The ENV size and offset were changed to different
values in Beacon's downstream release. Change them to the
same values as the downstream for consistent behavior.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Since any changes to the RZ/G2 family go through Marek's tree,
update the MAINTAINER file to automatically show his name
when running get_maintainer.pl. Without this, he is not
copied.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reserve 4 kiB of space in 64bit R-Car DTs when those DTs are compiled
to permit patching in OpTee-OS /firmware node, /reserved-memory node,
possibly also additional /memory@ nodes and RPC node by TFA.
This duplicates behavior in arch/arm/dts/Makefile with OF_UPSTREAM.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Remove leftover DTSI files after OF_UPSTREAM conversion.
Those are no longer used and no longer necessary, remove them.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Adam Ford <aford173@gmail.com>
Javier Martinez Canillas <javier@dowhile0.org> says:
Hello,
I noticed that the IGEPv2 board did not boot anymore with mainline U-Boot.
This was caused by a driver change to allocate its platform data before
relocation and U-Boot not having enough pre-relocation heap size for this.
This series fixes this issue and also makes the board support more modern,
by enabling DM for SPL and migrating the IGEP boards to use upstream DTBs.
Enable OF_UPSTREAM to use upstream DT and add a ti/omap/ prefix to the
DEFAULT_DEVICE_TREE config option.
That way, a DTS from the upstream dts/upstream/src/ directory is used
instead of the arch/$(ARCH)/dts/ directory. These in turn are removed.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Enric Balletbo i Serra <eballetbo@gmail.com>
This change is heavily based on commit e0cc7df9fd ("omap3_beagle: Update
for DM SPL support"), that did the same update for the OMAP3 Beagle board.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Enric Balletbo i Serra <eballetbo@gmail.com>
There are no SPI peripherals in neither the IGEPv2 board nor the IGEP COM
Module, so there's no reason to have this enabled in the boards defconfig.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Enric Balletbo i Serra <eballetbo@gmail.com>
The IGEPv2 board boot started to fail since the commit afd4f15a39 ("spi:
omap3_spi: Read platform data in ofdata_to_platdata()"). Because this made
the OMAP3 SPI controller driver to allocate its platform data before doing
a relocation, but the igep0x00 config sets this pool size to just 1 KiB.
Increase the pre-relocation malloc heap size to 16 KiB, as is set by other
OMAP3 boards. This not only restores booting but also makes it consistent.
Leave the SPL pool size to the previous 1 KiB size since 16 KiB may not be
a possible size in that constrained environment and is also the value that
is set by other OMAP3 boards.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Use CSR_UCCTLCOMMAND instead of CSR_MCCTLCOMMAND
to do cache flush operation in M-mode and S-mode.
Signed-off-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Cache could be enabled in harts_early_init board-specific hook,
so remove cache enablement in start.S
Signed-off-by: Leo Yu-Chi Liang <ycliang@andestech.com>
A given AMP configuration for a board may make either one, or neither
of, the ethernet ports available to U-Boot. The Icicle's init code will
fail if mac1 is not present, so move it to the optional approach taken
for mac0.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Node offsets returned by libfdt can contain negative error numbers, so
the variable type should be "int". As things stand, if the ethernet
nodes are not found in the early init callback, the if (node < 0) tests
pass and the code errors out while trying to set the local-mac-address
for a non-existent node.
Fixes: 64413e1b7c ("riscv: Add Microchip MPFS Icicle Kit support")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Most of the current URLs should be redirected but some aren't already,
so let's anticipate more IT hiccups by migrating to new URLs.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
The Theobroma address bounces as Philipp is not working there anymore,
so let's update with the one that seems to be working right now.
Cc: Philipp Tomsich <philipp.tomsich@vrull.eu>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
The address we load TFA and OPTEE is configurable by the
CONFIG_K3_{ATF,OPTEE)_LOAD_ADDR, but the DT node reservations remain
static which can cause some confusion about where exactly these firmware
are exactly. Fix this by updating the reserved-memory{} nodes when the
loaded address does not match the address in DT.
Reported-by: Andrew Davis <afd@ti.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
For pcr_read and pcr_extend commands allow the digest algorithm to be
specified by an additional argument. If not specified it will default to
SHA256 for backwards compatibility.
Additionally update test_tpm2.py for the changes in output in pcr_read
which now shows the algo and algo length in the output.
A follow-on to this could be to extend all PCR banks with the detected
algo when the <digest_algo> argument is 'auto'.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Instead of displaying what looks like an error message if a
gpio-reset dt prop is missing for a TPM display a warning that
having a gpio reset on a TPM should not be used for a secure production
device.
TCG TIS spec [1] says:
"The TPM_Init (LRESET#/SPI_RST#) signal MUST be connected to the
platform CPU Reset signal such that it complies with the requirements
specified in section 1.2.7 HOST Platform Reset in the PC Client
Implementation Specification for Conventional BIOS."
The reasoning is that you should not be able to toggle a GPIO and reset
the TPM without resetting the CPU as well because if an attacker can
break into your OS via an OS level security flaw they can then reset the
TPM via GPIO and replay the measurements required to unseal keys
that you have otherwise protected.
Additionally restructure the code for improved readability allowing for
removal of the init label.
Before:
- board with no reset gpio
u-boot=> tpm init && tpm info
tpm_tis_spi_probe: missing reset GPIO
tpm@1 v2.0: VendorID 0x1114, DeviceID 0x3205, RevisionID 0x01 [open]
- board with a reset gpio
u-boot=> tpm init && tpm info
tpm@1 v2.0: VendorID 0x1114, DeviceID 0x3205, RevisionID 0x01 [open]
After:
- board with no reset gpio
u-boot=> tpm init && tpm info
tpm@1 v2.0: VendorID 0x1114, DeviceID 0x3205, RevisionID 0x01 [open]
- board with a reset gpio
u-boot=> tpm init && tpm info
tpm@1: TPM gpio reset should not be used on secure production devices
tpm@1 v2.0: VendorID 0x1114, DeviceID 0x3205, RevisionID 0x01 [open]
[1] https://trustedcomputinggroup.org/wp-content/uploads/TCG_PCClientTPMInterfaceSpecification_TIS__1-3_27_03212013.pdf
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The Indiedroid Nova is a Rockchip RK3588S based SBC from Indiedroid.
Specifications:
Rockchip RK3588S SoC
4x ARM Cortex-A76, 4x ARM Cortex-A55
4/8/16GB memory LPDDR4x
Mali G610MC4 GPU
Optional eMMC
2x USB 2.0, 2x USB 3.0, 1x USB 3.0 C port with DP Alt
1x MIPI-CSI Port (4-lane or 2x 2-lane)
1x MIPI-DSI 4-lane connector
1x Micro HDMI 2.1 output, 1x DP 1.4 output
Gigabit Ethernet
Realtek RTL8821CS WiFi
4 pin debug UART connector
40 pin GPIO header
Size: 85mm x 56mm (Raspberry Pi Form Factor)
Kernel commit:
3900160e164b ("arm64: dts: rockchip: Add Indiedroid Nova board")
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Powkiddy X55 is a Rockchip RK3566 based handheld gaming device.
UART, ADC, eMMC, and SDMMC are tested to work in U-Boot and this
successfully boots mainline Linux.
Kernel commit:
e99adc97e21a ("arm64: dts: rockchip: Add Powkiddy X55")
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
U-Boot proper pre-reloc is currently running out of memory and it is
thus impossible to boot into U-Boot CLI.
Fix this by migrating to the common bss and stack addresses for PX30,
which drastically increases the size of the pre-reloc allocation pool (8
times bigger now). The memory layout in SPL and U-Boot proper now
match the other SoCs' using ROCKCHIP_COMMON_STACK_ADDR.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
See commit 008ba0d56d ("rockchip: Add common default bss and stack
addresses") for memory layout. This migrates PX30 to use the new layout,
except for TPL. Indeed, PX30 is extremely limited in SRAM, so we need to
be extra careful about what goes into the TPL and how much we can
allocate there, so let's keep the current value for
TPL_SYS_MALLOC_F_LEN (already present in the PX30-specific Kconfig, from
an earlier commit).
This will allow us to use the same memory layout on one more Rockchip
SoC, which is always a nice thing. Additionally, this will make it
easier to fix U-Boot proper pre-reloc running out of memory on PX30 in a
subsequent commit.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
This is the kind of setting that typically doesn't need to be changed
between boards based on the same SoC, so let's make it the default in
PX30 Kconfig so we don't have to care about it in the defconfig if we
don't want to.
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
All parts expect the SPLL to run at 702MHz. In U-Boot it's the SPLL_HZ
declaring this rate and in the kernel it's a fixed clock definition.
While everything is expecting 702MHz, the SPLL is not running that
frequency when coming from the bootrom though, instead it's running
at 351MHz and the vendor-u-boot just sets it to the expected frequency.
The SPLL itself is located inside the secure-BUSCRU and in theory
accessible as an SCMI clock, though this requires an unknown amount
of cooperation from trusted-firmware to set at a later stage, though
during the SPL stage we can still access the relevant CRU directly.
The SPLL is for example necessary for the DSI controllers to produce
output.
As the SPLL is "just" another rk3588 pll, just set the desired rate
directly during the SPL stage.
Tested on rk3588-rock5b and rk3588-tiger by reading back the PLL rate
and also observing working DSI output with this change.
Fixes: 6737771600 ("rockchip: rk3588: Add support for sdmmc clocks in SPL")
Suggested-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Migrate RV1126 boards that exists in Linux v6.8 to use OF_UPSTREAM.
Following targets is migrated to use OF_UPSTREAM:
- rv1126-edgeble-neu2 : Board is an industrial form factor
IO board.
- sonoff-ihost-rv1126 : Gateway device designed to provide a
Smart Home Hub.
Cc: Tim Lunn <tim@feathertop.org>
Cc: Jagan Teki <jagan@edgeble.ai>
Reviewed-By: Tim Lunn <tim@feathertop.org>
Tested-By: Tim Lunn <tim@feathertop.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Anand Moon <anand@edgeble.ai>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
After the conversion of RV1108 to OF_UPSTREAM,
include/dt-bindings/clock/rv1108-cru.h is no longer needed because
there is dts/upstream/include/dt-bindings/clock/rv1108-cru.h from
upstream Linux.
Remove the unneeded rv1108-cru.h file.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.
This reverts commit c8ffd1356d, reversing
changes made to 2ee6f3a5f7.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
Specifying a file in an EXT4 or FAT partition on a virtio device as
environment location failed because virtio hadn't been initialized by
the time the environment was loaded. This patch mirrors commit
54ee5ae841 ("Add SCSI scan for ENV in EXT4 or FAT") in issue and
fix, just for a different kind of block device.
The additional include in include/virtio.h is needed so all functions
called there are defined, the alternative would have been to include
dm/device.h separately in the env/ sources.
Checkpatch suggests using "if (IS_ENABLED(CONFIG...))" instead of
"#if defined(CONFIG_...)", I'm sticking to the style of the existing
code here.
Signed-off-by: Fiona Klute <fiona.klute@gmx.de>
CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Bin Meng <bmeng.cn@gmail.com>
CC: Rogier Stam <rogier@unrailed.org>
u-boot-dfu-20240516
- Fix cdns3 low power hang via fast access bit
- Multiple dwc3 gadget fixes, mainly for USB support on TI AM6232
- Consistent USB_GADGET_MANUFACTURER for PHYTEC boards
- MAINTAINERS file update for u-boot-dfu
Upstream Linux commit 87dd96111b0b.
When operating in USB 2.0 speeds (HS/FS), if GUSB2PHYCFG.ENBLSLPM or
GUSB2PHYCFG.SUSPHY is set, it must be cleared before issuing an endpoint
command.
Current implementation only save and restore GUSB2PHYCFG.SUSPHY
configuration. We must save and clear both GUSB2PHYCFG.ENBLSLPM and
GUSB2PHYCFG.SUSPHY settings. Restore them after the command is
completed.
DWC_usb3 3.30a and DWC_usb31 1.90a programming guide section 3.2.2
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20240412202611.3565052-5-alexander.sverdlin@siemens.com
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
