In scmi_clk_probe(), in case of CLK_CCF is not enabled, parent private
data is not set, so in scmi_clk_gate(), an uninitialized priv struct is
retrieved.
SCMI request is performed either using scmi_clk_state_in_v1 or
scmi_clk_state_in_v2 struct depending of the unpredictable value of
priv->version which leads to error during SCMI clock enable.
Issue detected on STM32MP157C-DK2 board using the SCMI device tree
stm32mp157c-dk2-scmi.dts.
Fixes: 0619cb3203 ("firmware: scmi: Add clock v3.2 CONFIG_SET support")
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Later versions of the datasheet makes it clear D3 do not have any
realtime module stop control registers (RMSTPCRx). Remove the
manipulation of them from the module clock table to match this.
Suggested-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Since commit a2bd99549c ("clk: renesas: Tear clock controller down
last before booting OS") enabling the module gated by bit 8 in MSTP4
prevents Linux from booting. The bits 8 and 7 of MSTP4 where only
documented in early versions of the datasheet and have since been
removed.
To allow Linux to boot update the MSTP4 enable value to reflect the
hardware default, 0x80.
Suggested-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
As in Linux with d78c0ced60 ("net: ravb: Make write access to CXR35 first
before accessing other EMAC register"), configure CXR31 and CXR35 correctly
on rzg2. MII mode does not work correctly unless those registers are
properly configured.
Signed-off-by: Mathieu Othacehe <othacehe@gnu.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The scsi_read function incorrectly decrements the block count twice
when handling large disks that trigger the CONFIG_SYS_64BIT_LBA code
path (reads beyond block 268,435,455). The variable 'blks' was being
decremented both inside the 64-bit LBA block and after the successful
scsi_exec() call, causing incorrect block count tracking and data
abort errors on large capacity disks.
Signed-off-by: Balaji Selvanathan <balaji.selvanathan@oss.qualcomm.com>
Tested-by: Tony Dinh <mibodhi@gmail.com>
The config is wrongly written, result
in only support socdk board.
Fixes: 92dcb3ad5d ("cmd/dma: implement dmareset command")
Signed-off-by: Brian Sune <briansune@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The GitHub dependabot tool has reported a "medium" priority bug
CVE-2025-68146, with this package. Update to the patched version.
Reported-by: GitHub dependabot
Signed-off-by: Tom Rini <trini@konsulko.com>
The option should be 'net_lwip' and not 'net lwip' (see all usage of it
in the test code base).
Fixes: 2bac578c5a ("test: allow multiple config options in buildconfigspec")
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Jerome Forissier <jerome.forissier@linaro.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Avoid NULL pointer dereference in case 'env select' is invoked
without parameters, check the arg count and make sure it is at
least 2, otherwise print usage.
The crash is easy to trigger e.g. in sandbox:
$ ./u-boot -Tc "env select"
Fixes: a97d22ebba ("cmd: env: add env select command")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Tested-by: Vincent Stehlé <vincent.stehle@arm.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The alt name for tispl binary is "tispl.bin" and not "tispl", this patch
fixes the documentation to the correct alt name.
Fixes: def64b4937 ("doc: board: Add document for DFU boot on am62x SoCs")
Fixes: 3633fdbb6b ("ti: add support for AM6254atl SiP")
Signed-off-by: Anshul Dalal <anshuld@ti.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Running `wget cacert builtin` leads to a crash in _set_cacert():
Unhandled exception: Load access fault
Function _set_cacert() dereferences variable wget_info.
We must initialize it before executing the cacert sub-command.
Fixes: d3761a31ef ("lwip: split net/lwip/wget.c")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Jerome Forissier <jerome.forissier@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The code to choose the filename to use does not cope with no name set at
all. Firstly the test for a name in net_boot_file_name tests the pointer
rather than the string it points to. Secondly the cleanup on exit in
this case attempts to free a global variable. Fix both issues.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Reviewed-by: Jerome Forissier <jerome.forissier@linaro.org>
Remove duplicate '@parent' field documentation in struct mtk_composite.
There is no need to say the same thing twice.
Also fix spelling mistake in the word "parent" while we're at it.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Currently, the terms of both licenses (GPL 2.0 and BSD-2-Clause) must be
met.
However, before switching to the SPDX license identifier, the license
information in the file begins with:
"libfdt is dual licensed: you can use it either under the terms of
the GPL, or the BSD license, at your option."
Therefore, the missing "OR" between the licenses is added.
Fixes: 3508476 ("libfdt: SPDX-License-Identifier: GPL-2.0+ BSD-2-Clause")
Signed-off-by: Max Merchel <Max.Merchel@ew.tq-group.com>
Improve the image header documentation for v1 header:
- specify this applies to all MMC, not only SD cards,
- specify the offset for SPI flashes,
- specify the key used for RC4 encoding,
- specify what "init" refers to, especially since some configs enable
TPL,
- specify what "init_boot_size" refers to, especially since some configs
enable TPL,
- specify the size of a block,
- add documentation for init_size and init_boot_size,
Note that the offset on the storage medium isn't necessarily 32KiB (64
blocks) for MMC or 0 for SPI flashes, it's just the first offset the
BootROM checks. Barebox[1] lists a few options, though those are
applicable to RK35xx which use the v2 header, so not guaranteed they can
be shared. On RK3399, the binary can at least be stored at offset 0 and
32KiB on SPI flashes.
[1] https://git.pengutronix.de/cgit/barebox/tree/arch/arm/mach-rockchip/bbu.c#n19
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In the last message sent in rockchip_i2c_xfer, the controller is
disabled (see rk_i2c_disable() in rk_i2c_read()/rk_i2c_write()), then
the STOP condition is sent (see rk_i2c_send_stop_bit() in
rockchip_i2c_xfer()) and the controller is disabled once again (see
rk_i2c_disable() right after).
The issue is that re-enabling the controller just to send the STOP
condition doesn't work. When, the controller is disabled, the SCL and
SDA lanes are not driven anymore and thus enter the idle mode where they
are kept high by the external HW pull-up. To send a STOP condition, one
needs to drive the SDA line so that a rising edge happens while SCL is
high. Experimentally (on PX30 and RK3399), when enabling the controller
to send a STOP condition after it's been disabled, the controller only
drives the SDA line to trigger the rising edge for the STOP condition,
leaving SCL undriven (and thus, high). This means, that because SDA is
high before this happens and that we need a rising edge, the controller
drives the SDA line low and then releases it, meaning we trigger a START
condition followed by a STOP condition:
SCL
_________
_____...
__ _____
_____... \/
SDA
^ STOP
^ START
This is illegal in I2C protocol[1]:
5. A START condition immediately followed by a STOP condition (void
message) is an illegal format. Many devices however are designed to
operate properly under this condition.
My guess is that the I2C controller IP knows that it makes only sense to
send a STOP condition after a START condition, meaning the controller is
already driving the SCL line low and neither the device nor controller
drive the SDA line after the last ACK/NACK as there's no need to, then
it needs to drive SDA, release SCL to make it high and then release the
SDA line. However, after it's been disabled, the SCL is already released
so the controller only essentially drives SDA and then releases it.
It happens that this seems to be breaking the SE050 Secure Element after
a few transfers in the middle of a transfer where it starts clock
stretching the bus forever. It may be related to Errata 3.2[2] but the
description of the setup isn't an exact match to the current situation.
It seems to be required to disable the I2C controller between messages
as the Linux kernel states that "The HW is actually not capable of
REPEATED START. But we can get the intended effect by resetting its
internal state and issuing an ordinary START.". Between messages, this
logic seems fine as I get an Sr (repeated START condition) before
starting the next message in the transfer without a STOP condition.
However, we should NOT disable the controller after the last message in
the transfer otherwise we do this illegal START condition followed by
the STOP condition, hence the added check.
[1] https://www.nxp.com/docs/en/user-guide/UM10204.pdf 3.1.10 The target address and R/W bit point 5
[2] https://www.nxp.com/docs/en/errata/SE050_Erratasheet.pdf
Fixes: c9fca5ec88 ("rockchip: i2c: don't sent stop bit after each message")
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Heiko Schocher <hs@nabladev.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The I2C_CON_LASTACK is kind of a misnomer as setting it means sending a
NACK as last byte acknowledge when the controller is in receive mode. It
should therefore be used only when there's no more data to transfer
after this.
Move the comment in the proper if block.
Sync the comment with the Linux kernel's while at it so it's more
explicit.
Fixes: 5deaa53028 ("rockchip: i2c: fix >32 byte reads")
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Heiko Schocher <hs@nabladev.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
I2C_CON_STOP is a flag to be used for the con register, where it is bit
4 to send the STOP condition.
To enable the interrupt the controller sends to tell it's finished
sending the STOP condition, it's the ien register at bit 5.
Let's use the proper offset.
My hunch is that enabling the interrupt is useless as the interrupt
status register is always up-to-date and enabling the interrupt is just
so that the interrupt is available via the GIC. However, U-Boot has no
interrupt support and the logic was working well before this patch. This
is just so people aren't side-tracked when debugging I2C issues on
Rockchip by checking all writes are proper.
Fixes: 3437469985 ("rockchip: Add I2C driver")
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Heiko Schocher <hs@nabladev.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Include the FDT for Radxa ROCK 5T in the FIT, in addition to those for
5B and 5B+, and add board selection code to load the 5T FDT when the
DRAM type is LPDDR5 and ADC channel 5 value is close to 1016.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Include FDTs for both ROCK 5B and 5B+ in the FIT and add board selection
code to load the 5B+ FDT when the DRAM type is LPDDR5 and ADC channel 5
value is close to 4095.
U-Boot 2025.07 (Jul 14 2025 - 21:28:20 +0000)
Model: Radxa ROCK 5B+
SoC: RK3588
DRAM: 8 GiB
Features tested on a ROCK 5B+ v1.2:
- SD-card boot
- eMMC boot
- SPI flash boot
- PCIe/NVMe
- Ethernet
- USB/TCPM
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a helper function based on rockchip_sdram_size() that return what
DRAM type is used on current running board.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The BootROM in Rockchip SoCs will enter maskrom mode when boot firmware
cannot be found in nand/spi/mmc storage.
In maskrom mode the USB OTG port can accept one of two custom commands.
Initially a 0x471 command to load TPL into SRAM. After TPL has been
executed and it has returned back-to-BROM, a 0x472 command to load SPL
into start of DRAM.
Add two binman images that can be used to RAM boot from maskrom mode:
- u-boot-rockchip-usb471.bin that contains TPL to init DRAM.
- u-boot-rockchip-usb472.bin that contains SPL and the normal FIT
payload with i.e. U-Boot proper, TF-A and FDT.
A config fragment rockchip-ramboot.config can be used to enable building
of these two binman images, e.g.:
make generic-rk3588_defconfig rockchip-ramboot.config
These binman images can be used with the proprietary rkbin boot_merger
tool to create a special loader image that can be used with tools such
as rkdeveloptool or rockusb tools to RAM boot from maskrom, e.g.:
Create loader image:
$ ../rkbin/tools/boot_merger ./RK3588MINIALL.ini
Boot from maskrom:
$ rkdeveloptool db u-boot-rockchip-rk3588-loader.bin
or
$ rockusb download-boot u-boot-rockchip-rk3588-loader.bin
Another option that does not require use of proprietary tools is using
open source tools such as rkflashtool or rkusbboot that can load the
binman images directly without any need to first create a special loader
image to RAM boot from maskrom, e.g.:
$ rkflashtool l < u-boot-rockchip-usb471.bin
$ rkflashtool L < u-boot-rockchip-usb472.bin
or
$ rkusbboot u-boot-rockchip-usb471.bin u-boot-rockchip-usb472.bin
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Tested-by: Arnaud Patard <arnaud.patard@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Drop SoC specific TEXT_BASE and use a common TEXT_BASE for all SoCs.
Move the common TEXT_BASE to 8 MiB offset from start of DRAM to help
support RAM boot from maskrom introduced in next patch.
RAM boot from maskrom mode will expect the FIT payload to be located at
2 MiB offset from start or DRAM.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Tested-by: Arnaud Patard <arnaud.patard@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
When one attempts to build Tiger and Jaguar from the same directory,
because Tiger will set the IOMUX to 2 but Jaguar doesn't reset it,
Jaguar will have IOMUX set to 2 if built after Tiger.
This isn't an issue if in separate directories or building Tiger after
Jaguar because the default if missing from the configuration file is 0.
Let's make it explicit that the iomux is 0 for Jaguar.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Upstream TF-A has support for RK3588 since v2.12 so let's document how
to use upstream TF-A instead of the prebuilt binary blob from Rockchip
if one wants to do that.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The instructions are regularly out of date because the generated or
prebuilt binaries are updated and the filename doesn't match our
instructions anymore.
Additionally, since commit 55a95caaef15 ("tools: ddrbin_tool: add
ddrbin_tool.py and update to v1.21 20241211") end of October 2024,
ddrbin_tool doesn't exist anymore and has been replaced by
ddrbin_tool.py python script (which currently isn't an executable) so
let's update these instructions as well.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
We do not perform a check on the value of getsize in get_fatent to
ensure that it will fit within the allocated buffer. For safety sake,
add a check now and if the value exceeds FATBUFBLOCKS use that value
instead. While not currently actively exploitable, it was in the past so
adding this check is worthwhile.
This addresses CVE-2025-24857 and was originally reported by Harvey
Phillips of Amazon Element55.
Signed-off-by: Tom Rini <trini@konsulko.com>
J742S2 SOC is derivative of J784S4, most of build infra of j784s4 is used
to build u-boot for J742S2 EVM board.
Add guide users on how to build for that board.
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
The current FDT decoding tests calculate the memory required
for FDT manipulation by directly adding a fixed margin to
fdt_totalsize(gd->fdt_blob). The static analyzer flagged
"gd->fdt_blob->totalsize" as a tainted value being passed
to fdt_open_into().
Ensure the size is validated by checking that the total size
is within a reasonable maximum FDT limit for unit tests.
Signed-off-by: Adriana Nicolae <adriana@arista.com>
The TI AM43xx HS boards have been using CFG_PRAM to hide the top 64MB
firewalled DRAM memory from U-Boot. However, CFG_PRAM only prevents
U-Boot from relocating into that memory, but it is still open for access
for any other usage.
Therefore, migrate into using CONFIG_SYS_MEM_TOP_HIDE which reduces the
ram size itself ensuring that memory is not visible to U-Boot at all
(either for reloc, or general usage).
Signed-off-by: Beleswar Padhi <b-padhi@ti.com>
The objcopy man-page teaches:
--target=bfdname
Use bfdname as the object format for
both the input and the output file
This implies for --target=efi-app-x86_64 that the input file would have
to be an EFI app.
Objcopy in binutils 2.45 checks this more strictly than previous versions
and refuses to accept an ELF file as input with --target=efi-app-x86_64.
Replace --target by --output-target for building sandbox and x86 EFI
binaries.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Commit c37a668481 ("stm32mp: fix compilation issue with DEBUG_UART")
split the debug UART initialization code into two files, but failed to
update other non-ST boards. This did not lead to noticeable breakage
until debug UART is enabled, which is not the default. Update the
Makefile accordingly to allow debug UART to work.
Fixes: c37a668481 ("stm32mp: fix compilation issue with DEBUG_UART")
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add DRAM settings for 1 GiB variant of DH STM32MP13xx DHCOR SoM
and support for SoM DRAM coding HW straps decoding and automatic
DRAM configuration selection. Enable CONFIG_BOARD_EARLY_INIT_F on
all STM32MP1 DHSOM, as it is required for the HW straps decoding.
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Update DRAM chip type and density comment for 512 MiB DRAM settings for
DH STM32MP13xx DHCOR DHSBC to match the chip on the SoM. No functional
change.
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
STM32MP13xx may have OPTEE-OS at 0xdd000000 even on systems with 1 GiB
of DRAM at 0xc0000000, which is not the end of DRAM anymore. This puts
the OPTEE-OS in the middle of DRAM. Currently, the code sets RAM top to
0xdd000000 and prevents the DRAM range past OPTEE at 0xe0000000..0xffffffff
from being set as cacheable and from being usable. The code also sets the
area over OPTEE as invalid region in MMU tables, which is not correct.
Adjust the code such, that it only ever sets RAM top just before OPTEE
in case the OPTEE is really at the end of DRAM, mainly to be backward
compatible. Furthermore, adjust the MMU table configuration such, that
the regions over the OPTEE are simply skipped and not reconfigured, and
the regions between end of OPTEE and RAM top are set as cacheable, if
any actually exist.
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
My old mail address, ziyao@disroot.org, has stopped working. Switch to
my new address, me@ziyao.cc, and map it in .mailmap.
Signed-off-by: Yao Zi <me@ziyao.cc>
With LTO enabled, mini U-Boot was hanging during reloc_fdt().
The initial stack pointer was placed too low, and the FDT memcpy
destination was carved only 4KB above it. This left insufficient
margin, causing the FDT copy to overwrite the live early stack
and corrupt execution before relocation.
To fix this, increase the malloc heap from 8KB to 12KB and raise the
initial stack pointer by 4KB. Together these adjustments increase
the separation between the early stack and the FDT region during
the pre-relocation phase, eliminating the overlap and fixing the
hang on mini builds (QSPI/OSPI).
Signed-off-by: Pranav Tilak <pranav.vinaytilak@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
The GitHub dependabot tool has reported two "high" priority bugs,
CVE-2025-66418 and CVE-2025-66471, with this package. Update to the
patched version.
Reported-by: GitHub dependabot
Acked-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
While adding CPSW device support to enable Ethernet boot for J722S,
dev-data and clk-data for eMMC was removed by mistake, which leads to eMMC
boot failure. Update the dev-data and clk-data to fix that.
Fixes: a02009f3a8 ("arm: mach-k3: j722s: Update SoC autogenerated data to enable Ethernet boot")
Reported-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
Tested-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
ARM GCC tool check is not up to date,
while issues are reported such as file truncated linker errors.
Using ARM official cross tools shows that 10.0.1 is a safe
version to support latest kbuild bump properly.
Signed-off-by: Brian Sune <briansune@gmail.com>
I am moving over to using my email address at kernel.org.
Change this in all the affected MAINTAINERS files.
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Pull request efi-2026-01-rc4
CI: https://source.denx.de/u-boot/custodians/u-boot-efi/-/pipelines/28652
Documentation:
* Correct and add missing pytest hook script environment variable names
* board: verdin-am62p: Fix boot log output
* Add a page for downloading the U-Boot logo with and without text
UEFI:
* Fix a memory leak when retrieving device paths from boot vars
Fix boot log output not being rendered correctly, fix
it doing the same as done in verdin-am62.rst.
Fixes: b8c43968b8 ("board: toradex: add verdin am62p support")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
get_dp_device() is used to derive the device path from a boot variable.
However, if the last efi_get_variable_int() call fails, we return an
error without freeing 'buf'.
There's no need to call efi_get_variable_int() for variables we don't
know the size since we have the efi_get_var() wrapper.
Replace that in the two instances we use it. The first one will also
fix the memory leak.
A nice sideeffect is that the code size is also reduced, since we are
re-using functions instead of open coding them
$~ bloat-o-meter u-boot u-boot.new
add/remove: 0/0 grow/shrink: 1/2 up/down: 6/-196 (-190)
Function old new delta
version_string 70 76 +6
efi_launch_capsules 2288 2196 -92
get_dp_device 244 140 -104
Total: Before=1222331, After=1222141, chg -0.02%
Fixes: c74cd8bd08 ("efi_loader: capsule: add capsule_on_disk support")
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Add the _EXTRA variants of U_BOOT_BUILD_DIR and U_BOOT_RESULT_DIR to the
list of environment variables set for hook scripts.
These were added in commit 8f2a9fa7d6 ("test: Support testing with two
board-builds") but were not documented.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Fix the names of environment variables set for hook scripts. These
have a U_BOOT_ prefix, not UBOOT_.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Unfortunately I don't really have time to review clock patches. When I
initially started maintaining this subsystem I had more free time than I do
now. But I also found it hard to motivate myself to review patches. Many
clock patches add support for new SoCs and they are time consuming to
review properly. You effectively have to spend a few hours reading the
reference manual (if it's public!) and reviewing drivers is no small feat
either. This is made more difficult since clocking is often very different
between SoCs and it can be difficult to determine whether something is a
bug in the driver or a workaround for some hardware behavior. I mostly
don't care about any given SoC unless I'm hacking on it so I ended up with
a ton (more than 7000) of unreviewed patches piling up in my inbox. I'd
love to be more active, but I have a day job and I usually want to work on
something more interesting when I get home. I still think the clock
subsystem is a major mess but I don't care enough to fix it :l
The subsystem itself should probably get orphaned since AFAICT all patches
go through the mach/arch maintainer or to Tom.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
When I modified this code I meant to accept the LGPL offer to convert the
license to GPL. However, while there is an LGPL 2.1, the next version of
the GPL after 2.0 is 3.0. Fix the license version
Fixess: c4ac52f55d ("test: Add test for strlcat")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Python 3.7 and 3.8 lack the files attribute in importlib.resources.
Use importlib_resources to fix build errors with Python 3.8:
binman: module 'importlib.resources' has no attribute 'files'
Fixes: 538719cb6a ("binman: migrate from pkg_resources to importlib")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Acked-by: Quentin Schulz <quentin.schulz@cherry.de>
[trini: Re-add # pragma: no cover line]
Signed-off-by: Tom Rini <trini@konsulko.com>
The MAINTAINERS files for B&R boards are not in sync
with the current file names. Update the files so
that they are correct again.
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
B&R Industrial Automation has been acquired by ABB in 2017, and this
will be reflected in our email addresses beginning from December 2025.
The email addresses change as follows:
@br-automation.com -> @<country-code>.abb.com
The existing email addresses will be valid until December 2026.
Add entries for Bernhard Messerklinger and myself to .mailmap, and
update the MAINTAINERS files.
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@at.abb.com>
This is R-Car X5H support. It was originally posted before rc1 and the
changes are well isolated. This is the final patchset which enables the
Gen5 drivers that are already in tree. I waited with this a bit until
the SCMI ID discussion stabilized and TFA X5H support landed. So now, I
can add the final piece into U-Boot too.
Note that this is still very much experimental, the X5H upstreaming is
in very early stages. The OF_UPSTREAM conversion will happen likely in
2026.04 or 2026.07 window, depending on when the Linux DTs land. The
compound-clock.c is surely going to go away once SCP gets updated and
the MFIS mailbox will be reworked once upstream bindings get developed.
This also includes SH DT alignment fix.
Extend the stub PSCI implementation with support for R-Car Gen5.
R-Car Gen5 uses different register to perform reset, therefore
add a compile-time conditional. This is __secure code, therefore
the runtime SoC detection parts are not available to it, hence
the compile time conditional.
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> # Tweak commit message
Add initial support for Renesas R-Car X5H R8A78000 Ironhide board.
This consists mainly of DTs, Makefile and Kconfig entries and board
specific configuration files.
The DTs will be gradually switched over to Linux DTs via OF_UPSTREAM
once Linux DTs become available upstream, as upstreaming progresses.
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add initial device trees for Renesas R-Car X5H R8A78000 SoC.
Include very basic clock, reset, power domain headers which
are used to control supported peripherals via SCMI / SCP. The
headers are currently kept limited to avoid possible ABI break.
A lot of clock are still stubbed via fixed-clock, this is going
to be gradually removed over time, as more of the platform is
upstreamed.
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Khanh Le <khanh.le.xr@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add initial changes to support Renesas R-Car Gen5 SoC.
Introduce Kconfig entries, architecture headers and PRR IDs for Renesas
R-Car Gen5 and R-Car X5H R8A78000 SoC. Add Makefile change to produce
u-boot-elf.srec with correct offset for installation tooling. Update
MAINTAINERS entry to cover both r8a77nnn and r8a78nnn .
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add support for the Renesas MFIS mailbox, which provides an interface
between the different CPU Cores, such as AP System Core domain and the
Realtime Core domain, SCP Core domain and AP System Core domain or
Realtime Core domain and AP System Core domain or Realtime Core domain.
Signed-off-by: Tuyen Dang <tuyen.dang.xa@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> # Update the driver
[Marek: Rename the driver to renesas-mfis, simplify the driver.
Always use only one TX channel and no RX channel, drop all
unnecessary code. Perform 1ms delay in send callback which
is perfectly fine to do in U-Boot which does RX polling]
The current state of SCP on Renesas R-Car Gen5 is not yet final and
is still missing full clock control, the clock control is exposed as
separate enable/disable and rate controls.
Temporarily introduce custom local compound clock, which are used as
an adaptation layer between U-Boot clock tree and current state of
SCP, and which bind two SCP clock into a single compound clock, which
provides both enable/disable and rate controls.
This is mainly meant to be used by SD/eMMC controller, to allow the
driver to both turn its clock on and off, and also obtain the current
clock rate. This is going to be removed once the SCP clock protocol
solidifies.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Make sure the end of U-Boot is at 8-byte aligned offset, not 4-byte
aligned offset. This allows safely appending DT at the end of U-Boot
with the guarantee that the DT will be at 8-byte aligned offset. This
8-byte alignment is now checked by newer libfdt 1.7.2 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The Linux kernel can discover SMBIOS tables through two primary methods:
1. Via EFI tables, when using EFI boot;
2. Via the 'smbios3-entrypoint' property in the /chosen node of the
device tree.
When U-Boot boots a Linux kernel using a non-EFI command ("bootm",
"bootz", or "booti"), the kernel relies on the device tree to detect
the hardware. If SMBIOS tables are available in U-Boot, they should
be passed to the kernel via this device tree property.
This patch modifies boot_fdt_prepare(), to inject the SMBIOSv3 table
address into the device tree if there is a table generated by U-boot.
The "board_fdt_chosen_smbios" is weak in order to leave the possibilty
for specific boards to select custom SMBIOS addresses.
The changes in this patch are added in the context of supporting this
device tree property in linux kernel:
https://lkml.org/lkml/2025/10/24/1393
Device tree schema was updated to include the "smbios3-entrypoint" node
in pull request: https://github.com/devicetree-org/dt-schema/pull/177
Signed-off-by: Adriana Nicolae <adriana@arista.com>
The redundant environment offset is already set in board configuration,
but the redundant environment itself is not explicitly enabled. Make
sure the redundant environment is enabled, as we most certainly do want
to have two copies of the environment.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The CONFIG_ENV_OVERWRITE allows easy rewrite of environment variables
like 'ethaddr' and 'serial#' without any protection against accidental
removal of those variables. Remove this setting to add extra layer of
protection to those variables. The variables can still be overridden
using 'env set -f' (force set) if really needed.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Document the image preparation and flashing techniques for
Exynos7870-based boards. This is done in a separate file in a
sub-directory, which is linked back to the main documentation.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add basic support for the Exynos7870 SoC, this includes device tree
match logic using multiple boards, where devices use a stub dtb in
Samsung's QCDT format. S-BOOT, the previous stage bootloader, places its
cmdline arguments there, which has identifying information.
This is added with support for three devices:
* Samsung Galaxy A2 Core (codename: a2corelte)
* Samsung Galaxy J6 (codename: j6lte)
* Samsung Galaxy J7 Prime (codename: on7xelte)
Add their device trees in the defconfig, and also enable the clock and
pin controller drivers.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add support for a generic platform which intends to support multiple
boards powered by ARMv8 Samsung Exynos SoCs. Some important features
include:
* Fastboot: This is present to provide an open alternative to Samsung's
proprietary Odin protocol. The board file configures certain features
for fastboot, such as a dynamically allocated fastboot buffer, and
standardized (lowercase) partition aliases.
* EFI: Kernel image can be loaded from an EFI partition. This
adopts a standard booting process, which multiple OS distributions
can rely on.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This pull request delivers a broad set of improvements across the
SoCFPGA family, including Agilex5, Cyclone V, SoC64, and common code.
Key updates include refined boot flows, new driver enablement, handoff
tooling enhancements, and several stability fixes.
Highlights:
* Agilex5:
- Enable FAT-based environment storage
- MMC driver restores legacy clkmgr-based clock lookup
- Cleanup of MMC raw mode enablement logic
* Cyclone V:
- SPL FAT boot support and updated bootcmd sequence
- Disable SPL SPI to prevent contention with FAT-based boot
- New board handoff script and BSP generator tooling
- Optimized Makefile support for SoCFPGA handoff workflows* New drivers:
- Cadence xSPI driver with full protocol and command support
- SPL enablement for DW APB GPIO controller
* Networking:
- xgmac MDIO now supports Clause 45 read/write operations
* NAND / SoC64:
- Enable ONFI detection in Denali NAND controller for SoC64 devices
* DTS and board updates:
- Sync common SoCFPGA U-Boot DTS with kernel sources
- Fixes for FPGA2SDRAM configuration and SoCFPGA boot stall behavior
- Vining_FPGA migrated to the modern LED framework
- Device tree relocation no longer forced off for Vining FPGA
* Tooling:
- Introduces a new Python-based Cyclone V BSP generator
covering EMIF, IOCSR, HPS, XML parsing, rendering, and documentation
to simplify board enablement and handoff regeneration workflows
Overall, this series improves boot robustness, enhances xSPI and MDIO
capabilities, modernizes board support, and introduces new tooling to
streamline SoCFPGA handoff generation.
Pipelines test passing
https://source.denx.de/u-boot/custodians/u-boot-socfpga/-/pipelines/28569
The problem we face currently with Azure jobs is that we're running out
of disk space on the runners as we build. There's not a good way to
split approximately 1500 configurations across 10 jobs and not be close
to or exceeding that limit. Split this in to 29 jobs instead with a goal
of averaging an hour per job. This split gets us close, but there are
still some challenging jobs to try and break up further. The list is
mostly alphabetized but with some intentional changes (catch-all are
last, mx/imx are together, SoC family splits are just grouped together).
The average build time should be close to the same, but outliers can and
will happen.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Introduce socfpga_g5_handoff_prepare target in U-Boot
arch/arm/mach-socfpga/config.mk
- Users can convert the handoff via make prepare.
- Detects Altera/Intel SoCFPGA boards from .config
- Combines vendor/board extraction into a single shell call
- Checks for hps_isw_handoff folder and .hiof files
- Uses ls -d instead of find for faster folder detection
- Runs BSP generator script only if files exist
- Non-blocking: continues if handoff folder or files are missing
- HANDOFF_PATH user define allows overriding auto-detected folder
- Minimizes subshells and other slow constructs for faster CI
Signed-off-by: Brian Sune <briansune@gmail.com>
bcm54210e_config() configures the RGMII delays and then calls
bcm5461_config(). But the latter will do a PHY soft reset and thus
resets the delay settings again. Call bcm5461_config() first to fix it.
Fixes: cba79a1b2e ("net: phy: broadcom: add support for BCM54210E")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Rafał Miłecki <rafal@milecki.pl>
According to the TI DP83869HM datasheet Revision D (June 2025), section
7.6.1.41 STRAP_STS Register, the STRAP_OPMODE bitmask is bit [11:9].
Fix this.
In case the PHY is auto-detected via PHY ID registers, or not described
in DT, or, in case the PHY is described in DT but the optional DT property
"ti,op-mode" is not present, then the driver reads out the PHY functional
mode (RGMII, SGMII, ...) from hardware straps.
Currently, all upstream users of this PHY specify both DT compatible string
"ethernet-phy-id2000.a0f1" and ti,op-mode = <DP83869_RGMII_COPPER_ETHERNET>
property, therefore it seems no upstream users are affected by this bug.
The driver currently interprets bits [2:0] of STRAP_STS register as PHY
functional mode. Those bits are controlled by ANEG_DIS, ANEGSEL_0 straps
and an always-zero reserved bit. Systems that use RGMII-to-Copper functional
mode are unlikely to disable auto-negotiation via ANEG_DIS strap, or change
auto-negotiation behavior via ANEGSEL_0 strap. Therefore, even with this bug
in place, the STRAP_STS register content is likely going to be interpreted
by the driver as RGMII-to-Copper mode.
However, for a system with PHY functional mode strapping set to other mode
than RGMII-to-Copper, the driver is likely to misinterpret the strapping
as RGMII-to-Copper and misconfigure the PHY.
For example, on a system with SGMII-to-Copper strapping, the STRAP_STS
register reads as 0x0c20, but the PHY ends up being configured for
incompatible RGMII-to-Copper mode.
Fixes: f3e22eea81 ("net: phy: add TI DP83869HM ethernet driver")
Signed-off-by: Thanh Quan <thanh.quan.xn@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> # Use FIELD_GET()
Disable support for using SPI in SPL to solve Cyclone V storage issue as
the OCRAM is only 64kb. The SPI configurations are only
required during uboot proper only.
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
Enable support for FAT filesystem with SPL for CycloneV instead of raw
mode.
Recent changes breaks CycloneV MMC boot from raw mode, and so we are taking
this opportunity to migrate MMC boot mode to FAT as smaller OCRAM size is
required, as well as aligning MMC boot flow with our other devices.
Fixes: 2a00d73d08 ("spl: mmc: Try to clean up raw-mode options")
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
We no longer use raw mode to boot from MMC for our devices in favor
of FAT filesystem.
Maintaining this config for legacy gen5 devices as to not risk breaking
any configurations still utilizing raw mode.
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
Restore legacy implementation of retrieving clkmgr base address from
mach-socfpga/misc.c driver for our legacy devices.
Excluding Agilex7/7M from this implementation as these devices' clock
driver is already following clock driver model and is supporting
enable/disable APIs.
The legacy devices' clock driver will have to be refactored to support
driver model which enables us to support enable/disable APIs for these
devices.
Fixes: ab27182cac ("mmc: socfpga_dw_mmc: Enable/disable SDMMC clock via API")
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
mkeficapsule tool will be built by default if EFI_LOADER is set due to
commit b7a625b1ce ("tools: Build mkeficapsule tool by default if
EFI_LOADER is set").
This will cause compilation error on all our SoCFPGA devices, hence we will
be disabling this config as we do not utilize this tool.
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
This migrates from the legacy LED API to use the modern LED framework
which makes use of the FDT.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Acked-by: Tien Fong Chee <tien.fong.chee@altera.com>
Remove setting of fdt_high to ~0, which disables device tree relocation,
from the default environment. Doing so prevents U-Boot from correcting
problems such as having an unaligned device tree and leads to various
failure modes in the OS.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marek.vasut@mailbox.org>
Since U-Boot 2025.07 pure SD Card
boot no longer works. Now Altera released 2025.07
shows the different on the u-boot files.
After testing, the major root case is
get_managers_addr. And this patch fix the
SD boot stall via pulling from offical.
Signed-off-by: Brian Sune <briansune@gmail.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
The dtsi for socfpga common should
turn on L2 and memory and no reason not
to do so
Signed-off-by: Brian Sune <briansune@gmail.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
Enable ONFI parameter page detection for SoCFPGA SoC64 devices by
selecting SYS_NAND_ONFI_DETECTION in the NAND_DENALI Kconfig entry.
This allows SoCFPGA SoC64 platforms using the Denali NAND controller
to automatically detect NAND parameters via the ONFI interface instead
of relying on hardcoded configuration values.
The selection is limited to TARGET_SOCFPGA_SOC64 to avoid affecting
non-SoC64 platforms that use legacy NAND handling.
Signed-off-by: Dinesh Maniyam <dinesh.maniyam@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
Since turning from old build flow.
New Altera SoCFPGA requires converting handsoff
conversion via the python script. This is from
official provided, and now sync to U-Boot with
better location at tools/cv_xxxx. Meantime,
requirement.txt is also provided to further
explain the libraries require for these scripts.
Signed-off-by: Brian Sune <briansune@gmail.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
This patch ports the Cadence xSPI controller driver from
the Linux kernel. The controller supports three operating modes:
1. ACMD (Auto Command) mode
- Includes PIO and CDMA submodes.
- CDMA mode uses linked descriptors for high-performance,
low-overhead operation.
- PIO mode is suitable for simple, single-command transactions.
2. STIG (Software Triggered Instruction Generator) mode
- Issues low-level 128-bit instructions to memory.
- Uses the Slave DMA interface for data transfers.
3. Direct mode
- Enables direct data access through the slave interface
without commands.
Currently, only the STIG work mode is enabled. Additional modes will be
supported in future updates.
At the same time, also enabling the kconfig option for xSPI driver.
This driver has been ported and functionally verified on the Intel Simics
platform. It is intended for evaluation and experimental use at this stage.
Link: https://lore.kernel.org/all/1632038734-23999-1-git-send-email-pthombar@cadence.com/
Signed-off-by: Boon Khai Ng <boon.khai.ng@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
Enable storing the U-Boot environment in a FAT filesystem for Agilex5.
This allows the board to read and write environment variables from the
first partition of the first device formatted with FAT, in addition to the
existing UBI-based environment configuration.
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
After testing, w/o proper setup
the FPGA2SDRAM bridge will not work and stall.
Pulling from official fix and w/o this initialization,
both 2025.07 and 2025.10 also suffer stall on U-Boot
and distro. Any FPGA to HPS-SDRAM action will immediate
stall the CPU. As such, this patch fix the issue.
Signed-off-by: Brian Sune <briansune@gmail.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
Add SPL_DWAPB_GPIO configuration option to enable the Designware APB
GPIO driver in SPL builds.
Changes:
- Add SPL_DWAPB_GPIO Kconfig option with SPL_DM_GPIO dependency
- Update Makefile to use CONFIG_$(PHASE_)DWAPB_GPIO pattern for
conditional compilation in both SPL and main U-Boot builds
Signed-off-by: Tanmay Kathpalia <tanmay.kathpalia@altera.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Updates for RPi for 2026.01-rc4:
- rpi: Fix DRAM size reporting to show total RAM
- rpi: Use the U-Boot control FDT for fdt_addr
- pinctrl: bcm283x: Add GPIO pull-up/down control for BCM2835 and BCM2711
- rpi: Fix compilation with larger configs
The VideoCore mailbox GET_ARM_MEMORY only reports the size of the
first accessible memory region (~947 MiB on RPi4 with 8GB), not the
total RAM. This causes U-Boot to display "DRAM: 947 MiB (total 7.9 GiB)"
instead of "DRAM: 7.9 GiB".
On Raspberry Pi 4 with 8GB RAM, the memory is split across multiple
non-contiguous banks. The dram_init() function only sets gd->ram_size
to the first bank size reported by the VideoCore firmware, while
fdtdec_setup_memory_banksize() correctly populates all memory banks
from the device tree.
Fix this by updating gd->ram_size after dram_init_banksize() has
populated all memory banks, so it reflects the actual total RAM
across all banks.
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
We should avoid overwhelming users with non-essential messages.
'Register NbrPorts' is a debug message for EHCI. Do the same for XHCI.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Marek Vasut <marek.vasut@mailbox.org>
The SPL_STACK config option now depends on having SPL_HAVE_INIT_STACK
defined. This made savedefconfig dropping SPL_STACK when sending the
initial configuration.
Note that SPL/U-Boot are able to boot linux from mass storage with
SPL_STACK not set but other use cases might run out of stack or
overlap with other RAM use.
Compare with:
commit d6a53f523a ("spl: Add an SPL_HAVE_INIT_STACK option")
commit 25fefa05d7 ("configs: Resync with savedefconfig")
Fixes: ff0540fcfe ("board: toradex: add Toradex SMARC iMX95")
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Partitions can be become unusable due to power cuts or failed updates.
Use the bootmeth RAUC if partitions for at least one slot exist. The
bootmeth can then select the working slot.
Signed-off-by: Leonard Anderweit <l.anderweit@phytec.de>
Tested-by: Martin Schwan <m.schwan@phytec.de>
Only check if the root partition exists when scanning for the slots
partitions and not if the filesystem can be accessed. It is not needed
to access the filesystem of the root partition as it might not be
supported by u-boot or be encrypted.
Signed-off-by: Leonard Anderweit <l.anderweit@phytec.de>
Tested-by: Martin Schwan <m.schwan@phytec.de>
The nfsroot constructed as part of the default Analog Devices boot
strategy is missing a semicolon between the server ip and the root path
itself. This adds the missing semicolon.
Signed-off-by: Greg Malysa <malysagreg@gmail.com>
This patch fixes a boot failure on the AM64x EVM that was introduced when the do_board_detect function was removed during a refactoring.
It restores the do_board_detect function for the AM64x, AM62x, and AM65x boards to ensure the common board detection logic is executed correctly.
Fixes: 804b80288a ("board: am65x: Use generic AM6x board detection function")
Fixes: ce56e553c3 ("board: am64x: Use generic AM6x board detection functions")
Fixes: ff1b83c095 ("board: am62x: Add support for reading eeprom data")
Signed-off-by: Guillaume La Roque (TI.com) <glaroque@baylibre.com>
Currently, the bind callback of the driver namely am65_cpsw_nuss_bind()
registers all ethernet ports including the ones that have been disabled
in the device-tree. Since the ports that have been disabled are ought to
be ignored, fix the implementation to register only the enabled ports as
indicated by their 'status' in their respective device-tree node.
Fixes: 3943531a54 ("net: ti: am65-cpsw-nuss: Define bind method for CPSW driver")
Reported-by: Wadim Egorov <w.egorov@phytec.de>
Closes: https://patch.msgid.link/8b4ac072-125c-493b-b12a-f0a4e9d56e7e@phytec.de
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
The helper function "ti_pd_get()" is responsible for powering on a
domain if it is powered off. In the current implementation, if a power
domain is determined to be powered off - no prior users and the PDCTL
register indicates that the user desired state is OFF, then powering on
the domain constitutes setting 'PDCTL_STATE_ON' field of the PDCTL
register.
While the current implementation indeed requests the power domain to be
transition to the ON state, the helper function "ti_pd_get()" doesn't
verify that the power domain has 'transitioned' to the ON state before
returning to its caller. As a result, it is possible that the device(s)
belonging to the power domain may be accessed before it is truly powered
on, leading to a bus abort.
Fix this by waiting for the power domain to transition to the ON state
by using "ti_pd_wait()" before returning from "ti_pd_get()".
Fixes: 144464bd2c ("power: domain: Introduce driver for raw TI K3 PDs")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Tested-by: Hrushikesh Salunke <h-salunke@ti.com>
extension_get_list() will return NULL if there is no extension device.
Check for this situation.
Addresses-Coverity-ID: 638557 - Null pointer dereferences (NULL_RETURNS)
Fixes: 2d12958ee7 ("boot: Remove legacy extension board support")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Acked-by: Kory Maincent <kory.maincent@bootlin.com>
- Move to jammy-20251013 tag
- Bring in tkinter so that FATtools should run and more tests should be
run.
- Update to QEMU 10.0.6
- Pick tags for (most of) trace-cmd
Signed-off-by: Tom Rini <trini@konsulko.com>
We have not been picking a tag for the trace-cmd build process.
Currently the tip of libtraceevent fails to build. Address both problems
here by picking recent stable tags for libtraceevent and libtracefs
(trace-cmd has no recent tags). Further, as it is often reported that
this fails to build due to a race, stop using "make -j$(nproc)" as this
is also small enough of a set of builds to not be an issue.
Signed-off-by: Tom Rini <trini@konsulko.com>
In some cases our tests for exFAT don't run because we fail to be able
to create the underlying image. This is in turn because while creation
of the image succeeds, it seems that some way of how we invoke FATtools
wants to import tkinter, that fails and so the test stops there. Having
tkinter available (and then presumably a fallback to non-GUI because
it's not available) leads to the tests running as expected.
Reviewed-by: Marek Vasut <marek.vasut@mailbox.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
The QEMU project has the 10.0.x series as an LTS release. While we are
not doing an LTS ourselves, we can be confident in the changes between
10.0.2 and 10.0.6, so update ourselves.
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove setting of fdt_high to ~0, which disables device tree relocation,
from the default environment. Doing so prevents U-Boot from correcting
problems such as having an unaligned device tree and leads to various
failure modes in the OS.
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Doing USB boot on E850-96 is most useful in two cases:
1. For unbricking the board
2. During the bootloader development
In both cases a U-Boot binary is being re-flashed to eMMC. The most
convenient way to update U-Boot in eMMC is by using DFU. Implement
entering DFU flashing mode automatically when U-Boot is executed on USB
boot. That makes it easier for users to re-flash U-Boot without even
having serial console running, e.g.:
$ ./smdk-usbdl
$ dfu-util -D u-boot.bin -a bootloader
See [1,2] for details.
Entering DFU mode is implemented by setting corresponding environment
variables:
bootcmd="dfu 0 mmc 0"
bootdelay=0
Do not save the U-Boot environment though, to avoid falling through to
DFU mode on a regular eMMC boot.
[1] doc/board/samsung/e850-96.rst
[2] https://gitlab.com/LinaroLtd/e850-96/tools/dltool/-/tree/uboot
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
During USB boot it's expected that the bootloader (U-Boot) should
download LDFW and TZSW firmware binaries over USB, using corresponding
SMC call. Once it's done, the Boot ROM code can release the USB block,
so that it can be used in U-Boot (e.g. for flashing images to eMMC using
DFU or fastboot). Otherwise USB wouldn't be accessible in U-Boot, and
any attempt to access USB PHY or DWC3 registers will lead to abort.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
During USB boot U-Boot is supposed to download some firmware over USB.
It's done by EL3 software, so it has to be requested via corresponding
SMC call. Implement a routine for doing that.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The LDFW firmware loading is done in two steps:
1. Read the firmware binary from some block device
2. Provide it to EL3 monitor software via an SMC call, so it can copy
it to a Secure World memory and start using it
Let's split the load_ldfw() function by two functions correspondingly,
to reflect that process better:
- load_ldfw_from_blk()
- init_ldfw()
It can be useful in case when the LDFW binary should be obtained from
some different media, e.g. downloaded over USB during USB boot.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Implement functionality to check the current boot device (a device where
the SoC ROM code is loading the bootloaders from). The boot device order
can be changed using the SW1 DIP switch on the E850-96 board (which
controls XOM SoC lines), as stated in [1].
The boot device information is requested from EL3 software using the
corresponding SMC call, which in turn reads it from iRAM memory, which
was written by the ROM code. New routines decode that data and allow the
user to check the current boot device, boot order, etc. That API can be
used further to implement different code flows depending on the current
boot device, e.g.:
- on eMMC boot: obtain the firmware binaries from eMMC
- on USB boot: download the firmware over USB instead
No functional change; this patch only adds new functionality but it's
not used yet.
[1] doc/board/samsung/e850-96.rst
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Move DRAM init functions close to other public functions, to make things
visually distinct and improve the readability.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
mu@27020000 is required for communication with ELE firmware, and
lpuart5 is the standard output device. Both peripherals must be
available before U-Boot relocation. Use bootph-all instead of
bootph-pre-ram so these nodes are retained across all boot phases.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
In TEZI (Toradex Easy Installer), we use one U-Boot binary for both our
NAND and eMMC Colibri iMX7 modules. Currently, CONFIG_PREBOOT sets the
environment variable 'fdtfile' depending on which defconfig was used,
adding the '-emmc' variant for the emmc defconfig. Since we always build
the TEZI recovery U-Boot with the standard (non-emmc) defconfig, fdtfile
has to be overwritten later or it will be wrong there.
By using '$variant', the fdtfile var is properly constructed at run time
for both the NAND and eMMC variants, and we do not have to worry about
setting fdtfile again when building the recovery TEZI U-Boot.
This also synchronizes these configs with how we handle the iMX6ULL.
Fixes: 327381e8b5 ("colibri_imx7: use preboot for fdtfile evaluation")
Signed-off-by: Ernest Van Hoecke <ernest.vanhoecke@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Fix macros for the GPIO function for two pads (ENET1_TD3 and I2C2_SCL),
aligning them to the functions specified in the datasheet.
Fixes: a9d562daa3 ("imx: Add iMX91 support")
Suggested-by: Javier Viguera <javier.viguera@digi.com>
Signed-off-by: Francesco Valla <francesco@valla.it>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
There is a condition guard which ensures that the GPIO node, indeed
describes a GPIO controller.
if (!fdtdec_get_bool(blob, node, "gpio-controller"))
continue;
Since the bank base is being incremented in the loop, it is done so
irrespective of whether the node is a GPIO controller or not. This leads
to the incorrect resolution of bank base addresses.
Move it out of the loop, and instead increment the bank base address
only if the driver successfully binds a GPIO controller.
Reviewed-by: Henrik Grimler <henrik@grimler.se>
Fixes: b8809e60cd ("dm: exynos: gpio: Convert to driver model")
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The fdt_addr variable is used in extlinux as a fallback devicetree if
none is provided by the boot command. Otherwise the only use in U-Boot
seems to me efi_install_fdt() when the internal FDT is required.
The existing mechanism uses the devicetree provided to U-Boot, but in
its original, unrelocated position. In my testing on an rpi_4, this ends
up at 2b35ef00 which is not a convenient place in memory, if the ramdisk
is large.
U-Boot already deals with this sort of problem by relocating the FDT
to a safe address.
So use the control-FDT address instead.
Remove the existing comment, which is confusing, since the FDT is not
actually passed unmodified to the kernel: U-Boot adds various things
using its FDT-fixup mechanism.
Note that board_get_usable_ram_top() reduces the RAM top for boards with
less RAM. This behaviour is left unchanged as there is no other
mechanism for U-Boot to handle this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Christopher Obbard <christopher.obbard@linaro.org>
Tested-by: Christopher Obbard <christopher.obbard@linaro.org> # CM4 1G
This patch adds support for configuring GPIO pull-up and pull-down
resistors in the BCM283x pinctrl driver. It implements the brcm,pull
device tree property to control pin bias settings.
The implementation follows the hardware-specific pull control
mechanisms:
- BCM2835: two-step GPPUD register sequence
- BCM2711: direct per-pin control registers
This enables device tree configurations to specify pull-up, pull-down,
or no bias for individual GPIO pins.
Tested on Raspberry Pi boards with both BCM2835 and BCM2711 SoCs.
Signed-off-by: Cibil Pankiras <cibil.pankiras@egym.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Tom reports that adding more Kconfig options fails with
board/raspberrypi/rpi/lowlevel_init.o: in function `save_boot_params':
board/raspberrypi/rpi/lowlevel_init.S:20:(.text+0x0):
relocation truncated to fit: R_AARCH64_ADR_PREL_LO21
against symbol `fw_dtb_pointer' defined in .data section
in board/raspberrypi/rpi/rpi.o
make: *** [Makefile:2029: u-boot] Error 1
Since fw_dtb_pointer lives in .data it might end up above the
+-1MB that adr can reach.
So switch over to adrp+add which has a +-4gb reach.
Reported-by: Tom Rini <trini@konsulko.com>
Closes: https://source.denx.de/u-boot/custodians/u-boot-raspberrypi/-/issues/2
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
The SCMI shared memory area is no longer automatically marked as
non-cacheable after the commit a5a0134570 ("firmware: scmi: Drop
mmu_set_region_dcache_behaviour() misuse").
This change in behavior cause Rockchip RK3588 boards to fail boot with:
SoC: RK3588
DRAM: 8 GiB
scmi-over-smccc scmi: Channel unexpectedly busy
scmi_base_drv scmi-base.0: getting protocol version failed
scmi-over-smccc scmi: failed to probe base protocol
initcall_run_r(): initcall initr_dm() failed
### ERROR ### Please RESET the board ###
Update the memory mapping on RK3588 to mark the SCMI shared memory area
as non-cacheable to fix the SCMI shared memory based transport issue
that prevented RK3588 boards from booting.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Fix two memory allocation bugs in label_boot_extension():
1. When label->fdtdir is not set, overlay_dir was used without any
memory allocation.
2. When label->fdtdir is set, the allocation size was incorrect,
using 'len' (just the fdtdir length) instead of 'dir_len' (which
includes the trailing slash and null terminator).
Resolve both issues by moving the memory allocation and string
formatting outside the conditional block, resulting in clearer code
flow and correct sizing in all cases.
Closes: https://lists.denx.de/pipermail/u-boot/2025-November/602892.html
Addresses-Coverity-ID: 638558 Memory - illegal accesses (UNINIT)
Fixes: 935109cd9e ("boot: pxe_utils: Add extension board devicetree overlay support")
Signed-off-by: Kory Maincent (TI.com) <kory.maincent@bootlin.com>
Tested-by: Surkov Kirill <fanra3.tk@gmail.com>
Size of array buf was incorrect due to sizeof returning the
size of an integer (typically 32 bits) instead of a u64 type
(64 bits). Hence, buf array was shorter than expected.
Signed-off-by: Francois Berder <fberder@outlook.fr>
Reviewed-by: Simon Glass <sjg@chromium.org>
Pull request efi-2026-01-rc3-2
CIL https://source.denx.de/u-boot/custodians/u-boot-efi/-/pipelines/28454
Documentation:
* board: ti: am6254atl_sk: correct value of PRELOADED_BL33_BASE
* pytest: fix u-boot-test-flash typo
* samsung: Fix PXE description for the E850-96 board
* board: ti: k3: Update TI firmware repository URL to GitHub
* add missing macro descriptions to include/test/ut.h and add it to
the API documenation
* rearrange the description of DM tests and describe return values
Testing:
* Enable CI testing ACPI on qemu-riscv64_smode_acpi_defconfig
* Add qemu-riscv64_smode_defconfig to the CI tests
* Generalize tests such that they can run on RISC-V QEMU
- fdt_test_apply requires CONFIG_OF_LIBFDT_OVERLAY
- cmd/fdt: do not assume RNG device exists
- cmd/bdinfo: make no flash assumption
- cmd/bdinfo: consider arch_print_bdinfo() output
- common/print: do not use fixed buffer addresses
- cmd/fdt: do not use fixed buffer addresses
- raise CONFIG_CONSOLE_RECORD_OUT_SIZE default to 0x6000
* enable CONFIG_CONSOLE_RECORD=y on qemu-riscv64_smode_acpi
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEbcT5xx8ppvoGt20zxIHbvCwFGsQFAmkg1IsACgkQxIHbvCwF
# GsQVLA//dmiApob+J9FUhD8joD+DaKSNfLYmv8zwfIFL2xRxx7D+CQT+r+I9FJYI
# KojiLyn4PE/5VOm+wrsvAoYoMLJwAHvg5nmYJLLzvm6V//DLd1AEopP/+Uh8gEVW
# xYGLcvDyGgZpraAhcmqRnAS89py3SigwGzhcUMbT6ZC6pgMVEsBpg8XeMpY7N05c
# rwyqFAAPD8RcF7veQCpry87NiK5o+9YuM1zKl5sDFOpEWKq5ToNwhQ00bnux9lUd
# HWz9X6ge58iFiMXRqUCnOaPeXeChn9ejyEiKtfQ0JtykOf9NT2WMdD2VKe9PCYsd
# f7OynJTGG2OXTKBhon/xj75itiTm7EELc/FHwHEdtZIIHgpi/C33yQgKxLf9mtUo
# Z7DKYpPoaTCbJhs9LCK942KPtshbtAJLKTVqyBPo7Jn0mneeCQUsbaQRU7JruJTK
# hKluUjsAry3Do3wv/w6B8R6MMgfpBktPkqjg9e/maSdhYdkNAYpjajtORgpqmJRV
# HTGJXfL3qFC50jlenlMYOm4Qake33MIMzubaxoM3j5ENDUJ7KAbWADEoWDpve8Tu
# b/fX8uuW+g2T18Y/M9Bsk/jaUjDTx0xtZUSYNIIQJFDaJMzUxGYWlmtXhLZwFU8g
# 7S5pBmgxoSAtQSMAeoJPJp9FSgXYqiGLUeSwcOH2NaPn0lLFvK0=
# =D0Yy
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 21 Nov 2025 03:07:23 PM CST
# gpg: using RSA key 6DC4F9C71F29A6FA06B76D33C481DBBC2C051AC4
# gpg: Good signature from "Heinrich Schuchardt <xypron.glpk@gmx.de>" [unknown]
# gpg: aka "[jpeg image of size 1389]" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 6DC4 F9C7 1F29 A6FA 06B7 6D33 C481 DBBC 2C05 1AC4
Fix typo: `s/u-boot-test-flash1/u-boot-test-flash/`. The correct name of
the script doesn't have a "1" in it.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
As stated in PXELINUX doc [1], the PXE configuration file has to be in
the format of "01-MAC-address" for Ethernet connections:
The hardware type (using its ARP "htype" code) and address, all in
lowercase hexadecimal with dash separators. For example, for an
Ethernet (i.e. ARP hardware type "1") with address
"88:99:AA:BB:CC:DD", it would search for the filename
"01-88-99-aa-bb-cc-dd".
Indeed, PXE implementation in U-Boot looks for files like that, as can
be seen from this call chain:
format_mac_pxe()
pxe_mac_path()
pxe_get()
extlinux_pxe_read_bootflow()
Mention the fact that PXE expects the configuration file to be prepended
with "01" in the PXE section of E850-96 documentation. While at it, fix
some other minor issues in PXE section.
[1] https://wiki.syslinux.org/wiki/index.php?title=PXELINUX
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
The SPL_TEXT_BASE for AM62x SiP is set as 0x82000000 whereas the
documentation states 0x81880000 as the PRELOADED_BL33_BASE value.
Both should match to allow TFA to jump to the address where A53 SPL has
been loaded.
Signed-off-by: Anshul Dalal <anshuld@ti.com>
Acked-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Update the TI firmware repository URL from git.ti.com to the
GitHub mirror at github.com/TexasInstruments/ti-linux-firmware
which is much more reliable.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reported-by: Tom Rini <trini@konsulko.com>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
QEMU comes with its own OpenSBI. For running RISC-V virtual machine
using one of qemu-riscv64_smode_defconfig or
qemu-riscv64_smode_acpi_defconfig is the natural choice.
Add the riscv64 smode configurations to the test scope.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
For some tests the current default of 0x400 for
CONFIG_CONSOLE_RECORD_OUT_SIZE is too small.
Raise the value to 0x6000 which is already the most common value.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The location of memory depends on the board. Do not assume memory at fixed
memory locations. Use memalign() instead to allocate a buffer.
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The location of memory depends on the board. Do not assume memory at fixed
memory locations. Use calloc() instead to allocate buffers.
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
On x86 commit 9b35dbc93f ("x86: Show the timestamp counter with bdinfo")
has added another bdinfo output line.
On RISC-V commit 66b5ee9c55 ("riscv: add RISC-V fields to bdinfo
command") implemented arch_print_bdinfo().
Update the bdinfo test accordingly.
Fixes: 9b35dbc93f ("x86: Show the timestamp counter with bdinfo")
Fixes: 66b5ee9c55 ("riscv: add RISC-V fields to bdinfo command")
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
In fdt_test_chosen() currently we test if DM_RNG is configured.
CONFIG_DM_RNG=y does not imply that a RNG device actually exists.
For instance QEMU may be called with -device virtio-rng-device or not.
The current test framework evicts the virtio RNG device even if QEMU is
called with -device virtio-rng-device.
In the fdt_test_chosen() check if a RNG device exists.
Ignore 'No RNG device' messages.
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The `fdt apply` sub-command is only available if CONFIG_OF_LIBFDT_OVERLAY
is enabled.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
"timing" and "timing_res_idx" are unused and not exist in Linux driver,
let's remove them.
Signed-off-by: Zixun LI <admin@hifiphile.com>
Acked-by: Alexander Dahl <ada@thorsis.com>
Reviewed-by: Eugen Hristev <eugen.hristev@linaro.org>
Setup the pmecc data setup time as 3 clock cycles for 133MHz as
recommended by the datasheet.
Backported from Linux: f55f552a7c7e0a1 ("mtd: rawnand: atmel: set pmecc
data setup time")
Fixes: a490e1b7c0 ("nand: atmel: Add pmecc driver")
Signed-off-by: Zixun LI <admin@hifiphile.com>
Tested-by: Alexander Dahl <ada@thorsis.com>
Reviewed-by: Eugen Hristev <eugen.hristev@linaro.org>
CI: https://source.denx.de/u-boot/custodians/u-boot-nand-flash/-/pipelines/28408
This pull request enhances NAND and SPI flash support, primarily
focusing on the Airoha EN7523 platform. The Airoha SPI driver receives
a major update, adding DMA, dual/quad-wire modes, and a critical
workaround to prevent flash damage if the UART_TXD pin shorts to Ground.
New chips supported include FudanMicro FM25S01A SPI-NAND and several
Winbond SPI NOR devices. Fixes include correcting Kconfig dependencies,
updating the mtd benchmark command to use lldiv(), and addressing minor
bugs in the generic spi-mem and SPL NAND code.
The ROM code of Xilinx Zynq searches the boot flash for a "BootROM header"
at increments of 32k (0x8000), beginning with 0x0000 for a
configuration without authentication and beginning with 0x8000
for a configuration with authentication. [1]
Move the offset of the SPL partition on the brcp1 board to 0x8000
so that both cases are the same, e.g. a board that is configured
without authentication can boot an SPL partition with or without
authentication.
[1] Zynq 7000 TRM, section 6.3 "BootROM Code"
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20251029092252.115582-1-wolfgang.wallner@br-automation.com
Use 'Sam Protsenko' as my name consistently in git-shortlog. Also map my
home email address (which I used at some point) to my current work
email.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
The Linaro email address is no longer valid.
See commit 4cad9faf8d ("MAINTAINERS: update my email address")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
I've spent time trying to figure out why my board (Rockchip PX30-based)
suddenly boot loops when running a specific program in Linux userspace
after working on a U-Boot upgrade. I actually inadvertently had the TEE
environment variable set for a device which doesn't actually need to run
any TEE OS (so had OPTEE_LIB disabled).
It is currently possible to build an image with an OP-TEE OS (via the
TEE environment variable) without OPTEE_LIB. U-Boot will happily load
the TEE OS and the next OS (e.g. the Linux kernel).
This is an issue because on FDT-enabled devices, OP-TEE OS adds nodes to
the reserved-memory FDT node for the memory regions it just reserved for
itself. This updated FDT is then passed to U-Boot proper which should
know better not to use memory from there. The actual issue is that
without OPTEE_LIB and OF_LIBFDT enabled, U-Boot proper will not copy
those nodes over to the next OS's FDT before starting it. This results
in the next OS's (e.g. Linux kernel) to not be aware of reserved memory,
incurring random crashes or device reboots when it tries to access
secure reserved memory area.
On Rockchip, the U-Boot FIT image which contains both the TEE OS and
U-Boot proper is generated by binman. Unfortunately, binman doesn't seem
to have access to Kconfig symbols (grep CONFIG_ doesn't return anything
meaningful and binman is either configured through FDT nodes or via CLI
arguments, c.f. cmd_binman in the root Makefile) so we cannot try to be
smart and guide the user to the correct Kconfig option to select if TEE
is set. We could add a property based on the presence of OPTEE_LIB in
rockchip-u-boot.dtsi for example and have a custom message based on
that, the issue is that I assume all FDT-based platforms do actually
need to do this dance, and not only Rockchip.
Another option could be to add a CLI argument to binman through which
we would pass the state of OPTEE_LIB and error out the build in that
case, but that feels like opening the door to other various dirty hacks.
Another option is to propagate the TEE environment variable to the
preprocessor of the FDT (via dtc_cpp_flags) and then we can do
#if defined(TEE) && !IS_ENABLED(CONFIG_OPTEE_LIB)
#error "CONFIG_OPTEE_LIB must be enabled!"
#endif
but we have the same issue as above, it is then Rockchip-specific and
doesn't feel right to me.
Yet another option is to remove the @tee-SEQ node from the binman FIT
description when OPTEE_LIB isn't set but then we would lose the
following nice message when no TEE is provided:
Image 'simple-bin' is missing optional external blobs but is still functional: tee-os
and even worse, build without any TEE OS even though we could provide
one via the TEE environment variable.
Finally, another option could be to move this hack under
arch/arm/mach-rockchip/Kconfig to make it Rockchip-specific or add a
depends on ARCH_ROCKCHIP. However OP-TEE OS on Aarch32 Rockchip boards
doesn't actually need any of that if SPL_OPTEE_IMAGE is set because
arch/arm/mach-rockchip/sdram.c then marks some hardcoded memory regions
in RAM as holes in DRAM, which has the same effect as reserved memory
regions I guess. I assume other platforms may use something different,
so it may be casting too wide of a net.
This commit is what I could come up with as a stopgap measure to avoid
building images that simply cannot reliably work and fail randomly.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
When building with clang, we see warnings such as:
error: field max_size within 'struct smbios_type7' is less aligned than
'union cache_size_word' and is usually due to 'struct smbios_type7'
being packed, which can lead to unaligned accesses
[-Werror,-Wunaligned-access]
when building drivers/sysinfo/smbios.c. Resolve this error by packing
the unions as well after verifying they are complete (16 or 32 bits).
Reviewed-by: Raymond Mao <raymondmaoca@gmail.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Dmitrii Sharshakov <d3dx12.xx@gmail.com> says:
Initially fix the inconsistency reported in reply to the previous
series and also make sure AArch64 images can be built with latest
Clang versions by guarding AArch32-specific options behind extra
config checks.
Tested qemu_arm_defconfig and qemu_arm64_defconfig with Clang 21,
mainline (to be 22) ce7f9f9c and also Clang 18 (for AArch64 only, as I
have not managed to build an AArch32 image with clang-18).
Link: https://lore.kernel.org/r/20251108-clang-cross-fixes-v1-0-ea6c4282844a@gmail.com
Clang is strict with respect to unknown options.
Therefore, only enable AArch32-specific options when CONFIG_ARM64
is not set.
Signed-off-by: Dmitrii Sharshakov <d3dx12.xx@gmail.com>
Clang cross-compilation worked when cross binutils were available
in PATH. However, when binutils are not in the PATH clang failed to
discover the assembler, falling back to host one.
Make --prefix always absolute, Clang supports this and will search for
e.g. $(prefix)-as for assembler. This makes sure user does not have to
add cross binutils to PATH for Clang build.
Fixes build for these examples (with qemu_arm(64)_defconfig):
make CC=clang-21 CROSS_COMPILE=/.../bin/arm-none-eabi-
make CC=clang-20 CROSS_COMPILE=/.../bin/aarch64-linux-gnu-
Also validated for the case when provided with cross toolchain on PATH:
PATH=/.../bin:$PATH make CC=clang-21 CROSS_COMPILE=arm-none-eabi- -j20
This patch does not affect GCC builds, and they have _not_ been
validated against regressions.
Reported-by: Tom Rini <trini@konsulko.com>
Closes: https://lore.kernel.org/u-boot/20251106221355.GZ6688@bill-the-cat/
Signed-off-by: Dmitrii Sharshakov <d3dx12.xx@gmail.com>
We found that some serial console may pull TX line to GROUND during board
boot time. Airoha uses TX line as one of it's BOOT pins. This will lead
to booting in RESERVED boot mode.
It was found that some flashes operates incorrectly in RESERVED mode.
Micron and Skyhigh flashes are definitely affected by the issue,
Winbond flashes are NOT affected.
Details:
--------
DMA reading of odd pages on affected flashes operates incorrectly. Page
reading offset (start of the page) on hardware level is replaced by 0x10.
Thus results in incorrect data reading. Usage of UBI make things even
worse. Any attempt to access UBI leads to ubi damaging. As result OS loading
becomes impossible.
Non-DMA reading is OK.
This patch detects booting in reserved mode, turn off DMA and print big
fat warning.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
The spinand driver do 3 type of dirmap requests:
* read/write whole flash page without oob
(offs = 0, len = page_size)
* read/write whole flash page including oob
(offs = 0, len = page_size + oob_size)
* read/write oob area only
(offs = page_size, len = oob_size)
The trick is:
* read/write a single "sector"
* set a custom sector size equal to offs + len. It's a bit safer to
round up "sector size" value 64.
* set the transfer length equal to custom sector size
And it works!
Thus we can find all data directly from dirmap request, so flash specific
parameters is not needed anymore. Also
* airoha_snand_nfi_config(),
* airoha_snand_nfi_setup()
functions becomes unnecessary.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Set custom sector size equal to flash page size including oob. Thus we
will always read a single sector. The maximum custom sector size is
8187, so all possible flash sector sizes are supported.
This patch is a necessary step to avoid usage of flash specific
parameters.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
This just reduce the number of modification of REG_SPI_NFI_CNFG and
REG_SPI_NFI_SECCUS_SIZE registers during dirmap operation.
This patch is a necessary step to avoid usage of flash specific
parameters.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
spi-airoha-snfi uses custom sector size in REG_SPI_NFI_SECCUS_SIZE
register, so setting of page/oob sizes in REG_SPI_NFI_PAGEFMT is not
required.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
During writing, the entire flash page (including OOB) will be updated
with the values from the temporary buffer, so we need to fill the
untouched areas of the buffer with 0xff value to prevent accidental
data overwriting.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Airoha snfi spi controller supports acceleration of DUAL/QUAD
operations, but does not supports DUAL_IO/QUAD_IO operations.
Luckily DUAL/QUAD operations do the same as DUAL_IO/QUAD_IO ones,
so we can issue corresponding DUAL/QUAD operation instead of
DUAL_IO/QUAD_IO one.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
This driver can accelerate single page operations only, thus
continuous reading mode should not be used.
Continuous reading will use sizes up to the size of one erase block.
This size is much larger than the size of single flash page. Use this
difference to identify continuous reading and return an error.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
This patch speed up cache reading/writing/updating opearions.
It was tested on en7523/an7581 and some other Airoha chips.
It will speed up
* page reading/writing without oob
* page reading/writing with oob
* oob reading/writing (significant for UBI scanning)
The only know issue appears in a very specific conditions for en7523 family
chips only.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Booting without this patch and disabled dirmap support results in
[ 2.980719] spi-nand spi0.0: Micron SPI NAND was found.
[ 2.986040] spi-nand spi0.0: 256 MiB, block size: 128 KiB, page size: 2048, OOB size: 128
[ 2.994709] 2 fixed-partitions partitions found on MTD device spi0.0
[ 3.001075] Creating 2 MTD partitions on "spi0.0":
[ 3.005862] 0x000000000000-0x000000020000 : "bl2"
[ 3.011272] 0x000000020000-0x000010000000 : "ubi"
...
[ 6.195594] ubi0: attaching mtd1
[ 13.338398] ubi0: scanning is finished
[ 13.342188] ubi0 error: ubi_read_volume_table: the layout volume was not found
[ 13.349784] ubi0 error: ubi_attach_mtd_dev: failed to attach mtd1, error -22
[ 13.356897] UBI error: cannot attach mtd1
If dirmap is disabled or not supported in the spi driver, the dirmap requests
will be executed via exec_op() handler. Thus, if the hardware supports
dual/quad spi modes, then corresponding requests will be sent to exec_op()
handler. Current driver does not support such requests, so error is arrised.
As result the flash can't be read/write.
This patch adds support of dual and quad wires spi modes to exec_op() handler.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
This operation is not needed because airoha_snand_write_data() and
airoha_snand_read_data() will properly handle data transfers above
SPI_MAX_TRANSFER_SIZE.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Coverity finds a potential integer overflow in the following code:
ncycles += ((op->data.nbytes * 8) / op->data.buswidth) / (op->data.dtr ? 2 : 1);
A quick analysis shows that the only caller of the suspicious code is the
spinand_select_op_variant() function from the drivers/mtd/nand/spi/core.c
file.
According to the code the value of op->data.nbytes is equal to
nanddev_per_page_oobsize(nand) + nanddev_page_size(nand)
Therefore it's maximum value a bit larger than 4Kb (I never seen flashes
with page size large than 4Kb). So op->data.nbytes always fits within
13 bits. As result an overflow will never happen.
Anyway it's better fix an issue to eliminate the error message.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
This option is only meaningful within the davinci nand driver, so drop
the statement here (which had no effect).
Signed-off-by: Tom Rini <trini@konsulko.com>
As was noted by Heinrich Schuchardt, some SoCs may not support 64-bit
divisions. Fix an issue by using lldiv() instead.
The code assumes that the benchmark never takes more than 4294 seconds
and thus the difference will be less than U32_MAX.
Also replace (speed / 1024) by (speed >> 10) to avoid potential 64-bit
division.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
The hidden symbol SPL_SYS_NAND_SELF_INIT was not being used correctly
leading to Kconfig dependency issues seen with "make allyesconfig". As
it's a select'd symbol we don't need to have a depends line on it, and
then in turn we need to also update the logic on SYS_NAND_PAGE_SIZE and
SYS_NAND_OOBSIZE.
Signed-off-by: Tom Rini <trini@konsulko.com>
All these chips are dual and quad capable. They are also DTR capable,
but the core is not yet ready for that.
Performances of all chips are comparable at 30MHz and are as follow:
Eraseblock single read speed: 938kiB/s
Eraseblock dual read speed: 1068kiB/s
Eraseblock quad read speed: 3751kiB/s
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add support for reading out the MAC address from SoC fuses on DH STM32MP1 DHSOM.
The DH STM32MP1 DHSOM may contain external ethernet MACs, which benefit from the
MAC address stored in SoC fuses as well, handle those consistently. This however
means the architecture setup_mac_address() cannot be used and instead a simpler
local fuse read out is implemented in the board file.
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The STM32MP13xx DHCOR SoM is populated with M24256 EEPROM that contains
an additional write-lockable page called ID page, which is populated with
a structure containing ethernet MAC addresses, DH item number and DH serial
number.
Read out the MAC address from the WL page between higher priority SoC fuses
and lower priority plain EEPROM storage area. Read out the DH item and serial
numbers and set environment variables accordingly.
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Move dh_add_item_number_and_serial_to_env() to common code, so it
can be used by both STM32MP13xx and iMX8MP DHSOM. No functional
change.
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Commit 6d91f0a3a1 ("board: st: common: cleanup dfu support") split
the vendor-specific DFU implementation into two files, but failed to
update other non-ST boards. This did not lead to noticeable breakage
with plain simple dfu-util, but it makes the ST proprietary programmer
CLI tool end in an infinite loop. Update the Makefile accordingly to
allow even that kind of tooling to work.
Fixes: 6d91f0a3a1 ("board: st: common: cleanup dfu support")
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Split the DH STM32MP13x based boards from ST STM32MP13x target,
this way the DH board specific code can be reused for STM32MP13x
DHSOM.
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Switch etzpc bus to simple-bus to prevent breakage on non-TFA systems.
This fixes boot of every STM32MP15xx DHSOM device.
Fixes: ad3cdc677d ("ARM: stm32mp: add ETZPC system bus driver for STM32MP1")
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add missing CPU_STM32MP255* cases in get_eth_nb() so that U-Boot
correctly reports 2 Ethernet interfaces on stm32mp255 devices.
This fixes the "ethernet not found" error during boot.
Signed-off-by: Md Asadullah <md.asadullah@eds-india.com>
Initially there was only one DSI bridge with one panel attached to this
device. This explained the call to uclass_first_device_err(UCLASS_PANEL,
...) which worked fine at the time.
Now that multiple bridges and panels, with different technologies, can
be plugged onto the board this way to get the panel device is outdated.
The lookup is done is two steps. First we circle through the
UCLASS_VIDEO_BRIDGE, and once we get one, we search through its
endpoints until we get a UCLASS_PANEL device available.
Acked-by: Yannick Fertre <yannick.fertre@foss.st.com>
Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
STM32MP2 SoCs feature a new version of the LTDC IP. This new version
features a bus clock, as well as a 150MHz pad frequency. Add its
compatible to the list of device to probe and handle quirks. The new
hardware version features a bus clock.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Acked-by: Yannick Fertre <yannick.fertre@foss.st.com>
Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>
The LVDS Display Interface Transmitter handles the LVDS protocol:
it maps the pixels received from the upstream Pixel-DMA (LTDC)
onto the LVDS PHY.
The LVDS controller driver supports the following high-level features:
• FDP-Link-I and OpenLDI (v0.95) protocols
• Single-Link or Dual-Link operation
• Single-Display or Double-Display (with the same content
duplicated on both)
• Flexible Bit-Mapping, including JEIDA and VESA
• RGB888 or RGB666 output
• Synchronous design, with one input pixel per clock cycle
• No resolution limitation.
Acked-by: Yannick Fertre <yannick.fertre@foss.st.com>
Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>
Add the compatible "panel-lvds" for simple-panel driver in U-Boot. In
Linux this compatible is managed by the driver
drivers/gpu/drm/panel/panel-lvds.c but in U-Boot the specific LVDS
features (bus_format/bus_flags) are not supported.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Yannick Fertre <yannick.fertre@foss.st.com>
Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>
The "Display Timings" in panel-common.yaml can be provided by 2 properties
- panel-timing: when display panels are restricted to a single resolution
the "panel-timing" node expresses the required timings.
- display-timings: several resolutions with different timings are supported
with several timing subnode of "display-timings" node
This patch update the parsing function to handle this 2 possibility
when index = 0.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Yannick Fertre <yannick.fertre@foss.st.com>
Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>
Add st,adc_usb_pd property in /config node for stm32mp135-dk-u-boot.
This needed to check board USB power delivery.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add support of STM32 ADCs to STM32MP13x. This patch introduces
stm32_adc_regspec structure, as this is already done in kernel
driver, to manage smartly the differences in register set
between STMP32MP15 and STM32MP13 ADCs.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
OP-TEE "arm,smc-id" is equal to 0xbc000000 but kernel DT has been
upstream with an incorrect value.
Fix it temporarily until kernel DT is fixed.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
OP-TEE "arm,smc-id" is equal to 0xbc000000 but kernel DT has been
upstream with an incorrect value.
Fix it temporarily until kernel DT is fixed.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Pull request efi-2026-01-rc3
CI:
* https://source.denx.de/u-boot/custodians/u-boot-efi/-/pipelines/28355
Documentation:
* Correct the linux/arm64 platform string for Docker builds
* Complete pytest dependencies list with missing packages
UEFI:
* Use Sphinx style comments in efi_selftest_console.c
* Don't include asm/global_data.h in lib/efi_client/efi_app.c twice
* efi_client: correct memset() return value
* Assure fitImage from capsule is used from 8-byte aligned address
* Fix warning when building efi_selftest_snp with clang
The fitImage may be stored in EFI update capsule at address that
is not aligned to 8 bytes. Since fitImage is a DT, new version of
libfdt 1.7.2 rejects such an unaligned DT. Patch the code and copy
the fitImage into aligned buffer in case it is not aligned. This
does increase overhead for unaligned fitImages in EFI capsules, but
tries to keep the overhead low for aligned ones.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
When building with clang, we see a warning:
lib/efi_selftest/efi_selftest_snp.c:63:18: error: field dhcp_hdr within
'struct dhcp' is less aligned than 'struct dhcp_hdr' and is usually due
to 'struct dhcp' being packed, which can lead to unaligned accesses
[-Werror,-Wunaligned-access]
when building lib/efi_selftest/efi_selftest_snp.c. Resolve this error by
packing struct dhcp_hdr as well, as the only place it is used also is
packed.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Memset() must return a pointer to the start of the updated memory block.
Fixes: 476476e73b ("efi: Add support for loading U-Boot through an EFI stub")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Convert function comments in efi_selftest_console.c to match
Sphinx style.
Correct function name in print_uuid() comment.
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Add missing dependencies to the pytest usage documentation and correct
the device tree compiler package name from 'dtc' to 'device-tree-compiler'.
This ensures users have the complete list of dependencies needed to run
the pytest test suite without errors.
Reviewed-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Signed-off-by: Kory Maincent (TI.com) <kory.maincent@bootlin.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
i2c_mux_select/deselect() are not called out of i2c-mux-uclass.c that's why
they should be static.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Heiko Schocher <hs@nabladev.com>
Rev.0.81 of the R-Car V4M Series Hardware User’s Manual removed the
"STPWT_EXTFXR" signal from the pin control register tables. As this is
further unused in the pin control driver, it can be removed safely.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Rev.0.71 of the R-Car V4M Series Hardware User’s Manual removed the
"CC5_OSCOUT" signal from the pin control register tables. As this is
further unused in the pin control driver, it can be removed safely.
Signed-off-by: Huy Bui <huy.bui.wm@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Rev.1.30 of the R-Car V4H Series Hardware User’s Manual removed the
"STPWT_EXTFXR" signal from the pin control register tables. As this is
further unused in the pin control driver, it can be removed safely.
Signed-off-by: Huy Bui <huy.bui.wm@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Rev.1.30 of the R-Car V4H Series Hardware User’s Manual removed the
"CC5_OSCOUT" signal from the pin control register tables. As this is
further unused in the pin control driver, it can be removed safely.
Signed-off-by: Huy Bui <huy.bui.wm@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Rev.1.30 of the R-Car V4H Series Hardware User’s Manual removed the
"AVB[01]_MII_*" signals from the pin control register tables. As these
are further unused in the pin control driver, they can be removed
safely.
Signed-off-by: Thanh Quan <thanh.quan.xn@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
This driver cannot build when DM_USB_GADGET is enabled as both options
control building of files that use the same global namespace and
functionality. In this case make CI_UDC depend on DM_USB_GADGET being
disabled as non-DM support is the legacy choice.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
All instances of the U_BOOT_DRIVER must use a unique name or they will
lead to link time failures due to name space conflicts when both are
present. Most of the XHCI drivers follow pattern of xhci_xxx in their
name, but a few used "usb_xhci". Change these to follow the pattern of
the rest of the XHCI glue drivers.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
The DWC2 OTG driver depends on an ARM-specific header file to compile,
so make it depend on ARM.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
The last of the users of the legacy musb drivers have been
migrated so now remove the old musb stack, all users should
now be using the new musb stack if they need this functionality.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
[trini: Remove a Makefile reference that was missed in v1]
Signed-off-by: Tom Rini <trini@konsulko.com>
The USB_OMAP3 driver was (re)added in commit e74e9f620a as part
of migrating to DM_USB but the config already had MUSB_OMAP2PLUS
which is the newer musb driver and what other omap3 devices use.
So drop it so we can drop the old driver.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
It makes no sense to ask about nor enable SPL_USB_GADGET without
SPL_FRAMEWORK being enabled. Attempting to do so leads to Kconfig noting
dependency issues. Add the missing dependency.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Add the compatible string of Exynos7's PMU as defined in upstream
dt-schema. This also supports derivative PMUs as defined in schema.
There's no additional setup required here, so pmu_init is skipped.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add the compatible for Exynos8895 UART as described in upstream
devicetree bindings. This enables support for Exynos8895 and other
similar UART devices, such as Exynos7870. Other than that, the driver
works as-is.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Reviewed-by: Henrik Grimler <henrik@grimler.se>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The pinctrl blocks for Exynos7870 and Exynos7880 are similar, however in
Exynos7870, the CCORE block is actually referred to as MIF. Since
ordering happens lexically, it isn't directly compatible with
samsung,exynos78x0-pinctrl.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The devicetree of Samsung devices typically have the pin controller and
GPIO bank descriptors under the same pinctrl node. In U-Boot, these are
handled by two separate drivers. It is not possible to invoke both
drivers from a single node compatible.
Bind the GPIO driver on pinctrl driver bind, with the same OF node as
the pinctrl driver. This solution is already being used in other pinctrl
drivers. The hierarchy, as represented in `dm tree`, is as follows:
pinctrl@13750000
|-- gpio-banks
| |-- gpr0-gpio-bank
| |-- gpr1-gpio-bank
| |-- gpr2-gpio-bank
| |-- gpr3-gpio-bank
| `-- gpr4-gpio-bank
|-- sd0-bus-width1-pins
|-- sd0-bus-width4-pins
|-- sd0-bus-width8-pins
`-- sd0-clk-pins
Since a bind function doesn't exist, create and add it to all pinctrl
drivers.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
There may be cases where the flags set for a clock is not available.
This is usually the case with clocks which have been retrieved using
clk_request(). However, clock flags are found in their respective
private clock struct, so use that instead.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Introduce a simple clock driver for Exynos7870's CMU blocks, more
specifically, CMU_MIF, CMU_FSYS, and CMU_PERI banks. This should be
enough to serve U-Boot's minimal requirements.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The request function performs a simple check if the clock with the
provided ID is present or not. This is done with a simple call to
clk_get_by_id(). A non-zero return value indicates that the requested
clock is not available.
In some cases, clk->dev points to the clock bank device instead of
the clock device. This pointer is therefore overwritten in order to
reference to the correct device instance.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
PLL1417X seem to be compatible with PLL0822X, as also seen in the
respective Linux kernel driver. Add an enum entry for the type, while
merely being an alias for PLL0822X.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add register functions for fixed rate and fixed factor clock drivers.
The vendor-specific structs defined are borrowed from the CCF driver
found in the Linux kernel.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The device pointer set as NULL causes problems when clock banks depend
on clocks from another clock bank. In such case, the appropriate clock
needs to be resolved from OF phandle arguments, which is not possible if
the associated device is not provided. Make necessary changes to make
the correct device pointer available.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
In general, we want to fail the whole pipeline as soon as we can if we
spot an error while also letting bigger jobs get started as soon as
possible. Currently we use the "Run binman, buildman, dtoc, Kconfig and
patman testsuites" job from the testsuite stage to unblock the next
stage as this test is complex enough that if it passes, likely the whole
stager will pass. Using this same logic, unblock the world build (and
sjg-lab) stages if "sandbox test.py" has completed as if there's no
failures here, there's likely not failures in the rest of the test.py
stages.
Signed-off-by: Tom Rini <trini@konsulko.com>
Change the existing regex "/capsule.*.efi-capsule" to
also ignore the following files when building the sandbox:
capsule_in.capsule1.efi-capsule
capsule_in.capsule10.efi-capsule
capsule_in.capsule11.efi-capsule
capsule_in.capsule2.efi-capsule
capsule_in.capsule3.efi-capsule
capsule_in.capsule4.efi-capsule
capsule_in.capsule5.efi-capsule
capsule_in.capsule6.efi-capsule
capsule_in.capsule7.efi-capsule
capsule_in.capsule8.efi-capsule
capsule_in.capsule9.efi-capsule
As test/overlay folder was renamed to test/fdt_overlay,
fix the related ignore entries:
test/fdt_overlay/test-fdt-overlay-stacked.dtbo.S
test/fdt_overlay/test-fdt-overlay.dtbo.S
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
There is a memory leak during the scsi scan process due to the
strdup'ed name string is never freed. Actually it is unnecessary
to pass a strdup'ed name string to blk_create_devicef() as we can
use the name string on the stack directly.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
OMAP GPIO driver needs TI_SYSC to initialize its clocks when
using a devicetree-based setup.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
There are cases where qfw_read_entry() does not set the output parameter
passed by address. This occurs with qfw_sandbox_read_entry_dma, which
leaves the size variables uninitialized and causes a segfault when running
bootflow scan in U-Boot sandbox.
$ ./u-boot
...
U-Boot 2026.01-rc1-00199-gc2637036b8f0 (Nov 04 2025 - 10:32:21 +0100)
...
Hit any key to stop autoboot: 0
=> bootflow scan
efi_var_to_file() Cannot persist EFI variables without system partition
efi_tcg2_register() Missing TPMv2 device for EFI_TCG_PROTOCOL
efi_rng_register() Missing RNG device for EFI_RNG_PROTOCOL
scanning bus for devices...
[3] 1015761 segmentation fault (core dumped) ./u-boot
Initalize all these variables to 0 to fix this issue.
Signed-off-by: Kory Maincent (TI.com) <kory.maincent@bootlin.com>
Support for using "u-boot,dm-..." rather than "bootph-..." has been
deprecated since February 2023. Any platforms using this have had a
console message saying to migrate by 2023.07. Go and remove all support
here now, for the v2026.01 release.
The results of this change that aren't clear from the above are that we
still have a checkpatch.pl error message, and document in
doc/develop/spl.rst that they have been migrated since 2023. We also
change the key2dtsi.py tool to use the correct bootph phase rather than
the legacy phase.
Signed-off-by: Tom Rini <trini@konsulko.com>
Instead of resolving clock control flags using SCMI_CLOCK_ATTRIBUTES
during probe for each and every clock, resolve the clock control
flags using SCMI_CLOCK_ATTRIBUTES when the clock control flags are
first used. Because most clock are never used by U-Boot, this allows
reducing the amount of SCMI_CLOCK_ATTRIBUTES considerably, and this
improve probe time of the scmi clock driver and U-Boot start up time.
On Renesas X5H, with 1700+ SCMI clock, the boot time improved by 1.7s .
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The clock names are retrived via SCMI_CLOCK_ATTRIBUTES, called for each
clock ID. This may take a lot of time to complete and is not strictly
necessary. Register each clock as "scmi-%zu" instead, and let the first
call of SCMI_CLOCK_ATTRIBUTES fill in the actual clock name.
This has a side effect, which can be considered both an upside and also
a downside. Unused clock are never renamed and retain their placeholder
"scmi-%zu" name, which avoids empty clock names for nameless SCMI clock,
and avoids the name resolution and improves boot time. But for those
SCMI clock which do have name, that name is not listed until the clock
are used.
This is a preparatory patch for deferred issue of SCMI_CLOCK_ATTRIBUTES.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Pull clock control flags resolution into dedicated function and
call it from each site that does access clock control flags. No
functional change.
This is a preparatory patch for deferred issue of SCMI_CLOCK_ATTRIBUTES.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Allocate all sub-driver instance data at once. The amount of data that
have to be allocated is known up front, so is the size of the data, so
there is no need to call malloc() in a loop, mallocate all data at once.
The upside is, less heap fragmentation and fewer malloc() calls overall,
and a faster boot time.
The downside is, if some of the clock fail to register, then the clock
driver cannot free parts of the bulk allocated sub-driver instance data.
Such a failure can only occur if clk_register() were to fail, and if that
happens, the system has more significant problems. Worse, if a core clock
driver fails to probe, the system has even bigger problem.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When not using Common clock framework(CCF), calls to
scmi_clk_set_parent returns -ENOTSUPP, which should not be the case.
Fix that.
Fixes: 15fdfef664 ("clk: scmi: check the clock state/parent/rate
control permissions)
Signed-off-by: Kamlesh Gurudasani <kamlesh@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
SCMI v3.2 introduces a new clock CONFIG_SET message format that can
optionally carry also OEM specific configuration values beside the usual
clock enable/disable requests. Add support to use such new format when
talking to a v3.2 compliant SCMI platform.
Support existing enable/disable operations across different clock protocol
versions: this patch still does not add protocol operations to support the
new OEM specific optional configuration capabilities.
No functional change for the SCMI drivers users of the related enable and
disable clock operations.
[Marek: Remodel after Linux e49e314a2cf7 ("firmware: arm_scmi: Add clock v3.2 CONFIG_SET support")
Support both old < 2.1 and new >= 2.1 protocol versions.
Update commit message based on Linux one]
Signed-off-by: Vinh Nguyen <vinh.nguyen.xz@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
MMU region cache behavior configuration for SCMI/SMT mailboxes is
platform specific. Even on ARM systems, the mailbox memory may not
even be located in any cacheable MMU region and may instead reside
in some SRAM. Remove this non-generic cache behavior configuration
code from generic code path.
It is unlikely that any platform is affected by this change if it
did configure its MMU regions correctly on start up. Platforms
which might be affected are i.MX94/95 and STM32MP.
Fixes: 240720e905 ("firmware: scmi: mailbox/smt agent device")
Fixes: 2a3f161c8b ("scmi: correctly configure MMU for SCMI buffer")
Fixes: b2ae10970d ("firmware: scmi: use PAGE_SIZE alignment for ARM64")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Tested-by: Alice Guo <alice.guo@nxp.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fix multiple instances of copy-paste errors. Fill in missing
headers for CLOCK_GET_PERMISSIONS message and response.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Anshul Dalal <anshuld@ti.com> says:
This patch series adds support for AM6254atl SiP (or AM62x SiP for
short) to U-Boot.
The OPN (Orderable Part Number) 'AM6254atl' expands as follows[1]:
AM6254atl
||||
|||+-- Feature Lookup (L indicates 512MiB of integrated LPDDR4)
||+--- Device Speed Grade (T indicates 1.25GHz on A53 cores)
|+---- Silicon PG Revision (A indicates SR 1.0)
+----- Core configuration (4 indicates A53's in Quad core config)
AM62x SiP provides the existing AM62x SoC with 512MiB of DDR
integrated in a single packages. The first 4 patches in the series
are cherry-picked from the devicetree-rebasing repository at
'v6.18-rc2-dts'.
Link: https://lore.kernel.org/r/20251025-62sip_support-v3-0-b4c8314d0055@ti.com
Hrushikesh Salunke <h-salunke@ti.com> says:
This series enables PCIe Endpoint mode on TI's J784S4 SoC. The J784S4
SoC features two Cadence PCIe controller instances (PCIe0 and PCIe1)
that can operate in endpoint mode. This series adds support for
configuring these controllers with up to 4 lanes.
Key changes include:
- Adding a stabilization delay after power domain reset to prevent
timing-related initialization issues
- SERDES mux configuration support for proper lane routing, which is
essential for SoCs where SERDES lanes are shared between multiple
controllers (PCIe, USB, etc.) with different configurations across
boot phases
- J784S4 SoC endpoint configuration with 4-lane support
- Disabling unconfigured endpoint functions to prevent enumeration
issues on the Root Complex side
This series has been tested on J784S4 EVM with PCIe endpoint boot
configuration. Following are the corresponding test logs.
https://gist.github.com/hrushikesh221/331d65f45f43fd138f57e6adb61c4332
Link: https://lore.kernel.org/r/20251023114604.3655625-1-h-salunke@ti.com
Guillaume La Roque (TI.com) <glaroque@baylibre.com> says:
This series adds EEPROM board detection support for AM62x and refactors
the board detection code across AM6x family boards to eliminate code
duplication.
The series introduces two new generic functions for AM6x boards:
- do_board_detect_am6(): Reads the on-board EEPROM with fallback logic
to alternate I2C addresses
- setup_serial_am6(): Sets up the serial number environment variable
from EEPROM data
Link: https://lore.kernel.org/r/20251103-am62xeeprom-v3-0-e390779c0fc5@baylibre.com
Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu> says:
This patch series adds basic support for the boards based on Airoha
EN7523/EN7529/EN7562 SoCs. Due to ATF restrictions these boards are
able to run 32-bit OS only.
This patch series adds support for the following hardware:
* console UART
* ethernet controller/switch
* spinand flash (in non-dma mode)
The following issues may be expected:
* Extra slow UBI attaching in U-Boot (up to 20 sec with fastmap enabled).
This is caused by the lack of DMA support in the U-Boot airoha-snfi driver.
* Linux airoha-snfi driver in some cases might damage you flash data
(see: https://lore.kernel.org/lkml/20251012121707.2296160-15-mikhail.kshevetskiy@iopsys.eu/)
* Latest linux kernel is recommended to properly support flashes
with more than one plane per lun
(see: https://lore.kernel.org/lkml/20251012121707.2296160-7-mikhail.kshevetskiy@iopsys.eu/)
* It's NOT recommended to use flashes working in continuous mode because
U-Boot airoha-snfi driver does not support such flashes properly.
The patches was tested on the board:
- SoC: Airoha EN7562
- RAM: 512 MB
- SPI NAND: 4 Gbit, made by Toshiba
- Linux boot: was NOT tested
The U-Boot was chain-loaded from the running U-Boot. Airoha ATF-2.3 does
not allow easily chain-loading of U-Boot from U-Boot, so a special FIT
image (mimic linux kernel) was created
1) Create u-boot.its file with the following contents:
=== cut here ===
/dts-v1/;
/ {
description = "ARM OpenWrt FIT (Flattened Image Tree)";
#address-cells = <1>;
images {
u-boot-ram {
description = "OpenWrt U-Boot RAM image";
data = /incbin/("u-boot.bin.lzma");
type = "kernel";
arch = "arm";
os = "linux";
compression = "lzma";
load = <0x81e00000>;
entry = <0x81e00000>;
hash@1 {
algo = "crc32";
};
hash@2 {
algo = "sha1";
};
};
fdt-1 {
description = "OpenWrt device tree blob";
data = /incbin/("dts/upstream/src/arm/airoha/en7523-evb.dtb");
type = "flat_dt";
arch = "arm";
compression = "none";
hash@1 {
algo = "crc32";
};
hash@2 {
algo = "sha1";
};
};
};
configurations {
default = "config-ram-uboot";
config-ram-uboot {
description = "OpenWrt RAM U-Boot";
kernel = "u-boot-ram";
fdt = "fdt-1";
};
};
};
==================
2) Create u-boot.itb image to chain-load new u-boot from the old one
lzma_alone e u-boot.bin u-boot.bin.lzma
mkimage -f u-boot.its u-boot.itb
3) Load new u-boot from the old one
U-Boot> tftpboot u-boot.itb && bootm
Link: https://lore.kernel.org/r/20251101004503.2379529-1-mikhail.kshevetskiy@iopsys.eu
TI's AM6254atl (or AM62x SiP for short) provides the existing AM62x SoC
with 512MiB of DDR integrated in a single package.
This patch adds the necessary U-Boot devie tree files, the required
defconfigs along with the documentation for the AM62x SiP EVM.
AM62x SiP differs from the already supported AM62x in following ways:
- OP-TEE for the AM62x resides from 0x9e800000 to 0xa0000000 which needs
to be moved to 0x80080000 to free up space at end of DDR in AM62x SiP
with 512MiB of memory. This is required to allow U-Boot to relocate to
end of DDR before booting to the kernel.
- Changes to the env:
1. splashimage address updated from 0x80200000 to 0x81a00000
2. DFU addresses updated to match updated TEXT_BASE for SPL and U-Boot
Signed-off-by: Anshul Dalal <anshuld@ti.com>
This patch adds the dt for SK-AM62-SIP, which uses the existing
SK-AM62 board design with the new AM6254atl SiP. This changes the
location of memory node from the board dts to SoC level dtsi
(k3-am6254atl in our case).
Therefore this patch introduces the new 'k3-am625-sk-common.dtsi'
which represents the common hardware used for both 'am625-sk' and
'am6254atl-sk' boards with the inheritance hierarchy modified to:
k3-am625-sk.dts:
k3-am62 k3-am62x-sk-common
| |
k3-am625 k3-am625-sk-common
| |
+-----+------+
|
k3-am625-sk
k3-am6254atl-sk.dts:
k3-am62
|
k3-am625 k3-am62x-sk-common
| |
k3-am6254atl k3-am625-sk-common
| |
+-------+--------+
|
k3-am6254atl-sk
Signed-off-by: Anshul Dalal <anshuld@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://patch.msgid.link/20250814134531.2743874-5-anshuld@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
[ upstream commit: 2517e476b819df986fa1fe53927c099032bb72dc ]
(cherry picked from commit 58cd89aff167661dbae0c9911282ea3f1b8212cc)
The k3-am62x-sk-common dtsi represents the common hardware used across
am62x EVMs which can be configured with various DDR sizes or none (with
DDR integrated in the package) based on the specific am62x SoC used.
Therefore this patch moves the memory node and the SoC specific k3-am625
dtsi out of sk-common and into the board dts files. No functional change
is intended from this patch. The device-tree inheritance is changed as
follows:
Before:
k3-am62
^
k3-am625
^
k3-am62x-sk-common
^
am62x EVMs (k3-am625-sk, k3-am62-lp-sk)
After:
k3-am62
^
k3-am625 k3-am62x-sk-common
^ ^
am62x EVMs (k3-am625-sk, k3-am62-lp-sk)
Signed-off-by: Anshul Dalal <anshuld@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://patch.msgid.link/20250814134531.2743874-2-anshuld@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
[ upstream commit: e0b9feca7329c495a76891d7766a781dea73787d ]
(cherry picked from commit 0b0edbbdf43bac6b28dd59c88647bd5e0b73ffea)
Add the label name 'reserved_memory' to the reserved-memory node in all
K3 AM6* board level dts files. This is done so that the node can be
referenced and extended to add more carveout entries as needed in future
refactoring patches.
Signed-off-by: Beleswar Padhi <b-padhi@ti.com>
Acked-by: Andrew Davis <afd@ti.com>
Link: https://patch.msgid.link/20250908142826.1828676-13-b-padhi@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
[ upstream commit: 4f1aee4723a796a92f17b23699dc861b582ddfd2 ]
(cherry picked from commit 58c447fe500d78f5adc373b4945d8317e11df072)
TI's J784S4 SoC has two instances of PCIe Controller namely PCIe0 and
PCIe1 which are Cadence PCIe Controllers. Enable corresponding configs
to support PCIe Endpoint mode of operation on these instances.
Signed-off-by: Hrushikesh Salunke <h-salunke@ti.com>
TI's J784S4 SoC has two instances of PCIe Controller namely PCIe0 and
PCIe1 which are Cadence PCIe Controllers. Add support to configure PCIe
instances in Endpoint mode of operation.
While at it disable all endpoint functions except function 0 during
probe to prevent the Root Complex from enumerating unconfigured
functions. This ensures only properly configured endpoint functions
are visible to the host and avoids enumeration issues with
multi-function devices.
Signed-off-by: Hrushikesh Salunke <h-salunke@ti.com>
Probe the mux device early in the SERDES configuration flow to ensure
proper lane routing before PHY initialization. This is required for SoCs
where SERDES lanes can be muxed between different controllers
(PCIe, USB, etc), and different mux configurations are required between
different boot phases.
Signed-off-by: Hrushikesh Salunke <h-salunke@ti.com>
Add a 1ms delay after powering on the PCIe power domain to ensure
the controller stabilizes before subsequent operations. This prevents
potential timing issues during PCIe endpoint initialization.
The delay allows sufficient time for the power domain to fully come
up and the hardware to be in a stable state before configuration
begins.
Signed-off-by: Hrushikesh Salunke <h-salunke@ti.com>
Replace the board-specific implementation of do_board_detect()
with a call to the generic do_board_detect_am6() function to
avoid code duplication across AM6x family boards.
The generic function provides the same functionality with
additional fallback logic to try alternate EEPROM addresses.
Reviewed-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Signed-off-by: Guillaume La Roque (TI.com) <glaroque@baylibre.com>
Replace the board-specific implementation of do_board_detect() and
setup_serial() with calls to the generic do_board_detect_am6() and
setup_serial_am6() functions.
The generic function provides the same functionality with
additional fallback logic to try alternate EEPROM addresses.
Reviewed-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Signed-off-by: Guillaume La Roque (TI.com) <glaroque@baylibre.com>
I2C EEPROM data contains the board name and its revision.
Add support for:
- Reading EEPROM data and store a copy at end of SRAM
- Updating env variable with relevant board info
- Printing board info during boot
Use the generic do_board_detect_am6() and setup_serial_am6()
functions to avoid code duplication across AM6x family boards.
Reviewed-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Signed-off-by: Guillaume La Roque (TI.com) <glaroque@baylibre.com>
Add two new generic functions for AM6x family boards to simplify
board-specific implementations:
- do_board_detect_am6(): Generic board detection function that reads
the on-board EEPROM. It first attempts to read at the configured
address, and if that fails, tries the alternate address
(CONFIG_EEPROM_CHIP_ADDRESS + 1). This provides a common
implementation that can be used across different AM6x boards.
- setup_serial_am6(): Sets up the serial number environment variable
from the EEPROM data. The serial number is converted from
hexadecimal string format to a 16-character hexadecimal
representation and stored in the "serial#" environment variable.
Both functions are protected by CONFIG_IS_ENABLED(TI_I2C_BOARD_DETECT)
and are designed to be used by AM62x, AM64x, AM65x, and other AM6x
family boards.
Reviewed-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Signed-off-by: Guillaume La Roque (TI.com) <glaroque@baylibre.com>
This allow us remove some an7581/an7583 specific code and use a common
code instead.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
This patch unify probing code using airoha SCU regmap helper, thus a
common function can be used instead of an7581/an7583 specific ones.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
In preparation for support for Airoha AN7583, convert the driver to
regmap API. This is needed as Airoha AN7583 will use syscon to access
reset registers.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This adds clock driver for airoha en7523/en7529/en7562 SoCs. The code
is based on corresponding linux driver.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
We need access SCU and CHIP_SCU regmaps in several places (clk-airoha,
reset-airoha, airoha_eth). Unfortunately these regmaps can't be easily
retrieved with a common code, because of different Airoha SoCs uses
a different dts structure.
To make life easy we can write a commonly named SoC specific helpers
for these tasks. This patch implements helpers for Airoha EN7523 SoC.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
We need access SCU and CHIP_SCU regmaps in several places (clk-airoha,
reset-airoha, airoha_eth). Unfortunately these regmaps can't be easily
retrieved with a common code, because of different Airoha SoCs uses
a different dts structure.
To make life easy we can write a commonly named SoC specific helpers
for these tasks. This patch implements helpers for Airoha AN7581 SoC.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Basic support for en7523/en7529/en7562 SoCs. Within a patch
only serial console will be supported.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
This is required because airoha/en7523 will be added with the following
patches. Without this line config for en7523 will be created instead of
an7581.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Clean up the sound Kconfig options to let all sound devices depend on
CONFIG_SOUND.
Before this patch it was possible to select CONFIG_SOUND_MAX98357A even
with CONFIG_SOUND=n.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Update the resource management configuration (rm-cfg.yaml) to align
with the default configuration provided in TI's AM62xx Processor SDK
Linux version 11.01.05.03, generated using the K3 Resource Partitioning
Tool.
This matches the configuration from board/ti/am62x/rm-cfg.yaml and the
notable change is the sharing of MCU GPIO interrupts between DM R5 and
A53 cores, and reservation of an additional virtual interrupt and event
for TIFS usage.
Signed-off-by: Vitor Soares <vitor.soares@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Anshul Dalal <anshuld@ti.com>
If missing, lbaint_t typedef will not be found in some cases.
[The proper fix for the commit above at the time would have been to
include ide.h as only since commit 1a73661bc7 ("dm: Add a new header
for block devices") is the typedef in blk.h]
Fixes: 04735e9c55 ("Fix ext2/ext4 filesystem accesses beyond 2TiB")
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
The general python documentation for the subprocess class recommends
that run() be used in all cases that it can handle. What we do in
RunAndLog is simple enough that run() is easy to switch to. In fact,
looking at this exposed a problem we have today, which is that we had
combined stdout and stderr but then looked at both stdout and stderr as
if they were separate. Stop combining them.
Signed-off-by: Tom Rini <trini@konsulko.com>
Quentin Schulz <foss+uboot@0leil.net> says:
This improves readability in menuconfig by putting PWM symbols under a
Kconfig menu.
It also groups PWM symbols that depend on DM_PWM together under an if
DM_PWM block so that we don't need to always list the dependency in the
depends on of the symbol.
No intended change in behavior except how it shows in menuconfig.
Link: https://lore.kernel.org/r/20251030-pwm-kconfig-v2-0-d151a42784ce@cherry.de
This simplifies the "depends on" since we don't need DM_PWM listed
explicitly there as it already is made explicit via the surrounding
"if". No intended change in behavior.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Since it is registered as a U_CLASS_DRIVER, Sandbox PWM driver is a
Driver Model Driver and thus to be usable depends on DM_PWM to be
selected.
Let's make sure of that via the appropriate Kconfig option.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
So it's visually better split from the other subsystems when using
menuconfig.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Add support for R-Car Gen5 SoCs into the driver.
The default quirk is identical to previous generation.
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> # Tweak commit message
Some shared memory mailboxes may have empty receive operation,
because the data are polled by upper layers directly from the
shared memory region, and there is no completion interrupt or
bit of any sort. Allow empty .recv callback, and if the .recv
callback is empty, exit from mbox_recv() right away, because
any polling for completion here would be meaningless.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Alice Guo <alice.guo@nxp.com>
Isolate Renesas R-Car Gen3 clock driver to R-Car Gen3 and Gen4 and RZ/G2L.
The Renesas R-Car Gen5 uses SCMI clock protocol driver instead. This is
a preparatory change for R-Car Gen5. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Pull request efi-2026-01-rc2
CI: https://source.denx.de/u-boot/custodians/u-boot-efi/-/pipelines/28208
Documentation:
* bootstd: Describe environment variable extension_overlay_addr
environment and remove extension support from TODO list
EFI:
* Correct the detection of the video mode in the EFI payload app:
- Use struct efi_gop_mode_info in the definition of struct
efi_entry_gopmode.
- In function get_mode_from_entry() use the correct type for the video
mode structure.
* Use a valid error code as return value in efi_store_memory_map().
* Avoid a memory leak for the variable name in efi_bl_create_block_device().
* Correct the code indentation in efi_uc_stop().
* Correct the description of struct efi_priv.
* Fix typos in code comments.
Other:
* qfw: Add more fields and a heading to qfw list
* Fix the support for ACPI pass-through on ARM and RISC-V:
Avoid zeroing out the XSDT address
* test: provide unit test for 'acpi list' command
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEbcT5xx8ppvoGt20zxIHbvCwFGsQFAmkNj/kACgkQxIHbvCwF
# GsS8NQ/6Aj+Z54HJTIEfoXssvElLr5ATactrCxszq42i/yy6dLqa2Ym1afG6w1XS
# 1ZbCeU/bCXFke5Tsz+x89gEfckUm83oTwngwcID0WR1qn8mWjwR7tM5MuORq8NxU
# 7NwLuFs9O/QZihagKdz6hv1/Y+cBwiAYLY16EYVSuUlbLaKQo3QvxwWkqG3jdKWV
# Rm58/PolU+2h04MBwP0SxSduX4OyRF/tMOGjf5RGLyqCyj8kIgdu7PvUAPMM+Gps
# KemL59V0Bdv8hlF4JknmPz+idtZg2nHIDdNrBZvoxwzwGQeRZ1YXAMruRxZXqDYL
# tiuDp6HMv/GfIIGkz14tJtJMdboaAybAnluPWGalx8JQJqJzEPww0R+9s4KKQeWL
# mHgRyl6PxVV9p19f79Qq6q6ETwrFDX0YH3pdrGUk3DBa3lDt0UsEAnuW4FvaJ8tx
# 3PMrjKAxpxocT0hglsMVnptnfvDEigMsjwH/TWrau83mY+juxFQLjm+U4vye+qCa
# 4zXjjLas18+eRcrv2KxU7teakyi1Jp+WbqHq37L26YcQMaLq/RkBc0bTrsreKKLu
# jprYFpvc7EJpH2Fd1XWaZ2EnxXcVSJSvrY/iwRQqb6wbwQ6XGtMvSh3IFY8IzAoh
# N2Pj78oaYqyL1q/TftuZWhEHo3a0M/HfM4D+oMSHzJtWCb0wZHE=
# =OGcS
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 07 Nov 2025 12:21:45 AM CST
# gpg: using RSA key 6DC4F9C71F29A6FA06B76D33C481DBBC2C051AC4
# gpg: Good signature from "Heinrich Schuchardt <xypron.glpk@gmx.de>" [unknown]
# gpg: aka "[jpeg image of size 1389]" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 6DC4 F9C7 1F29 A6FA 06B7 6D33 C481 DBBC 2C05 1AC4
Add DWMCI_QUIRK_DISABLE_FMP flag to Exynos850 driver data to make the
driver disable FMP in case of Exynos850 chip. That makes eMMC on
Exynos850 functional when U-Boot is executed during USB boot.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Up until now "samsung,exynos7-dw-mshc-smu" compatible was used for
Exynos850 SoC, as it's present in its device tree. But Exynos850 device
tree also supports "samsung,exynos850-dw-mshc-smu" compatible string.
Add it in compatible ID list in the driver so that it can be matched
against this string for Exynos850 device tree.
No functional change, as the driver data is just a copy of
"samsung,exynos7-dw-mshc-smu" data for now.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add DWMCI_QUIRK_DISABLE_FMP which disables Flash Memory Protector (FMP)
during driver's init. It's usually done by early bootloaders, but in
some cases (like USB boot) the FMP may be left unconfigured. The issue
was observed on Exynos850 SoC (the E850-96 board). Enabling this quirk
makes eMMC functional even in such cases.
No functional change, as this feature is only added here but not enabled
for any chips yet.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Exynos DW MMC glue layer driver have seen a lot of changes recently.
Stabilize the coding style.
No functional change.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Do not over-expose the private dw_mmc API. The glue layer drivers at
this point shouldn't be aware and shouldn't use the generic
dwmci_send_cmd() and dwmci_set_ios() functions. Making those functions
public causes a "leaky abstraction" issue. It clutters the public
interface of generic dw_mmc driver and possibly leads to improper usage
of those functions, so it's a bad design.
If struct dm_dwmci_ops has to be extended, do so by copying it first
(like it's done for example in snps_dw_mmc driver). That also makes sure
the future changes to struct dm_dwmci_ops in dw_mmc driver will be
automatically reflected in all extended copies, and avoid code
duplication.
This effectively reverts commit ef3b16bb8e73 ("mmc: dw_mmc: export
dwmci_send_cmd() and dwmci_set_ios()").
No functional change.
Fixes: ef3b16bb8e73 ("mmc: dw_mmc: export dwmci_send_cmd() and dwmci_set_ios()")
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Instead of extending dm_dwmci_ops by copy-pasting the structure code
first, copy the actual structure data with memcpy() and then set the
.execute_tuning field. Now if struct dm_dwmci_ops gets modified in
future, these changes will be automatically reflected in struct
exynos_dwmmc_ops, which prevents possible issues in future. It also
avoids code duplication.
No functional change, but it can prevent possible isssues in future.
Fixes: eda4bd29929c ("mmc: exynos_dw_mmc: add support for MMC HS200 and HS400 modes")
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The null check for loader in boot_from_devices was moved earlier in the
code path by the commit ae409a84e7 ("spl: NULL check variable before
dereference"), therefore the subsequent null checks for loader are not
necessary.
This patch removes those checks and refactors the prints to be more
useful in case of errors.
Signed-off-by: Anshul Dalal <anshuld@ti.com>
Anshul Dalal <anshuld@ti.com> says:
This patch set adds support for falcon boot on AM62a, 62p and 62x by bypassing
A53 SPL and U-boot.
Existing Boot flow:
R5 SPL -> ATF -> A53 SPL -> U-Boot -> Linux Kernel
Updated flow:
R5 SPL -> ATF -> Linux Kernel
U-Boot's falcon mode expects the jump from SPL to kernel to happen on the same
core which is not directly applicable for our heterogeneous platforms since
ATF, OPTEE and other non SPL binaries from tispl.bin should be loaded before the
kernel by the R5 SPL.
So we have to use a different flow to bypass A53 SPL and U-Boot, we first load
the newly added tispl_falcon.bin instead of tispl.bin which lacks u-boot-spl.bin
(A53's SPL) and the corresponding fdt. This sets up dm, tifs, optee and
atf. Once loaded, we load the kernel and the dtb (with fixups) at ATF's
PRELOADED_BL33_BASE and K3_HW_CONFIG_BASE.
NOTE:
Since we're now using the SPL to load the kernel and kernel expects a 2MiB
aligned load address, the existing PRELOADED_BL33_BASE has to be changed for ATF
to 0x82000000 with K3_HW_CONFIG_BASE set to 0x88000000 for the DTB.
Link: https://lore.kernel.org/r/20251031073800.344500-1-anshuld@ti.com
This patch adds user documentation for R5 falcon mode for AM62
platforms. The main section is added to am62x_sk.rst and other documents
just include the relevant sections. Steps to build falcon support, usage
and the modified R5 memory map have been documented.
Two svg images have also been added for reference, one for the modified
tifalcon.bin and other for the fitImage format specific to R5 falcon
mode.
Signed-off-by: Anshul Dalal <anshuld@ti.com>
The bootargs are passed to the kernel in the chosen node, this patch
adds support for populating bootargs in the dtb if missing.
The values for kernel boot params is taken from the env, with 'boot' and
'bootpart' specifying the rootfs for the kernel similar to the
non-falcon boot flow.
Signed-off-by: Anshul Dalal <anshuld@ti.com>
This patch adds fdt fixups to the kernel device-tree in R5 falcon mode,
these fixups include fixing up the core-count, reserved-memory etc.
The users can opt out by disabling the respective CONFIG_OF_*_SETUP
config options.
Signed-off-by: Anshul Dalal <anshuld@ti.com>
To simplify the boot process and prevent the R5 SPL size from growing,
this patch restricts the boot media to load the next stage payload
(tifalcon.bin and kernel FIT) to MMC only.
We select between eMMC/SD by checking "mmcdev" in env to conform with
how U-Boot proper handles loading binaries from MMC1 or MMC2.
Note that tiboot3.bin (the initial bootloader) can be loaded from any
boot mode supported by the ROM since the restriction only applies to
tifalcon.bin and fitImage.
Signed-off-by: Anshul Dalal <anshuld@ti.com>
We use the spl_board_prepare_for_boot hook to call k3_r5_falcon_prep
which is ran after tispl is loaded but before jump_to_image.
In k3_r5_falcon_prep, we find the boot media and load the kernel FIT
just as standard secure falcon mode (since spl_start_uboot returns 0
now). Once the kernel and args are loaded.
Now when the flow goes to jump_to_image, we do the regular pre-jump
procedure and jump to TFA which jumps to the kernel directly since we
have already loaded the kernel and dtb at their respective addresses
(PRELOADED_BL33_BASE and K3_HW_CONFIG_BASE).
Overall execution for the R5 SPL after this patch:
board_init_r
|-> boot_from_devices
| +-> load_image (we load tifalcon.bin here since spl_start_uboot
| returns 1)
|
+-> spl_prepare_for_boot
| +-> k3_falcon_prep
| +-> load_image (we load fitImage here since spl_start_uboot
| returns 0 now)
|
+-> jump_to_image
Signed-off-by: Anshul Dalal <anshuld@ti.com>
This fragment enables falcon mode for K3 platforms and modifies the
memory map.
To have enough stack and heap space for loading kernel image as
FIT the memory map was modified by expanding stack + heap size, the
PRELOADED_BL33_BASE in TFA has to also be updated to 0x82000000 since
the kernel needs to be loaded at 2MiB aligned address along with
updating K3_HW_CONFIG_BASE to 0x88000000 for the DT passed to kernel.
Modified memory map for R5 SPL (modified addresses marked with *):
0x80000000 +-------------------------------+ Start of DDR
512KiB | TFA reserved memory space | CONFIG_K3_ATF_LOAD_ADDR*
0x80080000 +-------------------------------+
31.5MiB | Unused |
0x82000000 +-------------------------------+ PRELOADED_BL33_BASE* in TFA
| | CONFIG_SYS_LOAD_ADDR*
57MiB | Kernel + initramfs Image | CONFIG_SPL_LOAD_FIT_ADDRESS*
| |
0x85900000 +-------------------------------+
| |
| R5 U-Boot SPL Stack + Heap |
39MiB | (size defined by |
|SPL_STACK_R_MALLOC_SIMPLE_LEN*)|
| |
0x88000000 +-------------------------------+ CONFIG_SPL_STACK_R_ADDR*
| | K3_HW_CONFIG_BASE* in TFA
16MiB | Kernel DTB | CONFIG_SPL_PAYLOAD_ARGS_ADDR*
| |
0x89000000 +-------------------------------+
331MiB | Device Manager (DM) Load Addr |
0x9db00000 +-------------------------------+
12MiB | DM Reserved |
0x9e700000 +-------------------------------+
1MiB | Unused |
0x9e800000 +-------------------------------+ BL32_BASE in TFA
24MiB | OPTEE |
0xa0000000 +-------------------------------+ End of DDR (512MiB)
Signed-off-by: Anshul Dalal <anshuld@ti.com>
This patch adds creation of tifalcon.bin for the AM62a, 62p and 62x.
The contents are the same as the existing tispl.bin but A53's SPL and
the FDT have been removed as they are not needed in R5 falcon mode.
This reduces boot time since the payload size is smaller compared to the
regular tispl.bin.
tispl.bin = TFA + TEE + TIFS-STUB + A53 SPL + FDT
tifalcon.bin = TFA + TEE + TIFS-STUB
Signed-off-by: Anshul Dalal <anshuld@ti.com>
I have a hunch VPL_DM_SERIAL should not be selectable if VPL isn't set
as implied by the prefix. Additionally, still based on the prefix, I'm
assuming VPL_DM should be a dependency. Since VPL_DM can only be
selectable when VPL is enabled, only depend on VPL_DM.
This mirrors SPL_DM_SERIAL and TPL_DM_SERIAL so seems right to me.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
SPL_FIT_FULL_CHECK currently shares its description and help text with
FIT_FULL_CHECK which is quite confusing, so let's specify this applies
to SPL.
Fixes: 6f3c2d8aa5 ("image: Add an option to do a full check of the FIT")
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
This is mostly R-Car Gen5 drivers for GPIO, pin control, RSwitch3 and
matching PHYs. There is also a few trivial clean ups for arch headers
and configs. Board code, DT and clock are coming in follow up PR.
The type efi_status_t is not compatible with the return type int.
Let efi_store_memory_map() return -EFAULT instead of a truncated EFI error
code.
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Add extension_overlay_addr description to the list of environment
variables that can be useful during the standard boot.
Signed-off-by: Kory Maincent (TI.com) <kory.maincent@bootlin.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Now that extension support has been added to extlinux and efi bootmeths
we can remove this line from the TODO list.
Signed-off-by: Kory Maincent (TI.com) <kory.maincent@bootlin.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Currently, the EFI framebuffer is non-functional in payload mode. It
always reports: "No video mode configured in EFI!"
This is caused by a copy-paste error that replaced
"struct efi_entry_gopmode" with "struct efi_gop_mode".
Fixes: 88753816cf ("efi: video: Move payload code into a function")
Signed-off-by: Ben Wolsieffer <ben.wolsieffer@hefring.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Since C99 flexible array members are allowed at the end of structures.
We require C11.
Use struct efi_gop_mode_info in the definition of struct efi_entry_gopmode
to avoid code duplication and unnecessary conversions.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
On RISC-V QEMU provides an XSDT table. The RSDP table points to it.
We must not zero out this pointer because otherwise no ACPI table can be
found.
Fixes: 15ca25e31e ("x86: emulation: Support BLOBLIST_TABLES properly")
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Update the command to show the size and selected file, since this is
useful information at times. Add a heading so it is clear what each
field refers to.
Add a simple test as well.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Now that we've had jobs running on both amd64 and arm64 hosts for a
while, we have enough data to look at usage and findings. For the world
build job, make use of the new DEFAULT_FAST_TAG and only build it once,
on either amd64 or arm64 as we don't run in to host specific results
there. For sandbox, continue to build on both arm64 and amd64 hosts as
we can find host specific breakage that way. Remove the mistaken
restriction on sandbox64_lwip.
Signed-off-by: Tom Rini <trini@konsulko.com>
Dmitrii Sharshakov <d3dx12.xx@gmail.com> says:
I faced some minor compatibility issues when choosing Clang as the
cross-compiler for my target.
Please review these two fixes, aiming at enabling Clang-based builds
(still using GNU binutils) for 32-bit ARM targets.
Tested to fix build with (also run-tested on qemu arm and arm64 with clang):
make ARCH=arm HOSTCC=clang CROSS_COMPILE=arm-none-eabi- CC=clang imx6ulz_smm_m2b_defconfig
make ARCH=arm HOSTCC=clang CROSS_COMPILE=arm-none-eabi- CC=clang -j20
Link: https://lore.kernel.org/r/20251101-clang-fixes-v1-0-a8398475226e@gmail.com
The current default boot command does not respect the Linux kernel 2 MiB
alignment requirement, present on aarch64 [1]:
"
The Image must be placed text_offset bytes from a 2MB aligned base
address anywhere in usable system RAM and called there.
"
Adjust the boot command such, that it always places both Image and DT at
the nearest highest 2 MiB aligned offset. The DT is placed at lower 2 MiB
aligned address, the aarch64 Image is placed at the next higher 2 MiB
aligned address. Is is unlikely that a DT would be larger than 2 MiB on
these systems.
Replace use of hard-coded load addresses with generic ${loadaddr} aligned
using setexpr. This way, if user picks valid ${loadaddr}, their kernel and
DT address will be correctly set as well.
Fix up boot commands to use && instead of ; to exit the boot command early
in case of failure.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/arch/arm64/booting.rst#n138
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Use the BIT() macro consistently in R-Car Gen3 header.
Fix indent with spaces to tabs at the same time. No
functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Make CONFIG_SYS_LOAD_ADDR family-specific to prepare for R-Car Gen5
support. R-Car Gen5 uses different memory map compared to the current
R-Car Gen3 and Gen4 and also different CONFIG_SYS_LOAD_ADDR. This is
a preparatory change for R-Car Gen5. No functional change.
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> # Upport
Checkpatch warns that it's generally not useful to have
the filename in the file. The warning is valid, drop the
encoded file name. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add initial pin control tables for the Renesas R-Car X5H R8A78000 SoC.
This SoC is the first one which includes custom DRV register handling,
different from previous generations due to change in DRV register bit
layout.
Signed-off-by: Huy Bui <huy.bui.wm@renesas.com>
Signed-off-by: Khanh Le <khanh.le.xr@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The upcoming Renesas R-Car Gen5 uses different mapping of bits in DRV
control register, which is incompatible with existing DRV register bit
mapping. Add .set_drive_strength callback into sh_pfc_soc_operations
and call it from sh_pfc_pinconf_set(), to allow each SoC specific PFC
driver to implement replacement .set_drive_strength. Make the current
sh_pfc_pinconf_set_drive_strength() non-static, rename it with rcar_
prefix, and pass it as .set_drive_strength for existing PFC drivers.
This is a preparatory patch for R-Car Gen5, no functional change.
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Consistently use .set_drive_strength() and pass exisiting
sh_pfc_pinconf_set_drive_strength() as its parameter for
all PFC drivers. Rewrite commit message.]
Show bit position in config write debug log, which is helpful for cases
where the p port setting is applied at the exact p bit position.
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> # Unsplit the string
Fix Kconfig entry indent to be always consistently indented with
leading tabs, never with leading spaces. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add support for the GPIO controller block in the R-Car Gen5 SoC family.
The GPIO controller has a General Input Enable Register (INEN), whose
reset state is to have all input disabled. The GPIO controller also has
updated offsets for its control registers. U-Boot uses three registers,
INDT, POSNEG, INEN, which have updated offsets, those are handled by the
driver.
Signed-off-by: Huy Bui <huy.bui.wm@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: - Access Gen5 specific registers via driver data offsets,
- Update commit message]
The Renesas R-Car Gen5 GPIO controller has INDT, POSNEG, INEN registers
at different offsets compared to previous generations. Introduce three
new entries in struct rcar_gpio_data {} match data to describe these
register offsets for each GPIO controller. Update the driver to access
these three registers through the match data offsets. No functional
change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Wrap the RCAR_GPIO_HAS_INEN quirk in more flexible struct rcar_gpio_data {}
in preparation for addition of Renesas R-Car Gen5 GPIO controller support.
The Renesas R-Car Gen5 GPIO controller requires more than a single quirk
to properly describe it, therefore increase the flexibility and introduce
full match data structure, and use it throughout the driver. No functional
change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Remove register macros for registers which are not used by this driver.
This makes it easier to get an overview of which registers are really
used by the driver. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The PFC offset is no longer used directly in the driver since commit
fbf26bea39 ("gpio: renesas: Migrate to pinctrl GPIO accessors")
Drop the pfc_offset parsing.
Fixes: fbf26bea39 ("gpio: renesas: Migrate to pinctrl GPIO accessors")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add PHY driver for Multi-Protocol PHY present on Renesas R-Car X5H
R8A78000 SoC. Currently, the PHY driver only supports configuring
the MPPHY for ethernet operation.
Signed-off-by: Thanh Quan <thanh.quan.xn@renesas.com>
Signed-off-by: Phong Hoang <phong.hoang.wz@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> #Fix License-Identifier
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Clean up macros, indent, clock and reset handling in probe,
rename the driver and add r8a78000- into compatible string,
update commit message.]
Add support for the Ethernet Physical Coding Sublayer (PCS) controller
on R-Car Gen5 SoCs, specifically the Renesas R-Car X5H R8A78000.
The controller is based on the SERDES infrastructure used in previous
R-Car generations, with updates for Gen5 register layout and features.
Because majority of this driver is SoC-specific register programming,
the majority of this driver is different enough from R8A779F0 SerDes
driver to justify its own driver. Deduplication of the remaining bits
of code does not yield any improvement.
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Phong Hoang <phong.hoang.wz@renesas.com>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Thanh Quan <thanh.quan.xn@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Add missing clk_bulk_disable() in fail path.
Drop always-true aneg_on setting.
Reduce poll delay from 100s to 100ms.
Use bulk reset operations to finalize reset handling.]
Add support for the Renesas Ethernet Switch3 (RSW3) controller,
present in R-Car Gen5 SoCs such as R-Car X5H (R8A78000). The
hardware offset differences are handled via driver match data.
The driver newly detects whether the switch prot is connected
to xPCS or not, and if so, turns on MIOC bit 3. This is new on
R-Car X5H. GWCKSC register is also programmed only on X5H. The
rest of the operation is identical to RSwitch2.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Phong Hoang <phong.hoang.wz@renesas.com>
Signed-off-by: Thanh Quan <thanh.quan.xn@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
The MPIC_MDC_CLK clock setting value differs between R-Car S4
and R-Car X5H. Parametrize the value in preparation for R-Car
X5H addition into this driver. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The GWDCBAC0, GWDCBAC1, FWPBFCSDC, CABPIRM register offsets changed
between R-Car S4 and R-Car X5H. Parametrize their offsets in preparation
for R-Car X5H addition into this driver. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Inline FWRO, CARO, GWRO, TARO, RMRO macros directly into the
follow up register macros. FWRO, CARO, GWRO, TARO are already
zero, drop them. RMRO is 0x1000, increment all registers which
add RMRO by 0x1000 directly. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The forwarding engine CSD register offset changed between the
R-Car S4 and R-Car X5H. Parametrize this offset in preparation
for R-Car X5H addition into this driver. Clean up the macro
parameter names and make them more obvious. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The total port counts differ across variants of this IP in
R-Car S4 and R-Car X5H. Parametrize port count in preparation
for R-Car X5H addition into this driver. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The COMA, ETHA, GWCA offsets differ across variants of this IP in
R-Car S4 and R-Car X5H. Parametrize these offsets in preparation
for R-Car X5H addition into this driver. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
This IP does support operating MII and SerDes via different ports.
Currently, the driver assumes that MII and SerDes are always bound
together on the same port, but this may not be the case. Implement
support for controlling MII and SerDes separately.
While the change is extensive, the gist of the change is to pass
pointer to the selected port registers to MII or SerDes functions,
depending on which port and operations should be done on that port.
Each combined ETHA instance contains both MII and SerDes register
pointers, which may not point to the same port, and passes those
registers to MII and SerDes functions respectively to control the
MII or SerDes of each port.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The new version of RSwitch3 in Renesas R-Car Gen5 uses multiple
clock to supply the IP. Convert the driver to bulk clock API to
cater for both single clock of R-Car S4 and multiple clock of
R-Car Gen5. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Empty RX DMA descriptor must contain .die_dt field set to DT_FEMPTY,
because hardware DMA overwrites this field to non-DT_FEMPTY when data
are received, and the .recv callback tests the content of RX descriptor
.die_dt field to determine whether hardware did receive any data and
updated the .die_dt field, and based on that information, receives a
packet or not. Fix the incorrect RX DMA descriptor initialization to
assure the .recv callback always works correctly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Fix indent from multiple spaces to tabs, to be consistent with
coding style and the rest of the driver. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add support for jumping to Linux kernel through OPTEE-OS on ARMv7a to SPL.
This is already supported on ARMv8a, this patch adds the ARMv7a support.
Extend the SPL fitImage loader to record OPTEE-OS load address and in case
the load address is non-zero, use the same bootm-optee.S code used by the
U-Boot fitImage jump code to start OPTEE-OS first and jump to Linux next.
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Add support for jumping to Linux kernel through OPTEE-OS on ARMv7a.
This is only supported if U-Boot runs in PL1 secure. This change adds
two components, one is fitImage OPTEE-OS loadable handler, which makes
a note of OPTEE-OS being loaded and stores the load address for later
jump to it. The second part is the actual jump to Linux through OPTEE-OS.
The jump through OPTEE-OS requires set up of multiple CPU registers, r1
and r2 are passed through, r0 and r3 have to be set to 0, lr is set to
Linux kernel entry point. This setup is done by new assembler function
boot_jump_linux_via_optee().
The boot_jump_linux_via_optee() also includes STM32MP13xx late TZC
configuration write, this cannot be moved easily, hence the ifdef.
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Make sure to pass Clang flags to the KBUILD_CPPFLAGS as well, as this
variable is used for flags during compiling for target
Skipping this leads to Clang being invoked with args for target, but
without target indication, thus defaulting to host arch:
LDS u-boot.lds
clang: error: ... '-mabi=' for target 'x86_64-suse-linux'
clang: error: ... '-mno-thumb' for target 'x86_64-suse-linux'
clang: error: ... '-mno-unaligned-access' for target 'x86_64-suse-linux'
clang: error: ... '-ffixed-r9' for target 'x86_64-suse-linux'
clang: error: ... '-mno-movt' for target 'x86_64-suse-linux'
make: *** [Makefile:2345: u-boot.lds] Fehler 1
Signed-off-by: Dmitrii Sharshakov <d3dx12.xx@gmail.com>
This option is not available for 32-bit ARM targets and causes an error
when building with Clang:
clang: error: unsupported option '-mgeneral-regs-only' for
target 'arm-none-eabi'
This fixes the following patch (also seems to only concern AArch64):
Link: https://lists.denx.de/pipermail/u-boot/2021-August/458067.html
Signed-off-by: Dmitrii Sharshakov <d3dx12.xx@gmail.com>
When spl boot device list has multiple FAT devices, any previousely
registered FAT device should be deregistered before registering
next FAT boot device, otherwise the function may not attempt boot
from next FAT device.One of the situations where this issue can be
observed is when the boot device list has two FAT partitions of a
memory device and if booting fails on first partition (because of
file or partition related errors), boot from next partition actually
gets attempted on previous boot device only, as the previous device
has remained marked as registered. Call the function that invalidates
cached boot device in case of failure in booting from current FAT
boot device.
Signed-off-by: Prasad Kale <prasad.kale@live.com>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Sean Anderson <seanga2@gmail.com>
Align the implementation to rsa_add_verify_data() by writing the modulus
and r-squared properties with the same length as the key itself. This
fixes signature verification issues when one of the parameters has
leading zeros.
Reported-by: Hans Gfirtner (Nokia) <hans.gfirtner@nokia.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Technically, commit 24bf44cf88 ("spl: fit: Do not fail immediately if
an overlay is not available") introduced that regression as the code
will never advance if spl_fit_get_image_name() will return an error. But
at that time, spl_fit_get_image_node() was used in spl_fit_append_fdt()
which calls fdt_subnode_offset() to get the image node. And I presume
the commit was about the latter failing gracefully and trying the next
one.
But with commit b13eaf3bb4 ("spl: fit: Add board level function to
decide application of DTO") that behavior changed and the loop in
spl_fit_append_fdt() no longer uses spl_fit_get_image_node() but
spl_fit_get_image_name() directly. Thus it doesn't make any sense to not
break the loop if that fails.
Also, the original use case of commit 24bf44cf88 ("spl: fit: Do not
fail immediately if an overlay is not available") is preserved because
spl_subnode_offset() is now called within the loop and errors are
handled gracefully (and advancing the index).
Fixes: b13eaf3bb4 ("spl: fit: Add board level function to decide application of DTO")
Signed-off-by: Michael Walle <mwalle@kernel.org>
In Azure, older pipelines such as ours do not default to a shallow fetch
but rather do a complete clone. This introduces a marginal time increase
in each task, but also more importantly takes up significant disk space.
We are now getting warnings in some cases about using more than 95% of
our available disk space so take this as a first easy step to resolve
that problem.
Signed-off-by: Tom Rini <trini@konsulko.com>
Rockchip boards may depend on a working MMC regulator in SPL to
successfully load FIT payload from MMC. Typically, these boards only
include the vmmc-supply regulator and not its vin-supply in SPL control
FDT.
The commit f98d812e53 ("power: regulator: Add vin-supply for GPIO and
Fixed regulators") breaks loading FIT from MMC in SPL on some of these
boards due to now requiring the vin-supply to be included in the SPL
control FDT.
The commit also strangely enables any found vin-supply in
regulator_common_of_to_plat() and not when a regulator is enabled or as
part of regulator_autoset().
Revert the commit to fix FIT loading in SPL on broken boards.
If a board needs to have its vin-supply enabled, two options come to
mind:
- Add regulator-always-on prop to the regulator in the -u-boot.dtsi for
any board.
- Implement full support for reference counting of regulators and then
update the regulator-uclass to enable any found vin-supply when a
regulator is enabled.
This reverts commit f98d812e53.
Reported-by: Dang Huynh <danct12@riseup.net>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
If CONFIG_GPIO_HOG is not set, then gpio_hog_lookup_name() is empty,
and thus does not initialize any of its parameters. It does still
return 0 though, and so any calling function might assume that the
parameters have been initialized successfully.
Change the return value to -ENODEV in this case, as the function
would in the case when CONFIG_GPIO_HOG is set but the gpio hog
could not be found.
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Heiko Schocher <hs@nabladev.com>
In devices where the U-Boot is used as a secondary bootloader, we rely
on the device's primary bootloader to implement CNTFRQ_EL0. However,
this reliance may lead to a non-functional timer in broken firmware.
For instance, some versions of Samsung's S-Boot don't implement it. It's
also not possible to set it in the U-Boot, because it's booted in a lower
exception level. CNTFRQ_EL0 is reported to be 0.
Use gd->arch.timer_rate_hz to override the queried value if set. This
setting needs to be done in the board file, preferrably in timer_init().
This feature is present only when the CONFIG_ARMV8_CNTFRQ_BROKEN is
enabled.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Introduces support for Device Firmware Upgrade (DFU) over PCIe in
U-Boot. Traditionally, the DFU protocol is used over USB, where a
device enters DFU mode and allows a host to upload firmware or binary
images directly via the USB interface. This is a widely adopted and
convenient method for updating firmware.
In the context of Texas Instruments (TI) SoCs, PCIe can be used as a
boot interface in a manner that differs from the conventional
"PCIe Boot" process, which typically refers to booting an OS or
firmware image from an NVMe SSD or other PCIe-attached storage devices.
Instead, TI SoCs can be configured as a PCIe Endpoint, allowing a
connected PCIe Root Complex (host) to transfer images directly into the
device’s memory over the PCIe bus for boot purposes. This mechanism is
analogous to DFU over USB, but leverages the high-speed PCIe link and
does not depend on traditional storage devices.
By extending the DFU framework in U-Boot to support PCIe, it will be
possible to flash images over PCIe. While this implementation is
motivated by TI SoC use cases, the framework is generic and can be
adopted by everyone for platforms that support PCIe Endpoint mode.
Platforms with hardware support for PCIe-based memory loading can use
this to implement PCIe as a boot mode, as well as to enable flashing
and recovery scenarios similar to DFU over USB.
In summary, enable support for:
- DFU-style flashing of firmware/images over PCIe, analogous to existing
USB DFU workflows
- PCIe as a boot mode where a host can load images directly into device
memory using DFU over PCIe
Signed-off-by: Hrushikesh Salunke <h-salunke@ti.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Link: https://lore.kernel.org/r/20251023080922.3527052-1-h-salunke@ti.com
Signed-off-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Now that we have a test for QEMU using transfer list from the previous
stage, there are two platforms testing this particular infrastructure. A
problem with the vexpress_fvp platform emulation in Gitlab is that we
often run it on hosts that are fast enough that we run in to a race
condition when trying to acquire the console and the test fails. Remove
both vexpress_fvp tests from Gitlab (they can remain in Azure) to remove
these spurious failures.
Signed-off-by: Tom Rini <trini@konsulko.com>
This also incorporates the following commits to the Dockerfile:
da7942de29 Dockerfile: remove Python 2.7
183299d9a4 docker: add OP-TEE and TF-A build for testing Firmware Handoff
Signed-off-by: Tom Rini <trini@konsulko.com>
Add qemu_arm64_tfa_fw_handoff test entries to azure and gitlab
pipelines.
Signed-off-by: Raymond Mao <raymond.mao@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Check the existence of bl1 and fip from:
1. /opt/tf-a/${board_type}_${board_ident}, if not exist, then;
2. /opt/tf-a/${board_type}
This change allows to test with TF-A with specified board ID only.
Signed-off-by: Raymond Mao <raymond.mao@linaro.org>
Firmware Handoff tests will leverage the same board type 'qemu_arm64'
with a new board ID 'fw_handoff_tfa_optee', thus select CMD_BLOBLIST
in qemu_arm64_defconfig for running the test.
Signed-off-by: Raymond Mao <raymond.mao@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add test cases to validate FDT and TPM eventlog handoff from TF-A
and OP-TEE via bloblist.
For FDT, the nodes 'reserved-memory' and 'firmware' appended by
OP-TEE indicates a successful handoff.
For TPM eventlog, the events 'SECURE_RT_EL3', 'SECURE_RT_EL1_OPTEE'
and 'SECURE_RT_EL1_OPTEE_EXTRA1' created by TF-A indicates a
successful handoff.
Signed-off-by: Raymond Mao <raymond.mao@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Fetch OP-TEE (4.7.0), TF-A (v2.13.0), MbedTLS (v3.6) and build
bl1 and fip with both Firmware Handoff and Measured Boot enabled.
Signed-off-by: Raymond Mao <raymond.mao@linaro.org>
Acked-by: Jerome Forissier <jerome.forissier@linaro.org>
mem_map_from_dram_banks calls fdtdec_setup_memory_banksize to setup the
dram banks though that is expected to be done by dram_init_banksize as
part of board_r sequence.
This has the side effect of modifying gd->bd->bi_dram as well, therefore
this patch removes the call and updates spl_enable_cache for K3 to call
dram_init_banksize.
Signed-off-by: Anshul Dalal <anshuld@ti.com>
Reported-by: Francesco Dolcini <francesco@dolcini.it>
Closes: https://lore.kernel.org/u-boot/20251027165225.GA71553@francesco-nb/
Fixes: fe2647f2a0 ("arm: armv8: mmu: add mem_map_from_dram_banks")
Tested-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Add boot support and peripherals like eMMC/SD, UART, I2C, GPIO, ENETC0/1
and PCIE0/1 for iMX95 15x15 LPDDR4X EVK.
Updated doc for build instructions.
Signed-off-by: Ye Li <ye.li@nxp.com>
Add -u-boot.dtsi for iMX95 15x15 EVK used by SPL and binman.
iMX95 15x15 EVK uses LPDDR4X which needs dedicated DDR FW.
Signed-off-by: Ye Li <ye.li@nxp.com>
The factory provides a CPU UID in the OTPs and the SoM module
and the carrier board might provide additional UIDs in the GP
registers of the OTPs. Load these values in the following order
and create a serial number string:
* Board UID (GP2)
* SoM UID (GP1)
* CPU UID (UNIQUE_ID)
The string is stored in the "serial#" env variable and
exported to Linux. Further this prints the used UID to the
console which looks like this
ID: 0042152331 (Board)
or:
ID: 0030124840 (SoM)
or:
ID: 4696668CD9516886 (CPU)
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
The factory provides a CPU UID in the OTPs and the SoM module
and the carrier board might provide additional UIDs in the GP
registers of the OTPs. Load these values in the following order
and create a serial number string:
* Board UID (GP2)
* SoM UID (GP1)
* CPU UID (UNIQUE_ID)
The string is stored in the "serial#" env variable and
exported to Linux. Further this prints the used UID to the
console which looks like this
ID: 0042152331 (Board)
or:
ID: 0030124840 (SoM)
or:
ID: 4696668CD9516886 (CPU)
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
The factory provides a CPU UID in the OTPs and the SoM module
and the carrier board might provide additional UIDs in the GP
registers of the OTPs.
Provide a common function to load UIDs from arbitrary OTP
registers and generate a serial number string that is saved
in the "serial#" env variable.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Recently code was added in board_late_init() to autostart fastboot
in case of booting from USB OTG. This change was ineffective as
enabling CONFIG_BOARD_LATE_INIT got lost during upstreaming.
Fixes: 410d9ccc03 ("imx: kontron-sl-mx6ul: Autostart fastboot if booted from USB")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
This allows to print user-friendly names for the boot device
probed by SPL to the console.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
The image offset on SD/MMC devices is 33 KiB, except for eMMC boot if
fastboot is enabled. In this case it is 1 KiB. In order to make the
the bootloader universal, check the fastboot OTP boot fuse and adjust
the offset.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Add guide on how to use the Remote Processors on i.MX8M and i.MX93.
Update MAINTAINERS to include doc/board/nxp.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Introduce remote processor configuration for the i.MX93 Cortex-M33 core.
This patch adds:
- Address translation table (ATT) for i.MX93, including TCM
(secure and non-secure) and DDR regions.
- A new device configuration structure `imx_rproc_cfg_imx93` using SMC
method and ARM SMC ops.
- Device tree match entry for "fsl,imx93-cm33"
This enables remoteproc framework to properly initialize and manage the
Cortex-M33 core on i.MX93 platforms.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX8MQ/M use MMIO based method to directly configure SRC registers
to start/stop M4.
Add mmio ops to start/stop/is_running.
Add i.MX8MQ cfg data, i.MX8MN reuses i.MX8MQ data.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Support i.MX8MP/N with start/stop/device_to_virt/is_running/load
implemented. The device static configuration is mostly reused from
Linux Kernel with adapation to U-Boot dm_rproc_ops.
The booting method:
- load mmc 2:2 0x90000000 /lib/firmware/imx8mp_m7_DDR_rpmsg_lite_str_echo_
rtos.elf
- rproc load 0 0x90000000 ${filesize}
- rproc start 0
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Some areas needs to be initialized by using memcpy_toio and memset_io.
Following Linux Kernel commit: 40df0a91b2a5 ("remoteproc: add is_iomem to
da_to_va"), add this to U-Boot.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The LED enumerators are missing, which prevents the LEDs from being
accurately told apart by label. Fill in the enumerators the same way
they are already present on PDK3. Put this into local DT extras until
matching kernel patch lands in Linux.
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This patch splits the 2MB SRAM0 mapping into three regions:
- 0x22000000~0x2201f000: cacheable normal memory
- 0x2201f000~0x22020000: non-cacheable device memory
- 0x22020000~0x22200000: cacheable normal memory
The change ensures the SCMI shared memory is non-cacheable, which
avoids cache-related issues after removing
mmu_set_region_dcache_behaviour() from scmi_dt_get_smt_buffer().
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Reviewed-by: Marek Vasut <marek.vasut@mailbox.org>
Enable DFU SF on all i.MX6 DHSOM so the SPI NOR can be exposed via
DFU, and include dfu_alt_info which exposes the full SPI NOR via DFU.
To install new bootloader into the SPI NOR using DFU, it is necessary
to pad the u-boot-with-spl.imx to 0x400 Bytes offset first and then
send it to the board as follows:
"
u-boot=> dfu 0 sf
"
"
host$ dd if=/dev/zero of=pad.bin bs=1024 count=1
host$ cat pad.bin u-boot-with-spl.imx > flash.bin
host$ dfu-util -w -a 0 -D flash.bin
"
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
USB OS Descriptors are used to install and configure the device without
requiring any user interaction on OS which support them (e.g. Windows).
Enable them in order to improve the user experience when fastboot is used.
Fixes: ff0540fcfe ("board: toradex: add Toradex SMARC iMX95")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Improve support for the BSH SystemMaster (SMM) M2B board.
In particular, this patch adds the timing for the 512 MB version, and
the spi.c reflects it by removing the safe guards.
Signed-off-by: Andrea Calabrese <andrea.calabrese@amarulasolutions.com>
With this patch, both ENETC1 and ENETC2 are functional on the i.MX943
EVK board and can be used for networking.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Add support for the optional 'phy-supply' property in the ENETC MDIO
driver. This allows the driver to enable and manage the PHY's power
supply via the regulator framework when specified in device tree.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
This patch adds SPL Kconfig option (SPL_PHY_IMX8MQ_USB) for the i.MX8MQ,
i.MX8MP, i.MX95, and i.MX94 USB3.0 PHY driver, allowing the driver to be
compiled and probed in SPL stage.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
After update this, uuu(>1.6) can use below command to filter out devices
when multi boards connected.
uuu -ms <serial#> ...
[sudo] uuu -lsusb can list known devices with serial# informaiton.
Serial number is retrieved via get_board_serial() and passed to
g_dnl_set_serialnumber(). This part is conditionally compiled for i.MX94
only now.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
This patch enables the USB 2.0 controller to operate in host mode on the
i.MX943 EVK board. It updates the device tree files to configure the USB
2.0 controller appropriately and modifies the defconfig to include
necessary support.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Add USB1_BASE_ADDR and USB2_BASE_ADDR for i.MX9 platform, and define
USB_BASE_ADDR as an alias to USB2_BASE_ADDR.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Since the EHCI USB driver is shared across i.MX91, i.MX93, i.MX94, and
i.MX95, the condition check is updated to use IMX9.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Reviewed-by: Marek Vasut <marek.vasut@mailbox.org>
If OF_CONTROL is on, ti-musb.c registers a "ti-musb-wrapper" driver
that requires UCLASS_MISC. Hence, select MISC if both OF_CONTROL
and USB_MUSB_TI are selected.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Anshul Dalal <anshuld@ti.com> says:
With the addition of secure falcon mode since commit 7674ac9c82 ("Merge patch
series "Add support for secure falcon mode: disable args file""), this series now
adds support for the same to TI's K3 devices and documents the feature taking
AM62x EVM as an example.
With secure falcon mode from A-Core SPL, the boot flow changes as follows:
Existing:
R5 SPL -> TFA -> OP-TEE -> A-Core SPL -> *U-Boot* -> Linux Kernel
Modified:
R5 SPL -> TFA -> OP-TEE -> A-Core SPL -> Linux Kernel
Link: https://lore.kernel.org/r/20251024081408.1610102-1-anshuld@ti.com
Anshul Dalal <anshuld@ti.com> says:
Hi all,
We currently make use of CMD_BOOTI and CMD_BOOTZ in the SPL boot flow in
falcon mode, this isn't correct since all CMD_* configs are only meant
for U-Boot proper and not the SPL.
Therefore this patch set adds new LIB_BOOT[IMZ] configs that allow for
more granular selection of their respective compilation targets.
Additionally, this also allows us to more easily disable support for
raw images from secure falcon mode (SPL_OS_BOOT_SECURE) by doing the
following:
config LIB_SPL_BOOTI
...
depends on SPL_OS_BOOT && !SPL_OS_BOOT_SECURE
...
Link: https://lore.kernel.org/r/20251027-fix_cmd_bootx-v10-0-10487e907710@ti.com
This patch documents the newly added SPL_OS_BOOT_SECURE option that
enables authenticated boot in falcon mode.
The document provides steps for using secure falcon mode on ARM64 taking
TI's AM62x EVM as an example.
Signed-off-by: Anshul Dalal <anshuld@ti.com>
With CONFIG_SPL_OS_BOOT enabled, U-Boot checks for the return value of
spl_start_uboot to select between falcon or the regular boot flow. Where
a return value of 0 means 'boot to linux'.
This patch overrides the weak definition form common/spl/spl.c to allow
K3 devices to use falcon mode with SPL_OS_BOOT_SECURE enabled for the
A-Core SPL.
Signed-off-by: Anshul Dalal <anshuld@ti.com>
Falcon mode was disabled for TI_SECURE_DEVICE at commit e95b9b4437
("ti_armv7_common: Disable Falcon Mode on HS devices") for older 32-bit
HS devices and but can now be enabled with the addition of
OS_BOOT_SECURE.
For secure boot, the kernel with x509 headers can be packaged in a fit
container (fitImage) signed with TIFS keys for authentication.
Signed-off-by: Anshul Dalal <anshuld@ti.com>
Anshul Dalal <anshuld@ti.com> says:
Hi all,
We currently make use of CMD_BOOTI and CMD_BOOTZ in the SPL boot flow in
falcon mode, this isn't correct since all CMD_* configs are only meant
for U-Boot proper and not the SPL.
Therefore this patch set adds new LIB_BOOT[IMZ] configs that allow for
more granular selection of their respective compilation targets.
Additionally, this also allows us to more easily disable support for
raw images from secure falcon mode (SPL_OS_BOOT_SECURE) by doing the
following:
config LIB_SPL_BOOTI
...
depends on SPL_OS_BOOT && !SPL_OS_BOOT_SECURE
...
Link: https://lore.kernel.org/r/20251027-fix_cmd_bootx-v10-0-10487e907710@ti.com
In the existing behaviour, CMD_BOOTZ is not enabled by default which
means zimage.o is not compiled in the SPL in falcon mode unless
explicitly enabled. This changes now as SPL_BOOTZ is default y for
falcon users which leads to larger SPL size with zimage.o being present.
This patch modifies the defconfigs that used falcon mode but don't
require zimage support.
Signed-off-by: Anshul Dalal <anshuld@ti.com>
Using CMD_* configs from spl doesn't make logical sense. Therefore
this patch replaces the checks for CMD_BOOTx with newly added library
symbols LIB_BOOT[IMZ] and SPL_LIB_BOOT[IMZ] which are enabled by their
respective CMD_* or SPL_* counterparts.
On platforms with non-secure falcon mode, SPL_BOOTZ is enabled by
default for 32-bit ARM systems and SPL_BOOTI is enabled by default for
64-bit ARM and RISCV.
The respective C files (image.c/zimage.c) are compiled based on library
symbols $(PHASE_)LIB_BOOTx instead which are in turn selected by both
CMD_BOOTx and SPL_BOOTx as required.
Signed-off-by: Anshul Dalal <anshuld@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Kory Maincent (TI.com) <kory.maincent@bootlin.com> says:
This series converts the extension board framework to use UCLASS as
requested by Simon Glass, then adds extension support to pxe_utils
and bootmeth_efi (not tested) to enable extension boards devicetree load
in the standard boot process.
I can't test the imx8 extension scan enabled by the
imx8mm-cl-iot-gate_defconfig as I don't have this board.
I also can't test the efi bootmeth change as I don't have such board.
Link: https://lore.kernel.org/r/20251030-feature_sysboot_extension_board-v5-0-cfb77672fc68@bootlin.com
Add support for scanning and applying extension board devicetree
overlays during EFI boot. After loading the main board devicetree,
the system now scans for available extension boards and applies their
overlays automatically.
Signed-off-by: Kory Maincent (TI.com) <kory.maincent@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Simplify the return path in distro_efi_try_bootflow_files() to prepare
for adding extension board support in a subsequent commit.
Signed-off-by: Kory Maincent (TI.com) <kory.maincent@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for scanning and applying extension board devicetree
overlays during PXE boot. After loading the main board devicetree,
the system now scans for available extension boards and applies their
overlays automatically.
This enables dynamic hardware configuration for systems with extension
boards during boot scenarios which are using pxe_utils.
Signed-off-by: Kory Maincent (TI.com) <kory.maincent@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The extension_overlay_cmd environment variable approach is specific to
the U-Boot extension_board command, while other boot flows (pxe_utils,
bootstd) handle overlay loading differently.
Move the extension_overlay_cmd execution out of the core extension
framework to the command level. This decouples the framework from
command-specific behavior and prepares for future extension support
in other boot flows.
Signed-off-by: Kory Maincent (TI.com) <kory.maincent@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove the legacy extension board implementation now that all boards
have been converted to use the new UCLASS-based framework. This
eliminates lines of legacy code while preserving functionality
through the modern driver model approach.
Update the bootstd tests, due to the removal of extension hunter.
Signed-off-by: Kory Maincent (TI.com) <kory.maincent@bootlin.com>
Migrate sandbox extension board detection from legacy implementation to
the new UCLASS-based extension board framework.
Signed-off-by: Kory Maincent (TI.com) <kory.maincent@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enhance the extension board scanning code in sandbox with better error
handling and code organization.
Signed-off-by: Kory Maincent (TI.com) <kory.maincent@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Migrate sunxi board extension detection from legacy implementation to
the new UCLASS-based extension board framework.
Signed-off-by: Kory Maincent (TI.com) <kory.maincent@bootlin.com>
Clean up and improve code structure in the sunxi CHIP board extension
detection implementation.
Signed-off-by: Kory Maincent (TI.com) <kory.maincent@bootlin.com>
Migrate TI board cape detection from legacy extension support to the
new UCLASS-based extension board framework.
Signed-off-by: Kory Maincent (TI.com) <kory.maincent@bootlin.com>
Clean up and reorganize cape detection code structure for improved
maintainability and readability.
Signed-off-by: Kory Maincent (TI.com) <kory.maincent@bootlin.com>
Introduce UCLASS-based extension board support to enable more
standardized and automatic loading of extension board device tree
overlays in preparation for integration with bootstd and pxe_utils.
Several #if CONFIG_IS_ENABLED are used in cmd/extension_board.c to ease the
development but don't worry they are removed later in the series.
Signed-off-by: Kory Maincent (TI.com) <kory.maincent@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Relocate extension board support from cmd/ to boot/ directory in
preparation for converting the extension framework to use UCLASS.
Also improve code style by applying reverse xmas tree ordering.
Signed-off-by: Kory Maincent (TI.com) <kory.maincent@bootlin.com>
Disable compulab extension board detection functionality in XPL (eXtended
Program Loader) images to reduce size and complexity in the early boot
stage.
Signed-off-by: Kory Maincent (TI.com) <kory.maincent@bootlin.com>
Disable DIP detection functionality in XPL (eXtended Program Loader)
images to reduce size and complexity in the early boot stage.
Signed-off-by: Kory Maincent (TI.com) <kory.maincent@bootlin.com>
The CAPE_EEPROM_BUS_NUM configuration option was incorrectly depending
on CMD_EXTENSION, which represents the extension board command. However,
the cape scan functionality can be built and used independently of the
command interface through the SUPPORT_EXTENSION_SCAN option.
Change the dependency from CMD_EXTENSION to SUPPORT_EXTENSION_SCAN to
properly reflect that the I2C bus configuration is needed for the cape
scan function itself, not specifically for the command.
Signed-off-by: Kory Maincent (TI.com) <kory.maincent@bootlin.com>
Disable cape detection functionality in xPL images to reduce size and
complexity in the early boot stage.
Signed-off-by: Kory Maincent (TI.com) <kory.maincent@bootlin.com>
Add myself as maintainer for the extension board support that was
originally added to track ongoing development and maintenance.
Signed-off-by: Kory Maincent (TI.com) <kory.maincent@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
eMMC erase and write support on RK3528 is somewhat unreliable, sometime
e.g. mmc erase and write commands will fail with an error.
Use the delay line lock value for half card clock cycle, DLL_LOCK_VALUE,
to set a manual xx_TAP_VALUE to fix the unreliable eMMC support.
This is only enabled for RK3528, remaining SoCs still use the automatic
tap value, (DLL_LOCK_VALUE * 2) % 256, same value we configure manually
for RK3528.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Ensure that the spi/sfc node for SPI flash is aviliable during pre-reloc
phase so that env can successfully be loaded from SPI Flash.
No boards with these SoCs seem to be affected as there is no default use
of ENV_IS_IN_SPI_FLASH=y.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Boot devices are being probed when SPL boot order is determined. This
may delay boot slightly and can prevent booting from SPI Flash on boards
that use same pins for SPI Flash and eMMC due to pinctrl being applied
prior to booting.
Instead defer probe of the boot device until SPL try to load image from
the boot device by using uclass_find_device_by_of_offset() instead of
the get variant.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Add support for MNT Reform2, it works as a carrier board
with a Firefly iCore-3588Q SoM.
Specification:
- Rockchip RK3588
- LPDDR5X 16/32 GB
- eMMC 128/256 GB
- HDMI Type A out x 1
- USB 3.0 Host x 1
- USB-C 3.0 with DisplayPort AltMode
- PCIE M.2 E Key for Wireless connection
- PCIE M.2 M Key for NVME connection
- DSI to eDP panel
- 1Gb Ethernet w/ Microchip KSZ9310 PHY
Tested using Fedora boot on USB stick and eMMC.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Anbernic RG353M is hardware compatible with RG353P. Only the form-factor
differs. So only one DTS is created for both machines with
"Anbernic RG353P" as default model. If a RG353M is detected, the model
should be overwritten with the correct name.
Actually, it's overwritten with "Anbernic" only making the process of
machine detection a little harder.
However, to determine the size of the string "Anbernic RG353M", it is
sizeof() which is used resulting in obtaining the size of the pointer
(which is 8 bytes on ARM64) not the size of the pointed string.
strlen() should be used instead.
Signed-off-by: David Barbion <davidb@230ruedubac.fr>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Forcing all those symbols on means we cannot make the binary smaller or
with unnecessary features or drivers disabled. This is especially useful
for security, auditing and certification where less code built means
less to look at (and less surface attack) and less to patch, but also
for making binary images smaller which typically means faster boot.
It is possible to have boards without MMC, NAND or SPI flashes, without
anything on SPI or I2C buses, nothing to control over PWM or GPIO or for
which we have no interest in regulator control or serial output so make
it possible to remove all that if desired.
No intended change in default selected symbols.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit 65e2c14d5a ("binman: btool: mkimage: use Bintool.version")
removed the version argument from the run method but forgot to remove it
from the method docstring, so let's fix this oversight.
Fixes: 65e2c14d5a ("binman: btool: mkimage: use Bintool.version")
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The free running mode is 0 at bit offset 1. User mode is 1 at bit offset
1. Currently, free running mode is 1 at offset 0, which is already the
case thanks to TIME_EN.
So, this essentially does not change the actual value written to the
register as it is TIME_EN | TIMER_FMODE which currently is 0x1 | BIT(0)
= 0b1, and will become 0x1 | (0 << 1) = 0b1.
I checked PX30, RK3128, RK3188, RK3228, RK3288, RK3308, RK3328, RK3368
RK3506, RK3562 and RK3568 TRMs.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The free running mode is 0 at bit offset 1. User mode is 1 at bit offset
1. Currently, free running mode is 1 at offset 0, which is already the
case thanks to TIME_EN.
So, this essentially does not change the actual value written to the
register as it is TIME_EN | TIMER_FMODE which currently is 0x1 | BIT(0)
= 0b1, and will become 0x1 | (0 << 1) = 0b1.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The only difference with the implementation in spl_common.c is that we
check whether the timer has already been enabled. Considering this is
running in SPL, the first stage on RK3036, I feel like it's guaranteed
to not be enabled by default. No public TRM though and I don't have
access to an RK3036 device so take this as a guess.
Size of SPL binary increases by 8B for evb-rk3036.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Instead of redefining what is essentially the same code in
secure_timer_init, let's simply use rockchip_stimer_init from
spl_common.o instead.
This increases the size of the TPL by 16B, due to the added check of
STIMER already being enabled. Experimentally, STIMER is not already
enabled when in TPL.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Sige1 is a single board computer developed by ArmSoM, based on the
Rockchip RK3528A SoC.
Add support for the ArmSoM Sige1 board.
Features tested on a ArmSoM Sige1 v1.1:
- SD-card boot
- eMMC boot
- Ethernet
- USB host (with pending DT changes)
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The ROCK 2 Family is a high-performance SBC (Single Board Computer)
developed by Radxa, based on the Rockchip RK3528A.
The Radxa E20C shares some board characteristics with the ROCK 2 family
boards.
Add support for the ROCK 2A and 2F boards. The radxa-e20c-rk3528 target
is also extended to support booting ROCK 2 boards.
Features tested on a ROCK 2A v1.202:
- SD-card boot
- Ethernet
- USB host (with pending DT changes)
Features tested on a ROCK 2F v1.016:
- SD-card boot
- eMMC boot
- USB host (with pending DT changes)
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Luckfox Omni3576 Carrier Board with Core3576 Module, powered by the
Rockchip RK3576 SoC with four Cortex-A72 cores, four Cortex-A53 cores,
and a Mali-G52 MC3 GPU.
Features tested with a Core3576 Rev1.1 on a Omni3576 carrier board:
- SD-card boot
- eMMC boot
- LED
- PCIe/NVMe
- USB2.0 HOST
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Radxa ROCK 4D is a compact single-board computer (SBC) featuring
numerous top-tier functions, features, and expansion options.
Equipped with the Rockchip RK3576 or RK3576J SoC, the ROCK 4D boasts an
octa-core CPU (4x Cortex-A72 + 4x Cortex-A53), Mali-G52 GPU, and a
powerful 6 TOPS NPU, making it ideal for AI and multimedia tasks.
Features tested on a Radxa ROCK 4D v1.112:
- SPI Flash boot
- Ethernet
- PCIe/NVMe
- USB host
ROCK 4D boards with SPI Flash is configured to boot from FSPI0->UFS->USB,
or directly from USB when the MASKROM button is pressed, booting
directly from SD-card is not possible on these boards.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The bootsource ids reported by BootROM of RK3576 for SPI NOR and USB
differs slightly compared to prior SoCs:
- Booting from sfc0 (ROCK 4D) report the normal bootsource id 0x3.
- Booting from sfc1 M1 (NanoPi M5) report a new bootsource id 0x23.
- Booting from sfc1 M0 has not been tested (no board using this config).
- Booting from USB report a new bootsource id 0x81.
Add a RK3576 specific read_brom_bootsource_id() function to help decode
the new bootsource id values and the required boot_devices mapping of
sfc0 and sfc1 to help support booting from SPI flash on RK3576.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The bootsource ids reported by BootROM of RK3528 for e.g. USB differs
compared to prior SoCs:
- Booting from USB report a new bootsource id 0x81.
Add a RK3528 specific read_brom_bootsource_id() function to help decode
this new bootsource id value to help support booting from USB on RK3528.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The bootsource ids reported by BootROM of RK3528 and RK3576 for e.g.
SPI NOR and USB differs slightly compared to prior SoCs:
- Booting from sfc0 (ROCK 4D) report the normal bootsource id 0x3.
- Booting from sfc1 M1 (NanoPi M5) report a new bootsource id 0x23.
- Booting from sfc1 M0 has not been tested (no board using this config).
- Booting from USB report a new bootsource id 0x81 on RK3528 and RK3576.
Add a helper function to read the bootsource id. This helper function
will be used to translate the new values to the common BROM_BOOTSOURCE
enum values on RK3528 and RK3576.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The commit f8cb3fde93 ("arm: dts: rockchip: Fix eMMC write on RK3528")
added a missing mmc-hs200-1_8v prop to boart u-boot.dtsi.
Remove this boart u-boot.dtsi mmc-hs200-1_8v prop now that the board dt
from dts/upstream after the v6.17-dts sync includes this prop.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update rk3326-u-boot.dtsi to include OTP in U-Boot pre-reloc phase for
checkboard() to be able to read information about the running SoC model
and variant from OTP and print it during boot:
U-Boot 2025.07 (Jul 13 2025 - 10:07:16 +0000)
Model: ODROID-GO Super
SoC: RK3326
DRAM: 1 GiB (total 1022 MiB)
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
I have the ORDOID-GO Super variant of this board. Add myself as a
reviewer to help review future patches targeting this device.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable the default commands and some more useful commands that can be
useful to determin the state of the board from U-Boot CLI.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Use default-state prop to ensure that the blue heartbeat LED turns on
at boot to inticate that U-Boot proper has been reached.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable Kconfig options to support RockUSB, buttons, LEDs and RNG
featured on the board or SoC.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Change to dynamically select what storage media to use for the U-Boot
environment depending on from what storage media the FIT images was
loaded from, fall back to use env from nowhere.
U-Boot SPL 2025.07 (Jul 13 2025 - 10:07:16 +0000)
Trying to boot from MMC1
...
Loading Environment from MMC... Reading from MMC(0)...
or
U-Boot SPL 2025.07 (Jul 13 2025 - 10:07:16 +0000)
Trying to boot from SPI
...
Loading Environment from SPIFlash...
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Include FDTs for all three board variants in the FIT image and adjust
the board selection code to use correct FDT in U-Boot proper.
E.g. use the odroid-go3 DT for a ODROID-GO Super device:
U-Boot 2025.07 (Jul 13 2025 - 10:07:16 +0000)
Model: ODROID-GO Super
DRAM: 1 GiB (total 1022 MiB)
PMIC: RK817 (on=0x80, off=0x08)
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The ODROID GO2 devices come with onboard SPI flash, add support for
using the SPI flash.
The BootROM seem to expect the IDBlock at 64 KiB offset compared to the
typical 32 KiB offset from start of SPI flash used by other SoCs.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Include the RK817 PMIC in SPL and enable Kconfig options to power off
the handheld gaming device when it was powered on due to a power cable
plug-in event:
DDR3, 333MHz
BW=32 Col=10 Bk=8 CS0 Row=15 CS=1 Die BW=16 Size=1024MB
out
Power Off due to plug-in event
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Include pinctrl nodes and props for sdmmc, sfc and uart in SPL to ensure
pins are configured according to the device tree.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Drop SPL_DRIVERS_MISC, it is not needed/used on these devices.
Enable SPL_FIT_SIGNATURE to ensure the integrity of the FIT images
that are loaded into memory.
Change SPL_MAX_SIZE to 256 KiB, similar to other SoCs where TF-A is
loaded at 0x40000 offset from start of DRAM.
Enable SPL_DM_SEQ_ALIAS to ensure device aliases are applied in SPL.
Drop use of SPL_TINY_MEMSET, there is plenty room for the normal memset.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The handheld gaming devices that this defconfig tagets does not contain
an Ethernet port, remove Ethernet related Kconfig options.
They also do not contain any pwm-regulator in their DTs, remove the
PWM regulator related Kconfig option.
Display/video is not supported in U-Boot, remove all display/video
related Kconfig options.
There is no real functional change expected with these options removed.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a new common rk3326-u-boot.dtsi and move the SoC common overrides
into it.
This should not contain any changes other than a possible reorder of
nodes and props.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
GPIO devices are needed in U-Boot proper phase, sdmmc and sfc devices
are needed in SPL and pre-reloc phase.
Update bootph- props to match what boot phase devices are needed at.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
DTs from dts/upstream already contain aliases for i2c, mmc and serial.
Remove the aliases and status=okay that are already defined in upstream
board or SoC DT.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The alias spi0 is incorrectly being re-defined in board u-boot.dtsi to
the SPI flash controller instead of the actual spi0 controller.
SPI flash support is currently not working on odroid-go2 due to missing
Kconfig options and other required device tree changes.
Remove the re-defined alias for spi0 to allow use of the real spi0,
proper SPI flash support is introduced in a later patch.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add dummy implementation of set_rate for SCLK_GPU and SCLK_WIFI_PMU to
allow use of dts/upstream assigned-clocks in cru and pmucru nodes.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
A variety of Qualcomm features/fixes for this cycle, notably with a few
new platforms gaining support:
* Initial support for SDM670 (similar to SDM845), SM6350, and SM7150
platforms is added
* USB and UART issues on MSM8916 are addressed (improving stability/
reliability)
* Firmware loading is implemented for the GENI serial engine, this is
used on some platforms to load firmware for i2c/spi/uart to work
Some additional patches like binman support for building MBN files still
need some additional work.
CI: 8ef6ac07b3/pipelines
Enable the serial engine clk in probe so that this driver can work on
platforms that don't already initialize the clk for this device before
this driver runs. This fixes a problem I see on Coreboot platforms like
Trogdor where the UART hardware isn't enabled by coreboot unless the
serial console build is used.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://patch.msgid.link/20250714-geni-load-fw-v5-6-5abbc0d29838@linaro.org
Signed-off-by: Casey Connolly <kcxt@postmarketos.org>
Qualcomm peripherals like UART, SPI, I2C, etc are all exposed under a
common GENI Serial Engine wrapper device. Replace the stub driver we use
for this currently with a full-on misc device and implement support for
loading peripheral firmware.
Each of the peripherals has it's own protocol-specific firmware, this is
stored on the internal storage of the device with a well-known partition
type GUID.
To support this, GENI will bind peripherals in two stages. First the
ones that already have firmware loaded (such as the serial port) are
bound in the typical way. But devices that require firmware loading are
deferred until EVT_LAST_STAGE_INIT. At this point we can be sure that
the storage device is available, so we load the firmware and then bind
and probe the remaining children.
Child devices are expected to determine if firmware loading is necessary
and call qcom_geni_load_firmware().
Since Linux currently doesn't support loading firmware (and firmware may
not be available), we probe all GENI peripherals to ensure that they
always load firmware if necessary.
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
Link: https://patch.msgid.link/20250714-geni-load-fw-v5-3-5abbc0d29838@linaro.org
Signed-off-by: Casey Connolly <kcxt@postmarketos.org>
The change in commit c1af358cf5 ("imx: mx6ull: fix REFTOP_VBGADJ
setting") is not correct. According to latest i.MX6ULL fuse table,
the REFTOP_TRIM[2:0] fuse is defined as below. So the previous codes
are correct, only need to fix the comments.
Set the REFTOP_VBGADJ field in PMU_MISC0 register based on the
REFTOP_TRIM fuse:
'000" - set REFTOP_VBGADJ[2:0] to 3'b000
'001" - set REFTOP_VBGADJ[2:0] to 3'b001
'010" - set REFTOP_VBGADJ[2:0] to 3'b010
'011" - set REFTOP_VBGADJ[2:0] to 3'b011
'100" - set REFTOP_VBGADJ[2:0] to 3'b100
'101" - set REFTOP_VBGADJ[2:0] to 3'b101
'110" - set REFTOP_VBGADJ[2:0] to 3'b110
'111" - set REFTOP_VBGADJ[2:0] to 3'b111
Sven Schwermer reported:
"These are the symptoms: Very few of the thousands of devices that we
manufacture (< 1%) fail to decompress a large XZ archive once in Linux
userspace. We have not found any form of memory testing or other load
that reproduces this issue. Reverting the offending patch fixes this
behavior on the affected devices."
Revert the offending commit to fix the regression.
Reported-by: Sven Schwermer <u-boot@schwermer.no>
Signed-off-by: Ye Li <ye.li@nxp.com>
[fabio: Fixed checkpatch warning and added Sven's report]
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Commit 2a7acc865b ("configs: colibri-imx8x: enable RNG support for KASLR")
enables FSL_CAAM which requires initialization in arch_misc_init().
The ARCH_MISC_INIT configuration was added to the relevant defconfig.
Commit d0ed963690 ("global: Make ARCH_MISC_INIT a selected symbol")
changed ARCH_MISC_INIT to require explicit selection by the developer.
With this change the colibri-imx8x defconfig is no longer sufficient to
enable ARCH_MISC_INIT when FSL_CAAM is selected.
Add the necessary selection to automatically enable ARCH_MISC_INIT when
FSL_CAAM is enabled on i.MX8 platforms.
Fixes: d0ed963690 ("global: Make ARCH_MISC_INIT a selected symbol")
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This board is very tight on space in SPL; in fact with my compiler it
ends up just exactly on the wrong side:
spl/u-boot-spl.bin exceeds file size limit:
limit: 0xa000 bytes
actual: 0xa014 bytes
excess: 0x14 bytes
The repeated "lookup and request" pattern in spl_board_init() suggests
a low-hanging fruit for reducing the code size. This reduces the
object size of spl/board/liebherr/btt/btt.o by 300 bytes.
I've left the lack of error handling as-is; there isn't really
anything to do if it fails, so I suppose the printfs are the best that
can be done.
Signed-off-by: Rasmus Villemoes <ravi@prevas.dk>
NXP i.MX SoCs are available in different temperature grades. By default,
device-tree contains only thermal trips for consumer grade parts. On the
other hand, part temp grade fuse can be used to determine thermal trip
points. We already do this in imx_tmu_bind() function. Now, factor out
this functionality to a standalone function imx_tmu_set_trips() and use
it for both cases. This fixes an issue where 'cpu-thermal' child device
would set different thermal trips than the parent 'tmu@44482000' sensor,
depending on which gets used.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
The memory size of the 0098 SKU is 8 GB instead of 16 GB.
Fix PID4 0098 Aquila iMX95 definition.
Fixes: 4c93407165 ("toradex: tdx-cfg-block: add new pid4 support")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
CI: https://source.denx.de/u-boot/custodians/u-boot-mmc/-/pipelines/28083
- Add support for Samsung Exynos 7870 DW-MMC device
- Add support for Samsung S2MPU05 PMIC device
- Add compatible string for Exynos5250 in Exynos DW-MMC driver
- Add support for handling UHS-I voltage signaling without power-cycle
- Minor misc cleanup
Guard execute_tuning with MMC_SUPPORTS_TUNING, otherwise there will be
build failure:
drivers/mmc/exynos_dw_mmc.c:484:10: error: 'struct dm_mmc_ops' has no member
named 'execute_tuning'
.execute_tuning = exynos_dwmmc_execute_tuning,
^~~~~~~~~~~~~~
Cc: Kaustabh Chakraborty <kauschluss@disroot.org>
Acked-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reorder the SDHCI_INT_SPACE_AVAIL and SDHCI_INT_DATA_AVAIL flags in the
SDHCI_INT_DATA_MASK definition to match the bit order as defined in the
SDHCI specification and maintain consistency with the register layout.
The functional behavior remains unchanged as this only affects the
order of OR operations in the mask definition.
Signed-off-by: Tanmay Kathpalia <tanmay.kathpalia@altera.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Some boards have SD card connectors where the power rail cannot be switched
off by the driver. However there are various circumstances when a card
might be re-initialized, such as after system resume, warm re-boot, or
error handling. However, a UHS card will continue to use 1.8V signaling
unless it is power cycled.
If the card has not been power cycled, it may still be using 1.8V
signaling. According to the SD spec., the Bus Speed Mode (function group 1)
bits 2 to 4 are zero if the card is initialized at 3.3V signal level. Thus
they can be used to determine if the card has already switched to 1.8V
signaling. Detect that situation and try to initialize a UHS-I (1.8V)
transfer mode.
Signed-off-by: Tanmay Kathpalia <tanmay.kathpalia@altera.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Samsung S2MPU05 PMIC is used in devices with the Exynos7870 SoC, it
houses voltage regulators and an RTC module. Add support for this device
variant in the driver, which also binds the corresponding voltage
regulator driver.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Samsung's S2MPU05 PMIC is used by Exynos7870 SoC. It has 5 buck and 38
LDO regulators. Add support for this device variant in the driver.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The functions s2mps11_{buck,ldo}_mode use the s2mps11_{buck,ldo}_modes
arrays directly in order to extract the mode of a certain register.
This approach does not allow similar devices of other variants (which
may support a different set of modes) to work with the same driver.
Instead of using these arrays hardcoded, extract them from the device's
uclass platform data. Now the responsibility of setting these arrays
properly is done by functions s2mps11_{buck,ldo}_probe, by implementing
a switch-case block which can support modes of multiple variants if and
when added.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In the Linux kernel driver, all information related to LDO and BUCK
regulators are stored in descriptive arrays. This also allows multiple
variants to be supported by the same driver.
Define a struct sec_regulator_desc which holds all values required by a
regulator. Create an array of said struct containing all regulators. The
descriptors are designed to follow a style similar to what's seen in the
Linux driver, so comparing one with the other is simple.
In functions such as s2mps11_{buck,ldo}_{val,mode} these values are to
be used, make necessary modifications to pull them from the descriptors.
Since multiple variants have varying descriptors, select them from
within a switch-case block.
Functions s2mps11_{buck,ldo}_{volt2hex,hex2volt} and arrays
s2mps11_buck_{ctrl,out} are phased out as the calculations are now
hardcoded in descriptors, thusly, it reduces clutter and enhances
readability.
Two macros in s2mps11.h, S2MPS11_LDO_NUM and S2MPS11_BUCK_NUM are
removed as they are no longer being used.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
There are multiple PMICs by Samsung which are similar in architecture
(register layout, interface, etc.) and is possible to be driven by a
single driver. Variant specific code and data should be managed properly
in the driver.
And an enum which describes all supported variants. Pass the enum as the
device driver data. Introduce a switch-case block on the enum for any
variant specific code.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The probe function, s2mps11_probe() is responsible for binding its PMIC
children. The driver doesn't have any functionality directly, but has
sub-devices which are parts of the device. Therefore, this should be a
bind function. This is the case in the Samsung S5M8767 PMIC driver.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Exynos7870 is documented in upstream dt-schema. Add it in the U-Boot
driver.
Note that here it seems that Exynos7 DW MMC is perfectly compatible with
Exynos7870 DW MMC. It's not always true, especially in SDIO cards where
data from a 64-bit FIFO is read in two 32-bit halves [1]. Since SDIO
isn't used or implemented here, it's oblivious. But upstream's schema
considers that quirk, so that compatible is followed.
Link: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=7cbe799ac10f [1]
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
SD UHS mode is already supported by the Exynos DW-MMC driver in mainline
Linux. Using that as reference, add support in the U-Boot driver.
The maximum frequency was capped to 200000000, increase it to 208000000,
which is the required frequency for UHS_SDR104, which has the highest
frequency of all UHS modes. Moreover, add UHS_CAPS to host capailities.
These changes allow both host and card to recognize support for all UHS
modes.
SDR104, SDR50, and DDR50 have their own CLKSEL timing values, which
requires the CIU div value to be set in bits 18:16. Move the function
exynos_dwmci_clksel() below exynos_dwmmc_get_ciu_div() so that the
latter is accessible from the former, and add cases for said timing
modes.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
MMC HS200 and HS400 modes are already supported by the Exynos DW-MMC
driver in mainline Linux. Using that as reference, add support in the
U-Boot driver.
The maximum frequency was capped to 50000000, increase it to 200000000,
which is the required frequency for HS200/HS400. Moreover, add
MMC_MODE_HS200 and MMC_MODE_HS400 to host capailities. These changes
allow both host and card to recognize support for HS200/HS400.
This change also includes a new ops function, namely execute_tuning.
Implementing it would mean that we can no longer rely on the default ops
provided by dw_mmc.c, thus a new ops instance is created with proper
fields. The execute_tuning function is modeled after the one available
in the Linux driver.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Disrupting the regulator voltage during ios configuration messes with
the MMC initialization sequence. Move the VQMMC regulator enable/disable
functions to the MMC power cycle function, similar to how its done for
the VMMC regulator.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In certain cases, the VQMMC regulator may not support certain voltages.
For instance, a VQMMC regulator which supports only up to 2.7V will not
accept 3.3V as an argument. This is unaccounted for, and thus the driver
incorrectly assumes that the voltage is set successfully.
Fetch the return value in a variable and return if it's non-zero.
(-ENOSYS is exempted as it implies that the voltage adjustment
functionality as a whole isn't supported).
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
During a voltage switch command (CMD11, opcode: SD_CMD_SWITCH_UHS18V),
certain hosts tend to stop responding to subsequent commands. This is
addressed by introducing an additional command flag,
DWMCI_CMD_VOLT_SWITCH.
The associated interrupt bit is defined as DWMCI_INTMSK_VOLTSW. This is
set high when a voltage switch is issued, this needs to be waited for
and set to low. Implement the same in the timeout loop. Do note that
since DWMCI_INTMSK_VOLTSW shares the same bit as DWMCI_INTMSK_HTO (bit
10), the interrupt bit needs to be polled for only if the volt switch
command is issued.
DWMCI_CMD_VOLT_SWITCH also needs to be set for subsequent clken commands
after the volt switch. To ensure this, add a boolean member in the host
private struct (herein named volt_switching), which informs if the last
command issued was for volt switching or not.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The current implementation polls for the DWMCI_CMD register, for the
DWMCI_CMD_START bit to turn off, which indicates that the command has
been completed. The problem with this approach is that it doesn't
address the DWMCI_INTMSK_CDONE bit in the interrupt register,
DWMCI_RINTSTS. As a result, subsequent commands result in timeout errors.
Re-implement the waiting logic by polling for said interrupt status bit
and setting it low if raised.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In dwmci_setup_bus(), if the requested frequency is equal to the current
frequency, the function is returned, assuming no changes are required in
associated registers.
On certain SD cards, skipping in such situations may result in a timeout
errors during MMC initialization. Due to the lack of documentation, the
cause is unknown, but removing said check seems to fix the issue.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
These commands are required by struct dm_mmc_ops. Any platform specific
driver may use some or all of the functions in their own ops. Make them
accessible by moving the prototype to the dwmmc.h header.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This driver got successfully tested with an upstream device tree
and an Exynos5250. The board in question is samsung-manta
(Google Nexus 10) which we are getting ready for upstream.
For the u-boot port was just this additional compatible string needed.
Signed-off-by: Lukas Timmermann <uboot@timmermann.space>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The UART DM controller supports different channel data packing modes,
either the 4-character packing mode (where 32-bit are read/written at once)
or the single-character mode (where only a single character is read/written
at a time). The 4-character mode can be more efficient, but the
single-character mode is much easier to implement.
At the moment, serial_msm uses the 4-character mode. Since the
dm_serial_ops operate on one character at the time, the code goes through
quite some hoops in order to break this down to single characters. This
code is prone to race conditions (e.g. priv->chars_cnt is read from the
registers, then a command is issued, what if another char came in
inbetween?). It also seems to cause another subtle issue with autoboot:
Unlike the previous autoboot failures that happened when UART was
disconnected, this problem occurs when UART is connected and open in a
terminal: For EFI boot, the console size is queried in efi_console.c
query_console_serial() by sending an ANSI escape code via UART. For some
reason, with the current driver we get yet another 0x00 byte (UART break
event?) when reading the reply from serial input. Because of that, reading
the console size fails in efi_console.c, the actual reply remains in the
UART buffer, and later the boot flow aborts because it detects input after
printing a prompt.
Rather than trying to fix the issue in the current complicated approach,
switch the driver to use the single-character mode. This is simple and
straightforward to implement without race conditions:
- We write one character at a time to UARTDM_TF, as long as the TX FIFO
has space available (TX_READY). To flush the console before starting
Linux, we wait for TX_EMPTY.
- We read one character at a time from UARTDM_RF and strip off the
additional error information (assuming there is something in the
RX FIFO, as indicated by RX_READY).
In this mode, querying the serial console size works and autoboot is no
longer interrupted. The overall code is also much shorter.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Tested-by: Alexey Minnekhanov <alexeymin@minlexx.ru>
Acked-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250908-db410c-autoboot-fixes-v2-6-316ed98e0143@linaro.org
Signed-off-by: Casey Connolly <kcxt@postmarketos.org>
There have been issues with autoboot on DB410c for years, where autoboot
gets interrupted by spurious input on the UART console. Back in 2021, I've
tried to fix this by inserting a delay before UART initialization, but it
has turned out this is not working reliably either.
It looks like the root cause has always been the lack of bias-pull-up,
which was causing the RX line to be floating when UART is disconnected.
The delay does not seem to be needed anymore when applying bias-pull-up,
so drop it again in favor of the proper fix.
This reverts commit ad7e967738.
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Tested-by: Alexey Minnekhanov <alexeymin@minlexx.ru>
Acked-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250908-db410c-autoboot-fixes-v2-2-316ed98e0143@linaro.org
Signed-off-by: Casey Connolly <kcxt@postmarketos.org>
The GPIOs on PM6350 work fine using the qcom_spmi_gpio driver and
enables the use of the Volume Up button Fairphone 4 smartphone.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Add the pm6150l regulator data found on the Qualcomm SM6350 platform.
The tables are imported from the Linux driver. The SMPS regulators were
not added now.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Add support for TLMM pin controller block (Top Level Mode Multiplexer)
on SM6350 SoC, with support for special pins.
Correct pin configuration is required for working debug UART and eMMC/SD
cards.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
This reverts commit 644b4650ee.
While the intention of the above commit is correct, it leads to test
failures in CI that need to be addressed at the same time.
Signed-off-by: Tom Rini <trini@konsulko.com>
This driver references the get_timer macro while relying on an
indirection inclusion of <time.h>. Add the missing include directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
A few spi drivers cannot build without access to some platform
specific header files. Express those requirements in Kconfig as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
A few clock drivers cannot build without access to some platform
specific header files. Express those requirements in Kconfig as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
There is nothing x86-centric in this include file, and moving it will
allow for some drivers to be compile-tested on sandbox.
Signed-off-by: Tom Rini <trini@konsulko.com>
When printing the contents of an lbaint_t variable we need to use LBAF
to print it in order to get the correct format type depending on 32 or
64bit-ness.
Signed-off-by: Tom Rini <trini@konsulko.com>
When printing the contents of an size_t variable we need to use z prefix
to the format character in order to get the correct format type
depending on 32 or 64bit-ness.
Signed-off-by: Tom Rini <trini@konsulko.com>
This feature requires that CFG_SYS_FLASH_BASE is defined and this in
turn is only done in the case of FLASH_CFI_DRIVER && !CFI_FLASH or in
other words, when DM_MTD is not enabled.
Signed-off-by: Tom Rini <trini@konsulko.com>
The function mtd_read_oob_bf is called by cmd/nand.c but does not have a
prototype in any header. Add this to include/linux/mtd/mtd.h as that is
the most logical place currently.
Fixes: 1fac577207 ("nand: Add a watch command")
Signed-off-by: Tom Rini <trini@konsulko.com>
In this header we make direct references to some dm/device.h functions
while not including the header directly. Add the missing include.
Signed-off-by: Tom Rini <trini@konsulko.com>
In nand_wait_ready there is a loop that includes a NULL check for
chip->dev_ready before it is dereferenced. Use a NULL check once the
loop is exited as well to cover the case where it exits due to a timeout
and it is therefore not known if chip->dev_ready is NULL or not.
This issue found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
ret maybe used uninitialised in some cases so instead
initialise it first to prevent this.
This issue was found by Smatch.
Fixes: 9671243e8d (cmd: mtd: Use the subcmd infrastructure to declare mtd sub-commands)
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
As the code is today, we get a warning about "select" statements on
"choice" options not doing anything. This is why for all of the boards
which had an 'imply MULTI_DTB_FIT_USER_DEFINED_AREA' they then also had
to set the option in the defconfig. Drop the imply lines here.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add UFS driver for UFS controller present on Renesas R-Car X5H R8A78000.
The controller uses different initialization code compared to previous
generation UFS controller present in Renesas R-Car S4 R8A779F0, and the
majority of the driver is the initialization, hence a new driver.
[Marek: Clean driver up, add SCMI reset handling, use read_poll_timeout(),
pass error values out of ufs_renesas_pre_init(), change the
compatible string to "renesas,r8a78000-ufs" to align with
previous generation "renesas,r8a779f0-ufs"]
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Tuyen Dang <tuyen.dang.xa@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20251028142335.18125-7-marek.vasut+renesas@mailbox.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
In _spi_get_bus_and_cs the check for stacked parallel support needing
multiple chip select support does a direct return on error. Instead it
should set the error code in ret and then use the unwind goto.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
In erratum_err050568 the test for apllicability uses logical or to check
multiple chip IDs but this means the test will always evaluate to true
as at least 1 term will always be true. Logical and should have been
used so that the expression evaluates to true if all terms are true
which would mean that no chip ID of interest was in use.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
In npcm_fiu_uma_operation to enter a code block nbytes must be non-zero.
So testing for nbytes inside the code block is redundant and can be
removed.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
In ich_spi_exec_op_swseq the variable with_address is only assigned a
value in the case of op->addr.nbytes being non-zero.
Initialise with_address to zero. so that it is always valid.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
In clk_set_default_get_by_id ret is passed to ERR_PTR but nothing is
done with the value that this calculates which is obviously not the
intention of the code. This is confirmed by the code around where this
function is called.
Instead return the value from ERR_PTR.
This issue found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Acked-by: Quentin Schulz <quentin.schulz@cherry.de>
In owl_mmc_prepare_data there is a NULL check for the pointer data but
it happens after data has already been dereferenced. Refactor the code
so that the NULL check happens before any code dereferences data.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
In intel_gpio_set_flags the two variables or0 and or1 may be used
uninitialised. Correct this by setting initial values in the
declaration.
Also there is no need to use '|=' when the initial value is 0 and there
is only one assignment performed to each variable so just use '='
instead.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
In spi_calibration if the low range fails to calibrate then the code
attempted to return the variable err but this has not been set in this
case. Instead just return -EIO.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
In cadence_qspi_apb_exec_flash_cmd the test for a timeout uses a
post-decrement on the variable retry which will result in a value of -1
after the loop exit, or it would if the variable were signed.
To fix this make retry a signed variable and test its value for being
equal to -1.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
A UFS device needs its bRefClkFreq attribute set to the correct value
before switching to high speed. If bRefClkFreq is set to the wrong
value, all transactions after the power mode change will fail.
The bRefClkFreq depends on the host controller and the device.
Query the device's current bRefClkFreq and compare with the ref_clk
specified in the device-tree. If the two differ, set the bRefClkFreq
to the device-tree's ref_clk frequency.
Taken from Linux kernel v6.17 (drivers/ufs/core/ufshcd.c and
include/ufs/ufs.h) and ported to U-Boot.
Signed-off-by: Jared McArthur <j-mcarthur@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Link: https://patch.msgid.link/20251010195556.1772611-3-j-mcarthur@ti.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Commit d232d7fdbf ("ufs: core: sync ufshci.h with Linux v6.12") updated
the Data Direction values from bitmask values to simple enumerations.
Before:
enum {
UTP_NO_DATA_TRANSFER = 0x00000000,
UTP_HOST_TO_DEVICE = 0x02000000,
UTP_DEVICE_TO_HOST = 0x04000000,
};
Updated:
enum utp_data_direction {
UTP_NO_DATA_TRANSFER = 0,
UTP_HOST_TO_DEVICE = 1,
UTP_DEVICE_TO_HOST = 2,
};
However, the U-Boot code still uses these values directly without shifting,
and resulting in wrong bitfield placement in the Transfer Request
Descriptor.
This fixes the issue by applying the necessary shift to align the value.
Fixes: d232d7fdbf ("ufs: core: sync ufshci.h with Linux v6.12")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20251010024557.673787-1-hayashi.kunihiko@socionext.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
In ti_j721e_ufs_probe there is a call to clk_get_rate but the code after
that attempts to detect an error from that call incorrectly uses
IS_ERR_VALUE. Instead the test should just be for regular error codes.
The call returns an unsigned long so that needs to be cast to a signed type
first of all.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Reviewed-by: Anshul Dalal <anshuld@ti.com>
Link: https://patch.msgid.link/20251007-ufs_ti-v2-1-501f575b6947@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
In versaclock_probe vc5->pin_xin may be an error pointer so need to
check with IS_ERR before attempting to dereference it.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
In versaclock_get_name -ENOMEM is passed to ERR_PTR but nothing is
done with the value that this calculates which is obviously not the
intention of the code. This is confirmed by the code around where this
function is called.
Instead return the value from ERR_PTR.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
You cannot test an unsigned member of a struct for being negative, the
test will always fail. Instead assign the return value of
fdtdec_get_int, which returns an int, to a temporary variable declared
as an int, so that it can be tested for being negative before being
assigned to the unsigned struct member.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
epnum is used as an index into an array. The limit check for this index
should be performed before using it to access an element in the array to
prevent possible bounds overrun.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
A null check for the variable 'data' was introduced before dereferencing
it for set_phy_power but other uses were not so protected. Add the null
check for other dereferences of 'data'.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
The variable node is assigned to the return value of a function that
returns an int. It is tested for being negative and then passed as an
argument to a function that takes an int. So 'node' should not be
declared as unsigned. Correct it.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Combining two bits into a mask to be used so that the same write code
can be used to set or reset bits in a register clearly needs to use the
binary 'or' operator, not the binary 'and'. Fix it.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
When a variable needs a null check before it is dreferenced ensure that
this is done even in the case of assignment on declaration. This was not
happening for lurb_priv so correct it.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
fsl_fdt_fixup_usb_erratum uses strcmp to detect an error but then
returns 'err' without it being set to an error. Calling code may not
detect that an error occurred leading to a silent failure. Instead just
return -EINVAL.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
THe variable node is assigned to the return value of a function that
returns an int. It is tested for being negative and then passed as an
argument to a function that takes an int. So 'node' should not be
declared as unsigned. Correct it.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut@mailbox.org>
Add initial board docs for Milk-V Mars CM (eMMC) and Milk-V Mars CM Lite
(SD Card) to the visionfive2 board target.
Signed-off-by: E Shattow <e@freeshell.de>
Add Milk-V Mars CM and Mars CM Lite to visionfive2.
These boards were previously supported and then removed in the transition
to OF_UPSTREAM. The dts have landed in the for-next queue so let's add the
boards again.
Signed-off-by: E Shattow <e@freeshell.de>
Reviewed-by: Hal Feng <hal.feng@starfivetech.com>
Add identifier for Milk-V Mars CM to dts selection callback in SPL, and
to fdtfile environment variable default value selection in payload.
Signed-off-by: E Shattow <e@freeshell.de>
Reviewed-by: Hal Feng <hal.feng@starfivetech.com>
Prune overrides of upstream jh7110.dtsi now that the required nodes are
available through the devicetree-rebasing subtree.
Signed-off-by: E Shattow <e@freeshell.de>
Milk-V Mars CM Lite is a System-on-Module based on the Milk-V Mars CM
without the onboard eMMC storage component populated and configured
instead for SD3.0 Card Slot on that interface via 100-pin connector.
Link to Milk-V Mars CM Lite schematics: https://github.com/milkv-mars/mars-files/tree/main/Mars-CM_Hardware_Schematices
Link to StarFive JH7110 Technical Reference Manual: https://doc-en.rvspace.org/JH7110/TRM/index.html
Link to Raspberry Pi CM4IO datasheet: https://datasheets.raspberrypi.com/cm4io/cm4io-datasheet.pdf
Add the devicetree file to make use of StarFive JH7110 common supported
features PMIC, EEPROM, UART, I2C, GPIO, PCIe, QSPI Flash, PWM, and
Ethernet. Also configure the eMMC interface mmc0 for SD Card use and
configure the common SD Card interface mmc1 for onboard SDIO BT+WiFi.
Signed-off-by: E Shattow <e@freeshell.de>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
[ upstream commit: 4cce8b2503ab50f75a2dbc3eef2e55722836588e ]
(cherry picked from commit c7821d537e5a61e5d543588674b71fb43ec0665b)
Milk-V Mars CM is a System-on-Module based on the StarFive VisionFive 2
board and Radxa CM3 System-on-Module compatible with the Raspberry Pi
CM4IO Classic IO Board.
Mars CM SoM features:
- StarFive JH7110 System on Chip with RV64GC up to 1.5GHz
- AXP15060 Power Management Unit
- LPDDR4 2GB / 4GB / 8GB DRAM memory
- BL24C04F 4K bits (512 x 8) EEPROM
- GigaDevice 25LQ128EWIG QSPI NOR Flash 16M or SoC ROM UART loader for
boot (selectable by GPIO)
- eMMC5.0 8GB / 16GB / 32GB flash storage onboard
- AP6256 via SDIO 2.0 onboard wireless connectivity WiFi 5 + Bluetooth
5.2 (optional, present in models with WiFi feature)
- 1x Motorcomm YT8531C Gigabit Ethernet PHY
- IMG BXE-4-32 Integrated GPU with 3D Acceleration:
- H.264 & H.265 4K@60fps Decoding
- H.265 1080p@30fps Encoding
- JPEG encoder / decoder
Additional features available via 2x 100-pin connectors for CM4IO Board:
- 1x HDMI 2.0
- 1x MIPI DSI (4-lanes)
- 1x 2CH Audio out (via GPIO)
- 1x MIPI CSI (2x2-lanes or 1x4-lanes)
- 1x USB 2.0
- 1x PCIe 1-lane Host, Gen 2 (5Gbps)
- Up to 28x GPIO, supporting 3.3V
- UART x6
- PWM x8
- I2C x7
- SPI
- I2S
Link to Milk-V Mars CM schematics: https://github.com/milkv-mars/mars-files/tree/main/Mars-CM_Hardware_Schematices
Link to StarFive JH7110 Technical Reference Manual: https://doc-en.rvspace.org/JH7110/TRM/index.html
Link to Raspberry Pi CM4IO datasheet: https://datasheets.raspberrypi.com/cm4io/cm4io-datasheet.pdf
Add the devicetree file to make use of StarFive JH7110 common supported
features PMIC, EEPROM, UART, I2C, GPIO, eMMC, PCIe, QSPI Flash, PWM, and
Ethernet. Also configure the common SD Card interface mmc1 for onboard
SDIO BT+WiFi.
Signed-off-by: E Shattow <e@freeshell.de>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
[ upstream commit: 8d193bc0aa2e802be30de331317639482735d738 ]
(cherry picked from commit 8e935d097e975e6322b63fdc8ef9894c8582bef0)
Add a common board dtsi for use by Milk-V Mars CM and Milk-V Mars CM Lite.
Signed-off-by: E Shattow <e@freeshell.de>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
[ upstream commit: 651b30c58775e334c79aa3ecd44a3d98ac201db2 ]
(cherry picked from commit 034af14dcd1e6dbfa4f41a340b6d92b054604858)
Relax no-sdio restriction on mmc1 for jh7110 boards. Property was
introduced for StarFive VisionFive2 dts to configure mmc1 for SD Card
but this is not necessary, the restriction is only needed to block use of
commands that would cause a device to malfunction.
Signed-off-by: E Shattow <e@freeshell.de>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
[ upstream commit: 481ee0fcbb9a0f0706d6d29de9570d1048aff631 ]
(cherry picked from commit b4e73596622f791e3c2a2449022671e4e579fbd0)
The current sifive_clint driver can fully support GHRTv2 clint.
Add the compatible of GHRTv2 clint, sifive,clint2, to sifive_clint_ids
list.
Signed-off-by: Vincent Chen <vincent.chen@sifive.com>
Signed-off-by: Wayling Chen <wayling.chen@sifive.com>
Signed-off-by: Max Hsu <max.hsu@sifive.com>
Signed-off-by: Jimmy Ho <jimmy.ho@sifive.com>
Combining two bits into a mask requires the use of the binary 'or'
operator not the logical one. Correct it.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Svyatoslav Ryhel <clamor95@gmail.com>
The goto immediately after a return is unreachable. Remove it and its
target label as redundant.
This issue was found by Smatch.
Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Svyatoslav Ryhel <clamor95@gmail.com>
This driver relies on tegra-specific headers to compile so make it
depend on ARCH_TEGRA.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Svyatoslav Ryhel <clamor95@gmail.com>
Bind watchdog driver to the Tegra timer node since it uses one of the
timers to act as a watchdog and has no dedicated hardware block.
Signed-off-by: Lukasz Majewski <lukma@nabladev.com>
Reviewed-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Provide support for Tegra watchdog functionality. The WATCHDOG index 0 in
conjunction with TIMER 5 is used inline with existing Linux kernel driver.
Signed-off-by: Lukasz Majewski <lukma@nabladev.com>
Reviewed-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Remove support for ATAGS-based OS booting. ATAGS are used for booting
older Linux kernel versions and we are moving away from using those.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
This commit introduces a port of the Linux kernel's driver for the
Mediatek's MT7621 I2C controller.
The port was undertaken as the existing driver intended for Mediatek
I2C controllers (mtk_i2c.c) is not compatible with the MT7621.
To use the driver:
1. Ensure that the mode of the i2c pin group is
configured for "i2c" rather than "gpio".
2. Delete the existing (bitbanged) i2c node from
arch/mips/dts/mt7621.dtsi, or specify:
/delete-node/ &i2c;
3. Declare:
i2c: i2c@1e000900 {
compatible = "mediatek,mt7621-i2c";
reg = <0x1e000900 0x100>;
clocks = <&clk50m>;
clock-names = "sys_clock";
resets = <&rstctrl RST_I2C>;
reset-names = "i2c_reset";
pinctrl-names = "default";
pinctrl-0 = <&i2c_pins>;
#address-cells = <1>;
#size-cells = <0>;
status = "okay";
};
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Reviewed-by: Heiko Schocher <hs@nabladev.com>
2025-10-28 09:49:57 +01:00
906 changed files with 39314 additions and 9391 deletions
/* SCMI shared memory buffer must be mapped as non-cacheable. */
.virt=0x2201f000UL,
.phys=0x2201f000UL,
.size=0x1000UL,
.attrs=PTE_BLOCK_MEMTYPE(MT_DEVICE_NGNRNE)|
PTE_BLOCK_NON_SHARE|
PTE_BLOCK_PXN|PTE_BLOCK_UXN
},{
.virt=0x22020000UL,
.phys=0x22020000UL,
.size=0x1e0000UL,
.attrs=PTE_BLOCK_MEMTYPE(MT_NORMAL)|
PTE_BLOCK_OUTER_SHARE|
PTE_BLOCK_PXN|PTE_BLOCK_UXN
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
