/*
+	 * This regulator also drives the PE pingroup GPIOs,
+	 * which also controls two LEDs.
+	 */
+	regulator-always-on;
+	regulator-min-microvolt = <2800000>;
+	regulator-max-microvolt = <2800000>;
+	regulator-name = "afvcc-csi";
+};
+
+&reg_aldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-pl";
+};
+
+&reg_aldo3 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "vcc-pll-avcc";
+};
+
+&reg_dc1sw {
+	/*
+	 * This regulator also indirectly drives the PD pingroup GPIOs,
+	 * which also controls the power LED.
+	 */
+	regulator-always-on;
+	regulator-name = "vcc-phy";
+};
+
+&reg_dcdc1 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-3v3";
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1040000>;
+	regulator-max-microvolt = <1300000>;
+	regulator-name = "vdd-cpux";
+};
+
+/* DCDC3 is polyphased with DCDC2 */
+
+&reg_dcdc5 {
+	regulator-always-on;
+	regulator-min-microvolt = <1500000>;
+	regulator-max-microvolt = <1500000>;
+	regulator-name = "vcc-dram";
+};
+
+&reg_dcdc6 {
+	regulator-always-on;
+	regulator-min-microvolt = <1100000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-sys";
+};
+
+&reg_dldo1 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-hdmi-dsi";
+};
+
+&reg_dldo2 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi";
+};
+
+&reg_dldo4 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi-io";
+};
+
+&reg_drivevbus {
+	regulator-name = "usb0-vbus";
+	status = "okay";
+};
+
+&reg_eldo1 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "cpvdd";
+};
+
+&reg_fldo1 {
+	regulator-min-microvolt = <1200000>;
+	regulator-max-microvolt = <1200000>;
+	regulator-name = "vcc-1v2-hsic";
+};
+
+/*
+ * The A64 chip cannot work without this regulator off, although
+ * it seems to be only driving the AR100 core.
+ * Maybe we don't still know well about CPUs domain.
+ */
+&reg_fldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1100000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-cpus";
+};
+
+&reg_rtc_ldo {
+	regulator-name = "vcc-rtc";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pins_a>;
@@ -143,5 +315,6 @@
 
 &usbphy {
 	usb0_id_det-gpios = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */
+	usb0_vbus-supply = <&reg_drivevbus>;
 	status = "okay";
 };

arch/arm/dts/sun50i-a64-nanopi-a64.dts

@@ -57,13 +57,6 @@
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
-
-	reg_vcc3v3: vcc3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "vcc3v3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-	};
 };
 
 &ehci0 {
@@ -88,9 +81,8 @@
 &mmc0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins>;
-	vmmc-supply = <&reg_vcc3v3>;
-	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
-	cd-inverted;
+	vmmc-supply = <&reg_dcdc1>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
 	disable-wp;
 	bus-width = <4>;
 	status = "okay";
@@ -104,6 +96,105 @@
 	status = "okay";
 };
 
+&r_rsb {
+	status = "okay";
+
+	axp803: pmic@3a3 {
+		compatible = "x-powers,axp803";
+		reg = <0x3a3>;
+		interrupt-parent = <&r_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+#include "axp803.dtsi"
+
+&reg_aldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-pl";
+};
+
+&reg_aldo3 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "vcc-pll-avcc";
+};
+
+&reg_dcdc1 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "vcc-3v";
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1040000>;
+	regulator-max-microvolt = <1300000>;
+	regulator-name = "vdd-cpux";
+};
+
+/* DCDC3 is polyphased with DCDC2 */
+
+&reg_dcdc5 {
+	regulator-always-on;
+	regulator-min-microvolt = <1500000>;
+	regulator-max-microvolt = <1500000>;
+	regulator-name = "vcc-dram";
+};
+
+&reg_dcdc6 {
+	regulator-always-on;
+	regulator-min-microvolt = <1100000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-sys";
+};
+
+&reg_dldo1 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-hdmi-dsi";
+};
+
+&reg_dldo4 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "vcc-pg-wifi-io";
+};
+
+&reg_eldo1 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "cpvdd";
+};
+
+&reg_fldo1 {
+	regulator-min-microvolt = <1200000>;
+	regulator-max-microvolt = <1200000>;
+	regulator-name = "vcc-1v2-hsic";
+};
+
+/*
+ * The A64 chip cannot work without this regulator off, although
+ * it seems to be only driving the AR100 core.
+ * Maybe we don't still know well about CPUs domain.
+ */
+&reg_fldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1100000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-cpus";
+};
+
+&reg_rtc_ldo {
+	regulator-name = "vcc-rtc";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pins_a>;

arch/arm/dts/sun50i-a64-olinuxino.dts

@@ -58,25 +58,162 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	reg_vcc3v3: vcc3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "vcc3v3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
 	};
 };
 
 &mmc0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins>;
-	vmmc-supply = <&reg_vcc3v3>;
-	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
-	cd-inverted;
+	vmmc-supply = <&reg_dcdc1>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
 	disable-wp;
 	bus-width = <4>;
 	status = "okay";
 };
 
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	vmmc-supply = <&reg_aldo2>;
+	vqmmc-supply = <&reg_dldo4>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	rtl8723bs: wifi@1 {
+		reg = <1>;
+		interrupt-parent = <&r_pio>;
+		interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>; /* PL3 */
+		interrupt-names = "host-wake";
+	};
+};
+
+&r_rsb {
+	status = "okay";
+
+	axp803: pmic@3a3 {
+		compatible = "x-powers,axp803";
+		reg = <0x3a3>;
+		interrupt-parent = <&r_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+#include "axp803.dtsi"
+
+&reg_aldo1 {
+	regulator-always-on;
+	regulator-min-microvolt = <2800000>;
+	regulator-max-microvolt = <2800000>;
+	regulator-name = "vcc-pe";
+};
+
+&reg_aldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-pl";
+};
+
+&reg_aldo3 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "vcc-pll-avcc";
+};
+
+&reg_dcdc1 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-3v3";
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1040000>;
+	regulator-max-microvolt = <1300000>;
+	regulator-name = "vdd-cpux";
+};
+
+/* DCDC3 is polyphased with DCDC2 */
+
+&reg_dcdc5 {
+	regulator-always-on;
+	regulator-min-microvolt = <1500000>;
+	regulator-max-microvolt = <1500000>;
+	regulator-name = "vcc-ddr3";
+};
+
+&reg_dcdc6 {
+	regulator-always-on;
+	regulator-min-microvolt = <1100000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-sys";
+};
+
+&reg_dldo1 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-hdmi";
+};
+
+&reg_dldo2 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-mipi";
+};
+
+&reg_dldo3 {
+	regulator-min-microvolt = <2800000>;
+	regulator-max-microvolt = <2800000>;
+	regulator-name = "vcc-avdd-csi";
+};
+
+&reg_dldo4 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi-io";
+};
+
+&reg_eldo1 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "cpvdd";
+};
+
+&reg_eldo2 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "vcc-dvdd-csi";
+};
+
+&reg_fldo1 {
+	regulator-min-microvolt = <1200000>;
+	regulator-max-microvolt = <1200000>;
+	regulator-name = "vcc-1v2-hsic";
+};
+
+/*
+ * The A64 chip cannot work without this regulator off, although
+ * it seems to be only driving the AR100 core.
+ * Maybe we don't still know well about CPUs domain.
+ */
+&reg_fldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1100000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-cpus";
+};
+
+&reg_rtc_ldo {
+	regulator-name = "vcc-rtc";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pins_a>;

arch/arm/dts/sun50i-a64-orangepi-win.dts

@@ -57,30 +57,138 @@
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
-
-	reg_vcc3v3: vcc3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "vcc3v3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-	};
 };
 
 &ehci1 {
-       status = "okay";
+	status = "okay";
 };
 
 &mmc0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins>;
-	vmmc-supply = <&reg_vcc3v3>;
-	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
-	cd-inverted;
+	vmmc-supply = <&reg_dcdc1>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
 
 &ohci1 {
-       status = "okay";
+	status = "okay";
+};
+
+&r_rsb {
+	status = "okay";
+
+	axp803: pmic@3a3 {
+		compatible = "x-powers,axp803";
+		reg = <0x3a3>;
+		interrupt-parent = <&r_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+#include "axp803.dtsi"
+
+&reg_aldo1 {
+	regulator-always-on;
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "afvcc-csi";
+};
+
+&reg_aldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-pl";
+};
+
+&reg_aldo3 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "vcc-pll-avcc";
+};
+
+&reg_dcdc1 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-3v3";
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1040000>;
+	regulator-max-microvolt = <1300000>;
+	regulator-name = "vdd-cpux";
+};
+
+/* DCDC3 is polyphased with DCDC2 */
+
+&reg_dcdc5 {
+	regulator-always-on;
+	regulator-min-microvolt = <1500000>;
+	regulator-max-microvolt = <1500000>;
+	regulator-name = "vcc-dram";
+};
+
+&reg_dcdc6 {
+	regulator-always-on;
+	regulator-min-microvolt = <1100000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-sys";
+};
+
+&reg_dldo1 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-hdmi-dsi";
+};
+
+&reg_dldo2 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi";
+};
+
+&reg_dldo3 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "avdd-csi";
+};
+
+&reg_dldo4 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi-io";
+};
+
+&reg_eldo1 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "cpvdd";
+};
+
+&reg_fldo1 {
+	regulator-min-microvolt = <1200000>;
+	regulator-max-microvolt = <1200000>;
+	regulator-name = "vcc-1v2-hsic";
+};
+
+/*
+ * The A64 chip cannot work without this regulator off, although
+ * it seems to be only driving the AR100 core.
+ * Maybe we don't still know well about CPUs domain.
+ */
+&reg_fldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1100000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-cpus";
+};
+
+&reg_rtc_ldo {
+	regulator-name = "vcc-rtc";
 };
 
 &uart0 {
@@ -90,5 +198,6 @@
 };
 
 &usbphy {
-       status = "okay";
+	status = "okay";
 };
+

arch/arm/dts/sun50i-a64-pine64-plus-u-boot.dtsi

@@ -1,59 +0,0 @@
-/ {
-	aliases {
-		ethernet0 = &emac;
-	};
-
-	soc {
-		syscon: syscon@1c00000 {
-			compatible = "allwinner,sun50i-a64-system-controller",
-				     "syscon";
-			reg = <0x01c00000 0x1000>;
-		};
-
-		emac: ethernet@1c30000 {
-			compatible = "allwinner,sun50i-a64-emac";
-			syscon = <&syscon>;
-			reg = <0x01c30000 0x10000>;
-			interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "macirq";
-			resets = <&ccu RST_BUS_EMAC>;
-			reset-names = "stmmaceth";
-			clocks = <&ccu CLK_BUS_EMAC>;
-			clock-names = "stmmaceth";
-			#address-cells = <1>;
-			#size-cells = <0>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&rgmii_pins>;
-			phy-mode = "rgmii";
-			phy-handle = <&ext_rgmii_phy>;
-			status = "okay";
-
-			mdio: mdio {
-				compatible = "snps,dwmac-mdio";
-				#address-cells = <1>;
-				#size-cells = <0>;
-				ext_rgmii_phy: ethernet-phy@1 {
-					compatible = "ethernet-phy-ieee802.3-c22";
-					reg = <1>;
-				};
-			};
-		};
-	};
-};
-
-&pio {
-	rmii_pins: rmii_pins {
-		pins = "PD10", "PD11", "PD13", "PD14", "PD17",
-		       "PD18", "PD19", "PD20", "PD22", "PD23";
-		function = "emac";
-		drive-strength = <40>;
-	};
-
-	rgmii_pins: rgmii_pins {
-		pins = "PD8", "PD9", "PD10", "PD11", "PD12",
-		       "PD13", "PD15", "PD16", "PD17", "PD18",
-		       "PD19", "PD20", "PD21", "PD22", "PD23";
-		function = "emac";
-		drive-strength = <40>;
-	};
-};

arch/arm/dts/sun50i-a64-pine64-plus.dts

@@ -46,5 +46,20 @@
 	model = "Pine64+";
 	compatible = "pine64,pine64-plus", "allwinner,sun50i-a64";
 
-	/* TODO: Camera, Ethernet PHY, touchscreen, etc. */
+	/* TODO: Camera, touchscreen, etc. */
+};
+
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii_pins>;
+	phy-mode = "rgmii";
+	phy-handle = <&ext_rgmii_phy>;
+	status = "okay";
+};
+
+&mdio {
+	ext_rgmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
 };

arch/arm/dts/sun50i-a64-pine64.dts

@@ -51,25 +51,37 @@
 	compatible = "pine64,pine64", "allwinner,sun50i-a64";
 
 	aliases {
+		ethernet0 = &emac;
 		serial0 = &uart0;
+		serial1 = &uart1;
+		serial2 = &uart2;
+		serial3 = &uart3;
+		serial4 = &uart4;
 	};
 
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
+};
 
-	reg_vcc3v3: vcc3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "vcc3v3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-	};
+&ehci0 {
+	status = "okay";
 };
 
 &ehci1 {
 	status = "okay";
 };
 
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&rmii_pins>;
+	phy-mode = "rmii";
+	phy-handle = <&ext_rmii_phy1>;
+	phy-supply = <&reg_dc1sw>;
+	status = "okay";
+
+};
+
 &i2c1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c1_pins>;
@@ -80,27 +92,183 @@
 	bias-pull-up;
 };
 
+&mdio {
+	ext_rmii_phy1: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+
 &mmc0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins>;
-	vmmc-supply = <&reg_vcc3v3>;
-	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
-	cd-inverted;
+	vmmc-supply = <&reg_dcdc1>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
 	disable-wp;
 	bus-width = <4>;
 	status = "okay";
 };
 
+&ohci0 {
+	status = "okay";
+};
+
 &ohci1 {
 	status = "okay";
 };
 
+&r_rsb {
+	status = "okay";
+
+	axp803: pmic@3a3 {
+		compatible = "x-powers,axp803";
+		reg = <0x3a3>;
+		interrupt-parent = <&r_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+#include "axp803.dtsi"
+
+&reg_aldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-pl";
+};
+
+&reg_aldo3 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "vcc-pll-avcc";
+};
+
+&reg_dc1sw {
+	regulator-name = "vcc-phy";
+};
+
+&reg_dcdc1 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-3v3";
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1040000>;
+	regulator-max-microvolt = <1300000>;
+	regulator-name = "vdd-cpux";
+};
+
+/* DCDC3 is polyphased with DCDC2 */
+
+/*
+ * The DRAM chips used by Pine64 boards are DDR3L-compatible, so they can
+ * work at 1.35V with less power consumption.
+ * As AXP803 DCDC5 cannot reach 1.35V accurately, use 1.36V instead.
+ */
+&reg_dcdc5 {
+	regulator-always-on;
+	regulator-min-microvolt = <1360000>;
+	regulator-max-microvolt = <1360000>;
+	regulator-name = "vcc-dram";
+};
+
+&reg_dcdc6 {
+	regulator-always-on;
+	regulator-min-microvolt = <1100000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-sys";
+};
+
+&reg_dldo1 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-hdmi";
+};
+
+&reg_dldo2 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-mipi";
+};
+
+&reg_dldo4 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi";
+};
+
+&reg_eldo1 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "cpvdd";
+};
+
+&reg_fldo1 {
+	regulator-min-microvolt = <1200000>;
+	regulator-max-microvolt = <1200000>;
+	regulator-name = "vcc-1v2-hsic";
+};
+
+/*
+ * The A64 chip cannot work without this regulator off, although
+ * it seems to be only driving the AR100 core.
+ * Maybe we don't still know well about CPUs domain.
+ */
+&reg_fldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1100000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-cpus";
+};
+
+&reg_rtc_ldo {
+	regulator-name = "vcc-rtc";
+};
+
+/* On Euler connector */
+&spdif {
+	status = "disabled";
+};
+
+/* On Exp and Euler connectors */
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pins_a>;
 	status = "okay";
 };
 
+/* On Wifi/BT connector, with RTS/CTS */
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+	status = "disabled";
+};
+
+/* On Pi-2 connector */
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
+	status = "disabled";
+};
+
+/* On Euler connector */
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>;
+	status = "disabled";
+};
+
+/* On Euler connector, RTS/CTS optional */
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4_pins>;
+	status = "disabled";
+};
+
 &usb_otg {
 	dr_mode = "host";
 	status = "okay";

arch/arm/dts/sun50i-a64-sopine-baseboard.dts

@@ -0,0 +1,150 @@
+/*
+ * Copyright (c) 2017 Icenowy Zheng <icenowy@aosc.xyz>
+ *
+ * Based on sun50i-a64-pine64.dts, which is:
+ *   Copyright (c) 2016 ARM Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This library is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This library is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "sun50i-a64-sopine.dtsi"
+
+/ {
+	model = "SoPine with baseboard";
+	compatible = "pine64,sopine-baseboard", "pine64,sopine",
+		     "allwinner,sun50i-a64";
+
+	aliases {
+		ethernet0 = &emac;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reg_vcc1v8: vcc1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii_pins>;
+	phy-mode = "rgmii";
+	phy-handle = <&ext_rgmii_phy>;
+	phy-supply = <&reg_dc1sw>;
+	status = "okay";
+};
+
+&mdio {
+	ext_rgmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_pins>;
+	vmmc-supply = <&reg_dcdc1>;
+	vqmmc-supply = <&reg_vcc1v8>;
+	bus-width = <8>;
+	non-removable;
+	cap-mmc-hw-reset;
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&reg_dc1sw {
+	regulator-name = "vcc-phy";
+};
+
+&reg_dldo1 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-hdmi";
+};
+
+&reg_dldo2 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-mipi";
+};
+
+&reg_dldo4 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins_a>;
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usbphy {
+	status = "okay";
+};

arch/arm/dts/sun50i-a64-sopine.dtsi

@@ -0,0 +1,142 @@
+/*
+ * Copyright (c) 2017 Icenowy Zheng <icenowy@aosc.xyz>
+ *
+ * Based on sun50i-a64-pine64.dts, which is:
+ *   Copyright (c) 2016 ARM Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This library is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This library is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "sun50i-a64.dtsi"
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins>;
+	vmmc-supply = <&reg_dcdc1>;
+	non-removable;
+	disable-wp;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&r_rsb {
+	status = "okay";
+
+	axp803: pmic@3a3 {
+		compatible = "x-powers,axp803";
+		reg = <0x3a3>;
+		interrupt-parent = <&r_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+#include "axp803.dtsi"
+
+&reg_aldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-pl";
+};
+
+&reg_aldo3 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "vcc-pll-avcc";
+};
+
+&reg_dcdc1 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-3v3";
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1040000>;
+	regulator-max-microvolt = <1300000>;
+	regulator-name = "vdd-cpux";
+};
+
+/* DCDC3 is polyphased with DCDC2 */
+
+&reg_dcdc5 {
+	regulator-always-on;
+	regulator-min-microvolt = <1200000>;
+	regulator-max-microvolt = <1200000>;
+	regulator-name = "vcc-dram";
+};
+
+&reg_dcdc6 {
+	regulator-always-on;
+	regulator-min-microvolt = <1100000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-sys";
+};
+
+&reg_eldo1 {
+	regulator-always-on;
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-name = "vdd-1v8-lpddr";
+};
+
+&reg_fldo1 {
+	regulator-min-microvolt = <1200000>;
+	regulator-max-microvolt = <1200000>;
+	regulator-name = "vcc-1v2-hsic";
+};
+
+/*
+ * The A64 chip cannot work without this regulator off, although
+ * it seems to be only driving the AR100 core.
+ * Maybe we don't still know well about CPUs domain.
+ */
+&reg_fldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1100000>;
+	regulator-max-microvolt = <1100000>;
+	regulator-name = "vdd-cpus";
+};
+
+&reg_rtc_ldo {
+	regulator-name = "vcc-rtc";
+};

arch/arm/dts/sun50i-a64.dtsi

@@ -43,6 +43,7 @@
  */
 
 #include <dt-bindings/clock/sun50i-a64-ccu.h>
+#include <dt-bindings/clock/sun8i-r-ccu.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/reset/sun50i-a64-ccu.h>
 
@@ -51,6 +52,26 @@
 	#address-cells = <1>;
 	#size-cells = <1>;
 
+	chosen {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+/*
+ * The pipeline mixer0-lcd0 depends on clock CLK_MIXER0 from DE2 CCU.
+ * However there is no support for this clock on A64 yet, so we depend
+ * on the upstream clocks here to keep them (and thus CLK_MIXER0) up.
+ */
+		simplefb_lcd: framebuffer-lcd {
+			compatible = "allwinner,simple-framebuffer",
+				     "simple-framebuffer";
+			allwinner,pipeline = "mixer0-lcd0";
+			clocks = <&ccu CLK_TCON0>,
+				 <&ccu CLK_DE>, <&ccu CLK_BUS_DE>;
+			status = "disabled";
+		};
+	};
+
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -111,6 +132,24 @@
 		method = "smc";
 	};
 
+	sound_spdif {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "On-board SPDIF";
+
+		simple-audio-card,cpu {
+			sound-dai = <&spdif>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&spdif_out>;
+		};
+	};
+
+	spdif_out: spdif-out {
+		#sound-dai-cells = <0>;
+		compatible = "linux,spdif-dit";
+	};
+
 	timer {
 		compatible = "arm,armv8-timer";
 		interrupts = <GIC_PPI 13
@@ -129,6 +168,23 @@
 		#size-cells = <1>;
 		ranges;
 
+		syscon: syscon@1c00000 {
+			compatible = "allwinner,sun50i-a64-system-controller",
+				"syscon";
+			reg = <0x01c00000 0x1000>;
+		};
+
+		dma: dma-controller@1c02000 {
+			compatible = "allwinner,sun50i-a64-dma";
+			reg = <0x01c02000 0x1000>;
+			interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_DMA>;
+			dma-channels = <8>;
+			dma-requests = <27>;
+			resets = <&ccu RST_BUS_DMA>;
+			#dma-cells = <1>;
+		};
+
 		mmc0: mmc@1c0f000 {
 			compatible = "allwinner,sun50i-a64-mmc";
 			reg = <0x01c0f000 0x1000>;
@@ -171,7 +227,7 @@
 			#size-cells = <0>;
 		};
 
-		usb_otg: usb@01c19000 {
+		usb_otg: usb@1c19000 {
 			compatible = "allwinner,sun8i-a33-musb";
 			reg = <0x01c19000 0x0400>;
 			clocks = <&ccu CLK_BUS_OTG>;
@@ -184,7 +240,7 @@
 			status = "disabled";
 		};
 
-		usbphy: phy@01c19400 {
+		usbphy: phy@1c19400 {
 			compatible = "allwinner,sun50i-a64-usb-phy";
 			reg = <0x01c19400 0x14>,
 			      <0x01c1a800 0x4>,
@@ -204,7 +260,7 @@
 			#phy-cells = <1>;
 		};
 
-		ehci0: usb@01c1a000 {
+		ehci0: usb@1c1a000 {
 			compatible = "allwinner,sun50i-a64-ehci", "generic-ehci";
 			reg = <0x01c1a000 0x100>;
 			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
@@ -216,7 +272,7 @@
 			status = "disabled";
 		};
 
-		ohci0: usb@01c1a400 {
+		ohci0: usb@1c1a400 {
 			compatible = "allwinner,sun50i-a64-ohci", "generic-ohci";
 			reg = <0x01c1a400 0x100>;
 			interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
@@ -226,7 +282,7 @@
 			status = "disabled";
 		};
 
-		ehci1: usb@01c1b000 {
+		ehci1: usb@1c1b000 {
 			compatible = "allwinner,sun50i-a64-ehci", "generic-ehci";
 			reg = <0x01c1b000 0x100>;
 			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
@@ -240,7 +296,7 @@
 			status = "disabled";
 		};
 
-		ohci1: usb@01c1b400 {
+		ohci1: usb@1c1b400 {
 			compatible = "allwinner,sun50i-a64-ohci", "generic-ohci";
 			reg = <0x01c1b400 0x100>;
 			interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
@@ -252,7 +308,7 @@
 			status = "disabled";
 		};
 
-		ccu: clock@01c20000 {
+		ccu: clock@1c20000 {
 			compatible = "allwinner,sun50i-a64-ccu";
 			reg = <0x01c20000 0x400>;
 			clocks = <&osc24M>, <&osc32k>;
@@ -273,6 +329,11 @@
 			interrupt-controller;
 			#interrupt-cells = <3>;
 
+			i2c0_pins: i2c0_pins {
+				pins = "PH0", "PH1";
+				function = "i2c0";
+			};
+
 			i2c1_pins: i2c1_pins {
 				pins = "PH2", "PH3";
 				function = "i2c1";
@@ -303,7 +364,37 @@
 				bias-pull-up;
 			};
 
-			uart0_pins_a: uart0@0 {
+			rmii_pins: rmii_pins {
+				pins = "PD10", "PD11", "PD13", "PD14", "PD17",
+				       "PD18", "PD19", "PD20", "PD22", "PD23";
+				function = "emac";
+				drive-strength = <40>;
+			};
+
+			rgmii_pins: rgmii_pins {
+				pins = "PD8", "PD9", "PD10", "PD11", "PD12",
+				       "PD13", "PD15", "PD16", "PD17", "PD18",
+				       "PD19", "PD20", "PD21", "PD22", "PD23";
+				function = "emac";
+				drive-strength = <40>;
+			};
+
+			spdif_tx_pin: spdif {
+				pins = "PH8";
+				function = "spdif";
+			};
+
+			spi0_pins: spi0 {
+				pins = "PC0", "PC1", "PC2", "PC3";
+				function = "spi0";
+			};
+
+			spi1_pins: spi1 {
+				pins = "PD0", "PD1", "PD2", "PD3";
+				function = "spi1";
+			};
+
+			uart0_pins_a: uart0 {
 				pins = "PB8", "PB9";
 				function = "uart0";
 			};
@@ -317,9 +408,73 @@
 				pins = "PG8", "PG9";
 				function = "uart1";
 			};
+
+			uart2_pins: uart2-pins {
+				pins = "PB0", "PB1";
+				function = "uart2";
+			};
+
+			uart3_pins: uart3-pins {
+				pins = "PD0", "PD1";
+				function = "uart3";
+			};
+
+			uart4_pins: uart4-pins {
+				pins = "PD2", "PD3";
+				function = "uart4";
+			};
+
+			uart4_rts_cts_pins: uart4-rts-cts-pins {
+				pins = "PD4", "PD5";
+				function = "uart4";
+			};
 		};
 
-		pwm: pwm@01c21400 {
+		spdif: spdif@1c21000 {
+			#sound-dai-cells = <0>;
+			compatible = "allwinner,sun50i-a64-spdif",
+				     "allwinner,sun8i-h3-spdif";
+			reg = <0x01c21000 0x400>;
+			interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_SPDIF>, <&ccu CLK_SPDIF>;
+			resets = <&ccu RST_BUS_SPDIF>;
+			clock-names = "apb", "spdif";
+			dmas = <&dma 2>;
+			dma-names = "tx";
+			pinctrl-names = "default";
+			pinctrl-0 = <&spdif_tx_pin>;
+			status = "disabled";
+		};
+
+		i2s0: i2s@1c22000 {
+			#sound-dai-cells = <0>;
+			compatible = "allwinner,sun50i-a64-i2s",
+				     "allwinner,sun8i-h3-i2s";
+			reg = <0x01c22000 0x400>;
+			interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2S0>, <&ccu CLK_I2S0>;
+			clock-names = "apb", "mod";
+			resets = <&ccu RST_BUS_I2S0>;
+			dma-names = "rx", "tx";
+			dmas = <&dma 3>, <&dma 3>;
+			status = "disabled";
+		};
+
+		i2s1: i2s@1c22400 {
+			#sound-dai-cells = <0>;
+			compatible = "allwinner,sun50i-a64-i2s",
+				     "allwinner,sun8i-h3-i2s";
+			reg = <0x01c22400 0x400>;
+			interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2S1>, <&ccu CLK_I2S1>;
+			clock-names = "apb", "mod";
+			resets = <&ccu RST_BUS_I2S1>;
+			dma-names = "rx", "tx";
+			dmas = <&dma 4>, <&dma 4>;
+			status = "disabled";
+		};
+
+		pwm: pwm@1c21400 {
 			compatible = "allwinner,sun50i-a64-pwm",
 				     "allwinner,sun5i-a13-pwm";
 			reg = <0x01c21400 0x8>;
@@ -334,8 +489,8 @@
 			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
-			clocks = <&ccu 67>;
-			resets = <&ccu 46>;
+			clocks = <&ccu CLK_BUS_UART0>;
+			resets = <&ccu RST_BUS_UART0>;
 			status = "disabled";
 		};
 
@@ -345,8 +500,8 @@
 			interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
-			clocks = <&ccu 68>;
-			resets = <&ccu 47>;
+			clocks = <&ccu CLK_BUS_UART1>;
+			resets = <&ccu RST_BUS_UART1>;
 			status = "disabled";
 		};
 
@@ -356,8 +511,8 @@
 			interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
-			clocks = <&ccu 69>;
-			resets = <&ccu 48>;
+			clocks = <&ccu CLK_BUS_UART2>;
+			resets = <&ccu RST_BUS_UART2>;
 			status = "disabled";
 		};
 
@@ -367,8 +522,8 @@
 			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
-			clocks = <&ccu 70>;
-			resets = <&ccu 49>;
+			clocks = <&ccu CLK_BUS_UART3>;
+			resets = <&ccu RST_BUS_UART3>;
 			status = "disabled";
 		};
 
@@ -378,8 +533,8 @@
 			interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
-			clocks = <&ccu 71>;
-			resets = <&ccu 50>;
+			clocks = <&ccu CLK_BUS_UART4>;
+			resets = <&ccu RST_BUS_UART4>;
 			status = "disabled";
 		};
 
@@ -387,8 +542,8 @@
 			compatible = "allwinner,sun6i-a31-i2c";
 			reg = <0x01c2ac00 0x400>;
 			interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&ccu 63>;
-			resets = <&ccu 42>;
+			clocks = <&ccu CLK_BUS_I2C0>;
+			resets = <&ccu RST_BUS_I2C0>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -398,8 +553,8 @@
 			compatible = "allwinner,sun6i-a31-i2c";
 			reg = <0x01c2b000 0x400>;
 			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&ccu 64>;
-			resets = <&ccu 43>;
+			clocks = <&ccu CLK_BUS_I2C1>;
+			resets = <&ccu RST_BUS_I2C1>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -409,13 +564,69 @@
 			compatible = "allwinner,sun6i-a31-i2c";
 			reg = <0x01c2b400 0x400>;
 			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&ccu 65>;
-			resets = <&ccu 44>;
+			clocks = <&ccu CLK_BUS_I2C2>;
+			resets = <&ccu RST_BUS_I2C2>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
 		};
 
+
+		spi0: spi@1c68000 {
+			compatible = "allwinner,sun8i-h3-spi";
+			reg = <0x01c68000 0x1000>;
+			interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
+			clock-names = "ahb", "mod";
+			dmas = <&dma 23>, <&dma 23>;
+			dma-names = "rx", "tx";
+			pinctrl-names = "default";
+			pinctrl-0 = <&spi0_pins>;
+			resets = <&ccu RST_BUS_SPI0>;
+			status = "disabled";
+			num-cs = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		spi1: spi@1c69000 {
+			compatible = "allwinner,sun8i-h3-spi";
+			reg = <0x01c69000 0x1000>;
+			interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
+			clock-names = "ahb", "mod";
+			dmas = <&dma 24>, <&dma 24>;
+			dma-names = "rx", "tx";
+			pinctrl-names = "default";
+			pinctrl-0 = <&spi1_pins>;
+			resets = <&ccu RST_BUS_SPI1>;
+			status = "disabled";
+			num-cs = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		emac: ethernet@1c30000 {
+			compatible = "allwinner,sun50i-a64-emac";
+			syscon = <&syscon>;
+			reg = <0x01c30000 0x10000>;
+			interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq";
+			resets = <&ccu RST_BUS_EMAC>;
+			reset-names = "stmmaceth";
+			clocks = <&ccu CLK_BUS_EMAC>;
+			clock-names = "stmmaceth";
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			mdio: mdio {
+				compatible = "snps,dwmac-mdio";
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
 		gic: interrupt-controller@1c81000 {
 			compatible = "arm,gic-400";
 			reg = <0x01c81000 0x1000>,
@@ -434,25 +645,61 @@
 				     <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
+		r_intc: interrupt-controller@1f00c00 {
+			compatible = "allwinner,sun50i-a64-r-intc",
+				     "allwinner,sun6i-a31-r-intc";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			reg = <0x01f00c00 0x400>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
 		r_ccu: clock@1f01400 {
 			compatible = "allwinner,sun50i-a64-r-ccu";
 			reg = <0x01f01400 0x100>;
-			clocks = <&osc24M>, <&osc32k>, <&iosc>;
-			clock-names = "hosc", "losc", "iosc";
+			clocks = <&osc24M>, <&osc32k>, <&iosc>,
+				 <&ccu 11>;
+			clock-names = "hosc", "losc", "iosc", "pll-periph";
 			#clock-cells = <1>;
 			#reset-cells = <1>;
 		};
 
-		r_pio: pinctrl@01f02c00 {
+		r_pio: pinctrl@1f02c00 {
 			compatible = "allwinner,sun50i-a64-r-pinctrl";
 			reg = <0x01f02c00 0x400>;
 			interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&r_ccu 3>, <&osc24M>, <&osc32k>;
+			clocks = <&r_ccu CLK_APB0_PIO>, <&osc24M>, <&osc32k>;
 			clock-names = "apb", "hosc", "losc";
 			gpio-controller;
 			#gpio-cells = <3>;
 			interrupt-controller;
 			#interrupt-cells = <3>;
+
+			r_rsb_pins: rsb {
+				pins = "PL0", "PL1";
+				function = "s_rsb";
+			};
+		};
+
+		r_rsb: rsb@1f03400 {
+			compatible = "allwinner,sun8i-a23-rsb";
+			reg = <0x01f03400 0x400>;
+			interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&r_ccu 6>;
+			clock-frequency = <3000000>;
+			resets = <&r_ccu 2>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&r_rsb_pins>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		wdt0: watchdog@1c20ca0 {
+			compatible = "allwinner,sun50i-a64-wdt",
+				     "allwinner,sun6i-a31-wdt";
+			reg = <0x01c20ca0 0x20>;
+			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
 		};
 	};
 };

arch/arm/dts/sun50i-h5-libretech-all-h3-cc.dts

@@ -1,11 +1,12 @@
 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
 /*
- * Copyright (C) 2018 Chen-Yu Tsai <wens@csie.org>
+ * Copyright (C) 2018 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
  */
 
 /dts-v1/;
 #include "sun50i-h5.dtsi"
-#include "sunxi-libretech-all-h3-cc.dtsi"
+#include <sunxi-libretech-all-h3-cc.dtsi>
 
 / {
 	model = "Libre Computer Board ALL-H3-CC H5";

arch/arm/dts/sun50i-h5-nanopi-neo-plus2.dts

@@ -1,18 +1,18 @@
 /*
  * Copyright (C) 2017 Antony Antony <antony@phenome.org>
- * Copyright (c) 2016 ARM Ltd.
+ * Copyright (C) 2016 ARM Ltd.
  *
  * This file is dual-licensed: you can use it either under the terms
  * of the GPL or the X11 license, at your option. Note that this dual
  * licensing only applies to this file, and not this project as a
  * whole.
  *
- *  a) This library is free software; you can redistribute it and/or
+ *  a) This file is free software; you can redistribute it and/or
  *     modify it under the terms of the GNU General Public License as
  *     published by the Free Software Foundation; either version 2 of the
  *     License, or (at your option) any later version.
  *
- *     This library is distributed in the hope that it will be useful,
+ *     This file is distributed in the hope that it will be useful,
  *     but WITHOUT ANY WARRANTY; without even the implied warranty of
  *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  *     GNU General Public License for more details.
@@ -42,16 +42,18 @@
  */
 
 /dts-v1/;
-
 #include "sun50i-h5.dtsi"
 
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
 
 / {
-	model = "FriendlyARM NanoPi NEO Plus 2";
+	model = "FriendlyARM NanoPi NEO Plus2";
 	compatible = "friendlyarm,nanopi-neo-plus2", "allwinner,sun50i-h5";
 
 	aliases {
+		ethernet0 = &emac;
 		serial0 = &uart0;
 	};
 
@@ -59,28 +61,116 @@
 		stdout-path = "serial0:115200n8";
 	};
 
+	leds {
+		compatible = "gpio-leds";
+
+		pwr {
+			label = "nanopi:green:pwr";
+			gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+
+		status {
+			label = "nanopi:red:status";
+			gpios = <&pio 0 20 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	reg_gmac_3v3: gmac-3v3 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		regulator-name = "gmac-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <100000>;
+		enable-active-high;
+		gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
+	};
+
 	reg_vcc3v3: vcc3v3 {
 		compatible = "regulator-fixed";
 		regulator-name = "vcc3v3";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 	};
+
+	vdd_cpux: gpio-regulator {
+		compatible = "regulator-gpio";
+		pinctrl-names = "default";
+		regulator-name = "vdd-cpux";
+		regulator-type = "voltage";
+		regulator-boot-on;
+		regulator-always-on;
+		regulator-min-microvolt = <1100000>;
+		regulator-max-microvolt = <1300000>;
+		regulator-ramp-delay = <50>; /* 4ms */
+		gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>;
+		gpios-states = <0x1>;
+		states = <1100000 0x0
+			  1300000 0x1>;
+	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		pinctrl-names = "default";
+		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+		post-power-on-delay-ms = <200>;
+	};
 };
 
-&ehci1 {
+&codec {
+	allwinner,audio-routing =
+		"Line Out", "LINEOUT",
+		"MIC1", "Mic",
+		"Mic",  "MBIAS";
 	status = "okay";
 };
 
+&ehci0 {
+	status = "okay";
+};
+
+&ehci3 {
+	status = "okay";
+};
+
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emac_rgmii_pins>;
+	phy-supply = <&reg_gmac_3v3>;
+	phy-handle = <&ext_rgmii_phy>;
+	phy-mode = "rgmii";
+	status = "okay";
+};
+
+&external_mdio {
+	ext_rgmii_phy: ethernet-phy@7 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <7>;
+	};
+};
+
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
-	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
-	cd-inverted;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
 	status = "okay";
 };
 
+&mmc1 {
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc3v3>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
 &mmc2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc2_8bit_pins>;
@@ -91,7 +181,11 @@
 	status = "okay";
 };
 
-&ohci1 {
+&ohci0 {
+	status = "okay";
+};
+
+&ohci3 {
 	status = "okay";
 };
 
@@ -101,6 +195,12 @@
 	status = "okay";
 };
 
-&usbphy {
+&usb_otg {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usbphy {
+	/* USB Type-A ports' VBUS is always on */
 	status = "okay";
 };

arch/arm/dts/sun50i-h5-nanopi-neo2.dts

@@ -1,18 +1,17 @@
 /*
  * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
- * Copyright (C) 2017 Jagan Teki <jteki@openedev.com>
  *
  * This file is dual-licensed: you can use it either under the terms
  * of the GPL or the X11 license, at your option. Note that this dual
  * licensing only applies to this file, and not this project as a
  * whole.
  *
- *  a) This library is free software; you can redistribute it and/or
+ *  a) This file is free software; you can redistribute it and/or
  *     modify it under the terms of the GNU General Public License as
  *     published by the Free Software Foundation; either version 2 of the
  *     License, or (at your option) any later version.
  *
- *     This library is distributed in the hope that it will be useful,
+ *     This file is distributed in the hope that it will be useful,
  *     but WITHOUT ANY WARRANTY; without even the implied warranty of
  *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  *     GNU General Public License for more details.
@@ -42,7 +41,6 @@
  */
 
 /dts-v1/;
-
 #include "sun50i-h5.dtsi"
 
 #include <dt-bindings/gpio/gpio.h>
@@ -52,6 +50,7 @@
 	compatible = "friendlyarm,nanopi-neo2", "allwinner,sun50i-h5";
 
 	aliases {
+		ethernet0 = &emac;
 		serial0 = &uart0;
 	};
 
@@ -59,28 +58,102 @@
 		stdout-path = "serial0:115200n8";
 	};
 
+	leds {
+		compatible = "gpio-leds";
+
+		pwr {
+			label = "nanopi:green:pwr";
+			gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+
+		status {
+			label = "nanopi:blue:status";
+			gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	reg_gmac_3v3: gmac-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "gmac-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <100000>;
+		enable-active-high;
+		gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
+	};
+
 	reg_vcc3v3: vcc3v3 {
 		compatible = "regulator-fixed";
 		regulator-name = "vcc3v3";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 	};
+
+	reg_usb0_vbus: usb0-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb0-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
+		status = "okay";
+	};
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci3 {
+	status = "okay";
+};
+
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emac_rgmii_pins>;
+	phy-supply = <&reg_gmac_3v3>;
+	phy-handle = <&ext_rgmii_phy>;
+	phy-mode = "rgmii";
+	status = "okay";
+};
+
+&external_mdio {
+	ext_rgmii_phy: ethernet-phy@7 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <7>;
+	};
 };
 
 &mmc0 {
-	compatible = "allwinner,sun50i-h5-mmc",
-		     "allwinner,sun50i-a64-mmc",
-		     "allwinner,sun5i-a13-mmc";
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
 	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
 	status = "okay";
 };
 
+&ohci0 {
+	status = "okay";
+};
+
+&ohci3 {
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pins_a>;
 	status = "okay";
 };
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usbphy {
+	/* USB Type-A port's VBUS is always on */
+	usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+	usb0_vbus-supply = <&reg_usb0_vbus>;
+	status = "okay";
+};

arch/arm/dts/sun50i-h5-orangepi-pc2.dts

@@ -1,17 +1,17 @@
 /*
- * Copyright (c) 2016 ARM Ltd.
+ * Copyright (C) 2016 ARM Ltd.
  *
  * This file is dual-licensed: you can use it either under the terms
  * of the GPL or the X11 license, at your option. Note that this dual
  * licensing only applies to this file, and not this project as a
  * whole.
  *
- *  a) This library is free software; you can redistribute it and/or
+ *  a) This file is free software; you can redistribute it and/or
  *     modify it under the terms of the GNU General Public License as
  *     published by the Free Software Foundation; either version 2 of the
  *     License, or (at your option) any later version.
  *
- *     This library is distributed in the hope that it will be useful,
+ *     This file is distributed in the hope that it will be useful,
  *     but WITHOUT ANY WARRANTY; without even the implied warranty of
  *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  *     GNU General Public License for more details.
@@ -41,36 +41,99 @@
  */
 
 /dts-v1/;
-
 #include "sun50i-h5.dtsi"
 
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
 
 / {
-	model = "OrangePi PC 2";
-	compatible = "xunlong,orangepi-pc-2", "allwinner,sun50i-h5";
+	model = "Xunlong Orange Pi PC 2";
+	compatible = "xunlong,orangepi-pc2", "allwinner,sun50i-h5";
+
+	reg_vcc3v3: vcc3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
 
 	aliases {
-		serial0 = &uart0;
 		ethernet0 = &emac;
+		serial0 = &uart0;
 	};
 
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
 
-	memory {
-		reg = <0x40000000 0x40000000>;
-	};
+	connector {
+		compatible = "hdmi-connector";
+		type = "a";
 
-	soc {
-		reg_vcc3v3: vcc3v3 {
-			compatible = "regulator-fixed";
-			regulator-name = "vcc3v3";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
 		};
 	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		pwr {
+			label = "orangepi:green:pwr";
+			gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+
+		status {
+			label = "orangepi:red:status";
+			gpios = <&pio 0 20 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	r-gpio-keys {
+		compatible = "gpio-keys";
+
+		sw4 {
+			label = "sw4";
+			linux,code = <BTN_0>;
+			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	reg_gmac_3v3: gmac-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "gmac-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <100000>;
+		enable-active-high;
+		gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
+	};
+
+	reg_usb0_vbus: usb0-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb0-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
+		status = "okay";
+	};
+};
+
+&codec {
+	allwinner,audio-routing =
+		"Line Out", "LINEOUT",
+		"MIC1", "Mic",
+		"Mic",  "MBIAS";
+	status = "okay";
+};
+
+&de {
+	status = "okay";
 };
 
 &ehci0 {
@@ -81,11 +144,20 @@
 	status = "okay";
 };
 
+&ehci2 {
+	status = "okay";
+};
+
+&ehci3 {
+	status = "okay";
+};
+
 &emac {
 	pinctrl-names = "default";
 	pinctrl-0 = <&emac_rgmii_pins>;
-	phy-mode = "rgmii";
+	phy-supply = <&reg_gmac_3v3>;
 	phy-handle = <&ext_rgmii_phy>;
+	phy-mode = "rgmii";
 	status = "okay";
 };
 
@@ -96,16 +168,26 @@
 	};
 };
 
-&mmc0 {
-	compatible = "allwinner,sun50i-h5-mmc",
-		     "allwinner,sun50i-a64-mmc",
-		     "allwinner,sun5i-a13-mmc";
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&ir {
 	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+	pinctrl-0 = <&ir_pins_a>;
+	status = "okay";
+};
+
+&mmc0 {
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
-	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
-	cd-inverted;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
 	status = "okay";
 };
 
@@ -117,17 +199,40 @@
 	status = "okay";
 };
 
+&ohci2 {
+	status = "okay";
+};
+
+&ohci3 {
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pins_a>;
 	status = "okay";
 };
 
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	status = "disabled";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
+	status = "disabled";
+};
+
 &usb_otg {
 	dr_mode = "otg";
 	status = "okay";
 };
 
 &usbphy {
+	/* USB Type-A ports' VBUS is always on */
+	usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+	usb0_vbus-supply = <&reg_usb0_vbus>;
 	status = "okay";
 };

arch/arm/dts/sun50i-h5-orangepi-prime.dts

@@ -1,17 +1,20 @@
 /*
- * Copyright (C) 2017 Jagan Teki <jteki@openedev.com>
+ * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.xyz>
+ *
+ * Based on sun50i-h5-orangepi-pc2.dts, which is:
+ *   Copyright (C) 2016 ARM Ltd.
  *
  * This file is dual-licensed: you can use it either under the terms
  * of the GPL or the X11 license, at your option. Note that this dual
  * licensing only applies to this file, and not this project as a
  * whole.
  *
- *  a) This library is free software; you can redistribute it and/or
+ *  a) This file is free software; you can redistribute it and/or
  *     modify it under the terms of the GNU General Public License as
  *     published by the Free Software Foundation; either version 2 of the
  *     License, or (at your option) any later version.
  *
- *     This library is distributed in the hope that it will be useful,
+ *     This file is distributed in the hope that it will be useful,
  *     but WITHOUT ANY WARRANTY; without even the implied warranty of
  *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  *     GNU General Public License for more details.
@@ -41,16 +44,17 @@
  */
 
 /dts-v1/;
-
 #include "sun50i-h5.dtsi"
 
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
 
 / {
-	model = "OrangePi Prime";
+	model = "Xunlong Orange Pi Prime";
 	compatible = "xunlong,orangepi-prime", "allwinner,sun50i-h5";
 
 	aliases {
+		ethernet0 = &emac;
 		serial0 = &uart0;
 	};
 
@@ -58,18 +62,85 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	memory {
-		reg = <0x40000000 0x80000000>;
-	};
+	connector {
+		compatible = "hdmi-connector";
+		type = "a";
 
-	soc {
-		reg_vcc3v3: vcc3v3 {
-			compatible = "regulator-fixed";
-			regulator-name = "vcc3v3";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
 		};
 	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		pwr {
+			label = "orangepi:green:pwr";
+			gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+
+		status {
+			label = "orangepi:red:status";
+			gpios = <&pio 0 20 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	r-gpio-keys {
+		compatible = "gpio-keys";
+
+		sw4 {
+			label = "sw4";
+			linux,code = <BTN_0>;
+			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	reg_gmac_3v3: gmac-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "gmac-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <100000>;
+		enable-active-high;
+		gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
+	};
+
+	reg_vcc3v3: vcc3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_usb0_vbus: usb0-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb0-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
+		status = "okay";
+	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&pio 2 14 GPIO_ACTIVE_LOW>; /* PC14 */
+	};
+};
+
+&codec {
+	allwinner,audio-routing =
+		"Line Out", "LINEOUT",
+		"MIC1", "Mic",
+		"Mic",  "MBIAS";
+	status = "okay";
+};
+
+&de {
+	status = "okay";
 };
 
 &ehci0 {
@@ -80,16 +151,58 @@
 	status = "okay";
 };
 
-&mmc0 {
-	compatible = "allwinner,sun50i-h5-mmc",
-		     "allwinner,sun50i-a64-mmc",
-		     "allwinner,sun5i-a13-mmc";
+&ehci2 {
+	status = "okay";
+};
+
+&ehci3 {
+	status = "okay";
+};
+
+&emac {
 	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+	pinctrl-0 = <&emac_rgmii_pins>;
+	phy-supply = <&reg_gmac_3v3>;
+	phy-handle = <&ext_rgmii_phy>;
+	phy-mode = "rgmii";
+	status = "okay";
+};
+
+&external_mdio {
+	ext_rgmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&ir {
+	pinctrl-names = "default";
+	pinctrl-0 = <&ir_pins_a>;
+	status = "okay";
+};
+
+&mmc0 {
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
-	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
-	cd-inverted;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+	status = "okay";
+};
+
+&mmc1 {
+	vmmc-supply = <&reg_vcc3v3>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
 	status = "okay";
 };
 
@@ -101,17 +214,40 @@
 	status = "okay";
 };
 
+&ohci2 {
+	status = "okay";
+};
+
+&ohci3 {
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pins_a>;
 	status = "okay";
 };
 
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	status = "disabled";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
+	status = "disabled";
+};
+
 &usb_otg {
 	dr_mode = "otg";
 	status = "okay";
 };
 
 &usbphy {
+	/* USB Type-A ports' VBUS is always on */
+	usb0_id_det-gpios = <&pio 0 21 GPIO_ACTIVE_HIGH>; /* PA21 */
+	usb0_vbus-supply = <&reg_usb0_vbus>;
 	status = "okay";
 };

arch/arm/dts/sun50i-h5-orangepi-zero-plus2.dts

@@ -46,7 +46,6 @@
 
 #include <dt-bindings/gpio/gpio.h>
 
-
 / {
 	model = "OrangePi Zero Plus2";
 	compatible = "xunlong,orangepi-zero-plus2", "allwinner,sun50i-h5";
@@ -59,27 +58,70 @@
 		stdout-path = "serial0:115200n8";
 	};
 
+	connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
 	reg_vcc3v3: vcc3v3 {
 		compatible = "regulator-fixed";
 		regulator-name = "vcc3v3";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		pinctrl-names = "default";
+		reset-gpios = <&pio 0 9 GPIO_ACTIVE_LOW>; /* PA9 */
+		post-power-on-delay-ms = <200>;
+	};
+};
+
+&de {
+	status = "okay";
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
 };
 
 &mmc0 {
-	compatible = "allwinner,sun50i-h5-mmc",
-		     "allwinner,sun50i-a64-mmc",
-		     "allwinner,sun5i-a13-mmc";
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
-	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
-	cd-inverted;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
 
+&mmc1 {
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc3v3>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+		interrupt-parent = <&r_pio>;
+		interrupts = <0 7 IRQ_TYPE_LEVEL_LOW>;	/* PL7 */
+		interrupt-names = "host-wake";
+	};
+};
+
 &mmc2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc2_8bit_pins>;
@@ -95,3 +137,9 @@
 	pinctrl-0 = <&uart0_pins_a>;
 	status = "okay";
 };
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+	status = "okay";
+};

arch/arm/dts/sun50i-h5.dtsi

@@ -1,17 +1,17 @@
 /*
- * Copyright (c) 2016 ARM Ltd.
+ * Copyright (C) 2016 ARM Ltd.
  *
  * This file is dual-licensed: you can use it either under the terms
  * of the GPL or the X11 license, at your option. Note that this dual
  * licensing only applies to this file, and not this project as a
  * whole.
  *
- *  a) This library is free software; you can redistribute it and/or
+ *  a) This file is free software; you can redistribute it and/or
  *     modify it under the terms of the GNU General Public License as
  *     published by the Free Software Foundation; either version 2 of the
  *     License, or (at your option) any later version.
  *
- *     This library is distributed in the hope that it will be useful,
+ *     This file is distributed in the hope that it will be useful,
  *     but WITHOUT ANY WARRANTY; without even the implied warranty of
  *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  *     GNU General Public License for more details.
@@ -40,24 +40,38 @@
  *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
-#include "sun8i-h3.dtsi"
+#include <sunxi-h3-h5.dtsi>
 
 / {
 	cpus {
-		cpu@0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
 			compatible = "arm,cortex-a53", "arm,armv8";
+			device_type = "cpu";
+			reg = <0>;
 			enable-method = "psci";
 		};
+
 		cpu@1 {
 			compatible = "arm,cortex-a53", "arm,armv8";
+			device_type = "cpu";
+			reg = <1>;
 			enable-method = "psci";
 		};
+
 		cpu@2 {
 			compatible = "arm,cortex-a53", "arm,armv8";
+			device_type = "cpu";
+			reg = <2>;
 			enable-method = "psci";
 		};
+
 		cpu@3 {
 			compatible = "arm,cortex-a53", "arm,armv8";
+			device_type = "cpu";
+			reg = <3>;
 			enable-method = "psci";
 		};
 	};
@@ -69,6 +83,14 @@
 
 	timer {
 		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13
+				(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14
+				(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11
+				(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10
+				(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
 	};
 };
 
@@ -76,8 +98,8 @@
 	compatible = "allwinner,sun50i-h5-ccu";
 };
 
-&gic {
-	compatible = "arm,gic-400";
+&display_clocks {
+	compatible = "allwinner,sun50i-h5-de2-clk";
 };
 
 &mmc0 {
@@ -104,6 +126,6 @@
 &pio {
 	interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
 		     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
-		   <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
+		     <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
 	compatible = "allwinner,sun50i-h5-pinctrl";
 };

arch/arm/dts/sun8i-h2-plus-orangepi-zero.dts

@@ -49,7 +49,6 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
 
 / {
 	model = "Xunlong Orange Pi Zero";
@@ -58,6 +57,7 @@
 	aliases {
 		serial0 = &uart0;
 		/* ethernet0 is the H3 emac, defined in sun8i-h3.dtsi */
+		ethernet0 = &emac;
 		ethernet1 = &xr819;
 	};
 
@@ -92,9 +92,14 @@
 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>;
+		post-power-on-delay-ms = <200>;
 	};
 };
 
+&ehci0 {
+	status = "okay";
+};
+
 &ehci1 {
 	status = "okay";
 };
@@ -107,18 +112,13 @@
 };
 
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
-	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
-	cd-inverted;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
 	status = "okay";
 };
 
 &mmc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc1_pins_a>;
 	vmmc-supply = <&reg_vcc_wifi>;
 	mmc-pwrseq = <&wifi_pwrseq>;
 	bus-width = <4>;
@@ -134,17 +134,56 @@
 	};
 };
 
+&ohci0 {
+	status = "okay";
+};
+
 &ohci1 {
 	status = "okay";
 };
 
+&spi0 {
+	/* Disable SPI NOR by default: it optional on Orange Pi Zero boards */
+	status = "disabled";
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "mxicy,mx25l1606e", "winbond,w25q128";
+		reg = <0>;
+		spi-max-frequency = <40000000>;
+	};
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pins_a>;
 	status = "okay";
 };
 
-&usbphy {
-	/* USB VBUS is always on */
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	status = "disabled";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
+	status = "disabled";
+};
+
+&usb_otg {
+	dr_mode = "peripheral";
 	status = "okay";
 };
+
+&usbphy {
+	/*
+	 * USB Type-A port VBUS is always on. However, MicroUSB VBUS can only
+	 * power up the board; when it's used as OTG port, this VBUS is
+	 * always off even if the board is powered via GPIO pins.
+	 */
+	status = "okay";
+	usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+};

arch/arm/dts/sun8i-h3-bananapi-m2-plus.dts

@@ -46,13 +46,13 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
 
 / {
 	model = "Banana Pi BPI-M2-Plus";
 	compatible = "sinovoip,bpi-m2-plus", "allwinner,sun8i-h3";
 
 	aliases {
+		ethernet0 = &emac;
 		serial0 = &uart0;
 		serial1 = &uart1;
 	};
@@ -61,10 +61,20 @@
 		stdout-path = "serial0:115200n8";
 	};
 
+	connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
-		pinctrl-0 = <&pwr_led_bpi_m2p>;
 
 		pwr_led {
 			label = "bananapi-m2-plus:red:pwr";
@@ -76,7 +86,6 @@
 	gpio_keys {
 		compatible = "gpio-keys";
 		pinctrl-names = "default";
-		pinctrl-0 = <&sw_r_bpi_m2p>;
 
 		sw4 {
 			label = "power";
@@ -85,14 +94,27 @@
 		};
 	};
 
+	reg_gmac_3v3: gmac-3v3 {
+		      compatible = "regulator-fixed";
+		      regulator-name = "gmac-3v3";
+		      regulator-min-microvolt = <3300000>;
+		      regulator-max-microvolt = <3300000>;
+		      startup-delay-us = <100000>;
+		      enable-active-high;
+		      gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
+	};
+
 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		pinctrl-names = "default";
-		pinctrl-0 = <&wifi_en_bpi_m2p>;
 		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
 	};
 };
 
+&de {
+	status = "okay";
+};
+
 &ehci0 {
 	status = "okay";
 };
@@ -105,6 +127,33 @@
 	status = "okay";
 };
 
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emac_rgmii_pins>;
+	phy-supply = <&reg_gmac_3v3>;
+	phy-handle = <&ext_rgmii_phy>;
+	phy-mode = "rgmii";
+
+	status = "okay";
+};
+
+&external_mdio {
+	ext_rgmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
 &ir {
 	pinctrl-names = "default";
 	pinctrl-0 = <&ir_pins_a>;
@@ -112,18 +161,13 @@
 };
 
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
-	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
-	cd-inverted;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
 	status = "okay";
 };
 
 &mmc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc1_pins_a>;
 	vmmc-supply = <&reg_vcc3v3>;
 	vqmmc-supply = <&reg_vcc3v3>;
 	mmc-pwrseq = <&wifi_pwrseq>;
@@ -131,7 +175,7 @@
 	non-removable;
 	status = "okay";
 
-	brcmf: bcrmf@1 {
+	brcmf: wifi@1 {
 		reg = <1>;
 		compatible = "brcm,bcm4329-fmac";
 		interrupt-parent = <&pio>;
@@ -162,27 +206,9 @@
 	status = "okay";
 };
 
-&r_pio {
-	pwr_led_bpi_m2p: led_pins@0 {
-		allwinner,pins = "PL10";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-	};
-
-	sw_r_bpi_m2p: key_pins@0 {
-		allwinner,pins = "PL3";
-		allwinner,function = "gpio_in";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-	};
-
-	wifi_en_bpi_m2p: wifi_en_pin {
-		allwinner,pins = "PL7";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-	};
+&reg_usb0_vbus {
+	gpio = <&pio 3 11 GPIO_ACTIVE_HIGH>; /* PD11 */
+	status = "okay";
 };
 
 &uart0 {
@@ -193,7 +219,7 @@
 
 &uart1 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart1_pins_a>;
+	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
 	status = "okay";
 };
 
@@ -203,6 +229,8 @@
 };
 
 &usbphy {
-	/* USB VBUS is on as long as VCC-IO is on */
+	usb0_id_det-gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
+	usb0_vbus-supply = <&reg_usb0_vbus>;
+	/* USB host VBUS is on as long as VCC-IO is on */
 	status = "okay";
 };