The USB0 instance of USB on AM62 SoC when configured to operate in the
Gadget mode of operation can be used to mount an MMC/SD card on the USB
Host. Hence, enable support for the USB Mass Storage (ums) command.
Since this config fragment corresponds to USB DFU functionality which
configures the USB Controller in Gadget mode of operation, other SoCs
which include this fragment for DFU functionality can make use of the
USB MASS Storage functionality as well.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
The USB0 instance of USB on J722S SoC is a Designware USB Controller with
the same glue layer (wrapper) as AM62 SoC. In order to support USB DFU boot
and USB DFU flash with USB0, enable the corresponding glue layer driver.
While at it, sync with savedefconfig.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
The config fragment "am62x_a53_usbdfu.config" which adds USB DFU support
for AM62x SoC is applicable to the AM62Px SoC as well. Hence, include it
in "am62px_evm_a53_defconfig" in order to enable support for USB DFU
flash and boot. Remove those configs from "am62px_evm_a53_defconfig" which
are present in the "am62x_a53_usbdfu.config" config fragment that is being
included.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Disable configs which are not required for USB DFU functionality, in
order to allow reusing this fragment for AM62Px SoC.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Include the TI K3 DFU environment to support DFU Boot and DFU Flash.
Also add "usb" to the list of "boot_targets". While at it, add a newline
at the end of the file.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
The config fragment "am62x_a53_usbdfu.config" which adds USB DFU support
for AM62x SoC is applicable to the AM62Ax SoC as well. Hence, include it
in "am62ax_evm_a53_defconfig" in order to enable support for USB DFU flash
and boot.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
CI:
* https://source.denx.de/u-boot/custodians/u-boot-efi/-/pipelines/24709
UEFI:
* create a parent device for all EFI block devices
* move lmb_map_update_notify() to EFI
* make efi_add_memory_map_pg() static
* remove comparisons to string literals from runtime
* ix potential deref-after-null
Other:
* avoid superfluous value check in lmb_map_update_notify()
* support more efi protocols in uuid_guid_get_str()
When building with qemu_arm64_defconfig with CONFIG_CC_OPTIMIZE_FOR_DEBUG=y
and CONFIG_EFI_LOADER=n an error undefined reference to efi_add_memory_map_pg
occurs.
Move the EFI dependent part of lmb_map_update_notify() to the EFI
sub-system.
Reported-by: Liya Huang <1425075683@qq.com>
Acked-by: Liya Huang <1425075683@qq.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Instead of testing the value of parameter op at runtime use an enum to
ensure that only valid values are used.
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Up to now root has been the parent device for all block devices created via
calling ConnectController(). This does not work well together with the
implementation of bootstd.
Add a dummy parent device for all EFI block devices.
With this change EFI block devices are also accessible via commands like
'cat', 'load', and 'ls'.
=> dm tree
Class Seq Probed Driver Name
-----------------------------------------------------------
efi 0 [ + ] EFI block driver `-- efi
blk 3 [ + ] efi_blk `-- efi.efiblk#0
partition 0 [ + ] blk_partition `-- efi.efiblk#0:1
=> ls efiloader 0:1
13 hello.txt
7 u-boot.txt
2 file(s), 0 dir(s)
=> cat efiloader 0:1 hello.txt
Hello world!
=> efidebug dh
0000000018df1700 (efi.efiblk#0:1)
/VenHw(dbca4c98-6cb0-694d-0872-819c650cb7b8)/HD(1,MBR,0xd1535d21,0x1,0x7f)
Block IO
Simple File System
Adjust the event dump unit test to consider the new event spy.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
For EFI runtime services, we manage to preserve string literals
by placing the .efi_runtime section just before .data and preserving
it when marking the runtime memory by marking surrounding boottime
code as runtime. This is ok for now but will break if we update any
linker scripts and decouple .text and .runtime sections.
So let's define the strings we used to compare in the appropriate
section for runtime services
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
After having been compared to a NULL value at efi_disk.c:426,
pointer 'part_info' is dereferenced at efi_disk.c:534.
Signed-off-by: Maks Mishin <maks.mishinFZ@gmail.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Add more EFI protocols GUIDs to the translation table used by
uuid_guid_get_str().
Signed-off-by: Vincent Stehlé <vincent.stehle@arm.com>
Cc: Tom Rini <trini@konsulko.com>
Use LwIP network stack and enable wget HTTP command. The tftpput command
is not currently supported by LwIP network stack so remove it.
Signed-off-by: E Shattow <e@freeshell.de>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Update the maintainer file and mark jh7110 / visionfive2 related files
with N: patterns.
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Variable $fdtfile needs to be set for automatically loading a device-tree
from the ESP or boot partition.
* Set CONFIG_DEFAULT_FDT_FILE in the defconfig.
* Add $fdtfile to the default environment.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
In previous commit, incoming standard passage is used by default
when initializing the bloblist, so explicitly BLOBLIST_PASSAGE is
no more needed.
Rename it as BLOBLIST_PASSAGE_MANDATORY to determine the behaviors
when an incoming transfer list does not exist or is invalid.
When it is selected, incoming standard passage is mandatory and
U-Boot will report an error when a valid incoming transfer list is
missing.
Signed-off-by: Raymond Mao <raymond.mao@linaro.org>
Refactor the xferlist to remove the relocating when bloblist passed
from the boot args.
Refactor bloblist init to use incoming standard passage by default
if a valid transfer list exists in the boot args.
For bloblist relocation, use the actual total size if it has a smaller
BLOBLIST_SIZE_RELOC.
Signed-off-by: Raymond Mao <raymond.mao@linaro.org>
Suggested-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
BootROM leave GPIO4_D6 configured as SDMMC_PWREN function and DW MCI
driver set PRWEN high on MMC_POWER_UP and low on MMC_POWER_OFF.
Similarly U-Boot also set PRWEN high before accessing mmc.
However, HW revision prior to v1.2 must pull GPIO4_D6 low to access
sdmmc. For HW revision v1.2 the state of GPIO4_D6 has no impact.
Model an always-on active low fixed regulator using GPIO4_D6 to fix
use of sdmmc on older HW revisions of the board.
Fixes: adeb5d2a4ba4 ("arm64: dts: rockchip: Add Radxa ROCK S0")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20241119230838.4137130-1-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[ upstream commit: 26c100232b09ced0857306ac9831a4fa9c9aa231 ]
(cherry picked from commit ca8e0bedbc790b19b11efc223677d178b8eeb74e)
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
When rgmii-rxid/txid/id phy-mode is used the MAC should not add RX
and/or TX delay. Currently RX/TX delay is configured as enabled using
zero as delay value for the rgmii-rxid/txid/id modes.
Change to disable RX and/or TX delay and using zero as delay value.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
When rgmii-rxid/txid/id phy-mode is used the MAC should not add RX
and/or TX delay. Currently RX/TX delay is configured as enabled using
zero as delay value for the rgmii-rxid/txid/id modes.
Change to disable RX and/or TX delay and using zero as delay value.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The pinmux bits for GPIO2-B0 to GPIO2-B6 actually have 2 bits width,
correct the bank flag for GPIO2-B. The pinmux bits for GPIO2-B7 is
recalculated so it remain unchanged. Add missing GPIO3-B1 to GPIO3-B7
pinmux data to rk3328_mux_recalced_data as mux register offset for these
pins does not follow rockchip convention.
This matches changes in following Linux commits:
- e8448a6c817c ("pinctrl: rockchip: fix pinmux bits for RK3328 GPIO2-B pins")
- 5ef6914e0bf5 ("pinctrl: rockchip: fix pinmux bits for RK3328 GPIO3-B pins")
- 128f71fe014f ("pinctrl: rockchip: correct RK3328 iomux width flag for GPIO2-B pins")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
clock/rk3288-cru.h in include/dt-bindings is almost identical to the
version in dts/upstream, remove the copy from include/dt-bindings to
only use the version from dts/upstream.
One clk, SCLK_MAC_PLL, is not part of the upstream bindings, this clk is
not used by upstream, in-tree or vendor DTs and can safely be dropped.
No functional change to board DTs is intended with this removal.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The device tree for rk3036 combined is now
available in the /dts/upstream directory.
Use imply OF_UPSTREAM to migrate all rk3036 boards.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Most Rockchip SoCs use 0x0 as DRAM base address, however some SoCs use
0x60000000 and RK3576 use 0x40000000 as DRAM base address.
CFG_SYS_SDRAM_BASE is defined with correct address for each SoC and
U-Boot proper use this to set correct gd->ram_base in setup_dest_addr().
SPL never assign any value to gd->ram_base and instead use the default,
0x0. Set correct gd->ram_base in dram_init() to ensure its correctness
in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
U-Boot only works correctly when it uses RAM below the 4G address
boundary on Rockchip SoCs. Limit usable gd->ram_top to max 4G.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Allow the first bank to extend beyond 4 GiB when the blob of space for
peripheral is located before start of DRAM, e.g. when start of DRAM
is 0x40000000 and continue beyond the 4 GiB mark.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In the GRF header file, some instances of UART2 pinmux are prefixed with
"GRF_UART2DBG" while others have "GRF_UART2DGB".
Since UART2 is the default console UART and used for debugging, it is
more likely the name should be UART2DBG.
Fix the ones that are wrong.
Fixes: a2c08df381 ("pinctrl: add driver for rk3399")
Fixes: fa72de1045 ("rockchip: arm64: rk3399: move grf register definitions to grf_rk3399.h")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Paul Kocialkowski <paulk@sys-base.io>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
These power rails must be on very early for the U-Boos TPL banner to be
show over debug UART.
This reverts commit 4576e65a5d.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The PP1500 and PP3000 power rails must be on very early for the U-Boot
TPL banner to be shown on debug UART.
Enable TPL_GPIO Kconfig option for bob and kevin to allow use of
spl_gpio.h functions in TPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
These power rails must be on very early for the U-Boos SPL banner to be
show over debug UART.
This reverts commit af518a1dfe.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add the dram_init_banksize function to the board file to properly set
DRAM memory sizes during boot.
The commit bc07851897 ("board: ti: Pull redundant DDR functions to a
common location and Fixup DDR size when ECC is enabled") relocated the
dram_init_banksize function from architecture specific initialization to
the TI board initialization code. As a result, boards relying on the
previous setup now require this function to be defined within their
board file to handle DRAM sizing correctly.
Without this function defined the following error appears during boot:
ERROR: Failed to allocate 0x1000 bytes below 0x0.
Fixes: bc07851897 ("board: ti: Pull redundant DDR functions to a common location and Fixup DDR size when ECC is enabled")
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Acked-by: Francesco Dolcini <francesco.dolcini@toradex.com>
The PCS exists only in GMAC1 and relates to SGMII interface and
is used to control the SGMII PHY.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
[trini: Adjust slightly for white space and to move 'start' to within if
block]
Add the dram_init_banksize function to the board file to properly set
DRAM memory sizes during boot.
The commit bc07851897 ("board: ti: Pull redundant DDR functions to a
common location and Fixup DDR size when ECC is enabled") relocated the
dram_init_banksize function from architecture specific initialization to
the TI board initialization code. As a result, boards relying on the
previous setup now require this function to be defined within their
board file to handle DRAM sizing correctly.
Without this function defined the following error appears during boot:
ERROR: Failed to allocate 0x1000 bytes below 0x0.
Fixes: bc07851897 ("board: ti: Pull redundant DDR functions to a common location and Fixup DDR size when ECC is enabled")
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Acked-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Add a new event which handles this function refer to commit
("91caa3bb89b1 event: Use an event to replace last_stage_init()")
Signed-off-by: Michael Chang <zhang971090220@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Return value of a function 'strtok_r' is dereferenced at kwbimage.c:1655
without checking for NULL, but it is usually checked for this function.
Signed-off-by: Maks Mishin <maks.mishinFZ@gmail.com>
When performing a build consisting of only a defconfig target and then
this tool, we were missing two dependencies. Add them.
Signed-off-by: Tom Rini <trini@konsulko.com>
The PRNG implementing the random() function only has 2^31 states and
therefore is unsafe to use for cryptography. Use arc4random() instead.
Fixes: cc34f04efd ("tools: image-host.c: use random instead of rand")
Addresses-Coverity-ID: 312953 Calling risky function
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
As per TRM[0] Section 8.7.1 "TPS6594-Q1 Registers", LDOx_Vout
bit 6-1, define the NVM voltage settings.
Along side table 8-4 of above TRM, shows voltage to value mapping.
Driver wrongly using bits 5-1 to calculate voltage, and to convert
voltage to value driver was using buck's calculation.
So fix those calculation.
[0]: https://www.ti.com/lit/ds/symlink/tps6594-q1.pdf
Fixes: 5d7dbd22cf ("power: regulator: tps65941: use function callbacks for conversion ops")
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
The struct contains an iomem pointer that we later remap and update.
Remove const from the struct definition.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
First set of u-boot-at91 features for the 2025.07 cycle:
This feature set includes improvements on the atmel-quadspi driver, a
fix for the nand driver, and improvements on the pinctrl driver to be
able to use the Linux DT (also sync on the DT side as well).
