currently gpio hog function is not tested with "ut dm gpio"
so add some basic tests for gpio hog functionality.
For this enable GPIO_HOG in sandbox_defconfig, add
in DTS some gpio hog entries, and add testcase in
"ut dm gpio" command.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
- sbi: Add newline to error message
- fu540: dts: Correct reg size of otp and dmc nodes
- Enhance reserved memory fixup about PMP information passed from OpenSBI
- sifive: fu540: Add gpio-restart support
- qemu-riscv: Update QEMU run command
- Assorted fixes related to reserved memory
- fu540: enable all cache ways from U-Boot proper
- use log functions in fdt_fixup
Replace printf() and debug() by log_err() and log_debug().
"No reserved memory region found in source FDT\n" is not an error but a
debug information.
%s/can not/cannot/ - use the more common spelling.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
fdtdec_get_addr_size_no_parent is not an optimized version if parent
node is already available with the caller.
Use fdtdec_get_addr_size_auto_parent to read the "reg" property
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Not all errors are fatal. If a reserved memory node already exists in the
destination device tree, we can continue to boot without failing.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Explicitly pass the "-bios" option to QEMU to run U-Boot, instead
of the "-kernel" option, as we know that "-bios" behavior will be
changed since QEMU 5.1.0.
This also updates validated QEMU version to 5.0.0.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Starting from OpenSBI v0.7, the SBI firmware inserts/fixes up the
reserved memory node for PMP protected memory regions. All RISC-V
boards need to copy the reserved memory node from the device tree
provided by the firmware to the device tree used by U-Boot.
Turn on CONFIG_OF_BOARD_FIXUP by default for OF_SEPARATE.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Rick Chen <rick@andestech.com>
The copy of reserved memory node from source dtb to destination dtb
can be avoided if they point to the same place. This is useful when
OF_PRIOR_STAGE is used.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Pull request for UEFI sub-system for efi-2020-07-rc6 (2)
Fix an incorrect update of the GD register in efi_get_variable_common().
Fix an incorrect check for an FDT reg property.
Fix a device tree used for Python testing.
test_efi_fit tests fail on RISC-V currently. This is due to the
RISC-V arch_fixup_fdt() checks the #size-cells of the root node
in order to correctly fix up the reserved memory node.
Per the DT binding, the /reserved-memory node requires both
<#address-cells> and <#size-cells> and they should use the same
values as the root node. For the root node, it's not very useful
if <#size-cells> is zero.
Update #size-cells to 1 so tests can pass.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
With commit 0d7c2913fd ("cmd: bootefi: Honor the address & size cells
properties correctly") addr was replaced by fdt_addr. But not in the check
against FDT_ADDR_T_NONE.
Fixes: 0d7c2913fd ("cmd: bootefi: Honor the address & size cells properties
correctly")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
efi_get_variable_common() does not use EFI_ENTRY(). So we should not use
EFI_EXIT() either.
Fixes: 767f6eeb01 ("efi_loader: variable: support variable authentication")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
- fix logo on mx6ul_14x14_evk with DM_VIDEO enabled
- fix banner string overwriting the logo on small displays
- fix splash warning when building for ARM64
- fix STM32 DSI driver to probe only on supported hardware
- fix memory corruption with DSI panel drivers
The EDP_LCDC_SEL bit has to be set correctly to select vop0 or
vop1, but so far we have set it in both conditions, which is not
correct.
Can someone verify this is the correct way round? vop1 -> set,
vop0 -> clear?
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Fill characteristics of DSI data link to platform data instead of
mipi device to avoid memory corruption.
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Fill characteristics of DSI data link to platform data instead of
mipi device to avoid memory corruption.
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Copy the DSI data link characteristics from panel
platform data to mipi DSI device.
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Add new fields "lanes, format & mode_flags" to structure
mipi_dsi_panel_plat.
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Get below warning on ARM64 platform, because the bmp_load_addr
is defined to u32.
common/splash.c: In function ‘splash_video_logo_load’:
common/splash.c:74:9: warning: cast to pointer from integer
of different size [-Wint-to-pointer-cast]
74 | memcpy((void *)bmp_load_addr, bmp_logo_bitmap,
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # bpi-m1+, bpi-m64
The commit 84a6a27ae3 ("rockchip: rk3188: init CPU freq in clock
driver") changed ARM clock from 600MHz to 1600MHz. It made boot
unstable due to the fact that PMIC at the start generates insufficient
voltage for operation. See also: commit f4f57c58b5 ("rockchip:
rk3188: Setup the armclk in spl").
Fixes commit 84a6a27ae3 ("rockchip: rk3188: init CPU freq in clock
driver").
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Move the setting for noc remap out of SPL code. Changing
noc remap inside SPL results in breaking back to BROM
boot.
Fixes commit c14fe2a8e1 ("rockchip: rk3188: Move SoC
one time setting into arch_cpu_init()").
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Fix EMAC register address calculation, address need to multiply
with sizeof(u32) or 4.
This fixes write to invalid address.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Pull request for UEFI sub-system for efi-2020-07-rc6
Corrections for variable definitions are provided:
* Correct size of secure boot related UEFI variables.
* Do not use int for storing an enum.
* Replace fdt_addr by fdt_size where needed.
Since commit:
commit 6333cbb381
Author: Michael Walle <michael@walle.cc>
Date: Thu May 7 00:11:58 2020 +0200
phy: atheros: ar8035: remove static clock config
We can configure the clock output in the device tree. Disable the
hardcoded one in here. This is highly board-specific and should have
never been enabled in the PHY driver.
If bisecting shows that this commit breaks your board it probably
depends on the clock output of your Atheros AR8035 PHY. Please have a
look at doc/device-tree-bindings/net/phy/atheros.txt. You need to set
"clk-out-frequency = <125000000>" because that value was the hardcoded
value until this commit.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
, the clock output setting for the AR803x driver is removed from being
hardcoded in the PHY driver and should be passed via device tree instead.
Update the device tree with the "qca,clk-out-frequency" property so that
Ethernet can work again.
Reported-by: Soeren Moch <smoch@web.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Soeren Moch <smoch@web.de>
The variables SetupMode, AuditMode, DeployedMode are explicitly defined as
UINT8 in the UEFI specification. The type of SecureBoot is UINT8 in EDK2.
Use variable name secure_boot instead of sec_boot for the value of the
UEFI variable SecureBoot.
Avoid abbreviations in function descriptions.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Variable efi_secure_mode is meant to hold a value of enum efi_secure_mode.
So it should not be defined as int but as enum efi_secure_mode.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Variable fdt_size should be of type 'fdt_size_t', not 'fdt_addr_t'.
Fixes 0d7c2913fd: ("cmd: bootefi: Honor the address & size cells properties correctly")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
SDHCI HISPD bits need to be configured based on desired mmc
timings mode and some HISPD quirks.
So, handle the HISPD bit based on the mmc computed selected
mode(timing parameter) rather than fixed mmc card clock
frequency.
Linux handle the HISPD similar like this in below commit but no
SDHCI_QUIRK_BROKEN_HISPD_MODE,
commit <501639bf2173> ("mmc: sdhci: fix SDHCI_QUIRK_NO_HISPD_BIT handling")
This eventually fixed the mmc write issue observed in
rk3399 sdhci controller.
Bug log for refernece,
=> gpt write mmc 0 $partitions
Writing GPT: mmc write failed
** Can't write to device 0 **
** Can't write to device 0 **
error!
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Peng Fan <peng.fan@nxp.com>
Peng Fan: added back "ctrl &= ~SDHCI_CTRL_HISPD;" per Jaehoon's suggestion
Tested-by: Suniel Mahesh <sunil@amarulasolutions.com> # roc-rk3399-pc
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
According to eMMC specification v5.1 section 6.4.3, we should issue
CMD1 repeatedly in the idle state until the eMMC is ready even if
mmc_send_op_cond() send CMD1 with argument = 0. Otherwise some eMMC
devices seems to enter the inactive mode after mmc_complete_op_cond()
issued CMD0 when the eMMC device is busy.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
In current code, we add 1ms dealy after each tuning command for standard
tuning method. Adding this 1ms dealy is because USDHC default check the
CMD CRC and DATA line. If detect the CMD CRC, USDHC standard tuning
IC logic do not wait for the tuning data sending out by the card, trigger
the buffer read ready interrupt immediately, and step to next cycle. So
when next time the new tuning command send out by USDHC, card may still
not send out the tuning data of the upper command，then some eMMC cards
may stuck, can't response to any command, block the whole tuning procedure.
If do not check the CMD CRC for tuning, then do not has this issue. USDHC
will wait for the tuning data of each tuning command and check them. If the
tuning data pass the check, it also means the CMD line also okay for tuning.
So this patch disable the CMD CRC check for tuning, save some time for the
whole tuning procedure.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
According the RM, the bit[6~0] of register ESDHC_TUNING_CTRL is
TUNING_START_TAP, bit[7] of this register is to disable the command
CRC check for standard tuning. So fix it here.
Fixes: fa33d20749 ("mmc: split fsl_esdhc driver for i.MX")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
The extcsd read target must be cache aligned in case the controller
uses DMA to read the extcsd register, make it so.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
This patch try to avoids eviction of dirty lines during DMA
transfer. The code right now execute the following step:
- allocate the buffer
- start a dma operation using the non-coherent dma buffer
- invalidate cache lines associated with the buffer
- read the buffer
This can lead to reading back not valid information, because the cache
controller could evict dirty cache lines belonging to the buffer *after*
the DMA operation has started to fill the DRAM.
In order to avoid this, a new invalidation is required *before* starting
the DMA operation. The patch just adds an invalidation before submitting
the DMA command.
Example below shows the nvme disk scan result without the following
patch
=> nvme scan
nvme_get_info_from_identify: nn = 544502629, vwc = 100,
sn = dev_0T, mn = `�\�, fr = t_part, mdts = 105
So, invalidating the cache before submitting the admin command,
fix the cpu read.
Cc: André Przywara <andre.przywara@arm.com>
Reported-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The correct name for the property is "qca,clk-out-frequency", so fix
it accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Commit 0528979fa7 ("part: Drop disk_partition_t typedef") changed to
a struct. As a result it uncovered an apparent missing include in
zfs_common.h for part.h which actually contains the definition. The ZFS
handles the struct exclusively as pointers so it was only a warning.
warning: ‘struct disk_partition’ declared inside parameter list
will not be visible outside of this definition or declaration
void zfs_set_blk_dev(struct blk_desc *rbdd, struct disk_partition *info);
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Series-CC: Simon Glass <sjg@chromium.org>
After enabling SPL_OF_CONTROL, SPL_DM and SPL_DM_MMC the MMC
initialization code is not longer needed.
This patch removes the unused code.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
In order to take the beneficts of DT and DM in SPL, like reusing the code
and avoid redundancy, enable SPL_OF_CONTROL, SPL_DM and SPL_DM_MMC.
With this new configuration SPL image is 50 KB, higher than the
38 KB from the previous version, but it still under the 68 KB limit.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
In SPL legacy code only one MMC device is created, based on BOOT_CFG
register, which can be either SD or eMMC. In this context
board_boot_order return always MMC1 when configure to boot from
SD/eMMC. After switching to DM both SD and eMMC devices are created
based on the information available on DT, but as board_boot_order
only returns MMC1 is not possible to boot from eMMC.
This patch customizes board_boot_order taking into account BOOT_CFG
register to point to correct MMC1 / MMC2 device. Additionally, handle
IO mux for the desired boot device.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Current aliases missed gpio0 node, and this node shoud be
aliased to gpio index 0 to align with i.MX8QXP. Otherwise, we
will get below message when running "gpio status" command, and
see the reason by "dm uclass".
=> gpio status
Device 'gpio@5d090000': seq 0 is in use by 'gpio@5d080000'
Device 'gpio@5d0a0000': seq 1 is in use by 'gpio@5d090000'
Device 'gpio@5d0b0000': seq 2 is in use by 'gpio@5d0a0000'
=> dm uclass
uclass 36: gpio
0 * gpio@5d080000 @ fbaefb90, seq 0, (req -1)
1 * gpio@5d090000 @ fbaefc70, seq 1, (req 0)
2 * gpio@5d0a0000 @ fbaefd50, seq 2, (req 1)
3 * gpio@5d0b0000 @ fbaefe30, seq 5, (req 2)
4 * gpio@5d0c0000 @ fbaeff10, seq 3, (req 3)
5 * gpio@5d0d0000 @ fbaefff0, seq 4, (req 4)
6 * gpio@5d0e0000 @ fbaf00d0, seq 6, (req 5)
7 * gpio@5d0f0000 @ fbaf01b0, seq 7, (req 6)
Signed-off-by: Ye Li <ye.li@nxp.com>
Since the i.MX8 GPIO banks are indexed from 0 not 1 on other i.MX
platforms, so we have to adjust the index accordingly.
Signed-off-by: Adrian Alonso <adrian.alonso@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
We need to change the environment offset to avoid corrupting the U-Boot
binary when saving it.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This fixes the boot from USB loader, which is critical to easy the
manufacture process.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Select default U-Boot and SPL text base for the MX7 SoC. The U-Boot
text base is picked as the one used by various MX7 boards. The SPL
text base however is different.
The SPL text base is set to 0x912000 instead of the usual 0x911000,
that is because the 0x911000 value cannot work. Using 0x911000 as a
SPL text base will result in the DCD header being placed below the
0x911000 address, which is a reserved SRAM area which must not be
used. This will actually trigger eMMC boot failure on MX7D at least.
Hence the increment.
Update all boards affected by this SPL problem to the new SPL_TEXT_BASE.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
There are systems where board_early_init_f() is plain empty. Switch
the config option from "select" to "imply", to permit user to unset
the BOARD_EARLY_INIT_F if it were to be empty.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The iMX7 defines further DDRC ZQCTLx registers, however those were
thus far missing from the list of registers and not programmed. On
systems with LPDDR2 or DDR3, those registers must be programmed with
correct values, otherwise the DRAM may not work. However, existing
systems which worked without programming these registers before are
now setting those registers to 0, which is the default value, so no
functional change there.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
This is needed to obtain the MAC from EEPROM/OTP only after the final
env is populated, otherwise the ethaddr might be overriden.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Claudius Heine <ch@denx.de>
Cc: Harald Seiler <hws@denx.de>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
For using a debug UART on the Wandboard CONFIG_MXC_UART=y must be set in
the .config file.
To avoid duplicate definitions move the setting from
include/configs/wandboard.h to configs/wandboard_defconfig.
Document the debug UART settings in the README.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
It appears that MMC access on the Sabrelite has been broken since
cdcaee9518:
Loading Environment from MMC... Card did not respond to voltage select!
*** Warning - No block device, using default environment
Remove the board_mmc_init() and related entries now that we should be
using DM_MMC, add PINCTRL so that things work as expected.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Troy Kisky <troy.kisky@boundarydevices.com>
1. Drop legacy emmcboot wrapper from env.
2. Change the "boot try" order. Default one is: SD -> eMMC -> USB -> DHCP
3. Drop DFU defines
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
1. Drop legacy emmcboot wrapper from env.
2. Change the "boot try" order. Default one is: SD -> eMMC -> USB -> DHCP
3. Drop DFU defines
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
1. Drop legacy emmcboot wrapper from env.
2. Change the "boot try" order. Default one is: SD -> eMMC -> USB -> DHCP
3. Drop DFU defines
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
This introduces automatic boot counter that increases after every
reset.After a power-on reset, it will be initialized with 1,
and each reboot will increment the value by 1. By default it's
disabled if bootlimit isn't set.
To enable this feature you have set bootcount limit ("bootlimit"),
alternate boot action ("altbootcmd") that will be performed if
the new value of bootcount exceeds the value of bootlimit, and
"upgrade_available" to let U-Boot automatically increase and save
the counter value after every reset:
> setenv bootlimit 5
> setenv upgrade_available 1
> setenv altbootcmd "bootm ..."
In case the bootlimit exceeds, the message will be shown and
albootcmd executed:
Warning: Bootlimit (5) exceeded. Using altbootcmd.
To reset bootcount run:
> bootcount reset
Print current value:
> bootcount print
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
s/fdt-module/fdt_module/g, as we don't use dash in fdt_file anymore.
Fixes: 4c63a601("apalis-tk1: support v1.2 hardware revision")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
1. Use distro_bootcmd as default boot command instead of
legacy emmcboot wrapper.
2. Drop emmcboot and sdboot wrappers.
3. Provide proper boot order for Distro Boot.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
The distro bootscript uses kernel_image to get the file name of
the kernel, so change that variable name.
UBI boot has precedence in the default boot command. If one wants
to boot from SD with a working NAND installation stop in U-Boot
and enter:
setenv fdtfile ${soc}-colibri-${fdt_board}.dtb && run distro_bootcmd
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
When using distro boot to boot from UBI volumes the boot partition
has been hardcoded to "UBI" (capital letters). However, our default
MTD layout uses "ubi" (lower case letter). Define "ubi" as the
default UBI partition for distro boot for Toradex. This allows to
use distro boot without having to redefine the MTD partition layout
which is useful for TorizonCore.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
This got dropped by a global 'make savedefconfig' resync as
required patches are still in flight.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
As per kernel commit 0672d22a1924 ("ARM: dts: imx: Fix the AR803X phy-mode)
the correct phy-mode should be "rgmii-id", so fix it accordingly
to fix the Ethernet regression.
This problem has been exposed by commit:
commit 13114f38e2
Author: Vladimir Oltean <vladimir.oltean@nxp.com>
Date: Thu May 7 00:11:51 2020 +0200
phy: atheros: Explicitly disable RGMII delays
To eliminate any doubts about the out-of-reset value of the PHY, that
the driver previously relied on.
If bisecting shows that this commit breaks your board you probably have
a wrong PHY interface mode. You probably want the
PHY_INTERFACE_MODE_RGMII_RXID or PHY_INTERFACE_MODE_RGMII_ID mode.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
As per kernel commit 0672d22a1924 ("ARM: dts: imx: Fix the AR803X phy-mode)
the correct phy-mode should be "rgmii-id", so fix it accordingly
to fix the Ethernet regression.
This problem has been exposed by commit:
commit 13114f38e2
Author: Vladimir Oltean <vladimir.oltean@nxp.com>
Date: Thu May 7 00:11:51 2020 +0200
phy: atheros: Explicitly disable RGMII delays
To eliminate any doubts about the out-of-reset value of the PHY, that
the driver previously relied on.
If bisecting shows that this commit breaks your board you probably have
a wrong PHY interface mode. You probably want the
PHY_INTERFACE_MODE_RGMII_RXID or PHY_INTERFACE_MODE_RGMII_ID mode.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Fix the phy-mode accordingly to fix the regression.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Migration to DM_ETH is mandatory, so convert mx6cuboxi to Ethernet
Driver Model.
This also brings the benefit of restoring Ethernet functionality.
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Tom Rini <trini@konsulko.com>
Sync the device tree with 5.8-rc1.
It basically contains the following extra kernel commit:
commit 86b08bd5b99480b79a25343f24c1b8c4ddcb5c09
Author: Russell King <rmk+kernel@armlinux.org.uk>
Date: Wed Apr 15 16:44:17 2020 +0100
ARM: dts: imx6-sr-som: add ethernet PHY configuration
Add ethernet PHY configuration ahead of removing the quirk that
configures the clocking mode for the PHY. The RGMII delay is
already set correctly.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
, which passes the 'qca,clk-out-frequency' property and it is important
to specify the correct frequency generated by the AR8035.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Tom Rini <trini@konsulko.com>
As we move towards driver model, it is required to let the FEC driver
know how to properly deal with an Ethernet PHY subnode in the device tree.
For example:
&fec {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_microsom_enet_ar8035>;
phy-handle = <&phy>;
phy-mode = "rgmii-id";
phy-reset-duration = <2>;
phy-reset-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
status = "okay";
mdio {
#address-cells = <1>;
#size-cells = <0>;
phy: ethernet-phy@0 {
reg = <0>;
qca,clk-out-frequency = <125000000>;
};
};
};
Currently the PHY node pointer is incorrectly associated with the
Ethernel controller instead of the PHY node itself.
This causes the PHY properties, such as "qca,clk-out-frequency" in
the example above to not get parsed.
Fix this problem by populating the phy_of_node node.
Suggested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Tom Rini <trini@konsulko.com>
The clock ouput frequency is calculated incorrectly for AR8035 due to
wrong masking of priv->clk_25m_reg and priv->clk_25m_mask.
This same issue has been already fixed in the kernel by:
commit b1f4c209d84057b6d40b939b6e4404854271d797
Author: Oleksij Rempel <o.rempel@pengutronix.de>
Date: Wed Apr 1 11:57:32 2020 +0200
net: phy: at803x: fix clock sink configuration on ATH8030 and ATH8035
The masks in priv->clk_25m_reg and priv->clk_25m_mask are one-bits-set
for the values that comprise the fields, not zero-bits-set.
This patch fixes the clock frequency configuration for ATH8030 and
ATH8035 Atheros PHYs by removing the erroneous "~".
To reproduce this bug, configure the PHY with the device tree binding
"qca,clk-out-frequency" and remove the machine specific PHY fixups.
Fixes: 2f664823a47021 ("net: phy: at803x: add device tree binding")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Apply the same fix in the U-Boot driver.
Tested on a i.MX6 Hummingboard.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Tested-by: Tom Rini <trini@konsulko.com>
The cd-gpios with (GPIO_ACTIVE_LOW | GPIO_PULL_UP) gpio is thus far
unsupported, reinstate the old cd-gpios behavior until this handling
is fully implemented. This avoid potential issue for SDCard boot:
the card detect fails with floating gpio.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
The cd-gpios with (GPIO_ACTIVE_LOW | GPIO_PULL_UP) gpio is thus far
unsupported, reinstate the old cd-gpios behavior until this handling
is fully implemented. This permits the DHSOM to boot from SD again,
without this patch the card detect fails.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
fdtdec_get_addr_size reads the uses a fixed value for address & size
cell properties which may not be correct always.
Use the auto variant of the function which automatically reads
#address-cells & #size-cells from parent and uses to read the "reg"
property.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
On 32 bit systems fdt_addr_t may be 4 bytes long but size is defined as
u64. Avoid filling the upper 4 bytes of the sizep parameter of
fdtdec_get_addr_size_auto_parent() with random bytes from the stack by
defining a separate variable fdt_size.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This allows Nano to use the key M.2 on the CVB to connect and use a M.2
NVMe SSD stick. Works on my Nano B00, WD SN750 NVMe SSD shows up
w/'nvme' commands. Will add booting from NVMe via distro cmds in a future
patch.
Signed-off-by: Tom Warren <twarren@nvidia.com>
The PSCI nodes are currently not populated for the Tegra210 and Tegra186
devices. This prevents the PSCI driver from being able to identify the
PSCI method used by these devices and causes the probe of the PSCI
driver to fail.
Since commit 81ea00838c ("efi_loader: PSCI reset and shutdown") was
added, which moves the PSCI EFI system reset handler into the PSCI
driver, this has prevented the EFI system reset from working for
Tegra210 and Tegra186. Therefore, populating these nodes is necessary
to fix the EFI system reset for Tegra210 and Tegra186.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
When CONFIG_OF_LIVE is enabled, dev_of_offset() cannot be used and
if used returns an invalid offset. This causes the call to
fdt_stringlist_get() in the psci_probe() to fail to read the 'method'
property from the PSCI node for the device and hence prevents PSCI
from working. Fix this by using the ofnode_read_string() API instead
of the fdt_stringlist_get() because this will handle reading the
property both when CONFIG_OF_LIVE is enabled or disabled.
Due to the above problem and since commit 81ea00838c ("efi_loader:
PSCI reset and shutdown") was added, the EFI system reset has been
broken for Tegra210 and Tegra196 platforms. This also fixes the EFI
system reset for these Tegra platforms.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
The ethernet PHY on all known Gen3 boards takes a while to come out
of reset, increase the auto-negotiation timeout to prevent it from
timing out in case the ethernet is used right after the board was
reset.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
After migration to DM 'vga' name is not longer supported,
change it to 'vidconsole' in the default environment.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Igor Opaniuk <igor.opaniuk@toradex.com>
After migration to DM 'vga' name is not longer supported,
change it to 'vidconsole' in the default environment.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Igor Opaniuk <igor.opaniuk@toradex.com>
After migration to DM 'vga' name is not longer supported,
change it to 'vidconsole' in the default environment.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Add the recently added reStructuredText board documentation in the
appropriate MAINTAINERS files.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Move the natural text Amlogic board README files to doc/board/amlogic
into reStructuredText and :
- add reStructuredText markup for bash code
- fix secondary titles markup
- move board support into global support matrix
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add OP-TEE firmware node in stm32mp15 U-Boot DTSI. This node is
needed since commit [1] that changed U-Boot/stm32mp15 to detect
OP-TEE availability by probing the resource instead of relying on
U-Boot configuration. The software sequence implemented by [1] is
fine but U-Boot DTS/DTSI files were not updated accordingly since,
hence OP-TEE presence is never detected by U-Boot, preventing Linux
kernel from using OP-TEE resources.
For consistency and to synchronize stm32mp15 DTSI files (excluding
U-Boot specific DTSI files) with the Linux kernel ones, this change
also moves the OP-TEE reserved memory nodes from board generic DTSI
files to U-Boot specific board DTSI files.
Link: [1] commit 43df0a159d ("stm32mp1: dynamically detect op-tee presence")
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Fix the sequence in stm32mp1 fdt.c that disables OP-TEE resources
defined in FDT when U-boot detects OP-TEE firmware is not present.
Before this change, helper function stm32_fdt_disable_optee()
set property status to "disabled" for the OP-TEE reserved memory
nodes but this has no impact since Linux kernel does not consider
the status property for reserved-memory subnodes. This change
make U-Boot to attempt to delete the node instead.
Fixes: 4a1b975dac ("board: stm32mp1: reserve memory for OP-TEE in device tree")
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
The fix in commit b7adcdd073 has the side-effect that the regulator
will be disabled when requesting the relevant gpio in
regulator_common_ofdata_to_platdata() and enabled in
regulator_pre_probe() when the regulator was already enabled.
This leads to a short interruption in the 3.3V power to the PCIe
slot on the firefly-rk3399 which makes an ADATA SX8000NP NVMe SSD
unhappy.
Fix this by setting the GPIOD_IS_OUT_ACTIVE flag again when the
'regulator-boot-on' property is set, but check for this property
explicitly instead of relying on the "boot_on" member of
the uclass platdata.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Tested-by: Patrice Chotard <patrice.chotard@st.com>
Update the comment for SYS_RELOC_GD_ENV_ADDR as gd->env_addr is updated
in board_r.c::initr_reloc_global_data() under the compilation flags
CONFIG_SYS_RELOC_GD_ENV_ADDR
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Several configutation options require additional memory before relocation:
* CONSOLE_RECORD
* LOG
* RSA
The current default of 0x400 is too small to encompass them all. Increase
the value of SYS_MALLOC_F_LEN to 0x2000 for ARCH_QEMU.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This reverts commit 0486497e2b.
The strtoul has well-defined semantics. It is defined by the C standard and
POSIX. To quote the relevant section of the man pages,
> If base is zero or 16, the string may then include a "0x" prefix, and the
> number will be read in base 16; otherwise, a zero base is taken as 10
> (decimal) unless the next character is '0', in which case it is taken as
> 8 (octal).
Keeping these semantics is important for several reasons. First, it is very
surprising for standard library functions to behave differently than usual.
Every other implementation of strtoul has different semantics than the
implementation in U-Boot at the moment. Second, it can result in very
surprising results from small changes. For example, changing the string
"1f" to "20" causes the parsed value to *decrease*. Forcing use of the "0x"
prefix to specify hexidecimal numbers is a feature, not a bug. Lastly, this
is slightly less performant, since the entire number is parsed twice.
This fixes the str_simple_strtoul test failing with
test/str_ut.c:29, run_strtoul(): expect_val == val: Expected 0x44b (1099), got 0x1099ab (1087915)
test/str_ut.c:46, str_simple_strtoul(): 0 == run_strtoul(uts, str2, 0, 1099, 4): Expected 0x0 (0), got 0x1 (1)
Signed-off-by: Sean Anderson <seanga2@gmail.com>
CC: Michal Simek <michal.simek@xilinx.com>
CC: Shiril Tichkule <shirilt@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
s/booot/boot/g
The first ase is booot instead of boot and second u-booot instead of
u-boot.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Fix the loop that parses FDT for a reserved memory node named "optee".
Before this change, if at least one subnode was found in the
reserved-memory node, the function endlessly looped since instruction
continue returned back in the loop without updating variable subnode.
This change fixes the issue by using a for loop.
Fixes: 6ccb05eae0 ("image: fdt: copy possible optee nodes to a loaded devicetree")
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Unsupported voltage on voltage switch is not an error, do not
print error message in such a case. This happens e.g. if the
eMMC is already in 1V8 mode or when testing 1V2 mode operation
on systems which only do 3V3/1V8 switching.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The 3V3/1V8 switching could never have worked on any of the iMXes
ever since 51313b49f2 ("mmc: fsl_esdhc: support SDR104 and HS200"),
because that commit uses priv->vqmmc_dev when switching voltages on
mode switch, while local vqmmc_dev in probe to store the regulator
pointer. Those are two different variables with the same name. So
the priv->vqmmc_dev was always NULL and thus voltage switch between
modes never really suceeded.
Fix this by assigning priv->vqmmc_dev with value of the vqmmc_dev
in probe.
Fixes: 51313b49f2 ("mmc: fsl_esdhc: support SDR104 and HS200")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
When eSDHC operates at 3.3v, damage can accumulate in an internal
level shifter at a higher than expected rate. The faster the interface
runs, the more damage accumulates. This issue now is found on LX2160A
eSDHC1 for only SD card.
The hardware workaround is recommended to use an on-board level shifter
that is 1.8v on SoC side and 3.3v on SD card side.
For boards without hardware workaround, this option could be enabled,
ensuring 1.8v IO voltage and disabling eSDHC if no card.
This option assumes no hotplug, and u-boot has to make all the way to
to linux to use 1.8v UHS-I speed mode if has card.
If you do not want the workaround for better user experience, of course
you can choose to not select it running eSDHC in unsafe mode.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
For size_t we have to use %zu for printing not %lu.
Fixes: 4540dabdca ("efi_loader: image_loader: support image
authentication")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Commit e71b6f6622 ("i2c: designware_i2c: Rewrite timing calculation")
change the hcnt and lcnt timing calculation. New timing calculation is
based on calculation from Designware i2c databook.
After this new timing calculation, hcnt will have negative value
with i2c-scl-falling-time-ns 5000 that set in socfpga_cyclone5_socdk.dts.
This patch overwrite i2c-scl-falling-time-ns to 300ns (default SCL fall
time used in Designware i2c driver) for Uboot.
Before the fix:
=> i2c dev 0
Setting bus to 0
Failure changing bus number (-22)
After the fix:
=> i2c dev 0
Setting bus to 0
=> i2c probe
Valid chip addresses: 17 51 55 5B 5C 5E 66 68 70
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Update the firmware to improve compatibility for none-intel USB
host controller. The more information is as following.
The device has auto-installed driver feature - via switch CD-ROM/NIC
mode. But in some corner cases, it would switch to CD-ROM unexpected.
This issue results in Lan Function Disabled.
While USB PHY transits to P3 from P0 due to the absent of transmitter
control, it would issues undefined signal to its link partner.
Some Down Stream Port misidentify the undefined signal as wakeup
signal. So the link state will not keep in suspend even the system
is idle.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Acked-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
OF_CONTROL, DM_SPI and other driver model migration deadlines
are expired for this board.
Remove it.
Acked-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
This would make SPL build to DM_SPL, SPL_OF_CONTROL.
Build fine with but not tested.
Cc: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
atmel_spi.h has register offsets, and atmel_spi_slave
structure, move it into .c file for better readability
and drop atmel_spi.h
Cc: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
- Deadline for DM migration already passed by months.
- Sent couple of zap patches and
- No response on dm conversation
hence removed the driver.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Order the macros, private structures and simple functions
in a proper way to have more code readability.
No functionality changed.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Deadline for DM migration already passed by months
and no response on full dm conversation hence removed
the nondm code.
Note: Look like there is no user for nondm code
for this driver.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
This reverts commit 1f63ee6566.
As reported by Ye Li on ML:
1. Removing the image_offset will break secondary (redundant) boot support for sd and emmc.
2. When booting from emmc boot partition, the image_offset is 0. But the flash.bin
generated by mkimage with imximage-8mp-lpddr4.cfg is for sd. It expects to be burn at 32KB offset.
The fit offset 0x60000 has already included the 32KB offset. So when you burn this flash.bin
to emmc boot partition at offset 0, the fit offset should subtract the 32KB (0x60000 - 0x8000).
Signed-off-by: Stefano Babic <sbabic@denx.de>
This displays incorrect data at present due to a missing header file
in display_options. Fix it.
Fixes: 0914011310 ("command: Remove the cmd_tbl_t typedef")
Signed-off-by: Simon Glass <sjg@chromium.org>
Convert the board to DM_ETH instead of legacy networking. This requires
a minor addition to the DT to satisfy the requirement for specifying a
PHY node. No functional change from board user perspective.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
None of these splash screen loading errors are so critical as to
justify complete failure to boot, so just print error message as
needed and return 0, the boot can very likely continue without
the splash.
Fix a couple of missing free(dst) instances as well.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The iMX7D RM 9.2.4.9.3 Power removal flow Table 9-11. Re-enabling power
explicitly says both the DDR controller and the PHY must be reset in the
correct sequence. Currently the code only resets the controller. This
leads to a misbehavior where the system brings the DRAM up after reboot,
but the DRAM is unstable. Add the missing reset.
The easiest way to trigger this is by triggering WDT without having the
WDT assert WDOG_B signal, i.e. mw.w 0x30280000 0x25 .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The u-boot-spl.bin pad with ddr firmware conflicts with the
CONFIG_MALLOC_F_ADDR area, the ddr firmware will be overwritten
by malloc in SPL stage and cause ddr initialization not able
to finish. So update the related addresses to fix the issue.
Reported-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
We no need invoke the code, since spl framework could help
us do that.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Use spl_early_init to replace spl_init, spl_init will be invoked
in board_init_r, we only need use spl_early_init to setup malloc
and scan early dt.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
timer_init has been invoked in arch_cpu_init, no need to invoke
it again in board code.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Drop useless getting ccm device, there is no need to explicted do this
in board code, and we not enable SPL CLK currently.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
When not booting from FlexSPI, the offset computation is:
offset = image_offset + CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR * 512 - 0x8000;
When booting from SD card or eMMC user partition, image_offset is
0x8000. It is useless to add and remove 0x8000.
When booting from other device, image_offset is 0 so this computation is wrong.
Simplfy this computation to work on all booting devices.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Currently watchdog driver is not selected, which causes system to reboot
after staying 60s in the U-Boot prompt.
Fix this problem by enabling CONFIG_WATCHDOG so that watchdog can be
properly serviced.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Currently watchdog driver is not selected, which causes system to reboot
after staying 60s in the U-Boot prompt.
Fix this problem by enabling CONFIG_WATCHDOG so that watchdog can be
properly serviced.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Currently watchdog driver is not selected, which causes system to reboot
after staying 60s in the U-Boot prompt.
Fix this problem by enabling CONFIG_WATCHDOG so that watchdog can be
properly serviced.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Adam Ford <aford173@gmail.com>
Currently watchdog driver is not selected, which causes system to reboot
after staying 60s in the U-Boot prompt.
Fix this problem by enabling CONFIG_WATCHDOG so that watchdog can be
properly serviced.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Currently the watchdog driver is not selected, which causes the following
warnings in both SPL and U-Boot proper:
U-Boot SPL 2020.07-rc1-00387-g67887903af (May 07 2020 - 23:49:27 -0300)
Normal Boot
WDT: Started without servicing (60s timeout)
Trying to boot from MMC1
U-Boot 2020.07-rc1-00387-g67887903af (May 07 2020 - 23:49:27 -0300)
CPU: Freescale i.MX8MMQ rev1.0 at 1200 MHz
Reset cause: POR
Model: FSL i.MX8MM EVK board
DRAM: 2 GiB
WDT: Started without servicing (60s timeout)
....
System reboots after staying 60s in the U-Boot prompt.
Fix this problem by enabling CONFIG_WATCHDOG so that watchdog can be
properly serviced.
Suggested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
With yModem the FIT Image is only supplied once, so we can only
seek forward in the yModem supplied image and never backwards.
With the recent changes to the SPL mechanism, including loading
U-Boot first, FDT after, then the loadables, we must also reorder
the FIT image script to make sure that the loadables are last in
the FIT image.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Tested-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Enable CONFIG_PCI and CONFIG_NVME and related configs for the
Pinebook Pro.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
With the current usb stack in u-boot, all host ports on puma work
flawlessly without any additional special handling, so drop that
usb hub hacking from the puma board.
Tested with mass-storage and usb-ethernet on both usb3 and usb2 ports.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The introduction of the puma-specific generator was mainly a way
to split the pmu firmware from the ATF binary and not having to
distribute that 4GB (sparse) image that was created before moving
to the bl31.elf as base.
Looking at the publically available repository for that separate
pmu firmware
https://git.theobroma-systems.com/rk3399-cortex-m0.git/
there is also no activity for 3 years and apart from some build
customizations no other changes were done.
And even then, if changes need to be made, this can very well also
happen in the atf context itself, so there is no real need to
diverge from the established build procedure and we can just go
back to using the main make_fit_atf.py script.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
So far the puma dts files only just included the main puma dtsi without
handling the actual baseboard and rk3399-puma.dtsi was very much
detached from the variant in the mainline Linux kernel.
Recent changes resulted in a strange situation with nonworking puma boards.
Commit ab800e5a6f ("arm: dts: rockchip: puma: move U-Boot specific bits to u-boot.dtsi")
moved the sdram include from rk3399-puma-ddrX.dts to new files
rk3399-puma-ddrx-u-boot.dtsi which were never included anywhere though.
Commit 167efc2c7a ("arm64: dts: rk3399: Sync v5.7-rc1 from Linux")
replaced the rk3399-puma.dtsi nearly completely, but in the kernel
it definitly depends on a baseboard dts to actually enable peripherals
like sd-slot, uarts, etc.
So to untagle this and bring the whole thing more in line with mainline
Linux, bring the rk3399-puma-haikou.dts over as well, drop the separate
DDR-option devicetrees and instead replace them with a puma Kconfig option
to select and include the needed DDR variant.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Mark the default U-Boot environment as SPI flash since
this is an on board flash device.
Updated env offset, size in contrast with default since
the U-Boot proper has to start from 384K.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
On rockchip platforms, SPI boot image creation is not
straightforward like MMC boot image creation where former
requires to specify tpl, spl in multimage format in mkimage,
and later simply do a concatenate mkimaged-tpl with spl.
On this note, let drop rkspi image type creation via kbuild
and let inform via rockchip.rst
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The 'stdout-path' is missing after dts sync.
Fixes: 167efc2c7a ("arm64: dts: rk3399: Sync v5.7-rc1 from Linux")
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The ROCK-PI-E is a credit card size SBC based on Rockchip RK3328
Quad-Core ARM Cortex A53.
Net - Dual ethernet port, 1 X Gbe, 1 X 100M
USB - USB 3.0
DC - USB-Type C, 5V 2A
Storage - TF card, eMMC
Just build idbloader.img and u-boot.itb for Rockpi E board and
follow the blow steps to replace the relevant partition.
dd if=idbloader.img of=/dev/sdcard seek=64 conv=notrunc
dd if=u-boot.itb of=/dev/sdcard seek=16384 conv=notrunc
Signed-off-by: Banglang Huang <banglang.huang@foxmail.com>
Enable CONFIG_PCI and CONFIG_NVME and related configs for the
ROCKPro64 board.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Pull request for UEFI sub-system for efi-2020-07-rc4 (2)
The following problems are resolved:
* When booting via UEFI an SMBIOS table is presented to the operating
system. If U-Boot tries to add an empty string, this results in corrupted
SMBIOS information. We will now use "Unknown" as property value.
* The EFI_RNG_PROTOCOL uses the DM_RNG drivers. For the virtio RNG driver
the missing DM_RNG Kconfig dependency is added.
* Missing function descriptions for the EFI_SIMPLE_TEXT_OUTPUT_PROTOCOL are
added.
Add the missing Kconfig dependency and let VIRTIO_RNG default to yes.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
smbios_add_string() cannot deal with empty strings. This leads to incorrect
property values and invalid tables. E.g. for the pine64-lts_defconfig
CONFIG_SMBIOS_MANUFACTURER="". Linux command dmidecode shows:
Table 1:
Manufacturer: sunxi
Product Name: sunxi
Table 3:
Invalid entry length (2). DMI table is broken! Stop.
Replace empty strings by "Unknown".
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
- Resync checkpatch.pl (largely) with v5.7 and introduce U-Boot specific
checks in a localized area, so they aren't lost in the future.
- Complete / re-migrate some options from config headers to defconfigs
- Add dependencies to the various debug uart drivers
All of our cmds have a Kconfig entry. Making enabling a CMD via the
config file an error to checkpatch.pl.
Signed-off-by: Tom Rini <trini@konsulko.com>
There is a lot of use of #ifdefs in U-Boot. In an effort reduce this,
suggest using the compile-time construct.
Signed-off-by: Simon Glass <sjg@chromium.org>
A common problem when submitting a new uclass is to forget to add sandbox
tests. Add a warning for this.
Of course tests should always be added for new code, but this one seems to
be missed by nearly every new contributor.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an option to indicate that U-Boot-specific checks should be enabled.
Add a function to house the code that will be added.
Signed-off-by: Simon Glass <sjg@chromium.org>
Keep the U-Boot changes to $logFunctions
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Resync with v5.7 release which changed the default max line
length, update commit to reflect]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_BZIP2
CONFIG_GZIP
CONFIG_LZO
CONFIG_ZLIB
CONFIG_LZMA
CONFIG_LZO
Signed-off-by: Tom Rini <trini@konsulko.com>
Per the boards config header file, there is no useful GPIO on these
boards. Remove CONFIG_CMD_GPIO from the defconfigs.
Cc: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Tom Rini <trini@konsulko.com>
The config header for this platform disables both CMD_SF and CMD_SPI and
the defconfig leaves them enabled. Disable them from the defconfig and
enable them in the header.
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masakazu Mochizuki <masakazu.mochizuki.wd@hitachi.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The common config header for bcm7260 and bcm7445 enable
CONFIG_CMD_EXT2/EXT4 but the defconfigs do not. This results in the
commands being disabled. Enable them via the defconfig.
Cc: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
The config header for this platform uses '#undef' in a number of cases.
All of the MMC related ones were already handled correctly in the
defconfig file. In the case of CONFIG_CMD_FUSE, the command was being
built and enabled via defconfig. Disable it in the defconfig, cleanup
the header.
Reviewed-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Rather than only enable CONFIG_CMD_NAND for non-SPL builds, move the CMD
options to defconfig and rework the guards to not try and call the
function in SPL builds.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Debug console is the part of serial driver in the same file. It means to be
able to enable debug console you also need to enable driver itself.
That's why add all dependecies and list only debug consoles which are
enabled based on driver selection to avoid compilation error when user
asks for certain debug console but driver is not enable for it.
Error:
aarch64-linux-gnu-ld.bfd: common/built-in.o: in function `putc':
/home/monstr/data/disk/u-boot/common/console.c:513: undefined reference to `printch'
aarch64-linux-gnu-ld.bfd: common/built-in.o: in function `puts':
/home/monstr/data/disk/u-boot/common/console.c:563: undefined reference to `printch'
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Fix ns16550 dependency, add ZYNQ_SERIAL, change S5P]
Signed-off-by: Tom Rini <trini@konsulko.com>
When an eTSEC is configured to use TBI, configuration of the
TBI is done through the MIIM registers for that eTSEC.
For example, if a TBI interface is required on eTSEC2, then
the MIIM registers starting at offset 0x2_5520 are used to
configure it.
Fixes: 9a1d6af55e ("net: tsec: Add driver model ethernet support")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The current code accesses eTSEC registers using physical
address directly, it's not correct, though no problem on
current platforms. It won't work on platforms, which does
not support 1:1 virtual-physical address map.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Change the compatible string to "fsl,etsec2" for the Ethernet ports,
which is used in the current driver's match table.
Fixes: 69a00875e3 ("doc: dt-bindings: Describe Freescale TSEC ethernet controller")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Acked-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Introduce the QorIQ DPAA 1 Frame Manager nodes in the T1024RDB
device tree. The device tree fragments are copied over with little
modification from the Linux kernel source code.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the QorIQ DPAA 1 Frame Manager v3 device tree nodes for the
T102x SoCs. The device tree fragments are copied over with little
modification from the Linux kernel source code.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Introduce the QorIQ DPAA 1 Frame Manager nodes in the P5040DS
device tree. The device tree fragments are copied over with little
modification from the Linux kernel source code.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The device tree fragments are copied over with little
modification from the Linux kernel source code.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Introduce the QorIQ DPAA 1 Frame Manager nodes in the P3041DS
device tree. The device tree fragments are copied over with little
modification from the Linux kernel source code.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The device tree fragments are copied over with little
modification from the Linux kernel source code.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Introduce the QorIQ DPAA 1 Frame Manager nodes in the P2041RDB
device tree. The device tree fragments are copied over with little
modification from the Linux kernel source code.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The device tree fragments are copied over with little
modification from the Linux kernel source code.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The device tree fragments are copied over with little
modification from the Linux kernel source code.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the QorIQ DPAA Frame Manager version 3 device tree nodes
description. The device tree fragments are copied over with little
modification from the Linux kernel source code.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the QorIQ DPAA Frame Manager device tree nodes description.
The device tree fragments are copied over with little modification
from the Linux kernel source code.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the QorIQ GPIO device tree nodes description. The device tree
fragments are copied over with little modification from the Linux
kernel source code.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
sbi_probe_extension() is an API defined in SBI v0.2, not v0.1.
Fixes 7e249bc13a: ("riscv: Move all SMP related SBI calls to SBI_v01")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
U-Boot defaults to use SBI v0.2. Howerver there is a global variable
sbi_spec_version that stills refers to v0.1. Since it is not used
anywhere, let's remove it.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
OpenSBI generic platform support provides platform specific
functionality based on the FDT passed by previous booting stage.
Depends on OpenSBI commit:
platform: Add generic FDT based platform support
(sha1: f1aa9e54e00006ae70aeac638d5b75093520f65d)
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
With sifive_fu540_defconfig:
User can use FSBL or u-boot-spl.bin anyone at a time.
For FSBL,
fsbl->fw_payload.bin (opensbi + U-Boot)
For u-boot-spl.bin,
u-boot-spl.bin->FIT image (opensbi + U-Boot proper + dtb)
U-Boot SPL will be loaded by ZSBL from SD card (replace fsbl.bin with
u-boot-spl.bin) and runs in L2 LIM in machine mode and then load FIT
image u-boot.itb from SD card into RAM.
U-Boot SPL expects u-boot.itb FIT image at the starting of SD card sector
number (0x822) of GUID type "2E54B353-1271-4842-806F-E436D6AF6985"
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add U-Boot proper sector start offset for SiFive FU540.
This value is based on the partition layout supported
by SiFive FU540.
u-boot.itb need to write on this specific offset so-that
the SPL will retrieve it from here and load.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
This is a sample GPT partition layout for SD card,
right now three important partitions are added to
make the system bootable.
partition layout:
Part Start LBA End LBA Name
Attributes
Type GUID
Partition GUID
1 0x00000022 0x00000821 "loader1"
attrs: 0x0000000000000000
type: 5b193300-fc78-40cd-8002-e86c45580b47
guid: cbcbef44-e627-42bc-b134-93b6f3784b8c
2 0x00000822 0x00002821 "loader2"
attrs: 0x0000000000000000
type: 2e54b353-1271-4842-806f-e436d6af6985
guid: f54eba28-d8de-4852-978d-1a673777e2ae
3 0x00002822 0x00020821 "rootfs"
attrs: 0x0000000000000004
type: 0fc63daf-8483-4772-8e79-3d69d8477de4
type: linux
guid: 9561df46-8d55-4799-a83b-cfee9ef6ff93
Note:
- loader1 would be fsbl or spl
- loader2 would be U-Boot or U-Boot proper
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
This sync has changes required to use GPIO in U-Boot and
U-Boot SPL.
Sync dts from linux v5.7-rc2 commit:
"riscv: dts: Add GPIO reboot method to HiFive Unleashed DTS file"
(sha1: 0a91330b2af9f71ceeeed483f92774182b58f6d9)
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Set ethernet clock rate to 125 Mhz so that it will work with 1000Mbps,
Earlier this is done by FSBL. With this change We can remove the
ethernet clock rate code from FSBL.
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
U-Boot ethernet works with FSBL flow where releasing ethernet clock
reset is part of FSBL itself but with the SPL, We need to release
ethernet clock reset explicitly for U-Boot proper. With this change
Release ethernet clock reset code in FSBL might not be needed or
unaffected.
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Devicetree files in FU540 platform is synced from Linux, like other
platforms does. Apart from these U-Boot in FU540 would also require
some U-Boot specific node like clint.
So, create board specific -u-boot.dtsi files. This would help of
maintain U-Boot specific changes separately without touching Linux
dts(i) files which indeed easy for syncing from Linux between
releases.
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
When build U-Boot SPL, meet an issue of undefined reference to
'crc7' for drivers/mmc/mmc_spi.c, so let's compile crc7.c when
CONFIG_MMC_SPI selected.
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Pull request for UEFI sub-system for efi-2020-07-rc4
This patch series addresses the following issues:
* allow compiling with clang
* add missing function descriptions to the HTML documentation
* simplify the validation of UEFI images
* validate load options in the UEFI boot manager
In a preparatory patch a structure definition is moved.
- Update various docs to not have 'ARCH=' in them as that's not part of
how U-Boot builds.
- Add macOS tools-only build to Azure to help catch problems on BSD
hosts with tools.
- Bugfixes from the latest header cleanup around ARCH_DMA_MINALIGN
- Assorted small Kconfig logic/typo corrections
- Add a default hash to FIT images that have their its auto generated.
- Other assorted fixes
The global variable, efi_guid_cert_type_pkcs7, will also be used in
efi_image_loader.c in a succeeding patch so as to correctly handle
a signature type of authenticode in signed image.
Meanwhile, it is currently defined in efi_variable.c. Once some secure
storage solution for UEFI variables is introduced, efi_variable.c may
not always be compiled in.
So move the definition to efi_signature.c as a common place.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Knowing that at least one section header follows the optional header we
only need to check for the length of the 64bit header which is longer than
the 32bit header.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
We want to follow the Linux kernel style for function descriptions.
Add missing parentheses after function names.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
On ARM systems gd is stored in register r9 or x18. When compiling with
clang gd is defined as a macro calling function gd_ptr(). So we can not
make assignments to gd.
In the UEFI sub-system we need to save gd when leaving to UEFI binaries and
have to restore gd when reentering U-Boot.
Define a new function set_gd() for setting gd and use it in the UEFI
sub-system.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Tom Rini <trini@konsulko.com>
For passing the optional data of the load option to the loaded imaged
protocol we need its size.
efi_deserialize_load_option() is changed to return the size of the optional
data.
As a by-product we get a partial validation of the load option.
Checking the length of the device path remains to be implemented.
Some Coverity defects identified the load options as user input because
get_unaligned_le32() and get_unaligned_le16() is called. But non of these
Coverity defects can be resolved without marking functions with Coverity
specific tags.
Reported-by: Coverity (CID 303760)
Reported-by: Coverity (CID 303768)
Reported-by: Coverity (CID 303776)
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add the required changes for compiling with DM_ETH on the PPC
DPAA platforms.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
A compilation error appears when QE is compiled with DM_ETH
enabled:
drivers/qe/uec.c: In function 'init_phy':
drivers/qe/uec.c:425:28: error: dereferencing pointer to incomplete type 'struct eth_device'
uec = (uec_private_t *)dev->priv;
^~
drivers/qe/uec.c: In function 'uec_initialize':
drivers/qe/uec.c:1357:43: error: invalid application of 'sizeof' to incomplete type 'struct eth_device'
dev = (struct eth_device *)malloc(sizeof(struct eth_device));
^~~~~~
The patch disables CONFIG_QE when CONFIG_DM_ETH is set.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
P4080DS compilation fails with DM_GPIO enabled:
drivers/gpio/gpio-uclass.c:355:5: error: redefinition of 'gpio_request'
int gpio_request(unsigned gpio, const char *label)
^~~~~~~~~~~~
In file included from ./arch/powerpc/include/asm/arch/gpio.h:17:0,
from ./arch/powerpc/include/asm/gpio.h:1,
from drivers/gpio/gpio-uclass.c:16:
./arch/powerpc/include/asm/mpc85xx_gpio.h:68:19: note: previous definition of 'gpio_request' was here
static inline int gpio_request(unsigned gpio, const char *label)
^~~~~~~~~~~~
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
arch/arm/include/asm/system.h declares psci_arch_init(), but it is
surrounded by #ifdef CONFIG_ARMV8_PSCI.
psci_arch_init() is called for CONFIG_ARMV7_PSCI too. Add the missing
function declaration.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This config option depends on EXT4 support.
If Ext4 write capability is not selected, it generate write error messages
and is unable to maintain boot counter.
Signed-off-by: Frédéric Danis <frederic.danis@collabora.com>
Configuration checks should not be in the C files but in the Kconfig files.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
When building U-Boot we select the architecture via Kconfig and not ARCH
being passed in via the environment or make cmdline.
While in here, add the doc file to the MAINTAINERS entry.
Cc: Amit Singh Tomar <amittomer25@gmail.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Amit Singh Tomar <amittomer25@gmail.com>
When building U-Boot we select the architecture via Kconfig and not ARCH
being passed in via the environment or make cmdline.
While in here, add the doc file to the MAINTAINERS entry.
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Anup Patel <anup.patel@wdc.com>
Cc: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
When building U-Boot we select the architecture via Kconfig and not ARCH
being passed in via the environment or make cmdline.
While in here, add the doc file to the MAINTAINERS entry for coldfire.
Cc: Huan Wang <alison.wang@nxp.com>
Cc: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Tom Rini <trini@konsulko.com>
When building U-Boot we select the architecture via Kconfig and not ARCH
being passed in via the environment or make cmdline.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
When building U-Boot we select the architecture via Kconfig and not ARCH
being passed in via the environment or make cmdline.
Cc: Po Liu <po.liu@nxp.com>
Cc: Qiang Zhao <qiang.zhao@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add building the 'tools-only' target on macOS X 'Catalina'. Hopefully
this will catch changes to host tools that are incompatible on BSD style
environments.
Signed-off-by: Tom Rini <trini@konsulko.com>
This option currently does not add any sort of hash to the images in the
FIT.
Add a hash node requesting a crc32 checksum, which at least provides some
protection.
The crc32 value is easily ignored (e.g. in SPL) if not needed. and takes
up only about 48 bytes per image, including overhead.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Denk <wd@denx.de>
When using CONFIG_ENV_IS_IN_FAT and the config-file specifies a size
larger than what U-Boot wrote into the env-file, a confusing error
message is shown:
$ fw_printenv
Read error on /boot/uboot.env: Success
Fix this by showing a different error message when read returns too
little data.
Signed-off-by: Harald Seiler <hws@denx.de>
This is defined in the asm/cache.h header file. Update this header file to
include it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
This is defined in the asm/cache.h header file. Update this header file to
include it so it gets the same value consistently across U-Boot.
This fixes 'usb host' on omapl138_lcdk.
Fixes: 90526e9fba ("common: Drop net.h from common header")
Reported-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
When building U-Boot we should not blindly use make -j8 but consider the
actual core count given by os.cpu_count().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
- Corrected some FSP-M/FSP-S settings for Chromebook Coral
- ICH SPI driver and mrccache fixes for obtaining the SPI memory map
- Fixed various warnings generated by latest version IASL when compiling
ACPI tables
PCI Firmware specification requires _UID() and doesn't require _ADR()
to be set. Replace latter by former. This fixes the following warning
reported by ACPICA 20200430:
Warning 3073 - Multiple types (Device object requires either a _HID
or _ADR, but not both)
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
PCI Firmware specification requires _UID() and doesn't require _ADR()
to be set. Replace latter by former. This fixes the following warning
reported by ACPICA 20200430:
Warning 3073 - Multiple types (Device object requires either a _HID
or _ADR, but not both)
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Create buffers outside of the methods as ACPICA 20200430 complains
about this:
Remark 2173 - Creation of named objects within a method is highly
inefficient, use globals or method local variables instead
(\_SB.PCI0.LPCB.IURT._CRS)
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
ACPICA complains that either _HID() or _ADR() should be used.
For General Purpose DMA we may not drop the _ADR() because
the device is enumerated by PCI. Thus, simple drop _HID().
Reported-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Create buffers outside of the methods as ACPICA 20200214 complains about this:
Remark 2173 - Creation of named objects within a method is
highly inefficient, use globals or method local variables
instead
Reported-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
This allows the use of the Dediprog em100pro so I can test SPI flash on
this board in my lab.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When comparing hex dumps it is useful to see the offsets of the registers.
Add them in where they correspond to a multiple of 16.
Possibly it would be useful to have a a command to output the FSP values
in human-readable form, making use of the fsp_bindings implementation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some settings were modified slightly in the device-tree conversion. Return
these to their original values. This includes some audio settings and a
few others that have changed.
Note that we still rely on the FSP defaults for most values, so there is
no need to specify a value if the FSP default is suitable.
This makes WiFi work again.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
When comparing hex dumps it is useful to see the offsets of the registers.
Add them in where they correspond to a multiple of 16.
Possibly it would be useful to have a a command to output the FSP values
in human-readable form, making use of the fsp_bindings implementation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some settings were modified slightly in the device-tree conversion. Return
these to their original values.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
The change to avoid searching the device tree does not work on boards
wich don't have driver model set up this early, for example minnowmax.
Put back the old code (converted to livetree) as a fallback for these
devices. Also update the documentation.
This is tested on minnowmax, link, samus and coral.
Fixes: 87f1084a63 (x86: Adjust mrccache_get_region() to use livetree)
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com> (on Intel minnowmax)
The error code is often useful to figure out what is going on. Printing it
does not increase code size much, so print out the error and then hang.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present this logic does not work on link and samus, since their SPI
controller is not a PCI device, but a child of the PCH.
Unfortunately, fixing this involves a lot of extra logic. Still, this was
requested in the review of the fix-up patch, so here it is.
Fixes: 92842147c3 ("spi: ich: Add support for get_mmap() method")
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com> (on Intel minnowmax)
At present the PCI BDF (bus/device/function) is needed to access the SPI
mapping, since the registers are at BAR0. This doesn't work when PCI
auto-config has not been done yet, since BARs are unassigned.
Add another way to find the mapping, using the MMIO base, if the caller
knows this.
Also add a missing function comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Now that the EMAC driver supports the H6 SoC, we can enable the Ethernet
hardware on the Pine H64 board.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The H6 EMAC is very similar to the H3 variant, except that it uses the
same pinmux as R40. Add support for it.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
While the R40 uses a different register for EMAC clock configuration
than other chips, the register has a very similar layout. Reuse the
existing bitfield definitions in this file, since they match.
This allows the driver to compile on the H6 platform, where the
CCM_GMAC_CTRL definitions are not present.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
When compiling with CONFIG_SPL_SERIAL=n, gcc warns about
mbus_configure_port not being marked as static:
In file included from include/common.h:34,
from arch/arm/mach-sunxi/dram_sunxi_dw.c:11:
include/log.h:185:4: warning: 'printf' is static but used in inline function 'mbus_configure_port' which is not static
185 | printf(pr_fmt(fmt), ##args); \
| ^~~~~~
include/log.h:192:2: note: in expansion of macro 'debug_cond'
192 | debug_cond(_DEBUG, fmt, ##args)
| ^~~~~~~~~~
arch/arm/mach-sunxi/dram_sunxi_dw.c:100:2: note: in expansion of macro 'debug'
100 | debug("MBUS port %d cfg0 %08x cfg1 %08x\n", port, cfg0, cfg1);
| ^~~~~
Fix this by updating the function accordingly.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
dm_spi_slave_platdata used in sf_probe for printing
plat->cs value and there is no relevant usage apart
from this.
We have enough debug messages available in SPI and SF
areas so drop this plat get and associated bug statement.
Cc: Simon Glass <sjg@chromium.org>
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
env_flash is a global flash pointer, and the probe would
happen only if env_flash is NULL, but there is no checking
and free the pointer if is not NULL.
So, this patch frees the old env_flash, and get the probed
flash in to env_flash pointer and finally check if is not NULL.
Cc: Simon Glass <sjg@chromium.org>
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The new pointer points to flash found and that would
assign it to global 'flash' pointer for further flash
operations and also keep track of old flash pointer.
This would happen if the probe is successful or even
failed, but current code assigning new into flash before
and after checking the new.
So, drop the assignment after new checks so flash always
latest new pointer even if probe failed or succeed.
Cc: Simon Glass <sjg@chromium.org>
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Currently spi-nor code is assigning _write ops for SST
and other flashes separately.
Just call the sst_write from generic write ops and return
if SST flash found, this way it avoids the confusion of
multiple write ops assignment during the scan and makes
it more feasible for code readability.
No functionality changes.
Cc: Simon Glass <sjg@chromium.org>
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The get_sw_write_prot API is used to get the write-protected
bits of flash by reading the status register and other wards
it's API for reading register bits.
1) This kind of requirement can be achieved using existing
flash operations and flash locking API calls instead of
making a separate flash API.
2) Technically there is no real hardware user for this API to
use in the source tree.
3) Having a flash operations API for simple register read bits
also make difficult to extend the flash operations.
4) Instead of touching generic code, it is possible to have
this functionality inside spinor operations in the form of
flash hooks or fixups for associated flash chips.
Considering all these points, this patch drops the get_sw_write_prot
and associated code bases.
Cc: Simon Glass <sjg@chromium.org>
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
CF_SPI kconfig option defined twice with DM_SPI
and non DM_SPI.
Drop the non DM_SPI side kconfig definition.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
- Fix mmc of path after syncfrom kernel dts;
- Add dwc3 host support with DM for rk3399;
- Add usb2phy and typec phy for rockchip platform;
- Migrate board list doc to rockchip.rst;
- Add rk3399 Pinebook Pro board support;
- Update dram_init in board_init and add memory node in SPL;
In a loading chain SPL -> ATF (->OP-TEE) -> U-Boot, ATF and a subsequent
OP-TEE will re-use the same fdt as the U-Boot target and may need the
information about usable memory ranges.
Especially OP-TEE needs this to initialize dynamic shared memory
(the only type U-Boot implements when talking to OP-TEE).
So allow spl_fixup_fdt() to take a fdt_blob argument, falling back to
the existing CONFIG_SYS_SPL_ARGS_ADDR if needed and call it from the
ATF path as well.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Parts of later SPL may need RAM information as well, so do full
dram_init() call, which includes the existing dram probing but also
initializes the ram information in gd.
dram_init() from sdram.c does the following steps:
- uclass_get_device(UCLASS_RAM, ...) like the current code
- ret = ram_get_info(dev, &ram);
- gd->ram_size = ram.size;
CONFIG_SPL_RAM already makes sure that sdram.c gets compiled
and thus no other variant of dram_init() can exist.
So it's the same functionality as before and only adds that the
SPL now aquires knowledge about the amount of available ram,
which it didn't know about before.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
With the new RPi4 which has 8 GB of RAM, we can have up to four DRAM
banks. Bump up the configuration files to detect all the memory in
U-Boot.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
i2c changes for v2020.07-rc4
- fix eeprom issue with AT24MAC402 (address != 0)
- fix in i2c-uclass.c when compiling compiling with -Wtype-limits
- designware_i2c: small fixes:
- check if the device is powered
- tidy up use of NULL priv
This patch adds or modifies functional tests for the Cover-changes,
Commit-changes, and Series-process-log tags in order to account for new
behavior added in the previous few patches. The '(no changes since v1)'
case is not tested for, since that would need an additional commit to test
in addition to testing the existing code paths.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds support to multi-line changes. That is, if one has a line
in a changelog like
- Do a thing but
it spans multiple lines
Using Series-process-log sort would sort as if those lines were unrelated.
With this patch, any change line starting with whitespace will be
considered part of the change before it.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
By default patman generates a combined changelog for the cover letter. This
may not always be desirable.
Many patches may have the same changes. These can be coalesced with
"Series-process-log: uniq", but this is imperfect. Similar changes like
"Move foo to patch 7" will not be merged with the similar "Move foo to this
patch from patch 6".
Changes may not make sense outside of the patch they are written for. For
example, a change line of "Add check for bar" does not make sense outside
of the context in which bar might be checked for. Some changes like "New"
or "Lint" may be repeated many times throughout different change logs, but
carry no useful information in a summary.
Lastly, I like to summarize the broad strokes of the changes I have made in
the cover letter, while documenting all the details in the appropriate
patches. I think this makes it easier to get a good feel for what has
changed, without making it difficult to wade through every change in the
whole series.
This patch adds two new tags to add changelog entries which only appear in
the cover letter, or only appear in the commit. Changes documented with
"Commit-changes" will only appear in the commit, and will not appear in the
cover letter. Changes documented with "Cover-changes" will not appear in
any commit, and will only appear in the cover letter.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Patman outputs a line for every edition of the series in every patch,
regardless of whether any changes were made. This can result in many
redundant lines in patch changelogs, especially when a patch did not exist
before a certain revision. For example, the existing behaviour could result
in a changelog of
Changes in v7: None
Changes in v6: None
Changes in v5:
- Make a change
Changes in v4: None
Changes in v3:
- New
Changes in v2: None
With this patch applied and with --no-empty-changes, the same patch would
look like
(no changes since v5)
Changes in v5:
- Make a change
Changes in v3:
- New
This is entirely aesthetic, but I think it reduces clutter, especially for
patches added later on in a series.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some mailing lists have size limits and when we add binary contents
to our patches it's easy to exceed the size limits.
Git supports a command line option "--no-binary" to generate patches
without any binary contents. Add an option in patman to handle this.
Note with this option patches cannot be applied properly, but they
are still useful for code review.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Sort the existing command line options by:
- help comes first
- option starts with '-'
- option starts with '--'
Lower case followed by upper case letters, in alphabetical order.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Including the assembler headers before including common.h etc leads to
compilation errors upon MIPS64 based platforms using OF_LIVE. This
patch reorders the include files to the "correct" oder.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since the commit 1289e96797 ("sandbox: spi: Drop command-line SPI
option"), "--spi_sf" command line option is no longer supported.
So update the following documents to sync them up with the change.
doc/arch/sandbox.rst
doc/SPI/README.sandbox-spi
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable USB3.0 Host support for ROC-RK3399-PC boards.
Tested USB3.0 SSD on Type C1 port on board.
=> usb start
starting USB...
Bus usb@fe380000: USB EHCI 1.00
Bus usb@fe3c0000: USB EHCI 1.00
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fe380000 for devices... 1 USB Device(s) found
scanning bus usb@fe3c0000 for devices... 2 USB Device(s) found
scanning bus dwc3 for devices... 6 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
=> usb tree
USB device tree:
1 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller
1 Hub (480 Mb/s, 0mA)
| u-boot EHCI Host Controller
|
+-2 Hub (480 Mb/s, 100mA)
USB 2.0 Hub [MTT]
1 Hub (5 Gb/s, 0mA)
| U-Boot XHCI Host Controller
|
+-2 Hub (480 Mb/s, 0mA)
| | VIA Labs, Inc. USB2.0 Hub
| |
| +-4 Hub (480 Mb/s, 100mA)
| | USB 2.0 Hub
| |
| +-5 (480 Mb/s, 100mA)
| VIA Technologies Inc. USB 2.0 BILLBOARD 0000000000000001
|
+-3 Hub (5 Gb/s, 0mA)
| VIA Labs, Inc. USB3.0 Hub
|
+-6 Mass Storage (5 Gb/s, 224mA)
JMicron External Disk 3.0 DB12345678A2
=> usb reset
resetting USB...
Bus usb@fe380000: USB EHCI 1.00
Bus usb@fe3c0000: USB EHCI 1.00
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fe380000 for devices... 1 USB Device(s) found
scanning bus usb@fe3c0000 for devices... 2 USB Device(s) found
scanning bus dwc3 for devices... 6 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
RK3399 Type-C PHY is required that must hold whole USB3.0 OTG controller
in resetting to hold pipe power state in P2 before initializing the PHY.
This commit fixed it and added device compatible for rockchip platform.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Print the error code if the regulator enable fails, otherwise the error
message is rather useless and confusing.
Signed-off-by: Marek Vasut <marex@denx.de>
The board_eth_init() is not used for DM case, enable it only for
the non-DM case. This function should eventually be removed.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The regulator-fixed would return -ENOSYS when enabled/disabled,
because this operation is not supported, but this is not an error
e.g. on systems where the VBUS cannot be controlled, so if this
is the error code reported by the regulator core, consider it a
success and continue.
Signed-off-by: Marek Vasut <marex@denx.de>
Although I think it never occurs, the code doesn't make sense, because
it may allow to assign an IN endpoint to ss->ep_out.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
By default when core sees any transaction error (CRC or overflow) it
replies with terminating retry ACK (Retry=1 and Nump == 0).
Enabling this Auto Retry feature in controller will make the core send
a non-terminanting ACK upon such transaction errors. That is, ACK TP
with Retry=1 and Nump != 0.
Doing so will give controller a chance to recover from transient error
conditions.
Reference from below Linux commit,
commit <b138e23d3dff> ("usb: dwc3: core: Enable AutoRetry feature
in the controller")
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This patch adds a quirk to disable USB 2.0 MAC linestate check
during HS transmit. Refer the dwc3 databook, we can use it for
some special platforms if the linestate not reflect the expected
line state(J) during transmission.
When use this quirk, the controller implements a fixed 40-bit
TxEndDelay after the packet is given on UTMI and ignores the
linestate during the transmit of a token (during token-to-token
and token-to-data IPGAP).
On some rockchip platforms (e.g. rk3399), it requires to disable
the u2mac linestate check to decrease the SSPLIT token to SETUP
token inter-packet delay from 566ns to 466ns, and fix the issue
that FS/LS devices not recognized if inserted through USB 3.0 HUB.
Reference from below Linux commit,
commit <65db7a0c9816> ("usb: dwc3: add disable u2mac linestate
check quirk")
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a quirk to clear the GUSB2PHYCFG.U2_FREECLK_EXISTS bit,
which specifies whether the USB2.0 PHY provides a free-running
PHY clock, which is active when the clock control input is active.
Refer to commit 27f83eeb6b42("usb: dwc3: add dis_u2_freeclk_exists_quirk")
in Linux Rockchip Kernel.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Add a quirk to clear the GUSB2PHYCFG.ENBLSLPM bit, which controls
whether the PHY receives the suspend signal from the controller.
Refer to commit ec791d149bca("usb: dwc3: Add dis_enblslpm_quirk")
in Linux Kernel.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Add USB TYPEC PHY driver for rockchip platform.
Referenced from Linux TypeC PHY driver, currently
supporting usb3-port and dp-port need to add it
in the future.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add Rockchip USB2PHY driver with initial support.
This will help to use it for EHCI controller in host
mode, and USB 3.0 controller in otg mode.
More functionality like charge, vbus detection will
add it in future changes.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Due to v5.7-rc1 sync the SD controller nodes in rk3399.dtsi
have SCLK_UPHY0_TCPDCORE, SCLK_UPHY1_TCPDCORE assigned-clocks
which are usually required for Linux and don't require to
handle them in U-Boot.
assigned-clocks = <&cru SCLK_UPHY0_TCPDCORE>;
assigned-clocks = <&cru SCLK_UPHY1_TCPDCORE>;
So, mark them as empty in clock otherwise device probe on
those typec phy driver would fail.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable/Disable the USB2PHY clk for rk3399.
CLK is clear in enable and set in disable functionality.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
As documentation is being moved to doc/boards/rockchip create a warning
message and remove the redundant list of supported boards.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
As an additional step to move documentation to doc/boards/rockchip
improve format of the supported board list to make it more readable.
Additionally, add the configuration files used to build them based on
doc/README.rockchip.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
U-Boot has video output enabled so time to get keyboard working.
=> usb reset;usb tree
resetting USB...
Bus usb@fe380000: USB EHCI 1.00
Bus usb@fe3a0000: USB OHCI 1.0
Bus usb@fe3c0000: USB EHCI 1.00
Bus usb@fe3e0000: USB OHCI 1.0
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fe380000 for devices... 1 USB Device(s) found
scanning bus usb@fe3a0000 for devices... 1 USB Device(s) found
scanning bus usb@fe3c0000 for devices... 1 USB Device(s) found
scanning bus usb@fe3e0000 for devices... 3 USB Device(s) found
scanning bus dwc3 for devices... cannot reset port 1!?
2 USB Device(s) found
scanning usb for storage devices... 2 Storage Device(s) found
USB device tree:
1 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller
1 Hub (12 Mb/s, 0mA)
U-Boot Root Hub
1 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller
1 Hub (12 Mb/s, 0mA)
| U-Boot Root Hub
|
+-2 Hub (12 Mb/s, 100mA)
| ALCOR Generic USB Hub
|
+-3 Mass Storage (12 Mb/s, 200mA)
Kingston DT 101 G2 001478544887BB3157380157
1 Hub (5 Gb/s, 0mA)
| U-Boot XHCI Host Controller
|
+-2 Mass Storage (5 Gb/s, 76mA)
ADATA ADATA USB Flash Drive 1520405012240002
Signed-off-by: Marcin Juszkiewicz <marcin@juszkiewicz.com.pl>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The vpcie*-supply properties are optional and these are absent on
boards like the ROCKPro64 and Firefly RK3399 where the voltage is
supplied by always-on regulators that are already enabled upon
boot. Make these regulators optional and properly check their
presence before attempting to enable them.
Makes PCIe work on un U-Boot on the boards mentioned above.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Marcin Juszkiewicz <marcin@juszkiewicz.com.pl>
Linux v5.7-rc1 dts(i) sync has changed the sdmmc node from
dwmmc@fe320000 to mmc@fe320000 and this ofpath is being
used in rockchip spl bootdevice code.
So, update the ofpath with a new node name and prefix "same-as-spl"
to missing u-boot,spl-boot-order.
Bug log:
U-Boot SPL 2020.07-rc2-00256-g9c5fef5774 (May 24 2020 - 20:20:43 +0530)
Trying to boot from MMC2
mmc_load_image_raw_sector: mmc block read error
Trying to boot from MMC1
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
Fixes: 167efc2c7a ("arm64: dts: rk3399: Sync v5.7-rc1 from Linux"
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The khadas-vim, khadas-vim2, libretech-ac & libretech-*-pc boards were missing
DT tweak to enable USB gadget.
Add them to their -u-boot.dtsi files and include the right gxl-u-boot.dtsi.
Fixes: a19e8a0f03 ("arm: dts: meson-gxl: Add USB Gadget nodes for U-Boot")
Reported-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Include the common g12 u-boot tweaks to permit enabling video output tweaks
on Khadas VIM3 boards.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The I2C2 uses different pinmux on AV96, use correct pinmux and
also add comments about the I2C being present on the "low-speed"
expansion connector X6.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Because of this commit :
5ae84860b0 ("misc: i2c_eeprom: verify that the chip is functional at probe()")
at probe time, each eeprom is tested for read at offset 0.
The Atmel AT24MAC402 eeprom has different mapping. One i2c slave address is
used for the lower 0x80 bytes and another i2c slave address is used for the
upper 0x80 bytes. Because of this basically the i2c master sees 2 different
slaves. We need the upper bytes because we read the unique MAC address from
this EEPROM area.
However this implies that our slave address will return error on reads
from address 0x0 to 0x80.
To solve this, implemented an offset field inside platform data that is by
default 0 (as it is used now), but can be changed in the compatible table.
The probe function will now read at this offset and use it, instead of blindly
checking offset 0.
This will fix the regression noticed on these EEPROMs since the commit
abovementioned that introduces the probe failed issue.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
When compiling with -Wtype-limits we see this error:
drivers/i2c/i2c-uclass.c: In function ‘i2c_deblock_gpio_loop’:
drivers/i2c/i2c-uclass.c:517:21: error: comparison of
unsigned expression >= 0 is always true [-Werror=type-limits]
517 | while (scl_count-- >= 0) {
|
Don't loop forever.
Fixes: 1f746a2c82 ("i2c: Make deblock delay and SCL clock configurable")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
If the device doesn't return a version that means the device is
non-functional.
The dw_i2c_regs had invalid offsets for the version field. I got the
correct value from the DesignWare databook. It also matches what the
Picasso PPR says.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@chromium.org>
Tested on chromebook_coral:
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we still have pre-driver-model code in this driver and it makes
things a bit confusing. In particular calc_bus_speed() is called with priv
as NULL if not using driver model.
This results in spk_cnt and comp_param1 being read from an invalid address
if not using driver model. For comp_param1 this may not cause problems if
reading from addresses close to 0 happens to be allowed, as high speed is
only supported by DM code. But spk_cnt is subsequently used to calculate
the bus periods and so this may cause problems (e.g. on spear600 board
which has not been migrated yet).
Add a new parameter regs parameter to calc_bus_speed() and add more
comments to this function and to _dw_i2c_set_bus_speed(), which calls it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
- Use device tree for FSP-M and FSP-S configuration on Intel Apollo Lake
- Add SMBIOS cbmem entry parsing for coreboot
- Various clean-ups to CBFS implementation
The size is not actually used since it is present in the header. Drop this
parameter. Also tidy up error handling while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Currently we support reading a file from CBFS given the address of the end
of the ROM. Sometimes we only know the start of the CBFS. Add a function
to find a file given that.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This function currently returns a node pointer so there is no way to know
the error code. Also it uses data in BSS which seems unnecessary since the
caller might prefer to use a local variable.
Update the function and split its body out into a separate function so we
can use it later.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We may as well return the error code and use it directly in the command
code. CBFS still uses its own error enum which we may be able to remove,
but leave it for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The start address of the CBFS is used when scanning for files. It makes
sense to put this in our cbfs_priv struct and calculate it when we read
the header.
Update the code accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It doesn't make sense to use u8 * as the pointer type for accessing the
CBFS since we do not access it as bytes, but via structures. Change it to
void *, which allows us to avoid a cast.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
These two functions have mostly the same code. Pull this out into a common
function.
Also make this function zero the private data so that callers don't have
to do it. Finally, update cbfs_load_header_ptr() to take the base of the
ROM as its parameter, which makes more sense than passing the address of
the header within the ROM.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This function is strange at the moment in that it takes a header pointer
but then accesses the cbfs_s global. Currently clients have their own priv
pointer, so update the function to take that as a parameter instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This function is strange at the moment in that it takes a header pointer
but then accesses the cbfs_s global. Currently clients have their own priv
pointer, so update the function to take that as a parameter instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present this uses a true return to indicate it found a file. Adjust it
to use 0 for this, so it is consistent with other functions.
Update its callers accordingly and add a check for malloc() failure in
file_cbfs_fill_cache().
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present this uses an int type. U-Boot now supports bool so use this
instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
U-Boot uses ulong for addresses but there are a few places in this driver
that don't use it. Convert this driver over to follow this convention
fully.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present the result variable in the cbfs_priv is called 'result' as is
the local variable in a few functions. Change the latter to 'ret' which is
more common in U-Boot and avoids confusion.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
A the moment the FSP-M configuration is a mix of hard coded values and
devicetree properties.
This patch makes FSP-M full configurable from devicetree by adding
binding properties for all FSP-M parameters.
Co-developed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> (Tested on coral)
[sjg: Fix a build error for coral]
Signed-off-by: Simon Glass <sjg@chromium.org>
[bmeng: Add __maybe_unused to fsp_update_config_from_dtb()]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
We don't need to print this information since it is shown when the MTRRs
are displayed. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Convert the CRS305-1G-4S board to CRS3xx-98DX3236 to enable easier
implementation of new CRS3xx series boards, based on Marvell Prestera
98DX3236.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Commit f49ac7e1c4 switched the default PHY speed to 3.125Gbit to resolve
issues with SFP modules. However, U-Boot does not have a "2500base-x"
phy-mode.
Resolve this by using "sgmii-2500" instead.
Signed-off-by: Jakov Petrina <jakov.petrina@sartura.hr>
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Stefan Roese <sr@denx.de>
Without CONFIG_SYS_U_BOOT_OFFS set to CONFIG_SYS_SPI_U_BOOT_OFFS, U-Boot
will be located at address 0x16000. But, SPL will try to load the
payload from 0x24000 causing the boot to hang.
Signed-off-by: Ezra Buehler <ezra@easyb.ch>
Reviewed-by: Stefan Roese <sr@denx.de>
Without this U-Boot-specific property, booting on the Synology DS414
(or DS214+) fails in SPL. The spi0 DT node is not scanned, as a result
the SPI flash cannot be found.
Signed-off-by: Ezra Buehler <ezra@easyb.ch>
Reviewed-by: Stefan Roese <sr@denx.de>
SMP support for S-mode U-Boot is enabled only if SBI_V01 is enabled.
There is no point in supporting SMP related (IPI and fences) SBI calls
when SBI_V02 is enabled.
Modify all the SMP related SBI calls to be defined only for SBI_V01.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
- Enable DM_ETH on omap3_logic board
- Enable Caches in SPL for K3 platforms
- Enable backup boot mode support for J721E
- Update the DDR timings for AM654 EVM
- Add automated tests for RX-51
- A few minor Kconfig migrations / corrections
- DFU doc fixes/improvements
- Bugfix for ARMv8, env userspace building, more NULL checks in generic
PHY code
CONFIG_BZIP2 and CONFIG_GZIP_COMPRESSED are Kconfig options. Select them
by CONFIG_SANDBOX instead of setting them in configs/sandbox.h.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix the following warning:
cmd/zip.c: In function ‘do_zip’:
cmd/zip.c:30:6: warning: implicit declaration of function ‘gzip’; did you mean ‘do_zip’? [-Wimplicit-function-declaration]
if (gzip((void *) dst, &dst_len, (void *) src, src_len) != 0)
^~~~
do_zip
Include gzip.h header which declares the gzip() function.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move the CONFIG_GZIP_COMPRESSED from a config.h macro to a Kconfig menu
item. It is not selectable by a user because there is no reason to do
so. Instead it will be automatically selected by the stuff which uses
gzip(), like the zip command.
Remove it from the config_whitelist.txt. Also remove
CONFIG_GZIP_COMPRESS_DEF_SZ as this was never used on any board. The
default seems to be sane, otherwise it should be added as a Kconfig
option.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
unzip calls gzwrite() which is provided in lib/gunzip.c. Make sure it is
automatically pulled in if the user selects CMD_UNZIP.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Heinrich Schuchardt <xypron.glkp@gmx.de>
As reported by Nicolas Carrier on the Buildroot mailing list [1],
there is a new build issue while building a program which interacts with
the u-boot environment. This program uses the headers of the ubootenv
library provided by uboot-tools.
This is a recent change from uboot [2] adding "#include <env.h>" to
fw_env.h. Adding env.h require a board configuration to build since
it also include compiler.h (and others uboot internal includes).
env.h include seems not needed since env_set() is not used in fw_env tool.
Nicolas removed env.h from fw_env tool and fixed it's build issue.
This problem is present since uboot v2019.10.
[1] http://lists.busybox.net/pipermail/buildroot/2020-April/280307.html
[2] 9fb625ce05
Reported-by: Nicolas Carrier <nicolas.carrier@orolia.com>
Signed-off-by: Romain Naour <romain.naour@gmail.com>
It is possible that users of generic_phy_*() APIs may pass a valid
struct phy pointer but phy->dev can be NULL, leading to NULL pointer
deference in phy_dev_ops().
So call generic_phy_valid() to verify that phy and phy->dev are both
valid.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
include/dfu.h and doc/api/dfu.rst belong to the device firmware update
sub-system. So let's add them to DFU in MAINTAINERS.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Lukasz Majewski <lukma@denx.de>
Add the device firmware update functions to the generated HTML
documentation.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Lukasz Majewski <lukma@denx.de>
In dfu_alt_info for eMMC the eMMC partition number can be specified.
The separator in dfu_alt_info is a semicolon not a comma.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Lukasz Majewski <lukma@denx.de>
The documentation should rest with the same maintainer as the code.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The enum dcache_optoion contains a shift left 2 bits in the armv8 case
already. The PMD_ATTRINDX(option) macro will perform a left shift of 2
bits. Perform a right shift so that in the end we get the correct
value.
[trini: Reword the commit message]
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Instead of reading out the entire FIFO and possibly overwriting U-Boot
memory, read out one packet per recv call, pass it to U-Boot network
stack, and repeat. It is however necessary to cache RXFC value, because
reading that one out clears it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Split network handling functions into non-DM specific parts and
common code in preparation for conversion to DM.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Introduce a private data structure for this driver with embedded
struct eth_device and pass it around. This prepares the driver to
work with both DM and non-DM systems.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
There is only one chip ID in the table of chip IDs for this chip.
Read out the chip ID instead and mask off the last "revision" bit
to check the chip ID, this works for all chips in the family. Then
drop the chip ID passing around.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The packet status and length information should be extracted from the
FIFO per-packet. Adjust the code such that it reads the packet meta
data and then the packet afterward, if applicable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Per KS8851-16MLL, the RXQCR is a 16bit register. Use 16bit accessors
to it consistently and drop the ks_wrreg8() function altogether, as
it is not used anymore.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The cached RXQCR value is never updated, remove the cache and just use
the bits in the cache directly in the code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Replace combination of malloc()+memset() with calloc() as the behavior
is exactly the same and the amount of code is reduced. Moreover, remove
printf() in the fail path, as it is useless, and return proper -ENOMEM
return code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Pull request for UEFI sub-system for efi-2020-07-rc3 (2)
Problems fixed with these patches are:
* UEFI sub-system not working with virtio block devices
* Missing SATA support in UEFI sub-system
* A superfluous debug statement
UniPhier SoC updates for v2020.07
- De-assert write protect for Denali NAND driver
- Clean up include directives
- Migrate to DM_ETH, and remove legacy board_eth_init()
The phy_bulk pointer *usb_phys is used before allocated,
fix it by using a phy_bulk variable instead in
xhci_dwc3_platdata struct
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
The omap3.dtsi file shows the usbhshost node with two sub-nodes
for ohci and ehci. This patch file creates the usbhshost, and
pulls the portX-mode information. It then locates the EHCI
sub-node, and initializes the EHCI controller with the info
pulled from the usbhshost node.
There is still more to do since there isn't an actual link
between the 'phys' reference and the corresponding phy driver,
and there is no nop-xceiv driver yet.
In the meantime, the older style reference to
CONFIG_OMAP_EHCI_PHYx_RESET_GPIO is still needed to pull
the phy out of reset until the phy driver is completed and the
phandle reference is made.
Signed-off-by: Adam Ford <aford173@gmail.com>
Use the same approach as ROC-RK3328-CC which enables SPL GPIO,
pinctl and regulator support. This allows the gen3 board to
boot through SPL and does not break gen2 in the process.
Signed-off-by: Kurt Miller <kurt@intricatesoftware.com>
Acked-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Veyrons do not need full pinctrl support for SPL.
The full pinctrl support does nothing when enabled with OF_PLATDATA,
thus was already unused.
This frees about 4kB of SPL size.
Signed-off-by: Urja Rannikko <urjaman@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
gd->fdt_blob is null if using OF_PLATDATA in SPL, which causes a hang
after f0921f5098 ("fdt: Sync up to the latest libfdt").
We use the same test that is used in spl_common_init on whether to call
fdtdec_setup to unconditionally avoid linking in the fdt-using code
when not necessary and thus reduce SPL size.
Signed-off-by: Urja Rannikko <urjaman@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Previously veyron_init() was called in board_init() context, which is
called after relocation. Moving it to veyron.c used board_early_init_f
which is called way earlier, and causes veyron_init to hang.
Using board_early_init_r instead fixes this.
Fixes: b678f2790c ("rockchip: rk3288: Move veyron_init() back to veyron.c")
Signed-off-by: Urja Rannikko <urjaman@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Apparently speedy was forgotten from this list of veyron devices.
Fixes: 49105fb7ed ("rockchip: add common spl board file")
Signed-off-by: Urja Rannikko <urjaman@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Building with -Wtype-limits yields
tools/rkcommon.c: In function ‘rkcommon_check_params’:
tools/rkcommon.c:158:27: warning: comparison of
unsigned expression < 0 is always false [-Wtype-limits]
158 | if (spl_params.init_size < 0)
| ^
tools/rkcommon.c:165:28: warning: comparison of
unsigned expression < 0 is always false [-Wtype-limits]
165 | if (spl_params.boot_size < 0)
|
Fix the value checks.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Yes, it is possible to have a dedicated UCLASS PHY driver
for this Rockchip PCIe PHY but there are some issues on
Generic PHY framework to support the same.
The Generic PHY framework is unable to get the PHY if
the PHY parent is of a different uclass.
Say if we try to get the PCIe PHY then the phy-uclass
will look for PHY in the first instance if it is not
in the root node it will try to probe the parent by
assuming that the actual PHY is inside the parent PHY
of UCLASS_PHY. But, in rk3399 hardware representation
PHY like emmc, usb and pcie are part of syscon which
is completely a different of UCLASS_SYSCON.
Example:
grf: syscon@ff770000 {
compatible = "rockchip,rk3399-grf", "syscon", "simple-mfd";
reg = <0x0 0xff770000 0x0 0x10000>;
#address-cells = <1>;
#size-cells = <1>;
pcie_phy: pcie-phy {
compatible = "rockchip,rk3399-pcie-phy";
clocks = <&cru SCLK_PCIEPHY_REF>;
clock-names = "refclk";
#phy-cells = <1>;
resets = <&cru SRST_PCIEPHY>;
drive-impedance-ohm = <50>;
reset-names = "phy";
status = "disabled";
};
};
Due to this limitation, this patch adds a separate PHY
driver for Rockchip PCIe. This might be removed in future
once Generic PHY supports this limitation.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Suniel Mahesh <sunil@amarulasolutions.com> #roc-rk3399-pc
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Yes, most of the high speed peripheral clocks
in rk3399 enabled by default.
But it would be better to handle them via clk
enable/disable API for handling proper reset
conditions like 'usb reset' over command line.
So, enable USB, GMAC clock via enable/disable ops.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Suniel Mahesh <sunil.m@amarulasolutions.com> # roc-rk3399-pc
Tested-by: Suniel Mahesh <sunil@amarulasolutions.com> #roc-rk3399-pc
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Should initialization of pdata values have failed for some reason,
we end up in endless loop when getting the CPU temperature value
and can not boot. Check alert value in pdata and only retry reading
temperature if alert value is not zero. Also shorten the temperature
info string.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This fixes getting DT alert and critical pdata values in imx_scu_thermal
driver. On i.MX8QXP using not initialized alert pdata value resulted in
boot hang and endless loop outputting:
CPU Temperature (47200C) has beyond alert (0C), close to critical (0C) waiting...
While at it, preset CPU type values once to avoid multiple calls
of device_is_compatible() for same property.
Fixes: 3ee6ea443e ("cpu: imx_cpu: Print the CPU temperature for iMX8QM A72")
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
CPU type and rate detection is broken, for A35 cpu we get A53:
...
sc_pm_get_clock_rate: resource:0 clk:2: res:3
Could not read CPU frequency: -22
CPU: NXP i.MX8QXP RevB A53 at 0 MHz at 47C
Fixes: 55bc96f3b6 ("cpu: imx8: fix get core name and rate")
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
adapting commit fa2047c473 ("rockchip: rk3328: enable spl-fifo-mode
for emmc and sdmmc") for rk3399.
Since mmc to sram can't do dma, add patch to prevent aborts transferring
TF-A parts.
Signed-off-by: Deepak Das <deepakdas.linux@gmail.com>
The make_fit_spl scripts get the dtb to use as commandline option,
so use it for puma as well.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
This platform completely migrated to CONFIG_DM_ETH.
board_eth_init() is only called from net/eth_legacy.c
Remove the legacy hook.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
<common.h> pulls in a lot of bloat. <common.h> is unneeded in most of
places.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
I do not understand the changes made to these files by
commit f7ae49fc4f ("common: Drop log.h from common header").
git show f7ae49fc4f -- arch/arm/mach-uniphier/
None of them uses the log function feature.
Simply revert the changes made to these files.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
I do not understand the change made to this file by
commit 691d719db7 ("common: Drop init.h from common header").
git show 691d719db7 -- arch/arm/mach-uniphier/dram/umc-pxs2.c
This file does not call or define any functions declared in <init.h>
Simply revert the change made to this file.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
I do not understand the changes made to this file by
commit 90526e9fba ("common: Drop net.h from common header").
git show 90526e9fba -- arch/arm/mach-uniphier/micro-support-card.c
The necessary declaration is already included by <netdev.h> at line 112.
It also moved the <dm/of.h> inclusion, but I do not understand the
motivation of doing so, either.
Simply revert the changes made to this file.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
I do not understand the change made to this file by
commit 90526e9fba ("common: Drop net.h from common header").
git show 90526e9fba -- arch/arm/mach-uniphier/arm32/psci.c
It added <asm/cache.h> while this file does not call the standard cache
functions at all.
All the uniphier-specific cache functions, uniphier_cache_*() are
declared in cache-uniphier.h, which is already included from this file.
Including <asm/system.h> is sensible to fix the -Wmissing-prototypes
warnings because this file defines psci_cpu_on and psci_system_reset().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[ Linux commit 9afbe7c0140f663586edb6e823b616bd7076c00a ]
If the write protect signal from this IP is connected to the NAND
device, this IP can handle the WP# pin via the WRITE_PROTECT
register.
The Denali NAND Flash Memory Controller User's Guide describes
this register like follows:
When the controller is in reset, the WP# pin is always asserted
to the device. Once the reset is removed, the WP# is de-asserted.
The software will then have to come and program this bit to
assert/de-assert the same.
1 - Write protect de-assert
0 - Write protect assert
The default value is 1, so the write protect is de-asserted after
the reset is removed. The driver can write to the device unless
someone has explicitly cleared register before booting the kernel.
The boot ROM of some UniPhier SoCs (LD4, Pro4, sLD8, Pro5) is the
case; the boot ROM clears the WRITE_PROTECT register when the system
is booting from the NAND device, so the NAND device becomes read-only.
Set it to 1 in the driver in order to allow the write access to the
device.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
drivers/net/smc911x.c has been converted to DM.
select DM_ETH to enable it for all the UniPhier platform boards.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This CONFIG option is only used in denali_spl.c
Move it close to SPL_NAND_DENALI, and make it depend on SPL_NAND_DENALI.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Prior to corrective patches for virtio and SATA devices the same device
path was installed on two different handles. This is not allowable.
With this patch we will throw an error if this condition occurs for
block devices.
Update a comment for the installation of the simple file system
protocol.
Reported-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Provide device path nodes for SATA devices.
This avoids creation of two handles with the same device path indicating
our root node.
This is what the device paths for a SATA drive with four partitions could
like:
/VenHw(..)/Sata(0x0,0xffff,0x0)
/VenHw(..)/Sata(0x0,0xffff,0x0)/HD(1,MBR,0x81ea591f,0x800,0x63ff830)
/VenHw(..)/Sata(0x0,0xffff,0x0)/HD(2,MBR,0x81ea591f,0x6400800,0x9ff830)
/VenHw(..)/Sata(0x0,0xffff,0x0)/HD(3,MBR,0x81ea591f,0x6e00800,0x16ef2ab0)
/VenHw(..)/Sata(0x0,0xffff,0x0)/HD(4,MBR,0x81ea591f,0x1dcf3800,0x1dcedab0)
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The UEFI specification does not define a device sub-type for virtio.
Let's use a vendor hardware node here.
This avoids creation of two handles with the same device path indicating
our root node.
Reported-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
With commit 16ad946f41 ("efi_loader: change setup sequence") the
detection of block device was moved to the start of the initialization
sequence. In the case of virtio devices two handles with the same device
path being created.
The root node handle should be created before anything else.
Reported-by: Ard Biesheuvel <ardb@kernel.org>
Fixes: 16ad946f41 ("efi_loader: change setup sequence")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The UEFI 2.8 specification has introduced the EFI_MEMORY_SP memory
attribute. Add it to the 'efidebug memmap' and 'efi mem' commands.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Remove unnecessary debug() from efi_set_variable_common().
native_name is NULL, so there is no meaning to print it.
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
- Add DM_ETH support for lx2160aqds, ls2080aqds, ls1088aqds
- QSI related fixes on ls1012a, ls2080a, ls1046a, ls1088a, ls1043a based
platforms
- Bug-fixes/updtaes related to ls1046afrwy, fsl-mc, msi-map property
Enable these two options to let compiler eliminate unused code.
On R2Dplus, this results in considerable amount of saved space:
text data bss dec hex filename
- 266580 13196 39076 318852 4dd84 u-boot
+ 220214 12797 38745 271756 4258c u-boot
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Tom Rini <trini@konsulko.com>
Enable DDR52 modes, since the SD core supports correct switching now.
For completeness, list HS200 modes, however those were already enabled.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The prior-stage firmware generates DT fragment containing the /firmware
node, /reserved-memory node and /memory@ nodes. Merge these nodes into
the U-Boot DT, so U-Boot can use this information.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reserve 4 kiB of space in R-Car Gen3 DTs when those DTs are compiled
to permit patching in OpTee-OS /firmware node, /reserved-memory node
and possibly also additional /memory@ nodes.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Add weak function which is called right after fdtdec_setup() configured
the U-Boot DT. This permits board-specific adjustments to the U-Boot DT
before U-Boot starts parsing the DT. This could be used e.g. to patch in
various custom nodes or merge in DT fragments from prior-stage firmware.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
This function is useful to merge a subset of DT into another DT, for
example if some prior-stage firmware passes a DT fragment to U-Boot
and U-Boot needs to merge it into its own DT. Export this function
to permit implementing such functionality.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
This driver is safe to use in SPL without relocation. Denying
DM_FLAG_PRE_RELOC prevents its usability for verifying the main U-Boot
or other artifacts from the SPL unless needless enabling the full driver
set (SPL_OF_PLATDATA).
Fixes: 17e1174085 ("drivers: crypto: rsa_mod_exp: avoid DM_FLAG_PRE_RELOC")
CC: Heinrich Schuchardt <xypron.glpk@gmx.de>
CC: Marek Vasut <marex@denx.de>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
This macro is only used (tested for existence) in mpc83xx.c, which
unconditionally includes mpc83xx.h where it is unconditionally
defined. Removing it makes the remaining code easier to read.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Add support for enabling dcache already in SPL. It accelerates the boot
and resolves the risk to run into unaligned 64-bit accesses.
Based on original patch by Lokesh Vulta.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
This patch contains test/nokia_rx51_test.sh script which automatically
download and compile all needed tools in local temporary directory to
generate a simple MTD images for booting Maemo kernel image by U-Boot from
RAM, eMMC and OneNAND. MTD images are then run in virtual n900 machine
provided by qemu-linaro project.
This script does not need any special privileges, so it can be run as
non-root nobody user.
It can be used to check that U-Boot for Nokia N900 is not broken and can be
successfully booted in emulator.
Script is registered to .azure-pipelines.yml, .gitlab-ci.yml and
.travis.yml so it would be automatically run on those CI services.
Signed-off-by: Pali Rohár <pali@kernel.org>
When the boot of J721E devices using the primary bootmode (configured
via device pins) fails a boot using the configured backup bootmode is
attempted. To take advantage of the backup boot mode feature go ahead
and add support to the J721E init code to determine whether the ROM code
performed the boot using the primary or backup boot mode, and if booted
from the backup boot mode, decode the bootmode settings into the
appropriate U-Boot mode accordingly so that the boot can proceed.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
With the converstion of SMC911x to DM, this can facilitate the omap3
boards from LogicPD (now called Beacon EmbeddedWorks) to be converted.
There isn't a clean solution to doing this in phases, so the boards are
all being done together to avoid breaking functionality.
Because the GPMC bus hasn't been converted, the -u-boot.dtsi node needs
to show the address of the ethernet controller for each board.
The board file, which is common betwen the OMAP35 and DM37 SOM LV and
Torpedo boards, can remove the manual ethernet initialization, but it
still needs to register the address and GPMC configuration for the Ethernet
controller which is now being moved around to board_late_init().
Lastly, this patch updates the various config files to add the reference
for DM_ETH and remove the SMC address, which is now fetched from the
newly created device tree nodes.
Signed-off-by: Adam Ford <aford173@gmail.com>
EMIF tool for AM65x [1] is now updated from rev 1.98 to 2.02
This update includes
* Optimizations in IO configuration.
* Fix for byte enablement in GCR registers.
* Fixes for PG2.0 including ZQ control.
[1]: http://www.ti.com/lit/zip/sprcah7
Acked-by: James Doublesin <doublesin@ti.com>
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Enable CONFIG_DM_ETH and CONFIG_DM_MDIO and related configs for the
LS2080AQDS board.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add support for selecting the appropriate DTS file depending on the
SERDES protocol used.
The fsl-ls2080a-qds DTS will be used by default if there isn't a DTS
file specifically made for the current SERDES protocol.
This patch adds the necessary DPMAC nodes (DPMAC 1-8) for
protocol 42 (0x2A) on SD#1.
Also, in case CONFIG_DM_ETH and CONFIG_MULTI_DTB_FIT are enabled
implement the board_fit_config_name_match() function in order to choose
the appropriate DTS.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In case CONFIG_DM_ETH is enabled, no hardcoding is necessary for DPAA2
Ethernet devices. Compile out any unnecessary setup when CONFIG_DM_ETH
is activated. Also, force the PCI devices to be enumerated at probe
time.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable CONFIG_DM_ETH and CONFIG_DM_MDIO and related configs for the
LS1088AQDS board.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In case CONFIG_DM_ETH is enabled, no hardcoding is necessary for DPAA2
Ethernet devices. Compile out any unnecessary setup when CONFIG_DM_ETH
is activated. Also, force the PCI devices to be enumerated at probe
time.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add support for selecting the appropriate DTS file depending on the
SERDES protocol used. The fsl-ls2088a-qds DTS will be used by default if
there isn't a DTS file specifically made for the current SERDES
protocol.
This patch adds support for the on-board ports (DPMAC 1,2 and 4,5) found
on the SERDES protocols 21(0x15) and 29(0x1d) for SD#1.
On the LS1088AQDS board EMDIO1 is used with two onboard RGMII PHYs
(Realtek RTL8211FD-CG), as well as 2 input/output connectors for
mezzanine cards. Configuration signals from the Qixis FPGA control the
routing of the external MDIOs.
Register 0x54 of the Qixis FPGA controls the routing of the EMDIO1 one
of the 2 IO slots. As a consequence, a new node is added to
describe register 0x54 as a MDIO mux controlled with child nodes
describing all the IO slots as MDIO buses.
Also, in case CONFIG_DM_ETH and CONFIG_MULTI_DTB_FIT are enabled
implement the board_fit_config_name_match() function in order to choose
the appropriate DTS.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
ls1046afrwy does not support sata boot.
So Override default BOOT_TARGET_DEVICES
and support only mmc, usb and dhcp as boot targets.
Signed-off-by: Pramod Kumar <pramod.kumar_1@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The DPC fixup for MAC address and enet_if is not made if
/board/ports node is missing in DPC file.
Add /board/ports or /ports nodes if them are missing.
Signed-off-by: Razvan Ionut Cirjan <razvanionut.cirjan@nxp.com>
Reviewed-by: Ioana Ciornei <Ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
CONFIG_MTD_NOR_FLASH flag needs to be enable for all
boot sources,as all flash drivers need to compile in
TFA Boot.Probe ifc nor flash only when there is nor
flash available on board.So needs to detect ifc-nor
flash at run-time for probing.
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In case CONFIG_DM_ETH and CONFIG_MULTI_DTB_FIT are enabled implement the
board_fit_config_name_match() function in order to choose the
appropriate DTS for the current SERDES protocol configuration.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Razvan Ionut Cirjan <razvanionut.cirjan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In case CONFIG_DM_ETH is enabled, no hardcoding is necessary for DPAA2
Ethernet devices. Compile out any unnecessary setup when CONFIG_DM_ETH
is activated. Also, force the PCI devices to be enumerated at probe
time.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Razvan Ionut Cirjan <razvanionut.cirjan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add device trees describing possible uses of mezzanine cards depending
on the SERDES protocol employed.
This patch adds DPAA2 networking support for the following protocols on
each SERDES block:
* SD #1: 3, 7, 19, 20
* SD #2: 11
Each SERDES block has a different device tree file per protocol
supported, where the IO SLOTs used are enabled and PHYs located on the
mezzanine cards are described. Also, dpmac nodes are edited and their
associated phy-connection-type and phy-handle are added.
Top DTS files are also added for each combination of protocol on the 3
SERDES blocks.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Razvan Ionut Cirjan <razvanionut.cirjan@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The LX2160A processor has two external MDIO interfaces, described in the
DTS as emdio1 and emdio2.
On the LX2160AQDS board EMDIO1 is used with two onboard RGMII PHYs
(Realtek RTL8211FD-CG), as well as eight input/output connectors for
mezzanine cards. Configuration signals from the Qixis FPGA control the
routing of the external MDIOs.
Register 0x54 of the Qixis FPGA controls the routing of the EMDIO1 one
of the 8 IO slots. As a consequence, a new node is added to
describe register 0x54 as a MDIO mux controlled with child nodes
describing all the IO slots as MDIO buses.
Also, DPMAC 17 and 18 are updated to reference the on-board PHYs.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Razvan Ionut Cirjan <razvanionut.cirjan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add nodes for DPMACs 1, 2 and 5-6 which were missing from the
description. These will be later used on the LX2160AQDS specific DTS.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Razvan Ionut Cirjan <razvanionut.cirjan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Similarly to iommu-map, the msi-map property must also be fixed up
in the device tree, in order for the icid -> streamid translation
be possible in the MSI case as well.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Diana Craciun <diana.craciun@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Bus callback functions for read/write/reset need to be set only for
DM_ETH, moving endif a bit lower.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Commit 323d3af59f ("configs: ls1012ardb: Enable
CONFIG_SYS_RELOC_GD_ENV_ADDR") enables the config only for LS1012ARDB.
Apart from LS1012A-RDB, other platforms such as LS1012A-FRWY, LS2088A
and LS1046A-RDB/FRWY also require this config to be enabled. This also
helps in resolving booting crash observed in flash environment.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
All LS1012A board variants have same CONFIG_ENV_SECT_SIZE and
CONFIG_ENV_SIZE values. If both config values are same, flash
environment cannot be saved. Since, CONFIG_ENV_SECT_SIZE needs to be
same as that of flash sector size, this entry cannot be changed.
Reduce CONFIG_ENV_SIZE value to 0x2000. This also helps in making config
value aligned with other boards environemt size.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.kumar@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
CONFIG_SYS_MALLOC_LEN is currently set to low value and leaves very less
space to do malloc in flash environmet. Increase the value to get more
memory and also make it align with other boards(ls1046a, ls1043a etc.)
config values.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
BOOT command currently access spi-nor flash memory directly. As per spi-mem
framework, flash memory access via absolute addresses is no more possible.
Use flash APIs to access memory instead of directly using it.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
MC_INIT command currently access spi-nor flash memory directly. As per
spi-mem framework, flash memory access via absolute addresses is no more
possible. Use flash APIs to access memory instead of directly using it.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
CONFIG_ENV_ADDR helps in picking environment from flash before DDR init.
The macro value is already defined in ls1046ardb_tfa_defconfig, also
define the value as 0x40300000 in qspi_defconfig.
ls1046aqds has one spansion flash "S25FL128S_64K" of size 16M with
sector size 64K. Correct ENV_ADDR and ENV_SECT_SIZE value for QSPI and
TFA defconfigs of the board.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
CONFIG_ENV_ADDR helps in picking environment from flash before DDR init.
QSPI region in LS2088ARDB and LS2088AQDS starts from 0x20000000 offset.
Correct the config value i.e 0x80500000 -> 0x20500000.
Also, define config value as 0x20300000 in qspi defconfig.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
CONFIG_ENV_ADDR helps in picking environment from flash before DDR init.
QSPI region starts from 0x20000000 offset.
Correct the config value i.e 0x80500000 -> 0x20500000.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
According to new qspi driver, some properties like "bus-num, num-cs,
big-endian" are no longer used. Device endiannes can be determined from
device-type data in driver.
Now use board specific compatibles, generic node names and specific
labels to align with linux device-tree properties.
Also consolidate spi-max-frequency to 50Mhz treewide.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable CONFIG_SPI_FLASH_SPANSION in defconfigs of LS1046ARDB and
LS1046AQDS which have two spansion flases i.e s25fs512s each of size
64M.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Since CONFIG_FSL_QSPI is already enabled for LS1012A in defconfigs. Also
enable CONFIG_SPI_FLASH_SPANSION for LS1012A boards having spansion
flashes.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Move CONFIG_FSL_QSPI to the board defconfigs and while at it also move
CONFIG_SPI_FLASH_SPANSION for LS1043AQDS.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Some of these options are not used by the driver anymore and some of
them are obsolete as the information is gathered from the dt. Also
consolidating defines in common headers.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Some places use __ASSEMBLER__ instead which does not work since the
Makefile does not define it. Fix them.
Signed-off-by: Simon Glass <sjg@chromium.org>
We should not use typedefs in U-Boot. They cannot be used as forward
declarations which means that header files must include the full header to
access them.
Drop the typedef and rename the struct to remove the _s suffix which is
now not useful.
This requires quite a few header-file additions.
Signed-off-by: Simon Glass <sjg@chromium.org>
We should not be using typedefs and these make it harder to use
forward declarations (to reduce header file inclusions). Drop the typedef.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.
Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is bad practice to include common.h in other header files since it can
bring in any number of superfluous definitions. It implies that some C
files don't include it and thus may be missing CONFIG options that are set
up by that file. The C files should include these themselves.
Update some header files in arch/arm to drop this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this uncommon header out of the common header.
Fix up some style problems in flash.h while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Pull request for UEFI sub-system for efi-2020-07-rc3
A series of patches introduces the possibility to manage UEFI variables
via an OP-TEE module. CONFIG_EFI_MM_COMM_TEE enables this. If this
option is not specified the U-Boot behavior remains unchanged. A defconfig
is provided for compile testing (lx2160ardb_tfa_stmm_defconfig).
An incorrect UEFI memory allocation for fsl-layerscape is fixed
A defconfig is added on lx2160ardb which allows UEFI variable management
via OP-TEE. Enable the the node in the relevant DTS file.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Previous patches allow UEFI secure variables to be stored in an RPMB
device using OPTEE. Add a config for the lx2160a hardware so the feature
gets at least compiled.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Remove superfluous differences to lx2160ardb_tfa_defconfig.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
If OP-TEE is compiled with an EDK2 application running in secure world
it can process and store UEFI variables in an RPMB.
Add documentation for the config options enabling this.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add myself as maintainer for the OP-TEE related UEFI variable storage.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
With the previous patches that use OP-TEE and StandAloneMM for UEFI
variable storage we've added functionality for efi_query_variable_info.
So let's add the relevant command to efidebug and retrieve information
about the container used to store UEFI variables
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
In OP-TEE we can run EDK2's StandAloneMM on a secure partition.
StandAloneMM is responsible for the UEFI variable support. In
combination with OP-TEE and it's U-Boot supplicant, variables are
authenticated/validated in secure world and stored on an RPMB partition.
So let's add a new config option in U-Boot implementing the necessary
calls to OP-TEE for the variable management.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Pipat Methavanitpong <pipat1010@gmail.com>
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
In Arm devices OP-TEE has the ability to run StandAloneMM (from EDK2)
in a separate partition and handle UEFI variables.
A following patch introduces this functionality.
Add the headers needed for OP-TEE <--> StandAloneMM communication
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Virtually all callers of this function do the rounding on their own.
Some do it right, some don't. Instead of doing this in each caller,
do the rounding in efi_add_memory_map(). Change the size parameter
to bytes instead of pages and remove aligning and size calculation in
all callers.
There is no more need to make the original efi_add_memory_map() (which
takes pages as size) available outside the module. Thus rename it to
efi_add_memory_map_pg() and make it static to prevent further misuse
outside the module.
Signed-off-by: Michael Walle <michael@walle.cc>
Add missing comma in sunxi_display.c.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Enable CONFIG_PCI_INIT_R for qemux86 and qemux86-64 pci enumeration during
boot in order to eliminate the custom preboot commands in
include/configs/qemu-x86.h.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
With CONFIG_DM_PCI enabled, PCI buses are not enumerated at boot, as they
are without that config option enabled. However, there are cases such as DM
PCI-based Ethernet devices that need the PCI bus enumerated so that they
can be discovered by their drivers.
Currently, to solve this, some boards enumerate the pci bus using
"pci enum" preboot command, while others do it manually in board files
(in board_init/board_late_init/etc. functions).
In order to possibly make the pci enumeration process uniform across all
boards, introduce CONFIG_PCI_INIT_R Kconfig option.
This change also preserves the current behavior in the !DM_PCI case
(pci_init is run unconditionally at boot).
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Use IS_ENABLED() instead of #ifdef in should_load_env and initr_env
functions.
No functional change intended.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
- A number of symbol name consistency updates
- JFFS2 bugfix
- Use /* fallthrough */ for now to help at least gcc know when we're
intentionally not 'break;'ing in a switch statement, we'll adopt
fallthrough; later on.
- Assorted other fixes
If "object=" is specified in "keydir" when using the pkcs11 engine do
not append another "object=<key-name-hint>". This makes it possible to
use object names other than the key name hint. These two string
identifiers are not necessarily equal.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Bastian Krause <bst@pengutronix.de>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
GCC recognizes /* fallthrough */ if -Wimplicit-fallthrough=3 is enabled.
Let's use it consistently.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
GCC recognizes /* fallthrough */ if -Wimplicit-fallthrough=3 is enabled.
Let's use it consistently.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
CONFIG_SYS_SDRAM_BASE maybe zero. Avoid a build warning when compiling with
-Wtype-limits.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
A large number of boards call preloader_console_init unconditionally.
Currently, they fail to build with CONFIG_SPL_SERIAL=n, because the
function is undefined in that case. To fix the build, always define
preloader_console_init, but make it no-op when CONFIG_SPL_SERIAL=n.
For the few boards that did check for CONFIG_SPL_SERIAL before calling
preloader_console_init, remove the checks, since the function can now
be called unconditionally.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
File 'defconfig' is a build artifact of 'make savedefconfig'.
Remove it when cleaning.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The inode list uses version and ino, the dirent list uses version and pino.
This information is collected during scanning, reducing accesses to flash
and significantly speeding up ls and read.
Signed-off-by: Petr Borsodi <petr.borsodi@i.cz>
Obsolete nodes (ie. without the JFFS2_NODE_ACCURATE flag) were ignored
because they had seemingly invalid crc. This could lead to finding
the phantom node header in obsolete node data.
Signed-off-by: Petr Borsodi <petr.borsodi@i.cz>
Have this symbol follow the pattern of all other such symbols.
This patch also removes a TODO from the code.
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
The SPL linker script had been left in arch/$(ARCH)/cpu/$(CPU)/$(SOC);
therefore move it to the already-established arch/$(ARCH)/mach-$(SOC)
location.
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Have this symbol follow the pattern of all other such symbols.
This patch removes a TODO from the code.
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
The comment immediately above the block of machine directory names implored
users to keep the macro names sorted, but, alas, this is no longer the case.
Put the list of machine directory names back in alphanumerical order by
CONFIG_* macro name, as the comment asks. Sort all the symbols as though they
all followed the convention of having the string "ARCH_" in the middle of
their definitions.
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Following the example of most other SoCs in arch/$(ARCH)/cpu/$(CPU)/$(SOC)
move the lpc32xx code from arch/arm/cpu/arm926ejs/lpc32xx to
arch/arm/mach-lpc32xx.
Following the checklist from
commit 01f1445630 ("ARM: prepare for moving SoC sources into mach-*"):
[1] move files from arch/arm/cpu/arm926ejs/lpc32xx to arch/arm/mach-lpx32xx
[2] add machine entry to arch/arm/Makefile
[3] remove "obj-y += ..." from arch/arm/cpu/arm926ejs/Makefile
[4] fix the Kconfig file path in arch/arm/Kconfig
[5] (no MAINTAINERS update)
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
stdlib.h is the header for malloc since at least c89/c90.
There is no system malloc.h on OpenBSD and trying to use malloc.h here
falls back to the U-Boot malloc.h breaking the build of qemu_arm64.
Fixes: 336d4615f8 ("dm: core: Create a new header file for 'compat' features")
Signed-off-by: Jonathan Gray <jsg@jsg.id.au>
This code dates back to 2006, commit 483a0cf804 ("Fixes for gcc 3.4
based m68k toolchain,").
GCC 3.4 is so old. We do not support it.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
At present the MD5 option cannot be enabled by board configs since it has
no Kconfig name. It is generally enabled, so long as FIT support is
present. But not all boards use FIT, particularly in SPL
Fix this and add an option for SPL as well. This allows board code to call
md5() even if FIT support is not enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
The speed member actually uses an enum, so add this to the comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
This avoids needless rebuilding.
Fixes: 2f57c95100 ("spl: dm: Make it possible for the SPL to pick its own DTB from a FIT")
CC: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
The dts dir must exists when running this rule.
That missing dependency broke e.g. "make -j" for the am65x targets.
Fixes: 2f57c95100 ("spl: dm: Make it possible for the SPL to pick its own DTB from a FIT")
CC: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
- stm32mp1: migrate MTD and DFU configuration in Kconfig
- stm32mp1: add command stm32prog
- stm32mp1: several board and arch updates
- stm32mp1: activate data cache in SPL and before relocation
- Many improvment for AV96 board and DHCOR SoM
(add new defconfig, DDR3 coding on DHCOR SoM, split between board and SOM
Synchronize DDR setttings on DH SoMs, setting for I2C EEPROM)
- clk: stm32mp1: fix CK_MPU calculation
- DT alignment of stm32mp1 device tree with Linux 5.7-rc2
- fix phy configuration for RPi4's bcmgenet
- sync RPi4's env size with other RPi configs
- add kconfig option to reserver more pages in the EFI mem map
- add support for SDMA which is used by RPi4
- fix corner case boot bug for RPi3 32-bit
DT alignment with Linux 5.7-rc2, including the kernel commits
431c89e6f323 ARM: dts: stm32: use correct vqmmc regu for eMMC on stm32mp1 ED1/EV1 boards
79e965053872 ARM: dts: stm32: add disable-wp property for SD-card on STM32MP1 boards
877db62ea516 ARM: dts: stm32: add cd-gpios properties for SD-cards on STM32MP1 boards
7519e95ba5f8 ARM: dts: stm32: Do clean up in stmpic nodes on stm32mp15 boards
f68e2dbc591a ARM: dts: stm32: Rename stmfx joystick pins on stm32mp157c-ev1
d6210da4f8bf ARM: dts: stm32: add cpu clock-frequency property on stm32mp15x
b65b6fc56925 ARM: dts: stm32: add wakeup-source in all I2C nodes of stm32mp157c
1c1cf5996cfb ARM: dts: stm32: add i2c4 sleep pinctrl on stm32mp157c-ed1
bef15fc0fad9 ARM: dts: stm32: add i2c2/i2c5 sleep pinctrl on stm32mp157c-ev1
b7fc0a87b9ac ARM: dts: stm32: add i2c4 sleep pinctrl on stm32mp15xx-dkx
a5e557655285 ARM: dts: stm32: set i2c4 bus freq to 400KHz on stm32mp15 DK boards
8bc631b650a6 ARM: dts: stm32: set i2c4 bus freq to 400KHz on stm32mp157c-ed1
fccd6a577bb3 ARM: dts: stm32: Correct stmfx node name on stm32mp157c-ev1 board
cc775a83db65 ARM: dts: stm32: add resets property on all DMA nodes on stm32mp151
c5fae093511b ARM: dts: stm32: enable USB OTG Dual Role on stm32mp157c-ev1
9879e2165758 ARM: dts: stm32: add USB OTG pinctrl to stm32mp15
82ac8a81f985 ARM: dts: stm32: add USB OTG full support on stm32mp151
8714b26e2863 ARM: dts: stm32: remove useless properties in stm32mp157a-avenger96 stmpic node
a7959919709e ARM: dts: stm32: Add UART8 pins A pinmux entry on stm32mp1
4d7c53a684da ARM: dts: stm32: Add USART3 pins A pinmux entry on stm32mp1
80ab128332ee ARM: dts: stm32: Add SAI2A pins B pinmux entry on stm32mp1
ab7f98c0c546 ARM: dts: stm32: Add Ethernet0 RMII pins A pinmux entry on stm32mp1
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
When the CK_MPU used PLL1_MPUDIV, the current rate is
wrong. The clock must use stm32mp1_mpu_div as a shift
value. Fix the check value used to enter PLL_MPUDIV.
Signed-off-by: Lionel Debieve <lionel.debieve@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Change the mmc displayed name in U-Boot for stm32_sdmmc2 driver to
“STM32 SD/MMC”.
This stm32_sdmmc2 driver is for version 2 of the ST HW IP SDMMC but the
displayed name "STM32 SDMMC2" is confusing for user, between the
instance of SDMMC and the device identifier of MMC.
For example on EV1 board, we have:
STM32MP1> mmc list
STM32 SDMMC2: 0 (SD)
STM32 SDMMC2: 1 (eMMC)
Changed to more clear:
STM32MP1> mmc list
STM32 SD/MMC: 0 (SD)
STM32 SD/MMC: 1 (eMMC)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Activate cache on DDR to improve the accesses to DDR used by SPL:
- CONFIG_SPL_BSS_START_ADDR
- CONFIG_SYS_SPL_MALLOC_START
Cache is configured only when DDR is fully initialized,
to avoid speculative access and issue in get_ram_size().
Data cache is deactivated at the end of SPL, to flush the data cache
and the TLB.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Activate the data cache in SPL and in U-Boot before relocation.
In arch_cpu_init(), the function early_enable_caches() sets the early
TLB, early_tlb[] located .init section, and set cacheable:
- for SPL, all the SYSRAM
- for U-Boot, all the DDR
After relocation, the function enable_caches() (called by board_r)
reconfigures the MMU with new TLB location (reserved in
board_f.c::reserve_mmu) and re-enable the data cache.
This patch allows to reduce the execution time, particularly
- for the device tree parsing in U-Boot pre-reloc stage
(dm_extended_scan_fd =>dm_scan_fdt)
- in I2C timing computation in SPL (stm32_i2c_choose_solution())
For example, the result on STM32MP157C-DK2 board is:
1,6s gain for trusted boot chain with TF-A
2,2s gain for basic boot chain with SPL
For information, as TLB is added in .data section, the binary size
increased and the SPL load time by ROM code increased (30ms on DK2).
But early malloc can't be used for TLB because arch_cpu_init()
is executed before the early poll initialization done in spl_common_init()
called by spl_early_init() So it too late for this use case.
And if I initialize the MMU and the cache after this function it is
too late, as dm_init_and_scan and fdt parsing is also called in
spl_common_init().
And .BSS can be used in board_init_f(): only stack and global can use
before BSS init done in board_init_r().
So .data is the better solution without hardcoded location but if you
have size issue for SPL you can deactivate cache for SPL only
(with CONFIG_SPL_SYS_DCACHE_OFF).
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Define I2C EEPROM bus and address, so that the 'eeprom' command uses
the correct ones and does not generate the following error:
eeprom_rw_block: Cannot find udev for a bus 0
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Add custom DDR DRAM settings for the DHCOR and DHCOM SoMs and put them
into use by the board file instead of the default ones. These new DRAM
settings are a better fit for the SoMs.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
The commit 132e5b6898 ("ARM: dts: stm32: Split AV96 into DHCOR SoM
and AV96 board") was not applied correctly and in full, and omitted
an important split of the SoM into 3V3 and 1V8 options. The Avenger96
board is based on the 1V8 IO option of the DHCOR SoM, however this is
an optional modification of the 3V3 IO DHCOR SoM with extra on-SoM
regulator to cater for the 96boards 1V8 IO requirements.
Reinstate the split between the 1V8 and 3V3 IO variants.
Fixes: 132e5b6898 ("ARM: dts: stm32: Split AV96 into DHCOR SoM and AV96 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
On DK1/2 board, when a 1.5A power supply is detected, a warning
message is displayed. In this message, "1.5mA" is displayed instead
of "1.5A".
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Need Realtek driver to manage in RTL8211F the configuration of the LED.
Initialize LCR (LED Control Register) to configure green LED for Link,
yellow LED for Active
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Use the DDR3 dtsi files generated by STM32CubeMX 5.6.0
Speed Bin Grade = using DDR3-1066G / 8-8-8 and all others
parameters at default value.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
The GPIO support is needed in SPL to managed the SD cart detect
used on stm32mp157c-ev1 and dk2 board.
So this patch activates the associated code in stm32_gpio.c.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This patch avoids infinite loop when I/O compensation failed,
it adds a 1s timeout to detect error.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
It is not allowed to change the user setting of bootdelay, so
remove the check of the boot-source to disable it dynamically
in board_late_init()
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
For booting Linux in the generic distro mechanism and support of
FDTDIR in extlinux.conf , cmd/pxe.c retrieves the FDT file name
from "fdtfile" environment variable.
Dynamically build this variable with compatible of STMicroelectronics
boards.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Software workaround for I2C issue on EV1 board,
configure the IRQ line for touchscreen before LCD reset
to fix the used I2C address.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Force boot-led ON and no more rely on default-state.
This patch avoid device-tree modification for U-Boot.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Since commit commit dd2810851e ("stm32mp1: board: support of
error led on ed1/ev1 board") the attended behavior was no more
respected in case of low power source detection on DK2.
The expected behavior is either the error LED keeps blinking for ever,
or blinks 2 or 3 times and must stay ON.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Call hang when an error is detected for probe of any driver
needed for console or DDR init: clk, reset and pincontrol
NB: previous behavior with a return in board_init_f() was not correct;
DDR is not initialized and SPL execution can't continue
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This command is not more depending on fuse command, but have
direct access to BSEC misc driver, so the dependency with
can be removed CMD_FUSE
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add support of RAM target in flashlayout to load kernel image
("system") and device tree ("filesystem") in DDR with DFU and
start these images.
The flashlayout.tsv is:
- 0x01 fsbl Binary none 0x00000000 tf-a.stm32
- 0x03 ssbl Binary none 0x00000000 u-boot.stm32
P 0x10 kernel System ram0 0xC2000000 uImage.bin
P 0x11 dtb FileSystem ram0 0xC4000000 dtb.bin
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Support an U-Boot script included in uimage instead of flashlayout file
(text file in tsv format).
This feature is used to execute this script directly when U-Boot is
loaded in DDR (for update without STM32CubeProgrammer for example).
A simple example with dfu-util only is:
$> echo "dfu 0" > script.cmd
$> mkimage -C none -A arm -T script -d script.cmd script.uimg
$> mkimage -T stm32image -a 0xC0000000 -e 0xC0000000 -d script.uimg \
script.stm32
$> dfu-util -d 0483:df11 -a 1 -D tf-a.stm32
$> dfu-util -d 0483:df11 -a 0 -D script.stm32
$> dfu-util -d 0483:df11 -a 0 -D u-boot.stm32
$> dfu-util -d 0483:df11 -a 0 -e
Then you can used dfu-utils to update your device
To increase speed, you can also switch to fastboot protocol with:
echo "fastboot 0" > script.cmd
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Enable the videoconsole during the stm32prog command execution
to have information without UART.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add a support of UART, using the same protocol than MCU STM32.
See "AN5275: USB DFU/USART protocols used in STM32MP1 Series
bootloaders" for details.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add a virtual partition to update the pmic non volatile memory.
(on ST board, STPMIC1).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add a virtual partition to update the STM32MP15x OTP based
on SMC service provided by TF-A.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add support for delete option 'D' in flashlayout for
full device or for partitions
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
For reliability of boot from NAND/SPI-NAND (with read-disturb issue)
the SSBL can be present several time, when it is indicated in the
flashlayout with "Binary(X)".
The received binary is copied X times by U-Boot on the target.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Dynamically adapt the MTD partitions in NOR/NAND/SPI-NAND when stm32prog
command detects in the parsed flash layout files:
- a fsbl partition in NOR.
- a tee partition in NOR/NAND/SPI-NAND
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add support of MTD device (DFU_MTD backend) for
NOR, NAND or SPI-NAND target.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add support of partial update, update only some partitions,
and check the coherence of the layout with the existing GPT
partitions (offset and size).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add support of eMMC device boot partition with
part_id = -1 for offset="boot1"
or = -2 for offset="boot2"
The stm32prog command configures the MMC DFU backend with "mmcpart"
and configure the eMMC (command "mmc bootbus" and "mmc partconf")
when the update is done.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add support of MMC device (based on DFU_MMC backend)
for SD card and eMMC update.
Create a GPT partitioning on the device.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add a specific command stm32prog for STM32MP soc family
witch allows to program the boot devices with the tool
STM32CubeProgrammer (http://www.st.com/STM32CubeProg).
This command uses the same UART STM32 protocol than MCU
STM32 with or USB with DFU protocol v1.1 (ithe MCU ST
extension are no supported).
The executed actions are based on a tab separated value file
with a stm32 header, the FlashLayout file
(https://wiki.st.com/stm32mpu/wiki/STM32CubeProgrammer_flashlayout).
This file is parsed by the U-Boot command to:
- initialize the devices
- create the partition table on each device
- initialize the DFU backend to access to not volatile memory
(NOR/NAND/SD/eMMC) or to virtual device (OTP/PMIC)
Up to STM32PROG_MAX_DEV (5) devices can be updated with a FlashLayout.
The communication between U-Boot and STM32CubeProgrammer is done with
the specific alternate configuration (see "AN5275: USB DFU/USART protocols
used in STM32MP1 Series bootloaders" for details).
The command stm32prog is executed when a boot from USB is detected
(selected with bootpins) and we can program the boot devices with
a simple command (on Windows or Linux):
PC $> STM32_Programmer_CLI -c port=usb1 -w flaslayout.tsv
1/ the ROM code loads TF-A in embedded RAM (DFU or uart)
2/ TF-A loads flashlayout file and U-Boot in DDR (DFU or uart)
3/ U-Boot executes the stm32prog command (DFU or uart)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add a function get_cpu_dev to get the DEV_ID present
in DBGMCU_IDC register.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add prototype for function dfu_transaction_initiate and
dfu_transaction_cleanup to avoid warning with W=1.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add a function g_dnl_set_product to change the Product string used in USB
enumeration in any command based on download gadget.
If the function is called with NULL pointer, the product string is set to
the default value (product[] = "USB download gadget").
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Update stm32mp1 board documentation with new management of MMC and
MTD partitions and new PID df11.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Dynamically adapt the MTD partitions in NAND and SPI-NAND when boot from
NOR or NAND/SPI-NAND is detected.
This patch avoids to define the save MTD partition name for NOR and NAND
devices and issue with latest kernel: only the needed MTD partitions
are defined.
For boot from NOR
1/ bootloader (TF-A, U-Boot and OP-TE) in NOR
2/ one large UBI partition in NAND
For boot from NAND
1/ bootloader (TF-A, U-Boot and OP-TE) in MTD raw partition
2/ one large UBI partition
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Manage BOOT_FLASH_SPINAND, with boot_device="spi-nand"
and treat this value in bootcmd_stm32mp.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
As the op-tee presence is detected by U-boot, the stm32mp15_optee_defconfig
is identical to stm32mp15_trusted_defconfig and can be removed.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Save and use the FDT address provided by TF-A in r2 at boot time
(it is NT_FW_CONFIG = Non Trusted Firmware configuration file)
Address is saved in save_boot_params(), called by start.S
and the used DTB is gd->fdt_blob = board_fdt_blob_setup().
If dtb is not provided or invalid, U-Boot use as fallback
the builtin DTB.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Activate OP-TEE driver for trusted and optee defconfig.
This driver allows detection of TEE presence for boot from flash;
CONFIG_STM32MP1_OPTEE is also removed.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add reserve memory for OP-TEE in U-Boot and in kernel device tree:
- no more reduce the DDR size in "memory" node:
CONFIG_SYS_MEM_TOP_HIDE is no more used
- U-Boot device-tree defines the needed "reserved-memory" for OP-TEE
and U-Boot should not use this reserved memory: board_get_usable_ram_top
use lmb lib to found the first free region, the not reserved
memory, enough to relocate U-Boot: the needed size of U-Boot
is estimated with gd->mon_len + CONFIG_SYS_MALLOC_LEN.
- the optee node ("optee@...": firmware with compatible "linaro,optee-tz")
and the associated "reserved-memory" are deactivated in kernel device
tree when OP-TEE is not detected by U-Boot to prevent kernel issue
(memory is reserved but not used, optee driver probe failed).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This patch reduces the stm32mp1 environment size and builds
dynamically the MTD partitions with information from defconfig
(CONFIG_MTDPARTS_...).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This patch reduces the stm32mp1 environment size and
builds dynamically the DFU board configuration with gpt
and mtd partitions and information from defconfig
(CONFIG_DFU_ALT_RAM0).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Move the stm32mp1 common code set_dfu_alt_info() in common directory,
this patch reduce the maintenance effort on this generic part (not board
dependent).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Move the stm32mp1 common code board_get_mtdparts() in common directory,
this patch reduce the maintenance effort on this generic part (not board
dependent).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
The DHCOR board does exist in multiple variants with different DDR3
DRAM sizes. To cater for all of them, implement DDR3 code handling.
There are two GPIOs which code the DRAM size populated on the SoM,
read them out and use the value to pick the correct DDR3 config.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Adjust the DDR configuration dtsi such that they only generate the
DRAM configuration node, the DDR controller node is moved into the
stm32mp157-u-boot.dtsi itself. This permits including multiple DDR
configuration dtsi files in board DT.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Add support for multiple DRAM configuration subnodes, while retaining
the support for a single flat DRAM configuration node. This is useful
on systems which can be manufactured in multiple configurations and
where the DRAM configuration can be determined at runtime.
The code is augmented by a function which can be overridden on board
level, allowing a match on the configuration node name, very much like
the fitImage configuration node name matching works. The default match
is on the single top-level DRAM configuration, if matching on subnodes
is required, then this board_stm32mp1_ddr_config_name_match() must be
overridden.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
The AV96 board does exist in multiple variants. To cater for all of
them, implement board code handling. There are two GPIOs which code
the type of the board, read them out and use the value to pick the
correct device tree from an fitImage.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Change-Id: Iddb330b9a66500495885457cbe17edc0eacaaf43
Here we improve clock support for recently introduced HSDK-4xD
board as well as finally enable external reset for the USB controller,
which is needed to recover USB functionality after "usb reset".
Add reset phandle to EHCI device tree node to make on-chip reset
controller usable with EHCI.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Anounce state of BIM switch which defines if U-boot is loaded
and started by preloader or not.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
HSDK and HSDK-4xD clock trees are slightly different.
commit 1dfb2ec0d7 ("ARC: HSDK: CGU: add support for timer clock")
introduce regression for HSDK board cause crash when setting
tunnel clock. Fix that.
Fixes: 1dfb2ec0d7 ("ARC: HSDK: CGU: add support for timer clock")
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
We don't want to allow change some clocks, i.e. DDR clock.
So allow to have set_clock to be unset in clock map.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
The clock trees of HSDK and HSDK-4xD vary so we need to prepare
CGU driver for multiple clock maps support.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
* constify clocks config data where is possible
* use more appropriate data types for clocks config
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Drop creg_div_oft offset as it doesn't vary (due to it is used for
CPU PLL only).
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
hsdk_axi_clk_cfg and hsdk_tun_clk_cfg clock divider structures
and functions for their processing are almost the same so
merge them to avoid code duplication.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Some systems may use a slightly larger stub to do PSCI for booting the RPi
family. The number of pages has been made configurable so that operating
systems building U-Boot for use in these kinds of environments can reserve
more memory in the EFI memory map.
Signed-off-by: Kyle Evans <kevans@FreeBSD.org>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
While the nearly-universal default for the Raspberry Pi family is to use
spin tables and the spin table implementation provided by the Raspberry Pi
Foundation, FreeBSD and others may use a PSCI implementation instead.
Accommodate these setups by allowing them to configure for more than one
page to be reserved in the initial reservation. The default reservation
remains as one page.
Signed-off-by: Kyle Evans <kevans@FreeBSD.org>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
If CONFIG_MMC_SDHCI_SDMA is enabled but the HW could not support it,
we no longer error out. Instead we do not enable it in the host.
Change the output from printf to debug as this isn't an error but only
additional information now.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Use the same environment size as the configs dedicated for rpi3 and rpi4.
This allows to switch between the builds and not to loose the settings
stored on the SD card.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
If Host controller doesn't support SDMA, it doesn't need to return
error. Because it can be worked with PIO mode.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Use phys2bus macro when dma address is accessed.
Some targets need to use pyhs2bus macro. (e.g, RPI4)
After applied it, SDMA mode can be used.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
We cannot rely on a parent bus that needs to be probed, until we know that
it is probed. That means that code in the ofdata_to_platdata() method
cannot rely on the parent bus being probed.
Move the ofdata code in the two serial drivers into a probe() method.
This fixes serial output on rpi_3b_32b with the following config.txt
options:
enable_uart=1
gpu_freq=250
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
At present the pinctrl nodes are not enabled in pre-relocation U-Boot so
the UARTs do not correctly select the pinconfig to enable the UART pins.
Fix this so that the U-Boot banner is printed.
This fixes serial output on rpi_3b_32b with the following config.txt
options:
enable_uart=1
gpu_freq=250
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: 9821636b64 (bcm2835_pinctrl: Probe pre-reloc)
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
As per Linux's driver, ID_MODE_DIS is only set when the PHY interface is
RGMII. Don't enable it for the rest of setups.
This has been seen to misconfigure RPi4's PHY when booting Linux.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Xilinx Versal platform uses dwc3 and hence its compatible string
needs to be added to dwc3 glue ids.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add a quirk to clear the GUSB3PIPECTL.DELAYP1TRANS bit,
which specifies whether disable delay PHY power change
from P0 to P1/P2/P3 when link state changing from U0
to U1/U2/U3 respectively.
Reference from below Linux commit,
commit <00fe081dc3a3> ("usb: dwc3: add dis_del_phy_power_chg_quirk")
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add tests for testing open-drain/open-source emulation in gpio-uclass.
It also adds two test3-gpios configured as GPIO_ACTIVE_LOW.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Handle the GPIOD_OPEN_DRAIN & GPIOD_OPEN_SOURCE flags to emulate open drain
and open source by setting the GPIO line as input depending on the
requested value.
The behaviour is taken from the Linux gpiolib.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable the second USB controller, which is connected to a hub with 4
ports. The first controller is for the OTG port and is currently not
supported.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
[narmstrong: removed useless DWC2_UTMI_WIDTH in meson64.h]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Wrap definition of board_usb_hw_init() around with #ifdef CONFIG_CMD_USB
to avoid warning: 'board_usb_hw_init' defined but not used
[-Wunused-function] when compiling without CONFIG_CMD_USB.
This patch makes sama5d27_som1_ek, sama5d2_ptc_ek and sama5d2_xplained
consistent with other boards that use the same #ifdef to avoid the warning.
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Josef Lusticky <josef@lusticky.cz>
Reviewed-by: Eugen Hristev <eugen.hristev@microchip.com>
2020-05-06 16:18:53 +03:00
4738 changed files with 38015 additions and 13882 deletions
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
