Cleanup

* Patch by Thomas Lange 07 Oct 2004:
  Updated README for DBAu1x00 boards to match current status

CHANGELOG

@@ -2,6 +2,201 @@
 Changes since U-Boot 1.1.1:
 ======================================================================
 
+* Enable NAND flash support for NC650 board.
+
+* Patch by Thomas Lange 07 Oct 2004:
+  Updated README for DBAu1x00 boards to match current status
+
+* Patch by Philippe Robin, 28 Sept 2004:
+  Fix Flash support for Versatile.
+
+* Patch by Roger Blofeld, 16 Sep 2004:
+  Fix timeout for DHCP command retry
+
+* Patch by Pantelis Antoniou, 14 Sep 2004:
+  Fix early serial hang when CONFIG_SERIAL_MULTI is defined.
+
+* Patch by Pantelis Antoniou, 14 Sep 2004:
+  Kick watchdog when bz-decompressing
+
+* Fix CFG_HZ problems on AT91RM9200 systems
+  [Remember: CFG_HZ should be 1000 on ALL systems!]
+
+* Patch by Gridish Shlomi, 30 Aug 2004:
+  - Add support to revA version of PQ27 and PQ27E.
+  - Reverted MPC8260ADS baudrate back to original 115200
+
+* Patch by Hojin, 17 Sep 2004:
+  Fix typo in cfi_flash.c
+
+* Patch by Mark Jonas, 09 September 2004:
+  mtest's data line test (with CFG_ALT_MEMTEST set) returned a wrong
+  error message
+
+* Patch by Mark Jonas, 31 August 2004:
+  Added option CFG_XLB_PIPELINING to enable XLB pipelining. This
+  improves FTP performance for MPC5200 systems. Enabled for IceCube
+  by default.
+
+* Patch by Michael Bendzick, 30 Aug 2004:
+  - Improve platform.S code for omap1510inn that detects whether code
+    is running from SDRAM or not. Patch allows SDRAM to be configured
+    if code is running out of SRAM at 0x20000000.
+
+* Patch by Frederick Klatt, 30 Aug 2004:
+  Add support for the Wind River SBC8540/SBC8560 boards
+
+* Configure SX1 board to use drivers/cfi_flash.c
+
+* Patches by Michael Bendzick, 30 Aug 2004:
+  - Configure omap1510inn board to use drivers/cfi_flash.c
+  - Make drivers/cfi_flash.c protect environment and redundant
+    environment.
+
+* Patch by Steven Scholz, 23 Jun 2004:
+  - Add script (tools/img2brec.sh) to programm U-Boot into
+    (Synch)Flash using the Bootstrap Mode of the MC9328MX1/L
+
+* Patches by Scott McNutt, 24 Aug 2004:
+  - Add support for Altera Nios-II processors.
+  - Add support for Psyent PCI-5441 board.
+  - Add support for Psyent PK1C20 board.
+
+* Patches by Jon Loeliger, 24 Aug 2004:
+  - Add support for the MPC8541 and MPC8555 CDS boards
+  - Cleanup eth?addr handling: make dependent on CONFIG_ETH?ADDR
+  - Convert MPC85xxADS to use common CFI flash driver
+  - Fix PCI window on MPC85xx; remove unneeded PCI initialization
+    from board_early_init_f()
+  - Provide SW workaround for PCI initialization on 85xx CDS
+
+* Patches by George G. Davis, 24 Aug 2004:
+  - Enable ramdisk/initrd tagged param support for omap1610h2_config
+  - Remove static network setup defaults from mx1ads_config
+  - update ARM boards to use constants from mach-types.h
+
+* Patch by Gary Jennejohn, 04 Oct 2004:
+  - fix I2C on at91rm9200
+  - add support for Ricoh RS5C372A RTC
+
+* Patch by Gary Jennejohn, 01 Oct 2004:
+  - add support for CMC PU2 board
+  - add support for I2C on at91rm9200
+
+* Patch by Gary Jennejohn, 28 Sep 2004:
+  fix baudrate handling on at91rm9200
+
+* Patch by Yuli Barcohen, 22 Aug 2004:
+  - remove ZPC.1900 board-specific flash driver;
+    switch the port to generic CFI driver;
+  - port clean-up
+
+* Patch by Hinko Kocevar, 21 Aug 2004:
+  Add calc_fbsize() function used with VIDEOLFB_TAG on TRAB
+
+* Clean up tools/bmp_logo.c to not add trailing white space
+
+* Patch by Hinko Kocevar, 21 Aug 2004:
+  - Group common framebuffer functions in common/lcd.c
+  - Group common framebuffer macros and #defines in include/lcd.h
+  - Provide calc_fbsize() for video ATAG
+
+* Patch by Sam Song, 21 August 2004:
+  - Fix a typo in README
+  - Align "(RO)" output for "flinfo" after "protect on"
+  - Add RESET support for RPXlite_DW board; adjust CPU:BUS frequency
+    ratio 1:1 when core frequency less than 50MHz
+
+* Patches by Hinko Kocevar, 21 Aug 2004:
+  - fix some "use of label at end of compound statement" warnings
+  - Define type of LCD panel on lubbock board if CONFIG_LCD is used
+
+* Patch by Steven Scholz, 16 Aug 2004:
+  - Introducing the concept of SoCs "./cpu/$(CPU)/$(SOC)"
+  - creating subdirs for SoCs ./cpu/arm920t/imx and ./cpu/arm920t/s3c24x0
+  - moving SoC specific code out of cpu/arm920t/ into cpu/arm920t/$(SOC)/
+  - moving drivers/s3c24x0_i2c.c and drivers/serial_imx.c out of drivers/
+    into cpu/arm920t/$(SOC)/
+
+* Patches by Sean Chang, 09 Aug 2004:
+  - Added support for both 8 and 16 bit mode access to System ACE CF
+    through MPU.
+  - Fixed missing System ACE CF device during get FAT partition info
+    in fat_register_device function.
+  - Enabled System ACE CF support on ML300.
+
+* Patch by Sean Chang, 09 Aug 2004:
+  Synch defines for saveenv and do_saveenv functions so they get
+  compiled under the same statement.
+
+* Patch by Sean Chang, 09 Aug 2004:
+  - Added I2C support for ML300.
+  - Added support for ML300 to read out its environment information
+    stored on the EEPROM.
+  - Added support to use board specific parameters as part of
+    U-Boot's environment information.
+  - Updated MLD files to support configuration for new features
+    above.
+
+* Patches by Travis Sawyer, 05 Aug 2004:
+  - Remove incorrect bridge settings for eth group 6
+  - Add call to setup bridge in ppc_440x_eth_initialize
+  - Fix ppc_440x_eth_init to reset the phy only if its the
+    first time through, otherwise, just check the phy for the
+    autonegotiated speed/duplex.  This allows the use of netconsole
+  - only print the speed/duplex the first time the phy is reset.
+
+* Patch by Shlomo Kut, 29 Mar 2004:
+  Add support for MKS Instruments "Quantum" board
+
+* Fix build problem with Cogent boards;
+  avoid using <asm/byteorder.h> when using the host compiler
+
+* Patch by Ganapathi C, 04 Aug 2004:
+  Fix NFS timeout issue
+
+* Patch by Yuli Barcohen, 19 Jul 2004:
+  - Fix host tools building in Cygwin environment
+  - Fix header files search order for host tools
+
+* Patch by Tom Armistead, 19 Jul 2004:
+  Fix kgdb.S support for 74xx_75x cpu
+
+* Patch by Jon Loeliger, 15 Jul 2004:
+  Fix MPC85xx I2C driver
+
+* Fix problems with CDROM drive as slave device on Lite5200 IDE bus.
+
+* Patch by Stephen Williams, 15 July 2004
+  Set the PCI class code for JSE board as part of PCI interface setup
+
+* Patch by Michael Bendzick, 15 Jul 2004:
+  Fix problem with writes with odd sizes in drivers/cfi_flash.c when
+  CFG_FLASH_USE_BUFFER_WRITE is set
+
+* Patch by Yuli Barcohen, 13 Jul 2004:
+  Allow clock setting on MPC866/MPC885 series chips according to
+  environment variable `cpuclk'
+
+* Patch by Yuli Barcohen, 20 Apr 2004:
+  Remove unnecessary redefine of CPM_DATAONLY_SIZE for MPC826x
+
+* Patch by Vincent Dubey, 24 Sep 2004:
+  Add support for xaeniax board
+
+* Add comment about non-GPL character of standalone applications to
+  COPYING file
+
+* Fix FEC ethernet problem on NSCU board.
+
+* Patch by Gary Jennejohn, 09 Sep 2004:
+  allow to use USART1 as console port on at91rm9200dk boards
+
+* Patch by Stefan Roese, 16 Sep 2004:
+  Update AR405 board.
+
+* Fix SysClk handling for PPChameleon and CATcenter boards
+
 * Patch by Detlev Zundel, 08 Sep 2004:
   Update etags build target
 

COPYING

@@ -1,3 +1,14 @@
+  NOTE! This copyright does *not* cover the so-called "standalone"
+applications that use U-Boot services by means of the jump table
+provided by U-Boot exactly for this purpose - this is merely
+considered normal use of U-Boot, and does *not* fall under the
+heading of "derived work". Also note that the GPL below is
+copyrighted by the Free Software Foundation, but the instance of code
+that it refers to (the U-Boot source code) is copyrighted by me and
+others who actually wrote it. -- Wolfgang Denk
+
+=======================================================================
+
 		    GNU GENERAL PUBLIC LICENSE
 		       Version 2, June 1991
 

CREDITS

@@ -223,6 +223,10 @@ N: Sangmoon Kim
 E: dogoil@etinsys.com
 D: Support for debris board
 
+N: Frederick W. Klatt
+E: fred.klatt@windriver.com
+D: Support for Wind River SBC8540/SBC8560 boards
+
 N: Thomas Koeller
 E: tkoeller@gmx.net
 D: Port to Motorola Sandpoint 3 (MPC8240)
@@ -286,7 +290,10 @@ D: Support for Samsung ARM920T SMDK2410 eval board
 
 N: Scott McNutt
 E: smcnutt@psyent.com
-D: Support for Altera Nios-32 CPU, for Nios Cyclone Development Kit (DK-1C20)
+D: Support for Altera Nios-32 CPU
+D: Support for Altera Nios-II CPU
+D: Support for Nios Cyclone Development Kit (DK-1C20)
+W: http://www.psyent.com
 
 N: Rolf Offermanns
 E: rof@sysgo.de

MAINTAINERS

@@ -430,6 +430,18 @@ Scott McNutt <smcnutt@psyent.com>
 
 	DK1C20			Nios-32
 
+#########################################################################
+# Nios-II Systems:							#
+#									#
+# Maintainer Name, Email Address					#
+#	Board			CPU					#
+#########################################################################
+
+Scott McNutt <smcnutt@psyent.com>
+
+	PCI5441			Nios-II
+	PK1C20			Nios-II
+
 #########################################################################
 # MicroBlaze Systems:							#
 #									#

MAKEALL

@@ -34,23 +34,24 @@ LIST_5xxx="	\
 #########################################################################
 
 LIST_8xx="	\
-	Adder87x	GENIETV		MBX860T		RBC823		\
-	AdderII		GTH		MHPC		rmu		\
-	ADS860		hermes		MPC86xADS	RPXClassic	\
-	AMX860		IAD210		MPC885ADS	RPXlite		\
-	c2mon		ICU862_100MHz	MVS1		RPXlite_DW	\
-	CCM		IP860		NETPHONE	RRvision	\
-	cogent_mpc8xx	IVML24		NETTA		SM850		\
-	ELPT860		IVML24_128	NETTA2		SPD823TS	\
-	ESTEEM192E	IVML24_256	NETTA_ISDN	svm_sc8xx	\
-	ETX094		IVMS8		NETVIA		SXNI855T	\
-	FADS823		IVMS8_128	NETVIA_V2	TOP860		\
-	FADS850SAR	IVMS8_256	NX823		TQM823L		\
-	FADS860T	KUP4K		pcu_e		TQM823L_LCD	\
-	FLAGADM		KUP4X		QS823		TQM850L		\
-	FPS850L		LANTEC		QS850		TQM855L		\
-	GEN860T		lwmon		QS860T		TQM860L		\
-	GEN860T_SC	MBX		R360MPI		v37		\
+	Adder87x	GENIETV		MBX860T		R360MPI		\
+	AdderII		GTH		MHPC		RBC823		\
+	ADS860		hermes		MPC86xADS	rmu		\
+	AMX860		IAD210		MPC885ADS	RPXClassic	\
+	c2mon		ICU862_100MHz	MVS1		RPXlite		\
+	CCM		IP860		NETPHONE	RPXlite_DW	\
+	cogent_mpc8xx	IVML24		NETTA		RRvision	\
+	ELPT860		IVML24_128	NETTA2		SM850		\
+	ESTEEM192E	IVML24_256	NETTA_ISDN	SPD823TS	\
+	ETX094		IVMS8		NETVIA		svm_sc8xx	\
+	FADS823		IVMS8_128	NETVIA_V2	SXNI855T	\
+	FADS850SAR	IVMS8_256	NX823		TOP860		\
+	FADS860T	KUP4K		pcu_e		TQM823L		\
+	FLAGADM		KUP4X		QS823		TQM823L_LCD	\
+	FPS850L		LANTEC		QS850		TQM850L		\
+	GEN860T		lwmon		QS860T		TQM855L		\
+	GEN860T_SC	MBX		quantum		TQM860L		\
+							v37		\
 "
 
 #########################################################################
@@ -99,7 +100,8 @@ LIST_8260="	\
 #########################################################################
 
 LIST_85xx="	\
-	MPC8540ADS	MPC8560ADS	sbc8560		stxgp3		\
+	MPC8540ADS	MPC8541CDS	MPC8555CDS	MPC8560ADS	\
+	sbc8540		sbc8560		stxgp3				\
 "
 
 #########################################################################
@@ -139,17 +141,22 @@ LIST_ARM7="B2 ep7312 evb4510 impa7 modnet50"
 #########################################################################
 
 LIST_ARM9="	\
-	at91rm9200dk	integratorcp	integratorap 	lpd7a400	\
-	mx1ads		mx1fs2		omap1510inn	omap1610h2	\
-	omap1610inn	omap730p2	scb9328		smdk2400	\
-	smdk2410	trab		VCMA9		versatile	\
+	at91rm9200dk	cmc_pu2		integratorcp	integratorap 	\
+	lpd7a400	mx1ads		mx1fs2		omap1510inn	\
+	omap1610h2	omap1610inn	omap730p2	scb9328		\
+	smdk2400	smdk2410	trab		VCMA9		\
+	versatile							\
 "
 
 #########################################################################
 ## Xscale Systems
 #########################################################################
 
-LIST_pxa="cerf250 cradle csb226 innokom lubbock wepep250 xm250 xsengine"
+LIST_pxa="	\
+	cerf250		cradle		csb226		innokom		\
+	lubbock		wepep250	xaeniax		xm250		\
+	xsengine							\
+"
 
 LIST_ixp="ixdp425"
 
@@ -187,6 +194,12 @@ LIST_nios="	\
 	DK1S10 DK1S10_standard_32 DK1S10_mtx_ldk_20			\
 "
 
+#########################################################################
+## Nios-II Systems
+#########################################################################
+
+LIST_nios2="PCI5441 PK1C20"
+
 #########################################################################
 ## MicroBlaze Systems
 #########################################################################
@@ -219,7 +232,7 @@ do
 	arm|SA|ARM7|ARM9|pxa|ixp| \
 	microblaze| \
 	mips| \
-	nios| \
+	nios|nios2| \
 	x86|I486)
 			for target in `eval echo '$LIST_'${arg}`
 			do

Makefile

@@ -45,7 +45,7 @@ export	TOPDIR
 ifeq (include/config.mk,$(wildcard include/config.mk))
 # load ARCH, BOARD, and CPU configuration
 include include/config.mk
-export	ARCH CPU BOARD VENDOR
+export	ARCH CPU BOARD VENDOR SOC
 # load other configuration
 include $(TOPDIR)/config.mk
 
@@ -72,6 +72,9 @@ endif
 ifeq ($(ARCH),nios)
 CROSS_COMPILE = nios-elf-
 endif
+ifeq ($(ARCH),nios2)
+CROSS_COMPILE = nios2-elf-
+endif
 ifeq ($(ARCH),m68k)
 CROSS_COMPILE = m68k-elf-
 endif
@@ -101,6 +104,9 @@ endif
 LIBS  = lib_generic/libgeneric.a
 LIBS += board/$(BOARDDIR)/lib$(BOARD).a
 LIBS += cpu/$(CPU)/lib$(CPU).a
+ifdef SOC
+LIBS += cpu/$(CPU)/$(SOC)/lib$(SOC).a
+endif
 LIBS += lib_$(ARCH)/lib$(ARCH).a
 LIBS += fs/cramfs/libcramfs.a fs/fat/libfat.a fs/fdos/libfdos.a fs/jffs2/libjffs2.a \
 	fs/reiserfs/libreiserfs.a
@@ -553,6 +559,9 @@ QS823_config:	unconfig
 QS860T_config:	unconfig
 	@./mkconfig $(@:_config=) ppc mpc8xx qs860t snmc
 
+quantum_config:	unconfig
+	@./mkconfig $(@:_config=) ppc mpc8xx quantum
+
 R360MPI_config:	unconfig
 	@./mkconfig $(@:_config=) ppc mpc8xx r360mpi
 
@@ -680,9 +689,19 @@ BUBINGA405EP_config:	unconfig
 CANBT_config:	unconfig
 	@./mkconfig $(@:_config=) ppc ppc4xx canbt esd
 
-CATcenter_config:	unconfig
+CATcenter_config	\
+CATcenter_25_config	\
+CATcenter_33_config:	unconfig
 	@ echo "/* CATcenter uses PPChameleon Model ME */"  > include/config.h
 	@ echo "#define CONFIG_PPCHAMELEON_MODULE_MODEL 1" >> include/config.h
+	@[ -z "$(findstring _25,$@)" ] || \
+		{ echo "#define CONFIG_PPCHAMELEON_CLK_25" >>include/config.h ; \
+		  echo "SysClk = 25MHz" ; \
+		}
+	@[ -z "$(findstring _33,$@)" ] || \
+		{ echo "#define CONFIG_PPCHAMELEON_CLK_33" >>include/config.h ; \
+		  echo "SysClk = 33MHz" ; \
+		}
 	@./mkconfig -a $(call xtract_4xx,$@) ppc ppc4xx PPChameleonEVB dave
 
 CPCI405_config	\
@@ -771,25 +790,25 @@ PPChameleonEVB_BA_33_config	\
 PPChameleonEVB_ME_33_config	\
 PPChameleonEVB_HI_33_config:	unconfig
 	@ >include/config.h
-	@[ -z "$(findstring _MODEL_BA,$@)" ] || \
+	@[ -z "$(findstring EVB_BA,$@)" ] || \
 		{ echo "#define CONFIG_PPCHAMELEON_MODULE_MODEL 0" >>include/config.h ; \
 		  echo "... BASIC model" ; \
 		}
-	@[ -z "$(findstring _MODEL_ME,$@)" ] || \
+	@[ -z "$(findstring EVB_ME,$@)" ] || \
 		{ echo "#define CONFIG_PPCHAMELEON_MODULE_MODEL 1" >>include/config.h ; \
 		  echo "... MEDIUM model" ; \
 		}
-	@[ -z "$(findstring _MODEL_HI,$@)" ] || \
+	@[ -z "$(findstring EVB_HI,$@)" ] || \
 		{ echo "#define CONFIG_PPCHAMELEON_MODULE_MODEL 2" >>include/config.h ; \
 		  echo "... HIGH-END model" ; \
 		}
 	@[ -z "$(findstring _25,$@)" ] || \
 		{ echo "#define CONFIG_PPCHAMELEON_CLK_25" >>include/config.h ; \
-		  echo " SysClk = 25MHz" ; \
+		  echo "SysClk = 25MHz" ; \
 		}
 	@[ -z "$(findstring _33,$@)" ] || \
 		{ echo "#define CONFIG_PPCHAMELEON_CLK_33" >>include/config.h ; \
-		  echo " SysClk = 33MHz" ; \
+		  echo "SysClk = 33MHz" ; \
 		}
 	@./mkconfig -a $(call xtract_4xx,$@) ppc ppc4xx PPChameleonEVB dave
 
@@ -1071,14 +1090,29 @@ MPC8540ADS_config:	unconfig
 MPC8560ADS_config:	unconfig
 	@./mkconfig $(@:_config=) ppc mpc85xx mpc8560ads
 
-stxgp3_config:		unconfig
-	@./mkconfig $(@:_config=) ppc mpc85xx stxgp3
+MPC8541CDS_config:	unconfig
+	@./mkconfig $(@:_config=) ppc mpc85xx mpc8541cds cds
+
+MPC8555CDS_config:	unconfig
+	@./mkconfig $(@:_config=) ppc mpc85xx mpc8555cds cds
+
+sbc8540_config \
+sbc8540_33_config \
+sbc8540_66_config:	unconfig
+	@if [ "$(findstring _66_,$@)" ] ; then \
+		echo "#define CONFIG_PCI_66"	>>include/config.h ; \
+		echo "... 66 MHz PCI" ; \
+	else \
+		>include/config.h ; \
+		echo "... 33 MHz PCI" ; \
+	fi
+	@./mkconfig -a SBC8540 ppc mpc85xx sbc8560
 
 sbc8560_config \
 sbc8560_33_config \
 sbc8560_66_config:      unconfig
 	@if [ "$(findstring _66_,$@)" ] ; then \
-		echo "#define CONFIG_PCI_66"  >>include/config.h ; \
+		echo "#define CONFIG_PCI_66"	>>include/config.h ; \
 		echo "... 66 MHz PCI" ; \
 	else \
 		>include/config.h ; \
@@ -1086,6 +1120,9 @@ sbc8560_66_config:      unconfig
 	fi
 	@./mkconfig -a sbc8560 ppc mpc85xx sbc8560
 
+stxgp3_config:		unconfig
+	@./mkconfig $(@:_config=) ppc mpc85xx stxgp3
+
 #########################################################################
 ## 74xx/7xx Systems
 #########################################################################
@@ -1162,10 +1199,10 @@ lpd7a404_config:	unconfig
 	@./mkconfig $(@:_config=) arm lh7a40x lpd7a40x
 
 mx1ads_config	:	unconfig
-	@./mkconfig $(@:_config=) arm arm920t mx1ads
+	@./mkconfig $(@:_config=) arm arm920t mx1ads NULL imx
 
 mx1fs2_config	:	unconfig
-	@./mkconfig $(@:_config=) arm arm920t mx1fs2
+	@./mkconfig $(@:_config=) arm arm920t mx1fs2 NULL imx
 
 omap1510inn_config :	unconfig
 	@./mkconfig $(@:_config=) arm arm925t omap1510inn
@@ -1206,13 +1243,13 @@ omap730p2_cs3boot_config :	unconfig
 	@./mkconfig -a $(call xtract_omap730p2,$@) arm arm926ejs omap730p2
 
 scb9328_config	:	unconfig
-	@./mkconfig $(@:_config=) arm arm920t scb9328
+	@./mkconfig $(@:_config=) arm arm920t scb9328 NULL imx
 
 smdk2400_config	:	unconfig
-	@./mkconfig $(@:_config=) arm arm920t smdk2400
+	@./mkconfig $(@:_config=) arm arm920t smdk2400 NULL s3c24x0
 
 smdk2410_config	:	unconfig
-	@./mkconfig $(@:_config=) arm arm920t smdk2410
+	@./mkconfig $(@:_config=) arm arm920t smdk2410 NULL s3c24x0
 
 SX1_config :		unconfig
 	@./mkconfig $(@:_config=) arm arm925t sx1
@@ -1240,10 +1277,10 @@ trab_old_config:	unconfig
 		  echo "... with 8 MB Flash, 16 MB RAM" ; \
 		  echo "TEXT_BASE = 0x0CF40000" >board/trab/config.tmp ; \
 		}
-	@./mkconfig -a $(call xtract_trab,$@) arm arm920t trab
+	@./mkconfig -a $(call xtract_trab,$@) arm arm920t trab NULL s3c24x0
 
 VCMA9_config	:	unconfig
-	@./mkconfig $(@:_config=) arm arm920t vcma9 mpl
+	@./mkconfig $(@:_config=) arm arm920t vcma9 mpl s3c24x0
 
 versatile_config :	unconfig
 	@./mkconfig $(@:_config=) arm arm926ejs versatile
@@ -1278,6 +1315,9 @@ evb4510_config :	unconfig
 at91rm9200dk_config	:	unconfig
 	@./mkconfig $(@:_config=) arm at91rm9200 at91rm9200dk
 
+cmc_pu2_config	:	unconfig
+	@./mkconfig $(@:_config=) arm at91rm9200 cmc_pu2
+
 #########################################################################
 ## XScale Systems
 #########################################################################
@@ -1306,6 +1346,9 @@ logodl_config	:	unconfig
 wepep250_config	:	unconfig
 	@./mkconfig $(@:_config=) arm pxa wepep250
 
+xaeniax_config	:	unconfig
+	@./mkconfig $(@:_config=) arm pxa xaeniax
+
 xm250_config	:	unconfig
 	@./mkconfig $(@:_config=) arm pxa xm250
 
@@ -1449,6 +1492,15 @@ ADNPESC1_config: unconfig
 		}
 	@./mkconfig -a ADNPESC1 nios nios adnpesc1 ssv
 
+#########################################################################
+## Nios-II
+#########################################################################
+
+PK1C20_config : unconfig
+	@./mkconfig  PK1C20 nios2 nios2 pk1c20 psyent
+
+PCI5441_config : unconfig
+	@./mkconfig  PCI5441 nios2 nios2 pci5441 psyent
 
 #========================================================================
 # MicroBlaze

README

@@ -125,6 +125,8 @@ Directory Hierarchy:
   - 74xx_7xx	Files specific to Motorola MPC74xx and 7xx CPUs
   - arm720t	Files specific to ARM 720 CPUs
   - arm920t	Files specific to ARM 920 CPUs
+    - imx	Files specific to Motorola MC9328 i.MX CPUs
+    - s3c24x0	Files specific to Samsung S3C24X0 CPUs
   - arm925t	Files specific to ARM 925 CPUs
   - arm926ejs	Files specific to ARM 926 CPUs
   - at91rm9200	Files specific to Atmel AT91RM9200 CPUs
@@ -139,6 +141,7 @@ Directory Hierarchy:
   - mpc8260	Files specific to Motorola MPC8260 CPUs
   - mpc85xx	Files specific to Motorola MPC85xx CPUs
   - nios	Files specific to Altera NIOS CPUs
+  - nios2	Files specific to Altera Nios-II CPUs
   - ppc4xx	Files specific to IBM PowerPC 4xx CPUs
   - pxa		Files specific to Intel XScale PXA CPUs
   - s3c44b0	Files specific to Samsung S3C44B0 CPUs
@@ -244,6 +247,10 @@ The following options need to be configured:
 		----------------------
 		CONFIG_MICROBLAZE
 
+		Nios-2 based CPUs:
+		----------------------
+		CONFIG_NIOS2
+
 
 - Board Type:	Define exactly one of
 
@@ -304,6 +311,11 @@ The following options need to be configured:
 
 		CONFIG_SUZAKU
 
+		Nios-2 based boards:
+		------------------------
+
+		CONFIG_PCI5441 CONFIG_PK1C20
+
 
 - CPU Module Type: (if CONFIG_COGENT is defined)
 		Define exactly one of
@@ -339,16 +351,17 @@ The following options need to be configured:
 		CONFIG_MPC8240, CONFIG_MPC8245
 
 - 8xx CPU Options: (if using an MPC8xx cpu)
-		Define one or more of
-		CONFIG_8xx_GCLK_FREQ	- if get_gclk_freq() cannot work
+		CONFIG_8xx_GCLK_FREQ	- deprecated: CPU clock if
+					  get_gclk_freq() cannot work
 					  e.g. if there is no 32KHz
 					  reference PIT/RTC clock
+		CONFIG_8xx_OSCLK	- PLL input clock (either EXTCLK
+					  or XTAL/EXTAL)
 
-- 859/866 CPU options: (if using a MPC859 or MPC866 CPU):
-		CFG_866_OSCCLK
-		CFG_866_CPUCLK_MIN
-		CFG_866_CPUCLK_MAX
-		CFG_866_CPUCLK_DEFAULT
+- 859/866/885 CPU options: (if using a MPC859 or MPC866 or MPC885 CPU):
+		CFG_8xx_CPUCLK_MIN
+		CFG_8xx_CPUCLK_MAX
+		CONFIG_8xx_CPUCLK_DEFAULT
 			See doc/README.MPC866
 
 		CFG_MEASURE_CPUCLK
@@ -358,7 +371,7 @@ The following options need to be configured:
 		values. Mostly useful for board bringup to make sure
 		the PLL is locked at the intended frequency. Note
 		that this requires a (stable) reference clock (32 kHz
-		RTC clock),
+		RTC clock or CFG_8XX_XIN)
 
 - Linux Kernel Interface:
 		CONFIG_CLOCKS_IN_MHZ
@@ -784,7 +797,7 @@ The following options need to be configured:
 		supported (PIP405, MIP405, MPC5200); define
 		CONFIG_USB_UHCI to enable it.
 		define CONFIG_USB_KEYBOARD to enable the USB Keyboard
-		end define CONFIG_USB_STORAGE to enable the USB
+		and define CONFIG_USB_STORAGE to enable the USB
 		storage devices.
 		Note:
 		Supported are USB Keyboards and USB Floppy drives

board/assabet/assabet.c

@@ -101,7 +101,7 @@ board_init(void)
 {
 	DECLARE_GLOBAL_DATA_PTR;
 
-	gd->bd->bi_arch_number = 25;	/* Intel Assabet Board */
+	gd->bd->bi_arch_number = MACH_TYPE_ASSABET;
 	gd->bd->bi_boot_params = 0xc0000100;
 
 	neponset_init();

board/at91rm9200dk/at91rm9200dk.c

@@ -45,7 +45,7 @@ int board_init (void)
 	/* so we do _nothing_ here */
 
 	/* arch number of AT91RM9200DK-Board */
-	gd->bd->bi_arch_number = 251;
+	gd->bd->bi_arch_number = MACH_TYPE_AT91RM9200;
 	/* adress of boot parameters */
 	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
 

board/cds/common/cadmus.c

@@ -0,0 +1,95 @@
+/*
+ * Copyright 2004 Freescale Semiconductor.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+
+#include <common.h>
+
+
+/*
+ * CADMUS Board System Registers
+ */
+#ifndef CFG_CADMUS_BASE_REG
+#define CFG_CADMUS_BASE_REG	(CADMUS_BASE_ADDR + 0x4000)
+#endif
+
+typedef struct cadmus_reg {
+    u_char cm_ver;		/* Board version */
+    u_char cm_csr;		/* General control/status */
+    u_char cm_rst;		/* Reset control */
+    u_char cm_hsclk;		/* High speed clock */
+    u_char cm_hsxclk;		/* High speed clock extended */
+    u_char cm_led;		/* LED data */
+    u_char cm_pci;		/* PCI control/status */
+    u_char cm_dma;		/* DMA control */
+    u_char cm_reserved[248];	/* Total 256 bytes */
+} cadmus_reg_t;
+
+
+unsigned int
+get_board_version(void)
+{
+	volatile cadmus_reg_t *cadmus = (cadmus_reg_t *)CFG_CADMUS_BASE_REG;
+
+	return cadmus->cm_ver;
+}
+
+
+unsigned long
+get_clock_freq(void)
+{
+	volatile cadmus_reg_t *cadmus = (cadmus_reg_t *)CFG_CADMUS_BASE_REG;
+
+	uint pci1_speed = (cadmus->cm_pci >> 2) & 0x3; /* PSPEED in [4:5] */
+
+	if (pci1_speed == 0) {
+		return 33000000;
+	} else if (pci1_speed == 1) {
+		return 66000000;
+	} else {
+		/* Really, unknown. Be safe? */
+		return 33000000;
+	}
+}
+
+
+unsigned int
+get_pci_slot(void)
+{
+	volatile cadmus_reg_t *cadmus = (cadmus_reg_t *)CFG_CADMUS_BASE_REG;
+
+	/*
+	 * PCI slot in USER bits CSR[6:7] by convention.
+	 */
+	return ((cadmus->cm_csr >> 6) & 0x3) + 1;
+}
+
+
+unsigned int
+get_pci_dual(void)
+{
+	volatile cadmus_reg_t *cadmus = (cadmus_reg_t *)CFG_CADMUS_BASE_REG;
+
+	/*
+	 * PCI DUAL in CM_PCI[3]
+	 */
+	return cadmus->cm_pci & 0x10;
+}

board/cds/common/cadmus.h

@@ -0,0 +1,54 @@
+/*
+ * Copyright 2004 Freescale Semiconductor.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CADMUS_H_
+#define __CADMUS_H_
+
+
+/*
+ * CADMUS Board System Register interface.
+ */
+
+/*
+ * Returns board version register.
+ */
+extern unsigned int get_board_version(void);
+
+/*
+ * Returns either 33000000 or 66000000 as the SYS_CLK_FREQ.
+ */
+extern unsigned long get_clock_freq(void);
+
+
+/*
+ * Returns 1 - 4, as found in the USER CSR[6:7] bits.
+ */
+extern unsigned int get_pci_slot(void);
+
+
+/*
+ * Returns PCI DUAL as found in CM_PCI[3].
+ */
+extern unsigned int get_pci_dual(void);
+
+
+#endif	/* __CADMUS_H_ */

board/cds/common/eeprom.c

@@ -0,0 +1,60 @@
+/*
+ * Copyright 2004 Freescale Semiconductor.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+
+#include <common.h>
+#include <i2c.h>
+
+#include "eeprom.h"
+
+
+typedef struct {
+	char idee_pcbid[4];		/* "CCID" for CDC v1.X */
+	u8 idee_major;
+	u8 idee_minor;
+	char idee_serial[10];
+	char idee_errata[2];
+	char idee_date[8];		/* yyyymmdd */
+	/* The rest of the EEPROM space is reserved */
+} id_eeprom_t;
+
+
+unsigned int
+get_cpu_board_revision(void)
+{
+	uint major = 0;
+	uint minor = 0;
+
+	id_eeprom_t id_eeprom;
+
+	i2c_read(CFG_I2C_EEPROM_ADDR, 0, 2,
+		 (uchar *) &id_eeprom, sizeof(id_eeprom));
+
+	major = id_eeprom.idee_major;
+	minor = id_eeprom.idee_minor;
+
+	if (major == 0xff && minor == 0xff) {
+		major = minor = 0;
+	}
+
+	return MPC85XX_CPU_BOARD_REV(major,minor);
+}

board/cds/common/eeprom.h

@@ -0,0 +1,50 @@
+/*
+ * Copyright 2004 Freescale Semiconductor.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __EEPROM_H_
+#define __EEPROM_H_
+
+
+/*
+ * EEPROM Board System Register interface.
+ */
+
+
+/*
+ * CPU Board Revision
+ */
+#define MPC85XX_CPU_BOARD_REV(maj, min)	((((maj)&0xff) << 8) | ((min) & 0xff))
+#define MPC85XX_CPU_BOARD_MAJOR(rev)	(((rev) >> 8) & 0xff)
+#define MPC85XX_CPU_BOARD_MINOR(rev)	((rev) & 0xff)
+
+#define MPC85XX_CPU_BOARD_REV_UNKNOWN	MPC85XX_CPU_BOARD_REV(0,0)
+#define MPC85XX_CPU_BOARD_REV_1_0	MPC85XX_CPU_BOARD_REV(1,0)
+#define MPC85XX_CPU_BOARD_REV_1_1	MPC85XX_CPU_BOARD_REV(1,1)
+
+/*
+ * Returns CPU board revision register as a 16-bit value with
+ * the Major in the high byte, and Minor in the low byte.
+ */
+extern unsigned int get_cpu_board_revision(void);
+
+
+#endif	/* __CADMUS_H_ */

board/cds/mpc8541cds/Makefile

@@ -0,0 +1,51 @@
+#
+# Copyright 2004 Freescale Semiconductor.
+# (C) Copyright 2001
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	:= $(BOARD).o \
+	   ../common/cadmus.o \
+	   ../common/eeprom.o
+
+SOBJS	:= init.o
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) crv $@ $(OBJS)
+
+clean:
+	rm -f $(OBJS) $(SOBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+-include .depend
+
+#########################################################################

board/cds/mpc8541cds/config.mk

@@ -0,0 +1,30 @@
+#
+# Copyright 2004 Freescale Semiconductor.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# mpc8541cds board
+#
+TEXT_BASE = 0xfff80000
+
+PLATFORM_CPPFLAGS += -DCONFIG_E500=1
+PLATFORM_CPPFLAGS += -DCONFIG_MPC85xx=1
+PLATFORM_CPPFLAGS += -DCONFIG_MPC8541=1

board/cds/mpc8541cds/init.S

@@ -0,0 +1,255 @@
+/*
+ * Copyright 2004 Freescale Semiconductor.
+ * Copyright 2002,2003, Motorola Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <ppc_asm.tmpl>
+#include <ppc_defs.h>
+#include <asm/cache.h>
+#include <asm/mmu.h>
+#include <config.h>
+#include <mpc85xx.h>
+
+
+/*
+ * TLB0 and TLB1 Entries
+ *
+ * Out of reset, TLB1's Entry 0 maps the highest 4K for CCSRBAR.
+ * However, CCSRBAR is then relocated to CFG_CCSRBAR right after
+ * these TLB entries are established.
+ *
+ * The TLB entries for DDR are dynamically setup in spd_sdram()
+ * and use TLB1 Entries 8 through 15 as needed according to the
+ * size of DDR memory.
+ *
+ * MAS0: tlbsel, esel, nv
+ * MAS1: valid, iprot, tid, ts, tsize
+ * MAS2: epn, sharen, x0, x1, w, i, m, g, e
+ * MAS3: rpn, u0-u3, ux, sx, uw, sw, ur, sr
+ */
+
+#define	entry_start \
+	mflr	r1 	;	\
+	bl	0f 	;
+
+#define	entry_end \
+0:	mflr	r0	;	\
+	mtlr	r1	;	\
+	blr		;
+
+
+	.section	.bootpg, "ax"
+	.globl	tlb1_entry
+tlb1_entry:
+	entry_start
+
+	/*
+	 * Number of TLB0 and TLB1 entries in the following table
+	 */
+	.long 13
+
+#if (CFG_CCSRBAR_DEFAULT != CFG_CCSRBAR)
+	/*
+	 * TLB0		4K	Non-cacheable, guarded
+	 * 0xff700000	4K	Initial CCSRBAR mapping
+	 *
+	 * This ends up at a TLB0 Index==0 entry, and must not collide
+	 * with other TLB0 Entries.
+	 */
+	.long TLB1_MAS0(0, 0, 0)
+	.long TLB1_MAS1(1, 0, 0, 0, 0)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,0,1,0,1,0,1)
+#else
+#error("Update the number of table entries in tlb1_entry")
+#endif
+
+	/*
+	 * TLB0		16K	Cacheable, non-guarded
+	 * 0xd001_0000	16K	Temporary Global data for initialization
+	 *
+	 * Use four 4K TLB0 entries.  These entries must be cacheable
+	 * as they provide the bootstrap memory before the memory
+	 * controler and real memory have been configured.
+	 *
+	 * These entries end up at TLB0 Indicies 0x10, 0x14, 0x18 and 0x1c,
+	 * and must not collide with other TLB0 entries.
+	 */
+	.long TLB1_MAS0(0, 0, 0)
+	.long TLB1_MAS1(1, 0, 0, 0, 0)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR),
+			0,0,0,0,0,0,0,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR),
+			0,0,0,0,0,1,0,1,0,1)
+
+	.long TLB1_MAS0(0, 0, 0)
+	.long TLB1_MAS1(1, 0, 0, 0, 0)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 4 * 1024),
+			0,0,0,0,0,0,0,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 4 * 1024),
+			0,0,0,0,0,1,0,1,0,1)
+
+	.long TLB1_MAS0(0, 0, 0)
+	.long TLB1_MAS1(1, 0, 0, 0, 0)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 8 * 1024),
+			0,0,0,0,0,0,0,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 8 * 1024),
+			0,0,0,0,0,1,0,1,0,1)
+
+	.long TLB1_MAS0(0, 0, 0)
+	.long TLB1_MAS1(1, 0, 0, 0, 0)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 12 * 1024),
+			0,0,0,0,0,0,0,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 12 * 1024),
+			0,0,0,0,0,1,0,1,0,1)
+
+
+	/*
+	 * TLB 0:	16M	Non-cacheable, guarded
+	 * 0xff000000	16M	FLASH
+	 * Out of reset this entry is only 4K.
+	 */
+	.long TLB1_MAS0(1, 0, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_FLASH_BASE), 0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_FLASH_BASE), 0,0,0,0,0,1,0,1,0,1)
+
+	/*
+	 * TLB 1:	256M	Non-cacheable, guarded
+	 * 0x80000000	256M	PCI1 MEM First half
+	 */
+	.long TLB1_MAS0(1, 1, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE), 0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE), 0,0,0,0,0,1,0,1,0,1)
+
+	/*
+	 * TLB 2:	256M	Non-cacheable, guarded
+	 * 0x90000000	256M	PCI1 MEM Second half
+	 */
+	.long TLB1_MAS0(1, 2, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE + 0x10000000),
+			0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE + 0x10000000),
+			0,0,0,0,0,1,0,1,0,1)
+
+	/*
+	 * TLB 3:	256M	Non-cacheable, guarded
+	 * 0xa0000000	256M	PCI2 MEM First half
+	 */
+	.long TLB1_MAS0(1, 3, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_PCI2_MEM_BASE), 0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_PCI2_MEM_BASE), 0,0,0,0,0,1,0,1,0,1)
+
+	/*
+	 * TLB 4:	256M	Non-cacheable, guarded
+	 * 0xb0000000	256M	PCI2 MEM Second half
+	 */
+	.long TLB1_MAS0(1, 4, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_PCI2_MEM_BASE + 0x10000000),
+			0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_PCI2_MEM_BASE + 0x10000000),
+			0,0,0,0,0,1,0,1,0,1)
+
+	/*
+	 * TLB 5:	64M	Non-cacheable, guarded
+	 * 0xe000_0000	1M	CCSRBAR
+	 * 0xe200_0000	16M	PCI1 IO
+	 * 0xe300_0000	16M	PCI2 IO
+	 */
+	.long TLB1_MAS0(1, 5, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR), 0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR), 0,0,0,0,0,1,0,1,0,1)
+
+	/*
+	 * TLB 6:	64M	Cacheable, non-guarded
+	 * 0xf000_0000	64M	LBC SDRAM
+	 */
+	.long TLB1_MAS0(1, 6, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_LBC_SDRAM_BASE), 0,0,0,0,0,0,0,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_LBC_SDRAM_BASE), 0,0,0,0,0,1,0,1,0,1)
+
+	/*
+	 * TLB 7:	1M	Non-cacheable, guarded
+	 * 0xf8000000	1M	CADMUS registers
+	 */
+	.long TLB1_MAS0(1, 7, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_1M)
+	.long TLB1_MAS2(E500_TLB_EPN(CADMUS_BASE_ADDR), 0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CADMUS_BASE_ADDR), 0,0,0,0,0,1,0,1,0,1)
+
+	entry_end
+
+/*
+ * LAW(Local Access Window) configuration:
+ *
+ * 0x0000_0000     0x7fff_ffff     DDR                     2G
+ * 0x8000_0000     0x9fff_ffff     PCI1 MEM                512M
+ * 0xa000_0000     0xbfff_ffff     PCI2 MEM                512M
+ * 0xe000_0000     0xe000_ffff     CCSR                    1M
+ * 0xe200_0000     0xe2ff_ffff     PCI1 IO                 16M
+ * 0xe300_0000     0xe3ff_ffff     PCI2 IO                 16M
+ * 0xf000_0000     0xf7ff_ffff     SDRAM                   128M
+ * 0xf800_0000     0xf80f_ffff     NVRAM/CADMUS (*)        1M
+ * 0xff00_0000     0xff7f_ffff     FLASH (2nd bank)        8M
+ * 0xff80_0000     0xffff_ffff     FLASH (boot bank)       8M
+ *
+ * Notes:
+ *    CCSRBAR and L2-as-SRAM don't need a configured Local Access Window.
+ *    If flash is 8M at default position (last 8M), no LAW needed.
+ *
+ * The defines below are 1-off of the actual LAWAR0 usage.
+ * So LAWAR3 define uses the LAWAR4 register in the ECM.
+ */
+
+#define LAWBAR0 0
+#define LAWAR0  ((LAWAR_TRGT_IF_DDR | (LAWAR_SIZE & LAWAR_SIZE_128M)) & ~LAWAR_EN)
+
+#define LAWBAR1 ((CFG_PCI1_MEM_BASE>>12) & 0xfffff)
+#define LAWAR1 	(LAWAR_EN | LAWAR_TRGT_IF_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_512M))
+
+#define LAWBAR2 ((CFG_PCI2_MEM_BASE>>12) & 0xfffff)
+#define LAWAR2 	(LAWAR_EN | LAWAR_TRGT_IF_PCI2 | (LAWAR_SIZE & LAWAR_SIZE_512M))
+
+#define LAWBAR3 ((CFG_PCI1_IO_BASE>>12) & 0xfffff)
+#define LAWAR3 	(LAWAR_EN | LAWAR_TRGT_IF_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_16M))
+
+#define LAWBAR4 ((CFG_PCI2_IO_BASE>>12) & 0xfffff)
+#define LAWAR4 	(LAWAR_EN | LAWAR_TRGT_IF_PCI2 | (LAWAR_SIZE & LAWAR_SIZE_16M))
+
+/* LBC window - maps 256M 0xf0000000 -> 0xffffffff */
+#define LAWBAR5 ((CFG_LBC_SDRAM_BASE>>12) & 0xfffff)
+#define LAWAR5 	(LAWAR_EN | LAWAR_TRGT_IF_LBC | (LAWAR_SIZE & LAWAR_SIZE_256M))
+
+	.section .bootpg, "ax"
+	.globl	law_entry
+
+law_entry:
+	entry_start
+	.long 6
+	.long LAWBAR0,LAWAR0,LAWBAR1,LAWAR1,LAWBAR2,LAWAR2,LAWBAR3,LAWAR3
+	.long LAWBAR4,LAWAR4,LAWBAR5,LAWAR5
+	entry_end

board/cds/mpc8541cds/mpc8541cds.c

@@ -0,0 +1,349 @@
+/*
+ * Copyright 2004 Freescale Semiconductor.
+ *
+ * (C) Copyright 2002 Scott McNutt <smcnutt@artesyncp.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <pci.h>
+#include <asm/processor.h>
+#include <asm/immap_85xx.h>
+#include <spd.h>
+
+#include "../common/cadmus.h"
+#include "../common/eeprom.h"
+
+#if defined(CONFIG_DDR_ECC)
+extern void ddr_enable_ecc(unsigned int dram_size);
+#endif
+
+extern long int spd_sdram(void);
+
+void local_bus_init(void);
+void sdram_init(void);
+
+int board_early_init_f (void)
+{
+	return 0;
+}
+
+int checkboard (void)
+{
+	volatile immap_t *immap = (immap_t *) CFG_CCSRBAR;
+	volatile ccsr_gur_t *gur = &immap->im_gur;
+
+	/* PCI slot in USER bits CSR[6:7] by convention. */
+	uint pci_slot = get_pci_slot ();
+
+	uint pci_dual = get_pci_dual ();	/* PCI DUAL in CM_PCI[3] */
+	uint pci1_32 = gur->pordevsr & 0x10000;	/* PORDEVSR[15] */
+	uint pci1_clk_sel = gur->porpllsr & 0x8000;	/* PORPLLSR[16] */
+	uint pci2_clk_sel = gur->porpllsr & 0x4000;	/* PORPLLSR[17] */
+
+	uint pci1_speed = get_clock_freq ();	/* PCI PSPEED in [4:5] */
+
+	uint cpu_board_rev = get_cpu_board_revision ();
+
+	printf ("Board: CDS Version 0x%02x, PCI Slot %d\n",
+		get_board_version (), pci_slot);
+
+	printf ("CPU Board Revision %d.%d (0x%04x)\n",
+		MPC85XX_CPU_BOARD_MAJOR (cpu_board_rev),
+		MPC85XX_CPU_BOARD_MINOR (cpu_board_rev), cpu_board_rev);
+
+	printf ("    PCI1: %d bit, %s MHz, %s\n",
+		(pci1_32) ? 32 : 64,
+		(pci1_speed == 33000000) ? "33" :
+		(pci1_speed == 66000000) ? "66" : "unknown",
+		pci1_clk_sel ? "sync" : "async");
+
+	if (pci_dual) {
+		printf ("    PCI2: 32 bit, 66 MHz, %s\n",
+			pci2_clk_sel ? "sync" : "async");
+	} else {
+		printf ("    PCI2: disabled\n");
+	}
+
+	/*
+	 * Initialize local bus.
+	 */
+	local_bus_init ();
+
+	return 0;
+}
+
+long int
+initdram(int board_type)
+{
+	long dram_size = 0;
+	volatile immap_t *immap = (immap_t *)CFG_IMMR;
+
+	puts("Initializing\n");
+
+#if defined(CONFIG_DDR_DLL)
+	{
+		/*
+		 * Work around to stabilize DDR DLL MSYNC_IN.
+		 * Errata DDR9 seems to have been fixed.
+		 * This is now the workaround for Errata DDR11:
+		 *    Override DLL = 1, Course Adj = 1, Tap Select = 0
+		 */
+
+		volatile ccsr_gur_t *gur= &immap->im_gur;
+
+		gur->ddrdllcr = 0x81000000;
+		asm("sync;isync;msync");
+		udelay(200);
+	}
+#endif
+	dram_size = spd_sdram();
+
+#if defined(CONFIG_DDR_ECC)
+	/*
+	 * Initialize and enable DDR ECC.
+	 */
+	ddr_enable_ecc(dram_size);
+#endif
+	/*
+	 * SDRAM Initialization
+	 */
+	sdram_init();
+
+	puts("    DDR: ");
+	return dram_size;
+}
+
+/*
+ * Initialize Local Bus
+ */
+void
+local_bus_init(void)
+{
+	volatile immap_t *immap = (immap_t *)CFG_IMMR;
+	volatile ccsr_gur_t *gur = &immap->im_gur;
+	volatile ccsr_lbc_t *lbc = &immap->im_lbc;
+
+	uint clkdiv;
+	uint lbc_hz;
+	sys_info_t sysinfo;
+	uint temp_lbcdll;
+
+	/*
+	 * Errata LBC11.
+	 * Fix Local Bus clock glitch when DLL is enabled.
+	 *
+	 * If localbus freq is < 66Mhz, DLL bypass mode must be used.
+	 * If localbus freq is > 133Mhz, DLL can be safely enabled.
+	 * Between 66 and 133, the DLL is enabled with an override workaround.
+	 */
+
+	get_sys_info(&sysinfo);
+	clkdiv = lbc->lcrr & 0x0f;
+	lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv;
+
+	if (lbc_hz < 66) {
+		lbc->lcrr |= 0x80000000;	/* DLL Bypass */
+
+	} else if (lbc_hz >= 133) {
+		lbc->lcrr &= (~0x80000000);		/* DLL Enabled */
+
+	} else {
+		lbc->lcrr &= (~0x8000000);	/* DLL Enabled */
+		udelay(200);
+
+		/*
+		 * Sample LBC DLL ctrl reg, upshift it to set the
+		 * override bits.
+		 */
+		temp_lbcdll = gur->lbcdllcr;
+		gur->lbcdllcr = (((temp_lbcdll & 0xff) << 16) | 0x80000000);
+		asm("sync;isync;msync");
+	}
+}
+
+/*
+ * Initialize SDRAM memory on the Local Bus.
+ */
+void
+sdram_init(void)
+{
+#if defined(CFG_OR2_PRELIM) && defined(CFG_BR2_PRELIM)
+
+	uint idx;
+	volatile immap_t *immap = (immap_t *)CFG_IMMR;
+	volatile ccsr_lbc_t *lbc = &immap->im_lbc;
+	uint *sdram_addr = (uint *)CFG_LBC_SDRAM_BASE;
+	uint cpu_board_rev;
+	uint lsdmr_common;
+
+	puts("    SDRAM: ");
+
+	print_size (CFG_LBC_SDRAM_SIZE * 1024 * 1024, "\n");
+
+	/*
+	 * Setup SDRAM Base and Option Registers
+	 */
+	lbc->or2 = CFG_OR2_PRELIM;
+	asm("msync");
+
+	lbc->br2 = CFG_BR2_PRELIM;
+	asm("msync");
+
+	lbc->lbcr = CFG_LBC_LBCR;
+	asm("msync");
+
+
+	lbc->lsrt = CFG_LBC_LSRT;
+	lbc->mrtpr = CFG_LBC_MRTPR;
+	asm("msync");
+
+	/*
+	 * Determine which address lines to use baed on CPU board rev.
+	 */
+	cpu_board_rev = get_cpu_board_revision();
+	lsdmr_common = CFG_LBC_LSDMR_COMMON;
+	if (cpu_board_rev == MPC85XX_CPU_BOARD_REV_1_0) {
+		lsdmr_common |= CFG_LBC_LSDMR_BSMA1617;
+	} else if (cpu_board_rev == MPC85XX_CPU_BOARD_REV_1_1) {
+		lsdmr_common |= CFG_LBC_LSDMR_BSMA1516;
+	} else {
+		/*
+		 * Assume something unable to identify itself is
+		 * really old, and likely has lines 16/17 mapped.
+		 */
+		lsdmr_common |= CFG_LBC_LSDMR_BSMA1617;
+	}
+
+	/*
+	 * Issue PRECHARGE ALL command.
+	 */
+	lbc->lsdmr = lsdmr_common | CFG_LBC_LSDMR_OP_PCHALL;
+	asm("sync;msync");
+	*sdram_addr = 0xff;
+	ppcDcbf((unsigned long) sdram_addr);
+	udelay(100);
+
+	/*
+	 * Issue 8 AUTO REFRESH commands.
+	 */
+	for (idx = 0; idx < 8; idx++) {
+		lbc->lsdmr = lsdmr_common | CFG_LBC_LSDMR_OP_ARFRSH;
+		asm("sync;msync");
+		*sdram_addr = 0xff;
+		ppcDcbf((unsigned long) sdram_addr);
+		udelay(100);
+	}
+
+	/*
+	 * Issue 8 MODE-set command.
+	 */
+	lbc->lsdmr = lsdmr_common | CFG_LBC_LSDMR_OP_MRW;
+	asm("sync;msync");
+	*sdram_addr = 0xff;
+	ppcDcbf((unsigned long) sdram_addr);
+	udelay(100);
+
+	/*
+	 * Issue NORMAL OP command.
+	 */
+	lbc->lsdmr = lsdmr_common | CFG_LBC_LSDMR_OP_NORMAL;
+	asm("sync;msync");
+	*sdram_addr = 0xff;
+	ppcDcbf((unsigned long) sdram_addr);
+	udelay(200);    /* Overkill. Must wait > 200 bus cycles */
+
+#endif	/* enable SDRAM init */
+}
+
+#if defined(CFG_DRAM_TEST)
+int
+testdram(void)
+{
+	uint *pstart = (uint *) CFG_MEMTEST_START;
+	uint *pend = (uint *) CFG_MEMTEST_END;
+	uint *p;
+
+	printf("Testing DRAM from 0x%08x to 0x%08x\n",
+	       CFG_MEMTEST_START,
+	       CFG_MEMTEST_END);
+
+	printf("DRAM test phase 1:\n");
+	for (p = pstart; p < pend; p++)
+		*p = 0xaaaaaaaa;
+
+	for (p = pstart; p < pend; p++) {
+		if (*p != 0xaaaaaaaa) {
+			printf ("DRAM test fails at: %08x\n", (uint) p);
+			return 1;
+		}
+	}
+
+	printf("DRAM test phase 2:\n");
+	for (p = pstart; p < pend; p++)
+		*p = 0x55555555;
+
+	for (p = pstart; p < pend; p++) {
+		if (*p != 0x55555555) {
+			printf ("DRAM test fails at: %08x\n", (uint) p);
+			return 1;
+		}
+	}
+
+	printf("DRAM test passed.\n");
+	return 0;
+}
+#endif
+
+#if defined(CONFIG_PCI)
+
+/*
+ * Initialize PCI Devices, report devices found.
+ */
+
+#ifndef CONFIG_PCI_PNP
+static struct pci_config_table pci_mpc85xxcds_config_table[] = {
+    { PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
+      PCI_IDSEL_NUMBER, PCI_ANY_ID,
+      pci_cfgfunc_config_device, { PCI_ENET0_IOADDR,
+				   PCI_ENET0_MEMADDR,
+				   PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER
+      } },
+    { }
+};
+#endif
+
+static struct pci_controller hose = {
+#ifndef CONFIG_PCI_PNP
+	config_table: pci_mpc85xxcds_config_table,
+#endif
+};
+
+#endif	/* CONFIG_PCI */
+
+void
+pci_init_board(void)
+{
+#ifdef CONFIG_PCI
+	extern void pci_mpc85xx_init(struct pci_controller *hose);
+
+	pci_mpc85xx_init(&hose);
+#endif
+}

board/cds/mpc8541cds/u-boot.lds

@@ -0,0 +1,147 @@
+/*
+ * Copyright 2004 Freescale Semiconductor.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+/* Do we need any of these for elf?
+   __DYNAMIC = 0;    */
+SECTIONS
+{
+  .resetvec 0xFFFFFFFC :
+  {
+    *(.resetvec)
+  } = 0xffff
+
+  .bootpg 0xFFFFF000 :
+  {
+    cpu/mpc85xx/start.o	(.bootpg)
+    board/cds/mpc8541cds/init.o (.bootpg)
+  } = 0xffff
+
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)		}
+  .rela.text     : { *(.rela.text) 	}
+  .rel.data      : { *(.rel.data)		}
+  .rela.data     : { *(.rela.data) 	}
+  .rel.rodata    : { *(.rel.rodata) 	}
+  .rela.rodata   : { *(.rela.rodata) 	}
+  .rel.got       : { *(.rel.got)		}
+  .rela.got      : { *(.rela.got)		}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)		}
+  .rela.bss      : { *(.rela.bss)		}
+  .rel.plt       : { *(.rel.plt)		}
+  .rela.plt      : { *(.rela.plt)		}
+  .init          : { *(.init)	}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    cpu/mpc85xx/start.o	(.text)
+    board/cds/mpc8541cds/init.o (.text)
+    cpu/mpc85xx/traps.o (.text)
+    cpu/mpc85xx/interrupts.o (.text)
+    cpu/mpc85xx/cpu_init.o (.text)
+    cpu/mpc85xx/cpu.o (.text)
+    cpu/mpc85xx/tsec.o (.text)
+    cpu/mpc85xx/speed.o (.text)
+    cpu/mpc85xx/pci.o (.text)
+    common/dlmalloc.o (.text)
+    lib_generic/crc32.o (.text)
+    lib_ppc/extable.o (.text)
+    lib_generic/zlib.o (.text)
+    *(.text)
+    *(.fixup)
+    *(.got1)
+   }
+    _etext = .;
+    PROVIDE (etext = .);
+    .rodata    :
+   {
+    *(.rodata)
+    *(.rodata1)
+    *(.rodata.str1.4)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x00FF) & 0xFFFFFF00;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2;
+  __fixup_entries = (. - _FIXUP_TABLE_) >> 2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  __u_boot_cmd_start = .;
+  .u_boot_cmd : { *(.u_boot_cmd) }
+  __u_boot_cmd_end = .;
+
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(256);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(256);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+  _end = . ;
+  PROVIDE (end = .);
+}

board/cds/mpc8555cds/Makefile

@@ -0,0 +1,51 @@
+#
+# Copyright 2004 Freescale Semiconductor.
+# (C) Copyright 2001
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	:= $(BOARD).o \
+	   ../common/cadmus.o \
+	   ../common/eeprom.o
+
+SOBJS	:= init.o
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) crv $@ $(OBJS)
+
+clean:
+	rm -f $(OBJS) $(SOBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+-include .depend
+
+#########################################################################

board/cds/mpc8555cds/config.mk

@@ -0,0 +1,30 @@
+#
+# Copyright 2004 Freescale Semiconductor.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# mpc8555cds board
+#
+TEXT_BASE = 0xfff80000
+
+PLATFORM_CPPFLAGS += -DCONFIG_E500=1
+PLATFORM_CPPFLAGS += -DCONFIG_MPC85xx=1
+PLATFORM_CPPFLAGS += -DCONFIG_MPC8555=1

board/cds/mpc8555cds/init.S

@@ -0,0 +1,255 @@
+/*
+ * Copyright 2004 Freescale Semiconductor.
+ * Copyright 2002,2003, Motorola Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <ppc_asm.tmpl>
+#include <ppc_defs.h>
+#include <asm/cache.h>
+#include <asm/mmu.h>
+#include <config.h>
+#include <mpc85xx.h>
+
+
+/*
+ * TLB0 and TLB1 Entries
+ *
+ * Out of reset, TLB1's Entry 0 maps the highest 4K for CCSRBAR.
+ * However, CCSRBAR is then relocated to CFG_CCSRBAR right after
+ * these TLB entries are established.
+ *
+ * The TLB entries for DDR are dynamically setup in spd_sdram()
+ * and use TLB1 Entries 8 through 15 as needed according to the
+ * size of DDR memory.
+ *
+ * MAS0: tlbsel, esel, nv
+ * MAS1: valid, iprot, tid, ts, tsize
+ * MAS2: epn, sharen, x0, x1, w, i, m, g, e
+ * MAS3: rpn, u0-u3, ux, sx, uw, sw, ur, sr
+ */
+
+#define	entry_start \
+	mflr	r1 	;	\
+	bl	0f 	;
+
+#define	entry_end \
+0:	mflr	r0	;	\
+	mtlr	r1	;	\
+	blr		;
+
+
+	.section	.bootpg, "ax"
+	.globl	tlb1_entry
+tlb1_entry:
+	entry_start
+
+	/*
+	 * Number of TLB0 and TLB1 entries in the following table
+	 */
+	.long 13
+
+#if (CFG_CCSRBAR_DEFAULT != CFG_CCSRBAR)
+	/*
+	 * TLB0		4K	Non-cacheable, guarded
+	 * 0xff700000	4K	Initial CCSRBAR mapping
+	 *
+	 * This ends up at a TLB0 Index==0 entry, and must not collide
+	 * with other TLB0 Entries.
+	 */
+	.long TLB1_MAS0(0, 0, 0)
+	.long TLB1_MAS1(1, 0, 0, 0, 0)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,0,1,0,1,0,1)
+#else
+#error("Update the number of table entries in tlb1_entry")
+#endif
+
+	/*
+	 * TLB0		16K	Cacheable, non-guarded
+	 * 0xd001_0000	16K	Temporary Global data for initialization
+	 *
+	 * Use four 4K TLB0 entries.  These entries must be cacheable
+	 * as they provide the bootstrap memory before the memory
+	 * controler and real memory have been configured.
+	 *
+	 * These entries end up at TLB0 Indicies 0x10, 0x14, 0x18 and 0x1c,
+	 * and must not collide with other TLB0 entries.
+	 */
+	.long TLB1_MAS0(0, 0, 0)
+	.long TLB1_MAS1(1, 0, 0, 0, 0)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR),
+			0,0,0,0,0,0,0,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR),
+			0,0,0,0,0,1,0,1,0,1)
+
+	.long TLB1_MAS0(0, 0, 0)
+	.long TLB1_MAS1(1, 0, 0, 0, 0)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 4 * 1024),
+			0,0,0,0,0,0,0,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 4 * 1024),
+			0,0,0,0,0,1,0,1,0,1)
+
+	.long TLB1_MAS0(0, 0, 0)
+	.long TLB1_MAS1(1, 0, 0, 0, 0)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 8 * 1024),
+			0,0,0,0,0,0,0,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 8 * 1024),
+			0,0,0,0,0,1,0,1,0,1)
+
+	.long TLB1_MAS0(0, 0, 0)
+	.long TLB1_MAS1(1, 0, 0, 0, 0)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 12 * 1024),
+			0,0,0,0,0,0,0,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 12 * 1024),
+			0,0,0,0,0,1,0,1,0,1)
+
+
+	/*
+	 * TLB 0:	16M	Non-cacheable, guarded
+	 * 0xff000000	16M	FLASH
+	 * Out of reset this entry is only 4K.
+	 */
+	.long TLB1_MAS0(1, 0, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_FLASH_BASE), 0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_FLASH_BASE), 0,0,0,0,0,1,0,1,0,1)
+
+	/*
+	 * TLB 1:	256M	Non-cacheable, guarded
+	 * 0x80000000	256M	PCI1 MEM First half
+	 */
+	.long TLB1_MAS0(1, 1, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE), 0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE), 0,0,0,0,0,1,0,1,0,1)
+
+	/*
+	 * TLB 2:	256M	Non-cacheable, guarded
+	 * 0x90000000	256M	PCI1 MEM Second half
+	 */
+	.long TLB1_MAS0(1, 2, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE + 0x10000000),
+			0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE + 0x10000000),
+			0,0,0,0,0,1,0,1,0,1)
+
+	/*
+	 * TLB 3:	256M	Non-cacheable, guarded
+	 * 0xa0000000	256M	PCI2 MEM First half
+	 */
+	.long TLB1_MAS0(1, 3, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_PCI2_MEM_BASE), 0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_PCI2_MEM_BASE), 0,0,0,0,0,1,0,1,0,1)
+
+	/*
+	 * TLB 4:	256M	Non-cacheable, guarded
+	 * 0xb0000000	256M	PCI2 MEM Second half
+	 */
+	.long TLB1_MAS0(1, 4, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_PCI2_MEM_BASE + 0x10000000),
+			0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_PCI2_MEM_BASE + 0x10000000),
+			0,0,0,0,0,1,0,1,0,1)
+
+	/*
+	 * TLB 5:	64M	Non-cacheable, guarded
+	 * 0xe000_0000	1M	CCSRBAR
+	 * 0xe200_0000	16M	PCI1 IO
+	 * 0xe300_0000	16M	PCI2 IO
+	 */
+	.long TLB1_MAS0(1, 5, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR), 0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR), 0,0,0,0,0,1,0,1,0,1)
+
+	/*
+	 * TLB 6:	64M	Cacheable, non-guarded
+	 * 0xf000_0000	64M	LBC SDRAM
+	 */
+	.long TLB1_MAS0(1, 6, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M)
+	.long TLB1_MAS2(E500_TLB_EPN(CFG_LBC_SDRAM_BASE), 0,0,0,0,0,0,0,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CFG_LBC_SDRAM_BASE), 0,0,0,0,0,1,0,1,0,1)
+
+	/*
+	 * TLB 7:	1M	Non-cacheable, guarded
+	 * 0xf8000000	1M	CADMUS registers
+	 */
+	.long TLB1_MAS0(1, 7, 0)
+	.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_1M)
+	.long TLB1_MAS2(E500_TLB_EPN(CADMUS_BASE_ADDR), 0,0,0,0,1,0,1,0)
+	.long TLB1_MAS3(E500_TLB_RPN(CADMUS_BASE_ADDR), 0,0,0,0,0,1,0,1,0,1)
+
+	entry_end
+
+/*
+ * LAW(Local Access Window) configuration:
+ *
+ * 0x0000_0000     0x7fff_ffff     DDR                     2G
+ * 0x8000_0000     0x9fff_ffff     PCI1 MEM                512M
+ * 0xa000_0000     0xbfff_ffff     PCI2 MEM                512M
+ * 0xe000_0000     0xe000_ffff     CCSR                    1M
+ * 0xe200_0000     0xe2ff_ffff     PCI1 IO                 16M
+ * 0xe300_0000     0xe3ff_ffff     PCI2 IO                 16M
+ * 0xf000_0000     0xf7ff_ffff     SDRAM                   128M
+ * 0xf800_0000     0xf80f_ffff     NVRAM/CADMUS (*)        1M
+ * 0xff00_0000     0xff7f_ffff     FLASH (2nd bank)        8M
+ * 0xff80_0000     0xffff_ffff     FLASH (boot bank)       8M
+ *
+ * Notes:
+ *    CCSRBAR and L2-as-SRAM don't need a configured Local Access Window.
+ *    If flash is 8M at default position (last 8M), no LAW needed.
+ *
+ * The defines below are 1-off of the actual LAWAR0 usage.
+ * So LAWAR3 define uses the LAWAR4 register in the ECM.
+ */
+
+#define LAWBAR0 0
+#define LAWAR0  ((LAWAR_TRGT_IF_DDR | (LAWAR_SIZE & LAWAR_SIZE_128M)) & ~LAWAR_EN)
+
+#define LAWBAR1 ((CFG_PCI1_MEM_BASE>>12) & 0xfffff)
+#define LAWAR1 	(LAWAR_EN | LAWAR_TRGT_IF_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_512M))
+
+#define LAWBAR2 ((CFG_PCI2_MEM_BASE>>12) & 0xfffff)
+#define LAWAR2 	(LAWAR_EN | LAWAR_TRGT_IF_PCI2 | (LAWAR_SIZE & LAWAR_SIZE_512M))
+
+#define LAWBAR3 ((CFG_PCI1_IO_BASE>>12) & 0xfffff)
+#define LAWAR3 	(LAWAR_EN | LAWAR_TRGT_IF_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_16M))
+
+#define LAWBAR4 ((CFG_PCI2_IO_BASE>>12) & 0xfffff)
+#define LAWAR4 	(LAWAR_EN | LAWAR_TRGT_IF_PCI2 | (LAWAR_SIZE & LAWAR_SIZE_16M))
+
+/* LBC window - maps 256M 0xf0000000 -> 0xffffffff */
+#define LAWBAR5 ((CFG_LBC_SDRAM_BASE>>12) & 0xfffff)
+#define LAWAR5 	(LAWAR_EN | LAWAR_TRGT_IF_LBC | (LAWAR_SIZE & LAWAR_SIZE_256M))
+
+	.section .bootpg, "ax"
+	.globl	law_entry
+
+law_entry:
+	entry_start
+	.long 6
+	.long LAWBAR0,LAWAR0,LAWBAR1,LAWAR1,LAWBAR2,LAWAR2,LAWBAR3,LAWAR3
+	.long LAWBAR4,LAWAR4,LAWBAR5,LAWAR5
+	entry_end

board/cds/mpc8555cds/mpc8555cds.c

@@ -0,0 +1,346 @@
+/*
+ * Copyright 2004 Freescale Semiconductor.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <pci.h>
+#include <asm/processor.h>
+#include <asm/immap_85xx.h>
+#include <spd.h>
+
+#include "../common/cadmus.h"
+#include "../common/eeprom.h"
+
+#if defined(CONFIG_DDR_ECC)
+extern void ddr_enable_ecc(unsigned int dram_size);
+#endif
+
+extern long int spd_sdram(void);
+
+void local_bus_init(void);
+void sdram_init(void);
+
+int board_early_init_f (void)
+{
+	return 0;
+}
+
+int checkboard (void)
+{
+	volatile immap_t *immap = (immap_t *) CFG_CCSRBAR;
+	volatile ccsr_gur_t *gur = &immap->im_gur;
+
+	/* PCI slot in USER bits CSR[6:7] by convention. */
+	uint pci_slot = get_pci_slot ();
+
+	uint pci_dual = get_pci_dual ();	/* PCI DUAL in CM_PCI[3] */
+	uint pci1_32 = gur->pordevsr & 0x10000;	/* PORDEVSR[15] */
+	uint pci1_clk_sel = gur->porpllsr & 0x8000;	/* PORPLLSR[16] */
+	uint pci2_clk_sel = gur->porpllsr & 0x4000;	/* PORPLLSR[17] */
+
+	uint pci1_speed = get_clock_freq ();	/* PCI PSPEED in [4:5] */
+
+	uint cpu_board_rev = get_cpu_board_revision ();
+
+	printf ("Board: CDS Version 0x%02x, PCI Slot %d\n",
+		get_board_version (), pci_slot);
+
+	printf ("CPU Board Revision %d.%d (0x%04x)\n",
+		MPC85XX_CPU_BOARD_MAJOR (cpu_board_rev),
+		MPC85XX_CPU_BOARD_MINOR (cpu_board_rev), cpu_board_rev);
+
+	printf ("    PCI1: %d bit, %s MHz, %s\n",
+		(pci1_32) ? 32 : 64,
+		(pci1_speed == 33000000) ? "33" :
+		(pci1_speed == 66000000) ? "66" : "unknown",
+		pci1_clk_sel ? "sync" : "async");
+
+	if (pci_dual) {
+		printf ("    PCI2: 32 bit, 66 MHz, %s\n",
+			pci2_clk_sel ? "sync" : "async");
+	} else {
+		printf ("    PCI2: disabled\n");
+	}
+
+	/*
+	 * Initialize local bus.
+	 */
+	local_bus_init ();
+
+	return 0;
+}
+
+long int
+initdram(int board_type)
+{
+	long dram_size = 0;
+	volatile immap_t *immap = (immap_t *)CFG_IMMR;
+
+	puts("Initializing\n");
+
+#if defined(CONFIG_DDR_DLL)
+	{
+		/*
+		 * Work around to stabilize DDR DLL MSYNC_IN.
+		 * Errata DDR9 seems to have been fixed.
+		 * This is now the workaround for Errata DDR11:
+		 *    Override DLL = 1, Course Adj = 1, Tap Select = 0
+		 */
+
+		volatile ccsr_gur_t *gur= &immap->im_gur;
+
+		gur->ddrdllcr = 0x81000000;
+		asm("sync;isync;msync");
+		udelay(200);
+	}
+#endif
+	dram_size = spd_sdram();
+
+#if defined(CONFIG_DDR_ECC)
+	/*
+	 * Initialize and enable DDR ECC.
+	 */
+	ddr_enable_ecc(dram_size);
+#endif
+	/*
+	 * SDRAM Initialization
+	 */
+	sdram_init();
+
+	puts("    DDR: ");
+	return dram_size;
+}
+
+/*
+ * Initialize Local Bus
+ */
+void
+local_bus_init(void)
+{
+	volatile immap_t *immap = (immap_t *)CFG_IMMR;
+	volatile ccsr_gur_t *gur = &immap->im_gur;
+	volatile ccsr_lbc_t *lbc = &immap->im_lbc;
+
+	uint clkdiv;
+	uint lbc_hz;
+	sys_info_t sysinfo;
+	uint temp_lbcdll;
+
+	/*
+	 * Errata LBC11.
+	 * Fix Local Bus clock glitch when DLL is enabled.
+	 *
+	 * If localbus freq is < 66Mhz, DLL bypass mode must be used.
+	 * If localbus freq is > 133Mhz, DLL can be safely enabled.
+	 * Between 66 and 133, the DLL is enabled with an override workaround.
+	 */
+
+	get_sys_info(&sysinfo);
+	clkdiv = lbc->lcrr & 0x0f;
+	lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv;
+
+	if (lbc_hz < 66) {
+		lbc->lcrr |= 0x80000000;	/* DLL Bypass */
+
+	} else if (lbc_hz >= 133) {
+		lbc->lcrr &= (~0x80000000);		/* DLL Enabled */
+
+	} else {
+		lbc->lcrr &= (~0x8000000);	/* DLL Enabled */
+		udelay(200);
+
+		/*
+		 * Sample LBC DLL ctrl reg, upshift it to set the
+		 * override bits.
+		 */
+		temp_lbcdll = gur->lbcdllcr;
+		gur->lbcdllcr = (((temp_lbcdll & 0xff) << 16) | 0x80000000);
+		asm("sync;isync;msync");
+	}
+}
+
+/*
+ * Initialize SDRAM memory on the Local Bus.
+ */
+void
+sdram_init(void)
+{
+#if defined(CFG_OR2_PRELIM) && defined(CFG_BR2_PRELIM)
+
+	uint idx;
+	volatile immap_t *immap = (immap_t *)CFG_IMMR;
+	volatile ccsr_lbc_t *lbc = &immap->im_lbc;
+	uint *sdram_addr = (uint *)CFG_LBC_SDRAM_BASE;
+	uint cpu_board_rev;
+	uint lsdmr_common;
+
+	puts("    SDRAM: ");
+
+	print_size (CFG_LBC_SDRAM_SIZE * 1024 * 1024, "\n");
+
+	/*
+	 * Setup SDRAM Base and Option Registers
+	 */
+	lbc->or2 = CFG_OR2_PRELIM;
+	asm("msync");
+
+	lbc->br2 = CFG_BR2_PRELIM;
+	asm("msync");
+
+	lbc->lbcr = CFG_LBC_LBCR;
+	asm("msync");
+
+	lbc->lsrt = CFG_LBC_LSRT;
+	lbc->mrtpr = CFG_LBC_MRTPR;
+	asm("msync");
+
+	/*
+	 * Determine which address lines to use baed on CPU board rev.
+	 */
+	cpu_board_rev = get_cpu_board_revision();
+	lsdmr_common = CFG_LBC_LSDMR_COMMON;
+	if (cpu_board_rev == MPC85XX_CPU_BOARD_REV_1_0) {
+		lsdmr_common |= CFG_LBC_LSDMR_BSMA1617;
+	} else if (cpu_board_rev == MPC85XX_CPU_BOARD_REV_1_1) {
+		lsdmr_common |= CFG_LBC_LSDMR_BSMA1516;
+	} else {
+		/*
+		 * Assume something unable to identify itself is
+		 * really old, and likely has lines 16/17 mapped.
+		 */
+		lsdmr_common |= CFG_LBC_LSDMR_BSMA1617;
+	}
+
+	/*
+	 * Issue PRECHARGE ALL command.
+	 */
+	lbc->lsdmr = lsdmr_common | CFG_LBC_LSDMR_OP_PCHALL;
+	asm("sync;msync");
+	*sdram_addr = 0xff;
+	ppcDcbf((unsigned long) sdram_addr);
+	udelay(100);
+
+	/*
+	 * Issue 8 AUTO REFRESH commands.
+	 */
+	for (idx = 0; idx < 8; idx++) {
+		lbc->lsdmr = lsdmr_common | CFG_LBC_LSDMR_OP_ARFRSH;
+		asm("sync;msync");
+		*sdram_addr = 0xff;
+		ppcDcbf((unsigned long) sdram_addr);
+		udelay(100);
+	}
+
+	/*
+	 * Issue 8 MODE-set command.
+	 */
+	lbc->lsdmr = lsdmr_common | CFG_LBC_LSDMR_OP_MRW;
+	asm("sync;msync");
+	*sdram_addr = 0xff;
+	ppcDcbf((unsigned long) sdram_addr);
+	udelay(100);
+
+	/*
+	 * Issue NORMAL OP command.
+	 */
+	lbc->lsdmr = lsdmr_common | CFG_LBC_LSDMR_OP_NORMAL;
+	asm("sync;msync");
+	*sdram_addr = 0xff;
+	ppcDcbf((unsigned long) sdram_addr);
+	udelay(200);    /* Overkill. Must wait > 200 bus cycles */
+
+#endif	/* enable SDRAM init */
+}
+
+#if defined(CFG_DRAM_TEST)
+int
+testdram(void)
+{
+	uint *pstart = (uint *) CFG_MEMTEST_START;
+	uint *pend = (uint *) CFG_MEMTEST_END;
+	uint *p;
+
+	printf("Testing DRAM from 0x%08x to 0x%08x\n",
+	       CFG_MEMTEST_START,
+	       CFG_MEMTEST_END);
+
+	printf("DRAM test phase 1:\n");
+	for (p = pstart; p < pend; p++)
+		*p = 0xaaaaaaaa;
+
+	for (p = pstart; p < pend; p++) {
+		if (*p != 0xaaaaaaaa) {
+			printf ("DRAM test fails at: %08x\n", (uint) p);
+			return 1;
+		}
+	}
+
+	printf("DRAM test phase 2:\n");
+	for (p = pstart; p < pend; p++)
+		*p = 0x55555555;
+
+	for (p = pstart; p < pend; p++) {
+		if (*p != 0x55555555) {
+			printf ("DRAM test fails at: %08x\n", (uint) p);
+			return 1;
+		}
+	}
+
+	printf("DRAM test passed.\n");
+	return 0;
+}
+#endif
+
+#if defined(CONFIG_PCI)
+
+/*
+ * Initialize PCI Devices, report devices found.
+ */
+
+#ifndef CONFIG_PCI_PNP
+static struct pci_config_table pci_mpc85xxcds_config_table[] = {
+    { PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
+      PCI_IDSEL_NUMBER, PCI_ANY_ID,
+      pci_cfgfunc_config_device, { PCI_ENET0_IOADDR,
+				   PCI_ENET0_MEMADDR,
+				   PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER
+      } },
+    { }
+};
+#endif
+
+static struct pci_controller hose = {
+#ifndef CONFIG_PCI_PNP
+	config_table: pci_mpc85xxcds_config_table,
+#endif
+};
+
+#endif	/* CONFIG_PCI */
+
+void
+pci_init_board(void)
+{
+#ifdef CONFIG_PCI
+	extern void pci_mpc85xx_init(struct pci_controller *hose);
+
+	pci_mpc85xx_init(&hose);
+#endif
+}

board/cds/mpc8555cds/u-boot.lds

@@ -0,0 +1,147 @@
+/*
+ * Copyright 2004 Freescale Semiconductor.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+/* Do we need any of these for elf?
+   __DYNAMIC = 0;    */
+SECTIONS
+{
+  .resetvec 0xFFFFFFFC :
+  {
+    *(.resetvec)
+  } = 0xffff
+
+  .bootpg 0xFFFFF000 :
+  {
+    cpu/mpc85xx/start.o	(.bootpg)
+    board/cds/mpc8555cds/init.o (.bootpg)
+  } = 0xffff
+
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)		}
+  .rela.text     : { *(.rela.text) 	}
+  .rel.data      : { *(.rel.data)		}
+  .rela.data     : { *(.rela.data) 	}
+  .rel.rodata    : { *(.rel.rodata) 	}
+  .rela.rodata   : { *(.rela.rodata) 	}
+  .rel.got       : { *(.rel.got)		}
+  .rela.got      : { *(.rela.got)		}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)		}
+  .rela.bss      : { *(.rela.bss)		}
+  .rel.plt       : { *(.rel.plt)		}
+  .rela.plt      : { *(.rela.plt)		}
+  .init          : { *(.init)	}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    cpu/mpc85xx/start.o	(.text)
+    board/cds/mpc8555cds/init.o (.text)
+    cpu/mpc85xx/traps.o (.text)
+    cpu/mpc85xx/interrupts.o (.text)
+    cpu/mpc85xx/cpu_init.o (.text)
+    cpu/mpc85xx/cpu.o (.text)
+    cpu/mpc85xx/tsec.o (.text)
+    cpu/mpc85xx/speed.o (.text)
+    cpu/mpc85xx/pci.o (.text)
+    common/dlmalloc.o (.text)
+    lib_generic/crc32.o (.text)
+    lib_ppc/extable.o (.text)
+    lib_generic/zlib.o (.text)
+    *(.text)
+    *(.fixup)
+    *(.got1)
+   }
+    _etext = .;
+    PROVIDE (etext = .);
+    .rodata    :
+   {
+    *(.rodata)
+    *(.rodata1)
+    *(.rodata.str1.4)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x00FF) & 0xFFFFFF00;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2;
+  __fixup_entries = (. - _FIXUP_TABLE_) >> 2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  __u_boot_cmd_start = .;
+  .u_boot_cmd : { *(.u_boot_cmd) }
+  __u_boot_cmd_end = .;
+
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(256);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(256);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+  _end = . ;
+  PROVIDE (end = .);
+}

board/cerf250/cerf250.c

@@ -42,7 +42,7 @@ int board_init (void)
 	/* so we do _nothing_ here */
 
 	/* arch number of cerf PXA Board */
-	gd->bd->bi_arch_number = 139;
+	gd->bd->bi_arch_number = MACH_TYPE_PXA_CERF;
 
 	/* adress of boot parameters */
 	gd->bd->bi_boot_params = 0xa0000100;

board/cmc_pu2/Makefile

@@ -0,0 +1,47 @@
+#
+# (C) Copyright 2003
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	:= at91rm9200dk.o at45.o dm9161.o flash.o
+SOBJS	:= memsetup.o
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) crv $@ $(OBJS) $(SOBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+-include .depend
+
+#########################################################################

board/cmc_pu2/at45.c

@@ -0,0 +1,621 @@
+/* Driver for ATMEL DataFlash support
+ * Author : Hamid Ikdoumi (Atmel)
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+#include <config.h>
+#include <common.h>
+#include <asm/hardware.h>
+
+#ifdef CONFIG_HAS_DATAFLASH
+#include <dataflash.h>
+
+#define AT91C_SPI_CLK	10000000	/* Max Value = 10MHz to be compliant to
+the Continuous Array Read function */
+
+/* AC Characteristics */
+/* DLYBS = tCSS = 250ns min and DLYBCT = tCSH = 250ns */
+#define DATAFLASH_TCSS	(0xC << 16)
+#define DATAFLASH_TCHS	(0x1 << 24)
+
+#define AT91C_TIMEOUT_WRDY			200000
+#define AT91C_SPI_PCS0_SERIAL_DATAFLASH		0xE     /* Chip Select 0 : NPCS0 %1110 */
+#define AT91C_SPI_PCS3_DATAFLASH_CARD		0x7     /* Chip Select 3 : NPCS3 %0111 */
+
+void AT91F_SpiInit(void) {
+
+/*-------------------------------------------------------------------*/
+/*	SPI DataFlash Init								*/
+/*-------------------------------------------------------------------*/
+	/* Configure PIOs */
+	AT91C_BASE_PIOA->PIO_ASR = AT91C_PA3_NPCS0 | AT91C_PA4_NPCS1 | AT91C_PA1_MOSI | AT91C_PA5_NPCS2 |
+				   AT91C_PA6_NPCS3 | AT91C_PA0_MISO | AT91C_PA2_SPCK;
+	AT91C_BASE_PIOA->PIO_PDR = AT91C_PA3_NPCS0 | AT91C_PA4_NPCS1 | AT91C_PA1_MOSI | AT91C_PA5_NPCS2 |
+				   AT91C_PA6_NPCS3 | AT91C_PA0_MISO | AT91C_PA2_SPCK;
+	/* Enable CLock */
+	AT91C_BASE_PMC->PMC_PCER = 1 << AT91C_ID_SPI;
+
+	/* Reset the SPI */
+	AT91C_BASE_SPI->SPI_CR = AT91C_SPI_SWRST;
+
+	/* Configure SPI in Master Mode with No CS selected !!! */
+	AT91C_BASE_SPI->SPI_MR = AT91C_SPI_MSTR | AT91C_SPI_MODFDIS | AT91C_SPI_PCS;
+
+	/* Configure CS0 and CS3 */
+	*(AT91C_SPI_CSR + 0) = AT91C_SPI_CPOL | (AT91C_SPI_DLYBS & DATAFLASH_TCSS) | (AT91C_SPI_DLYBCT &
+	DATAFLASH_TCHS) | ((AT91C_MASTER_CLOCK / (2*AT91C_SPI_CLK)) << 8);
+
+	*(AT91C_SPI_CSR + 3) = AT91C_SPI_CPOL | (AT91C_SPI_DLYBS & DATAFLASH_TCSS) | (AT91C_SPI_DLYBCT &
+	DATAFLASH_TCHS) | ((AT91C_MASTER_CLOCK / (2*AT91C_SPI_CLK)) << 8);
+
+}
+
+void AT91F_SpiEnable(int cs) {
+	switch(cs) {
+	case 0:	/* Configure SPI CS0 for Serial DataFlash AT45DBxx */
+		AT91C_BASE_SPI->SPI_MR &= 0xFFF0FFFF;
+		AT91C_BASE_SPI->SPI_MR |= ((AT91C_SPI_PCS0_SERIAL_DATAFLASH<<16) & AT91C_SPI_PCS);
+		break;
+	case 3:	/* Configure SPI CS3 for Serial DataFlash Card */
+		/* Set up PIO SDC_TYPE to switch on DataFlash Card and not MMC/SDCard */
+		AT91C_BASE_PIOB->PIO_PER = AT91C_PIO_PB7;	/* Set in PIO mode */
+		AT91C_BASE_PIOB->PIO_OER = AT91C_PIO_PB7;	/* Configure in output */
+		/* Clear Output */
+		AT91C_BASE_PIOB->PIO_CODR = AT91C_PIO_PB7;
+		/* Configure PCS */
+		AT91C_BASE_SPI->SPI_MR &= 0xFFF0FFFF;
+		AT91C_BASE_SPI->SPI_MR |= ((AT91C_SPI_PCS3_DATAFLASH_CARD<<16) & AT91C_SPI_PCS);
+		break;
+	}
+
+	/* SPI_Enable */
+	AT91C_BASE_SPI->SPI_CR = AT91C_SPI_SPIEN;
+}
+
+/*----------------------------------------------------------------------------*/
+/* \fn    AT91F_SpiWrite						      */
+/* \brief Set the PDC registers for a transfert				      */
+/*----------------------------------------------------------------------------*/
+unsigned int AT91F_SpiWrite ( AT91PS_DataflashDesc pDesc )
+{
+	unsigned int timeout;
+
+	pDesc->state = BUSY;
+
+	AT91C_BASE_SPI->SPI_PTCR = AT91C_PDC_TXTDIS + AT91C_PDC_RXTDIS;
+
+	/* Initialize the Transmit and Receive Pointer */
+	AT91C_BASE_SPI->SPI_RPR = (unsigned int)pDesc->rx_cmd_pt ;
+	AT91C_BASE_SPI->SPI_TPR = (unsigned int)pDesc->tx_cmd_pt ;
+
+	/* Intialize the Transmit and Receive Counters */
+	AT91C_BASE_SPI->SPI_RCR = pDesc->rx_cmd_size;
+	AT91C_BASE_SPI->SPI_TCR = pDesc->tx_cmd_size;
+
+	if ( pDesc->tx_data_size != 0 ) {
+		/* Initialize the Next Transmit and Next Receive Pointer */
+		AT91C_BASE_SPI->SPI_RNPR = (unsigned int)pDesc->rx_data_pt ;
+		AT91C_BASE_SPI->SPI_TNPR = (unsigned int)pDesc->tx_data_pt ;
+
+		/* Intialize the Next Transmit and Next Receive Counters */
+		AT91C_BASE_SPI->SPI_RNCR = pDesc->rx_data_size ;
+		AT91C_BASE_SPI->SPI_TNCR = pDesc->tx_data_size ;
+	}
+
+	/* arm simple, non interrupt dependent timer */
+	reset_timer_masked();
+	timeout = 0;
+
+	AT91C_BASE_SPI->SPI_PTCR = AT91C_PDC_TXTEN + AT91C_PDC_RXTEN;
+	while(!(AT91C_BASE_SPI->SPI_SR & AT91C_SPI_RXBUFF) && ((timeout = get_timer_masked() ) < CFG_SPI_WRITE_TOUT));
+	AT91C_BASE_SPI->SPI_PTCR = AT91C_PDC_TXTDIS + AT91C_PDC_RXTDIS;
+	pDesc->state = IDLE;
+
+	if (timeout >= CFG_SPI_WRITE_TOUT){
+		printf("Error Timeout\n\r");
+		return DATAFLASH_ERROR;
+	}
+
+	return DATAFLASH_OK;
+}
+
+
+/*----------------------------------------------------------------------*/
+/* \fn    AT91F_DataFlashSendCommand					*/
+/* \brief Generic function to send a command to the dataflash		*/
+/*----------------------------------------------------------------------*/
+AT91S_DataFlashStatus AT91F_DataFlashSendCommand(
+	AT91PS_DataFlash pDataFlash,
+	unsigned char OpCode,
+	unsigned int CmdSize,
+	unsigned int DataflashAddress)
+{
+    unsigned int adr;
+
+	if ( (pDataFlash->pDataFlashDesc->state) != IDLE)
+		return DATAFLASH_BUSY;
+
+	/* process the address to obtain page address and byte address */
+	adr = ((DataflashAddress / (pDataFlash->pDevice->pages_size)) << pDataFlash->pDevice->page_offset) + (DataflashAddress % (pDataFlash->pDevice->pages_size));
+
+	/* fill the  command  buffer */
+	pDataFlash->pDataFlashDesc->command[0] = OpCode;
+	if (pDataFlash->pDevice->pages_number >= 16384) {
+		pDataFlash->pDataFlashDesc->command[1] = (unsigned char)((adr & 0x0F000000) >> 24);
+		pDataFlash->pDataFlashDesc->command[2] = (unsigned char)((adr & 0x00FF0000) >> 16);
+		pDataFlash->pDataFlashDesc->command[3] = (unsigned char)((adr & 0x0000FF00) >> 8);
+		pDataFlash->pDataFlashDesc->command[4] = (unsigned char)(adr & 0x000000FF);
+	} else {
+		pDataFlash->pDataFlashDesc->command[1] = (unsigned char)((adr & 0x00FF0000) >> 16);
+		pDataFlash->pDataFlashDesc->command[2] = (unsigned char)((adr & 0x0000FF00) >> 8);
+		pDataFlash->pDataFlashDesc->command[3] = (unsigned char)(adr & 0x000000FF) ;
+		pDataFlash->pDataFlashDesc->command[4] = 0;
+	}
+	pDataFlash->pDataFlashDesc->command[5] = 0;
+	pDataFlash->pDataFlashDesc->command[6] = 0;
+	pDataFlash->pDataFlashDesc->command[7] = 0;
+
+	/* Initialize the SpiData structure for the spi write fuction */
+	pDataFlash->pDataFlashDesc->tx_cmd_pt   =  pDataFlash->pDataFlashDesc->command ;
+	pDataFlash->pDataFlashDesc->tx_cmd_size =  CmdSize ;
+	pDataFlash->pDataFlashDesc->rx_cmd_pt   =  pDataFlash->pDataFlashDesc->command ;
+	pDataFlash->pDataFlashDesc->rx_cmd_size =  CmdSize ;
+
+	/* send the command and read the data */
+	return AT91F_SpiWrite (pDataFlash->pDataFlashDesc);
+}
+
+
+/*----------------------------------------------------------------------*/
+/* \fn    AT91F_DataFlashGetStatus					*/
+/* \brief Read the status register of the dataflash			*/
+/*----------------------------------------------------------------------*/
+AT91S_DataFlashStatus AT91F_DataFlashGetStatus(AT91PS_DataflashDesc pDesc)
+{
+	AT91S_DataFlashStatus status;
+
+	/* if a transfert is in progress ==> return 0 */
+	if( (pDesc->state) != IDLE)
+		return DATAFLASH_BUSY;
+
+	/* first send the read status command (D7H) */
+	pDesc->command[0] = DB_STATUS;
+	pDesc->command[1] = 0;
+
+	pDesc->DataFlash_state  = GET_STATUS;
+	pDesc->tx_data_size 	= 0 ;	/* Transmit the command and receive response */
+	pDesc->tx_cmd_pt 		= pDesc->command ;
+	pDesc->rx_cmd_pt 		= pDesc->command ;
+	pDesc->rx_cmd_size 		= 2 ;
+	pDesc->tx_cmd_size 		= 2 ;
+	status = AT91F_SpiWrite (pDesc);
+
+	pDesc->DataFlash_state = *( (unsigned char *) (pDesc->rx_cmd_pt) +1);
+
+	return status;
+}
+
+
+/*----------------------------------------------------------------------*/
+/* \fn    AT91F_DataFlashWaitReady					*/
+/* \brief wait for dataflash ready (bit7 of the status register == 1)	*/
+/*----------------------------------------------------------------------*/
+AT91S_DataFlashStatus AT91F_DataFlashWaitReady(AT91PS_DataflashDesc pDataFlashDesc, unsigned int timeout)
+{
+	pDataFlashDesc->DataFlash_state = IDLE;
+
+	do {
+		AT91F_DataFlashGetStatus(pDataFlashDesc);
+		timeout--;
+	} while( ((pDataFlashDesc->DataFlash_state & 0x80) != 0x80) && (timeout > 0) );
+
+	if((pDataFlashDesc->DataFlash_state & 0x80) != 0x80)
+		return DATAFLASH_ERROR;
+
+	return DATAFLASH_OK;
+}
+
+
+/*------------------------------------------------------------------------------*/
+/* Function Name       : AT91F_DataFlashContinuousRead 				*/
+/* Object              : Continuous stream Read 				*/
+/* Input Parameters    : DataFlash Service					*/
+/*						: <src> = dataflash address	*/
+/*                     : <*dataBuffer> = data buffer pointer			*/
+/*                     : <sizeToRead> = data buffer size			*/
+/* Return value		: State of the dataflash				*/
+/*------------------------------------------------------------------------------*/
+AT91S_DataFlashStatus AT91F_DataFlashContinuousRead (
+	AT91PS_DataFlash pDataFlash,
+	int src,
+	unsigned char *dataBuffer,
+	int sizeToRead )
+{
+	AT91S_DataFlashStatus status;
+	/* Test the size to read in the device */
+	if ( (src + sizeToRead) > (pDataFlash->pDevice->pages_size * (pDataFlash->pDevice->pages_number)))
+		return DATAFLASH_MEMORY_OVERFLOW;
+
+	pDataFlash->pDataFlashDesc->rx_data_pt = dataBuffer;
+	pDataFlash->pDataFlashDesc->rx_data_size = sizeToRead;
+	pDataFlash->pDataFlashDesc->tx_data_pt = dataBuffer;
+	pDataFlash->pDataFlashDesc->tx_data_size = sizeToRead;
+
+	status = AT91F_DataFlashSendCommand (pDataFlash, DB_CONTINUOUS_ARRAY_READ, 8, src);
+	/* Send the command to the dataflash */
+	return(status);
+}
+
+
+/*------------------------------------------------------------------------------*/
+/* Function Name       : AT91F_DataFlashPagePgmBuf				*/
+/* Object              : Main memory page program through buffer 1 or buffer 2	*/
+/* Input Parameters    : DataFlash Service					*/
+/*						: <*src> = Source buffer	*/
+/*                     : <dest> = dataflash destination address			*/
+/*                     : <SizeToWrite> = data buffer size			*/
+/* Return value		: State of the dataflash				*/
+/*------------------------------------------------------------------------------*/
+AT91S_DataFlashStatus AT91F_DataFlashPagePgmBuf(
+	AT91PS_DataFlash pDataFlash,
+	unsigned char *src,
+	unsigned int dest,
+	unsigned int SizeToWrite)
+{
+	int cmdsize;
+	pDataFlash->pDataFlashDesc->tx_data_pt = src ;
+	pDataFlash->pDataFlashDesc->tx_data_size = SizeToWrite ;
+	pDataFlash->pDataFlashDesc->rx_data_pt = src;
+	pDataFlash->pDataFlashDesc->rx_data_size = SizeToWrite;
+
+	cmdsize = 4;
+	/* Send the command to the dataflash */
+	if (pDataFlash->pDevice->pages_number >= 16384)
+		cmdsize = 5;
+	return(AT91F_DataFlashSendCommand (pDataFlash, DB_PAGE_PGM_BUF1, cmdsize, dest));
+}
+
+
+/*------------------------------------------------------------------------------*/
+/* Function Name       : AT91F_MainMemoryToBufferTransfert			*/
+/* Object              : Read a page in the SRAM Buffer 1 or 2			*/
+/* Input Parameters    : DataFlash Service					*/
+/*                     : Page concerned						*/
+/*                     : 							*/
+/* Return value		: State of the dataflash				*/
+/*------------------------------------------------------------------------------*/
+AT91S_DataFlashStatus AT91F_MainMemoryToBufferTransfert(
+	AT91PS_DataFlash pDataFlash,
+	unsigned char BufferCommand,
+	unsigned int page)
+{
+	int cmdsize;
+	/* Test if the buffer command is legal */
+	if ((BufferCommand != DB_PAGE_2_BUF1_TRF) && (BufferCommand != DB_PAGE_2_BUF2_TRF))
+		return DATAFLASH_BAD_COMMAND;
+
+	/* no data to transmit or receive */
+	pDataFlash->pDataFlashDesc->tx_data_size = 0;
+	cmdsize = 4;
+	if (pDataFlash->pDevice->pages_number >= 16384)
+		cmdsize = 5;
+	return(AT91F_DataFlashSendCommand (pDataFlash, BufferCommand, cmdsize, page*pDataFlash->pDevice->pages_size));
+}
+
+
+/*----------------------------------------------------------------------------- */
+/* Function Name       : AT91F_DataFlashWriteBuffer				*/
+/* Object              : Write data to the internal sram buffer 1 or 2		*/
+/* Input Parameters    : DataFlash Service					*/
+/*			: <BufferCommand> = command to write buffer1 or buffer2	*/
+/*                     : <*dataBuffer> = data buffer to write			*/
+/*                     : <bufferAddress> = address in the internal buffer	*/
+/*                     : <SizeToWrite> = data buffer size			*/
+/* Return value		: State of the dataflash				*/
+/*------------------------------------------------------------------------------*/
+AT91S_DataFlashStatus AT91F_DataFlashWriteBuffer (
+	AT91PS_DataFlash pDataFlash,
+	unsigned char BufferCommand,
+	unsigned char *dataBuffer,
+	unsigned int bufferAddress,
+	int SizeToWrite )
+{
+	int cmdsize;
+	/* Test if the buffer command is legal */
+	if ((BufferCommand != DB_BUF1_WRITE) && (BufferCommand != DB_BUF2_WRITE))
+		return DATAFLASH_BAD_COMMAND;
+
+	/* buffer address must be lower than page size */
+	if (bufferAddress > pDataFlash->pDevice->pages_size)
+		return DATAFLASH_BAD_ADDRESS;
+
+	if ( (pDataFlash->pDataFlashDesc->state)  != IDLE)
+		return DATAFLASH_BUSY;
+
+	/* Send first Write Command */
+	pDataFlash->pDataFlashDesc->command[0] = BufferCommand;
+	pDataFlash->pDataFlashDesc->command[1] = 0;
+	if (pDataFlash->pDevice->pages_number >= 16384) {
+	    	pDataFlash->pDataFlashDesc->command[2] = 0;
+	    	pDataFlash->pDataFlashDesc->command[3] = (unsigned char)(((unsigned int)(bufferAddress &  pDataFlash->pDevice->byte_mask)) >> 8) ;
+	    	pDataFlash->pDataFlashDesc->command[4] = (unsigned char)((unsigned int)bufferAddress  & 0x00FF) ;
+		cmdsize = 5;
+	} else {
+	    	pDataFlash->pDataFlashDesc->command[2] = (unsigned char)(((unsigned int)(bufferAddress &  pDataFlash->pDevice->byte_mask)) >> 8) ;
+	    	pDataFlash->pDataFlashDesc->command[3] = (unsigned char)((unsigned int)bufferAddress  & 0x00FF) ;
+	    	pDataFlash->pDataFlashDesc->command[4] = 0;
+		cmdsize = 4;
+	}
+
+	pDataFlash->pDataFlashDesc->tx_cmd_pt 	 = pDataFlash->pDataFlashDesc->command ;
+	pDataFlash->pDataFlashDesc->tx_cmd_size = cmdsize ;
+	pDataFlash->pDataFlashDesc->rx_cmd_pt 	 = pDataFlash->pDataFlashDesc->command ;
+	pDataFlash->pDataFlashDesc->rx_cmd_size = cmdsize ;
+
+	pDataFlash->pDataFlashDesc->rx_data_pt 	= dataBuffer ;
+	pDataFlash->pDataFlashDesc->tx_data_pt 	= dataBuffer ;
+	pDataFlash->pDataFlashDesc->rx_data_size 	= SizeToWrite ;
+	pDataFlash->pDataFlashDesc->tx_data_size 	= SizeToWrite ;
+
+	return AT91F_SpiWrite(pDataFlash->pDataFlashDesc);
+}
+
+/*------------------------------------------------------------------------------*/
+/* Function Name       : AT91F_PageErase                                        */
+/* Object              : Erase a page 						*/
+/* Input Parameters    : DataFlash Service					*/
+/*                     : Page concerned						*/
+/*                     : 							*/
+/* Return value		: State of the dataflash				*/
+/*------------------------------------------------------------------------------*/
+AT91S_DataFlashStatus AT91F_PageErase(
+	AT91PS_DataFlash pDataFlash,
+	unsigned int page)
+{
+	int cmdsize;
+	/* Test if the buffer command is legal */
+	/* no data to transmit or receive */
+    	pDataFlash->pDataFlashDesc->tx_data_size = 0;
+
+	cmdsize = 4;
+	if (pDataFlash->pDevice->pages_number >= 16384)
+		cmdsize = 5;
+	return(AT91F_DataFlashSendCommand (pDataFlash, DB_PAGE_ERASE, cmdsize, page*pDataFlash->pDevice->pages_size));
+}
+
+
+/*------------------------------------------------------------------------------*/
+/* Function Name       : AT91F_BlockErase                                       */
+/* Object              : Erase a Block 						*/
+/* Input Parameters    : DataFlash Service					*/
+/*                     : Page concerned						*/
+/*                     : 							*/
+/* Return value		: State of the dataflash				*/
+/*------------------------------------------------------------------------------*/
+AT91S_DataFlashStatus AT91F_BlockErase(
+	AT91PS_DataFlash pDataFlash,
+	unsigned int block)
+{
+	int cmdsize;
+	/* Test if the buffer command is legal */
+	/* no data to transmit or receive */
+    	pDataFlash->pDataFlashDesc->tx_data_size = 0;
+	cmdsize = 4;
+	if (pDataFlash->pDevice->pages_number >= 16384)
+		cmdsize = 5;
+	return(AT91F_DataFlashSendCommand (pDataFlash, DB_BLOCK_ERASE,cmdsize, block*8*pDataFlash->pDevice->pages_size));
+}
+
+/*------------------------------------------------------------------------------*/
+/* Function Name       : AT91F_WriteBufferToMain				*/
+/* Object              : Write buffer to the main memory			*/
+/* Input Parameters    : DataFlash Service					*/
+/*		: <BufferCommand> = command to send to buffer1 or buffer2	*/
+/*                     : <dest> = main memory address				*/
+/* Return value		: State of the dataflash				*/
+/*------------------------------------------------------------------------------*/
+AT91S_DataFlashStatus AT91F_WriteBufferToMain (
+	AT91PS_DataFlash pDataFlash,
+	unsigned char BufferCommand,
+	unsigned int dest )
+{
+	int cmdsize;
+	/* Test if the buffer command is correct */
+	if ((BufferCommand != DB_BUF1_PAGE_PGM) &&
+	    (BufferCommand != DB_BUF1_PAGE_ERASE_PGM) &&
+	    (BufferCommand != DB_BUF2_PAGE_PGM) &&
+	    (BufferCommand != DB_BUF2_PAGE_ERASE_PGM) )
+		return DATAFLASH_BAD_COMMAND;
+
+	/* no data to transmit or receive */
+	pDataFlash->pDataFlashDesc->tx_data_size = 0;
+
+	cmdsize = 4;
+	if (pDataFlash->pDevice->pages_number >= 16384)
+		cmdsize = 5;
+	/* Send the command to the dataflash */
+	return(AT91F_DataFlashSendCommand (pDataFlash, BufferCommand, cmdsize, dest));
+}
+
+
+/*------------------------------------------------------------------------------*/
+/* Function Name       : AT91F_PartialPageWrite					*/
+/* Object              : Erase partielly a page					*/
+/* Input Parameters    : <page> = page number					*/
+/*			: <AdrInpage> = adr to begin the fading			*/
+/*                     : <length> = Number of bytes to erase			*/
+/*------------------------------------------------------------------------------*/
+AT91S_DataFlashStatus AT91F_PartialPageWrite (
+	AT91PS_DataFlash pDataFlash,
+	unsigned char *src,
+	unsigned int dest,
+	unsigned int size)
+{
+	unsigned int page;
+	unsigned int AdrInPage;
+
+	page = dest / (pDataFlash->pDevice->pages_size);
+	AdrInPage = dest % (pDataFlash->pDevice->pages_size);
+
+	/* Read the contents of the page in the Sram Buffer */
+	AT91F_MainMemoryToBufferTransfert(pDataFlash, DB_PAGE_2_BUF1_TRF, page);
+	AT91F_DataFlashWaitReady(pDataFlash->pDataFlashDesc, AT91C_TIMEOUT_WRDY);
+	/*Update the SRAM buffer */
+	AT91F_DataFlashWriteBuffer(pDataFlash, DB_BUF1_WRITE, src, AdrInPage, size);
+
+	AT91F_DataFlashWaitReady(pDataFlash->pDataFlashDesc, AT91C_TIMEOUT_WRDY);
+
+	/* Erase page if a 128 Mbits device */
+	if (pDataFlash->pDevice->pages_number >= 16384) {
+		AT91F_PageErase(pDataFlash, page);
+		/* Rewrite the modified Sram Buffer in the main memory */
+		AT91F_DataFlashWaitReady(pDataFlash->pDataFlashDesc, AT91C_TIMEOUT_WRDY);
+	}
+
+	/* Rewrite the modified Sram Buffer in the main memory */
+	return(AT91F_WriteBufferToMain(pDataFlash, DB_BUF1_PAGE_ERASE_PGM, (page*pDataFlash->pDevice->pages_size)));
+}
+
+
+/*------------------------------------------------------------------------------*/
+/* Function Name       : AT91F_DataFlashWrite					*/
+/* Object              :							*/
+/* Input Parameters    : <*src> = Source buffer					*/
+/*                     : <dest> = dataflash adress				*/
+/*                     : <size> = data buffer size				*/
+/*------------------------------------------------------------------------------*/
+AT91S_DataFlashStatus AT91F_DataFlashWrite(
+	AT91PS_DataFlash pDataFlash,
+	unsigned char *src,
+	int dest,
+	int size )
+{
+	unsigned int length;
+	unsigned int page;
+	unsigned int status;
+
+	AT91F_SpiEnable(pDataFlash->pDevice->cs);
+
+	if ( (dest + size) > (pDataFlash->pDevice->pages_size * (pDataFlash->pDevice->pages_number)))
+		return DATAFLASH_MEMORY_OVERFLOW;
+
+	/* If destination does not fit a page start address */
+	if ((dest % ((unsigned int)(pDataFlash->pDevice->pages_size)))  != 0 ) {
+		length = pDataFlash->pDevice->pages_size - (dest % ((unsigned int)(pDataFlash->pDevice->pages_size)));
+
+		if (size < length)
+			length = size;
+
+		if(!AT91F_PartialPageWrite(pDataFlash,src, dest, length))
+			return DATAFLASH_ERROR;
+
+		AT91F_DataFlashWaitReady(pDataFlash->pDataFlashDesc, AT91C_TIMEOUT_WRDY);
+
+		/* Update size, source and destination pointers */
+		size -= length;
+		dest += length;
+		src += length;
+	}
+
+	while (( size - pDataFlash->pDevice->pages_size ) >= 0 ) {
+		/* program dataflash page */
+		page = (unsigned int)dest / (pDataFlash->pDevice->pages_size);
+
+		status = AT91F_DataFlashWriteBuffer(pDataFlash, DB_BUF1_WRITE, src, 0, pDataFlash->pDevice->pages_size);
+		AT91F_DataFlashWaitReady(pDataFlash->pDataFlashDesc, AT91C_TIMEOUT_WRDY);
+
+		status = AT91F_PageErase(pDataFlash, page);
+		AT91F_DataFlashWaitReady(pDataFlash->pDataFlashDesc, AT91C_TIMEOUT_WRDY);
+		if (!status)
+			return DATAFLASH_ERROR;
+
+		status = AT91F_WriteBufferToMain (pDataFlash, DB_BUF1_PAGE_PGM, dest);
+		if(!status)
+			return DATAFLASH_ERROR;
+
+		AT91F_DataFlashWaitReady(pDataFlash->pDataFlashDesc, AT91C_TIMEOUT_WRDY);
+
+		/* Update size, source and destination pointers */
+		size -= pDataFlash->pDevice->pages_size ;
+		dest += pDataFlash->pDevice->pages_size ;
+		src  += pDataFlash->pDevice->pages_size ;
+	}
+
+	/* If still some bytes to read */
+	if ( size > 0 ) {
+		/* program dataflash page */
+		if(!AT91F_PartialPageWrite(pDataFlash, src, dest, size) )
+			return DATAFLASH_ERROR;
+
+		AT91F_DataFlashWaitReady(pDataFlash->pDataFlashDesc, AT91C_TIMEOUT_WRDY);
+	}
+	return DATAFLASH_OK;
+}
+
+
+/*------------------------------------------------------------------------------*/
+/* Function Name       : AT91F_DataFlashRead 					*/
+/* Object              : Read a block in dataflash				*/
+/* Input Parameters    : 							*/
+/* Return value		: 							*/
+/*------------------------------------------------------------------------------*/
+int AT91F_DataFlashRead(
+	AT91PS_DataFlash pDataFlash,
+	unsigned long addr,
+	unsigned long size,
+	char *buffer)
+{
+	unsigned long SizeToRead;
+
+	AT91F_SpiEnable(pDataFlash->pDevice->cs);
+
+	if(AT91F_DataFlashWaitReady(pDataFlash->pDataFlashDesc, AT91C_TIMEOUT_WRDY) != DATAFLASH_OK)
+		return -1;
+
+	while (size) {
+		SizeToRead = (size < 0x8000)? size:0x8000;
+
+		if (AT91F_DataFlashWaitReady(pDataFlash->pDataFlashDesc, AT91C_TIMEOUT_WRDY) != DATAFLASH_OK)
+			return -1;
+
+		if (AT91F_DataFlashContinuousRead (pDataFlash, addr, buffer, SizeToRead) != DATAFLASH_OK)
+			return -1;
+
+		size -= SizeToRead;
+		addr += SizeToRead;
+		buffer += SizeToRead;
+	}
+
+	return DATAFLASH_OK;
+}
+
+
+/*------------------------------------------------------------------------------*/
+/* Function Name       : AT91F_DataflashProbe 					*/
+/* Object              : 							*/
+/* Input Parameters    : 							*/
+/* Return value	       : Dataflash status register				*/
+/*------------------------------------------------------------------------------*/
+int AT91F_DataflashProbe(int cs, AT91PS_DataflashDesc pDesc)
+{
+	AT91F_SpiEnable(cs);
+	AT91F_DataFlashGetStatus(pDesc);
+	return((pDesc->command[1] == 0xFF)? 0: pDesc->command[1] & 0x3C);
+}
+
+#endif

board/cmc_pu2/at91rm9200dk.c

@@ -0,0 +1,118 @@
+/*
+ * (C) Copyright 2002
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Marius Groeger <mgroeger@sysgo.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/arch/AT91RM9200.h>
+
+/* ------------------------------------------------------------------------- */
+/*
+ * Miscelaneous platform dependent initialisations
+ */
+
+int board_init (void)
+{
+	DECLARE_GLOBAL_DATA_PTR;
+
+	/* Enable Ctrlc */
+	console_init_f ();
+
+	/* Correct IRDA resistor problem */
+	/* Set PA23_TXD in Output */
+	(AT91PS_PIO) AT91C_BASE_PIOA->PIO_OER = AT91C_PA23_TXD2;
+
+	/* memory and cpu-speed are setup before relocation */
+	/* so we do _nothing_ here */
+
+	/* arch number of AT91RM9200DK-Board */
+	gd->bd->bi_arch_number = 251;
+	/* adress of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+	return 0;
+}
+
+int dram_init (void)
+{
+	DECLARE_GLOBAL_DATA_PTR;
+
+	gd->bd->bi_dram[0].start = PHYS_SDRAM;
+	gd->bd->bi_dram[0].size = PHYS_SDRAM_SIZE;
+	return 0;
+}
+
+/*
+ * Disk On Chip (NAND) Millenium initialization.
+ * The NAND lives in the CS2* space
+ */
+#if (CONFIG_COMMANDS & CFG_CMD_NAND)
+extern ulong nand_probe (ulong physadr);
+
+#define AT91_SMARTMEDIA_BASE 0x40000000	/* physical address to access memory on NCS3 */
+void nand_init (void)
+{
+	/* Setup Smart Media, fitst enable the address range of CS3 */
+	*AT91C_EBI_CSA |= AT91C_EBI_CS3A_SMC_SmartMedia;
+	/* set the bus interface characteristics based on
+	   tDS Data Set up Time 30 - ns
+	   tDH Data Hold Time 20 - ns
+	   tALS ALE Set up Time 20 - ns
+	   16ns at 60 MHz ~= 3  */
+/*memory mapping structures */
+#define SM_ID_RWH	(5 << 28)
+#define SM_RWH		(1 << 28)
+#define SM_RWS		(0 << 24)
+#define SM_TDF		(1 << 8)
+#define SM_NWS		(3)
+	AT91C_BASE_SMC2->SMC2_CSR[3] = (SM_RWH | SM_RWS |
+		AT91C_SMC2_ACSS_STANDARD | AT91C_SMC2_DBW_8 |
+		SM_TDF | AT91C_SMC2_WSEN | SM_NWS);
+
+	/* enable the SMOE line PC0=SMCE, A21=CLE, A22=ALE */
+	*AT91C_PIOC_ASR = AT91C_PC0_BFCK | AT91C_PC1_BFRDY_SMOE |
+		AT91C_PC3_BFBAA_SMWE;
+	*AT91C_PIOC_PDR = AT91C_PC0_BFCK | AT91C_PC1_BFRDY_SMOE |
+		AT91C_PC3_BFBAA_SMWE;
+
+	/* Configure PC2 as input (signal READY of the SmartMedia) */
+	*AT91C_PIOC_PER = AT91C_PC2_BFAVD;	/* enable direct output enable */
+	*AT91C_PIOC_ODR = AT91C_PC2_BFAVD;	/* disable output */
+
+	/* Configure PB1 as input (signal Card Detect of the SmartMedia) */
+	*AT91C_PIOB_PER = AT91C_PIO_PB1;	/* enable direct output enable */
+	*AT91C_PIOB_ODR = AT91C_PIO_PB1;	/* disable output */
+
+	/* PIOB and PIOC clock enabling */
+	*AT91C_PMC_PCER = 1 << AT91C_ID_PIOB;
+	*AT91C_PMC_PCER = 1 << AT91C_ID_PIOC;
+
+	if (*AT91C_PIOB_PDSR & AT91C_PIO_PB1)
+		printf ("  No SmartMedia card inserted\n");
+#ifdef DEBUG
+	printf ("  SmartMedia card inserted\n");
+
+	printf ("Probing at 0x%.8x\n", AT91_SMARTMEDIA_BASE);
+#endif
+	printf ("%4lu MB\n", nand_probe(AT91_SMARTMEDIA_BASE) >> 20);
+}
+#endif

board/cmc_pu2/config.mk

@@ -0,0 +1 @@
+TEXT_BASE = 0x21f00000

board/cmc_pu2/dm9161.c

@@ -0,0 +1,243 @@
+/*
+ * (C) Copyright 2003
+ * Author : Hamid Ikdoumi (Atmel)
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <at91rm9200_net.h>
+#include <net.h>
+#include <dm9161.h>
+
+#ifdef CONFIG_DRIVER_ETHER
+
+#if (CONFIG_COMMANDS & CFG_CMD_NET)
+
+/*
+ * Name:
+ *	dm9161_IsPhyConnected
+ * Description:
+ *	Reads the 2 PHY ID registers
+ * Arguments:
+ *	p_mac - pointer to AT91S_EMAC struct
+ * Return value:
+ *	TRUE - if id read successfully
+ *	FALSE- if error
+ */
+static unsigned int dm9161_IsPhyConnected (AT91PS_EMAC p_mac)
+{
+	unsigned short Id1, Id2;
+
+	at91rm9200_EmacEnableMDIO (p_mac);
+	at91rm9200_EmacReadPhy (p_mac, DM9161_PHYID1, &Id1);
+	at91rm9200_EmacReadPhy (p_mac, DM9161_PHYID2, &Id2);
+	at91rm9200_EmacDisableMDIO (p_mac);
+
+	if ((Id1 == (DM9161_PHYID1_OUI >> 6)) &&
+		((Id2 >> 10) == (DM9161_PHYID1_OUI & DM9161_LSB_MASK)))
+		return TRUE;
+
+	return FALSE;
+}
+
+/*
+ * Name:
+ *	dm9161_GetLinkSpeed
+ * Description:
+ *	Link parallel detection status of MAC is checked and set in the
+ *	MAC configuration registers
+ * Arguments:
+ *	p_mac - pointer to MAC
+ * Return value:
+ *	TRUE - if link status set succesfully
+ *	FALSE - if link status not set
+ */
+static UCHAR dm9161_GetLinkSpeed (AT91PS_EMAC p_mac)
+{
+	unsigned short stat1, stat2;
+
+	if (!at91rm9200_EmacReadPhy (p_mac, DM9161_BMSR, &stat1))
+		return FALSE;
+
+	if (!(stat1 & DM9161_LINK_STATUS))	/* link status up? */
+		return FALSE;
+
+	if (!at91rm9200_EmacReadPhy (p_mac, DM9161_DSCSR, &stat2))
+		return FALSE;
+
+	if ((stat1 & DM9161_100BASE_TX_FD) && (stat2 & DM9161_100FDX)) {
+		/*set Emac for 100BaseTX and Full Duplex  */
+		p_mac->EMAC_CFG |= AT91C_EMAC_SPD | AT91C_EMAC_FD;
+		return TRUE;
+	}
+
+	if ((stat1 & DM9161_10BASE_T_FD) && (stat2 & DM9161_10FDX)) {
+		/*set MII for 10BaseT and Full Duplex  */
+		p_mac->EMAC_CFG = (p_mac->EMAC_CFG &
+				~(AT91C_EMAC_SPD | AT91C_EMAC_FD))
+				| AT91C_EMAC_FD;
+		return TRUE;
+	}
+
+	if ((stat1 & DM9161_100BASE_T4_HD) && (stat2 & DM9161_100HDX)) {
+		/*set MII for 100BaseTX and Half Duplex  */
+		p_mac->EMAC_CFG = (p_mac->EMAC_CFG &
+				~(AT91C_EMAC_SPD | AT91C_EMAC_FD))
+				| AT91C_EMAC_SPD;
+		return TRUE;
+	}
+
+	if ((stat1 & DM9161_10BASE_T_HD) && (stat2 & DM9161_10HDX)) {
+		/*set MII for 10BaseT and Half Duplex  */
+		p_mac->EMAC_CFG &= ~(AT91C_EMAC_SPD | AT91C_EMAC_FD);
+		return TRUE;
+	}
+	return FALSE;
+}
+
+
+/*
+ * Name:
+ *	dm9161_InitPhy
+ * Description:
+ *	MAC starts checking its link by using parallel detection and
+ *	Autonegotiation and the same is set in the MAC configuration registers
+ * Arguments:
+ *	p_mac - pointer to struct AT91S_EMAC
+ * Return value:
+ *	TRUE - if link status set succesfully
+ *	FALSE - if link status not set
+ */
+static UCHAR dm9161_InitPhy (AT91PS_EMAC p_mac)
+{
+	UCHAR ret = TRUE;
+	unsigned short IntValue;
+
+	at91rm9200_EmacEnableMDIO (p_mac);
+
+	if (!dm9161_GetLinkSpeed (p_mac)) {
+		/* Try another time */
+		ret = dm9161_GetLinkSpeed (p_mac);
+	}
+
+	/* Disable PHY Interrupts */
+	at91rm9200_EmacReadPhy (p_mac, DM9161_MDINTR, &IntValue);
+	/* clear FDX, SPD, Link, INTR masks */
+	IntValue &= ~(DM9161_FDX_MASK | DM9161_SPD_MASK |
+		      DM9161_LINK_MASK | DM9161_INTR_MASK);
+	at91rm9200_EmacWritePhy (p_mac, DM9161_MDINTR, &IntValue);
+	at91rm9200_EmacDisableMDIO (p_mac);
+
+	return (ret);
+}
+
+
+/*
+ * Name:
+ *	dm9161_AutoNegotiate
+ * Description:
+ *	MAC Autonegotiates with the partner status of same is set in the
+ *	MAC configuration registers
+ * Arguments:
+ *	dev - pointer to struct net_device
+ * Return value:
+ *	TRUE - if link status set successfully
+ *	FALSE - if link status not set
+ */
+static UCHAR dm9161_AutoNegotiate (AT91PS_EMAC p_mac, int *status)
+{
+	unsigned short value;
+	unsigned short PhyAnar;
+	unsigned short PhyAnalpar;
+
+	/* Set dm9161 control register */
+	if (!at91rm9200_EmacReadPhy (p_mac, DM9161_BMCR, &value))
+		return FALSE;
+	value &= ~DM9161_AUTONEG;	/* remove autonegotiation enable */
+	value |= DM9161_ISOLATE;	/* Electrically isolate PHY */
+	if (!at91rm9200_EmacWritePhy (p_mac, DM9161_BMCR, &value))
+		return FALSE;
+
+	/* Set the Auto_negotiation Advertisement Register */
+	/* MII advertising for Next page, 100BaseTxFD and HD, 10BaseTFD and HD, IEEE 802.3 */
+	PhyAnar = DM9161_NP | DM9161_TX_FDX | DM9161_TX_HDX |
+		  DM9161_10_FDX | DM9161_10_HDX | DM9161_AN_IEEE_802_3;
+	if (!at91rm9200_EmacWritePhy (p_mac, DM9161_ANAR, &PhyAnar))
+		return FALSE;
+
+	/* Read the Control Register     */
+	if (!at91rm9200_EmacReadPhy (p_mac, DM9161_BMCR, &value))
+		return FALSE;
+
+	value |= DM9161_SPEED_SELECT | DM9161_AUTONEG | DM9161_DUPLEX_MODE;
+	if (!at91rm9200_EmacWritePhy (p_mac, DM9161_BMCR, &value))
+		return FALSE;
+	/* Restart Auto_negotiation  */
+	value |= DM9161_RESTART_AUTONEG;
+	if (!at91rm9200_EmacWritePhy (p_mac, DM9161_BMCR, &value))
+		return FALSE;
+
+	/*check AutoNegotiate complete */
+	udelay (10000);
+	at91rm9200_EmacReadPhy (p_mac, DM9161_BMSR, &value);
+	if (!(value & DM9161_AUTONEG_COMP))
+		return FALSE;
+
+	/* Get the AutoNeg Link partner base page */
+	if (!at91rm9200_EmacReadPhy (p_mac, DM9161_ANLPAR, &PhyAnalpar))
+		return FALSE;
+
+	if ((PhyAnar & DM9161_TX_FDX) && (PhyAnalpar & DM9161_TX_FDX)) {
+		/*set MII for 100BaseTX and Full Duplex  */
+		p_mac->EMAC_CFG |= AT91C_EMAC_SPD | AT91C_EMAC_FD;
+		return TRUE;
+	}
+
+	if ((PhyAnar & DM9161_10_FDX) && (PhyAnalpar & DM9161_10_FDX)) {
+		/*set MII for 10BaseT and Full Duplex  */
+		p_mac->EMAC_CFG = (p_mac->EMAC_CFG &
+				~(AT91C_EMAC_SPD | AT91C_EMAC_FD))
+				| AT91C_EMAC_FD;
+		return TRUE;
+	}
+	return FALSE;
+}
+
+
+/*
+ * Name:
+ *	at91rm92000_GetPhyInterface
+ * Description:
+ *	Initialise the interface functions to the PHY
+ * Arguments:
+ *	None
+ * Return value:
+ *	None
+ */
+void at91rm92000_GetPhyInterface(AT91PS_PhyOps p_phyops)
+{
+	p_phyops->Init = dm9161_InitPhy;
+	p_phyops->IsPhyConnected = dm9161_IsPhyConnected;
+	p_phyops->GetLinkSpeed = dm9161_GetLinkSpeed;
+	p_phyops->AutoNegotiate = dm9161_AutoNegotiate;
+}
+
+#endif	/* CONFIG_COMMANDS & CFG_CMD_NET */
+
+#endif	/* CONFIG_DRIVER_ETHER */

board/cmc_pu2/flash.c

@@ -0,0 +1,507 @@
+/*
+ * (C) Copyright 2002
+ * Lineo, Inc. <www.lineo.com>
+ * Bernhard Kuhn <bkuhn@lineo.com>
+ *
+ * (C) Copyright 2002
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Alex Zuepke <azu@sysgo.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+
+ulong myflush(void);
+
+
+/* Flash Organization Structure */
+typedef struct OrgDef
+{
+	unsigned int sector_number;
+	unsigned int sector_size;
+} OrgDef;
+
+
+/* Flash Organizations */
+OrgDef OrgAT49BV16x4[] =
+{
+	{  8,  8*1024 },	/*   8 *  8 kBytes sectors */
+	{  2, 32*1024 },	/*   2 * 32 kBytes sectors */
+	{ 30, 64*1024 },	/*  30 * 64 kBytes sectors */
+};
+
+OrgDef OrgAT49BV16x4A[] =
+{
+	{  8,  8*1024 },	/*   8 *  8 kBytes sectors */
+	{ 31, 64*1024 },	/*  31 * 64 kBytes sectors */
+};
+
+OrgDef OrgAT49BV6416[] =
+{
+	{   8,  8*1024 },	/*   8 *  8 kBytes sectors */
+	{ 127, 64*1024 },	/* 127 * 64 kBytes sectors */
+};
+
+flash_info_t    flash_info[CFG_MAX_FLASH_BANKS];
+
+/* AT49BV1614A Codes */
+#define FLASH_CODE1		0xAA
+#define FLASH_CODE2		0x55
+#define ID_IN_CODE		0x90
+#define ID_OUT_CODE		0xF0
+
+
+#define CMD_READ_ARRAY		0x00F0
+#define CMD_UNLOCK1		0x00AA
+#define CMD_UNLOCK2		0x0055
+#define CMD_ERASE_SETUP		0x0080
+#define CMD_ERASE_CONFIRM	0x0030
+#define CMD_PROGRAM		0x00A0
+#define CMD_UNLOCK_BYPASS	0x0020
+#define CMD_SECTOR_UNLOCK	0x0070
+
+#define MEM_FLASH_ADDR1		(*(volatile u16 *)(CFG_FLASH_BASE + (0x00005555<<1)))
+#define MEM_FLASH_ADDR2		(*(volatile u16 *)(CFG_FLASH_BASE + (0x00002AAA<<1)))
+
+#define BIT_ERASE_DONE		0x0080
+#define BIT_RDY_MASK		0x0080
+#define BIT_PROGRAM_ERROR	0x0020
+#define BIT_TIMEOUT		0x80000000 /* our flag */
+
+#define READY 1
+#define ERR   2
+#define TMO   4
+
+/*-----------------------------------------------------------------------
+ */
+void flash_identification (flash_info_t * info)
+{
+	volatile u16 manuf_code, device_code, add_device_code;
+
+	MEM_FLASH_ADDR1 = FLASH_CODE1;
+	MEM_FLASH_ADDR2 = FLASH_CODE2;
+	MEM_FLASH_ADDR1 = ID_IN_CODE;
+
+	manuf_code = *(volatile u16 *) CFG_FLASH_BASE;
+	device_code = *(volatile u16 *) (CFG_FLASH_BASE + 2);
+	add_device_code = *(volatile u16 *) (CFG_FLASH_BASE + (3 << 1));
+
+	MEM_FLASH_ADDR1 = FLASH_CODE1;
+	MEM_FLASH_ADDR2 = FLASH_CODE2;
+	MEM_FLASH_ADDR1 = ID_OUT_CODE;
+
+	/* Vendor type */
+	info->flash_id = ATM_MANUFACT & FLASH_VENDMASK;
+	printf ("Atmel: ");
+
+	if ((device_code & FLASH_TYPEMASK) == (ATM_ID_BV1614 & FLASH_TYPEMASK)) {
+
+		if ((add_device_code & FLASH_TYPEMASK) ==
+			(ATM_ID_BV1614A & FLASH_TYPEMASK)) {
+			info->flash_id |= ATM_ID_BV1614A & FLASH_TYPEMASK;
+			printf ("AT49BV1614A (16Mbit)\n");
+		} else {				/* AT49BV1614 Flash */
+			info->flash_id |= ATM_ID_BV1614 & FLASH_TYPEMASK;
+			printf ("AT49BV1614 (16Mbit)\n");
+		}
+
+	} else if ((device_code & FLASH_TYPEMASK) == (ATM_ID_BV6416 & FLASH_TYPEMASK)) {
+		info->flash_id |= ATM_ID_BV6416 & FLASH_TYPEMASK;
+		printf ("AT49BV6416 (64Mbit)\n");
+	}
+}
+
+ushort flash_number_sector(OrgDef *pOrgDef, unsigned int nb_blocks)
+{
+	int i, nb_sectors = 0;
+
+	for (i=0; i<nb_blocks; i++){
+		nb_sectors += pOrgDef[i].sector_number;
+	}
+
+	return nb_sectors;
+}
+
+void flash_unlock_sector(flash_info_t * info, unsigned int sector)
+{
+	volatile u16 *addr = (volatile u16 *) (info->start[sector]);
+
+	MEM_FLASH_ADDR1 = CMD_UNLOCK1;
+	*addr = CMD_SECTOR_UNLOCK;
+}
+
+
+ulong flash_init (void)
+{
+	int i, j, k;
+	unsigned int flash_nb_blocks, sector;
+	unsigned int start_address;
+	OrgDef *pOrgDef;
+
+	ulong size = 0;
+
+	for (i = 0; i < CFG_MAX_FLASH_BANKS; i++) {
+		ulong flashbase = 0;
+
+		flash_identification (&flash_info[i]);
+
+		if ((flash_info[i].flash_id & FLASH_TYPEMASK) ==
+			(ATM_ID_BV1614 & FLASH_TYPEMASK)) {
+
+			pOrgDef = OrgAT49BV16x4;
+			flash_nb_blocks = sizeof (OrgAT49BV16x4) / sizeof (OrgDef);
+		} else if ((flash_info[i].flash_id & FLASH_TYPEMASK) ==
+			(ATM_ID_BV1614A & FLASH_TYPEMASK)){	/* AT49BV1614A Flash */
+
+			pOrgDef = OrgAT49BV16x4A;
+			flash_nb_blocks = sizeof (OrgAT49BV16x4A) / sizeof (OrgDef);
+		} else if ((flash_info[i].flash_id & FLASH_TYPEMASK) ==
+			(ATM_ID_BV6416 & FLASH_TYPEMASK)){	/* AT49BV6416 Flash */
+
+			pOrgDef = OrgAT49BV6416;
+			flash_nb_blocks = sizeof (OrgAT49BV6416) / sizeof (OrgDef);
+		} else {
+			flash_nb_blocks = 0;
+			pOrgDef = OrgAT49BV16x4;
+		}
+
+		flash_info[i].sector_count = flash_number_sector(pOrgDef, flash_nb_blocks);
+		memset (flash_info[i].protect, 0, flash_info[i].sector_count);
+
+		if (i == 0)
+			flashbase = PHYS_FLASH_1;
+		else
+			panic ("configured too many flash banks!\n");
+
+		sector = 0;
+		start_address = flashbase;
+		flash_info[i].size = 0;
+
+		for (j = 0; j < flash_nb_blocks; j++) {
+			for (k = 0; k < pOrgDef[j].sector_number; k++) {
+				flash_info[i].start[sector++] = start_address;
+				start_address += pOrgDef[j].sector_size;
+				flash_info[i].size += pOrgDef[j].sector_size;
+			}
+		}
+
+		size += flash_info[i].size;
+
+		if ((flash_info[i].flash_id & FLASH_TYPEMASK) ==
+			(ATM_ID_BV6416 & FLASH_TYPEMASK)){	/* AT49BV6416 Flash */
+
+			/* Unlock all sectors at reset */
+			for (j=0; j<flash_info[i].sector_count; j++){
+				flash_unlock_sector(&flash_info[i], j);
+			}
+		}
+	}
+
+	/* Protect binary boot image */
+	flash_protect (FLAG_PROTECT_SET,
+		       CFG_FLASH_BASE,
+		       CFG_FLASH_BASE + CFG_BOOT_SIZE - 1, &flash_info[0]);
+
+	/* Protect environment variables */
+	flash_protect (FLAG_PROTECT_SET,
+		       CFG_ENV_ADDR,
+		       CFG_ENV_ADDR + CFG_ENV_SIZE - 1, &flash_info[0]);
+
+	/* Protect U-Boot gzipped image */
+	flash_protect (FLAG_PROTECT_SET,
+		       CFG_U_BOOT_BASE,
+		       CFG_U_BOOT_BASE + CFG_U_BOOT_SIZE - 1, &flash_info[0]);
+
+	return size;
+}
+
+/*-----------------------------------------------------------------------
+ */
+void flash_print_info (flash_info_t * info)
+{
+	int i;
+
+	switch (info->flash_id & FLASH_VENDMASK) {
+	case (ATM_MANUFACT & FLASH_VENDMASK):
+		printf ("Atmel: ");
+		break;
+	default:
+		printf ("Unknown Vendor ");
+		break;
+	}
+
+	switch (info->flash_id & FLASH_TYPEMASK) {
+	case (ATM_ID_BV1614 & FLASH_TYPEMASK):
+		printf ("AT49BV1614 (16Mbit)\n");
+		break;
+	case (ATM_ID_BV1614A & FLASH_TYPEMASK):
+		printf ("AT49BV1614A (16Mbit)\n");
+		break;
+	case (ATM_ID_BV6416 & FLASH_TYPEMASK):
+		printf ("AT49BV6416 (64Mbit)\n");
+		break;
+	default:
+		printf ("Unknown Chip Type\n");
+		goto Done;
+		break;
+	}
+
+	printf ("  Size: %ld MB in %d Sectors\n",
+		info->size >> 20, info->sector_count);
+
+	printf ("  Sector Start Addresses:");
+	for (i = 0; i < info->sector_count; i++) {
+		if ((i % 5) == 0) {
+			printf ("\n   ");
+		}
+		printf (" %08lX%s", info->start[i],
+			info->protect[i] ? " (RO)" : "     ");
+	}
+	printf ("\n");
+
+Done:	;
+}
+
+/*-----------------------------------------------------------------------
+ */
+
+int flash_erase (flash_info_t * info, int s_first, int s_last)
+{
+	ulong result;
+	int iflag, cflag, prot, sect;
+	int rc = ERR_OK;
+	int chip1;
+
+	/* first look for protection bits */
+
+	if (info->flash_id == FLASH_UNKNOWN)
+		return ERR_UNKNOWN_FLASH_TYPE;
+
+	if ((s_first < 0) || (s_first > s_last)) {
+		return ERR_INVAL;
+	}
+
+	if ((info->flash_id & FLASH_VENDMASK) !=
+		(ATM_MANUFACT & FLASH_VENDMASK)) {
+		return ERR_UNKNOWN_FLASH_VENDOR;
+	}
+
+	prot = 0;
+	for (sect = s_first; sect <= s_last; ++sect) {
+		if (info->protect[sect]) {
+			prot++;
+		}
+	}
+	if (prot)
+		return ERR_PROTECTED;
+
+	/*
+	 * Disable interrupts which might cause a timeout
+	 * here. Remember that our exception vectors are
+	 * at address 0 in the flash, and we don't want a
+	 * (ticker) exception to happen while the flash
+	 * chip is in programming mode.
+	 */
+	cflag = icache_status ();
+	icache_disable ();
+	iflag = disable_interrupts ();
+
+	/* Start erase on unprotected sectors */
+	for (sect = s_first; sect <= s_last && !ctrlc (); sect++) {
+		printf ("Erasing sector %2d ... ", sect);
+
+		/* arm simple, non interrupt dependent timer */
+		reset_timer_masked ();
+
+		if (info->protect[sect] == 0) {	/* not protected */
+			volatile u16 *addr = (volatile u16 *) (info->start[sect]);
+
+			MEM_FLASH_ADDR1 = CMD_UNLOCK1;
+			MEM_FLASH_ADDR2 = CMD_UNLOCK2;
+			MEM_FLASH_ADDR1 = CMD_ERASE_SETUP;
+
+			MEM_FLASH_ADDR1 = CMD_UNLOCK1;
+			MEM_FLASH_ADDR2 = CMD_UNLOCK2;
+			*addr = CMD_ERASE_CONFIRM;
+
+			/* wait until flash is ready */
+			chip1 = 0;
+
+			do {
+				result = *addr;
+
+				/* check timeout */
+				if (get_timer_masked () > CFG_FLASH_ERASE_TOUT) {
+					MEM_FLASH_ADDR1 = CMD_READ_ARRAY;
+					chip1 = TMO;
+					break;
+				}
+
+				if (!chip1 && (result & 0xFFFF) & BIT_ERASE_DONE)
+					chip1 = READY;
+
+			} while (!chip1);
+
+			MEM_FLASH_ADDR1 = CMD_READ_ARRAY;
+
+			if (chip1 == ERR) {
+				rc = ERR_PROG_ERROR;
+				goto outahere;
+			}
+			if (chip1 == TMO) {
+				rc = ERR_TIMOUT;
+				goto outahere;
+			}
+
+			printf ("ok.\n");
+		} else {			/* it was protected */
+			printf ("protected!\n");
+		}
+	}
+
+	if (ctrlc ())
+		printf ("User Interrupt!\n");
+
+outahere:
+	/* allow flash to settle - wait 10 ms */
+	udelay_masked (10000);
+
+	if (iflag)
+		enable_interrupts ();
+
+	if (cflag)
+		icache_enable ();
+
+	return rc;
+}
+
+/*-----------------------------------------------------------------------
+ * Copy memory to flash
+ */
+
+volatile static int write_word (flash_info_t * info, ulong dest,
+								ulong data)
+{
+	volatile u16 *addr = (volatile u16 *) dest;
+	ulong result;
+	int rc = ERR_OK;
+	int cflag, iflag;
+	int chip1;
+
+	/*
+	 * Check if Flash is (sufficiently) erased
+	 */
+	result = *addr;
+	if ((result & data) != data)
+		return ERR_NOT_ERASED;
+
+
+	/*
+	 * Disable interrupts which might cause a timeout
+	 * here. Remember that our exception vectors are
+	 * at address 0 in the flash, and we don't want a
+	 * (ticker) exception to happen while the flash
+	 * chip is in programming mode.
+	 */
+	cflag = icache_status ();
+	icache_disable ();
+	iflag = disable_interrupts ();
+
+	MEM_FLASH_ADDR1 = CMD_UNLOCK1;
+	MEM_FLASH_ADDR2 = CMD_UNLOCK2;
+	MEM_FLASH_ADDR1 = CMD_PROGRAM;
+	*addr = data;
+
+	/* arm simple, non interrupt dependent timer */
+	reset_timer_masked ();
+
+	/* wait until flash is ready */
+	chip1 = 0;
+	do {
+		result = *addr;
+
+		/* check timeout */
+		if (get_timer_masked () > CFG_FLASH_ERASE_TOUT) {
+			chip1 = ERR | TMO;
+			break;
+		}
+		if (!chip1 && ((result & 0x80) == (data & 0x80)))
+			chip1 = READY;
+
+	} while (!chip1);
+
+	*addr = CMD_READ_ARRAY;
+
+	if (chip1 == ERR || *addr != data)
+		rc = ERR_PROG_ERROR;
+
+	if (iflag)
+		enable_interrupts ();
+
+	if (cflag)
+		icache_enable ();
+
+	return rc;
+}
+
+/*-----------------------------------------------------------------------
+ * Copy memory to flash.
+ */
+
+int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt)
+{
+	ulong wp, data;
+	int rc;
+
+	if (addr & 1) {
+		printf ("unaligned destination not supported\n");
+		return ERR_ALIGN;
+	};
+
+	if ((int) src & 1) {
+		printf ("unaligned source not supported\n");
+		return ERR_ALIGN;
+	};
+
+	wp = addr;
+
+	while (cnt >= 2) {
+		data = *((volatile u16 *) src);
+		if ((rc = write_word (info, wp, data)) != 0) {
+			return (rc);
+		}
+		src += 2;
+		wp += 2;
+		cnt -= 2;
+	}
+
+	if (cnt == 1) {
+		data = (*((volatile u8 *) src)) | (*((volatile u8 *) (wp + 1)) <<
+										   8);
+		if ((rc = write_word (info, wp, data)) != 0) {
+			return (rc);
+		}
+		src += 1;
+		wp += 1;
+		cnt -= 1;
+	};
+
+	return ERR_OK;
+}

board/cmc_pu2/memsetup.S

@@ -0,0 +1,200 @@
+/*
+ * Memory Setup stuff - taken from blob memsetup.S
+ *
+ * Copyright (C) 1999 2000 2001 Erik Mouw (J.A.K.Mouw@its.tudelft.nl) and
+ *		       Jan-Derk Bakker (J.D.Bakker@its.tudelft.nl)
+ *
+ * Modified for the at91rm9200dk board by
+ * (C) Copyright 2004
+ * Gary Jennejohn, DENX Software Engineering, <gj@denx.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <version.h>
+
+#ifdef CONFIG_BOOTBINFUNC
+/*
+ * some parameters for the board
+ *
+ * This is based on rm9200dk.cfg for the BDI2000 from ABATRON which in
+ * turn is based on the boot.bin code from ATMMEL
+ *
+ */
+
+/* flash */
+#define MC_PUIA 0xFFFFFF10
+#define MC_PUIA_VAL 0x00000000
+#define MC_PUP 0xFFFFFF50
+#define MC_PUP_VAL 0x00000000
+#define MC_PUER 0xFFFFFF54
+#define MC_PUER_VAL 0x00000000
+#define MC_ASR 0xFFFFFF04
+#define MC_ASR_VAL 0x00000000
+#define MC_AASR 0xFFFFFF08
+#define MC_AASR_VAL 0x00000000
+#define EBI_CFGR 0xFFFFFF64
+#define EBI_CFGR_VAL 0x00000000
+#define SMC2_CSR 0xFFFFFF70
+#define SMC2_CSR_VAL 0x00003284 /* 16bit, 2 TDF, 4 WS */
+
+/* clocks */
+#define PLLAR 0xFFFFFC28
+#define PLLAR_VAL 0x20263E04 /* 179.712000 MHz for PCK */
+#define PLLBR 0xFFFFFC2C
+#define PLLBR_VAL 0x10483E0E /* 48.054857 MHz (divider by 2 for USB) */
+#define MCKR 0xFFFFFC30
+#define MCKR_VAL 0x00000202 /* PCK/3 = MCK Master Clock = 59.904000MHz from PLLA */
+
+/* sdram */
+#define PIOC_ASR 0xFFFFF870
+#define PIOC_ASR_VAL 0xFFFF0000 /* Configure PIOC as peripheral (D16/D31) */
+#define PIOC_BSR 0xFFFFF804
+#define PIOC_BSR_VAL 0x00000000
+#define PIOC_PDR 0xFFFFF804
+#define PIOC_PDR_VAL 0xFFFF0000
+#define EBI_CSA 0xFFFFFF60
+#define EBI_CSA_VAL 0x00000002 /* CS1=SDRAM */
+#define SDRC_CR 0xFFFFFF98
+#define SDRC_CR_VAL 0x2188c155
+#define SDRAM 0x20000000 /* address of the SDRAM */
+#define SDRAM1 0x20000080 /* address of the SDRAM */
+#define SDRAM_VAL 0x00000000 /* value written to SDRAM */
+#define SDRC_MR 0xFFFFFF90
+#define SDRC_MR_VAL 0x00000002 /* Precharge All */
+#define SDRC_MR_VAL1 0x00000004 /* refresh */
+#define SDRC_MR_VAL2 0x00000003 /* Load Mode Register */
+#define SDRC_MR_VAL3 0x00000000 /* Normal Mode */
+#define SDRC_TR 0xFFFFFF94
+#define SDRC_TR_VAL 0x000002E0 /* Write refresh rate */
+
+
+_TEXT_BASE:
+	.word	TEXT_BASE
+
+.globl memsetup
+memsetup:
+	/* memory control configuration */
+	/* this isn't very elegant, but	 what the heck */
+	ldr	r0, =SMRDATA
+	ldr	r1, _TEXT_BASE
+	sub	r0, r0, r1
+	add	r2, r0, #80
+0:
+	/* the address */
+	ldr	r1, [r0], #4
+	/* the value */
+	ldr	r3, [r0], #4
+	str	r3, [r1]
+	cmp	r2, r0
+	bne	0b
+	/* delay - this is all done by guess */
+	ldr	r0, =0x00001000
+1:
+	subs	r0, r0, #1
+	bhi	1b
+	ldr	r0, =SMRDATA1
+	ldr	r1, _TEXT_BASE
+	sub	r0, r0, r1
+	add	r2, r0, #176
+2:
+	/* the address */
+	ldr	r1, [r0], #4
+	/* the value */
+	ldr	r3, [r0], #4
+	str	r3, [r1]
+	cmp	r2, r0
+	bne	2b
+
+	/* everything is fine now */
+	mov	pc, lr
+
+	.ltorg
+
+SMRDATA:
+	.word MC_PUIA
+	.word MC_PUIA_VAL
+	.word MC_PUP
+	.word MC_PUP_VAL
+	.word MC_PUER
+	.word MC_PUER_VAL
+	.word MC_ASR
+	.word MC_ASR_VAL
+	.word MC_AASR
+	.word MC_AASR_VAL
+	.word EBI_CFGR
+	.word EBI_CFGR_VAL
+	.word SMC2_CSR
+	.word SMC2_CSR_VAL
+	.word PLLAR
+	.word PLLAR_VAL
+	.word PLLBR
+	.word PLLBR_VAL
+	.word MCKR
+	.word MCKR_VAL
+	/* SMRDATA is 80 bytes long */
+	/* here there's a delay of 100 */
+SMRDATA1:
+	.word PIOC_ASR
+	.word PIOC_ASR_VAL
+	.word PIOC_BSR
+	.word PIOC_BSR_VAL
+	.word PIOC_PDR
+	.word PIOC_PDR_VAL
+	.word EBI_CSA
+	.word EBI_CSA_VAL
+	.word SDRC_CR
+	.word SDRC_CR_VAL
+	.word SDRC_MR
+	.word SDRC_MR_VAL
+	.word SDRAM
+	.word SDRAM_VAL
+	.word SDRC_MR
+	.word SDRC_MR_VAL1
+	.word SDRAM
+	.word SDRAM_VAL
+	.word SDRAM
+	.word SDRAM_VAL
+	.word SDRAM
+	.word SDRAM_VAL
+	.word SDRAM
+	.word SDRAM_VAL
+	.word SDRAM
+	.word SDRAM_VAL
+	.word SDRAM
+	.word SDRAM_VAL
+	.word SDRAM
+	.word SDRAM_VAL
+	.word SDRAM
+	.word SDRAM_VAL
+	.word SDRC_MR
+	.word SDRC_MR_VAL2
+	.word SDRAM1
+	.word SDRAM_VAL
+	.word SDRC_TR
+	.word SDRC_TR_VAL
+	.word SDRAM
+	.word SDRAM_VAL
+	.word SDRC_MR
+	.word SDRC_MR_VAL3
+	.word SDRAM
+	.word SDRAM_VAL
+	/* SMRDATA1 is 176 bytes long */
+#endif /* CONFIG_BOOTBINFUNC */

board/cmc_pu2/u-boot.lds

@@ -0,0 +1,56 @@
+/*
+ * (C) Copyright 2002
+ * Gary Jennejohn, DENX Software Engineering, <gj@denx.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+/*OUTPUT_FORMAT("elf32-arm", "elf32-arm", "elf32-arm")*/
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+	. = 0x00000000;
+
+	. = ALIGN(4);
+	.text      :
+	{
+	  cpu/at91rm9200/start.o	(.text)
+	  *(.text)
+	}
+
+	. = ALIGN(4);
+	.rodata : { *(.rodata) }
+
+	. = ALIGN(4);
+	.data : { *(.data) }
+
+	. = ALIGN(4);
+	.got : { *(.got) }
+
+	__u_boot_cmd_start = .;
+	.u_boot_cmd : { *(.u_boot_cmd) }
+	__u_boot_cmd_end = .;
+
+	. = ALIGN(4);
+	__bss_start = .;
+	.bss : { *(.bss) }
+	_end = .;
+}

board/cogent/mb.h

@@ -54,7 +54,7 @@
  * i.e. they are 8 bytes apart. For big endian addressing, the 8 bit register
  * will be at byte 7 (the address + 7). For little endian addressing, the
  * register will be at byte 0 (the address + 0). To learn the endianess
- * we must include <asm/byteorder.h>
+ * we must include <endian.h>
  *
  * Take the CMA102 and CMA111 motherboards as examples...
  *
@@ -230,16 +230,20 @@
 
 #ifndef __ASSEMBLY__
 
-#include <asm/byteorder.h>
+#ifdef USE_HOSTCC
+#include <endian.h>		/* avoid using private kernel header files */
+#else
+#include <asm/byteorder.h>	/* use U-Boot provided headers */
+#endif
 
 /* a single CMA10x motherboard i/o register */
 typedef
     struct {
-#if defined(__LITTLE_ENDIAN)
+#if __BYTE_ORDER == __LITTLE_ENDIAN
 	unsigned char value;
 #endif
 	unsigned char filler[7];
-#if defined(__BIG_ENDIAN)
+#if __BYTE_ORDER == __BIG_ENDIAN
 	unsigned char value;
 #endif
     }
@@ -357,7 +361,7 @@ cma_mb_dipsw;
 /* V360EPC PCI Bridge */
 typedef
     struct {
-#if defined(__LITTLE_ENDIAN)
+#if __BYTE_ORDER == __LITTLE_ENDIAN
 	unsigned short v3_pci_vendor;		/* 0x00 */
 	unsigned short v3_pci_device;
 	unsigned short v3_pci_cmd;		/* 0x04 */
@@ -436,7 +440,7 @@ typedef
 	unsigned long  reserved8:24;
 	unsigned long  reserved9[7];		/* 0xe4 */
 #endif
-#if defined(__BIG_ENDIAN)
+#if __BYTE_ORDER == __BIG_ENDIAN
 	unsigned short v3_pci_device;		/* 0x00 */
 	unsigned short v3_pci_vendor;
 	unsigned short v3_pci_stat;		/* 0x04 */

board/cradle/cradle.c

@@ -186,7 +186,7 @@ board_init (void)
 	led_code (0xf, YELLOW);
 
 	/* arch number of HHP Cradle */
-	gd->bd->bi_arch_number = 174;
+	gd->bd->bi_arch_number = MACH_TYPE_HHP_CRADLE;
 
 	/* adress of boot parameters */
 	gd->bd->bi_boot_params = 0xa0000100;

board/cradle/flash.c

@@ -30,338 +30,330 @@
 #define FLASH_BANK_SIZE 0x400000
 #define MAIN_SECT_SIZE  0x20000
 
-flash_info_t    flash_info[CFG_MAX_FLASH_BANKS];
+flash_info_t flash_info[CFG_MAX_FLASH_BANKS];
 
 
 /*-----------------------------------------------------------------------
  */
 
-ulong flash_init(void)
+ulong flash_init (void)
 {
-   int i, j;
-   ulong size = 0;
+	int i, j;
+	ulong size = 0;
 
-   for (i = 0; i < CFG_MAX_FLASH_BANKS; i++)
-   {
-      ulong flashbase = 0;
-      flash_info[i].flash_id =
-	  (INTEL_MANUFACT & FLASH_VENDMASK) |
-	  (INTEL_ID_28F128J3 & FLASH_TYPEMASK);
-      flash_info[i].size = FLASH_BANK_SIZE;
-      flash_info[i].sector_count = CFG_MAX_FLASH_SECT;
-      memset(flash_info[i].protect, 0, CFG_MAX_FLASH_SECT);
-      switch (i)
-      {
-	 case 0:
-		flashbase = PHYS_FLASH_1;
-		break;
-	 case 1:
-		flashbase = PHYS_FLASH_2;
-		break;
-	 default:
-		panic("configured too many flash banks!\n");
-		break;
-      }
-      for (j = 0; j < flash_info[i].sector_count; j++)
-      {
-	 flash_info[i].start[j] = flashbase + j*MAIN_SECT_SIZE;
-      }
-      size += flash_info[i].size;
-   }
+	for (i = 0; i < CFG_MAX_FLASH_BANKS; i++) {
+		ulong flashbase = 0;
 
-   /* Protect monitor and environment sectors
-    */
-   flash_protect(FLAG_PROTECT_SET,
-		  CFG_FLASH_BASE,
-		  CFG_FLASH_BASE + monitor_flash_len - 1,
-		  &flash_info[0]);
+		flash_info[i].flash_id =
+			(INTEL_MANUFACT & FLASH_VENDMASK) |
+			(INTEL_ID_28F128J3 & FLASH_TYPEMASK);
+		flash_info[i].size = FLASH_BANK_SIZE;
+		flash_info[i].sector_count = CFG_MAX_FLASH_SECT;
+		memset (flash_info[i].protect, 0, CFG_MAX_FLASH_SECT);
+		switch (i) {
+		case 0:
+			flashbase = PHYS_FLASH_1;
+			break;
+		case 1:
+			flashbase = PHYS_FLASH_2;
+			break;
+		default:
+			panic ("configured too many flash banks!\n");
+			break;
+		}
+		for (j = 0; j < flash_info[i].sector_count; j++) {
+			flash_info[i].start[j] =
+				flashbase + j * MAIN_SECT_SIZE;
+		}
+		size += flash_info[i].size;
+	}
 
-   flash_protect(FLAG_PROTECT_SET,
-		  CFG_ENV_ADDR,
-		  CFG_ENV_ADDR + CFG_ENV_SIZE - 1,
-		  &flash_info[0]);
+	/* Protect monitor and environment sectors
+	 */
+	flash_protect (FLAG_PROTECT_SET,
+		       CFG_FLASH_BASE,
+		       CFG_FLASH_BASE + monitor_flash_len - 1,
+		       &flash_info[0]);
 
-   return size;
+	flash_protect (FLAG_PROTECT_SET,
+		       CFG_ENV_ADDR,
+		       CFG_ENV_ADDR + CFG_ENV_SIZE - 1, &flash_info[0]);
+
+	return size;
 }
 
 /*-----------------------------------------------------------------------
  */
-void flash_print_info  (flash_info_t *info)
+void flash_print_info (flash_info_t * info)
 {
-   int i, j;
+	int i, j;
 
-   for (j=0; j<CFG_MAX_FLASH_BANKS; j++)
-   {
-      switch (info->flash_id & FLASH_VENDMASK)
-      {
-	 case (INTEL_MANUFACT & FLASH_VENDMASK):
-		printf("Intel: ");
-		break;
-	 default:
-		printf("Unknown Vendor ");
-		break;
-      }
+	for (j = 0; j < CFG_MAX_FLASH_BANKS; j++) {
+		switch (info->flash_id & FLASH_VENDMASK) {
+		case (INTEL_MANUFACT & FLASH_VENDMASK):
+			printf ("Intel: ");
+			break;
+		default:
+			printf ("Unknown Vendor ");
+			break;
+		}
 
-      switch (info->flash_id & FLASH_TYPEMASK)
-      {
-	 case (INTEL_ID_28F320J3A & FLASH_TYPEMASK):
-		printf("28F320J3A (32Mbit)\n");
-		break;
-	 case (INTEL_ID_28F128J3 & FLASH_TYPEMASK):
-		printf("28F128J3 (128Mbit)\n");
-		break;
-	 default:
-		printf("Unknown Chip Type\n");
-		goto Done;
-		break;
-      }
+		switch (info->flash_id & FLASH_TYPEMASK) {
+		case (INTEL_ID_28F320J3A & FLASH_TYPEMASK):
+			printf ("28F320J3A (32Mbit)\n");
+			break;
+		case (INTEL_ID_28F128J3 & FLASH_TYPEMASK):
+			printf ("28F128J3 (128Mbit)\n");
+			break;
+		default:
+			printf ("Unknown Chip Type\n");
+			goto Done;
+			break;
+		}
 
-      printf("  Size: %ld MB in %d Sectors\n",
-		info->size >> 20, info->sector_count);
+		printf ("  Size: %ld MB in %d Sectors\n",
+			info->size >> 20, info->sector_count);
 
-      printf("  Sector Start Addresses:");
-      for (i = 0; i < info->sector_count; i++)
-      {
-	 if ((i % 5) == 0)
-	 {
-	    printf ("\n   ");
-	 }
-	 printf (" %08lX%s", info->start[i],
-			info->protect[i] ? " (RO)" : "     ");
-      }
-      printf ("\n");
-      info++;
-   }
+		printf ("  Sector Start Addresses:");
+		for (i = 0; i < info->sector_count; i++) {
+			if ((i % 5) == 0) {
+				printf ("\n   ");
+			}
+			printf (" %08lX%s", info->start[i],
+				info->protect[i] ? " (RO)" : "     ");
+		}
+		printf ("\n");
+		info++;
+	}
 
-Done:
+Done:	;
 }
 
 /*-----------------------------------------------------------------------
  */
 
-int        flash_erase (flash_info_t *info, int s_first, int s_last)
+int flash_erase (flash_info_t * info, int s_first, int s_last)
 {
-   int flag, prot, sect;
-   int rc = ERR_OK;
+	int flag, prot, sect;
+	int rc = ERR_OK;
 
-   if (info->flash_id == FLASH_UNKNOWN)
-	return ERR_UNKNOWN_FLASH_TYPE;
+	if (info->flash_id == FLASH_UNKNOWN)
+		return ERR_UNKNOWN_FLASH_TYPE;
 
-   if ((s_first < 0) || (s_first > s_last)) {
-	return ERR_INVAL;
-   }
+	if ((s_first < 0) || (s_first > s_last)) {
+		return ERR_INVAL;
+	}
 
-   if ((info->flash_id & FLASH_VENDMASK) !=
-	(INTEL_MANUFACT & FLASH_VENDMASK)) {
-	return ERR_UNKNOWN_FLASH_VENDOR;
-   }
+	if ((info->flash_id & FLASH_VENDMASK) !=
+	    (INTEL_MANUFACT & FLASH_VENDMASK)) {
+		return ERR_UNKNOWN_FLASH_VENDOR;
+	}
 
-   prot = 0;
-   for (sect=s_first; sect<=s_last; ++sect) {
-      if (info->protect[sect]) {
-	    prot++;
-      }
-   }
-   if (prot)
-	return ERR_PROTECTED;
+	prot = 0;
+	for (sect = s_first; sect <= s_last; ++sect) {
+		if (info->protect[sect]) {
+			prot++;
+		}
+	}
+	if (prot)
+		return ERR_PROTECTED;
 
-   /*
-    * Disable interrupts which might cause a timeout
-    * here. Remember that our exception vectors are
-    * at address 0 in the flash, and we don't want a
-    * (ticker) exception to happen while the flash
-    * chip is in programming mode.
-    */
-   flag = disable_interrupts();
+	/*
+	 * Disable interrupts which might cause a timeout
+	 * here. Remember that our exception vectors are
+	 * at address 0 in the flash, and we don't want a
+	 * (ticker) exception to happen while the flash
+	 * chip is in programming mode.
+	 */
+	flag = disable_interrupts ();
 
-   /* Start erase on unprotected sectors */
-   for (sect = s_first; sect<=s_last && !ctrlc(); sect++) {
+	/* Start erase on unprotected sectors */
+	for (sect = s_first; sect <= s_last && !ctrlc (); sect++) {
 
-      printf("Erasing sector %2d ... ", sect);
+		printf ("Erasing sector %2d ... ", sect);
 
-      /* arm simple, non interrupt dependent timer */
-      reset_timer_masked();
+		/* arm simple, non interrupt dependent timer */
+		reset_timer_masked ();
 
-      if (info->protect[sect] == 0) {        /* not protected */
-	  vu_short *addr = (vu_short *)(info->start[sect]);
+		if (info->protect[sect] == 0) {	/* not protected */
+			vu_short *addr = (vu_short *) (info->start[sect]);
 
-	  *addr = 0x20;        /* erase setup */
-	  *addr = 0xD0;        /* erase confirm */
+			*addr = 0x20;	/* erase setup */
+			*addr = 0xD0;	/* erase confirm */
 
-	  while ((*addr & 0x80) != 0x80) {
-	     if (get_timer_masked() > CFG_FLASH_ERASE_TOUT) {
-		*addr = 0xB0; /* suspend erase */
-		*addr = 0xFF;        /* reset to read mode */
-		rc = ERR_TIMOUT;
-		goto outahere;
-	     }
-	  }
+			while ((*addr & 0x80) != 0x80) {
+				if (get_timer_masked () >
+				    CFG_FLASH_ERASE_TOUT) {
+					*addr = 0xB0;	/* suspend erase */
+					*addr = 0xFF;	/* reset to read mode */
+					rc = ERR_TIMOUT;
+					goto outahere;
+				}
+			}
 
-	  /* clear status register command */
-	  *addr = 0x50;
-	  /* reset to read mode */
-	  *addr = 0xFF;
-      }
-      printf("ok.\n");
-   }
-   if (ctrlc())
-      printf("User Interrupt!\n");
+			/* clear status register command */
+			*addr = 0x50;
+			/* reset to read mode */
+			*addr = 0xFF;
+		}
+		printf ("ok.\n");
+	}
+	if (ctrlc ())
+		printf ("User Interrupt!\n");
 
 outahere:
 
-   /* allow flash to settle - wait 10 ms */
-   udelay_masked(10000);
+	/* allow flash to settle - wait 10 ms */
+	udelay_masked (10000);
 
-   if (flag)
-      enable_interrupts();
+	if (flag)
+		enable_interrupts ();
 
-   return rc;
+	return rc;
 }
 
 /*-----------------------------------------------------------------------
  * Copy memory to flash
  */
 
-static int write_word (flash_info_t *info, ulong dest, ushort data)
+static int write_word (flash_info_t * info, ulong dest, ushort data)
 {
-   vu_short *addr = (vu_short *)dest, val;
-   int rc = ERR_OK;
-   int flag;
+	vu_short *addr = (vu_short *) dest, val;
+	int rc = ERR_OK;
+	int flag;
 
-   /* Check if Flash is (sufficiently) erased
-    */
-   if ((*addr & data) != data)
-      return ERR_NOT_ERASED;
+	/* Check if Flash is (sufficiently) erased
+	 */
+	if ((*addr & data) != data)
+		return ERR_NOT_ERASED;
 
-   /*
-    * Disable interrupts which might cause a timeout
-    * here. Remember that our exception vectors are
-    * at address 0 in the flash, and we don't want a
-    * (ticker) exception to happen while the flash
-    * chip is in programming mode.
-    */
-   flag = disable_interrupts();
+	/*
+	 * Disable interrupts which might cause a timeout
+	 * here. Remember that our exception vectors are
+	 * at address 0 in the flash, and we don't want a
+	 * (ticker) exception to happen while the flash
+	 * chip is in programming mode.
+	 */
+	flag = disable_interrupts ();
 
-   /* clear status register command */
-   *addr = 0x50;
+	/* clear status register command */
+	*addr = 0x50;
 
-   /* program set-up command */
-   *addr = 0x40;
+	/* program set-up command */
+	*addr = 0x40;
 
-   /* latch address/data */
-   *addr = data;
+	/* latch address/data */
+	*addr = data;
 
-   /* arm simple, non interrupt dependent timer */
-   reset_timer_masked();
+	/* arm simple, non interrupt dependent timer */
+	reset_timer_masked ();
 
-   /* wait while polling the status register */
-   while(((val = *addr) & 0x80) != 0x80)
-   {
-      if (get_timer_masked() > CFG_FLASH_WRITE_TOUT) {
-	  rc = ERR_TIMOUT;
-	  /* suspend program command */
-	  *addr = 0xB0;
-	  goto outahere;
-      }
-   }
+	/* wait while polling the status register */
+	while (((val = *addr) & 0x80) != 0x80) {
+		if (get_timer_masked () > CFG_FLASH_WRITE_TOUT) {
+			rc = ERR_TIMOUT;
+			/* suspend program command */
+			*addr = 0xB0;
+			goto outahere;
+		}
+	}
 
-   if(val & 0x1A) {        /* check for error */
-      printf("\nFlash write error %02x at address %08lx\n",
-	       (int)val, (unsigned long)dest);
-      if(val & (1<<3)) {
-	 printf("Voltage range error.\n");
-	 rc = ERR_PROG_ERROR;
-	 goto outahere;
-      }
-      if(val & (1<<1)) {
-	 printf("Device protect error.\n");
-	 rc = ERR_PROTECTED;
-	 goto outahere;
-      }
-      if(val & (1<<4)) {
-	 printf("Programming error.\n");
-	 rc = ERR_PROG_ERROR;
-	 goto outahere;
-      }
-      rc = ERR_PROG_ERROR;
-      goto outahere;
-   }
+	if (val & 0x1A) {	/* check for error */
+		printf ("\nFlash write error %02x at address %08lx\n",
+			(int) val, (unsigned long) dest);
+		if (val & (1 << 3)) {
+			printf ("Voltage range error.\n");
+			rc = ERR_PROG_ERROR;
+			goto outahere;
+		}
+		if (val & (1 << 1)) {
+			printf ("Device protect error.\n");
+			rc = ERR_PROTECTED;
+			goto outahere;
+		}
+		if (val & (1 << 4)) {
+			printf ("Programming error.\n");
+			rc = ERR_PROG_ERROR;
+			goto outahere;
+		}
+		rc = ERR_PROG_ERROR;
+		goto outahere;
+	}
 
 outahere:
-   /* read array command */
-   *addr = 0xFF;
+	/* read array command */
+	*addr = 0xFF;
 
-   if (flag)
-      enable_interrupts();
+	if (flag)
+		enable_interrupts ();
 
-   return rc;
+	return rc;
 }
 
 /*-----------------------------------------------------------------------
  * Copy memory to flash.
  */
 
-int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
+int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt)
 {
-   ulong cp, wp;
-   ushort data;
-   int l;
-   int i, rc;
+	ulong cp, wp;
+	ushort data;
+	int l;
+	int i, rc;
 
-   wp = (addr & ~1);        /* get lower word aligned address */
+	wp = (addr & ~1);	/* get lower word aligned address */
 
-   /*
-    * handle unaligned start bytes
-    */
-   if ((l = addr - wp) != 0)
-   {
-      data = 0;
-      for (i=0, cp=wp; i<l; ++i, ++cp) {
-	   data = (data >> 8) | (*(uchar *)cp << 8);
-      }
-      for (; i<2 && cnt>0; ++i) {
-	 data = (data >> 8) | (*src++ << 8);
-	 --cnt;
-	 ++cp;
-      }
-      for (; cnt==0 && i<2; ++i, ++cp) {
-	 data = (data >> 8) | (*(uchar *)cp << 8);
-      }
+	/*
+	 * handle unaligned start bytes
+	 */
+	if ((l = addr - wp) != 0) {
+		data = 0;
+		for (i = 0, cp = wp; i < l; ++i, ++cp) {
+			data = (data >> 8) | (*(uchar *) cp << 8);
+		}
+		for (; i < 2 && cnt > 0; ++i) {
+			data = (data >> 8) | (*src++ << 8);
+			--cnt;
+			++cp;
+		}
+		for (; cnt == 0 && i < 2; ++i, ++cp) {
+			data = (data >> 8) | (*(uchar *) cp << 8);
+		}
 
-      if ((rc = write_word(info, wp, data)) != 0) {
-	 return (rc);
-      }
-      wp += 2;
-   }
+		if ((rc = write_word (info, wp, data)) != 0) {
+			return (rc);
+		}
+		wp += 2;
+	}
 
-   /*
-    * handle word aligned part
-    */
-   while (cnt >= 2) {
-      data = *((vu_short*)src);
-      if ((rc = write_word(info, wp, data)) != 0) {
-	  return (rc);
-      }
-      src += 2;
-      wp  += 2;
-      cnt -= 2;
-   }
+	/*
+	 * handle word aligned part
+	 */
+	while (cnt >= 2) {
+		data = *((vu_short *) src);
+		if ((rc = write_word (info, wp, data)) != 0) {
+			return (rc);
+		}
+		src += 2;
+		wp += 2;
+		cnt -= 2;
+	}
 
-   if (cnt == 0) {
-      return ERR_OK;
-   }
+	if (cnt == 0) {
+		return ERR_OK;
+	}
 
-   /*
-    * handle unaligned tail bytes
-    */
-   data = 0;
-   for (i=0, cp=wp; i<2 && cnt>0; ++i, ++cp) {
-      data = (data >> 8) | (*src++ << 8);
-      --cnt;
-   }
-   for (; i<2; ++i, ++cp) {
-      data = (data >> 8) | (*(uchar *)cp << 8);
-   }
+	/*
+	 * handle unaligned tail bytes
+	 */
+	data = 0;
+	for (i = 0, cp = wp; i < 2 && cnt > 0; ++i, ++cp) {
+		data = (data >> 8) | (*src++ << 8);
+		--cnt;
+	}
+	for (; i < 2; ++i, ++cp) {
+		data = (data >> 8) | (*(uchar *) cp << 8);
+	}
 
-   return write_word(info, wp, data);
+	return write_word (info, wp, data);
 }

board/csb226/csb226.c

@@ -71,7 +71,7 @@ int board_init (void)
 	/* so we do _nothing_ here */
 
 	/* arch number of CSB226 board */
-	gd->bd->bi_arch_number = 216;
+	gd->bd->bi_arch_number = MACH_TYPE_CSB226;
 
 	/* adress of boot parameters */
 	gd->bd->bi_boot_params = 0xa0000100;

board/dave/B2/B2.c

@@ -109,7 +109,7 @@ int board_init (void)
     PDATF = temp;
 
 	/* arch number MACH_TYPE_MBA44B0 */
-	gd->bd->bi_arch_number = 178;
+	gd->bd->bi_arch_number = MACH_TYPE_S3C44B0;
 
 	/* location of boot parameters */
 	gd->bd->bi_boot_params = 0x0c000100;

board/dbau1x00/README

@@ -1,30 +1,40 @@
-By Thomas.Lange@corelatus.se 2003-10-06
+By Thomas.Lange@corelatus.se 2004-Oct-05
 ----------------------------------------
-DbAu1000 is a development board from AMD containing
-an Alchemy AU1000 with mips32 core.
+DbAu1xx0 are development boards from AMD containing
+an Alchemy AU1xx0 series cpu with mips32 core.
+Existing cpu:s are Au1000, Au1100, Au1500 and Au1550
 
 Limitations & comments
 ----------------------
-I assume that you set board to BIG endian!
-Little endian not tested, most probably broken.
+Support was originally big endian only.
+I have not tested, but several u-boot users report working
+configurations in little endian mode.
 
 I named the board dbau1x00, to allow
 support for all three development boards
-some day ( dbau1000, dbau1100 and dbau1500 ).
+( dbau1000, dbau1100 and dbau1500 ).
+Now there is a new board called dbau1550 also, which
+should be supported RSN.
 
-I only have a dbau1000, so all testing is limited
-to this board!
+I only have a dbau1000, so my testing is limited
+to this board.
 
 The board has two different flash banks, that can
 be selected via dip switch. This makes it possible
 to test new bootloaders without thrashing the YAMON
-boot loader deliviered with board.
+boot loader delivered with board.
+
+NOTE! When you switch between the two boot flashes, the
+base addresses will be swapped.
+Have this in mind when you compile u-boot. TEXT_BASE has
+to match the address where u-boot is located when you
+actually launch.
 
 Ethernet only supported for mac0.
 
-Pcmcia only supported for slot 0, only 3.3V.
+PCMCIA only supported for slot 0, only 3.3V.
 
-Pcmcia IDE tested with Sandisk Compact Flash and
+PCMCIA IDE tested with Sandisk Compact Flash and
 IBM microdrive.
 
 ###################################
@@ -32,7 +42,7 @@ IBM microdrive.
 ###################################
 If you partition a disk on another system (e.g. laptop),
 all bytes will be swapped on 16bit level when using
-PCMCIA!!!!
+PCMCIA and running cpu in big endian mode!!!!
 
 This is probably due to an error in Au1000 chip.
 

board/dnp1110/dnp1110.c

@@ -39,7 +39,7 @@ int board_init (void)
 	/* so we do _nothing_ here */
 
 	/* arch number of DNP1110-Board */
-	gd->bd->bi_arch_number = 255;
+	gd->bd->bi_arch_number = MACH_TYPE_DNP1110;
 
     /* flash vpp on */
     PPDR |= 0x80;	/* assumes LCD controller is off */

board/ep7312/ep7312.c

@@ -40,7 +40,7 @@ int board_init (void)
 	IO_LEDFLSH = 0x40;
 
 	/* arch number MACH_TYPE_EDB7312 */
-	gd->bd->bi_arch_number = 131;
+	gd->bd->bi_arch_number = MACH_TYPE_EDB7312;
 
 	/* location of boot parameters */
 	gd->bd->bi_boot_params = 0xc0020100;

board/esd/ar405/Makefile

@@ -25,7 +25,7 @@ include $(TOPDIR)/config.mk
 
 LIB	= lib$(BOARD).a
 
-OBJS	= $(BOARD).o flash.o
+OBJS	= $(BOARD).o flash.o ../common/misc.o
 
 $(LIB):	$(OBJS) $(SOBJS)
 	$(AR) crv $@ $(OBJS)

board/esd/ar405/ar405.c

@@ -1,5 +1,5 @@
 /*
- * (C) Copyright 2001
+ * (C) Copyright 2001-2004
  * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
  *
  * See file CREDITS for list of people who contributed to this
@@ -28,6 +28,7 @@
 
 /*cmd_boot.c*/
 extern int do_reset (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]);
+extern void lxt971_no_sleep(void);
 
 /* ------------------------------------------------------------------------- */
 
@@ -40,6 +41,10 @@ const unsigned char fpgadata[] = {
 #include "fpgadata.c"
 };
 
+const unsigned char fpgadata_xl30[] = {
+#include "fpgadata_xl30.c"
+};
+
 /*
  * include common fpga code (for esd boards)
  */
@@ -64,45 +69,52 @@ int board_early_init_f (void)
 	/*
 	 * Boot onboard FPGA
 	 */
+	/* first try 40er image */
+	gd->board_type = 40;
 	status = fpga_boot ((unsigned char *) fpgadata, sizeof (fpgadata));
 	if (status != 0) {
-		/* booting FPGA failed */
+		/* try xl30er image */
+		gd->board_type = 30;
+		status = fpga_boot ((unsigned char *) fpgadata_xl30, sizeof (fpgadata_xl30));
+		if (status != 0) {
+			/* booting FPGA failed */
 #ifndef FPGA_DEBUG
-		/* set up serial port with default baudrate */
-		(void) get_clocks ();
-		gd->baudrate = CONFIG_BAUDRATE;
-		serial_init ();
-		console_init_f ();
+			/* set up serial port with default baudrate */
+			(void) get_clocks ();
+			gd->baudrate = CONFIG_BAUDRATE;
+			serial_init ();
+			console_init_f ();
 #endif
-		printf ("\nFPGA: Booting failed ");
-		switch (status) {
-		case ERROR_FPGA_PRG_INIT_LOW:
-			printf ("(Timeout: INIT not low after asserting PROGRAM*)\n ");
-			break;
-		case ERROR_FPGA_PRG_INIT_HIGH:
-			printf ("(Timeout: INIT not high after deasserting PROGRAM*)\n ");
-			break;
-		case ERROR_FPGA_PRG_DONE:
-			printf ("(Timeout: DONE not high after programming FPGA)\n ");
-			break;
-		}
+			printf ("\nFPGA: Booting failed ");
+			switch (status) {
+			case ERROR_FPGA_PRG_INIT_LOW:
+				printf ("(Timeout: INIT not low after asserting PROGRAM*)\n ");
+				break;
+			case ERROR_FPGA_PRG_INIT_HIGH:
+				printf ("(Timeout: INIT not high after deasserting PROGRAM*)\n ");
+				break;
+			case ERROR_FPGA_PRG_DONE:
+				printf ("(Timeout: DONE not high after programming FPGA)\n ");
+				break;
+			}
 
-		/* display infos on fpgaimage */
-		index = 15;
-		for (i = 0; i < 4; i++) {
-			len = fpgadata[index];
-			printf ("FPGA: %s\n", &(fpgadata[index + 1]));
-			index += len + 3;
+			/* display infos on fpgaimage */
+			index = 15;
+			for (i = 0; i < 4; i++) {
+				len = fpgadata[index];
+				printf ("FPGA: %s\n", &(fpgadata[index + 1]));
+				index += len + 3;
+			}
+			putc ('\n');
+			/* delayed reboot */
+			for (i = 20; i > 0; i--) {
+				printf ("Rebooting in %2d seconds \r", i);
+				for (index = 0; index < 1000; index++)
+					udelay (1000);
+			}
+			putc ('\n');
+			do_reset (NULL, 0, 0, NULL);
 		}
-		putc ('\n');
-		/* delayed reboot */
-		for (i = 20; i > 0; i--) {
-			printf ("Rebooting in %2d seconds \r", i);
-			for (index = 0; index < 1000; index++)
-				udelay (1000);
-		}
-		putc ('\n');
-		do_reset (NULL, 0, 0, NULL);
 	}
 
 	/*
@@ -139,32 +151,44 @@ int board_early_init_f (void)
 
 int checkboard (void)
 {
+	DECLARE_GLOBAL_DATA_PTR;
+
 	int index;
 	int len;
 	unsigned char str[64];
 	int i = getenv_r ("serial#", str, sizeof (str));
+	const unsigned char *fpga;
 
 	puts ("Board: ");
 
-	if (!i || strncmp (str, "AR405", 5)) {
-		puts ("### No HW ID - assuming AR405\n");
-		return (0);
+	if (i == -1) {
+		puts ("### No HW ID - assuming AR405");
+	} else {
+		puts(str);
 	}
 
-	puts (str);
-
 	puts ("\nFPGA:  ");
 
 	/* display infos on fpgaimage */
+	if (gd->board_type == 30) {
+		fpga = fpgadata_xl30;
+	} else {
+		fpga = fpgadata;
+	}
 	index = 15;
 	for (i = 0; i < 4; i++) {
-		len = fpgadata[index];
-		printf ("%s ", &(fpgadata[index + 1]));
+		len = fpga[index];
+		printf ("%s ", &(fpga[index + 1]));
 		index += len + 3;
 	}
 
 	putc ('\n');
 
+	/*
+	 * Disable sleep mode in LXT971
+	 */
+	lxt971_no_sleep();
+
 	return 0;
 }
 

board/esd/ar405/config.mk

@@ -26,4 +26,5 @@
 #
 
 #TEXT_BASE = 0xFFFE0000
-TEXT_BASE = 0xFFFD0000
+#TEXT_BASE = 0xFFFD0000
+TEXT_BASE = 0xFFFC0000

board/esd/ar405/flash.c

@@ -33,18 +33,19 @@
 /*-----------------------------------------------------------------------
  * Functions
  */
-static ulong flash_get_size (vu_long *addr, flash_info_t *info);
-static void flash_get_offsets (ulong base, flash_info_t *info);
+static ulong flash_get_size (vu_long * addr, flash_info_t * info);
+static void flash_get_offsets (ulong base, flash_info_t * info);
 
 /*-----------------------------------------------------------------------
  */
 
 unsigned long flash_init (void)
 {
-	unsigned long size_b0, size_b1;
+	unsigned long size_b0;
 	int i;
 	uint pbcr;
-	unsigned long base_b0, base_b1;
+	unsigned long base_b0;
+	int size_val = 0;
 
 	/* Init: no FLASHes known */
 	for (i=0; i<CFG_MAX_FLASH_BANKS; ++i) {
@@ -53,74 +54,48 @@ unsigned long flash_init (void)
 
 	/* Static FLASH Bank configuration here - FIXME XXX */
 
-	base_b0 = FLASH_BASE0_PRELIM;
-	size_b0 = flash_get_size((vu_long *)base_b0, &flash_info[0]);
+	size_b0 = flash_get_size((vu_long *)FLASH_BASE0_PRELIM, &flash_info[0]);
 
 	if (flash_info[0].flash_id == FLASH_UNKNOWN) {
 		printf ("## Unknown FLASH on Bank 0 - Size = 0x%08lx = %ld MB\n",
 			size_b0, size_b0<<20);
 	}
 
-	base_b1 = FLASH_BASE1_PRELIM;
-	size_b1 = flash_get_size((vu_long *)base_b1, &flash_info[1]);
+	/* Setup offsets */
+	flash_get_offsets (-size_b0, &flash_info[0]);
 
 	/* Re-do sizing to get full correct info */
+	mtdcr(ebccfga, pb0cr);
+	pbcr = mfdcr(ebccfgd);
+	mtdcr(ebccfga, pb0cr);
+	base_b0 = -size_b0;
+	switch (size_b0) {
+	case 1 << 20:
+		size_val = 0;
+		break;
+	case 2 << 20:
+		size_val = 1;
+		break;
+	case 4 << 20:
+		size_val = 2;
+		break;
+	case 8 << 20:
+		size_val = 3;
+		break;
+	case 16 << 20:
+		size_val = 4;
+		break;
+	}
+	pbcr = (pbcr & 0x0001ffff) | base_b0 | (size_val << 17);
+	mtdcr(ebccfgd, pbcr);
 
-	if (size_b1)
-	  {
-	    mtdcr(ebccfga, pb0cr);
-	    pbcr = mfdcr(ebccfgd);
-	    mtdcr(ebccfga, pb0cr);
-	    base_b1 = -size_b1;
-	    pbcr = (pbcr & 0x0001ffff) | base_b1 | (((size_b1/1024/1024)-1)<<17);
-	    mtdcr(ebccfgd, pbcr);
-	    /*          printf("pb1cr = %x\n", pbcr); */
-	  }
-
-	if (size_b0)
-	  {
-	    mtdcr(ebccfga, pb1cr);
-	    pbcr = mfdcr(ebccfgd);
-	    mtdcr(ebccfga, pb1cr);
-	    base_b0 = base_b1 - size_b0;
-	    pbcr = (pbcr & 0x0001ffff) | base_b0 | (((size_b0/1024/1024)-1)<<17);
-	    mtdcr(ebccfgd, pbcr);
-	    /*            printf("pb0cr = %x\n", pbcr); */
-	  }
-
-	size_b0 = flash_get_size((vu_long *)base_b0, &flash_info[0]);
-
-	flash_get_offsets (base_b0, &flash_info[0]);
-
-	/* monitor protection ON by default */
+	/* Monitor protection ON by default */
 	(void)flash_protect(FLAG_PROTECT_SET,
-			    base_b0+size_b0-monitor_flash_len,
-			    base_b0+size_b0-1,
+			    -CFG_MONITOR_LEN,
+			    0xffffffff,
 			    &flash_info[0]);
 
-	if (size_b1) {
-		/* Re-do sizing to get full correct info */
-		size_b1 = flash_get_size((vu_long *)base_b1, &flash_info[1]);
-
-		flash_get_offsets (base_b1, &flash_info[1]);
-
-		/* monitor protection ON by default */
-		(void)flash_protect(FLAG_PROTECT_SET,
-				    base_b1+size_b1-monitor_flash_len,
-				    base_b1+size_b1-1,
-				    &flash_info[1]);
-		/* monitor protection OFF by default (one is enough) */
-		(void)flash_protect(FLAG_PROTECT_CLEAR,
-				    base_b0+size_b0-monitor_flash_len,
-				    base_b0+size_b0-1,
-				    &flash_info[0]);
-	} else {
-		flash_info[1].flash_id = FLASH_UNKNOWN;
-		flash_info[1].sector_count = -1;
-	}
-
 	flash_info[0].size = size_b0;
-	flash_info[1].size = size_b1;
 
-	return (size_b0 + size_b1);
+	return (size_b0);
 }

board/esd/common/misc.c

@@ -0,0 +1,40 @@
+/*
+ * (C) Copyright 2004
+ * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+
+#ifdef CONFIG_LXT971_NO_SLEEP
+#include <miiphy.h>
+#endif
+
+
+#ifdef CONFIG_LXT971_NO_SLEEP
+void lxt971_no_sleep(void)
+{
+	unsigned short reg;
+
+	miiphy_read(CONFIG_PHY_ADDR, 0x10, &reg);
+	reg &= ~0x0040;                  /* disable sleep mode */
+	miiphy_write(CONFIG_PHY_ADDR, 0x10, reg);
+}
+#endif /* CONFIG_LXT971_NO_SLEEP */

board/gcplus/gcplus.c

@@ -37,7 +37,7 @@ board_init(void)
 {
 	DECLARE_GLOBAL_DATA_PTR;
 
-	gd->bd->bi_arch_number = 29;	/* ADS GraphicsClientPlus Board */
+	gd->bd->bi_arch_number = MACH_TYPE_GRAPHICSCLIENT;
 
 	gd->bd->bi_boot_params = 0xc000003c; /* Weird address? */
 

board/icecube/icecube.c

@@ -288,6 +288,8 @@ void init_ide_reset (void)
     	/* Configure PSC1_4 as GPIO output for ATA reset */
 	*(vu_long *) MPC5XXX_WU_GPIO_ENABLE |= GPIO_PSC1_4;
 	*(vu_long *) MPC5XXX_WU_GPIO_DIR    |= GPIO_PSC1_4;
+	/* Deassert reset */
+	*(vu_long *) MPC5XXX_WU_GPIO_DATA   |= GPIO_PSC1_4;
 }
 
 void ide_set_reset (int idereset)
@@ -296,6 +298,8 @@ void ide_set_reset (int idereset)
 
 	if (idereset) {
 		*(vu_long *) MPC5XXX_WU_GPIO_DATA &= ~GPIO_PSC1_4;
+		/* Make a delay. MPC5200 spec says 25 usec min */
+		udelay(500000);
 	} else {
 		*(vu_long *) MPC5XXX_WU_GPIO_DATA |=  GPIO_PSC1_4;
 	}

board/impa7/impa7.c

@@ -40,7 +40,7 @@ int board_init (void)
 	IO_LEDFLSH = 0x40;
 
 	/* arch number of EP7111 */
-	gd->bd->bi_arch_number = 50;
+	gd->bd->bi_arch_number = MACH_TYPE_EDB7211;
 
 	/* location of boot parameters for EP7111 */
 	gd->bd->bi_boot_params = 0xc0020100;

board/integratorap/integratorap.c

@@ -68,7 +68,7 @@ int board_init (void)
 	DECLARE_GLOBAL_DATA_PTR;
 
 	/* arch number of Integrator Board */
-	gd->bd->bi_arch_number = 21;
+	gd->bd->bi_arch_number = MACH_TYPE_INTEGRATOR;
 
 	/* adress of boot parameters */
 	gd->bd->bi_boot_params = 0x00000100;

board/integratorcp/integratorcp.c

@@ -64,7 +64,7 @@ int board_init (void)
 	DECLARE_GLOBAL_DATA_PTR;
 
 	/* arch number of Integrator Board */
-	gd->bd->bi_arch_number = 275;
+	gd->bd->bi_arch_number = MACH_TYPE_CINTEGRATOR;
 
 	/* adress of boot parameters */
 	gd->bd->bi_boot_params = 0x00000100;

board/ixdp425/ixdp425.c

@@ -54,7 +54,7 @@ board_init (void)
 	DECLARE_GLOBAL_DATA_PTR;
 
 	/* arch number of IXDP */
-	gd->bd->bi_arch_number = 245;
+	gd->bd->bi_arch_number = MACH_TYPE_IXDP425;
 
 	/* adress of boot parameters */
 	gd->bd->bi_boot_params = 0x00000100;

board/jse/host_bridge.c

@@ -40,9 +40,12 @@ void host_bridge_init (void)
 	pci_dev_t dev = PCI_BDF (0, 10, 0);
 
 	int rc;
-	u32 val32;
 
-	rc = pci_read_config_dword (dev, 0, &val32);
+	/* Set PCI Class code --
+	   The primary side sees this class code at 0x08 in the
+	   primary config space. This must be something other then a
+	   bridge, or MS Windows starts doing weird stuff to me. */
+	pci_write_config_dword (dev, 0x48, 0x04800000);
 
 	/* Set subsystem ID --
 	   The primary side sees this value at 0x2c. We set it here so

board/lart/lart.c

@@ -39,7 +39,7 @@ int board_init (void)
 	/* so we do _nothing_ here */
 
 	/* arch number of LART-Board */
-	gd->bd->bi_arch_number = 27;
+	gd->bd->bi_arch_number = MACH_TYPE_LART;
 
 	/* adress of boot parameters */
 	gd->bd->bi_boot_params = 0xc0000100;

board/lubbock/lubbock.c

@@ -42,7 +42,7 @@ int board_init (void)
 	/* so we do _nothing_ here */
 
 	/* arch number of Lubbock-Board */
-	gd->bd->bi_arch_number = 89;
+	gd->bd->bi_arch_number = MACH_TYPE_LUBBOCK;
 
 	/* adress of boot parameters */
 	gd->bd->bi_boot_params = 0xa0000100;

board/mpc8540ads/Makefile

@@ -25,7 +25,7 @@ include $(TOPDIR)/config.mk
 
 LIB	= lib$(BOARD).a
 
-OBJS	:= $(BOARD).o flash.o
+OBJS	:= $(BOARD).o
 SOBJS	:= init.o
 #SOBJS	:=
 

board/mpc8540ads/flash.c

@@ -1,537 +0,0 @@
-/*
- * (C) Copyright 2003 Motorola Inc.
- *  Xianghua Xiao,(X.Xiao@motorola.com)
- *
- * (C) Copyright 2000, 2001
- *  Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2001, Stuart Hughes, Lineo Inc, stuarth@lineo.com
- * Add support the Sharp chips on the mpc8260ads.
- * I started with board/ip860/flash.c and made changes I found in
- * the MTD project by David Schleef.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-
-#if !defined(CFG_NO_FLASH)
-
-flash_info_t	flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips	*/
-
-#if defined(CFG_ENV_IS_IN_FLASH)
-# ifndef  CFG_ENV_ADDR
-#  define CFG_ENV_ADDR	(CFG_FLASH_BASE + CFG_ENV_OFFSET)
-# endif
-# ifndef  CFG_ENV_SIZE
-#  define CFG_ENV_SIZE	CFG_ENV_SECT_SIZE
-# endif
-# ifndef  CFG_ENV_SECT_SIZE
-#  define CFG_ENV_SECT_SIZE  CFG_ENV_SIZE
-# endif
-#endif
-
-#undef DEBUG
-
-/*-----------------------------------------------------------------------
- * Functions
- */
-static ulong flash_get_size (vu_long *addr, flash_info_t *info);
-static int write_word (flash_info_t *info, ulong dest, ulong data);
-static int clear_block_lock_bit(vu_long * addr);
-/*-----------------------------------------------------------------------
- */
-
-unsigned long flash_init (void)
-{
-	unsigned long size;
-	int i;
-
-	/* Init: enable write,
-	 * or we cannot even write flash commands
-	 */
-	for (i=0; i<CFG_MAX_FLASH_BANKS; ++i) {
-		flash_info[i].flash_id = FLASH_UNKNOWN;
-
-		/* set the default sector offset */
-	}
-
-	/* Static FLASH Bank configuration here - FIXME XXX */
-
-	size = flash_get_size((vu_long *)CFG_FLASH_BASE, &flash_info[0]);
-
-	if (flash_info[0].flash_id == FLASH_UNKNOWN) {
-		printf ("## Unknown FLASH on Bank 0 - Size = 0x%08lx = %ld MB\n",
-			size, size<<20);
-	}
-
-	/* Re-do sizing to get full correct info */
-	size = flash_get_size((vu_long *)CFG_FLASH_BASE, &flash_info[0]);
-
-	flash_info[0].size = size;
-
-#if CFG_MONITOR_BASE >= CFG_FLASH_BASE
-	/* monitor protection ON by default */
-	flash_protect(FLAG_PROTECT_SET,
-		      CFG_MONITOR_BASE,
-		      CFG_MONITOR_BASE+monitor_flash_len-1,
-		      &flash_info[0]);
-
-#ifdef	CFG_ENV_IS_IN_FLASH
-	/* ENV protection ON by default */
-	flash_protect(FLAG_PROTECT_SET,
-		      CFG_ENV_ADDR,
-		      CFG_ENV_ADDR+CFG_ENV_SECT_SIZE-1,
-		      &flash_info[0]);
-#endif
-#endif
-	return (size);
-}
-
-/*-----------------------------------------------------------------------
- */
-void flash_print_info  (flash_info_t *info)
-{
-	int i;
-
-	if (info->flash_id == FLASH_UNKNOWN) {
-		printf ("missing or unknown FLASH type\n");
-		return;
-	}
-
-	switch (info->flash_id & FLASH_VENDMASK) {
-	case FLASH_MAN_INTEL:	printf ("Intel ");		break;
-	case FLASH_MAN_SHARP:   printf ("Sharp ");		break;
-	default:		printf ("Unknown Vendor ");	break;
-	}
-
-	switch (info->flash_id & FLASH_TYPEMASK) {
-	case FLASH_28F016SV:	printf ("28F016SV (16 Mbit, 32 x 64k)\n");
-				break;
-	case FLASH_28F160S3:	printf ("28F160S3 (16 Mbit, 32 x 512K)\n");
-				break;
-	case FLASH_28F320S3:	printf ("28F320S3 (32 Mbit, 64 x 512K)\n");
-				break;
-	case FLASH_LH28F016SCT: printf ("28F016SC (16 Mbit, 32 x 64K)\n");
-				break;
-	case FLASH_28F640J3A:   printf ("28F640J3A (64 Mbit, 64 x 128K)\n");
-				break;
-	default:		printf ("Unknown Chip Type\n");
-				break;
-	}
-
-	printf ("  Size: %ld MB in %d Sectors\n",
-		info->size >> 20, info->sector_count);
-
-	printf ("  Sector Start Addresses:");
-	for (i=0; i<info->sector_count; ++i) {
-		if ((i % 5) == 0)
-			printf ("\n   ");
-		printf (" %08lX%s",
-			info->start[i],
-			info->protect[i] ? " (RO)" : "     "
-		);
-	}
-	printf ("\n");
-}
-
-/*
- * The following code cannot be run from FLASH!
- */
-
-static ulong flash_get_size (vu_long *addr, flash_info_t *info)
-{
-	short i;
-	ulong value;
-	ulong base = (ulong)addr;
-	ulong sector_offset;
-
-#ifdef DEBUG
-	printf("Check flash at 0x%08x\n",(uint)addr);
-#endif
-	/* Write "Intelligent Identifier" command: read Manufacturer ID */
-	*addr = 0x90909090;
-	udelay(20);
-	asm("sync");
-
-	value = addr[0] & 0x00FF00FF;
-
-#ifdef DEBUG
-	printf("manufacturer=0x%x\n",(uint)value);
-#endif
-	switch (value) {
-	case MT_MANUFACT:	/* SHARP, MT or => Intel */
-	case INTEL_ALT_MANU:
-		info->flash_id = FLASH_MAN_INTEL;
-		break;
-	default:
-		printf("unknown manufacturer: %x\n", (unsigned int)value);
-		info->flash_id = FLASH_UNKNOWN;
-		info->sector_count = 0;
-		info->size = 0;
-		return (0);			/* no or unknown flash	*/
-	}
-
-	value = addr[1] & 0x00FF00FF;             /* device ID            */
-
-#ifdef DEBUG
-	printf("deviceID=0x%x\n",(uint)value);
-#endif
-	switch (value) {
-	case (INTEL_ID_28F016S):
-		info->flash_id += FLASH_28F016SV;
-		info->sector_count = 32;
-		info->size = 0x00400000;
-		sector_offset = 0x20000;
-		break;				/* => 2x2 MB		*/
-
-	case (INTEL_ID_28F160S3):
-		info->flash_id += FLASH_28F160S3;
-		info->sector_count = 32;
-		info->size = 0x00400000;
-		sector_offset = 0x20000;
-		break;				/* => 2x2 MB		*/
-
-	case (INTEL_ID_28F320S3):
-		info->flash_id += FLASH_28F320S3;
-		info->sector_count = 64;
-		info->size = 0x00800000;
-		sector_offset = 0x20000;
-		break;				/* => 2x4 MB		*/
-
-	case (INTEL_ID_28F640J3A):
-		info->flash_id += FLASH_28F640J3A;
-		info->sector_count = 64;
-		info->size = 0x01000000;
-		sector_offset = 0x40000;
-		break;                          /* => 2x8 MB             */
-
-	case SHARP_ID_28F016SCL:
-	case SHARP_ID_28F016SCZ:
-		info->flash_id      = FLASH_MAN_SHARP | FLASH_LH28F016SCT;
-		info->sector_count  = 32;
-		info->size          = 0x00800000;
-		sector_offset = 0x40000;
-		break;				/* => 4x2 MB		*/
-
-
-	default:
-		info->flash_id = FLASH_UNKNOWN;
-		return (0);			/* => no or unknown flash */
-
-	}
-
-	/* set up sector start address table */
-	for (i = 0; i < info->sector_count; i++) {
-		info->start[i] = base;
-		base += sector_offset;
-		/* don't know how to check sector protection */
-		info->protect[i] = 0;
-	}
-
-	/*
-	 * Prevent writes to uninitialized FLASH.
-	 */
-	if (info->flash_id != FLASH_UNKNOWN) {
-		addr = (vu_long *)info->start[0];
-		*addr = 0xFFFFFF;	/* reset bank to read array mode */
-		asm("sync");
-	}
-
-	return (info->size);
-}
-
-
-/*-----------------------------------------------------------------------
- */
-
-int	flash_erase (flash_info_t *info, int s_first, int s_last)
-{
-	int flag, prot, sect;
-	ulong start, now, last;
-
-	if ((s_first < 0) || (s_first > s_last)) {
-		if (info->flash_id == FLASH_UNKNOWN) {
-			printf ("- missing\n");
-		} else {
-			printf ("- no sectors to erase\n");
-		}
-		return 1;
-	}
-
-	if (    ((info->flash_id & FLASH_VENDMASK) != FLASH_MAN_INTEL)
-	     && ((info->flash_id & FLASH_VENDMASK) != FLASH_MAN_SHARP) ) {
-		printf ("Can't erase unknown flash type %08lx - aborted\n",
-			info->flash_id);
-		return 1;
-	}
-
-	prot = 0;
-	for (sect=s_first; sect<=s_last; ++sect) {
-		if (info->protect[sect]) {
-			prot++;
-		}
-	}
-
-	if (prot) {
-		printf ("- Warning: %d protected sectors will not be erased!\n",
-			prot);
-	} else {
-		printf ("\n");
-	}
-
-#ifdef DEBUG
-	printf("\nFlash Erase:\n");
-#endif
-	/* Make Sure Block Lock Bit is not set. */
-	if(clear_block_lock_bit((vu_long *)(info->start[s_first]))){
-		return 1;
-	}
-
-	/* Start erase on unprotected sectors */
-#if defined(DEBUG)
-	printf("Begin to erase now,s_first=0x%x s_last=0x%x...\n",s_first,s_last);
-#endif
-	for (sect = s_first; sect<=s_last; sect++) {
-		if (info->protect[sect] == 0) {	/* not protected */
-			vu_long *addr = (vu_long *)(info->start[sect]);
-			asm("sync");
-
-			last = start = get_timer (0);
-
-			/* Disable interrupts which might cause a timeout here */
-			flag = disable_interrupts();
-
-			/* Reset Array */
-			*addr = 0xffffffff;
-			asm("sync");
-			/* Clear Status Register */
-			*addr = 0x50505050;
-			asm("sync");
-			/* Single Block Erase Command */
-			*addr = 0x20202020;
-			asm("sync");
-			/* Confirm */
-			*addr = 0xD0D0D0D0;
-			asm("sync");
-
-			if((info->flash_id & FLASH_TYPEMASK) != FLASH_LH28F016SCT) {
-			    /* Resume Command, as per errata update */
-			    *addr = 0xD0D0D0D0;
-			    asm("sync");
-			}
-
-			/* re-enable interrupts if necessary */
-			if (flag)
-				enable_interrupts();
-
-			/* wait at least 80us - let's wait 1 ms */
-			udelay (1000);
-			while ((*addr & 0x00800080) != 0x00800080) {
-				if(*addr & 0x00200020){
-					printf("Error in Block Erase - Lock Bit may be set!\n");
-					printf("Status Register = 0x%X\n", (uint)*addr);
-					*addr = 0xFFFFFFFF;	/* reset bank */
-					asm("sync");
-					return 1;
-				}
-				if ((now=get_timer(start)) > CFG_FLASH_ERASE_TOUT) {
-					printf ("Timeout\n");
-					*addr = 0xFFFFFFFF;	/* reset bank */
-					asm("sync");
-					return 1;
-				}
-				/* show that we're waiting */
-				if ((now - last) > 1000) {	/* every second */
-					putc ('.');
-					last = now;
-				}
-			}
-
-			/* reset to read mode */
-			*addr = 0xFFFFFFFF;
-			asm("sync");
-		}
-	}
-
-	printf ("flash erase done\n");
-	return 0;
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-
-int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
-{
-	ulong cp, wp, data;
-	int i, l, rc;
-
-	wp = (addr & ~3);	/* get lower word aligned address */
-
-	/*
-	 * handle unaligned start bytes
-	 */
-	if ((l = addr - wp) != 0) {
-		data = 0;
-		for (i=0, cp=wp; i<l; ++i, ++cp) {
-			data = (data << 8) | (*(uchar *)cp);
-		}
-		for (; i<4 && cnt>0; ++i) {
-			data = (data << 8) | *src++;
-			--cnt;
-			++cp;
-		}
-		for (; cnt==0 && i<4; ++i, ++cp) {
-			data = (data << 8) | (*(uchar *)cp);
-		}
-
-		if ((rc = write_word(info, wp, data)) != 0) {
-			return (rc);
-		}
-		wp += 4;
-	}
-
-	/*
-	 * handle word aligned part
-	 */
-	while (cnt >= 4) {
-		data = 0;
-		for (i=0; i<4; ++i) {
-			data = (data << 8) | *src++;
-		}
-		if ((rc = write_word(info, wp, data)) != 0) {
-			return (rc);
-		}
-		wp  += 4;
-		cnt -= 4;
-	}
-
-	if (cnt == 0) {
-		return (0);
-	}
-
-	/*
-	 * handle unaligned tail bytes
-	 */
-	data = 0;
-	for (i=0, cp=wp; i<4 && cnt>0; ++i, ++cp) {
-		data = (data << 8) | *src++;
-		--cnt;
-	}
-	for (; i<4; ++i, ++cp) {
-		data = (data << 8) | (*(uchar *)cp);
-	}
-
-	return (write_word(info, wp, data));
-}
-
-/*-----------------------------------------------------------------------
- * Write a word to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_word (flash_info_t *info, ulong dest, ulong data)
-{
-	vu_long *addr = (vu_long *)dest;
-	ulong start, csr;
-	int flag;
-
-	/* Check if Flash is (sufficiently) erased */
-	if ((*addr & data) != data) {
-		return (2);
-	}
-	/* Disable interrupts which might cause a timeout here */
-	flag = disable_interrupts();
-
-	/* Write Command */
-	*addr = 0x10101010;
-	asm("sync");
-
-	/* Write Data */
-	*addr = data;
-
-	/* re-enable interrupts if necessary */
-	if (flag)
-		enable_interrupts();
-
-	/* data polling for D7 */
-	start = get_timer (0);
-	flag  = 0;
-
-	while (((csr = *addr) & 0x00800080) != 0x00800080) {
-		if (get_timer(start) > CFG_FLASH_WRITE_TOUT) {
-			flag = 1;
-			break;
-		}
-	}
-	if (csr & 0x40404040) {
-		printf ("CSR indicates write error (%08lx) at %08lx\n", csr, (ulong)addr);
-		flag = 1;
-	}
-
-	/* Clear Status Registers Command */
-	*addr = 0x50505050;
-	asm("sync");
-	/* Reset to read array mode */
-	*addr = 0xFFFFFFFF;
-	asm("sync");
-
-	return (flag);
-}
-
-/*-----------------------------------------------------------------------
- * Clear Block Lock Bit, returns:
- * 0 - OK
- * 1 - Timeout
- */
-
-static int clear_block_lock_bit(vu_long  * addr)
-{
-	ulong start, now;
-
-	/* Reset Array */
-	*addr = 0xffffffff;
-	asm("sync");
-	/* Clear Status Register */
-	*addr = 0x50505050;
-	asm("sync");
-
-	*addr = 0x60606060;
-	asm("sync");
-	*addr = 0xd0d0d0d0;
-	asm("sync");
-
-	start = get_timer (0);
-	while((*addr & 0x00800080) != 0x00800080){
-		if ((now=get_timer(start)) > CFG_FLASH_ERASE_TOUT) {
-			printf ("Timeout on clearing Block Lock Bit\n");
-			*addr = 0xFFFFFFFF;	/* reset bank */
-			asm("sync");
-			return 1;
-		}
-	}
-	return 0;
-}
-
-#endif /* !CFG_NO_FLASH */

board/mpc8540ads/mpc8540ads.c

@@ -44,13 +44,6 @@ long int fixed_sdram(void);
 
 int board_early_init_f (void)
 {
-#if defined(CONFIG_PCI)
-    volatile immap_t *immr = (immap_t *)CFG_IMMR;
-    volatile ccsr_pcix_t *pci = &immr->im_pcix;
-
-    pci->peer &= 0xffffffdf; /* disable master abort */
-#endif
-
     return 0;
 }
 

board/mpc8560ads/Makefile

@@ -25,7 +25,7 @@ include $(TOPDIR)/config.mk
 
 LIB	= lib$(BOARD).a
 
-OBJS	:= $(BOARD).o flash.o
+OBJS	:= $(BOARD).o
 SOBJS	:= init.o
 #SOBJS	:=
 

board/mpc8560ads/flash.c

@@ -1,537 +0,0 @@
-/*
- * (C) Copyright 2003 Motorola Inc.
- *  Xianghua Xiao,(X.Xiao@motorola.com)
- *
- * (C) Copyright 2000, 2001
- *  Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2001, Stuart Hughes, Lineo Inc, stuarth@lineo.com
- * Add support the Sharp chips on the mpc8260ads.
- * I started with board/ip860/flash.c and made changes I found in
- * the MTD project by David Schleef.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-
-#if !defined(CFG_NO_FLASH)
-
-flash_info_t	flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips	*/
-
-#if defined(CFG_ENV_IS_IN_FLASH)
-# ifndef  CFG_ENV_ADDR
-#  define CFG_ENV_ADDR	(CFG_FLASH_BASE + CFG_ENV_OFFSET)
-# endif
-# ifndef  CFG_ENV_SIZE
-#  define CFG_ENV_SIZE	CFG_ENV_SECT_SIZE
-# endif
-# ifndef  CFG_ENV_SECT_SIZE
-#  define CFG_ENV_SECT_SIZE  CFG_ENV_SIZE
-# endif
-#endif
-
-#undef DEBUG
-
-/*-----------------------------------------------------------------------
- * Functions
- */
-static ulong flash_get_size (vu_long *addr, flash_info_t *info);
-static int write_word (flash_info_t *info, ulong dest, ulong data);
-static int clear_block_lock_bit(vu_long * addr);
-/*-----------------------------------------------------------------------
- */
-
-unsigned long flash_init (void)
-{
-	unsigned long size;
-	int i;
-
-	/* Init: enable write,
-	 * or we cannot even write flash commands
-	 */
-	for (i=0; i<CFG_MAX_FLASH_BANKS; ++i) {
-		flash_info[i].flash_id = FLASH_UNKNOWN;
-
-		/* set the default sector offset */
-	}
-
-	/* Static FLASH Bank configuration here - FIXME XXX */
-
-	size = flash_get_size((vu_long *)CFG_FLASH_BASE, &flash_info[0]);
-
-	if (flash_info[0].flash_id == FLASH_UNKNOWN) {
-		printf ("## Unknown FLASH on Bank 0 - Size = 0x%08lx = %ld MB\n",
-			size, size<<20);
-	}
-
-	/* Re-do sizing to get full correct info */
-	size = flash_get_size((vu_long *)CFG_FLASH_BASE, &flash_info[0]);
-
-	flash_info[0].size = size;
-
-#if CFG_MONITOR_BASE >= CFG_FLASH_BASE
-	/* monitor protection ON by default */
-	flash_protect(FLAG_PROTECT_SET,
-		      CFG_MONITOR_BASE,
-		      CFG_MONITOR_BASE+monitor_flash_len-1,
-		      &flash_info[0]);
-
-#ifdef	CFG_ENV_IS_IN_FLASH
-	/* ENV protection ON by default */
-	flash_protect(FLAG_PROTECT_SET,
-		      CFG_ENV_ADDR,
-		      CFG_ENV_ADDR+CFG_ENV_SECT_SIZE-1,
-		      &flash_info[0]);
-#endif
-#endif
-	return (size);
-}
-
-/*-----------------------------------------------------------------------
- */
-void flash_print_info  (flash_info_t *info)
-{
-	int i;
-
-	if (info->flash_id == FLASH_UNKNOWN) {
-		printf ("missing or unknown FLASH type\n");
-		return;
-	}
-
-	switch (info->flash_id & FLASH_VENDMASK) {
-	case FLASH_MAN_INTEL:	printf ("Intel ");		break;
-	case FLASH_MAN_SHARP:   printf ("Sharp ");		break;
-	default:		printf ("Unknown Vendor ");	break;
-	}
-
-	switch (info->flash_id & FLASH_TYPEMASK) {
-	case FLASH_28F016SV:	printf ("28F016SV (16 Mbit, 32 x 64k)\n");
-				break;
-	case FLASH_28F160S3:	printf ("28F160S3 (16 Mbit, 32 x 512K)\n");
-				break;
-	case FLASH_28F320S3:	printf ("28F320S3 (32 Mbit, 64 x 512K)\n");
-				break;
-	case FLASH_LH28F016SCT: printf ("28F016SC (16 Mbit, 32 x 64K)\n");
-				break;
-	case FLASH_28F640J3A:   printf ("28F640J3A (64 Mbit, 64 x 128K)\n");
-				break;
-	default:		printf ("Unknown Chip Type\n");
-				break;
-	}
-
-	printf ("  Size: %ld MB in %d Sectors\n",
-		info->size >> 20, info->sector_count);
-
-	printf ("  Sector Start Addresses:");
-	for (i=0; i<info->sector_count; ++i) {
-		if ((i % 5) == 0)
-			printf ("\n   ");
-		printf (" %08lX%s",
-			info->start[i],
-			info->protect[i] ? " (RO)" : "     "
-		);
-	}
-	printf ("\n");
-}
-
-/*
- * The following code cannot be run from FLASH!
- */
-
-static ulong flash_get_size (vu_long *addr, flash_info_t *info)
-{
-	short i;
-	ulong value;
-	ulong base = (ulong)addr;
-	ulong sector_offset;
-
-#ifdef DEBUG
-	printf("Check flash at 0x%08x\n",(uint)addr);
-#endif
-	/* Write "Intelligent Identifier" command: read Manufacturer ID */
-	*addr = 0x90909090;
-	udelay(20);
-	asm("sync");
-
-	value = addr[0] & 0x00FF00FF;
-
-#ifdef DEBUG
-	printf("manufacturer=0x%x\n",(uint)value);
-#endif
-	switch (value) {
-	case MT_MANUFACT:	/* SHARP, MT or => Intel */
-	case INTEL_ALT_MANU:
-		info->flash_id = FLASH_MAN_INTEL;
-		break;
-	default:
-		printf("unknown manufacturer: %x\n", (unsigned int)value);
-		info->flash_id = FLASH_UNKNOWN;
-		info->sector_count = 0;
-		info->size = 0;
-		return (0);			/* no or unknown flash	*/
-	}
-
-	value = addr[1] & 0x00FF00FF;             /* device ID            */
-
-#ifdef DEBUG
-	printf("deviceID=0x%x\n",(uint)value);
-#endif
-	switch (value) {
-	case (INTEL_ID_28F016S):
-		info->flash_id += FLASH_28F016SV;
-		info->sector_count = 32;
-		info->size = 0x00400000;
-		sector_offset = 0x20000;
-		break;				/* => 2x2 MB		*/
-
-	case (INTEL_ID_28F160S3):
-		info->flash_id += FLASH_28F160S3;
-		info->sector_count = 32;
-		info->size = 0x00400000;
-		sector_offset = 0x20000;
-		break;				/* => 2x2 MB		*/
-
-	case (INTEL_ID_28F320S3):
-		info->flash_id += FLASH_28F320S3;
-		info->sector_count = 64;
-		info->size = 0x00800000;
-		sector_offset = 0x20000;
-		break;				/* => 2x4 MB		*/
-
-	case (INTEL_ID_28F640J3A):
-		info->flash_id += FLASH_28F640J3A;
-		info->sector_count = 64;
-		info->size = 0x01000000;
-		sector_offset = 0x40000;
-		break;                          /* => 8 MB             */
-
-	case SHARP_ID_28F016SCL:
-	case SHARP_ID_28F016SCZ:
-		info->flash_id      = FLASH_MAN_SHARP | FLASH_LH28F016SCT;
-		info->sector_count  = 32;
-		info->size          = 0x00800000;
-		sector_offset = 0x40000;
-		break;				/* => 4x2 MB		*/
-
-
-	default:
-		info->flash_id = FLASH_UNKNOWN;
-		return (0);			/* => no or unknown flash */
-
-	}
-
-	/* set up sector start address table */
-	for (i = 0; i < info->sector_count; i++) {
-		info->start[i] = base;
-		base += sector_offset;
-		/* don't know how to check sector protection */
-		info->protect[i] = 0;
-	}
-
-	/*
-	 * Prevent writes to uninitialized FLASH.
-	 */
-	if (info->flash_id != FLASH_UNKNOWN) {
-		addr = (vu_long *)info->start[0];
-		*addr = 0xFFFFFF;	/* reset bank to read array mode */
-		asm("sync");
-	}
-
-	return (info->size);
-}
-
-
-/*-----------------------------------------------------------------------
- */
-
-int	flash_erase (flash_info_t *info, int s_first, int s_last)
-{
-	int flag, prot, sect;
-	ulong start, now, last;
-
-	if ((s_first < 0) || (s_first > s_last)) {
-		if (info->flash_id == FLASH_UNKNOWN) {
-			printf ("- missing\n");
-		} else {
-			printf ("- no sectors to erase\n");
-		}
-		return 1;
-	}
-
-	if (    ((info->flash_id & FLASH_VENDMASK) != FLASH_MAN_INTEL)
-	     && ((info->flash_id & FLASH_VENDMASK) != FLASH_MAN_SHARP) ) {
-		printf ("Can't erase unknown flash type %08lx - aborted\n",
-			info->flash_id);
-		return 1;
-	}
-
-	prot = 0;
-	for (sect=s_first; sect<=s_last; ++sect) {
-		if (info->protect[sect]) {
-			prot++;
-		}
-	}
-
-	if (prot) {
-		printf ("- Warning: %d protected sectors will not be erased!\n",
-			prot);
-	} else {
-		printf ("\n");
-	}
-
-#ifdef DEBUG
-	printf("\nFlash Erase:\n");
-#endif
-	/* Make Sure Block Lock Bit is not set. */
-	if(clear_block_lock_bit((vu_long *)(info->start[s_first]))){
-		return 1;
-	}
-
-	/* Start erase on unprotected sectors */
-#if defined(DEBUG)
-	printf("Begin to erase now,s_first=0x%x s_last=0x%x...\n",s_first,s_last);
-#endif
-	for (sect = s_first; sect<=s_last; sect++) {
-		if (info->protect[sect] == 0) {	/* not protected */
-			vu_long *addr = (vu_long *)(info->start[sect]);
-			asm("sync");
-
-			last = start = get_timer (0);
-
-			/* Disable interrupts which might cause a timeout here */
-			flag = disable_interrupts();
-
-			/* Reset Array */
-			*addr = 0xffffffff;
-			asm("sync");
-			/* Clear Status Register */
-			*addr = 0x50505050;
-			asm("sync");
-			/* Single Block Erase Command */
-			*addr = 0x20202020;
-			asm("sync");
-			/* Confirm */
-			*addr = 0xD0D0D0D0;
-			asm("sync");
-
-			if((info->flash_id & FLASH_TYPEMASK) != FLASH_LH28F016SCT) {
-			    /* Resume Command, as per errata update */
-			    *addr = 0xD0D0D0D0;
-			    asm("sync");
-			}
-
-			/* re-enable interrupts if necessary */
-			if (flag)
-				enable_interrupts();
-
-			/* wait at least 80us - let's wait 1 ms */
-			udelay (1000);
-			while ((*addr & 0x00800080) != 0x00800080) {
-				if(*addr & 0x00200020){
-					printf("Error in Block Erase - Lock Bit may be set!\n");
-					printf("Status Register = 0x%X\n", (uint)*addr);
-					*addr = 0xFFFFFFFF;	/* reset bank */
-					asm("sync");
-					return 1;
-				}
-				if ((now=get_timer(start)) > CFG_FLASH_ERASE_TOUT) {
-					printf ("Timeout\n");
-					*addr = 0xFFFFFFFF;	/* reset bank */
-					asm("sync");
-					return 1;
-				}
-				/* show that we're waiting */
-				if ((now - last) > 1000) {	/* every second */
-					putc ('.');
-					last = now;
-				}
-			}
-
-			/* reset to read mode */
-			*addr = 0xFFFFFFFF;
-			asm("sync");
-		}
-	}
-
-	printf ("flash erase done\n");
-	return 0;
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-
-int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
-{
-	ulong cp, wp, data;
-	int i, l, rc;
-
-	wp = (addr & ~3);	/* get lower word aligned address */
-
-	/*
-	 * handle unaligned start bytes
-	 */
-	if ((l = addr - wp) != 0) {
-		data = 0;
-		for (i=0, cp=wp; i<l; ++i, ++cp) {
-			data = (data << 8) | (*(uchar *)cp);
-		}
-		for (; i<4 && cnt>0; ++i) {
-			data = (data << 8) | *src++;
-			--cnt;
-			++cp;
-		}
-		for (; cnt==0 && i<4; ++i, ++cp) {
-			data = (data << 8) | (*(uchar *)cp);
-		}
-
-		if ((rc = write_word(info, wp, data)) != 0) {
-			return (rc);
-		}
-		wp += 4;
-	}
-
-	/*
-	 * handle word aligned part
-	 */
-	while (cnt >= 4) {
-		data = 0;
-		for (i=0; i<4; ++i) {
-			data = (data << 8) | *src++;
-		}
-		if ((rc = write_word(info, wp, data)) != 0) {
-			return (rc);
-		}
-		wp  += 4;
-		cnt -= 4;
-	}
-
-	if (cnt == 0) {
-		return (0);
-	}
-
-	/*
-	 * handle unaligned tail bytes
-	 */
-	data = 0;
-	for (i=0, cp=wp; i<4 && cnt>0; ++i, ++cp) {
-		data = (data << 8) | *src++;
-		--cnt;
-	}
-	for (; i<4; ++i, ++cp) {
-		data = (data << 8) | (*(uchar *)cp);
-	}
-
-	return (write_word(info, wp, data));
-}
-
-/*-----------------------------------------------------------------------
- * Write a word to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_word (flash_info_t *info, ulong dest, ulong data)
-{
-	vu_long *addr = (vu_long *)dest;
-	ulong start, csr;
-	int flag;
-
-	/* Check if Flash is (sufficiently) erased */
-	if ((*addr & data) != data) {
-		return (2);
-	}
-	/* Disable interrupts which might cause a timeout here */
-	flag = disable_interrupts();
-
-	/* Write Command */
-	*addr = 0x10101010;
-	asm("sync");
-
-	/* Write Data */
-	*addr = data;
-
-	/* re-enable interrupts if necessary */
-	if (flag)
-		enable_interrupts();
-
-	/* data polling for D7 */
-	start = get_timer (0);
-	flag  = 0;
-
-	while (((csr = *addr) & 0x00800080) != 0x00800080) {
-		if (get_timer(start) > CFG_FLASH_WRITE_TOUT) {
-			flag = 1;
-			break;
-		}
-	}
-	if (csr & 0x40404040) {
-		printf ("CSR indicates write error (%08lx) at %08lx\n", csr, (ulong)addr);
-		flag = 1;
-	}
-
-	/* Clear Status Registers Command */
-	*addr = 0x50505050;
-	asm("sync");
-	/* Reset to read array mode */
-	*addr = 0xFFFFFFFF;
-	asm("sync");
-
-	return (flag);
-}
-
-/*-----------------------------------------------------------------------
- * Clear Block Lock Bit, returns:
- * 0 - OK
- * 1 - Timeout
- */
-
-static int clear_block_lock_bit(vu_long  * addr)
-{
-	ulong start, now;
-
-	/* Reset Array */
-	*addr = 0xffffffff;
-	asm("sync");
-	/* Clear Status Register */
-	*addr = 0x50505050;
-	asm("sync");
-
-	*addr = 0x60606060;
-	asm("sync");
-	*addr = 0xd0d0d0d0;
-	asm("sync");
-
-	start = get_timer (0);
-	while((*addr & 0x00800080) != 0x00800080){
-		if ((now=get_timer(start)) > CFG_FLASH_ERASE_TOUT) {
-			printf ("Timeout on clearing Block Lock Bit\n");
-			*addr = 0xFFFFFFFF;	/* reset bank */
-			asm("sync");
-			return 1;
-		}
-	}
-	return 0;
-}
-
-#endif /* !CFG_NO_FLASH */

board/mpc8560ads/mpc8560ads.c

@@ -214,13 +214,6 @@ typedef struct bcsr_ {
 
 int board_early_init_f (void)
 {
-#if defined(CONFIG_PCI)
-    volatile immap_t *immr = (immap_t *)CFG_IMMR;
-    volatile ccsr_pcix_t *pci = &immr->im_pcix;
-
-    pci->peer &= 0xffffffdf; /* disable master abort */
-#endif
-
     return 0;
 }
 

board/mpl/vcma9/vcma9.c

@@ -119,7 +119,7 @@ int board_init(void)
 	serial_init();
 
 	/* arch number of VCMA9-Board */
-	gd->bd->bi_arch_number = 227;
+	gd->bd->bi_arch_number = MACH_TYPE_MPL_VCMA9;
 
 	/* adress of boot parameters */
 	gd->bd->bi_boot_params = 0x30000100;

board/mx1ads/mx1ads.c

@@ -114,7 +114,7 @@ int board_init (void) {
 
 	SetAsynchMode();
 
-	gd->bd->bi_arch_number = 160;	/* Arch number of MX1ADS Board 		*/
+	gd->bd->bi_arch_number = MACH_TYPE_MX1ADS;
 
 	gd->bd->bi_boot_params = 0x08000100;	/* adress of boot parameters	*/
 

board/mx1fs2/mx1fs2.c

@@ -81,7 +81,7 @@ board_init(void)
 {
 	DECLARE_GLOBAL_DATA_PTR;
 
-	gd->bd->bi_arch_number = 470;
+	gd->bd->bi_arch_number = MACH_TYPE_MX1FS2;
 	gd->bd->bi_boot_params = 0x08000100;
 serial_init();
 	logo_init();

board/nc650/nc650.c

@@ -195,8 +195,7 @@ long int initdram (int board_type)
  * - short between data lines
  */
 
-static long int dram_size (long int mamr_value, long int *base,
-						   long int maxsize)
+static long int dram_size (long int mamr_value, long int *base, long int maxsize)
 {
 	volatile immap_t *immap = (immap_t *) CFG_IMMR;
 	volatile memctl8xx_t *memctl = &immap->im_memctl;
@@ -205,3 +204,14 @@ static long int dram_size (long int mamr_value, long int *base,
 
 	return (get_ram_size(base, maxsize));
 }
+
+#if (CONFIG_COMMANDS & CFG_CMD_NAND)
+void nand_init(void)
+{
+	extern unsigned long nand_probe(unsigned long physadr);
+
+	unsigned long totlen = nand_probe(CFG_NAND_BASE);
+
+	printf ("%4lu MB\n", totlen >> 20);
+}
+#endif

board/ns9750dev/ns9750dev.c

@@ -65,7 +65,7 @@ int board_init( void )
 	/* Active BBUS modules */
 	*get_bbus_reg_addr( NS9750_BBUS_MASTER_RESET ) = 0;
 
-#warning TODO check numbers
+#warning Please register your machine at http://www.arm.linux.org.uk/developer/machines/?action=new
 	/* arch number of OMAP 1510-Board */
 	/* to be changed for OMAP 1610 Board */
 	gd->bd->bi_arch_number = 234;

board/omap1510inn/Makefile

@@ -25,7 +25,7 @@ include $(TOPDIR)/config.mk
 
 LIB	= lib$(BOARD).a
 
-OBJS	:= omap1510innovator.o flash.o
+OBJS	:= omap1510innovator.o
 SOBJS	:= platform.o
 
 $(LIB):	$(OBJS) $(SOBJS)

board/omap1510inn/omap1510innovator.c

@@ -50,7 +50,7 @@ int board_init (void)
 	DECLARE_GLOBAL_DATA_PTR;
 
 	/* arch number of OMAP 1510-Board */
-	gd->bd->bi_arch_number = 234;
+	gd->bd->bi_arch_number = MACH_TYPE_OMAP_INNOVATOR;
 
 	/* adress of boot parameters */
 	gd->bd->bi_boot_params = 0x10000100;

board/omap1510inn/platform.S

@@ -159,8 +159,15 @@ lock_end:
 	 */
 	mov r0, #0x10000000                 /* Load physical SDRAM base. */
 	mov r1, pc                          /* Get current execution location. */
-	cmp r1, r0                          /* Compare. */
-	bge skip_sdram                      /* Skip over EMIF-fast initialization if running from SDRAM. */
+	/* Zero all but top 6 bits of PC, as they alone detect whether an
+	 * address is in the range 0x1000:0000-0x13ff:ffff, the 64M sized
+	 * valid range for SDRAM on the OMAP 1510/5910.
+	 */
+	and r1, r1, #0xfc000000
+	cmp r1, r0			/* Compare. */
+	beq skip_sdram			/* Skip over EMIF-fast initialization
+					 * if running from SDRAM.
+					 */
 
 	/*
 	 * Delay for SDRAM initialization.

board/omap1610inn/omap1610innovator.c

@@ -32,7 +32,6 @@
  */
 
 #include <common.h>
-#include <asm/mach-types.h>
 #if defined(CONFIG_OMAP1610)
 #include <./configs/omap1510.h>
 #endif

board/omap5912osk/omap5912osk.c

@@ -60,9 +60,7 @@ int board_init (void)
 {
 	DECLARE_GLOBAL_DATA_PTR;
 
-	/* arch number of OMAP 1510-Board */
-	/* to be changed for OMAP 1610 Board */
-	gd->bd->bi_arch_number = 234;
+	gd->bd->bi_arch_number = MACH_TYPE_OMAP_OSK;
 
 	/* adress of boot parameters */
 	gd->bd->bi_boot_params = 0x10000100;

board/omap730p2/omap730p2.c

@@ -87,7 +87,7 @@ int board_init (void)
 	DECLARE_GLOBAL_DATA_PTR;
 
 	/* arch number of OMAP 730 P2 Board - Same as the Innovator! */
-	gd->bd->bi_arch_number = 491;
+	gd->bd->bi_arch_number = MACH_TYPE_OMAP_PERSEUS2;
 
 	/* adress of boot parameters */
 	gd->bd->bi_boot_params = 0x10000100;

board/psyent/common/AMDLV065D.c

@@ -0,0 +1,197 @@
+/*
+ * (C) Copyright 2000-2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+
+#include <common.h>
+#if defined(CONFIG_NIOS)
+#include <nios.h>
+#else
+#include <nios2.h>
+#endif
+
+#define SECTSZ		(64 * 1024)
+flash_info_t flash_info[CFG_MAX_FLASH_BANKS];
+
+/*----------------------------------------------------------------------*/
+unsigned long flash_init (void)
+{
+	int i;
+	unsigned long addr;
+	flash_info_t *fli = &flash_info[0];
+
+	fli->size = CFG_FLASH_SIZE;
+	fli->sector_count = CFG_MAX_FLASH_SECT;
+	fli->flash_id = FLASH_MAN_AMD + FLASH_AMDLV065D;
+
+	addr = CFG_FLASH_BASE;
+	for (i = 0; i < fli->sector_count; ++i) {
+		fli->start[i] = addr;
+		addr += SECTSZ;
+		fli->protect[i] = 1;
+	}
+
+	return (CFG_FLASH_SIZE);
+}
+/*--------------------------------------------------------------------*/
+void flash_print_info (flash_info_t * info)
+{
+	int i, k;
+	unsigned long size;
+	int erased;
+	volatile unsigned char *flash;
+
+	printf ("  Size: %ld KB in %d Sectors\n",
+		info->size >> 10, info->sector_count);
+	printf ("  Sector Start Addresses:");
+	for (i = 0; i < info->sector_count; ++i) {
+
+		/* Check if whole sector is erased */
+		if (i != (info->sector_count - 1))
+			size = info->start[i + 1] - info->start[i];
+		else
+			size = info->start[0] + info->size - info->start[i];
+		erased = 1;
+		flash = (volatile unsigned char *) CACHE_BYPASS(info->start[i]);
+		for (k = 0; k < size; k++) {
+			if (*flash++ != 0xff) {
+				erased = 0;
+				break;
+			}
+		}
+
+		/* Print the info */
+		if ((i % 5) == 0)
+			printf ("\n   ");
+		printf (" %08lX%s%s",
+			CACHE_NO_BYPASS(info->start[i]),
+			erased ? " E" : "  ",
+			info->protect[i] ? "RO " : "   ");
+	}
+	printf ("\n");
+}
+
+/*-------------------------------------------------------------------*/
+
+
+int flash_erase (flash_info_t * info, int s_first, int s_last)
+{
+	volatile CFG_FLASH_WORD_SIZE *addr = (CFG_FLASH_WORD_SIZE *)
+		CACHE_BYPASS(info->start[0]);
+	volatile CFG_FLASH_WORD_SIZE *addr2;
+	int prot, sect;
+	ulong start;
+
+	/* Some sanity checking */
+	if ((s_first < 0) || (s_first > s_last)) {
+		printf ("- no sectors to erase\n");
+		return 1;
+	}
+
+	prot = 0;
+	for (sect = s_first; sect <= s_last; ++sect) {
+		if (info->protect[sect]) {
+			prot++;
+		}
+	}
+	if (prot) {
+		printf ("- Warning: %d protected sectors will not be erased!\n",
+			prot);
+	} else {
+		printf ("\n");
+	}
+
+	/* It's ok to erase multiple sectors provided we don't delay more
+	 * than 50 usec between cmds ... at which point the erase time-out
+	 * occurs. So don't go and put printf() calls in the loop ... it
+	 * won't be very helpful ;-)
+	 */
+	for (sect = s_first; sect <= s_last; sect++) {
+		if (info->protect[sect] == 0) {	/* not protected */
+			addr2 = (CFG_FLASH_WORD_SIZE *)
+				CACHE_BYPASS((info->start[sect]));
+			*addr = 0xaa;
+			*addr = 0x55;
+			*addr = 0x80;
+			*addr = 0xaa;
+			*addr = 0x55;
+			*addr2 = 0x30;
+			/* Now just wait for 0xff & provide some user
+			 * feedback while we wait.
+			 */
+			start = get_timer (0);
+			while (*addr2 != 0xff) {
+				udelay (1000 * 1000);
+				putc ('.');
+				if (get_timer (start) > CFG_FLASH_ERASE_TOUT) {
+					printf ("timeout\n");
+					return 1;
+				}
+			}
+		}
+	}
+	printf ("\n");
+	return 0;
+}
+
+/*-----------------------------------------------------------------------
+ * Copy memory to flash, returns:
+ * 0 - OK
+ * 1 - write timeout
+ * 2 - Flash not erased
+ */
+
+int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt)
+{
+
+	vu_char *cmd = (vu_char *) CACHE_BYPASS(info->start[0]);
+	vu_char *dst = (vu_char *) CACHE_BYPASS(addr);
+	unsigned char b;
+	ulong start;
+
+	while (cnt) {
+		/* Check for sufficient erase */
+		b = *src;
+		if ((*dst & b) != b) {
+			printf ("%02x : %02x\n", *dst, b);
+			return (2);
+		}
+
+		*cmd = 0xaa;
+		*cmd = 0x55;
+		*cmd = 0xa0;
+		*dst = b;
+
+		/* Verify write */
+		start = get_timer (0);
+		while (*dst != b) {
+			if (get_timer (start) > CFG_FLASH_WRITE_TOUT) {
+				return 1;
+			}
+		}
+		dst++;
+		src++;
+		cnt--;
+	}
+
+	return (0);
+}

board/psyent/pci5441/Makefile

@@ -0,0 +1,50 @@
+#
+# (C) Copyright 2001-2004
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+COMOBJS := ../common/AMDLV065D.o
+
+OBJS	:= $(BOARD).o $(COMOBJS)
+
+SOBJS	=
+
+$(LIB): $(OBJS) $(SOBJS)
+	$(AR) crv $@ $^
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+-include .depend
+
+#########################################################################

board/psyent/pci5441/config.mk

@@ -0,0 +1,31 @@
+#
+# (C) Copyright 2004, Psyent Corporation <www.psyent.com>
+# Scott McNutt <smcnutt@psyent.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+TEXT_BASE = 0x018e0000
+
+PLATFORM_CPPFLAGS += -mno-hw-div -mno-hw-mul
+PLATFORM_CPPFLAGS += -I$(TOPDIR)/board/$(VENDOR)/include
+
+ifeq ($(debug),1)
+PLATFORM_CPPFLAGS += -DDEBUG
+endif

board/psyent/pci5441/pci5441.c

@@ -0,0 +1,40 @@
+/*
+ * (C) Copyright 2004, Psyent Corporation <www.psyent.com>
+ * Scott McNutt <smcnutt@psyent.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+
+int board_early_init_f (void)
+{
+	return 0;
+}
+
+int checkboard (void)
+{
+	puts ("BOARD : Psyent PCI-5441\n");
+	return 0;
+}
+
+long int initdram (int board_type)
+{
+	return (0);
+}

board/psyent/pci5441/u-boot.lds

@@ -0,0 +1,136 @@
+/*
+ * (C) Copyright 2004, Psyent Corporation <www.psyent.com>
+ * Scott McNutt <smcnutt@psyent.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+
+OUTPUT_FORMAT("elf32-littlenios2")
+OUTPUT_ARCH(nios2)
+ENTRY(_start)
+
+SECTIONS
+{
+	.text :
+	{
+	  cpu/nios2/start.o (.text)
+	  *(.text)
+	  *(.text.*)
+	  *(.gnu.linkonce.t*)
+	  *(.rodata)
+	  *(.rodata.*)
+	  *(.gnu.linkonce.r*)
+	}
+	. = ALIGN (4);
+	_etext = .;
+	PROVIDE (etext = .);
+
+	/* CMD TABLE - sandwich this in between text and data so
+	 * the initialization code relocates the command table as
+	 * well -- admittedly, this is just pure laziness ;-)
+	 */
+	__u_boot_cmd_start = .;
+	.u_boot_cmd :
+	{
+	  *(.u_boot_cmd)
+	}
+	. = ALIGN(4);
+	__u_boot_cmd_end = .;
+
+	/* INIT DATA sections - "Small" data (see the gcc -G option)
+	 * is always gp-relative. Here we make all init data sections
+	 * adjacent to simplify the startup code -- and provide
+	 * the global pointer for gp-relative access.
+	 */
+	_data = .;
+	.data :
+	{
+	  *(.data)
+	  *(.data.*)
+	  *(.gnu.linkonce.d*)
+	}
+
+	. = ALIGN(16);
+	_gp = .;			/* Global pointer addr */
+	PROVIDE (gp = .);
+
+	.sdata :
+	{
+	  *(.sdata)
+	  *(.sdata.*)
+	  *(.gnu.linkonce.s.*)
+	}
+	. = ALIGN(4);
+
+	_edata = .;
+	PROVIDE (edata = .);
+
+	/* UNINIT DATA - Small uninitialized data is first so it's
+	 * adjacent to sdata and can be referenced via gp. The normal
+	 * bss follows. We keep it adjacent to simplify init code.
+	 */
+	__bss_start = .;
+	.sbss :
+	{
+	  *(.sbss)
+	  *(.sbss.*)
+	  *(.gnu.linkonce.sb.*)
+	  *(.scommon)
+	}
+	. = ALIGN(4);
+	.bss :
+	{
+	  *(.bss)
+	  *(.bss.*)
+	  *(.dynbss)
+	  *(COMMON)
+	  *(.scommon)
+	}
+	. = ALIGN(4);
+	_end = .;
+	PROVIDE (end = .);
+
+	/* DEBUG -- symbol table, string table, etc. etc.
+	 */
+	.stab 0 : { *(.stab) }
+	.stabstr 0 : { *(.stabstr) }
+	.stab.excl 0 : { *(.stab.excl) }
+	.stab.exclstr 0 : { *(.stab.exclstr) }
+	.stab.index 0 : { *(.stab.index) }
+	.stab.indexstr 0 : { *(.stab.indexstr) }
+	.comment 0 : { *(.comment) }
+	.debug		0 : { *(.debug) }
+	.line		0 : { *(.line) }
+	.debug_srcinfo	0 : { *(.debug_srcinfo) }
+	.debug_sfnames	0 : { *(.debug_sfnames) }
+	.debug_aranges	0 : { *(.debug_aranges) }
+	.debug_pubnames 0 : { *(.debug_pubnames) }
+	.debug_info	0 : { *(.debug_info) }
+	.debug_abbrev	0 : { *(.debug_abbrev) }
+	.debug_line	0 : { *(.debug_line) }
+	.debug_frame	0 : { *(.debug_frame) }
+	.debug_str	0 : { *(.debug_str) }
+	.debug_loc	0 : { *(.debug_loc) }
+	.debug_macinfo	0 : { *(.debug_macinfo) }
+	.debug_weaknames 0 : { *(.debug_weaknames) }
+	.debug_funcnames 0 : { *(.debug_funcnames) }
+	.debug_typenames 0 : { *(.debug_typenames) }
+	.debug_varnames	 0 : { *(.debug_varnames) }
+}

board/psyent/pk1c20/Makefile

@@ -0,0 +1,50 @@
+#
+# (C) Copyright 2001-2004
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+COMOBJS := ../common/AMDLV065D.o
+
+OBJS	:= $(BOARD).o led.o $(COMOBJS)
+
+SOBJS	=
+
+$(LIB): $(OBJS) $(SOBJS)
+	$(AR) crv $@ $^
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+-include .depend
+
+#########################################################################

board/psyent/pk1c20/config.mk

@@ -0,0 +1,31 @@
+#
+# (C) Copyright 2004, Psyent Corporation <www.psyent.com>
+# Scott McNutt <smcnutt@psyent.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+TEXT_BASE = 0x018e0000
+
+PLATFORM_CPPFLAGS += -mno-hw-div -mno-hw-mul
+PLATFORM_CPPFLAGS += -I$(TOPDIR)/board/$(VENDOR)/include
+
+ifeq ($(debug),1)
+PLATFORM_CPPFLAGS += -DDEBUG
+endif

board/psyent/pk1c20/led.c

@@ -0,0 +1,62 @@
+/*
+ * (C) Copyright 2004, Psyent Corporation <www.psyent.com>
+ * Scott McNutt <smcnutt@psyent.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <nios2.h>
+#include <nios2-io.h>
+#include <status_led.h>
+
+/* The LED port is configured as output only, so we
+ * must track the state manually.
+ */
+static led_id_t val = 0;
+
+void __led_init (led_id_t mask, int state)
+{
+	nios_pio_t *pio = (nios_pio_t *)CACHE_BYPASS(CFG_LEDPIO_ADDR);
+
+	if (state == STATUS_LED_ON)
+		val &= ~mask;
+	else
+		val |= mask;
+	pio->data = val;
+}
+
+void __led_set (led_id_t mask, int state)
+{
+	nios_pio_t *pio = (nios_pio_t *)CACHE_BYPASS(CFG_LEDPIO_ADDR);
+
+	if (state == STATUS_LED_ON)
+		val &= ~mask;
+	else
+		val |= mask;
+	pio->data = val;
+}
+
+void __led_toggle (led_id_t mask)
+{
+	nios_pio_t *pio = (nios_pio_t *)CACHE_BYPASS(CFG_LEDPIO_ADDR);
+
+	val ^= mask;
+	pio->data = val;
+}

board/psyent/pk1c20/pk1c20.c

@@ -0,0 +1,40 @@
+/*
+ * (C) Copyright 2004, Psyent Corporation <www.psyent.com>
+ * Scott McNutt <smcnutt@psyent.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+
+int board_early_init_f (void)
+{
+	return 0;
+}
+
+int checkboard (void)
+{
+	puts ("BOARD : Psyent PK-1C20\n");
+	return 0;
+}
+
+long int initdram (int board_type)
+{
+	return (0);
+}

board/psyent/pk1c20/u-boot.lds

@@ -0,0 +1,136 @@
+/*
+ * (C) Copyright 2004, Psyent Corporation <www.psyent.com>
+ * Scott McNutt <smcnutt@psyent.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+
+OUTPUT_FORMAT("elf32-littlenios2")
+OUTPUT_ARCH(nios2)
+ENTRY(_start)
+
+SECTIONS
+{
+	.text :
+	{
+	  cpu/nios2/start.o (.text)
+	  *(.text)
+	  *(.text.*)
+	  *(.gnu.linkonce.t*)
+	  *(.rodata)
+	  *(.rodata.*)
+	  *(.gnu.linkonce.r*)
+	}
+	. = ALIGN (4);
+	_etext = .;
+	PROVIDE (etext = .);
+
+	/* CMD TABLE - sandwich this in between text and data so
+	 * the initialization code relocates the command table as
+	 * well -- admittedly, this is just pure laziness ;-)
+	 */
+	__u_boot_cmd_start = .;
+	.u_boot_cmd :
+	{
+	  *(.u_boot_cmd)
+	}
+	. = ALIGN(4);
+	__u_boot_cmd_end = .;
+
+	/* INIT DATA sections - "Small" data (see the gcc -G option)
+	 * is always gp-relative. Here we make all init data sections
+	 * adjacent to simplify the startup code -- and provide
+	 * the global pointer for gp-relative access.
+	 */
+	_data = .;
+	.data :
+	{
+	  *(.data)
+	  *(.data.*)
+	  *(.gnu.linkonce.d*)
+	}
+
+	. = ALIGN(16);
+	_gp = .;			/* Global pointer addr */
+	PROVIDE (gp = .);
+
+	.sdata :
+	{
+	  *(.sdata)
+	  *(.sdata.*)
+	  *(.gnu.linkonce.s.*)
+	}
+	. = ALIGN(4);
+
+	_edata = .;
+	PROVIDE (edata = .);
+
+	/* UNINIT DATA - Small uninitialized data is first so it's
+	 * adjacent to sdata and can be referenced via gp. The normal
+	 * bss follows. We keep it adjacent to simplify init code.
+	 */
+	__bss_start = .;
+	.sbss :
+	{
+	  *(.sbss)
+	  *(.sbss.*)
+	  *(.gnu.linkonce.sb.*)
+	  *(.scommon)
+	}
+	. = ALIGN(4);
+	.bss :
+	{
+	  *(.bss)
+	  *(.bss.*)
+	  *(.dynbss)
+	  *(COMMON)
+	  *(.scommon)
+	}
+	. = ALIGN(4);
+	_end = .;
+	PROVIDE (end = .);
+
+	/* DEBUG -- symbol table, string table, etc. etc.
+	 */
+	.stab 0 : { *(.stab) }
+	.stabstr 0 : { *(.stabstr) }
+	.stab.excl 0 : { *(.stab.excl) }
+	.stab.exclstr 0 : { *(.stab.exclstr) }
+	.stab.index 0 : { *(.stab.index) }
+	.stab.indexstr 0 : { *(.stab.indexstr) }
+	.comment 0 : { *(.comment) }
+	.debug		0 : { *(.debug) }
+	.line		0 : { *(.line) }
+	.debug_srcinfo	0 : { *(.debug_srcinfo) }
+	.debug_sfnames	0 : { *(.debug_sfnames) }
+	.debug_aranges	0 : { *(.debug_aranges) }
+	.debug_pubnames 0 : { *(.debug_pubnames) }
+	.debug_info	0 : { *(.debug_info) }
+	.debug_abbrev	0 : { *(.debug_abbrev) }
+	.debug_line	0 : { *(.debug_line) }
+	.debug_frame	0 : { *(.debug_frame) }
+	.debug_str	0 : { *(.debug_str) }
+	.debug_loc	0 : { *(.debug_loc) }
+	.debug_macinfo	0 : { *(.debug_macinfo) }
+	.debug_weaknames 0 : { *(.debug_weaknames) }
+	.debug_funcnames 0 : { *(.debug_funcnames) }
+	.debug_typenames 0 : { *(.debug_typenames) }
+	.debug_varnames	 0 : { *(.debug_varnames) }
+}

board/quantum/Makefile

@@ -0,0 +1,41 @@
+#
+# (C) Copyright 2000
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	= $(BOARD).o fpga.o
+
+
+$(LIB):	.depend $(OBJS)
+	$(AR) crv $@ $(OBJS)
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+sinclude .depend
+
+#########################################################################

board/quantum/config.mk

@@ -0,0 +1,28 @@
+#
+# (C) Copyright 2000
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# RMU boards
+#
+
+TEXT_BASE = 0xfff00000

board/quantum/fpga.c

@@ -0,0 +1,263 @@
+/*
+ * (C) Copyright 2001-2003
+ * Matthias Fuchs, esd gmbh germany, matthias.fuchs@esd-electronics.com
+ * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+/* The DEBUG define must be before common to enable debugging */
+#undef DEBUG
+#include <common.h>
+#include <asm/processor.h>
+#include <command.h>
+#include "fpga.h"
+/* ------------------------------------------------------------------------- */
+
+#define MAX_ONES               226
+
+/* MPC850 port D */
+#define PD(bit) (1 << (15 - (bit)))
+# define FPGA_INIT             PD(11)	/* FPGA init pin (ppc input)     */
+# define FPGA_PRG              PD(12)	/* FPGA program pin (ppc output) */
+# define FPGA_CLK              PD(13)	/* FPGA clk pin (ppc output)     */
+# define FPGA_DATA             PD(14)	/* FPGA data pin (ppc output)    */
+# define FPGA_DONE             PD(15)	/* FPGA done pin (ppc input)     */
+
+
+/* DDR 0 - input, 1 - output */
+#define FPGA_INIT_PDDIR          FPGA_PRG | FPGA_CLK | FPGA_DATA	/* just set outputs */
+
+
+#define SET_FPGA(data)         immr->im_ioport.iop_pddat = (data)
+#define GET_FPGA               immr->im_ioport.iop_pddat
+
+#define FPGA_WRITE_1 {                                                    \
+	SET_FPGA(FPGA_PRG |            FPGA_DATA);  /* set clock to 0 */  \
+	SET_FPGA(FPGA_PRG |            FPGA_DATA);  /* set data to 1  */  \
+	SET_FPGA(FPGA_PRG | FPGA_CLK | FPGA_DATA);  /* set clock to 1 */  \
+	SET_FPGA(FPGA_PRG | FPGA_CLK | FPGA_DATA);}	/* set data to 1  */
+
+#define FPGA_WRITE_0 {                                                    \
+	SET_FPGA(FPGA_PRG |            FPGA_DATA);  /* set clock to 0 */  \
+	SET_FPGA(FPGA_PRG);                         /* set data to 0  */  \
+	SET_FPGA(FPGA_PRG | FPGA_CLK);              /* set clock to 1 */  \
+	SET_FPGA(FPGA_PRG | FPGA_CLK | FPGA_DATA);}	/* set data to 1  */
+
+
+int fpga_boot (unsigned char *fpgadata, int size)
+{
+	volatile immap_t *immr = (immap_t *) CFG_IMMR;
+	int i, index, len;
+	int count;
+
+#ifdef CFG_FPGA_SPARTAN2
+	int j;
+	unsigned char data;
+#else
+	unsigned char b;
+	int bit;
+#endif
+
+	debug ("fpga_boot: fpgadata = %p, size = %d\n", fpgadata, size);
+
+	/* display infos on fpgaimage */
+	printf ("FPGA:");
+	index = 15;
+	for (i = 0; i < 4; i++) {
+		len = fpgadata[index];
+		printf (" %s", &(fpgadata[index + 1]));
+		index += len + 3;
+	}
+	printf ("\n");
+
+
+	index = 0;
+
+#ifdef CFG_FPGA_SPARTAN2
+	/* search for preamble 0xFFFFFFFF */
+	while (1) {
+		if ((fpgadata[index] == 0xff) && (fpgadata[index + 1] == 0xff)
+		    && (fpgadata[index + 2] == 0xff)
+		    && (fpgadata[index + 3] == 0xff))
+			break;	/* preamble found */
+		else
+			index++;
+	}
+#else
+	/* search for preamble 0xFF2X */
+	for (index = 0; index < size - 1; index++) {
+		if ((fpgadata[index] == 0xff)
+		    && ((fpgadata[index + 1] & 0xf0) == 0x30))
+			break;
+	}
+	index += 2;
+#endif
+
+	debug ("FPGA: configdata starts at position 0x%x\n", index);
+	debug ("FPGA: length of fpga-data %d\n", size - index);
+
+	/*
+	 * Setup port pins for fpga programming
+	 */
+	immr->im_ioport.iop_pddir = FPGA_INIT_PDDIR;
+
+	debug ("%s, ", ((GET_FPGA & FPGA_DONE) == 0) ? "NOT DONE" : "DONE");
+	debug ("%s\n", ((GET_FPGA & FPGA_INIT) == 0) ? "NOT INIT" : "INIT");
+
+	/*
+	 * Init fpga by asserting and deasserting PROGRAM*
+	 */
+	SET_FPGA (FPGA_CLK | FPGA_DATA);
+
+	/* Wait for FPGA init line low */
+	count = 0;
+	while (GET_FPGA & FPGA_INIT) {
+		udelay (1000);	/* wait 1ms */
+		/* Check for timeout - 100us max, so use 3ms */
+		if (count++ > 3) {
+			debug ("FPGA: Booting failed!\n");
+			return ERROR_FPGA_PRG_INIT_LOW;
+		}
+	}
+
+	debug ("%s, ", ((GET_FPGA & FPGA_DONE) == 0) ? "NOT DONE" : "DONE");
+	debug ("%s\n", ((GET_FPGA & FPGA_INIT) == 0) ? "NOT INIT" : "INIT");
+
+	/* deassert PROGRAM* */
+	SET_FPGA (FPGA_PRG | FPGA_CLK | FPGA_DATA);
+
+	/* Wait for FPGA end of init period .  */
+	count = 0;
+	while (!(GET_FPGA & FPGA_INIT)) {
+		udelay (1000);	/* wait 1ms */
+		/* Check for timeout */
+		if (count++ > 3) {
+			debug ("FPGA: Booting failed!\n");
+			return ERROR_FPGA_PRG_INIT_HIGH;
+		}
+	}
+
+	debug ("%s, ", ((GET_FPGA & FPGA_DONE) == 0) ? "NOT DONE" : "DONE");
+	debug ("%s\n", ((GET_FPGA & FPGA_INIT) == 0) ? "NOT INIT" : "INIT");
+
+	debug ("write configuration data into fpga\n");
+	/* write configuration-data into fpga... */
+
+#ifdef CFG_FPGA_SPARTAN2
+	/*
+	 * Load uncompressed image into fpga
+	 */
+	for (i = index; i < size; i++) {
+#ifdef CFG_FPGA_PROG_FEEDBACK
+		if ((i % 1024) == 0)
+			printf ("%6d out of %6d\r", i, size);	/* let them know we are alive */
+#endif
+
+		data = fpgadata[i];
+		for (j = 0; j < 8; j++) {
+			if ((data & 0x80) == 0x80) {
+				FPGA_WRITE_1;
+			} else {
+				FPGA_WRITE_0;
+			}
+			data <<= 1;
+		}
+	}
+	/* add some 0xff to the end of the file */
+	for (i = 0; i < 8; i++) {
+		data = 0xff;
+		for (j = 0; j < 8; j++) {
+			if ((data & 0x80) == 0x80) {
+				FPGA_WRITE_1;
+			} else {
+				FPGA_WRITE_0;
+			}
+			data <<= 1;
+		}
+	}
+#else
+	/* send 0xff 0x20 */
+	FPGA_WRITE_1;
+	FPGA_WRITE_1;
+	FPGA_WRITE_1;
+	FPGA_WRITE_1;
+	FPGA_WRITE_1;
+	FPGA_WRITE_1;
+	FPGA_WRITE_1;
+	FPGA_WRITE_1;
+	FPGA_WRITE_0;
+	FPGA_WRITE_0;
+	FPGA_WRITE_1;
+	FPGA_WRITE_0;
+	FPGA_WRITE_0;
+	FPGA_WRITE_0;
+	FPGA_WRITE_0;
+	FPGA_WRITE_0;
+
+	/*
+	 ** Bit_DeCompression
+	 **   Code 1           .. maxOnes     : n                 '1's followed by '0'
+	 **        maxOnes + 1 .. maxOnes + 1 : n - 1             '1's no '0'
+	 **        maxOnes + 2 .. 254         : n - (maxOnes + 2) '0's followed by '1'
+	 **        255                        :                   '1'
+	 */
+
+	for (i = index; i < size; i++) {
+		b = fpgadata[i];
+		if ((b >= 1) && (b <= MAX_ONES)) {
+			for (bit = 0; bit < b; bit++) {
+				FPGA_WRITE_1;
+			}
+			FPGA_WRITE_0;
+		} else if (b == (MAX_ONES + 1)) {
+			for (bit = 1; bit < b; bit++) {
+				FPGA_WRITE_1;
+			}
+		} else if ((b >= (MAX_ONES + 2)) && (b <= 254)) {
+			for (bit = 0; bit < (b - (MAX_ONES + 2)); bit++) {
+				FPGA_WRITE_0;
+			}
+			FPGA_WRITE_1;
+		} else if (b == 255) {
+			FPGA_WRITE_1;
+		}
+	}
+#endif
+	debug ("\n\n");
+	debug ("%s, ", ((GET_FPGA & FPGA_DONE) == 0) ? "NOT DONE" : "DONE");
+	debug ("%s\n", ((GET_FPGA & FPGA_INIT) == 0) ? "NOT INIT" : "INIT");
+
+	/*
+	 * Check if fpga's DONE signal - correctly booted ?
+	 */
+
+	/* Wait for FPGA end of programming period .  */
+	count = 0;
+	while (!(GET_FPGA & FPGA_DONE)) {
+		udelay (1000);	/* wait 1ms */
+		/* Check for timeout */
+		if (count++ > 3) {
+			debug ("FPGA: Booting failed!\n");
+			return ERROR_FPGA_PRG_DONE;
+		}
+	}
+
+	debug ("FPGA: Booting successful!\n");
+	return 0;
+}

board/quantum/fpga.h

@@ -0,0 +1,34 @@
+/*
+ * (C) Copyright 2002
+ * Rich Ireland, Enterasys Networks, rireland@enterasys.com.
+ * Keith Outwater, keith_outwater@mvis.com.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+/*
+ * Virtex2 FPGA configuration support for the QUANTUM computer
+ */
+int fpga_boot(unsigned char *fpgadata, int size);
+
+#define ERROR_FPGA_PRG_INIT_LOW  -1        /* Timeout after PRG* asserted   */
+#define ERROR_FPGA_PRG_INIT_HIGH -2        /* Timeout after PRG* deasserted */
+#define ERROR_FPGA_PRG_DONE      -3        /* Timeout after programming     */
+/* vim: set ts=4 sw=4 tw=78: */

board/quantum/quantum.c

@@ -0,0 +1,257 @@
+/*
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+
+#include <common.h>
+#include <mpc8xx.h>
+#include "fpga.h"
+
+/* ------------------------------------------------------------------------- */
+
+static long int dram_size (long int, long int *, long int);
+unsigned long flash_init (void);
+
+/* ------------------------------------------------------------------------- */
+
+#define	_NOT_USED_	0xFFFFCC25
+
+const uint sdram_table[] = {
+	/*
+	 * Single Read. (Offset 00h in UPMA RAM)
+	 */
+	0x0F03CC04, 0x00ACCC24, 0x1FF74C20, _NOT_USED_,
+	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+
+	/*
+	 * Burst Read. (Offset 08h in UPMA RAM)
+	 */
+	0x0F03CC04, 0x00ACCC24, 0x00FFCC20, 0x00FFCC20,
+	0x01FFCC20, 0x1FF74C20, _NOT_USED_, _NOT_USED_,
+	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+
+	/*
+	 * Single Write. (Offset 18h in UPMA RAM)
+	 */
+	0x0F03CC02, 0x00AC0C24, 0x1FF74C25, _NOT_USED_,
+	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+
+	/*
+	 * Burst Write. (Offset 20h in UPMA RAM)
+	 */
+	0x0F03CC00, 0x00AC0C20, 0x00FFFC20, 0x00FFFC22,
+	0x01FFFC24, 0x1FF74C25, _NOT_USED_, _NOT_USED_,
+	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+
+	/*
+	 * Refresh. (Offset 30h in UPMA RAM)
+	 * (Initialization code at 0x36)
+	 */
+	0x0FF0CC24, 0xFFFFCC24, _NOT_USED_, _NOT_USED_,
+	_NOT_USED_, _NOT_USED_, 0xEFFB8C34, 0x0FF74C34,
+	0x0FFACCB4, 0x0FF5CC34, 0x0FFCC34, 0x0FFFCCB4,
+
+	/*
+	 * Exception. (Offset 3Ch in UPMA RAM)
+	 */
+	0x0FEA8C34, 0x1FB54C34, 0xFFFFCC34, _NOT_USED_
+};
+
+/* ------------------------------------------------------------------------- */
+
+
+/*
+ * Check Board Identity:
+ */
+
+int checkboard (void)
+{
+	unsigned char *s = getenv ("serial#");
+
+	puts ("Board QUANTUM, Serial No: ");
+
+	for (; s && *s; ++s) {
+		if (*s == ' ')
+			break;
+		putc (*s);
+	}
+	putc ('\n');
+	return (0);		/* success */
+}
+
+/* ------------------------------------------------------------------------- */
+
+long int initdram (int board_type)
+{
+	volatile immap_t *immap = (immap_t *) CFG_IMMR;
+	volatile memctl8xx_t *memctl = &immap->im_memctl;
+	long int size9;
+
+	upmconfig (UPMA, (uint *) sdram_table,
+		   sizeof (sdram_table) / sizeof (uint));
+
+	/* Refresh clock prescalar */
+	memctl->memc_mptpr = CFG_MPTPR;
+
+	memctl->memc_mar = 0x00000088;
+
+	/* Map controller banks 1 to the SDRAM bank */
+	memctl->memc_or1 = CFG_OR1_PRELIM;
+	memctl->memc_br1 = CFG_BR1_PRELIM;
+
+	memctl->memc_mamr = CFG_MAMR_9COL & (~(MAMR_PTAE));	/* no refresh yet */
+
+	udelay (200);
+
+	/* perform SDRAM initializsation sequence */
+
+	memctl->memc_mcr = 0x80002136;	/* SDRAM bank 0 */
+	udelay (1);
+
+	memctl->memc_mamr |= MAMR_PTAE;	/* enable refresh */
+
+	udelay (1000);
+
+	/* Check Bank 0 Memory Size,
+	 * 9 column mode
+	 */
+	size9 = dram_size (CFG_MAMR_9COL, (ulong *) SDRAM_BASE_PRELIM,
+			   SDRAM_MAX_SIZE);
+	/*
+	 * Final mapping:
+	 */
+	memctl->memc_or1 = ((-size9) & 0xFFFF0000) | CFG_OR_TIMING_SDRAM;
+	udelay (1000);
+
+	return (size9);
+}
+
+/* ------------------------------------------------------------------------- */
+
+/*
+ * Check memory range for valid RAM. A simple memory test determines
+ * the actually available RAM size between addresses `base' and
+ * `base + maxsize'. Some (not all) hardware errors are detected:
+ * - short between address lines
+ * - short between data lines
+ */
+
+static long int dram_size (long int mamr_value, long int *base,
+			   long int maxsize)
+{
+	volatile immap_t *immap = (immap_t *) CFG_IMMR;
+	volatile memctl8xx_t *memctl = &immap->im_memctl;
+	volatile long int *addr;
+	ulong cnt, val, size;
+	ulong save[32];		/* to make test non-destructive */
+	unsigned char i = 0;
+
+	memctl->memc_mamr = mamr_value;
+
+	for (cnt = maxsize / sizeof (long); cnt > 0; cnt >>= 1) {
+		addr = base + cnt;	/* pointer arith! */
+
+		save[i++] = *addr;
+		*addr = ~cnt;
+	}
+
+	/* write 0 to base address */
+	addr = base;
+	save[i] = *addr;
+	*addr = 0;
+
+	/* check at base address */
+	if ((val = *addr) != 0) {
+		/* Restore the original data before leaving the function.
+		 */
+		*addr = save[i];
+		for (cnt = 1; cnt <= maxsize / sizeof (long); cnt <<= 1) {
+			addr = (volatile ulong *) base + cnt;
+			*addr = save[--i];
+		}
+		return (0);
+	}
+
+	for (cnt = 1; cnt <= maxsize / sizeof (long); cnt <<= 1) {
+		addr = base + cnt;	/* pointer arith! */
+
+		val = *addr;
+		*addr = save[--i];
+
+		if (val != (~cnt)) {
+			size = cnt * sizeof (long);
+			/* Restore the original data before returning
+			 */
+			for (cnt <<= 1; cnt <= maxsize / sizeof (long);
+			     cnt <<= 1) {
+				addr = (volatile ulong *) base + cnt;
+				*addr = save[--i];
+			}
+			return (size);
+		}
+	}
+	return (maxsize);
+}
+
+/*
+ * Miscellaneous intialization
+ */
+int misc_init_r (void)
+{
+	char *fpga_data_str = getenv ("fpgadata");
+	char *fpga_size_str = getenv ("fpgasize");
+	void *fpga_data;
+	int fpga_size;
+	int status;
+	volatile immap_t *immap = (immap_t *) CFG_IMMR;
+	volatile memctl8xx_t *memctl = &immap->im_memctl;
+	int flash_size;
+
+	/* Remap FLASH according to real size */
+	flash_size = flash_init ();
+	memctl->memc_or0 = CFG_OR_TIMING_FLASH | (-flash_size & 0xFFFF8000);
+	memctl->memc_br0 = (CFG_FLASH_BASE & BR_BA_MSK) | BR_MS_GPCM | BR_V;
+
+	if (fpga_data_str && fpga_size_str) {
+		fpga_data = (void *) simple_strtoul (fpga_data_str, NULL, 16);
+		fpga_size = simple_strtoul (fpga_size_str, NULL, 10);
+
+		status = fpga_boot (fpga_data, fpga_size);
+		if (status != 0) {
+			printf ("\nFPGA: Booting failed ");
+			switch (status) {
+			case ERROR_FPGA_PRG_INIT_LOW:
+				printf ("(Timeout: INIT not low after asserting PROGRAM*)\n ");
+				break;
+			case ERROR_FPGA_PRG_INIT_HIGH:
+				printf ("(Timeout: INIT not high after deasserting PROGRAM*)\n ");
+				break;
+			case ERROR_FPGA_PRG_DONE:
+				printf ("(Timeout: DONE not high after programming FPGA)\n ");
+				break;
+			}
+		}
+	}
+	return 0;
+}

board/quantum/u-boot.lds

@@ -0,0 +1,139 @@
+/*
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+/* Do we need any of these for elf?
+   __DYNAMIC = 0;    */
+SECTIONS
+{
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)		}
+  .rela.text     : { *(.rela.text) 	}
+  .rel.data      : { *(.rel.data)		}
+  .rela.data     : { *(.rela.data) 	}
+  .rel.rodata    : { *(.rel.rodata) 	}
+  .rela.rodata   : { *(.rela.rodata) 	}
+  .rel.got       : { *(.rel.got)		}
+  .rela.got      : { *(.rela.got)		}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)		}
+  .rela.bss      : { *(.rela.bss)		}
+  .rel.plt       : { *(.rel.plt)		}
+  .rela.plt      : { *(.rela.plt)		}
+  .init          : { *(.init)	}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    /* WARNING - the following is hand-optimized to fit within	*/
+    /* the sector layout of our flash chips!	XXX FIXME XXX	*/
+
+    cpu/mpc8xx/start.o	(.text)
+    common/dlmalloc.o	(.text)
+    lib_ppc/ppcstring.o	(.text)
+    lib_generic/vsprintf.o	(.text)
+    lib_generic/crc32.o		(.text)
+    lib_generic/zlib.o		(.text)
+/* XXX ?
+    . = env_offset;
+*/
+    common/environment.o(.text)
+
+    *(.text)
+    *(.fixup)
+    *(.got1)
+  }
+  _etext = .;
+  PROVIDE (etext = .);
+  .rodata    :
+  {
+    *(.rodata)
+    *(.rodata1)
+    *(.rodata.str1.4)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x00FF) & 0xFFFFFF00;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
+  __fixup_entries = (. - _FIXUP_TABLE_)>>2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  __u_boot_cmd_start = .;
+  .u_boot_cmd : { *(.u_boot_cmd) }
+  __u_boot_cmd_end = .;
+
+
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(256);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(256);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+  _end = . ;
+  PROVIDE (end = .);
+}

board/quantum/u-boot.lds.debug

@@ -0,0 +1,130 @@
+/*
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+/* Do we need any of these for elf?
+   __DYNAMIC = 0;    */
+SECTIONS
+{
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)		}
+  .rela.text     : { *(.rela.text) 	}
+  .rel.data      : { *(.rel.data)		}
+  .rela.data     : { *(.rela.data) 	}
+  .rel.rodata    : { *(.rel.rodata) 	}
+  .rela.rodata   : { *(.rela.rodata) 	}
+  .rel.got       : { *(.rel.got)		}
+  .rela.got      : { *(.rela.got)		}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)		}
+  .rela.bss      : { *(.rela.bss)		}
+  .rel.plt       : { *(.rel.plt)		}
+  .rela.plt      : { *(.rela.plt)		}
+  .init          : { *(.init)	}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    /* WARNING - the following is hand-optimized to fit within	*/
+    /* the sector layout of our flash chips!	XXX FIXME XXX	*/
+
+    cpu/mpc8xx/start.o	(.text)
+    common/dlmalloc.o	(.text)
+    lib_generic/vsprintf.o	(.text)
+    lib_generic/crc32.o		(.text)
+
+    . = env_offset;
+    common/environment.o(.text)
+
+    *(.text)
+    *(.fixup)
+    *(.got1)
+  }
+  _etext = .;
+  PROVIDE (etext = .);
+  .rodata    :
+  {
+    *(.rodata)
+    *(.rodata1)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x0FFF) & 0xFFFFF000;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
+  __fixup_entries = (. - _FIXUP_TABLE_)>>2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(4096);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(4096);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+  _end = . ;
+  PROVIDE (end = .);
+}

board/sbc8560/config.mk

@@ -22,7 +22,6 @@
 # Foundation, Inc., 59 Temple Place, Suite 330, Boston,
 # MA 02111-1307 USA
 #
-
 #
 # based on mpc8560ads board
 # default CCARBAR is at 0xff700000

board/sbc8560/sbc8560.c

@@ -235,7 +235,11 @@ int checkboard (void)
 
 	get_sys_info (&sysinfo);
 
+#ifdef CONFIG_SBC8560
 	printf ("Board: Wind River SBC8560 Board\n");
+#else
+	printf ("Board: Wind River SBC8540 Board\n");
+#endif
 	printf ("\tCPU: %lu MHz\n", sysinfo.freqProcessor / 1000000);
 	printf ("\tCCB: %lu MHz\n", sysinfo.freqSystemBus / 1000000);
 	printf ("\tDDR: %lu MHz\n", sysinfo.freqSystemBus / 2000000);

board/scb9328/scb9328.c

@@ -29,7 +29,7 @@
 int board_init( void ){
   DECLARE_GLOBAL_DATA_PTR;
 
-  gd->bd->bi_arch_number = 508;
+  gd->bd->bi_arch_number = MACH_TYPE_SCB9328;
   gd->bd->bi_boot_params = 0x08000100;
 
   return 0;

board/shannon/shannon.c

@@ -63,7 +63,7 @@ int board_init (void)
 #endif /* CONFIG_INFERNO */
 
 	/* arch number for shannon */
-	gd->bd->bi_arch_number = 97;
+	gd->bd->bi_arch_number = MACH_TYPE_SHANNON;
 
 	/* adress of boot parameters */
 	gd->bd->bi_boot_params = 0xc0000100;

board/smdk2400/smdk2400.c

@@ -77,7 +77,7 @@ int board_init (void)
 	gpio->OPENCR = 0x0;
 
 	/* arch number of SAMSUNG-Board to MACH_TYPE_SMDK2400 */
-	gd->bd->bi_arch_number = 145;
+	gd->bd->bi_arch_number = MACH_TYPE_SMDK2400;
 
 	/* adress of boot parameters */
 	gd->bd->bi_boot_params = 0x0C000100;

board/smdk2410/smdk2410.c

@@ -104,7 +104,7 @@ int board_init (void)
 	gpio->GPHUP = 0x000007FF;
 
 	/* arch number of SMDK2410-Board */
-	gd->bd->bi_arch_number = 193;
+	gd->bd->bi_arch_number = MACH_TYPE_SMDK2410;
 
 	/* adress of boot parameters */
 	gd->bd->bi_boot_params = 0x30000100;

board/sx1/Makefile

@@ -25,7 +25,7 @@ include $(TOPDIR)/config.mk
 
 LIB	= lib$(BOARD).a
 
-OBJS	:= sx1.o flash.o
+OBJS	:= sx1.o
 SOBJS	:= platform.o
 
 $(LIB):	$(OBJS) $(SOBJS)

board/sx1/flash.c

@@ -1,444 +0,0 @@
-/*
- * (C) Copyright 2001
- * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net
- *
- * (C) Copyright 2004
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <linux/byteorder/swab.h>
-#include <environment.h>
-
-#define PHYS_FLASH_SECT_SIZE	0x00020000	/* 256 KB sectors (x2) */
-flash_info_t flash_info[CFG_MAX_FLASH_BANKS];	/* info for FLASH chips	   */
-
-/* Board support for 1 or 2 flash devices */
-#undef FLASH_PORT_WIDTH32
-#define FLASH_PORT_WIDTH16
-
-#ifdef FLASH_PORT_WIDTH16
-#define FLASH_PORT_WIDTH	ushort
-#define FLASH_PORT_WIDTHV	vu_short
-#define SWAP(x)			__swab16(x)
-#else
-#define FLASH_PORT_WIDTH	ulong
-#define FLASH_PORT_WIDTHV	vu_long
-#define SWAP(x)			__swab32(x)
-#endif
-
-#define FPW	FLASH_PORT_WIDTH
-#define FPWV	FLASH_PORT_WIDTHV
-
-#define mb() __asm__ __volatile__ ("" : : : "memory")
-
-/*-----------------------------------------------------------------------
- * Functions
- */
-static ulong flash_get_size (FPW * addr, flash_info_t * info);
-static int write_data (flash_info_t * info, ulong dest, FPW data);
-static void flash_get_offsets (ulong base, flash_info_t * info);
-void inline spin_wheel (void);
-
-/*-----------------------------------------------------------------------
- */
-
-unsigned long flash_init (void)
-{
-	int i;
-	ulong size = 0;
-
-	for (i = 0; i < CFG_MAX_FLASH_BANKS; i++) {
-		switch (i) {
-		case 0:
-			flash_get_size ((FPW *) PHYS_FLASH_1, &flash_info[i]);
-			flash_get_offsets (PHYS_FLASH_1, &flash_info[i]);
-			break;
-		case 1:
-			flash_get_size ((FPW *) PHYS_FLASH_2, &flash_info[i]);
-			flash_get_offsets (PHYS_FLASH_2, &flash_info[i]);
-			break;
-		default:
-			panic ("configured too many flash banks!\n");
-			break;
-		}
-		size += flash_info[i].size;
-	}
-
-	/* Protect monitor and environment sectors
-	 */
-	flash_protect ( FLAG_PROTECT_SET,
-			CFG_FLASH_BASE,
-			CFG_FLASH_BASE + monitor_flash_len - 1,
-			&flash_info[0]);
-
-	flash_protect ( FLAG_PROTECT_SET,
-			CFG_ENV_ADDR,
-			CFG_ENV_ADDR + CFG_ENV_SIZE - 1,
-			&flash_info[0]);
-
-#ifdef CFG_ENV_ADDR_REDUND
-	flash_protect ( FLAG_PROTECT_SET,
-			CFG_ENV_ADDR_REDUND,
-			CFG_ENV_ADDR_REDUND + CFG_ENV_SIZE_REDUND - 1,
-			&flash_info[0]);
-#endif
-
-	return size;
-}
-
-/*-----------------------------------------------------------------------
- */
-static void flash_get_offsets (ulong base, flash_info_t * info)
-{
-	int i;
-
-	if (info->flash_id == FLASH_UNKNOWN) {
-		return;
-	}
-
-	if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL) {
-		for (i = 0; i < info->sector_count; i++) {
-			info->start[i] = base + (i * PHYS_FLASH_SECT_SIZE);
-			info->protect[i] = 0;
-		}
-	}
-}
-
-/*-----------------------------------------------------------------------
- */
-void flash_print_info (flash_info_t * info)
-{
-	int i;
-
-	if (info->flash_id == FLASH_UNKNOWN) {
-		printf ("missing or unknown FLASH type\n");
-		return;
-	}
-
-	switch (info->flash_id & FLASH_VENDMASK) {
-	case FLASH_MAN_INTEL:
-		printf ("INTEL ");
-		break;
-	default:
-		printf ("Unknown Vendor ");
-		break;
-	}
-
-	switch (info->flash_id & FLASH_TYPEMASK) {
-	case FLASH_28F128J3A:
-		printf ("28F128J3A\n");
-		break;
-	case FLASH_28F640J3A:
-		printf ("28F640J3A\n");
-		break;
-	default:
-		printf ("Unknown Chip Type\n");
-		break;
-	}
-
-	printf ("  Size: %ld MB in %d Sectors\n",
-		info->size >> 20, info->sector_count);
-
-	printf ("  Sector Start Addresses:");
-	for (i = 0; i < info->sector_count; ++i) {
-		if ((i % 5) == 0)
-			printf ("\n   ");
-		printf (" %08lX%s",
-			info->start[i],
-			info->protect[i] ? " (RO)" : "	   ");
-	}
-	printf ("\n");
-	return;
-}
-
-/*
- * The following code cannot be run from FLASH!
- */
-static ulong flash_get_size (FPW * addr, flash_info_t * info)
-{
-	volatile FPW value;
-
-	/* Write auto select command: read Manufacturer ID */
-	addr[0x5555] = (FPW) 0x00AA00AA;
-	addr[0x2AAA] = (FPW) 0x00550055;
-	addr[0x5555] = (FPW) 0x00900090;
-
-	mb ();
-	value = addr[0];
-
-	switch (value) {
-	case (FPW) INTEL_MANUFACT:
-		info->flash_id = FLASH_MAN_INTEL;
-		break;
-	default:
-		info->flash_id = FLASH_UNKNOWN;
-		info->sector_count = 0;
-		info->size = 0;
-		addr[0] = (FPW) 0x00FF00FF;	/* restore read mode */
-		return (0);			/* no or unknown flash	*/
-	}
-
-	mb ();
-	value = addr[1];			/* device ID	    */
-	switch (value) {
-	case (FPW) INTEL_ID_28F128J3A:
-		info->flash_id += FLASH_28F128J3A;
-		info->sector_count = 128;
-		info->size = 0x01000000;
-		break;				/* => 16 MB	*/
-	case (FPW) INTEL_ID_28F640J3A:
-		info->flash_id += FLASH_28F640J3A;
-		info->sector_count = 64;
-		info->size = 0x00800000;
-		break;				/* => 8 MB     */
-	default:
-		info->flash_id = FLASH_UNKNOWN;
-		break;
-	}
-
-	if (info->sector_count > CFG_MAX_FLASH_SECT) {
-		printf ("** ERROR: sector count %d > max (%d) **\n",
-			info->sector_count, CFG_MAX_FLASH_SECT);
-		info->sector_count = CFG_MAX_FLASH_SECT;
-	}
-
-	addr[0] = (FPW) 0x00FF00FF;	/* restore read mode */
-
-	return (info->size);
-}
-
-
-/*-----------------------------------------------------------------------
- */
-
-int flash_erase (flash_info_t * info, int s_first, int s_last)
-{
-	int flag, prot, sect;
-	ulong type, start, last;
-	int rcode = 0;
-
-	if ((s_first < 0) || (s_first > s_last)) {
-		if (info->flash_id == FLASH_UNKNOWN) {
-			printf ("- missing\n");
-		} else {
-			printf ("- no sectors to erase\n");
-		}
-		return 1;
-	}
-
-	type = (info->flash_id & FLASH_VENDMASK);
-	if ((type != FLASH_MAN_INTEL)) {
-		printf ("Can't erase unknown flash type %08lx - aborted\n",
-			info->flash_id);
-		return 1;
-	}
-
-	prot = 0;
-	for (sect = s_first; sect <= s_last; ++sect) {
-		if (info->protect[sect]) {
-			prot++;
-		}
-	}
-
-	if (prot) {
-		printf ("- Warning: %d protected sectors will not be erased!\n",
-			prot);
-	} else {
-		printf ("\n");
-	}
-
-	/*start = get_timer (0); */
-	last = start;
-
-	/* Disable interrupts which might cause a timeout here */
-	flag = disable_interrupts ();
-
-	/* Start erase on unprotected sectors */
-	for (sect = s_first; sect <= s_last; sect++) {
-		if (info->protect[sect] == 0) { /* not protected */
-			FPWV *addr = (FPWV *) (info->start[sect]);
-			FPW status;
-
-			printf ("Erasing sector %2d ... ", sect);
-
-			/* arm simple, non interrupt dependent timer */
-			reset_timer_masked ();
-
-			*addr = (FPW) 0x00500050;	/* clear status register */
-			*addr = (FPW) 0x00200020;	/* erase setup */
-			*addr = (FPW) 0x00D000D0;	/* erase confirm */
-
-			while (((status = *addr) & (FPW) 0x00800080) != (FPW) 0x00800080) {
-				if (get_timer_masked () > CFG_FLASH_ERASE_TOUT) {
-					printf ("Timeout\n");
-					*addr = (FPW) 0x00B000B0;	/* suspend erase     */
-					*addr = (FPW) 0x00FF00FF;	/* reset to read mode */
-					rcode = 1;
-					break;
-				}
-			}
-
-			*addr = (FPW) 0x00500050;	/* clear status register cmd.	*/
-			*addr = (FPW) 0x00FF00FF;	/* resest to read mode		*/
-
-			printf (" done\n");
-		}
-	}
-	return rcode;
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- * 4 - Flash not identified
- */
-
-int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt)
-{
-	ulong cp, wp;
-	FPW data;
-	int count, i, l, rc, port_width;
-
-	if (info->flash_id == FLASH_UNKNOWN) {
-		return 4;
-	}
-/* get lower word aligned address */
-#ifdef FLASH_PORT_WIDTH16
-	wp = (addr & ~1);
-	port_width = 2;
-#else
-	wp = (addr & ~3);
-	port_width = 4;
-#endif
-
-	/*
-	 * handle unaligned start bytes
-	 */
-	if ((l = addr - wp) != 0) {
-		data = 0;
-		for (i = 0, cp = wp; i < l; ++i, ++cp) {
-			data = (data << 8) | (*(uchar *) cp);
-		}
-		for (; i < port_width && cnt > 0; ++i) {
-			data = (data << 8) | *src++;
-			--cnt;
-			++cp;
-		}
-		for (; cnt == 0 && i < port_width; ++i, ++cp) {
-			data = (data << 8) | (*(uchar *) cp);
-		}
-
-		if ((rc = write_data (info, wp, SWAP (data))) != 0) {
-			return (rc);
-		}
-		wp += port_width;
-	}
-
-	/*
-	 * handle word aligned part
-	 */
-	count = 0;
-	while (cnt >= port_width) {
-		data = 0;
-		for (i = 0; i < port_width; ++i) {
-			data = (data << 8) | *src++;
-		}
-		if ((rc = write_data (info, wp, SWAP (data))) != 0) {
-			return (rc);
-		}
-		wp += port_width;
-		cnt -= port_width;
-		if (count++ > 0x800) {
-			spin_wheel ();
-			count = 0;
-		}
-	}
-
-	if (cnt == 0) {
-		return (0);
-	}
-
-	/*
-	 * handle unaligned tail bytes
-	 */
-	data = 0;
-	for (i = 0, cp = wp; i < port_width && cnt > 0; ++i, ++cp) {
-		data = (data << 8) | *src++;
-		--cnt;
-	}
-	for (; i < port_width; ++i, ++cp) {
-		data = (data << 8) | (*(uchar *) cp);
-	}
-
-	return (write_data (info, wp, SWAP (data)));
-}
-
-/*-----------------------------------------------------------------------
- * Write a word or halfword to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_data (flash_info_t * info, ulong dest, FPW data)
-{
-	FPWV *addr = (FPWV *) dest;
-	ulong status;
-	int flag;
-
-	/* Check if Flash is (sufficiently) erased */
-	if ((*addr & data) != data) {
-		printf ("not erased at %08lx (%x)\n", (ulong) addr, *addr);
-		return (2);
-	}
-	/* Disable interrupts which might cause a timeout here */
-	flag = disable_interrupts ();
-
-	*addr = (FPW) 0x00400040;	/* write setup */
-	*addr = data;
-
-	/* arm simple, non interrupt dependent timer */
-	reset_timer_masked ();
-
-	/* wait while polling the status register */
-	while (((status = *addr) & (FPW) 0x00800080) != (FPW) 0x00800080) {
-
-		if (get_timer_masked () > CFG_FLASH_WRITE_TOUT) {
-			*addr = (FPW) 0x00FF00FF;	/* restore read mode */
-			return (1);
-		}
-	}
-
-	*addr = (FPW) 0x00FF00FF;	/* restore read mode */
-
-	return (0);
-}
-
-void inline spin_wheel (void)
-{
-	static int p = 0;
-	static char w[] = "\\/-";
-
-	printf ("\010%c", w[p]);
-	(++p == 3) ? (p = 0) : 0;
-}

board/sx1/sx1.c

@@ -46,7 +46,7 @@ int board_init (void)
 	DECLARE_GLOBAL_DATA_PTR;
 
 	/* arch number of SX1 Board */
-	gd->bd->bi_arch_number = 241;
+	gd->bd->bi_arch_number = MACH_TYPE_SX1;
 
 	/* adress of boot parameters */
 	gd->bd->bi_boot_params = 0x10000100;

board/trab/trab.c

@@ -57,7 +57,7 @@ static void udelay_no_timer (int usec)
 	int i;
 	int delay = usec * 3;
 
-	for (i = 0; i < delay; i ++) gd->bd->bi_arch_number = 145;
+	for (i = 0; i < delay; i ++) gd->bd->bi_arch_number = MACH_TYPE_TRAB;
 }
 #endif /* CONFIG_MODEM_SUPPORT */
 
@@ -109,10 +109,7 @@ int board_init ()
 	gpio->MISCCR = 0x40;
 	gpio->PFCON |= (2<<12);
 
-	/* arch number of SAMSUNG-Board */
-	/* MACH_TYPE_SMDK2400 */
-	/* XXX this isn't really correct, but keep it for now */
-	gd->bd->bi_arch_number = 145;
+	gd->bd->bi_arch_number = MACH_TYPE_TRAB;
 
 	/* adress of boot parameters */
 	gd->bd->bi_boot_params = 0x0c000100;

board/trab/vfd.c

@@ -559,4 +559,13 @@ ulong vfd_setmem (ulong addr)
 	return (size);
 }
 
+/*
+ * Calculate fb size for VIDEOLFB_ATAG. Size returned contains fb,
+ * descriptors and palette areas.
+ */
+ulong calc_fbsize (void)
+{
+	return FRAME_BUF_SIZE;
+}
+
 #endif /* CONFIG_VFD */