With the migration to DM_SERIAL in commit 191b10ac70 ("PowerPC /
Layerscape: Finish migration to DM_SERIAL") a number of platforms were
incorrectly migrated and did not enable SYS_NS16550 despite previously
having enabled the non-DM NS16650 serial driver. Enable these now.
Fixes: 191b10ac70 ("PowerPC / Layerscape: Finish migration to DM_SERIAL")
Reported-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Commit bb6f3c0f76 ("armv7: ls102xa: Update SCFG_QSPI_CLKSEL value")
broke the SPI boot on the LS1021ATSN board (ls1021atsn_qspi_defconfig)
at least.
The commit message reads
Update SCFG_QSPI_CLKSEL value : 0xC -> 0x5
which means ClusterPLL/16
The original submitted patch had the following description:
Value 0xC is reserved. Replace it with correct value 0x5 which
is ClusterPLL/16
Unfortunatly, the little information which was there, was stripped even
further. Why is 0x5 the "correct" value? In fact, it seems that the
upper bit is just ignored and thus the value 0xC translates to 0x4 which
is ClusterPLL/20. This, will result in a SPI clock of 60MHz (if the PLL
is clocked at 1.2GHz). But even that is too much for the (default) 03h
read opcode (max 50MHz). Set the value to ClusterPLL/24 which is 50MHz.
Link: https://lore.kernel.org/r/1568804284-25162-1-git-send-email-kuldeep.singh@nxp.com/
Fixes: bb6f3c0f76 ("armv7: ls102xa: Update SCFG_QSPI_CLKSEL value")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Switching to DM_SERIAL disabled any serial driver. Re-enable it again.
Fixes: 191b10ac70 ("PowerPC / Layerscape: Finish migration to DM_SERIAL")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since switching to DM_SERIAL 'stdout-path' seems to be necessary.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Related to the problem resolved with commit 2092322b31 ("boot: Add
fit_config_get_hash_list() to build signed node list"), add a testcase
for the problem as well.
Reported-by: Apple Security Engineering and Architecture (SEAR)
Signed-off-by: Tom Rini <trini@konsulko.com>
The functions use 'ulong', however, the comments said 'uint32_t'.
Update the comments to match the prototype.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
The MT7622 infracfg and pericfg drivers both use
mtk_common_clk_infrasys_init() for probe, which populates struct
mtk_clk_priv and stores gate definitions in the clk_tree. However,
both drivers were incorrectly wired to mtk_clk_gate_ops which expects
struct mtk_cg_priv with separately populated gates/num_gates/gates_offs
fields from mtk_common_clk_gate_init().
Since those fields were never set, any attempt to enable an infracfg or
pericfg gate clock (e.g. CLK_INFRA_TRNG) would fail with -EINVAL.
Switch both to mtk_clk_infrasys_ops and struct mtk_clk_priv to match
the init function.
Fixes: 72ab603b20 ("clk: mediatek: add driver for MT7622")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Updates for RPi for 2026.04-rc4:
- board/raspberrypi: add bcm2712d0-rpi-5-b for Raspberry Pi 5
- board/raspberrypi: add multi-FDT support
- rpi: pass the Video Core logs DT parameter through
- pinctrl: bcm283x: Fix GPIO pull state register values for BCM2711
This commit adds an FDT entry for the d0 stepping of the BCM2712 SoC.
This entry is used by the v1.1 revision of the board
(revision & 0x0f == 1).
Signed-off-by: Filip Kokosiński <filip.kokosinski@gmail.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
This patch adds support for multiple FDT files per board model. This is
done by adding the FDTFILES macro, which initializes two rpi_model
struct members: fdtfiles and fdtcount.
The new-style revision codes designate LSB bits as board revision; this
value is used to choose between provided FDTs. The first element of the
fdtfiles list is used should no revision match.
Signed-off-by: Filip Kokosiński <filip.kokosinski@gmail.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Pass the VC logs DT parameter through to the kernel
device tree. This is used by the vclog tool and is
a useful debugging tool.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Matthias Brugger <mbrugger@suse.com>
BCM2711 has different pull-up/down register values compared to BCM2835
- BCM2835: NONE=0, DOWN=1, UP=2
- BCM2711: NONE=0, UP=1, DOWN=2
This patch fixes the pull state register values for BCM2711.
Fixes: 2c39d975f8 ("pinctrl: bcm283x: Add GPIO pull-up/down control for BCM2835 and BCM2711")
Signed-off-by: Cibil Pankiras <cibil.pankiras@egym.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Frieder reports that after the kbuild sync running
make tools-only_defconfig
make cross_tools
fails with
UPD include/generated/timestamp_autogenerated.h
PYMOD rebuild
tools/Makefile:359: *** insufficient number of arguments (1) to function
'filter'. Stop.
make: *** [Makefile:2191: tools] Error 2
After the sync 'hostprogs-always-y' contains the complete list of
the tools we need to strip, so the $(filter) command is not needed.
Fixes: bd3f9ee679 ("kbuild: Bump the build system to 6.1")
Reported-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
The hashed-nodes property in a FIT signature node lists which FDT paths
are included in the signature hash. It is intended as a hint so should
not be used for verification.
Add a function to build the node list from scratch by iterating the
configuration's image references. Skip properties known not to be image
references. For each image, collect the path plus all hash and cipher
subnodes.
Use the new function in fit_config_check_sig() instead of reading
'hashed-nodes'.
Update the test_vboot kernel@ test case: fit_check_sign now catches the
attack at signature-verification time (the @-suffixed node is hashed
instead of the real one, causing a mismatch) rather than at
fit_check_format() time.
Update the docs to cover this. The FIT spec can be updated separately.
Signed-off-by: Simon Glass <simon.glass@canonical.com>
Closes: https://lore.kernel.org/u-boot/20260302220937.3682128-1-trini@konsulko.com/
Reported-by: Apple Security Engineering and Architecture (SEAR)
Tested-by: Tom Rini <trini@konsulko.com>
The PCIe0 instance of PCIe on the J722S SoC uses the 4 GB Address Window
starting from 0x6_0000_0000 to map System Addresses to PCIe Bus Addresses.
Hence, enable CONFIG_SYS_PCI_64BIT.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Fixes: 79f3e77133 ("Subtree merge tag 'v6.16-dts' of dts repo [1] into dts/upstream")
The PCIe1 instance of PCIe on the J7200 SoC uses the 4 GB Address Window
starting from 0x41_0000_0000 to map System Addresses to PCIe Bus Addresses.
Hence, enable CONFIG_SYS_PCI_64BIT.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Fixes: 79f3e77133 ("Subtree merge tag 'v6.16-dts' of dts repo [1] into dts/upstream")
The PCIe0 instance of PCIe on the AM64x SoC uses the 4 GB Address Window
starting from 0x6_0000_0000 to map System Addresses to PCIe Bus Addresses.
Hence, enable CONFIG_SYS_PCI_64BIT.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Fixes: 79f3e77133 ("Subtree merge tag 'v6.16-dts' of dts repo [1] into dts/upstream")
The PCIe Controllers on the J784S4 and AM69 SoCs support Root-Complex
mode of operation. PCIe0 instance of PCIe on both of the SoCs is brought
out on the Starter-Kit (AM69) and EVM (J784S4) boards. Hence, enable
the configs required for Root-Complex mode of operation.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Fixes: 79f3e77133 ("Subtree merge tag 'v6.16-dts' of dts repo [1] into dts/upstream")
The PCIe Controllers on the J784S4 SoC support Root-Complex mode of
operation. Hence, enable it.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Fixes: 79f3e77133 ("Subtree merge tag 'v6.16-dts' of dts repo [1] into dts/upstream")
The PCIe Controllers in the K3 SoCs have 4 GB Address Windows in the
64-bit address space to map System (CPU) Addresses to PCIe Bus Addresses.
The physical addresses for these Address Windows across PCIe instances
across SoCs is as follows:
+--------+----------------+----------------+----------------+----------------+
| SoC | PCIe0 | PCIe1 | PCIe2 | PCIe3 |
+--------+----------------+----------------+----------------+----------------+
| AM64 | 0x6_0000_0000 | NA | NA | NA |
| J722S | 0x6_0000_0000 | NA | NA | NA |
| AM68 | NA | 0x41_0000_0000 | NA | NA |
| J7200 | NA | 0x41_0000_0000 | NA | NA |
| J721S2 | NA | 0x41_0000_0000 | NA | NA |
| J742S2 | 0x40_0000_0000 | 0x41_0000_0000 | NA | NA |
| AM69 | 0x40_0000_0000 | 0x41_0000_0000 | 0x42_0000_0000 | 0x43_0000_0000 |
| J721E | 0x40_0000_0000 | 0x41_0000_0000 | 0x42_0000_0000 | 0x43_0000_0000 |
| J784S4 | 0x40_0000_0000 | 0x41_0000_0000 | 0x42_0000_0000 | 0x43_0000_0000 |
+--------+----------------+----------------+----------------+----------------+
Two regions for a 1:1 mapping from virtual addresses to physical addresses
catering to all of the above will be required, which are:
1. For AM64 and J722S SoCs
=> Start: 0x6_0000_0000 Size: 0x1_0000_0000
2. For AM68, AM69, J7200, J721E, J721S2, J742S2 and J784S4 SoCs
=> Start: 0x40_0000_0000 Size: 0x4_0000_0000
Since the 'Flash Peripherals' region from 0x5_0000_0000 to 0x8_7FFF_FFFF
includes the mapping for AM64 and J722S SoCs, only the second region
mentioned above needs to be added.
Hence, add the region to support 64-bit address space for PCIe.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Fixes: 79f3e77133 ("Subtree merge tag 'v6.16-dts' of dts repo [1] into dts/upstream")
Drivers should extract device-tree data before probing via the
.of_to_plat hook.
Implement it for stm32_dsi driver. By doing so, it also solve a
variable shadowing in stm32_dsi_probe() where &clk was used as
peripheral clock and ref clock.
For readability some struct have been renamed such as:
* struct stm32_dsi_priv *dsi -> struct stm32_dsi_priv *priv
* struct clk clk -> struct clk pclk
Signed-off-by: Raphael Gallais-Pou <rgallaispou@gmail.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Philip Molloy <philip@philipmolloy.com> says:
This series updates the maintainers for the ADI ADSP platform. It
follows Greg's series adding support for ADI ADSP SoCs.
Timesys spent years developing and maintaining Linux support for ADI
ADSP SoCs. The maintenance contract has ended and ADI has brought that
effort in-house. Additionally, Timesys was acquired by another company.
Thanks to everyone at Timesys for all of their hard work over the years!
Link: https://lore.kernel.org/r/20260226111136.354009-1-philip@philipmolloy.com
After years of developing the ADI ADSP platform, Timesys was purchased
by another company and is no longer contracted to maintain the platform.
Signed-off-by: Philip Molloy <philip.molloy@analog.com>
Reviewed-by: Greg Malysa <malysagreg@gmail.com>
After years of developing the ADI ADSP platform, Timesys was purchased
by another company and is no longer contracted to maintain the platform.
Utsav is leaving ADI after contributing to ADSP SoCs for the last 3
years. He is a founding member of the in-house team supporting the
chips.
Linux support at ADI has been consolidated. Use the company-wide mailing
list and git repository.
Signed-off-by: Philip Molloy <philip.molloy@analog.com>
Reviewed-by: Greg Malysa <malysagreg@gmail.com>
More strict checks in GCC 15 expose a new warning:
tools/atmelimage.c: In function ‘atmel_find_pmecc_parameter_in_token’:
tools/atmelimage.c:64:31: error: assignment discards ‘const’ qualifier from pointer target type [-Werror=discarded-qualifiers]
64 | param = strstr(token, "=");
| ^
cc1: all warnings being treated as errors
Add 'const' qualifier to variable 'param' to prevent build failing
due to -Werror.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
A few fixes/missing changes for UFS:
- remove unused ufs_post_bind() declaration
- Disable UTP command timeout in slow mode
- Missing MediaTek UFS PHY Driver to be used with the UFS driver
Remove the "phandle = <0x..>;" properties from the DT diff between
unpatched base DT and U-Boot augmented DT if DEVICE_TREE_DEBUG=1.
The phandle numbers are only generated by DTC, but not referenced
anywhere in the DT, because the original references are specifically
not replaced by phandle numbers when recent DTC is invoked with the
-I dts -O dts flags . The phandle number are therefore only a noise
in the diff, filter them out.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Tested-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
The exported sub_make_done variable leaks into the environment of all
child processes. When make targets like tcheck spawn independent make
invocations with O=, those child makes inherit sub_make_done=1, skip
the KBUILD_OUTPUT setup and try to build in the source tree.
There is a workaround that resets sub_make_done to 0 for specific test
targets, but this isn't great since it has tolist every target that
spawns independent make invocations.
Instead, unexport sub_make_done once we are in the final make
invocation. The direct sub-make already has the value in its
environment from the export, and no further propagation is needed.
This also allows the per-target workaround to be removed.
Fixes: 27529f1cb0 ("kbuild: skip parsing pre sub-make code for recursion")
Signed-off-by: Simon Glass <simon.glass@canonical.com>
The bootmenu_conv_key() function is shared with expo subsystem for key
input. Adding alphanumeric-to-BKEY_SHORTCUT conversion there causes expo
to swallow typed characters instead of inserting them as text, since
BKEY_SHORTCUT falls in the range that expo treats as a command key
rather than passing through.
Move the shortcut-key detection into bootmenu_loop() where it is
only used in the bootmenu context.
Fixes: 8c986521c3 ("cmd: bootmenu: permit to select bootmenu entry with a shortcut")
Signed-off-by: Simon Glass <simon.glass@canonical.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The ofnode_to_fdt() function may return a NULL pointer in multiple cases.
Or, this function's return value is often passed directly to functions such
as fdt_getprop() which end up dereferencing it, thus causing a NULL pointer
exception.
Don't allow ofnode_to_fdt() to return NULL, to avoid a NULL pointer
dereference.
Reviewed-by: Raphaël Gallais-Pou <raphael.gallais-pou@foss.st.com>
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
Reviewed-by: Simon Glass <simon.glass@canonical.com>
The get_ram_size() function fails to restore the original RAM data when
the data cache is enabled. This issue was observed on an AM625 R5 SPL
with 512MB of RAM and is a regression that became visible with
commit bc07851897 ("board: ti: Pull redundant DDR functions to a common
location and Fixup DDR size when ECC is enabled").
Observed boot failure messages:
Warning: Did not detect image signing certificate. Skipping authentication to prevent boot failure. This will fail on Security Enforcing(HS-SE) devices
Authentication passed
Starting ATF on ARM64 core...
The system then hangs. This indicates that without a data cache flush,
data in the cache is not coherent with RAM, preventing the system from
booting. This was verified by printing the content of this address when
the issue occurs.
Add a data cache flush after each restore operation to resolve this
issue.
Fixes: bc07851897 ("board: ti: Pull redundant DDR functions to a common location and Fixup DDR size when ECC is enabled")
Fixes: 1c64b98c1e ("common/memsize.c: Fix get_ram_size() when cache is enabled")
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Reviewed-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Tested-by: Francesco Dolcini <francesco.dolcini@toradex.com> # Toradex Verdin AM62
Commit 067c1b0332 ("ufs: Call ufs_scsi_bind() from uclass .post_bind")
inlined ufs_scsi_bind() into ufs_post_bind() as trivial
device_bind_driver() call.
ufs_scsi_bind() is no longer referenced anywhere in the codebase, so
drop its declaration from include/ufs.h.
Drivers used to include <ufs.h> to include prototype of ufs_scsi_bind()
function, so we can now safely remove such includes.
Fixes: 067c1b0332 ("ufs: Call ufs_scsi_bind() from uclass .post_bind")
Signed-off-by: Julien Stephan <jstephan@baylibre.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20260203-cleanup-ufs-header-v1-1-4c10424485f0@baylibre.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Add a test calling the LoadImage() UEFI function with both its SourceBuffer
and DevicePath input arguments equal to NULL.
This test can be run on the sandbox with the following command:
./u-boot -T -c "setenv efi_selftest load image from file; \
bootefi selftest"
Signed-off-by: Vincent Stehlé <vincent.stehle@arm.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Cc: Tom Rini <trini@konsulko.com>
With the change to regularize the usage of TEST_PY_TEST_SPEC in the
sjg-lab stanza with commit c7f360f20d ("Gitlab: Rework sjg-lab calling
test.py to be closer to test.py stage") the leading "and " part of the
usage under qemu-x86_64 wasn't removed when it should have been. Do so
now.
Fixes: c7f360f20d ("Gitlab: Rework sjg-lab calling test.py to be closer to test.py stage")
Reviewed-by: Simon Glass <simon.glass@canonical.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
