This restores support for IOT2050 by widely synchronizing its DT files
with the Linux kernel. We additionally need to add the alias restoration
that is still waiting for its upstream merge and the not-yet-upstreamed
bits needed for watchdog reboot detection.
Fixes: 4dbdc84754 ("arm: dts: k3-am654: pull in dtb update from Linux")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Kernel commit 1b77265626a4 ("arm64: dts: ti: k3-j7200-mcu-wakeup: Add
HyperBus node") was merged to kernel without its dependent patch [1].
Similar fix is needed in U-Boot, and hbmc currently breaks boot. Till
this gets fixed in U-Boot, disable the config by default so that the
hbmc probe that happens in board/ti/j721e/evm.c will not take place
and lead to boot failure.
This is similar to the approach in commit 5b2671594b ("configs:
j721e: Remove HBMC_AM654 config"), introduced to j7200 evm platform.
[1] https://lore.kernel.org/all/20230424184810.29453-1-afd@ti.com/
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
A "F: foo*" entry does not match any foo*/ folder nor its subtree,
another "F: foo*/" entry is needed for that.
Add missing foo*/ entries where an existing folder was ignored,
so this folder and its subtree is properly covered.
Arm tegra, Arm TI and Environment sections are affected.
Cc: Tom Rini <trini@konsulko.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Svyatoslav Ryhel <clamor95@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Anthony Loiseau <anthony.loiseau@allcircuits.com>
Commit 19a91f2464 ("Create a new boot/ directory") moved the
android_ab.c code under boot/android_ab but did not update
the MAINTAINERS entry.
Update it so that the maintainer will get cc'ed again.
Fixes: 19a91f2464 ("Create a new boot/ directory")
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
main_timer0 is used by u-boot as the tick-timer. Add it to the soc
devices list so it an be enabled via the k3 power controller.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Bryan Brattlof <bb@ti.com> says:
Hello Again Everyone!
This series gets the am65x booting again along with syncing the device
tree files with v6.7-rc1 Linux.
The bulk of these patches unify the WKUP SPL board file with the arm64
files to make future syncs from Linux much easier. In the end the DTBs
should look a lot like what the DTBs look like for the am64x which
is fairly similar to the am65x.
For those interested in what UART boot looks like:
https://paste.sr.ht/~bryanb/7df8a645dc548912cd806abd5ecab967ef3287bc
Many nodes are reused between WKUP SPL, MAIN SPL, and U-Boot. Using
bootph-pre-ram is causing these nodes to be present in SPL builds but
pruned away during the U-Boot build. Convert these nodes to bootph-all
so they will remain no matter which dtb build is happening.
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board dtb files unified, we now have a
duplicate mcu secure proxy node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
The dummy_clock node is used to help the drivers probe the IO needed to
setup consoles and boot media to load firmware into the SoC.
This dummy_clock isn't a device that exists nor does it exist in the
mcu domain. So move it from cbass_mcu to the root node to avoid any
confusion.
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
These aliases are not needed in U-Boot. Remove them
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board dtb files unified, we have duplicate
properties in the root node. Remove them
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board dtb files unified, we now have a
duplicate vtt_pinmux node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board dtb files unified, we now have a
duplicate mdio node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
The pinmux for usb0 is missing from the Linux board dtb file. Remove it
until we can introduce it in Linux
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board dtb files unified, we now have a
duplicate ospi0 node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board dtb files unified, we now have a
duplicate wkup_i2c0 node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board dtb files unified, we now have a
duplicate sdhci1 pinmux node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board dtb files unified, we now have
a duplicate sdhci0 pinmux node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board dtb files unified, we now have a
duplicate main_uart0 node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board dtb files unified we now have a
duplicate mcu_uart0 node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Ethernet is one of a few IPs in U-Boot that depend on DMA to operate.
However there are a few missing registers ranges in the udmap nodes
need to properly setup DMA for the am65x.
A fix has been added to the Linux kernel[0] to add these ranges however
they have not made it to a Linux tag. To keep DMA operational until the
next DT sync from Linux, add these ranges to the *-u-boot.dtsi with a
note for our future selves.
[0] https://lore.kernel.org/r/20231213135138.929517-2-vigneshr@ti.com
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board dtb files unified, we now have a
duplicate mcu_udmap node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board dtb files unified, we now have a
duplicate mcu_ringacc node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
timer1 is really just the mcu_timer0 node redefined for the WKUP SPL.
Remove the timer1 and replace it with the mcu_timer0 from the Linux
device tree we imported into U-Boot.
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board files unified, we now have a duplicate
wkup_uart0 node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board dtb files unified we now have a
duplicate vtt_supply node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
To make things as organized as possible, start from the Linux board dtbs
and apply all properties needed for U-Boot in our *-u-boot.dtsi file for
the MAIN SPL and U-Boot builds.
We can then include these files for the WKUP SPL build making further
edits to the needed properties and nodes for the WKUP SPL bootloader's
view of the am65x.
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
In order to unify the R5 board dtb file with the Linux board dtb file,
we will need to copy all bootph-pre-ram properties to the *-u-boot.dtsi
overlay.
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Pull in dtb updates for the am654 base board from v6.7-rc1 of Linux
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
The R5 board file for U-Boot should be the same as the board file copied
from Linux with a few alterations to work with the R5's view of the SoC.
First we need to unify the R5 board file and it's U-Boot overlay before
we can unify the Linux board file with this one.
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
We do not have a need to share a single console with the evaluation
board and disabling this option reduces the complexity of configuring
the consoles. Disable CONSOLE_MUX
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Some of the regulators we need to successfully boot are fixed
regulators. Enable the driver to properly probe them.
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Apple machines do not have memory below 4G. Since U-Boot does
not support the SMBIOS 3 header structures this means we can't
support SMBIOS on these machines. Unfortunately the refactoring
of the SMBIOS code this cycle accidentally enabled it again.
Fixes: 53fab13a7b ("efi: Use the installed SMBIOS tables")
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Make DRAM stable on i.MX8MP DHCOM SoM by using FPWM mode and updating
the DRAM timing
- Fix display artifacts when booting Linux on i.MX8M Mini/Plus eDM SBC
Currently the wget command is hard wired to HTTP port 80. This is
inconvenient, as it is extremely easy to start trivial HTTP server
as an unprivileged user using e.g. python http module to serve the
files, but such a server has to run on one of the higher ports:
"
$ python3 -m http.server -d $(pwd) 8080
"
Make it possible to configure HTTP server port the same way it is
possible to configure TFTP server port, using environment variable
'httpdstp' (similar to 'tftpdstp'). Retain port 80 as the default
fallback port. This way, users can start their own trivial server
and conveniently download whatever files they need into U-Boot.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The current DDR subsystem configuration occasionally results in write failures,
impacting memory stability, on Verdin AM62 Solo 512MB WB IT 0072 SKU.
This commit addresses the issue by adjusting Drive Pull-Up/Down and
Write Latency to improve the eye diagram and ensure reliable write operations.
This configuration is shared with all Verdin AM62 SoM and
it does not introduce regressions.
Configurations changes from previous / default values:
- Drive Pull-Up/Down from 40 to 34.3 Ohm
- Write Latency from 8 to 10
- ODTLon / ODTLoff latency from 0 / 0 to 4 / 20 nCK
- VREF control range 1 at 27 %
- tFAW from 30 to 40 ns
Configuration is output from SysConfig [1] web tool, currently at version
1.18.1+3343 (DDR SubSystem v9.10).
[1] https://dev.ti.com/sysconfig
Fixes: 7d1a10659f ("board: toradex: add verdin am62 support")
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The contents of README.sha1 only refer to process around verification
of the pcs440ep board firmware in flash. The device was removed in
commit 242836a893 ("powerpc: ppc4xx: remove pcs440ep support") in
2015 so this readme isn't really relevant anymore so can be removed.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Turn display connector power off on boot and reboot to prevent any
bogus start up sequence of any panel potentially attached to the
display connector.
Signed-off-by: Marek Vasut <marex@denx.de>
Import DRAM timings generated by the DDR tool 3.31 which introduce assorted
tweaks to the DRAM controller settings. Furthermore, enable DBI to improve
noise resilience of the DRAM bus by reducing the number of bit changes on
the bus.
Reduce the DRAM rate to 3600 MTps to remove all remaining correctable errors
reported by EDAC . It is not entirely clear why the slightly faster setting
does produce sporadic correctable errors, while this one does not, but this
could be related to simpler PLL setting at 3600 MTps.
Enable inline ECC which is necessary to detect ECC errors and collect
statistics by the EDAC driver in Linux. This reduces the DRAM size by
64 MiB for each 512 MiB of DRAM, so for a 4 GiB device the available
DRAM size becomes 3.5 GiB and for 2 GiB device the available DRAM size
becomes 1.8 GiB.
Signed-off-by: Marek Vasut <marex@denx.de>
In case the Buck5 and Buck6 regulators which supply DRAM Vdd1 and Vdd2/Vddq
respectively operate in automatic PWM/PFM mode, the DRAM EDAC detects more
correctable errors than if the regulators operate in forced PWM only mode.
Force DRAM regulators to forced PWM mode only to stop tempting the DRAM.
Signed-off-by: Marek Vasut <marex@denx.de>
clock changes for u-boot/master
This has some clock fixes which should go in before the release. It's a bit
late in the cycle, but most of these have tests to go along with them.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
It's possible for composite clocks to have a divider that does not
implement set_rate() operation. For example, sandbox_clk_composite()
registers composite clock with a divider that only has get_rate().
Currently clk_composite_set_rate() only checks thate rate_ops are
present, so for sandbox it will cause NULL dereference during
clk_set_rate().
This patch adds rate_ops->set_rate check tp clk_composite_set_rate().
Signed-off-by: Igor Prusov <ivprusov@salutedevices.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20231205232334.2931-2-ivprusov@salutedevices.com
- Fix for i.MX8M Plus eDM SBC DDR timings with inline ECC
- Switch to FPWM mode on Data Modul i.MX8M Plus eDM SBC so that DRAM
EDAC detects more correctable errors
- Fix for imx8mp-venice board DDR initialization
The DRAM configuration for the 1GB and 4GB imx8mp venice boards had a
bus mapping issue (channel A and B swapped) which creates an invalid
deskewing configuration during training causing the DRAM to not be able
to run at its full bus speed.
Update the various config structures to resolve this.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Import DRAM timings generated by the DDR tool 3.31 which introduce assorted
tweaks to the DRAM controller settings. Furthermore, enable DBI to improve
noise resilience of the DRAM bus by reducing the number of bit changes on
the bus.
Reduce the DRAM rate to 3600 MTps to remove all remaining correctable errors
reported by EDAC . It is not entirely clear why the slightly faster setting
does produce sporadic correctable errors, while this one does not, but this
could be related to simpler PLL setting at 3600 MTps.
Enable inline ECC which is necessary to detect ECC errors and collect
statistics by the EDAC driver in Linux. This reduces the DRAM size by
64 MiB for each 512 MiB of DRAM, so for a 4 GiB device the available
DRAM size becomes 3.5 GiB .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
In case the Buck5 and Buck6 regulators which supply DRAM Vdd1 and Vdd2/Vddq
respectively operate in automatic PWM/PFM mode, the DRAM EDAC detects more
correctable errors than if the regulators operate in forced PWM only mode.
Force DRAM regulators to forced PWM mode only to stop tempting the DRAM.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Enable CAAM in U-Boot to make crypto available early in the boot process.
This has a side-effect that in case an older kernel version contains a
broken CAAM initialization timeout code, initialization in bootloader
will help that old kernel version function correctly.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Enable CAAM in U-Boot to make crypto available early in the boot process.
This has a side-effect that in case an older kernel version contains a
broken CAAM initialization timeout code, initialization in bootloader
will help that old kernel version function correctly.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add PLL settings for DDR 3600 MTps . This is very similar to 3200 MTps
PLL setting, except the divider is not 9 but 8 .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The new MX8M DDR tool 3.31 now generates a programming file which uses
data rate 3734 instead of 3733 or 3732 . Handle another rounding option .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Inhibit DTC warning in imx8mp-dhcom-pdk3-overlay-rev100.dts:
"
arch/arm/dts/imx8mp-dhcom-pdk3-overlay-rev100.dtbo: Warning (reg_format): /fragment@0/__overlay__:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
arch/arm/dts/imx8mp-dhcom-pdk3-overlay-rev100.dtbo: Warning (avoid_default_addr_size): /fragment@0/__overlay__: Relying on default #address-cells value
arch/arm/dts/imx8mp-dhcom-pdk3-overlay-rev100.dtbo: Warning (avoid_default_addr_size): /fragment@0/__overlay__: Relying on default #size-cells value
"
The DTO overwrites the 'reg' property of an ethernet PHY and is only
used on specific combination of old prototype SoM and old prototype
PDK3 carrier board, which had incorrectly placed pull resistor, which
made the PHY change its MDIO address in that specific combination and
which is already fixed on production hardware.
The DTO is implemented in this simple manner because if it contained a
full MDIO bus node reference to define #address-cells and #size-cells,
it would also require a full new copy of the PHY node, i.e.
ethernet-phy@5 { ... reg = <5>; ... }, to avoid DTC warnings about
mismatch between node unit and reg value. The node unit in SoM DT is
ethernet-phy@7 { ... }; .
This simpler approach avoids unnecessary duplication without adverse
side effects.
Reported-by: Fabio Estevam <festevam@denx.de>
Reported-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Tested-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Fixes a filepath in MAINTAINERS file that wasn't updated when
renaming the files to match the new SoC name.
Fixes: a4bd5e4120 ('arm: apple: Change SoC name from "m1" into "apple"')
Signed-off-by: Moritz Fischer <moritzf@google.com>
Both FS_LOADER and SPL_FS_LOADER have the same menu prompt.
To avoid confusion, make prompt for SPL_FS_LOADER different.
Signed-off-by: Alexander Gendin <agendin@matrox.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The correct symbol to enable to have SMBIOS populate fields based on the
device tree is SYSINFO_SMBIOS and not SMBIOS_SYSINFO.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Fix emmc detection on colibri_imx7
- Fix DDR configuration on tqma6 to improve Ethernet performance
- Fix aliases and chosen nodes indentation on imx7s-warp
- Convert pico-imx6ul to DM_SERIAL
- Convert pico-pi-imx7d to watchdog driver model to fix 'reset' command
- Select CONFIG_NET_RANDOM_ETHADDR on imx8mp_evk to fix networking on
older boards
- Add USBH_EN gpio hog to fix USB host interface not working on some
Apalis Toradex carrier boards with Apalis iMX8 SoM
- Add PCI fixup for GW73xx-F+
- Fix broken EEPROM read on imx8mn-var-som
Later versions of Colibri iMX7D V1.1B modules use a "new" SoC fusing. The
difference lies in whether we enable the boot ROM to use the eMMC reset
signal. Depending on the SoC fuse, the boot ROM configures this pin as a
GPIO output to drive the reset signal. Our eMMC vs NAND detection
currently only sets that signal to a GPIO without explicitly setting any
direction. Previously, by default, it was set as an input. As the boot ROM
now configures it as an output, we receive a value of zero instead of one,
indicating the absence of the pull-up on eMMC modules.
To fix this, set the SION bit, allowing the reading back of the value
even if it is configured as an output by the boot ROM. It's important to
note that with the new SoC fusing, we now read back what the boot ROM
drives rather than the real value caused by the pull-up resistor. However,
if it were ever driven low, the eMMC would permanently be reset.
In addition, remove hard-coded variant in the eMMC build case as since the
commit 0c39564d02 ("toradex: colibri_imx7: Enable nand/emmc detection
and set boot variant") will anyways always get overridden by the detection
routing in board code.
Fixes: 0c39564d ("toradex: colibri_imx7: Enable nand/emmc detection and set boot variant")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Hiago De Franco <hiago.franco@toradex.com>
Initially investigating a Linux network issue causing a lot of drop and
poor network performances on a custom system based on a TQMA6A module
(based on an iMX6Q), [1st link below].
I eventually correlated my observations with a contention at the NIC
level when in concurrency with the graphics pipeline. Troubleshooting
this in the kernel lead to disabling DMA bursts accesses made by the IPU
in order to avoid triggering the QoS at the interconnect level, reducing
from 50 to 10% the drop rate on eth0, [2nd link below]. The solution
worked on my setup but not on others, which still suffered from
abnormally high drop rates even with this "fix".
After looking a while into TQ Systems BSP I figured out a number of
differences in recent U-Boot out-of-tree patches they had in their
repository [3rd link]. Parsing the differences one after the other lead
me to this final solution.
The reset pad of the DDR controller was apparently misconfigured, Bit
18-19 picturing the "DDR select field". The current value b11 is
reserved. The only defined value as of version 6 of the iMX6Q manual was
b00 "DDR3 and LPDDR2 mode". In practice no register difference has been
spotted after changing this configuration but all issues tracked thus
far just vanished. All previous fixes have been proven irrelevant. Just
clearing this field solved all our network issues and the drop rate as
measured by iperf3 felt back to 0%.
Link: https://lore.kernel.org/netdev/20231012193410.3d1812cf@xps-13/
Link: https://lists.freedesktop.org/archives/dri-devel/2023-October/428251.html
Link: 15eb6abbef
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The aliases and chosen nodes are currently indented using spaces.
Fix them to use the standard tab indentation.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Commit 68dcbdd594 ("ARM: imx: Add weak default reset_cpu()") caused
the 'reset' command in U-Boot to not cause a board reset.
Fix it by switching to the watchdog driver model via sysreset, which
is the preferred method for implementing the watchdog reset
Signed-off-by: Fabio Estevam <festevam@denx.de>
On an early revision of the imx8mp-evk that I have access to,
the MAC addresses fuses are not programmed, causing failure to bring
the Ethernet interfaces.
Fix this problema by selecting CONFIG_NET_RANDOM_ETHADDR so that
random MAC addresses are assigned and the Ethernet ports become
functional out of the box.
Signed-off-by: Fabio Estevam <festevam@denx.de>
USB host interface is not working on some Apalis Toradex carrier
boards with Apalis iMX8 SoM. This is due to USBH_EN pin, which
powers USB peripherals, having a strong pull-down on some boards,
and a weak pull-down on the others. This USBH_EN pin is left
unconfigured, which means it is in its default state at cold boot:
input with a strong pull-up. As a result, carrier boards with a
weak pull-down have this signal high enough to trigger power
delivery to USB peripherals, and opposite - boards with strong
pull-down on USBH_EN have this signal below the threshold needed
to trigger USB power delivery.
This change configures the USBH_EN pin as gpio hog, fixing this
issue for all Apalis carrier boards regardless of pull-down
resistor value.
Also, update apalis-imx8_defconfig via savedefconfig.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
GW73xx-F board revision switched back to the original PCIe switch due to
part availability.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
On branch WIP/17Oct2023, the EEPROM can no longer be read:
U-Boot 2023.10-latest (Oct 17 2023 - 15:53:43 -0400)
CPU: Freescale i.MX8MNano Quad rev1.0 at 1200 MHz
Reset cause: POR
Model: Variscite VAR-SOM-MX8MN Symphony evaluation board
var_read_som_eeprom: uclass_get_device_by_of_offset() failed: -19
initcall failed at call 000000004022207c (err=-19)
Convert EEPROM-related properties to bootph-all so that the EEPROM can
also be read outside of SPL.
Fixes: 9e644284ab ("dm: core: Report bootph-pre-ram/sram node as pre-reloc after relocation")
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Recently pylint has started to complain about:
No name 'fs_helper' in module 'tests' (no-name-in-module)
Due to:
from tests import fs_helper
However, we have:
test/py/tests/fs_helper.py
And since we do not want to add a dummy test/py/tests/__init__.py to
silence this warning we instead just disable it as needed.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
- StarFive: Add StarFive watchdog driver
- VisionFive2: Support device tree overlay for VisionFive2 board
- Andes: Fix PLIC-SW setting
- RISC-V: Fix NVMe support by implying NVME_PCI for QEMU
- RISC-V: Fix binman for 64 bit format load address
To quote the author:
Currently bootmeth_efi crashes while doing a network (dhcp) boot.
This patch series fixes issues and both network and disk boot works.
# Do not modify or remove the line above.
# Everything below it will be ignored.
#
# Please enter a commit message to explain why this merge is necessary,
# especially if it merges an updated upstream into a topic branch.
#
# An empty message aborts the commit.
bootmeth_efi doesn't allocate any buffer to load efi in any case.
enable static buffer flag for all cases.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Shantur Rathore <i@shantur.com>
While booting with efi, if fdt isn't available externally,
just use the built-in one.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Shantur Rathore <i@shantur.com>
We need to set boot->fname before calling efi_set_bootdev
otherwise this crashes as bflow->fname is null.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Shantur Rathore <i@shantur.com>
bootmeth_efi sets up bootp_arch which is read later in bootp.c
Currently bootp_arch is being set as integer string and being
read in bootp.c as hex, this sends incorrect arch value to dhcp server
which in return sends wrong file for network boot.
For ARM64 UEFI Arch value is 0xb (11), here we set environment as 11
and later is read as 0x11 and 17 is sent to dhcp server.
Setting it as hex string fixes the problem.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Shantur Rathore <i@shantur.com>
The memory maps for Apple's M2 Pro/Max/Ultra left MMIO space out which
was not used by any driver at the time. The display out exposed as
simple-framebuffer use a power-domain controlled by a device in an
unmapped region.
Add a map covering this region as well as another MMIO region in the
range 0x4'0000'0000 - 0x5'0000'0000. The added regions cover all MMIO
annotated in Apple's device tree in this range.
Signed-off-by: Janne Grunau <j@jannau.net>
Reviewed-by: Eric Curtin <ecurtin@redhat.com>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
The first four patches are actual fixes. The last three patches add
support for the apparently popular OrangePi Zero 3 board: multiple
people seem to be champing at the bit, so I'd rather give them
something real instead of people using random trees they found on the
Internet. It's actually mostly the new defconfig file anyway, so the
chances for regressions are very slim.
Pull request efi-2024-01-rc5
Documentation:
* Update and correct support notes on clang
* sandbox: Fix VPL instructions
UEFI:
* Fix a bug in DisconnectController
* Provide better error messages for missing CONFIG_EFI_CAPSULE_ESL_FILE
* Create EFI memory reservations when booting via ACPI
* Make ACPI tables accessible in EFI app
The OrangePi Zero 3 is a small development board featuring the Allwinner
H618 SoC, shipping with up to 4GB of DRAM, Gigabit Ethernet, a micro-HDMI
connector and two USB sockets.
The board uses LPDDR4 DRAM and an X-Powers AXP313a PMIC, support for
which was recently added to U-Boot.
Add a defconfig file selecting the right drivers and DRAM options.
Since the .dts file was synced from the Linux kernel repo already, we
just need to add one line to the Makefile to actually build the .dtb.
The DRAM parameters were derived from the values found in the BSP DRAM
drivers on the SPI NOR flash.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mikhail Kalashnikov <iuncuim@gmail.com>
Tested-by: Bob McChesney <bob@electricworry.net>
Tested-by: Stephen Graf <stephen.graf@gmail.com>
The original H616 devices released about three years ago were typically
paired with an X-Powers AXP305 PMIC. Newer devices uses the smaller
AXP313, and there seem to be far more systems with this PMIC around now.
Remove the default AXP305 selection for the H616 SoC from the Kconfig,
and move the PMIC selection into the board defconfig files instead.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add support for the zBIT ZB25VQ128 (128M-bit) SPI NOR flash memory chip,
as used on the Xunlong Orange Pi Zero 3 board.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
The current emac setting is not suitable for Orange Pi Zero 3,
move it back to Orange Pi Zero 2 DT. Also update phy mode and
delay values for emac on Orange Pi Zero 3.
With these changes, Ethernet now looks stable.
Fixes: 95c3b0635e ("sunxi: dts: arm64: update devicetree files from Linux-v6.6-rc6")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The mtd_debug write does not work in this context. The flashcp command does
work, provides both the erase and write functions and with the verbose
option gives good feedback.
Signed-off-by: Stephen Graf <stephen.graf@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
When using the USB OTG FEL mode on the Allwinner H616, the BootROM
stores some data at the end of SRAM C. This is also the location where
we place the initial SPL stack, so it will overwrite this data.
We still need the BROM code after running the SPL, so should leave that
area alone.
Interestingly this does not seem to have an adverse effect, I guess on
the "way out" (when we return to FEL after the SPL has run), this data
is not needed by the BROM, for just the trailing end of the USB operation.
However this is still wrong, and we should not clobber BROM data.
Lower the SPL stack address to be situated right below the swap buffers
we use in sunxi-fel: that should be out of the way of everyone else.
This obsoletes a previous commit (eb53e7743c) with the same name:
that one was changing the address in an *unused* macro in sunxi_common.h,
so the previous patch didn't have any effect at all.
Fixes: eb53e7743c ("sunxi: h616: lower SPL stack address to avoid BROM data")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The OrangePi Zero 2 has a USB VBUS regulator, controlled by pin PC16.
This is correctly described in the DT, but the patches for supporting
this are still pending.
Meanwhile add our good old CONFIG_USB1_VBUS_PIN to the defconfig file,
to enable power on the USB port and allow using a USB flash drive, for
instance.
Fixes: 6acc5fa581 ("sunxi: H616: enable USB support for H616 boards")
Reported-by: Mikhail Kalashnikov <iuncuim@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
device tree overlay support requires fdtoverlay_addr_r to be set
before
~~~~~~
Invalid fdtoverlay_addr_r for loading overlays
after
~~~~~
Retrieving file: /boot/overlay/rtc-ds3231.dtbo
Signed-off-by: John Clark <inindev@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
On 32-core platform, hart31 gets stuck at secondary_hart_loop
as the corresponding enable bit is not set in enable_ipi().
We should program the next word (0x2f84) which is assigned
as the enable register of hart31. It should be done in the same
way when we invoke riscv_send_ipi() to trigger software interrupt
on hart31.
The following diagram shows the enable bits of the fixed PLICSW
scheme.
Pending regs: 0x1000 x---0---0---0---0------0---0
Pending hart ID: 0 1 2 3 ... 30 31
Interrupt ID: 0 1 2 3 4 ... 31 32
| | | | | | |
Enable regs: 0x2000 x---1---0---0---0-...--0---0---> hart0
| | | | | | |
0x2080 x---0---1---0---0-...--0---0---> hart1
| | | | | | |
0x2100 x---0---0---1---0-...--0---0---> hart2
| | | | | | |
0x2180 x---0---0---0---1-...--0---0---> hart3
. . . . . . .
. . . . . . .
. . . . . . .
0x2f00 x---0---0---0---0-...--1---0---> hart30
| | | | | | |
0x2f80 x---0---0---0---0-...--0---1---> hart31
<-------- word 0 -------><--- word 1 --->
This patch includes some cleanups to macros/functions.
Fixes: ebf11273220a ("riscv: andes: Rearrange Andes PLICSW to single-bit-per-hart strategy")
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Randolph <randolph@andestech.com>
CONFIG_NVME=y without CONFIG_NVME_PCI=y does not provide working NVMe
support. Instead of implying CONFIG_NVME we must imply CONFIG_NVME_PCI
which will select CONFIG_NVME.
Fixes: e64db0d92e ("riscv: qemu: Enable e1000 and nvme support")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Add to support StarFive watchdog driver. The driver is imported from
linux kernel's drivers/watchdog/starfive-wdt.c without jh7100 support
because there is no support of jh7100 SoC in u-boot yet.
Howver, this patch has been kept the variant coding style because JH7100
can be added later and have a consistency with the linux driver.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add JH7110_SYSCLK_WDT_APB and JH7110_SYSCLK_WDT_CORE clocks for JH7110
watchdog device.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
commit 239d59a65e ("efi_loader: reconnect drivers on failure")
tried to fix the UninstallProtocol interface which must reconnect
any controllers it disconnected by calling ConnectController()
in case of failure. However, the reconnect functionality was wired in
efi_disconnect_all_drivers() instead of efi_uninstall_protocol().
As a result some SCT tests started failing.
Specifically, BBTestOpenProtocolInterfaceTest333CheckPoint3() test
- Calls ConnectController for DriverImageHandle1
- Calls DisconnectController for DriverImageHandle1 which will
disconnect everything apart from TestProtocol4. That will remain
open on purpose.
- Calls ConnectController for DriverImageHandle2. TestProtocol4
which was explicitly preserved was installed wth BY_DRIVER attributes.
The new protocol will call DisconnectController since its attributes
are BY_DRIVER|EXCLUSIVE, but TestProtocol4 will not be removed. The
test expects EFI_ACCESS_DENIED which works fine.
The problem is that DisconnectController, will eventually call
EFI_DRIVER_BINDING_PROTOCOL.Stop(). But on the aforementioned test
this will call CloseProtocol -- the binding protocol is defined in
'DBindingDriver3.c' and the .Stop function uses CloseProtocol.
If that close protocol call fails with EFI_NOT_FOUND, the current code
will try to mistakenly reconnect all drivers and the subsequent tests
that rely on the device being disconnected will fail.
Move the reconnection in efi_uninstall_protocol() were it belongs.
Fixes: commit 239d59a65e ("efi_loader: reconnect drivers on failure")
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
ACPI tables cannot convey memory reservations for ARM and RISC-V.
x86 uses the BIOS E820 table for this purpose. We cannot simply ignore the
device-tree when booting via ACPI. We have to assign EfiReservedMemory
according to the prior stage device-tree ($fdtaddr) or as fallback the
control device-tree ($fdtcontroladdr).
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The current build system embeds the EFI Signature List(ESL)
into the dtb to be used in the EFI capsule authentication.
This ESL file is specified through the CONFIG_EFI_CAPSULE_ESL_FILE
Kconfig option. If CONFIG_EFI_CAPSULE_ESL_FILE is not specified,
U-boot build ends up with failure but the cause of failure is not
easily understandable. Current error message is as follows.
FATAL ERROR: Error reading file into data: Is a directoryCheck /home/ubuntu/src/ledge/u-boot/arch/arm/dts/.synquacer-sc2a11-developerbox.dtb.pre.tmp for errors
make[2]: *** [scripts/Makefile.lib:355: arch/arm/dts/synquacer-sc2a11-developerbox.dtb] Error 1
make[1]: *** [dts/Makefile:44: arch-dtbs] Error 2
make: *** [Makefile:1165: dts/dt.dtb] Error 2
make: *** Waiting for unfinished jobs....
This commit shows the error message that CONFIG_EFI_CAPSULE_ESL_FILE
must be specified when the EFI capsule authentication is enabled, then
terminate the build with error.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Weizhao Ouyang <o451686892@gmail.com>
At this point, clang can be used on both 32bit and 64bit targets without
issue. Make note of logic we have that will inform clang of the
architecture to build for.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Fix the devicetree used with sandbox. This is needed because the
default (full) devicetree must be used by all phases of boot, with
sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The wdt_start function takes timeout_ms as a parameter and starts the
watchdog with this value. However, when you output the message, it shows
the default timeout value for the watchdog device.
So this patch fixes that part to output the correct timeout value.
Before -->
StarFive # wdt start 3000
WDT: Started watchdog@13070000 without servicing (60s timeout)
After -->
StarFive # wdt start 3000
WDT: Started watchdog@13070000 without servicing (3s timeout)
Fixes: c2fd0ca1a8 ("watchdog: Integrate watchdog triggering into the cyclic framework")
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Stefan Roese <sr@denx.de>
As requirement of CR side, QSPI Flash usage via RPC driver shall
be disabled and leaving the control of this module to CR side.
Perform DT modification to disable the RPC SPI.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Cong Dang <cong.dang.xn@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Do not modify defconfig, modify the DT instead, this way
the RPC SPI can be enabled without recompiling the U-Boot
itself. Update commit message accordingly.]
Use the phandle reference to &rpc node in arch/arm/dts/r8a779g0.dtsi
and remove properties which are already in arch/arm/dts/r8a779g0.dtsi.
No functional change and no resulting DT change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Compiling with CONFIG_USB_XHCI_PCI and CONFIG_PCI=n results in
usb/host/xhci-pci.c:48:(.text.xhci_pci_probe+0x44):
undefined reference to `dm_pci_write_config32
Add the missing Kconfig dependency.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Like Rockchip RK3328 and RK3568, the RK3588 also have a single node to
represent the glue and ctrl for USB 3.0.
Use rk_ops as driver data to select correct ctrl node for RK3588 DWC3.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Marek Vasut <marex@denx.de>
USB UFI uses fixed 12-byte commands (as does RBC, which is not
supported), but SCSI does not have this limitation. Use the correct
command block lengths depending on the subclass.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Marek Vasut <marex@denx.de>
Some devices like YubiKeys need more time before SET_ADDRESS. The spec
says we need to wait 10ms.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Marek Vasut <marex@denx.de>
We need to get the DMA address before incrementing the pointer, as that
might move us onto another segment.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Marek Vasut <marex@denx.de>
Now that we always check the return value, just return NULL on timeouts.
We can still log the error since this is a problem, but it's not reason
to panic.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Marek Vasut <marex@denx.de>
This isn't going to work, don't pretend it will and then end up timing
out.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Marek Vasut <marex@denx.de>
There is currently no codepath to recover from this case. In principle
we could require that the upper layer do this explicitly, but let's just
do it in xHCI when the next bulk transfer is started, since that
reasonably implies whatever caused the problem has been dealt with.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Marek Vasut <marex@denx.de>
There is a race where an endpoint may halt by itself while we are trying
to halt it, which results in a context state error. See xHCI 4.6.9 which
mentions this case.
This also avoids BUGging when we attempt to stop an endpoint which was
already stopped to begin with, which is probably a bug elsewhere but
not a good reason to crash.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Marek Vasut <marex@denx.de>
If the xHC has a problem with our STOP ENDPOINT command, it is likely to
return a completion directly instead of first a transfer event for the
in-progress transfer. Handle that more gracefully.
We still BUG() on the error code, but at least we don't end up timing
out on the event and ending up with unexpected event errors.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Marek Vasut <marex@denx.de>
xhci_wait_for_event returns NULL on timeout, so the caller always has to
check for that. This addresses immediate explosions in this part
of the code when timeouts happen, but not the root cause for the
timeout.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Marek Vasut <marex@denx.de>
Update maintainers for Tegra SoC platform. Include device trees
and drivers which contain tegra in the name.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
The "i2cbcdev" sneaked in when implementing this function for the
bootcounter use case. Obviously the intention was to use prop_name
instead.
Fixes: b483552773 (i2c: Implement i2c_get_chip_by_phandle())
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
As correct default SYS_CONFIG_NAME value is now set in
board/samsung/axy17lte/Kconfig (in commit "board: samsung: Fix
SYS_CONFIG_NAME configs in axy17lte Kconfig"), the SYS_CONFIG_NAME
option can be safely removed from all a*y17lte defconfigs. That removal
doesn't change resulting .config files.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
There is a couple of issues related to SYS_CONFIG_NAME config in
axy17lte Kconfig.
1. The global SYS_CONFIG_NAME in axy17lte Kconfig overrides
SYS_CONFIG_NAME for all boards specified after this line in
arch/arm/mach-exynos/Kconfig:
source "board/samsung/axy17lte/Kconfig"
Right now it's the last 'source' line there, so the issue is not
reproducible. But once some board is moved or added after this line
the next build error will happen:
GEN include/autoconf.mk.dep
In file included from ./include/common.h:16:
include/config.h:3:10: fatal error: configs/exynos78x0-common.h.h:
No such file or directory
3 | #include <configs/exynos78x0-common.h.h>
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
compilation terminated.
That's happening because axy17lte Kconfig defines SYS_CONFIG_NAME
option in global namespace (not guarded with any "if TARGET_..."), so
it basically rewrites the correct SYS_CONFIG_NAME defined in the
hypothetical boards which might appear after axy17lte in mach-exynos
Kconfig.
2. Another side of the issue is that SYS_CONFIG_NAME is defined
incorrectly in axy17lte Kconfig:
config SYS_CONFIG_NAME
default "exynos78x0-common.h"
The .h extension should not have been specified there. It's leading
to a build error, as the generated include file has a double '.h'
extension.
3. Each target in axy17lte/Kconfig defines its own SYS_CONFIG_NAME. But
all of those in fact incorrect, as corresponding
include/configs/<CONFIG_SYS_CONFIG_NAME>.h header files don't exist.
4. The global SYS_CONFIG_NAME pretty much repeats the help description
from arch/Kconfig and doc/README.kconfig.
Corresponding defconfig files (a*y17lte_defconfig) fix above issues by
overriding SYS_CONFIG_NAME and correctly setting it to
"exynos78x0-common".
Fix all mentioned issues by removing the incorrect global
SYS_CONFIG_NAME and instead specifying it (correctly) in SYS_CONFIG_NAME
options for each target instead.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Fixes: 3e2095e960 ("board: samsung: add support for Galaxy A series of 2017 (a5y17lte)")
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
As the address read from device tree is being cast to a pointer, it's
better to use dev_read_addr_ptr() API for getting that address. The more
detailed explanation can be found in commit a12a73b664 ("drivers: use
dev_read_addr_ptr when cast to pointer").
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Get rid of magic numbers in s5p_serial_init() when writing to UART
registers. While at it, use BIT() macro for existing constants when
appropriate.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Use dev_read_u8_default() instead of fdtdec_get_int() to read the "id"
property from device tree, as suggested in [1]. dev_* API is already
used in this driver, so there is no reason to stick to fdtdec_* API.
This also fixes checkpatch warning:
WARNING: Use the livetree API (dev_read_...)
[1] doc/develop/driver-model/livetree.rst
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Pull request efi-2024-01-rc4
Documentation
* Add HiSilicon board documentation to HTML docs
* Fix building with Sphinx 6.0
UEFI
* Increase default variable store size to 128K
* Check return value of efi_append_scrtm version
* Create shortened boot options in eficonfig command
Other
* Avoid incorrect error message in mkimage
The ChipIdea device controller wasn't properly cleaned up when disabled.
So enabling it again left it in a broken state. The problem occurred for
example when the host unbinds the driver and binds it again.
During the first setup, when the out request is queued, the endpoint is
primed (`epprime`). If the endpoint is then disabled, it stayed primed
with the initial buffer. So after the endpoint is re-enabled, the device
controller and device driver were out of sync: the new out request was
in the driver queue head, yet not submitted, but the "complete" function
was still called, since the endpoint was primed with the old buffer.
With the fastboot function this error led to the (rather confusing)
error message "buffer overflow".
Fixed by clearing the primed buffers with the `epflush` (`ENDPTFLUSH`)
register.
Signed-off-by: Simon Holesch <simon@holesch.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20231120002024.32865-1-simon@holesch.de
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
The boot options created by eficonfig should use shortened device-paths to
avoid problems if drives are enumerated in a different sequence.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
It is unclear to developers why efi_var_from_file() returns EFI_SUCCESS if
file ubootefi.var is missing or corrupted. Improve the description.
Reported-by: Weizhao Ouyang <o451686892@gmail.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Weizhao Ouyang <o451686892@gmail.com>
The result of efi_append_scrtm_version() is overwritten before anyone
checks its result. Check it and exit the function on failures
Addresses-Coverity-ID: 467399 Code maintainability issues (UNUSED_VALUE)
Fixes: commit 97707f12fd ("tpm: Support boot measurements")
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
In commit 9fd3f881c6 ("efi_loader: Increase default variable store size to 64KiB")
Alper has a detailed explanation of why the size needs to be bumped to at
least 64K. However enabling Secure boot, writing db, KEK, PK etc keys
will further increase the size so bump it to 128K.
It's worth noting that when U-Boot stores the EFI variables in an RPMB the
available storage is defined statically in StandAloneMM at build time.
The U-Boot code is detecting the available true size on the fly during
writes. When StandAloneMM is present this size defines the reserved
memory U-Boot can use to copy any runtime variables, before booting an
OS.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Sphinx 6.0 removed the execfile_() function, which we use as part of the
configuration process. They *did* warn us... Just open-code the
functionality as is done in Sphinx itself.
Tested (using SPHINX_CONF, since this code is only executed with an
alternative config file) on various Sphinx versions from 2.5 through 6.0.
Reported-by: Martin Liška <mliska@suse.cz>
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Rebased for U-Boot
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Add the README files for the HiSilicon boards to the HTML documentation.
This required a bit of reformatting.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
When running 'mkimage -l' is called for a valid StarFive file an error
message "Error: invalid marker bytes" is written by the Renesas SPKG
driver.
mkimage -l may be invoked without specifying an image type. In this case
mkimage iterates over all image type drivers to find the one that matches.
None of the non-matching drivers should write an error message.
Fix the Renesas SPKG driver.
Fixes: afdfcb11f9 ("tools: spkgimage: add Renesas SPKG format")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
SCSI device scan code was executing TEST UNIT READY command without
explicitly setting dma direction in struct scsi_cmd to NONE, so command
was passed to driver with dma direction set to DMA_FROM_DEVICE,
inherited from older usage.
With WDC SDINDDH6-64G ufs device, that caused TEST UNIT READY to
return error.
Fix that, by explicitly setting dma direction to NONE for
TEST UNIT READY, and restoring it back DMA_FROM_DEVICE for the
following READ CAPACITY.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Marek Vasut <marex@denx.de>
EFI applications can be very large and thus used to cause boot failures
when malloc() space was exhausted.
A recent changed fixed this by using the kernel_addr_r environment var
as the address of the buffer. However, it still frees the buffer when
the bootflow is discarded.
Fix this by introducing a flag to indicate whether the buffer was
allocated, or not.
Note that kernel_addr_r is not the last word here. It might be better
to use lmb to place images. But there is a lot of refactoring to do
before we can remove the environment variables. The distro scripts rely
on them so it is safe for bootstd to do so too.
Fixes: 6a8c2f9781 bootstd: Avoid allocating memory for the EFI file
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported by: Simon Glass <sjg@chromium.org>
Reported by: Shantur Rathore <i@shantur.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Shantur Rathore <i@shantur.com>
This reverts commit 6cdf6b7a34. This is
part of a series trying to make use of the arm64 hardware features for
tracking dirty pages. Unfortunately this series causes problems for the
AC5/AC5X SoCs. Having exhausted other options the consensus seems to be
reverting this series is the best course of action.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
This reverts commit 836b8d4b20. This is
part of a series trying to make use of the arm64 hardware features for
tracking dirty pages. Unfortunately this series causes problems for the
AC5/AC5X SoCs. Having exhausted other options the consensus seems to be
reverting this series is the best course of action.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
This reverts commit c1da6fdb5c. This is
part of a series trying to make use of the arm64 hardware features for
tracking dirty pages. Unfortunately this series causes problems for the
AC5/AC5X SoCs. Having exhausted other options the consensus seems to be
reverting this series is the best course of action.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
This fixes a regression in the eMMC fast boot mode case where the buffer
was missing 464 bytes.
The code figures out how many bytes must at least be fetched to honor
the current read, rounds that up to the ss->pagesize [which is a no-op
in the USB download case because that has ->pagesize==1], fetches that
many bytes, but then recorded the original upper bound as the new end of
the valid data. However, this did not take into account the rounding up
to the ss->pagesize. Fix this by recording the actual bytes downloaded.
Fixes: 4b4472438f ("imx: spl_imx_romapi: avoid tricky use of spl_load_simple_fit() to get full FIT size")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This config option enables the malloc() pool in TPL not the SPL. Fix
the description to accurately reflect this.
Fixes: fd8497dae5 (spl: Create proper symbols for enabling the malloc() pool)
Signed-off-by: John Keeping <jkeeping@inmusicbrands.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
According to the virtio v1.x "entropy device" specification, a virtio-rng
device is supposed to always return at least one byte of entropy.
However the virtio v0.9 spec does not mention such a requirement.
The Arm Fixed Virtual Platform (FVP) implementation of virtio-rng always
returns 8 bytes less of entropy than requested. If 8 bytes or less are
requested, it will return 0 bytes.
This behaviour makes U-Boot's virtio_rng_read() implementation go into an
endless loop, hanging the system.
Work around this problem by always requesting 8 bytes more than needed,
but only if a previous call to virtqueue_get_buf() returned 0 bytes.
This should never trigger on a v1.x spec compliant implementation, but
fixes the hang on the Arm FVP.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reported-by: Peter Hoyes <peter.hoyes@arm.com>
Correct this typo in the warning message shown when no more bootstage
records can be added.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
After opening pathname, we must close ifd once we are done with it.
Fixes: b9274095c2 ("sandbox: Add a way to map a file into memory")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
CONFIG_DM_WARN has a text indicating that these messages should only
provided when debugging. This implies that the setting must be default no.
We should still create debug messages.
Reported-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The importlib_resources import is not actually used. Fix this so that
patman can run on Python 3.6 to some extent, once
'pip3 install importlib-resources' has been run.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this code into a separate cmdline module, as is done with the
other tools.
Use the same HAS_TESTS check as buildman
Signed-off-by: Simon Glass <sjg@chromium.org>
Return an error when the user does not select an OS, so we know whether
to boot or not.
Move calling of bootflow_menu_run() into a separate function so we can
call it from other places.
Expand the test to cover these cases.
Add some documentation also, while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Adjust scan_mmc4_bootdev() and related function so that the caller can
do its own 'bootflow scan' command. This allows it to change the flags
if needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
The efi_gop driver uses private fields from the video uclass to obtain a
pointer to the frame buffer. Use the platform data instead.
Check the VIDEO_COPY setting to determine which frame buffer to use. Once
the next stage is running (and making use of U-Boot's EFI boot services)
U-Boot does not handle copying from priv->fb to the hardware framebuffer,
so we must allow EFI to write directly to the hardware framebuffer.
We could provide a function to read this, but it seems better to just
document how it works. The original change ignored an explicit comment
in the video.h file ("Things that are private to the uclass: don't use
these in the driver") which is why this was missed when the VIDEO_COPY
feature was added.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: 8f661a5b66 ("efi_loader: gop: Expose fb when 32bpp")
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The clk-pll.h is going to be included in multiple files soon. Add
missing header guard to prevent possible build errors in future.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Fixes: 166097e877 ("clk: exynos: add clock driver for Exynos7420 Soc")
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
clk_get_by_index() returns negative number on error. Assigning it to
unsigned int makes the subsequent "ret < 0" check always false, leading
in turn to possible unhandled errors. Change 'ret' variable type to
signed int so the code checks and handles clk_get_by_index() return code
properly.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Fixes: cf75cdf96e ("serial: s5p: use clock api to get clock rate")
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The sysreset uclass unconditionally provides a definition of the
reset_cpu() function. So does the exynos soc code. Fix the build with
SYSRESET enabled by omitting the function from the soc code in that
case. The code still needs to be kept around for use in SPL.
This commit was inspired by commit 6e19dc84c1 ("sunxi: Avoid duplicate
reset_cpu with SYSRESET enabled").
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
s5p watchdog driver calls samsung_get_base_watchdog() function, but its
prototype is not included. That might lead to build warnings like this:
drivers/watchdog/s5p_wdt.c: In function 'wdt_stop':
drivers/watchdog/s5p_wdt.c:16:26:
warning: implicit declaration of function
'samsung_get_base_watchdog' [-Wimplicit-function-declaration]
16 | (struct s5p_watchdog *)samsung_get_base_watchdog();
| ^~~~~~~~~~~~~~~~~~~~~~~~~
Include asm/arch/cpu.h to fix that issue.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
arch/arm/include/asm/arch/gpio.h relies on definitions from cpu.h.
Include it explicitly in gpio.h. Otherwise next build error may occur:
In file included from ./arch/arm/include/asm/gpio.h:7,
from include/cros_ec.h:14,
from board/samsung/common/board.c:8:
./arch/arm/include/asm/arch/gpio.h:1357:4:
error: 'EXYNOS4_GPIO_PART1_BASE' undeclared here
(not in a function); did you mean 'EXYNOS4_GPIO_MAX_PORT'?
1357 | { EXYNOS4_GPIO_PART1_BASE, EXYNOS4_GPIO_MAX_PORT_PART_1 },
| ^~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
samsung_get_base_swreset() is called in soc.c, but corresponding header
with its prototype is not included. Fix this to avoid possible build
errors.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Currently the renesas_sdhi_reset_tuning() unconditionally leaves SDHI
clock enabled after the tuning reset. This is not always necessary.
After the driver performed tuning reset at the end of probe function,
or in the unlikely case that tuning failed during regular operation,
the SDHI clock can be disabled after the tuning reset. The following
set_ios call would reconfigure the clock as needed.
In case of regular set_ios call which requires a tuning reset, keep
the clock enabled or disabled according to the mmc->clk_disable state.
With this in place, the controllers which have not been accessed via
block subsystem after boot are left in quiescent state. However, if an
MMC device is used e.g. for environment storage, that controller would
be accessed during the environment load and left active, including its
clock which would still be generated. This is due to the design of the
MMC subsystem, which does not deinit a controller after it was started
once, the controller is only deinited in case of mmc rescan, or before
OS boot.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Tested-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Thuan Nguyen Hong <thuan.nguyen-hong@banvien.com.vn>
To quote Andre:
The first few patches are some easy refactorings and fixes, most of them
actually don't change the generated binaries at all. Then there is a
defconfig for a new board, for which we just gained the .dts file from
the last kernel DT sync.
On top there is support for a new PMIC (AXP313), and LPDDR4 support for
the Allwinner H616 SoC, both of which are needed to support new devices
that appeared lately, especially cheap TV boxes.
While those are technically new features, they don't affect existing
boards, for instance the LPDDR4 support code is guarded by a new DRAM
type Kconfig variable. So the risk for regressions is very slim.
Gitlab CI passed, and I booted that briefly on some boards, including an
H616 and an H618 one (with LPDDR4).
The H616 SoC family has support for several types of DRAM: DDR3,
LPDDR3, DDR4 and LPDDR4.
At the moment, the driver only supports DDR3 and LPDDR3 memory.
Let's extend the driver to support the LPDDR4 memory. This type
of memory widely used in device with T507(-H) SoC and new orangepi
zero3 with H618.
The compatibility with T507 is not yet complete, because there
is difference in the phy_init array.
The LPDDR4-2133 timings correspond to DRAM Rayson RS1G32LO4D2BDS-53BT
found on the NOR SPI from the Orangepi Zero 3 4GB.
Signed-off-by: Mikhail Kalashnikov <iuncuim@gmail.com>
Tested-by: Piotr Oniszczuk <piotr.oniszczuk@gmail.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Andre Przywara <andre.przywara@arm.com>
The original H616 DDR3 ODT configuration code wrote board specific values
into a sequence of paired registers.
For LPDDR3 support we needed to special-case one group of registers,
because for that DRAM type we need to write 0 into the lower register of
each pair. That already made the code less readable.
LPDDR4 support will make things even messier, so let's refactor that
code now: We allow to write different values into the lower and upper
half of each pair. The masking is moved into a macro, and use in each
write statement.
The effect is not as obvious yet, as we don't need the full flexibility at
the moment, but the motivation will become clearer with LPDDR4 support.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Mikhail Kalashnikov <iuncuim@gmail.com>
The X-Powers AXP313a is a small PMIC with just three buck converters and
three LDOs, one of which is actually fixed (so not modelled here).
Add the compatible string and the respective regulator ranges to allow
drivers to adjust voltages.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
On boards using the AXP313 PMIC, the DRAM rail is often not setup
correctly at reset time, so we have to program the PMIC very early in
the SPL, before running the DRAM initialisation.
Add a simple AXP313 PMIC driver that knows about DCDC2(CPU) and
DCDC3(DRAM), so that we can bump up the voltage before the DRAM init.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
sunxi platforms put .bss in DRAM, so .bss is not available in SPL before
DRAM controller initialization. Therefore, this buffer must be placed in
the .data section.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
CONFIG_ARCH_SUNXI will not be enabled for RISC-V SoCs using this driver.
Use the symbol for the driver itself instead.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
The MMC controller driver is (and ought to be) the only user of these
register definitions. Put them in a header next to the driver to remove
the dependency on a specific ARM platform's headers.
Due to the sunxi_mmc_init() prototype, the file was not renamed. None of
the register definitions were changed.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
DM_GPIO is always enable in U-Boot proper for ARCH_SUNXI, and this
driver is never enabled in SPL, so the condition is always true.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
When building this with clang, we get a warning about having excess
parenthesis here, or that we're incorrectly using "==" when we want "=".
Correct these by using the common size macro.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[Andre: Use SZ_512M as per Simon's suggestion]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
So far we have a convoluted #ifdef mesh that guards the early AXP PMIC
setup in board.c. That combination of &&, || and negations is very hard
to read, maintain and especially to extend.
Fortunately we have those same conditions already modelled in the
Kconfig file, so they are actually redundant. On top of that the real
reason we have those preprocessor guards in the first place is about the
symbols that are *conditionally* defined: without #ifdefs the build
would break because of them being undefined for many boards.
To simplify this, just change the guards to actually look at the symbols
needed, so CONFIG_AXP_xxx_VOLT instead of CONFIG_AXPyyy_POWER.
This drastically improves the readability of this code, and makes adding
PMIC support a pure Kconfig matter.
Doing this revealed one bug in Kconfig: there is no axp_set_dcdc4() for
the AXP818, even though CONFIG_AXP_DCDC4_VOLT includes that PMIC.
Since the AXP818 wasn't included when calling axp_set_dcdc4() in board.c,
this wasn't an issue, but becomes one now, so also remove the AXP818 from
the DCDC4 Kconfig symbol.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The sphinx-prompt documentation[0] provides examples on how we can use
prompt as a parameter to simplify the description. Use the same.
While at it, ensure to make all relevant prompts clarified such as gdb
prompts.
[0] http://sbrunner.github.io/sphinx-prompt/
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Title underlines should match the length of the title. Unfortunately
docutils only catches underlines that are too short.
Add some missing empty lines after titles.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
k3-j7200 does not exist in upstream OPTEE. Use j721e as the platform
name. Using k3-j7200 as OPTEE name results in broken boot due to wrong
configuration being picked.
Fixes: c727b81d65 ("doc: board: ti: k3: Reuse build instructions")
Signed-off-by: Nishanth Menon <nm@ti.com>
The build instructions for the hikey960 had some broken links. Update
the links to use new vendor URLs. Also change build instructions to
reference a different file name.
Signed-off-by: Dylan Corrales <deathcamel58@gmail.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
To quote the author:
Since commit [1], Ethernet is broken on TI AM62 and AM64 platforms.
The commit [1] is not the culprit. It just unearths the problem by fixing
the error check in k3-udma.c. This issue was silently being ignored earlier
due to wrong error check. [NULL instead of FDT_ADDR_T_NONE].
Fix the issue by adding the necessary register spaces for the u-boot K3-UDMA
driver for AM62 and AM64 platforms.
These properties will eventually make it into the SoC DTSi files [2] after
which these can be dropped from k3-*-u-boot.dtsi files.
[1] - 5fecea171de3dd ("treewide: use dev_read_addr_*_ptr() where appropriate")
[2] - https://lore.kernel.org/linux-arm-kernel/20230810174356.3322583-1-vigneshr@ti.com/
Update main_bcdma and main_pktdma nodes for native configuration in the
absence of DM services.
Drop duplicate main_pktdma node in k3-am642-sk-u-boot.dtsi.
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Update main_bcdma and main_pktdma nodes for native configuration in the
absence of DM services.
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
_ Fix compilation issue when SYS_DCACHE_OFF and/or SYS_DCACHE_SYS are enabled
_ Fix issue following DT sync with kernel 6.3 for stm32mp15xx-ev1 and DHSOM SoM
_ Enable TCP, IPv6, wget on DH STM32MP15 DHSOM
_ Limit u-boot.itb size to 0x160000 bytes on DH STM32MP15 DHSOM
_ Read auth stats and boot_partition from tamp
- Fix some issues Coverity has reported, update MAINTAINERS file,
another bootstd fix, typo fix in error message, gitignore fix and
update TI's URL in many places.
'git status' shows 'tools/generated/' after running the build, which is
wrong. The corresponding .gitignore rule was already added in commit
c623642d29 ("Adjust gitignore for tools/generated/"), but because of
superfluous 'tools/' part it wasn't in effect. Remove incorrect 'tools/'
part to fix it.
While at it, remove tools/ path incorrectly added to the top-level
.gitignore in commit 801c482207 (".gitignore: ignore misc include,
simple-bin, and tools/generated build artifacts"), as it's required in
the comment on the top of .gitignore:
# NOTE! Don't add files that are generated in specific
# subdirectories here. Add them in the ".gitignore" file
# in that subdirectory instead.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Fixes: c623642d29 ("Adjust gitignore for tools/generated/")
Fixes: 801c482207 (".gitignore: ignore misc include, simple-bin, and tools/generated build artifacts")
During bootstd scanning for bootdevs, if bootdev_hunt_drv() encounters
a device not found error (e.g. ENOENT), let it return a successful status
so that bootstd will continue scanning the next devices, not stopping
prematurely.
Background:
During scanning for bootflows, it's possible for bootstd to encounter a
faulty device controller. Also when the same u-boot is used for another
variant of the same board, some device controller such as SATA might
not exist.
I've found this issue while converting the Marvell Sheevaplug board to
use bootstd. This board has 2 variants, the original Sheevaplug has MMC and
USB only, but the later variant comes with USB, MMC, and eSATA ports. We
have been using the same u-boot (starting with CONFIG_IDE and later with DM
CONFIG_SATA) for both variants. This worked well with the old
envs-scripting booting scheme.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
A power domain id on sandbox should be in the range from zero to
ARRAY_SIZE(scmi_pwdom) - 1. Correct the validity check logic.
Addresses-Coverity-ID: 467401 ("Out-of-bounds write")
Addresses-Coverity-ID: 467405 ("Out-of-bounds read")
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
When we do not have CONFIG_BOUNCE_BUFFER enabled, inside of
scsi_init_dev_desc_priv we never set the 'bb' field to false, we only
initialize it to true when CONFIG_BOUNCE_BUFFER is set. Given that we
have a number of other fields here we had been explicitly setting to
zero, change to first calling memset to clear the struct and then
initialize only the fields that need non-zero default values.
Addresses-Coverity-ID: 467407 ("Uninitialized variables (UNINIT)")
Fixes: 81bd22e935 ("rockchip: block: blk-uclass: add bounce buffer flag to blk_desc")
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Keep track of the re-entries with help of the lr register.
This binary can be re-used and called from various BROM functions.
Only when it's called from the part that handles SPI, NAND or EMMC
hardware it needs to early return to BROM ones.
In download mode when it handles data on USB OTG and UART0
this section must be skipped.
Unlike newer Rockchip SoC models the rk3066 BROM code does not have built-in
support to enter download mode on return to BROM. This binary must check
the boot mode register for the BOOT_BROM_DOWNLOAD flag and reset if it's set.
It then returns to BROM to the end of the function that reads boot blocks.
From there the BROM code goes into a download mode and waits for data
on USB OTG and UART0.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
It's happened that glitches on the STM32_RST and STM32_BOOT lines have
put the STM32 companion microcontroller into DFU mode making it not boot
its FW, rendering it useless for the user.
Considering that the STM32 companion microcontroller is always reset on
a reboot or power cycle, resetting it once again in U-Boot SPL isn't
going to hurt it any more.
For ATtiny companion microcontroller, the situation is a bit different
because a reboot or power cycle doesn't reset it. Additionally, since it
can only be reset with a UPDI reset on the STM32_RST line, and that is
virtually impossible to mistakenly trigger, the ATtiny is unlikely to be
in unwanted reset or enter reset because U-Boot toggles STM32_RST line.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Provide configuration to read cpuid and generate a persistent
MAC address in ethaddr
Signed-off-by: Tim Lunn <tim@feathertop.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Extend the otp driver to read rv1126 otp. This driver code was
adapted from the Rockchip BSP stack.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
RV1126 fails to boot on 2024.01-rc1.
Commit 9e644284ab ("dm: core: Report bootph-pre-ram/sram node as
pre-reloc after relocation") changed the behaviour of bootph-pre-ram, to
limit nodes to spl phase. This caused rv1126 boards to fail to boot with
the current dts.
This patch updates the pmu/grf nodes to bootph-all tags as they are
needed in all phases. This fixes the boot issue on rv1126 boards.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The maximum size of u-boot.itb in SPI NOR on DH STM32MP15 DHSOM is
0x160000 . Define this size in U-Boot config to prevent misconfigured
builds from emitting larger u-boot.itb than the one which fits the
SPI NOR area reserved for the blob.
The SPI NOR layout is as follows:
0x00_0000..0x03_ffff ... SPL 1
0x04_0000..0x07_ffff ... SPL 2
0x08_0000..0x1d_ffff ... U-Boot
0x1e_0000..0x1e_ffff ... Environment 1
0x1f_0000..0x1f_ffff ... Environment 2
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Enable support for TCP protocol, wget, and IPv6 on this platform.
The former two allow users download payload into the U-Boot from
a web server, which may be more convenient or easier to set up
than TFTP server. The later is enabled to future proof the IP
stack on this platform.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The patch fixed by this commit renders ST STM32MP15xx EV1 board and
all DHSOM SoM based boards unbootable from SPI NOR. Fix the damage
by updating -u-boot.dtsi to match the stm32mp15-pinctrl.dtsi update.
Fixes: 08002ffd08 ("ARM: dts: stm32mp: alignment with v6.3")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
QuartzPro64 is a Rockchip RK3588 based SBC by Pine64.
UART and boot over SD/eMMC/RJ45 are tested to work.
Linux commits from next-20231013:
8152d3d070a9 ("arm64: dts: rockchip: Add QuartzPro64 SBC device tree")
Signed-off-by: Tom Fitzhenry <tom@tom-fitzhenry.me.uk>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Cc: Eugen Hristev <eugen.hristev@collabora.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Ondrej Jirman <megi@xff.cz>
Fastboot has been marked as orphaned since 2021.
Since I'm interested in maintaining this, assign myself.
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Lukasz Majewski <lukma@denx.de>
It seems that Lukasz and Marek could get some help in maintaining the
usb gadget drivers.
Assign myself as maintainer.
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Lukasz Majewski <lukma@denx.de>
Xilinx is using standard mtd partition layout for quite a long time. It is
used for testing purpose on evaluation boards.
Also #address/size-cells shouldn't be present without nodes which should
use them that's why move them from zynq-7000.dtsi to nand/nor nodes
directly.
The patch was tested on zc706 and zedboard(with also increasing max
frequency and rx bus width).
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/4c3348981bba32d3892194420d78fe8621c47534.1698837725.git.michal.simek@amd.com
gpio38 is used in SOM's kv260 to reset the Ethernet PHY.
At present, HW reset is not working properly as Tri-state
is enabled for MIO38, causing inappropriate PHY register reads.
Disabled Tri-state for MIO38 to make HW reset work.
Tri-state disable :
ZynqMP> md 0xFF180208 2
ff180208: 00bfe7a3 00000540
Tri-state enable :
ZynqMP> md 0xFF180208 2
ff180208: 00bfe7e3 00000540
Signed-off-by: Tejas Bhumkar <tejas.arvind.bhumkar@amd.com>
Link: https://lore.kernel.org/r/20231020050622.972750-1-tejas.arvind.bhumkar@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The following patch migrates the usage of debug and printf functions
to the relevant logging function as per U-Boot DM guidelines.
Additionally some of the debugging statements have been rearanged for
a more meaningfull debug experience.
aarch64-linux-gnu-size reports 229 bytes less when debug is enabled at
file level, while is just 5bytes more when disabled.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@amd.com>
Link: https://lore.kernel.org/r/20231013123739.2757979-1-ibai.erkiaga-elorza@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The baudrate configured in .config is taken by default by serial. If
change of baudrate is required then the .config needs to changed and
u-boot recompilation is required or the u-boot environment needs to be
updated.
To avoid this, support is added to fetch the baudrate directly from the
device tree file and update.
The serial, prints the log with the configured baudrate in the dtb.
The commit c4df0f6f31 ("arm: mvebu: Espressobin: Set default value for
$fdtfile env variable") is taken as reference for changing the default
environment variable.
The default environment stores the default baudrate value, When default
baudrate and dtb baudrate are not same glitches are seen on the serial.
So, the environment also needs to be updated with the dtb baudrate to
avoid the glitches on the serial.
Also add test to cover this new function.
Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20230921112043.3144726-3-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
This adds support for the Inteno XG6846 board based on the
Broadcom MIPS 6328 SoC.
The default boot will read a uImage from flash and boot it.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Older DesignWare Ethernet MAC versions that this driver supports can
only work with 32-bit DMA source/destination addresses. Some platforms
have no physical RAM at the lowest 4GB address space. For these
platforms the driver must translate DMA addresses to/from physical
memory addresses.
Call translation routines so that properly configured platforms can use
the DesignWare Ethernet MAC. For platforms using device-tree this
usually means adding dma-ranges property to the bus the device node is
in.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
While bringinp up a new board without the MAC fuses programmed,
the following error message was observed:
Error: ethernet@30bf0000 address not set.
Improve the error message to make it clearer the reason of
the failure.
Signed-off-by: Fabio Estevam <festevam@denx.de>
e1000_eth_ids holds compatible strings for e1000 devices, but it
is meaningless as e1000 is a PCI device and there is no such
compatible string assigned to e1000 by the DT bindings community.
Drop it.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Setting the clock delay from the device tree settings
rx-internal-delay-ps and tx-internal-delay-ps was broken:
- The expected value in the device tree is suppose to be a
delay in picoseconds, but the driver only allowed an array index.
- Driver converted this array index to the actual delay in
picoseconds and tried to apply this in the device register. This
however is not a valid register value. The actual logic here was
reversed, it converted an register representation of the delay to
the device tree delay in picoseconds.
Only when the internal delays were NOT configured in the device tree
and they default value of 7 (=2000ps) was used, a valid value was
loaded in the register.
Signed-off-by: Frank de Brabander <debrabander@gmail.com>
There is no reason to setup ROM source if read_rom_hwaddr hook doesn't
exist or reading mac address fails. It is ending up with confusion about
mac address source.
It is nicely visible if you put mac address to DT as
local-mac-address = [ff ff ff ff ff ff];
but also save ethaddr to variables
setenv -f ethaddr 02:18:31:7e:3e:01
Before this patch U-Boot prints that source is ROM
Address in ROM is ff:ff:ff:ff:ff:ff
Address in environment is 02:18:31:7e:3e:01
After that source is DT:
Address in DT is ff:ff:ff:ff:ff:ff
Address in environment is 02:18:31:7e:3e:01
Signed-off-by: Michal Simek <michal.simek@amd.com>
It adds the driver for the internal MDIO bus of HIFEMAC Ethernet
controller. It's based on the mainstream linux driver.
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
It adds the driver for HIFEMAC Ethernet controller found on HiSilicon
SoCs like Hi3798MV200. It's based on the mainstream linux driver, but
quite a lot of code gets rewritten and cleaned up to adopt u-boot driver
model.
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
Marvell LinkStreet switches support Clause 45 MDIO on the internal bus.
C45 read or writes require the register address to be written first to
the SMI PHY Data register, and then a special C45 Write Address Register
OP is used on the SMI PHY Register before making a C45 Read Data Register
OP and being able to actually read the register.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Driver is currently defining the mask and bit shifting itself,
there is no need for that as U-Boot has generic bitfield macros that help
us achieve the same result but in a cleaner way.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Add optional reset control, especially for the Aspeed SOC. For the
hardware without a reset line, the reset assertion/deassertion will be
skipped.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
RFC 5970 states that OPT_BOOTFILE_PARAM (option 60) can be
multiple parameters that start with a 16-bit length field followed
by the parameter. For example:
[ param-len 1 (16-bits) ] [ parameter 1 (variable length) ]
This fix ensure we're considering "param-len 1" in the parsing.
Signed-off-by: Sean Edmond <seanedmond@microsoft.com>
Set upper 32bit address for DMA descriptors and buffer address to support
64-bit addressing.
Signed-off-by: Ley Foon Tan <leyfoon.tan@starfivetech.com>
PALMAS PMIC family has embedded poweroff function used by some
device to initiane device power off. Implement it as sysreset
driver.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
TPS65910/TPS65911 PMICs have embedded power control functions
used by some device to initiane device power off. Implement it as
sysreset driver.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
TPS80031/TPS80032 PMICs have embedded power control functions
used by some device to initiane device power off. Implement it as
sysreset driver.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
MAX77663 PMIC has embedded poweroff function used by some
device to initiane device power off. Implement it as sysreset
driver.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Tegra uses built in Power Management Controller (PMC) to perform
CPU reset. Code to perform this was located in mach-tegra, so lest
create DM driver to handle this.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
The driver provides regulator set/get voltage enable/disable
functions for TI TPS5911 PMIC.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support to bind the regulators/child nodes with the pmic.
Also adds the pmic i2c based read/write functions to access pmic
registers.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The driver provides regulator set/get voltage enable/disable
functions for TI TPS80031/TPS80032 PMICs.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support to bind the regulators/child nodes with the pmic.
Also adds the pmic i2c based read/write functions to access pmic
registers.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support to bind the regulators/child nodes with the pmic.
Also adds the pmic i2c based read/write functions to access pmic
registers.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
dev->driver_data will carry the tail of ldo if there is a number and
if there is no number it will be an error code, anyway it will not be
zero. This results in a wrong ldo regulator detection.
To avoid this check for non-numerical ldo first and then manipulate
dev->driver_data.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Existing PALMAS PMIC driver is fully compatible with TI TPS65913
PMIC found in many Tegra 4 devices, like Tegra Note 7 and ASUS
TF701T. TPS65913 shares same structure of regulators like TPS659038
so data can be reused.
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # NVIDIA Tegratab
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Move ASUS Transformers, Grouper, P895 and P880 config fragments into
their respective device directory in /board/../configs/
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Remove nvidia_board_late_init calls from board since this setup is
performed in board2 of mach-tegra. Call of nvidia_board_late_init
from within the board does not provide any additional data.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS Transformer T30
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # LG P895 T30
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Board specific late init allows vendors to set up different device
or board specific env variables (like serial number, platform name).
In case this information is missing, u-boot will lack info regards
serial or platform.
To avoid this prior nvidia_board_late_init internal generic function
is called which fills required data. In this case platform name is
obtained from get_chip and serialno is filled with SoC id.
Though SoC id is not dedicated to be devices serial but it fits well
in case of restriction of data about device and since SoC is basically
a main chip of the device.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS Transformers
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # Nvidia Tegratab
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Re-crypt support was extended to devices without burnt SBK. In case
SBK is not set, place from where it is read is filled with zeroes.
This patch adds support for ebtupdate function to detect nosbk device
and avoid crypto operations for it.
Tested-by: Maksim Kurnosenko <asusx2@mail.ru>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Tegra 4, same as Tegra 3, requires configuration of CPU and CORE
voltages in the SPL stage to boot properly. Expose function to be
able perform this configuration in the SPL section of the device
board.
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # ASUS TF701T
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Convert refresh USB to enter console. Transformers have full size
USB and a dock keyboard so access to U-Boot console would be handy.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Default configuration matches values which are set in the board
so this configuration is not required.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
TF201 unlike other transformers uses non-fused xcvr value for
its dock USB port. With out it dock USB and SD reader will not
work.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Change boot logic to primary try to boot from USB in dock, then
from microSD and lastly from eMMC.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
TF600T has significant differences (Tegra DSI and DSI panel,
own power supply system) which makes use of common transformer
device tree complicated.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
P1801-T has significant differences (hdmi panel and backlight,
own power supply system) which makes use of common transformer
device tree complicated.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Default-tap and default-trim values are used for eMMC setup
mostly on T114+ devices. As for now, those values are hardcoded
for T210 and ignored for all other Tegra generations. Fix this
by passing tap and trim values from dts.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Tegra MMC driver has hardcoded tap and trim values as for now.
Set default-tap and default-trim values in sdhci nodes to avoid
regressions in case Tegra MMC driver is upated to use dts values.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
As discussed, here is the maintainers update for Snapdragon. Sumit Garg
who maintains a few of the Qualcomm platforms in U-boot has also been
added as a reviewer.
As Ramon has been inactive for some time now, add myself and Neil
Armstrong to maintain Qualcomm efforts going forwards.
Add Sumit Garg who maintains several Qualcomm platforms as reviewer.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
It isn't clear why we need to have two different paths for closing down
the pipe. Unify them and use the Python to avoid this warning:
subprocess.py:1127: ResourceWarning: subprocess 83531 is still running
Note that this code appears to originally have come from [1] and was
committed into the ChromeOS chromiumos/platform/crosutils repo in the
bin/cros_image_to_target.py file. The addition of the extra code path
came later, so that is chosen for the fixes tag.
[1] https://codereview.chromium.org/3391008
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: a10fd93cbc patman: Make command methods return a CommandResult
Buildman assumes that branch names do not have a slash in them, since
slash is used to delimit remotes, etc. This means that a branch called
'WIP/tryme' in remote dm ends up being 'tryme'.
Adjust the logic a little, to try to accommodate this.
For now, no tests are added for this behaviour.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The sandbox should closely mimic other architectures.
Place each function or data in a separate section and let the linker
eliminate unused ones. This will reduce the binary size.
In the linker script mark that u_boot_sandbox_getopt are to be kept.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
According to the TRMs of K3 platform of devices, the ROM boot image
format specifies a "Core Options Field" that provides the capability to
set the boot core in lockstep when set to 0 or to split mode when set
to 2. Add support for providing the same from the binman DTS. Also
modify existing test case for ensuring future coverage.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When symbols switch between the inited data section and the read-only
data section their visbility changes, at present, with the -B option.
This is confusing, since adding 'const' to a variable declaration can
make it look like a significant improvement in bloat. But in fact
nothing has changed.
Add 'r' to the list of symbols types that are recorded, to correct this
problem. Add a constant to make it easier to find this code next time.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
on Peach-pi console every key press is echoed with message
'cros_ec_command: Returned status 1'
this is not proper fix, just hack to disable this message
Signed-off-by: Milan P. Stanić <mps@arvanta.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
cbfsutil completely changed the way that stages are formatted in CBFS.
Adjust the binman implementation to do the same.
This mirrors commit 81dc20e744 in coreboot.
Signed-off-by: Simon Glass <sjg@chromium.org>
cbfsutil changed to 4-byte alignment for filenames instead of 16.
Adjust the binman implementation to do the same.
This mirrors commit 5779ca718c in coreboot.
Signed-off-by: Simon Glass <sjg@chromium.org>
cbfsutil changed to write zero bytes instead of 0xff when a small
padding must be added. Adjust the binman implementation to do the same.
Drop the code which looks for an unused attribute tag, since it is not
used. A future patch moves the attributes to the end of the header in
any case, so no data will follow the attributes.
This mirrors commit f0cc7adb2f in coreboot.
Signed-off-by: Simon Glass <sjg@chromium.org>
cbfsutil changed to skip adding a compression attribute if there is no
compression. Adjust the binman implementation to do the same.
This mirrors commit 105cdf5625 in coreboot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
For tests which fake bintools being missing, we need to reset the list
afterwards, to ensure that future tests do not also see the bintools as
missing.
Reset the list when processing is complete.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
A Change-Id can be useful for traceability purposes, and some projects
may wish to have them preserved. This change makes it configurable
via a new 'keep_change_id' setting.
Signed-off-by: Maxim Cournoyer <maxim.cournoyer@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
i2c updates for v2024.01-rc2
- nuvoton: support standard/fast/fast plus mode
- bootcount: remove legacy i2c driver and implement
DM based version
Bugfixes:
- designware_i2c: adjust timing calculation
SPL probing failed on the StarFive VisionFive 2 board
Heinrich fixed this, by syncing timing calculation with
linux implementation.
+ CI: Use OpenSBI 1.3.1 release for testing
+ riscv: Support resume after exception
+ rng: Support RNG provided by RISC-V Zkr ISA extension
+ board: starfive VF2: Support jtag
+ board: starfive VF2: Support TRNG driver
+ board: sifive unmatched: Move kernel load address
For most source files we can just drop <common.h>. We need to add an
include for <asm/u-boot.h> in a couple of places. Also sort the include
list in memmap-gen3.c while we're here.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
If <common.h> won't be included before <asm/armv8/mmu.h>, we need to
ensure that we have the required type definitions.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Adds to support JH7110 TRNG driver which is based on linux kernel's
jh7110-trng.c. This can support to generate 256-bit random numbers and
128-bit but this makes 256-bit default for convenience.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This imports mmio functions from Linux's arch/riscv/include/asm/mmio.h
to use read/write[b|w|l|q]_relaxed functions.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The Zkr ISA extension (ratified Nov 2021) introduced the seed CSR. It
provides an interface to a physical entropy source.
A RNG driver based on the seed CSR is provided. It depends on
mseccfg.sseed being set in the SBI firmware.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
If CSRs like seed are readable by S-mode, may not be determinable by
S-mode. For safe driver probing allow to resume via a longjmp after an
exception.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
JTAG pins are mapped as below. To access the JTAG pins, we need to
control the GPIO pins from SPL which seems to be the earliest stage for
JTAG.
- JTAG nTRST: GPIO36 / Input
- JTAG TDI: GPIO61 / Input
- JTAG TMS: GPIO63 / Input
- JTAG TCK: GPIO60 / Input
- JTAG TDO: GPIO44 / Output
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Some RISC-V CPUs, such as the T-HEAD XuanTie series, have a
vendor-specific way to invalidate a portion of the instruction cache.
Allow them to override invalidate_icache_range().
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This is required on CPUs which always operate in CLIC mode, such as the
T-HEAD E906 and E907. Per the CLIC specification: "In this mode, the
trap vector base address held in mtvec is constrained to be aligned on a
64-byte or larger power-of-two boundary."
Reported-by: Madushan Nishantha <jlmadushan@gmail.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Clean things up for the next time somebody adds a target.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
U-boot initially loads the kernel image to the kernel_addr_r, and
subsequently relocates it to memory address 0x80200000. Setting
kernel_addr_r to 0x80200000 can eliminate one copy operation.
Signed-off-by: Yong-Xuan Wang <yongxuan.wang@sifive.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
In clk_enable()/clk_disable() functions, when CCF is activated,
we must pass a private clk struct to enable()/disable() ops functions.
Otherwise, the use of a container_of() construction within these ops
should be banned. Because passing a non-private clk struct to
container_of() results in an out of range error.
At the moment, clk-mux, clk-fixed-factor, clk-gate and possibly other
clocks use container_of() in their enable()/disable() functions.
Therefore, for these functions to work correclty, private clk struct
must be passed.
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20230905221649.3577929-1-bigunclemax@gmail.com
The second parameter for clk_release_all is used as an unsigned
(which makes sense) but the function prototype declares it as an int.
This causes warnings/error like such below:
include/clk.h:422:48: error: conversion to ‘int’ from ‘unsigned int’ may change the sign of the result [-Werror=sign-conversion]
422 | return clk_release_all(bulk->clks, bulk->count);
To fix this, changed the type of the count to `unsigned int`
Fixes: 82a8a669b4 ("clk: add clk_release_all()")
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Xavier Drudis Ferran <xdrudis@tinet.cat>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20230619104752.278500-1-eugen.hristev@collabora.com
In commit 5c5992cb90 ("clk: Add debugging for return values"), a
temporary storage variable was added around the ops->get_rate() call
inside clk_get_rate(), so that the result could be passed through
log_ret.
This temporary variable was declared as an int, yet when we look in
struct clk_ops, we can see this needs to be a ulong:
ulong (*get_rate)(struct clk *clk);
This was resulting in a signed to unsigned casting error on our
builds, where a clock value of 0xABCDABCD was being incorrectly cast
to 0xFFFFFFFFABCDABCD.
Signed-off-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20230515195005.1961495-1-nathan.morrison@timesys.com
This has a typo which makes the method inoperable. Correct it so that
'bootflow read' works correctly for ChromeOS.
Signed-off-by: Simon Glass <sjg@chromium.org>
Two bugs have appeared:
- arguments can have an equals sign embedded in them, which must be
considered part of the value
- arguments must fully match the name; partial matches should be
ignored
Fix these and add a test to cover both.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable the bootflow based on this bootmeth if the BootOrder EFI
variable is set.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Compiling sandbox_defconfig with CONFIG_BOOTSTD=n fails:
/usr/bin/ld: drivers/mtd/spi/sf_bootdev.o:
in function `sf_get_bootflow':
/drivers/mtd/spi/sf_bootdev.c:43:(.text+0x96):
undefined reference to `bootmeth_set_bootflow'
Add the missing Kconfig dependency.
Fixes: Fixes: 0c1f4a9fb1 ("bootstd: Add a SPI flash bootdev")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add extension to the 'mmc' command to read out the card registers.
Currently, only the eMMC OCR/CID/CSD/EXTCSD/RCA/DSR register are
supported. A register value can either be displayed or read into
an environment variable.
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
As noted in commit 3a6383207b ("mmc: sdhci: add the quirk for broken
r1b response"), some MMC controllers don't always set the transfer
complete bit with R1b responses.
According to the SD Host Controller Simplified Specification v4.20,
> In the case of a command pairing with response-with-busy[, Transfer
> Complete] is set when busy is de-asserted. Refer to DAT Line Active
> and Command Inhibit (DAT) in the Present State register.
By polling the DAT Line Active bit in the present state register, we can
detect when we are no longer busy, without waiting for a long timeout.
This results in much faster reads/writes on buggy controllers.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Tested-by: Henrik Grimler <henrik@grimler.se>
dm_pci_map_bar() return a value of (void *) already, hence no need
to cast it again before assigning to host->ioaddr.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
mmc_bind() in mmc-uclass.c calls blk_create_devicef() which is
defined in blk-uclass.c, so SPL_BLK is required by SPL_DM_MMC.
Implicitly select SPL_BLK for SPL_DM_MMC.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
enable PSCI reset used for the system reset
Even though Corstone-1000 does not implement the entire PSCI APIs,
it relies on PSCI reset interface for the system reset.
Signed-off-by: Emekcan Aras <emekcan.aras@arm.com>
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
unzip the kernel before executing it
The Corstone-1000 kernel has become too large to fit in the available
storage. Switching to a compressed kernel avoids the problem, but
requires uncompressing it.
Changes made are generated using savedefconfig.
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Signed-off-by: Jon Mason <jon.mason@arm.com>
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Current documentation limits the firmware size to 1.5MB.
When the fTPM and StandaloneMM-based RPMB secure storage is
enabled, firmware size is bigger than that size.
Let's specify the A/B update bank size(4MB) for flash
rawwrite parameter.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
v2023.07 is the last version supporting old NOR flash layout
by default. The later versions of U-Boot, Developerbox is
configured to enable A/B update and new NOR Flash layout
by default.
This commit updates the documentation to pin the U-Boot
version for the old NOR flash layout. It is still useful
for the user wants to replace the factory default EDK II
firmware to U-Boot.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
There are two kinds of NOR flash layout for the Developerbox.
Capsule update for the old layout is no longer available since
it has small capacity for secure world images and can not
house the TA such as fTPM.
This commit removes the definition related to the obsolete
NOR flash layout for the UEFI capsule update.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
PLL calibration needs to be enabled when operating in non fractional
mode. Add the sequence to do a fast calibration when using PLL
in this mode.
Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
1. Fix incorrect ram size of 4GB dram with ECC enabled
2. Fix wrong place to set dram bank size
- The dram bank size should be set in dram_init_banksize
- Dram_init should not access gd->bd because the board info
struct is not reserved yet.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
[trini: Rework slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add uart baud rate table to arbel(npcm8xx) and poleg(npcm7xx)
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
[trini: Rework slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>
This adds a generic I2C bootcounter adhering to driver model to replace
the previously removed legacy implementation.
There is no change in functionality, it can be used on any I2C device.
The device tree configuration may look like this for example:
bootcount {
compatible = "u-boot,bootcount-i2c";
i2cbcdev = <&i2c_rtc>;
offset = <0x11>;
};
Signed-off-by: Philip Richard Oberfichtner <pro@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
This new function enhances the i2c_get_chip*() toolbox by implementing a
variant that does not require a chip_addr. Instead, the desired device
is pointed to by a phandle.
Signed-off-by: Philip Richard Oberfichtner <pro@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
The legacy I2C bootcounter will hereby be removed and eventually
be replaced by a driver model implementation in the follow-up commit.
The legacy driver has the following drawbacks:
- It's not adhering to the driver model
- Settings are grabbed from Kconfig rather than device tree
- i2c_{read,write} are being used instead of dm_i2c_{read,write}
Signed-off-by: Philip Richard Oberfichtner <pro@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
- Two Kconfig content fixes, fix some issues reported by Coverity,
resync get_maintainer.pl (two small fixees), update i2c_eeprom, and
fix an off by one in addrmap_set_entry
Calculate the maximum length of the buffer when writing
across the page boundary. If the buffer length (len)
exceeds the page boundary (pagesize), split it. Use this
length instead of comparing the length with the pagesize,
because if the write start address (offset) is not at the
beginning of a page and the page_offset + len is greater
than the page boundary (pagesize), the write operation
would overflow the current page and the behaviour can be
undefined (e.g. at24).
Signed-off-by: Alex Michel <alex.michel@wiedemann-group.com>
Update U-Boot's version of scripts/get_maintainer.pl to sync it up with
the latest changes to the Linux kernel's version of the same script.
The last sync was with Linux kernel version v5.13-rc6. The commits to
the kernel's get_maintainer.pl since then (starting with the most
recent) are:
11fb48961e52 get_maintainer: Honor mailmap for in file emails
26d98e9f78da get_maintainer: don't remind about no git repo when --nogit is used
Signed-off-by: Tom Rini <trini@konsulko.com>
Similar change was done by commit b4c2c151b1 ("Kconfig: Remove all
default n/no options") and again sync is required.
default n/no doesn't need to be specified. It is default option anyway.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Svyatoslav Ryhel <clamor95@gmail.com> # tegra
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Angelo Dureghello <angelo@kernel-space.org>
Do not leak file descriptor if writing fails.
Correct the error text if opening a file fails.
Addresses-Coverity-ID: 467054 Resource leaks
Fixes: 64fd30d367 ("tools: mkimage: Add StarFive SPL image support")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Make it clear that in the options for setting the console record buffer
sizes that we are talking about buffers for that feature specifically
and not the general console buffers.
Signed-off-by: Tom Rini <trini@konsulko.com>
The > comparison needs to be changed to >= to prevent an out of bounds
write on th next line.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
In SPL probing of the designware_i2c device on the StarFive VisionFive 2
board fails with
dw_i2c: mode 0, ic_clk 1000000, speed 100000,
period 10 rise 1 fall 1 tlow 5 thigh 4 spk 0
dw_i2c: bad counts. hcnt = -4 lcnt = 4
device_probe: i2c@12050000 failed to probe -22
When changing the offset for the high phase from 7 to 3 the device is
probed correctly. This now matches the value from the Linux driver.
Without this fix the memory size of the StarFive VisionFive 2 board cannot
be read from EEPROM.
Fixes: e71b6f6622 ("i2c: designware_i2c: Rewrite timing calculation")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
first version is only support standard mode.
remove this judgment to support standard/fast/fast plus mode.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Changes for v2:
- add commit message
Reviewed-by: Heiko Schocher <hs@denx.de>
- Fix some mpc85xx platforms, fixes for a few TI K3 platforms, enable
usb device and fastboot on verdin-imx8mp, make all QEMU platforms use
the default console buffer sizes, vexpress platform fixes, and update
synquacer flash layout
This was lost in refactoring while some users of the IOT2050 expect it
to work: Make sure that up to 3 USB storage devices are probed.
Fixes: 53873974a4 ("include: armv7: Enable distroboot across all configs")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When building a non-SPL image, relocation is needed. This patch restores
the old behaviour before commit b35316fb67 ("Convert
CONFIG_SPL_INIT_MINIMAL et al to Kconfig") was only defined if
CONFIG_SPL_BUILD was defined.
Fixes: b35316fb67 ("Convert CONFIG_SPL_INIT_MINIMAL et al to Kconfig")
Signed-off-by: Martin Fäcknitz <faecknitz@hotsplots.de>
The SynQuacer Developerbox, in EFI mode, supports A/B capsule
updates and single image ones. The flash layout in the latter case is
outdated, update it with the new offsets and images
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-By: Masahisa Kojima <masahisa.kojima@linaro.org>
To avoid thermal burn out, program thermal shutdown
value in VTM (Voltage and Thermal Manager) IP.
Part of Linux kernel driver (drivers/thermal/k3_j72xx_bandgap.c)
is ported from kernel 6.6-rc1, which sets thermal shutdown values.
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Neha Francis <n-francis@ti.com>
Add MMC disk to FVP's BOOT_TARGET_DEVICES. This allows the user to boot
from MMC devices.
Signed-off-by: Wei Chen <wei.chen@arm.com>
Signed-off-by: Qi Feng <qi.feng@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
In current vexpress_config_probe code, it sets the uclass private data
directly. This will cause one compilation error:
drivers/misc/vexpress_config.c:114:27: error: lvalue required as left operand of assignment
114 | dev_get_uclass_priv(dev) = priv;
| ^
In this patch we set the uclass private data through struct member
.priv_auto, and this compilation error disappears.
Signed-off-by: Wei Chen <wei.chen@arm.com>
Signed-off-by: Qi Feng <qi.feng@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
QEMU print and console buffer sizes have been restricted on QEMU below
their default values.
One of the side effects of the print buffer size restriction is output
truncation of the 'efidebug dh' command.
As QEMU does not have special memory size restrictions remove the settings
from the defconfig files and go with the generic defaults.
Fixes: d0ee7f295d ("Convert CONFIG_SYS_PBSIZE to Kconfig")
Fixes: d31466b382 ("Convert CONFIG_SYS_CBSIZE to Kconfig")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The "simpler" the logic, the higher the probability to not test and get
things wrong, again: The absence of a "-PG2" suffix is not sufficient to
derive that we are on PG1. There is also "IOT2050-ADVANCED-M2".
Finally fix that by exactly matching against the two PG1 device names.
While changing this, we can also drop the not really needed check for
!board_is_sr1 in board_is_m2 and call the boards by their names
("board_is_pg1").
Reported-and-tested-by: Bao Cheng Su <baocheng.su@siemens.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Enable USB device and fastboot support which may be used to load the
Toradex Easy Installer FIT image.
While at it also enable USB mass storage aka UMS support.
Note that the i.MX 8M Plus recovery mode support is based on the USB
boot stage of the BOOTROM and does NOT require USB SDP SPL aka serial
downloader support.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
bootX measurements and measurement API moved to u-boot core:
Up to now, U-Boot could perform measurements and EventLog creation as
described by the TCG spec when booting via EFI.
The EFI code was residing in lib/efi_loader/efi_tcg2.c and contained
both EFI specific code + the API needed to access the TPM, extend PCRs
and create an EventLog. The non-EFI part proved modular enough and
moving it around to the TPM subsystem was straightforward.
With that in place we can have a common API for measuring binaries
regardless of the boot command, EFI or boot(m|i|z), and contructing an
EventLog.
I've tested all of the EFI cases -- booting with an empty EventLog and
booting with a previous stage loader providing one and found no
regressions. Eddie tested the bootX part.
Eddie also fixed the sandbox TPM which couldn't be used for the EFI code
and it now supports all the required capabilities. This had a slight
sideeffect in our testing since the EFI subsystem initializes the TPM
early and 'tpm2 init' failed during some python tests. That code only
opens the device though, so we can replace it with 'tpm2 autostart'
which doesn't error out and still allows you to perfom the rest of the
tests but doesn't report an error if the device is already opened.
There's a few minor issues with this PR as well but since testing and
verifying the changes takes a considerable amount of time, I prefer
merging it now.
Heinrich has already sent a PR for -master containing "efi_loader: fix
EFI_ENTRY point on get_active_pcr_banks" and I am not sure if that will
cause any conflicts, but in any case they should be trivial to resolve.
Both the EFI and non-EFI code have a Kconfig for measuring the loaded
Device Tree. The reason this is optional is that we can't reason
when/if devices add random info like kaslr-seed, mac addresses etc in
the DT. In that case measurements are random, board specific and
eventually useless. The reason it was difficult to fix it prior to this
patchset is because the EFI subsystem and thus measurements was brought
up late and DT fixups might have already been applied. With this
patchset we can measure the DT really early in the future.
Heinrich also pointed out that the two Kconfigs for the DTB measurements
can be squashed in a single one and that the documentation only explains
the non-EFI case. I agree on both but as I said this is a sane working
version, so let's pull this first it's aleady big enough and painful to
test.
Pull request efi-2024-01-rc2-2
Documentation:
* Bump urllib3 version
* Replace references to dm_dump_all() with dm_dump_tree()
* Update description of build dependencies for Alpine Linux
* Fix typo in gpt example
* Fix ordering of shell commands
UEFI:
* Move misplace EFI_ENTRY macro
efi_tcg2_get_active_pcr_banks doesn't immediately call the
EFI_ENTRY() wrapper once it enters the function. Move the call a
few lines above to cover the error cases properly as well.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
While unlikely to be a direct issue for us, urllib3 before 2.0.7 is
vulnerable to CVE-2023-45803, so bump our version up.
Reported-by: GitHub dependabot
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
- Fix environment saving for new Android boot features on vim3*_android
- Add SPIFC support for Amlogic A1
- Add DFU RAM boot step when booting over USB
- kirkwood: Enable bootstd on some boards (Tony)
- mvebu: turris_mox: Extend to support RIPE Atlas Probe (Marek)
- mvebu/bubt: Support eMMC data partition booting (Josua)
commit 789ed27842 ("test/py: replace 'tpm2 init, startup, selftest' sequences")
changed some of the tpm2 init sequences to 'tpm2 autostart' instead of
calling 'tpm init', 'tpm startup TPM2_SU_CLEAR', 'tpm2 self_test full'.
The autostart command calls the afforementioned sequence and on top of
that deals with the 'tpm2 init' return codes if the tpm is already
started. Since we initialize the tpm from various subsystems now,
replace the last remaining instances of 'tpm2 init' with 'tpm2
autostart'. Since the latter calls 'tpm2 init' anyway we will still be
implicitly testing the validity of that command
It's worth noting that since 'tpm2 autostart' performs the startup and
self tests sequences of the tpm we could drop
'test_tpm2_sandbox_self_test_full' and 'test_tpm2_startup, but let's
keep the since they test tpm commands and options
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
We currently use PCR 0 for testing the PCR read/extend functionality in
our selftests. How ever those PCRs are defined by the TCG spec for
platform use. For example if the tests run *after* the efi subsystem
initialization, which extends PCRs 0 & 7 it will give a false positive.
So let's switch over to a PCR which is more suitable and is defined for
OS use. It's worth noting that we are using PCR10 here, since PCR9 is
used internally by U-Boot if we choose to measure the loaded DTB
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
efi_tcg2_get_active_pcr_banks doesn't immediately call the
EFI_ENTRY() wrapper once it enters the function. Move the call a
few lines above to cover the error cases properly as well.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Add a configuration option to measure the boot through the bootm
function. Add the measurement state to the booti and bootz paths
as well.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Ilias: Added some info on Kconfig explaining this is when booting !EFI
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Add TPM2 functions to support boot measurement. This includes
starting up the TPM, initializing/appending the event log, and
measuring the U-Boot version. Much of the code was used in the
EFI subsystem, so remove it there and use the common functions.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
For the API moving around from EFI -> u-boot core
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
For EFI testing
Tested-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The driver needs to support getting the PCRs in the capabilities
command. Fix various other things and support the max number
of PCRs for TPM2.
Remove the !SANDBOX dependency for EFI TCG2 as well.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The R-Car Gen3 SD_CLK_CTRL register does not use BIT(16) to implement
divider 1/1024, instead BIT(16) is reserved bit and divider 1/1024 is
not supported. The divider 1/1024 is specific to Socionext variant of
the IP, as is indicated by Linux commit:
0196c8db8363 ("mmc: tmio: move tmio_mmc_set_clock() to platform hook")
"
Socionext (and Panasonic) uses bit 10 (CLKSEL) for 1/1. Also, newer
versions of UniPhier SoC variants use bit 16 for 1/1024.
"
Do not set the TMIO_SD_CAP_DIV1024 on Renesas R-Car platforms even if
the IP VERSION register does exist, and indicates IP version is newer
or equal to version 1.0 . The IP version 1.0 or newer does not imply
presence of the 1/1024 divider.
Since the TMIO driver is used exactly by two supported platforms, that
is Renesas R-Car and Socionext UniPhier, it is OK to check whether the
TMIO_SD_CAP_RCAR capability is not set to identify the UniPhier platform
and add the capability only on that platform.
Fixes: 58c35b17aa ("mmc: matsushita-common: Always check controller version")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Thuan Nguyen Hong <thuan.nguyen-hong@banvien.com.vn>
Unconditionally check for errors even after successful reception
of IRQ flag, since the hardware may set both an IRQ completion
flag and an error flag at the same time.
This mode of failure happens in case of an error during transfer,
in which case the hardware may set the expected IRQ completion
flag as well as error flags. The later is currently not checked
by the driver and such an error is not detected. Improve the
error detection.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Thuan Nguyen Hong <thuan.nguyen-hong@banvien.com.vn>
Add boot over DFU RAM as an alternate to running script at
a fixed address like done today.
The main culprit is that it's not possible to do that
on G12A/Sm1 platforms due to changes in the USB boot protocol.
With this, U-Boot will present a DFU device with a ram slot where
the Host could write a fitImage or legacy U-Boot image, then with the
detach command boot will continue trying to boot the uploaded image.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20231023-usb-dfu-boot-v1-3-df9d121c67c1@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
A38x bootrom only searches 2 sectors when booting from eMMC,
irregardless of data or boot partition: 0 & 4096.
For eMMC boot partitions sector 0 is fine, but on data partition it
conflicts with MBR.
Change bubt command default to 4096 for eMMC data partition only, to
allow using an MBR partition table on the eMMC data partition while also
booting from it.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Disarm the error message forcing u-boot/spl image to be located at
sector 0 on eMMC data-partition and microSD.
Offset 0 makes sense on eMMC boot partitions only, data partition must
use 4096 to avoid conflicting with MBR.
Valid offsets when booting from microSD, reported by boot-rom v1.73:
BootROM: Bad header at offset 00000200
BootROM: Bad header at offset 00004400
BootROM: Bad header at offset 00200000
BootROM: Bad header at offset 00400000
BootROM: Bad header at offset 00600000
BootROM: Bad header at offset 00800000
BootROM: Bad header at offset 00A00000
BootROM: Bad header at offset 00C00000
BootROM: Bad header at offset 00E00000
BootROM: Bad header at offset 01000000
BootROM: Bad header at offset 01200000
BootROM: Bad header at offset 01400000
BootROM: Bad header at offset 01600000
BootROM: Bad header at offset 01800000
BootROM: Bad header at offset 01A00000
BootROM: Bad header at offset 01C00000
BootROM: Bad header at offset 01E00000
BootROM: Bad header at offset 02000000
BootROM: Bad header at offset 02200000
BootROM: Bad header at offset 02400000
BootROM: Bad header at offset 02600000
BootROM: Bad header at offset 02800000
BootROM: Bad header at offset 02A00000
BootROM: Bad header at offset 02C00000
BootROM: Bad header at offset 02E00000
Valid offsets when booting from eMMC:
BootROM: Bad header at offset 00000000
BootROM: Bad header at offset 00200000
Switching BootPartitions.
BootROM: Bad header at offset 00000000
BootROM: Bad header at offset 00200000
Fixes: 2226ca1734 ("arm: mvebu: Load U-Boot proper binary in SPL code based on kwbimage header")
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Extend Turris Mox board code to support CZ.NIC's RIPE Atlas Probe.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
- Remove common.h in a number of places and make checkpatch.pl complain
about its use in all cases, allow the mbr command to handle 4 primary
partitions, fix an issue with the pstore command, fix a problem with
cli parsing of escape sequences, remove and ignore more files, allow
for the serial port to be flushed with every print (for debugging),
and add SCMI power domain support.
When debugging, one sometimes only gets partial output lines or
nothing at all from the last printf, because the uart has a largish
buffer, and the code after the printf() may cause the CPU to hang
before the uart IP has time to actually emit all the characters. That
can be very confusing, because one doesn't then know exactly where the
hang happens.
Introduce a config knob allowing one to wait for the uart fifo to
drain whenever a newline character is printed, roughly corresponding
to the effect of setvbuf(..., _IOLBF, ...) in ordinary C programs.
Since this uses IS_ENABLED() instead of cpp ifdef, we can remove the
ifdef around the _serial_flush() definition - if neither
CONSOLE_FLUSH_SUPPORT or CONSOLE_FLUSH_ON_NEWLINE are enabled, the
compiler elides _serial_flush(), but it won't warn about it being
unused.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Simon Glass <sjg@chromium.org>
This ut has tests for the SCMI power domain protocol as well as DM
interfaces for power domain devices.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
SCMI power domain management protocol is supported on sandbox
for test purpose. Add fake agent interfaces and associated
power domain devices.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
In this patch, added are helper functions to directly manipulate
SCMI power domain management protocol. DM compliant power domain
driver will be implemented on top of those interfaces in a succeeding
patch.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Current code allows up to 3 MBR partitions without extended one.
If more than 3 partitions are required, then extended partition(s)
must be used.
This commit allows up to 4 primary MBR partitions without the
need for extended partition.
Add mbr test unit. In order to run the test manually, mmc6.img file
of size 12 MiB or greater is required in the same directory as u-boot.
Test also runs automatically via ./test/py/test.py tool.
Running mbr test is only supported in sandbox mode.
Signed-off-by: Alex Gendin <agendin@matrox.com>
[ And due to some further changes for testing ]
Signed-off-by: Simon Glass <sjg@chromium.org>
u-boot adds reserve-memory node, if it's missing, with following
properties:
```
reserved-memory {
#address-cells = <2>;
#size-cells = <2>;
ranges;
}
```
But with these default address-cells and size-cells values, pstore
isn't working on A64. Root node for A64 defines 'address-cells' and
'size-cells' as 1.
dtc complains if reserved-memory has different address-cells and
size-cells.
```
Warning (ranges_format): /reserved-memory:ranges: empty "ranges"
property but its #address-cells (2) differs from / (1)
```
This patch takes into account address-cells and size-cells of the root
node and uses them as values for new reserved-memory node.
Signed-off-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
make rock5b-rk3588_defconfig
make
git status
before
~~~~~~~
On branch master
Your branch is ahead of 'origin/master' by 1 commit.
(use "git push" to publish your local commits)
Untracked files:
(use "git add <file>..." to include in what will be committed)
include/autoconf.mk
include/autoconf.mk.dep
include/config.h
mkimage-in-simple-bin-spi.mkimage-rockchip-tpl
mkimage-in-simple-bin-spi.mkimage-u-boot-spl
mkimage-in-simple-bin.mkimage-rockchip-tpl
mkimage-in-simple-bin.mkimage-u-boot-spl
simple-bin-spi.map
simple-bin.fit.fit
simple-bin.fit.itb
simple-bin.map
tools/generated/
after
~~~~~~~
On branch master
Your branch is ahead of 'origin/master' by 1 commit.
(use "git push" to publish your local commits)
nothing to commit, working tree clean
Signed-off-by: John Clark <inindev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
make rock5b-rk3588_defconfig
make
make clean
git status
before
~~~~~~~
On branch master
Your branch is up to date with 'origin/master'.
Untracked files:
(use "git add <file>..." to include in what will be committed)
include/autoconf.mk
include/autoconf.mk.dep
include/config.h
mkimage-in-simple-bin-spi.mkimage-rockchip-tpl
mkimage-in-simple-bin-spi.mkimage-u-boot-spl
mkimage-in-simple-bin.mkimage-rockchip-tpl
mkimage-in-simple-bin.mkimage-u-boot-spl
simple-bin.fit.fit
simple-bin.fit.itb
after
~~~~~~~
On branch master
Your branch is ahead of 'origin/master' by 1 commit.
(use "git push" to publish your local commits)
nothing to commit, working tree clean
Signed-off-by: John Clark <inindev@gmail.com>
We can remove common.h from most cases of the code here, and only a few
places need an additional header instead.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>
We can remove common.h from most cases of the code here, and only a few
places need an additional header instead.
Signed-off-by: Tom Rini <trini@konsulko.com>
We can remove common.h from most cases of the code here, and only a few
places need an additional header instead.
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Michal Simek <michal.simek@amd.com>
We can remove common.h from most cases of the code here, and only a few
places need an additional header instead.
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Angelo Dureghello <angelo@kernel-space.org>
We can remove common.h from most cases of the code here, and only a few
places need an additional header instead.
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
These files references a number of types that are defined in
<linux/types.h> (and so forth), so include it here rather than rely on
indirect inclusion.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At this point in time we should not add common.h to any new files, so
make checkpatch.pl complain.
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Unexpected 'Esc' key presses are accumulated internally, even if it is
already clear that the current escape sequence is invalid. This results
in weird behaviour. For example, the next character after 'Esc' key
simply disappears from input and 'Unknown command' is printed
after 'Enter'.
This commit fixes some issues with extra 'Esc' keys entered by user:
1. Sequence <Esc><Esc><Enter> right after autoboot stop gives:
=>
nknown command 'ry 'help'
=>
2. Sequence <Esc><p><r><i><Enter> gives:
=> ri
Unknown command 'ri' - try 'help'
=>
3. Extra 'Esc' key presses break backspace functionality.
Signed-off-by: Yurii Monakov <monakov.y@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Add Board: rk3588 NanoPC-T6, Orange Pi 5, Orange Pi 5 Plus;
- clk driver fix for rk3568 and rk3588;
- rkmtd cmd support for rockchip nand device;
- dts update and sync from linux;
Enable rkmtd command for testing with sandbox_defconfig
and sandbox64_defconfig.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add Rockchip rkmtd test:
Create/attach/detach RKMTD device.
Send/read data with Rockchip boot block header.
Test that reusing the same label should work.
Basic test of 'rkmtd' commands.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The command rkmtd creates a virtual block device to transfer
Rockchip boot block data to and from NAND with block orientated
tools like "ums" and "rockusb".
It uses the Rockchip MTD driver to scan for boot blocks and copies
data from the first block in a GPT formated virtual disk.
Data must be written in U-boot "idbloader.img" format and start at
partition "loader1" offset 64. The data header is parsed
for length and offset. When the last sector is received
it erases up to 5 erase blocks on NAND and writes bootblocks
in a pattern depending on the NAND ID. Data is then verified.
When a block turns out bad the block header is discarded.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently bounce buffer support is enabled for all block devices
when available. Add a flag to blk_desc to enable only on demand.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add rkmtd class and drivers to create a virtual block device
to transfer Rockchip boot block data to and from NAND with
block orientated tools like "ums" and "rockusb".
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Prepare a rkmtd UCLASS in use for writing Rockchip boot blocks
in combination with existing userspace tools and rockusb command.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
On Rockchip SoCs the first boot stages are written on NAND
with help of manufacturer software that uses a different format
then the MTD framework. Skip the automatic BBT scan with the
NAND_SKIP_BBTSCAN option to be able to pass the driver probe
function and to let the original data unchanged.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Xunlong Orange Pi 5 Plus is a single-board computer based on the
Rockchip RK3588 SoC. The board provides abundant interfaces, including
two HDMI output ports, one HDMI input port, two 2.5G Ethernet ports,
M.2 M-Key slot, M.2 E-Key slot, two USB 3.0, two USB 2.0, and two Type-C.
Features tested on a Orange Pi 5 Plus 4GB v1.2:
- SD-card boot
- eMMC boot
- SPI Flash boot
- PCIe/NVMe
- USB 2.0 host
- Ethernet
Device tree is imported from linux v6.7-rockchip-dts64-1 tag.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Xunlong Orange Pi 5 is a single-board computer based on the Rockchip
RK3588S SoC. The board provides abundant interfaces, HDMI output, GPIO
interface, M.2 PCIe2.0, Type-C, Gigabit LAN port, 2*USB2.0, 1*USB3.0,
etc.
Features tested on a Orange Pi 5 4GB v1.2:
- SD-card boot
- SPI Flash boot
- PCIe/NVMe
- USB 2.0 host
- Ethernet
Device tree is imported from linux v6.7-rockchip-dts64-1 tag.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for XMC XM25QU128C (128M-bit) Serial Flash memory. Used on
the Xunlong Orange Pi 3B, 5 and 5 Plus boards.
Datasheet:
https://www.xmcwh.com/uploads/806/XM25QU128C_Ver2.0.pdf
Signed-off-by: Ricardo Pardini <ricardo@pardini.net>
[jonas@kwiboo.se: update commit message]
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The device tree for rk3588 and rock-5b contain usb3 nodes that have
deviated too much from current state of submitted mainline linux usb3
patches, see [1].
Sync usb3 related nodes from latest patches and collaboras rk3588 tree
so that dwc3-generic driver can be updated to include support for the
rockchip,rk3588-dwc3 compatible in the future, use rockchip,rk3568-dwc3
compatible until final node is merged in linux maintainer tree.
[1] https://lore.kernel.org/lkml/20231009172129.43568-1-sebastian.reichel@collabora.com/
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable support for PCIe SATA cards and the on-board SATA controller.
This also revert use of CONFIG_PCI_INIT_R in order to speed up boot from
eMMC or SD-cards. Standard boot will initialize pci after faster boot
media have been enumerated.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Christopher Obbard <chris.obbard@collabora.com>
Tested-by: Christopher Obbard <chris.obbard@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable Kconfig options for the two USB 2.0 ports and bottom USB 3.0 port
on ROCK 5 Model A.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This brings in more colours, e.g. ORANGE needed for the QuartzPro64 DT.
Linux commits:
472d7b9e8141 ("dt-bindings: leds: Expand LED_COLOR_ID definitions")
Signed-off-by: Tom Fitzhenry <tom@tom-fitzhenry.me.uk>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add ahci sata bootdev and corresponding hunting function.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
When the boot_targets environment variable is used with the distro-boot
scripts, each device is included individually. For example, if there
are three mmc devices, then we will have something like:
boot_targets="mmc0 mmc1 mmc2"
In contrast, standard boot supports specifying just the uclass, i.e.:
boot_targets="mmc"
The intention is that this should scan all MMC devices, but in fact it
currently only scans the first.
Update the logic to handle this case, without required BOOTSTD_FULL to
be enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Date Huang <tjjh89017@hotmail.com>
Reported-by: Vincent Stehlé <vincent.stehle@arm.com>
Reported-by: Ivan Ivanov <ivan.ivanov@suse.com>
Tested-by: Ivan T.Ivanov <iivanov@suse.de>
The current logic for "bootflow mmc" is flawed since it checks the
uclass of the bootdev instead of its parent, the media device. Correct
this and add a test that covers this scenario.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Ivan T.Ivanov <iivanov@suse.de>
Scan the USB bus as well, so we can check that different uclasses work
correctly in boot_targets
update the function comment with more detail.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Ivan T.Ivanov <iivanov@suse.de>
This commit was intended to allow all bootdevs in each boot_targets
entry to be scanned. However it causes bad ordering with bootdevs, e.g.
scanning Ethernet bootdevs when it should be keeping to mmc.
Revert it so we can try another approach.
This reverts commit e824d0d0c2.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Ivan T.Ivanov <iivanov@suse.de>
At this point we have all of the defconfigs maintained again, so
re-enable the check to prevent further regressions.
Signed-off-by: Tom Rini <trini@konsulko.com>
Second set of u-boot-at91 features for the 2024.01 cycle
This feature set a new board named Conclusive KSTR sama5d27 with some
small prerequisites patches.
This is mostly about support for the Allwinner R528/T113s SoC, which is
reportedly the same die as the Allwinner D1, but with the two
Arm Cortex-A7 cores activated instead of the RISC-V one.
Using sunxi code outside of arch/arm proved to be difficult, so apart
from enabling this Arm SoC, the patches also prepare for more refactoring
to get the D1 nicely supported some day:
- We get rid of some Kconfig (hard-)coded GPIO pins, responsible for
enabling regulators.
- The GPIO code is moved out of arch/arm, into drivers/gpio.
- Some definitions are moved out of header files under asm/arch.
- Some T113s/D1 specific definitions are guarded by a generic Kconfig
symbol (CONFIG_SUNXI_GEN_NCAT2).
- The DRAM controller initialisation code is located under drivers/ram.
- The base SoC .dtsi files are shared (under arch/riscv, as in Linux).
Of course there are also the usual new SoC specific patches, like clock
and pinmux descriptions, alongside a rework of the pinctrl code, since
Allwinner changed the GPIO register layout, for the first time since
sunxi's inception.
On top of this the PSCI code sees some update, to provide SMP services
for R528/T113s boards. Many thanks to Sam for providing this code and
staying strong through the review cycles.
The final patch enables support for one popular board, I hope to see
more DTs and defconfigs contributed in the future!
Many thanks to all the various contributors, testers and reviewers,
that series was a real team effort!
Introduce EVT_SETTINGS_R, triggered post-relocation and before console
init.
This event gives an option to perform any platform-dependent setup,
which needs to take place before show_board_info(). Usage examples
include readout of EEPROM stored settings.
Signed-off-by: Artur Rojek <artur@conclusive.pl>
Reviewed-by: Simon Glass <sjg@chromium.org>
Rename populate_serial_number() to a more descriptive
serial_read_from_eeprom() and provide the missing function prototype.
This is useful for boards that wish to read their serial number from
EEPROM at init.
Signed-off-by: Artur Rojek <artur@conclusive.pl>
Reviewed-by: Simon Glass <sjg@chromium.org>
Sync the rk3328-rock64 dts from v6.6-rc5.
See Linux kernel commit for details:
03633c4ef1fb ("arm64: dts: rockchip: fix USB regulator on ROCK64")
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The NanoPC-T6 is a Rockchip RK3588 based SBC by FriendlyElec.
There are four variants depending on the DRAM size: 4G/32GB eMMC,
8G/64GB eMMC, 16G/16MB SPI NOR, and 16G/256GB eMMC/16MB SPI NOR
Specifications:
CPU: Rockchip RK3588, 4x Cortex-A76 (up to 2.4GHz)
+ 4x Cortex-A55 (up to 1.8GHz)
GPU: Mali-G610 MP4
VPU: 8K@60fps H.265 and VP9 decoder, 8K@30fps H.264 decoder,
4K@60fps AV1 decoder, 8K@30fps H.264 and H.265 encoder
NPU: 6TOPs, supports INT4/INT8/INT16/FP16
RAM: 64-bit 4GB/8GB/16GB LPDDR4X at 2133MHz
eMMC: 0GB/32GB/64GB/256GB HS400
MicroSD Slot: MicroSD SDR104
PCIe 3.0: M.2 M-Key x1, PCIe 3.0 x4 for NVMe SSDs up to 2,500 MB/s
Ethernet: PCIe 2.5G 2x Ethernet (RTL8125BG)
PCIe 2.1: M.2 E-Key x1, PCIe 2.1 x1 and USB2.0 Host,
supports M.2 WiFi and Bluetooth
4G Module: MiniPCIe x1, MicroSIM Card Slot x1
Audio Out: 3.5mm jack for stereo headphone output
Audio In: 2.0mm PH-2A connector for analog microphone input
Video Input: standard HDMI input port, up to 4Kp60
2x 4-lane MIPI-CSI, compatible with MIPI V1.2
Video Output: 2x standard HDMI output ports compatible with HDMI2.1,
HDMI2.0, and HDMI1.4
2x 4-lane MIPI-DSI, compatible with MIPI DPHY 2.0 or CPHY 1.1
USB-A: USB 3.0, Type A
USB-C: Full function USB Type‑C port, DP display up to 4Kp60, USB 3.0
40-pin 2.54mm header connector: up to 2x SPIs, 6x UARTs, 1x I2Cs,
8x PWMs, 2x I2Ss, 28x GPIOs
Debug UART: 3 Pin 2.54mm header, 3V level, 1500000bps
Onboard IR receiver: 38KHz carrier frequency
RTC Battery: 2 Pin 1.27/1.25mm RTC battery connector for low power
RTC IC HYM8563TS
5V Fan connector
Working Temperature: 0C to 70C
Power: 5.5*2.1mm DC Jack, 12VDC input
Dimensions: 110x80x1.6mm (without case) / 86x114.5x30mm (with case)
Kernel commits:
893c17716d0c ("arm64: dts: rockchip: Add NanoPC T6")
a721e28dfad2 ("arm64: dts: rockchip: Add NanoPC T6 PCIe Ethernet support")
ac76b786cc37 ("arm64: dts: rockchip: Add NanoPC T6 PCIe e-key support")
Signed-off-by: John Clark <inindev@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
rk3588 frac pll:
FFVCO = ((m + k / 65536) * FFIN) / p
FFOUT = ((m + k / 65536) * FFIN) / (p * 2s)
k is the original code, but the K[15:0] is complement code
(6'b1000_0000_0000_0000 <= K[15:0] <= 16'b0111_1111_1111_1111),
need to be converted.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable mini PCIe slot, pcie3x1 node, now that the PCIe PHY driver
support bifurcation.
A pinctrl is assigned for reset-gpios or the device may freeze running
pci enum and nothing is connected to the mini PCIe slot.
Also drop the AHCI_PCI Kconfig option as this option is not required for
a functional M.2 SATA drive slot.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The MangoPi MQ-R board uses an Allwinner T113s Soc (with 128MB of
embedded DRAM), support for which was just added to the code.
Since the devicetree was already synced from the latest Linux kernel
tree, all we need is a _defconfig file to add support for the board.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Since the sunxi support nowadays generally prefers #defined register
offsets instead of modeling register layouts using C structs, now is a
good time to do this for PSCI as well. This patch moves away from using
the structs `sunxi_cpucfg_reg` and `sunxi_prcm_reg` in psci.c.
The former struct and its associated header file existed only to support
PSCI code, so also delete them altogether.
Signed-off-by: Sam Edwards <CFSworks@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
This is to prepare for R528, which does not have the typical
"CPUCFG" block; it has a "CPUX" block which provides these
same functions but is organized differently.
Moving the hardware-access bits to their own functions separates the
logic from the hardware so we can reuse the same logic.
Signed-off-by: Sam Edwards <CFSworks@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
This patch restructures psci.c to get away from the "many different
function definitions switched by #ifdef" paradigm to the preferred style
of having a single function definition with `if (IS_ENABLED(...))` to
make the optimizer include only the appropriate function bodies instead.
There are no functional changes here.
Signed-off-by: Sam Edwards <CFSworks@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
At the moment we have each SoC's memory map defined in its own cpu.h,
which is included in include/configs/sunxi_common.h. This will be a
problem with the introduction of Allwinner RISC-V support.
Remove the inclusion of that header file from the common config header,
instead move the required serial base addresses (for the SPL) into a
separate header file. Then include the original cpu.h file only where
we really need it, which is only under arch/arm now.
This disentangles the architecture specific header files from the
generic code.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Add support for eMMC (SMHC2) pin pull ups for R528 boards.
The D1 and T113s (and even R329) SoCs do not support 8-bit eMMC anymore,
so it's just four data pins to cover here.
Signed-off-by: Okhunjon Sobirjonov <Okhunjon.Sobirjonov@Mec-electronics.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
[Andre: adjust commit message]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This adds the remaining code bits to teach U-Boot about Allwinner's
newest SoC generation. This was introduced with the RISC-V based
Allwinner D1 SoC, which actually shares a die with the ARM cores versions
called R528 (BGA, without DRAM) and T113s (QFP, with embedded DRAM).
This adds the new Kconfig stanza, using the two newly introduced symbols
for the new SoC generation and pincontroller. It also adds the new symbols
to the relavent code places, to set all the hardcoded bits directly.
We need one DT override:
The ARM core version of the DT specifies the CPUX watchdog as
"reserved", which means it won't be recognised by U-Boot. Override this
in our generic sunxi-u-boot.dtsi, to let U-Boot pick up this watchdog,
so that the generic reset driver will work.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The Allwinner R528/T113-s/D1/D1s SoCs all share the same die, so use the
same DRAM initialisation code.
Make use of prior art here and lift some code from awboot[1], which
carried init code based on earlier decompilation efforts, but with a
GPL2 license tag.
This code has been heavily reworked and cleaned up, to match previous
DRAM routines for other SoCs, and also to be closer to U-Boot's coding
style and support routines.
The actual DRAM chip timing parameters are included in the main file,
since they cover all DRAM types, and are protected by a new Kconfig
CONFIG_SUNXI_DRAM_TYPE symbol, which allows the compiler to pick only
the relevant settings, at build time.
The relevant DRAM chips/board specific configuration parameters are
delivered via Kconfig, so this code here should work for all supported
SoCs and DRAM chips combinations.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Sam Edwards <CFSworks@gmail.com>
At the moment all Allwinner DRAM initialisation routines are stored in
arch/arm/mach-sunxi, even though those "drivers" are just a giant
collection of writel's, without any architectural dependency.
The R528/T113-s SoC (with ARM cores) and the D1/D1s Soc (with RISC-V
cores) share the same die, so should share the same DRAM init routines as
well.
To prepare for this, add a new sunxi directory inside drivers/ram, and
add some stub entries to prepare for the addition of the share DRAM code
for those SoCs.
The RISC-V D1(s) SoCs will probably use SPL_DM, so for that SoC this
would be the right directory anyway.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The PLL_PERIPH0 clock changed a bit in the D1/R528/T113s SoCs: there is
new P0 divider at bits [18:16], and the M divider is 1.
Add code to support this version of "PLL6".
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The D1/R528/T113s SoCs introduce a new "LDO enable" bit in the CPUX_PLL.
Just enable that when we program that PLL.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Since the D1 CCU binding is defined, we can add support for its
gates/resets, following the pattern of the existing drivers.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Apart from using the new pinctrl MMIO register layout, the Allwinner D1
and related SoCs still need to usual set of mux values hardcoded in
U-Boot's pinctrl driver.
Add the values we need so far to this list, so that DM based drivers
will just work without further ado.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Allwinner seems to typically stick to a common MMIO memory map for
several SoCs, but from time to time does some breaking changes, which
also introduce new generations of some peripherals. The last time this
happened with the H6, which apart from re-organising the base addresses
also changed the clock controller significantly. We added a
CONFIG_SUN50I_GEN_H6 symbol back then to mark SoCs sharing those traits.
Now the Allwinner D1 changes the memory map again, and also extends the
pincontroller, among other peripherals.
To mark this generation of SoCs, add a CONFIG_SUNXI_GEN_NCAT2 symbol,
this name is reportedly used in the Allwinner BSP code, and prevents us
from inventing our own name.
Add this new symbol to some guards that were already checking for the H6
generation, since many features are shared between the two (like the
renovated clock controller).
This paves the way to introduce a first user of this generation.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Samuel Holland <samuel@sholland.org>
For the first time since at least the Allwinner A10 SoCs, the D1 (and
related cores) use a new pincontroller MMIO register layout, so we
cannot use our hardcoded, fixed offsets anymore.
Ideally this would all be handled by devicetree and DM drivers, but for
the DT-less SPL we still need the legacy interfaces.
Add a new Kconfig symbol to differenciate between the two generations of
pincontrollers, and just use that to just switch some basic symbols.
The rest is already abstracted enough, so works out of the box.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Sam Edwards <CFSworks@gmail.com>
Tested-by: Sam Edwards <CFSworks@gmail.com>
Tested-by: Samuel Holland <samuel@sholland.org>
On the Allwinner platform we were describing a quite comprehensive
memory map in a per-SoC header unser arch/arm.
In the old days that was used by every driver, but nowadays it should
only be needed by SPL drivers (not using the DT). Many addresses in
there were never used, and some are not needed anymore.
To avoid a dependency on CPU specific headers in an arch specific
directory, move the definition of the pinctroller MMIO base address into
the sunxi_gpio.h header, because the SPL routines for GPIO should be the
only one needing this address.
This is a first step towards getting rid of cpu_sun[x]i.h completely,
and allows to remove the inclusion of that file from the sunxi_gpio.h
header.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
U-Boot's generic GPIO_EXTRA_HEADER is a convenience symbol to allow code
to more easily include platform specific GPIO headers. This should not
be needed in a DM world anymore, since the generic GPIO framework
handles that nicely.
For Allwinner boards we still need to deal with non-DM GPIO in the SPL,
but this should become the exception, not the rule.
Make this more obvious by removing the definition of GPIO_EXTRA_HEADER,
and just force every legacy user of platform specific GPIO to include
the new sunxi_gpio.h header explicitly. Everyone doing so should feel
ashamed and should find a way to avoid it from now on.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Samuel Holland <samuel@sholland.org>
So far every Allwinner SoC used the same basic pincontroller/GPIO
register frame, and just differed by the number of implemented banks and
pins, plus some special functionality from time to time. However the D1
and successors use a slightly different pinctrl register layout.
Use that opportunity to drop "struct sunxi_gpio", that described that
MMIO frame in a C struct. That approach is somewhat frowned upon in the
Linux world and rarely used there, though still popular with U-Boot.
Switching from a C struct to a "base address plus offset" approach allows
to switch between the two models more dynamically, without reverting to
preprocessor macros and #ifdef's.
Model the pinctrl MMIO register frame in the usual "base address +
offset" way, and replace a hard-to-parse CPP macro with a more readable
static function.
All the users get converted over. There are no functional changes at
this point, it just prepares the stages for the D1 and friends.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Tested-by: Samuel Holland <samuel@sholland.org>
So far we were open-coding the pincontroller's GPIO output/input access
in each function using that.
Provide functions that wrap that nicely, and follow the existing pattern
(set/get_{bank,}), so users don't need to know about the internals, and
we can abstract the new D1 pinctrl more easily.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Move the existing sunxi-specific low level pinctrl routines from
arch/arm/mach-sunxi into the existing GPIO code under drivers/gpio, so
that the common code can be shared outside of arch/arm.
This also takes the opportunity to move some definitions from our
header file into the driver C file, as they are private to the driver
and are not needed elsewhere.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Tested-by: Samuel Holland <samuel@sholland.org>
The CONFIG_MACPWR Kconfig symbol is used to point to a GPIO that enables
the power for the Ethernet "MAC" (mostly PHY, really).
In the DT this is described with the phy-supply property in the MAC DT
node, pointing to a (GPIO controlled) regulator. Since we need Ethernet
only in U-Boot proper, and use a DM driver there, we should use the DT
instead of hardcoding this.
Add code to the sun8i_emac and sunxi_emac drivers to check the DT for
that regulator and enable it, at probe time. Then drop the current code
from board.c, which was doing that job before.
This allows us to remove the MACPWR Kconfig definition and the respective
values from the defconfigs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Sam Edwards <CFSworks@gmail.com>
At the moment the sun4i EMAC driver relies on hardcoded CONFIG_MACPWR
Kconfig symbols to enable potential PHY regulators. As we want to get rid
of those, we need to find the regulator by chasing up the DT.
The sun4i-emac binding puts the PHY regulator into the MDIO node, which
is the parent of the PHY device. U-Boot does not have (and does not
need) an MDIO driver, so we need to chase down the regulator through the
EMAC node: we follow the "phy-handle" property to find the PHY node,
then go up to its parent, where we find the "phy-supply" link to the
regulator. Let U-Boot find the associated regulator device, and put that
into the private device struct, so we can find and enable the regulator
at probe time, later.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Sam Edwards <CFSworks@gmail.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
The CONFIG_SATAPWR Kconfig symbol was used to point to a GPIO that
enables the power for a SATA harddisk.
In the DT this is described with the target-supply property in the AHCI
DT node, pointing to a (GPIO controlled) regulator. Since we need SATA
only in U-Boot proper, and use a DM driver for AHCI there, we should use
the DT instead of hardcoding this.
Add code to the sunxi AHCI driver to check the DT for that regulator and
enable it, at probe time. Then drop the current code from board.c, which
was doing that job before.
This allows us to remove the SATAPWR Kconfig definition and the
respective values from the defconfigs.
We also select the generic fixed regulator driver, which handles those
GPIO controlled regulators.
Please note that the OrangePi Plus is a bit special here, it's a H3
board without native SATA, but with a USB-to-SATA bridge. The DT models
the SATA power via a VBUS supply regulator, which we don't parse yet in
the USB PHY driver. Use the hardcoded CONFIG_USB3_VBUS_PIN for that
board meanwhile.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Sam Edwards <CFSworks@gmail.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
With the commit 4fcba5d556 ("regulator: implement basic reference
counter") the return value of regulator_set_enable may be EALREADY or
EBUSY for fixed/gpio regulators and may be further expanded on all
regulators.
Change to use the more relaxed regulator_set_enable_if_allowed to
continue if regulator already was enabled or disabled.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
With the commit 4fcba5d556 ("regulator: implement basic reference
counter") the return value of regulator_set_enable may be EALREADY or
EBUSY for fixed/gpio regulators and may be further expanded on all
regulators.
Change to use the more relaxed regulator_set_enable_if_allowed to
continue if regulator already was enabled or disabled.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
With the commit 4fcba5d556 ("regulator: implement basic reference
counter") the return value of regulator_set_enable may be EALREADY or
EBUSY for fixed/gpio regulators and may be further expanded on all
regulators.
Change to use the more relaxed regulator_set_enable_if_allowed to
continue if regulator already was enabled or disabled.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
This copies in some devicetree files from the official Linux kernel tree,
v6.6-rc6. It covers a board with the Allwinner T113s SoC, which shares
many devices with its RISC-V sibling, the Allwinner D1(s). This is the
reason for the core .dtsi files landing in the arch/riscv directory.
We are only adjusting the include path to accommodate for the differences
in the U-Boot build system.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Sync the devicetree files from the official Linux kernel tree, v6.6-rc6.
This is covering Allwinner SoCs with 32-bit ARM cores, minus the T113s
board and related .dtsi files, which come separately.
Only small changes: Bluetooth got enabled on the C.H.I.P., and a clock
got renamed. More interesting is the addition of a board, for which
U-Boot enablement patches are pending.
As before, this omits the non-backwards compatible changes to the R_INTC
controller, to remain compatible with older kernels.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Sync the devicetree files from the official Linux kernel tree, v6.6-rc6.
This is covering Allwinner SoCs with 64-bit ARM cores.
Only small cosmetic changes (clock name fixed), but we add the DT for
the new OrangePi Zero 3 board, for which U-Boot enablement patches are
pending.
As before, this omits the non-backwards compatible changes to the R_INTC
controller, to remain compatible with older kernels.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Enable building Pogo V4 u-boot image with LTO, which results in about 30K
reduction in size.
Rebased to latest master and resend.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The current SCIF error handling is broken for the RZ/G2L. After a break
condition has been triggered, the current code is unable to clear the
error and serial port output never resumes.
The RZ/G2L datasheet says that most error conditions are cleared by
resetting the relevant error bits in the FSR & LSR registers to zero.
To clear framing errors on SCIF ports, the invalid data also needs to be
read out of the receive FIFO.
After reviewing datasheets for RZ/G2{H,M,N,E}, R-Car Gen4, R-Car Gen3
and even SH7751 SoCs, it's clear that this is the way to clear errors
for all of these SoCs.
While we're here, annotate the handle_error() function with a couple of
comments as the reads and writes themselves don't immediately make it
clear what we're doing.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Tested-by: Chris Paterson <chris.paterson2@renesas.com> # HiHope RZ/G2M board
Tested-by: Marek Vasut <marek.vasut+renesas@mailbox.org> # R-Car H3 Salvator-XS
This patch adds ISA string to the -march to generate zbb instructions
for U-Boot binaries, along with optimized string functions introduced
from Linux kernel.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Originally, u-boot SPL will place the DTB directly after the kernel,
but the size of the kernel does not include the BSS section, This
means that u-boot SPL places the DTB in the kernel BSS section causing
the DTB to be cleared by the kernel BSS initialisation.
Moving the DTB in front of the kernel can avoid this error.
Signed-off-by: Randolph <randolph@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Fork from ae350_rv[32/64]_spl_[xip]_defconfig and
append CONFIG_SPL_LOAD_FIT_OPENSBI_OS_BOOT=y
Signed-off-by: Randolph <randolph@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
If SPL_LOAD_FIT_OPENSBI_OS_BOOT is enabled, the function
spl_invoke_opensbi should change the target OS type to IH_OS_LINUX.
OpenSBI will load the Linux image as the next boot stage.
The os_takes_devicetree function returns a value of true or false
depending on whether or not SPL_LOAD_FIT_OPENSBI_OS_BOOT is enabled.
Signed-off-by: Randolph <randolph@andestech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add condition for OpenSBI OS boot mode, by default it is not enabled.
By default, binman creates the output file u-boot.itb.
If SPL_OPENSBI_OS_BOOT is enabled, linux.itb will be created
after compilation instead of the default u-boot.itb.
Signed-off-by: Randolph <randolph@andestech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Introduce common Kconfig symbol for riscv architecture.
This symbol SPL_LOAD_FIT_OPENSBI_OS_BOOT is like falcon mode on ARM,
the Falcon boot is a shortcut boot method for SD/eMMC targets. It
skips the loading the RAM version U-Boot. Instead, it will loads
the FIT image and boots directly to Linux.
When SPL_OPENSBI_OS_BOOT is enabled, linux.itb is created after
compilation instead of the default u-boot.itb. It initialises memory
with the U-Boot SPL at the first stage, just as a normal boot process
does at the beginning. Instead of jumping to the U-Boot proper from
OpenSBI before booting the Linux kernel, the RISC-V falcon mode
process jumps directly to the Linux kernel to gain shorter booting time.
Signed-off-by: Randolph <randolph@andestech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In order to introduce the Opensbi OS boot mode, the next stage boot
image of OpenSBI should be configurable.
Signed-off-by: Randolph <randolph@andestech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Source hart information is not necessary in IPI, so we could
use single-bit-per-hart strategy to rearrange PLICSW mapping.
Bit 0 of Interrupt Pending Bits is hardwired to 0.
Therefore, we use bit 1 to send IPI to hart 0,
bit 2 to hart 1, ..., and so on.
Signed-off-by: Randolph <randolph@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Some platforms may not have any DDR memory below 4G and for such platforms
the TEXT_BASE and LOAD addresses etc are all 64 bit addresses due to
which the u-boot build fails with below error:
u-boot/arch/riscv/dts/binman.dtsi:30.14-25
Value out of range for 32-bit array element
u-boot/arch/riscv/dts/binman.dtsi:43.14-25
Value out of range for 32-bit array element
u-boot/arch/riscv/dts/binman.dtsi:44.15-26
Value out of range for 32-bit array element
FATAL ERROR: Syntax error parsing input tree
Fix by setting the address-cells property to 2 and converting load
addresses to 64 bit values.
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove dram_init_banksize() on the architecture level.
Limiting used RAM to under 4 GiB is only necessary for CPUs which have a
DMA issue. SoC specific code already exists for FU540, FU740, JH7110.
Not all RISC-V boards will have memory below 4 GiB.
A weak implementation of dram_init_banksize() exists in common/board_f.c.
See the discussion in
https://lore.kernel.org/u-boot/545fe813-cb1e-469c-a131-0025c77aeaa2@canonical.com/T/
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Fix npcm845 watchdog halt for reset function and expire function.
Reset function is restart wdt.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Reviewed-by: Stefan Roese <sr@denx.de>
For some time now running sandbox with -T produces an error:
Core: 270 devices, 95 uclasses, devicetree: board
WDT: Not starting wdt-gpio-toggle
wdt_gpio wdt-gpio-level: Request for wdt gpio failed: -16
WDT: Not starting wdt@0
MMC: mmc2: 2 (SD), mmc1: 1 (SD), mmc0: 0 (SD)
Use an unallocated GPIO to avoid this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: 1fc45d6483 ("watchdog: add pulse support to gpio watchdog driver")
Reviewed-by: Stefan Roese <sr@denx.de>
The i.MX8MP DHCOM SoM production rev.200 is populated with M24C32-D
EEPROMs which have Additional Write lockable page at separate I2C
address. Describe the page in DT to make it available.
Disable the additional page in rev.100 SoM DTO as those devices
contain EEPROM without an Additional Write lockable page.
Signed-off-by: Marek Vasut <marex@denx.de>
The ST M24C32-D behaves as a regular M24C32, except for the -D variant
which uses up another I2C address for Additional Write lockable page.
This page is 32 Bytes long and can contain additional data. Add entry
for it, so users can describe that page in DT. Note that users still
have to describe the main M24C32 area separately as that is on separate
I2C address from this page.
From Linux kernel commit:
4791146e9055 ("eeprom: at24: add ST M24C32-D Additional Write lockable page support")
Signed-off-by: Marek Vasut <marex@denx.de>
To quote the author:
This series adds some tests for various SPL load methods, with the
intent of helping debug v6 of [1]. With that in mind, notable omissions
include NAND and ROMAPI, which both lack sandbox implementations, and
OS_BOOT, which I have deferred due to its complexity. Semihosting is
also omitted, but I think we can test that with qemu.
In order to test all of these methods, we must first generate suitable
images, possibly on filesystems. While other tests have historically
generated these images using external tools (e.g. mkimage, mkfs, etc.),
I have chosen to generate them on the fly. This is for a few reasons:
- By removing external dependencies on pytest to create certain files,
the tests become self-contained. This makes them easier to iterate on
and debug.
- By generating tests at runtime, we can dynamically vary the content.
This helps detect test failures, as even if tests are loaded to the
same location, the expected content will be different.
- We are not testing the image parsers themselves (e.g.
spl_load_simple_fit or fs_read) but rather the load methods (e.g.
spl_mmc_load_image). It is unnecessary to exercise full functionality
or generate 100% correct images.
- By reducing functionality to only what is necessary, the complexity of
various formats can often be greatly reduced.
This series depends on [2-3], which are small fixes identified through
this patch set. The organization of patches in this series is as
follows:
- General fixes for bugs which are unlikely to be triggered outside of
this series
- Changes to IMX8 container images to facilitate testing
- General prep. work, particularly regarding linker issues
- The tests themselves
Passing CI at [4].
[1] https://lore.kernel.org/all/20230731224304.111081-1-sean.anderson@seco.com/
[2] https://lore.kernel.org/all/20230930204246.515254-1-seanga2@gmail.com/
[3] https://lore.kernel.org/all/20231008014748.1987840-1-seanga2@gmail.com/
[4] https://source.denx.de/u-boot/custodians/u-boot-clk/-/pipelines/18128
The i.MX93 11x11 EVK fails to boot with following error:
Model: NXP i.MX93 11X11 EVK board
DRAM: 2 GiB
Error binding driver 'imx93-adc': -96
Some drivers failed to bind
Error binding driver 'simple_bus': -96
Some drivers failed to bind
Error binding driver 'simple_bus': -96
Some drivers failed to bind
initcall sequence 00000000fffb8f28 failed at call 000000008021e0d4 (err=-96)
### ERROR ### Please RESET the board ###
That's because since commit e7ff54d963 ("imx93_evk: defconfig: add adc
support") CONFIG_ADC_IMX93 is enabled but CONFIG_ADC is not.
Fix this by enabling CONFIG_ADC in imx93_11x11_evk_defconfig.
Make sure this situation won't happen again in future i.MX93 defconfig by
making CONFIG_ADC_IMX93 depend on CONFIG_ADC.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add test for the SPI load method. This one is pretty straightforward. We
can't enable FIT_EXTERNAL with LOAD_FIT_FULL because spl_spi_load_image
doesn't know the total image size and has to guess from fdt_totalsize. This
doesn't include external data, so loading it will fail.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a test for the NOR load method. Since NOR is memory-mapped we can
substitute a buffer instead. The only major complication is testing LZMA
decompression. It's too complex to implement LZMA compression in a test, and we
have no in-tree compressor, so we just include some pre-compressed data. This
data was generated through something like
generate_data(plain, plain_size, "lzma")
cat plain.dat | lzma | hexdump -C
and was cleaned up further in my editor.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a test for loading U-Boot over TFTP. As with other sandbox net
routines, we need to initialize our packets manually since things like
net_set_ether and net_set_udp_header always use "our" addresses. We use
BOOTP instead of DHCP, since DHCP has a tag/length-based format which is
harder to parse. Our TFTP implementation doesn't define as many constants
as I'd like, so I create some here. Note that the TFTP block size is
one-based, but offsets are zero-based.
In order to avoid address errors, we need to set up/define some additional
address information settings. dram_init_banksize would be a good candidate
for settig up bi_dram, but it gets called too late in board_init_r.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a test for the MMC load method. This shows the general shape of tests
to come: The main test function calls do_spl_test_load with an appropriate
callback to write the image to the medium.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a test for spl_blk_load_image, currently used only by NVMe. Because
there is no sandbox NVMe driver, just use MMC instead. Avoid falling back
to raw images to make failures more obvious.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add some functions for creating fat/ext2 filesystems with a single file and
a test for them. Filesystems require block devices, and it is easiest to
just use MMC for this. To get an MMC, we must also pull in the test device
tree. SPL_TIMER is necessary for SPL_MMC, perhaps because it uses a timeout.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This add some basic functions to create images, and a test for said
functions. This is not intended to be a test of the image parsing
functions, but rather a framework for creating minimal images for testing
load methods. That said, it does do an OK job at finding bugs in the image
parsing directly.
Since we have two methods for loading/parsing FIT images, add LOAD_FIT_FULL
as a separate CI run.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Returning a negative value from a unit test doesn't automatically fail the
test. We have to fail an assertion. Modify the test to do so.
This now causes the test to count as a failure on VPL. This is because the
fname of SPL (and U-Boot) is generated with make_exec in os_jump_to_image.
The original name of SPL is gone, and we can't determine the name of U-Boot
from the generated name.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In order to make adding new spl unit tests easier, especially when they may
have many dependencies, add some Kconfigs for the existing image test.
Split it into the parts which are generic (such as callbacks) and the
test-specific parts.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The test devicetree is only compiled for U-Boot proper. When accessing it in
SPL we need to go up one directory.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
All "physical" addresses in SPL must be converted to virtual addresses
before access in order for sandbox to work. Add some calls to map_sysmem in
appropriate places. We do not generally call unmap_sysmem, since we need
the image memory to still be mapped when we jump to the image. This doesn't
matter at the moment since unmap_sysmem is a no-op.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Several SPL functions try to avoid performing initialization twice by
caching devices. This is fine for regular boot, but does not work with
UNIT_TEST, since all devices are torn down after each test. Add some
functions to invalidate the caches which can be called before testing these
load methods.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
If we sent a DHCP packet and get a BOOTP response from the server, we
shouldn't try to send a DHCPREQUEST packet, since it won't be DHCPACKed.
Transition straight to BIND. This is only enabled for UNIT_TEST to avoid
bloat, since I suspect the number of BOOTP servers in the wild is
vanishingly small.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When fastboot is enabled in U-Boot proper and SPL_NET is enabled, we will
try to (unsuccessfully) reference it in SPL. Fix these linker errors by
conditioning on SPL_UDP/TCP_FUNCTION_FASTBOOT.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add various defines which are not necessary for reading/writing
filesystems, but which are useful for creating them. These mostly come from
Linux v6.5-rc2 (what I had checked out).
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If EXT4_WRITE is enabled, write capabilities will be compiled into SPL, but
not CRC16. Add an option to enable CRC16 to avoid linker errors.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Don't bother compiling the sandbox filesystem in SPL for now, as it is not
needed.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
lib/acpi/acpigen.o is only compiled into SPL when SPL_ACPIGEN is enabled.
Update several files which reference these functions accordingly.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Sandbox unit tests in U-Boot proper load a test device tree to have some
devices to work with. In order to do the same in SPL, we must enable
SPL_OF_REAL. However, we already have SPL_OF_PLATDATA enabled. When
generating platdata from a devicetree, it is expected that we will not need
devicetree access functions (even though SPL_OF_CONTROL is enabled). This
expectation does not hold for sandbox, so allow user control of
SPL_OF_REAL.
There are several places in the tree where conditions involving OF_PLATDATA
or OF_REAL no longer function correctly when both of these options can be
selected at the same time. Adjust these conditions accordingly.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Make sure we have an IMX header before calling spl_load_imx_container,
since if we don't it will fail with -ENOENT. This allows us to fall back to
legacy/raw images if they are also enabled.
This is a functional change, one which likely should have been in place
from the start, but a functional change nonetheless. Previously, all
non-IMX8 images (except FITs without FIT_FULL) would be optimized out if
the only image load method enabled supported IMX8 images. With this change,
support for other image types now has an effect.
There are seven boards with SPL_LOAD_IMX_CONTAINER enabled: three with
SPL_BOOTROM_SUPPORT:
imx93_11x11_evk_ld imx93_11x11_evk imx8ulp_evk
and four with SPL_MMC:
deneb imx8qxp_mek giedi imx8qm_mek
All of these boards also have SPL_RAW_IMAGE_SUPPORT and
SPL_LEGACY_IMAGE_FORMAT enabled as well. However, none have FIT support
enabled. Of the six load methods affected by this patch, only SPL_MMC and
SPL_BOOTROM_SUPPORT are enabled with SPL_LOAD_IMX_CONTAINER.
spl_romapi_load_image_seekable does not support legacy or raw images, so
there is no growth. However, mmc_load_image_raw_sector does support loading
legacy/raw images. Since these images could not have been booted before, I
have disabled support for legacy/raw images on these four boards. This
reduces bloat from around 800 bytes to around 200.
There are no in-tree boards with SPL_LOAD_IMX_CONTAINER and AHAB_BOOT both
enabled, so we do not need to worry about potentially falling back to
legacy images in a secure boot scenario.
Future work could include merging imx_container.h with imx8image.h, since
they appear to define mostly the same structures.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
These error messages are missing newlines. Add them.
Fixes: 6e81ca220e ("imx: parse-container: Use malloc for container processing")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
We should load images to their destination, not their entry point.
Fixes: 7b86cd4274 ("imx8: support parsing i.MX8 Container file")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
The entry point is not always the same as the load address. Use the value
of the entry property if it exists.
Fixes: 8a9dc16e4d ("spl: Add full fitImage support")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
spl_image_info.name contains a reference to legacy_img_hdr. If we allocate
the latter on the stack, it will be clobbered after we return. This was
addressed for NAND back in 06377c5a1f ("spl: spl_legacy: Fix NAND boot on
OMAP3 BeagleBoard"), but that commit didn't fix NOR.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
On non-arm architectures, _image_binary_end is defined as a ulong and not a
char[]. Take the address of it when accessing it, which is correct for
both.
Fixes: 1b8a1be1a1 ("spl: spl_legacy: Fix spl_end address")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This check breaks small partitions (under 1024 blocks) because part_length
is in units of part.blksz and not bytes. Given the purpose of this
function, we really want to make sure the partition is SUPERBLOCK_START +
SUPERBLOCK_SIZE (2048) bytes so we can call ext4_read_superblock without
error.
The obvious solution is to convert callers from things like
ext4fs_mount(part_info.size)
to
ext4fs_mount(part_info.size * part_info.blksz);
However, I'm not really a fan of the bloat that would cause, especially
since the error is now suppressed. I think the best course of action here
is to just revert the patch.
This reverts commit 9905cae65e.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
MMC devices do not have uclass platdata containing blk_descs, only their
child block devices do. Fortunately, we have a function just for this
purpose. This fixes subsequent calls to spl_mmc_load.
Fixes: bf28d9a659 ("spl: mmc: Use correct MMC device when loading image")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Implement the 'getprisec' subcommand of 'bmode' command for i.MX8M by
reading out the ROM log events. This event is set by the BootROM if it
switched to the secondary copy due to primary copy being corrupted.
Signed-off-by: Fedor Ross <fedor.ross@ifm.com>
Signed-off-by: Marek Vasut <marex@denx.de>
In case of a secondary image boot from the user area of an eMMC device,
the correct offset must be calculated. The offset is fused in the fuse
IMG_CNTN_SET1_OFFSET of the i.MX8M Nano and Plus. The calculation of the
offset is described in the reference manual (IMX8MNRM Rev. 2, 07/2022
and IMX8MPRM Rev. 1, 06/2021):
The fuse IMG_CNTN_SET1_OFFSET (0x490[22:19]) is defined as follows:
* Secondary boot is disabled if fuse value is bigger than 10,
n = fuse value bigger than 10.
* n == 0: Offset = 4MB
* n == 2: Offset = 1MB
* Others & n <= 10 : Offset = 1MB*2^n
Signed-off-by: Fedor Ross <fedor.ross@ifm.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Factor out parsing of ROM log in function spl_mmc_emmc_boot_partition().
This can be helpful to detect a secondary image boot without fiddling
around with MMC partitions. This way for example, U-Boot is able to
detect a secondary image boot and can enter some fallback scenario like
starting a recovery mode.
Signed-off-by: Fedor Ross <fedor.ross@ifm.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Introduce two new weak functions, arch_spl_mmc_get_uboot_raw_sector() and
board_spl_mmc_get_uboot_raw_sector(), each of which can be overridden at
a matching level, that is arch/ and board/ , in addition to the existing
weak function spl_mmc_get_uboot_raw_sector().
This way, architecture code can define a default architecture specific
implementation of arch_spl_mmc_get_uboot_raw_sector(), while the board
code can override that using board_spl_mmc_get_uboot_raw_sector() which
takes precedence over the architecture code. In some sort of unlikely
special case where code has to take precedence over board code too, the
spl_mmc_get_uboot_raw_sector() is still left out to be a weak function,
but it should be unlikely that this is ever needed to be overridden.
Signed-off-by: Marek Vasut <marex@denx.de>
i.MX93 11x11 EVK fails to boot:
U-Boot SPL 2023.10-00558-g65b9b3462bec-dirty (Oct 03 2023 - 17:40:10 +0200)
SOC: 0xa0009300
LC: 0x40010
M33 prepare ok
Normal Boot
Trying to boot from BOOTROM
Boot Stage: Primary boot
image offset 0x8000, pagesize 0x200, ivt offset 0x0
Load image from 0x44400 by ROM_API
NOTICE: BL31: v2.8(release):android-13.0.0_2.0.0-0-ge4b2dbfa52f5
NOTICE: BL31: Built : 17:52:46, Sep 28 2023
That's because commit 9e644284ab ("dm: core: Report
bootph-pre-ram/sram node as pre-reloc after relocation"):
"[This] changes behavior of what nodes are bound in the U-Boot
proper pre-relocation phase. Change to bootph-all or add
bootph-some-ram prop to restore prior behavior."
Fix this by adding bootph-some-ram prop as suggested by the commit
above.
Fixes: 9e644284ab ("dm: core: Report bootph-pre-ram/sram node as pre-reloc after relocation")
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The Renesas RZ/G2L SMARC Evaluation Board Kit consists of the RZ/G2L
System-on-Module (SOM) based on the R9A07G044L2 SoC, and a common SMARC
carrier board.
The ARM TrustedFirmware code for the Renesas RZ/G2L SoC family passes a
devicetree blob to the bootloader as an argument in the same was
previous R-Car gen3/gen4 SoCs. This blob contains a compatible string
which can be used to identify the particular SoC we are running on and
this is used to select the appropriate device tree to load.
The configuration renesas_rzg2l_smarc_defconfig is added to support
building for this target. In the future this defconfig will be extended
to support other SoCs and evaluation boards from the RZ/G2L family.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The Renesas RZ/G2L SMARC Evaluation Board Kit consists of the RZ/G2L
System-on-Module (SOM) based on the R9A07G044L2 SoC, and a common SMARC
carrier board.
This patch is based on the corresponding Linux v6.5 device tree
(commit 52e12027d50affbf60c6c9c64db8017391b0c22e).
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The memory map for the RZ/G2L family differs from that of previous R-Car
Gen3/Gen4 SoCs.
A high level memory map can be seen in figure 5.2 (section 5.2.1) of the
RZ/G2L data sheet rev 1.30 published May 12, 2023. A summary is included
here (note that this is a 34-bit address space):
* 0x0_0000_0000 - 0x0_0002_FFFF SRAM area
* 0x0_0003_0000 - 0x0_0FFF_FFFF Reserved area
* 0x0_1000_0000 - 0x0_1FFF_FFFF I/O register area
* 0x0_2000_0000 - 0x0_2FFF_FFFF SPI Multi area
* 0x0_3000_0000 - 0x0_3FFF_FFFF Reserved area
* 0x0_4000_0000 - 0x1_3FFF_FFFF DDR area (4 GiB)
* 0x1_4000_0000 - 0x3_FFFF_FFFF Reserved area
Within the DDR area, the first 128 MiB are reserved by TrustedFirmware.
The region from 0x43F00000 to 0x47DFFFFF inclusive is protected for use
in TrustedFirmware/OP-TEE, but all other memory is included in the
memory map. This reservation is the same as used in R-Car
Gen3/Gen4 and RZ/G2{H,M,N,E} SoCs.
DRAM information is initialised based on the data in the fdt.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The ARM TrustedFirmware code for the Renesas RZ/G2L SoC family passes a
devicetree blob to the bootloader as an argument in the same was
previous R-Car Gen3/Gen4 SoCs. This blob contains a compatible string
which can be used to identify the particular SoC we are running on.
We do this as reading the DEVID & PRR registers from u-boot is not
sufficient to differentiate between the R9A07G044L (RZ/G2L) and
R9A07G044C (RZ/G2LC) SoCs. An additional read from offset 0x11861178 is
needed but this address is in the OTP region which can only be read from
the secure world (i.e. TrustedFirmware). So we have to rely on
TrustedFirmware to determine the SoC and pass this information to u-boot
via an fdt blob.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Move the assignment of priv->quirks earlier in the function. This allows
us to drop the quirks local variable and makes it easier to maintain
clean error handling when we add RZ/G2L support in the next patch.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add USB0 OTG support.
Currently, the USB0 OTG nodes are not enabled in the Linux kernel
devicetree.
For this reason, enable the USB0 OTG nodes inside imx8mp-evk-u-boot.dtsi
for now.
Also select several useful options such as USB gadget and fastboot.
Tested by running "ums 0 mmc 2".
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
The GPIO3 has to be available early during U-Boot proper start up for
DRAM size detect to work correctly. The GPIO3 is currently available in
SPL and late in U-Boot proper, which is insufficient. Add the missing
bootph-all to make the GPIO3 available also early in U-Boot proper.
Signed-off-by: Marek Vasut <marex@denx.de>
Unselect CONFIG_CONSOLE_MUX to fix the following
error for the input, output and error interfaces:
U-Boot 2023.10 (Oct 03 2023 - 21:23:18 -0300)
...
In: No input devices available!
Out: No output devices available!
Err: No error devices available!
Net: eth0: ethernet@30be0000
Hit any key to stop autoboot: 0
Signed-off-by: Fabio Estevam <festevam@denx.de>
The xfi3 target has been removed by commit 539fba2c10 ("arm:
Remove xfi3 board"), but it missed to remove an entry from the
mxs Kconfig.
Remove it.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Commit 68dcbdd594 ("ARM: imx: Add weak default reset_cpu()") caused
the 'reset' command in U-Boot to not cause a board reset.
Fix it by switching to the watchdog driver model via sysreset, which
is the preferred method for implementing the watchdog reset.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Commit 68dcbdd594 ("ARM: imx: Add weak default reset_cpu()") caused
the 'reset' command in U-Boot to not cause a board reset.
Fix it by switching to the watchdog driver model via sysreset, which
is the preferred method for implementing the watchdog reset.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
SPDX-License tag is missing and checkpatch complains about it.
Add the SPDX-License tag using the same one from imx7d-sdb.dts.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
The current imx8mp-dhcom-som.dtsi describes production rev.200 SoM,
add DT overlay which reinstates rev.100 SoM description to permit
prototype rev.100 SoMs to be used until they get phased out.
Signed-off-by: Marek Vasut <marex@denx.de>
In case the i.MX8MP DHCOM rev.100 has been populated on the PDK3
carrier board, the on-SoM PHY PHYAD1 signal has been pulled high
by the carrier board and changed the PHY MDIO address from 5 to 7.
This has been fixed on production rev.200 SoM by additional buffer
on the SoM PHYAD/LED signals, remove the workaround.
Signed-off-by: Marek Vasut <marex@denx.de>
The current imx8mp-dhcom-som.dtsi describes prototype rev.100 SoM,
update the DT to describe production rev.200 SoM which brings the
following changes:
- Fast SoC GPIOs exposed on the SoM edge connector
- Slow GPIOs like component resets moved to I2C GPIO expander
- ADC upgraded from TLA2024 to ADS1015 with conversion interrupt
- EEPROM size increased from 256 B to 4 kiB
Signed-off-by: Marek Vasut <marex@denx.de>
Add DT overlays to support additional DH i.MX8MP DHCOM SoM 660-100
population options with 1x or 2x RMII PHY mounted on PDK2 or PDK3
carrier boards.
Use SPL DTO support to apply matching SoM specific DTO to cater
for the SoM differences. Remove ad-hoc patching of control DT from
fdtdec_board_setup().
Signed-off-by: Marek Vasut <marex@denx.de>
Add board-specific function used to indicate whether a DTO from fitImage
configuration node 'fdt' property DT and DTO list should be applied onto
the base DT or not applied.
This is useful in case of DTOs which implement e.g. different board revision
details, where such DTO should be applied on one board revision, and should
not be applied on another board revision.
Signed-off-by: Marek Vasut <marex@denx.de>
The current code works by sheer coincidence, because (see HABv4 API
documentation, section 3.4) the RVT authenticate_image call updates
the size that is passed in with the actual size ROM code pulls from
IVT/CSF . So if the input size is larger, that is "fine" . Pass in
size instead to make this really correct.
Signed-off-by: Marek Vasut <marex@denx.de>
- Add some dependencies to CMD_DDR3 as this is only valid on some
platforms (which tend to select it as well).
- The proper gate for going in to cmd/ti is not
CONFIG_TI_COMMON_CMD_OPTIONS as nothing under there is controlled by
that symbol but the general TI architecture options.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Generally we just drop the #ifdef CONFIG_SYS_LONGHELP and endif lines
and use U_BOOT_LONGHELP to declare the same variable name as before
- In a few places, either rename the variable to follow convention or
introduce the variable as it was being done inline before.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In order to be able to discard unused long help texts without further
linker lists, add a macro for defining the long help messages which uses
__maybe_unused. This allows us to discard them as unreferenced as part
of the link.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If the data version field of the EEPROM is not supported, provide a hexdump
of the data.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The different implementations of the mac command have board or vendor
specific sub-commands.
Add the command definition specific to the VisionFive 2 board.
Don't call cmd_usage() directly but return CMD_RET_USAGE instead.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The different implementations of the mac command have board or vendor
specific sub-commands.
Add the command definition specific to the SiFive HiFive Unmatched board.
Don't call cmd_usage() directly but return CMD_RET_USAGE instead.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
CONFIG_SYS_LONGHELP=n we want to reduce the size of the U-Boot binary.
The long text should be reduced to and empty string in this case.
There is not need to call cmd_usage() directly. It is sufficient to
return CMD_RET_USAGE.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Board specific implementations of the 'mac' command differ concerning the
supported sub-commands.
Move the Freescale specific mac command definition to the board code.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This driver adds support for the gpio features of the GPIO/PFC module in
the Renesas RZ/G2L (R9A07G044) SoC.
The new `rzg2l-pfc-gpio` driver is bound to the same device tree node as
the `rzg2l-pfc-pinctrl` driver as the same hardware block provides both
GPIO and pin multiplexing features.
This patch is based on the corresponding Linux v6.5 driver
(commit 52e12027d50affbf60c6c9c64db8017391b0c22e).
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
This driver adds support for the pinctrl features of the GPIO/PFC module
in the Renesas RZ/G2L (R9A07G044) SoC.
A multi-function `rzg2l-pfc` driver is defined for UCLASS_NOP, which
binds the `rzg2l-pfc-pinctrl` UCLASS_PINCTRL driver dynamically. We also
define common macros and functions for the PFC in <renesas/rzg2l-pfc.h>.
This makes it easy to add an additional UCLASS_GPIO driver for the GPIO
functionality of this module in a follow-up patch.
This patch is based on the corresponding Linux v6.5 driver
(commit 52e12027d50affbf60c6c9c64db8017391b0c22e).
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
On the Renesas RZ/G2L SoC family, valid GPIO numbers are not contiguous.
This is determined by the device tree, where a fixed number of bits are
used for the 'pin' number within a 'port', even though not all ports
have the same number of pins. The device tree can't be changed here
without breaking backwards compatibility in Linux, which we don't want
to do.
To avoid printing a status for each of these invalid GPIO numbers when
a user executes `gpio status -a`, we allow gpio_get_function() to return
-ENOENT when the given offset does not refer to a valid GPIO pin and we
skip printing anything if this occurs.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
This driver provides clock and reset control for the Renesas R9A07G044L
(RZ/G2L) and R9A07G044C (RZ/G2LC) SoC. It consists of two parts:
* driver code which is applicable to all SoCs in the RZ/G2L family.
* static data describing the clocks and resets which are specific to the
R9A07G044{L,C} SoCs. The identifier r9a07g044 (without a final letter)
is used to indicate that both SoCs are supported.
clk_set_rate() and clk_get_rate() are implemented only for the clocks
that are actually used in u-boot.
The CPG driver is marked with DM_FLAG_PRE_RELOC to ensure that its bind
function is called before the SCIF (serial port) driver is probed. This
is required so that we can de-assert the relevant reset signal during
the serial driver probe function.
This patch is based on the corresponding Linux v6.5 driver
(commit 52e12027d50affbf60c6c9c64db8017391b0c22e).
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
If we attempt to compile serial_sh.c for a system which lacks HSCIF
support (e.g. R8A7740), we see the following compilation error:
In file included from drivers/serial/serial_sh.c:20:
drivers/serial/serial_sh.c: In function ‘sh_serial_init_generic’:
drivers/serial/serial_sh.h:429:35: warning: implicit declaration of function ‘sci_HSSRR_out’; did you mean ‘sci_SCSCR_out’? [-Wimplicit-function-declaration]
429 | #define sci_out(port, reg, value) sci_##reg##_out(port, value)
| ^~~~
drivers/serial/serial_sh.c:62:17: note: in expansion of macro ‘sci_out’
62 | sci_out(port, HSSRR, HSSRR_SRE | HSSRR_SRCYC8);
| ^~~~~~~
To fix this, only try to support access to the HSSRR register for SoCs
where it actually exists.
Support for the RZ/G2L will be introduced in following patches, which
selects CONFIG_RCAR_64 but does not have HSCIF interfaces, so check for
CONFIG_RCAR_GEN2 || CONFIG_RCAR_GEN3 || CONFIG_RCAR_GEN4 to determine if
HSCIF is present.
Fixes: bbe36e29ca ('serial: sh: Add HSCIF support for R-Car SoC')
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Cc: Hai Pham <hai.pham.ud@renesas.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Current codes only ennable the PER clock. However on iMX8 the LPUART
also needs IPG clock which is an LPCG. Should not depend on the default
LPCG setting.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
When CLK is enabled, get_lpuart_clk_rate() needs to get a per clock of
lpuart, so that add a per clock for lpuart1.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Add i.MX93 CCF driver support.
Modifed from Linux Kernel v6.5-rc2 and adapted for U-Boot.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
The USB_PWR signal operation is not reliable on this DWC3 controller
instance in case the signal is active high. Switch to GPIO control,
which always behaves correctly. Perform the change in u-boot extras
until this hits Linux upstream.
Signed-off-by: Marek Vasut <marex@denx.de>
The RD-AC5X doesn't make use of EFI or SMBIOS. Recently we started seeing
boot failures such as
WARNING: SMBIOS table_address overflow 27f60f020
Failed to write SMBIOS table
initcall failed at event 10/(unknown) (err=-22)
### ERROR ### Please RESET the board ###
The error is because the physical address of the RAM on the AC5X SoC is
above the 32GiB boundary. As we don't need SMBIOS or EFI this can be
safely disabled.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Handle 2GBit memory size value "2" from tlv eeprom on ddr
initialisation, to support SoMs with 512MB ddr memory.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Extend the existing tlv vendor extension used for ram size by one byte to
also store the number of ddr channels.
The length of the tlv entry can indicate whether the new information is
present. If not default to single channel.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This reverts commit 5c1c6b7306. The reason
for switching to i2c-gpio was due to an issue we were seeing in the
Linux kernel where the CPU would lock up on certain adverse I2C bus
conditions. We were never able to reproduce the lockup in U-Boot but
assumed that was probably just luck.
Since then we have discovered that the lock up was due to the I2C
transaction offload engine in the I2C controller not coping with the
adverse bus conditions (basically it thinks there's another master and
waits for a STOP condition that never comes). U-Boot doesn't use the I2C
offload feature so is not susceptible to the lockup.
We can therefore safely return to using the built-in I2C controller.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The x240 doesn't make use of EFI or SMBIOS. Recently we started seeing
boot failures such as
WARNING: SMBIOS table_address overflow 23f60c020
Failed to write SMBIOS table
initcall failed at event 10/(unknown) (err=-22)
### ERROR ### Please RESET the board ###
The error is because the physical address of the RAM on the AC5X SoC is
above the 32GiB boundary. As we don't need SMBIOS or EFI this can be
safely disabled.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Starting with PCB revision 3 we can safely make use of higher RAM
frequency again. Make use of the EEPROM detection to determine the
revision and use the updated RAM timings for new SoMs.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
Tested-by: Yannic Moog <y.moog@phytec.de>
Add EEPROM detection initialisation for phyCORE-i.MX8MM and
print SoM information during boot when successful.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
Tested-by: Yannic Moog <y.moog@phytec.de>
Add helper function to read out the PCB revision of a PHYTEC SoM.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
Tested-by: Yannic Moog <y.moog@phytec.de>
Due to PCB layout constraints in PCB revisions until including 1549.2,
a RAM frequency of 2 GHz can cause rare instabilities. Set the RAM
frequency to 1.5 GHz to achieve a stable system under all conditions.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
Tested-by: Yannic Moog <y.moog@phytec.de>
Add imx8m specific detection part. Which includes checking the
EEPROM data for article number options.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
Tested-by: Yannic Moog <y.moog@phytec.de>
Recent shipped PHYTEC SoMs come with an i2c EEPROM containing
information about the hardware such as board revision and variant.
This can be used for RAM detection and loading device tree overlays
during kernel start.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
Tested-by: Yannic Moog <y.moog@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add hook in sata_mv probe to enable bootstd bootdev.
Note: bootdev_setup_for_sibling_blk() invocation is a noop if bootsd is
not enabled for ahci sata yet.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
ZyXEL NSA325 specifications:
Marvell Kirkwood 88F6282 SoC
1.6 GHz CPU
1x GBE LAN port (Marvell MV88E1318)
512 MB RAM
128 MB Eon NAND, SLC
I2C
1x USB 3.0 (on PCIe bus)
2x USB 2.0
2x SATA (hot swap slots)
Serial console
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The cn9130.dtsi defines a pinctrl node for SPI1 (until recently it was
mislabeled as spi0). Use this instead of having a duplicate definition
with a different label.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The CN9130-DB uses the SPI1 interface but had the pinctrl node labelled
as "cp0_spi0_pins". Use the label "cp0_spi1_pins" and update the node
name to "cp0-spi-pins-1" to avoid confusion with the pinctrl options for
SPI0.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The 2nd HD is not enabled in U-Boot on the D-Link DNS325. This patch
sets the responsible GPIO to high, enabling the drive.
Suggested-by: Peter Granilla
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tony Dinh <mibodhi@gmail.com>
When using a list of writeable variables, the initial values come
from the built-in default environment since commit 5ab8105836 ("env:
Complete generic support for writable list").
Remove unnecessary misuse of CONFIG_ENV_IS_NOWHERE as default environment.
Based on the fix done by commit b16fd7f75f ("imx6q: acc: Remove misuse
of env is nowhere driver").
Signed-off-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Since commit 4fcba5d556 ("regulator: implement basic reference
counter") the return value of regulator_set_enable() may be EALREADY or
EBUSY for fixed/GPIO regulators.
Switch to using the more relaxed regulator_set_enable_if_allowed() to
continue if regulator already was enabled or disabled.
This fixes the following error when running the 'ums' command:
=> ums 0 mmc 0
UMS: LUN 0, dev mmc 0, hwpart 0, sector 0x0, count 0xece000
Error enabling VBUS supply
g_dnl_register: failed!, error: -114
g_dnl_register failed
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Use dev_ofnode() to retrieve the USB node pointer from the udevice
structure.
This fixes the following build error:
drivers/usb/host/ehci-mxs.c:143:38: error: 'struct udevice' has no member named 'node_'
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Extend the padding process of u-boot-nand.imx target by adding 10k bytes
of zeros to the end of the binary using the 'dd' command.
The existing padding method did not generate a functional binary,
as discussed in more detail in this thread [1]. Instead, we adopt the
end-padding calculation method documented in 'board/doc/colibri_imx7.rst'
as a reference, which is relevant for iMX7 with NAND storage.
Adding 10k bytes of zeros provides an approximate value that makes the
proper padding for these NAND devices.
[1] https://lore.kernel.org/all/CAC4tdFUqffQzRQFv5AGe_xtbFy1agr2SEpn_FzEdexhwjdryyw@mail.gmail.com/
Signed-off-by: Hiago De Franco <hiago.franco@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add detection of eMMC vs NAND devices on the Colibri iMX7
board. A GPIO is configured to detect the presence of an on-board resistor
that is configured differently based on the flash memory used. Depending on
the detection result, the 'variant' environment variable is set to '-emmc'
or cleared, indicating the type of storage device.
This enhancement improves variant detection during system initialization
through USB recovery mode, where U-Boot is loaded directly to RAM. This
allows variant detection for an accurate device tree selection.
Signed-off-by: Hiago De Franco <hiago.franco@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Update lpddr4 configuration and training using updated spreadsheet and
tools from NXP using data from previous spreadsheet and verified
toward datasheet:
- MX8M_Mini_LPDDR4_RPA_v22.xlsx
- mscale_ddr_tool_v3.31_setup.exe
The most relevant update is related to errata ERR050805:
"DRAM: Controller automatic derating logic may not work when
the LPDDR4 memory temperature is above 85 °C at initialization"
Other relevant fixes:
- DRAMTMG7 register: corrected calculation of T_CKPDX parameter
(equal to tCKCKEH for LPDDR4)
- RANKCTL register: corrected calculations for ODTLon and ODTLoff
to follow the JEDEC specification
- ADDRMAP7 register: added support for 17-row devices
As per errata ERR050805:
An issue exists with the automatic derating logic of the DDR
controller that only samples the LPDDR4 MR4 register when the
Temperature Update Flag (TUF) field (MR4[7] ) is 1’b1. If the
LPDDR4 memory is initialized and starts operation above 85 °C
(MR4[2:0] > 3’b011), the MR4 Temperature Update Flag (TUF) will
not be set. The DDR Controller will therefore not automatically
adjust the memory refresh rate or de-rate memory timings based
on the LPDDR4 memory temperature. This may cause the controller
incorrectly setting the refresh period, potentially cause the
LPDDR4 memory losing data contents and lead to possible data
integrity issues above 85 °C.
Errata provides three possible workaround options, while option 2
is the most reasonable:
Disable the automatic derating logic of the DDR controller and
apply fixed x2 refresh rate (0.5x refresh). This option is
suitable for designs that are expected to boot at or above 85 °C
and memory’s MR4[2:0] (Refresh Rate) DOES NOT report the following
conditions:
3b101: 0.25x refresh, no de-rating
3b110: 0.25x refresh, with de-rating
3b111: SDRAM High temperature operating limit exceeded
[1]: https://www.nxp.com/docs/en/errata/IMX8MM_0N87W.pdf
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
When built with CONFIG_IMX_HAB, the full FIT image, including stuff
tacked on beyond the end of the fdt structure, is expected to be (fdt
size rounded up to 0x1000 boundary)+CONFIG_CSF_SIZE.
Now, when the FIT image is loaded from a storage device, it doesn't
really matter that the flash.bin that gets written to target isn't
quite that big - we will just load some garbage bytes that are never
read or used for anything. But when flash.bin is uploaded via uuu,
it's important that we actually serve at least as many bytes as the
target expects, or we will hang in rom_api_download_image().
Extend the logic in the csf.sh script so that the csf blob is padded
to CONFIG_CSF_SIZE minus the size of the IVT header.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
These IS_ENABLED(CONFIG_SPL_LOAD_FIT) cases can no longer be reached,
and thus get_fit_image_size() is also redundant.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Currently, spl_imx_romapi uses a somewhat tricky workaround for the
fact that a FIT image with external data doesn't directly allow one to
know the full size of the file: It does a dummy spl_load_simple_fit(),
having the ->read callback remember the largest offset requested, and
then does a last call to rom_api_download_image() to fetch the
remaining part of the full FIT image.
We can avoid that by just keeping track of how much we have downloaded
already, and if the ->read() requests something outside the current
valid buffer, fetch up to the end of the current request.
The current method also suffers from not working when CONFIG_IMX_HAB
is enabled: While in that case u-boot.itb is not built with external
data, so the fdt header does contain the full size of the dtb
structure. However, it does not account for the extra CONFIG_CSF_SIZE
added by board_spl_fit_size_align(). And also, the data it hands out
during the first dummy spl_load_simple_fit() is of course garbage, and
wouldn't pass the verification.
So we really need to call spl_load_simple_fit() only once, let that
figure out just how big the FIT image is (including whatever data, CSF
or "ordinary" external data, has been tacked on beyond the fdt
structure), and always provide valid data from the ->read callback.
This only affects the CONFIG_SPL_LOAD_FIT case - I don't have any
hardware or experience with the CONFIG_SPL_LOAD_IMX_CONTAINER case, so
I leave that alone for now.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The hab signing script doc/imx/habv4/csf_examples/mx8m/csf.sh does
fdtget -t x u-boot.dtb /binman/imx-boot/uboot offset
to figure out the offset of u-boot.itb inside flash.bin. That works
fine for imx8mm, imx8mn, imx8mq, but fails for imx8mp because in that
case 'uboot' is merely a label and not actually the node name.
Homogenize these cases and make imx8mp the same as the other imx8m*
variants. The binman type is explicitly given and no longer derived
from the node name, and the csf.sh script will work for all four SOCs.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Drop unused code related to CONFIG_TDX_EASY_INSTALLER, that existed only on
toradex downstream branch.
Signed-off-by: Hiago De Franco <hiago.franco@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The SPL authenticates image starting from CONFIG_SPL_LOAD_FIT_ADDRESS
address, update the csf_fit.txt to match.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
If optee is detected configure it in the Linux device-tree:
- add /firmware/optee node
- add /reserved-memory nodes for optee_core and optee_shm
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Move the crypto and sec_jr* nodes from board-specific
u-boot.dtsi files into the common files. Additionally protect the
nodes with ifdef CONFIG_FSL_CAAM as they don't serve any purpose if
that is not enabled.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
There is no need to include the firmware/optee node if the optee
driver is not enabled.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Move the firmware/optee node to the common imx8mp-u-boot.dtsi and
protect it with an ifdef CONFIG_OPTEE as it is a meaningless node
without the optee driver enabled.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Move the firmware/optee node to the common imx8mm-u-boot.dtsi and
protect it with an ifdef CONFIG_OPTEE as it is a meaningless node
without the optee driver enabled.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Enable USB SDP SPL aka serial downloader recovery mode support.
While at it also enable fastboot support which may be used to
subsequently load further stages like a Toradex Easy Installer FIT
image.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Update the imx8mp-venice-gw74xx for revB:
- add CAN1
- add TIS-TPM on SPI2
- add FAN controller
- fix PMIC I2C bus (revA PMIC I2C was non-functional so no need for
backward compatible option)
- M2 socket GPIO's moved
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The Gateworks imx8mm-venice-gw7905-0x consists of a SOM + baseboard.
The GW700x SOM contains the following:
- i.MX8M Mini SoC
- LPDDR4 memory
- eMMC Boot device
- Gateworks System Controller (GSC) with integrated EEPROM, button
controller, and ADC's
- RGMII PHY
- PMIC
- SOM connector providing:
- FEC GbE MII
- 1x SPI
- 2x I2C
- 4x UART
- 2x USB 2.0
- 1x PCI
- 1x SDIO (4-bit 3.3V)
- 1x SDIO (4-bit 3.3V/1.8V)
- GPIO
The GW7905 Baseboard contains the following:
- GPS
- microSD
- off-board I/O connector with I2C, SPI, GPIO
- EERPOM
- PCIe clock generator
- 1x full-length miniPCIe socket with PCI/USB3 (via mux) and USB2.0
- 1x half-length miniPCIe socket with USB2.0 and USB3.0
- USB 3.0 HUB
- USB Type-C with USB PD Sink capability and peripheral support
- USB Type-C with USB 3.0 host support
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The Gateworks imx8mp-venice-gw73xx-2x consists of a SOM + baseboard.
The GW702x SOM contains the following:
- i.MX8M Plus SoC
- LPDDR4 memory
- eMMC Boot device
- Gateworks System Controller (GSC) with integrated EEPROM, button
controller, and ADC's
- PMIC
- SOM connector providing:
- eQoS GbE MII
- 1x SPI
- 2x I2C
- 4x UART
- 2x USB 3.0
- 1x PCI
- 1x SDIO (4-bit 3.3V)
- 1x SDIO (4-bit 3.3V/1.8V)
- GPIO
The GW73xx Baseboard contains the following:
- 1x RJ45 GbE (eQoS from SOM)
- 1x RJ45 GbE (PCI)
- off-board I/O connector with MIPI-CSI (3-lane), MIPI-DSI (4-lane),
- off-board I/O connector with RS232/RS485
- off-board I/O connector with SPI
- off-board I/O connector with I2C, UART, and GPIO
I2C, I2S and GPIO
- microSD (1.8V/3.3V)
- GPS
- Accelerometer
- EERPOM
- USB 3.0 Hub
- Front Panel bi-color LED
- re-chargeable battery (for RTC)
- PCIe clock generator
- PCIe switch
- on-board 802.11abgnac 1x1 WiFi and Bluetooth 5.2
- 1x USB Type-A host socket with USB 3.0 support
- 1x USB OTG with USB 2.0 support
- 2x MiniPCIe socket with PCI and USB 2.0
- 1x MiniPCIe socket with SIM, PCI/USB 3.0 (mux), and USB 2.0
- Wide range DC input supply
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The Gateworks imx8mp-venice-gw72xx-2x consists of a SOM + baseboard.
The GW702x SOM contains the following:
- i.MX8M Plus SoC
- LPDDR4 memory
- eMMC Boot device
- Gateworks System Controller (GSC) with integrated EEPROM, button
controller, and ADC's
- PMIC
- SOM connector providing:
- eQoS GbE MII
- 1x SPI
- 2x I2C
- 4x UART
- 2x USB 3.0
- 1x PCI
- 1x SDIO (4-bit 3.3V)
- 1x SDIO (4-bit 3.3V/1.8V)
- GPIO
The GW72xx Baseboard contains the following:
- 1x RJ45 GbE (eQoS from SOM)
- 1x RJ45 GbE (PCI)
- off-board I/O connector with MIPI-CSI (3-lane), MIPI-DSI (4-lane),
- off-board I/O connector with RS232/RS485
- off-board I/O connector with SPI
- off-board I/O connector with I2C, UART, and GPIO
I2C, I2S and GPIO
- microSD (1.8V/3.3V)
- GPS
- Accelerometer
- EERPOM
- USB 3.0 Hub
- Front Panel bi-color LED
- re-chargeable battery (for RTC)
- PCIe clock generator
- PCIe switch
- 1x USB Type-A host socket with USB 3.0 support
- 1x USB OTG with USB 2.0 support
- 1x MiniPCIe socket with PCI and USB 2.0
- 1x MiniPCIe socket with SIM, PCI/USB 3.0 (mux), and USB 2.0
- Wide range DC input supply
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Linux microPlatform uses an rngb device in optee-os in boot scheme
SPL -> OPTEE -> U-Boot. To make rngb available for optee-os, enable
it in SPL.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Co-developed-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
With enabled SKIP_LOWLEVEL_INIT, the weak function timer_init() is
used in the SPL build. For iMX6 SoC, this leads MMC to fail once
u-boot proper is booted due to a timing issue.
Always use iMX-specific timer_init() in SPL to fix timing issues.
Fixes: be277c3a89 ("imx: mx7: avoid some initialization if low level is skipped")
Signed-off-by: Michael Scott <mike@foundries.io>
Co-developed-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
At the moment, we don't have a common API for working with
SM, only the smc_call() function. This approach is not generic
and difficult to configure and maintain.
This patch adds UCLASS_SM with the generic API:
- sm_call()
- sm_call_write()
- sm_call_read()
These functions operate with struct pt_regs, which describes
Secure Monitor arguments.
Signed-off-by: Alexey Romanov <avromanov@salutedevices.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20230921081346.22157-2-avromanov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
- Fix a memset call in the optee_agent code.
Then to quote the author for the rest of the changes:
This patch series allows users to access SCMI base protocol provided by
SCMI server (platform). See SCMI specification document v3.2 beta[1]
for more details about SCMI base protocol.
What is currently not implemented is
- SCMI_BASE_NOTIFY_ERRORS command and notification callback mechanism
This feature won't be very useful in the current U-Boot environment.
[1] https://developer.arm.com/documentation/den0056/e/?lang=en
The sess variable in open_channel was not entirely
cleared to zero at the start of this function.
This commit ensures that the entire struct is cleared.
Signed-off-by: Francois Berder <fberder@outlook.fr>
Now that we have Base protocol support, we will be able to check if a given
protocol is really supported by the SCMI server (firmware).
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Added is a new unit test for SCMI base protocol, which will exercise all
the commands provided by the protocol, except SCMI_BASE_NOTIFY_ERRORS.
$ ut dm scmi_base
It is assumed that test.dtb is used as sandbox's device tree.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
SCMI base protocol is mandatory, and once SCMI node is found in a device
tree, the protocol handle (udevice) is unconditionally installed to
the agent. Then basic information will be retrieved from SCMI server via
the protocol and saved into the agent instance's local storage.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
Adding SCMI base protocol makes it inconvenient to hold the agent instance
(udevice) locally since the agent device will be re-created per each test.
Just remove it and simplify the test flows.
The test scenario is not changed at all.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
In SCMI base protocol version 2 (0x20000), new interfaces,
BASE_SET_DEVICE_PERMISSIONS/BASE_SET_PROTOCOL_PERMISSIONS/
BASE_RESET_AGENT_CONFIGURATION, were added. Moreover, the api of
BASE_DISCOVER_AGENT was changed to support self-agent discovery.
So the driver expects SCMI firmware support version 2 of base protocol.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
SCMI base protocol is mandatory according to the SCMI specification.
With this patch, SCMI base protocol can be accessed via SCMI transport
layers. All the commands, except SCMI_BASE_NOTIFY_ERRORS, are supported.
This is because U-Boot doesn't support interrupts and the current transport
layers are not able to handle asynchronous messages properly.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
Any SCMI protocol may have its own channel.
Test this feature on sandbox as the necessary framework was added
in a prior commit.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
This framework allows SCMI protocols to be installed and bound to the agent
so that the agent can manage and utilize them later.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
Move the location of scmi_bind_protocols() backward for changes
in later patches.
There is no change in functionality.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
In sandbox scmi agent, channels are not used at all. But in this patch,
dummy channels are supported in order to test protocol-specific channels.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
SCMI specification allows any protocol to have its own channel for
the transport. While the current SCMI driver may assign its channel
from a device tree, the core function, devm_scmi_process_msg(), doesn't
use a protocol's channel, but always use an agent's channel.
With this commit, devm_scmi_process_msg() tries to find and use
a protocol's channel. If it doesn't exist, use an agent's.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The commit 85dc582892 ("firmware: scmi: prepare uclass to pass channel
reference") added an explicit parameter, channel, but it seems to make
the code complex.
Hiding this parameter will allow for adding a generic (protocol-agnostic)
helper function, i.e. for PROTOCOL_VERSION, in a later patch.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Etienne Carriere <etienne.carriere@foss.st.com>
Add support in binman for generating EFI empty capsules. These
capsules are used in the FWU A/B update feature. Also add test cases
in binman for the corresponding code coverage.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a method to the mkeficapsule bintool to generate empty
capsules. These are capsules needed for the FWU A/B update feature.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The various fields of a generated capsule are currently verified
through hard-coded offsets. Use the dump-capsule feature for dumping
the capsule header contents and use those for capsule verification.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The #address-cells and #size-cells are not needed for running the
capsule generation binman tests. Remove the superfluous properties.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add documentation to explain the printing of the capsule headers
through the mkeficapsule tool.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support to dump the contents of capsule headers. This is useful as
a debug feature for checking the contents of the capsule headers, and
can also be used in capsule verification.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
A follow-up to commit 842fb5de42
("drivers: use devfdt_get_addr_size_index_ptr when cast to pointer")
and commit 320a1938b6
("drivers: use devfdt_get_addr_index_ptr when cast to pointer").
In addition to using the *_ptr variants of these functions where the
address is cast to a pointer, this also changes devfdt_get_addr_*() to
dev_read_addr_*() in a few places. Some variable and field types are
changed from fdt_addr_t or phys_addr_t to void* where the cast was
happening later.
This patch fixes a number of compile warnings when building a 32bit
U-Boot with CONFIG_PHYS_64BIT=y. In some places, it also fixes error
handling where the return value of dev_read_addr() etc. was checked for
NULL instead of FDT_ADDR_T_NONE.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
pinctrl-single uses fdt_addr_t and phys_addr_t inconsistently, but both
are wrong to be passed to readb() etc., which expect a pointer or
pointer-sized integer. Change the driver to use
dev_read_addr_size_index_ptr(), so we consistently deal with void*
(except for the sandbox case and single_get_pin_muxing()).
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add missing mapmem.h header:
Signed-off-by: Simon Glass <sjg@chromium.org>
Same as dev_read_addr_name[_size](), but returns a pointer, cast
through map_sysmem().
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Checking for the error cast to fdt_addr_t is rather awkward - IS_ERR()
can be used, but it's not really made to be used on fdt_addr_t, which
may not even be the same size as a native pointer.
Most places in U-Boot only check for FDT_ADDR_T_NONE; let's adjust the
error return to match the expectation.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- The dev_read_addr_name*() family of functions has no "index" argument,
doc comments should refer to "name"
- Specify the error return for several devfdt_get_addr*() functions
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The argument type of `build_from_git` was changed from string to list
in d71e711699.
This commit adapts the argument type of all bintools using this
function.
Signed-off-by: Lukas Funke <lukas.funke@weidmueller.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
sandbox_spl_defconfig with CONFIG_SPL_UNIT_TEST=n fails to build.
in function `spl_board_init':
arch/sandbox/cpu/spl.c:134:(.text.spl_board_init+0x4a):
undefined reference to `ut_run_list'
Add the missing configuration check.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When the boot_targets environment variable is used with the distro-boot
scripts, each device is included individually. For example, if there
are three mmc devices, then we will have something like:
boot_targets="mmc0 mmc1 mmc2"
In contrast, standard boot supports specifying just the uclass, i.e.:
boot_targets="mmc"
The intention is that this should scan all MMC devices, but in fact it
currently only scans the first.
Update the logic to handle this case, without required BOOTSTD_FULL to
be enabled.
I believe at least three people reported this, but I found two.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Date Huang <tjjh89017@hotmail.com>
Reported-by: Vincent Stehlé <vincent.stehle@arm.com>
Pull request efi-2024-01-rc1
Documentation:
* Bump urllib3 version
* Migrate Renesas board docs to rst
* Link an introduction video
UEFI
* Use same GUID as EDK II for auto-created boot options
* Clean up BitBlt test
Xilinx changes for v2024.01-rc1 v3
clk:
- remove additional compatible strings for Versal NET
net:
- zynq_gem: Fix clock calculation for MDC for higher frequencies
pinctrl:
- core: Extend pinmux status buffere size
- zynqmp driver: Show also tristate configuration
test:
- add test case for pxe get
Xilinx:
- describe SelectMAP boot mode
Zynq:
- Fix nand description in DT
ZynqMP:
- DTS sync patches with kernel and also W=1 related fixes
- Add support for KD240, zcu670, e-a2197 with x-prc cards, SC revB/C with i2c
description for other SC based boards
- k24 psu_init cleanup
Pull request for u-boot-nand-20231013
The first 5 patches are from Mikhail Kshevetskiy, aligning the mtd spinand
core with kernel version 5.15.43, fixing a bug on Winbond, and adding
support for Winbond W25NO2KV.
The other 2 patches are from Patrick Delaunay and they fix a bug and mark
bad the MTD block on erase error.
In the existing implementation, multiple requests queued up on an
endpoint are subject to getting evicted without transmission.
For both control and bulk endpoints, their respective logic found in
usba_control_irq()/usba_ep_irq() guarantees that TX FIFO is empty before
data is sent out, and that request_complete() gets called once the
transaction has been finished. At this point however, if any additional
requests are found on the endpoint queue, they will be processed by
submit_next_request(), which makes no checks against the above
conditions, trashing data on a busy FIFO and neglecting completion
handlers.
Fix the above issues by removing the calls to submit_next_request(),
and thus forcing the pending requests to be processed on the next pass
of the respective endpoint logic. While at it, remove a DBG message, as
that branch becomes part of regular flow.
This restores mass storage mode operation on Microchip ATSAMA5D27 SoC.
Signed-off-by: Artur Rojek <artur@conclusive.pl>
In the MTD DFU backend, it is needed to mark the NAND block bad when the
erase failed with the -EIO error, as it is done in UBI and JFFS2 code.
This operation is not done in the MTD framework, but the bad block
tag (in BBM or in BBT) is required to avoid to write data on this block
in the next DFU_OP_WRITE loop in mtd_block_op(): the code skip the bad
blocks, tested by mtd_block_isbad().
Without this patch, when the NAND block become bad on DFU write operation
- low probability on new NAND - the DFU write operation will always failed
because the failing block is never marked bad.
This patch also adds a test to avoid to request an erase operation on a
block already marked bad; this test is not performed in MTD framework
in mtd_erase().
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The offset variable = 'off' used in the error trace when limit is reach
on erase operation is incorect as 'erase_op.addr' is used in the loop.
This patch corrects the copy paste issue between the erase loop and
the write loop.
This patch also adds the 'remaining' information to allow to debug of
limit issues.
Fixes: 6015af28ee ("dfu: add backend for MTD device")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Currently there are 3 different variants of read_id implementation:
1. opcode only. Found in GD5FxGQ4xF.
2. opcode + 1 addr byte. Found in GD5GxGQ4xA/E
3. opcode + 1 dummy byte. Found in other currently supported chips.
Original implementation was for variant 1 and let detect function
of chips with variant 2 and 3 to ignore the first byte. This isn't
robust:
1. For chips of variant 2, if SPI master doesn't keep MOSI low
during read, chip will get a random id offset, and the entire id
buffer will shift by that offset, causing detect failure.
2. For chips of variant 1, if it happens to get a devid that equals
to manufacture id of variant 2 or 3 chips, it'll get incorrectly
detected.
This patch reworks detect procedure to address problems above. New
logic do detection for all variants separatedly, in 1-2-3 order.
Since all current detect methods do exactly the same id matching
procedure, unify them into core.c and remove detect method from
manufacture_ops.
This is a rework of Chuanhong Guo <gch981213@gmail.com> patch
submitted to linux kernel
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/all/20230110115843.391630-1-frieder@fris.de
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Make that condition more generic by checking if the memory controller
driver is enabled instead of using the EVM's config.
Signed-off-by: Dominik Haller <d.haller@phytec.de>
Update the MAINTAINERS file and propose a new MAINTAINER for j721s2 due
to the previous MAINTAINER not being associated with TI.
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
The following commit syncs the device tree from Linux tag
v6.6-rc1 to U-boot and fixes the following to be compatible with
the future syncs -
- Include k3-am68-sk-base-board.dts file
Remove the duplicated pinmuxes from r5 and -u-boot.dtsi files and
include k3-am68-sk-base-board.dts for Linux fixes to propagate
to U-boot.
- Fixing the mcu_timer0
Remove timer0 and use the mcu_timer0 defined in mcu-wakeup.dtsi
- Fixing secure proxy nodes
Linux DT now have these nodes defined so remove them and rename to
use the Linux DT ones.
- Remove cpsw node
The compatible is now fixed and the node is not required in
-u-boot specifically
- Remove aliases and chosen node
Use these from Linux and don't override when not required.
- Remove /delete-property/ from sdhci nodes
We have the necessary clock and dev data so remove these.
- Remove dummy_clocks and fs_loader0
These weren't being used anywhere so remove it.
- Remove mcu_ringacc override
All these have been put in a single commit to not break the
bisectability.
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
The following commit syncs the device tree from Linux tag
v6.6-rc1 to U-boot and fixes the following to be compatible with
the future syncs -
- Include k3-j721s2-common-proc-board.dts file
Remove the duplicated pinmuxes from r5 and -u-boot.dtsi files and
include k3-j721s2-common-proc-board.dts for Linux fixes to propagate
to U-boot.
- Fixing the mcu_timer0
Remove timer0 and use the mcu_timer0 defined in mcu-wakeup.dtsi
- Fixing secure proxy nodes
Linux DT now have these nodes defined so remove them and rename to
use the Linux DT ones.
- Remove cpsw node
The compatible is now fixed and the node is not required in
-u-boot specifically
- Remove aliases and chosen node
Use these from Linux and don't override when not required.
- Remove /delete-property/ from sdhci nodes
We have the necessary clock and dev data so remove these.
- Remove dummy_clocks and fs_loader0
These weren't being used anywhere so remove it.
- Remove mcu_ringacc override
All these have been put in a single commit to not break the
bisectability.
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
mcu_timer0 is used by u-boot as the tick-timer. Add it to the soc
devices lsit so it an be enabled via the k3 power controller.
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
The update causes instability in am68-sk boards so revert the patch in
the meantime till fix is available.
This reverts commit f1edf4bb6a.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
The malloc capacity in DRAM at R5 SPL is set to 1MB which isn't
sufficient to load the new tispl.bin to
enable loading of tispl.bin the size is increased by 256KB to 1.25MB.
Cc: Nikhil M Jain <n-jain1@ti.com>
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Reviewed-by: Nikhil M Jain <n-jain1@ti.com>
Sync j7200 dts with Linux 6.6-rc1
- k3-j7200-r5-common-proc-board.dts now inherits from
k3-j7200-common-proc-board.dts instead of k3-j7200-som-p0.dtsi. This
allows us to trim down the r5 file considerably by using existing
properties
- remove pimux nodes from r5 file
- remove duplicate nodes & node properties from r5/u-boot files
- mcu_timer0 now used instead of timer1
mcu_timer0 device id added to dev-data.c file in order to work
- remove cpsw node
This node is no longer required since the compatible is now fixed
- remove dummy_clock_19_2_mhz
This node wasn't being used anyhere, so it was removed
- remove dummy_clock_200mhz
main_sdhci0 & main_sdhci1 no longer need dummy clock for eMMC/SD
- fix secure proxy node
mcu_secproxy changed to used secure_prxy_mcu which is already
defined in k3-j7200-mcu-wakeup.dtsi
- removed &mcu_ringacc property override since they're present in
v6.6-rc1
Signed-off-by: Reid Tonking <reidt@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
mcu_timer0 is now used as the tick timer in u-boot, so this adds the
timer to the soc device list so it can be enabled via the k3 power
controller.
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Reid Tonking <reidt@ti.com>
Switch to using bootstd. Note with this change, we will stop using
distro_bootcmd and instead depend entirely on bootflow method of
starting the system up.
Drop header files that are no longer needed in am64x_evm.h.
k3_dfu.h is available via k3_dfu.env in am64x.env.
Drop unused macro CFG_SYS_SDRAM_BASE1.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
ti_mmc is not a valid boot_target for standard boot flow so
remove it. Prefer mmc1 (sd-card) over mmc0 (emmc).
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
AVS driver needs to be notified before or after clock change,
depending upon new rate is greater or less than current clock rate.
Fixes: 1e0aa873bc7cd ("clk: clk-ti-sci: Notify AVS driver upon setting clock rate")
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
AVS is enabled at R5 SPL stage, on few platforms like J721E
and J7200 clk-k3 is used instead if clk-sci driver.
Add support in clk-k3 driver as well to notify AVS driver
on setting clock rate so that voltage is changed accordingly.
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
To quote the author:
So far expo only supports menus. These are quite flexible for various
kinds of settings, but cannot deal with free-form input, such as a
serial number or a machine name.
This series adds support for a textline object, which is a single line
of text. It has a maximum length and its value is stored within the expo
structure.
U-Boot already has a command-line editor which provides most of the
features needed by expo. But the code runs in its own loop and only
returns when the line is finished. This is not suitable for expo, which
must handle a keypress at a time, returning to its caller after each
one.
In order to use the CLI code, some significant refactoring is included
here. This mostly involves moving the internal loop of the CLI to a
separate function and recording its state in a struct, just as was done
for single keypresses some time back. A minor addition is support for
Ctrl-W to delete a word, since strangely this is currently only present
in the simple version.
The video-console system provides most of the features needed by
testline, but a few things are missing. This series provides:
- primitive cursor support so the user can see where he is typing
- saving and restoring of the text-entry context, so that expo can allow
the user to continue where he left off, including deleting previously
entered characters correctly (for Truetype)
- obtaining the nominal width of a string of n characters, so that a
suitable width can be chosen for the textline object
Note that no support is provided for clearing the cursor. This was
addressed in a previous series[1] which could perhaps be rebased. For
this implementation, the cursor is therefore not enabled for the normal
command line, only for expo.
Reading and writing textline objects is supported for FDT and
environment, but not for CMOS RAM, since it would likely use too much
RAM to store a string.
In terms of code size, the overall size increase is 180 bytes for
Thumb02 boards, 160 of whcih is the addition of Ctrl-W to delete a word.
[1] https://patchwork.ozlabs.org/project/uboot/list/?series=280178&state=*
The boot option automatically created by efibootmgr is identified
by the special guid appended in the optional data of boot option.
The same mechanism is implemented in the EDK II reference
implementation, it uses the different guid from the one currently
U-Boot uses.
The guid indicating auto-created boot option is not defined in the
UEFI specification, but some userspace tools such as 'efivar' package
are aware of the guid used in EDK II as auto-created boot option.
So let's use the same guid as EDK II reference implementation.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The BitBlt test leaves the serial console output in disarray.
* Call ClearScreen() where needed.
* Test CheckEvent() for EFI_SIMPLE_TEXT_INPUT_PROTOCOL.WaitForKey
via adding navigation keys
* Correct timer comment
For testing on the sandbox:
CONFIG_CMD_BOOTEFI_SELFTEST=y
CONFIG_CONSOLE_TRUETYPE=n
$ ./u-boot -T -l
=> setenv efi_selftest block image transfer
=> bootefi selftest
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Some of the information in README.rmobile is obsolete, references
defconfigs which no longer exist in u-boot or has broken links. The
information which is still relevant is moved into the reStructuredText
documentation under `doc/board/renesas`, and `doc/README.rmobile` is
dropped.
The list of boards in `doc/board/renesas` is converted into a table so
it's easier to see which defconfig to use. The list is expanded based on
reviewing the current u-boot code and the contents of the eLinux wiki
[1] [2].
[1]: https://elinux.org/R-Car
[2]: https://elinux.org/RZ-G
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Cyclic now just print a warning once instead of disabling the cyclic
function when the cyclic function upon exceeding CPU time usage.
Fixes: ddc8d36a74 ("cyclic: Don't disable cylic function upon exceeding CPU time")
Signed-off-by: Weizhao Ouyang <o451686892@gmail.com>
Rephrase the paragraph.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
While not a direct issue for us, urllib3 before 1.26.17 is vulnerable to
CVE-2023-43804 to bump our version up.
Reported-by: GitHub dependabot
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use urllib3 2.0.6
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Add textline to the list of objects which tthe expo builder can build.
This allows them to be provided in the description.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present cedit only supports menu keys. For textline objects we need
to insert normal ASCII characters.
We also need to handle backspace, which is ASCII 9.
In fact, expo does not make use of all the menu keys, so partition
them accordingly and update the logic to support normal ASCII
characters, too.
Signed-off-by: Simon Glass <sjg@chromium.org>
Provide an implementation for textlines in the scene code, so that they
are displayed correctly. Provide a way to have a border around the
textline, with the internal part being the same colour as the
background. This looks more natural.
Signed-off-by: Simon Glass <sjg@chromium.org>
This object needs special handling when it is opened, to set up the CLI
and the vidconsole context. Add special support for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
A textline is a line of text which can be edited by the user. It has a
maximum length (in chracters) but otherwise there are no restrictions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add the CLI state, a buffer to hold the old value of the text being
edited and a place to save vidconsole entry context. These will be use
by the textline object.
Set an upper limit on the maximum number of characters in a textline
object supported by expo, at least for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
So far only menus have a background. When other object types are
rendered, they may have a background too. Make this code more generic
so it will be usable by new object types.
Signed-off-by: Simon Glass <sjg@chromium.org>
When the devicetree is too small for the property being written, we need
to expand the devicetree and retry the write.
Put this logic into a function so it can be reused.
Signed-off-by: Simon Glass <sjg@chromium.org>
So far only menus can be highlighted. With the coming addition of
text lines we need to be able to highlight other objects. Add a function
to determine whether an object can be highlighted.
Signed-off-by: Simon Glass <sjg@chromium.org>
In a lot of cases menus are the only objects which are have their own
behaviour in the cedit, e.g. to move between menus. With expo expanding
to support text, this is no-longer true.
Use a switch() statement so that we can simply insert a new 'case' for
the new object types.
Signed-off-by: Simon Glass <sjg@chromium.org>
When building an expo fails, show some information about which node
caused the problem. Use -ENOENT consistently when the ID is missing.
This makes it easier for the user to debug things.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add rudimentary support for displaying a cursor on a vidconsole. This
helps the user to see where text is being entered.
The implementation so far is very simple: the cursor is just a vertical
bar of fixed width and cannot be erased. To erase the cursor, the text
must be redrawn over it.
This is good enough for expo but will need enhancement to be useful for
the command-line console. For example, it could save and restore the
area behind the cursor.
For now, enable this only for expo, to reduce code size.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this is called only when a newline is detected, since this
indicates the start of a line of text being entered.
Export this function so it can be used by expo, which may start a new
text line itself, without first writing out a newline.
Signed-off-by: Simon Glass <sjg@chromium.org>
Text entry operates within a context which includes quite a bit of
information. For example, with Truetype fonts, each character in the
text string has a position stored, so that it is possible to
backspace to that character. This information is built up as strings
are drawn on the display.
For the command line, there is just a single context. It is created
when command-line entry starts and it is destroyed (or at least not
needed anymore) when the user presses <enter> to enter the command.
By contrast, expo needs to be able to switch in and out of a text-entry
context, since it is also displaying other objects in the scene.
Add a way to save and restore the entry context for a vidconsole. This
is only needed for the truetype vidconsole, so add a method for that,
storing the information in an abuf struct.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present there is a method for measuring text, but if the actual text
string is not known, it cannot be used.
For text editor we want to set the size of the entry box to cover the
expected text size. Add the concept of a 'norminal' size with a method
to calculate that for the vidconsole.
If the method is not implemented, fall back to using the font size,
which is sufficient for fixed-width fonts.
Signed-off-by: Simon Glass <sjg@chromium.org>
When inputting text outside the command line we don't want to use tab
for command completion. Add an option to control this.
Signed-off-by: Simon Glass <sjg@chromium.org>
When inputting text outside the command line we don't want history to be
accessible. Add an option to control this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than relying on the caller, terminate the string inside this
function. Do this each time we return, whether input is finished or
not. It is not needed when the input is aborted, since the string will
be discarded in that case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move most of the inner loop from cread_line() into a new function. This
will allow using it from other code.
This involves adding a few more members to the state struct.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reduce the indentation level of this code so it is easier to review the
next patch, which moves it into a function.
Signed-off-by: Simon Glass <sjg@chromium.org>
We want to reuse the editing code elsewhere. As a first step, move the
common variables into a struct. This will allow us to eventually put the
contents of the inner loop in a function, so it can be called from
elsewhere.
Signed-off-by: Simon Glass <sjg@chromium.org>
The index values are not very large so it makes no sense to use a long
integer. Change these to uint instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
The Ctrl-W option is implemented in the cread_line_simple() but not in
the full version. This seems odd, so add an implementation.
Signed-off-by: Simon Glass <sjg@chromium.org>
There is a function for this but it is never used. Showing the history is
a useful feature, so add a new 'history' command.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is part of a longer series, which isn't quite ready. Revert this
for now at least.
This reverts commit 4cb6c8e5f0.
Signed-off-by: Tom Rini <trini@konsulko.com>
To quote the author:
I'm submitting a patch series that ports the gen_compile_commands.py
script from the Linux kernel's sources to U-Boot. This script,
originally located in scripts/clang-tools/gen_compile_commands.py,
enables the generation of compile_commands.json file for improved code
navigation and analysis. The series consists of the initial script
import, the necessary modifications for U-Boot compatibility, and
finally some documentation.
Add 'Integration with IDEs' chapter.
For now, this chapter is mostly a reference to the documentation of
gen_compile_commands, in doc/build, but it can be futurely used as
a guide for other IDE-friendly features.
Signed-off-by: Joao Marcos Costa <jmcosta944@gmail.com>
Tested-by: Joao Paulo Goncalves <joao.goncalves@toradex.com>
This documentation briefly explains what is a compilation database,
and how to use the script to generate one.
This is not a portage, as there was no original documentation in the
Linux sources.
Acknowledge the documentation in the script's header and in doc/build
index.
Signed-off-by: Joao Marcos Costa <jmcosta944@gmail.com>
Tested-by: Joao Paulo Goncalves <joao.goncalves@toradex.com>
Add Clang's compilation database file (i.e. compile_commands.json) to
.gitignore, at the root of the repository.
Signed-off-by: Joao Marcos Costa <jmcosta944@gmail.com>
Tested-by: Joao Paulo Goncalves <joao.goncalves@toradex.com>
Add acknowledgments for porting and modifying the script. Of course, the
license, author, and copyright notice remain the same as in the original
script.
Signed-off-by: Joao Marcos Costa <jmcosta944@gmail.com>
Tested-by: Joao Paulo Goncalves <joao.goncalves@toradex.com>
The referred tool is now in U-Boot. Replace "the Linux kernel" by
"U-Boot" to make the docstring coherent.
Signed-off-by: Joao Marcos Costa <jmcosta944@gmail.com>
Tested-by: Joao Paulo Goncalves <joao.goncalves@toradex.com>
For U-Boot's context, the regular expression defined by _LINE_PATTERN
should be adapted. Replace 'savedcmd' by 'cmd'.
Signed-off-by: Joao Marcos Costa <jmcosta944@gmail.com>
Tested-by: Joao Paulo Goncalves <joao.goncalves@toradex.com>
This script generates a database of compiler flags, namely
compile_commands.json. It is quite useful for text editors that use
clangd LSP (e.g. Vim, Neovim).
It was ported from Linux's sources:
- tag: v6.4
- revision 6995e2de6891c724bfeb2db33d7b87775f913ad1
Modifications for U-Boot compatibility will be added in a follow-up
commit.
Signed-off-by: Joao Marcos Costa <jmcosta944@gmail.com>
Tested-by: Joao Paulo Goncalves <joao.goncalves@toradex.com>
- Assorted TI K3 updates, use ".dtso" for device tree overlays to match
general usage, mkimage fixes/improvements, assorted platform
updates/fixes, other assorted driver/platform fixes.
All K3 boards now are secure by default, instead of setting this in each
defconfig, make it implied by the ARCH config.
The only exception is IOT2050, which I do not believe will have any
problems with being a TI_SECURE_DEVICE, but for now turn it off to keep
its config the same.
Signed-off-by: Andrew Davis <afd@ti.com>
Tested-by: Tom Rini <trini@konsulko.com>
K3 devices have runtime type board detection. Make the default defconfig
include the secure configuration. Then remove the HS specific config.
Non-HS devices will continue to boot due to runtime device type detection.
Signed-off-by: Andrew Davis <afd@ti.com>
Tested-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Manorit Chawdhry <m-chawdhry@ti.com>
As the code to switch an ARM core from secure to the non-secure state
needs to know the base address of the Generic Interrupt Controller
(GIC), we read an Arm Cortex defined system register that is supposed to
hold that base address. However there are SoCs out there that get this
wrong, and this CBAR register either reads as 0 or points to the wrong
address. To accommodate those systems, so far we use a macro defined in
some platform specific header files, for affected boards.
To simplify future extensions, replace that macro with a Kconfig variable
that holds this override address, and define a default value for SoCs
that need it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Sam Edwards <CFSworks@gmail.com>
DM_DRIVER_GET will redeclare the fs_loader driver without the correct
alignment. This causes GCC to use the default section alignment of 32
bytes. This in turn creates a gap in the linker list due to the padding
required to achieve the correct alignment, corrupting all further entries.
Use DM_DRIVER_REF instead, which doesn't redeclare anything.
Fixes: 0998a20cfc ("misc: fs_loader: Add function to get the chosen loader")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
The man page correctly said that -B was ignored without -E, while the
`mkimage -h` output suggested otherwise. Now that -B can actually be
used by itself, update the man page.
While at it, also amend the `mkimage -h` line to mention the
connection with -E.
The FDT header is a fixed 40 bytes, so its size cannot (and is not)
modified, while its alignment is a property of the address in RAM one
loads the FIT to, so not something mkimage can affect in any way. (In
the file itself, the header is of course at offset 0, which has all
possible alignments already.)
Reported-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Simon Glass <sjg@chromium.org>
Moving towards using .dtso for overlay sources, update the
documentation examples to follow that pattern.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Simon Glass <sjg@chromium.org>
Distinguish more clearly between source files meant for producing .dtb
from those meant for producing .dtbo. No functional change, as we
currently have rules for producing a foo.dtbo from either foo.dts or
foo.dtso.
Note that in the linux tree, all device tree overlay sources have been
renamed to .dtso, and the .dts->.dtbo rule is gone since v6.5 (commit
81d362732bac). So this is also a step towards staying closer to linux
with respect to both Kbuild and device tree sources.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Simon Glass <sjg@chromium.org>
Distinguish more clearly between source files meant for producing .dtb
from those meant for producing .dtbo. No functional change, as we
currently have rules for producing a foo.dtbo from either foo.dts or
foo.dtso.
Note that in the linux tree, all device tree overlay sources have been
renamed to .dtso, and the .dts->.dtbo rule is gone since v6.5 (commit
81d362732bac). So this is also a step towards staying closer to linux
with respect to both Kbuild and device tree sources.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Distinguish more clearly between source files meant for producing .dtb
from those meant for producing .dtbo. No functional change, as we
currently have rules for producing a foo.dtbo from either foo.dts or
foo.dtso.
Note that in the linux tree, all device tree overlay sources have been
renamed to .dtso, and the .dts->.dtbo rule is gone since v6.5 (commit
81d362732bac). So this is also a step towards staying closer to linux
with respect to both Kbuild and device tree sources.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Distinguish more clearly between source files meant for producing .dtb
from those meant for producing .dtbo. No functional change, as we
currently have rules for producing a foo.dtbo from either foo.dts or
foo.dtso.
Note that in the linux tree, all device tree overlay sources have been
renamed to .dtso, and the .dts->.dtbo rule is gone since v6.5 (commit
81d362732bac). So this is also a step towards staying closer to linux
with respect to both Kbuild and device tree sources.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Apple's M2 Ultra SoC are somewhat similar to the M1 Ultra but needs
a tweaked memory map as the M2 Pro/Max SoCs. USB, NVMe, UART, WDT
and PCIe are working with the existing drivers.
Signed-off-by: Janne Grunau <j@jannau.net>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
When reading Kconfig help messages to understand ENV_OFFSET and
ENV_OFFSET_REDUND, developers may not realise that they need to also
look at the chosen ENV_IS_IN_* options to see how the offsets will be
interpreted.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The ARMv8.5 architecture extension defines architectural RNDR/RNDRRS
system registers, that provide 64 bits worth of randomness on every
read. Since it's an extension, and implementing it is optional, there is
a field in the ID_AA64ISAR0_EL1 ID register to query the availability
of those registers.
Add a UCLASS_RNG driver that returns entropy via repeated reads from
those system registers, if the extension is implemented.
The driver always binds, but checks the availability in the probe()
routine.
This helps systems which suffer from low boot entropy, since U-Boot can
provide entropy via the generic UEFI entropy gathering protocol to the OS,
at an early stage.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Padding the header of an external FIT image is achieved by truncating
the existing temporary FIT file to match the required alignment before
appending image data. Reusing an existing file this way means that the
padding will likely contain a portion of the original data not
overwritten by the new header.
Zero out any data past the end of the new header, and stop at either
the end of the desired padding, or the end of the old FIT file,
whichever comes first.
Fixes: 7946a814a3 ("Revert "mkimage: fit: Do not tail-pad fitImage with external data"")
Signed-off-by: Roman Azarenko <roman.azarenko@iopsys.eu>
Reviewed-by: Simon Glass <sjg@chromium.org>
A53 U-Boot proper got broken because nodes marked as 'bootph-pre-ram'
are no longer available in U-Boot proper before relocation.
Fix this by marking all nodes in u-boot.dtsi as 'bootph-all'.
Fixes: 9e644284ab ("dm: core: Report bootph-pre-ram/sram node as pre-reloc after relocation")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
dlmalloc has some sanity checks it performs on free() which can help detect
memory corruption. However, they are only enabled if DEBUG is defined before
including common.h. Define DEBUG earlier if UNIT_TEST is enabled so that
assertions are enabled in sandbox.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since commit 9e644284ab ("dm: core: Report bootph-pre-ram/sram node
as pre-reloc after relocation") A53 u-boot proper is broken. This is
because nodes marked as 'bootph-pre-ram' are not available at u-boot
proper before relocation.
To fix this we mark all nodes in u-boot.dtsi as 'bootph-all'.
Fixes: 69b19ca67b ("arm: dts: k3-j721e: Sync with v6.6-rc1")
Cc: Neha Francis <n-francis@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Tom Rini <trini@konsulko.com> # J721E-EVM GP
Tested-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
This is now done using binman but this file was leftover and is now
unused, remove it.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
This caused the wrong fdtfile to be set and was failing to apply M.2
settings.
Fixes: badaa1f6a7 ("boards: siemens: iot2050: Unify PG1 and PG2/M.2 configurations again")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Since commit 9e644284ab ("dm: core: Report bootph-pre-ram/sram node
as pre-reloc after relocation") A53 u-boot proper is broken. This is
because nodes marked as 'bootph-pre-ram' are not available at u-boot
proper before relocation.
To fix this we mark all nodes in u-boot.dtsi as 'bootph-all'.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
With commit 793e623011 ("spi: mtk_spim: get spi clk rate only once") a
new system to calculate the SPI clocks has been added.
Unfortunately, the do_div macro overrides the global priv->pll_clk_rate
field. This will cause to have a reduced clock rate on each subsequent
SPI call.
Signed-off-by: Valerio 'ftp21' Mancini <ftp21@ftp21.eu>
Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
We're seeing sporadic errors like
ENVC include/generated/env.txt
HOSTCC scripts/basic/fixdep
ENVP include/generated/env.in
ENVT include/generated/environment.h
HOSTCC tools/printinitialenv
/bin/sh: 1: scripts/basic/fixdep: not found
make[1]: *** [scripts/Makefile.host:95: tools/printinitialenv] Error 127
make[1]: *** Deleting file 'tools/printinitialenv'
make: *** [Makefile:2446: u-boot-initial-env] Error 2
make: *** Waiting for unfinished jobs....
where sometimes the "fixdep: not found" is instead "fixdep: Permission
denied" and the Error 127 becomes 126.
This smells like a race condition, and indeed it is: Currently,
u-boot-initial-env is a prerequisite of the envtools target, which
also lists scripts_basic as a prerequisite:
envtools: u-boot-initial-env scripts_basic $(version_h) $(timestamp_h) tools/version.h
$(Q)$(MAKE) $(build)=tools/env
However, the u-boot-initial-env rule involves building the
printinitialenv helper, which in turn is built using an if_changed_dep
rule. That means we must ensure scripts/basic/fixdep is built and
ready before trying to build printinitialenv, i.e. the
u-boot-initial-env rule itself must depend on the phony scripts_basic
target.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Simon Glass <sjg@chromium.org>
Added new xenguest_arm64_virtio_defconfig which
enables support for virtio-blk using various types
of transport like virtio-pci, vrtio-mmio. Currently
supported: up to 2 PCI host bridges and 10 MMIO devices.
Note: DT parsing code was partly taken from pci-uclass.c
Limitation: All memory regions should be
below 4GB address space.
Signed-off-by: Andrii Chepurnyi <andrii_chepurnyi@epam.com>
Current gd->ram_size and gd->ram_top reflect only the
first DRAM bank even if the SynQuacer Developerbox could
have up to three DRAM banks.
With the commit 06d514d77c ("lmb: consider EFI memory map"),
the first DRAM bank indicates <4GB address, so whole >4GB memory
is marked as EFI_BOOT_SERVICES_DATA and it results that
U-Boot can not access >4GB memory.
Since 64-bits DRAM address is fully available on the SynQuacer
Developerbox, let's set the installed DIMM information to
gd->ram_top and gd->ram_size.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Before using the result of env_get("stdin") we must check if it is NULL.
Avoid #if. This resolves the -Wunused-but-set-variable issue and we don't
need a dummy assignment in the else branch. Anyway this warning is
disabled in the Makefile.
For sake of readability use an early return after the configuration check.
Checking CONFIG_SPL_BUILD is incorrect as env_get() is only defined if
CONFIG_$(SPL_TPL)ENV_SUPPORT=y.
Fixes: 985ca3945f ("spl: input: Allow input in SPL and TPL")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Make it possible for data that was externalized using a static external
position (-p) to be internalized. Enables the ability to convert
existing FIT images built with -p to be converted to a FIT image where the
data is internal, to be converted to a FIT image where the data is
external relative to the end of the FIT (-E) or change the initial
static external position to a different static external position (-p).
Removing the original external-data-related properties ensures that
they're not present after conversion. Without this, they would still be
present in the resulting FIT even if the FIT has been, for example,
internalized.
Signed-off-by: Lars Feyaerts <lars@bitbiz.be>
Reviewed-by: Simon Glass <sjg@chromium.org>
Have checkpatch.pl skip warnings for use of fdtdec_* functions in
ooling; livetree isn't used there.
Signed-off-by: Lars Feyaerts <lars@bitbiz.be>
Reviewed-by: Simon Glass <sjg@chromium.org>
To quote the author:
At present on Sandbox when binding to a host backing file, the host
block device is created with a hard-coded 512 bytes block size.
Such assumption works for most cases, but for situation that with a raw
image file dump from a pre-formatted GPT partitioned disk image from a
4KiB block size device, when binding this file to a host device and mapping
this device to a blkmap, "blkmap" command like "blkmap part" won't work
correctly, due to block size mismatch during parsing the partition table.
This series updates Sandbox block driver, as well as the blkmap driver,
to get rid of the hard-coded 512 bytes block size assumption.
This series is available at u-boot-x86/blk for testing.
Test log (512 block size):
=> host bind 0 test.img
=> host info
dev blocks blksz label path
0 262144 512 0 test.img
=> blkmap create 0
Created "0"
=> blkmap map 0 0 40000 linear host 0 0
Block 0x0+0x40000 mapped to block 0x0 of "host 0"
=> blkmap info
Device 0: Vendor: U-Boot Rev: 1.0 Prod: blkmap
Type: Hard Disk
Capacity: 128.0 MB = 0.1 GB (262144 x 512)
=> blkmap part
Partition Map for BLKMAP device 0 -- Partition Type: EFI
Part Start LBA End LBA Name
Attributes
Type GUID
Partition GUID
1 0x00000022 0x000000bd "u-boot-spl"
attrs: 0x0000000000000000
type: 5b193300-fc78-40cd-8002-e86c45580b47
(5b193300-fc78-40cd-8002-e86c45580b47)
guid: 0bb6bb6e-4aac-4c27-be03-016b01e7b941
2 0x00000822 0x00000c84 "u-boot"
attrs: 0x0000000000000000
type: 2e54b353-1271-4842-806f-e436d6af6985
(2e54b353-1271-4842-806f-e436d6af6985)
guid: 91d50814-8e31-4cc0-97dc-779e1dc59056
3 0x00000c85 0x0000cc84 "rootfs"
attrs: 0x0000000000000004
type: 0fc63daf-8483-4772-8e79-3d69d8477de4
(linux)
guid: 42799722-6e55-46e6-afa9-529e7af3f03b
Test log (4096 block size):
=> host bind 0 test.img 4096
=> host info
dev blocks blksz label path
0 32768 4096 0 test.img
=> blkmap create 0
Created "0"
=> blkmap map 0 0 8000 linear host 0 0
Block 0x0+0x8000 mapped to block 0x0 of "host 0"
=> blkmap info
Device 0: Vendor: U-Boot Rev: 1.0 Prod: blkmap
Type: Hard Disk
Capacity: 128.0 MB = 0.1 GB (32768 x 4096)
=> blkmap part
Partition Map for BLKMAP device 0 -- Partition Type: EFI
Part Start LBA End LBA Name
Attributes
Type GUID
Partition GUID
1 0x00000100 0x00001fff "primary"
attrs: 0x0000000000000000
type: 0fc63daf-8483-4772-8e79-3d69d8477de4
(linux)
guid: eba904d7-72c1-4dbd-bb4e-36be49cba5e3
2 0x00002000 0x00007ffa "primary"
attrs: 0x0000000000000000
type: 0fc63daf-8483-4772-8e79-3d69d8477de4
(linux)
guid: c48c360e-db47-46da-ab87-26416fad3cd3
Print out the blkmap device type when showing partition header for
a blkmap device.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
It's helpful to output the device uclass id for unknown devices
during the debugging process.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
blk_{read,write}_devnum() are no longer used by anywhere in the
source tree. Drop them.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
commit 3d2fc79714 ("cmd: blk: Allow generic read/write operations to work in sandbox")
used the hard-coded block size (512) for accessing the sandbox host
device. Now that we have added support for non-512 block size for both
Sandbox host device and blkmap driver, let's stop using the hard-coded
block size.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
get_desc() can be useful outside blk-uclass.c. Let's change it to
an API and make it externally visible.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present if a device to map has a block size other than 512,
the blkmap map process just fails. There is no reason why we
can't just use the block size of the mapped device.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
It's useful if we can print out the block size of the host device
in the "host info" command.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since we are emulating a block device, its size should be multiple
of the configured block size.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Allow optionally set the logical block size of the host device to
bind in the "host bind" command. If not given, defaults to 512.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
At present the host bind command does not require filename to be
provided. When it is not given NULL is passed to the host device
driver, which ends up failure afterwards.
Change to mandate the filename so that it is useful.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Cleanup how we pick what to launch in SPL, a few test changes, some TI
K3 platform updates, top-level Makefile fixes and related cleanup,
correct a problem with LMB overlap, other assorted fixes.
Reset the FLSHxCR1 registers to default value. ROM may set the register
value and it affects the SPI NAND normal functions.
Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Populate the device tree with the MC reserved memory regions.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Populate the device tree with the MC reserved memory regions.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add support for declaring in device tree the reserved memory ranges
required for MC. Since the MC firmware acts as any DMA master present
in the SoC, the reserved memory ranges need also be identity mapped
in the SMMU, so create the required 'iommu-addresses' property in
the reserved memory nodes.
For now this support is used only on LX2160A SoCs.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Some functions are not used outside this file, so make them static.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
PPA was a secure firmware developed in-house which is no longer
supported and replaced by TF-A quite some years ago. Drop support
for it.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
PPA was a secure firmware developed in-house which is no longer
supported and replaced by TF-A quite some years ago. This makes
the defconfigs that make use of PPA obsolete, so remove them.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
[Merged part 1 and part 2]
Signed-off-by: Peng Fan <peng.fan@nxp.com>
SPL doesn't have OF_LIVE enabled, so we can only run tests with a flat
tree. Don't skip them even if they don't use the devicetree.
Fixes: 6ec5178c0e ("test: Skip flat-tree tests if devicetree is not used")
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
String "/soc/fman/ethernet@e8000" is 25 bytes long
and not 24 due to extra byte for null character at
the end.
Signed-off-by: Francois Berder <fberder@outlook.fr>
When copying the name of a stdio device we must ensure that it is NUL
terminated before passing it to strcmp() to avoid a buffer overrun.
Truncating the name field leads to failure to deregister a stdio device.
When copying we must ensure that the name field sizes match.
Addresses-Coverity-ID: 350462 String not null terminated
Fixes: 5294e97832 ("stdio: extend "name" to 32 symbols")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The size of the name of a udevice is not limited.
When setting the fixed sized name field of a stdio device we must ensure
that the target string is NUL terminated to avoid buffer overflows.
Fixes: 57d92753d4 ("dm: Add a uclass for serial devices")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
spl_board_prepare_for_boot() is not called before jumping/invoking atf,
optee, opensbi or linux images.
Jump to image at the end of board_init_r() to fix this.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
spl_invoke_atf function will not be returned to SPL. Thus, we need to
set __noreturn function attribute to the function.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Use uintptr_t instead of phys_addr_t where appropriate, so passing the
addresses to writel() doesn't result in compile warnings when PHYS_64BIT
is set for 32bit builds (which is actually a useful configuration, as
the K3 SoC family boots from an R5 SPL, which may pass bank information
based on gd->bd->bi_dram to fdt_fixup_memory_banks() etc., so PHYS_64BIT
is needed for fixing up the upper bank).
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Execute "time <sleep cmd>", and validate that it gives the approximately
the correct amount of command execution time.
Signed-off-by: Love Kumar <love.kumar@amd.com>
Add test case for an address range which is coalescing with one of
range and overlapping with next range
Cc: Simon Glass <sjg@google.com>
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In case of new memory range to be added is coalesced
with any already added non last lmb region.
And there is possibility that, then region in which new memory
range added is not adjacent to next region. But have some
sections are overlapping.
So along with adjacency check with next lmb region,
check for overlap should be done.
In case overlap is found, adjust and merge these two lmb
region into one.
Reported-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
- None of the callers perform error checking and based on the non-empty
versions of this function, there's no checking to be done, so make
this a void.
- Add a default weak version of the function.
- Remove the empty versions of exynos_init now that we have a weak
version.
Signed-off-by: Tom Rini <trini@konsulko.com>
As part of reviewing a new platform, Daniel Schwierzeck noted that we
can have an empty Makefile in the board directory and don't need an
empty board.c file as well. Further with further cleanup in the
Makefile we can now omit the Makefile entirely. Remove a number of now
unnecessary board.c and Makefiles.
Signed-off-by: Tom Rini <trini@konsulko.com>
It is entirely possible at this point to have platforms in U-Boot that
do not have board-specific C code (just Kconfig or environment) and so
make it optional to have to descend in to and then build in the board
directory.
Signed-off-by: Tom Rini <trini@konsulko.com>
Allow for a proper configuration of CFI flash banks avaialble on the vexpress_ca9x4
board. Without this option, the CFI flash incorrectly detects that the board has two
banks of 32MB flash devices, while in reality, the board provides
two flash banks, each with 64MB size. As a result, it becomes impossible to e.g. to
save u-boot env in flash. According to device tree for this board and
its implementation in QEMU, the CFI width should be set to 32 bits.
After applying this fix, CFI flash will correctly detect both flash
banks each with a size of 64MB. As as result the functionality of e.g. saving u-boot
env will work correctly.
Tested on QEMU 6.2.0.
Cc: Kristian Amlie <kristian.amlie@northern.tech>
Signed-off-by: Patryk Biel <pbiel7@gmail.com>
Reviewed-by: Kristian Amlie <kristian.amlie@northern.tech>
If the source .env file changes to one that is also older than the
generated env.txt file then the .env file is not regenerated. This
means when switching board configs we do not regenerate the env.
This can be tested with:
$ make j721e_evm_a72_defconfig
$ make # this may fail to complete but that is okay for this test
$ make am64x_evm_a53_defconfig
$ make
$ vim include/generated/env.txt
Note this is still the J721e env not the AM64 config as expected.
As ENV_FILE is set based on configuration, regenerate anytime
autoconf.h changes.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The SelectMAP configuration interface provides an 8-bit,
16-bit or 32-bit bidirectional data bus interface to the Versal FPGA
configuration logic that can be used for both configuration and readback.
A connected microcontoller to the SelectMAP interface can load boot
image with bitstream, TF-A (ARM Trusted Firmware) and U-Boot.
This commit adds the missing identification of the SelectMAP mode.
Signed-off-by: Polak, Leszek <LPolak@arri.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Michal Simek <michal.simek@amd.com>
Cc: Stefan Roese <sr@denx.de>
Link: https://lore.kernel.org/r/DU0PR07MB8419F7765892CDBCE7D559C5C8CFA@DU0PR07MB8419.eurprd07.prod.outlook.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The board is sharing a lot of components with zcu208 but it contains
differet silicon and also several components are done differently.
The board has 4GB memory connected to PS and additional 4GB connected to
PL. Compare to zcu208 sata support has been dropped and only USB3.0 is
using GTR (lane2). Others GTRs are routed to connectors.
MIO configuration is also shared with zcu111.
The board is using si5381 chip compare to si5341 which is normally used.
And as of now there is no Linux driver for this chip. PS reference clock is
generated out of si570 chip which is also new approach compare to zcu208.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/3b296ef0f52bd94e32bdeb6d1beee29ac85f00a2.1695808407.git.michal.simek@amd.com
VPXA2785(vp-x-a2785-00) is evaluation board which contains two PCIe-Edge
fingers, one for PCIe-B(gen5x8) and one for CPM(dual gen5x8, gen5x16).
Each of the ports can operate in endpoint or root port mode. This allows
the single card to be used for both root port, endpoint, and switch modes.
The board is designed in the similar manner as others Versal boards. It
means board also have ZynqMP Zu4 System Controller which is described in a
separate file.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/59d3b1f7e785bc65518b465e5122fd2787616a93.1695808407.git.michal.simek@amd.com
System controllers are pretty much the same on the all boards that's why
use autodetection based on i2c eeprom. This should end up with having only
one BSP for all SCs with only DT overlays to cover different i2c
structures.
All MIOs are fixed by the spec that's why not a problem to description
pinctrl setting.
Apart from eth phy reset, it also set proper phy delays.
The TI DP83867 PHY datasheet says:
T1: Post RESET stabilization time == 195us
T3: Hardware configuration pins transition to output drivers == 64us
T4: RESET pulse width == 1us
So with a little overhead set 'reset-assert-us' to 100us (T4) and
'reset-deassert-us' to 280us (T1+T3).
NOTE: The tuning of TI DP83867 phy reset delay is derived from linux
upstream commit: 5dbadc848259(arm64: dts: fsl: add support for Kontron
pitx-imx8m board).
i2c structure on Xilinx Versal evaluation platforms contain a lot of
devices but also connection to connectors like SFP. Because of this
complicated structure with also all level shifters, i2c muxes, etc. not all
devices are able to reliably work on 400kHz even if they are compatible
with this speed. That's why set i2c frequency to 100KHz to increase
reliability of the i2c bus.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/c8092340f92144f0cc9096194198f227015bc013.1695808407.git.michal.simek@amd.com
Linux requires to describe nand structure under nand controller.
If it is not described nand device is not detected by Linux.
Error shown by Linux kernel:
pl35x-nand-controller e1000000.nand-controller: Incorrect number of NAND chips (0)
pl35x-nand-controller: probe of e1000000.nand-controller failed with error -22
When wired:
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAEAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/3fcd68ccdfed5e6c079681e3b29e06583ec8a375.1695378830.git.michal.simek@amd.com
Some boards are using one mdio bus which holds multiple phys and also
boards are using mdio node for bus description. That's why there are cases
where address/size-cells are unnecessary which is also reported by make W=1
dtbs. That's why remove them from zynqmp.dtsi and let board DTSes to handle
it based on used description.
Error log:
/axi/ethernet@ff0e0000: unnecessary #address-cells/#size-cells without
"ranges" or child "reg" property
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/02f308c774d4f2a798a9a8c066824114a19841a7.1695378830.git.michal.simek@amd.com
For Xilinx ZynqMP SOC new parameter was added and now it can
set 7 parameters for its pins. Pinmux status command will
print the status of these parameters for each pin. But
current print buffer length is only 80 characters long, increase it
to 90 to print all the parameters without truncation.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20230920030006.6488-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
- Add Board: rk3568 Bananapi R2Pro;
- Update pcie bifurcation support;
- dwc_eth_qos controller support for rk3568 and rk3588;
- Compressed binary support for U-Boot on rockchip platform;
- dts and config updates for different board and soc;
[ trini: Fix conflict on include/spl.h ]
Signed-off-by: Tom Rini <trini@konsulko.com>
A RK8XX PMIC is typically using i2c0 on RK356x devices. Add bootph-all
to required pinctrl nodes to simplify use of the prevent booting on
power plug-in option in SPL.
With the following Kconfig options and nodes in u-boot.dtsi the prevent
booting on power plug-in option can work in SPL.
CONFIG_ROCKCHIP_RK8XX_DISABLE_BOOT_ON_POWERON=y
CONFIG_SPL_I2C=y
CONFIG_SPL_POWER=y
CONFIG_SPL_PINCTRL=y
CONFIG_SPL_PMIC_RK8XX=y
&i2c0 {
bootph-pre-ram;
};
&rk817 {
bootph-pre-ram;
regulators {
bootph-pre-ram;
};
};
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The commit 30975fb73d ("rockchip: Add option to prevent booting on
power plug-in") introduce an option to prevent booting a device when the
device was powered on due to power plug-in instead of pressing a power
button.
This feature works by checking the power-on source during PMIC probe
and powers off the device if power-on source was power plug-in.
This check currently runs very late at PMIC probe in U-Boot proper.
Fix so that the power-on source check can work at probe time in SPL.
Also enable probe after bind and remove the PMIC banner in SPL.
With this we can use ROCKCHIP_RK8XX_DISABLE_BOOT_ON_POWERON and
SPL_PMIC_RK8XX to power off the device very quickly after TPL instead
of after TF-A and U-Boot proper has been loaded and run.
DDR V1.18 f366f69a7d typ 23/07/17-15:48:58
ln
LP4/4x derate en, other dram:1x trefi
ddrconfig:7
LPDDR4X, 324MHz
BW=32 Col=10 Bk=8 CS0 Row=17 CS1 Row=17 CS=2 Die BW=16 Size=8192MB
change to: 324MHz
clk skew:0x64
change to: 528MHz
clk skew:0x58
change to: 780MHz
clk skew:0x58
change to: 1056MHz(final freq)
clk skew:0x40
out
Power Off due to plug-in event
Fixes: 30975fb73d ("rockchip: Add option to prevent booting on power plug-in")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
With PMIC_RK8XX, SYSRESET and CMD_POWEROFF options enabled it is
possible to power down a board using the poweroff command and turn the
board back on using a power button.
Enable the poweroff command on RK356x boards that have a button wired
to PMIC pwron.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Select SYSRESET_CMD_POWEROFF to use the sysreset implementation of the
poweroff command when PMIC_RK8XX is enabled.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
all rk3308 boards should use their own dtb file.
also, change fdt_addr_r to avoid following error:
"ERROR: Did not find a cmdline Flattened Device Tree"
it happens on Radxa ROCK Pi S (256MB/512MB) with kernel built from
Radxa BSP.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Without DOS_PARTITION support U-Boot is not able to boot an OS stored
into an SD card with MBR partitions table. This is still a quite common
case so add DOS_PARTITION (only for U-Boot proper build) to Rockchip
RK3308 EVB, Radxa ROCK Pi S and Firefly roc-rk3308-cc boards: they are
the only RK boards missing of DOS_PARTITION.
Reported-by: Jayantajit Gogoi <jayanta.gogoi525@gmail.com>
Signed-off-by: Massimo Pegorer <massimo.pegorer+oss@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add Bananapi R2 Pro board.
tested:
- sdcard
- both front usb-ports
- sata
- wan-port
lan-ports are connected to mt7531 switch where driver needs to be
separated from mtk ethernet-driver.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Enable DWC_ETH_QOS_ROCKCHIP and related PHY driver on RK3588 boards that
have an enabled gmac node and drop ETH_DESIGNWARE and GMAC_ROCKCHIP for
remaining RK3588 boards.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable DWC_ETH_QOS_ROCKCHIP and related PHY driver on RK356x boards that
have an enabled gmac node.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add rk_gmac_ops and other special handling that is needed for GMAC to
work on RK3588.
rk_gmac_ops was ported from linux commits:
2f2b60a0ec28 ("net: ethernet: stmmac: dwmac-rk: Add gmac support for rk3588")
88619e77b33d ("net: stmmac: rk3588: Allow multiple gmac controller")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add a new glue driver for Rockchip SoCs, i.e RK3568, with a GMAC based
on Synopsys DWC Ethernet QoS IP.
rk_gmac_ops was ported from linux commit:
3bb3d6b1c195 ("net: stmmac: Add RK3566/RK3568 SoC support")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
If LZMA Compression support is enabled, LZMA compressed U-Boot
binary will be placed at a specified RAM location which is
defined at CONFIG_SYS_LOAD_ADDR and will be assigned as the
source address.
image_decomp() function, will decompress the LZMA compressed
U-Boot binary which is placed at source address(CONFIG_SYS_LOAD_ADDR)
to the default CONFIG_SYS_TEXT_BASE location.
spl_load_fit_image function will load the decompressed U-Boot
binary, which is placed at the CONFIG_SYS_TEXT_BASE location.
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
If GZIP Compression support is enabled, GZIP compressed U-Boot binary
will be at a specified RAM location which is defined at
CONFIG_SYS_LOAD_ADDR and will be assign it as the source address.
gunzip function in spl_load_fit_image ,will decompress the GZIP
compressed U-Boot binary which is placed at
source address(CONFIG_SYS_LOAD_ADDR) to the default
CONFIG_SYS_TEXT_BASE location.
spl_load_fit_image function will load the decompressed U-Boot
binary, which is placed at the CONFIG_SYS_TEXT_BASE location.
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update and improve documentation about build steps for SoCs that
require using TF-A and TPL binaries provided by Rockchip, such as
rk3308. Add rk3308 boards case to rST document. Add ROCK Pi S in
the list of supported boards. Minor page format improvements.
Signed-off-by: Massimo Pegorer <massimo.pegorer+oss@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There is no support to initialize DRAM on rk3308 SoC using U-Boot
TPL or SPL, and therefore an external TPL binary must be used to
package a bootable u-boot-rockchip.bin image.
Default ROCKCHIP_EXTERNAL_TPL to yes if ROCKCHIP_RK3308.
Remove useless TPL_SERIAL.
Signed-off-by: Massimo Pegorer <massimo.pegorer+oss@gmail.com>
Tested-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a minimal generic RK3566/RK3568 board that only have eMMC and SDMMC
enabled. This defconfig can be used to boot from eMMC or SD-card on most
RK3566/RK3568 boards that follow reference board design.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Port the Rockchip IO-domain driver for RK3568 from linux.
The driver auto probe after bind to configure IO-domain based on the
regulator voltage. Compared to the linux driver this driver is not
notified about regulator voltage changes and only configure IO-domain
based on the initial voltage autoset by the regulator.
It is not recommended to enable MMC_IO_VOLTAGE or the mmc signal voltage
and IO-domain may end up out of sync.
Based on the linux commit 28b05a64e47c ("soc: rockchip: io-domain: add
rk3568 support").
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The voltage value for switchout converters is always reported as 0 uV.
When the switch is enabled, it's voltage is same as input supply.
Fix this by implementing get_value for switchout converters.
Fixes: ee30068fa5 ("power: pmic: rk809: support rk809 pmic")
Signed-off-by: shengfei Xu <xsf@rock-chips.com>
[jonas@kwiboo.se: fix checkpatch error, update commit message]
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Information from the first range group is always used to calculate the
voltage returned for buck converters. This may result in wrong voltage
reported back to the regulator_get_value caller.
Traverse all the possible BUCK ranges to fix this issue.
Fixes: addd062bea ("power: pmic: rk816: support rk816 pmic")
Fixes: b62280745e ("power: pmic: rk805: support rk805 pmic")
Fixes: b4a35574b3 ("power: pmic: rk817: support rk817 pmic")
Fixes: ee30068fa5 ("power: pmic: rk809: support rk809 pmic")
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
[jonas@kwiboo.se: fix checkpatch error, simplify buck get_value, update commit message]
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
With the commit 4fcba5d556 ("regulator: implement basic reference
counter"), keeping regulator enablement in balance become more important.
Calling regulator_autoset multiple times on a fixed regulator increase
the enable count for each call, resulting in an unbalanced enable count.
Introduce a AUTOSET_DONE flag and use it to mark that autoset has run
for the regulator. Return -EALREADY on any subsequent call to autoset.
This fixes so that the enable count is only ever increased by one per
regulator for autoset.
Fixes: 4fcba5d556 ("regulator: implement basic reference counter")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable missing PCIe Kconfig options now that PCIe bifurcation is fixed
to make use of the two on-board RTL8125B and the M.2 slot on NanoPi R5C
and NanoPi R5S.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update and sync Kconfig options for NanoPi R5C and NanoPi R5S with other
RK3568 boards.
SPL_FIT_SIGNATURE is enabled to add a checksum validation of the FIT
payload, also add LEGACY_IMAGE_FORMAT to keep boot scripts working.
OF_SPL_REMOVE_PROPS, SPL_DM_SEQ_ALIAS and SPL_PINCTRL change ensure
pinctrl for eMMC, SD-card and UART2 is applied in SPL.
MMC_HS200_SUPPORT and SPL counterpart is enabled to speed up eMMC load
times from on-board eMMC 5.1 modules.
Drop remaining unused or unsupported options to sync with other RK3568
boards.
Also sync device tree from linux v6.4 and drop u-boot,spl-boot-order and
use the default from rk356x-u-boot.dtsi.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Route signal from comb PHY instead of PCIe3 PHY to PCIe1l0 and PCIe1l1.
Fixes use of pcie2x1l0 on ROCK 5B.
Code imported from mainline linux driver.
Fixes: c5b4a012bc ("phy: rockchip: naneng-combphy: Support rk3588")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for the RK3588 variant to the driver.
Code imported almost 1:1 from mainline linux driver.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Configure aggregation or bifurcation mode on RK3568 based on the value
of data-lanes property.
Code imported almost 1:1 from mainline linux driver.
Fixes: 6ec62b6ca6 ("phy: rockchip: Add Rockchip Synopsys PCIe 3.0 PHY")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a phy_init ops in preparation for upcoming support of a RK3588
variant in the driver.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Change to use clk_bulk API and syscon_regmap_lookup_by_phandle to
simplify in preparation for upcoming support of a RK3588 variant.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Set number of lanes and link width speed control register based on the
num-lanes property.
Code imported almost 1:1 from dw_pcie_setup in mainline linux.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
To quote the author:
This series tidies up SPL a little and adds some core ofnode functions
needed to support Universal Payload. It also includes a few minor
fix-ups for sandbox.
For SPL the changes include CONFIG naming, removing various #ifdefs and
tidying up the FIT code.
One notable piece of the ofnode improvements is support for flattening a
livetree. This should be useful in future as we move FDT fixups to use
the ofnode API.
The PCI helpers read only the base address for a PCI region. In some cases
the size is needed as well, e.g. to pass along to a driver which needs to
know the size of its register area.
Update the functions to allow the size to be returned. For serial, record
the information and provided it with the serial_info() call.
A limitation still exists in that the size is not available when OF_LIVE
is enabled, so take account of that in the tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function cannot return true if PCI is not enabled, since no PCI
devices will have been bound. Add a check for this to reduce code size
where it is used.
Signed-off-by: Simon Glass <sjg@chromium.org>
The spl_phase() function indicates whether U-Boot is in SPL and before
or after relocation. But sometimes it is useful to check for SPL with
zero code-size impact. Since spl_phase() checks the global_data flags,
it does add a few bytes.
Add a new spl_in_proper() function to check if U-Boot proper is
running, regardless of the relocation status.
Signed-off-by: Simon Glass <sjg@chromium.org>
This uses ARRAY_SIZE() but does not include the header file which declares
it. Fix this, so that command.h can be included without common.h
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Typically the bloblist is set up after the devicetree is present. This
makes sense because bloblist may use malloc() to allocate the space it
needs.
However sometimes the devicetree itself may be present in the bloblist.
In that case it is at a known location in memory so we can init the
bloblist very early, before devicetree.
Add a flag to indicate whether the bloblist has been inited. Add a
function to init it only if needed. Use that in the init sequence.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this down by 4KB so that it is large enough to hold the devicetree.
Also fix up the devicetree address in the documetation while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
We should not read this unless requested. Make it conditional on the
option being provided.
Add some debugging to show the state being written.
Signed-off-by: Simon Glass <sjg@chromium.org>
This currently relies on sandbox attempting to read a state file. At
present it always does, even when there is no state file, in which case it
fails, but still inits the EC.
That is a bug, so update this driver to set the current image always, even
if no state is read.
Signed-off-by: Simon Glass <sjg@chromium.org>
This should not happen in the argument-parsing function. Move it to the
main program.
Add some debugging for reading/writing.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a few simple tests for getting the root node, since this is handled
as a special case in the implementation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for writing a single 64-bit value into a property.
Repurpose the existing tests to handle this case too.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add functions to write a boolean property. This involves deleting it if
the value is false.
Add a new ofnode_has_property() as well. Add a comment about the behaviour
of of_read_property() when the property value is empty.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a way to flatten a devicetree into binary form. For livetree this
involves generating the devicetree using fdt_property() and other calls.
For flattree it simply involves providing the buffer containing the tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a function to copy a node to another place under a new name. This is
useful at least for testing, since copying a test node with existing
properties is easier than writing the code to generate it all afresh.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add comments to the functions where the test name does not indicate what
is being tested. Rename functions in a few cases, so that a search for the
function will also file its test.
Signed-off-by: Simon Glass <sjg@chromium.org>
We need the UT_TESTF_SCAN_FDT flag set for these tests to run with flat
tree. In some cases it is missing, so add it.
Signed-off-by: Simon Glass <sjg@chromium.org>
The bloblist should not be finalised until the image is fully set up.
This allows any final handoff information to be included in the bloblist.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than open-coding the property names, use the existing constants
provided for this purpose. This better aligns the simple-FIT code with
the full FIT implementation.
Signed-off-by: Simon Glass <sjg@chromium.org>
For some reason this code was put in the main spl.c file. Move it out
to the FIT implementation where it belongs.
Signed-off-by: Simon Glass <sjg@chromium.org>
We have two functions called spl_load_fit_image(), one in spl.c and one in
spl_fit.c
Rename the second one, to indicate that it relates to simple FIT parsing,
rather than the full version.
Signed-off-by: Simon Glass <sjg@chromium.org>
This feature has some helpers in its header file so that its functions
resolve to nothing when the feature is disabled. Add a few more and use
these to simplify the code.
With this there are no more #ifdefs in board_init_r()
Signed-off-by: Simon Glass <sjg@chromium.org>
Move the useful help to Kconfig.
Drop mention of CONFIG_SYS_MALLOC_SIMPLE since it doesn't exist.
Correct a 'CONFIGSYS_MALLOC_F_LEN' typo
Signed-off-by: Simon Glass <sjg@chromium.org>
Use CONFIG_SYS_MALLOC_F instead to of CONFIG_SYS_MALLOC_F_LEN to
determine whether pre-relocation malloc() is enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use the new SPL/TPL/VPL_SYS_MALLOC_F symbols to determine whether the
malloc pool exists.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Enable CONFIG_TPL_SYS_MALLOC_F for boards which have a non-zero value
for CONFIG_TPL_SYS_MALLOC_F_LEN
Note that the default is yes in most cases, so no changes are needed to
board defconfig options.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable CONFIG_SPL_SYS_MALLOC_F for boards which have a non-zero value
for CONFIG_SPL_SYS_MALLOC_F_LEN
Note that the default is yes in most cases, so no changes are needed to
board defconfig options.
Signed-off-by: Simon Glass <sjg@chromium.org>
For U-Boot proper we have CONFIG_SYS_MALLOC_F which indicates that a
malloc() pool is available before relocation.
For SPL we only have CONFIG_SPL_SYS_MALLOC_F_LEN which indicates the
size of the pool.
In various places we use CONFIG_SPL_SYS_MALLOC_F_LEN == 0 to indicate
that there is no pool.
This differing approach is confusing. Add a new CONFIG_SPL_SYS_MALLOC_F
symbol for SPL (and similarly for TPL and VPL). Tidy up the Kconfig
help for clarity.
For now these symbols are not used. That is cleaned up in the following
patches.
Signed-off-by: Simon Glass <sjg@chromium.org>
These symbols do not (yet) exist, so drop the usage of them in the
serial Kconfig file. It has no effect.
Signed-off-by: Simon Glass <sjg@chromium.org>
This code is pretty ugly, with many #ifdefs
There are quite a lot of IH_OS_U_BOOT values so the compiler struggles
to create a jump table here. Also, most of the options are normally
disabled.
Change it to an else...if construct instead. Add an accessor for the
spl_image field behind an #ifdef to avoid needing #ifdef in the C code.
Signed-off-by: Simon Glass <sjg@chromium.org>
It doesn't make sense to have some boards do this differently. Drop the
condition in the hope that the maintainers can figure out any run-time
problems.
This has been tested on qemu-ppce500
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Rename this so that SPL is first, as per U-Boot convention. Also add
PAYLOAD_ since this is where in memory the parameters for the payload
have been stored.
Signed-off-by: Simon Glass <sjg@chromium.org>
We like to put the SPL first so it is clear that it relates to SPL. Rename
various malloc-related options which have crept in, to stick to this
convention.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Svyatoslav Ryhel <clamor95@gmail.com>
+ ae350: modify memory layout and target name
+ ae350: use generic RISC-V timer driver in S-mode
+ Support bootstage report for RISC-V
+ Support C extension exception command for RISC-V
+ Add Starfive timer support
Sync k3-j721e DTS with kernel.org v6.6-rc1.
* Use mcu_timer0 defined in k3-j721e-mcu-wakeup.dtsi and remove
timer0, we have its clocks set up in clk-data now
* Remove hbmc node as support is buggy and needs to be fixed
* Remove aliases and chosen node, use them from Kernel
* Remove /delete-property/ and clock-frequency from sdhci,
usbss, and mcu_uart nodes as we have them in clk and dev data
* Remove dummy_clocks as they are not needed
* Remove cpsw node as it is not required since it has been fixed
in U-Boot
* Remove pcie nodes, they are not needed
* Remove mcu_i2c0 as it is used for tps659413 PMIC in j721e-sk
for which support is not yet added
* Change secproxy nodes to their Linux definitions
* Remove overriding of ti,cluster-mode in MAIN R5 to default to
lockstep mode same as Kernel
* Retain tps6594 node as TPS6594 PMIC support is still under
review in the Kernel [1], cleanup will be taken post its merge
[1] https://lore.kernel.org/all/20230810-tps6594-v6-0-2b2e2399e2ef@ti.com/
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Manorit Chawdhry <m-chawdhry@ti.com>
Get rid of k3-j721e-r5-*-u-boot.dtsi as it is not
necessary. Change the inclusion hierarchy to be as follows:
k3-j721e-<board>.dts---
-
-->k3-j721e-r5-<board>.dts
-
k3-j721e-<board>-u-boot.dtsi---
Reason for explicitly mentioning the inclusion of -u-boot.dtsi in code
although it could've been automatically done by U-Boot is to resolve
some of the dependencies that R5 file requires.
Also remove duplicate phandles while making this shift as well as remove
firmware-loader as it serves no purpose without "phandlepart" property.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Kernel commit d93036b47f35 ("arm64: dts: ti: k3-j721e-mcu_wakeup: Add
HyperBus node") was merged to kernel without its dependent patch [1].
Similar fix is needed in U-Boot, and hbmc currently breaks boot. Till
this gets fixed in U-Boot, disable the config by default so that the
hbmc probe that happens in board/ti/j721e/evm.c will not take place
and lead to boot failure.
[1] https://lore.kernel.org/all/20230424184810.29453-1-afd@ti.com/
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
When setting up boot media to load the TIFS binary in legacy boot flow
(followed by J721E), get_timer() is called which calls dm_timer_init()
which then gets the tick-timer: mcu_timer0. mcu_timer0 uses k3_clks
(clock controller) and k3_pds (power controller) from the dmsc node that
forces probe of the ti_sci driver of TIFS that hasn't been loaded yet!
Running ti_sci_cmd_get_revision from the probe leads to panic since no
TIFS and board config binaries have been loaded yet. Resolve this by
moving ti_sci_cmd_get_revision to ti_sci_get_handle_from_sysfw as a
common point of invocation for both legacy and combined boot flows.
Before doing this, it is important to go through whether any sync points
exist where revision is needed before ti_sci_get_handle_from_sysfw is
invoked. Going through the code along with boot tests on both flows
ensures that there are none.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
When setting boot media to load the TIFS binary in legacy boot flow
(followed by J721E), get_timer() is called which eventually calls
dm_timer_init() to grab the tick-timer, which is mcu_timer0. Since we
need to set up the clocks before using the timer, move clk_k3 driver
probe before k3_sysfw_loader to ensure we have all necessary clocks set
up before.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Manorit Chawdhry <m-chawdhry@ti.com>
U-Boot uses mcu_timer0 as the tick-timer, so add it to device list.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Manorit Chawdhry <m-chawdhry@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Since commit [1] A53 u-boot proper is broken. This is because nodes
marked as 'bootph-pre-ram' are not available at u-boot proper before
relocation.
To fix this we mark all nodes in u-boot.dtsi as 'bootph-all'.
[1]
9e644284ab ("dm: core: Report bootph-pre-ram/sram node as pre-reloc after relocation")
Reported-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Since commit [1] A53 u-boot proper is broken.
This is because nodes marked as 'bootph-pre-ram' are
not available at u-boot proper before relocation.
To fix this we mark all nodes in sk-u-boot.dtsi as
'bootph-all'.
[1]
9e644284ab ("dm: core: Report bootph-pre-ram/sram node as pre-reloc after relocation")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
CPSW node needs PHY, MDIO, pinmux, DMA and INTC nodes.
Mark them as 'bootph-all' so they are available in all
pre-relocation phases.
Fixes below dts warnings:
<stdout>: Warning (reg_format): /bus@f4000/ethernet@8000000/mdio@f00/ethernet-phy@1:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
<stdout>: Warning (unit_address_vs_reg): /bus@f4000/ethernet@8000000/mdio@f00: node has a unit name, but no reg or ranges property
<stdout>: Warning (pci_device_reg): Failed prerequisite 'reg_format'
<stdout>: Warning (pci_device_bus_num): Failed prerequisite 'reg_format'
<stdout>: Warning (simple_bus_reg): Failed prerequisite 'reg_format'
<stdout>: Warning (i2c_bus_reg): Failed prerequisite 'reg_format'
<stdout>: Warning (spi_bus_reg): Failed prerequisite 'reg_format'
<stdout>: Warning (avoid_default_addr_size): /bus@f4000/ethernet@8000000/mdio@f00/ethernet-phy@1: Relying on default #address-cells value
<stdout>: Warning (avoid_default_addr_size): /bus@f4000/ethernet@8000000/mdio@f00/ethernet-phy@1: Relying on default #size-cells value
<stdout>: Warning (avoid_unnecessary_addr_size): Failed prerequisite 'avoid_default_addr_size'
<stdout>: Warning (unique_unit_address): Failed prerequisite 'avoid_default_addr_size'
<stdout>: Warning (msi_parent_property): /bus@f4000/bus@48000000/dma-controller@485c0100:msi-parent: Could not get phandle node for (cell 0)
<stdout>: Warning (msi_parent_property): /bus@f4000/bus@48000000/dma-controller@485c0000:msi-parent: Could not get phandle node for (cell 0)
<stdout>: Warning (phys_property): /bus@f4000/ethernet@8000000/ethernet-ports/port@2:phys: Could not get phandle node for (cell 0)
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Since commit [1] A53 u-boot proper is broken.
This is because nodes marked as 'bootph-pre-ram' are
not available at u-boot proper before relocation.
To fix this we mark all nodes in sk-u-boot.dtsi as
'bootph-all'.
Move cbass_mcu node to -r5-sk.dts as it is only required
for R5 SPL.
[1]
9e644284ab ("dm: core: Report bootph-pre-ram/sram node as pre-reloc after relocation")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
CPSW node needs PHY, MDIO, pinmux, DMA and INTC nodes.
USB and MMC nodes need pinmux.
Mark them as 'bootph-all' so they are available in all
pre-relocation phases.
Fixes below dts warning:
<stdout>: Warning (dmas_property): /bus@f4000/ethernet@8000000:dmas: Could not get phandle node for (cell 0)
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Since commit [1] A53 u-boot proper is broken.
This is because nodes marked as 'bootph-pre-ram' are
not available at u-boot proper before relocation.
To fix this we mark all nodes in sk-u-boot.dtsi as
'bootph-all'.
Move vtt_supply and cbass_mcu node to -r5-evm.dts as
it is only required for R5 SPL.
[1]
9e644284ab ("dm: core: Report bootph-pre-ram/sram node as pre-reloc after relocation")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
This does not move configs anymore, but queries them, based on a database
it can build. Rename the tool to better reflect its purpose.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since moveconfig now just does what it is told (build database or sync
defconfigs) we don't need to print what it is doing. Drop this info, which
is of very little use.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than printing all the failed boards, which are now easily visible
on the terminal, just show a summary. Sort it by defconfig and drop the
'_defconfig' suffix.
Signed-off-by: Simon Glass <sjg@chromium.org>
Show the number of accumulated failures when processing. Use a shorter
format with colour.
An unwanted space appears before the defconfig name on every item except
the last. Fix that while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use the existing terminal code to handle ANSI colours. Enable colour by
default if the output is going to a terminal.
Signed-off-by: Simon Glass <sjg@chromium.org>
When the process is finished, moveconfig leaves a line saying that all
boards were processed (for better or worse). Drop this, since it is
unncessary.
Future work will provide a summary at the end instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Output a single line in the case where the defconfig only has one line
of output. Show the name without the _defconfig suffix, since that is the
same for all boards.
Use a list for the log so it is easier to process at the end.
Signed-off-by: Simon Glass <sjg@chromium.org>
There is no point in listing a board if everything went well. It makes it
harder to see the failures, particularly on a fast machine.
Suppress output unless something actually happened.
Drop the 'Syncing by savedefconfig' since this is selected by the -s and
is the same for all boards in this mode.
Signed-off-by: Simon Glass <sjg@chromium.org>
As a step towards cleaning out old code, drop most of the code that moves
CONFIG options to Kconfig. This includes parse_one_config().
Drop the ACTION_... values as well, since they are no-longer used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Cleaning up the README and config.h files are not needed now, since we
don't have any CONFIG options to convert. Drop this code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use the recommended new way of setting a thread to be a daemon.
This avoids a warning:
DeprecationWarning: setDaemon() is deprecated, set the daemon attribute
instead
Signed-off-by: Simon Glass <sjg@chromium.org>
STM32 MCU:
_ alignment with kernel DT v6.5 for stm32f429 and stm32f746
_ rework way of displaying ST logo for stm32f746-disco and stm32f769-disco
STM32 MPU:
_ alignment with kernel DT v6.6-rc1
_ add RNG support for stm32mp13
_ add USB, USB boot and stm32prog command support for stm32mp13
_ add support of USART1 clock for stm32mp1
_ only print RAM and board code with SPL_DISPLAY_PRINT flag for
stm32mp1
_ rename update_sf to dh_update_sd_to_sf and add dh_update_sd_to_emmc
for stm32mp15xx DHCOR
[ Fix merge conflict at board/st/common/stm32mp_dfu.c ]
Signed-off-by: Tom Rini <trini@konsulko.com>
split the file stm32mp_dfu.c in two files to simplify the Makefile
- stm32mp_dfu.c: required by CONFIG_SET_DFU_ALT_INFO
- stm32mp_dfu_virt.c: required by CONFIG_DFU_VIRT for stm32prog
command or VIRT device for PMIC for CONFIG_SET_DFU_ALT_INFO.
This patch also remove some remaining #ifdef CONFIG
and avoid compilation error when CONFIG_SET_DFU_ALT_INFO is not
activated.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Activate the command stm32prog with CONFIG_CMD_STM32MPROG.
The CONFIG_SET_DFU_ALT_INFO is also activated to support
the required weak functions for the DFU virtual backen defined in
board/st/common/stm32mp_dfu.c.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
stm32mp135f-dk board has a type-c connector to retrieve the connection
state. For now, simply force an active peripheral mode in u-boot for
flashing.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add script which installs U-Boot binaries from SD card to eMMC
and makes the eMMC bootable.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Align the script name with DH i.MX8MP DHCOM script name. Add
backward compatibility script to avoid breaking user scripts.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add USART1 clock parents and mux configuration. This allows
support for configuring the USART1 as the serial console in
SPL and U-Boot via device tree. Without this patch the SPL
with usart1 serial console enabled crashes because it can
not find the clock specified in the device tree for usart1.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Ensure that the SoM and board code information is only printed when
CONFIG_SPL_DISPLAY_PRINT is set.
Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Ensure that the RAM configuration line is only printed when
CONFIG_SPL_DISPLAY_PRINT is set.
Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Seed errors can occur when using the hardware RNG. Implement the
sequences to handle them. This avoids irrecoverable RNG state.
Try to conceal seed errors when possible. If, despite the error
concealing tries, a seed error is still present, then return an error.
A clock error does not compromise the hardware block and data can
still be read from RNG_DR. Just warn that the RNG clock is too slow
and clear RNG_SR.
Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Default embed this configuration. If OP-TEE PTA RNG is exposed, it means
that the RNG is managed by the secure world. Therefore, the RNG node
should be disabled in the device tree as an access would be denied
by the hardware firewall.
Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The patch removes the legacy mode of displaying the ST logo and adopts
the approach introduced by the commit 284b08fb51 ("board: stm32mp1: add
splash screen with stmicroelectronics logo").
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The patch removes the legacy mode of displaying the ST logo and adopts
the approach introduced by the commit 284b08fb51 ("board: stm32mp1: add
splash screen with stmicroelectronics logo"). It was necessary to use a
specific logo for the stm32f746-disco board.
Furthermore, the previous version didn't properly center the logo, hiding
its upper part.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The patch applies the changes from Linux commit 10a970bc3ebfa ("ARM: dts:
stm32: support display on stm32f746-disco board") and removes the same
settings from stm32f746-disco-u-boot.dtsi.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
commit e4e724099f04072053cf411456e3e9aae48c4af1 Linux upstream.
In the schematics of document UM1907, the power supply for the micro SD
card is the same 3v3 voltage that is used to power other devices on the
board. By generalizing the name of the voltage regulator, it can be
referenced by other nodes in the device tree without creating
misunderstandings.
This patch is preparatory for future developments.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The patch applies the changes from Linux commit 008ef8b3a1a00 ("Add LTDC
(Lcd-tft Display Controller) support") and removes the same settings
from stm32f746-disco-u-boot.dtsi.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
commit 7a5f349e592c254f3c1ac34665b6c3905576efc2 Linux upstream.
The patch replaces the number 12 with the appropriate numerical constant
already defined in the file stm32f7-rcc.h.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
commit 0920ccdf41e3078a4dd2567eb905ea154bc826e6 Linux upstream.
Add support for bxcan (Basic eXtended CAN controller) to STM32F746. The
chip contains three CAN peripherals, CAN1 and CAN2 in dual peripheral
configuration and CAN3 in single peripheral configuration:
- Dual CAN peripheral configuration:
* CAN1: Primary bxCAN for managing the communication between a secondary
bxCAN and the 512-byte SRAM memory.
* CAN2: Secondary bxCAN with no direct access to the SRAM memory.
This means that the two bxCAN cells share the 512-byte SRAM memory and
CAN2 can't be used without enabling CAN1.
- Single CAN peripheral configuration:
* CAN3: Primary bxCAN with dedicated Memory Access Controller unit and
512-byte SRAM memory.
-------------------------------------------------------------------------
| features | CAN1 | CAN2 | CAN 3 |
-------------------------------------------------------------------------
| SRAM | 512-byte shared between CAN1 & CAN2 | 512-byte |
-------------------------------------------------------------------------
| Filters | 26 filters shared between CAN1 & CAN2 | 14 filters |
-------------------------------------------------------------------------
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/all/20230427204540.3126234-6-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Powering off the SiFive HiFive Unmatched board is supported both via the
SBI and GPIO sysreset drivers. See device-tree entry
compatible = "gpio-poweroff".
Enable the poweroff command.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The Andes PLMT driver directly accesses the mtime MMIO region,
indicating its intended use in the M-mode boot stage. However,
since U-Boot proper (S-mode) also uses the PLMT driver, we need
to specifically mark the region as readable through PMPCFGx (or
S/U-mode read-only shared data region for Smepmp) in OpenSBI.
Granting permission for this case doesn't make sense. Instead,
we should use the generic RISC-V timer driver to read the mtime
through the TIME CSR. Therefore, we add the SPL_ANDES_PLMT_TIMER
config, which ensures that the PLMT driver is linked exclusively
against M-mode U-Boot or U-Boot SPL binaries.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Most boards don't enable the pre-console buffer. So we will not see any
early messages. OpenSBI 1.3 provides us with the debug console extension
that can fill this gap.
For S-Mode U-Boot enable CONFIG_DEBUG_UART by default.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
A 16 bit aligned instruction should generated an exception if the C
extension is not available.
Provide an 'extension ialign16' command for testing exception handling.
For testing build qemu-riscv64_defconfig with CONFIG_RISCV_ISA_C=n
and run with
qemu-system-riscv64 -M virt -bios u-boot -nographic -cpu rv64,c=false
=> exception ialign16
Unhandled exception: Instruction address misaligned
EPC: 0000000087719138 RA: 0000000087719218 TVAL: 000000008771913e
EPC: 0000000080020138 RA: 0000000080020218 reloc adjusted
Code: 0113 0101 8067 0000 0113 ff01 3423 0011 (006f 0060)
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Eliminating the C extension on application processors is under
discussion.
Support emitting a compressed instruction. This will lead to an
illegal instruction exception if the C extension is not implemented.
For testing build qemu-riscv64_defconfig with CONFIG_RISCV_ISA_C=n
and run with
qemu-system-riscv64 -M virt -bios u-boot -nographic -cpu rv64,c=false
=> exception compressed
Unhandled exception: Illegal instruction
EPC: 0000000087731708 RA: 000000008773fe44 TVAL: 0000000000004501
EPC: 000000008001b708 RA: 0000000080029e44 reloc adjusted
Code: 0b93 0000 0493 0000 0993 0000 f06f ccdf (4501)
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
timer_get_boot_us function is required to record the boot stages as
us-based timestamp.
To get a micro-second time from a timer tick, this converts the
formula like below to avoid zero result of (tick / rate) part.
From: time(us) = (tick / rate) * 1000000
To : time(us) = (tick * 1000) / (rate / 1000)
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
timer_get_boot_us function is required to record the boot stages as
us-based timestamp.
To get a micro-second time from a timer tick, this converts the
formula like below to avoid zero result of (tick / rate) part.
From: time(us) = (tick / rate) * 1000000
To : time(us) = (tick * 1000) / (rate / 1000)
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Below warning can be occurred when CONFIG_BOOTSTAGE and
!CONFIG_SPL_BOOTSTAGE. It should be guarded by using CONFIG_IS_ENABLED
for SPL build.
arch/riscv/lib/bootm.c:46:9: warning: implicit declaration of
function 'bootstage_report'
46 | bootstage_report();
| ^~~~~~~~~~~~~~~~
| bootstage_error
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Set U-Boot environment storage eMMC device number to 0, to match
the new additions to DT /aliases node pulled in alongside Linux
6.5.3 DT synchronization.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize RZ R8A774E1 RZ/G2H DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize RZ R8A774C0 RZ/G2E DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize RZ R8A774B1 RZ/G2N DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize RZ R8A774A1 RZ/G2M DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Adam Ford <aford173@gmail.com>
Synchronize RZ R7S72100 RZ/A1 DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A779G0 V4H DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A779F0 S4 DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A779A0 E3 DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A77995 D3 DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A77990 E3 DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A77980 V3H DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A77970 V3M DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A77965 M3-N DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A77960 M3-W and R8A77961 M3-W+ DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A77951 H3 DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A7794 E2 DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A7791 M2-W and R8A7793 M2-N DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A7790 H2 DTs with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R8A774E1 RZ/G2H clock tables with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R8A774C0 RZ/G2E clock tables with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R8A774B1 RZ/G2N clock tables with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R8A774A1 RZ/G2M clock tables with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A779G0 V4H clock tables with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
The PLL2_VAR is not implemented yet and PLL2 is still configured
as regular PLL2 only.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A77960 M3-W and R8A77961 M3-W+ clock tables with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A7791 M2-W and R8A7793 M2-N clock tables with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A77960 M3-W and R8A77961 M3-W+ PFC tables with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A7791 M2-W and R8A7793 M2-N PFC tables with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Currently, the Renesas pin control driver supports pins that can switch
their I/O voltage levels between either 1.8V and 3.3V, or between 2.5V
and 3.3V. However, some SoCs have pins that can switch between 1.8V and
2.5V.
Add support for this by replacing the separate SH_PFC_PIN_CFG_IO_VOLTAGE
capability and voltage level flags by a 2-bit field, to cover three
possible I/O voltage switching options.
Ported from Linux kernel commit by Geert Uytterhoeven:
b88e733ac517 ("pinctrl: renesas: Add support for 1.8V/2.5V I/O voltage levels")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Rename pfc-r7s72100.c to pfc-rza1.c to match the file name with Linux.
Rename the Kconfig symbol to match.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Rename pfc-r8a7795.c to pfc-r8a77951.c to match the file name with Linux
and to indicate the PFC driver does not support R8A77950 H3 ES1.* .
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add compatible values to Ethernet PHY subnodes representing Micrel
KSZ9031 PHYs on R-Car Gen3 Salvator-X boards. This allows software
to identify the PHY model at any time, regardless of the state of
the PHY reset line.
This is a fix for missed addition of these properties on Salvator-X
boards.
Ported from Linux kernel commit 722d55f3a9bd810f3a1a31916cc74e2915a994ce .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Commit 65cc0e2a65 ("global: Move remaining CONFIG_SYS_* to CFG_SYS_*")
renamed CONFIG_SYS_UBOOT_START to CFG_SYS_UBOOT_START. Unfortunately,
this meant that the value was no longer available to the Makefile. This
caused imxrt to fail to boot. All the other boards that used this
variable were unaffected because they were using the default value
which is CONFIG_TEXT_BASE.
This commit converts CFG_SYS_UBOOT_START to Kconfig and sets the default
value to CONFIG_TEXT_BASE.
Suggested-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Suggested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Out-of-tree users could run an out-of-tree CI with limited coverage,
however it is convenient to be able to run the upstream CI from time
to time. To enable that we would need to change job rules to be able
to run on any GitLab event. Excerpt from GitLab documentation:
> Jobs with no rules default to except: merge_requests
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The test_event_base and test_event_probe unit tests use function
event_register() which depends on CONFIG_EVENT_DYNAMIC=y.
Fixes: 7d02645fe4 ("event: Add a simple test")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This old patch was marked as deferred. Bring it back to life, to continue
towards the removal of common.h
Move this out of the common header and include it only where needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
A '.update' extension does not get preserved by buildman, so change it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Michael Walle <michael@walle.cc>
The Kconfig and maintainer processing can take a while, sometimes 5
seconds or more. This skews the timing printed by buildmand when the build
completes. Start the clock when the threads start to avoid this problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Tom Rini <trini@konsulko.com>
Make a list of common output extensions and use it to ensure that the -k
option preserves all of these.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The output from "dm tree" or "dm uclass" is a bit annoying
if the number of devices available on the system is huge.
(This is especially true on sandbox when I debug some DM code.)
With this patch, we can specify the uclass name or the device
name that we are interested in in order to limit the output.
For instance,
=> dm uclass usb
uclass 121: usb
0 usb@1 @ 0bcff8b0, seq 1
uclass 124: usb
=> dm tree usb:usb@1
Class Index Probed Driver Name
-----------------------------------------------------------
usb 0 [ ] usb_sandbox usb@1
usb_hub 0 [ ] usb_hub `-- hub
usb_emul 0 [ ] usb_sandbox_hub `-- hub-emul
usb_emul 1 [ ] usb_sandbox_flash |-- flash-stick@0
usb_emul 2 [ ] usb_sandbox_flash |-- flash-stick@1
usb_emul 3 [ ] usb_sandbox_flash |-- flash-stick@2
usb_emul 4 [ ] usb_sandbox_keyb `-- keyb@3
If you want forward-matching against a uclass or udevice name,
you can specify "-e" option.
=> dm uclass -e usb
uclass 15: usb_emul
0 hub-emul @ 0bcffb00, seq 0
1 flash-stick@0 @ 0bcffc30, seq 1
2 flash-stick@1 @ 0bcffdc0, seq 2
3 flash-stick@2 @ 0bcfff50, seq 3
4 keyb@3 @ 0bd000e0, seq 4
uclass 64: usb_mass_storage
uclass 121: usb
0 usb@1 @ 0bcff8b0, seq 1
uclass 122: usb_dev_generic
uclass 123: usb_hub
0 hub @ 0bcff9b0, seq 0
uclass 124: usb
=> dm tree -e usb
Class Index Probed Driver Name
-----------------------------------------------------------
usb 0 [ ] usb_sandbox usb@1
usb_hub 0 [ ] usb_hub `-- hub
usb_emul 0 [ ] usb_sandbox_hub `-- hub-emul
usb_emul 1 [ ] usb_sandbox_flash |-- flash-stick@0
usb_emul 2 [ ] usb_sandbox_flash |-- flash-stick@1
usb_emul 3 [ ] usb_sandbox_flash |-- flash-stick@2
usb_emul 4 [ ] usb_sandbox_keyb `-- keyb@3
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Nodes with bootph-pre-sram/ram props are bound in multiple phases:
1. At TPL (bootph-pre-sram) or SPL (bootph-pre-ram) phase
2. At U-Boot proper pre-relocation phase
3. At U-Boot proper normal phase
However the binding and U-Boot Driver Model documentation indicate that
only nodes marked with bootph-all or bootph-some-ram should be bound in
the U-Boot proper pre-relocation phase.
Change ofnode_pre_reloc to report a node with bootph-pre-ram/sram prop
with a pre-reloc status only after U-Boot proper pre-relocation phase.
Also update the ofnode_pre_reloc documentation to closer reflect the
binding and driver model documentation.
This changes behavior of what nodes are bound in the U-Boot proper
pre-relocation phase. Change to bootph-all or add bootph-some-ram prop
to restore prior behavior.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Add bootstd support to 64-bit efi payload
- Fix a bug of missing setting size of initrd in pxeboot
- Allow Python packages to be dropped
- Reland "x86: Move FACP table into separate functions"
- Fixes for chromebook_link64 and chromebook_samus_tpl
- Fixes and improvements for coreboot
- x86 documentation updates
Add a little more detail as to why coreboot64 is preferred for booting
Linux distros.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Move this out of the main file since for simple users it is easier to
rely on standard boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Refresh the summary information so it is more up-to-date. Add links to
the coreboot and slimbootloader docs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
There is enough material that it makes sense to split this up into
several files. Create an x86/ directory for this purpose.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Make a note of where coreboot installed the SMBIOS tables so that we can
pass this on to EFI.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
U-Boot should set up the SMBIOS tables during startup, as it does on x86.
Ensure that it does this correctly on non-x86 machines too, by creating
an event spy for last-stage init.
Tidy up the installation-condition code while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Remember where these end up so that we can pass this information on to
the EFI layer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When 'usb stop' is run, doing 'bootflow scan' does not run the USB hunter
again so does not see any devices. Fix this by telling bootstd about the
state of USB.
Signed-off-by: Simon Glass <sjg@chromium.org>
When booted from coreboot, U-Boot does not build the SMBIOS tables, but
it should still pass them on to the OS. Add a new option which indicates
whether SMBIOS tables are present, however they were built.
Flip the ordering so that the dependency is listed first, which is less
confusing.
Adjust GENERATE_SMBIOS_TABLE to depend on this new symbol.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is not always the case that U-Boot builds the ACPI tables itself. For
example, when booting from coreboot, the ACPI tables are built by
coreboot.
Correct the Makefile condition so that U-Boot can pass on tables built
by a previous firmware stage.
Tidy up the installation-condition code while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At least on modern machines the write-back mechanism for the frame buffer
is quite slow when scrolling, since it must read the entire frame buffer
and write it back.
Enable the VIDEO_COPY feature to resolve this problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
These two builds are similar but have some different options for not good
reason. Line them up to be as similar as possible.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This is very annoying as it is quite slow on many machines. Also, U-Boot
has an existing 'preboot' mechanism to enable this feature if desired.
Drop this code so that it is possible to choose whether to init USB or
not.
Use the existing USE_PREBOOT mechanism instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The debug UART on modern machines uses a 32-bit wide transfer. Without
this, setting debug output causes a hang or no output. It is not obvious
(when enabling CONFIG_DEBUG_UART) that this is needed.
Enable 32-bit access to avoid this trap.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
If coreboot does not set up sysinfo for the UART, SPL currently hangs.
Use the DBG2 technique there as well. This allows coreboot64 to boot from
coreboot even if the console info is missing from sysinfo
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This is needed so we can find the DBG2 table provided by coreboot. Add a
Kconfig so it can be enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We don't read this information in 64-bit mode, since we don't have the
macros for doing it. Set it to Intel by default. This allows the TSC timer
to work correctly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Init errors in SPL are currently ignored by this function.
Change the code to init the CPU, reporting an error if something is wrong.
After that, look for the coreboot table.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Enable bootstd options and provide instructions on how to boot a linux
distro using coreboot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add these options to permit access to more disk types.
Add some documentation as well.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This driver is not actually built since a Kconfig was never created for
it.
Add a Kconfig (which is already implied by COREBOOT) and update the
implementation to avoid using unnecessary memory. Drop the #ifdef at the
top since we can rely on Kconfig to get that right.
To enable it (in addition to serial and video), use:
setenv stdout serial,vidconsole,cbmem
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[Modified the comment about overflow a little bit]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Coreboot changed a few years ago to include an overflow flag. Update the
structure to match this.
This comes from coreboot commit:
6f5ead14b4 ("mb/google/nissa/var/joxer: Update eMMC DLL settings")
Note: There are several implementations of this in coreboot. I have chosen
to follow the one in src/lib/cbmem_console.c
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When turning off CAR, set the flag to make sure that nothing tries to use
driver model in SPL before jumping to U-Bot proper, since its tables are
in CAR.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The current condition does not handle the samus_tpl case where it sets
up the RAM in SPL but needs to commit the MTRRs in U-Boot proper.
Add another case to handle this and update the comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When TPL has already set up the CPU, don't do it again. This existing
code actually has this backwards, so fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Make this depend on whether the address matches the offset, rather than
a particular board build. For samus_tpl we don't need to copy, for
example.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Make sure that CONFIG_X86_OFFSET_U_BOOT is the same as CONFIG_TEXT_BASE
as it is changing CONFIG_X86_OFFSET_U_BOOT
Samus boots into U-Boot proper in flash, not RAM. Also expand the SPL
malloc() size a little, to avoid an error.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Samus only takes 7 seconds but it is long enough to think it has hung. Add
a message about what it is doing, similar to the approach on coral.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
On x86 devices we use CAR (Cache-As-RAM) to hold the malloc() region in
SPL, since SDRAM is not set up yet. This means that driver model stores
its tables in this region.
When preparing to jump from SPL to U-Boot proper, we must disable CAR, so
that the CPU can uses the caches normally. This means that driver model
tables become inaccessible. From there until we jump to U-Boot proper, we
must avoid using driver model.
This is only a problem on boards which operate this way, for example
chromebook_link64
Add a flag to indicate that driver model is dead and should not be used.
It can be used in SPL to avoid hanging the machine.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Recent approach with FADT writer shows that there is
a room for subtle errors. Prevent this from happening
again by introducing acpi_add_fadt() helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Declare the global_data pointer at the top of the file, to avoid an
error:
arch/x86/include/asm/global_data.h:143:35: error: a label can
only be part of a statement and a declaration is not a statement
board/coreboot/coreboot/coreboot.c:60:2: note: in expansion of macro
‘DECLARE_GLOBAL_DATA_PTR’
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mike Frysinger <vapier@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When building in a portage chroot, we do not have the environment needed
to build pylibfdt. It is instead build as a separate package.
Provide a build option to tell U-Boot to skip this part of the build. We
still need it to use binman, etc. but don't need it to build its
dependencies.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mike Frysinger <vapier@chromium.org>
[s/build bytes/builds bytes in tools.rst]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
U-Boot at VirtualBox must load Linux and boot configuration from disk devices.
Here the discs at AHCI (scsi) bus are used to load the needed boot data.
Signed-off-by: Thomas Mittelstaedt <thomas.mittelstaedt@de.bosch.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[Added 'efi-payload64' tag and rebased on top of u-boot/master]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
This avoids an error when ifdef CONFIG_PCI is changed to
if CONFIG_IS_ENABLED(PCI)
Signed-off-by: Troy Kisky <troykiskyboundary@gmail.com>
[Rebased on top of u-boot/master]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Xilinx changes for v2024.01-rc1
clk:
- Dont return error when assigned-clocks is empty or missing
dm:
- Support reading a single indexed u64 value
- Add support for reading bootscript address/flash address from DT
cmd:
- Fix flash_is_unlocked API
fpga:
- Define fpga_load() for debug build
global:
- U-Boot project name cleanup (next2)
net:
- zynq_gem: Use generic_phy_valid() helper
- axienet: Convert to ofnode functions
- gmii2rgmii: Read bridge address from DT
pytest:
- skip tpm2_startup when env__tpm_device_test_skip=True
spi-nor:
- Add mx25u25635f support
- zynqmp_qspi: Tune cache behavior
trace:
- Fix flyrecord alignment issue
xilinx:
- Move scriptaddr to DT as bootscr-address
- Pick script_offset_f/script_size_f from DT as bootscr-flash-offset/size
- Do not generate distro boot variables if disabled
versal:
- Extend memory ranges to cover HBM
- Enable TPM, sha1sum and KASLRSEED
- Fix distroboot prioritization in connection to available devices
- Clean mini targets bootcommand
- Fix clock driver
versal-net:
- Enable TPM, sha1sum and KASLRSEED
- Fix distroboot prioritization in connection to available devices
zynqmp;
- Allow AES to run from SPL
- Enable CMD_KASLRSEED
- Add proper dependencies for USB and remove ZYNQMP_USB
- Fix user si570 default frequency for zcu* boards
- Cover SOM rev2 revision
- Various DT changes
- Add firmware and pinctrl support for tristate configuration
(high impedance/output enable)
- Add output-enable pins to SOMs
- Fix distroboot prioritization in connection to available devices
- Read bootscript address/flash address from DT
- Fix pcap_prog address
When flash erase is called with size parameter, code is checking
if sectors are locked or not. But for checking, the whole device
length minus offset is used instead of actual size which should
be erased. That's why when only some sectors are locked it is
not possible to erase unlocked sectors.
The length is calculated as "length = max_chipsize - offset",
flash_is_unlocked() api is getting updated with length which is
incorrect. Fix this flash_is_unlocked() api by passing the size
parameter.
ZynqMP> sf erase 0 100000
len=0x8000000 which is flash size
size=0x100000
We need to update the size in the flash_is_unlocked() api and not
the length.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20230920025450.6281-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
When CONFIG_CMD_USB and CONFIG_USB are disabled, still some compilation
errors are seen as below.
In file included from include/configs/xilinx_zynqmp.h:173,
from include/config.h:3,
from include/common.h:16,
from env/common.c:10:
include/config_distro_bootcmd.h:302:9: error: expected '}' before 'BOOT_TARGET_DEVICES_references_USB_without_CONFIG_CMD_USB'
302 | BOOT_TARGET_DEVICES_references_USB_without_CONFIG_CMD_USB
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
include/config_distro_bootcmd.h:302:9: note: in definition of macro
'BOOTENV_DEV_NAME_USB'
302 | BOOT_TARGET_DEVICES_references_USB_without_CONFIG_CMD_USB
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
include/configs/xilinx_zynqmp.h:77:41: note: in expansion of macro
'BOOTENV_DEV_NAME'
77 | # define BOOT_TARGET_DEVICES_USB(func) func(USB, usb, 0)
func(USB, usb, 1)
| ^~~~
include/configs/xilinx_zynqmp.h:168:9: note: in expansion of macro
'BOOT_TARGET_DEVICES_USB'
168 | BOOT_TARGET_DEVICES_USB(func) \
| ^~~~~~~~~~~~~~~~~~~~~~~
include/config_distro_bootcmd.h:454:25: note: in expansion of macro
'BOOT_TARGET_DEVICES'
454 | "boot_targets=" BOOT_TARGET_DEVICES(BOOTENV_DEV_NAME) "\0"
| ^~~~~~~~~~~~~~~~~~~
include/config_distro_bootcmd.h:474:9: note: in expansion of macro
'BOOTENV_BOOT_TARGETS'
474 | BOOTENV_BOOT_TARGETS \
| ^~~~~~~~~~~~~~~~~~~~
include/configs/xilinx_zynqmp.h:179:9: note: in expansion of macro
'BOOTENV'
179 | BOOTENV
| ^~~~~~~
include/env_default.h:120:9: note: in expansion of macro
'CFG_EXTRA_ENV_SETTINGS'
120 | CFG_EXTRA_ENV_SETTINGS
| ^~~~~~~~~~~~~~~~~~~~~~
In file included from env/common.c:32:
include/env_default.h:27:36: note: to match this '{'
27 | const char default_environment[] = {
| ^
scripts/Makefile.build:256: recipe for target 'env/common.o' failed
make[1]: *** [env/common.o] Error 1
Makefile:1853: recipe for target 'env' failed
make: *** [env] Error 2
make: *** Waiting for unfinished jobs....
Add CONFIG_USB_STORAGE as dependency for USB related macro's such as
BOOT_TARGET_DEVICES_USB() and DFU_DEFAULT_POLL_TIMEOUT and
CONFIG_THOR_RESET_OFF.
Remove CONFIG_ZYNQMP_USB from Kconfig and also from defconfig since it
is not used anywhere else.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20230904031528.11817-3-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
When CONFIG_CMD_USB and CONFIG_USB are disabled some compilation errors are seen as below.
cmd/thordown.o: in function `usb_gadget_initialize':
include/linux/usb/gadget.h:981: undefined reference to `board_usb_init'
cmd/thordown.o: in function `do_thor_down':
cmd/thordown.c:68: undefined reference to `g_dnl_unregister'
cmd/thordown.o: in function `usb_gadget_release':
include/linux/usb/gadget.h:986: undefined reference to `board_usb_cleanup'
cmd/thordown.o: in function `do_thor_down':
cmd/thordown.c:41: undefined reference to `g_dnl_register'
cmd/thordown.c:48: undefined reference to `thor_init'
cmd/thordown.c:56: undefined reference to `thor_handle'
gnu/aarch64/lin/aarch64-linux/bin/aarch64-linux-gnu-ld.bfd: line 4: 8485
Segmentation fault (core dumped) $CC --sysroot=$LIBC
--no-warn-rwx-segment "$@"
Makefile:1779: recipe for target 'u-boot' failed
make: *** [u-boot] Error 139
make: *** Deleting file 'u-boot'
Add dependency of USB_GADGET_DOWNLOAD for CONFIG_CMD_THOR_DOWNLOAD to fix the errors.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Link: https://lore.kernel.org/r/20230904031528.11817-2-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
For reference clocks, PM_CLK_GET_PARENT call is not allowed.
PM_CLK_GET_PARENT only allowed for MUX clocks. Rename the
versal_clock_ref() with versal_clock_get_ref_rate() for better
readability. Fix the versal_clock_get_ref_rate function by
passing the parent_id, and check whether the parent_id
belongs to ref_clk or pl_alt_ref_clk.
Also adding the function versal_clock_get_fixed_factor_rate()
if the clk_id belongs to the fixed factor clock.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20230912033055.2549-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
SOC can boot in the device which is not accessible from APU and running
this is detected as error which ends up in stopping boot process.
Boot mode detection and logic around is present to setup priority on boot
devices that SOC boot device is likely also used for booting OS.
Change logic to detect this case with showing message about it but don't fail
in boot process and don't prioritize boot device in this case.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20230904032035.11926-4-venkatesh.abbarapu@amd.com
SOC can boot in the device which is not accessible from APU and running
this is detected as error which ends up in stopping boot process.
Boot mode detection and logic around is present to setup priority on boot
devices that SOC boot device is likely also used for booting OS.
Change logic to detect this case with showing message about it but don't fail
in boot process and don't prioritize boot device in this case.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20230904032035.11926-3-venkatesh.abbarapu@amd.com
SOC can boot in the device which is not accessible from APU and running
this is detected as error which ends up in stopping boot process.
Boot mode detection and logic around is present to setup priority
on boot devices that SOC boot device is likely also used for booting OS.
Change logic to detect this case with showing message about it but don't
fail in boot process and don't prioritize boot device in this case.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20230904032035.11926-2-venkatesh.abbarapu@amd.com
Location of bootscript in flash can be specified via /options/u-boot DT
node by using bootscr-flash-offset and bootscr-flash-size properties.
Values should be saved to script_offset_f and script_size_f variables.
Variables are described in doc/develop/bootstd.rst as:
script_offset_f
SPI flash offset from which to load the U-Boot script, e.g. 0xffe000
script_size_f
Size of the script to load, e.g. 0x2000
Both of them are used by sf_get_bootflow() in drivers/mtd/spi/sf_bootdev.c
to identify bootscript location inside flash.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/60a84405f3fefabb8b48a4e1ce84431483a729f3.1693465465.git.michal.simek@amd.com
ofnode_read_bootscript_flash() reads bootscript address from
/options/u-boot DT node. bootscr-flash-offset and bootscr-flash-size
properties are read and values are filled. When bootscr-flash-size is not
defined, bootscr-flash-offset property is unusable that's why cleaned.
Both of these properties should be defined to function properly.
Also add test to cover this new function.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/08a3e6c09cce13287c69ad370e409e7f1766b406.1693465465.git.michal.simek@amd.com
Now that the zynqmp pinctrl driver supports the tri-state registers, make
sure that the pins requiring output-enable are configured appropriately for
SOMs.
Without it, all tristate setting for MIOs, which are not related to SOM
itself, are using default configuration which is not correct setting.
It means SDs, USBs, ethernet, etc. are not working properly.
In past it was fixed through calling tristate configuration via bootcmd:
usb_init=mw 0xFF180208 2020
kv260_gem3=mw 0xFF18020C 0xFC0 && gpio toggle gpio@ff0a000038 && \
gpio toggle gpio@ff0a000038
Signed-off-by: Neal Frager <neal.frager@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/7ecd98b2a302c5c6628e0234482f23c38e721fd6.1693492064.git.michal.simek@amd.com
The bootscript is expected at a default address specific to each
platform.
When high speed memory like Programmable Logic Double Data Rate RAM
(PL DDR RAM) or Higher Bandwidth Memory RAM (HBM) is used the boot.scr
may be loaded at a different offset. The offset needs to be set through
setenv. Due to the default values in some cases the boot.scr is falling
in between the kernel partition.
The bootscript address or the bootscript offset is fetched directly from
the DT and updated in the environment making it easier for automated
flows.
Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/fac7020b31e1f150b021d666f0d588579ea671ad.1693465140.git.michal.simek@amd.com
Kernel Address Space Layout Randomization (KASLR) is a hardening
feature that aims to make it more difficult to take advantage
of known exploits in the kernel, by placing kernel data
structures at a random address at each boot.The bootloader
supports randomizing the virtual address at which the kernel image
is loaded. The bootloader must provide entropy by passing a random
u64 value in the /chosen/kaslr-seed device tree node.
When we run "kaslrseed" command from U-Boot, the bootloader will
genarate the kaslr-seed and update the /chosen/kaslr-seed DT property.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20230831031658.2203-4-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Kernel Address Space Layout Randomization (KASLR) is a hardening
feature that aims to make it more difficult to take advantage
of known exploits in the kernel, by placing kernel data structures
at a random address at each boot.The bootloader supports randomizing
the virtual address at which the kernel image is loaded.
The bootloader must provide entropy by passing a random u64 value
in the /chosen/kaslr-seed device tree node.
When we run "kaslrseed" command from U-Boot, the bootloader will
genarate the kaslr-seed and update the /chosen/kaslr-seed DT property.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20230831032612.2729-4-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
This fixes below build error when CC_OPTIMIZE_FOR_DEBUG is enabled and
CONFIG_FPGA or CONFIG_SPL_FPGA are not enabled.
When CC_OPTIMIZE_FOR_DEBUG is enabled, unused code will not be optimized
out. Hence, fpga_load function must have a dummy implementation to avoid
the build error.
../common/spl/spl_fit.c:591: undefined reference to `fpga_load'
collect2: error: ld returned 1 exit status
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Link: https://lore.kernel.org/r/20230831075247.137501-1-chanho61.park@samsung.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
All si570 mgt chips have factory default 156.25MHz but DT changed it to
148.5MHz. After tracking it is pretty much c&p fault taken from Zynq
zc702/zc706 boards where 148.5MHz was setup as default because it was
requirement for AD7511 chip available on these boards.
ZynqMP board don't contain this chip that's why factory default frequency
can be used.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/c052ddf39e392e97f87f1c57ea06f3508733c672.1692947486.git.michal.simek@amd.com
Kernel Address Space Layout Randomization (KASLR) is a hardening
feature that aims to make it more difficult to take advantage
of known exploits in the kernel, by placing kernel data structures
at a random address at each boot.The bootloader supports randomizing
the virtual address at which the kernel image is loaded.
The bootloader must provide entropy by passing a random u64 value
in the /chosen/kaslr-seed device tree node.
When we run "kaslrseed" command from U-Boot, the bootloader will
genarate the kaslr-seed and update the /chosen/kaslr-seed DT property.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20230824032712.13399-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
HBM stands for high bandwidth memory and is a type of memory interface used
in 3D-stacked DRAM (dynamic random access memory) in some AMD GPUs (aka
graphics cards), as well as the server, high-performance computing (HPC)
and networking and client space. High Bandwidth Memory(HBM) has total 16
channels, one channel is divided into two pseudo channels which makes its
32 banks each with some amount of memory.
And then we have DDR_LOW PS low, DDR_HIGH0 PS high, DDR_HIGH1 PS very high
and pretty much there should be also place for PL DDR. So maximum number of
memory banks will be 36, updating the CONFIG_NR_DRAM_BANKS to 36.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/ed9eaf5c20501ee691d7d28a173511cd9a87f161.1690958095.git.michal.simek@amd.com
The StarFive VisionFive 2 board cannot load spl/u-boot-spl.bin but needs a
prefixed header. We have referring to a vendor tool (spl_tool) for this
task. 'mkimage -T sfspl' can generate the prefixed file.
Use binman to invoke mkimage for the generation of file
spl/u-boot-spl.bin.normal.out.
Update the documentation.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Tested-by: Milan P. Stanić <mps@arvanta.net>
The StarFive JH7110 base boards require a header to be prefixed to the SPL
binary image. This has previously done with a vendor tool 'spl_tool'
published under a GPL-2-or-later license. Integrate this capability into
mkimage.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Tested-by: Chanho Park <chanho61.park@samsung.com>
Tested-by: Milan P. Stanić <mps@arvanta.net>
boot from SDIO3.0 (mmc sdcard) first if it is plugged.
If mmc is not plugged try to boot from emmc if it is plugged.
If emmc is not plugged then try to boot from nvme.
Signed-off-by: Milan P. Stanić <mps@arvanta.net>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Multiple revisions of the StarFive VisionFive 2 board exist. They can be
identified by reading their EEPROM.
Linux uses two differently named device-tree files. To load the correct
device-tree we need to set $fdtfile to the device-tree file name that
matches the board revision.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This is not needed, so drop it. Also use a capital 'O' for the option,
while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
We need CONFIG_OF_LIBFDT to be able to do fdt fixups, so add that
condition.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Standard boot has been in place for a while now. Quite a few problems
have been found and fixed. It seems like a good time to mark the
script-based approach as deprecated and encourage people to use standard
boot.
Update the DISTRO_DEFAULTS Kconfig to encourage people to move to
standard boot, which is able to boot Linux distributions automatically.
Add a short migration guide to make this easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These don't relate to booting. Move them out of there and into the same
place as the other related settings.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This option already depends on FIT, so put it under the same umbrella, so
that it appears in the FIT menu.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
All boards which actually define this address enable SPL_LOAD_FIT, or at
least just rely on the default value of 0. So drop the dependency.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This CONFIG is used but is not given a value by some boards. Use
a default value of 0 explicitly, rather than relying on the 0 value
provided by CONFIG_SPL_LOAD_FIT_ADDRESS
This will allow us to make SPL_LOAD_FIT_ADDRESS depend on SPL_LOAD_FIT
as it should.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This is a major feature with a lot of options. Give it its own menu to
tidy up the 'make menuconfig' display. Drop the 'depends on FIT' pieces
which are now unnecessary, since they are now bracketed by an 'if FIT'.
Leave CONFIG_TIMESTAMP out since it affects legacy images too.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Phrases like 'Enable support for' are pointless since this is an option
which enables things. Drop that part so it is easier to follow.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move more options relating to fixing up a device tree into the new
devicetree-fixup menu.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This relates to booting, so move it there. Create a new Kconfig menu for
things related to devicetree fixup.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This relates to booting since it fixes up the devicetree for the OS. Move
it into the boot/ directory.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Rename Unit tests to Testing, since it is a stretch to describe some of
the tests as unit tests. Move POST there as well, so it doesn't show up
by itself in the top-level menu.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These appear prominently in the main menu at present. Move them to the
video Kconfig where they belong.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This relates to graphics which is only active when CONFIG_VIDEO is
enabled. Move it into that directory.
For most boards there is no harm in compiling it always, since it if not
used it will be dropped by the linker. But for the EFI app this is not
the case, so retain use of the BMP Kconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This is perhaps not a commonly used feature so should not have its own
option in the main menu. Move it under general setup.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These should not be part of the 'system tables' menu. Move them outside
on their own.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: 7d0f3fbb93 ("lib: rational: copy the rational fraction lib...")
Reviewed-by: Tom Rini <trini@konsulko.com>
The constants to define the idle state of SERDES MUX were defined in
bindings header. They are used only in DTS and driver uses the dt property
to set the idle state making it unsuitable for bindings.
The constants are moved to header next to DTS ("arch/arm/boot/dts/")
and all the references to bindings header are removed.
So add a warning to mark this bindings header as deprecated.
We could probably drop this header, but let us wait for kernel to
cleanup.
Signed-off-by: Nishanth Menon <nm@ti.com>
The DTS uses constants for SERDES MUX idle state values which were earlier
provided as bindings header. But they are unsuitable for bindings.
So move these constants in a header next to DTS.
NOTE: sync with v6.6-rc1 will bring in this change naturally.
Signed-off-by: Nishanth Menon <nm@ti.com>
Introduce the new serdes header from kernel v6.6-rc1
The DTS uses constants for SERDES MUX idle state values which were earlier
provided as bindings header. But they are unsuitable for bindings.
So move these constants in a header next to DTS.
Signed-off-by: Nishanth Menon <nm@ti.com>
The ti,j7200-vtm and ti,j721e-vtm compatibles are used for voltage
and thermal monitoring (VTM) by (drivers/thermal/k3_j72xx_bandgap.c)
in Linux, but the same hardware is used for adaptive voltage scaling
(AVS) in u-boot, This brings both drivers in line with the same
compatibles.
Since the j7200 uses the config as the j721e, the data is inherited
from j721e vs creating a duplicate
Signed-off-by: Neha Francis <n-francis@ti.com>
Signed-off-by: Reid Tonking <reidt@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Change the file name from ti.gz and ti.bmp to ti_logos_414x97_32bpp to
help user understand the resolution and identify the logo files when
placed in the boot partition and update the splashfile name with the
same in .env file.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
In 2cb43ef1c2 ("usb: ether: Fix error handling in usb_ether_init") the error
handling of usb_ether_init() was changed. Not a single other call site of this
function checks its return value, therefore follow suit in the am33xx code.
Do not cause the boot to halt if the usb gadget ethernet initialization fails:
initcall sequence 9ffdbd84 failed at call 808024b9 (err=-19)
### ERROR ### Please RESET the board ###
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Reviewed-by: Michal Suchánek <msuchanek@suse.de>
The usb_gadget_handle_interrupts() is no longer used anywhere,
replace the remaining uses with dm_usb_gadget_handle_interrupts()
which takes udevice as a parameter.
Some of the UDC drivers currently ignore the index parameter altogether,
those also ignore the udevice and have to be reworked. Other like the
dwc3_uboot_handle_interrupt() had to be switched from index to udevice
look up to avoid breakage.
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # on khadas vim3
Signed-off-by: Marek Vasut <marex@denx.de>
Remove legacy functions limited by the dev_array array,
those are no longer used anywhere, all the code uses
plain udevice based access now.
The usb_gadget_handle_interrupts() is doing udevice look up
until all call sites use dm_usb_gadget_handle_interrupts().
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Convert to plain udevice interaction with UDC controller
device, avoid the use of UDC uclass dev_array .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Convert to plain udevice interaction with UDC controller
device, avoid the use of UDC uclass dev_array .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Convert to plain udevice interaction with UDC controller
device, avoid the use of UDC uclass dev_array .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Convert to plain udevice interaction with UDC controller
device, avoid the use of UDC uclass dev_array .
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Marek Vasut <marex@denx.de>
In case anything errors out during the SDP transfer, detach
the controller instead of bailing out right away. This way,
the controller can be reattached on next attempt.
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Convert to plain udevice interaction with UDC controller
device, avoid the use of UDC uclass dev_array .
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Marek Vasut <marex@denx.de>
In case anything errors out during the DFU registration, detach
the controller instead of bailing out right away. This way, the
controller can be reattached on next attempt.
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Convert to plain udevice interaction with UDC controller
device, avoid the use of UDC uclass dev_array .
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # on khadas vim3
Signed-off-by: Marek Vasut <marex@denx.de>
Move the variable declaration around to improve code readability.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Move the variable declaration around to improve code readability.
No functional change.
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Convert to plain udevice interaction with UDC controller
device, avoid the use of UDC uclass dev_array .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Convert to plain udevice interaction with UDC controller
device, avoid the use of UDC uclass dev_array .
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # on khadas vim3
Signed-off-by: Marek Vasut <marex@denx.de>
Remove local usb_gadget_register_driver()/usb_gadget_unregister_driver()
implementation which is implemented in udc-core.c instead if DM_USB_GADGET
is enabled. Add no-op dm_usb_gadget_handle_interrupts() implementation.
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Pull the functionality of UDC uclass that operates on plain udevice
and does not use this dev_array array into separate functions and
expose those functions, so that as much code as possible can be
switched over to these functions and the dev_array can be dropped.
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Marek Vasut <marex@denx.de>
To quote the author:
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
This is a follow up on way over decade old commit
2e5167ccad ("Replace CONFIG_RELOC_FIXUP_WORKS by CONFIG_NEEDS_MANUAL_RELOC")
"
By now, the majority of architectures have working relocation
support, so the few remaining architectures have become exceptions.
To make this more obvious, we make working relocation now the default
case, and flag the remaining cases with CONFIG_NEEDS_MANUAL_RELOC.
"
It took a bit longer than expected, but now we can really sunset
CONFIG_NEEDS_MANUAL_RELOC.
Make it so.
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The last user of the NEEDS_MANUAL_RELOC has been removed in commit
26af162ac8 ("arch: m68k: Implement relocation")
Remove now unused NEEDS_MANUAL_RELOC code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Refactor generic_{setup,shutdown}_phy() to reduce complexity and
indentation. This have no intended functional change.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Restore the old behavior of ehci_setup_phy() and ohci_setup_phy() to
return success when generic_phy_get_by_index() return -ENOENT.
Fixes: 84e561407a ("phy: Add generic_{setup,shutdown}_phy() helpers")
Fixes: 10005004db ("usb: ohci: Make usage of generic_{setup,shutdown}_phy() helpers")
Fixes: 083f8aa978 ("usb: ehci: Make usage of generic_{setup,shutdown}_phy() helpers")
Fixes: 75341e9c16 ("usb: ehci: Remove unused ehci_{setup,shutdown}_phy() helpers")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
generic_phy_exit() typically return 0 for a struct phy that has been
initialized with a generic_phy_init() call.
generic_setup_phy() returns the value from a generic_phy_exit() call
when generic_phy_power_on() fails. This hides the failed state of the
power_on ops from the caller of generic_setup_phy().
Fix this by ignoring the return value of the generic_phy_exit() call and
return the value from the generic_phy_power_on() call.
Fixes: 84e561407a ("phy: Add generic_{setup,shutdown}_phy() helpers")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
The documentation for struct phy state that "The content of the
structure is managed solely by the PHY API and PHY drivers".
Change to use the generic_phy_valid() helper to check if phy is valid.
Fixes: b7d8d40346 ("video: rockchip: dw_mipi_dsi: Fix external phy existence check")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The documentation for struct phy state that "The content of the
structure is managed solely by the PHY API and PHY drivers".
Change to use the generic_phy_valid() helper to check if phy is valid.
Fixes: 10c50b1fac ("net: zynq: Add support for PHY configuration in SGMII mode")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
The documentation for struct phy state that "The content of the
structure is managed solely by the PHY API and PHY drivers".
Change to use the generic_phy_valid() helper to check if phy is valid.
Fixes: f6f5451d46 ("scsi: ceva: Enable PHY and reset support")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
The documentation for struct phy state that "The content of the
structure is managed solely by the PHY API and PHY drivers".
Change to use the generic_phy_valid() helper to check if phy is valid.
Also remove setting phy->dev to NULL now that generic_phy_get_by_name()
properly initialize phy->dev to NULL.
Fixes: 142d50fbce ("usb: dwc3: Add support for usb3-phy PHY configuration")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Generic phy helpers typically use generic_phy_valid() to determine if
the helper should perform its function on a passed struct phy.
generic_phy_valid() treat any struct phy having phy->dev set as valid.
With generic_phy_get_by_index_nodev() setting phy->dev to a valid struct
udevice early, there can be situations where the struct phy is returned
as valid when initialization in fact failed and returned an error.
Fix this by setting phy->dev back to NULL when any of the calls to
of_xlate ops, device_get_supply_regulator or phy_alloc_counts fail. Also
extend the dm_test_phy_base test with a test where of_xlate ops fail.
Fixes: 72e5016f87 ("drivers: phy: add generic PHY framework")
Fixes: b9688df3cb ("drivers: phy: Set phy->dev to NULL when generic_phy_get_by_index() fails")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
generic_phy_get_by_name() does not initialize phy->dev to NULL before
returning when dev_read_stringlist_search() fails. This can lead to an
uninitialized or reused struct phy erroneously be report as valid by
generic_phy_valid().
Fix this issue by initializing phy->dev to NULL, also extend the
dm_test_phy_base test with calls to generic_phy_valid().
Fixes: b9688df3cb ("drivers: phy: Set phy->dev to NULL when generic_phy_get_by_index() fails")
Fixes: 868d58f69c ("usb: dwc3: Fix non-usb3 configurations")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
It's Broadcom PHY simply described as single-port
RGMII 10/100/1000BASE-T PHY. It requires disabling
delay skew and GTXCLK bits.
BCM54210E support ported from Linux kernel commit
0fc9ae1076697 ("net: phy: broadcom: add support for BCM54210E")
AUX/SHD/bcm54xx_config_clock_delay update ported from Linux 6.5-rc4 commit
28e219aea0b9e ("net: phy: broadcom: drop brcm_phy_setbits() and use phy_set_bits() instead")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Rafał Miłecki <rafal@milecki.pl>
The YT8511 ethernet PHYs can be found on e.g. the SOQuartz or
the Quartz64. Add rudimentary support for them.
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Bring in two series to improve GPT support. For the first series from
Joshua:
Adds several improvements and additions to the gpt command processing,
specifically (although not exclusively) for the purpose of supporting
"ping-pong" booting when doing A/B boot partitions with u-boot itself.
In this mechanism, u-boot must boot up, and then check if the correct
boot partition is active, and if not switch the GPT partition table to
the other boot partition and reboot to activate the other u-boot.
In order to facilitate this, the gpt command needs to be better at
preserving entry attributes when manipulating the partition table. It
also learns two new commands, one which can swap the order of partitions
in the table, and another that lets it change which partitions have the
bootable flag.
For the second series from Heinrich:
To partition a block device the partition type GUIDs are needed but
'gpt read' does not provide these. Add the missing parts.
There is some overlap in these two series but I believe I have merged
things correctly.
To partition a block device the partition type GUIDs are needed but
'gpt read' does not provide these. Add the missing parts.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
* Avoid incrementing by moving comma into strlen("uuid_disk=,") and
considering NUL byte.
* Appending a UUID only adds UUID_STR_LEN bytes.
Don't count the terminating NUL.
* The length of the hexadecimal representation of lba_int is
2 * sizeof(lba_int).
* We don't use a 'MiB' postfix but a '0x' prefix.
* The uuid field is only needed if configured.
Fixes: 2fcaa413b3 ("gpt: harden set_gpt_info() against non NULL-terminated strings")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
disk_partition_uuid() and disk_partition_set_uuid() were introduced to let
us avoid the usage of #ifdef when dealing with the field uuid of
struct disk_partition.
In allocate_disk_part() commit c5f1d005f5 ("part: Add accessors for
struct disk_partition uuid") missed to use the setter.
print_gpt_info() and create_gpt_partitions_list() are further functions
where we should use the getter.
Fixes: c5f1d005f5 ("part: Add accessors for struct disk_partition uuid")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Rename disk_partition_type_uuid to disk_partition_type_guid.
Provide function descriptions for the getter and setter.
Fixes: bcd645428c ("part: Add accessors for struct disk_partition type_uuid")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Adds a command called "gpt transpose" which will swap the order two
partition table entries in the GPT partition table (but leaves them
pointing to the same locations on disk).
This can be useful for swapping bootloaders in systems that use an A/B
partitioning scheme where the bootrom is hard coded to look for the
bootloader in a specific index in the GPT partition table.
Signed-off-by: Joshua Watt <JPEWhacker@gmail.com>
Sets the bootable flag when constructing the partition string from the
current partition configuration. This ensures that when the partitions
are written back (for example, when renaming a partition), the flag is
preserved.
Signed-off-by: Joshua Watt <JPEWhacker@gmail.com>
If CONFIG_PARTITION_TYPE_GUID is enabled, the type GUID will be
preserved when writing out the partition string. It was already
respected when writing out partitions; this ensures that if you capture
the current partition layout and write it back (such as when renaming),
the type GUIDs are preserved.
Signed-off-by: Joshua Watt <JPEWhacker@gmail.com>
Adds a command that can be used to modify the GPT partition table to
indicate which partitions should have the bootable flag set
Signed-off-by: Joshua Watt <JPEWhacker@gmail.com>
Adds an additional variable called gpt_partition_bootable that indicates
if the given partition is bootable or not.
Signed-off-by: Joshua Watt <JPEWhacker@gmail.com>
The "#include <common.h>" is being phased out in favor of more fine
grained header management, i.e. ideally include a subset of headers
that are really needed. Remove it from this driver.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable UFS controller driver and matching UFS and SCSI commands. The
former is used to initialize the device, the later is used to perform
low level access to the SCSI interface of the UFS device.
Enable R8A779F0 S4 Spider specific dependencies, the PCA953x driver
and GPIO clock gate driver. This setup is used to toggle 38.4 MHz
clock for the UFS controller.
Enable support for 48bit LBA in block layer to address disks larger
than 512*2^32 ~= 144 PiB. Enable use of 64bit LBA variables in the
rest of U-Boot, instead of the default 32bit ones.
Increase FAT cluster size to 128k as that is what is used by the
filesystem that is populated on the UFS device.
Use 'ufs init && scsi scan' to start the UFS device from U-Boot prompt.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add support for Renesas R-Car UFS controller which needs vendor-specific
initialization.
Ported from Linux kernel as of commit
c2ab666072bc ("scsi: ufs: Explicitly include correct DT includes")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add driver which implements GPIO-controlled clock. The GPIO is used
as a gate to enable/disable the clock. This matches linux clk-gpio.c
driver, however this does not implement the GPIO mux part, which in
U-Boot DM would be better fit in separate driver.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
To have the WDIOF_CARDRESET support for the TI AM65x platform watchdog,
this patch reserves some memories, which indicate if the current boot due
to a watchdog reset.
Signed-off-by: Li Hua Qian <huaqian.li@siemens.com>
Drop unused macro. This was copied straight from the AM62x EVM but while
meant for a second region of DDR this is not even needed for the AM62x
EVM configurations and has meanwhile also been dropped there.
Note that on the Verdin AM62, we do auto-detect the amount of SDRAM.
While at it also update the comment noting that CFG_SYS_SDRAM_SIZE is
the maximum which is only used for such auto-detection.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Update the DDR settings to those generated using 0.10 version of Jacinto
7 DDRSS Register Configuration tool.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
BeagleBoard.org BeaglePlay is an easy to use, affordable open source
hardware single board computer based on the Texas Instruments AM625
SoC that allows you to create connected devices that work even at long
distances using IEEE 802.15.4g LR-WPAN and IEEE 802.3cg 10Base-T1L.
Expansion is provided over open standards based mikroBUS, Grove and
QWIIC headers among other interfaces.
This board family can be identified by the 24c32 eeprom:
[aa 55 33 ee 01 37 00 10 2e 00 42 45 41 47 4c 45 |.U3..7....BEAGLE|]
[50 4c 41 59 2d 41 30 2d 00 00 30 32 30 30 37 38 |PLAY-A0-..020078|]
https://beagleplay.org/https://git.beagleboard.org/beagleplay/beagleplay
baseline of base device tree is v6.5-rc1.
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Co-developed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
While boot partition support with EMMC boot is useful, it is
constrained by the size of boot hardware partition itself.
In the case of K3 devices, tispl images can contain OP-TEE images that
can substantially vary in size and the u-boot image itself can vary over
time as we enable various features.
So use the CSD information in the case of EMMC_BOOT configuration being
enabled to pick boot partition or UDA FS mode operation to pick.
If EMMC_BOOT is disabled, then depend on filesystem configuration to
pick data from UDA.
While at this, drop the extraneous whitespace.
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
The erratum is called locally, make it static, drop the #ifdeffery since
it will only be called in R5 build and mark it potentially unused to
stop compiler screaming at us.
While at this, drop the redundant return for a void function.
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
ti_mmc bootmethod uses a findfdt routine that is expected to be
implemented by all platforms.
Define a default findfdt based on configured DEFAULT_DEVICE_TREE option
for u-boot. This saves duplication across multiple boards and handles
architecture folder location changes centrally.
TI ARMV7 platforms will need to override default_device_tree_subarch
in the env file to point to the appropriate platform. Note: default
"omap" is used to cater to "most common" default.
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Add explicit boot_targets to indicate the specific boot sequence to
follow.
NOTE: The non-standard ti_mmc emulates what is done for distro_boot.
With bootstd, this will eventually need to be replaced by equivalent
class.
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Wrap the distro_boot options with CONFIG_DISTRO_DEFAULTS.
This is an intermediate step for us to switch over to
CONFIG_BOOTSTD_DEFAULTS and drop this section in follow on patches.
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Drop unused macro. This was meant for a second region of DDR which we
do not need for AM62x evm configurations.
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
If mmc dev reports that the device is not present, there is no point in
proceeding further to attempt to load the files.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
verdin am62 SKUs comes in multiple memory configuration, check that
the detected memory is at least 512MB since we have some
reserved memory just before this threshold and therefore
the module cannot work with less memory.
Fixes: 7d1a10659f ("board: toradex: add verdin am62 support")
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Acked-by: Francesco Dolcini <francesco.dolcini@toradex.com>
- Merge in a number of changes for CI. The biggest ones of note are that
we now support sandbox64 in CI, and Azure has been reworked to
generally have more consistent overall runtime for the pipeline.
Now that sandbox64 can run and pass the regular test.py suite, add it
here as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently, most sandbox runs take a long time (due to running so many
tests) while QEMu based test.py runs are fairly short. Split the
pipeline here so that we get more consistent average run times.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Both to aide in debugging of any test.py issues as well as to make it
easier to split the current matrix in two, have a new job that creates
and publishes the current wrapper script we use for test.py jobs.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- We have added more TODO/etc comments since this task was created and
never focused on removing them.
- The output of sloccount isn't preserved or looked at, and if desired
should be in the release stats pages instead somehow.
- The results of cppcheck aren't investigated and require modeling work
to be useful to start with.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These jobs are to confirm specific build targets, on a Linux host. We
can safely combine these two build tests, with a make mrproper in
between.
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that we have 3600 minutes per build job, condense and rework things
such that our overall time largely doesn't change, but we can also
largely avoid having to re-tweak this job to avoid timeouts. Given that
we have 10 threads, we also move a few of the specific sandbox test
builds to a prior stage.
Note that while sandbox builds with address sanitization enabled (ASAN)
not all tests pass, so we limit ourselves to just checking that the
version test passes for now.
Link: https://learn.microsoft.com/en-us/azure/devops/pipelines/process/phases?view=azure-devops&tabs=yaml#timeouts
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use the following regex to make this test compatible with
both 32bit and 64bit systems. The trick is to use %0*lx
format string for the address prefix in the test.
"
s@\(ut_assert_nextline("\)0\+\([^:]\+\)\(:.*"\)\();\)@\1%0*lx\3, IS_ENABLED(CONFIG_PHYS_64BIT) ? 16 : 8, 0x\2UL\4
"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The current fdtdec_get_addr() takes into consideration #address-cells
and #size-cells for "ping-expect" property which is clearly neither.
Use fdtdec_get_int() instead and return negative one in case the
property is not in DT or the platform under test is not DT based,
i.e. mimic the current fdtdec_get_addr() behavior.
This fixes ut dm dm_test_bus_children test.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Align the sandbox64 defconfig with sandbox defconfig. Enable missing
legacy image format support. This fixes ut_bootstd_bootflow_cmd_menu
test.
Suggested-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Clean the function up a bit further. Return immediately on match
and return ARRAY_SIZE() - 1 on failure. Add proper comment in that
case.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
With having both an EVENT_SPY_SIMPLE setup for both riscv_cpu_probe and
riscv_cpu_setup we do not need the latter function to call the former
function as it will already have been done in time.
Fixes: 1c55d62fb9 ("riscv: cpu: make riscv_cpu_probe to EVT_DM_POST_INIT_R callback")
Tested-by: Milan P. Stanić <mps@arvanta.net>
Signed-off-by: Tom Rini <trini@konsulko.com>
Implement relocation for M68K. Perform all the updates in start.S
relocate_code in assemby, since it is a simple matter of traversing
the dynsym table and adding relocation offset - MONITOR_BASE to all
the items in that table. The necessity to deal with MONITOR_BASE is
a specific of M68K, where the ELF entry point is at offset 0x400,
which is the MONITOR_BASE, while TEXT_BASE is at offset 0 .
This also removes the one last user of NEEDS_MANUAL_RELOC, so that
could be finally cleaned up .
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add M68K ELF32 support into this tool, so it can patch static rela
into M68K u-boot-nodtb.bin . This is the first step toward M68K
relocation support, and in turn, removal of NEEDS_MANUAL_RELOC
from the codebase altogether.
Tested-by: Michal Simek <michal.simek@amd.com> # microblaze, arm64
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The symtab contains data in target endianness, convert the data to
native endianness before doing any operations and on them, and back
to target endianness before updating the bin file.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Tested-by: Michal Simek <michal.simek@amd.com> # microblaze, arm64
Reviewed-by: Angelo Dureghello <angelo@kernel-space.org>
EHCI is usually used with companion controller (like OHCI) as companion
controller. This information on the companion is missing currently in
companion drivers.
So, if the usb-uclass isn't aware, it may scan busses in any order: OHCI
first, then EHCI.
This is seen on STM32MP1 where DT probing makes the probe order to occur
by increasing address (OHCI address < EHCI address).
When a low speed or full-speed device is plugged in, it's not detected as
EHCI should first detect it, and give ownership (handover) to OHCI.
Current situation on STM32MP1 (with a low speed device plugged-in)
STM32MP> usb start
starting USB...
Bus usb@5800c000: USB OHCI 1.0
Bus usb@5800d000: USB EHCI 1.00
scanning bus usb@5800c000 for devices... 1 USB Device(s) found
scanning bus usb@5800d000 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
The "companion" property in the device tree allow to retrieve companion
controller information, from the EHCI node. This allow marking the
companion driver as such.
With this patch (same low speed device plugged in):
STM32MP> usb start
starting USB...
Bus usb@5800c000: USB OHCI 1.0
Bus usb@5800d000: USB EHCI 1.00
scanning bus usb@5800d000 for devices... 1 USB Device(s) found
scanning bus usb@5800c000 for devices... 2 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
STM32MP> usb tree
USB device tree:
1 Hub (12 Mb/s, 0mA)
| U-Boot Root Hub
|
+-2 Human Interface (1.5 Mb/s, 100mA)
HP HP USB 1000dpi Laser Mouse
1 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller
This also optimize bus scan when a High speed device is plugged in, as
the usb-uclass skips OHCI in this case:
STM32MP> usb reset
resetting USB...
Bus usb@5800c000: USB OHCI 1.0
Bus usb@5800d000: USB EHCI 1.00
scanning bus usb@5800d000 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
STM32MP> usb tree
USB device tree:
1 Hub (480 Mb/s, 0mA)
| u-boot EHCI Host Controller
|
+-2 Mass Storage (480 Mb/s, 200mA)
SanDisk Cruzer Blade 03003432021922011407
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
After the merge of v2023.10-rc4 to next include/event.h needs to be
fully documented in order for documentation builds to complete. Rewords
two of the event_t descriptions to be docbook style and better match the
rest of this enum. Fix two typos (flag->flags) in other comments.
Signed-off-by: Tom Rini <trini@konsulko.com>
To quote the author:
This series replaces some more of the init hooks in board_f.c and
board_r.c with events. Notably it converts last_state_init() over.
It also provides a 'simple' event spy, which takes no arguments. It
turns out that this is quite a common case, so it is worth optimising
for this, to reduce code size, before events become too commonly used.
Finally, it introduces a way of emitting an event in an initcall,
instead of calling a function. This is likely to be used at least as
often as the functions, as we convert more of these initcalls.
As part of this, the initcall code is brought back into a C file. Somehow
the compiler has changed or something else, so that this does not confer
any benefits now.
For boards with EVENT enabled, this unfortunately results in small
growth, e.g. for firefly:
aarch64: (for 1/1 boards) all +114.0 data +16.0 rodata +22.0 text +76.0
arm: (for 1/1 boards) all +82.0 rodata +18.0 text +64.0
For boards without EVENT enabled the growth is smaller, e.g. nokia_rx51:
arm: (for 1/1 boards) all +32.0 data +8.0 rodata -8.0 text +32.0
I cannot find a good way to avoid the latter, other than macro magic
with an embedded comma (to completely remove an event entry), which
seems nasty.
Add a new event which handles this function. Convert existing use of
the function to use the new event instead.
Make sure that EVENT is enabled by affected boards, by selecting it from
the LAST_STAGE_INIT option. For x86, enable it by default since all boards
need it.
For controlcenterdc, inline the get_tpm() function and make sure the event
is not built in SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use the misc_init_f event instead, which is designed for this purpose.
All boards with CONFIG_VID already enable CONFIG_EVENT.
Signed-off-by: Simon Glass <sjg@chromium.org>
Convert this to use events instead of calling a function directly in the
init sequence.
Rename it to arch_fsp_init_f() to distinguish it from the one that happens
after relocation.
For FSPv2 nothing needs to be done here, so drop the empty function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that we have two types of spy, mention this in the documentation. Put
the simple spy first, since it seems to be the common case.
Signed-off-by: Simon Glass <sjg@chromium.org>
The new name makes it clearer that this is for a full spy, with access to
the context and the event data.
Signed-off-by: Simon Glass <sjg@chromium.org>
Very few of the existing event-spy records use the arguments they are
passed. Update them to use a simple spy instead, to simplify the code.
Where an adaptor function is currently used, remove it where possible.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move the manual-relocation code to the initcall file. Make sure to avoid
manually relocating event types. Only true function pointers should be
relocated.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the initcall list consists of a list of function pointers. Over
time the initcall lists will likely change to mostly emitting events,
since most of the calls are board- or arch-specific.
As a first step, allow an initcall to be an event type instead of a
function pointer. Add the required macro and update initcall_run_list() to
emit an event in that case, or ignore it if events are not enabled.
The bottom 8 bits of the function pointer are used to hold the event type,
with the rest being all ones. This should avoid any collision, since
initcalls should not be above 0xffffff00 in memory.
Convert misc_init_f over to use this mechanism.
Add comments to the initcall header file while we are here. Also fix up
the trace test to handle the change.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move the failure message outside the loop, so it is easier to follow the
code. Avoid swallowing the error code - just pass it along.
Drop the initcall-list address from the output. This is confusing since
we show two addresses. Really it is only the function address which is
useful, since it can be looked up in the map, e.g. with:
grep -A1 -B1 serial_init u-boot.map
Signed-off-by: Simon Glass <sjg@chromium.org>
Use a variable to hold the function, so we don't need to repeat the
pointer access each time. Rename the init pointer to 'ptr' since we only
refer to it in the for() statement now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Somehow I do not see any inlining with initcalls now. I was sure I saw
it when this commit went in, but now it seems to make things worse.
This reverts commit 47870afab9.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current event spy is always passed the event context and the event.
The context is always NULL for a static spy. The event is not often used.
Introduce a 'simple' spy which takes no arguments. This allows us to drop
the adaptation code that many of these spy records use.
Update the event script to find these in the image.
Signed-off-by: Simon Glass <sjg@chromium.org>
- pcie-bcmstb improvements, nvmxip improvements, fix a corner case in
the serial uclass, send error messages to stderr in host tools, fwu
library CI state fixup, turn some setexpr diagnostic messages to debug
Neither successful match nor lack thereof should be considered an
extraordinary situation. Thus, neither require printing a message.
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The sandbox_set_enable_memio() should only ever be set during
sandbox testing, not within driver itself, move it back to test/ .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Cast the address such that it can be printed without warnings
on both 32bit and 64bit systems. This really should use some
better print formatter, but for the lack of it, do it this way.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Get rid of nvmxip_mmio_rawread() and just implement the readl()/readq()
reader loop within nvmxip_blk_read(). Cast the destination buffer as
needed and increment the read by either 4 or 8 bytes depending on if
this is systemd with 32bit or 64bit physical address.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Perform all the block device creation only once, after the driver itself
successfully bound. Do not do this in uclass post bind, as this might be
triggered multiple times. For example the ut_dm_host test triggers this
and triggers a memory leak that way, since there are now multiple block
devices created using the blk_create_devicef() .
To retain the old probe-on-boot behavior, set DM_FLAG_PROBE_AFTER_BIND
flag in uclass post_bind callback, so the driver model would probe the
driver at the right time.
Rename the function as well, to match similar functions in
other block-related subsystems, like the mmc one.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The current CI test worked by sheer luck, the g_dev global pointer
in the fwu library was never initialized and the test equally well
failed on sandbox64. Trigger the main loop in sandbox tests too to
initialize that global state, and move the sandbox specific exit
from fwu_boottime_checks after g_dev is initialized.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reset gd->cur_serial_dev pointer to avoid calling non-relocated code
from relocated code if a serial driver is not found and
CONFIG_REQUIRE_SERIAL_CONSOLE is disabled.
Here is detailed explanation of what this patch is trying to fix.
U-boot calls the serial_find_console_or_panic() function twice.
The first console setup occurs before U-boot relocation in
the serial_init(). This stage uses simple FDT parsing and
assigns gd->cur_serial_dev to a "serial" device that lives in
non-relocated code too.
The second console setup after U-boot relocation(from serial_initialize())
may use full live DT (if OF_LIVE enabled) probe sequence with buses,
clocks, resets, etc... And if the console setup fails at this step,
than we should be caught by panic_str("No serial driver found").
But... If we disable CONFIG_REQUIRE_SERIAL_CONSOLE, than we
return from serial_init() with gd->cur_serial_dev pointing
to the "old"(non-relocated) serial device.
And if this area, where "old" serial device is placed, is changed
(e.g. Linux kernel may be relocated at this address), than we will get
an unexpected crash on the next call of printf().
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
The make by default cuts off the stdout output from external tools,
so all error messages from the image-host are not shown in a make
output. Besides that, it is a common approach to use stderr stream
for error messages.
Use stderr for all error messages in image-host.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Simon Glass <sjg@chromium.org>
When the Broadcom STB PCIe controller is initialized, it must be set
into one of three CLKREQ# modes: "none"/"aspm"/"l1ss". The Linux driver,
through today, hard-codes "aspm" since the vast majority of boards using
this driver have a fixed PCIe bus with the CLKREQ# signal wired up.
The Raspberry Pi CM4, however, can be connected to a plethora of PCIe
devices, some of which do not connect the CLKREQ# line (they just leave
it floating). So "aspm" mode is no longer appropriate in all cases. In
Linux, there is a proposed patchset [1] to determine the proper mode.
This doesn't really make sense in U-Boot's case, so we just change the
assumption from "aspm" to "none" (which is always safe).
This patch DOES resolve a real-world crash that occurs when U-Boot is
running on a Raspberry Pi CM4 installed in slot 3 of a Turing Pi 2
cluster board.
[1]: https://lore.kernel.org/all/20230428223500.23337-1-jim2101024@gmail.com/
Signed-off-by: Sam Edwards <CFSworks@gmail.com>
Since the initial U-Boot driver was ported here from Linux, the latter
has had a few changes for robustness/stability. This patch brings over
two of them:
- Do not attempt to access the configuration space of a PCIe device if
the link has gone down, as that will result in an asynchronous SError
interrupt which will crash U-Boot.
- Wait for the recommended 100ms after PERST# is deasserted.
I sent this patch while debugging a crash involving PCIe, but these
are unrelated improvements. I do not believe that this patch fixes any
real-world bug.
Signed-off-by: Sam Edwards <CFSworks@gmail.com>
First set of u-boot-at91 features for the 2023.10 cycle:
This feature set includes a new board sama5d29 Curiosity, and various
fixes and alignments for sam9x60 and sam9x60 curiosity board.
To quote the author:
This patchset aims to bring two capsule related tasks under the U-Boot
build flow.
The first task is related to generation of capsules. The capsules can be
generated as part of U-Boot build, and this is being achieved through
binman, by adding a capsule entry type. The capsules can be generated by
specifying the capsule parameters as properties under the capsule entry
node.
The other task is the embedding of the public key into the platform's
DTB. The public key is in the form of an EFI Signature List(ESL) file
and is used for capsule authentication. This is being achieved by adding
the signature node containing the capsule public key in the platform's
DTB.
Corresponding changes have also been made to the test setup of the EFI
capsule update feature. The ESL public key file was embedded into the
sandbox platform's test.dtb as part of the test setup, post U-Boot
build. This is now no longer needed as the embedding of the ESL happens
as part of the build.
Secondly, the capsules needed for testing the EFI capsule update feature
were being generated through the invocation of the mkeficapsule tool.
This setup has also been changed to introduce generation of these
capsules through binman.
The document has been updated to reflect the above changes.
Update the document to specify how the EFI Signature List(ESL) file
can be embedded into the platform's dtb as part of the U-Boot build.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The public key EFI Signature List(ESL) needed for capsule
authentication is now embedded into the platform's DTB as part of the
build. Remove the superfluous logic from the test setup.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Add the path to the public key EFI Signature List(ESL) file for the
sandbox variants which enable capsule authentication. This ESL file
gets embedded into the platform's device-tree as part of the build.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
The EFI capsule authentication logic in u-boot expects the public key
in the form of an EFI Signature List(ESL) to be provided as part of
the platform's dtb. Currently, the embedding of the ESL file into the
dtb needs to be done manually.
Add a target for generating a dtsi file which contains the signature
node with the ESL file included as a property under the signature
node. Include the dtsi file in the dtb. This brings the embedding of
the ESL in the dtb into the U-Boot build flow.
The path to the ESL file is specified through the
CONFIG_EFI_CAPSULE_ESL_FILE symbol.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
At the time of building the DTB, some dtsi files can be selected for
inclusion. Have these dtsi files as dependencies for the DTB
target. This also ensures generation or updating the dtsi files if
need be.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
At the time of building a device-tree file, all the *u-boot.dtsi files
are looked for, in a particular order, and the first file found is
included. Then, the list of files specified in the
CONFIG_DEVICE_TREE_INCLUDES symbol are included.
Combine these files that are to be included into a variable, and then
include all these files in one go.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
When running the trace test on the sandbox platform, the current size
of 16MiB is no longer large enough for capturing the entire trace
history, and results in truncation. Use a size of 32MiB for the trace
buffer on the sandbox platform while running the trace test.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The EFI capsules can now be generated as part of U-Boot build, through
binman. Highlight these changes in the documentation.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Acked-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Support has been added for generating the EFI capsules through
binman. Make changes in the EFI capsule update testing feature to
generate capsules through binman.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Add support in binman for generating EFI capsules. The capsule
parameters can be specified through the capsule binman entry. Also add
test cases in binman for testing capsule generation.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a bintool for generating EFI capsules. This calls the mkeficapsule
tool which generates the capsules.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable the EFI capsule update code on all sandbox variants. This was
already enabled on the sandbox, sandbox64 and sandbox_flattree
variants. The rest of the variants also have the EFI capsule update
module enabled now. With this commit, the mkeficapsule tool also gets
enabled on all variants.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the private keys and public key certificates which are to be used
for capsule authentication while testing the EFI capsule update
functionality. There are two pairs of private and public keys, good
and bad. The good key pair will be used for signing capsules, whilst
the bad key pair is to be used as malicious keys for testing
authentication failure cases. The capsule_pub_key_good.crt is also
converted to an EFI Signature List(ESL) file, SIGNER.esl, which is
embedded in the platform's device-tree for capsule authentication.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support to build a tool from source with a list of commands. This
is useful when a tool can be built with multiple commands instead of a
single command.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Copied as is from Linux Kernel release v6.4.
(dts file is still the same in Linux v6.5-rc7 but was moved to vendor
sub-directories with v6.5-rc1.)
Button works out of the box now if the following config options are
enabled: CONFIG_BUTTON, CONFIG_BUTTON_GPIO, CONFIG_CMD_BUTTON,
CONFIG_DM_GPIO.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
If CONFIG_LED and CONFIG_LED_GPIO are enabled, it is not necessary to
initialize the RGB LED on the board by manually setting hardcoded GPIOs
anymore. Everything is well defined in dts and can be used like on
boards of other vendors.
Keep the old behaviour as fallback, though.
With all this in place enabling CONFIG_CMD_LED gives us a working 'led'
command on the U-Boot shell.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Copied as is from Linux Kernel release v6.4.
(dts file is still the same in Linux v6.5-rc7 but was moved to vendor
sub-directories with v6.5-rc1.)
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Since commit 61040097a9 ("reset: at91: Add reset driver for basic
assert/deassert operations") the compatible "microchip,sam9x60-rstc" for
the sam9x60 reset controller in sam9x60.dtsi is not handled by
CONFIG_SYSRESET_AT91 anymore, but by CONFIG_RESET_AT91 now. This
resulted in the following error message, when trying to reset from
U-Boot shell:
U-Boot> reset
resetting ...
System reset not supported on this platform
### ERROR ### Please RESET the board ###
Fixed by enabling the new driver in the relevant defconfigs. Tested on
sam9x60-curiosity board. Defconfigs for sam9x60ek adapted in the same
way, but without testing. These should be all sam9x60 boards affected
in U-Boot here.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
The board has two SD card slots and we have two defconfigs for booting
from either the first (micro SD) named 'sam9x60_curiosity_mmc_defconfig'
or the second (full size SD) named 'sam9x60_curiosity_mmc1_defconfig'.
For comparable Microchip boards (sama5d27-som1-ek, sama5d29-curiosity,
sama7g5ek) with two card slots the defconfigs only differ in BOOTARGS,
BOOTCOMMAND, and ENV_FAT_DEVICE_AND_PART and the same should be the case
for sam9x60_curiosity.
Here the 'mmc1' config has more options enabled to support the raw NAND
flash populated on the board, so the 'mmc' config (for mmc0) was adapted
by enabling additional options, instead of removing options from mmc1.
The 'mem=128M' argument can be dropped from kernel command line, because
it is redundant to memory node in dts in both Linux and U-Boot:
memory@20000000 {
reg = <0x20000000 0x8000000>;
};
Signed-off-by: Alexander Dahl <ada@thorsis.com>
First, update CI to using gcc-13.2 from 13.1, and rebuild the CI
containers. This is needed because the second part adds utilities for
tests and provides, to quote the author:
This updates the ChromiumOS bootmeth to detect multiple kernel
partitions on a disk.
It also includes minor code improvements to the partition drivers,
including accessors for the optional fields.
This series also includes some other related tweaks in testing.
The latest kernel.org toolchains for gcc are now 13.2.0, so upgrade to
that.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
The existing ChromiumOS bootmeth only supports reading a single kernel
partition, either 2 or 4. In fact there are normally two options
available.
Use the GUID to detect kernel partitions, with the BOOTMETHF_ANY_PART
flag, so that bootstd does not require a valid filesystem before calling
the bootmeth.
Tidy up and improve the logging while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
[trini: Add missing select of PARTITION_TYPE_GUID]
Signed-off-by: Tom Rini <trini@konsulko.com>
Some bootmeths support scanning a partition without a filesystem on it.
Add a flag to support this.
This will allow the ChromiumOS bootmeth to find kernel partition, which
are stored in a special format, without a filesystem.
Signed-off-by: Simon Glass <sjg@chromium.org>
The ChromiumOS bootmeth has no tests at present. Before adding more
features. add a basic test.
This creates a disk which can be scanned by the bootmeth, so make sure
things work. It is quite rudimentary, since the kernel is faked, the root
disk is missing and there is no cmdline stored.
Enable the bootmeth for snow so it can build the unit test.
Signed-off-by: Simon Glass <sjg@chromium.org>
We currently use mmc4 for tests. Update the function which sets this up
so that it can handle any device.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present 'bootflow list' shows <NULL> for the filename when it is not
present. Show an empty string instead, since that is more user-friendly.
Signed-off-by: Simon Glass <sjg@chromium.org>
These are currently created in the source directory, which is not ideal.
Move them to the persistent-data directory instead. Update the test so
skip validating the filename, since it now includes a full path.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some pytests create files in the persistent-data directory. It is useful
to be able to access these files in C tests. Add a function which can
locate a file given its leaf name, using the environment variable set
up in test/py/conftest.py
Signed-off-by: Simon Glass <sjg@chromium.org>
These should be in the header file for easy browsing, not in the source
code. Move them and add a missing Return on one of the functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Follow the correct path in device_probe() when and event handler fails.
This avoids getting into a strange state where the device appears to be
activated but is not.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a little more debugging for the initial signature check. Drop the
pointless check for NULL. Also set a log category while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
This field is only present when a CONFIG is set. To avoid annoying #ifdefs
in the source code, add an accessor. Update the only usage.
Note that the accessor is optional. It can be omitted if it is known that
the option is enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
This field is only present when a CONFIG is set. To avoid annoying #ifdefs
in the source code, add accessors. Update all code to use it.
Note that the accessor is optional. It can be omitted if it is known that
the option is enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
This field is only present when a CONFIG is set. To avoid annoying #ifdefs
in the source code, add accessors. Update all code to use it.
Note that the accessor is optional. It can be omitted if it is known that
the option is enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some internal functions could do with a few comments, to explain what they
do. Add these, to make the code easier to follow.
Signed-off-by: Simon Glass <sjg@chromium.org>
The dev_ prefix is a hangover from the pre-driver model days. The device
is now a different thing, with driver model. Update the mac code to
just use 'desc'.
Signed-off-by: Simon Glass <sjg@chromium.org>
The dev_ prefix is a hangover from the pre-driver model days. The device
is now a different thing, with driver model. Update the iso code to
just use 'desc'.
Signed-off-by: Simon Glass <sjg@chromium.org>
The dev_ prefix is a hangover from the pre-driver model days. The device
is now a different thing, with driver model. Update the efi code to
just use 'desc'.
Signed-off-by: Simon Glass <sjg@chromium.org>
The dev_ prefix is a hangover from the pre-driver model days. The device
is now a different thing, with driver model. Update the dos code to
just use 'desc'.
Signed-off-by: Simon Glass <sjg@chromium.org>
The dev_ prefix is a hangover from the pre-driver model days. The device
is now a different thing, with driver model. Update the amiga code to
just use 'desc'.
Signed-off-by: Simon Glass <sjg@chromium.org>
The dev_ prefix is a hangover from the pre-driver model days. The device
is now a different thing, with driver model. Update the partition code to
just use 'desc', as is done with driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
To quote the author:
So far cedit does not support reading and writing the configuration.
This series add several features related to this:
First, it adds support for using a file on a filesystem. This is in
FDT format and provides enough information to reset the cedit back to
the saved settings.
Second, it adds support for using the U-Boot environment. Since the
environment is generally saved across reboots, this feature provides an
easy way of storing the state on most boards. The variables all have a
'c.' prefix to avoid confusion with other variables.
Finally it adds support for using CMOS RAM. This is commonly used on x86
devices to store BIOS settings. The expo schema provides information on
the register layout.
Some other minor tweaks and improvements are included along the way.
Add a command to read edit settings from CMOS RAM, using the cedit
definition to indicate which registers and bits are used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a command to write cedit settings to CMOS RAM so that it can be
preserved across a reboot. This uses a simple bit-encoding, where each
field has a 'bit position' and a 'bit length' in the schema.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a command to read cedit settings from environment variables so that
they can be restored as part of the environment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a command to write cedit settings to environment variables so that
they can be stored with 'saveenv'.
Signed-off-by: Simon Glass <sjg@chromium.org>
Support writing settings from an expo into a file in FDT format. It
consists of a single node with a two properties for each sceneitem,
one with tag ID chosen by the user and another for its text value.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is related to standard boot, so put it under the same node. This may
simplify schema upstreaming later.
Mention themes in the documentation while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is mentioned in passing in the 'cedit' command. Its file format is
described under `expo`. But it would be better if it had its own entry
in the documentation.
Add a new 'cedit' entry with a few details about this feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tidy up this tool a little:
- define which arguments are needed
- split the enum values out into a header file
- warn if no enum values are found
- display the dtc error if something goes wrong
- avoid a Python traceback on error
Signed-off-by: Simon Glass <sjg@chromium.org>
Split out the code which prepares the cedit for use, so we can call it
from a test.
Add a log category while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this test out so it can have its own file. Rename the test to use
a cedit_ prefix.
This allows us to drop the check for CONFIG_CMD_CEDIT in the test.
Also we don't need driver model objects for this test, so drop them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Before adding more functions to this interface, create a new header for
the configuration editor.
Fix up the expo header guard while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
The caller reads the ID but menu_build() does this again. Add the ID as
a parameter to avoid this. Return the object created so that the caller
can adjust it.
Signed-off-by: Simon Glass <sjg@chromium.org>
For some operations it is necessary to process all objects in an expo.
Provide an iterator to handle this.
Signed-off-by: Simon Glass <sjg@chromium.org>
To quote the author:
Now that the driver for the Bochs VGA card emulated by QEMU is no longer
limited to x86 architectures, this series enables it on arm and arm64 virtual
machines to provide a graphical interface. In line with that series this also
enables console buffering and USB keyboard.
Tested with the Debian 12 installer using GRUB EFI:
$ tools/buildman/buildman -o build/qemu_arm64 --boards=qemu_arm64 -w
$ cd build/qemu_arm64
$ curl -L -o debian.img \
https://cdimage.debian.org/debian-cd/current/arm64/iso-cd/debian-12.0.0-arm64-netinst.iso
$ qemu-system-aarch64 \
-machine virt -cpu cortex-a53 -m 4G -smp 4 \
-bios u-boot.bin \
-serial stdio -device VGA \
-nic user,model=virtio-net-pci \
-device virtio-rng-pci \
-device qemu-xhci,id=xhci -device usb-kbd -device usb-tablet \
-drive if=virtio,file=debian.img,format=raw,readonly=on,media=cdrom
And with one using extlinux.conf:
$ [...]
$ curl -L -o head.img.gz \
https://deb.debian.org/debian/dists/bookworm/main/installer-arm64/current/images/netboot/SD-card-images/gtk/firmware.none.img.gz
$ curl -L -o partition.img.gz \
https://deb.debian.org/debian/dists/bookworm/main/installer-arm64/current/images/netboot/SD-card-images/gtk/partition.img.gz
$ zcat head.img.gz partition.img.gz >debian.img
$ [...]
Both can get to a graphical installer just fine, in addition to U-Boot
video console showing up in a GTK window.
Add an example qemu-system-aarch64 command that can make U-Boot on QEMU
boot into the Debian Installer, along with resulting console messages
from U-Boot, based on the existing documentation section for the x86
version.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Commit 02be57caf7 ("riscv: qemu: Enable usb keyboard as an input
device") adds PCI xHCI support to QEMU RISC-V virtual machines and
enables using a USB keyboard as one of the input devices. Similarly,
enable those for ARM virtual machines as well.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
Commit 608b80b5b8 ("riscv: qemu: Enable PRE_CONSOLE_BUFFER") enables
buffering console messages for QEMU RISC-V virtual machines so those
printed before the video console is available will still show up on the
display. Similarly, enable it for ARM virtual machines as well.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
Commit 716161663e ("riscv: qemu: Enable Bochs video support") enables
a video console for QEMU RISC-V virtual machines using an emulated Bochs
VGA card. Similarly, enable it for ARM virtual machines as well.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
Add function to flush and invalidate cache over request and response
queue entries, and perform flush and optional invalidate over block
layer data that are passed into the UFS layer. This makes it possible
to use UFS with caches enabled.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Tested-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Use utp_transfer_req_desc pointer to reference to utrdl queue
instead of referencing the queue directly. This makes the code
more consistent. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Tested-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Pass the hba pointer itself to ufshcd_prepare_req_desc_hdr()
instead of duplicating utp_transfer_req_desc access at each
call site. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Tested-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Add UFSHCD_QUIRK_HIBERN_FASTAUTO quirk for host controllers which supports
auto-hibernate the capability but only FASTAUTO mode.
Ported from Linux kernel commit
2f11bbc2c7f3 ("scsi: ufs: core: Add UFSHCD_QUIRK_HIBERN_FASTAUTO")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Tested-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Add UFSHCD_QUIRK_BROKEN_64BIT_ADDRESS for host controllers which do not
support 64-bit addressing.
Ported from Linux kernel commit
6554400d6f66 ("scsi: ufs: core: Add UFSHCD_QUIRK_BROKEN_64BIT_ADDRESS")
with ufs_scsi_buffer_aligned() based on U-Boot generic bounce buffer.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Tested-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
In the case of NETLOOP_SUCCESS, the decimal value of the u32 variable
"net_boot_file_size" is printed using "%d", resulting in negative values
being reported for large file sizes. Fix this by using "%u" to print the
decimal value corresponding to the bytes transferred.
Fixes: 1411157d85 ("net: cosmetic: Fixup var names related to boot file")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Some devices have limited DMA capabilities and require that the
buffers passed to them fit specific properties. Add new optional
callback which can be used at driver level to indicate whether a
buffer alignment is suitable for the device DMA or not. This is
a pass-through callback from block uclass to drivers.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Some devices have limited DMA capabilities and require that the
buffers passed to them fit specific properties. Add new optional
callback which can be used at driver level to indicate whether a
buffer alignment is suitable for the device DMA or not, and
trigger use of generic bounce buffer implementation to help use
of unsuitable buffers at the expense of performance degradation.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Block devices with 4k sectors imply the MBR sectors are also 4k instead
of regular 512B. Avoid hard-coding the 512B sector size and isntead read
the current block device sector size from it, and if the sector size is
larger than 512B, use the block device sector size.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix the following warning produced on qemu-x86_64_defconfig:
"
common/bouncebuf.c: In function ‘bounce_buffer_stop’:
common/bouncebuf.c:82:34: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
82 | dma_unmap_single((dma_addr_t)state->bounce_buffer,
| ^
"
The warning is valid, the pointer has to be up-cast first.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Andrew Davis <afd@ti.com>
Move part_create_block_devices() to blk uclass and unexpose
the function. This can now be internal to the block uclass.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The behavior of the part_blk_*() functions is now identical
to disk_blk_*() functions, switch the former to the later.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Check whether access is out of bounds of the partition and
return an error. This way there is no danger of esp. write
or erase outside of the confines of partition.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Convert the read/write/erase offset from one within a partition
to one within a block device, to correctly access the data on
the block device for both write and erase operations.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
These two functions are basically identical, just call the blk_*()
functions from disk_blk_*() functions. The only difference is that
the disk_blk_*() functions have to use parent block device as the
udevice implementing block device operations.
Add documentation on what those functions really do. The documentation
is not wrong even though it likely does look that way. The write/erase
functions really do not take into account the partition offset. This
will be fixed in the next patch.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The disk_blk_read() can be simplified using blk_read(), the only
things which needs to be handled are the read offset based on the
partition properties, and the block device ops which are coming
from the parent udevice, not the partition udevice.
The later is currently not implemented correctly as far as I can
tell, since the current code extracts block device descriptor from
the parent udevice which is OK, but extracts block device operations
from the partition udevice, which does not seem OK.
Switching to the blk_read() fixes that too.
The dev_get_blk() usage is simplified using UCLASS_PARTITION check.
Add non-confusing documentation what this really does.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
if (device_get_uclass_id(dev) == UCLASS_PARTITION) is always
true, because this disk_blk_read() function calls dev_get_blk()
above and checks its return value for non-NULL. The dev_get_blk()
performs the same device_get_uclass_id(dev) check and returns NULL
if not UCLASS_PARTITION. Drop the duplicate check.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Handle both 32bit and 64bit systems, i.e. sandbox and sandbox64
the same way drivers/cpu/cpu_sandbox.c sets those ACPI tables up.
This fixes "$ ./u-boot -Tc 'ut dm dm_test_acpi_write_tables'"
test failure on sandbox64.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Drop the 'ut' prefix, this is superfluous and not present in
any of the other ut tests.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Use built-in ffs/fls on ARM, fix a PIE issue in SPL on ARMv8, bcm283x
and mediatek updates, whitespace fix in UFS uclass, make CI use
"tools-only" defconfig for more tests, add TI TCA9554 GPIO support,
cache alignment fix for SCSI, and fix a problem with
SYS_MMCSD_RAW_MODE_ARGS_SECTOR in SPL.
When running tools for various tests use the tools-only build rather
than sandbox_spl. We used sandbox_spl here for historical reasons that
are no longer true.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When Falcon Mode is enabled, SPL needs to check the value of
CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR. Unfortunately, it was using the
CONFIG_VAL(SYS_MMCSD_RAW_MODE_ARGS_SECTOR) which converts it into
CONFIG_SPL_SYS_MMCSD_RAW_MODE_ARGS_SECTOR when CONFIG_SPL_BUILD is
enabled. CONFIG_SPL_SYS_MMCSD_RAW_MODE_ARGS_SECTOR does not exist in
common/spl/Kconfig. Replaced with
defined(CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR).
Signed-off-by: Elena Popa <elena.popa@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
MT7988 has a t-phy and an x-phy controller. There is already a driver for
t-phy so we can add USB support for this phy type.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Ethernet on Bananapi-r3 is broken after
commit bd70f3cea3 ("net: mediatek: add support for SGMII 1Gbps auto-negotiation mode")
because changes from this commit were not applied to bpi-r3 devicetree too:
commit aef54ea16c ("arm: dts: medaitek: convert gmac link mode to 2500base-x")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
Builds for Raspberry Pi targets fail when CONFIG_DISPLAY_CPUINFO is
enabled and following error can be seen -
common/board_f.o:(.rodata.init_sequence_f+0x90):
undefined reference to `print_cpuinfo'
Added implementation of function "print_cpuinfo"
Signed-off-by: Naveen Kumar Chaudhary <naveenchaudhary2010@hotmail.com>
When PIE is enabled in start.S, u-boot/-spl use __rel_dyn_start
and _rel_dyn_end symbol to be loaded to and executed at a
different address than it was linked at.
u-boot-spl.lds is used in SPL build, but relocation information
section(.rela*) were discarded.
In line number 80 in arch/arm/cpu/armv8/u-boot-spl.lds
/DISCARD/ : { *(.rela*) }
If PIE enabled in SPL, __rel_dyn_start which is defined as
.rel_dyn_start in sections.c will be apended to the end of
.bss section.
In our ASPEED case, size of .bss section would let .rel_dyn_start
without 8-byte alignment, leading to alignment fault when
executing ldp instuction in pie_fix_loop.
Signed-off-by: Kevin Chen <kevin_chen@aspeedtech.com>
Since ARMv5, the clz instruction allows for efficient implementation of
ffs/fls with builtins. Until ARMv7 (with Thumb-2), this instruction is
only available in ARM mode. LTO makes it difficult to force specific
functions to be in ARM mode, as it is effectively a form of very
aggressive inlining. To work around this, fls/ffs are implemented in
assembly for ARMv5 and ARMv6 when compiling U-Boot in Thumb mode.
Overall, this saves around 75 bytes per call.
This code is synced with v5.15 of the Linux kernel.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Sync all am642-evm/am642-sk related DT files
with Linux v6.5-rc1.
- drop timer1 in favor of main_timer0 in am64-main.dtsi.
Need to delete clock & power domain properties of
main_timer1 in -r5.dts else won't boot. This is because
timer_init is done during rproc_start to start System Firmware,
but we can't do any clock/power-domain operations before
System Firmware starts.
- same constraint applies to main_uart0
- drop cpsw3g custom DT property 'mac_efuse' and custom
DT node cpsw-phy-sel as driver picks these from standard
property/node.
- include board dts file in -r5 dts file to avoid duplication
of nodes. Include -u-boot.dtsi on top.
- drop duplicate nodes in -r5 dts and -u-boot.dtsi
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Tested-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
This reverts commit 28a4c31134.
This node should be in the board DT file and should come from upstream.
Moreover, this PMIC is no present on all variants of am642-sk
and will need a separate board DT file.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Tested-by: Nishanth Menon <nm@ti.com> #SK-AM64B
AM64-HSEVM is AM64-GPEVM with High Security Device.
Gets rid of "Unidentified board claims AM64-HSEVM in eeprom header".
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Andrew Davis <afd@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Tested-by: Nishanth Menon <nm@ti.com> #SK-AM64B
To quote the author:
This series adds support for SGMII mode to the CPSW driver to enable the
functionality on TI's J7200 SoC.
Supporting SGMII mode also requires changes to the WIZ driver which acts
as a wrapper for the SerDes used by the CPSW MAC to transmit data to the
Ethernet PHY daughtercard mounted on the I2C GPIO Expander 2 connector
on the J7200 EVM.
Powering on and resetting the Ethernet PHY requires MDIO support which
is added to the CPSW driver.
For supporting DMA transactions from the MAIN CPSW instance to the A72
Host on J7200 SoC, the corresponding PSI-L endpoint information is added
for the J721E SoC, which is applicable to J7200 SoC as well.
The SGMII daughtercard used for testing SGMII mode has TI's DP83869 PHY.
Thus, enable the config for DP83869 driver functionality. Also, enable
GPIO HOG config.
The MAIN CPSW0 instance of CPSW Ethernet Switch on TI's J7200 SoC
supports SGMII mode. To enable support for utilizing the SGMII
daughtercard with TI's DP83869 PHY, enable the corresponding config.
Also, since the SGMII daughtercard is connected to the I2C GPIO
Expander 2 connector on the J7200 EVM, powering on the Ethernet PHY and
resetting it requires GPIO Hogging capability. Enable it as well.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Select the same mac divider for SGMII too as the one being used for
QSGMII.
Enable full rate divider configuration support for J721E_WIZ_10G for
SGMII.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Enhance the AM65 CPSW NUSS driver to perform a MDIO reset using a GPIO
line. Logic is also added to perform a pre and post delay around reset
using the optional 'reset-delay-us' and 'reset-post-delay-us' properties.
This is similar to the reset being performed in the Linux kernel. The
reset is done once when the CPSW MDIO bus is being initialized.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
The PSIL endpoint data for J721E currently covers only the MCU domain
CPSW0 instance. Add the data for the MAIN domain CPSW0 as well to allow
the MAIN domain Ethernet ports to be usable on any platform using J721E
SoC.
Additionally, since J721E's PSIL endpoint data is applicable to J7200
SoC as well, the MAIN CPSW0 instance on J7200 will also be usable now.
Signed-off-by: Suman Anna <s-anna@ti.com>
[s-vadapalli@ti.com: Update commit message indicating support for J7200]
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
- Assorted PCI-related fixes, add Apple Type-C PHY support, semihosting
updates, fix a FAT corner-case, update the help on the pxe cmd and
clean up the gpio uclass slightly.
The current gpio-uclass design uses name field in struct gpio_dev_priv as
an indicator that GPIO is claimed by consumer. This overloads the function
of name field and does not work well for named pins not configured as GPIO
pins.
Introduce separate bitfield array as the claim indicator.
This unbreaks dual-purpose AF and GPIO operation on STM32MP since commit
2c38f7c318 ("pinctrl: pinctrl_stm32: Populate uc_priv->name[] with pinmux node's name")
where any pin which has already been configured as AF could no longer be
claimed as dual-purpose GPIO. This is important for pins like STM32 MMCI
st,cmd-gpios .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently the "help" displays pxe command help text like this:
=> help
...
printenv - print environment variables
pxe - commands to get and boot from pxe files
To use IPv6 add -ipv6 parameter
qfw - QEMU firmware interface
...
This does not read clearly. Remove the IPv6 stuff as it is in
the detailed help text so that it fits just a single line.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a new DM driver supporting FTPCI100 IP used in SoC designs.
This implementation is not based on the old non-DM ftpci100 code
dropped from U-Boot.
Enable the driver in sandbox_defconfig to test compilability.
Signed-off-by: Sergei Antonov <saproj@gmail.com>
The product of two 32 bit integers is a 32 bit integer. Hence
clustcount * bytesperclust may overflow on > 4 GiB devices.
Change the type of clustcount.
Fixes: cb8af8af5b ("fs: fat: support write with non-zero offset")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This function only ever returns 0, but may not assign the second
parameter. Same thing for device_find_next_child(). Do not assign
ret to stop proliferation of this misuse.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This is merely a dummy driver that makes sure the DWC3 XHCI driver
finds its reset and PHY controllers. We rely on iBoot to set up
the PHY for us.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
The Apple hardware supports 64-bit prefetchable memory windows so
enable CONFIG_SYS_PCI_64BIT. This fixes BAR assignments for the
Broadcom Ethernet controller used in some of the desktop machines.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
To quote the author:
The commit 4fcba5d556 ("regulator: implement basic reference counter")
have made it more important to keep fixed/gpio regulators enable/disable
state in balance.
This series fixes an inbalance in the mmc_dw driver and changes to use
the more relaxed regulator_set_enable_if_allowed function for a few
other drivers.
The regulator_set_enable_if_allowed function is more relaxed and will
return ENOSYS if the provided regulator is NULL or when DM_REGULATOR
was disabled. Using the following call convention should be safe:
ret = regulator_set_enable_if_allowed(<supply>, <true|false>);
if (ret && ret != -ENOSYS)
return ret;
With the commit 4fcba5d556 ("regulator: implement basic reference
counter"), keeping regulator enablement in balance become more important.
Disable vqmmc-supply before signal voltage is changed to keep regulator
enable counter in balance.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
With the commit 4fcba5d556 ("regulator: implement basic reference
counter") the return value of regulator_set_enable may be EALREADY or
EBUSY for fixed/gpio regulators.
Change to use the more relaxed regulator_set_enable_if_allowed to
continue if regulator already was enabled or disabled.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # P895 Tegra 3;
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # rockpro64-rk3399
With the commit 4fcba5d556 ("regulator: implement basic reference
counter") the return value of regulator_set_enable may be EALREADY or
EBUSY for fixed/gpio regulators.
Change to use the more relaxed regulator_set_enable_if_allowed to
continue if regulator already was enabled or disabled.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Marek Vasut <marex@denx.de>
With the commit 4fcba5d556 ("regulator: implement basic reference
counter") the return value of regulator_set_enable may be EALREADY or
EBUSY for fixed/gpio regulators.
Change to use the more relaxed regulator_set_enable_if_allowed to
continue if regulator already was enabled or disabled.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # rockpro64-rk3399
Reviewed-by: Marek Vasut <marex@denx.de>
With the commit 4fcba5d556 ("regulator: implement basic reference
counter") the return value of regulator_set_enable may be EALREADY or
EBUSY for fixed/gpio regulators.
Change to use the more relaxed regulator_set_enable_if_allowed to
continue if regulator already was enabled or disabled.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # rockpro64-rk3399
Support booting ChromiumOS on ARM devices using FIT. Add an entry into the
boot implementation which does not require a command line. This can be
expanded over time as the bootm code is refactored.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some bootflows (such as EFI and ChromiumOS) delay reading the kernel until
it is needed to boot. This saves time when scanning and avoids needing to
allocate memory for something that may never be used.
To permit reading of these files, add a new 'bootflow read' command.
Signed-off-by: Simon Glass <sjg@chromium.org>
Provide an option to dump this information if available.
Move the funciion prototype to the common x86 header. Allow the command
line to be left out since 'bootflow info' show this itself and it is
not in the correct place in memory until the kernel is actually booted.
Fix a badly aligned heading while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use the two new functions to separate reading of the ChromiumOS info from
the partition from actually reading the kernel and booting it.
Signed-off-by: Simon Glass <sjg@chromium.org>
The code to read the ChromiumOS information from the partition is
currently all in one function.
Create a new function which reads the kernel, assuming that the metadata
has been parsed.
For now this function is not used. Future work will plumb it in.
Signed-off-by: Simon Glass <sjg@chromium.org>
The code to read the ChromiumOS information from the partition is
currently all in one function. It reads the entire kernel, which is
unnecessary unless it is to be booted.
Create a new function which reads just the minimum required data from the
disk, then obtains what it needs from there.
For now this function is not used. Future work will plumb it in.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some bootmeths need to store their own information related to the
bootflow, in addition to the generic information in struct bootflow.
Add a pointer for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Create a new private structure to hold information gleaned from the disk.
This will allow separation between reading of the bootflow information and
(later) reading the whole kernel.
Signed-off-by: Simon Glass <sjg@chromium.org>
We want to avoid using #ifdefs around header files and in the code. It
makes sense to collect the various functions used for loading images into
a single header which can be included by all architectures. The best place
for this is the arch-neutral bootm.h header, so use that.
Move some zimage functions into this bootm.h header.
Signed-off-by: Simon Glass <sjg@chromium.org>
Create a common base from which the other parts are offset and make all
of the offsets related to that. This makes the code a little easier to
read.
Use X86_ prefixes for the two values which are x86-specific.
Drop OFFSET_BASE since it is available in a header field.
Drop the unnecessary 'start' variable too.
Signed-off-by: Simon Glass <sjg@chromium.org>
Decode the kernel start and size using the structures provided. This
accesses the same data, just in a cleaner way.
Add some logging for some of the fields in the kernel preamble.
Signed-off-by: Simon Glass <sjg@chromium.org>
ChromiumOS allows a kernel to be on either partition 2 or 4. Add support
for scanning both and using the first one we find with a suitable
signature.
Record the partition which is used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a header file with structures for booting ChromiumOS, taken from the
vboot tree. Using these makes it easier to understand the code.
Note that the code style has not been updated for U-Boot, with use of
uint64_t, __attribute__((packed)) and one comment-style nit. This should
make it easier to keep the code in sync. It was taken from commit:
5b8596ce ("2sha256_arm: Fix data abort issue")
Update the CHROMEOS string to use the defined values.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move the code which reads a partition into its own function. Add a
constant for the number of bytes to 'probe' at the start of the partition.
Signed-off-by: Simon Glass <sjg@chromium.org>
- Rework the arch linker scripts to be consistent for all, support
Kconfig fragments in the board directory and fix some Kconfig options
that were hex-type by default of 0 not 0x0.
Add support to config fragments (.config) located in the /board
directory. This will allow only base defconfigs to live in /configs and
all fragments to live in their respective device directory in /board/..
Signed-off-by: Jason Kacines <j-kacines@ti.com>
Now all linker symbols are declared as type char[]. Though we can
reference the address via both the array name 'var' and its address
'&var'. It's better to unify them to avoid confusing developers.
This patch converts all '&var' linker symbol refrences to the most
commonly used format 'var'.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
1. Convert all linker symbols to char[] type so that we can get the
corresponding address by calling array name 'var' or its address
'&var'. In this way, we can avoid some potential issues[1].
2. Remove unused symbol '_TEXT_BASE'. It has been abandoned and has
not been referenced by any source code.
3. Move '__data_end' to the arch x86's own sections header as it's
only used by x86 arch.
4. Remove some duplicate declared linker symbols. Now we use the
standard header file to declare them.
[1] This patch fixes the boot failure on MIPS target. Error log:
SPL: Image overlaps SPL
Fixes: 1b8a1be1a1 ("spl: spl_legacy: Fix spl_end address")
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
It is not a parse error to have a default value of "0" for a "hex" type
entry, instead of "0x0". However, "0" and "0x0" are not treated the
same even by the tools themselves. Correct this by changing the default
value from "0" to "0x0" for all hex type questions that had the
incorrect default. Fix one instance (in two configs) of a default of "0"
being used on a hex question to be "0x0". Remove the cases where a
defconfig had set a value of "0x0" to be used as the default had been
"0".
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If an error message contains a function name, it should match the name of
the function throwing the message.
Fixes: 7739d93d82 ("pci: Match region flags using a mask")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The btrfs_decompress() function mostly (u32)-1 on error but it can
also return -EPERM or other kernel error codes from zstd_decompress().
The "ret" variable is an int, so we could just check for negatives.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Qu Wenruo <wqu@suse.com>
The x509_cert_parse() and pkcs7_parse_message() functions return error
pointers. They don't return NULL. Update the checks accordingly.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This should be allocating the memory for "item" instead of "menu".
The item struct is 48 bytes instead of 96 (assuming a 64bit system)
so this saves a little memory.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This line break is not done correctly. We don't want to have all those
tabs in the printed output.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The u16_strlcat() is in units of u16 not bytes. So the limit needs to
be ARRAY_SIZE() instead of sizeof().
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
We know that "pa" is non-NULL so it's nicer to just return zero instead
of return !pa. This has no effect on runtime behavior.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The "oftree_count" is the number of entries which have been set in
the oftree_list[] array. If all the entries have been initialized then
this off by one would result in reading one element beyond the end
of the array.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
If btrfs_read_fs_root() fails with -ENOENT, then we go to the next
entry. Fine. But if it fails for a different reason then we need
to clean up and return an error code. In the current code it
doesn't clean up but instead dereferences "root" and crashes.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Qu Wenruo <wqu@suse.com>
The ec_command_inptr() function returns negative error codes or
the number of bytes that it was able to read. The cros_ec_get_sku_id()
function should return negative error codes. Right now it returns
positive error codes or negative byte counts.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The VNBYTES() macro needs to have parentheses to prevent some (harmless)
macro expansion bugs. The VNBYTES() macro is used like this:
VID_TO_PIXEL(x) * VNBYTES(vid_priv->bpix)
The * operation is done before the / operation. It still ends up with
the same results, but it's not ideal.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The parentheses are in the wrong place so this passes the number of
bytes to write as "sizeof(index_0) != TPM_SUCCESS" when just
"sizeof(index_0)" was intended. (1 byte vs 4 bytes).
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
This returns the wrong variable. It ends up returning NULL when it was
suppose to return an error pointer.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Both the Linux kernel and libbsd agree that strlcpy() should always
return strlen(src) and not include the NUL termination. The incorrect
U-Boot implementation makes it impossible to check the return value for
truncation, and breaks code written with the usual implementation in
mind (for example, fdtdec_add_reserved_memory() was subtly broken).
I reviewed all callers of strlcpy() and strlcat() and fixed them
according to my understanding of the intended function.
This reverts commit d3358ecc54 and adds
related fixes.
Fixes: d3358ecc54 ("lib: string: Fix strlcpy return value")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Basically the same as on sam9x60-ek. Same as in Linux. NAND flash is
correctly detected when booting into U-Boot:
U-Boot 2023.07-rc6-00005-g12719f75dc-dirty (Jul 05 2023 - 13:06:35 +0000)
CPU: SAM9X60 128MiB DDR2 SiP
Crystal frequency: 24 MHz
CPU clock : 600 MHz
Master clock : 200 MHz
Model: Microchip SAM9X60 Curiosity
DRAM: 128 MiB
Core: 145 devices, 22 uclasses, devicetree: separate
NAND: 512 MiB
MMC: sdhci-host@80000000: 0, sdhci-host@90000000: 1
Loading Environment from FAT... Unable to read "uboot.env" from mmc0:1...
In: serial
Out: serial
Err: serial
Net: eth0: ethernet@f802c000
Hit any key to stop autoboot: 0
Signed-off-by: Alexander Dahl <ada@thorsis.com>
- nodes moved
- using node references by label instead of dulicating the node tree
Makes it easier to compare with the dts file from Linux kernel.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
The user guide says it's a Microchip 24AA025E48 serial EEPROM, which is
a 2-Kbit I2C Serial EEPROM with EUI-48™ Identity. This is the chip
actually populated on board EV40E67A rev 4.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
No functional changes, but this:
- reorder nodes (ordered by memory offset as in Linux)
- add label to pinctrl node name for easier reference in board files
- fix whitespace
Diff to sam9x60.dtsi in Linux is much better readable now.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
2023-08-02 08:54:21 +03:00
3591 changed files with 98964 additions and 36756 deletions
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
