Agilex7 M-series support has been added using upstream Linux DTS.
socfpga_agilex_socdk-u-boot.dtsi was updated to support both Agilex and
Agilex7 M-series platforms.
Signed-off-by: Tingting Meng <tingting.meng@altera.com>
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
Migrate the legacy Agilex platform to use the upstream Linux device tree
configuration. This helps reduce maintenance overhead and aligns U-Boot
with the Linux kernel's DTS hierarchy and naming conventions.
This change improves consistency between U-Boot and Linux by removing
custom/legacy DTS handling and instead relying on the standardized
definitions provided by the upstream Linux DTS.
Signed-off-by: Tingting Meng <tingting.meng@altera.com>
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
Reorganize misplaced properties by moving board-common settings from
socfpga_agilex_socdk-u-boot.dtsi to socfpga_agilex-u-boot.dtsi to maintain
proper separation between common and board-level configurations.
Signed-off-by: Tingting Meng <tingting.meng@altera.com>
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
SPL checks for a magic word in the system manager's scratch
register to determine if an L2 reset has occurred. If detected,
SPL places all slave CPUs (CPU1–3) into WFI mode. The master
CPU (CPU0) then initiates a warm reset by writing to the RMR_EL3
system register and also enters WFI mode.
This warm reset flow is handled entirely within the HPS. The
function `socfpga_sysreset_request()` triggers the warm
reset, and upon SPL re-entry, the updated `lowlevel_init_soc64.S`
handles the necessary initialization.
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
Put all slave CPUs (CPU1-3) into WFI mode. Master CPU (CPU0) writes
the magic word into system manager's scratch register to indicate
the system has performed L2 reset and request reset manager to
perform hardware handshake and then trigger L2 reset. CPU0 put
itself into WFI mode. L2 reset will reboot all HPS CPU cores after
which all HPS cores are in WFI mode. L2 reset is followed by warm
reset request by SPL via RMR_EL3 system register.
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
Agilex retrieves its clock manager address via probing its own clock
driver model during the SPL initialization.
Therefore, excluding Agilex from calling its clock driver in misc
driver to retrieve the clock manager address.
Once all SoC64 devices has been successfully transition to clock
driver model method, this implementation will be cleaned up.
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
The DDR data rate must be set correctly in the DDRIOCTRL
register according to the Actual Clock Frequency (ACF) value.
By enabling the reading of ACF value from bit 18 of the boot
scratch register during initialization, the DDR data rate is
able to be configured accurately.
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
The boot scratch cold reg 8 is shared between DBE, DDR init progress
update and Linux EDAC. This patch defines how the bits are used by
respective features above and their macro names used in U-Boot.
Signed-off-by: Tien Fong Chee <tien.fong.chee@altera.com>
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
Setting up firewall regions based on SDRAM memory banks configuration
(up to CONFIG_NR_DRAM_BANKS banks) instead of using whole address space.
First 1 MiB (0 to 0xfffff) of SDRAM is configured as secure region,
other address spaces are non-secure regions. The ARM Trusted Firmware (ATF)
image is located in this first 1 MiB memory region. So, this can prevent
software executing at non-secure state EL0-EL2 and non-secure masters
access to secure region.
Add common function for firewall setup and reuse for all SoC64 devices.
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
The base address of system manager can be retrieved
using DT framework through the system manager driver.
Enable system manager support for Agilex by probing the
system manager driver to initialize during SPL boot up.
Signed-off-by: Boon Khai Ng <boon.khai.ng@altera.com>
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
Refactor system manager initialization by searching for system manager
alias in Agilex5 device tree instead of manually passing node name to
the device model calling function
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
Replace cm_wait_for_fsm() function with wait_for_bit_le32() function
which supports accurate timeout.
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
Asynchronous aborts were previously masked at SPL
entry.
To ensure early detection of system errors
such as ECC faults or bus errors, asynchronous aborts
should be explicitly unmasked by clearing the A-bit in
the DAIF register during Agilex SPL initialization.
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
# Conflicts:
# arch/arm/mach-socfpga/spl_agilex.c
Enable backup for data section to support warm reset in Agilex SPL as
no SPL image would be reloaded in warm reset.
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
Update Agilex SPL code to implement device tree model
for firewall registers setup by using DTreg driver to
probe from device tree for the firewall settings instead
of calling firewall driver function.
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
Combine all MMC, NAND and QSPI configs into single defconfig which is named
as "socfpga_agilex_defconfig". This will be the default defconfig to use.
It supports booting from all three flashes using ARM Trusted Firmware (ATF)
as the secure runtime monitor.
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
Update the ARMv8 generic timer frequency register (cntfrq_el0)
with the actual hardware timer frequency (COUNTER_FREQUENCY_REAL).
The generic timer frequency was set to 0x200000000 during boot clk
which needs to be set to 0x400000000 when transition from boot clk
to PLL clk.
This will ensure that subsequent timer operations are based on the
correct frequency, ensuring accurate timekeeping.
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
In dwxgmac_of_get_mac_mode there is a test for mac_mode which will
return if false. After this point mac_mode is guaranteed to be true so
there is no need to test for this. Remove that test.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
In xgmac_probe there is a direct return after the point where unwind
gotos start to be used to undo actions performed by earlier code. Use
the appropriate unwind goto instead.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
Various fixes for smatch warnings, the i2c one might be also coming in
via Heiko / I2C tree, let me know if there is conflict.
There is also W77Q51NW SPI NOR ID support, with the DT portion omitted
for now.
Enable support for Winbond SPI NOR on Retronix R-Car V4H Sparrow Hawk board,
this is required to support W77Q51NW on new board revision EVTB1 operational.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
In rswitch_probe the error detection after the call to devm_clk_get is
very wrong. It checks the value of ret which is uninitialised at that
point. Instead it should be using the macros for including errors into
pointers.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add IDs for Winbond W77Q51NW, 512M-bit Secure Serial Flash Memory
with Post-Quantum Cryptography, Dual/Quad SPI, QPI and DTR . The
flash part is similar to W25Q512NWM .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
In rcar_iic_xfer if nmsgs == 0 the ret will not be assigned to. As ret
will always be 0 if the for loop is entered, may as well just return 0.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
In rcar_clk_set_rate64_div_table the unsigned variable 'value' is used
to receive the return value from rcar_clk_get_table_val which returns an
int and then attempts to test for being less than 0, which can never be
true. Instead declare value as an int so the code can behave as
expected. Also remove initial values from 'value' and 'div' as they are
not needed.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
i2c updates for v2025.10-rc2
bugfixes:
- rcar_iic: do not use unitialised variable
from Andrew
- fix coverity issue in cmd/i2c.c
from Heiko
new driver:
late, but hopefully okay for rc2, as already picked up when
merge window was open, but there was a problem in common code,
which is now fixed
- new i3c driver support from Dinesh
Add simple test to check i3c controller defined in sandbox test DT.
Basically, this test case will check validity of the i3c controller
by probing it and perform basic commands of cmd/i3c.c
Signed-off-by: Dinesh Maniyam <dinesh.maniyam@altera.com>
Add i3c command file to support select, get i3c device
target list, read and write operation.
Signed-off-by: Dinesh Maniyam <dinesh.maniyam@altera.com>
Fix the I3C device with spike filter unable to detect issue by setting
tHIGH_INIT to 200ns for first broadcast address.
This is according to MIPI SPEC 1.1.1 for first broadcast address
which is already part of linux upstreamed patch.
Signed-off-by: Dinesh Maniyam <dinesh.maniyam@altera.com>
Picked linux i3c driver upstraming patch to fix the issue to
probe for i3c controller without slave device attached.
With this fix, the ret check will be on command error and will success
without slave device attached.
Signed-off-by: Dinesh Maniyam <dinesh.maniyam@altera.com>
Enable the Kconfig and Makefile for the MIPI DWI3C driver.
hs: fixed typo on drivers/i3c/master/Kconfig
Signed-off-by: Dinesh Maniyam <dinesh.maniyam@altera.com>
Enable i3c general uclass driver. This uclass driver will have
genaral read and write api to call the specific i3c driver.
Signed-off-by: Dinesh Maniyam <dinesh.maniyam@altera.com>
Enable driver for Synopsis MIPI DWI3C for the family
device agilex5. This driver is migrated from linux version 6.6.37 LTS
Signed-off-by: Dinesh Maniyam <dinesh.maniyam@altera.com>
In rcar_iic_xfer if nmsgs == 0 the ret will not be assigned to. As ret
will always be 0 if the for loop is entered, may as well just return 0.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
The U-Boot environment was previously stored in the boot loader stream
using ldr, but it has been replaced by the default environment built
into the U-Boot executable or an environment on external storage
Fixes: ea3310e8aa ("Blackfin: Remove")
Signed-off-by: Philip Molloy <philip.molloy@analog.com>
Reviewed-by: Greg Malysa <malysagreg@gmail.com>
Use the same logic as is used for MAC address where bdi shows mac address
for current device where index (idx) is used to point to correct IP address
which is read and show.
Signed-off-by: Michal Simek <michal.simek@amd.com>
