It's not possible to disable PCS support just now, an7581 u-boot will not
compile. This patch fixes an issue.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Add required changes to call PCS function to configure the Serdes Port.
The Ethernet driver is adapted following Upstream Kernel node structure.
Function calling order is the same of Phylink upstream kernel.
With the PCS support, also add support for attaching PHY. With
"in-band-status" set in DT for the managed property, a rudimental
support for SFP module is present.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
A fix:
* Fixing compiling MT8195 due to some independent changes that were applied
around the same time as MT8195 support was merged. (CI would not have caught
this since we didn't have a defconfig until now).
And few small features:
* New defconfig for MT8395/Genio 1200 EVK.
* pinctrl support for MT8189-compatible SoCs.
This commit adds an FDT entry for the d0 stepping of the BCM2712 SoC.
This entry is used by the v1.1 revision of the board
(revision & 0x0f == 1).
Signed-off-by: Filip Kokosiński <filip.kokosinski@gmail.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
This patch adds support for multiple FDT files per board model. This is
done by adding the FDTFILES macro, which initializes two rpi_model
struct members: fdtfiles and fdtcount.
The new-style revision codes designate LSB bits as board revision; this
value is used to choose between provided FDTs. The first element of the
fdtfiles list is used should no revision match.
Signed-off-by: Filip Kokosiński <filip.kokosinski@gmail.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Pass the VC logs DT parameter through to the kernel
device tree. This is used by the vclog tool and is
a useful debugging tool.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Matthias Brugger <mbrugger@suse.com>
BCM2711 has different pull-up/down register values compared to BCM2835
- BCM2835: NONE=0, DOWN=1, UP=2
- BCM2711: NONE=0, UP=1, DOWN=2
This patch fixes the pull state register values for BCM2711.
Fixes: 2c39d975f8 ("pinctrl: bcm283x: Add GPIO pull-up/down control for BCM2835 and BCM2711")
Signed-off-by: Cibil Pankiras <cibil.pankiras@egym.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
pcs-airoha-common.o should not build unconditionally,
also make building rules looks better.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Add support for Airoha PCS driver present on AN7581 SoC.
This is needed to configure the Serdes port for the different PHY mode.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Call airoha_switch_init() before creating GDM instances, so if
allocation of GDM port fails, early created GDM instances will work
normally.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
We should not call airoha_fe_init() from GDM port independent code,
because it do a GDM specific things.
Makes airoha_fe_maccr_init() and airoha_fe_init() port dependent
and call them from airoha_eth_port_probe()
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Declare airoha_eth_port as U_BOOT_DRIVER(), fix airoha_alloc_gdm_port()
to lookup a driver instead of direct airoha_eth_port usage.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
In the case of an7581 possible GDM port id are: 1, 2 and 4.
Initialization of port GDM4 will lead to out of boundary writing
to gdm_port_str[] array.
Let's increase the array size by 1 to avoid it.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Rework the driver to support multiple GDM port. The driver is split to
main driver as a MISC driver with forced probe (by using the
DM_FLAG_PROBE_AFTER_BIND) and each GDM port register a ETH driver.
This permit a 1:1 implementation with the linux kernel driver and permit
to use the same exact DT nodes.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Instead of having duplicate priv struct for mdio-mt7531-mmio driver in
both driver and header, use the one exposed by the header directly.
This make sure we have consistent priv struct if the driver will be
updated in the future.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The subclass_code member of the pci_ep_header structure is a 1-byte
field. The macro PCI_CLASS_MEMORY_RAM is a concetation of baseclass_code
and subclass_code as follows:
PCI_BASE_CLASS_MEMORY: 0x05
Subclass Code for RAM: 0x00
PCI_CLASS_MEMORY_RAM: 0x0500
Hence, instead of extracting it via an implicity type conversion from int
to u8 which throws a warning, explicitly mask the bits to extract the
subclass_code.
Fixes: cde77583cf ("spl: Add support for Device Firmware Upgrade (DFU) over PCIe")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Tested-by: Anshul Dalal <anshuld@ti.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Tested-by: Mattijs Korpershoek <mkorpershoek@kernel.org> # am62x_evm_a53
Link: https://lore.kernel.org/r/20260305103815.999886-1-s-vadapalli@ti.com
Signed-off-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Add minimal infrastructure to build SPL images with support for UFS
storage devices. This also pulls in SCSI support and charset functions,
which are dependencies of the UFS code.
With this, only a fixed offset is supported for loading the next image,
which should be specified in CONFIG_SPL_UFS_RAW_U_BOOT_SECTOR as the
number of 4096-byte sectors into the UFS block device.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Link: https://patch.msgid.link/20260120-rk3576-ufs-v5-1-0edb61b301b7@gmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Frieder reports that after the kbuild sync running
make tools-only_defconfig
make cross_tools
fails with
UPD include/generated/timestamp_autogenerated.h
PYMOD rebuild
tools/Makefile:359: *** insufficient number of arguments (1) to function
'filter'. Stop.
make: *** [Makefile:2191: tools] Error 2
After the sync 'hostprogs-always-y' contains the complete list of
the tools we need to strip, so the $(filter) command is not needed.
Fixes: bd3f9ee679 ("kbuild: Bump the build system to 6.1")
Reported-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Enable firmware TPM (fTPM) support via OP-TEE for K3 platforms with
MMC hardware. This provides TPM 2.0 functionality through
Microsoft's fTPM Trusted Application running in OP-TEE secure world,
using eMMC RPMB as persistent storage.
fTPM support in U-Boot provides the foundation for measured boot
and disk encryption use cases.
The ARM64 condition ensures these apply only to A53/A72 cores and the
MMC condition ensures fTPM is enabled only on platforms with eMMC
hardware support.
Signed-off-by: Shiva Tripathi <s-tripathi1@ti.com>
Acked-by: Andrew Davis <afd@ti.com>
* The symbol for the x86 architecture is CONFIG_X86 and not CONFIG_x86.
* Correct the description. The partition type is called MBR.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
We removed configuration symbol CONFIG_DM_PCI with
commit 3232bdf0b3 ("pci: Drop DM_PCI").
Don't select it for TARGET_POMELO.
Fixes: b9d0f00a9d ("arm: add initial support for the Phytium Pomelo Board")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Varadarajan Narayanan <varadarajan.narayanan@oss.qualcomm.com> says:
The disk_read() and disk_write() functions of the FAT driver use the
blk_dread() and blk_dwrite() respectively. The blk_* APIs read and write
to the devices in terms of the device block size. However, the FAT
driver reads in terms of the device block size (from fat_set_blk_dev and
read_bootsectandvi) and sector size in the rest of the places.
This causes buffer overflows or partial reads when the FAT sector size
is not equal to device block size. Fix this by using blk_dread in
fat_set_blk_dev and read_bootsectandvi instead of disk_read. And update
disk_read/disk_write to handle FAT sector size and block size mismatch.
Tested on
blksz | FAT sector size
------+----------------
4096 | 4096
512 | 512
4096 | 512
512 | 4096
CI test results
---------------
https://github.com/u-boot/u-boot/pull/871
All checks have passed
93 successful checks
No conflicts with base branch
Code size change info
---------------------
arm: (for 1/1 boards) all +32.0 text +32.0
qemu_arm : all +32 text +32
u-boot: add: 0/0, grow: 2/0 bytes: 24/0 (24)
function old new delta
read_bootsectandvi 420 432 +12
fat_set_blk_dev 204 216 +12
aarch64: (for 1/1 boards) all +12.0 rodata -8.0 text +20.0
qemu_arm64 : all +12 rodata -8 text +20
u-boot: add: 0/0, grow: 2/0 bytes: 20/0 (20)
function old new delta
read_bootsectandvi 408 420 +12
fat_set_blk_dev 204 212 +8
aarch64: (for 1/1 boards) all -2.0 data -8.0 rodata +6.0
qcom_qcs9100 : all -2 data -8 rodata +6
u-boot: add: 1/-1, grow: 8/-1 bytes: 708/-224 (484)
function old new delta
disk_rw - 628 +628
read_bootsectandvi 408 428 +20
fat_itr_root 500 520 +20
get_cluster 376 388 +12
set_contents 2076 2084 +8
fat_set_blk_dev 204 212 +8
static.set_fatent_value 536 540 +4
get_fatent 420 424 +4
fat_next_cluster 368 372 +4
disk_read 100 - -100
disk_write 132 8 -124
Link: https://lore.kernel.org/r/20260224035000.1617869-1-varadarajan.narayanan@oss.qualcomm.com
Enable FS_FAT_HANDLE_SECTOR_SIZE_MISMATCH to handle the different
combination of FAT sector size and device block size present in QCOM
platforms.
Signed-off-by: Varadarajan Narayanan <varadarajan.narayanan@oss.qualcomm.com>
The disk_read() and disk_write() functions of the FAT driver use the
blk_dread() and blk_dwrite() respectively. The blk_* APIs read and write
to the devices in terms of the device block size. However, the FAT
driver reads in terms of the device block size (from fat_set_blk_dev and
read_bootsectandvi) and sector size in the rest of the places.
This causes buffer overflows or partial reads when the FAT sector size
is not equal to device block size. Fix this by using blk_dread in
fat_set_blk_dev and read_bootsectandvi instead of disk_read. And update
disk_read/disk_write to handle FAT sector size and block size mismatch.
Tested on
blksz | FAT sector size
------+----------------
4096 | 4096
512 | 512
4096 | 512
512 | 4096
Signed-off-by: Varadarajan Narayanan <varadarajan.narayanan@oss.qualcomm.com>
Booting into SPL using ramboot can take several seconds on some SoCs due
to the large size of the usb472 payload sent over USB to BootROM.
A large chunk of the usb472 payload, around 1-2 MiB, is padding used to
avoid overlapping when loading e.g. TF-A to 0x40000.
BootROM is likely wasting unnecessary time crc16 validating the padding
of the payload.
Place the FIT payload directly after SPL and memmove it to the expected
memory location, SPL_LOAD_FIT_ADDRESS, to avoid excessive padding and
help speed up ramboot.
Binman symbols are used to get the position and size of the FIT payload
that is initially loaded into DRAM by the BootROM.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The ATAGS set by Rockchip DDR init blob[1] specify DRAM banks above the
first addressable 4GiB which we haven't done in the mem_map for RK3588
yet.
For 4GiB DRAM, the 256MiB missing from the first addressable 4GiB (due
to MMIO) are accessible at the end of the 8GiB address space. For 8GiB,
4-8GiB address space is used for the additional 4GiB and the missing
256MiB are at the end of 12GiB address space. For 12, 4-12GiB and the
missing 256MiB at the end of 20GiB address space. For 16GiB, 4-~16GiB
with two holes (reasons unknown) around 16GiB and the missing 256MiB is
at the end of 20GiB address space. For 32GiB, 4-16~GiB with two holes
and then 16GiB to 32GiB address space (so likely missing 256MiB from
MMIO address space).
[1] https://gist.github.com/Kwiboo/1c020d37e3adbc9d0d79dc003d921977
Suggested-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rockchip RK3506 is a ARM-based SoC with tri-core Cortex-A7.
Add initial arch support for the RK3506 SoC.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Acked-by: Mattijs Korpershoek <mkorpershoek@kernel.org> # drivers/usb/gadget
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rockchip RK3506 has two Ethernet controllers based on Synopsys DWC
Ethernet QoS IP.
Add initial support for the RK3506 GMAC variant.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for the OTP controller in RK3506. The OTPC is similar to the
OTPC in RK3568 and can use the same ops for reading OTP data.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add pinctrl driver for RK3506.
Imported from vendor U-Boot linux-6.1-stan-rkr6 tag with adjustments
to use regmap_update_bits().
Signed-off-by: Ye Zhang <ye.zhang@rock-chips.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Tested-by: Aaron Griffith <aargri@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add clock driver for RK3506.
Imported from vendor U-Boot linux-6.1-stan-rkr6 tag with minor
adjustments and fixes for mainline.
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
